4-249-347-15(3)
Multi-Channel
Integrated Amplifier
Operating Instructions
TA-DA9000ES
©2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1: Check how to hookup your
1a: Connecting components with
1b: Connecting components with
1c: Connecting components with only
5: Adjusting the speaker levels and
Specifications........................................ 53
List of button locations and reference
pages............................................... 56
Selecting the surround back decoding
Advanced Adjustments and
Switching the audio input mode for digital
3GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
1: Check how to hookup your components
connect each component.
Connectable components
Component to be connected
DVD player
Page
a)
With digital audio output
b)
With multi-channel audio output
c)
With analog audio output only
LD player
With digital audio output
a)
c)
With analog audio output
TV monitor
With component video input
With S-Video or composite video input only
Satellite tuner
With digital audio output
d)
a)
c)
With analog audio output only
VCR
a)
With digital audio output
c)
With analog audio output
CD/Super Audio CD player
With digital audio output
a)
b)
With multi-channel audio output
c)
With analog audio output only
MD/DAT deck
With digital audio output
a)
c)
With analog audio output only
Tape deck, Analog disc turntable, tuner
Multi-channel decoder
Video camera, video game, etc.
a)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
Model with MULTI CH OUTPUT jacks, etc. This connection is used to output the audio decoded by the
component’s internal multi-channel decoder through this amplifier.
b)
c)
d)
Model equipped only with AUDIO OUT L/R jacks, etc.
Model with component video (Y, P /C /B-Y, P /C /R-Y) input jacks.
B
B
R
R
4GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cords (A to I) (not supplied).
A Audio cord
F Coaxial digital cord
White (L)
Red (R)
G Monaural audio cord
B Audio/video cord
Black
Yellow (video)
White (L/audio)
Red (R/audio)
Tip
Audio cord A can be torn into two monaural audio
cords G.
C Video cord
Yellow
H Component video cord
Green
Blue
D S-video cord
Red
E Optical digital cord
I i.LINK cable
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the
components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
If you have Sony components with CONTROL A1II/CONTROL S
jacks
If you have Sony component (SCD-XA9000ES) with i.LINK jacks
Use the i.LINK cable (I) supplied with SCD-XA9000ES. For details, refer to the Operating
Instructions supplied with SCD-XA9000ES.
5GB
Download from Www.Somanuals.com. All Manuals Search And Download.
.
1a: Connecting components with digital audio output jacks
Hooking up a DVD player, LD player, VCR, TV monitor, or
satellite tuner
1 Connect the audio jacks.
LD player
VCR
OUTPUT
OUTPUT INPUT
AUDIO
OUT
LINE
LINE
OUTPUT
DIGITAL
OPTICAL
OUTPUT
DIGITAL
OPTICAL
OUTPUT
DIGITAL
COAXIAL
OUTPUT
DIGITAL
COAXIAL
L
L
OUT
IN
R
R
E*
F*
A
F*
E*
E
A
A
IN
OUT
IN
OUT
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
VIDEO
OUT
1
OUT
OUT
VIDEO
IN
OUT
OUT
IN
TAPE
IN
1
VIDEO
IN
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
P
R/CR/R-Y
P
R/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
E*
F*
F*
E*
A
A
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
DIGITAL
COAXIAL
DIGITAL
COAXIAL
DIGITAL
OPTICAL
DIGITAL
OPTICAL
AUDIO
OUT
AUDIO
OUT
L
L
R
R
DVD player**
Satellite tuner
* Connect to either the DVD COAXIAL IN or the DVD OPTICAL IN jack. We recommend making connections
to the DVD COAXIAL IN jack.
**To output the multi channel digital audio, set the digital audio output setting on the DVD player.
6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a TV or satellite tuner and a DVD player with
COMPONENT VIDEO (Y, P /C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component
B
B
R
R
video input jacks allows you to enjoy higher quality video. You can upconvert the video signals, and
Notes
• You can listen to the sound of your TV by connecting your TV’s audio output jacks to the TV/SAT AUDIO IN jacks on
the amplifier. In this case, do not connect the TV’s video output jack to the TV/SAT VIDEO IN jack on the amplifier.
• On this amplifier, standard video signals can be converted to component video and S-video signals, in addition S-
video signals can be converted to component video signals. However, you cannot convert component video signals
downward to standard video or S-video signals.
• When standard video signals (composite video signals) or S-video signals from a VCR etc. are converted upward
on this receiver and then output to your TV, depending on the status of the video signal output, the image on the
TV screen may appear distorted horizontally or no image may be output.
TV monitor
VCR
INPUT
VIDEO
INPUT
VIDEO
OUTPUT INPUT
VIDEO VIDEO
OUTPUT INPUT
OUTPUT
COMPONENT
B-Y
INPUT
COMPONENT
B-Y
R-Y
S
S
VIDEO
S
VIDEO
Y
Y
R-Y
C
C
D
D
H
H
D
C
IN
OUT
IN
OUT
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
VIDEO
OUT
1
OUT
TAPE
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
1
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
PR/CR/R-Y
P
R/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
TV/SAT
IN
CD/
SACD
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
DVI-D
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
MD/DAT
IN
4
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
SAT
TV/
SAT
2
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
H
C
D
C
D
H
OUTPUT
COMPONENT
B-Y
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
OUTPUT
COMPONENT
B-Y
R-Y
S
S
VIDEO
Y
Y
R-Y
DVD player
Satellite tuner
continued
7GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up a CD/Super Audio CD player or MD/DAT deck
CD/Super Audio
CD player
MD/DAT deck
OUTPUT
INPUT OUTPUT
AUDIO
OUT
LINE
LINE
DIGITAL
OUTPUT
DIGITAL
COAXIAL
OUTPUT
DIGITAL
OPTICAL
L
L
OPTICAL
IN
OUT
R
R
A
F* E*
E
E
A
A
OUT
IN OUT
IN
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
VIDEO
OUT
1
OUT
TAPE
IN
OUT
VIDEO
IN
OUT
OUT
1
VIDEO
IN
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
IN
PR/CR/R-Y
PR/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
OUT
VIDEO
IN
OUT
IN
VIDEO
IN
3
3
P
R/CR/R-Y
P
R/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
* Connect to either the CD/SACD COAXIAL IN or the CD/SACD OPTICAL IN jack. We recommend making
connections to the CD/SACD COAXIAL IN jack.
If you want to connect several digital components, but cannot find an
unused input
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies.
Notes
• No sound is output when playing a Super Audio CD disc on a Super Audio CD player connected to the CD/SACD
OPTICAL or CD/SACD COAXIAL IN jack on this amplifier. Connect the player to the analog input jacks (CD/
SACD IN jacks). Refer to the operating instructions supplied with the Super Audio CD player.
• You cannot make digital recordings of digital multi channel surround signals.
8GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1b: Connecting components with multi channel output
jacks
1 Connect the audio jacks.
If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect
it to this amplifier’s MULTI CHANNEL INPUT jacks to enjoy the multi channel sound. Alternatively,
the multi channel input jacks can be used to connect an external multi channel decoder.
MULTI CHANNEL OUT
DVD player,
FRONT
Super Audio CD
player,
SURR
OUND
Multi channel
decoder, etc.
SURR
BACK
CENTER
SUB
WOOFER
G
G
A
A
A
MULTI CHANNEL IN 1
MULTI CHANNEL IN 2
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
VIDEO
OUT
1
OUT
TAPE
IN
OUT
OUT
VIDEO
IN
OUT
IN
VIDEO
IN
1
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
PR/CR/R-Y
P
R/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
SURR
BACK
TV/SAT
IN
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
Tip
This connection also allows you to enjoy software with multi-channel audio recorded in formats other than the Dolby
Digital and DTS.
Note
DVD and Super Audio CD players do not have SURR BACK terminals.
continued
9GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a DVD player with COMPONENT VIDEO (Y, P /
B
C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component video input jacks allows you to
B
R
R
enjoy higher quality video. You can upconvert the video signals, and adjust the hue, etc. of the
Notes
• On this amplifier, standard video signals can be converted to component video and S-video signals, in addition S-
video signals can be converted to component video signals. However, you cannot convert component video signals
downward to standard video or S-video signals.
• When standard video signals (composite video signals) or S-video signals from a VCR etc. are converted upward
on this receiver and then output to your TV, depending on the status of the video signal output, the image on the
TV screen may appear distorted horizontally or no image may be output.
TV monitor
INPUT
VIDEO
INPUT
VIDEO
INPUT
COMPONENT
B-Y
S
Y
R-Y
H
D
C
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
VIDEO
OUT
1
OUT
TAPE
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
1
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
PR/CR/R-Y
PR/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
P
B/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
MULTI CHANNEL IN
SIGNAL
GND
H
C
D
OUTPUT
COMPONENT
B-Y
OUTPUT
VIDEO
OUTPUT
VIDEO
S
Y
R-Y
DVD player
10GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1c: Connecting components with only analog audio jacks
Hooking up audio components
OUTPUT
INPUT OUTPUT
INPUT OUTPUT
AUDIO
OUT
LINE
LINE
LINE
LINE
Tape deck
CD/Super Audio
CD player
MD/DAT deck
L
L
L
R
R
R
A
A
A
A
A
OUT
IN
OUT
IN
COMPONENT
VIDEO
AUDIO
VIDEO
L
DIGITAL
OPTICAL
DVD
IN
VIDEO
IN
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
Y
Y
VIDEO
1
OUT
TAPE
IN
OUT
OUT
VIDEO
IN
OUT
IN
OUT
VIDEO
IN
1
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
PR/CR/R-Y
P
R/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
A
A
OUTPUT
Turntable
LINE
L
Tuner
R
Note
If your turntable has a ground wire, connect it to the U SIGNAL GND terminal.
continued
11GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up video components
If you connect your TV to the MONITOR jacks, you can watch the video from the selected input
(page 22). You can also display the SPEAKER SET UP, LEVEL, SURR SET UP, EQUALIZER,
CUSTOMIZE menu settings and sound fields on your TV by pressing ON SCREEN on the remote.
VCR
INPUT OUTPUT
VIDEO
IN
VIDEO
OUT
Camcorderor
TV game
AUDIO
OUT
AUDIO
IN
INPUT OUTPUT
VIDEO VIDEO
L
S
S
R
B, D
B
B
D
D
OUT
IN OUT
IN
COMPONENT
VIDEO
AUDIO
VIDEO
DIGITAL
OPTICAL
DVD
IN
VIDEO
1
R
L
AUDIO
VIDEO
S2 VIDEO
R
L
Y
Y
IN
VIDEO
OUT
1
OUT
TAPE
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
1
1
PB/CB/B-Y
P
B/CB/B-Y
VIDEO
IN
1
P
R/CR/R-Y
P
R/CR/R-Y
LD
IN
OUT
OUT
OUT
OUT
IN
MD/DAT
VIDEO
2
VIDEO
2
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
DVD
IN
IN
IN
IN
PB/CB/B-Y
PB/CB/B-Y
CD/
SACD
IN
TV/SAT
IN
OUT
VIDEO
IN
OUT
VIDEO
IN
OUT
IN
3
3
P
R/CR/R-Y
PR/CR/R-Y
1
FRONT
MD/DAT
OUT
FRONT
VIDEO
VIDEO
4
4
MD/DAT
IN
SURR
OUND
IN
IN
IN
IN
IN
CONTROL A1II
SURROUND
LD
IN
LD
IN
CD/SACD
IN
SURR
BACK
CENTER
SURR BACK
COAXIAL
DVD
IN
DVD
IN
VIDEO
IN
1
SUB
WOOFER
CENTER
SUB WOOFER
TV/
TV/
2
SAT
SAT
LD
IN
IN
IN
IN
FRONT
AUDIO IN
PHONO
IN
To the
VIDEO 3
INPUT jacks
(Front panel)
PRE OUT
DVD
IN
i.LINK S200
SURR
OUND
MONITOR OUT
S2 VIDEO
VIDEO
TUNER
IN
OUT
1
OUT
1
TV/SAT
IN
SURR
BACK
R
L
CENTER
AUDIO
OUT
2
OUT
2
CD/SACD
IN
SUB
WOOFER
RS232C
SIGNAL
GND
MULTI CHANNEL IN
OUT
IN
OUT
IN
B
B
D
D
B
D
C
D
INPUT OUTPUT
INPUT
VIDEO
INPUT OUTPUT
OUTPUT
OUTPUT
INPUT
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
IN
VIDEO
OUT
VIDEO
OUT
AUDIO
OUT
AUDIO
OUT
AUDIO
IN
L
L
R
R
TV monitor
VCR
VCR
12GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Connecting speakers
Connect your speakers to the amplifier. This amplifier allows you to use a 9.1 channel system.
To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a
center speaker, and two surround speakers) and a sub woofer (5.1 channel).
You can enjoy high fidelity reproduction of DVD software recorded in the Surround EX format if you
connect one additional surround back speaker (6.1 channel) or two surround back speakers (7.1
You can even enjoy the 9.1 channel surround sound by connecting four surround speakers (see
Example of 7.1 channel speaker system configuration
Center speaker
Front speaker (R)
Surround speaker (R)
Front speaker (L)
Sub woofer
Surround speaker (L)
Surround back speaker (R)
Surround back speaker (L)
Tips
• When you connect 6.1 channel speaker system, place the surround back speaker behind the listening position.
• Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
Speaker impedance
To enjoy the best possible multi channel surround, connect speakers with a nominal impedance of 8
ohms or higher to the FRONT, CENTER, SURROUND and SURROUND BACK terminals, and set
the IMPEDANCE SELECTOR to “8Ω”. Refer to the operating instructions supplied with your
speakers if you are not sure of their impedance. (This information is often on the back of the speaker.)
Alternatively, you may connect speakers with nominal impedances between 4 and 8 ohms to any or all
of the speaker terminals. However, be sure to set the IMPEDANCE SELECTOR to “4Ω” if you
connect even one speaker with a nominal impedance between 4 and 8 ohms.
Note
Be sure to turn the power off before adjusting the IMPEDANCE SELECTOR.
continued
13GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
A Speaker cords (not supplied)
B Monaural audio cord (not supplied)
(+)
(–)
Black
Sub woofera)
Surround speaker
(L)
Center speaker
Surround speaker
(R)
INPUT
AUDIO
IN
e
e
E
e
E
E
A
A
A
B
SURROUND
SPEAKERS Bb)
COMPONENT
VIDEO
SPEAKERS
AC IN
DVD
IN
VIDEO
1
Y
Y
IN
SURROUND
R
L
P
B/CB/B-Y
PB/CB/B-Y
B
B
A
PR/CR/R-Y
PR/CR/R-Y
A
MONI
TOR
OUT
TV/
SAT
IN
Y
Y
P
B/CB/B-Y
P
B/CB/B-Y
CENTER
AC OUTLET
P
R/CR/R-Y
PR/CR/R-Y
SURROUND BACK
FRONT
R
L
SURROUND
SURR BACK
FRONT
CENTER
SUB WOOFER
R
L
B
A
B
A
PRE OUT
IMPEDANCE USE 4-16
A+B USE 8-16
FRONT
SPEAKERS Bc)
A
A
A
A
e
E e
E E
e
E
e
Surround back
speaker (L)d)
Surround back
speaker (R)d)
Front speaker (R)
Front speaker (L)
a)
b)
When you connect a sub woofer with an auto standby function, turn off the function when watching movies.
You can select the surround speakers you want to use with SPEAKERS SURROUND. For details, see “Selecting
c)
d)
You can select the front speakers you want to use with SPEAKERS FRONT. For details, see “Selecting the
If you connect only one surround back speaker, connect it to the SURROUND BACK SPEAKERS L terminal.
14GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip (Models of area code U, CA only)
To connect certain speakers to another power amplifier, use the PRE OUT jacks. The same signal is output from both
the SPEAKERS FRONT jacks and the PRE OUT jacks. For example, if you want to connect just the front speakers
to another amplifier, connect that amplifier to the PRE OUT FRONT L and R jacks.
Enjoying the 9.1 channel speaker system
What is the 9.1 channel speaker system?
A large dubbing theater for recording movie soundtracks uses 10 surround speakers. However, in a
small dubbing theater, only 2 speakers each are placed on the right, left, and back walls. Thus, the
minimum setup for a dubbing theater is 9.1 channels. When SPEAKERS SURROUND is set to A+B,
you can enjoy 9.1 channel speaker operation, just like a dubbing theater.
Arrange the speakers around the center
of the room based on the angles shown
in the illustration on the left. If you are
unable to position the speakers
according to the angles shown, place
one set of surround speakers slightly
forward of the listening position
(toward the front speakers).
Although the center of the room is used
as an axis for determining speaker
placement, 9.1 channel speaker
operation covers an extremely wide
listening area which you can enjoy
from anywhere in the room behind the
central point.
When using the CINEMA STUDIO EX modes with the 9.1 channel system, be sure to set Virtual
Speaker to OFF in SURR SET UP. (You can enjoy the surround effects of movies even without the use
of virtual speakers since so many real speakers are used.)
In addition, unlike virtual speakers, the expressive capability of real speakers will vary depending on
the speaker. Adjust the effect level so that the actor’s lines sound natural and the impact of sound effects
is nicely balanced.
The advantage of a 9.1 channel speaker system is a drastic improvement in the connection between the
front (video) sound field and the surround sound field. Previously, we have employed virtual speaker
technology to present this sound effect, but a real 9.1 channel multi channel surround system has a
much wider effect area so that all family members can enjoy the surround effect. Of course, when
seated in the middle of the listening position, you can enjoy the sound exactly as the movie director
listened.
Tips for placing speakers
Place surround speakers B between the front speakers and the listening position. Adjusting the position of these
speakers improves the connection between the front and surround sound stage.
continued
15GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips for using the 9.1 channel speaker system
You can also use the CINEMA STUDIO EX modes with the 9.1 channel speaker system. In this case, the number of
virtual surround speakers doubles (for a total of 12 virtual surround speakers).
However, this large number of speakers may narrow the surround effect area. Thus, it may be more effective to set
“VIR.SPEAKERS” in the SURR SET UP menu to “OFF”.
Please note that the front L/R and center speakers are common to all modes, and this function only changes the use
of the surround speakers. Depending on how you use SPEAKERS FRONT to switch the front speaker system (A/B),
and how you set “CENTER SP” in the SPEAKER SET UP menu (“YES” or “MIX”), you can set up two completely
different systems. For example, you can set up a 2 channel or 4 channel speaker system for pure audio sources, and
a 7.1 channel speaker system for AV sources.
Please note that in most cases you can use the 9.1 channel setting for Super Audio CD and other pure audio sources
without any adjustments. However, depending on the type of speakers you have and the way the music software was
recorded, you may want to switch to 7.1 channel or 5.1 channel playback. In such cases, you should set up your
surround speaker system to switch between A and B. Use surround speakers B for 5.1 channel operation and surround
speakers A+B for 9.1 channel operation.
16GB
Download from Www.Somanuals.com. All Manuals Search And Download.
connected component only while the amplifier is
turned on.
3: Connecting the AC
power cord
• Make sure that the total power consumption of the
component(s) connected to the amplifier’s AC
OUTLET(s) does not exceed the wattage stated on
the rear panel. Do not connect high-wattage
electrical home appliances such as electric irons,
fans, or TVs to this outlet. This may cause a
malfunction.
Connect the supplied AC power cord to the AC
IN terminal on the amplifier, then connect the
AC power cord to a wall outlet.
Performing initial setup
operations
AC power cord
Before using the amplifier for the first time,
initialize the amplifier by performing the
following procedure.
This procedure can also be used to return
settings you have made to their factory defaults.
AC OUTLET
1
2
Press ?/1 to turn off the amplifier.
Hold down ?/1 for 5 seconds.
“ENTER to Clear ALL” appears in the
display for 10 seconds.
SPEAKERS
AC IN
SURROUND
R
L
B
A
B
A
3
Press ENTER while “ENTER to Clear
ALL” appears in the display.
After “MEMORY CLEARING...” appears
in the display for a while, “MEMORY
CLEARED!” appears.
CENTER
AC OUTLET
The following are reset to their factory
settings.
SURROUND BACK
R
L
• All settings in the SPEAKER SET UP,
LEVEL, SURR SET UP, EQUALIZER,
and CUSTOMIZE menus.
FRONT
R
L
• The sound field memorized for each
input.
B
A
B
A
• All index names for inputs.
IMPEDANCE USE 4-16
A+B USE 8-16
AC IN
terminal
* The configuration, shape, and number of AC outlets
vary according to the area code.
Notes
• The AC OUTLET(s) on the rear of the amplifier is a
switched outlet, which supplies power to the
17GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTER to enter the selection. Check your
speaker pattern using the supplied “Easy Setup
Guide”.
4: Setting up the speakers
You can use the SPEAKER SET UP menu to set
the size and distance of the speakers connected
to this system.
x SUB WOOFER (Sub woofer)
• YES
If you connect a sub woofer, select “YES”.
• NO
1
2
Press ?/1 to turn on the system.
If you did not connect a sub woofer, select
“NO”. This activates the bass redirection
circuitry and outputs the LFE signals from
other speakers.
Rotate MAIN MENU to select
“SPEAKER SET UP”.
3
Rotate MENU to select the menu item
you want.
Tip
For more information, see “Speaker setup
In order to take full advantage of the Dolby Digital
bass redirection circuitry, we recommend setting the
sub woofer’s cut off frequency as high as possible.
Notes
• Certain setup parameters may be dimmed in the
display. This means that the selected parameter
is either unavailale or fixed and unchangeable
settings.
x FRONT SP (Front speakers)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
When the sub woofer is set to “NO”, front
speakers are automatically set to “LARGE”.
• SMALL
• Some speaker setup items may appear dimmed
in the display. This means that they have been
adjusted automatically due to other speaker
settings. Depending on the settings, you may or
may not be able to adjust certain speakers.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL”, the center, surround and surround
back speakers are also automatically set to
“SMALL” (unless previously set to “NO”).
4
5
Rotate –/+ to select the parameter.
all of the items that follow.
Note
Before setting up the surround speakers, select the
Speaker setup parameters
x CENTER SP (Center speaker)
The initial settings are underlined.
• LARGE
If you connect a large speaker that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the center speaker
to “LARGE”.
x SP EASY SET UP (Speaker easy setup)
• YES
You can set up your speakers automatically
by selecting a pre-defined speaker pattern (see
the supplied “Easy Setup Guide”).
• NO
• SMALL
Select to adjust the settings of each speaker
manually.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the front
speakers (if set to “LARGE”) or sub woofer.
x SPEAKER PATTERN
(Speaker setup pattern)
When “SP EASY SET UP” is set to “YES”,
select the speaker setup pattern. Rotate –/+ to
select the speaker setup pattern and press
18GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• NO or MIX
• SINGLE
If you did not connect a center speaker, select
“NO” or “MIX”. When set to “MIX”, the
sound of the center speaker can be output
from the front speakers without deteriorating
the sound quality. For details, see “MIX
SCALING” in the CUSTOMIZE menu
(page 37). The sound of the center channel
will be output from the front speakers.
When the multi channel input is selected,
analog downmixing is performed. Whether
the setting is “NO” or “MIX”.
If you connect only one surround back
speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
• NO
If you did not connect surround back
speakers, select “NO”.
Tip
The “LARGE” and “SMALL” settings for each
speaker determine whether or not the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
x SURROUND SP-A
(Surround speaker-A)
x SURROUND SP-B
(Surround speaker-B)
However, it best not to cut them, if possible. Therefore,
even when using small speakers, you can set them to
“LARGE” if you want to output the bass frequencies
from that speaker. On the other hand, if you are using
a large speaker, but prefer not to have bass frequencies
output from that speaker, set it to “SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the equalizer to boost the bass levels. To
The surround back speakers are set to the same
setting.
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the surround
speakers to “LARGE”.
x FRONT XXX meter
(Front speaker distance)
• SMALL
Initial setting: 3.0 meter
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
Lets you set the distance from your listening
position to the front speakers (A). You can
adjust from 1.0 meter to 7.0 meters in 0.1 meter
steps.
If both front speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
If you did not connect surround speakers,
select “NO”.
When placing only one surround back speaker
Tip
When the SPEAKERS SURROUND switch is set to
A+B, the settings for surround speaker-A are also set
for surround speaker-B.
A
A
30˚ 30˚
100˚-120˚
100˚-120˚
x SURR BACK SP
(Surround back speakers)
When the surround speakers are set to “NO”, the
surround back speakers are also automatically
set to “NO” and the setting cannot be changed.
• DUAL
If you connect two surround back speakers,
select “DUAL”. The sound will be output to a
maximum of 7.1 channels.
continued
19GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
When placing two surround back speakers
The amplifier lets you to input the speaker position in
terms of distance. However, it is not possible to set the
center speaker further than the front speakers. Also, the
center speaker cannot be set more that 1.5 meters
closer than the front speakers.
(The angle B should be the same)
A
A
30˚ 30˚
Likewise, the surround speakers can not be set farther
away from the listening position than the front
speakers. And they can be no more than 4.5 meters
closer.
100˚-120˚
100˚-120˚
B
B
B
This is because incorrect speaker placement is not
conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer
than the actual location of the speakers will cause a
delay in the output of the sound from that speaker. In
other words, the speaker will sound like it is farther
away.
x CENTER XXX meter
(Center speaker distance)
Initial setting: 3.0 meter
For example, setting the center speaker distance 1–2
meters closer than the actual speaker position will
create a fairly realistic sensation of being “inside” the
screen. If you cannot obtain a satisfactory surround
effect because the surround speakers are too close,
setting the surround speaker distance closer (shorter)
than the actual distance will create a larger sound stage.
Adjusting these parameter while listening to the sound
often results in much better surround sound. Give it a
try!
Lets you set the distance from your listening
position to the center speaker. You can adjust
from 1.0 meter to 7.0 meters in 0.1 meter steps.
x SURROUND-A XXX meter
(Surround speaker-A distance)
x SURROUND-B XXX meter
(Surround speaker-B distance)
Initial setting: 3.0 meter
Lets you set the distance from your listening
position to the surround speakers. You can
adjust from 1.0 meter to 7.0 meters in 0.1 meter
steps.
If both surround speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
For advanced speaker setups
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON”. This enables advanced
setups including surround speaker positioning.
For details on “MENU EXPAND”, see page 36.
x SURR BACK XXX meter
(Surround back speaker distance)
Initial setting: 3.0 meter
Lets you set the distance from your listening
position to the surround back speaker. You can
adjust from 1.0 meter to 7.0 meters in 0.1 meter
steps.
If you connect two surround back speakers and
both surround back speakers are not placed an
equal distance from your listening position, set
the distance to the closest speaker.
x SUB WOOFER XXX meter
(Sub woofer distance)
Initial setting: 3.0 meter
Lets you set the distance from your listening
position to the sub woofer. You can adjust from
1.0 meter to 7.0 meters in 0.1 meter steps.
20GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To output the test tone only from
a specific speaker
5: Adjusting the speaker
levels and balance
— TEST TONE
Set “TEST TONE” in the LEVEL menu to
from the selected speaker.
For more precise adjustment
Adjust the speaker levels and balance while
listening the test tone from your listening
position. Use the remote for these operations.
For details on remote operations, refer to the
operating instructions supplied with the remote.
You can output the test tone or sound source
from two adjacent speakers to adjust their
balance and level.
Set “MENU EXPAND” in the CUSTOMIZE
speakers you want to adjust using “PHASE
NOISE” or “PHASE AUDIO” in the LEVEL
Tip
The amplifier employs a test tone with a frequency
centered at 800 Hz.
1
2
3
Press ?/1 on the remote to turn on the
amplifier.
Press < on the remote repeatedly until
RECEIVER menu appears.
Move the easy scroll key to select
“TEST TONE”, then press the key to
enter the selection.
“TEST TONE” in the LEVEL menu
appears in the display and the test tone is
output from each speaker in sequence.
4
Adjust the speaker level and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu settings,
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/– on the remote or
turn MASTER VOLUME on the amplifier.
• You can also use TEST TONE on the amplifier
to turn on or off the test tone.
• You can also use –/+ on the amplifier for the
adjustment.
5
6
After the adjustment, press < on the
remote repeatedly again until amplifier
menu appears.
Move the easy scroll key to select
“TEST TONE”, then press the key
repeatedly to select “TEST TONE
[OFF]”.
The test tone turns off.
21GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To mute the sound
Press MUTING on the remote. To cancel, press
MUTING on the remote again or turn MASTER
VOLUME clockwise to raise the volume. Even
if you turn off the amplifier, the muting function
continues to mute the sound when you turn the
amplifier back on.
Amplifier Operation
Selecting the component
1
Rotate INPUT SELECTOR to select the
input.
The selected input appears in the display.
Note on using headphones
To select the
Display
When headphones are connected, you can select only
– HEADPHONE (2CH)
VCR
VIDEO 1, VIDEO 2,
VIDEO 3 or
– HEADPHONE (DIRECT)
VIDEO 4
– HEADPHONE (MULTI 1)
Camcorder or TV game VIDEO 5
– HEADPHONE (MULTI 2)
LD player
LD
– HEADPHONE THEATER
DVD player
Satellite tuner
Tape deck
DVD
TV/SAT
TAPE
MD/DAT
MD or DAT deck
CD or Super Audio CD CD/SACD
player
Tuner
TUNER
PHONO
i.LINK
Turntable
i.LINK component*
2
3
Turn on the component and start
playback.
Rotate MASTER VOLUME to adjust the
volume.
Note when “i.LINK” is selected
power of the i.LINK circuits turns on after “i.LINK” is
selected, and “i.LINK Connecting” appears in the
display while the power of the i.LINK circuits is
turning on. While this message appears, no sound is
output because LINC is not established. (See page 49
for details on LINC.)
Make sure to control the player after “i.LINK
Connecting” turns off.
The connected i.LINK component name appears
except in the following cases.
“No LINC” : No i.LINK component is connected when
“i.LINK” is selected.
“Disc”: The amplifier could obtain only general
information from the connected component.
“Unknown”: The amplifier could not obtain
information from the connected component.
22GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to multi channel
sound
Changing the display
Changing the information in
the display
— MULTI CH IN
You can select the audio directly from the
components connected to the MULTI
CHANNEL IN jacks. This enables you to enjoy
high quality analog inputs like DVD or Super
Audio CD.
You can check the sound field etc. by changing
the information in the display.
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display will
change as follows.
Index name* and sound field name y Input
name and sound field name
not activated when using this input.
Press MULTI CH IN 1/2 repeatedly to select
the multi channel audio source (“MULTI CH
1” or “MULTI CH IN 2”).
* Index name appears only when you have assigned
appear when only blank spaces have been entered, or
it is the same as the input name.
The selected audio source is output.
Note
This function is canceled when you select the sound
field indication by pressing MULTI CH IN 1/2, or
Displaying the input stream
information
When a center speaker or sub
woofer is not connected (Analog
downmix function)
You can check the input stream information
(about format, channel, etc.) of digital input
signals. The input stream information also
appears for 4 seconds when the amplifier detects
any changes in the digital input signal.
If you have set the center speaker to “NO” or
“MIX”, or set the sub woofer to “NO” in the
activate the MULTI CH IN function, the analog
center or sub woofer audio will be output from
the front left and right speakers.
1
2
Rotate MAIN MENU to select “STREAM
INFO”.
Rotate MENU.
The input stream information appears.
3
Rotate –/+ for more information.
Changing the brightness of
the display
Press DIMMER repeatedly.
The brightness of the display changes in 3 steps
(0% DOWN, 60% DOWN, 100% DOWN*).
* When 100% DOWN is selected, the indication
“100% DOWN” does not appear in the display.
23GB
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indications in the display
1
2
3 4 5 67
8
9
0
qa
qs
SW
L
C
R
INPUT AUTO I.LINK
COAX OPTANALOG MULTI CH IN 1 2
SLEEP
D.RANGE
RDS EQ
MEMORY
;
DIGITAL EX DTS-ES 96/24
PRO LOGIC II NEO:6 DISCRETE H.A.T.S.
MOVIE MUSIC CINEMA MATRIX STEREO MONO
SL
S
SR
L.F.E.
;
SBL
SB
SBR
qg
wf
wd ws
wa w; ql qk qj qh
qf qd
A SW: Lights up when sub woofer selection is
lights up, the amplifier creates a sub woofer
signal based on the LFE signal in the disc
being played back or the low frequency
components of the front channels. This
indicator does not light during the 2CH
STEREO mode or when 2 channel signal is
input while [A.F.D. AUTO] is selected and
[A.F.D. 2CH SW] in the SURR SET UP menu
is set to “OFF”.
D INPUT: Lights up constantly. One of the input
indicators also lights up according to the
current input.
E AUTO: Lights up when INPUT MODE is set
F i.LINK: Lights up when an i.LINK component
is connected.
G DTS (-ES): Lights up when DTS signals are
input. “-ES” lights up when DTS-ES signals
are input. When playing a DTS format disc, be
sure that you have made digital connections
and that INPUT MODE is NOT set to
B Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the amplifier downmixes the
source sound (based on the speakers settings).
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing)), SBL (Surround back
Left)*, SBR (Surround back right)*, SB
(Surround Back (the surround back
H COAX: Lights up when INPUT MODE is set
to “AUTO” and the source signal is a digital
signal being input through the COAXIAL
terminal, or when INPUT MODE is set to
I OPT: Lights up when INPUT MODE is set to
“AUTO” and the source signal is a digital
signal being input through the OPTICAL
terminal, or when INPUT MODE is set to
components obtained by 6.1 channel
decoding))
Example:
J ANALOG: Lights up when INPUT MODE is
set to “AUTO” and no digital signal is input to
COAXIAL or OPTICAL jack, or when
INPUT MODE is set to “ANALOG 2CH
Recording format (Front /Surround): 3/2.1
Output channel: Surround speakers absent
Sound Field: A.F.D. AUTO
SW
L
C
R
SL
SR
K MULTI CH IN 1/2: Lights up when “MULTI
CH IN 1” or “MULTI CH IN 2” is selected.
* Lights up when the test tone for SBL or SBR
signal is output.
L SLEEP: Lights up when sleep timer is
activated.
C ; DIGITAL (EX): Lights up when Dolby
Digital signals are input. “EX” lights up when
Dolby Digital EX signals are input.
M D.RANGE: Lights up when dynamic range
N EQ: Lights up when the equalizer is activated.
24GB
Download from Www.Somanuals.com. All Manuals Search And Download.
O H.A.T.S.: Lights up when the connected
i.LINK component is compatible with the
H.A.T.S. function.
P 96/24: Lights up when the amplifier is
decoding DTS 96 kHz/24 bit signals.
Q MATRIX: Lights up when DTS-ES Matrix
decoding is activated.
R DISCRETE: Lights up when DTS-ES
Discrete decoding is activated.
S CINEMA: Lights up when DTS Neo:6
Cinema decoding is activated.
T NEO:6: Lights up when DTS Neo:6 Cinema/
Music decoding is activated.
U MUSIC: Lights up when Pro Logic II Music
or DTS Neo:6 Music decoding is activated.
V MOVIE: Lights up when Pro Logic II Movie
decoding is activated.
W ; PRO LOGIC (II): Lights up when the
amplifier applies Pro Logic processing to 2
channel signals in order to output the center
and surround channel signals. This indicator
also lights when the Pro Logic II Movie/Music
decoder is activated. However, this indicator
does not light if both the center and surround
speakers are set to “NO”.
X L.F.E.: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel. When the sound of the LFE
channel signal is actually being reproduced,
the bars underneath the letters lights up to
indicate the level. Since the LFE signal is not
recorded in all parts of the input signal the bar
indication will fluctuate (and may turn off)
during playback.
25GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying higher fidelity
sound
Enjoying Surround Sound
Using only the front
speakers
— AUTO FORMAT DIRECT
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
In this mode, the amplifier outputs the sound
from the front L/R speakers only. There is no
sound from the sub woofer.
A.F.D. mode
Decoding mode
As encoded
AUTO
PRO LOGIC
Dolby Pro Logic
Listening to 2 channel stereo
sources (2CH STEREO)
PRO LOGIC II MOVIE
PRO LOGIC II MUSIC
Neo:6 Cinema
Neo:6 Music
Dolby Pro Logic II
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
DTS Neo:6
Multi Stereo
Multi Stereo
Press 2CH.
Decoding the input audio
signal automatically
“2CH STEREO” appears in the display and the
amplifier switches to the 2CH STEREO mode.
Note
In this mode, the amplifier automatically detects
the type of audio signal being input (Dolby
Digital, DTS, standard 2 channel stereo, etc.)
and performs the proper decoding if necessary.
This mode presents the sound as it was recorded/
encoded, without adding any surround effects.
However, when “A.F.D. 2CH SW” in the SURR
SET UP menu is set to “CREATE” and if there
are no low frequency signals (Dolby Digital
LFE, etc.) it will generate a low frequency signal
for output to the sub woofer.
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to the 2 channel stereo
sources using the front L/R speakers and a sub woofer,
select “A.F.D. AUTO” and set “A.F.D. 2CH SW” in
the SURR SET UP menu to “CREATE”.
Press A.F.D. repeatedly to select “A.F.D.
AUTO”.
The amplifier automatically detects the type of
audio signal being input and performs the proper
decoding if necessary.
Tip
In most cases, “A.F.D. AUTO” provides the most
appropriate decoding. You may want to use SURR
stream to the mode you prefer.
26GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying stereo sound in multi
channel (2 channel decoding
mode)
Selecting a sound field
You can take advantage of surround sound
simply by selecting one of the amplifier’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
This mode lets you specify the type of decoding
for 2 channel audio sources. This amplifier can
reproduce 2 channel sound in 5 channels
through Dolby Pro Logic II; 6 channels through
DTS Neo:6; or 4 channels through Dolby Pro
Logic. However, DTS 2CH sources are not
decoded by DTS Neo:6; they are output in 2
channels. When the multi channel signal are
input, the encoded multi channel signals are
output as they are.
Selecting a sound field for
movies
Press MOVIE repeatedly to select the
sound field you want.
The selected sound field appears in the display.
Press A.F.D. repeatedly to select the 2
channel decoding mode.
Sound field
CINEMA STUDIO EX A DCS
CINEMA STUDIO EX B DCS
CINEMA STUDIO EX C DCS
V.MULTI DIMENSION DCS
x PRO LOGIC
Performs Dolby Pro Logic decoding. The source
recorded in 2 channel is decoded into 4 channels.
x PRO LOGIC II MOVIE
Performs Dolby Pro Logic II Movie mode decoding.
This setting is ideal for movies encoded in Dolby
Surround. In Addition, this mode can reproduce sound
in 5.1 channel when watching videos of overdubbed or
old movies.
About DCS (Digital Cinema
Sound)
Sound fields marked DCS use DCS
technology.
x PRO LOGIC II MUSIC
DCS is the concept name of the surround
technology for home theater developed by Sony.
DCS uses the DSP (Digital Signal Processor)
technology to reproduce the sound
characteristics of an actual cinema cutting studio
in Hollywood.
Performs the Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal stereo
sources such as CDs.
x Neo:6 Cinema
Performs the DTS Neo:6 Cinema mode decoding.
When played at home, DCS will create a
powerful theater effect that mimics the artistic
combination of sound and action as envisioned
by the movie director.
When a sound field with the DCS mark is
selected, Digital Cinema Sound indicator lights
up.
x Neo:6 Music
Performs the DTS Neo:6 Music mode decoding. This
setting is ideal for normal stereo sources such as CDs.
x MULTI STEREO
Outputs the 2 channel L/R signals from all speakers.
If you connect a sub woofer
When the source signal does not include a LFE
signal, the amplifier generates a low frequency
signal for output to the sub woofer. However the
low frequency signal is not generated for “Neo:6
Cinema” or “Neo:6 Music” when all speakers
are set to “LARGE”.
x CINEMA STUDIO EX A DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Cary Grant Theater” cinema
production studio. This is a standard mode, great for
watching most any type of movies.
x CINEMA STUDIO EX B DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Kim Novak Theater” cinema
production studio. This mode is ideal for watching
continued
27GB
Download from Www.Somanuals.com. All Manuals Search And Download.
science-fiction or action movies with lots of sound
effects.
The selected sound field appears in the display.
Sound field
x CINEMA STUDIO EX C DCS
D.CONCERT HALL A
D.CONCERT HALL B
CHURCH
Reproduces the sound characteristics of the Sony
Pictures Entertainment scoring stage. This mode is
ideal for watching musicals or films where orchestra
music is featured in the soundtrack.
JAZZ CLUB
x V.MULTI DIMENSION DCS
Creates 5 sets of virtual speakers from a single pair of
actual surround speakers.
LIVE CONCERT
STADIUM
SPORTS
About CINEMA STUDIO EX modes
x D.CONCERT HALL A
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in your
home.
Uses 3D sound imaging to reproduce the sound
characteristics of the CONCERTGEBOUW in
Amsterdam, which is famous for a large sound stage
produced by reflectivity.
x D.CONCERT HALL B
Uses 3D sound imaging to reproduce the sound
characteristics of the MUSIKVEREIN in Vienna,
which is famous for its hall resonance and unique
reverberative sound.
The CINEMA STUDIO EX modes consist of
the following three elements.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a single
pair of actual surround speakers.
x CHURCH
Reproduces the acoustics of a stone church.
• Screen Depth Matching
x JAZZ CLUB
Creates the sensation that the sound is coming
from inside the screen like in theaters.
• Cinema Studio Reverberation
Reproduces the acoustics of a jazz club.
x LIVE CONCERT
Reproduces the acoustics of a 300-seat live house.
Reproduces the type of reverberation found in
theaters.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
x STADIUM
Reproduces the feeling of a large open-air stadium.
x SPORTS
Reproduces the feeling of sports broadcasting.
Tips
You can identify the encoding format of DVD
software, etc. by looking at the logo on the package.
When the headphones are
connected
–
–
–
: Dolby Digital discs
: Dolby Surround encoded programs
: DTS Digital Surround encoded programs
You can select only from the following sound
fields.
x HEADPHONE (2CH)
Notes
Press 2CH or A.F.D. Outputs the sound in 2 channel
(stereo). Standard 2 channel stereo sources completely
bypass the sound field processing and multi channel
surround formats are downmixed to 2 channels.
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
x HEADPHONE (DIRECT)
Press DIRECT. Outputs the analog signals without
digital processing by the equalizer.
Selecting a sound field for
music
x HEADPHONE (MULTI 1/MULTI 2)
Press MULTI CH 1/2. Outputs the analog signals input
to the MULTI CHANNEL INPUT jacks by
downmixing to 2 channels.
Press MUSIC repeatedly to select the
sound field you want.
28GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x HEADPHONE THEATER DCS
Press MOVIE or MUSIC. Allows you to experience a
theater-like environment while listening through a pair
of headphones.
Selecting the surround
back decoding mode
— SURR BACK DECODING
To turn off the surround effect
Press 2CH, or press A.F.D. to select “A.F.D.
AUTO”.
This function lets you select the decoding mode
for the surround back signals of the multi
channel input stream.
Enjoying the surround effect
at low volume level
(NIGHT MODE)
By decoding the surround back signal of DVD
software (etc.) recorded in Dolby Digital EX,
DTS-ES Matrix, DTS-ES Discrete 6.1, etc.
format, you can enjoy the surround sound
intended by the filmmakers.
This function allows you to retain a theater like
environment at low volume levels. This function
can be used with other sound fields.
When watching a movie late at night, you will be
able to hear the dialog clearly even at a low
volume level.
Press SURR BACK DECODING repeatedly
to select the surround back decoding
mode.
For details, see “How to select the surround back
Press NIGHT MODE.
Tip
The NIGHT MODE function is activated.
You can select the surround back decoding mode using
“SB DECODING” in the CUSTOMIZE menu
Tip
While this function is on, the BASS, TREBLE, and
EFFECT level increase, and “D.RANGE COMP.” is
Note
This function cannot be activated when the DIRECT
function is activated.
Listening to the sound
without any adjustment
You can listen to the sound without adjusting the
equalizer and surround effect.
Press DIRECT.
The equalizer and sound fields are canceled.
Note
input is selected and the DIRECT function is used.
continued
29GB
Download from Www.Somanuals.com. All Manuals Search And Download.
How to select the surround back decoding mode
You can select the surround back mode you want according to the input stream.
When you select “AUTO”
a)
When the input stream contains the 6.1 channel decode flag , the appropriate decoder is applied to
decode the surround back signal.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
e)
5.1
—
b)
e)
6.1
Matrix decoder for Dolby Digital EX
—
e)
5.1
c)
e)
DTS-ES Matrix 6.1
6.1
DTS Matrix decoder
DTS Discrete decoder
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “MATRIX”
Dolby Digital EX is applied to decode the surround back signal regardless of the 6.1 channel decode
a)
flag in the input stream. This decoder conforms to the Dolby Digital EX specifications and functions
f)
the same as the decoders used in movie theaters.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
Matrix decoder for Dolby Digital EX
Matrix decoder for Dolby Digital EX
Matrix decoder for Dolby Digital EX
Matrix decoder for Dolby Digital EX
Matrix decoder for Dolby Digital EX
e)
6.1
b)
e)
6.1
e)
6.1
c)
e)
DTS-ES Matrix 6.1
6.1
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “OFF”
Surround back decoding is not performed.
The SB DEC indicator lights up when the surround back signal is actually decoded.
a)
6.1 channel decode flag is the information recorded in software like DVDs.
b)
Dolby Digital DVD software that includes a Surround EX flag. The Dolby Corporation web page can help you
distinguish Surround EX films.
c)
Software encoded with a flag to denote it has both Surround EX and 5.1 channel signals.
d)
Software encoded with both 5.1 channel signals and an extension stream designed for returning those signals to
6.1 discrete channels. Discrete 6.1 channel signals are DVD specific signals not used in movie theaters.
e)
When two surround back speakers are connected, the output channel will be 7.1 channels.
f)
This decoder can be used for all 6.1 formats (Dolby Digital EX, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1).
Note
There may be no sound from the surround back speaker in Dolby Digital EX mode. Some discs have no Dolby Digital
EX flag even though the packages have Dolby Digital EX logos. In this case, select “MATRIX”.
30GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectable inputs for each digital
audio input
Advanced Adjustments and Settings
VIDEO 1 COAX, VIDEO 1 OPT
VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
Assigning the audio input
— DIGITAL ASSIGN
VIDEO 5 OPT
VIDEO 5, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
You can assign the digital audio inputs to other
inputs. This function is convenient in the
following cases.
DVD COAX, DVD OPT
DVD, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
(Example) When you have two DVD players
and no digital audio input jack is available
for the second DVD player.
LD COAX, LD OPT, LD DD RF
LD, VIDEO 2, VIDEO 3, VIDEO 4, TAPE, TUNER
TV/SAT COAX, TV/SAT OPT
Connect the first DVD player to the DVD
COAXIAL IN jack and connect the second
DVD player to the DVD OPTICAL IN jack.
Also, connect the analog audio/video output
jacks on the second DVD player to the VIDEO
2 INPUT jacks on the amplifier.
TV/SAT, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
MD/DAT OPT
MD/DAT, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
Assign “DVD COAX” to DVD and assign
“DVD OPT” to VIDEO 2.
CD/SACD COAX, CD/SACD OPT
CD/SACD, VIDEO 2, VIDEO 3, VIDEO 4, TAPE,
TUNER
1
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
Notes
Rotate MENU to select “DIGITAL
ASSIGN ?”.
• You cannot assign several digital audio inputs to the
same input.
3
4
Press ENTER.
• You cannot use the digital audio input with its the
original input when it is assigned to another input.
• When you assign the digital audio input, the INPUT
Rotate MENU to select the digital audio
input you want to assign.
5
Rotate –/+ to select the input you want
to assign the digital audio input jack
selected in step 4.
The input you can assign varies for each
audio input. For details, see “Selectable
31GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the audio input
mode for digital
components
Customizing sound fields
By adjusting the SURR SET UP menu and
LEVEL menu, you can customize the sound
fields to suit your particular listening situation.
— INPUT MODE
Note on the displayed items
The setup items you can adjust in each menu
vary depending on the sound field. Certain setup
parameters may be dimmed in the display. This
means that the selected parameter is either
unavailable or fixed and unchangeable.
You can switch the audio input mode for
components for which this amplifier has digital
audio input jacks.
1
2
Rotate INPUT SELECTOR to select the
input.
Press INPUT MODE repeatedly to
select the audio input mode.
Adjusting the SURR SET UP
menu
The selected audio input mode appears in
the display.
You can customize the surround effects of the
selected sound field. The settings are stored
individually for each sound field.
Audio input modes
• AUTO 2CH
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Gives priority to the digital audio signals
input to the DIGITAL COAXIAL jack,
DIGITAL OPTICAL jack, and to the AUDIO
IN (L/R) jacks in that order. When there are
no digital audio signals, the analog audio
signals input to the AUDIO IN (L/R) jacks are
selected.
2
3
Rotate MAIN MENU to select “SURR
SET UP”.
Rotate MENU to select the parameter.
For details, see “SURR SET UP menu
parameters” below.
• COAXIAL FIXED
Specifies the digital audio signals input to the
DIGITAL COAXIAL jack.
4
5
While monitoring the sound, rotate –/+
to adjust the selected parameter.
• OPTICAL FIXED
Specifies the digital audio signals input to the
DIGITAL OPTICAL jack.
parameters.
• ANALOG 2CH FIXED
SURR SET UP menu parameters
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
x EFFECT LEVEL XXX%
(Effect level)
Notes
Initial setting: 100%
• You cannot select the digital audio input assigned to
another function with the DIGITAL ASSIGN
Higher settings apply more surround effect.You can
adjust from 20% to 120% in 5% steps.
• Some of the audio input modes do not appear
depending on the input.
For advanced SURR SET UP
menu adjustments
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON” to enable advanced
adjustments.
For details on “MENU EXPAND”, see page 36.
32GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x MULTI CH 1 SW XXX dB
(Multi channel 1 sub woofer level)
Adjusting the LEVEL menu
x MULTI CH 2 SW XXX dB
(Multi channel 2 sub woofer level)
You can adjust the balance and level of each
speaker. These settings are applied to all sound
fields.
Initial setting: 0 dB
Lets you increase the level of the MULTI CHANNEL
INPUT 1/MULTI CHANNEL INPUT 2 sub woofer
channel by +10 dB. This adjustment may be necessary
when connecting a DVD player to the MULTI
CHANNEL INPUT 1/MULTI CHANNEL INPUT 2
jacks. The sub woofer level from DVD players is 10 dB
lower than Super Audio CD players.
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
2
3
Rotate MAIN MENU to select “LEVEL”.
Rotate MENU to select the parameter.
For details, see “LEVEL menu parameters”
below.
* Only when the surround back speaker is set to
“SINGLE” in the SPEAKER SET UP menu
4
5
While monitoring the sound, rotate –/+
to adjust the selected parameter.
**Only when the surround back speaker is set to
“DUAL” in the SPEAKER SET UP menu
parameters.
Note
When one of the following sound fields are selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” in the SPEAKER SET
UP menu. However, the sound will be output from the
sub woofer if the digital input signal contains LFE
(Low Frequency Effect) signals, or if the front or
surround speakers are set to “SMALL”.
– D.CONCERT HALL A
LEVEL menu parameters
x TEST TONE (Test Tone)
Initial setting: OFF
Lets you output the test tone sequentially from each
speaker. When set to “AUTO”, the test tone is output
from each speaker automatically. When set to “FIX”,
you can select which speaker will output the test tone.
– D.CONCERT HALL B
x FRONT L_I_R (Front speaker balance)
Initial setting: 0 (BALANCE)
– CHURCH
– JAZZ CLUB
Lets you adjust the balance between front left and right
speakers. You can adjust from –8 dB to +8 dB in 0.5
dB steps.
– LIVE CONCERT
– STADIUM
– SPORTS
x CENTER XXX.X dB
(Center speaker level)
For advanced LEVEL menu
adjustments
x SURROUND L XXX.X dB
(Surround speaker (L) level)
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON” to enable advanced
adjustments.
x SURROUND R XXX.X dB
(Surround speaker (R) level)
x SURR BACK XXX.X dB
(Surround back speaker level)*
x SURR BACK L XXX.X dB
(Surround back (L) level)**
x SURR BACK R XXX.X dB
(Surround back (R) level)**
Resetting sound fields to the
initial settings
x SUB WOOFER XXX.X dB
(Sub woofer level)
1
2
Press ?/1 to turn off the power.
Initial setting: 0 dB
While holding down MUSIC, press
?/1.
You can adjust from –20 dB to +10 dB in 0.5 dB steps.
continued
Download from Www.Somanuals.com. All Manuals Search And Download.
33GB
“S.F. Initialize” appears in the display and
all sound fields are reset to the initial
setting.
Adjusting the equalizer
You can adjust the tonal quality (bass, midrange,
treble level) of each speaker using the
EQUALIZER menu.
Midrange
Bass
Treble
Level
(dB)
Frequency
(Hz)
You can store up to 5 different equalizer settings
in the equalizer bank (EQ BANK [1] – [5]) and
apply them.
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
2
Rotate MAIN MENU to select
“EQUALIZER”.
3
4
Rotate MENU to select “EQ BANK”.
Rotate –/+ to select the equalizer bank
you want to adjust (EQ BANK [1] – [5]).
5
Rotate MENU to select the parameter.
For details, see “EQUALIZER menu
parameters” below.
6
7
While monitoring the sound, rotate –/+
to adjust the selected parameter.
Repeat steps 5 and 6 to adjust the other
items.
EQUALIZER menu parameters
x EQ BANK
(Equalizer bank selection)
Lets you select the equalizer bank ([1] – [5]). When
you select “OFF”, the equalizer is cancelled.
x FRONT BASS XXX dB
(Front speaker bass level)
x FRONT TREBLE XXX dB
(Front speaker treble level)
x CENTER BASS XXX dB
(Center speaker bass level)
x CENTER MID XXX dB
(Center speaker midrange level)
x CENTER TREBLE XXX dB
(Center speaker treble level)
34GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x SURR/SB BASS XXX dB
(Surround/surround back speaker bass level)
For advanced EQUALIZER menu
adjustments
x SURR/SB TRE. XXX dB
(Surround/surround back speaker treble level)
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON” to enable advanced
adjustments.
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 1 dB steps.
x PRESET X CLEAR
(Equalizer bank clear)
You can reset the adjusted equalizer settings to the
initial setting. For details, see “Clearing stored
Tip
You can adjust the front speaker bass and treble level
with BASS control and TREBLE control.
To apply the stored equalizer
1 Rotate MAIN MENU to select
“EQUALIZER”.
2 Rotate MENU to select “EQ BANK”.
3 Rotate –/+ to select “EQ BANK [1] – [5]”.
To turn off the equalizer
Select “EQ BANK [OFF]”.
Clearing stored equalizer
settings
1
Rotate MAIN MENU to select
“EQUALIZER”.
2
3
Rotate MENU to select “EQ BANK”.
Rotate +/– to select the equalizer (EQ
BANK [1] – [5]) you want to clear.
4
Rotate MENU to select “PRESET X
CLEAR”.
“X” is the number of the selected equalizer
bank.
5
6
Rotate –/+ to select “YES”, then press
ENTER.
“Are you sure?” appears in the display.
Rotate –/+ to select “YES”, then press
ENTER.
“PRESET X CLEARED!” appears in the
display and the adjusted contents of the
selected equalizer bank are cleared.
35GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x i POWER (i.LINK power management)
• AUTO
Advanced settings
Lets you turn off the power of the unnecessary
i.LINK circuits automatically. You can enjoy high
quality digital or analog audio without the influence
of the i.LINK circuits. When set to “AUTO”, it takes
on switching the input when set to “AUTO”.
• EVER ON
Using the CUSTOMIZE menu
to adjust the amplifier
You can adjust various amplifier settings using
the CUSTOMIZE menu.
Lets you keep the power of the i.LINK circuits.
Select if you do not like the time lag that occurs with
the “AUTO” setting.
1
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
x H.A.T.S. (H.A.T.S. (High quality digital Audio
Transmission System) function)
Rotate MENU to select the parameter.
For details, see “CUSTOMIZE menu
parameters” below.
• ON
The digital audio signals input from the i.LINK
component is stored in the buffer temporarily, then
retrieved from the buffer and converted to analog
audio signals at the proper timing. The sound quality
is enhanced because there is no jitter (timing gaps
when reading signals) when transmitting the digital
audio signals. If you do not want to use this function,
select “OFF”.
3
4
Rotate –/+ to adjust the selected
parameter.
items.
CUSTOMIZE menu parameters
• OFF
The initial setting is underlined.
This function is not activated.
x MENU EXPAND (Menu expanding)
Note
• ON
It takes some time to output the sound after the
playback operation is performed on the connected
component (ex., press PLAY button, press STOP
button, press PAUSE button) due to limitations of the
H.A.T.S. system. The time lag depends on the sound
source.
The advanced parameters for the SPEAKER SET
UP, SURR SET UP and LEVEL menus are displayed
and can be adjusted.
and the following pages.
• OFF
x DSD-SW SWAP (DSD-SW swapping)
On some multi channel Super Audio CDs, the 6th
channel is not for the sub woofer, but contains some
other sound (such as reverberation from the ceiling,
etc.).
The advanced parameters are not displayed.
x DTS 96/24 DEC. (DTS 96/24 decoding mode)
• AUTO
When a DTS 96/24 signal is input, it is played back
at 96 kHz sampling frequencies.
• OFF
This item lets you switch the output of the 6th channel
signals from the SUB WOOFER PRE OUT to the
SURROUND BACK terminals.
Even when a DTS 96/24 signal is input, it is played
back at 48 kHz sampling frequencies.
• ON
Note
6th channel DSD signals input through the i.LINK
connection and SUB WOOFER channel signals
input through the MULTI CHANNEL IN 1 or
MULTI CHANNEL IN 2 terminals are output from
the SURROUND BACK terminals, and no sound is
output from the SUB WOOFER PRE OUT.
• OFF
This parameter is valid only in the A.F.D. mode
(page 26). In other sound fields, this parameter is
always set to “OFF”.
x SB DECODING
(Surround back decoding mode)
You can use the CUSTOMIZE menu to set the
Sound is output from the SUB WOOFER PRE OUT
as normal.
surround back decoding mode. See page 29.
• AUTO
• MATRIX
• OFF
36GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
CD/SACD and MD/DAT. You can use DECODE
PRIORITY on the front panel.
• AUTO
This function does not work when “SURR BACK SP”
in the SPEAKER SET UP menu is set to “NO”
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
• PCM
x LIP SYNC (Time alignment)
Initial setting: 0 ms
PCM signals are given priority (to prevent
interruption when playback starts). When set to
“AUTO” and the sound from the digital audio jacks
(for CD, etc.) is interrupted when playback starts, set
to “PCM”. However, when other signals are input,
there may be no sound depending on the format. In
this case, set to “AUTO”.
Lets you delay the output of audio to adjust the gap
between video and audio. You can adjust from 0 ms to
200 ms in 10 ms steps.
This function is not available in the following cases:
– When analog input is selected and DIRECT function
is used.
– When MULTI CH IN 1/2 is selected.
– When DSD signal is input from the i.LINK
component.
x 2 WAY REMOTE
(2 way remote control system)
• ON
Lets you turn on the 2 way remote control system.
Normally, select “ON”.
• OFF
x DC PHASE L. (DC Phase Linearlizer)
Lets you approximate the low frequency phase
characteristics to a traditional analog amplifier.
• OFF
Lets you turn off the 2 way remote control system.
When you use another amplifier, etc. that is also
compatible with the 2 way remote control system,
together with this amplifier, select the component for
which you use the 2 way remote control system.
Then set the 2 way remote control system for the
component to “ON”. For other components, set the 2
way remote control system to “OFF”.
Phase correction is not performed.
• LOW-A, STD-A, HIGH-A, LOW-B, STD-B,
HIGH-B
The bandwidth range of the phase correction
increases in the order of “LOW”, “STD”, “HIGH”.
“B” parameter phase correction provides more
enhanced bass characteristics.
x COLOR SYSTEM
x MIX SCALING (Downmix scaling)
Lets you adjust the downmix scaling processing for
center and sub woofer channels. This parameter can be
set only when the center speaker is set to “MIX”.
• ON
(OSD color system)
(Models of area code CEL only)
Lets you select the color system.
• NTSC
• PAL
The downmix scaling is performed.
• OFF
x OSD H.POSITION
(OSD horizontal position)
The downmix scaling is not performed so that the
sound quality is not deteriorated. If the sound is heard
like a noise at the high input level, set to “ON”.
Initial setting: 4
Lets you adjust the position of the on-screen display
horizontally. You can adjust from 0 to 64.
x S.FIELD LINK (Sound field link)
x OSD V.POSITION
(OSD vertical position)
• ON
Lets you apply the last selected sound field to an
input whenever it is selected. For example, if you
select STADIUM for the CD/SACD input, then
change to a different input and return to CD/SACD,
STADIUM will automatically be applied again.
• OFF
Initial setting: 4
Lets you adjust the position of the on-screen display
vertically. You can adjust from 0 to 32.
x UP YUV HUE (Video hue level)
Initial setting: 4
Sound field link is not activated.
Lets you adjust the hue of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 7.
x DEC. PRIORITY
(Digital audio input decoding priority)
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
x UP YUV SHARPNESS (Video sharpness level)
Initial setting: 4
The initial setting is “AUTO” for VIDEO 1, VIDEO 2,
VIDEO 3, VIDEO 4, VIDEO 5, LD, TV/SAT, TAPE,
TUNER, PHONO and i.LINK, and “PCM” for DVD,
continued
37GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Lets you adjust the sharpness of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 5.
All SPEAKER SET UP menu
parameters
SP EASY SET UP
SPEAKER PATTERN
SUB WOOFER
x UP YUV COLOR (Video chroma level)
Initial setting: 4
Lets you adjust the chroma of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 7.
FRONT SP
CENTER SP
x DIGITAL ASSIGN ?
(Digital audio input assignment)
SURROUND SP-A
SURROUND SP-B
SURR BACK SP
Lets you assign the digital audio input to other input.
For details, see “Assigning the audio input” on
FRONT XXX meter
CENTER XXX meter
SURROUND-A XXX meter
SURROUND-B XXX meter
SURR BACK XXX meter
SUB WOOFER XXX meter
DISTANCE UNIT*
SP-A POSI*
x USER PRESET MEM.?
(User preset memory)
Lets you store the adjusted sound field settings, etc. For
x NAME IN?
(Naming inputs)
Lets you set the name of inputs selected with INPUT
SELECTOR. For details, see “Naming inputs” on
SP-B POSI*
SP CROSSOVER > XXX Hz*
OUTPUT*
Advanced SPEAKER SET UP
menu parameters
* Adjustable only when “MENU EXPAND” is set to
“ON”.
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 18 for the SPEAKER SET UP menu
adjustments. Initial settings are underlined.
x DISTANCE UNIT (Distance unit)
Lets you select the unit of measure for setting
distances.
• feet
The distance is displayed in feet.
• meter
The distance is displayed in meters.
x SP-A POSI
(Surround speaker-A position)*
x SP-B POSI
(Surround speaker-B position)*
Lets you specify the location of your surround speakers
for proper implementation of the surround effects in
38GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Therefore, although it may result in a setting contrary
to the above explanation, we recommend that you
playback multi channel surround encoded software and
select the setting that provides a good sense of
spaciousness and that best succeeds in forming a
cohesive space between the surround sound from the
surround speakers and the sound of the front speakers.
If you are not sure which sounds best, select “BEHD”
and then use the speaker distance parameter and
speaker level adjustments to obtain proper balance.
120˚
100˚
A
A
B
B
x SP CROSSOVER > XXX Hz
(Speaker crossover frequency)
Initial setting: 100 Hz
Lets you set the bass crossover frequency of speakers
set to “SMALL” in the SPEAKER SET UP menu. You
can adjust from 40 Hz to 160 Hz in 10 Hz steps.
D
D
C
x OUTPUT (Preout downmixing)
60
30
• ALL ON
C
Lets you output the sound from both SPEAKERS
and PREOUT jacks. (All downmixing is performed
by DSP.)
• FRONT SP OFF
• SIDE/LOW
Lets you turn off the sound output from front
speakers and perform the analog downmixing. Select
this when you use this amplifier as a preamp for front
speakers only.
Select if the location of your surround speakers
corresponds to section A and C.
• SIDE/HIGH
Select if the location of your surround speakers
corresponds to section A and D.
• BEHD/LOW
• PREOUT ONLY
Lets you output the sound from PREOUT jacks and
not output from SPEAKERS jacks (analog
downmixing is performed). Select this when you use
this amplifier as a full-channel preamp.
Select if the location of your surround speakers
corresponds to section B and C.
• BEHD/HIGH
Select if the location of your surround speakers
corresponds to section B and D.
Advanced SURR SET UP menu
parameters
* This setup item is not available when the surround
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 32 for the SURR SET UP menu
adjustments. Initial settings are underlined.
Tip
Surround speaker position is designed specifically for
implementation of the Cinema Studio EX modes.
For other sound fields, speaker position is not so
critical. Those sound fields were designed under the
premise that the surround speakers would be located
behind the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects becomes unclear unless set to “SIDE”.
Nevertheless, each listening environment has many
variables, like wall reflections, and you may obtain
better results using “BEHD” if your speakers are
located high above the listening position, even if they
are to the immediate left and right.
continued
39GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Normally, select “STD”.
• WET
All SURR SET UP menu
parameters
Select to increase front reverberations.
EFFECT LEVEL
x SCREEN DEPTH (Screen depth)
Lets you create the sensation that the sound of the front
speakers comes from inside the screen in your listening
room, like theatres.
C. WIDTH L_C_R*
DIMENSION F_I_S*
PANORAMA MODE*
FRONT REVERB*
SCREEN DEPTH*
VIR.SPEAKERS*
A.F.D. 2CH SW*
• ON
Lets you create the sensation that the sound comes
from a very large screen with a great amount of
screen depth.
• OFF
This function is not activated.
* Adjustable only when “MENU EXPAND” is set to
“ON”.
x VIR.SPEAKERS (Virtual speakers)
This parameter is especially for the Cinema Studio EX
x C. WIDTH L_C_R
(Center width control)
• ON
Initial setting: (3)
The virtual speakers are created.
• OFF
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
The virtual speakers are not created.
Note
The setting of “SCREEN DEPTH” and
“VIR.SPEAKERS” are not linked with sound fields.
You can adjust the distribution of the center channel
signal, generated through the Dolby Pro Logic II
decoding, to the L/R speakers.
x A.F.D. 2CH SW
(Creating, low frequency signals)
x DIMENSION F_I_S
(Dimension control)
• CREATE
Lets you create low frequency signals for output to
the subwoofer when “A.F.D. AUTO” is selected.
• OFF
Initial setting: midpoint (0)
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
Low frequency signals are not created.
You can adjust the difference between the front
channels and the surround channels.
Advanced LEVEL menu
parameters
x PANORAMA MODE
(Panorama mode)
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 33 for the LEVEL menu adjustments.
Initial settings are underlined.
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
• ON
Lets you enjoy the surround sound by spreading the
sound field of front speakers to the left and right of
the listening position (panorama mode).
• OFF
Panorama mode is not activated.
x FRONT REVERB (Front reverberation)
This parameter is especially for “D.CONCERT HALL
amount of reverberations to add to the front signals
according to the original reverberations in the source.
• STD
40GB
Download from Www.Somanuals.com. All Manuals Search And Download.
hearing the dialogue. If you did not install a center
speaker, this parameter adjusts the level of the center
channel as it is mixed with the sound of the front
speakers. You can adjust from –3 dB to +3 dB in 0.5
dB steps.
All LEVEL menu parameters
TEST TONE
a)
PHASE NOISE
a)
PHASE AUDIO
FRONT L_I_R
Notes
• “SUB WOOFER TRIM” and “CENTER TRIM” can
be adjusted only when the center speaker is set to
“MIX”.
CENTER XXX.X dB
SURROUND L XXX.X dB
SURROUND R XXX.X dB
• “SUB WOOFER TRIM” and “CENTER TRIM” do
not function for Super Audio CD signals from an
i.LINK component, MULTI CH IN signals, or DTS
96/24 decoded signals.
b)
SURR BACK XXX.X dB
c)
SURR BACK L XXX.X dB
c)
SURR BACK R XXX.X dB
x D.RANGE COMP.
SUB WOOFER XXX.X dB
(Dynamic range compressor)
a)
SUB WOOFER TRIM X.X dB
Lets you compress the dynamic range of the sound
track. This may be useful when you want to watch
movies at low volumes late at night.
• OFF
a)
CENTER TRIM X.X dB
MULTI CH 1 SW XXX dB
MULTI CH 2 SW XXX dB
a)
The dynamic range is not compressed.
• STD
D.RANGE COMP.
a)
The dynamic range is compressed as intended by the
recording engineer.
• MAX
Adjustable only when “MENU EXPAND” is set to
“ON”.
b)
When surround back speaker is set to “SINGLE”
The dynamic range is compressed dramatically.
c)
When surround back speaker is set to “DUAL”
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the dynamic
range information included in the Dolby Digital signal.
“STD” is the standard setting, but it only enacts light
compression.
x PHASE NOISE (Phase noise)
Initial setting: OFF
Lets you output the test tone sequentially from adjacent
speakers.
Therefore, we recommend using the “MAX” setting.
This greatly compresses the dynamic range and lets
you view movies late at night at low volumes. Unlike
analog limiters, the levels are predetermined and
provide a very natural compression.
x PHASE AUDIO (Phase audio)
Initial setting: OFF
Lets you output the front 2 channel source sound
(instead of the test tone) sequentially from adjacent
speakers. When i.LINK input is selected, this function
is unavailable.
Note
Dynamic range compression is possible with Dolby
Digital sources only.
x SUB WOOFER TRIM (Sub woofer trim
adjustment)
Initial setting: 0 dB
Advanced EQUALIZER menu
parameters
Lets you adjust the level of the sub woofer when the
signals of sub woofer channel is input. Use this
parameter to adjust the sub woofer level when
connecting headphones or when the sub woofer is not
connected. You can adjust from –6 dB to +6 dB in 1 dB
steps.
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 34 for the EQUALIZER menu
adjustments. Initial settings are underlined.
x CENTER TRIM X.X dB (Center speaker trim
adjustment)
Initial setting: 0 dB
Lets you adjust the output of the center speaker.
Increase this parameter if you are having trouble
continued
41GB
Download from Www.Somanuals.com. All Manuals Search And Download.
All EQUALIZER menu parameters
Storing the adjusted
settings
EQ BANK
FRONT BASS XXX dB
FRONT BASS XXX Hz*
FRONT TREBLE XXX dB
FRONT TREBLE XXX Hz*
CENTER BASS XXX dB
CENTER BASS XXX Hz*
CENTER MID XXX dB
CENTER MID XXX Hz*
CENTER TREBLE XXX dB
CENTER TREBLE XXX Hz*
SURR/SB BASS XXX dB
SURR/SB BASS XXX Hz*
SURR/SB TRE. XXX dB
SURR/SB TRE. XXX Hz*
PRESET X CLEAR
— USER PRESET
You can store the adjusted sound field settings,
etc. as user presets. You can store up to 3 user
presets and easily apply them.
Setting the USER PRESET
1
Adjust the sound field, etc.
For the settings you can store, see “Settings
2
3
4
Rotate MAIN MENU to select
“CUSTOMIZE”.
Rotate MENU to select “USER PRESET
MEM.?”.
* Adjustable only when “MENU EXPAND” is set to
“ON”.
Rotate –/+ to select the USER PRESET
number.
x FRONT BASS XXX Hz (Front speaker bass
frequency)
5
6
Press ENTER.
Initial setting: 500 Hz
You can adjust either to 250 Hz or to 500 Hz.
To store other settings, repeat steps 1
to 5.
x FRONT TREBLE XXX Hz (Front speaker treble
frequency)
Settings that can be stored in
USER PRESET
Initial setting: 2.2 kHz
You can adjust either to 2.2 kHz or to 4.3 kHz.
• Input selected by the INPUT SELECTOR
• INPUT MODE setting
• Selected sound field
x CENTER BASS XXX Hz (Center speaker bass
frequency)
Initial setting: 500 Hz
You can adjust either to 250 Hz or to 500 Hz.
• MULTI CH IN setting
• DIRECT setting
x CENTER MID XXX Hz (Center speaker
midrange frequency)
• NIGHT MODE setting
• C.WIDTH setting
Initial setting: 1 kHz
You can adjust from 100 Hz to 10 kHz in 5 steps.
• DIMENSION setting
x CENTER TREBLE XXX Hz (Center speaker
treble frequency)
• PANORAMA MODE setting
• EFFECT LEVEL setting
• FRONT REVERB setting
• SCREEN DEPTH setting
• VIR.SPEAKERS setting
Initial setting: 2.2 kHz
You can adjust either to 2.2 kHz or to 4.3 kHz.
x SURR/SB BASS XXX Hz (Surround/surround
back speaker bass frequency)
Initial setting: 500 Hz
You can adjust either to 250 Hz or to 500 Hz.
x SURR/SB TRE. XXX Hz (Surround/surround
back speaker treble frequency)
Initial setting: 2.2 kHz
You can adjust either to 2.2 kHz or to 4.3 kHz.
42GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the USER PRESET
1
2
Press USER PRESET repeatedly to
select the USER PRESET you want.
Press ENTER.
Note
If the DIGITAL ASSIGN setting is changed after you
store a USER PRESET and if the stored INPUT
MODE setting cannot be used, a selectable setting is
applied automatically.
Example:
1) Use the DIGITAL ASSIGN function to assign
“DVD OPT” to “TAPE”.
2) Set the INPUT MODE of TAPE to “AUTO 2CH” or
“OPTICAL FIXED”, then store this setting in a
USER PRESET.
3) Use the DIGITAL ASSIGN function to assign
“DVD OPT” to “DVD”.
4) Select the USER PRESET stored in example 2.
The INPUT MODE of TAPE is automatically set to
“ANALOG 2CH FIXED”. You cannot select
“AUTO 2CH” or “OPTICAL FIXED”.
43GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
Other Operations
You can set the amplifier to turn off
automatically at a specified time.
Naming inputs
Press SLEEP repeatedly while the power is
on.
You can enter a name of up to 8 characters for
inputs selected with INPUT SELECTOR, and
display it in the amplifier’s display.
Each time you select or press SLEEP, the
display changes cyclically as follows:
2:00:00 t 1:30:00 t 1:00:00 t 0:30:00 t
OFF
While using Sleep Timer, “SLEEP” lights up in
the display.
1
Rotate INPUT SELECTOR to select an
input you want to create an index name
for.
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
Tip
3
4
Rotate MENU to select “NAME IN?”.
Press ENTER or rotate –/+.
To check the remaining time before the amplifier turns
off, press SLEEP while the power is on. The remaining
time appears in the display.
The cursor flashes and you can select a
character.
5
Use MENU and –/+ to create an index
name.
Rotate –/+ to select a character, then rotate
MENU to move the cursor to the next
position.
Tips
• You can select the character type as follows by
rotating –/+.
Alphabet (upper case) t Numbers t Symbols
• To enter a blank space, rotate –/+ until a blank
space appears in the display.
• If you make a mistake, rotate MENU until the
character you want to change flashes, then rotate
–/+ to select the correct character.
6
7
Press ENTER.
The entered name is registered.
To index other inputs, repeat steps 1 to
44GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Set to
To select
Selecting the speaker
system
OFF**
No speaker output.
(All the sound output from SPEAKERS
and PREOUT jacks are turned off.)
This amplifier allows you to switch between 3
different surround speaker configurations (A, B,
and A+B). There are two sets of surround
speaker terminals (A and B). The SPEAKERS
SURROUND A terminals are for standard
operation with up to 7.1 channels. Use the
SPEAKERS SURROUND B terminals to
connect additional surround speakers for use in
either a separate 5.1 channel system
* When the IMPEDANCE SELECTOR is set to
“8Ω”, connect speakers with a nominal impedance
of 16 ohm or higher. When the IMPEDANCE
SELECTOR is set to “4Ω”, connect the speakers
with a nominal impedance of 8 ohms or higher.
**When you want to turn off the sound output from
SPEAKERS jacks while turning on the sound
output from PREOUT jacks, set the SPEAKERS
FRONT switch to “A”, “B” or “A+B”, then set
“OUTPUT” in the SPEAKER SET UP menu to
“PREOUT ONLY” (page 39).
(independent from the 7.1 channel system), or as
additional speakers to make the 7.1 channel
system into a 9.1 channel system.
Selecting the surround
speaker system
Using only the speakers connected to
the SPEAKERS SURROUND A terminals
This is a standard speaker system for use with
movies and Super Audio CDs.
Set the SPEAKERS SURROUND switch
according to the surround speakers you want to
drive.
Set to
To select
Using the speakers connected to the
SPEAKERS SURROUND B terminals
You can create two separate surround systems, a
7.1 channel system for movies and a 5.1 channel
system for Super Audio CDs. In this case,
connect the surround speakers for movies to the
SPEAKERS SURROUND A terminals and
connect the surround speakers for music to the
SPEAKERS SURROUND B terminals. This is
useful if you mainly listen to Super Audio CDs,
but also want to enjoy a theater-like sound stage
for movies.
A
The speakers connected to the
SPEAKERS SURROUND A terminals
(7.1 channel).
B
The speakers connected to the
SPEAKERS SURROUND B terminals
(5.1 channel).
No sound is output from the surround
back speakers.
A+B*
The speakers connected to both the
SPEAKERS SURROUND A and
SPEAKERS SURROUND B terminals
(9.1 channel).
When this setting is selected, the
parameters set for surround speaker-A in
SPEAKER SET UP are also set for
surround speaker-B.
Selecting the front speaker
system
Set the SPEAKERS FRONT switch according
to the front speakers you want to drive.
* When the IMPEDANCE SELECTOR is set to “8Ω”,
connect speakers with a nominal impedance of 16
ohm or higher. When the IMPEDANCE
Set to
To select
SELECTOR is set to “4Ω”, connect the speakers
with a nominal impedance of 8 ohms or higher.
A
The speakers connected to the
SPEAKERS FRONT A terminals.
B
The speakers connected to the
SPEAKERS FRONT B terminals.
Notes
set separately for the surround speakers connected to
SPEAKERS SURROUND A and SPEAKERS
SURROUND B terminals.
A+B*
The speakers connected to both the
SPEAKERS FRONT A and SPEAKERS
FRONT B terminals (parallel
connection).
continued
45GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Before setting the surround speakers, select the
surround speaker system you use.
Recording
Before you begin, make sure you have
connected all components properly.
Recording on an audio tape or
MiniDisc
You can record on a MiniDisc or cassette tape
using the amplifier. See the operating
instructions of your cassette deck or MD deck if
you need help.
1
2
Select the component to be recorded.
Prepare the component for playing.
For example, insert a CD into the CD
player.
3
4
Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
Press REC OUT SELECTOR +/–
repeatedly to select the input
(component for playing).
REC OUT SELECTOR +/– are for analog
output only. Digital output is available for
SOURCE (current input) only. You can not
select “i.LINK”.
5
Start recording on the recording deck,
then start playback on the playback
component.
Notes
• You cannot record a digital audio signal using a
component connected to the analog TAPE OUT or
MD/DAT OUT jacks. To record a digital audio
signal, connect a digital component to the MD/DAT
OPTICAL OUT jacks.
• Sound adjustments do not affect the signal output
from the TAPE OUT or MD/DAT OUT jacks.
• The signals input to the MULTI CHANNEL INPUT
jacks are not output from the TAPE OUT or MD/
DAT OUT jacks even when MULTI CH IN is being
used. The analog audio signals of the current or
previously used input are output.
• When “OFF” is selected with REC OUT
SELECTOR +/–, no sound is output from TAPE
OUT or MD/DAT OUT jacks.
46GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• The signals input to the MULTI CHANNEL IN jacks
are not output from VIDEO 1 OUT, VIDEO 2 OUT,
or VIDEO 3 OUT jacks even when MULTI CH IN is
being used. The analog audio signals of the current or
previously used input are output.
Recording on a video tape
You can record from a VCR, a TV, or an LD
player using the amplifier. You can also add
audio from a variety of audio sources when
editing a video tape. See the operating
instructions of your VCR if you need help.
1
2
Select the program source to be
recorded.
Prepare the component for playing.
For example, insert the laser disc you want
to record into the LD player.
3
Insert a blank video tape into the VCR
(VIDEO 1, VIDEO 2 or VIDEO 3) for
recording.
4
Press REC OUT SELECTOR +/–
repeatedly to select the input
(component for playing).
5
Start recording on the recording VCR,
then start playing the video tape or
laser disc you want to record.
Tip
You can record the sound from any audio source onto
a video tape while copying from a video tape or laser
disc. Locate the point where you want to start
recording from another audio source, select the
program source, then start playback. The audio from
that source will be recorded onto the audio track of the
video tape instead of the audio from the original
medium. To resume audio recording from the original
medium, select the video source again.
Notes
• The analog audio signals of the current input are
output from the VIDEO 1 OUT, VIDEO 2 OUT, or
VIDEO 3 OUT jacks.
• You cannot record a digital audio signal using a
component connected to the analog VIDEO 1 OUT,
VIDEO 2 OUT or VIDEO 3 OUT jacks. To record a
digital audio signal, connect a digital component to
the VIDEO 1 OPTICAL OUT jack. Note that only
the digitally input signal is output from the VIDEO 1
OPTICAL OUT jack.
• Make sure to make both digital and analog
connections to the TV/SAT or DVD inputs. Analog
recording is not possible if you make only digital
connections.
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to record
from the sources.
47GB
Download from Www.Somanuals.com. All Manuals Search And Download.
If, however, you have a Sony CD changer with
VIDEO OUT jacks, set the command mode to
“CD 2” and connect the changer to the VIDEO
2 jacks on the amplifier (receiver).
CONTROL A1II Control
System
Connections
The CONTROL A1II Control System was
designed to simplify the operation of audio
systems composed of separate Sony
components. CONTROL A1II connections
provide a path for the transmission of control
signals which enable automatic operation and
control features usually associated with
integrated systems.
Currently, CONTROL A1II connections
between a Sony CD player, amplifier (receiver),
MD deck and cassette deck provide automatic
function selection.
You can connect up to 10 CONTROL A1II
compatible components in any order. However,
you can connect only one of each type of
component (i.e., 1 CD player, 1 MD deck, 1 tape
deck and 1 amplifier).
(You may be able to connect more than one CD
player or MD deck, depending on the model.
Refer to the operating instructions supplied with
the respective component for details.)
Example
Note
Do not operate a 2 way remote control unit when the
CONTROL A1II jacks are connected via a PC
interface kit to a personal computer running “MD
Editor” or similar application. Also, do not operate the
connected component in a manner contrary to the
functions of the application, as this may cause the
application to operate incorrectly.
MD
deck
Tape
deck
CD
player
Other
components
Amplifier
(Receiver)
In the CONTROL A1II control system, the
control signals flow both ways, so there is no
distinction of IN and OUT jacks. If a component
has more than one CONTROL A1II jack, you
can use either one, or connect different
components to each jack.
Some CONTROL A1 compatible components
are supplied with a connecting cord as an
accessory. In this case, use the connecting cord
for your connection.
CONTROL A1II and CONTROL A1
compatibility
The CONTROL A1 control system has been updated
to the CONTROL A1II which is the standard system in
the Sony 300 disc CD changer and other recent Sony
components. Components with CONTROL A1 jacks
are compatible with components with CONTROL
A1II, and can be connected to each other. Basically,
the majority of the functions available with the
CONTROL A1 control system will be available with
the CONTROL A1II control system.
When using a commercially available cord, use
a monaural (2P) mini-plug cord less than 2
meters long, with no resistance.
However, when making connections between
components with CONTROL A1 jacks and
Basic Functions
components with CONTROL A1II jacks, the number
of functions that can be controlled may be limited
depending on the component. For detailed information,
refer to the operating instructions supplied with the
component(s).
The input selector on the amplifier
automatically switches to the correct input when
you press the play button on one of the
connected components (Auto input selection).
The CONTROL A1II functions will operate as
long as the component you want to operate is
turned on, even if all of the other connected
components are not turned on.
If you have a Sony CD changer with a
COMMAND MODE selector
If your CD changer’s COMMAND MODE
selector can be set to CD 1, CD 2, or CD 3, be
sure to set the command mode to “CD 1” and
connect the changer to the CD jacks on the
amplifier (receiver).
Note
When recording, do not play any components other
than the recording source. It will cause the automatic
input selection to operate.
48GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Example
This amplifier establishes a LINC with SCD-
XA9000ES. Select i.LINK using the INPUT
SELECTOR on this unit, and set the player to i.LINK
output mode.
i.LINK connection
If you have the i.LINK component SCD-
XA9000ES, connect to this amplifier with an
i.LINK cable (supplied with SCD-XA9000ES).
This amplifier is only compatible with i.LINK
connections to the SCD-XA9000ES. i.LINK
connections to SCD-XA9000ES through other
components, and i.LINK connections to other
component are not guaranteed.
1This amplifier sends a request and path information
to SCD-XA9000ES to establish a transmission path
for the audio signal.
1
,
SCD-XA9000ES
TA-DA9000ES
2
<
Notes
• If a metal object should fall into the i.LINK jack,
short-circuiting may occur and damage the
components.
2SCD-XA9000ES responds to the component,
agreeing to the establishment of a LINC.
• Be sure to insert the plug firmly to prevent
malfunction.
The digital audio signal transmission becomes possible
only after the communication described above has
occurred and a LINC has been established.
This amplifier cannot process incompatible signals
such as DV, MICROMV, or MPEG-TS. Some
i.LINK components conform to copy protection
technology standards and handle encrypted signals.
This amplifier conforms to the copy protection
technology of DTLA (Revision 1.2).
not activated when DSD signals are input to this
amplifier.
Notes
The LINC is cancelled in the following cases.
– When i.LINK cable is connected or disconnected.
– When the input selection is switched.
Establishing a LINC
Before an audio signal can be transmitted
between i.LINK components, a LINC (Logical
INterface Connection) must first be established
between the component receiving the audio
signal and the component sending the audio
signal. Establishing a LINC means establishing
a logical path for the transmission of digital
audio signals between the two components.
Each logical path has an ID number. Since the
component that sends an audio signal must
output the signal to a path, and the component
that receives the signal must input it from the
same path, the path must be mutually known by
both components. During the establishment of a
LINC, the following communication occurs
between the two i.LINK components.
49GB
Download from Www.Somanuals.com. All Manuals Search And Download.
On operation
Before connecting other components, be sure to turn
Additional Information
Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the amplifier and have it checked by qualified
personnel before operating it any further.
off and unplug the amplifier.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any question or problem concerning your
amplifier, please consult your nearest Sony dealer.
On power sources
• Before operating the unit, check that the operating
voltage is identical with your local power supply.
The operating voltage is indicated on the nameplate
at the rear of the amplifier.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• If you are not going to use the amplifier for a long
time, be sure to disconnect the amplifier from the
wall outlet. To disconnect the AC power cord, grasp
the plug itself; never pull the cord.
• (Models of area code U, CA only)
One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet only
one way. If you are unable to insert the plug fully into
the outlet, contact your dealer.
• AC power cord must be changed only at the qualified
service shop.
On heat buildup
Although the unit heats up during operation, this is not
a malfunction. If you continuously use this unit at a
large volume, the cabinet temperature of the top, side
and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
• Place the amplifier in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the amplifier.
• Do not place the amplifier near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
• Do not place the amplifier near equipment such as a
television, video deck or cassette deck. (If the
amplifier is being used in combination with a
television, video deck or cassette deck and is placed
too close to that equipment, noise may result, and
picture quality may suffer. This is especially likely
when using an indoor antenna. Therefore, we
recommend using an outdoor antenna.)
50GB
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound or only a very low-level
sound is heard.
Troubleshooting
• Check that the speakers and components are
connected securely.
If you experience any of the following
difficulties while using the amplifier, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
• Check that you have selected the correct
component with INPUT SELECTOR.
• Check that the SPEAKERS is not set to “OFF”
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
There is no sound no matter which component
is selected.
• When only a very low-level sound is heard, check
to see if NIGHT MODE is activated (page 29).
• The protective device on the amplifier has been
activated. Turn off the amplifier, eliminate the
short-circuit problem and turn on the power again.
• Check that both the amplifier and all components
are turned on.
• Check that the MASTER VOLUME control is not
set at –∞ dB.
• Check that the SPEAKERS is not set to “OFF”
There is no sound from analog 2 channel
sources.
• Check that all speaker cords are connected
correctly.
• Check that the DIGITAL ASSIGN function is not
used to assign the digital audio input for the
• Press MUTING on the remote to cancel the
muting function.
• Check that the INPUT MODE is not set to
“COAXIAL FIXED” nor “OPTICAL FIXED” for
• Check that the MULTI CH IN function is not
selected.
• Check that “OUTPUT” in the SURR SET UP
menu is set to “ALL ON”.
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
amplifier and the component.
There is no sound from digital sources (from
COAXIAL or OPTICAL input jack).
• Check that the DIGITAL ASSIGN function is not
used to assign the digital audio input of the
• Check that the INPUT MODE is not set to
the INPUT MODE is not set to “COAXIAL
FIXED” for the sources from OPTICAL input
jack, nor set to “OPTICAL FIXED” for the
sources from COAXIAL input jack.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the amplifier correctly. Check that all the cords
are fully inserted into the jacks on both the
amplifier and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the amplifier correctly.
Check the connection of the front speaker which is
not outputting any sound.
• Check that the MULTI CH IN function is not
selected.
There is no sound when i.LINK is selected.
• Check that the i.LINK component is connected
correctly.
• Check that SCD-XA9000ES is set to output
signals from the i.LINK jack.
• Make sure you have not connected only the L or R
jack to a monaural component. Use a monaural-
stereo cable (not supplied) and connect it to both
the L and R jacks. However, there will be no
sound from the center speaker when a sound field
(PRO LOGIC, etc.) is selected. When the center
speaker is set to “NO”, sound is output only from
front L/R speakers.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
• Adjust balance parameters in the LEVEL menu.
continued
51GB
Download from Www.Somanuals.com. All Manuals Search And Download.
audio setting (settings for the audio output) of the
connected component.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
Recording cannot be done.
• Check that the components are connected
correctly.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters away
from a TV set or fluorescent light.
• Select the source component with REC OUT
SELECTOR +/–.
• Move your TV away from the audio components.
• Check that equipment such as a video deck or
cassette deck is not placed on top of the amplifier.
• Make sure you have grounded U SIGNAL GND
terminal (only when a turntable is connected).
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the amplifier.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
• Connect your TV to the receiver using the same
type of connecting cord as the one used to connect
10).
There is no sound from the center speaker.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Select the CINEMA STUDIO EX mode
Remote control
• Make sure the center speaker is set to either
The remote does not function.
• Point the remote at the remote sensor on the
amplifier.
There is no sound or only a very low-level
sound is heard from the surround/surround
back speakers.
• Remove any obstacles in the path between the
remote and the amplifier.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Replace all the batteries in the remote with new
ones, if they are weak.
• Check if the command modes of the amplifier and
the remote is the same. If the command mode of
the amplifier and the remote is different, you
cannot operate the amplifier with the remote.
To switch the command mode of the remote, press
?/1 while pressing INPUT MODE. Each time
you press ?/1, the command mode switches
between “C.MODE. AV2” and “C.MODE. AV1”.
(The initial setting is “C.MODE. AV2”.)
• Make sure you select the correct input on the
remote.
• Make sure the surround speakers are set to either
There is no sound from the surround back
speakers.
• Some discs have no Dolby Digital EX flag even
though the packages have Dolby Digital EX
There is no sound from sub woofer.
• When all speakers are set to “LARGE” and
“Neo:6 Cinema” or “Neo:6 Music” is selected,
there is no sound from the sub woofer.
Error messages
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
If there is a malfunction, the display shows a
code of two numbers and a message. You can
check the condition of the system by the
message. Refer to the following table to solve
the problem. If any problem persists, consult
your nearest Sony dealer.
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is
not reproduced.
DECODE ERROR/CHECK CODE 01
Appears when the signal which the amplifier cannot
decode (ex. DTS-CD) is input when “DEC.
PRIORITY” in the CUSTOMIZE menu is set to
“PCM”. Set to “AUTO”.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• When connecting the DVD player, etc. to the
digital input jacks of this amplifier, check the
52GB
Download from Www.Somanuals.com. All Manuals Search And Download.
PROTECTOR/CHECK CODE 11
Specifications
Irregular current is output from the speakers. Turn
off the amplifier, check the speaker connection and
turn on the power again.
Amplifier section
POWER OUTPUT
Rated Power Output at Stereo Mode
(8 ohms, 20 Hz – 20 kHz, THD 0.15%)
200 W + 200 W
(4 ohms, 20 Hz – 20 kHz, THD 0.15%)
220 W + 220 W
PROTECTOR/CHECK CODE 12
The amplifier section is overheated. Check that the
ventilation hole is not covered. Turn off the
amplifier, leave the amplifier for a while and turn on
the power again.
1)
PROTECTOR/CHECK CODE 13
The power section is overheated. Check that the
ventilation hole is not covered. Turn off the
amplifier, leave the amplifier for a while and turn on
the power again.
Reference Power Output
(8 ohms, 1 kHz, THD 0.09%)
2)
FRONT : 200 W + 200 W
2)
CENTER : 200 W
SURR : 200 W + 200 W
SURR BACK : 200 W + 200 W
2)
2)
PROTECTOR/CHECK CODE 21
Turn off the amplifier and consult your nearest Sony
dealer.
(4 ohms, 1 kHz, THD 0.09%)
2)
FRONT : 220 W + 220 W
CENTER : 220 W
SURR : 220 W + 220 W
SURR BACK : 220 W + 220 W
2)
2)
PROHIBITED/CHECK CODE 71
The amplifier cannot output the sound due to the
copyright protection.
2)
1)
Actual Rated Maximum Output at Stereo Mode
(8 ohms, JEITA)
(4 ohms, JEITA)
Actual Rated Maximum Output at Surround Mode
260 W + 260 W
320 W + 320 W
UNKNOWN SIGNAL/CHECK CODE 72
The amplifier is not compatible with the format of
the input signal.
2)
(8 ohms, JEITA)
FRONT : 260 W + 260 W
2)
CENTER : 260 W
2)
SURR : 260 W + 260 W
Reference sections for clearing
the memory
2)
SURR BACK : 260 W + 260 W
2)
(4 ohms, JEITA)
FRONT : 320 W + 320 W
2)
CENTER : 320 W
To clear
See
2)
SURR : 320 W + 320 W
All memorized settings
Customized sound fields
2)
SURR BACK : 320 W + 320 W
1) Depending on the sound field settings and the
source, there may be no sound output.
2) Measured under the following conditions:
Area code
CEL
Power requirements
230 V AC, 50/60 Hz
110 V AC, 60 Hz
TW
KR
230 V AC, 60 Hz
Frequency response
PHONO
RIAA equalization curve
±0.5 dB
Power Amp Block
10 Hz – 50 kHz
± 3 dB (8 ohms)
Inputs (Analog)
PHONO
Sensitivity: 3.5 mV
Impedance: 50 kilohms
4)
S/N3): 90 dB (A, 40 mV
)
continued
53GB
Download from Www.Somanuals.com. All Manuals Search And Download.
* Conforms to the copy protection technology of
DTLA (Revision 1.2).
CD/SACD, TAPE,
MD/DAT, DVD, LD,
TV/SAT, VIDEO 1, 2,
3, 4, 5
Sensitivity: 170 mV
Impedance: 50 kilohms
3)
4)
S/N : 100 dB (A, 2V
)
General
Power requirements
3) Input shorted and sealed at VOL MAX.
Area code
CEL
Power requirements
230 V AC, 50/60 Hz
110 V AC, 60 Hz
4) Weighted network + 20 kHz LPF, input level.
TW
Inputs (Digital)
KR
220 V AC, 60 Hz
CD/SACD, DVD, LD, Impedance: 75 ohms
VIDEO 1, TV/SAT
(Coaxial)
S/N: 100 dB
Power consumption
Power consumption (during standby mode)
1 W
600 W
(A Network, 20 kHz LPF)
CD/SACD, DVD, LD, S/N: 100 dB
TV/SAT, MD/DAT,
VIDEO1, 3 (Optical)
(A Network, 20 kHz LPF)
AC outlets
Area code
CEL
AC outlets
Outputs
1 switched, 100 W MAX
– (no AC outlet)
TAPE, MD/DAT
(REC OUT), VIDEO
1, 2, 3 (AUDIO OUT)
Voltage: 170 mV
TW, KR
Impedance: 2.2 kilohms
Dimensions
430 × 238 × 480 mm
including projecting parts and
controls
FRONT L/R,
CENTER,
SURROUND L/R,
SURROUND BACK
L/R, SUB WOOFER
Voltage: 2 V
Impedance: 220 ohms
Mass (Approx.)
28.5 kg
Supplied accessories
AC power coad (1)
Easy Setup Guide (1)
EQUALIZER
Gain levels
±10 dB, 1 dB step
Remote commander RM-LJ312 (1)
Operating Instructions for RM-LJ312 (1)
R6 (size-AA) batteries (3)
Video section
Inputs/Outputs
Video:
S-video:
1 Vp-p, 75 ohms
Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
For details on the area code of the component you
are using, see page 2.
COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms
P /C /B-Y: 0.7 Vp-p, 75
Design and specifications are subject to change
without notice.
B
B
ohms
P /C /R-Y: 0.7 Vp-p, 75
R
R
ohms
80 MHz HD Pass Through
i.LINK section
Pin
4 pins
Transmission speed
S200 (Maximum data
transmission speed 200
Mbps)
Transmission protocol A/M transmission protocol
Format (input)
Super Audio CD* (DSD
PLAIN)
2 channel linear PCM (IEC-
60958-3)
Sampling frequency: 44.1
kHz
54GB
Download from Www.Somanuals.com. All Manuals Search And Download.
55GB
Download from Www.Somanuals.com. All Manuals Search And Download.
List of button locations and reference pages
Illustration number
How to use this page
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
R
R
Name of button/part Reference page
Main unit
ALPHABETICAL ORDER
NUMBERS AND SYMBOLS
Digital Cinema Sound indicator
5
?/1 (power) 1
DIMMER qh
DIRECT indicator 2
Input indicators qf
IR receptor qg
MULTICHANNEL DECODING
indicator qd
NIGHT MODE qk
ON SCREEN ql
PHONES jack eh
REC OUT SELECTOR +/– wk
SB DEC indicator 4
SLEEP qj
SPEAKERS FRONT switch ef
(45)
SPEAKERS SURROUND switch
SURR BACK DECODING wj
TEST TONE w;
56GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5 6
7
8
9
qg
qd
qs
qa
0
qf
v
qh qj qk ql w; wa ws wd wf wg wh wj
ej eh eg ef ed eseae;
wl
wk
57GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
on a video tape 47
on an audio tape or MD 46
A
Adjusting
CUSTOMIZE parameters
36
S
EQUALIZER parameter 34
LEVEL parameter 33, 40,
41
Selecting
component 22
front speaker system 45
sound field 27–28
SPEAKER SET UP param-
eters 18, 38
Sleep Timer 44
Sound field
customizing 32
speaker volume 21
SURR SET UP parameters
32
pre-programmed 27–28
resetting 33
selecting 27–28
SPEAKER SET UP menu 18,
38
C
Changing
display 23
Speakers
effect level 32
adjusting speaker volume
21
connection 13
Clearing receiver’s memory 17
CONTROL A1 II 48
Crossover frequency 39
CUSTOMIZE menu 36
impedance 13, 14
placement 13
Supplied accessories 54
SURR SET UP menu 32, 40
D
Digital Cinema Sound 27
Dubbing. See Recording
T
Test tone 21
E
Editing. See Recording
Effect level 32
EQUALIZER menu 34
I
Indexing. See Naming
L
Labeling. See Naming
LEVEL menu 40, 41
N
Naming 44
R
Recording
58GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed on 100% recycled paper.
Sony Corporation Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|