Sony Cordless Telephone spp s2430 User Manual

3-225-952-11 (1)  
Co rd le ss  
Te le p h o n e  
US  
Operating Instructions  
SPP-S2430  
©2000 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If your telephone is equipped  
w ith automatic dialers  
When programming emergency numbers and  
(or) making test calls to emergency numbers:  
INFORMATION FOR  
GENERAL TELEPHONES  
1. This equipment complies with Part 68 of the  
FCC rules. On the bottom of this equipment  
is a label that contains, among other  
information, the FCC certification number and  
ringer equivalence number (REN) for this  
equipment. If requested, this information  
must be provided to the telephone company.  
1. Remain on the line and briefly explain to  
the dispatcher the reason for the call.  
2. Perform such activities in the off-peak  
hours, such as early morning or late  
evenings.  
2. The applicable certification jack (connector)  
USOC-RJ11C is used for this equipment.  
Caution  
3. This equipment is designed to be connected to  
the telephone network or premises wiring  
using a compatible modular jack that is Part  
68 compliant.  
You are cautioned that any changes or  
modifications not expressly approved in this  
manual could void your authority to operate this  
equipment.  
The FCC compliant telephone cord and  
modular plug is provided with this  
equipment.  
Note  
4. The REN is used to determine the quantity of  
devices that may be connected to the  
This equipment has been tested and found to  
comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation. This equipment  
generates, uses and can radiate radio frequency  
energy and, if not installed and used in  
accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be  
determined by turning the equipment off and  
on, the user is encouraged to try to correct the  
interference by one or more of the following  
measures:  
telephone line. Excessive RENs on the  
telephone line may result in the devices not  
ringing in response to an incoming call.  
Typically, the sum of the RENs should not  
exceed five (5.0).To be certain of the number  
of devices that may be connected to a line, as  
determined by the total RENs, contact the  
local telephone company.  
5. If this equipment (SPP-S2430) causes harm to  
the telephone network, the telephone  
company will notify you in advance that  
temporary discontinuance of service may be  
required. But if advance notice isnt practical,  
the telephone company will notify the  
customer as soon as possible. Also, you will  
be advised of your right to file a complaint  
with the FCC if you believe it is necessary.  
6. The telephone company may make changes in  
its facilities, equipment, operations or  
– Reorient or relocate the receiving antenna.  
procedures that could affect the operation of  
the equipment. If this happens the telephone  
company will provide advance notice so you  
can make necessary modifications to maintain  
uninterrupted service.  
– Increase the separation between the  
equipment and receiver.  
– Connect the equipment into an outlet on a  
circuit different from that to which the  
receiver is connected.  
7. If trouble is experienced with this equipment  
(SPP-S2430), for repair or warranty  
– Consult the dealer or an experienced radio/  
TV technician for help.  
information, please contact Sony Direct  
Response Center: Tel 1-800-222-7669. If the  
equipment is causing harm to the telephone  
network, the telephone company may request  
that you disconnect the equipment until the  
problem is resolved.  
8. All repairs will be performed in an authorized  
Sony service station.  
9. This equipment cannot be used to party lines  
or coin lines.  
10.This equipment is hearing aid compatible.  
3US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ta b le o f co n t e n t s  
46  
48  
Making calls from the Phone  
Ge t t in g St a rt e d  
7
Transferring the Phone  
Step 1: Checking the package  
50 Switching the phones during a  
11 Step 3: Preparing the battery  
50  
50  
To switch from the base  
handset  
17 Step 5: Setting up the phone  
To switch from the cordless  
51 Talking between the phones  
51  
52  
To talk from the cordless  
To talk from the base phone  
to the cordless handset  
Ba sics  
53  
To transfer from the base  
handset  
54  
To transfer from the cordless  
Te le p h o n e Fe a t u re s  
Ca lle r ID Fe a t u re s  
39  
41  
42  
Storing phone numbers and  
Changing a stored name  
service  
Making calls with one-touch  
57  
Erasing data from the  
Caller ID list  
43  
44  
Storing phone numbers and  
names  
59 Calling back a number from  
the Caller ID list  
Changing a stored name  
4US  
Table of contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61  
62  
Storing a number of the  
Directory  
To change the number of  
64 Using “Caller ID with call  
Ad d it io n a l In fo rm a t io n  
67 Mounting the base phone on a  
wall  
68 Carrying the cordless handset by  
the belt clip  
5US  
Table of contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ge t t in g St a rt e d  
Re a d t h is first  
Before you use your phone, you must first set it up. Heres a quick way  
to set up your phone: Steps 1 to 6.  
St e p 1  
(p a g e 7)  
First,unpack thephoneand thesupplied accessories.  
St e p 2  
(p a g e s 8 t o 10)  
You need todothreethingstosetup the  
basephone,includingfindingthebest  
location forthebasephone.  
St e p 3  
(p a g e s 11 t o 12)  
Insertthebatterypackintothecordless  
handsetand chargeitfor morethan 12  
hours.  
Base phone  
St e p 4  
(p a g e s 13 t o 16)  
Enter thearea codeto usetheCaller ID  
service.  
St e p 5  
(p a g e s 17 t o 21)  
Set up the “Caller ID with callwaiting”  
service,theLongDistanceSaver function  
and thevoicemailservice.  
St e p 6  
(p a g e s 22 t o 23)  
Finally,set theday and time.  
Cordless handset  
Th a t ’s it !  
6US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
St e p 1  
Ch e ckin g t h e p a cka g e co n t e n t s  
Make sure you have received the following items in the package.  
If anything is missing, contact your local Sony dealer.  
Base phone  
AC pow er adaptor (AC-T107)  
Cordless handset  
Charger  
Handset  
Handset cord  
Belt clip  
Telephone  
line cords (2)  
Wall bracket/  
stand for base  
phone  
Rechargeable  
battery pack  
(BP-T24)  
7US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
St e p 2  
Se t t in g u p t h e b a se p h o n e  
Do the following steps:  
• Choose the best location  
• Connect the base phone  
• Choose the dialing mode  
Ch o o se t h e b e st lo ca t io n  
Where you place the base phone affects the reception quality of the  
cordless handset.  
Aw ay from noise sources such as a w indow  
by a street w ith heavy traffic  
Aw ay from television  
sets and other  
electronic equipment  
Aw ay from heat sources, such as radiators,  
airducts, and sunlight  
Aw ay from a microw ave  
oven  
Aw ay from excessive  
moisture, extremely low  
temperatures, dust,  
mechanical vibration, or  
shock  
Aw ay from a personal  
computer  
Ne a r a ce n t ra l lo ca t io n  
a n d o n a le ve l su rfa ce  
Aw ay from another  
cordless telephone  
CAUTION: • Should you experience intermittent loss of audio during a conversation, try  
moving closer to the base or move base phone aw ay from other noise sources.  
• The cordless telephone operates at a frequency that may cause interference to  
nearby TVs and VCRs; the base phone should not be placed near or on the top  
of a TV or VCR; and, if interference is experienced, moving the cordless  
telephone farther aw ay from the TV or VCR w ill often reduce or eliminate the  
interference.  
8US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Co n n e ct t h e b a se p h o n e  
If you want to hang the base phone on the wall, see page 67.  
1
4
Hook the cord.  
To  
HANDSET  
To DC IN 11V  
To an AC outlet  
3
AC pow er adaptor  
(supplied  
To LINE  
AC-T107)  
Telephone line cord  
(supplied)  
2 To a telephone  
outlet  
1
2
3
4
Connectthehandsetcord tothe  
HANDSET jack and to the  
handset.  
To tilt the phone  
If you want to tilt the phone, attach the  
supplied wall bracket on the bottom of  
the base phone.  
Connectthetelephonelinecord  
to the LINE jack and to a  
telephoneoutlet.  
2
1
Align the  
f marks.  
ConnecttheACpower adaptor  
to the DC IN 11V jack and to an  
ACoutlet.  
Raisetheantenna.Makesureit  
pointstowardstheceiling.  
co n t in u e d  
Getting Started  
9US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 2: Se t t in g u p t h e b a se p h o n e (co n t in u e d )  
Notes  
Use only the supplied AC-T107 AC power adaptor.  
Do not use any other AC power adaptor.  
Connect the AC power adaptor to a continuous power  
supply.  
Place the base phone close to the AC outlet so that  
you can unplug the AC power adaptor easily.  
Polarity of the plug  
+
Tip  
Modular  
If your telephone outlet is not modular, contact your  
telephone service company for assistance.  
Ch o o se t h e d ia lin g m o d e  
For the telephone to work properly, select an appropriate dialing mode  
(tone or pulse).  
DIAL MODE sw itch  
Depending on your dialing system, set the DIAL MODE switch as  
follows:  
If your dialing system is  
Set the sw itch to  
Tone  
Pulse  
T
P
If you aren't sure of your dialing system  
Make a trial call with the DIAL MODE switch set to T.  
If the call connects, leave the switch as is; otherwise, set to P.  
10US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 3  
Pre p a rin g t h e b a t t e ry p a ck  
Charge the battery pack for more than 12 hours before you start using  
your cordless handset.  
1
2
Slideopen thebattery  
compartmentlid ofthecordless  
handset.  
BP-T24  
Connectthebatteryconnector  
with correctpolarity (black wire  
goeson lower sideand red wire  
goeson upper side).  
Red  
Black  
3
4
Hook thecordsand insertthe  
battery pack.Then closethelid.  
Hook  
Connect the AC power adaptor  
to an AC outlet and place the  
cordless handset on the charger .  
The CHARGE lamp on the  
charger lightsup when the  
cordlesshandsetisproperly  
seated on thechargeterminals  
ofthecharger.Chargethe  
batterypackfor morethan 12  
hours sothatthebattery isfully  
charged. The CHARGE lamp  
remainsliteven aftercharging  
iscompleted.  
To an AC outlet  
Front side  
CHARGE lamp  
co n t in u e d  
11US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
St e p 3: Pre p a rin g t h e b a t t e ry p a ck (co n t in u e d )  
Battery duration  
A fully charged battery pack lasts for about:  
• Approx. 6 hours when you use the cordless handset continuously  
• Approx. 6 days when the cordless handset is in standby mode.  
Notes  
The battery pack will gradually discharge over a long period of time, even  
when not in use.  
If you leave the battery pack in the cordless handset without charging it, the  
battery pack will be completely discharged.  
It may require several times of charging to recover to its full capacity.  
While charging, the battery pack warms up. This is not a malfunction.  
To obtain the best performance from the battery  
Do not place the cordless handset on the charger after each call. The  
battery works best if the cordless handset is returned to the charger  
after two or three calls. However, do not leave the cordless handset off  
the charger for a long period of time as this will completely discharge  
the battery pack.  
When to purchase a new battery pack  
If the battery lasts only a few minutes even after 12 hours of charging,  
the usable life of the battery has expired and needs replacement.  
Contact your local Sony authorized dealer or service center, and ask  
for a Sony BP-T24 rechargeable battery pack.  
Note  
Battery life may vary depending on usage condition and ambient temperature.  
12US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 4  
En t e rin g t h e a re a co d e  
When you use this phone for the first time, or move to an area that has a  
different area code, you must enter the area code. Otherw ise, you cannot use  
some functions of this phone and the Caller ID functions.  
This is also necessary because the phone must be able to select an area code to  
properly dial a call from the Caller ID list.  
Depending on your region, enter the 3-digit area code as follows:  
Case 1.  
If 7-digit dialing (no area code) is accepted for local calls in your area, see “To enter  
your home area code” below.  
If you live in an area where calls from or to other local areas can also be made by 10-digit dialing  
(area code + number), you can register up to 5 local area codes with this telephone to take  
advantage of this system. See “To enter the local area code (For 10 digits phone number users)”  
on page 15.  
Case 2.  
If 10-digit dialing (area code + number) is required for all local calls in your area, see  
“To enter the local area code (For 10 digits phone number users)” on page 15.  
Entering the area code is only possible on the base phone.  
To e n t e r yo u r h o m e a re a co d e  
1
2
Press (PROGRAM).  
(ERASE)  
Turn Jog Dial to choose “BASE  
SETTINGS”, and then press Jog  
Button (ENTER).  
BASE SETTINGS  
GO BACK  
Jog Button  
(ENTER)  
AREA CODE  
PHONE SERVICES  
MESSAGES LAMP  
3
Press Jog Button (ENTER).  
AREA CODE  
GO BACK  
HOME :  
LOCAL 1:  
LOCAL 2:  
co n t in u e d  
Getting Started  
13US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
St e p 4: En t e rin g t h e a re a co d e (co n t in u e d )  
4
Press Jog Button (ENTER) again.  
ENTER HOME  
AREA CODE.  
“ENTER HOME AREA CODE.” appears on  
the display.  
_
5
6
Enter the three digits of your home area code  
using the dialing keys.  
Press (PROGRAM).  
You hear a long confirmation beep.  
Notes  
If the home area code is already entered, it appears on the display in step 3.  
To enter a different home area code, see “To change the home area code”  
below.  
Do not allow more than 20 seconds to elapse during the operation procedure.  
If the area code has not been entered, calling back from the Caller ID list and  
storing the Caller ID data into the Phone Directory cannot be performed.  
If the home area code is not correctly entered, “SEND TO CORDLESS  
HANDSET FAILED.” will appear on the display and five short error beeps  
will be heard after (PROGRAM) is pressed in step 6. Move the cordless  
handset closer to the base phone, and then start over the procedure.  
Tips  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Button (ENTER).  
You may press Jog Button (ENTER) instead of (PROGRAM) in step 6.  
To check the current home area code, perform steps 1 to 3. The home area  
code appears on the display for about 20 seconds.  
To change the home area code  
1 Perform steps1to4on pages13to14.  
Thecurrenthomearea codeappearson thedisplay.  
2 Press (ERASE)toerasethecurrenthomearea code.  
3 Enter a new homearea codeusing thedialing keys.  
4 Press (PROGRAM).  
You hearalongconfirmation beep.  
To erase the home area code  
You can erase the home area code. Perform steps 1 and 2 above, then  
press (PROGRAM).  
The home area code will be erased, and you hear a long confirmation  
beep.  
14US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To e n t e r t h e lo ca l a re a co d e (Fo r 10 d ig it s  
p h o n e n u m b e rs u se rs)  
If a call matches one of the local area codes you entered, the phone  
number will be registered with 10 digits in the Caller ID list (area code  
+ number). If a call does not match one of the local area codes you  
entered, the phone number will be registered with 11 digits in the  
Caller ID list (1 + area code + number). Some regions of the country  
allow you to have more than one local area code. (Up to five local area  
codes can be entered in this phone.)  
1 Perform steps1to3on page13.  
2 Select the number (“LOCAL 1” to “LOCAL 5”)  
AREA CODE  
HOME :  
toenter thelocalarea codeby turning Jog Dial.  
LOCAL 1:  
LOCAL 2:  
LOCAL 3:  
3 Press Jog Button (ENTER).  
“ENTER LOCAL AREA CODE 1.” appears on  
the display when you select “LOCAL 1” in step  
2.  
4 Enter thethreedigitsofthelocalareacodeusing  
thedialingkeys.  
5 Press (PROGRAM).  
You hearalongconfirmation beep.  
Notes  
If the local area code is already entered, it appears on the display in step 2. To  
enter a different local area code, see “To change the local area code” on page  
16.  
Do not allow more than 20 seconds to elapse during the operation procedure.  
If the local area code is not correctly entered, “SEND TO CORDLESS  
HANDSET FAILED.” will appear on the display and five short error beeps  
will be heard after (PROGRAM) is pressed in step 5. Move the cordless  
handset closer to the base phone, and then start over the procedure.  
Tips  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Button (ENTER).  
You may press Jog Button (ENTER) instead of (PROGRAM) in step 5.  
To check the current local area code, perform steps 1 and 2. The local area  
code appears on the display for about 20 seconds.  
co n t in u e d  
15US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 4: En t e rin g t h e a re a co d e (co n t in u e d )  
To change the local area code  
1 Perform steps1to3on page15.  
Thecurrentlocalarea codeappearson thedisplay.  
2 Press (ERASE)toerasethecurrentlocalarea code.  
3 Enter a new localarea codeusing thedialing keys.  
4 Press (PROGRAM).  
You hearalongconfirmation beep.  
To erase the local area code  
You can erase the local area code. Perform steps 1 and 2 on page 15,  
then press (PROGRAM). The local area code will be erased, and you  
hear a long confirmation beep.  
16US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 5  
Se t t in g u p t h e p h o n e se rvice s  
Set up the “Caller ID with call waiting”service, the Long Distance  
Saver function and the voice mail service before use. Setting up the  
phone services is only possible on the base phone.  
To se t u p t h e Ca lle r ID w it h ca ll w a it in g ” se rvice  
In order to use this service, you must first subscribe to “Caller ID with  
call waiting” service (see page 64). The “Caller ID with call waiting”  
service is preset to “ACTIVE”.  
1
2
Press (PROGRAM).  
(ERASE)  
Turn Jog Dial to choose “BASE  
SETTINGS”, and then press Jog  
Button (ENTER).  
3
Turn Jog Dial to choose  
“PHONE SERVICES”, and then  
press Jog Button (ENTER).  
Jog Button  
(ENTER)  
PHONE SERVICES  
GO BACK  
(LONG DIST. SAVER)  
CALL WAITING ID  
VOICE MAIL  
LONG DISTANCE  
4
5
Press Jog Button (ENTER).  
CALL WAITING ID  
GO BACK  
ACTIVE  
INACTIVE  
Turn Jog Dial to choose  
“ACTIVE” or “INACTIVE”, and  
then press Jog Button (ENTER).  
You hear a long confirmation  
beep.  
co n t in u e d  
17US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
St e p 5: Se t t in g u p t h e p h o n e se rvice s (co n t in u e d )  
Note  
Do not allow more than 20 seconds to elapse during the operation procedure.  
Tip  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Button (ENTER).  
18US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To se t u p t h e Lo n g Dist a n ce Sa ve r fu n ct io n  
Many telephone companies and service providers nowadays offer low-  
rate long distance calls separate from your standard long distance  
provider. Such services are usually initiated by dialing an access  
number prior to the long distance call itself.  
The Long Distance Saver function enables you to dial the access  
number of these special long distance service companies by pressing  
just (LONG DIST. SAVER). After setting up the access number and  
activating the button function in the menu, you only need to press  
(LONG DIST. SAVER) for dialing the access number of your special long  
distance carrier.  
In order to use this function, you must first activate the button function  
by memorizing the access number of your choice in the menu and by  
setting the long distance menu function to “ACTIVE”  
The long distance menu is preset to “INACTIVE”, no preset access  
number is registered.  
To set up the access number  
1 Perform steps1and 3on page17.  
2 Turn Jog Dial to choose “LONG DISTANCE”, and then  
press Jog Button (ENTER).  
3 Turn Jog Dial to choose “ACCESS NUMBER”, and then  
press Jog Button (ENTER).  
4 Enter theaccessnumber using thedialing keys.  
5 Press (PROGRAM).  
6 Turn Jog Dialto chooseYES” to activate  
(LONG DIST. SAVER), and then press Jog Button (ENTER).  
You hearalongconfirmation beep.  
co n t in u e d  
19US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 5: Se t t in g u p t h e p h o n e se rvice s (co n t in u e d )  
Notes  
DO NOT USE (LONG DIST. SAVER) to dial EMERGENCY services, customer  
service numbers, your local telephone company, local numbers or toll  
free numbers.  
If you press (LONG DIST. SAVER) twice, the dialing of the registered access  
number is cancelled and “[LONG DISTANCE]” disappears from the display.  
If the access number is not correctly set, “SEND TO CORDLESS HANDSET  
FAILED.” will appear on the display and five short error beeps will be heard  
after Jog Button (ENTER) is pressed in step 6. Move the cordless handset  
closer to the base phone, and then start over the procedure.  
You can register up to 24 digits as an access number.  
To change the access number  
1 Perform steps1and 3on page19.  
Thecurrentaccessnumber appearson thedisplay.  
2 Press (ERASE)toerasethecurrentaccessnumber.  
3 Enter a new accessnumber using thedialing keys.  
4 Press (PROGRAM).  
5 Turn Jog Dialto chooseYES” to activate  
(LONG DIST. SAVER), and then press Jog Button (ENTER).  
You hearalongconfirmation beep.  
To activate/deactivate the Long Distance Saver function  
1 Perform steps1to3on page17.  
2 Turn Jog Dial to choose “LONG DISTANCE”, and then  
press Jog Button (ENTER).  
3 Turn Jog Dial to choose “ACTIVE” or “INACTIVE”(to  
deactivate),and then pressJog Button (ENTER).  
You hearalongconfirmation beep.  
Notes  
If you choose “INACTIVE” in step 3, (LONG DIST. SAVER) will be deactivated  
and you cannot use (LONG DIST. SAVER) even with a registered access  
number until the function is activated again.  
Some Long Distance services may not be available in your state. Prices and  
conditions may vary. For details, contact your telephone company or your  
long distance provider. Some long distance call programs require a  
subscription with the carrier company before usage.  
If it is not correctly set in “ACTIVE” or “INACTIVE”, “SEND TO  
CORDLESS HANDSET FAILED.” will appear on the display and five short  
error beeps will be heard after Jog Button (ENTER) is pressed in step 3. Move  
the cordless handset closer to the base phone, and then start over the  
procedure.  
20US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To se t u p t h e vo ice m a il se rvice  
In order to use this service, you must first subscribe to voice mail  
service (see page 65). The voice mail service is preset to “ACTIVE”.  
1 Perform steps1to3on page17.  
2 Turn Jog Dial to choose “VOICE MAIL”, and then press Jog  
Button (ENTER).  
3 Turn Jog Dial to choose “ACTIVE” or “INACTIVE”, and  
then press Jog Button (ENTER).  
You hearalongconfirmation beep.  
21US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St e p 6  
Se t t in g t h e d a y a n d t im e  
1
2
Press (PROGRAM).  
Turn Jog Dial to choose “BASE  
SETTINGS”, and then press Jog  
Button (ENTER).  
3
Turn Jog Dialto choose  
“CLOCK”, and then press Jog  
Button (ENTER).  
Jog Button  
(ENTER)  
CLOCK  
GO BACK  
SUNDAY  
MONDAY  
TUESDAY  
4
Setthecorrectdayoftheweek  
by turning Jog Dial,and then  
press Jog Button (ENTER).  
ENTER HOUR AND  
PRESS JOG BUTTON  
12:00AM  
22US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ENTER MINUTE AND  
PRESS JOG BUTTON  
5
6
7
Set thehour (1to 12)by turning Jog Dial,and  
then press Jog Button (ENTER).  
12:00AM  
ENTER AM/PM AND  
PRESS JOG BUTTON  
Settheminute(00to59)by turning Jog Dial,  
and then press Jog Button (ENTER).  
12:00AM  
Choose “AM” or “PM” by turning Jog Dial, and  
then press Jog Button (ENTER).  
You hear alongconfirmation beep.Then the  
phonestartscountingtime.  
Notes  
Do not allow more than 60 seconds to elapse during the operation procedure.  
“SUN 12:00AM” on the display of the base phone flashes when the day and  
time is cleared due to a power interruption, or when you connect the base  
phone to the AC outlet for the first time.  
Tip  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Button (ENTER).  
23US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Id e n t ifyin g t h e p a rt s  
Refer to the pages indicated in parentheses for details.  
Base phone  
qa  
qs  
1
2
3
4
qd  
5
6
qf  
qg  
qh  
qj  
qk  
ql  
w;  
wa  
7
8
9
0
1 Display w indow (p. 31, 55)  
8
TONE button (p. 32)  
Allows you to switch temporarily to  
tone dialing.  
2 VOLUME +/– buttons  
(p. 32)  
Adjusts the handset or speaker  
volume.  
9 SPEAKERPHONE button  
(p. 31)  
Lets you make or receive a call.  
3 NEW CALL lamp (p. 56)  
Flashes when there is a “NEW”  
data in the Caller ID list.  
0 #button (p. 62)  
Used to change the number of  
digits of the phone number in the  
Caller ID list.  
4 Handset (p. 9, 31, 37)  
5 Speaker  
qa ERASE button (p. 14, 20)  
qs PROGRAM button (p. 13)  
qd Antenna (p. 9, 67)  
6 Dialing keys (p. 31)  
7 LONG DIST. SAVER button  
(p. 19, 31)  
Lets you make a long distance call  
with the registered access number.  
qf MESSAGES lamp (p. 65)  
Flashes when you have messages.  
qg Jog Button (ENTER) (p. 13)  
24US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
wh  
ws wd wf wg  
qh Jog Dial (p. 13, 56)  
wd DIAL MODE sw itch (p. 10)  
Selects pulse or tone dialing.  
qj REDIAL/PAUSE button (p. 33)  
Redials one of the last five numbers  
called/ inserts a pause in the dialing  
sequence.  
wf DC IN 11V jack (p. 9, 67)  
wg LINE (telephone line) jack  
(p. 9, 67)  
qk INTERCOM button (p. 52)  
wh HANDSET jack (p. 9)  
Lets you talk between the base  
phone and cordless handset.  
ql CALL WAITING/FLASH button  
(p. 32, 64)  
Switches to a second call if you  
have “call waiting” service, or lets  
you make a new call.  
w; HOLD button (p. 32)  
Puts a call on hold.  
wa MIC (microphone)  
ws Hook for AC pow er adaptor  
cord (p. 9, 67)  
co n t in u e d  
Getting Started  
25US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Id e n t ifyin g t h e p a rt s (co n t in u e d )  
Cordless handset  
1
2
qd  
qf  
qg  
3
4
5
6
7
qh  
qj  
qk  
ql  
w;  
8
9
0
qa  
qs  
1 Antenna  
0
TONE button (p. 29)  
Allows you to switch temporarily to  
tone dialing.  
2 Speaker [EZfit] (p. 30)  
3 Display w indow (p. 28, 55)  
4 Jog Dial (p. 39, 56)  
qa HOLD button (p. 29)  
Puts a call on hold.  
5 TALK button (p. 28)  
qs RING sw itch (p. 36)  
Lets you make or receive a call.  
Switches the ringer to on/ off.  
6 INTERCOM button (p. 51)  
qd CALL WAITING/FLASH button  
Lets you talk between the base  
phone and the cordless handset.  
(p. 29, 64)  
Switches to a second call if you  
have “call waiting” service, or lets  
you make a new call.  
7 LONG DIST. SAVER button  
(p. 19, 29)  
Lets you make a long distance call  
with the registered access number.  
qf REDIAL/PAUSE button  
(p. 33, 41)  
Redials one of the last five numbers  
called/ inserts a pause in the dialing  
sequence.  
8 Dialing keys (p. 28)  
9 Battery compartment (p. 11)  
26US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
wa  
ws  
qg OFF button (p. 28)  
Allows you to disconnect the call.  
qh #button (p. 62)  
Used to change the number of  
digits of the phone number in the  
Caller ID list.  
qj PROGRAM button (p. 39)  
qk ERASE button (p. 41)  
ql ONE-TOUCH DIAL (A, B, C)  
buttons (p. 42)  
w; Microphone  
wa I (HEADSET) jack (p. 28, 35, 69)  
ws VOL (volume) sw itch (p. 29)  
Adjust the cordless handset  
volume.  
27US  
Getting Started  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ba sics  
Ma kin g ca lls  
1
2
Pick up thecordlesshandset  
from thecharger.  
(LONG DIST. SAVER)  
Press (TALK)and wait until  
“TALK” appears on the display  
and thedisplay alsoshowsthe  
talk timein hours,minutesand  
seconds.  
(CALL WAITING/FLASH)  
The dialing keys light up.  
You then hear adialtone.  
I(HEADSET)  
jack  
VOL sw itch  
“CORDLESS HANDSET IN  
USE” appearson thedisplay of  
thebasephone.  
(*TONE)  
(HOLD)  
Ifyou hear fiveshort error  
beeps and “OUT OF RANGE”  
appearson thedisplay,move  
closertothebasephone.  
(ERASE)  
3
4
Dialthephonenumber.  
(REDIAL/PAUSE)  
When youredonetalking,press  
(OFF)or replacethecordless  
handseton thecharger.  
Thedisplay turnsoff.  
To make a call after checking the phone number  
You can dial the phone number before pressing (TALK) or  
(LONG DIST. SAVER). If you make a mistake when dialing the phone  
number, press (ERASE) to erase the number.  
28US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Making calls w hen the headset is connected  
When a headset (optional) is connected to the I  
(HEADSET) jack on the cordless handset, you can  
talk through the headset.  
Open  
Making calls using the Long Distance Saver function  
Set the menu for the Long Distance Saver function to “ACTIVE”. See  
“To set up the Long Distance Saver function” on page 20.  
1 Pick up thecordlesshandsetfrom thecharger.  
2 Press (LONG DIST. SAVER).  
“[LONG DISTANCE]” appears on the display.  
To cancelthis function,press (LONGDIST. SAVER)again or  
press (TALK).  
3 Dialthelongdistancephonenumber(e.g.,1-201-123-4567,  
or011-...).  
4 When youredonetalking,press (OFF)or replacethe  
cordlesshandseton thecharger.  
To make a call via Private Branch Exchange (PBX)  
Before pressing (LONG DIST. SAVER) in step 2 above, enter the outside  
line access digit (e.g., 9).  
Additional tasks  
To  
Do this  
Adjust the cordless  
handset volume  
Set the VOL switch to H (high), M (middle) or L (low).  
Put a call on hold  
Press (HOLD). “HOLD” appears on the display.  
Press (HOLD) again or pick up the cordless handset  
from the charger (When Quick talk is set to “USE”; see  
page 36) to resume the conversation.  
Switch to tone dialing  
temporarily  
Press (*TONE) after youre connected.  
The line will remain in tone dialing until disconnected.  
Switch to another call  
Press (CALL WAITING/FLASH).  
(“call waiting” service*)  
Press (CALL WAITING/FLASH) again to return to the first  
caller.  
* You need to subscribe to this service from your telephone company.  
co n t in u e d  
Basics 29US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ma kin g ca lls (co n t in u e d )  
Notes  
When making a call on the cordless handset, “ ” appears on the display  
indicating the receiver sensitivity with the base phone. Three bars indicate a  
good reception, no bar indicates a bad reception. When calling from an area  
with poor reception, you may experience interference or the call may be  
disconnected, so try to use the cordless handset in areas that have a good  
reception.  
When you increase the sound volume, in some cases the back ground noise  
may be increased as well. You should adjust the volume accordingly.  
If the cordless handset beeps every second during a conversation and “ ”  
appears on the display, move closer to the base phone; otherwise, you will  
hear five short error beeps and “OUT OF RANGE” will appear on the  
display, and the call will be disconnected after 30 seconds.  
While talking with an outside caller via the base phone, you cannot make a  
call with the cordless handset. If you press (TALK), “BASEPHONE IN USE”  
appears on the display and you will hear a busy tone.  
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.  
EZfit  
The “EZfit” adjusts to fit any shape ear,  
thereby ensuring clear voice reception.  
If the battery becomes w eak during a call  
The cordless handset will beep twice per second, “BATTERY LOW”  
appears on the display. Finish your call and replace the cordless  
handset on the charger to charge the battery pack. Or, to continue your  
phone conversation with the base phone, press (HOLD) on the cordless  
handset to hold the line, and then pick up the handset or press  
(SPEAKERPHONE) on the base phone.  
For optimum performance, charge the battery for a full 12 hours.  
Note that during the initial charge time (approx. 10 minutes), “PLEASE  
WAIT...” and “BATTERY LOW” appear on the display and the  
cordless handset cannot be used.  
After “BATTERY LOW” turns off, you may be able to use the cordless  
handset, but the battery duration will be very short; thus it is  
recommended that you fully charge the battery before next use.  
30US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Making calls w ith the base phone  
(REDIAL/PAUSE)  
(PROGRAM)  
(CALL WAITING/ FLASH)  
(VOLUME)  
Pick up the handset or press  
(SPEAKERPHONE) on the base phone.  
“TALK” or “SPEAKERPHONE” appears  
on the display and the display also shows  
the talk time in hours, minutes and  
seconds.  
(ERASE)  
(*TONE)  
Dial the phone number.  
Jog  
When youre done talking, replace the  
handset in the cradle or press  
(SPEAKERPHONE) again.  
Button  
(ENTER)  
Jog Dial  
(LONG DIST. SAVER)  
(HOLD)  
(SPEAKERPHONE)  
To make a call after checking the phone number  
You can dial the phone number before picking up the handset or  
before pressing (SPEAKERPHONE). If you make a mistake when  
dialing the phone number, press (ERASE) to erase the number.  
Making calls using the Long Distance Saver function  
Set the menu for the Long Distance Saver function to “ACTIVE”. See  
“To set up the Long Distance Saver function” on page 20.  
1 Pick up thehandset or press (SPEAKERPHONE)on thebase  
phone.  
2 Press (LONG DIST. SAVER).  
“[LONG DISTANCE]” appears on the display.  
To cancelthis function,press (LONGDIST.SAVER)again.  
3 Dialthelongdistancephonenumber(e.g.,1-201-123-4567,  
or011-...).  
4 When youredonetalking,replacethehandsetin thecradle  
or press (SPEAKERPHONE)again.  
To make a call via Private Branch Exchange (PBX)  
Before pressing (LONG DIST. SAVER) in step 2 above, enter the outside  
line access digit (e.g., 9).  
co n t in u e d  
Basics 31US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ma kin g ca lls (co n t in u e d )  
Additional tasks  
To  
Do this  
Adjust the handset or  
speakerphone volume  
During phone conversation, press (VOLUME)(+)  
or (-).  
There are 3 steps for the handset volume level, and  
7 steps for the speakerphone volume level.  
Put a call on hold  
Press (HOLD). “HOLD” appears on the display.  
Press (HOLD), (SPEAKERPHONE), or pick up the  
handset from the base phone to resume the  
conversation.  
Switch to tone dialing  
temporarily  
Press (*TONE) after youre connected.  
The line will remain in tone dialing until  
disconnected.  
Switch to another call  
(“call waiting” service*)  
Press (CALL WAITING/ FLASH).  
Press (CALL WAITING/ FLASH) again to return to the  
first caller.  
* You need to subscribe to the service from your telephone company.  
Notes  
While talking with an outside caller via the cordless handset, the display on  
the base phone shows “CORDLESS HANDSET IN USE” and you cannot  
make a call with the base phone.  
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.  
Tip  
You can switch between phone conversations via the handset and those via the  
speakerphone, simply by picking up the handset while talking over the  
speakerphone, or by pressing (SPEAKERPHONE) while talking over the handset.  
To obtain the best speakerphone performance  
• You may not be able to hear the other partys voice in a noisy place.  
Therefore, use the speakerphone in a quiet room.  
• Do not bring your hand or other object too close to the microphone  
or you will hear a shrill noise (“feedback”).  
• When the speaker volume is loud, or the base phone has been placed  
close to a wall, you may find that the volume drops suddenly. This  
is due to a circuit in the telephone designed to protect against  
feedback. In such cases, lower the speaker volume slightly.  
32US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Re d ia lin g  
Both the base phone and the cordless handset can each individually  
store five dialed phone numbers.  
1
2
Press (REDIAL/PAUSE).  
Turn  
Press  
Display thenameor phone  
number you want tocallby  
turning Jog Dial,and then press  
Jog Dial.(Ifyoureatthebase  
phone,pressJogButton  
(ENTER).)  
3
Turn Jog Dial to choose “DIAL”  
or “LONG DISTANCE”, and  
then pressJog Dial(or Jog  
Button (ENTER)).  
(PROGRAM)  
Thephonenumber willbe  
redialed.  
Notes  
When the Long Distance Saver function is set to “ACTIVE”, “LONG  
DISTANCE” call can be made (see page 20).  
The redial memory only registers up to 30 digits. Exceeding numbers will not  
be redialed.  
In the case of a power failure, only the redial on the base phone will be  
erased.  
The redial button does not store the access number of the Long Distance  
Saver. To redial a long distance call, press (LONG DIST. SAVER), then  
(REDIAL/PAUSE).  
Tips  
When “p” is displayed on the right end of the phone number on the redial list  
in step 2, it means that some number follows the displayed phone number.  
Moreover, when the phone number is selected by turning Jog Dial, all of the  
phone number is displayed in two lines.  
If you redial the same number repeatedly, this number will only be counted  
as one number of the total five registered numbers that can be redialed.  
When dialing from a phone number with a registered name, that name will  
be displayed in the list in step 2.  
co n t in u e d  
Basics 33US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ma kin g ca lls (co n t in u e d )  
To store the dialed phone number into the Phone Directory  
1 Display thenameor phonenumber you wanttostoreby  
doing steps1and 2on page33.  
2 Turn Jog Dialto choose “PROGRAM”,and then press Jog  
Dial.(Ifyoureat thebasephone,pressJog Button (ENTER).)  
3 Enter thenameby doing steps4and 5on page40.  
4 Turn Jog Dialto choose “[PGM]”,and then press Jog Dial(or  
Jog Button (ENTER)).  
You hear alongconfirmation beep,and thenameand the  
numberarestored.  
Note  
The dialed phone numbers of up to 20 digits can be stored in the Phone  
Directory.  
To erase the dialed phone number one by one  
1 Display thenameor phonenumber you wanttoeraseby  
doing steps1and 2on page33.  
2 Turn Jog Dial to choose “ERASE REDIAL”, and then press  
Jog Dial.(Ifyoureatthebasephone,pressJog Button  
(ENTER).)  
3 Turn Jog Dialto choose “YES”,and then press Jog Dial(or  
Jog Button (ENTER)).  
You hear a long confirmation beep,and thenumber is  
erased.  
To erase the entire dialed phone numbers at once  
1 Press (PROGRAM).  
2 Turn Jog Dial to choose “MEMORY MANAGE”, and then  
pressJog Dial.(Ifyoureatthebasephone,pressJog Button  
(ENTER).)  
3 Turn Jog Dial to choose “ERASE ALL RDL”, and then press  
Jog Dial (or Jog Button (ENTER)).  
4 Turn Jog Dial to choose “ERASE REDIAL”, and then press  
Jog Dial (or Jog Button (ENTER)).  
You hearalongconfirmation beep,and theentirenumber  
areerased.  
34US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Re ce ivin g ca lls  
1
When you hear thephonering:  
• Press (TALK).  
or  
• Pick up thecordlesshandset  
from thechargerwhen the  
(CALL WAITING/FLASH)  
cordlesshandsetisplaced on  
thecharger.(When Quick talk  
isset to “USE”;seepage36)  
I(HEADSET)  
jack  
“TALK” appears on the display  
and thedisplay alsoshowsthe  
talk timein hours,minutesand  
seconds.  
VOL sw itch  
“CORDLESS HANDSET IN  
USE” appearson thedisplay of  
thebasephone.  
(HOLD)  
(PROGRAM)  
2
When youredonetalking,press  
(OFF)or replacethecordless  
handseton thecharger.  
Thedisplay turnsoff.  
Receiving calls w hen the headset is connected  
When a headset (optional) is connected to the I  
(HEADSET) jack on the cordless handset, you can  
talk through the headset.  
Open  
co n t in u e d  
Basics 35US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Re ce ivin g ca lls (co n t in u e d )  
Additional tasks  
To  
Do this  
Adjust the cordless handset  
volume  
Set the VOL switch to H (high), M (middle) or L  
(low).  
Put a call on hold  
Press (HOLD). “HOLD” appears on the display.  
Press (HOLD) again or pick up the cordless  
handset from the charger (When Quick talk is  
set to “USE”; see below) to resume the  
conversation.  
Switch to another call  
(“call waiting” service*)  
Press (CALL WAITING/FLASH).  
Press (CALL WAITING/FLASH) again to return to  
the first caller.  
Receive a call by only picking  
up the cordless handset from  
the charger, without pressing  
(TALK)(Quick talk)  
Press (PROGRAM). Turn Jog Dial to choose  
“QUICK TALK”, then press Jog Dial.  
Turn Jog Dial to choose “USE”, then press Jog  
Dial.  
* You need to subscribe to this service from your telephone company.  
Note  
If there is an incoming call during intercom conversation, intercom call will be  
disconnected, and both the base phone and the cordless handset will ring.  
Tip  
To inform you of an incoming call, the display shows “** RINGING **” even  
when you set the RING switch on the cordless handset to OFF.  
If you have subscribed to the Caller ID service;  
the callers number and/ or name appears on the display when you receive a  
call (see page 55) or when another call comes in by “call waiting” service.  
the name stored in the one-touch dialing or Phone Directory appears on the  
display if the call matches the number stored on ONE-TOUCH DIAL buttons  
or in the Phone Directory (memory match function; see page 55).  
the ringer sound changes to a higher tone if the call matches the number VIP  
stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory  
match function; see page 55).  
To turn the ringer off  
Set the RING switch on the bottom to OFF.  
“[RINGER OFF]” appears on the display.  
The cordless handset wont ring. You can still make  
calls, and also receive calls if another telephone  
connected to the same line rings to inform you on  
incoming calls. You can also receive an intercom call.  
RING sw itch  
36US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving calls w ith the base phone  
When you hear the phone ring, pick up  
the handset or press (SPEAKERPHONE) on  
the base phone.  
(CALL WAITING/ FLASH)  
(VOLUME)  
“TALK” or “SPEAKERPHONE” appears  
on the display and the display also shows  
the talk time in hours, minutes and  
seconds.  
When youre done talking, replace the  
handset in the cradle or press  
(SPEAKERPHONE) again.  
To obtain the best speakerphone  
performance, see page 32.  
(HOLD)  
(SPEAKERPHONE)  
Additional tasks  
To  
Do this  
Adjust the handset or  
speakerphone volume  
During phone conversation, press (VOLUME)(+)  
or (-).  
There are 3 steps for the handset volume level, and  
7 steps for the speakerphone volume level.  
Put a call on hold  
Press (HOLD). “HOLD” appears on the display.  
Press (HOLD), (SPEAKERPHONE), or pick up the  
handset from the base phone to resume the  
conversation.  
Switch to another call  
(“call waiting” service*)  
Press (CALL WAITING/ FLASH).  
Press (CALL WAITING/ FLASH) again to return to the  
first caller.  
Adjust the ringer volume  
of the base phone  
Press (VOLUME)(+) or (-). The ringer volume can  
be adjusted to three different levels: high, low, and  
“OFF”. If the ringer is set to “OFF”, “[RINGER  
OFF]” will appear on the display.  
* You need to subscribe to the service from your telephone company.  
co n t in u e d  
Basics 37US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Re ce ivin g ca lls (co n t in u e d )  
Notes  
Even when you set “RINGER VOL” on the base phone to “OFF”, the  
cordless handset will ring when the RING switch on the cordless handset is  
set to ON.  
If there is an incoming call during intercom conversation, intercom call will  
be disconnected, and both the base phone and the cordless handset will ring.  
Tips  
To inform you of an incoming call, the display shows “** RINGING **”  
even when you set “RINGER VOL” on the base phone to “OFF”.  
You can switch between phone conversations via the handset and those via  
the speakerphone, simply by picking up the handset while talking over the  
speakerphone, or by pressing (SPEAKERPHONE) while talking over the  
handset.  
38US Basics  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Te le p h o n e Fe a t u re s  
On e -t o u ch d ia lin g  
You can dial with one touch of a key by storing a phone number on a  
one-touch dialing button.  
St o rin g p h o n e n u m b e rs a n d n a m e s  
Example: to store “SONY123-  
4567”.  
1
2
Press (PROGRAM).  
Turn  
Press  
HANDSET MENU  
GO BACK  
PHONE DIRECTORY  
ONE-TOUCH DIAL  
QUICK TALK  
Turn Jog Dial to choose “ONE-  
TOUCH DIAL”, and then press  
Jog Dial.  
(TALK)  
(REDIAL/PAUSE)  
ONE-TOUCH DIAL  
GO BACK  
(LONG DIST. SAVER)  
(ERASE)  
ONE-TOUCH A  
ONE-TOUCH B  
ONE-TOUCH C  
ONE-TOUCH  
DIAL buttons  
3
Turn Jog Dial to choose “ONE-  
TOUCH A” to “ONE-TOUCH  
C”, and then press Jog Dial.  
co n t in u e d  
Telephone Features 39US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
On e -t o u ch d ia lin g (co n t in u e d )  
4
Enter the name by turning Jog Dial.  
You can enter up to 15 characters.  
ENTER NAME  
SONY_  
Turn Jog Dial until the desired character is  
selected, and then press Jog Dial.  
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
Each press of Jog Dial after choosing “[SWITCH]” switches the characters  
from upper case letters t lower case letters t numbers and symbols.  
ENTER NAME  
ENTER NAME  
ENTER NAME  
_
_
_
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
abcdefghijklmnop  
qrstuvwxyz  
SWITCH NUMBER  
0123456789"#$&'(  
)*+,-./:;  
SWITCH NUMBER  
Enter successive characters in the same way.  
To enter a “space”, turn Jog Dial to choose  
“[p]”, and then press Jog Dial.  
5
6
Turn Jog Dial to choose “[NUMBER]”, and then  
press Jog Dial.  
SONY  
ENTER NUMBERS  
_
“ENTER NUMBERS” appears on the display.  
0123456789*#  
F P VIP PGM  
Enter the phone number by turning Jog Dial.  
You can enter up to 20 digits, including a tone  
and a pause, each of which is counted as one  
digit.  
SONY  
1234567_  
0123456789*#  
F P VIP PGM  
Turn Jog Dial until the desired number is  
selected, and then press Jog Dial.  
Icon  
[F]  
Meaning  
SONY  
Flash can be entered.  
Pause can be entered.  
[P]  
1234567_  
[VIP]  
If [VIP] has been selected, “9will appear  
to the right of the displayed name. The  
ring type will change when calls are  
received from VIP registered numbers.  
0123456789*#  
F P VIP PGM  
40US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enter successive numbers in the same way.  
When the phone number of 16 digits or more  
has been entered, the phone number appears in  
two lines.  
SONY  
1234567890123456  
12_  
0123456789*#  
F P VIP PGM  
7
Turn Jog Dial to choose “[PGM]”, and then  
press Jog Dial.  
You hear a long confirmation beep, and the  
name and the number are stored.  
The display goes off.  
Notes  
Names cannot be entered using the dialing keys.  
Do not allow more than 20 seconds to elapse during the operation procedure.  
Tips  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Dial.  
If you have entered a wrong name or number in step 4 or 6, turn Jog Dial to  
choose “[P]” then press Jog Dial or press (ERASE) to erase it. Then enter the  
correct name or number.  
You may press (PROGRAM) instead of doing steps 5 and 7.  
Phone numbers can be entered using the dialing keys in step 6.  
To store a number to be dialed via Private Branch Exchange  
(PBX)  
Before entering a phone number in step 6 on page 40, do as follows:  
1 Enter the outside line access digit (e.g., 9).  
2 Turn Jog Dial to choose “[P]” and then press Jog Dial, or  
press (REDIAL/PAUSE).  
Ch a n g in g a st o re d n a m e a n d /o r p h o n e n u m b e r  
1 Display the name you want to change by doing  
ENTER NAME  
steps 1 to 3 on page 39.  
The cursor is at the right of the name.  
SONY_  
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
2 Turn Jog Dial to choose “[P]”, then press Jog  
Dial to erase the characters, and enter the new  
name.  
If you want to change only the number, skip this  
step.  
co n t in u e d  
Telephone Features 41US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
On e -t o u ch d ia lin g (co n t in u e d )  
3 Turn Jog Dial to choose “[NUMBER]”, and then  
press Jog Dial.  
SONY  
The cursor is at the right of the phone number.  
1234567_  
0123456789*#  
F P VIP PGM  
4 Turn Jog Dial to choose “[P]”, then press Jog  
Dial to erase the number, and enter the new  
number.  
If you dont want to change the number, skip  
this step.  
5 Turn Jog Dial to choose “[PGM]”, and then  
press Jog Dial.  
You hear a long confirmation beep and the  
name and/ or the number is changed.  
Note  
The stored record with name and number can be replaced with a new name and  
number but it is not possible to erase the whole entry at one time.  
Tips  
Single character and number can be erased by pressing (ERASE) in steps 2  
and 4.  
You may press (PROGRAM) instead of doing steps 3 and 5.  
Ma kin g ca lls w it h o n e -t o u ch d ia lin g  
1 Press (TALK) or (LONG DIST. SAVER) and wait until “TALK”  
appears on the display.  
2 Press one of the ONE-TOUCH DIAL buttons ((A) to (C)).  
The phone number stored on the one-touch dialing button  
will appear on the display and will be dialed.  
To check the phone number before one-touch dialing  
While the cordless handset is not in use, press one of the ONE-TOUCH  
DIAL buttons ((A) to (C)).  
The number stored on the button appears on the display for 20  
seconds. To dial the number, press (TALK) while the number is  
displayed.  
42US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ph o n e Dire ct o ry  
You can dial a number by scrolling through the Phone Directory.  
Both the base phone and the cordless handset can each store up to 50  
separate numbers.  
St o rin g p h o n e n u m b e rs a n d n a m e s  
1
Press (PROGRAM).  
Turn  
Press  
(Cordless handset)  
HANDSET MENU  
GO BACK  
PHONE DIRECTORY  
ONE-TOUCH DIAL  
QUICK TALK  
If “PHONE DIRECTORY” is  
not selected, turn Jog Dial to  
select it.  
2
3
Press Jog Dial. (If youre at the  
base phone, press Jog Button  
(ENTER).)  
“ENTER NAME” appears on  
the display.  
ENTER NAME  
_
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
Enter the name and the phone  
number by doing steps 4 to 7 on  
pages 40 to 41.  
Note  
If you try to save a 51st phone number, you will hear five short error beeps and  
“THE MEMORY IS FULL.” will be displayed. You cannot store the phone  
number. To store another phone number, erase one of the stored phone  
numbers (see page 45).  
co n t in u e d  
Telephone Features 43US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ph o n e Dire ct o ry (co n t in u e d )  
Ch a n g in g a st o re d n a m e a n d /o r p h o n e  
n u m b e r  
1 Display the name you want to change by doing  
BROWN JOHN  
steps 1 to 3 on pages 46 to 47.  
SONY  
SMITH JOHN  
SALINGER GREG  
WAGNER ANTHONY  
2 Press Jog Dial. (If youre at the base phone, press  
GO BACK  
Jog Button (ENTER).)  
DIAL  
LONG DISTANCE  
EDIT  
ERASE DIRECTORY  
3 Turn Jog Dial to choose “EDIT”, and then press  
ENTER NAME  
Jog Dial (or Jog Button (ENTER)).  
The cursor is at the right of the name.  
SONY_  
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
4 Change the name and/ or the phone number by  
doing steps 2 to 5 on pages 41 to 42.  
44US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Era sin g a m e m o ry lo ca t io n  
To erase the phone number one by one  
1 Display the name you want to erase by doing  
BROWN JOHN  
steps 1 to 3 on pages 46 to 47.  
SONY  
SMITH JOHN  
SALINGER GREG  
WAGNER ANTHONY  
2 Press Jog Dial. (If youre at the base phone, press  
GO BACK  
Jog Button (ENTER).)  
DIAL  
LONG DISTANCE  
EDIT  
ERASE DIRECTORY  
3 Turn Jog Dial to choose “ERASE DIRECTORY”,  
and then press Jog Dial (or Jog Button  
(ENTER)).  
ERASE DIRECTORY  
GO BACK  
NO  
YES  
4 Turn Jog Dial to choose “YES”, and then press  
Jog Dial (or Jog Button (ENTER)).  
You hear a long confirmation beep and the  
memory location is erased.  
co n t in u e d  
Telephone Features 45US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ph o n e Dire ct o ry (co n t in u e d )  
To erase the entire memory at once  
1 Press (PROGRAM).  
2 Turn Jog Dial to choose “MEMORY  
MEMORY MANAGE  
GO BACK  
MANAGE”, and then press Jog Dial. (If youre  
at the base phone, press Jog Button (ENTER).)  
SEND ALL DIR  
ERASE ALL CID  
ERASE ALL RDL  
3 Turn Jog Dial to choose “ERASE ALL DIR”,  
ERASE ALL DIR?  
GO BACK  
and then press Jog Dial (or Jog Button (ENTER)).  
NO  
ERASE DIRECTORY  
4 Turn Jog Dial to choose “ERASE DIRECTORY”,  
and then press Jog Dial (or Jog Button (ENTER)).  
You hear a long confirmation beep and the  
entire memory is erased.  
Ma kin g ca lls fro m t h e Ph o n e Dire ct o ry  
Turn  
Press  
1
Press Jog Dial. (If youre at the  
base phone, press Jog Button  
(ENTER).)  
“PHONE DIRECTORY”  
appears on the display.  
PHONE DIRECTORY  
CALLER ID  
ABC  
DEF  
GHI  
(TALK)  
(LONG DIST. SAVER)  
(PROGRAM)  
46US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2
3
Turn Jog Dial to select an alphabet group  
([ABC], [DEF]...) which includes the initial  
character of the name you want to search for,  
and then press Jog Dial (or Jog Button  
(ENTER)).  
PHONE DIRECTORY  
PQRS  
TUV  
WXYZ  
etc  
If a numbers or a symbol is the initial character,  
select the “[etc]” group.  
Select the name you want to call by turning Jog  
Dial.  
BROWN JOHN  
SONY  
SMITH JOHN  
SALINGER GREG  
WAGNER ANTHONY  
4
5
Press Jog Dial (or Jog Button (ENTER)).  
GO BACK  
DIAL  
LONG DISTANCE  
EDIT  
ERASE DIRECTORY  
Turn Jog Dial to choose “DIAL” or “LONG  
DISTANCE”, and then press Jog Dial (or Jog  
Button (ENTER)).  
The phone number will be dialed.  
Note  
When the Long Distance Saver function is set to “ACTIVE”, “LONG  
DISTANCE” can be selected in step 4 (see page 20).  
Tips  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Dial. (If youre at the base phone, press Jog Button (ENTER).)  
When you select “[CALLER ID]” in step 1, you can switch to display the  
Caller ID list (see page 56).  
If there is no data recorded in the selected alphabet group in step 2, the data  
memory of the next following group will be displayed.  
You may press (TALK) or (LONG DIST. SAVER) on the cordless handset (If  
youre at the base phone, pick up the handset from the base phone or press  
(SPEAKERPHONE) or (LONG DIST. SAVER)) to make a call instead of doing  
steps 4 and 5.  
co n t in u e d  
Telephone Features 47US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ph o n e Dire ct o ry (co n t in u e d )  
Tra n sfe rrin g t h e Ph o n e Dire ct o ry m e m o ry  
The Phone Directory memory can be transferred one by one or all at  
once (with a maximum of 50 numbers) from the cordless handset to  
the base phone and from the base phone to the cordless handset.  
To transfer one phone number from the Phone Directory  
1 Display the name you want to transfer by doing  
BROWN JOHN  
steps 1 to 3 on pages 46 to 47.  
SONY  
SMITH JOHN  
SALINGER GREG  
WAGNER ANTHONY  
2 Press Jog Dial. (If youre at the base phone, press  
Jog Button (ENTER).)  
GO BACK  
DIAL  
LONG DISTANCE  
EDIT  
ERASE DIRECTORY  
3 Turn Jog Dial to choose “SEND DIRECTORY”,  
and then press Jog Dial (or Jog Button  
(ENTER)).  
You hear a long confirmation beep and the  
memory is transferred.  
To transfer all phone numbers from the Phone Directory  
The Phone Directory receiving the transfer will be totally overwritten.  
1 Press (PROGRAM).  
2 Turn Jog Dial to choose “MEMORY  
MEMORY MANAGE  
GO BACK  
MANAGE”, and then press Jog Dial. (If youre  
at the base phone, press Jog Button (ENTER).)  
SEND ALL DIR  
ERASE ALL CID  
ERASE ALL RDL  
48US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3 Press Jog Dial again (or Jog Button (ENTER)).  
(Cordless handset)  
SEND ALL DIR?  
GO BACK  
NO  
SEND DIRECTORY  
(BASE OVERWRITE)  
4 Turn Jog Dial to choose “SEND DIRECTORY”,  
and then press Jog Dial (or Jog Button  
(ENTER)).  
“SENDING…” appears on the display during  
the transfer.  
You hear a long confirmation beep and the  
entire memory is transferred.  
Notes  
If there are already 50 numbers stored in the Phone Directory receiving the  
transferred number one by one from the other Phone Directory, “CORDLESS  
HANDSET MEMORY IS FULL.” or “BASEPHONE MEMORY IS FULL.”  
will appear on the display and five short error beeps will be heard to indicate  
that the transfer was unsuccessful. To make the transfer possible, erase one of  
the stored phone numbers existing in the Phone Directory (see page 45).  
If the transfer is unsuccessful, “SEND TO CORDLESS HANDSET  
FAILED.” or “SEND TO BASEPHONE FAILED.” will appear on the  
display, and five short error beeps will be heard. Move the cordless handset  
closer to the base phone, and then start over the procedure.  
Telephone Features 49US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sw it ch in g t h e p h o n e s d u rin g a ca ll  
You can easily switch between the cordless handset and the base  
phone without disconnecting the call.  
To sw it ch fro m t h e b a se p h o n e t o t h e  
co rd le ss h a n d se t  
1
Press (HOLD) on the base  
phone.  
The call is on hold and “HOLD”  
appears on the display.  
2
Pick up the cordless handset  
from the charger (When Quick  
talk is set to “USE”; see page 36)  
or press (TALK) or (HOLD) on  
the cordless handset.  
(SPEAKERPHONE)  
You can continue talking to the  
caller through the cordless  
handset.  
To sw it ch fro m t h e co rd le ss h a n d se t t o t h e  
b a se p h o n e  
1
Press (HOLD) on the cordless  
handset.  
The call is on hold and “HOLD”  
appears on the display.  
2
Pick up the handset from the  
base phone or press  
(SPEAKERPHONE) or (HOLD)  
on the base phone.  
(TALK)  
You can continue talking to the  
caller through the base phone.  
50US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ta lkin g b e t w e e n t h e p h o n e s  
(In t e rco m )  
You can talk between the base phone and the cordless handset. You  
can start the intercom from either phone.  
To t a lk fro m t h e co rd le ss  
h a n d se t t o t h e b a se p h o n e  
Press (INTERCOM).  
The base phone and cordless handset  
ring and “** PAGING **” appears  
on the display.  
When a person at the base phone picks  
up the handset from the base phone or  
presses (SPEAKERPHONE) or  
(INTERCOM), you can talk with each  
other.  
(OFF)  
“INTERCOM” appears on the display.  
(TALK)  
When you are done talking  
Replace the cordless handset on the  
charger or press (OFF) on the cordless  
handset.  
If no one answ ers the phone  
Press (INTERCOM) again.  
co n t in u e d  
Telephone Features 51US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ta lkin g b e t w e e n t h e p h o n e s (In t e rco m ) (co n t in u e d )  
To t a lk fro m t h e b a se  
p h o n e t o t h e co rd le ss  
h a n d se t  
Press (INTERCOM).  
The base phone and cordless handset  
ring and “** PAGING **” appears  
on the display.  
When a person at the cordless handset  
picks up the cordless handset from the  
charger (When Quick talk is set to  
“USE”; see page 36) or presses (TALK)  
or (INTERCOM), you can talk with  
each other.  
“INTERCOM” appears on the display.  
(SPEAKERPHONE)  
When you are done talking  
Replace the handset in the cradle or  
press (SPEAKERPHONE) on the base  
phone.  
If no one answ ers the phone  
Press (INTERCOM) again.  
Notes  
If there is an incoming call during intercom conversation, intercom call will  
be disconnected, and both the base phone and the cordless handset will ring.  
While talking with an outside caller via the base phone or cordless handset,  
you cannot make an intercom call. If you press (INTERCOM) on the cordless  
handset, “BASEPHONE IN USE” appears on the display and you will hear  
a busy tone.  
Tip  
You can receive an intercom call on the base phone or the cordless handset even  
when “RINGER VOL” on the base phone is set to “OFF”, or the RING switch  
on the cordless handset is set to OFF. The phone will ring at a low level.  
52US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Tra n sfe rrin g a ca ll  
You can transfer a call between the cordless handset and base phone  
without disconnecting the call.  
To t ra n sfe r fro m t h e b a se p h o n e t o t h e  
co rd le ss h a n d se t  
1
Press (INTERCOM) to page the  
cordless handset.  
The call is put on hold on the  
base phone and the cordless  
handset rings.  
** PAGING **” appears on  
the display of both the base  
phone and cordless handset.  
2
Pick up the cordless handset  
from the charger (When Quick  
talk is set to “USE”; see page 36)  
or press (TALK) or (INTERCOM)  
on the cordless handset.  
(SPEAKERPHONE)  
“INTERCOM” appears on the  
display of both the cordless  
handset and base phone.  
You can talk between the base  
phone and the cordless handset.  
3
To talk to the caller with the  
cordless handset, replace the  
handset in the cradle or press  
(SPEAKERPHONE) on the base  
phone.  
(TALK)  
“TALK” appears on the display  
of the cordless handset.  
If no one answ ers the phone  
Press (INTERCOM) again.  
Tips  
You can receive an intercom call on the cordless handset even when the  
RING switch is set to OFF. The cordless handset will ring at a low level.  
If you have accidentally pressed (HOLD) in step 1, just press (INTERCOM)  
and you will get the same result as by pressing (INTERCOM) only.  
co n t in u e d  
Telephone Features 53US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Tra n sfe rrin g a ca ll (co n t in u e d )  
To t ra n sfe r fro m t h e co rd le ss h a n d se t t o t h e  
b a se p h o n e  
1
Press (INTERCOM) to page the  
base phone.  
The call is put on hold on the  
cordless handset and the base  
phone rings. “** PAGING **”  
appears on the display of both  
the cordless handset and base  
phone.  
(OFF)  
2
Pick up the handset from the  
base phone or press  
(SPEAKERPHONE) or  
(INTERCOM) on the base phone.  
“INTERCOM” appears on the  
display of both the base phone  
and cordless handset.  
You can talk between the  
cordless handset and the base  
phone.  
3
To talk to the caller with the  
base phone, replace the cordless  
handset on the charger or press  
(OFF) on the cordless handset.  
(INTERCOM)  
“TALK” or “SPEAKERPHONE”  
appears on the display of the  
base phone.  
(SPEAKERPHONE)  
If no one answ ers the phone  
Press (INTERCOM) again.  
Tip  
You can receive an intercom call on the base phone even when “RINGER  
VOL” on the base phone is set to “OFF”. The base phone will ring at a low  
level.  
54US  
Telephone Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ca lle r ID Fe a t u re s  
Un d e rst a n d in g t h e Ca lle r ID se rvice  
Caller ID allows the callers phone number to be shown on the display before you  
answer the call. In order to use this feature, you must first subscribe to Caller ID  
service. The name of this service may vary depending on your telephone company.  
To use this feature, be sure to enter the area code (see page 13).  
Wh e n yo u re ce ive a ca ll  
The phone number appears on the display with the date and time as shown in the  
following example.  
If your Caller ID service includes the caller name service or if the phone number  
stored in the one-touch dialing, or the Phone Directory matches with the Caller ID  
data phone number, the callers name also appears on the display (up to 15 letters).  
The caller’s name will appear by the name stored in the one-touch dialing or Phone  
Directory if you receive a call from a phone number which is stored on one of the  
ONE-TOUCH DIAL buttons or in the Phone Directory.  
NEW 01  
Callers name  
SMITH JOHN  
Callers phone number  
1-201-123-4567  
7.04 4:53PM  
The date and time received  
When you answer the call, the Caller ID display changes to the “TALK” or  
“SPEAKERPHONE” display.  
Notes  
-
The caller’s phone number and/ or name will not appear in the following cases:  
“OUT OF AREA”: when the call is made through a telephone company which does not offer  
Caller ID service (including international calls).  
-
“PRIVATE”: when the call is “blocked”. For privacy reasons, many states allow callers the  
option to prevent his or her telephone data from being displayed on the other partys Caller  
ID display.  
If the call is from an office which uses multiple lines, the displayed phone number may not  
match the number you use to call the extension.  
About the memory match function  
The name stored in the one-touch dialing or Phone Directory will appear on the  
display if you receive a call from a phone number which is stored on one of the ONE-  
TOUCH DIAL buttons (see page 39) or in the Phone Directory (see page 43).  
In addition, the ringer sound will change to a higher tone from the second ring and  
9will appear to the right of the displayed name if you receive a call from a VIP  
registered phone number on the base phone or the cordless handset.  
Note  
The memory match function does not work with “OUT OF AREA” or “PRIVATE” calls; and it  
may not work with calls made from an office which uses multiple lines because the number does  
not always match the one you stored in this phone.  
55US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Lo o kin g a t t h e Ca lle r ID list  
The phone stores the data of the last 100 calls received including “OUT  
OF AREA” and “PRIVATE” calls. It keeps track of all calls received;  
even if they were not answered.  
Vie w in g t h e Ca lle r ID list  
You can look through the Caller ID list on both the base phone and the  
cordless handset to check the phone number and/ or name of the calls  
received.  
1
Turn Jog Dial.  
Turn  
Press  
The display shows the number  
of “NEW CALLS” (calls which  
you have not viewed) and  
“OLD CALLS” (calls which you  
have viewed) calls.  
CALLER ID  
NEW CALLS 08  
OLD CALLS 12  
2
Turn Jog Dial down to display  
older data or up to display  
newer data.  
Notes  
If a 101st call is received, the oldest data is automatically erased.  
When you have checked all data, “END OF LIST” appears.  
NEW CALL lamp  
Tip  
If there is a “NEW” data, the NEW CALL lamp of  
the base phone flashes.  
The number of “NEW CALLS” can be confirmed  
with the standby mode display of the base phone.  
56US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Era sin g d a t a fro m t h e Ca lle r ID list  
Old data will be erased automatically when a 101st call comes in, but  
you can also manually erase unnecessary data one by one or erase the  
entire list.  
To erase the phone number one by one  
1 Display the phone number you want to erase  
NEW 01  
from the Caller ID list (see page 56).  
SMITH JOHN  
1-201-123-4567  
7.04 4:53PM  
2 Press Jog Dial. (If youre at the base phone, press  
GO BACK  
Jog Button (ENTER).)  
DIAL  
LONG DISTANCE  
PROGRAM  
ERASE CALLER ID  
3 Turn Jog Dial to choose “ERASE CALLER ID”,  
and then press Jog Dial (or Jog Button  
(ENTER)).  
ERASE CALLER ID  
GO BACK  
NO  
YES  
4 Turn Jog Dial to choose “YES”, and then press  
Jog Dial (or Jog Button (ENTER)).  
You hear a long confirmation beep and the data  
is erased.  
Note  
Do not allow more than 20 seconds to elapse during the operation procedure.  
Tip  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Dial. (If youre at the base phone, press Jog Button (ENTER).)  
co n t in u e d  
57US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Lo o kin g a t t h e Ca lle r ID list (co n t in u e d )  
To erase the entire list at once  
Entire Caller ID list deletion can only be made on the base phone.  
Note that Caller ID data in the list that has not been viewed will also  
be erased.  
1 Press (PROGRAM).  
2 Turn Jog Dial to choose “MEMORY  
MEMORY MANAGE  
GO BACK  
MANAGE”, and then press Jog Button  
(ENTER).  
SEND ALL DIR  
ERASE ALL CID  
ERASE ALL RDL  
3 Turn Jog Dial to choose “ERASE ALL CID”,  
ERASE ALL CID?  
GO BACK  
and then press Jog Button (ENTER).  
NO  
ERASE CALLER ID  
4 Turn Jog Dial to choose “ERASE CALLER ID”,  
and then press Jog Button (ENTER).  
You hear a long confirmation beep and the  
entire list is erased.  
Note  
Do not allow more than 20 seconds to elapse during the operation procedure.  
Tip  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Button (ENTER).  
58US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usin g t h e Ca lle r ID list  
By using the Caller ID list, you can call back a phone number from the  
Caller ID list easily, or store numbers from the Caller ID list into the  
Phone Directory.  
Ca llin g b a ck a n u m b e r fro m t h e Ca lle r ID list  
1
2
3
Display the phone number you  
want to call from the Caller ID  
list (see page 56).  
Turn  
Press  
NEW 01  
SMITH JOHN  
1-201-123-4567  
7.04 4:53PM  
(TALK)  
Press Jog Dial. (If youre at the  
base phone, press Jog Button  
(ENTER).)  
(LONG DIST. SAVER)  
GO BACK  
DIAL  
LONG DISTANCE  
PROGRAM  
ERASE CALLER ID  
Turn Jog Dial to choose “DIAL”  
or “LONG DISTANCE”, and  
then press Jog Dial (or Jog  
Button (ENTER)).  
The phone automatically dials  
the displayed number.  
co n t in u e d  
59US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Usin g t h e Ca lle r ID list (co n t in u e d )  
Notes  
When the Long Distance Saver function is set to “ACTIVE”, “LONG  
DISTANCE” can be selected in step 2 (see page 20).  
If the area code is not entered, “PLEASE ENTER AREA CODE” will appear  
on the display, and you will not be able to call back. Enter the area code (see  
page 13).  
Do not allow more than 20 seconds to elapse during the operation procedure.  
If the number displayed in step 1 is not the one you should call back, you can  
change the number of digits of the phone number as described on page 62.  
If the phone is connected to a Private Branch Exchange (PBX), you may not  
be able to call back from the Caller ID list because an outside line access digit  
is necessary.  
Tips  
You may press (TALK) or (LONG DIST. SAVER) on the cordless handset (If  
youre at the base phone, pick up the handset from the base phone or press  
(SPEAKERPHONE) or (LONG DIST. SAVER)) to make a call instead of doing  
steps 2 and 3.  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Dial. (If youre at the base phone, press Jog Button (ENTER).)  
60US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
St o rin g a n u m b e r o f t h e Ca lle r ID list in t o  
t h e Ph o n e Dire ct o ry  
1 Display the name and phone number you want  
NEW 01  
to store from the Caller ID list (see page 56).  
SMITH JOHN  
1-201-123-4567  
7.04 4:53PM  
2 Confirm the number and press Jog Dial. (If  
youre at the base phone, press Jog Button  
(ENTER).)  
GO BACK  
DIAL  
LONG DISTANCE  
PROGRAM  
ERASE CALLER ID  
3 Turn Jog Dial to choose “PROGRAM”, and then  
ENTER NAME  
press Jog Dial (or Jog Button (ENTER)).  
The cursor is at the right of the name.  
SMITH JOHN_  
ABCDEFGHIJKLMNOP  
QRSTUVWXYZ  
SWITCH NUMBER  
Enter or change the name, if necessary (see page  
41).  
4 Turn Jog Dial to choose “[NUMBER]”, and then  
press Jog Dial (or Jog Button (ENTER)).  
SMITH JOHN  
The cursor is at the right of the phone number.  
Enter or change the phone number, if necessary  
(see page 42).  
12011234567_  
0123456789*#  
F P VIP PGM  
5 Turn Jog Dial to choose “[PGM]”, and then  
press Jog Dial (or Jog Button (ENTER)).  
You hear a long confirmation beep and the  
name and number are stored.  
co n t in u e d  
61US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Usin g t h e Ca lle r ID list (co n t in u e d )  
Notes  
If the area code is not entered, “PLEASE ENTER AREA CODE” will appear  
on the display, and you will not be able to store into the Phone Directory.  
Enter the area code (see page 13).  
Do not allow more than 20 seconds to elapse during the operation procedure.  
If the number displayed in step 1 is not the one you should store, you can  
change the number of digits of the phone number as described below.  
If the phone is connected to a Private Branch Exchange (PBX), you may need  
to add an outside line access digit.  
Tips  
When you select “[GO BACK]”, you can return to the previous set display by  
pressing Jog Dial. (If youre at the base phone, press Jog Button (ENTER).)  
You may press (PROGRAM) instead of doing steps 4 and 5.  
To ch a n g e t h e n u m b e r o f d ig it s o f t h e p h o n e  
n u m b e r  
If the number of digits of the phone number in the Caller ID list is  
different from the actual phone number, you need to adjust the  
number of digits of the phone number to call back or store into the  
Phone Directory.  
1 While the phone number from the Caller ID list is displayed,  
press (#) repeatedly until the phone number with the  
correct number of digits appears on the display.  
Each time you press (#), the number of digits changes as  
follows:  
When the home area code and the local area code do  
not match  
NEW 01  
NEW 01  
SMITH JOHN  
SMITH JOHN  
1-201-123-4567  
7.04 4:53PM  
201-123-4567  
7.04 4:53PM  
NEW 01  
NEW 01  
SMITH JOHN  
123-4567  
7.04 4:53PM  
SMITH JOHN  
1-123-4567  
7.04 4:53PM  
62US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
When the home area code matches  
NEW 01  
NEW 01  
SMITH JOHN  
123-4567  
7.04 4:53PM  
SMITH JOHN  
1-201-123-4567  
7.04 4:53PM  
NEW 01  
NEW 01  
SMITH JOHN  
1-123-4567  
7.04 4:53PM  
SMITH JOHN  
201-123-4567  
7.04 4:53PM  
When the local area code matches  
NEW 01  
NEW 01  
SMITH JOHN  
SMITH JOHN  
1-123-4567  
7.04 4:53PM  
201-123-4567  
7.04 4:53PM  
NEW 01  
NEW 01  
SMITH JOHN  
SMITH JOHN  
123-4567  
7.04 4:53PM  
1-201-123-4567  
7.04 4:53PM  
2 Continue the operation to call or store the phone number  
with the correct number of digits (pages 59 and 61).  
Notes  
You need to adjust the number of digits each time you call back from the  
Caller ID list as the changes to the Caller ID data is not stored in memory.  
You may not be able to change the number of digits depending on the Caller  
ID data.  
63US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usin g “ Ca lle r ID w it h ca ll w a it in g ”  
se rvice  
This telephone is compatible with the “Caller ID with call waiting”  
service. Make sure that your telephone company offers this service.  
Like the basic Caller ID service, you need to subscribe to “Caller ID  
with call waiting” in order to use this service.  
Even though you may have already subscribed to “Caller ID” and  
“call w aiting” as tw o separate services, you need to request a  
subscription to “Caller ID w ith call w aiting” as a single service.  
This is a new service that combines the two services.  
Even though you now have a “Caller ID w ith call w aiting”  
compatible phone, unless you subscribe to the combined “Caller ID  
w ith call w aiting” service, you w ill not be able to see the name  
and number of the second caller.  
When a new call comes in while you are talking, the callers name  
and/ or phone number of the new call appears on the display for about  
20 seconds.  
To sw itch to another caller  
1
2
To switch to the new caller,  
press (CALL WAITING/FLASH).  
To switch back to the first caller,  
press (CALL WAITING/FLASH)  
again.  
Tip  
When the “Caller ID with call waiting” service is set to “INACTIVE”, you  
cannot use this service even if you have subscribed to “Caller ID with call  
waiting” service (see page 17).  
64US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Usin g vo ice m a il se rvice  
If you subscribe to your telephone companys message service which  
includes this feature, the display will show that you have messages  
waiting to be retrieved.  
MESSAGES lamp  
(PROGRAM)  
If yo u h a ve m e ssa g e s  
“MESSAGES WAITING” appears on the  
display of both the cordless handset and  
base phone and the MESSAGES lamp on  
the base phone flashes.  
The display and the MESSAGES lamp will  
go off when you retrieve your messages.  
Jog  
Button  
(ENTER)  
Jog Dial  
Note  
You cannot use this feature, if you have not subscribed to your telephone  
companys message service.  
For details on the availability of this service, please ask your telephone  
company.  
Tip  
When the voice mail service is set to “INACTIVE”, the MESSAGES lamp does  
not function even if you have subscribed to voice mail service (see page 21).  
If the MESSAGES lamp remains flashing  
If this lamp does not go off (e.g. When you retrieve your messages  
with other phones), you can go off the lamp manually.  
To go off the MESSAGES lamp  
1 Press (PROGRAM).  
2 Turn Jog Dial to choose “BASE SETTINGS”,  
and then press Jog Button (ENTER).  
3 Turn Jog Dial to choose “MESSAGES LAMP”,  
MESSAGES LAMP  
GO BACK  
and then press Jog Button (ENTER).  
LIGHT-OFF  
RESET  
4 Press Jog Button (ENTER).  
The MESSAGES lamp on the base phone goes  
off, and you hear a long confirmation beep.  
co n t in u e d  
Caller ID Features  
65US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Usin g vo ice m a il se rvice (co n t in u e d )  
If you move or change your telephone company  
Message waiting signals are sent in one of two ways: FSK signaling or  
“stutter” signaling (Your telephone company can provide you with  
more information about your service).  
The first time this phone receives a voice mail message, it will set itself  
to the FSK service and will lock out the stutter service if your  
telephone company is in FSK service.  
When you move or change your telephone company, you need to  
perform the following procedure. The phone will returns to ready state  
for either FSK or stutter dial tone voice mail recognition.  
To reset this phone  
1 Perform steps 1 and 3 on page 65.  
MESSAGES LAMP  
LIGHT-OFF  
2 Turn Jog Dial to choose “RESET”, and then  
RESET  
press Jog Button (ENTER).  
You hear a long confirmation beep and the  
phone is reset.  
66US  
Caller ID Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ad d it io n a l In fo rm a t io n  
Mo u n t in g t h e b a se p h o n e o n a w a ll  
1
1
2
Reverse the hang-up tab.  
Hang-up tab  
Plug the telephone line cord to  
the LINE jack and the AC power  
adaptor to the DC IN 11V jack,  
and hook the cords. Use the  
shorter cord for mounting.  
3
Attach the wall bracket to the  
center of the base phone.  
2
Align the f marks of the wall  
bracket with those of the base  
phone.  
AC pow er  
adaptor cord  
Telephone  
line cord  
4
5
Plug the telephone line cord to  
the telephone outlet, and hook  
the base phone to the wall plate.  
Plug the AC power adaptor to  
an AC outlet. Then raise the  
antenna so that it points  
towards the ceiling.  
3
4, 5  
1
2
Wall plate  
Telephone  
line cord  
Wall bracket  
AC outlet  
AC pow er  
adaptor  
Tip  
To remove the wall bracket, press the lower tabs.  
Additional Information 67US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ca rryin g t h e co rd le ss h a n d se t b y t h e  
b e lt clip  
You can hang the cordless handset on the belt by attaching the belt clip  
to the cordless handset.  
At t a ch in g t h e b e lt clip  
Press the belt clip to the cordless  
handset. Make sure that the side  
tabs click and go into the holes on  
the sides of the cordless handset.  
Note  
To prevent the cordless handset from dropping, make sure that each tab is  
completely inserted.  
De t a ch in g t h e b e lt clip  
While pressing the back of the belt  
clip, pull the sides one by one until  
the tabs come off from the holes.  
Note  
Remove the belt clip carefully to avoid breaking your fingernails.  
68US Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the headset  
You can talk on the cordless handset without using your hands by  
connecting a headset (optional) to the I (HEADSET) jack on the  
cordless handset.  
I (HEADSET)  
jack  
Additional Information 69US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
No t e s o n p o w e r so u rce s  
On battery pack  
For the customers in the USA  
• Store the battery pack at a  
temperature between 41°F (5°C) and  
95°F (35°C) for best performance.  
RECYCLING NICKEL-CADMIUM  
BATTERIES  
Nickel-Cadmium batteries  
are recyclable. You can help  
preserve our environment  
by returning your  
unwanted batteries to your  
nearest point for collection,  
recycling or proper  
• If you do not use the cordless handset  
for a long period of time, remove the  
battery pack after charging for more  
than 12 hours.  
disposal.  
Note: In some areas the disposal of nickel-  
cadmium batteries in household or  
business trash may be prohibited.  
On pow er failure  
During a power interruption, you  
cannot make or receive calls.  
RBRC (Rechargeable Battery Recycling  
Corporation) advises you about spent battery  
collection by the following phone number.  
Call toll free number: 1-800-822-8837  
(United States and Canada only)  
Caution: Do not handle damaged or leaking  
nickel-cadmium batteries.  
70US Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Ma in t e n a n ce  
• Clean the cabinets with a soft cloth  
slightly moistened with water or a  
mild detergent solution. Do not use  
any type of abrasive pad, scouring  
powder or solvent such as alcohol or  
benzine as they may damage the  
finish of the cabinet.  
• If the charge terminals of the charger  
and cordless handset are soiled, wipe  
them with a soft cloth.  
If you have any questions or problems  
concerning your phone, please consult  
your nearest Sony dealer.  
Additional Information 71US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Tro u b le sh o o t in g  
If youve experienced any of the following difficulties while using your  
phone, use this troubleshooting guide to help you remedy the problem.  
Should any problem persist, consult your nearest Sony dealer.  
Symptom  
Remedy  
You hear five short error  
Make sure you have set up the base phone correctly  
beeps when you press (TALK).  
(page 8).  
Move the cordless handset closer to the base phone.  
You hear no dial tone.  
Make sure the telephone line cord is securely  
connected to the telephone outlet.  
Make sure the battery is fully charged (page 11).  
Make sure the dialing mode is set correctly (page 10).  
The phone does not connect at  
all, even though the number  
you dial is correct.  
Make sure the dialed number is really the one you  
want to dial.  
The phone does not redial  
correctly.  
During phone conversation, press (VOLUME)(+) on  
the base phone to increase the speakerphone volume.  
You cannot hear anything from  
the speakerphone.  
Make sure that the Long Distance Saver function is set  
to “ACTIVE” (page 20).  
(LONG DIST. SAVER) does not  
function.  
Make sure that the registered access number is correct  
and if the service provider needs any registration  
beforehand.  
Even by pressing  
(LONG DIST. SAVER), the long  
distance call is not being made.  
Set the RING switch on the cordless handset to ON.  
The battery may be weak. Charge the battery for more  
than 12 hours (page 11).  
The cordless handset does not  
ring.  
Make sure you have set up the base phone correctly  
(page 8).  
Move the cordless handset closer to the base phone,  
and confirm a dial tone is heard by pressing (TALK)  
on the cordless handset.  
Press (VOLUME)(+) on the base phone to increase the  
ringer volume.  
Make sure the telephone line cord is securely  
connected to the telephone outlet.  
The base phone does not ring.  
72US Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Symptom  
Remedy  
Move the cordless handset closer to the base phone.  
Place the base phone away from noise sources  
(page 8).  
You hear interference during  
conversation.  
Place the base phone so that the antenna keeps away  
from metal products.  
This is the out-of-range alarm. Move the cordless  
handset closer to the base phone within 30 seconds.  
You hear a beep every second  
during a conversation and “ ”  
appears on the display.  
The battery is weak. Charge the battery for more than  
12 hours (page 11).  
You hear a beep twice per  
second and “BATTERY LOW”  
appears on the display.  
Make sure you follow the procedure for storing the  
number correctly (pages 39, 43).  
You hear five short error beeps  
and cannot store a number on a  
one-touch dial or in the Phone  
Directory.  
You have pressed a one-touch dialing button on  
which no phone number has been stored.  
You hear five short error beeps  
when you try to make a one-  
touch dial call.  
Store the correct number (pages 39, 43).  
One-touch dialing or Phone  
Directory dialing is incorrect.  
The battery may be week. Charge the battery for more  
than 12 hours (page 11).  
Move the cordless handset closer to the base phone.  
Place the base phone away from noise sources  
(page 8).  
The cordless handset does not  
ring when you use the intercom  
from the base phone, and the  
base phone does not ring when  
you use the intercom from the  
cordless handset.  
The base phone is being used to converse with an  
outside caller.  
When pressing (INTERCOM) on  
the cordless handset, you hear a  
busy tone and cannot make an  
intercom call.  
co n t in u e d  
Additional Information 73US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tro u b le sh o o t in g (co n t in u e d )  
Symptom  
Remedy  
The caller’s name and/ or  
phone number does not appear  
on the display.  
Make sure you have subscribed to Caller ID service.  
Caller ID service may not work when the phone is  
connected to a Private Branch Exchange (PBX).  
The call is made through company which does not  
offer Caller ID service. “OUT OF AREA” will appear  
on the display.  
The call was “blocked.” “PRIVATE” will appear on  
the display.  
You have answered the call while “** RINGING **”  
was displayed. Please answer the call after the second  
ringer sound.  
The caller’s name and/ or  
phone number does not  
appear on the display during  
call waiting.  
Make sure you have subscribed to “Caller ID with call  
waiting” service (page 64).  
Make sure the “Caller ID with call waiting” service is  
set to “ACTIVE” (page 17).  
Make sure nobody is talking with another phone on  
the same telephone line.  
You cannot dial the number  
from the Caller ID list.  
Make sure you entered your area code correctly  
(page 13).  
You may need to change the number of digits of the  
phone number (page 62).  
This function may not work when the phone is  
connected to a Private Branch Exchange (PBX).  
The memory match function  
does not work.  
If the call is from an office which uses multiple lines,  
the phone number may not match the number you  
put in the memory.  
If you have stored phone number with an outside line  
access digit on a one-touch dial or in the Phone  
Directory because the phone is connected to a Private  
Branch Exchange (PBX), the phone number will not  
match the Caller ID data.  
If you have stored phone number of less than 7 digits  
on a one-touch dial or in the Phone Directory, the  
phone number will not match the Caller ID data.  
You cannot use voice mail  
service.  
Make sure you have subscribed to voice mail service  
(page 65).  
The MESSAGES lamp does not  
function even if you have  
subscribed to voice mail  
service.  
If you move or change your telephone company, reset  
this phone (page 66).  
Make sure that the voice mail service is set to  
“ACTIVE” (page 21).  
74US Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Symptom  
Remedy  
The CHARGE lamp on the  
charger does not light up when  
you place the cordless handset  
to charge.  
• Wipe the charge terminals of the charger and the  
cordless handset with a soft cloth for better contact of  
the charge terminals.  
• Make sure the cordless handset is placed on the  
charger properly.  
• Make sure the cordless handset is placed on the  
charger with front side facing forward.  
• Use only the supplied AC-T107 AC power adaptor.  
The battery duration is short.  
• The battery pack was charged less than 12 hours (due  
to power failure, etc.).  
• The usage life of the battery has expired and needs  
replacement.  
• Use only the supplied AC-T107 AC power adaptor.  
Note  
If any of these remedies do not work in the base phone, unplug the AC power  
adaptor, and then plug it again. In the cordless handset, take the battery out,  
and then insert it again.  
co n t in u e d  
Additional Information 75US  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sp e cifica t io n s  
General  
Base phone  
Spread method  
Power source  
Direct-Sequence Spread-Spectrum  
Access method  
DC 11V from AC power adaptor  
AC-T107  
FDMA-TDD  
Dimensions  
Frequency band  
Approx. 175 x 60 x 214 mm (w/ h/ d),  
antenna excluded  
2.406-2.475 GHz  
Operating channel  
23 channels  
(approx. 7 x 2 38 x 8 12 inches)  
Antenna: Approx. 112 mm  
(approx. 4 12 inches)  
Mass  
Approx. 580 g  
(approx. 1 lb 4 oz), wall bracket excluded  
Dial signal  
Tone, 10 PPS (pulse) selectable  
Supplied accessories  
See page 7.  
Charger  
Power source  
DC 6V from AC power adaptor  
Dimensions  
Approx. 72.5 x 60 x 85 mm (w/ h/ d)  
(approx. 2 78 x 2 38 x 3 38 inches)  
Mass  
Cordless handset  
Power source  
Rechargeable battery pack BP-T24  
Battery life  
Standby: Approx. 6 days  
Talk:  
Approx. 6 hours  
Battery charging time  
Approx. 12 hours  
Dimensions  
Approx. 204 g (approx. 7.2 oz)  
Approx. 58 x 185.4 x 48 mm (w/ h/ d),  
antenna excluded  
Design and specifications are subject to  
change without notice.  
(approx. 2 38 x 7 38 x 1 1516 inches)  
Antenna: Approx. 72 mm  
(approx. 2 78 inches)  
Mass  
Approx. 260 g  
(approx. 9.2 oz), battery included  
76US Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
In d e x  
A
E, F, G  
Erasing  
Caller ID data 57  
phone numbers dialed  
34  
R
Adjusting volume  
cordless handset volume  
29, 36  
Receiving calls 35  
Redialing 33  
Ringer  
handset volume 32, 37  
RING switch 36  
speakerphone volume  
32, 37  
Area code 13  
Phone Directory  
45  
S
H
Setting up  
Headset 29, 35, 69  
Hold 29, 36  
base phone 8  
cordless handset 11  
B
Battery pack  
charging 11  
duration 12  
Home area code 13  
Setting up the phone  
services 17  
Speakerphone 32  
Storing Caller ID data in  
Phone Directory 61  
Switching phones during a  
call 50  
I, J, K  
Identifying the parts 24  
Intercom 51  
C
Call waiting service 29, 36  
Caller ID 55  
Caller ID list 56  
calling back 59  
memory match function  
55  
storing in Phone  
Directory 61  
Caller ID with call waiting  
17, 64  
Carrying the cordless  
handset by the belt clip 68  
L
Local area code 15  
Location, base phone 8  
Long Distance Saver  
function 19, 29  
T, U  
Talking between the  
phones 51  
Tone dialing  
dialing mode 10  
switching to 29  
M, N  
Making calls 28  
Memory match function  
55  
Mounting the base phone  
on a wall 67  
Transferring a call 53  
Troubleshooting 72  
Connection 9  
V, W, X, Y, Z  
Voice mail service 65  
Volume  
cordless handset 29, 36  
handset 32, 37  
speakerphone 32, 37  
D
O
Dialing mode  
choosing 10  
switching to the tone  
temporarily 29  
Directory  
One-touch dialing 39  
OUT OF AREA 55  
P, Q  
Package contents 7  
Phone Directory 43  
PRIVATE 55  
Phone Directory 43  
Pulse dialing 10  
77US  
Additional Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For the customers in the USA  
Be sure to save the receipt and attach it to your WARRANTY card when having  
your equipment repaired at an authorized Sony service center.  
For online product registration, please contact  
Sony Corporation Printed in Taiwan, R.O.C.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Sony CRT Television E240 User Manual
Sony DVD VCR Combo SLV D910B User Manual
Sony GPS Receiver P800 P900 User Manual
Sony Microcassette Recorder ICD SX56 User Manual
Sony Satellite TV System SAT A65 User Manual
Sony Tablet SVJ2021 User Manual
Sprint Nextel Games Play Multiplayer Games User Manual
Stanley Black Decker Portable Generator GTR20 User Manual
StarTechcom Computer Drive SAT3510U2F User Manual
TANDBERG Network Card D1320203 User Manual