INSTRUCTION
MANUAL
FOR SPEEDOTRON
BROWN LINE
EQUIPMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
Speedotron power supplies are equipped with arc-protected outlets. However, as with
any electrical equipment, arc-over (an electrical discharge between two physically dis-
connected electrical terminals) is a possibility. When light cables, flash tubes or power
cords are improperly seated, arc-over may occur. Also, if your light unit or power supply
malfunctions, or the power cord or the internal wiring in the studio is improperly termi-
nated or defective, there is a chance of arc-over when connecting or disconnecting light
units. Severe power supply damage and operator injury may result if arc-over occurs.
That is why in spite of the arc-protection feature of Speedotron power supplies, you
should always make sure your Model and Power switches are off when disconnecting or
connecting light units. Plug sync extension into Sync socket and connect the other end
to a PC cord designed for your camera or lens. The sync extension supplied with the
power supply accepts the standard AC twin-blade type sync connector. A standard AC
to PC sync cord will be required to connect the camera to the power supply's sync
extension.
GENERAL POWER SUPPLY INSTRUCTIONS
For maximum equipment life and for safe, dependable operation of power
supplies we advise you to follow these general rules.
Unpack equipment carefully. Examine all packing material. Should you notice any break-
age or defect, notify the dealer and carrier (if shipped to you) immediately. Then please
read all instructions before assembling your flash system in order to avoid damage to
your equipment or injury to yourself.
Before doing anything with the power supply make sure that the Model and Power
switches are in the off position.
Connect light head cable(s) to the Light Unit Outlet(s) on the power supply, selecting
the appropriate outlets for the desired power level.
A slave tripper (Speedotron #23510) may be installed in the Sync socket (in place of the
sync extension) to fire the power supply. If the power supply fails to flash when exposed
to another light source with the slave installed in the Sync socket, remove the slave,
rotate it 180° and reinstall it in the socket.
All Brown Line light units can handle at least 400 watt-seconds, and specific units are
designed for a maximum of 1200 or 1600 watt-seconds. For power supplies that can pro-
duce more than 400Ws of power, you must be very careful that the flash tube you are
using in your light unit can handle all the available power. Never subject a flash tube to
more watt-seconds than it is designed to handle. If you are not sure that your flash
tube can handle the power provided by the set-up you are using, check pages 25 and 26
in addition to the Power Distribution Chart on the side of your power supply. We recom-
mend that you purchase at least one light unit that will accept the full output of the
power supply.
Connect AC power cord into Power Input on power supply. A 3-terminal ground power
plug is utilized on Brown Line power supplies. For maximum performance and safety, it is
strongly suggested that the 3-terminal cord supplied with the power supply be properly
utilized and properly terminated at the main source of incoming power. Always use a
three-wire ground power cord and a properly grounded wall outlet with all Speedotron
power supplies. Failure to do so may cause the power supply to intermittently misfire.
We do not recommend using an adapter and installing into a 2-blade
outlet.
To connect light units, align the light unit plug with the power supply outlet and apply
even pressure while pushing. Black colored light unit connectors are of the “quick
release” type that only require pushing the connector firmly until it is fully seated. Silvery
colored light unit connectors must be threaded until they are fully seated. Both types
prevent accidental cable removal. Make sure all light unit cables are fimly seated to pre-
vent connector damage. Tape all cables to the floor and keep them out of the pathways
to prevent accidents.
Once the light units are properly assembled and installed, the power cord is installed
and the sync extension is connected, turn the Power switch on.
Now refer to the Operating Instructions section of this manual for information regarding
the proper use of your particular power supply.
Never attempt to make repairs to your Speedotron equipment. All electronic flash
systems operate on high voltage and high power. It is very dangerous to open a
power supply.
Never install light units while the power supply is turned on. Never insert or remove
flash tubes while the light unit is connected to the power supply. Be sure flash tubes
are fully seated into light unit sockets. (Read instructions in the Light Units section of
this manual for more information on light unit assembly and operation.)
In order to maximize the life of the power supply it is recommended that
the capacitors be "formed" when a pack is not in use for 30 days or more.
All that is required of the user is to turn on the power supply for about 10
to 20 minutes each month. This simple procedure prevents premature
failure by maintaining the "elasticity" of the capacitors.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ready/Push to flash button
Power on LED
Symmetrical/Asymmetrical
Full/Half/Quarter
OPERATING INSTRUCTIONS
Hi-temp LED
Power Model
Operation of the D604, D1204 and D1604 power supplies is simple and straight for-
ward. This sequence of operation is suggested for maximum life and dependability.
Make sure that the Model and Power switches are in the off position and the Push to
Reset button is fully depressed into its socket. Connect light head cable(s) to the Light
Unit Outlet(s) on the power supply. The outlets are wired in parallel so it does not
matter in what sequence light head cables are connected.
Never connect or disconnect light units while power is on. Do not insert or remove
flash tubes while power is on. Your Brown Line power supply is equipped with arc-pro-
tection, but should your light unit or power supply malfunction, or the power cord, or
even the internal wiring in the studio be improperly terminated or defective, the chance
of arc-over when connecting or disconnecting light units is greatly increased. Severe
power supply damage and operator injury may result if arc-over occurs when light units
are being disconnected or connected. To prevent this, you should always turn the power
supply off when disconnecting or connecting light heads.
Never subject a flash tube to more watt-seconds than it is designed to handle.
MW3 and M90 series (non-”Q”) light units have a maximum rating of 400Ws, while “Q”
versions are rated at 1200Ws. M11 light units are rated at 1200Ws* (with new MW9H
flashtubes) and M11Q light units are rated at 2400Ws. We strongly recommend that at
least one light unit in your system is capable of handling the maximum output of your
power supply. If you are not sure if your flash tube and light unit can handle the power
provided by the set up you are using, check pages 25 and 26 and the Power Distribution
Chart on the side of your power supply.
Power input
Light unit outlets
Sync
Push to reset
Audible recycle
GENERAL DESCRIPTION OF CONTROLS
Power – turns power supply on and off (flashes light units when turning off).
Model – turns model lamp(s) on and off.
Symmetrical/Asymmetrical – controls power distribution. In the symmetrical position,
power is split equally between all lights. In the asymmetrical position, power is
distributed unequally and modeling lamp brightness on light units in outlets 3 and 4
is reduced.
Full/Half (on D604) or Full/Half/1/4 (on D1204 and D1604) – controls the total amount
of power delivered to light unit outlets.
Ready/Push to Flash – combination ready light and test flash button. Illuminates in
green to indicate when power supply has recycled to 85%. Pressing the button
when illuminated triggers the flash for testing or open flash applications.
Audible Recycle – controls audible ready tone (on/off).
Connect AC power cord into Power Input on power supply, then plug into a properly
grounded outlet. Use proper 3-conductor grounded cord for operator safety and to
reduce self-firing and misfiring caused by static electricity. Set Full/Half/1/4 switch as
desired (Full/Half switch on D604). This switch reduces the total output of the power
supply. Do not switch the Full/Half/1/4 switch until ready light is illuminated. Failure to
follow this procedure may result in damage to the switch.
Plug sync connector into Sync socket and connect the other end to PC cord for camera.
Once the camera is connected, tripping the shutter will automatically trigger the flash.
Power On – green LED illuminates when power switch is turned on.
Hi-Temp – red LED lights, alarm tone sounds, when internal heat becomes excessive.
Sync – socket for sync extension or slave.
Push to Reset – resets circuit breaker. Circuit breaker disables power supply in case of
malfunction.
A slave tripper (Speedotron #23510), may be inserted into the Sync socket in place of
the PC cord. In this mode of operation, the slave will activate the power supply when it
senses a bright flash of light from another light source. If the power supply fails to flash
when exposed to another light source with the slave installed in the sync socket, it may
be necessary to remove the slave, rotate it 180° and reinstall it into the Sync socket.
Power Input – socket for AC power cord.
Light Unit Outlets (4) – sockets for connecting from one to four light units to power
supply.
*New MW9H flashtubes supplied with M11 light units handle up to 1200Ws.
The MW9M flashtubes have a maximum capacity of 1000Ws.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn on Power and Model switches. Wait until the green Ready/Push to Flash illumi-
nates and press to check if the unit is operational. The light unit(s) should flash instantly
when this button is pressed. If you wish to check the function of each individual light unit,
we recommend that you turn off the Model switch and hold your hand in front of (not
inside) the light unit to be tested. When you fire the unit you will feel the heat of the
flash. This method is suggested because it is often difficult to determine by sight if one
of the lights has failed to flash.
POWER DISTRIBUTION TABLES
On the side of the D604, D1204 and D1604 power supplies there is a Power Distribution
Table based on the full power setting. These tables should be used as guides for deter-
mining various lighting possibilities, guide numbers and exposures when using consistent
flash tubes and reflectors. When different flash tubes and/or reflectors are used actual
light output will vary, producing as much as a full f/stop discrepancy with the table.
Brown Line '04 power supplies, feature symmetrical and asymmetrical operation.
Symmetrical output means all light units share equal output. To determine power levels,
divide the maximum output by the number of light units to be used. In asymmetrical
mode, outlets 1 and 2 receive a greater portion of the total output than outlets 3 and 4.
(For specific power distribution refer to the charts below for the number and configura-
tion of the lights to be used.)
The D604, D1204 and D1604 power supplies are equipped with an audible ready
signal (may be turned off) and high temperature alarm. A short audible tone along with
a green Ready/Push to Flash light indicates that the power supply has recycled to 85
percent (ANSI standard). For very critical exposures, waiting several seconds after the
green Ready/Push to Flash light illuminates will ensure that the power supply is at 100
percent power. If the beep should prove distracting, depress the Audible Recycle switch
to eliminate this short tone. The green Ready/Push to Flash light will still continue to
illuminate.
D604 Power Distribution Table
Symmetrical
Any socket(s)
Asymmetrical
Prolonged rapid flashing or storage in a high temperature environment (like the trunk of
a car) or extended use in extremely warm environments may eventually produce enough
heat to set off a steady alarm tone and red Hi-Temp LED indicator. The power supply
should be turned off at the Power switch because continued use may cause severe dam-
age. When the power supply has sufficiently cooled, normal operation may be resumed.
(If the power supply is not turned off, the alarm will not clear.)
1 or 2
3 or 4
600
600Ws
300Ws
1 Light
450
150
300
2:1
2 Lights
300
300
1:1
When the power supply has been exposed to extreme cold weather for an extended
period of time, it is suggested that the unit be allowed to warm up to room temperature
before connecting it to an AC power line.
150 150
1:1
300
75
75
4:1:1
2:2:1
3 Lights
4 Lights
200Ws
150Ws
210 210
105
When disassembling the system, turn off Power and Model switches first. When the
Power switch is turned off, the power supply will discharge by flashing all light units.
Placing the Full/Half/1/4 switch into the full position before turning off Power will
ensure that all capacitors are discharged. If the power supply should be inadvertently
switched off at a lower power setting, DO NOT immediately switch to full power!
Damage to the switch may result. Wait at least 10 seconds before operating the
Full/Half/1/4 switch. Unplug the power cord and disconnect the light head cable(s).
180
180
45
45
4:4:1:1
Divide watt-seconds by 2 when using half power.
One light:
Symmetrical mode in any outlet, will receive 600Ws.
Asymmetrical mode in outlets 1 or 2, will receive
600Ws; when using outlets 3 or 4 output is 450Ws.
Two lights: Symmetrical mode, all outlets share an equal amount of
power. Two lights each receive 300Ws (600Ws divided by 2).
Asymmetrical mode
Combination 1: one light in outlet 1 or 2 receives 300Ws;
the second light in outlet 3 or 4 receives 150Ws.
Combination 2: in outlets 1 and 2 receive 300Ws each.
Combination 3: in outlets 3 and 4 will receive 150Ws each.
Following the table will quickly illustrate other combinations that are possible with up to
four light units on the D604.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
D1204 Power Distribution Table
D1604 Power Distribution Table
Symmetrical
Any socket(s)
Asymmetrical
Symmetrical
Any socket(s)
Asymmetrical
1 or 2
3 or 4
1 or 2
3 or 4
1600
1200
1600Ws
800Ws
1 Light
1200Ws
600Ws
1 Light
1200
400
900
300
800
2:1
600
2:1
2 Lights
2 Lights
800
800
1:1
600
600
1:1
400 400
1:1
300 300
1:1
800
200 200
280
4:1:1
2:2:1
600
150 150
210
4:1:1
2:2:1
3 Lights
4 Lights
532Ws
400Ws
3 Lights
4 Lights
400Ws
300Ws
560 560
420 420
480
480 120 120
4:4:1:1
360
360
90
90
4:4:1:1
Divide Watt-seconds by 2 when using half power.
Divide Watt-seconds by 4 when using quarter power.
Divide Watt-seconds by 2 when using half power.
Divide Watt-seconds by 4 when using quarter power.
One light:
Symmetrical mode in any outlet, will receive 1200Ws.
One light:
Symmetrical mode in any outlet will, receive 1600Ws.
Asymmetrical mode in outlets 1 or 2, will receive
Asymmetrical mode in outlets 1 or 2, will receive 1600Ws;
1200Ws; when using outlets 3 or 4 output is 900Ws.
when using outlets 3 or 4 output is 1200Ws.
Two lights: Symmetrical mode, all outlets share an equal amount
of power. Two lights each receive 600Ws (1200Ws
divided by 2).
Two lights: Symmetrical mode, all outlets share an equal amount of power.
Two lights each receive 800Ws (1600Ws divided by 2).
Asymmetrical mode
Asymmetrical mode
Combination 1: one light in outlet 1 or 2 receives 800Ws;
the second light in outlet 3 or 4 receives 400Ws.
Combination 2: in outlets 1 and 2 receive 800Ws each.
Combination 3: in outlets 3 and 4 will receive 400Ws each.
Combination 1: one light in outlet 1 or 2 receives
600Ws; the second light in outlet 3 or 4 receives 300Ws.
Combination 2: in outlets 1 and 2 receive 600Ws each.
Combination 3: in outlets 3 and 4 will receive 300Ws each.
Following the above table will quickly illustrate other combinations that are possible with
up to four light units on the D1604.
Following the table above will quickly illustrate other combinations that are
possible with up to four light units on the D1204.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
D1204 Power Supply
TECHNICAL SPECIFICATIONS
Maximum power: . . . . . . . . . . . . . . . . . . . . .1200Ws
Number of light unit outlets: . . . . . . . . . . . .4
Recycle time:
(to 85% voltage, ANSI standard)
watt-seconds
seconds
4.1
2.0
D604 Power Supply
1200
600
300
Maximum power: . . . . . . . . . . . . . . . . . . . . .600Ws
Number of light unit outlets: . . . . . . . . . . . .4
1.0
Recycle time:
watt-seconds
(to 85% voltage, ANSI standard) . . . . . . . . . . . . .600
300
Flash duration . . . . . . . . . . . . . . . . . . . . . . . .1/590 sec. (1.7 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .600Ws
Minimum power into one light unit: . . . . . . .225Ws
Minimum power per light with 4 light units: .22.5Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 10 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.9 x 9.1" (foot print) x 5.9" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11.2 lbs.
seconds
2.3
1.3
Flash duration : . . . . . . . . . . . . . . . . . . . . . . .1/370 sec. (2.7 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .1200Ws
Minimum power into one light unit: . . . . . . .225Ws
Minimum power per light with 4 light units: .22.5Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 10 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.9 x 9.1" (foot print) x 7.9" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14.4 lbs
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Guide number : . . . . . . . . . . . . . . . . . . . . . . .455
(at ISO 100 w/M11Q fitted 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Guide number . . . . . . . . . . . . . . . . . . . . . . .250
(at ISO 100 w/M11Q fitted with 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
D1604 Power Supply
Maximum power: . . . . . . . . . . . . . . . . . . . . .1600Ws
Number of light unit outlets: . . . . . . . . . . . .4
Recycle time:
(to 85% voltage, ANSI standard)
watt-seconds
1600
seconds
6.0
800
2.8
400
1.3
Flash duration : . . . . . . . . . . . . . . . . . . . . . . .1/350 sec. (2.9 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .1600Ws
Minimum power into one light unit: . . . . . . .300Ws
Minimum power per light with
4 light units: . . . . . . . . . . . . . . . . . . . . . . . . . .30Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 10 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.4 x 9.5" (foot print) x 8.2" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16.2 lbs
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Guide number : . . . . . . . . . . . . . . . . . . . . . . .540
(at ISO 100 w/M11Q fitted 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Symmetrical/Asymmetrical
OPERATING INSTRUCTIONS
Power input
Model
Full/Half
Power
Operation of Brown Line power supplies is simple and straight forward. It is suggest-
ed that this sequence of operation be utilized for maximum life and dependability.
Make sure that the Model and Power switches are in the off position and the Push to
Reset buttons are fully depressed into their sockets. Connect light head cable(s) to the
Light Unit Outlet(s) on the power supply. The outlets are wired in parallel so it does not
matter in what sequence light head cables are connected.
Never connect or disconnect light units while power is on. Do not insert or remove
flash tubes while power is on. Your Brown Line power supply is equipped with
arc-protection, but should your light unit or power supply malfunction, or the power
cord, or even the internal wiring in the studio be improperly terminated or defective, the
chance of arc-over when connecting or disconnecting light units is greatly increased.
Severe power supply damage and operator injury may result if arc-over occurs when
light units are being disconnected or connected. To prevent this, you should always turn
the power supply off when disconnecting or connecting light heads.
Never subject a flash tube to more watt-seconds than it is designed to handle. MW3
and M90 series (non-”Q”) light units have a maximum rating of 400Ws, while “Q” ver-
sions are rated at 1200Ws. M11 light units are rated at 1200Ws* (with new MW9H
flashtube) and M11Q light units are rated at 2400Ws. We strongly recommend that at
least one light unit in your system is capable of handling the maximum output of your
power supply. If you are not sure if your flash tube and light unit can handle the power
provided by the set up you are using, check pages 25 and 26 and the Power Distribution
Chart on the side of your power supply.
Ready/Push to flash
Push to reset
Light unit outlets
Sync
DESCRIPTION OF CONTROLS
Power – turns power supply on and off (flashes units when turning off D802 or D402).
Model – turns model lamp(s) on and off.
Connect AC power cord into Power Input on power supply, then plug into a properly
grounded outlet. Use proper 3-conductor grounded cord for operator safety and to
reduce self-firing caused by static electricity. Set Full/Half switch as desired. This switch
reduces the total output of the power supply. The difference between the “full” and
“half” settings is one f-stop. After flashing, do not switch the Full/Half switch until ready
light is illuminated, or until at least ten seconds after turning off unit. Failure to follow
this procedure may result in damage to the switch.
Symmetrical/Asymmetrical – controls power distribution. In the symmetrical position,
power is split equally between all lights. In the asymmetrical position, power is
distributed unequally and model lamp brightness on light units in outlets 3 and 4 is
reduced.
Full/Half – controls amount of power delivered to light unit outlets.
Ready/Push to Flash – a combination ready light and test flash button. Illuminates to
indicate when power supply has recycled to 85%. Pressing the button when
illuminated triggers the flash for testing or open flash applications.
Sync – socket for sync extension or slave.
Plug sync connector into Sync socket and connect the other end to PC cord for camera.
Once the camera is connected, tripping the shutter will automatically trigger the flash.
Push to Reset – resets circuit breaker. Circuit breaker disables power supply in case of
malfunction.
Power Input – socket for AC power cord.
Light Unit Outlets (4) – sockets for connecting from one to four light units to power
supply.
A slave tripper (Speedotron #23510), may be inserted into the Sync socket in place of
the PC cord. In this mode of operation, the slave will activate the power supply when it
senses a bright flash of light from another light source. If the power supply fails to flash
when exposed to another light source with the slave installed in the sync socket, it may
be necessary to remove the slave, rotate it 180° and reinstall it into the Sync socket.
*New MW9H flashtubes supplied with M11 light units handle up to 1200Ws.
The MW9M flashtubes have a maximum capacity of 1000Ws.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn on Power and Model switches. Wait until the Ready/Push to Flash illuminates and
press the button to check if the unit is operational. The light unit(s) should flash instantly
when this button is pressed. If you wish to check the function of each individual light unit,
we recommend that you turn off the Model switch and hold your hand in front of (not
inside) the light unit to be tested. When you fire the unit you will feel the heat of the
flash. This method is suggested because it is often difficult to determine by sight if one
of the lights has failed to flash.
When disassembling the system or changing the position of a light unit connector in any
outlet, it is a good habit to set the Full/Half switch to full first, then turn off Model and
Power switches prior to disconnecting light units. If this procedure is not followed, allow
10 seconds between turning the Power switch off and adjusting the Full/Half switch.
DO NOT immediately switch to full power! Damage to the switch may result.
The D402 and D802B power supplies will flash their light units when turned off. Placing
the Full/Half switch on the D402 and D802B into the full position before turning off
Power will ensure that all capacitors are discharged.
One light:
Symmetrical mode in any outlet, will receive 400Ws.
Asymmetrical mode in outlets 1 or 2, will receive 400Ws;
when using outlets 3 or 4 output is 300Ws.
Two lights: Symmetrical mode, all outlets share an equal amount of power.
Two lights each receive 200Ws (400Ws divided by 2).
Asymmetrical mode
Combination 1: one light in outlet 1 or 2 receives 200Ws;
the second light in outlet 3 or 4 receives 100Ws.
Combination 2: in outlets 1 and 2 receive 200Ws each.
Combination 3: in outlets 3 and 4 will receive 100Ws each.
Following the table will quickly illustrate other combinations that are possible with
up to four light units on the D402.
D802B Power Distribution Table
POWER DISTRIBUTION TABLES
Symmetrical
Any socket(s)
Asymmetrical
1 or 2
3 or 4
On the side of the D202, D402 and D802B power supplies, there is a Power Distribution
Table based on the full power setting. These tables should be used as guides for deter-
mining various lighting possibilities, guide numbers and exposures when using consistent
flash tubes and reflectors. When different flash tubes and/or reflectors are used actual
light output will vary producing as much as a full f/stop discrepancy with the table.
The ’02 Series feature symmetrical and asymmetrical operation. Symmetrical output
means all light units share equal output. To determine power levels, divide the total
watt-seconds by the number of light units to be used. In asymmetrical mode, outlets 1
and 2 receive a greater portion of the total output than outlets 3 and 4. (For specific
power distribution refer to the charts below for the number and configuration of the
lights to be used.)
800
800Ws
400Ws
1 Light
600
200
400
2:1
2 Lights
400
400
1:1
200 200
1:1
400
100 100
140
4:1:1
2:2:1
3 Lights
4 Lights
266Ws
200Ws
280 280
240
240
60
60
4:4:1:1
D402 Power Distribution Table
Divide watt-seconds by 2 when using half power.
Symmetrical
Asymmetrical
Any socket(s)
1 or 2
3 or 4
One light:
Symmetrical mode in any outlet, will receive 800Ws.
Asymmetrical mode in outlets 1 or 2, will receive 800Ws;
when using outlets 3 or 4 output is 600Ws.
400
400Ws
200Ws
1 Light
300
100
Two lights: Symmetrical mode, all outlets share an equal amount of power.
200
2:1
Two lights each receive 400Ws (800Ws divided by 2).
2 Lights
200
200
1:1
Asymmetrical mode
100 100
1:1
Combination 1: one light in outlet 1 or 2 receives 400W;
the second light in outlet 3 or 4 receives 200Ws.
Combination 2: in outlets 1 and 2 receive 400Ws each.
Combination 3: in outlets 3 and 4 will receive 200Ws each.
200
50
50
4:1:1
2:2:1
3 Lights
4 Lights
133Ws
100Ws
140 140
70
Following the table will quickly illustrate other combinations that are possible with
up to four light units on the D802B.
120
120
30
30
4:4:1:1
Divide watt-seconds by 2 when using half power.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Symmetrical/Asymmetrical
Model
Light unit outlets
TECHNICAL SPECIFICATIONS
Power
D402 Power Supply
Maximum power: . . . . . . . . . . . . . . . . . . . . .400Ws
Number of light unit outlets: . . . . . . . . . . . .4
Recycle time:
(to 85% voltage, ANSI standard) . . . . . . . . . . . . .400
200
watt-seconds
seconds
1.75
0.9
Flash duration : . . . . . . . . . . . . . . . . . . . . . . .1/1200 sec. (.8 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .400Ws
Minimum power into one light unit: . . . . . . .150Ws
Minimum power per light with 4 light units: .15Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 10 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5 x 7.9" (foot print) x 7.2" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11.5 lbs
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Push to reset
Sync
Ready/Push to flash
Guide number : . . . . . . . . . . . . . . . . . . . . . . .270
(at ISO 100 w/M11Q fitted 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
DESCRIPTION OF CONTROLS
Power – turns power supply on and off. (Flashes light units when turning off.)
Model – turns model lamps on and off.
D802 Power Supply
Maximum power: . . . . . . . . . . . . . . . . . . . . .800Ws
Number of light unit outlets: . . . . . . . . . . . .4
Recycle time:
Symmetrical/Asymmetrical – controls power distribution. In the symmetrical position,
power is split equally between all lights. In the asymmetrical position power is
distributed unequally and the model lamp brightness/flash tube output of a light
in outlet #2 is reduced.
Ready/Push to Flash – a combination ready light and test flash button. Illuminates to
indicate when power supply has recycled to 85%. Pressing the button when
illuminated triggers the flash for testing or open flash applications.
Sync – socket for sync extension or slave.
watt-seconds
(to 85% voltage, ANSI standard) . . . . . . . . . . . . .800
400
Flash duration : . . . . . . . . . . . . . . . . . . . . . . .1/830 sec. (2.9 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .800Ws
Minimum power into one light unit: . . . . . . .150Ws
Minimum power per light with 4 light units: .30Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 10 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5 x 7.9" (foot print) x 7.2" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 lbs
seconds
3.2
2
Circuit Breaker/Reset – resets circuit breaker. Circuit breaker disables power supply in
case of malfunction. Does not affect model lamp circuit.
Light Unit Outlets (2) – sockets for connecting one or two light units to power supply.
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Guide number : . . . . . . . . . . . . . . . . . . . . . . .380
(at ISO 100 w/M11Q fitted 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
OPERATING INSTRUCTIONS
Make sure that the Model and Power switches are in the off position and the Push to
Reset button is fully depressed into its socket. Connect light head cable(s) to the Light
Unit Outlet(s) on the power supply. The outlets are wired in parallel so it does not mat-
ter in what sequence light head cables are connected.
D202 Power Supply
Maximum power: . . . . . . . . . . . . . . . . . . . . .200Ws
Number of light unit outlets: . . . . . . . . . . . .2
Recycle time:
(to 85% voltage, ANSI standard)
watt-seconds
200
seconds
3.25
Never connect or disconnect light units while power is on. Do not insert or remove
flash tubes while power is on. Your Brown Line power supply is equipped with arc-pro-
tection, but should your light unit or power supply malfunction, or the power cord, or
even the internal wiring in the studio be improperly terminated or defective, the chance
of arc-over when connecting or disconnecting light units is greatly increased. Severe
power supply damage and operator injury may result if arc-over occurs when light units
are being disconnected or connected. To prevent this, you should always turn the power
supply off when disconnecting or connecting light heads.
Flash duration . . . . . . . . . . . . . . . . . . . . . . . .1/1200 sec. (.85 milliseconds)
(at full power w/one M11Q light unit measured 1/2 to 1/2 peak as per ANSI PH3.40)
Maximum power into one light unit: . . . . . . .200Ws
Minimum power into one light unit: . . . . . . .150Ws
Minimum power per light with 2 light units: .50Ws
Power input requirements: . . . . . . . . . . . . . .105-120VAC 50-60Hz. 4 amps peak
Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.4 x 6.5" (foot print) x 6.2" (case height)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5 lbs.
System voltage: . . . . . . . . . . . . . . . . . . . . . . .900V
Trigger voltage: . . . . . . . . . . . . . . . . . . . . . . .70V
The D202 is fully compatible with all Speedotron Brown Line light units and flash
tubes.
Trigger current: . . . . . . . . . . . . . . . . . . . . . . .0.000043A (43 micro-amps)
Guide number . . . . . . . . . . . . . . . . . . . . . . .190
(at ISO 100 w/M11Q fitted with 11-1/2" reflector measured at 10 feet, on axis with MW9QC flash tube)
Connect power supply cord into a 3-wire grounded AC outlet. This reduces misfires and
self-firing caused by static electricity.
Plug sync connector into Sync socket and connect the other end to PC cord for
camera. Once the camera is connected, tripping the shutter will automatically trigger the
flash.
D202 Power Distribution Table
A slave tripper (Speedotron #23510), may be inserted into the Sync socket in place of
the PC cord. In this mode of operation, the slave will activate the power supply when it
senses a bright flash of light from another light source. If the power supply fails to flash
when exposed to another light source with the slave installed in the sync socket, it may
be necessary to remove the slave, rotate it 180° and reinstall it into the Sync socket.
Symmetrical
Any socket(s)
Asymmetrical
1 or 2 3 or 4
200
1 Light
200Ws
100Ws
150
50
Turn on Power and Model switches. Wait until the amber Ready/Push to Flash
illuminates and press the button to check if the unit is operational. The light unit(s)
should flash instantly when this button is pressed. If you wish to check the function of
each individual light unit, we recommend that you turn off the Model switch and hold
your hand in front of (not inside) the light unit to be tested. When you fire the unit you
will feel the heat of the flash. This method is suggested because it is often difficult to
determine by sight if one of the lights has failed to flash.
2 Lights
100
One light:
Symmetrical mode in any outlet, will receive 200Ws.
Asymmetrical mode: outlet 1 will receive 200Ws;
outlet 2 outputs 150Ws.
The D202 has symmetrical and asymmetrical power distribution. The two light units are
connected in parallel when the symmetrical/asymmetrical switch is in the symmetrical
position. With the switch in the asymmetrical position power will be distributed as shown
by the power distribution table on the next page or on the side of the power pack.
Two lights: Symmetrical mode, both outlets share an equal amount of power.
Two lights each receive 100Ws (200Ws divided by 2).
Asymmetrical mode: light in outlet 1 receives 100Ws;
the light in outlet 2 receives 50Ws.
Following the table will quickly illustrate other combinations that are possible with up
to four light units on the D202
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To connect light units, align the light unit plug with the power supply outlet and apply
even pressure while pushing. Black colored light unit connectors are of the “quick
release” type that only require pushing the connector firmly until it is fully seated. Silvery
colored light unit connectors must be threaded until they are fully seated. Both types
prevent accidental cable removal. Make sure all light unit cables are fimly seated to pre-
vent connector damage. Tape all cables to the floor and keep them out of the pathways
to prevent accidents.
BROWN LINE LIGHT UNITS
General Instructions and Information
The Speedotron Brown Line light units described here may be used with any Speedotron
Brown Line power supply using the five-pin MS outlet. All light units are supplied with a
20' wired-in cable.
Speedotron power supplies are equipped with arc-protected outlets. However, as with
any electrical equipment, arc-over (an electrical discharge between two physically dis-
connected electrical terminals) is a possibility. When light cables or flash tubes are
improperly seated, arc-over may occur. Also, if your light unit or power supply malfunc-
tions, or the power cord or the internal wiring in the studio is improperly terminated or
defective, there is a chance of arc-over when connecting or disconnecting light units.
Severe power supply damage and operator injury may result if arc-over occurs. That is
why, in spite of the arc-protection feature of Speedotron units, you should always make
sure Power is off when connecting or disconnecting light units.
Unpack and examine all equipment carefully. Should you notice any breakage or defect,
notify your dealer (and the carrier if it was shipped to you) immediately. The flash tube(s)
and model lamp(s) are packed in their original cartons. This affords sufficient protection
and reduces the incidence of breakage during shipping. Make sure all packing materials
are removed before using. This includes the pipe cleaners (used as packing material)
inside some flash tubes.
Install flash tubes first. Always handle lamps and flash tubes with care. Because they can
break if put under stress, handle them cautiously. Don’t touch glass surfaces with your bare
hands. If your fingers come in contact with the glass of the model lamp, wipe off carefully
with alcohol. When removing or replacing lamps and tubes, always disconnect light units
from power supply. Allow lamps to cool before handling. For instructions on how to insert
model lamps into specific units, see the unit descriptions on the following pages.
All Brown Line light units fit on top of 5/8" light stands. MW3U and MW3UCC accept
umbrellas with shafts up to 3/8". MW3R and MW3RCC light units include an adaptor to
fit onto 3/8" light stands.
Turn on power supply, wait for Ready light, then press Push to Flash button to verify
proper operation. The model lamp may be turned on or off by the switch located on the
top of the light unit assembly (insure that the Model switch at power supply is on).
Flash tubes must be inserted into the sockets all the way. Flash tube pins must align with
the flash tube socket to be inserted. Apply gentle pressure. A slight rocking motion may
be necessary when installing larger flash tubes. New flash tubes and sockets fit very
tightly. Be sure all flash tubes and model lamps are fully seated into light unit sockets.
For maximum performance and life, the model lamp should be used only when
necessary and turned off after initial set-up or focusing is done. Although convection
cooling is more than ample for normal usage, turning off the model lamp will eliminate
heat and enable the light unit to run cooler, extending the life of all components.
It is important to observe the maximum watt-seconds rating of these light units. Never
subject a flash tube to more watt-seconds than it is designed to handle. MW3 and
M90 series (non-”Q”) light units have a maximum rating of 400Ws, while “Q”
versions are rated at 1200Ws. M11 light units are rated at 1200Ws* (with new MW9H
flashtubes) and M11Q light units are rated at 2400Ws. We strongly recommend that at
least one light unit in your system should be capable of handling the maximum output of
your power supply. If you are not sure that the flash tube in your light unit can
handle the power provided by the set up you are using, check the following pages and
the Power Distribution Chart on the side of your power supply. Failure to observe this
precaution could drastically shorten the life of your flash tubes.
After extended use or after transporting your system, inspect flash tubes for cracks and
any unusual darkening (arc-over) around the tube sockets. If cracks or darkening are
noted the flash tube is, most likely, near the end of its duty cycle. Cracked tubes will
probably misfire. The normal duty cycle is 100,000 flashes for the majority of Speedotron
Brown Line flash tubes.
Be sure replacement flash tubes are designed for the watt-second output requirements
of Speedotron light units. Applying too much power severely shortens the life of flash
tubes, may cause fine cracks to develop in the tube that may cause tube failure or, in the
most extreme case, may cause the tube to shatter. For this reason, we suggest you
always use Speedotron flash tubes and model lamps to insure safe and dependable
operation.
Connect light cable(s) to the Light Unit Outlet(s) on the power supply. Never connect or
disconnect light units while Power is on. Do not insert or remove flash tubes or model
lamps while Power is on.
*New MW9H flashtubes supplied with M11 light units handle up to 1200Ws.
The MW9M flashtubes have a maximum capacity of 1000Ws.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
FIXED REFLECTOR LIGHT UNITS
Maximum power:
MW3 (for MW3R, MW3U, M90) . . . . . . . . . . . . . .400Ws
MW3C (for MW3R/CC, MW3U/CC, M90/CC) . . .400Ws
MW3Q (for MW3UQ, M90Q) . . . . . . . . . . . . . . . .1200Ws
MW3QC (for MW3UQ/CC, M90Q/CC) . . . . . . . .1200Ws
Flash duration (MW3 and MW3C):
at 400Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/830 sec.
at 200Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1300 sec.
Flash duration (MW3Q and MW3QC):
at 1200Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/500 sec.
at 800Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/600 sec.
at 600Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/830 sec.
at 400Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1200 sec.
Flash tube, standard . . . . . . . . . . . . . . . . . . . . . . . . . . .MW3 — 900V, 400Ws
Flash tube, 5500°K color corrected . . . . . . . . . . . . . . .MW3C — 900V, 400Ws
Flash tube, quartz standard . . . . . . . . . . . . . . . . . . . . .MW3Q — 900V, 1200Ws
Flash tube, quartz 5500°K color corrected . . . . . . . . . .MW3C — 900V, 1200Ws
Model lamp
MW3R and MW3R/CC
The MW3R series light units share a common base, but are differentiated by the type of
flash tube each contains. They feature 5-1/2" fixed reflector and are functional as back-
ground or hair lights. When installing flash tubes and model lights be sure that the unit is
disconnected from the power supply. To assemble, first insert the flash tube according to
the General Instructions, then insert the model lamp, using the packing material to hold
the lamp. The 60W candelabra base model lamp threads into the reflector-mounted
socket. The flash tubes are the MW3 (for MW3R) and MW3C (for MW3R/CC). Again, fol-
low the General Instructions to attach the light unit to the power supply. It accepts sever-
al accessories listed below including snoots, barn doors and diffusers. The MW3R con-
verts to the MW3R/CC by changing to the color corrected flash tube.
MW3U, MW3U/CC, MW3UQ and MW3UQ/CC
MW3U series light units share a common base, but are differentiated by the type of flash
tube each contains. They feature 5-1/2" fixed reflectors for use with umbrellas. When
installing flash tubes and model lamps be sure that the unit is disconnected from the
power supply. To assemble, first insert the flash tube according to the General
Instructions, then insert the model lamp, using the packing material to hold the lamp.
The 150W candelabra base model lamp inserts into the reflector-mounted socket. Align
the locking pins to the model lamp socket and use gentle pressure to insert and gently
twist the lamp 1/4 turn. The flash tubes are the MW3 (for MW3U), MW3C (for
MW3U/CC), MW3Q (for MW3UQ), and MW3QC (for MW3UQ/CC). Again, follow the
General Instructions to attach the light unit to the power supply. The light units accept
accessories listed below, including barn doors. It is recommended that snoots not be
used with the MW3U series because of heat from the model lamp.
MW3R series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60W candelabra base
MW3U series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150W quartz halogen
M90 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Three 25W locking base
ACCESSORIES FOR LIGHT UNITS
WITH FIXED REFLECTORS
M90, M90/CC, M90Q and M90Q/CC
14218
14216
25519
25526
25211
25213
24206
barn doors for 5.5" reflectors (2 leaf)
barn doors for 8.5" reflectors (2 leaf)
diffuser, 5.5” mylar clip-on
diffuser, 8.5” mylar clip-on
gel holder, 5.5”
gel holder. 8.5”
snoot for MW3R light unit, 2" opening; used to provide rim
lighting on hair and shoulders or other small objects.
snoot for MW3R light unit, 3" opening; used to provide rim
lighting on hair and shoulders or other small objects.
snoot for M90 light unit; used to provide rim lighting on hair
and shoulders or other small objects.
The M90 series light units share a common base, but are differentiated by the type of
flash tube each contains. They feature 8-1/2" fixed reflector light units for use with
umbrellas or as key and fill lights. When installing flash tubes and model lamps be sure
that the unit is disconnected from the power supply. To assemble, first insert the flash
tube according to the General Instructions, then insert the model lamps using the
packing material to hold the lamps. The three 25W model lamps insert into the reflector-
mounted sockets around the flash tube. Align the locking pins to the model lamp
sockets and use gentle pressure to insert and gently twist the lamp 1/4 turn. The flash
tubes are the MW3 (for M90), MW3C (for M90/CC), MW3Q (for M90Q), and MW3QC
(for M90Q/CC). Again, follow the General Instructions to attach the light unit to the
power supply. The light units accept several accessories listed below including snoots,
barn doors and diffusers.
24210
24213
25210
flood adapter for M90 light unit; increases angle of coverage to
110° when inserted between tube and socket.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
UNIVERSAL LIGHT UNITS (REMOVABLE REFLECTORS)
UNIVERSAL LIGHT ACCESSORIES
Reflectors
M11, M11/CC, M11Q and M11Q/CC
24226
24227
24235
24236
24219
14221
14209
grid reflector, 11.5” for M11 series light units
grid reflector, 16” - 50° for M11 series light units
grid reflector, 20” - 50° for M11 series light units
grid reflector, 22” for M11 series light units
reflector, 7” for M11 series light units
reflector for snoots, 7” black
The M11 series universal light units share a common base, but are differentiated by the
type of flash tube each contains. They are supplied with a removable 11-1/2" reflector
when purchased individually or include a 7" umbrella reflector when purchased in an
umbrella kit or flash systems. When installing flash tubes and model lamps be sure that
the unit is disconnected from the power supply. To assemble, first insert the flash tube
according to the General Instructions, then insert the model lamp, using the packing
material to hold the lamp. The 150W quartz model lamp inserts into the center of the
flash tube ring. Align the locking pins to the model lamp socket and use gentle pressure
to insert and gently twist the lamp 1/4 turn. The flash tubes are the MW9M (for M11),
MW9MC (for M11/CC), MW9Q (for M11Q), and MW9QC (for M11Q/CC). Again, follow
the General Instructions to attach the light unit to the power supply. Universal light units
accept a full range of quick-disconnect bayonet mount reflectors, snoots, barn doors,
diffusers and a tube protector.
snoot for 7” reflector, 2.5” opening
Barn doors
14217
14540
14542
24215
24501
24502
24503
24504
24505
Diffusers
24511
24512
24510
25525
25527
25528
25529
barn doors for 7" reflectors (2 leaf)
barn doors for 11.5" reflectors (2 leaf)
barn doors for 16" reflectors (2 leaf)
NEW! 4-way barn door system for 7” reflector
NEW! Cookaloris for 4-way system
NEW! Diffused Glass filter for 4-way system
NEW! Half Scrim for 4-way system
NEW! Graduated Scrim for 4-way system
NEW! Full Scrim for 4-way system
Technical Specifications
NEW! Lightsox diffuser for 11” reflector
NEW! Lightsox diffuser for 20/16” reflector
NEW! Lightsox diffuser for 22” reflector
diffuser, 7” mylar clip-on
diffuser, 11.5" mylar clip-on
diffuser, 16" mylar clip-on
Maximum power:
M11 and M11/CC . . . . . . . . . . . . . . . . . . . . . . . . .1200Ws
M11Q and M11Q/CC . . . . . . . . . . . . . . . . . . . . .2400Ws
Flash tubes:
M11, standard . . . . . . . . . . . . . . . . . . . . . . . . . . . .MW9H — 900V, 1200Ws
M11/CC, 5500°K color-corrected . . . . . . . . . . . . .MW9HC— 900V, 1200Ws
M11Q, quartz standard . . . . . . . . . . . . . . . . . . . . .MW9Q — 900V, 2400Ws
M11Q/CC, quartz 5500°K
diffuser, 20" mylar clip-on
Gel holders
25212
25214
25215
25216
gel holder, 7”
color corrected . . . . . . . . . . . . . . . . . . . . . . . . . . .MW9QC— 900V, 2400Ws
M11, M11/CC Flash duration
gel holder, 11.5”
gel holder, 16"
gel holder, 20"
at 800Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/740 sec.
at 600Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1100 sec.
at 400Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1500 sec.
at 200Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/250 sec.
M11Q, M11Q/CC Flash duration
at 1600Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/500 sec.
at 1200Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/625 sec.
at 800Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/830 sec.
at 600Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1000 sec.
at 300Ws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/1500 sec.
Model lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150W quartz halogen
Grids (for M11 & M11Q)
14611
14612
14613
14614
14615
14619
14601
14602
14603
14608
14621
14625
14630
grid, 7” - 3°
grid, 7” - 10°
grid, 7” - 20°
grid, 7” - 30°
grid, 7” - 40°
grids, set of four 7” (10°, 20°, 30°, 40°)
grid, 11.5” - 10°
grid, 11.5” - 20°
grid, 11.5” - 35°
grids, set of two 11.5” (20° & 35°)
grid, 16” - 20°
grid, 20” - 20°
grid, 22”
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING
GENERAL MAINTENANCE AND CARE
System will not work at all; no flash.
Check that sync cable, AC power cord and light unit cables are firmly and properly
attached. Check that the flash tube is firmly seated. Check that Power switch is on.
With metal camera bodies, you may be required to polarize the camera sync cable and
the power supply sync extension in order to avoid possible misfires resulting from a
build-up of static electricity. This is done by touching any unpainted metal part of the
power supply with the unpainted part of the camera, or better still, with the outer shell
or the grounded part of the sync cable with all sync cords attached. If the unit flashes,
the plug on the sync cable should be reversed and then marked for future reference.
Test fire the camera after reversing the sync extension cable (PC to power supply). If the
unit still does not fire, reverse the PC to camera connection and try again. The trigger
current is very low and is measured in microamperes, so it is impossible to even feel any
shock when touching these contacts.
All Speedotron Brown Line equipment is ruggedly built. Nevertheless, it should be
treated with the same care given to other pieces of quality photographic equip-
ment. To protect the user, all Speedotron equipment is designed to be safe when
used in accordance with instructions. To assure the maximum in safe, dependable
service, the following guidelines should be carefully observed.
• Avoid kinking or pulling cables. Disconnect cables by pulling on the plug only. Never
pull plugs out by the cable. Light cables as well as sync cords and AC power cords
should be occasionally checked for wear, cracks, separation between cable and plug, and
for indications of arc-over.
• Do not wrap the light unit cables around the light units. Coiling cables tightly stresses
the internal wires and may lead to premature cable failure. If possible, keep the coil
diameter at least 10 inches.
Occasional failure of all light units to flash.
Check sync cable and light unit cable connections. Make sure that the Ready indicator is
illuminated before attempting to fire unit.
• If a cable becomes frayed, the insulation damaged, or the connectors bent or broken,
have them repaired immediately.
Occasional failure of one light unit only.
Check light unit cable connection. Inspect the cable. Check flash tube. Make sure that
• Keep all connectors, plugs and sockets free of dust, moisture and corrosion.
the Ready/Push to Flash indicator is illuminated before attempting to fire unit.
• Do not connect or disconnect light units or insert or remove flash tubes while the
power supply is on.
Reduced light output.
Check to see if Full/Half/Low or Full/Half/1/4 switch is in right position. Check flash tube;
check power supply by comparing to similar pack with same light units if possible.
• When using your equipment, be sure all cable, sync, power and flash tube connections
are completely and properly installed.
Flash tube glows after firing (afterglow); will not flash again until glow is gone.
If confined to one light unit, check flash tube by substitution. If it continues or all heads
afterglow, power supply is at fault. If this is the case, turn power supply off immediately!
Power supply needs repair.
• Do not attempt to make repairs to your Speedotron equipment yourself. It is very
dangerous, and will void your warranty. Consult your dealer regarding authorized
service in your area, or return the equipment to Speedotron.
• When you are not using your equipment, it is recommended that you store it in a dry
place. Equipment should be charged up and flashed a few times at least once a month.
This will keep your equipment in top working condition for many years.
Full/Half/Low or Full/Half/1/4 switch has no effect on recycle time or light output.
Power supply needs repair.
Circuit breaker on power supply pops.
• With your light unit disconnected, occasionally clean the interior surface of the
reflector. Carefully remove the flash tube, and clean the glass cover. Only in this way will
you conserve a consistent color temperature and light output. Dirt and dust deposits on
the tube and reflector act like a filter to alter color.
Check that all cables on power supply and light units are properly connected. Also check
for afterglow. If a circuit breaker blows, it is an indication that something is wrong.
Normal operation will not blow circuit breakers.
Circuit breaker or fuse in studio blows.
Be sure AC line is rated for a minimum of 10 amperes and that high amperage
electrical equipment is not operating on the same AC line.
• Never handle the quartz halogen model lamps with your bare hands. Use tissue or
packing materials when installing and removing. The natural oils from your skin may
cause the glass surface to heat unevenly and cause early failure. When removing these
lamps allow sufficient cooling time before touching.
Important: When checking power supplies, light units and cables, be sure that Power is
off. Look for blackened, discolored or burned pins and sockets. If a Light Unit Outlet on
the power supply is burned, blackened or discolored, it must be replaced before it is
used. It could damage light units that are connected to it. Check that cables are not
loose or frayed.
• To extend their life, the model lamp circuit should be turned off after set-up and
focusing.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FLASH DURATION
GUIDE NUMBERS
Flash duration of a Speedotron Brown Line system will vary with the type of flash tube,
the amount of power outputted and the number of light units connected to the power
supply. For example, a D402 system with two M90 light units and two MW3R light units
will have four MW3-1 flash tubes and a 400Ws power supply. When set to full power
each flash tube will output 100 Ws with a flash duration of 1/1500 second.
Guide numbers provide a starting point in calculating the proper exposure for pictures
taken with flash. A guide number is a constant numerical value (for a given film
speed/ISO) determined by multiplying the light source-to-subject distance by the f-stop
in use on the lens. Consequently, dividing a given (known) guide number by the light
source-to-subject distance will yeld the proper f-stop. For example, if the given guide
number is 110 and the light source to subject distance is 10 feet, the f-stop required for
proper exposure is f/11.
Flash Duration in fractions of a second
Ws per flash tube
MW3-1
MW3Q
MW9H
MW9Q
The formula is as follows:
100Ws
200Ws
400Ws
600Ws
800Ws
1200Ws
1600Ws
1/1500
1/1200
1/750
1/1500
1/1200
1/750
1/580
1/450
1/330
-
1/3000
1/2200
1/1400
1/1000
1/700
1/500
-
1/3000
1/2200
1/1400
1/1000
1/700
guide number = G
light source-to-subject distance = D
f-stop = F
G = D x F
D = G/F
F = G/D
-
-
-
-
1/500
1/400
Important note: Guide number values provide a general starting point for exposure
determination and vary depending on a myriad of factors such as power supply differ-
ences, surrounding area reflectance, flash tube differences, etc. In some instances such
as extreme close-up and macro applications guide numbers will not provide accurate
exposure information. All guide numbers are approximations and we recommend that
test shots be produced to insure exposure accuracy.
Flash duration is measured from 1/2 peak light output to 1/2 light peak output as
illustrated below:
Peak
The guide numbers bellow are based on exposure from one light only, on axis with an
exposure index of ISO 100 in feet. The information supplied in the chart bellow is most
accurate for use in small, light colored rooms. For large or dark colored rooms it may be
necessary to open the lens 1/2 f-stop. For rooms which are both large and dark colored
it may be necessary to open up as much as one full f-stop.
1/2
0
flash duration
Light will continue to be produced for about five times the flash duration but will add
little to the exposure. This will not affect action stopping abilities for most normal
contrast subjects.
Guide Numbers at ISO 100/feet
Ws per flash tube
M90
M90 w/flood adapter
M11 w/7" reflector
M11 w/11" reflector
M11 w/16" reflector
M11 w/20" reflector
MW3R
MW3U w/o umbrella
100Ws
200Ws
400Ws
800Ws
1200Ws
1600Ws
123
175
245
320*
385*
-
80
115
160
220*
265*
-
68
95
135
190
230
270*
135
190
270
380
455
540*
105
150
210
295
355
420*
113
160
225
320
380
450
95
135
190
255*
305*
-
95
135
190
255*
305*
-
*use quartz flash tube only
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEEDOTRON’S LIMITED WARRANTY
Speedotron guarantees to repair or replace, free of charge, any part or parts (except for flash tubes
and modeling lamps) found by factory inspection to be defective due to faulty material or workman-
ship, provided the equipment is returned to our factory prepaid. The period of warranty is two years
from the date of original purchase. Flash tubes, which are warrantied by independent manufactur-
ers, are covered for a period of one year only, and the length of manufacturer warranties on model-
ing lamps varies. The manufacturers’ warranties covering flash tubes and modeling lamps are for
defective merchandise only, and do not cover tubes that are cracked or broken.
The Speedotron two-year warranty does not apply to equipment which has been abused, cracked
or broken in shipping, resold or rented (without written permission from Speedotron Corporation),
which has the serial number removed or defaced, which has been modified or repaired by an unau-
thorized person, or which has been purchased from any source other than an authorized
Speedotron dealer. A copy of the original sales receipt from an authorized Speedotron dealer is
required at the time of warranty service.
Speedotron shall not be liable for any injury, loss or damage, direct or consequential, arising from
the use or inability to use the product. Prior to use, the purchaser shall determine the suitability of
the product for the intended use and assume all risks and liabilities.
The obligation of Speedotron Corporation is limited to repair or replacement only and no one is
authorized to assume any obligation not in accordance with the above.
Do not attempt to make repairs to your Speedotron equipment. All electronic flash systems operate
on high voltage and high power. There is a high risk of severe electrical shock when opening a
power supply or light unit. Leave service to qualified and authorized electrical service personnel.
Authorized service personnel are familiar with the procedure to fully discharge a live unit (flashing
the unit is not enough to drain stored power even when the unit is unplugged). Repairs by unautho-
rized service personnel or by the user will void the Speedotron warranty.
Although we do have several service stations, we encourage you to send all repairs, under warranty
or otherwise, to our factory to ensure the best possible service. Not only will your unit be properly
repaired, but it will be given a routine updating of all circuitry that has been revised since your unit
was manufactured.
Should service be necessary under this warranty, return the item to us, prepaid (we do not accept
collect shipments). We, in turn, will expedite repairs and return the item to you, prepaid, via whatev-
er means of transportation you used to ship it to us (applies to continental U.S.A. only).
This warranty is not valid unless you fill out and return your warranty registration card. Equipment
should be registered within 10 days of purchase.
Speedotron Corporation
310 South Racine Avenue
Chicago, Illinois 60607
312/421-4050
Fax 312/421-5079
© 1997 Speedotron Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|