BGetting started
Playing Back Messages
When playing back a previously recorded message, start from Step 1. When
playing back a message you have just finished recording, start from Step 2-2.
Index to Parts and Controls
Identifying the front and rear panels of the unit
Step 1: Installing the Batteries
Searching forward/backward
during playback (Cue/Review)
• To search forward (cue): Keep V
pressed during playback and
Notes on batteries
1
Slide and open the battery
compartment lid.
IC Recorder
• Do not use manganese batteries for
this unit.
• Do not charge dry batteries.
• When you are not going to use the
unit for an extended period of time,
remove the batteries to prevent
damage from battery leakage and
corrosion.
release the key at the point you
wish to resume playback.
• To search backward (review):
Keep v pressed during playback
and release the key at the point you
wish to resume playback.
2
Insert two LR03 (size AAA)
alkaline batteries with correct
polarity, and close the lid.
Make sure to insert batteries
into the unit from the - end first.
Operating Instructions
Select the folder.
1
Follow the step 2 in “Recording Messages”.
Owner’s Record
The model number is located at the rear and the serial number is located inside the battery
compartment. Record the serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
When you insert batteries for the
first time, or when you insert
batteries after the unit has been
without batteries for a certain
period of time, “Set Date&Time”
appears. Please refer “Step 2:
Setting the Clock” to set the date
and time.
If you keep V or v pressed, the unit
starts to search at higher speed.
During cue/review, the counter will
be displayed, regardless of the
display mode setting.
When you insert the batteries
for the first time after
purchasing (initializing the
Select the message and start
2
Model No. ICD-MX20
Serial No.
playback.
memory)
“ACCESS” appears in the display
window and the internal memory is
initialized automatically to create 5
folders (FOLDER01 to FOLDER05).
i (headphones) jack
1 When playback or fast playback
is done to the end of the last
message
1 Press v or V to display the desired message
number.
v: for previous message number
V: for next message number
2 Press Nx.
If the slot/connector lid is
accidentally detached,
attach it as illustrated.
• When fast playback is done to the
end of the last message, “Message
End” flashes for 5 seconds. (You
cannot hear the playback sound.)
• If you keep v pressed while
“Message End” is flashing, the
messages are played back rapidly,
and normal playback will start at
the point you release the key.
• When “Message End” stops
flashing and the OPR indicator goes
off, the unit will stop at the
beginning of the last message.
• If the last message is long and you
wish to start playback at a later part
of the message, keep V pressed to
play back the message to the end
and then press v while “Message
End” is flashing to go back to the
desired point.
If the battery compartment lid is
accidentally detached, attach it as
illustrated.
Notes while “ACCESS” appears
• The unit is accessing data while
“ACCESS“ appears in the display
window or the OPR indicator lights
or flashes in red or orange. While
accessing, do not remove the
batteries or AC adaptor (not
supplied). Doing so may damage
the data.
• If the unit is required to process
excessive amount of data,
“ACCESS“ may be displayed for an
extended period of time. This is not
a malfunction of the unit. Wait until
the message disappears.
Selected message number/Number of
messages in the selected folder
1 Built-in monaural/stereo microphone
(directional/all-directional)
qf HOLD switch
Playback slider
To prevent accidental operation, slide this switch to
“ON”. “HOLD” will appear for 3 seconds, indicating
that all the functions of the buttons are locked.
When the HOLD function is activated during stop,
all the display will be turned off after “HOLD” is
displayed.
To cancel the HOLD function
Slide the HOLD switch to “OFF”.
1 Tip
ICD-MX20
Displays the current
playback position.
Replacing the batteries
The battery indicator on the display window shows the battery condition:
You can set the directivity with the DIRECTNL
switch 2, and sensitivity with the “Mic Sense” in
the menu.
2005 Sony Corporation
Printed in China
:
Replace both of the two batteries with new ones.
Counter display*
:
“Replace Batteries” appears and the unit will stop operation.
Recorded date and time
of the message
2
DIRECTNL (directional) ON (MONO)/OFF switch
Slide the switch to set the directivity of the built-in
microphone 1 as follows:
Battery life* (Using Sony alkaline batteries LR03 (SG))
Recording mode: ST STLP SP
9 hr. 30 min. 9 hr. 30 min. 10 hr. 30 min.
9 hr. 9 hr. 9 hr.
(hr.: hours/min.: minutes)
LP
ON (MONO): To record a sound centering on a
specific direction in monaural. Use this position
when you record a sound at a conference/
meeting or in a spacious place etc.
OPR indicator**
(lights in green
during playback.)
3 Adjust the volume with VOLUME +/– .
* The display selected with the
In recording:
In playback:
8 hr.
8 hr.
Even if the HOLD function is activated, you can stop the
alarm playback. To stop the alarm or playback, press
xSTOP. (You cannot stop usual playback.)
For the customers in the USA
Troubleshooting
“Display” in the menu
appears.
Before taking the unit for repair, check the following
sections. Should any problem persist after you have made
these checks, consult your nearest Sony dealer.
INFORMATION
OFF: To record a sound not centering on a specific
direction (all-directional recording).
Notes
• The DIRECTNL switch is set to “ON”, sound is
recorded in monaural even if you select ST or STLP
mode.
• In the ST and STLP mode, sound is recorded in higher
quality sound thanks to their higher bit rates even in
the monaural recording.
* In continuous recording/playback
* In approximate hours and minutes
* When playing back through the internal speaker with the medium volume level
* The battery life may shorten depending on the operation of the unit.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
qg i (headphones) jack
**When the “LED” in the menu
is set to “OFF”, the OPR
indicator turns off.
To monitor the recording from the built-in
microphone, connect headphones supplied or not
supplied here. You can adjust the volume with
VOLUME +/– qa, but the recording level is fixed.
Note
If you turn up the volume excessively or place the
headphones near the microphone while monitoring
recording, the microphone may pick up the sound from
the headphones, causing acoustic feedback (howling
sound).
• For messages other than the last
one, go to the beginning of the next
message and play backward to the
desired point.
The unit does not operate.
• The batteries have been inserted with incorrect
polarity.
• The batteries are weak.
• The buttons are locked with the HOLD switch. (If you
press any button, “HOLD” will appear for 3 seconds.)
Using on house current
Connect the AC power adaptor (not
supplied) to the DC IN 3V jack of the
unit and to the wall outlet. Do not use
The unit plays all the messages in a folder continuously and stops at the
beginning of the last message in the folder. (You change the “Play Mode” in the
menu so that the unit plays a message and then stop at the beginning of the next
message .)
To DC IN 3V jack
Listening in better sound
quality
You can enjoy better sound quality as
AC power adaptor
(not supplied)
any other AC power adaptor.
3 Display window
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
The “Memory Stick” is not recognized. The
number of folders automatically created in the
“Memory Stick” is less than 5.
• Since the “Memory Stick” contains image data or other
files, the memory required for creating initial folders is
insufficient. Use the Windows Explorer or other tool to
delete unnecessary files or use “Format” menu of the
unit to format the “Memory Stick”.
For the details, see “Using the display window”
below.
follows:
To
Do this
• To listen from headphones: Connect
the stereo headphones (supplied or
not supplied) to the i
(headphones) jack. The built-in
speaker will be automatically
disconnected.
•To listen from an external speaker:
Connect an active or passive
speaker (not supplied) to the i
(headphones) jack.
qh m (microphone) jack (PLUG IN POWER)
You can connect an external microphone here. When
an external microphone is connected, the built-in
microphone is automatically cut off.
Polarity of the plug
stop at the current position
Press Nx or xSTOP.
4 OPR (operation) indicator
To resume playback from that point,
press Nx again.
The indicator lights in red during recording or in
green during playback. It flashes in red during
recording pause. During accessing the data, it lights
or flashes in red or orange. You can turn off the
indicator with the “LED” in the menu.
go back to the beginning
of the current message
Press v once.*
qj DPC ON/OFF switch
You can play back a message at a higher or lower
speed as follows:
–
–
Step 2: Setting the Clock
You need to set the clock to use the alarm function or record the date and time.
When you insert batteries for the first time, or when you insert batteries after
the unit has been without batteries for a certain period of time, “Set
Date&Time” appears. Set the date and time as follows:
skip to the next message
Press V once.*
No sound comes from the speaker.
• The headphones are plugged in.
• The volume is turned down completely.
go back to previous
messages/skip to succeeding
messages
Press v or V repeatedly.
(During stop mode, keep the key
pressed to skip the messages
continuously.)
5 Control key
ON: “Fast Play” or “Slow
Play” will be displayed
and a message is played
back at the speed specified
with the “DPC” in the
menu (between twice the
normal speed (+100%) and
half the normal speed (–
–
–
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Note on setting the clock
Set the clock while the set is in the
stop mode.
b (MENU)/B ( : folder)v(.: review)/V(>: fast
forward)/Nx (play/stop•enter)
Sound comes from the speaker even when the
6 zXREC (record) /PAUSE button
To display the clock setting
window and current time
You can display the clock setting
window to set the date and time or
check the current time:
* These operations are for when “Easy Search” in the menu is set to “OFF”.
headphones are plugged in.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
Press here to start and pause recording.
• If you plug in the headphones not securely during
playback, the sound may come from the speaker.
Unplug the headphones and then insert them securely.
Press the control key upward, downward, leftward, or
rightward (v/V/b/B) to select an item, and then press
down the center (Nx) to decide on the item.
7 xSTOP button
Press here to stop operation.
50%)).
For “Memory Stick”
Operating the Menu
During stop, playback or recording, you can use the menu to change the
operation modes in playback and recording, display mode, or other settings.
Display the menu and change the settings as follows:
In this manual, these operations are described as follows:
The OPR indicator does not light.
• The “LED” in the menu is set to “OFF”. Display the
menu and set the “LED” to “ON”.
8 Speaker
OFF: A message is played back at the normal speed.
1Press b (MENU) to display the
menu.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Sound is heard when no headphones or active
speaker are connected.
Press v (.).
qk VOICE UP (Digital Voice Up) ON/OFF switch
You can make the playback sound well-balanced and
more audible by enabling the Digital Voice Up
function as follows:
How the display changes in
the menu mode
You cannot start recording.
9 MEMORY STICK slot
Press B ( ;).
Insert the “Memory Stick Duo” or “Memory Stick
PRO Duo” here.
• The memory is full. Erase some of the messages. Or
use the Digital Voice Editor to save the IC recorder
messages to the hard disk of your PC. You can also use
the “Memory Stick” with sufficient capacity.
• The write-protect switch on the inserted “Memory
Stick” is set to “LOCK” .
Press b (MENU).
ON: Digital Voice Up function is activated. Inaudible
low-level part of a recorded message is amplified
so that the overall recording is adjusted to its
optimum level.
Entering the
menu mode (1)
If you have any questions about this product, you may
call: Sony Customer Information Services Center 1-800-
To
Do this
2Press v/V to select
and then press Nx.
(Preferences)
Press Nx.
0 USB connector
Press V (>).
Use the USB cable to connect a PC here.
1
2
3
enter the menu mode.
Press b (MENU).
3Press v/V to select “Date&Time”.
The current time is displayed in the
right bottom of the display
window.
select the desired menu (
/
/
/
). Press v/V and press Nx.
Press v/V and press Nx.
OFF: A message is played back without Digital Voice
Up function.
Note
Depending on the area you purchased the unit, the
Digital Voice Up switch name shown on the unit may
differ.
qa VOLUME (volume) +/– button
v
• 999 messages have already been recorded in the
selected folder. Select another folder or erase some of
the messages.
select the desired menu item.
go back to the previous step.
Adjust the playback sound with the button.
Declaration of Conformity
1
Press v/V to select the digits for the year.
v: to decrease the number
V: to increase the number
Selecting the
item in the
desired menu
(2, 3)
Trade Name:
Model:
SONY
Press v/V to select “ ” and press
Nx. ( If “ ” does not appear,
press b. )
qs DIVIDE button
ICD-MX20
Press to divide a message during playback.
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
You cannot erase a message.
2
3
Press Nx.
The month digits will flash.
qd A-B
(repeat) button
4
5
select the setting item.
exit the menu mode.
Press v/V and press Nx.
• The message or the folder containing the message is
set to “Read-only“ in the computer. Display the
message or the folder using Windows Explorer and
remove the check for “Read-only“ under “Properties“.
• The write-protect switch on the inserted “Memory
Stick” is set to “LOCK” .
ql Slit for a handstrap
Press to specify the beginning and ending points of
the portion to be played back repeatedly.
Press xSTOP.
v
Telephone Number: 858-942-2230
You can attach a handstrap (not supplied) here.
Repeat steps 1 and 2 to set the month, day,
4To set the clock, press Nx to
display the “Date&Time” window
and follow the steps 1 through 4 of
the “Step 2: Setting the Clock”.
If you do not press the key or button for one minute, the menu mode is automatically
cancelled and the window will return to normal display.
Selecting the
setting item
(4)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
hour, and then minutes in sequence.
To select a previous or next item
Press b for the previous item or B for the next
item.
w; Battery compartment /DC IN 3V jack
Open the compartment lid and insert two LR03 (size
AAA) alkaline batteries.
You cannot add a recording or an overwrite
recording to the previously recorded message.
Tip
Note
This unit does not have a power on/
off switch. The display is shown at all
times.
Using the display window
One message view
If you do not press Nx for more than one minute,
the clock setting mode is cancelled and the window
will return to normal display.
Menu items Settings (*: Initial setting)
Stop/Play/Rec**
• The remaining memory is too short. The overwritten
part will be deleted after the overwriting part finishes
recording. Therefore, you can only overwrite within
the remaining recording time.
• At a factory setting, “Add/Over” (additional/
overwrite recording) is set to “OFF”. Display the menu
and set the “Add/Over” to “Add REC” or
“Overwrite” .
List view (in stop mode)
Record/play menu
4
Press xSTOP to return to the normal
display.
REC Mode
You can set the recording mode (bit rate):
Notice for users
ST*:
STLP:
SP:
You can record with high-quality stereo sound. (48 kbps)
You can record with stereo sound for longer time. (24 kbps)
Program © 1999, 2000, 2001, 2002, 2003, 2004, 2005 Sony
Corporation
Documentation ©2005 Sony Corporation
OK/–/–
BBasic Operations
You can record with better sound (monaural sound). (16 kbps)
You can record for longer time (monaural sound). (8 kbps)
LP:
Note: When the DIRECTNL switch is set to “ON”, a message will be recorded in
monaural even in the “ST” or “STLP” recording mode.
All rights reserved. This manual or the software
described herein, in whole or in part, may not be
reproduced, translated or reduced to any machine
readable form without prior written approval from Sony
Corporation.
Recording is interrupted.
• The advanced VOR (Voice Operated Recording)
function is activated. Set “VOR” in the menu to “OFF”.
Recording Messages
Mic Sense
VOR
You can set the microphone sensitivity.
OK/–/OK
OK/–/OK
OK/–/–
You can record the maximum of 999 messages in each folder of the initially 5 folders
High*:
Low:
To record at meetings or in a quiet and/or spacious place.
To record dictation or in a noisy place.
Recording Messages
Maximum recording time*
(built-in memory)
The maximum recording time of all
the folders is as follows. You can
record messages for the maximum
recording time in a single folder.
(FOLDER01 to FOLDER05). In all the folders of the built-in memory, you can record
the maximum of 1,012 messages.
Since a newly recorded message is automatically added behind the last recorded
message, you can start recording quickly without searching for the end of the last
recording.
Recording is interrupted (when recording from
an external device).
• If you use an audio connecting cable without a resistor
to connect the sound source to the IC recorder, sound
may be recorded interrupted. Make sure to use a
resistance audio connecting cable.
You can activate or disable the VOR (Voice Operated Recording) function for
eliminating recording from soundless period.:
IN NO EVENT SHALL SONY CORPORATION BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR
IN CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION CONTAINED
HEREIN OR THE USE THEREOF.
ON:
Recording starts when the unit detects sound and “VOR” is displayed.
Recording pauses when no sound is heard and “VOR Pause” is displayed.
1 Folder icon
qs Microphone sensitivity indication
Displays the current microphone sensitivity
specified with the “Mic Sense” in the menu:
• H (High): To record at a meeting or in a quiet/
spacious place.
Recording modes**
Displays the icon of the current folder. You can
change the icon with the “Edit Folder” in the menu.
e.g.
Message 1 Message 2
Blank space
OFF*:
The VOR function is disabled. Normal recording operation is selected.
ST
Approx. 1 hr. 25 min.
Approx. 2 hr. 45 min.
Approx. 4 hr. 20 min.
Approx. 11 hr. 45 min.
Note: VOR function is affected by the sound around you. Set the “Mic Sense” according
to the recording conditions. If recording is not satisfactory after you have changed the
microphone sensitivity, or for important recording, set the “VOR” to “OFF”.
Noise is heard.
STLP
SP
Newly recorded message
• An object, such as your finger, etc., accidentally
rubbed or scratched the unit during recording so that
noise was recorded.
• The unit was placed near an AC power source, a
fluorescent lamp or a mobile phone during recording
or playback.
• Plug of the connected microphone was dirty when
recording. Clean the plug.
• Headphones plug is dirty. Clean the plug.
2 Priority marks
Displays the priority marks specified with the
“Priority” with the menu. You can renumber the
messages in the order of their priority.
Sony Corporation reserves the right to make any
modification to this manual or the information contained
herein at any time without notice.
LP
Add/Over
You can enable or disable the adding or overwrite recording mode:
• L (Low): To record for dictation or in a noisy
place.
(hr.: hours/min.: minutes)
* In continuous recording
**Recording modes:
ST: Standard play stereo recording
mode/STLP: Long play stereo
recording mode /SP: Standard play
monaural recording mode/LP:
Long play monaural recording
mode
OFF*:
You cannot add a recording to avoid erasing a message by accidental
operation.
Select the recording mode.
1
qd Drive indication
Displays the current drive:
: Built-in memory drive
: “Memory Stick” drive
3 Selected message number /Total number of
The software described herein may also be governed by
the terms of a separate user license agreement.
• This software is for Windows and cannot be used for
Macintosh.
• The supplied connecting cable is for the IC recorders
ICD-MX20. You cannot connect other IC recorders.
Add REC: You can adds a recording to a previously recorded message during playback.
Overwrite: You can adds an overwrite recording to a previously recorded message
during playback.
For how to select the recording mode, see “Operating the Menu”.
the messages in the selected folder
4 Alarm indicator
DPC
You can set the playback speed:
Appears when the alarm is set for a message.
Select the folder.
OFF*:
ON:
Messages will be played back at normal speed.
You can adjust the speed of the playback between twice the normal speed
qf Remaining battery indicator
OK/OK/–
OK/OK/–
2
Recording level is low.
5 Playback slider
Displays the remaining battery volume. When the
AC power adaptor (not supplied) is connected, the
indicator does not appear.
1 Press B ( ).
• “Mic Sense” (microphone sensitivity) is set to “Low”.
Display the menu and set “Mic Sense” to “High”.
• If it is difficult to hear small sound of a recorded
message, slide the VOICE UP switch to “ON”.
Playback sound may become more audible.
Displays the current playback position.
(+100%) and half the normal speed (–50%)
The folders in the built-in memory are
displayed.
The maximum number of the
folders when each folder
contains one message
You can create the maximum of 340
folders each in the built-in memory
and the “Memory Stick”.
Information
Easy Search
You can activate or disable the easy search function:
6 Counter (Elapsed time)/Remaining time /
Message name indication
Icon and name* of
ON:
You can go back for approx. 3 seconds by pressing v (.), or advance for
IN NO EVENT SHALL SELLER BE LIABLE FOR
ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE,
OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY
PRODUCT.
the selected folder
qg Folder name indication
approx. 10 seconds by pressing V (>).
The display mode selected with the “Display” in the
menu appears:
Elapse: Displays the elapsed
Displays the name of the current folder. You can
change the icon with the “Edit Folder” in the menu.
OFF*:
You can go back or forward the messages by pressing v/V (./>).
Built-in memory
Playback speed is too fast or too slow.
Play Mode
You can set the playback mode when you press Nx:
Cont Play*: The unit plays back all messages in a folder continuously.
One MSG: The unit plays back one message and then stops at the beginning of the next
message
drive (
)
qh Messages list
playback/recording time
• The playback speed is adjusted in the “DPC” in the
menu. Slide the DPC switch to “OFF” or display the
“DPC” in the menu and adjust the playback speed.
Notes before recording
• To record in better sound quality,
select the ST or STLP mode.
Displays the list of the three messages in the current
folder when “List View” in the menu is set to “ON”.
The number and recorded date/time of each
message is displayed. You can scroll the messages
with v/V.
of one message (counter).
OK/OK/–
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries with
separate collection systems)
* You can display a long folder name by
scrolling the cursor.
Repeat:
The unit plays back a message repeatedly until you press Nx or xSTOP.
“Repeat MSG” and “ “ will be displayed.
•
Before making a long recording, be
sure to check the battery indicator.
“--Y--M--D” or “--:--” is displayed.
• You have not set the clock. Display the “Date&Time”
in the menu and set the clock.
• The maximum recording time and
the number of messages you can
make varies depending on the
conditions of use.
• To avoid replacing batteries during
long time recording, use the AC
power adaptor (not supplied).
• You cannot record through the
built-in microphone if you connect
an external microphone to the m
(microphone) connector.
2 Press v or V to select the folder in which you
wish to record messages.
Remain: Displays the
remaining time of the
message in the playback
mode, and the
remaining recordable time
in the stop and recording
modes.
Name: Displays the message
name (title) if it is specified
with the supplied Digital
Voice Editor. (Some
characters that are not
compatible with the unit
may not be displayed.)
qj Scroll bar
Erase menu
“--Y--M--D” or “--:--” is displayed as the
recorded date.
• The date and time of recording will not be displayed if
you recorded the message when the clock was not set.
Display the “Date&Time” in the menu and set the
clock.
Displays the current location of the displayed
messages among the whole messages in the current
folder.
This symbol on the product
or on its packaging indicates
that this product shall not be
treated as household waste.
Instead it shall be handed
over to the applicable
collection point for the
recycling of electrical and
electronic equipment. By
ensuring this product is
disposed of correctly, you
will help prevent potential
negative consequences for
the environment and human
health, which could
Erase a MSG
Erase AllMSG
Erase Folder
Format
You can erase the currently selected message.
(See the reverse side.)
OK/OK/–
OK/–/–
3Press Nx.
You can erase all the messages in the selected folder.
(See the reverse side.)
Note
The effect of the back light of the display window may be
reduced in a bright location.
You can erase the selected folder and the messages contained in the folder.
(See the reverse side.)
OK/–/–
OK/–/–
There are fewer menu items in the menu
mode.
• There are some menu items which are not displayed
while the set is in recording or playback mode.
Start recording.
You can format a ”Memory Stick”. (See the reverse side.)
3
Switching the one message view and the
list view
You can choose how the messages will be displayed on
the stop mode between list view and one message view as
follows:
Expanding the memory
You can expand the memory by
inserting a “Memory Stick Duo” or
“Memory Stick PRO Duo” into the
MEMORY STICK slot. (See the
reverse side.)
1 Press zXREC/PAUSE during the stop
mode.
Edit menu
Built-in microphone
You do not need to keep pressing
zXREC/PAUSE while recording.
Priority
You can add priority marks (v) to the currently selected message.
Usually the recorded messages are lined up in the order of recording.
(None*/v/vv/vvv) (See the reverse side.)
A character in a folder or message name is
displayed as “s“.
• The unit cannot support and display some characters
which are entered using the supplied “Digital Voice
Editor“ software.
OK/OK/–
7 Recorded date and time indication
Recorded year, month, day, hours, and minutes of
the current message are displayed.
Current message number/
Number of messages in
the selected folder
1
2
Press b (MENU).
The menu window is displayed.
Move MSG
Alarm
You can move the currently selected message to the desired folder.
(See the reverse side.)
OK/OK/–
OK/–/–
Switching the drives
You can use both the built-in memory
and the “Memory Stick” by switching
drives as follows:
1Press B ( ) to display the folders
in the current drive.
Folder icon
otherwise be caused by inappropriate waste handling of
this product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product, please
contact your local Civic Office, your household waste
disposal service or the shop where you purchased the
product.
Press v/V to select
press Nx.
The Preferences menu is
displayed.
(Preferences) and then
Remaining
memory
indication
8 Repeat play indicator
You can set the alarm to the currently selected message.
(See the reverse side.)
Appears when “Repeat” (one message repeat
playback mode) is selected with the “Play Mode”
in the menu.
Messages are not sorted in order of the
number of priority marks in a folder.
• Unless you sort messages using the supplied “Digital
Voice Editor“ software, messages are displayed in the
unit in the same way as specified in the computer. Sort
again in the order of the number of priority marks in
the computer using the supplied “Digital Voice
Editor“ software.
Add Folder
Edit Folder
You can add a new folder to the end of the current drive.
(See the reverse side.)
OK/–/–
OK/–/–
Counter display*
2Press b.
3
4
Press v/V to select “List
View”.
You can change the icon and name of the currently selected folder.
(See the reverse side.)
9 Remaining memory indicator
3Press v or V to select the “Memory
Stick” drive ( ) or the built-in
memory drive ( ).
Displays the remaining memory:
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area).
•
•
•
During recording, the indicator decreases one by
one.
When the remaining recording time reaches 5
minutes, the indicator flashes.
When the remaining time
reaches 1 minute, the
Recording mode
Remaining memory indication
Microphone sensitivity
Press Nx.
The “List View” setting
window is displayed.
Preferences menu
Display You can change the display mode on the display window.
The remaining time displayed in the display
window is shorter than that displayed in the
supplied “Digital Voice Editor“ software.
OPR indicator**
(lights in red during recording.)
2 Speak to the built-in microphone.
Elapse:
Remain:
Name:
Displays the elapsed playback/recording time of one message (counter).
Displays the remaining time indication.
Displays the message name (title) if it is specified with the supplied Digital
Voice Editor software.
Notice for the customers in the countries
applying EU Directives
5
Press v/V to select
“ON” (list view) or
“OFF” (one message
view) and then press
Nx.
OK/OK/OK
The manufacturer of this product is Sony Corporation, 1-
7-1 Konan, Minato-ku, Tokyo, Japan. The Authorized
Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfi nger Strasse 61, 70327
Stuttgart, Germany. For any service or guarantee matters
please refer to the addresses given in separate service or
guarantee documents.
remaining time
* The display selected with the “Display” in the menu appears.
**When the “LED” in the menu is set to “OFF”, the OPR indicator turns off.
• The unit requires a certain amount of memory for
system operation. That amount is subtracted from the
remaining time, which is the reason for the difference.
“Memory Stick” drive (
)
indication 6 will flash
regardless of the display
mode.
Date&Time
You can set the clock manually or automatically:
4 Press Nx.
Automatic: If the unit is connected to a PC while the supplied Digital Voice Editor is
operating, the clock is automatically set according to the PC internal clock.
Manual*: Displays the window to set the clock manually (05Y1M1D*).
(See “Step 2: Setting the Clock”.)
The folders of the selected drive are
displayed, where you can select one
by pressing v or V.
The setting will be
changed.
OK/–/–
To
Do this
The battery life is short.
Remaining memory time
stop recording
Press xSTOP.
• The battery life mentioned in “Step 1: Installing the
Batteries” is based on playback through internal
speaker with the medium volume level (using Sony
alkaline batteries LR03(SG)). The battery life may
shorten depending on the operation of the unit.
(If you keep pressing v or V , the
display switches to the folders of
another drive.)
•
When the memory is full, recording automatically
stops and “Memory Full” will be displayed with
an alarm sound. To continue recording, first erase
some of the messages.
6
Press xSTOP to return to the normal display.
The unit stops at the beginning of the current
recording. If you do not change the folder after you
stop recording, the next time you record you will
record in the same folder.
Beep
LED
You can turn on or off the beep.
OK/OK/OK
ON*:
A beep will sound to indicate that operation has been accepted.
Starting recording
OFF:
No beep sound will be heard except for the alarm.
Notes
automatically in response to
the sound — Advanced VOR
function
You can turn on or off the OPR (operation) indicator during operation.
pause recording*
Press zXREC/PAUSE.
• If data other than sound data is saved, the remaining
memory time is displayed excluding the data. You can
check the remaining memory by selecting “Remain” in
the “Display” menu.
• When you set the “Beep” in the menu to “OFF”, an
alarm sound (beep) does not sound.
“ACCESS” display does not disappear.
• If the unit is required to process excessive amount of
data, “ACCESS“ may be displayed for an extended
period of time. This is not a malfunction of the unit.
Wait until the message disappears.
ON*:
The OPR indicator lights or flashes during operations such as recording or
playback.
During recording pause, the OPR indicator flashes in
red and “REC Pause” flashes in the display window.
OK/–/OK
Set “VOR” in the menu to “ON”.
OFF:
The OPR indicator turns off even during operation. (Even if you set the LED
to “OFF”, the indicator lights when the unit is connected to the PC.)
release pause and
resume recording
Press zXREC/PAUSE.
Recording resumes from that point.
Notes on recording
• While the OPR indicator flashes or
lights in red or orange, do not
remove the batteries or the AC
adaptor (not supplied). Doing so
may damage the data.
• Noise may be recorded if an object,
such as your finger, etc.,
accidentally rubs or scratches the
unit during recording.
Backlight
List View
You can turn on or off the backlight on the display window during operation.
listen to the current
recording
Press xSTOP to stop recording, then press Nx.
OK/OK/OK
OK/OK/–
ON*:
OFF:
The backlight on the display window lights during operation.
The backlight on the display window turns off during operation.
The unit does not operate correctly.
• Take out the batteries and insert them again with
correct polarity.
0 Recording mode indication
review the current
recording instantly
Press Nx during recording.
Displays the current recording mode specified with
the “REC Mode” in the menu:
You can select the list view or one message view in the stop mode.
ON:
OFF*:
List of the messages is displayed in the stop mode.
A message is displayed in the stop mode.
•
•
•
•
ST: Standard play stereo recording mode
STLP: Long play stereo recording mode
SP: Standard play monaural recording mode
LP: Long play monaural recording mode
review during recording Keep pressing v (.) during recording or
recording pause.
You cannot connect the unit to the PC.
• Refer to the “Digital Voice Editor 2” operating
instructions.
**Displays whether you can change the setting in each operation mode (Stop: stop mode/Play: playback mode/Rec: recording mode):
“OK” shows the setting can be changed and “–” shows the setting cannot be changed.
Recording stops and you can search backwards
while listening to fast playback sound. After you
release the key, playback starts from that point.
You can add an overwrite recording from that point.
Please note that recorded messages may be erased during
service or repair work.
qa VOR (Voice Operated Recording) indicator
Appears when the “VOR” in the menu is set to
“ON” and the voice operated recording is activated.
* About one hour after you pause recording, recording pause is automatically
released and the unit goes into the stop mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
|