Notes on DualDiscs
WARNING
Basic Operations
A DualDisc is a two sided disc product which mates
DVD recorded material on one side with digital
audio material on the other side. However, since the
audio material side does not conform to the Compact
Disc (CD) standard, playback on this product is not
guaranteed.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
2-639-099-11(1)
To tune in a station with a weak signal
Press TUNING MODE
on the remote repeatedly
Adjusting the sound
until “MANUAL” appears, and then press +/– on the
remote repeatedly (or TUNING + or – on the unit)
tune in the desired station.
Micro HI-FI
to
To adjust the volume
Press VOLUME +/– on the remote (or turn the
Component System
Operating Instructions
Music discs encoded with
VOLUME control on the unit)
.
To reduce static noise on a weak FM stereo
station
copyright protection technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard. Recently,
various music discs encoded with copyright protection
technologies are marketed by some record companies.
Please be aware that among those discs, there are some
that do not conform to the CD standard and may not be
playable by this product.
To add a sound effect
To
GB
Press FM MODE
on the remote repeatedly until
“MONO” appears to turn off stereo reception.
Press
Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)
DSGX on the unit.
Playing a tape
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and
receiver.
–Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Set the sound effect
EQ on the remote.
Owner’s Record
Use buttons on the unit for the operation.
The model and serial numbers are located on the rear of the unit. Record these numbers in the space
provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. ______________ Serial No. ______________
1 Select a tape function.
Press FUNCTION repeatedly (or TAPE on the
NOTICE FOR CUSTOMERS IN THE
U.S.A.
remote)
.
Playing a CD/MP3 disc
1 Select the CD function.
2 Insert a tape.
Press (stop/eject)
tape into the cassette holder. Make sure there is no
slack in the tape to avoid damaging the tape or the
tape deck.
Printed on 100% recycled paper
using VOC (Volatile Organic
Compound)-free vegetable oil
based ink.
on the unit, and insert the
Open the tape
section lid.
Press CD on the remote (or FUNCTION repeatedly)
CMT-EH10/EH12LIV
.
2 Place a disc.
© 2005 Sony Corporation
Printed in China
Press PUSH OPEN/CLOSE on the unit, and place a
3 Start playback.
Press (play)
disc with the label side up on the CD compartment.
on the unit.
To close the CD compartment, press PUSH OPEN/
CLOSE on the unit.
CAUTION
Disposal of Old Electrical & Electronic
Equipment
(Applicable in the European Union
and other European countries with
separate collection systems)
To
Press
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
WARNING
Pause playback
(pause) on the unit. To
resume play, press it again.
PUSH OPEN/CLOSE
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
Stop playback
(stop/eject) on the unit.
NOTICE FOR CUSTOMERS IN
CANADA
Rewind or fast
forward*
/ on the unit.
This symbol on the product or on its packaging indicates
that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. The recycling of
materials will help to conserve natural resources. For
more detailed information about recycling of this
product, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
To reduce the risk of fire, do not cover the ventilation of
the apparatus with newspapers, tablecloths, curtains, etc.
And do not place lighted candles on the apparatus.
*Be sure to press (stop/eject)
been wound or rewound to the end.
on the unit after the tape has
CAUTION
The use of optical instruments with this product will
increase eye hazard.
Note
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
Do not turn off the system during playback or recording.
To reduce the risk of fire or electric shock, do not
place objects filled with liquids, such as vases, on the
apparatus.
3 Start playback.
Press (play)
the unit).
Except for European model
(or CD/ (play/pause)
on
accompanying the appliance.
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY STAR®
guidelines for energy efficiency.
Changing the display
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
CAUTION
To
Press
To change
Press
The use of optical instruments with this product will
increase eye hazard.
Pause playback
(pause) on the remote
This appliance is
Information on
the display1)
DISPLAY repeatedly when the
system is on.
(or CD/ on the unit). To
classified as a CLASS
1 LASER product. This
marking is located on the
rear exterior.
Applicable accessories: Remote commander
resume play, press it again.
Display mode
(Clock)
DISPLAY when the system is
off2). The clock is displayed for
eight seconds.
MPEG Layer-3 audio coding technology and patents
licensed from Fraunhofer IIS and Thomson.
Stop playback
(stop) .
Select a folder on an
MP3 disc
+/– .
1) For example, you can view CD/MP3 disc information, such as the
track or file number or folder name during normal play, or the total
play time while the player is stopped.
Before using the system
Select a track or file (go back/go forward)
on the remote ( on the
unit) .
2) The STANDBY indicator lights up when the system is turned off.
To use the remote
Slide and remove the battery compartment lid , and
insert the two R6 (size AA) batteries (not supplied),
side first, matching the polarities shown below.
Notes on the display information
• The following are not displayed correctly;
Find a point in a
track or file
Hold down / (rewind/fast
forward) during playback, and
release it at the desired point.
– total playing time for a disc with MP3 files.
– elapsed playing time and remaining time of an MP3 file encoded
using a VBR (variable bit rate) when the file is played or is shifted
with fast forward or fast reverse.
– folder and file names that do not follow either the ISO9660 Level
1 or 2 standard.
Hooking up the system securely
Select Repeat Play
REPEAT on the remote
repeatedly until “REP” appears.
• The following are displayed;
– ID3 tag information for MP3 files when ID3 version 1 and version
2 tags are used.
– up to 15 characters of ID3 tag information using uppercase letters
(A to Z), numbers (0 to 9), and symbols (‘< > * + , – / @ [ \ ] _).
To change the play mode
Press PLAY MODE
the player is stopped. You can select normal play (“
for all MP3 files in the folder on the disc), shuffle play
on the remote repeatedly while
Antennas
”
Keep the antennas away from the speaker cords to avoid
picking up noise.
(“SHUF” or “
SHUF*”), or program play (“PGM”).
*When playing a CD-DA disc,
operation as SHUF Play.
(SHUF) Play performs the same
Notes on using the remote
• With normal use, the batteries should last for about six months.
• Do not mix an old battery with a new one or mix different types of
batteries.
• If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.
Using optional audio
components
Notes on Repeat Play
• All tracks or files on a disc are played repeatedly up to five times.
• “REP1” indicates that a single track or file is repeated until you stop
it.
FM lead antenna
(Extend it horizontally.)
Power
To connect an optional headphones
To set the clock
Notes on playing MP3 discs
• Do not save other types of tracks or files or unnecessary folders on a
disc that has MP3 files.
• Folders that have no MP3 files are skipped.
• MP3 files are played back in the order that they are recorded onto
the disc.
• The system can only play MP3 files that have a file extension of
“.MP3”.
For models with a voltage selector, set VOLTAGE
SELECTOR to the local power line voltage.
Connect headphones to the PHONES jack
unit.
on the
1 Turn on the system.
Press (power)
.
To connect an optional component
Connect additional audio source components to the
Connect the power cord to a wall socket.
If the plug does not fit the wall socket, detach the
supplied plug adaptor (only for models equipped
with an adaptor).
2 Select the clock set mode.
Press CLOCK/TIMER SET
on the remote. If the
AUDIO IN jack
on the unit using an audio cord (not
current mode appears on the display, press /
supplied). Turn down the volume on the system, and then
select the AUDIO IN function.
• If there are files on the disc that have the “.MP3” file extension,
but that are not MP3 files, the unit may produce noise or may
malfunction.
on the remote repeatedly to select “CLOCK,” and
then press ENTER
on the remote.
• The maximum number of:
– folders is 150 (including the root folder).
– MP3 files is 255.
3 Set the time.
Press /
the hour, and then press ENTER
AM loop antenna
on the remote repeatedly to set
on the remote.
–
MP3 files and folders that can be contained on a single disc is 256.
– folder levels (the tree structure of files) is eight.
• Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.
Use the same procedure to set the minutes.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.
Insert only the stripped portion of the cord.
Notes on playing multisession discs
• If the disc begins with a CD-DA (or MP3) session, it is recognized
as a CD-DA (or MP3) disc, and playback continues until another
session is encountered.
• A disc with a mixed CD format is recognized as a CD-DA (audio)
disc.
Selecting a music source
Solid (Red/)
Press the following buttons (or press FUNCTION
repeatedly).
Left speaker
To select
Press
CD
CD on the remote.
TUNER/BAND .
Solid (Black/)
Listening to the radio
Tuner
Tape
Right speaker
TAPE on the remote.
1 Select “FM” or “AM.”
Press TUNER/BAND
Component* (connected
using an audio cord)
FUNCTION
repeatedly until “AUDIO
IN” appears.
repeatedly.
2 Select the tuning mode.
Press TUNING MODE
until “AUTO” appears.
on the remote repeatedly
*If the component has the AVLS (Automatic Volume Limiter System)
or BASS BOOST function, turn off the function to avoid distorted
sound from the speakers.
3 Tune in the desired station.
Press +/– on the remote (or TUNING + or – on
the unit) . Scanning stops automatically when a
Wall socket
station is tuned in. When you tune in a station that
provides RDS services, the station name appears on
the display.
Tip
To stop automatic scanning, press (stop)
.
Download from Www.Somanuals.com. All Manuals Search And Download.
|