BID SPECIFICATION
FOR
DLP PROJECTORS
MODEL NUMBER
VPD-LE100
INSTRUCTIONS:
REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND
PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST YOU IN
CLEARLY SPECIFYING THE SONY PRODUCT IDENTIFIED ABOVE, AND ENSURING
THAT THE BUYER IS WELL INFORMED OF THE HIGH STANDARD OF
PERFORMANCE THAT IS TO BE EXPECTED OF A SONY PRODUCT. THE
INFORMATION IN THIS DOCUMENT IS CURRENT AS OF JUNE 2002. PRODUCT
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
SONY ELECTRONICS INC.
DISPLAY PRODUCTS GROUP
1 SONY DRIVE, MD S3D9
PARK RIDGE, NJ 07656
TEL# (201)-930-1000, FAX# (201)-358-4303
Download from Www.Somanuals.com. All Manuals Search And Download.
720P (60Hz)
1035I (60 Hz)
1080I (50 and 60 Hz)
1080P (24 PsF)
VGA Computer Graphics (Modes 1, 2 and 3, 60 - 85 Hz)
VESA 800x600 Computer Graphics (56 - 85 Hz)
VESA 1024 x 768 Computer Graphics (43 – 85 Hz)
VESA 1152 x 864 Computer Graphics (70 – 75 Hz)
SUN 1152 x 900 Computer Graphics (65 – 76 Hz)
VESA 1280 x 1024 Computer Graphics (43 – 85 Hz)
VESA 1600 x 1200 Computer Graphics (60 - 75 Hz)
Mac 13” Computer Graphics
Mac 16” Computer Graphics
Mac 21” Computer Graphics
This device shall accept multi-scanning sources, with scan frequencies ranging
from 15 to 100 kHz Horizontally, and 40 to 120 Hz Vertically.
This device shall employ the use of a high performance interpolation circuit,
which regenerates a high-resolution sampling of the original signal by referring to
memorized waveform patterns to enhance image performance. This device shall
also employ the use of a 3-dimensional comb filter and 3-line filter for maximum
chrominance and luminance separation and to minimize dot interference and
cross color when viewing NTSC video sources.
This device shall have the ability to store and recall multiple memory presets for
various video and computer configurations.
4.0 User Interface / Controllability Information
Control of this device shall be accomplished through one of the following
methods:
Backlit, projector control panel
Wired / Wireless backlit projector remote control
Serial control jack for control by external control systems
Advanced serial control jack for control by external control systems
Advanced serial control jack for control by external signal switchers
All of these control methods shall be standard to the device, or available at an
additional charge if considered an optional accessory.
The projector control panel shall be recessed into the cabinet, and shall employ
the use of a backlight that activates when any button is pressed. The backlight
shall have a timeout function. The control panel shall activate multi-language on-
screen menus, which navigate the operator through setup and configuration of
Download from Www.Somanuals.com. All Manuals Search And Download.
the device. The device shall be addressable for control over multiple devices
from a single remote control.
The wired / wireless backlit projector remote control shall operate in the same
fashion as the projector control panel, and shall accommodate infrared wireless
operation, or operation via a standard mini-plug cable. An infrared extender shall
be available from the device manufacturer for operation of the device wirelessly
in a rear-screen or cabinet environment.
The serial control jack shall employ the use of a standardized device control
protocol that is commonly accepted and understood by control systems
manufacturers. This control jack shall accept unidirectional serial commands that
provide full control over the device.
The advanced serial control jack shall employ the use of a standardized device
control protocol that is commonly accepted and understood by control systems
manufacturers. This control jack shall accept and transmit bi-directional serial
commands that provide full control over the device, and provide
acknowledgement to the control system of the received command.
The advanced serial control jack for control by external signal switchers shall
employ the use of a standardized device control protocol that is commonly
accepted and understood by control and signal switching manufacturers, and
shall operate at distances greater than 1000 feet without regeneration from an
external device. This control jack shall accept and transmit bi-directional serial
commands that provide full control over the device, and provide
acknowledgement to the control system of the received command.
The following device functions shall be available for control:
Power On / off
Input Selection
Brightness / Contrast
Video Decoder Functions
Audio Volume
Memory Recall Functions
White Balance
Gain / Bias Control
Image Sizing
Image Positioning
Lens Power Zoom
Lens Power Shift
Lens Power Focus
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 Performance Specifications
This device shall employ the use of 3 Texas Instruments high-resolution 1.1-inch
DMD chips. This device shall provide a light output of 10,000 ANSI lumens, when
measured using a 1280 x 1024 native resolution signal.
This device shall include a standard power zoom / focus / shift lens, and other
lenses shall be available as options for a variety of short-throw and long-throw
applications.
This device shall have a minimum RGB resolution of 1280 by 1024 pixels and a
minimum video resolution of 600 TV lines.
An automatic dot-phase adjustment technology shall be employed to optimize the
display to the input source without user intervention.
This device shall employ the use of a flat-spectrum xenon lamp system, providing
for optimum balance between the red, green and blue color spectrum.
This device shall employ the use of a 2-3 pulldown technique for accurate and
detailed reproduction of film originating source material.
A 13-bit signal processing shall be employed for accurate, smooth reproduction
of color and grayscale images.
6.0 Dimensional Information
This device shall have maximum cabinet dimensions of 13.75 inches high by
28.63 inches wide and 37.38 inches deep.
This device shall not weigh more than 209 pounds.
7.0 Connectivity Information
This device shall provide for connection of 4 source devices simultaneously,
without employing the use of an external switching device. One of these
connections shall be a standard input on the device, with 3 available for custom
configuration. The standard connection shall include the following:
RGB Computer / Component Video / HDTV Video (Sync on Green, Composite,
or Separate Sync) on BNC Connectors
Optional Modules shall allow for the following connections:
RGB Computer / Component Video (Sync on Green, Composite, or Separate
Sync) on BNC Connectors
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio L/R on RCA (Phono) Connectors
RGB Computer / Component Video (Sync on Green, Composite, or Separate
Sync) on a 9 pin (D9) Connector
Audio L/R on RCA (Phono) Connectors
RGB Computer / Component Video (Sync on Green, Composite, or Separate
Sync) on a VGA (HD15) Connector with loop-through
Audio L/R on RCA (Phono) Connectors
Component Serial Digital Video on a BNC Connector with loop-through
Composite Video on a BNC Connector or Y/C Video on a 4 Pin DIN Connector,
both with loop-through
Audio L/R on RCA (Phono) Connectors
High Definition Serial Digital Video on a BNC Connector with loop-through
These optional modules shall be user-installable, without access to the inside of
the device, and shall also be installable in an optional external switching device
available from the device manufacturer.
This device shall include a 12V power output for providing power to external
devices.
8.0 Power Requirements
This device shall accept power from 220 to 240 VAC at either 50 or 60 Hz.
This device shall consume no more than 2800 watts.
This device shall emit no more than 9556 BTU.
Power to this device shall be supplied via a detachable standard power cord that
is readily available for replacement from local suppliers.
Download from Www.Somanuals.com. All Manuals Search And Download.
9.0 Safety Compliance Information
This device shall be fully compliant with the following standards:
UL 1950
cUL 950
FCC Class A
IC Class A
VCCI Class A
JEIDA
EN60 950
CE
C-Tick
10.0 Warranty Information
This device shall carry a 2-year manufacturer’s warranty, with a 90-day lamp warranty.
Authorized servicing dealers of the devices’ manufacturer shall perform warranty
service.
Download from Www.Somanuals.com. All Manuals Search And Download.
|