OPERATING GUIDE
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd
1
9/1/10 2:53 PM
WARNING
Important Safety InformatIon
______________________________________________________________________________________
• Not for use with aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is
prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner
and others. If you are unsure whether this product is appropriate for your dog, please consult your
veterinarian or a certified trainer.
• This device contains Nickel-metal hydride (NiMH) batteries; never incinerate, puncture, deform, short-
circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may
occur if this warning is not followed.
ExPlANATION Of ATTENTION WORDs AND symbOls UsED IN ThIs GUIDE
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
• RISk OF ExPLOSION IF BATTERy IS REPLACED By AN INCORRECT TyPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
WARNING
CAUTION
Please read and follow the instructions in this manual. Proper fit of the collar is important.
CAUTION, used without the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in harm to your dog.
A collar worn for too long, or made too tight on the dog’s neck may cause skin damage. This is called bed
sores; it is also called decubitus ulcers or pressure necrosis.
CAUTION
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
For additional information on bed sores and pressure necrosis, please visit the FAQ section for remote
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable while they
wear stainless steel contacts. Some dogs are sensitive to contact pressure. you may find after some
time that your dog is very tolerant of the collar. If so, you may relax some of these precautions. It is
important to continue daily checks of the contact area. If redness or sores are found, discontinue use
until the skin has fully healed.
• you may need to trim the hair in the area of the Contact Points or switch to the longer Contact Points to
ensure consistent contact. Never shave the dog’s neck; this may lead to a rash or infection.
• you should not make the collar any more tight than is required for good contact. A collar that is too tight
will increase the risk of pressure necrosis in the contact area.
2
1-800-732-0144
3
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 2-3
9/1/10 2:53 PM
Thank you for choosing SportDOG Brand.® Used properly, this product will help you train your dog
efficiently and safely. To ensure your satisfaction, please review this owner’s manual thoroughly. If you
have questions regarding this product’s operation, please see this manual’s Frequently Asked Questions
or Troubleshooting section, contact our Customer Care Center at 1-800-732-0144, or visit our website at
ComponentS
To get the most protection out of your warranty, please register your product within 30 days at
and should you ever need to call the Customer Care Center, we will be able to help you faster. Most
importantly, SportDOG™ will never give or sell your valuable information to anyone. Complete warranty
table of ContentS
Components .............................................................................................................................................5
How tHe system works.......................................................................................................................5
key Definitions........................................................................................................................................6
prepare tHe remote transmitter ..................................................................................................7
prepare tHe Collar reCeiver.............................................................................................................8
fit tHe Collar reCeiver ......................................................................................................................10
finD tHe best intensity level for your Dog ............................................................................11
test ligHt instruCtions....................................................................................................................11
general training tips........................................................................................................................12
program tHe remote transmitter..............................................................................................12
matCH tHe Collar reCeiver anD remote transmitter ......................................................14
program tHe Collar reCeiver for two or tHree-Dog operation ..................................14
aCCessories ...........................................................................................................................................15
frequently askeD questions..........................................................................................................16
troublesHooting .................................................................................................................................17
terms of use anD limitation of liability..................................................................................18
fCC ComplianCe .....................................................................................................................................18
battery Disposal..................................................................................................................................19
sportDog aDD-a-Dog® reCeivers...................................................................................................20
How tHe SyStem workS
The SportDOG™ FieldTrainer® 400 & 400S have been proven safe, comfortable and effective for all dogs
over 8 pounds. Consistent, correct use of this product allows you to reinforce commands and correct
misbehavior from up to 400 yards. The Remote Transmitter sends a signal, activating the Collar Receiver
to deliver a harmless stimulation. With proper training, a dog will learn to associate this signal with a
command. Like all SportDOG products, this model features adjustable stimulation
levels so you can tailor the stimulation level to your dog’s temperament,
eliminating the risk of over-correction.
ImPORTANT: ThE fIElDTRAINER 400 & 400s hAvE A RANGE Of UP TO 400
yARDs. DEPENDING ON ThE WAy yOU hOlD ThE REmOTE TRANsmITTER,
ThE mAxImUm RANGE mAy vARy. fOR cONsIsTENT REsUlTs AT lONGER
RANGEs, hOlD ThE REmOTE TRANsmITTER IN A vERTIcAl POsITION
AWAy fROm yOUR bODy AND AbOvE yOUR hEAD. TERRAIN, WEAThER,
vEGETATION, TRANsmIssION fROm OThER RADIO DEvIcEs, AND OThER
fAcTORs WIll AffEcT ThE mAxImUm RANGE.
WARNING
Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior.
Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this
product is appropriate for your dog, please consult your veterinarian or a certified trainer.
4
1-800-732-0144
5
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 4-5
9/1/10 2:53 PM
key DefInItIonS
prepare tHe remote tranSmItter
chARGE ThE REmOTE TRANsmITTER
REmOTE TRANsmITTER: Transmits the radio signal
to the Collar Receiver. It is waterproof and can be
submerged in water to a depth of 25 feet.
INTENsITy DIAl: Provides multiple levels of
stimulation so you can match the correction to your
dog’s temperament.
TRANsmITTER INDIcATOR lIGhT: Indicates that a
button is pressed and also serves as a low-battery
indicator.
UPPER bUTTON: This button is factory-set to deliver
continuous stimulation.
lOWER bUTTON: This button is factory-set to deliver
momentary stimulation, or a “Nick.”
REmOTE TRANsmITTER
1. Lift the rubber cover protecting the Charging
Jack.
2. Connect one of the charger connectors to the
Charging Jack.
3. Plug the charger into a standard 120-volt AC
wall outlet.
4. Charge the Remote Transmitter for 24 hours
for the first charge. Recharges take only 12
hours. Note: the transmitter Indicator Light
will flash after 12 hours of charging. For the
first charge, continue to charge the Remote
transmitter for an additional 12 hours.
5. When charging is complete, replace the
rubber cover.
TRANSMITTER
ANTENNA
INTENSITy
SIDE
BUTTON
DIAL
TRANSMITTER
INDICATOR LIGHT
UPPER
BUTTON
LOWER
BUTTON
sIDE bUTTON: This button is factory-set to deliver a
tone without stimulation.
CHARGER CONNECTOR
PLACED IN THE
REMOTE TRANSMITTER
CHARGING JACk
chARGING JAcKs: For connecting the charger.
Although the Collar Receiver and Remote Transmitter
are waterproof without it, keep the cover in place when
not charging to keep debris out of the opening.
Note: Approximate battery life between
charges is 40 to 60 hours, depending on
frequency of use.
CHARGING
JACk
tranSmItter InDICator lIgHt
cOllAR REcEIvER: Receives the radio signal from the
Remote Transmitter and delivers the stimulation and/or
a tone for correcting your dog. It is waterproof and can
be submerged in water to a depth of 25 feet.
REcEIvER INDIcATOR lIGhT: Indicates when the Collar
Receiver has been turned on or off and also serves as a
low-battery indicator.
OPERATIONAl mODE
lIGhT cOlOR
bATTERy sTATUs lIGhT fUNcTION
cOllAR REcEIvER
Continuous stimulation or Green
Tone only button pressed
Good
Light is solid in color while
button is pressed
Light is solid in color while
button is pressed
Continuous stimulation or Red
Tone only button pressed
Low
cONTAcT POINTs: The contacts through which the
Collar Receiver delivers stimulation when a Remote
Transmitter button programmed for Continuous or
Momentary Stimulation is pressed.
ON/Off bUTTON: Momentarily pressing and holding
this button turns the Collar Receiver on and off.
Momentary stimulation
button pressed
Momentary stimulation
button pressed
Green
Good
Low
Light flashes once and
turns off
Light flashes once and
turns off
Light is solid in color while
on the charger
Light flashes once per
second once the battery is
completely charged
Red
Unit is charging
Red
Low
CHARGING
JACk
RECEIVER
INDICATOR LIGHT
ThE cOllAR REcEIvER Is cAPAblE Of DElIvERING
ThREE TyPEs Of cORREcTION:
Unit is fully charged
(charger still connected)
Green
Good
cONTINUOUs: you control both when and how long
stimulation is delivered, up to a maximum of 9 seconds.
After 9 seconds, the stimulation will “time out” and the
Remote Transmitter button needs to be released and
then pressed again before additional stimulation can be
delivered.
CONTACT POINTS
ON/OFF
BUTTON
mOmENTARy (NIcK): Stimulation is delivered for
5/100 of a second, regardless of how long the button is
pressed.
TONE: The Collar Receiver will make a rapid beeping
noise when a Tone button is pressed.*
*Tone comes preset and is not adjustable.
6
1-800-732-0144
7
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 6-7
9/1/10 2:53 PM
prepare tHe Collar reCeIver
reCeIver InDICator lIgHt
chARGE ThE cOllAR REcEIvER
OPERATIONAl
lIGhT lIGhT
bATTERy sPEAKER
mODE
Unit is charging
< 12 hours
Unit is charging
> 12 hours
Unit is turned on via
On/Off Button
Unit is turned off via
On/Off Button
Unit is turned off via
On/Off Button
cOlOR fUNcTION
sTATUs
N/A
fUNcTION
N/A
1. Lift the rubber cover protecting the
Charging Jack.
2. Connect the charger connector to
the Charging Jack.
3. Plug the charger into a standard
120-volt AC wall outlet.
4. Charge the Collar Receiver for 24
hours for the first charge. Recharges
take only 12 hours.
Note: the Receiver Indicator Light
will flash after 12 hours of charging.
For the first charge, continue to
charge the Collar Receiver for an
additional 12 hours.
5. When charging is complete, replace
the rubber cover.
Red
Light is solid
Green Light is flashing once per
second
Green Light is solid in color during N/A
beep sequence
Green Light is solid in color during Good
beep sequence
N/A
N/A
Beeps 5 times
Beeps 2 times
Beeps 2 times
N/A
Red
Light is solid in color during Low
beep sequence
Unit is on
Green Light flashes once per
second
Good
CHARGER CONNECTOR
PLACED IN COLLAR
RECEIVER CHARGING JACk
Unit is on
Red
Red
Red
Light flashes once per
second
Light is solid in color for as N/A
long as button is pressed
Light will quickly flash once N/A
no matter how long button
is pressed
Low
N/A
Unit is delivering
continuous stimulation
Unit is delivering
momentary stimulation
N/A
If the Collar Receiver is used in or around salt water, the Collar Receiver should be rinsed with
fresh water following each use. Prior to rinsing, the rubber charging jack cover should be
removed from the power plug socket and left out until the Collar Receiver has air dried.
N/A
Unit is delivering tone Off
N/A
N/A
Unit will beep
for as long
as button is
pressed
TO TURN ThE cOllAR REcEIvER ON:
1. Momentarily press and hold the
On/Off Button until the Receiver
Indicator Light comes on and the
Collar Receiver beeps 5 times.
2. Release the On/Off Button.
REchARGEAblE bATTERIEs
WARNING
• This device contains Nickel-metal hydride (NiMH) batteries; never incinerate, puncture, deform,
short-circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or
bodily harm may occur if this warning is not followed.
• Risk oF explosioN iF baTTeRy is Replaced by aN iNcoRRecT Type. dispose oF used
baTTeRies accoRdiNg To THe iNsTRucTioNs (page 19).
The Receiver Indicator Light will flash
until the Collar Receiver is turned off.
The flashing light indicates the Collar
Receiver is ready to receive a radio
signal from the Remote Transmitter.
ON/OFF BUTTON
• The rechargeable Nickel-metal hydride (NiMH) batteries are not memory sensitive and do not require
depletion before charging. Batteries should never be removed from the battery compartment for
charging.
TO TURN ThE cOllAR REcEIvER Off:
• The batteries come partially charged from the factory, but will require a full charge before the first
use (24 hours).
1. Momentarily press and hold the On/Off Button until the Receiver Indicator Light comes on
solid and the Collar Receiver beeps 2 times.
• when storing the unit for long periods, remember to regularly give batteries a full charge (12 hours). this
should be done once every 4 to 6 weeks.
2. Release the On/Off Button.
To extend the life between charging cycles, turn the Collar Receiver off when it is not in use.
• To maximize battery life, after initial charge, it is not recommended to leave the battery plugged in for
more than 12 hours.
• If your equipment has not been charged for an extended period, you may experience a decrease in
battery life the first few uses. Afterwards, the battery life will return to previous capacity levels.
Note: Approximate battery life between charges is 40 hours, depending on frequency of use.
8
1-800-732-0144
9
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 8-9
9/1/10 2:53 PM
2. The Collar Receiver should fit snugly, yet loose enough to allow
one finger to fit between the strap and your dog’s neck (3C).
3. Allow your dog to wear the collar for several minutes, and then
recheck the fit. Check the fit again as your dog becomes more
comfortable wearing the Collar Receiver.
3c
• You should expect hundreds of recharge cycles from your batteries. However, all rechargeable
batteries lose capacity over time relative to the number of recharge cycles they experience. This is
normal. If your operating time drops to half of the original life, contact the Customer Care Center to
purchase a new battery.
• The batteries should last for a period of 3-5 years. When a battery needs replacement, you can order
a new pack by calling our Customer Care Center at 1-800-732-0144, or by visiting our website at
received the replacement.
fInD tHe beSt IntenSIty level for your Dog
The FieldTrainer® 400 & 400S have multiple intensity levels. This allows you to choose the
stimulation that is best for your dog.
fIt tHe Collar reCeIver
ImPORTANT: The proper fit and placement of the collar Receiver is important
Note: Always start at the lowest level and work your way up.
for effective training. The contact Points must have direct contact with your dog’s skin.
For training efficiency, it is important to find the right intensity level for your dog. This is called
the Recognition Level, at which your dog looks around in curiosity, or flicks his ears.
Please read and follow the instructions in this manual. Proper fit of the collar
is important. A collar worn for too long, or made too tight on the dog’s neck may cause skin
damage. This is called bed sores; it is also called decubitus ulcers or pressure necrosis.
CAUTION
fINDING yOUR DOG’s REcOGNITION lEvEl:
Note: every dog is different and you cannot predict where your dog’s Recognition Level
will be. Watch closely for any slight change in behavior that tells you your dog is feeling the
stimulation.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the
contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
For additional information on bed sores and pressure necrosis, please visit the FAQ section
1. With the Collar Receiver turned on and properly fitted to your dog, set the Remote
Transmitter’s Intensity Dial at Level 1 and press the Continuous Stimulation Button for 1 to
2 seconds.
2. If your dog shows no reaction to Level 1, go to Level 2 and repeat the process.
3. yOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STIMULATION. IF THIS
HAPPENS, THE STIMULATION LEVEL IS TOO HIGH AND yOU NEED TO GO BACk TO THE
PREVIOUS LEVEL AND REPEAT THE PROCESS.
4. Once you find your dog’s Recognition Level, this is the level you should use when you begin
a training exercise.
5. If you have progressed to Level 8 while searching for your dog’s Recognition Level and your
dog continues to show no response, check to see if Collar Receiver is snug against your
dog’s neck. Then go back to Intensity Level 1 and repeat the process. If your dog still does
not indicate he is feeling the stimulation, you have two options: you may either have to trim
the hair beneath the Contact Points or switch to the longer Contact Points included in your
system.
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable
while they wear stainless steel contacts. Some dogs are sensitive to contact pressure. you
may find after some time that your dog is very tolerant of the collar. If so, you may relax some
of these precautions. It is important to continue daily checks of the contact area. If redness
or sores are found, discontinue use until the skin has fully healed.
If after completing all of these steps your dog still does not indicate he is feeling the
stimulation, please contact Customer Care Center at 1-800-732-0144.
To ensure a proper fit, follow these steps:
3A
3b
1. With your dog standing (3a), center the
Collar Receiver so the Contact Points are
underneath your dog’s neck, touching the
skin (3b). If your dog has a long or thick
coat, you have two options to ensure
consistent contact: either trim the hair
teSt lIgHt InStruCtIonS
1. Turn the Collar Receiver on.
2. Hold the Test Light Contacts to the Contact Points.
3. Press a Stimulation Button on the Remote Transmitter.
4. The Test Light will flash.
Note: At higher Stimulation Levels, the test Light will flash
brighter.
5. Turn the Collar Receiver off.
around the Contact Points or switch to the longer Contact Points included with your system.
CAUTION
• you may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck;
this may lead to a rash or infection.
• you should not make the collar any more tight than is required for good contact. A collar that is
too tight will increase the risk of pressure necrosis in the contact area.
Save the Test Light for future testing.
Note: If the test Light does not flash, recharge the battery and re-test. If the test Light still does
not flash, contact the Customer Care Center at 1-800-732-0144.
10
1-800-732-0144
11
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 10-11
9/1/10 2:53 PM
mODE UPPER bUTTON
fUNcTION
lOWER bUTTON
fUNcTION
sIDE bUTTON
fUNcTION
Tone only
# Of
DOGs
general traInIng tIpS
bEfORE TRAINING yOUR DOG WITh ThIs PRODUcT:
1
2
3
Continuous Stimulation Momentary (Nick)
(Level set by Intensity
Dial)
Continuous Stimulation Continuous Stimulation Tone only
(Level set by Intensity
Dial)
1
1
1
you will have the most success using this remote trainer if you always remember to teach a
command before trying to reinforce the command with a remote trainer. We recommend that
you read the enclosed Training Guide and watch the enclosed DVD before training with this
remote trainer. your training will be easier and proceed faster if you follow the guidelines in
these teaching assistants. In addition, always keep the following training tips in mind:
• Eliminate one misbehavior or teach one obedience command at a time. If you move too fast
with the training, your dog may become confused.
Stimulation (Level set
by Intensity Dial)
with intensity level set
at the maximum (8)
Continuous Stimulation Continuous Stimulation Tone only
• Be consistent. Give your dog a tone and/or stimulation with each misbehavior.
• Do not overcorrect your dog. Use as few stimulations as possible to train your dog.
• Restrict your dog from situations in which he has a history of misbehaving unless you can
supervise him and use the FieldTrainer® 400 & 400S for applying tone or stimulation.
• If you notice one situation in which your dog misbehaves repeatedly, set up this situation as
a training session. This will dramatically increase your chances of success.
• If your dog has a timid reaction to the tone or stimulation (especially the first couple of
times), do not be alarmed. Redirect his attention to a simple and appropriate behavior (i.e. a
known command, such as “Sit”).
• Never use the FieldTrainer 400 & 400S to correct or eliminate any form of aggressive
behavior. If your dog exhibits such behavior, contact a professional trainer. Aggression in
dogs is the result of many factors – it may be a learned behavior or it may be brought on as a
result of fear. Another factor contributing to aggression in dogs is social dominance. Every
dog is different.
(Level set by Intensity
Dial)
two levels higher than
the setting on the
Intensity Dial
4
5
6
7
DOG 1
DOG 2
DOG 3
3*
1
Continuous Stimulation Continuous Stimulation Continuous Stimulation
(Level set by Intensity
Dial)
(Level set by Intensity
Dial)
(Level set by Intensity
Dial)
Continuous Stimulation Continuous Stimulation Tone only
with intensity level set with intensity level set
to high end of reading
on Intensity Dial
Continuous Stimulation Continuous Stimulation Momentary (Nick)
with intensity level set with intensity level set Stimulation (Level set
to high end of reading
on Intensity Dial
to low end of reading on
Intensity Dial
1
to low end of reading on by Intensity Dial)
Intensity Dial
At this point, your remote trainer is ready to use. The transmitter is factory set to mode 1, but
you may wish to change the mode to fit your situation. See Step 5 for an explanation of mode
options.
Continuous Stimulation Tone with one-second- Tone only
(Level set by Intensity
Dial)
1
delayed Continuous
Stimulation (Level set
by Intensity Dial)
program tHe remote tranSmItter
Note: Modes 1, 2, 3, 4 and 7 provide 8 levels of stimulation, which correspond to the setting of
the Intensity Dial. Modes 5 and 6 provide more “increments” to choose from -- a total of 16 levels
of stimulation. For example, in mode 5 with the Intensity Dial set at 2, the bottom button provides
level 3 of 16 and the top button provides level 4 of 16.
Note: the transmitter is factory set to mode 1. the mode of the Remote transmitter can be
changed to fit your type or style of training.
TO chANGE ThE mODE:
1. Referring to the table on the following page, adjust
the Intensity Dial to the mode you want to use.
2. Turn the Remote Transmitter over.
*For two or three-dog operation setup, refer to Step 7 on page 14.
3. With a pen or the tine on the buckle of your collar strap,
depress and release the mode button. When the mode
button is pressed, the Transmitter Indicator Light will be
solid in color. When it is released, it will flash the mode
selected.
For example, if mode 5 is desired, adjust the Intensity Dial to Level 5. Once the mode button
has been depressed, the Transmitter Indicator Light will be solid, and once the mode button is
released, the Transmitter Indicator Light will flash five times.
Note: Continuous Stimulation will transmit for no more than 9 seconds no matter how long the
button is pressed. to reactivate, release and repress the button.
12
1-800-732-0144
13
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 12-13
9/1/10 2:53 PM
matCH tHe Collar reCeIver anD remote tranSmItter
aCCeSSorIeS
To reset the Collar Receiver to work with a new Remote Transmitter or to reprogram a new
Collar Receiver to work with your existing Remote Transmitter:
To purchase additional accessories for your SportDOG Brand® FieldTrainer® 400 or 400S, contact the
near you.
1. Turn the Collar Receiver off.
cOmPONENT
PART NUmbER
SDT00-12465
SDT00-12464
SDT00-12496
SAC00-10815
SAC00-10816
SAC00-11921
SAC00-11820
SAC00-12795
SAC00-10817
SAC00-12796
SAC00-12873
SAC00-12874
SAC00-12650
SAC00-12571
SAC00-12570
SAC00-12527
SAC00-10996
SDT00-11910
SDT00-11907
2. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off
after 4-5 seconds. If the On/Off Button is released too early, the Receiver Indicator Light
will begin flashing as normal. If this occurs, start over and repeat from 1.
3. After the Receiver Indicator Light has turned off, release the On/Off Button.
4. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator
Light flashes 5 times. you may need to hold both units 2-3 feet from each other before this
occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has
been reset and will begin flashing as normal. If the Receiver Indicator Light does not flash 5
times, start over and repeat from 1.
Replacement Transmitter: SD-400/400S
Replacement Receiver (does not include collar strap): sD-400
Replacement Receiver (does not include collar strap): sD-400s
Replacement 3/4” Collar Strap (Blaze Orange)
Replacement 3/4” Collar Strap (Black)
Replacement 3/4” Collar Strap (Blue)
Replacement 3/4” Collar Strap (Red)
Replacement 3/4” Collar Strap (yellow)
Replacement 3/4” Collar Strap (Green)
Replacement 3/4” Collar Strap (White)
Transmitter Accessory Pack (Charge Port Plug & Screw)
Receiver Accessory Pack (Charge Port Plug & Screw)
Adapter
program tHe Collar reCeIver for two or tHree-Dog
operatIon
SportDOG™ Add-A-Dog® receiver(s) must be purchased to train additional dogs. Please refer
to the back cover for other compatible Add-A-Dog collar Receivers for this system.
1. Program the Remote Transmitter to mode 4 (see pages 12-13).
2. Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn
off in 4-5 seconds. If the On/Off Button is released too early, the Receiver Indicator Light
will begin its normal flashing. If this occurs, start over and repeat from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper button on the Remote Transmitter until the Receiver Indicator
Light flashes 5 times. you may need to hold both units 2-3 feet from each other. If the
Receiver Indicator Light does not flash 5 times, start over and repeat from A.
3. Program the second Collar Receiver using A through D above, but using the lower button
in place of the Upper button.
Contact Points (Short)
Contact Points (Long)
Lanyard
Car Charger
Transmitter Battery Replacement kit
Receiver Battery Replacement kit
4. Program the third Collar Receiver using A through D above, but using the side button in
place of the Upper button.
14
1-800-732-0144
15
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 14-15
9/1/10 2:53 PM
The Intensity Dial seems difficult to
rotate. Is this normal?
yes. This prevents accidental changes in intensity and
encourages an optimal waterproof seal. The knob will “break
in” and be slightly easier to turn as you use it.
frequently aSkeD queStIonS
Is the stimulation safe for my dog?
While the stimulation is unpleasant, it is harmless to your dog.
Electronic training devices require interaction and training from
the owner to achieve desired results.
can I attach a leash to the fieldTrainer DO NOT attach a leash to the FieldTrainer 400 & 400S. you
400 & 400s?
may put a separate non-metallic collar on your dog’s neck and
attach a leash. Be sure the extra collar does not interfere with
the Contact Points.
how old does a dog have to be before
your dog should be able to learn basic obedience commands
such as “Sit” or “Stay.” The Collar Receiver may be too large
for dogs under 8 pounds.
using the fieldTrainer® 400 & 400s?
can I program my fieldTrainer 400 &
400s to work with my other
yes. your FieldTrainer 400 & 400S will also work with
SportHunter® 800 and WetlandHunter® 400 systems. The units
will need to be matched (see Step 6).
sportDOG brand® systems?
Once my dog is trained and has been
obeying my commands, will my dog
have to continue to wear the collar
Receiver?
your dog may need to wear the Collar Receiver from time to time
for reinforcement. Also, many hunters keep the Collar Receiver
on their dog(s) while hunting for maximum control.
troubleSHootIng
Is the collar Receiver waterproof?
yes. If the rechargeable battery pack ever needs to be replaced,
make sure the o-ring and o-ring groove are free from dirt and
debris.
The answers to these questions should help you solve any problem you have with this system. If
they do not, please contact the Customer Care Center at 1-800-732-0144 or visit our website at
can my collar Receiver be used
around salt water?
If the Collar Receiver is used in or around salt water, the Collar
Receiver should be rinsed with fresh water following each
use. Prior to rinsing, the rubber charging jack cover should be
removed from the power plug socket and left out until the Collar
Receiver has air dried.
my dog is not responding when I
press a button.
• Check to see if the Collar Receiver has been turned on.
• If your range has reduced from the first time you have used
it, please check to see if the battery is low in either the
Remote Transmitter or Collar Receiver.
• Many factors can impact the range you have with the
FieldTrainer® 400 & 400S. For a list of these factors, please
refer to “How the System Works”.
• you can verify the Collar Receiver is delivering stimulation to
your dog by placing the test light, enclosed in your kit, on the
Collar Receiver. Please refer to the “Test Light Instructions”
on page 11 for details.
can I use the fieldTrainer 400 & 400s
yes, SportDOG Add-A-Dog® Collar Receivers must be
purchased and the Remote Transmitter must be changed to
mode 4. Please refer to back cover for a list of compatible Collar
Receivers.
with more than one dog?
can I use the fieldTrainer 400 & 400s
on aggressive dogs?
We do not recommend any of our products to be used on
aggressive dogs. We recommend you contact your local
veterinarian or professional trainer to determine if your dog
might be aggressive.
• Increase the Intensity Dial. Refer to “Find the Best Intensity
Level for your Dog” for more information.
• Make sure the Collar Receiver’s Contact Points are placed
snugly against your dog’s skin. Refer to “Fit the Collar
Receiver” for more information.
• you may need to switch to the longer Contact Points included
with your system, or trim the hair beneath the Contact
Points. Never shave the dog’s neck.
Will I get exactly 400 yards of range
with the fieldTrainer 400 & 400s?
The range you get with your FieldTrainer 400 & 400S will
vary according to terrain, weather, vegetation, as well as,
transmission from other radio devices. To get the maximum
amount of range, please refer to the “How the System Works”
section of this guide.
• If you notice your operating time dropping to about half
the original time, your Collar Receiver battery needs to be
replaced. Contact the Customer Care Center or visit our
website to purchase a new one.
how long can I continuously deliver
The maximum amount of time you can press the Continuous
Stimulation Button and deliver continuous stimulation to your
dog is 9 seconds. After 9 seconds, the Remote Transmitter will
“time-out,” and the Continuous Stimulation Button must be
released and pressed again.
stimulation to my dog?
The collar Receiver will not turn on.
• Make sure the Collar Receiver has been charged. For the
initial charge, be sure to charge it for 24 hours. Future
charges only take 12 hours.
What do I do if my dog’s neck becomes This condition is due to the Contact Points irritating the skin.
red and irritated?
Discontinue use of the Collar Receiver for a few days. If the
condition persists beyond 48 hours, see your veterinarian. Once
the skin returns to normal, resume use, and monitor the skin
condition closely.
The collar Receiver is not responding • Verify the Collar Receiver has been turned on. Refer to
to the Remote Transmitter.
“Turning the Collar Receiver On and Off”.
• Refer to “Match the Collar Receiver and Remote
Transmitter”.
16
1-800-732-0144
17
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 16-17
9/1/10 2:53 PM
termS of uSe anD lImItatIon of lIabIlIty
battery DISpoSal
This device contains a Nickel-metal hydride (NiMH) battery; never incinerate, puncture, deform,
short-circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur
if this warning is not followed.
1. TERms Of UsE
WARNING
This Product is offered to you conditioned upon your acceptance without modification
of the terms, conditions and notices contained herein. Usage of this Product implies
acceptance of all such terms, conditions, and notices.
This system operates on two NiMH battery packs (120mAh capacity for the Collar Receiver and 160mAh capacity
for the Remote Transmitter). Only replace with battery received from calling the Customer Care Center at
2. PROPER UsE
This Product is designed for use with dogs where training is desired. The specific
temperament of your dog may not work with this Product. We recommend that you not use
this Product if your dog is less than 8 pounds or if your dog is aggressive. If you are unsure
whether this is appropriate for your dog, please consult your veterinarian, certified trainer
or contact our Customer Care Center at 1-800-732-0144.
Separate collection of spent batteries is required in many regions; check the regulations in your area before
discarding spent batteries. Please see below for instructions on how to remove the battery from the product for
separate disposal.
AT END Of PRODUcT lIfE, UsE ThEsE bATTERy REmOvAl INsTRUcTIONs fOR fINAl DIsPOsAl
(DO NOT OPEN ThE cOllAR REcEIvER OR REmOTE TRANsmITTER UNTIl yOU hAvE REcEIvED ThE
REPlAcEmENT):
Proper use includes reviewing the entire Operating and Training Guide provided with your
Product and any specific Caution statements.
3. NO UNlAWfUl OR PROhIbITED UsE
• Using a #1 Phillips screwdriver, remove the case screws.
• Remove the case back or cover.
• Remove the old battery pack. Note: When removing the old battery pack, care must be taken when
gripping the connector firmly to avoid damaging the wires. Shorting the battery wires may cause fire or
explosion.
This Product is designed for use with dogs only. This dog training device is not intended
to harm, injure, or provoke. Using this Product in a way that is not intended could result in
violation of Federal, State or local laws.
4. lImITATION Of lIAbIlITy
In no event shall Radio Systems® Corporation be liable for any direct, indirect, punitive,
incidental, special or consequential damages, or any damages whatsoever arising out of or
connected with the use or misuse of this Product. Buyer assumes all risks and liability from
the use of this Product.
WARNING
RISk OF ExPLOSION IF BATTERy IS REPLACED By AN INCORRECT TyPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Note: these instructions are not valid for repair or battery replacement. Replacing the battery with a
battery not specifically approved by Radio Systems® Corporation may cause fire or explosion. Please call
the Customer Care Center at 1-800-732-0144 to avoid invalidating your warranty.
5. mODIfIcATION Of TERms AND cONDITIONs
Radio Systems Corporation reserves the right to change the terms, conditions and notices
under which this Product is offered.
This product is protected by the following patents:
U.S. Patent Numbers: 6,901,883; 7,017,524; D545,790.
fCC ComplIanCe
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a specific installation. If interference does occur to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Contact customer service or an experienced radio/TV technician for assistance.
Caution: Unauthorized changes or modifications to the equipment may violate FCC regulations and
could void the user’s authority to operate the equipment.
18
1-800-732-0144
19
Download from Www.Somanuals.com. All Manuals Search And Download.
400-696-4.indd 18-19
9/1/10 2:53 PM
|
SIIG Network Card 485 PCI User Manual
Silvercrest MP3 Player KH 2337 User Manual
Sony Binoculars DEV 3 User Manual
Sony Camcorder XCG 5005E User Manual
Sony Car Speaker CD DH899N User Manual
Sony Clock Radio SY ICF C8WM User Manual
StarTechcom TV Converter Box S3510BMU33 User Manual
Sterling Model Vehicle 6828810700 User Manual
Sterling Water System SGM 250A User Manual
Strong Pools and Spas Hot Tub Strong Spas The Antigua User Manual