4-147-229-13(1)
The software of this system may be updated in the future. To find out details on any
available updates, please visit: http://esupport.sony.com
BD/DVD Home Theatre System
Operating Instructions
BDV-T10 / T11 / E300
(1)
© 2009 Sony Corporation
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
• As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible AC
outlet. Should you notice an abnormality in the unit,
disconnect the main plug from the AC outlet
immediately.
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
For the customers in the U.S.A.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To reduce the risk of fire, do not cover the ventilation
opening of the apparatus with newspapers, tablecloths,
curtains, etc. Do not place the naked flame sources
such as lighted candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and do
not place objects filled with liquids, such as vases, on
the apparatus.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
Do not expose batteries or apparatus with battery-
installed to excessive heat such as sunshine, fire or the
like.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
Indoor use only.
Owner’s Record
CAUTION
The model and serial numbers are located at the rear
exterior of the control unit. Record the serial number in
the space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Model No. BDV-T10/BDV-T11/BDV-E300
Serial No.______________
The use of optical instruments with this product will
increase eye hazard. As the laser beam used in this BD/
DVD Home Theatre System is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
The following FCC statement applies only to the
version of this model manufactured for sale in the
USA. Other versions may not comply with FCC
technical regulations.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna (aerial).
This label is located on the laser protective housing
inside the enclosure.
This appliance is
classified as a CLASS 1
LASER product. This
marking is locatedon the
rear exterior.
Precautions
On power sources
• The unit is not disconnected from the mains as long
as it is connected to the AC outlet, even if the unit
itself has been turned off.
US
2
Download from Www.Somanuals.com. All Manuals Search And Download.
– Increase the separation between the equipment and
receiver.
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
®
– Consult the dealer or an experienced radio/TV
technician for help.
ENERGY STAR is a U.S.
registered mark.
®
As an ENERGY STAR partner,
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
Sony Corporation has determined
that this product meets the ENERGY
STAR guidelines for energy
®
efficiency.
Copyrights and Trademarks
Important Safety Instructions
• This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
Use of this copyright protection technology must be
authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
• This system incorporates with Dolby* Digital and
Dolby Pro Logic (II) adaptive matrix surround
decoder and the DTS** Digital Surround System.
* Manufactured under license from Dolby
Laboratories.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
“Dolby”, “Pro Logic”, and the double-D
symbol are trademarks of Dolby Laboratories.
**Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,392,195;
7,272,567; 7,333,929; 7,212,872 & other U.S.
and worldwide patents issued & pending.
DTS is a registered trademark and the DTS
logos, Symbol, DTS-HD and DTS-HD Master
Audio | Essential are trademarks of DTS, Inc.
© 1996-2008 DTS, Inc. All Rights Reserved.
• This system incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
• Java and all Java-based trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc.
• “BD-Live” and “BonusView” are trademarks of Blu-
ray Disc Association.
• “Blu-ray Disc” is a trademark.
• “Blu-ray Disc,” “DVD+RW,” “DVD-RW,”
“DVD+R,” “DVD-R,” “DVD VIDEO,” and “CD”
logos are trademarks.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
• “BRAVIA” is a trademark of Sony Corporation.
US
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• “AVCHD” and the “AVCHD” logo are trademarks of
Matsushita Electric Industrial Co., Ltd. and Sony
Corporation.
About These Operating
Instructions
• The instructions in these Operating
Instructions describe the controls on the
remote. You can also use the controls on the
unit if they have the same or similar names as
those on the remote.
• “S-AIR” and its logo are trademarks of Sony
Corporation.
•
, “XMB,” and “xross media bar” are trademarks of
Sony Corporation and Sony Computer Entertainment
Inc.
• “PLAYSTATION” is a trademark of Sony Computer
Entertainment Inc.
• “x.v.Color” and “x.v.Color” logo are trademarks of
Sony Corporation.
• Icons, such as
, listed at the top of each
explanation indicate what kind of disc can be
used with the function being explained.
• In this manual, “disc” is used as a general
reference for the BDs, DVDs, or CDs unless
otherwise specified by the text or illustrations.
• The instructions in this manual are for BDV-
T10, BDV-T11, and BDV-E300. BDV-T10 is
the model used for illustration purposes. Any
difference in operation is clearly indicated in
the text, for example, “BDV-T10.”
• “PhotoTV HD” and the “PhotoTV HD” logo are
trademarks of Sony Corporation.
• Other system and product names are generally
trademarks or registered trademarks of the
manufacturers. ™ and ® marks are not indicated in
this document.
• The Control Menu items may vary depending
on the area.
• The default setting is underlined.
US
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About the S-AIR function
The system is compatible with the S-AIR
function, which allows transmission of sound
between S-AIR products wirelessly.
The following S-AIR products can be used with
the system:
• Surround amplifier: You can enjoy surround
speaker sound wirelessly.
• Surround back amplifier: You can enjoy
surround back speaker sound wirelessly.
• S-AIR receiver: You can enjoy system sound
in another room.
The S-AIR products can be purchased as options
(the S-AIR product lineup differs depending on
the area).
Notes or instructions for the surround amplifier,
surround back amplifier, or S-AIR receiver in
these Operating Instructions refer only to when
the surround amplifier, surround back amplifier,
or S-AIR receiver is used.
For details on the S-AIR function, see “Using an
US
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Changing the Brightness of the Front
Panel Display.................................. 71
Step 3: Performing the Easy
Step 5: Enjoying Surround
Terms and Conditions of Use and End
User License Agreement.............. 103
Selecting the Effect to Suit
the Source .......................................47
Selecting the Audio Format, Multilingual
Tracks, or Channel..........................48
Enjoying Multiplex Broadcast
Sound..............................................49
Using the DIGITAL MEDIA PORT
Adapter ...........................................55
Using the Control for HDMI Function for
“BRAVIA” Sync ............................63
Calibrating the Appropriate Settings
Automatically .................................66
Controlling Your TV with the Supplied
Remote............................................69
US
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
BDV-T10
• Front speakers (2)
• FM wire antenna (aerial) (1) • Foot pads (1 set)
or
• Operating Instructions
• Speaker and TV Connections
• Speaker cords (5, white/red/
guide
• Surround speakers (2)
blue/gray/green)
• Setup Disc (DVD)
• DIGITAL MEDIA PORT
adapter (TDM-iP20) (1)
• Center speaker (1)
• Subwoofer (1)
• Video cord (1)
• Operating Instructions for
• Remote commander
the DIGITAL MEDIA
(remote) (1)
PORT adapter (TDM-iP20)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• AM loop antenna (aerial) (1)
US
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BDV-T11
• Front speakers (2)
• FM wire antenna (aerial) (1) • Foot pads (1 set)
or
• Operating Instructions
• Speaker and TV Connections
• Speaker cords (5, white/red/
guide
• Surround speakers (2)
blue/gray/green)
• Setup Disc (DVD)
• DIGITAL MEDIA PORT
adapter (TDM-iP20) (1)
• Center speaker (1)
• Subwoofer (1)
• Video cord (1)
• Operating Instructions for
the DIGITAL MEDIA
PORT adapter (TDM-iP20)
• Remote commander
(remote) (1)
• HDMI cable (1)
• R6 (size AA) batteries (2)
• AM loop antenna (aerial) (1)
• Calibration mic (1)
US
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BDV-E300
• Front speakers (2)
• FM wire antenna (aerial) (1) • Foot pads (1 set)
or
• Operating Instructions
• Speaker and TV Connections
• Speaker cords (6, white/red/
guide
• Surround speakers (2)
blue/gray/green/purple)
• Setup Disc (DVD)
• DIGITAL MEDIA PORT
adapter (TDM-iP20) (1)
• Video cord (1)
• Center speaker (1)
• Subwoofer (1)
• Operating Instructions for
the DIGITAL MEDIA
PORT adapter (TDM-iP20)
• Remote commander
(remote) (1)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• AM loop antenna (aerial) (1)
US
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Attaching the foot pads to the subwoofer
Attach the foot pads (supplied) to the bottom of the subwoofer to stabilize the subwoofer and prevent
it from slipping.
,
Remove the foot pads from
the protective cover.
US
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Switches to the optimum video mode for
watching movies automatically.
Index to Parts and
Control
For more information, refer to the pages
indicated in parentheses.
By only pressing the button, the TV turns
on, the TV is set for BD/DVD input
selector, and the system starts playing a disc
automatically.
Remote control
Turns on the TV or sets it to standby mode.
ONE-TOUCH
PLAY
TV
THEATER
1
2
BRAVIA Sync
S-AIR
MODE NIGHT BASS
Turns on the system or sets it to standby
mode.
DYNAMIC
TV
Selects playback mode for the S-AIR
receiver.
1
4
7
2
5
8
0
3
6
3
9
ENTER
TIME
NIGHT (page 50)
Activates the night mode function.
CLEAR
FAVORITES CC
WIDE
SYSTEM
AUDIO SUBTITLE ANGLE MENU
4
5
DYNAMIC BASS (page 49)
Reinforces bass frequencies.
D.TUNING
RED
GREEN
BLUE YELLOW
TV (page 69)
S
Changes to the TV operation mode for the
remote.
6
Enters the title/chapter numbers, radio
frequencies, etc.
FUNCTION
PRESET
SOUND MODE
7
8
REPLAY ADVANCE PRESET
TUNING
Clears the entry field.
TUNING
SCENE SEARCH
TIME (page 41)
0
VOLUME CH
TV INPUT
DISPLAY
Displays the elapsed/remaining playback
time in the front panel display.
MUTING
9
(page 69)
Inputs “.” (dot) when inputting numerics.
ENTER (page 69)
Enters the selected item.
Number 5, FAVORITES/AUDIO, CH +, and
N buttons have a tactile dot. Use the tactile dot
as a reference when operating the remote.
Selects the audio format/track.
SUBTITLE (page 38)
•
•
: For system operations
: For TV operations
(For details, see “Controlling Your TV with
Selects the subtitle language when multi-
lingual subtitles are recorded on a BD-
ROM/DVD VIDEO.
D.TUNING (page 53)
Selects the radio frequencies.
US
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ANGLE (page 38)
TOOLS (page 69)
Switches to other viewing angles when
multi-angles are recorded on a BD-ROM/
DVD VIDEO.
Displays the operation menu for the current
display.
Selects the playback source.
Enters the system menu.
FAVORITES (page 69)
Selects the sound mode.
Displays the favorite channel list.
H Playback operation buttons
CC (page 69)
Displays closed captioning (when
available).
./> (previous/next)
REPLAY/ADVANCE
m/M (fast reverse/fast forward)
N (play)
WIDE (page 69)
Changes the aspect ratio of the connected
TV.
X (pause)
E Color buttons (RED/GREEN/BLUE/
x (stop)
YELLOW) (page 84)
Short cut keys for selecting items on some
BD’s menus (can also be used for BD’s
Java interactive operations).
Radio operation buttons
PRESET +/–
Opens or closes the BD’s or DVD’s Top
Menu.
TUNING +/–
Displays the playback information on the
TV screen.
Turns off the sound temporarily.
POP UP/MENU (page 39)
Opens or closes the BD-ROM’s Pop-up
Menu, or the DVD’s menu.
Adjusts the volume.
CH +/– (page 69)
Selects the channels up and down.
Displays the options menu on the TV
screen.
TV INPUT (page 69)
Switches the TV’s input source between the
TV and other input sources.
DISPLAY (page 51)
Enters or exits the system’s home menu.
Changes the radio information in the front
panel display between radio frequency and
station name.
Returns to the previous display.
C/X/x/c
Switches to Scene Search mode that lets
you move quickly between scenes within
the title currently being played back.
Moves the highlight to a displayed item.
(ENTER)
Enters the selected item.
GUIDE (page 69)
Displays the Digital Electronic Programme
Guide (EPG).
US
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel
FUNCTION
VOLUME
C S-AIR indicator
Lights up when the S-AIR transceiver is
inserted in the unit and the system transmits
sound.
Turns on the unit, or sets to standby mode.
N (play)
Lights up while virtual 7.1ch decoding is
activated.
Starts or re-starts playback.
Plays a slideshow when a disc containing
JPEG image files is inserted.
E Power indicator
x (stop)
Lights up while the system is turned on.
Stops playback and remembers the stop
point (resume point).
F Front panel display
The resume point for a title/track is the last
point you played or the last photo for a
photo folder.
H
(remote sensor)
FUNCTION
Selects the playback source.
VOLUME +/–
Adjusts the system’s volume.
Z (open/close)
Opens or closes the disc tray.
US
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
About the indications in the front panel display
NEO:6 TUNED ST
EXT
HDMI
HD
24P NIGHT BASS
PL
x
SLEEP
A Current surround format
G Lights up when outputting 1920 ×
1080p/24 Hz video signals.
B Lights up when a station is received.
(Radio only) (page 51)
H Lights up when the night mode is on.
(page 50)
C Lights up when stereo sound is
received. (Radio only) (page 51)
I Lights up when the DYNAMIC BASS
D Lights up when the external memory is
recognized. (page 26)
J Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, decoding mode, etc.
E Lights up when the HDMI OUT jack is
correctly connected to an HDCP (High-
bandwidth Digital Content Protection)-
compliant device with HDMI or DVI
(Digital Visual Interface) input.
K Lights up when the system is
accessing the network.
F Lights up when outputting 720p/1080i/
1080p video signals from the HDMI
OUT jack or 720p/1080i video signals
from the COMPONENT VIDEO OUT
jacks.
L Displays system’s playing status.
M Flashes when the sleep timer is set.
(page 71)
US
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
Screws*
COMPONENT VIDEO OUT
VIDEO OUT
ANTENNA
COAXIAL 75
EZW-T100
Y
P
B
/
C
B
PR
/
C
R
FM
HDMI OUT
AM
TV
AUDIO
SAT/CABLE
DIGITAL IN
TV
EXT
500mA MAX
LAN(100)
DIGITAL IN
DC5V
L
L
SPEAKER
DMPORT
DC5V
700mA MAX
SPEAKER
A. CAL MIC
ECM-AC2
R
R
AUDIO IN
AUDIO IN
CENTER SUBWOOFER
FRONT
R
FRONT
L
SUR
R
SUR
L
COAXIAL
OPTICAL
B COMPONENT VIDEO OUT jacks (page
K TV (DIGITAL IN OPTICAL) jack (page
L SAT/CABLE (DIGITAL IN COAXIAL)
jack (page 23)
M DMPORT (DIGITAL MEDIA PORT) jack
*
CAUTION
Please do not remove the screws unless you
are installing the EZW-T100.
US
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Step 1: Installing the System
Positioning the speakers
For the best possible surround sound, place all speakers at the same distance from the listening position
(A). The distance can be between 0 to 23 feet (0.0 to 7.0 meters).
If you cannot place the center speaker and surround speakers at the same distance as (A), place them
within 23 feet (7.0 meters) of the listening position.
Place the surround speakers to the rear of the listening position (B).
The subwoofer can be placed anywhere in the room.
Center speaker
Subwoofer
Front left speaker (L)
Front right speaker (R)
A
A
A
30
30
B
45
45
B
A
A
Surround left speaker (L)
Surround right speaker (R)
Note
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,
oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not lean or hang on a speaker, as it may fall down.
US
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To add the optional surround back speakers
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP1,
optional). The optional product lineup differs depending on the area.
For the position of the surround back speakers, refer the illustration below (C).
Center speaker
Subwoofer
Front left speaker (L)
Front right speaker (R)
Surround left
speaker (L)
Surround right
speaker (R)
30 30
45
45
C
C
Surround back left speaker (L)
(optional)
Surround back right speaker (R)
(optional)
US
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the speakers on a wall
Caution
• Contact a screw shop or installer regarding the wall material or screws to be used.
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where
reinforcement is applied.
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or
improper screw installation, natural calamity, etc.
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Center speaker: Green
Surround left speaker (L): Blue
Surround right speaker (R): Gray
1
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
Hole on the back of
4 mm (5/32 inch)
the speaker
5 mm
(7/32 inch)
30 mm (1 3
/16 inches)
10 mm
13
(
/32 inch)
US
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Fasten the screws to the wall.
BDV-T10/BDV-T11
BDV-E300
For the center speaker
For the center speaker
160 mm
219 mm
3
5
(6
/
8 inches)
(8
/8 inches)
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch
)
(
/
to
/
inch)
32
32
32
32
For the other speakers
For the other speakers
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch
)
(
/
to
/
inch)
32
32
32
32
3
Hang the speakers on the screws.
Hole on the back of
the speaker
5 mm
(7/32 inch)
10 mm
13
(
/32 inch)
Rear of the speaker
US
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other
connections are made.
Note
• When you connect another component with a volume control, turn down the volume of the other components to a
level where sound is not distorted.
Connecting the speakers
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker.
Connect the speaker cords to match the color of the SPEAKER jacks of the unit.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #. Do not catch the speaker cord
insulation (rubber covering) in the speaker terminals.
To connect speaker cords to the unit
When connecting to the unit, insert the connector until it clicks.
Rear panel of the unit
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
Red
(Front right speaker (R)) (Front left speaker (L))
White
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
T
U
C
O
E
O
E
ID
V
L
T
U
O
O
E
ID
V
R
T
T
m
N
E
EX
0
5
X
A
N
O
Purple
P
M
A
M
O
0
C
DC5V
R
V
T
IN
IO
D
U
A
E
IN
L
L
A
B
A
IT
/
CR
A
/C
T
IG
D
IN
IO
R
P
(Subwoofer)
S
D
U
A
IN
L
A
B
C
IT
/
B
IG
P
D
Y
T
U
O
I
M
D
H
T
OR
P
M
D
L
A
IC
T
P
X
A
DC5V
O
M
A
m
0
0
7
L
IA
X
A
O
C
R
E
LAN(100)
A
K
E
P
S
L
R
U
S
R
R
U
S
L
T
N
O
R
F
R
T
N
O
R
F
Blue
R
E
K
A
E
P
S
(Surround left speaker (L))
R
O
W
B
U
S
N
E
C
Gray
(Surround right speaker (R))
Green
(Center speaker)
To connect speaker cords to the speaker
Rear of the speaker
Connector
(–)
(+)
Color tube
US
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Video connection)
This connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
Rear panel of the unit
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
T
U
C
O
E
O
E
ID
V
L
T
U
O
O
E
ID
V
R
T
N
XT
m
0
E
E
X
A
N
O
P
M
A
M
O
0
5
C
DC5V
R
V
T
IN
IO
D
U
A
E
L
L
A
B
A
IT
/
CR
A
/C
T
IG
D
IN
IO
R
P
S
D
U
A
IN
L
A
B
C
IT
/
B
P
IG
D
Y
T
OU
I
DM
H
T
R
PO
M
D
L
A
IC
T
P
X
DC5V
A
M
O
A
m
0
0
7
L
A Video cord (supplied)
IA
X
A
O
R
E
LAN(100)
A
K
E
P
S
L
R
U
S
R
R
U
S
L
T
N
O
R
F
R
T
N
O
R
F
R
E
K
A
E
P
S
R
E
F
O
O
W
B
U
S
R
E
T
N
E
C
C Component video
cable (not supplied)
B HDMI cable*
To the video input jack of
the TV.
To the component video
input jacks of the TV.
To the HDMI IN jack
of the TV.
* The HDMI cable is supplied with BDV-T11 only.
Method 1: Video cord (A) connection
This is the basic connection.
Method 2: HDMI* cable (B) and video cord (A) connection
If your TV has an HDMI jack, connect to the TV both with an HDMI cable and video cord. Picture
quality will be improved compared to using only the video cord connection.
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the
video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the HDMI OUT
jack.
* HDMI (High-Definition Multimedia Interface)
Method 3: Component video cable (C) and video cord (A) connection
If your TV does not have an HDMI jack, but has component video input jacks, connect to the TV both
with a component video cable and video cord. Picture quality will be improved compared to using only
the video cord connection.
When connecting with the component video cable, you need to select the type of output signal (pages
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the
video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the
COMPONENT VIDEO OUT jack.
US
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Audio connection)
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system,
perform this connection.
Rear panel of the unit
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
T
U
C
O
E
O
E
ID
V
L
T
U
O
O
E
ID
V
R
T
T
m
N
X
0
E
E
X
A
N
O
P
M
A
M
O
0
5
C
DC5V
R
V
T
N
I
IO
D
D Audio cord
(not supplied)
U
E
IN
L
L
A
B
A
T/C
IT
/
CR
A
IG
D
IN
IO
R
P
S
D
U
A
IN
L
A
B
C
IT
/
B
P
IG
D
Y
UT
I
O
M
D
H
T
R
O
P
M
D
L
A
IC
T
P
X
DC5V
A
M
O
A
m
0
0
7
L
IA
X
A
O
C
R
E
LAN(100)
A
K
E
P
S
L
R
U
S
R
R
U
S
L
T
N
O
R
F
R
T
N
O
R
F
E Digital optical cord
R
E
K
A
E
P
S
(not supplied)
R
E
F
O
O
W
B
U
S
R
E
T
N
E
C
To the digital optical out jack
of the TV.
To the audio out jacks of the TV.
Method 1: Audio cord (D) connection
This is the basic connection and sends an analog audio signal.
Method 2: Digital optical cord (E) connection
When the TV has a digital optical output jack, you can improve sound quality by connecting with a
digital optical cord in addition to an audio cord connection.
With a digital audio connection, the system receives a Dolby Digital multiplex broadcast signal and
you can enjoy multiplex broadcast sound.
Note
• The system can accept both digital and analog signals. Digital signals have priority over analog signals. If the digital
signal ceases, the analog signal will be processed after 2 seconds.
US
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the other components
You can enjoy connected components via the system’s speakers.
• DIGITAL MEDIA PORT adapter: F (TDM-iP20 is supplied. You can also use other DIGITAL
MEDIA PORT adapters.)
• VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): G
• VCR or digital satellite receiver, etc. (not supplied) which has a digital coaxial output jack: H
Rear panel of the unit
EZW-T100 slot (See “Wireless system options”.)
A
N
5
N
7
E
T
N
X
A
A
L
IA
H Digital coaxial cord
O
C
(not supplied)
M
F
0
0
1
-T
W
Z
E
M
C
A
F DIGITAL MEDIA PORT
adapter (page 55)
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
T
U
C
O
E
O
E
ID
V
L
T
U
O
O
E
ID
V
R
T
T
m
N
X
0
E
E
X
A
N
O
P
M
A
M
O
0
5
C
DC5V
R
V
T
IN
IO
D
U
A
E
IN
L
L
A
B
A
IT
/C
T
IG
D
IN
IO
/
CR
A
R
P
S
D
U
A
IN
L
A
B
C
IT
/
B
IG
P
D
Y
T
U
O
I
M
D
H
T
R
PO
DM
DC5V
L
A
IC
T
P
X
A
O
M
A
m
0
0
7
L
IA
X
A
O
C
R
E
LAN(100)
A
K
E
P
S
G Audio cord (not
supplied)
L
R
U
S
R
R
U
S
L
T
N
O
R
F
R
T
N
O
R
F
R
E
K
A
E
P
S
R
E
F
O
O
W
B
U
S
R
E
T
N
E
C
To the audio out jacks of the
VCR, digital satellite receiver,
PlayStation, or portable audio
source, etc.
To the digital coaxial out jack of the
VCR or digital satellite receiver, etc.
Note
• Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned. When disconnecting, pull out while
pressing
.
Wireless system options
By using an S-AIR product (not supplied), you can enjoy wireless performance by transmission from
the system. For details, see “Using an S-AIR Product” (page 56) or refer to the operating instructions
of the S-AIR product.
US
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If your TV has multiple audio/video inputs
You can enjoy sound with the speakers of the system through the connected TV. Connect the
components as follows.
TV
VCR, digital satellite receiver,
PlayStation, etc.
VCR, digital satellite receiver,
PlayStation, etc.
System
:Signal flow
Select the component on the TV. For details, refer to the operating instructions of the TV.
If the TV does not have multiple audio/video inputs, a switcher will be necessary to receive sound from
more than one component.
US
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the antenna (aerial)
To assemble the AM loop antenna (aerial)
To connect the antenna (aerial)
Rear panel of the unit
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
AM
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
C
E
L
R
T
X
5
E
X
A
M
A
m
0
0
DC5V
R
IN
IO
D
U
A
IO
D
U
A
AM loop antenna (aerial)
(supplied)
or
FM wire antenna (aerial)
(supplied)
Note
• Keep the AM loop antenna (aerial) and cord away from the system or other AV components, as noise may result.
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Outdoor FM antenna (aerial)
Unit
ANTENNA
COAXIAL 75
FM
AM
US
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the external memory
Insert the external memory device (1 GB or larger USB flash memory, such as Sony USM2GL,
USM4GL, or USM1GH, not supplied) into the EXT slot. Check that “EXT” lights up in the front panel
display when turning the system on. By connecting an external memory, you can enjoy additional
A
N
5
N
E
T
N
X
A
A
Rear panel of the unit
7
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
T
U
C
O
E
O
E
ID
V
L
T
U
O
O
E
ID
V
R
T
T
m
N
E
EX
0
5
X
A
N
O
P
M
A
M
O
0
C
DC5V
R
V
T
IN
IO
D
U
A
E
IN
L
L
A
B
A
IT
/C
T
IG
/
CR
A
D
IN
R
I
O
P
S
D
U
A
IN
L
A
B
C
IT
/
B
P
IG
D
Y
T
U
O
I
M
D
H
With the terminal
side up
T
R
O
P
M
D
L
A
IC
T
P
X
DC5V
A
O
M
A
m
0
0
7
L
IA
X
A
O
C
R
E
LAN(100)
A
K
E
P
S
L
R
U
S
R
R
U
S
L
T
N
O
R
F
R
T
N
O
R
F
R
E
K
A
E
P
S
R
E
F
O
O
W
B
U
S
R
E
T
N
E
C
Ex. Sony USM2GL (not supplied)
Note
• Insert the external memory into the EXT slot as far as it will go.
• Insert the external memory straight. If you force the external memory into the slot, this will cause damage to both
the external memory and the unit.
• Keep the external memory away from small children to prevent them from accidentally swallowing it.
• Do not apply too much pressure to the external memory in the slot, as it may cause a malfunction.
• To avoid data corruption or damage to the external memory, turn the system off when inserting or removing the
external memory.
• Do not insert an external memory that contains photo or music files to avoid corrupting the external memory data.
To remove the external memory
1
2
Press "/1 to turn the system off.
Pull out the external memory from the EXT slot.
US
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the network
Connect the LAN (100) terminal of the unit to your Internet source using a network cable to update the
Rear panel of the unit
COMPONENT VIDEO OUT
VIDEO OUT
ANTENNA
COAXIAL 75
EZW-T100
Y
P
B
/
CB
P
R
/
CR
FM
HDMI OUT
AM
TV
AUDIO
SAT/CABLE
DIGITAL IN
TV
EXT
500mA MAX
LAN(100)
DIGITAL IN
DC5V
L
L
SPEAKER
DMPORT
DC5V
700mA MAX
SPEAKER
A. CAL MIC
ECM-AC2
R
R
AUDIO IN
AUDIO IN
CENTER SUBWOOFER
FRONT
R
FRONT
L
SUR
R
UR
L
COAXIAL
OPTICAL
When connecting via a wireless
LAN router
When connecting to a
broadband router directly
Network cable
(not supplied)
Wireless LAN router
(access point)
(not supplied)
Network cable
(not supplied)
LAN(100)
Broadband router
(not supplied)
Ethernet/wireless
LAN media converter
(not supplied)
To PC
Network cable
(not supplied)
Network cable
(not supplied)
To PC
ADSL modem/
Cable modem
(not supplied)
ADSL modem/
Cable modem
(not supplied)
Internet
Internet
To update the system’s software using the network
Note
• Do not connect a phone line to the LAN (100) terminal, as it may cause a malfunction.
• Do not connect the LAN terminal of the unit to the LAN terminal of the PC.
• Depending on the modem or router, the type of network (LAN) cable, straight or crossing, differs. For details on
the network (LAN) cables, refer to the operating instructions supplied with the modem or router.
• For optimal performance of BD-Live functions, we recommend using an Internet connection with an effective
speed of 1 Mbps or greater.
US
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of the unit to a wall outlet (mains), connect all the
speakers to the unit.
Wall outlet (mains): The shape
of the wall outlet (mains) differs
depending on the area.
To turn off the demonstration mode
(Except for U.S. models)
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display.
You can turn off the demonstration simply by pressing "/1 on the remote. For details, see “About the
To turn the system on/off (standby mode)
"/1
1
4
7
2
5
8
3
6
9
Press "/1.
US
28
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press
or c.
The setting message appears.
Step 3: Performing the
Easy Setup
Follow the Steps below to make the basic
adjustments for using the system.
Displayed items vary depending on the country
model.
Easy Setup
Set the items below required to use this unit.
Each of these items may be changed later under "Setup."
- Select the TV connection method
- Select the TV type
- Select the BD Internet Connection
- Select the Standby Mode
- Execute the Auto Calibration
Check that all cables, etc. have been connected and then start.
Start
"/1
This message appears only when
performing the [Easy Setup] for the first
time. It does not appear when performing
the [Easy Setup] accessed via the [Setup]
setting.
1
4
7
2
5
8
0
3
6
9
6
7
Press
or c.
C/X/x/c,
The Setup Display for video cable selection
appears.
HOME
Easy Setup - TV Connection Method
Select the video cable connecting this unit and the TV.
Component Video
Video
1
2
3
Turn on the TV.
Press [/1 on the unit.
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
Press X/x to select the cable used to
connect the unit and TV.
Check the connection of the unit and TV
The Easy Setup Display for OSD language
selection appears.
• When you connect the unit and TV with
an HDMI cable, select [HDMI], go to
Step 8 and set the video output resolution
to match your TV.
Easy Setup - OSD
Select the language to be displayed by this unit.
English
Français
Español
• When you connect the unit and TV with a
component video cord, select
[Component Video], go to Step 8 and set
the video output resolution to match your
TV.
Português
If the Easy Setup Display does not
appear
• When you connect the unit and TV with
the video cord, select [Video] and go to
Step 9.
Recall the Easy Setup Display. See “To
4
Press X/x to select a language for the
OSD.
US
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Note
• When you do not connect the unit and TV with
an HDMI cable, you cannot select [HDMI].
• When connecting the HDMI OUT jack and
other video output jacks at the same time, select
[Component Video].
• If the picture is distorted or no picture appears,
wait for about 30 seconds without pressing any
buttons. [Is this resolution OK?] appears. Select
[Cancel]. The display returns to the resolution
setting screen.
• If the selected video output resolution is
incorrect, no picture appears on the screen. In
this case, press and hold N and Z on the unit
for more than 5 seconds to reset the video output
resolution to the lowest resolution. To change
the video output resolution, set [Output Video
• For details about video output resolution, see
8
Press
or c.
The Setup Display for video output
resolution selection appears. For details, see
9
Press
or c.
When you select [HDMI] in Step 7
The Setup Display for selecting the aspect
ratio of the TV to be connected appears.
Easy Setup - HDMI Resolution
Select the resolution to output to the TV. "Auto" is the standard selection.
The video switches for 30 seconds when this setting is changed.
Check that there are no problems with the video.
Easy Setup - TV Type
Nothing is displayed on the screen if the resolution is incorrect.
Auto
Select the screen aspect ratio to match your TV.
Select from [Auto], [480i], [480p], [720p],
[1080i], or [1080p].
When connecting the HDMI OUT jack and
other video output jacks at the same time,
video signals may only output from the
HDMI OUT jack when [Auto] or [1080p] is
selected.
10
11
Press X/x to select the setting that
matches your TV type.
• [16:9]: If you have a wide-screen TV or a
4:3 standard TV with a wide-screen mode.
When you select [Component Video] in
Step 7
• [4:3]: If you have a 4:3 standard TV.
Easy Setup - Component Resolution
Press
or c.
Select the resolution to output to the TV.
The video switches for 30 seconds when this setting is changed.
Check that there are no problems with the video.
When you connect the unit and TV with
an HDMI cable
Nothing is displayed on the screen if the resolution is incorrect.
The Setup Display for the [Control for
HDMI] function appears. Go to Step 12.
When you do not connect the unit and
TV with an HDMI cable
The Setup Display for [BD Internet
Connection] appears. Go to Step 14.
Select from [480i], [480p], [720p], or
[1080i].
When you change the video
output resolution
A picture is displayed in the selected
resolution for about 30 seconds, then the
display asks for confirmation.
Follow the on-screen instructions and go to
the next step.
US
30
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Press X/x to select the setting for the
Control for HDMI function.
16
Press X/x to select the standby mode.
You can operate the player quickly after
turning on this function.
Easy Setup - Control for HDMI
Select [Quick Start] if you want to shorten
the startup time from the standby mode. The
default setting is [Normal].
You can operate this unit in conjunction with a TV connected by HDMI.
Check your TV settings when using this function.
On
Note
• Quick Start mode will increase electricity
consumption in the standby mode.
17
18
Press
or c.
Select [On] to use the [Control for HDMI]
components that are compatible with the
Control for HDMI function.
The Setup Display for [Auto Calibration]
appears.
Connect the calibration mic to the
A.CAL MIC jack on the rear panel.
If you do not use the [Control for HDMI]
function, select [Off].
Set up the calibration mic at ear level using
a tripod, etc. (not supplied). The front of
each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic.
13
14
Press
or c.
The Setup Display for [BD Internet
Connection] appears.
Press X/x to select the setting for the
BD Internet connections.
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
C
E
L
R
T
EX
5
X
A
M
A
m
0
0
DC5V
R
V
T
N
I
IO
D
U
A
E
IN
L
L
A
B
A
IT
/C
IG
D
IN
IO
T
A
S
D
U
A
IN
L
A
IT
IG
D
L
A
IC
T
P
O
L
IA
X
A
O
C
Select [Allow] to allow Internet
connections.
If you do not allow the connections, select
[Do not allow].
Calibration mic
15
Press
or c.
The Setup Display for [Standby Mode]
appears.
19
Press X/x to select [Start].
To cancel, select [Cancel].
US
31
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Press
.
[Auto Calibration] starts.
Step 4: Selecting the
Source
The system adjusts the speaker setting
automatically.
Be quiet during the measurement.
You can select the playback source.
Note
• Loud test sound is output when [Auto
Calibration] starts. You cannot turn the volume
down. Give consideration to children and
neighbors.
• Before [Auto Calibration], install the surround
amplifier in the appropriate location. If you
install the surround amplifier in an improper
location, such as another room, proper
measurement will not be obtained.
1
4
7
2
5
8
0
3
6
9
• When you use the Wireless Surround Speaker
Kit (WAHT-SBP1, optional) for the surround
appropriate location and turn the surround
amplifier on.
FUNCTION
21
22
Confirm the conclusions of [Auto
Calibration].
The conclusions appear on the TV screen.
Press C/cto change the page. The first page
shows the distance of speakers. The second
page shows the level of speakers. If the
conclusions are OK, unplug the calibration
mic and press X/x to select [OK].
Press FUNCTION repeatedly until the
desired function appears in the front panel
display.
Each time you press FUNCTION, the function
changes as follows.
Note
• The environment of the room in which the
system is installed may affect measurements.
“BD/DVD” t “TUNER FM” t “TUNER
AM” t “TV” t “SAT/CABLE” t
“DMPORT” t “AUDIO” t …
Tip
• You can change a measurement unit (feet or
meters) by pressing the color button (RED).
Function
Source
Press
.
“BD/DVD”
Disc that is played by the system
Easy Setup is finished. All connections and
setup operations are complete.
“TUNER AM”
To quit the Easy Setup
“TV”
TV (component that is connected
Press HOME in any Step.
to the TV (AUDIO IN L/R) jacks
or TV (DIGITAL IN OPTICAL)
To recall the Easy Setup Display
“SAT/CABLE” Component that is connected to
the SAT/CABLE (DIGITAL IN
COAXIAL) jack on the rear panel
1
Press HOME.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Easy Setup], then
press
[Setup].
“DMPORT”
DIGITAL MEDIA PORT adapter
.
“AUDIO”
Component that is connected to
the AUDIO (AUDIO IN L/R)
jacks on the rear panel (page 23)
4
Press C/c to select [Start], then press
.
The Easy Setup display appears.
US
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Enjoying Surround Sound
You can enjoy surround sound simply by selecting one of the system’s pre-programmed decoding
modes. They bring the exciting and powerful sound of movie theaters into your home.
1
4
7
2
5
8
0
3
6
9
SYSTEM MENU
X/x/c,
Selecting surround sound effects based on your listening preference
1
Press SYSTEM MENU.
2
3
4
Press X/x repeatedly until “AUDIO MENU” appears in the front panel display, then press
or c.
Press X/x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c.
Press X/x repeatedly until the surround sound effect you want appears in the front panel
display.
See the table below for surround sound effect descriptions.
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
US
33
Download from Www.Somanuals.com. All Manuals Search And Download.
About speaker output
The table below describes the options when you connect all the speakers to the unit.
The default setting is “A.F.D. 7.1CH” (when connecting the headphones to the surround amplifier, the
default setting is “HP 2CH”).
Sound from
Surround effect
Effect
Depending on the source.
“A.F.D. STD”
(AUTO FORMAT
The system discriminates the sound format of the source and
presents sound as it was recorded/encoded.
DIRECT STANDARD)
“A.F.D. 7.1CH”
(AUTO FORMAT
DIRECT 7.1CH)
• 2 channel source: The system simulates surround sound
from 2 channel sources and outputs sound from the 5.1
channel speakers.
“PRO LOGIC”
“PLII MOVIE”
“PLII MUSIC”
– “A.F.D. 7.1CH” outputs sound from the 5.1 channel
speakers by duplicating 2 channel source sound across
each speaker.
– “PRO LOGIC” performs Dolby Pro Logic decoding.
– “PLII MOVIE” performs Dolby Pro Logic II movie
mode decoding.
– “PLII MUSIC” performs Dolby Pro Logic II music mode
decoding.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source. “A.F.D. 7.1CH” creates the surround back sound
virtually and gives you the sound as 7.1 channel surround
sound.
“A.F.D. 7.1CH”
These decoding modes appear only when you use the
Wireless Surround Speaker Kit (WAHT-SBP1, optional) for
(AUTO FORMAT
DIRECT 7.1CH)
“PLIIx MOVIE”
• 2 channel source: The system simulates surround sound
from 2 channel sources and outputs sound from all the
speakers including the surround back speakers.
– “A.F.D. 7.1CH” outputs sound from the 7.1 channel
speakers by duplicating 2 channel source sound across
each speaker.
”
“PLIIx MUSIC
– “PLIIx MOVIE” performs Dolby Pro Logic IIx movie
mode decoding.
– “PLIIx MUSIC” performs Dolby Pro Logic IIx music
mode decoding.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source.
“2CH STEREO”
The system outputs the sound from the front speakers and
subwoofer regardless of sound format or number of channels.
Multi-channel surround formats are downmixed to 2
channels.
US
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound from
Surround effect
Effect
2)
“HP 2CH”
This decoding mode appears only when you connect
headphones to the surround amplifier.
(HEADPHONE 2
CHANNEL
The system outputs the sound from the headphones
regardless of sound format or number of channels. Multi-
channel surround formats are downmixed to 2 channels.
STEREO)
To turn the sound effect off
Select “A.F.D. STD” for “DEC. MODE.”
Note
• When you select “A.F.D. 7.1CH,” depending on the disc or source, the beginning of the sound may be cut off while
the optimum mode is automatically selected. To avoid cutting the sound, select “A.F.D. STD.”
• When the input signal is multi-channel source, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are canceled
and the multi-channel source is output directly.
• When the bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• “A.F.D. 7.1CH,” “PRO LOGIC,” “PLII MOVIE,” “PLII MUSIC,” “PLIIx MOVIE,” and “PLIIx MUSIC” are
– “SPORTS”
– “OMNI-DIR”
– “MOVIE-D.C.S.-”
• Depending on the input stream, the decoding mode may not be effective.
• When changing the decoding mode while using the S-AIR receiver, sound from the S-AIR receiver may skip.
Tip
• The system memorizes the last decoding mode selected for each function.
Whenever you select a function such as “BD/DVD” or “TUNER FM,” the decoding mode that was last applied to
the function is automatically applied again. For example, if you select “BD/DVD” with “PRO LOGIC” as the
decoding mode, then change to another function, and then return to “BD/DVD,” “PRO LOGIC” will be applied
again.
US
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Press Z.
Place a disc.
Playback
Place one disc on the disc tray, and then
press Z.
Playing a BD/DVD
Depending on the disc, some operations may be
different or restricted.
Refer to the operating instructions supplied with
your disc.
FUNCTION
"/1
x
N
Z
When you insert a commercially available
BD-ROM or DVD VIDEO, playback may
automatically start depending on the disc.
In this case, go to Step 9.
FUNCTION
VOLUME
Note
• When you play an 8 cm disc, place it on the
inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
• Do not place more than one disc on the tray.
Disc tray
VOLUME +/–
ONE-TOUCH
PLAY
7
8
Press C/c to select
[Video].
"/1
Press X/x to select
, then press N
Number
buttons
TIME
1
4
7
2
5
8
0
3
6
9
or
.
SUBTITLE
SYSTEM
MENU
BD Data
DISPLAY
TOP MENU
ANGLE
Video
POP UP/
MENU
C/X/x/c,
HOME
FUNCTION
/
SCENE
SEARCH
MUTING
OPTIONS
./>
N
m/M
For commercially available BD-ROM or
DVD VIDEO, playback starts.
For a BD or DVD recorded on other
equipment, the title list appears. Press X/x
to select the desired title, then press N or
.
x
X
VOLUME
+/–
1
2
Turn on your TV.
Switch the input selector on the TV to
this system.
Playback starts.
9
Press VOLUME +/– to adjust the
volume.
3
4
Press "/1.
The system turns on.
The volume level appears on the TV screen
and in the front panel display.
Press FUNCTION repeatedly until “BD/
DVD” appears in the front panel
display.
US
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
To
Press
• When you set the [Control for HDMI] function to
[On], the TV that is connected to the system with an
HDMI cable can be sync-operated with the system.
For details, see “Using the Control for HDMI
Play in slow, freeze M for more than one second in
frame (playback
direction only)
pause mode. When you press
M briefly in pause mode, you
can play one frame at a time.
Depending on the disc, this
function may not work.
To return to normal playback,
press N.
Tip
• You can change the speed at which the volume is
turned up and down.
To turn the volume up/down quickly, press and hold
VOLUME +/–.
Replay the
previous scene
(instant replay) during
playback.
2)
To set the volume up/down precisely, press
VOLUME +/– briefly.
Briefly fast
(instant advance) during
forward the current playback.
3)
scene
Other operations
1)Scan speeds may differ with some discs.
2)BD/DVD VIDEO/DVD-RW/DVD-R only.
3)BD/DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
DVD+R only.
To
Press
x
Stop
Pause
X
Resume play after X or N
To play a restricted BD or DVD
(Parental Control)
pause
Go to the next
chapter
>
When you play a restricted BD
Change [BD Parental Control] in [BD/DVD
Go back to the
preceding chapter
. twice in a second.
When you press . once, you
can go to the beginning of the
current chapter.
When you play a restricted DVD
Change [DVD Parental Control] in [BD/DVD
Turn off the sound MUTING
temporarily
To cancel, press it again or
VOLUME + to adjust the sound
volume.
When you play a restricted BD or DVD, the
display for entering your password appears on
the screen.
Remove the disc
Locate a point
quickly by playing Each time you press M or m
a disc in fast
forward or fast
Z on the unit.
Mor mwhile playing a disc.
Enter your four-digit password using the
number buttons, and press
Playback starts.
.
during scan, the playback speed
changes as follows:
1)
To register or change the password, see
reverse (Scan)
Playback direction
M1 (×10) t M2 (×30) t
M3 (×120)
To play a restricted BD-RE or BD-
R (Disc Lock)
Reverse direction
n (×1) t m1 (×10) t
m2 (×30) t m3 (×120)
When you play a BD-RE or BD-R restricted by
the Disc Lock function, the display for entering
your password appears on the screen.
When you press and hold the
button, fast forward/fast reverse
continues at the selected speed
until you release the button.
To return to normal speed, press
N. Actual speeds may differ
with some discs.
1
Enter the four-digit password that has
been registered when creating the disc
using the number buttons, and press
.
2
Select a title, and press N or
.
Playback starts.
US
37
Download from Www.Somanuals.com. All Manuals Search And Download.
One-Touch Play (for HDMI
connection only)
Press ONE-TOUCH PLAY.
Changing the angles
The system and the connected TV turn on and
the input selector on the TV is switched to the
system; then you can enjoy the contents of a
disc.
If various angles (multi-angles) for a scene are
recorded on a disc, you can change the viewing
angle.
Note
Press ANGLE during playback to select the
desired angle.
• When using the HDMI connection, there may be a
delay before the playback picture appears on the
screen, and the beginning portion of the playback
picture may not be displayed.
• To use this function, set [Control for HDMI] to [On]
Displaying the subtitles
Available OPTIONS
1
Press OPTIONS.
If subtitles are recorded on a disc, you can turn
the subtitles on/off during playback. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language during
playback, or turn the subtitles on/off whenever
you want.
The options menu appears.
2
Press X/x to select an item, then press
.
The available items differ depending on the
disc type or system situation.
Press SUBTITLE during playback to select
the desired subtitle language.
Items
Details
[Video Settings]
Adjusts settings for picture
[Title List]
[Play]
Displays the title list.
Plays the title from the
point where you pressed x.
[Play from beginning] Plays the title from the
beginning.
[Top Menu]
Displays the disc’s Top
[Menu/Popup Menu]
Displays the BD-ROM’s
Pop-up Menu or DVD’s
[Stop]
Stops playback.
[Title Search]
Searches for a title and
starts playback from the
[Chapter Search]
Searches for a chapter and
starts playback from the
US
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Resuming playback from the
point where you stopped the
disc
Using the BD’s or DVD’s menu
To display the Top Menu
(Resume Play)
A BD/DVD is divided into a lot of sections,
which make up a picture or music feature. These
sections are called “titles.” When you play a BD/
DVD which contains several titles, you can
select the title you want using the Top Menu.
You can also select items such as the language
for the subtitles and the language for the sound
using the Top Menu.
When you stop the disc, the system remembers
the point where you pressed x. As long as you
do not remove the disc, Resume Play will work
even if the system is set to standby mode by
pressing "/1.
1
2
While playing a disc, press x to stop
playback.
1
Press TOP MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary depending
on the disc.
Press X/x to select
or
, then press N
.
The system starts playback from the point
where you stopped the disc in Step 1.
2
3
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
Note
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
point.
Press
.
To display Pop-up Menus
Some BD-ROMs contain Pop-up Menus that
• The point where you stopped playing may be cleared
when:
– you open the disc tray.
appear without interrupting playback.
– you play another title.
1
2
Press POP UP/MENU during playback.
– you change the settings on the system.
– you disconnect the AC power cord (mains lead).
– you remove the external memory (for BD-ROMs).
• This function may not work properly with some
discs.
The Pop-up Menu appears.
Press C/X/x/c, the color buttons, or
number buttons to select the item, and
follow the on-screen instructions.
To play from the beginning of the
title
Press OPTIONS to select [Play from beginning],
then press
. Playback starts from the
beginning of the title.
US
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a scene quickly
Searching for a Title/Chapter
(Scene Search)
You can search for a chapter if the title contains
chapter marks.
You can move quickly between scenes within
the title currently being played back.
1
Press OPTIONS during playback or in
pause mode.
1
Press SCENE SEARCH during
playback or in pause mode.
The options menu appears.
Playback pauses and a bar with a scene
indicator (square-shaped – indicates the
current point) appears at the bottom of the
screen.
2
Press X/x to select a search method,
then press
.
• [Title Search] (for a BD-ROM/DVD
VIDEO): Searches the desired title.
• [Chapter Search]: Searches the desired
chapter.
2
Press and hold C/c or m/M to move
the scene indicator to the scene you
are searching for.
The display for entering the number
appears.
Scene indicator
Example: Chapter Search
Chapter :
Scene Search
The current point
The scene indicator on the bar is displayed
around the playing point.
3
4
Press the number buttons to enter the
number of the title or chapter.
3
4
Release the button at the point you
want to watch.
If you make a mistake, press CLEAR, and
re-enter another number.
The scene at which you released the button
is displayed in pause mode.
Press
.
After a while, the system starts playback
from the selected number.
To search for a scene again, move the scene
indicator using C/c or m/M.
To cancel [Title Search]/[Chapter
Search]
Press SCENE SEARCH,
, N, or X.
Playback starts.
Press RETURN.
To cancel Scene Search mode
Press SCENE SEARCH, , N, or X.
Playback starts from the point you pressed the
button.
Note
• The Scene Search function is available for titles
longer than 100 seconds and shorter than 100 hours.
• Depending on the disc, this function may not work.
US
40
Download from Www.Somanuals.com. All Manuals Search And Download.
To view the playing time and
remaining time in the front panel
display
Displaying the playing time
and play information
Press TIME repeatedly.
Each time you press TIME while playing the
disc, the display changes:
1 y 2
You can check the title information, including
the video transmission rate, etc.
Press
DISPLAY during playback.
1 Playing time of the current title
2 Remaining time of the current title
The displayed information differs depending on
the disc type and system status.
Some displayed items may disappear after a few
seconds.
Example: When playing a BD-ROM
Angle
English Dolby Digital Plus
Mbps
A
B
C
D
The current selected angle
Title number or name
The currently selected audio setting
Available functions (
subtitle)
angle/
audio/
E
Playback information
Displays Disc type/Play mode/Video codec/
Bit rate/Playing status bar/Playing time
(Remaining time*)
F
Output resolution/Video frequency
* Displayed when you press TIME repeatedly.
Tip
• You can also check the playback information in the
front panel display.
• You can change each setting by pressing SUBTITLE,
AUDIO, or ANGLE.
US
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Adjusting pictures for videos
• Set the picture setting of your TV to [Standard] before
changing [Picture Quality Mode].
• [Video Settings] is disabled when the connected TV
• Depending on the disc or the scene being played,
[FNR], [BNR], or [MNR] effects may be hard to
discern.
1
Press OPTIONS during playback.
The options menu appears.
2
Press X/x to select [Video Settings],
then press
.
The [Video Settings] screen appears.
Adjusting the delay between
the picture and sound
(A/V SYNC)
Video Settings
Select the item you want to change.
Close
Picture Quality Mode Standard
FNR
BNR
MNR
Standard
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
1
2
Press SYSTEM MENU.
3
Press X/x to select an item, then press
Press X/x repeatedly until “AUDIO
MENU” appears in the front panel
display, then press
.
[Picture Quality Mode]
Optimizes the picture settings for different
lighting environments.
• [Standard]
or c.
3
4
Press X/x repeatedly until “A/V SYNC”
appears in the front panel display, then
press
or c.
• [Brighter Room]
Press X/x to adjust the delay between
the picture and sound.
• [Theater Room]
[FNR]
You can adjust from 0 ms to 300 ms in 25
ms increments.
Reduces random noise appearing in the
picture.
• [Off]
5
Press
.
The setting is made.
• [Auto]
6
Press SYSTEM MENU.
[BNR]
Reduces mosaic-like block noise in the
The system menu turns off.
picture.
Note
• [Off]
• Depending on the input stream, A/V SYNC may not
be effective.
• [Auto]
[MNR]
Reduces minor noise around the picture
outlines (mosquito noise).
• [Off]
• [Auto]
4
Press C/X/x/c to select or adjust the
settings, then press
.
To adjust any other items, repeat steps 3 and
4.
US
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Select the disc name, then press
OPTIONS.
Enjoying BonusView/BD-
Live
6
7
Select [Erase], then press
Select [OK], then press
.
.
The data of the selected disc will be deleted.
Note
• Depending on the BD-ROM, the disc name may not
be displayed.
Some BD-ROMs with “BD-LIVE Logo*” have
bonus contents and other data that can be
downloaded to the external memory (local
storage) for enjoyment.
Tip
• To delete all data in the external memory at once,
select [Erase All] in Step 6.
• Press
6.
instead of OPTIONS in Step 5 to skip Step
*
1
If a disc is inserted, remove the disc
from the unit.
2
3
Turn the system off.
Insert the external memory (not
supplied) into the EXT slot on the rear
of the unit.
The external memory is used as the local
storage.
Make sure that the external memory is
4
Connect the system to a network
5
6
Turn the system on.
Set [BD Internet Connection] to [Allow]
in [BD/DVD Viewing Settings]
7
Insert a BD-ROM with BONUSVIEW/
BD-LIVE.
The operation method differs depending on
the disc. Refer to the instruction manual
supplied with the disc.
To delete data in the external
memory
You can delete unnecessary data.
1
If a disc is inserted, remove the disc
from the unit.
2
3
4
Press HOME.
Press C/c to select
Press X/x to select [BD Data], then
press
[Video].
.
US
43
Download from Www.Somanuals.com. All Manuals Search And Download.
To select a track
Playing a CD
1
2
Press HOME.
Press C/c to select
[Music].
Music
Music CD
1
4
7
2
5
8
0
3
6
9
TIME
3
4
Press
The music list appears.
Press X/x to select a track, then press
N or
The system plays the selected track.
.
C/X/x/c,
HOME
OPTIONS
FUNCTION
.
./>
N
m/M
x
X
Other operations
MUTING
VOLUME
+/–
To
Press
Stop
Pause
x
X
1
Press FUNCTION repeatedly until “BD/
DVD” appears in the front panel
display.
Resume play after pause X or N
Start playback from the
point where you pressed
x.
N
2
3
Insert a CD.
The Music Player screen appears.
Go to the next track
>
Press N.
Go back to the
preceding track
. twice in a second.
When you press . once,
you can go to the beginning
of the current track.
Playback starts.
Music CD
Stereo
Turn off the sound
temporarily
MUTING
To cancel, press it again or
VOLUME + to adjust the
sound volume.
Remove the disc
Z on the unit.
Fast reverse/fast
forward
m or M during
playback.
Current track number and elapsed time
4
Adjust the volume by pressing
VOLUME +/–.
The volume level appears on the TV screen
and in the front panel display.
US
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Available OPTIONS
Playing Photo Files
1
Press OPTIONS.
The options menu appears.
1)
2)
3)
2
Press X/x to select an item, then press
.
1)BD-REs/BD-Rs containing JPEG image files
2)DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs
containing JPEG image files
The available items differ depending on the
disc type or system situation.
Items
Details
3)CD-RWs/CD-Rs containing JPEG image files
[Play]
Plays the selected track.
[Play from beginning] Plays the current track from
(during playback) the beginning.
[Play from beginning] Plays the selected track
1
4
7
2
5
8
0
3
6
9
(in stop mode)
from the beginning.
[Stop]
Stops playback.
DISPLAY
Note
• The point where you stopped playing (resume point)
is cleared from memory when:
C/X/x/c,
HOME
OPTIONS
– You open the disc tray.
FUNCTION
./>
– You turn the system off.
N
To view the playing time and
remaining time in the front panel
display
x
X
1
Press FUNCTION repeatedly until “BD/
DVD” appears in the front panel
display.
Press TIME repeatedly.
Each time you press TIME while playing the
disc, the display changes:
1 t 2 t 3 t 4 t 1 t ...
2
3
4
Insert a disc that contains photo files.
Press HOME.
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
Press C/c to select
[Photo].
4 Remaining time of the disc
Photo
Data CD
5
6
Press
.
The file list or folder list appears.
Press X/x to select a file or folder, then
press
.
When you select a folder, press X/x to
select a file in the folder, then press
The selected photo file is displayed.
.
US
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Other operations
Note
• When you attempt to play the following photo files,
To
Press
the
mark appears on the screen and they cannot
be played.
Play a slideshow
Stop a slideshow
Pause a slideshow
Go to the next photo
N
x
– Photo files with width or height larger than 8,192
pixels
X
– Photo files with width or height smaller than 15
pixels
>
.
Go back to the
– Photo files exceeding 32 MB
preceding photo
– Photo files with extreme aspect ratios (greater than
50:1 or 1:50)
Display the file
information
DISPLAY
– Photo files in Progressive JPEG format
– Photo files that have a “.jpeg” or “.jpg” extension,
but are not in JPEG format
Available OPTIONS
– Photo files that have an extremely long name
• The following photo files cannot be played.
– Photo files recorded on BD-Rs in any format other
than UDF (Universal Disk Format) 2.6
– Photo files recorded on BD-REs in any format
other than UDF (Universal Disk Format) 2.5
• The following photo files or folders cannot be
displayed in the file list or folder list.
– Photo files that have an extension other than
“.jpeg” or “.jpg”
1
Press OPTIONS.
The options menu appears.
2
Press X/x to select an item, then press
.
The available items differ depending on the
situation.
Items
Details
1)2)
[Slideshow Speed]
Changes the slideshow
speed.
– Photo files that have an extremely long name
– Photo files in the 5th tree and photo files/folders in
the 6th tree or lower
• [Fast]
• [Normal]
• [Slow]
– Folders beyond the 500th folder, when the total
number of folders and files in a single tree exceeds
500
1)
[Stop]
Stops a slideshow.
• Photo files edited on a PC may not be played.
• Thumbnail images of some photo files may not be
displayed.
1)
[Rotate Left]
Rotates the photo
counterclockwise by 90
degrees.
• Large photo files may take some time to display or to
start a slideshow.
1)
[Rotate Right]
Rotates the photo
clockwise by 90 degrees.
2)
[View Image]
Displays the selected
picture.
To view images in high picture
quality
If you have a Sony TV compatible with
“PhotoTV HD,” you can enjoy images in high
picture quality by the following connection and
setting.
2)
[Slideshow]
Starts a slideshow.
1)Appears when you press OPTIONS during playback
of photo files.
2)Appears when you press OPTIONS while the file/
folder list is displayed.
1
2
Connect the unit to the TV using an
HDMI cable.
Set the TV’s video setting to [VIDEO-A]
mode.
For details on [VIDEO-A], refer to the
operating instructions supplied with the
TV.
US
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• When you connect headphones to the surround
amplifier, the sound mode is disabled.
• Depending on the disc or source, when you select
“AUTO,” the beginning of the sound may be cut off
as the system selects the optimum mode
automatically. To avoid cutting the sound, select
other than “AUTO.”
Sound Adjustment
Selecting the Effect to
Suit the Source
You can select a suitable sound mode for movies
or music.
• Depending on the input stream, the sound mode may
not be effective.
• When changing the sound mode while using the
S-AIR receiver, sound from the S-AIR receiver may
skip.
1
4
7
2
5
8
0
3
6
9
SOUND
MODE
Press SOUND MODE repeatedly during
playback until the desired mode appears in
the front panel display.
• “AUTO”: The system selects “MOVIE” or
“MUSIC” automatically to produce the sound
effect depending on the disc or sound stream.
• “MOVIE”: The system provides the sound for
movies.
• “MOVIE-D.C.S.-”*: The system reproduces
the sound characteristics of the Sony Pictures
Entertainment “Cary Grant Theater” cinema
production studio.
• “MUSIC”: The system provides the sound for
music.
• “SPORTS”: The system adds reverberation for
the sports program.
• “NEWS”: The system provides the sound for
the voice program, such as news.
• “OMNI-DIR”: The same sound is audible
anywhere in the room.
* DCS technology is used.
US
47
Download from Www.Somanuals.com. All Manuals Search And Download.
x DVD-VR
The types of sound tracks recorded on a disc are
displayed.
Example:
Selecting the Audio
Format, Multilingual
Tracks, or Channel
When the system is playing a BD/DVD VIDEO
recorded in multiple audio formats (PCM,
Dolby Digital, MPEG audio, or DTS), you can
change the audio format. If the BD/DVD
VIDEO is recorded with multilingual tracks,
you can also change the language.
• [ Stereo]
• [ Stereo (Audio1)]
• [ Stereo (Audio2)]
• [ Main]
• [ Sub]
• [ Main/Sub]
Note
• [ Stereo (Audio1)] and [ Stereo (Audio2)] do not
appear when only one audio stream is recorded on the
disc.
With a CD, you can select the sound from the
right or left channel and listen to the sound of the
selected channel through both the right and left
speakers.
x CD
• [ Stereo]: The standard stereo sound.
• [ 1/L]: The sound of the left channel
(monaural).
• [ 2/R]: The sound of the right channel
(monaural).
1
4
7
2
5
8
0
3
6
9
AUDIO
Press AUDIO repeatedly during playback to
select the desired audio signal.
The audio information appears on the TV
screen.
x BD/DVD VIDEO
Depending on the BD/DVD VIDEO, the choice
of language varies.
When 4 digits are displayed, they indicate a
language code. See “Language Code List”
(page 102) to confirm which language the code
represents. When the same language is
displayed two or more times, the BD/DVD
VIDEO is recorded in multiple audio formats.
US
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Multiplex
Broadcast Sound
(DUAL MONO)
You can enjoy multiplex broadcast sound when
the system receives or plays a Dolby Digital
multiplex broadcast signal.
Using the Sound Effect
DYNAMIC
BASS
NIGHT
1
4
7
2
5
8
0
3
6
9
SYSTEM
MENU
Note
• To receive the Dolby Digital signal, you need to
connect a TV or other component to the unit with an
the digital output mode of the TV or other component
to Dolby Digital.
C/X/x/c,
1
4
7
2
5
8
0
3
6
9
Reinforcing bass frequencies
AUDIO
You can reinforce bass frequencies.
Press DYNAMIC BASS.
“D. BASS ON” appears in the front panel
display and bass frequencies are effectively
reinforced.
During this mode is on, “BASS” lights up in the
front panel display.
To turn off the sound effect
Press AUDIO repeatedly until the desired
signal appears in the front panel display.
Press DYNAMIC BASS so that “BASS”
disappears from the front panel display.
• “MAIN”: Sound of the main language will be
output.
• “SUB”: Sound of the sub language will be
output.
• “MAIN/SUB”: Mixed sound of both the main
and sub languages will be output.
US
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying sound at low volume
Changing the tonal balance
You can enjoy sound effects or dialog, as you
would in a movie theater, even at low volume. It
is useful for watching movies at night.
You can adjust the sound by changing the tonal
balance of the sound.
1
2
Press SYSTEM MENU.
Press NIGHT.
Press X/x repeatedly until “AUDIO
MENU” appears in the front panel
“NIGHT ON” appears in the front panel display
and the sound effect is activated.
During the night mode is on, “NIGHT” lights up
in the front panel display.
display, then press
or c.
3
4
Press X/x repeatedly until “TONE”
appears in the front panel display, then
Note
press
Press X/x to select the desired setting,
then press
or c.
• When sound is output from the center speaker, this
effect is more pronounced, as speech (movie dialog,
etc.) is easy to hear. When sound is not output from
the center speaker, or you are using the headphones,
the system optimally adjusts the volume.
.
• “BASS”: You can adjust the bass
frequencies.
• “TREBLE”: You can adjust the treble
frequencies.
To turn off the sound effect
Press NIGHT so that “NIGHT” disappears from
the front panel display.
5
Press X/x to adjust the sound.
The adjusted value appears in the front
panel display. You can set the value from
–6 to +6.
6
7
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
US
50
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Select the radio station.
Automatic tuning
Tuner
Press and hold TUNING +/– until the auto
scanning starts.
Listening to the Radio
You can enjoy radio sound with the system’s
[Auto Tuning] appears on the TV screen.
Scanning stops when the system tunes in a
station.
speakers.
To stop the automatic tuning manually,
press TUNING +/– or x.
"/1
“TUNED” and “ST” (for stereo program)
light up in the front panel display.
1
4
7
2
5
8
0
3
6
9
Number
buttons
Manual tuning
CLEAR
SYSTEM
MENU
Press TUNING +/– repeatedly.
D.TUNING
3
Adjust the volume by pressing
VOLUME +/–.
C/X/x/c,
HOME
OPTIONS
To turn off the radio
FUNCTION
PRESET +/–
Press "/1.
TUNING +/–
x
To change the AM tuning interval
DISPLAY
1
Press FUNCTION repeatedly until
“TUNER AM” appears in the front panel
display.
VOLUME
+/–
Current station
Current band and preset number
2
Press and hold N and FUNCTION on
the unit until “AM 9K STEP” or “AM
10K STEP” appears in the front panel
display.
FM
7
Tip
88.00 MHz
• To improve reception, reorient the connected
antennas (aerials).
SONY RADIO
Available OPTIONS
1
Press OPTIONS.
Station name
The options menu appears.
Tip
2
Press X/x to select an item, then press
• You can operate the tuner function using the tuner
menu on the front panel display. See “Operating the
.
The available items differ depending on the
situation.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Items
Details
[Preset Memory] Preset 20 FM stations, 10 AM
stations.
[Direct Tuning]
[FM Mode]
Input station frequency directly.
Select monaural or stereo
reception of FM programs.
US
51
Download from Www.Somanuals.com. All Manuals Search And Download.
To view the station name or
frequency in the front panel
display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency
using the front panel display.
Selecting the preset station
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
The last received station is tuned in.
Press DISPLAY.
2
Press PRESET +/– repeatedly to select
the preset station.
Each time you press DISPLAY on the remote,
the display changes as shown.
1 Station name*
2 Frequency**
* This is displayed if you have entered a name for a
The preset number and frequency appear on
the TV screen and front panel display.
Each time you press the button, the system
tunes in one preset station.
preset station.
**Returns to the original display after several seconds
have elapsed.
Tip
• You can select the preset station number directly
by pressing the number buttons.
Presetting radio stations
Selecting a radio station by
inputting a frequency directly
You can preset 20 FM stations, and 10 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
When you know the frequencies, you can select
radio stations by inputting the frequencies
directly.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
2
Press and hold TUNING +/– until the
auto scanning starts.
[Auto Tuning] appears on the TV screen.
Scanning stops when the system tunes in a
station.
2
Press OPTIONS.
The options menu appears.
“TUNED” and “ST” (for stereo program)
light up in the front panel display.
3
4
5
Press X/x to select [Direct Tuning],
then press
.
3
Press OPTIONS.
Press the number buttons to select the
frequencies.
The options menu appears.
Press
.
4
5
6
Press X/x to select [Preset Memory],
then press
.
The setting is made.
Press X/x to select the preset number
you want.
Press
.
The setting is made.
To change the preset number
Select the desired preset number by pressing
PRESET +/–, then perform the procedure from
Step 3.
US
52
Download from Www.Somanuals.com. All Manuals Search And Download.
To operate by using D.TUNING
Operating the tuner function
using the system menu
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
You can operate the tuner function using the
system menu on the front panel display.
2
Press D.TUNING.
To preset radio stations
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
3
4
Press the number buttons to select the
frequencies.
Press
.
2
Press and hold TUNING +/– until the
auto scanning starts.
If an FM program is noisy
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (for stereo
program) light up in the front panel display.
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “TUNER
MENU” appears in the front panel
1
Press OPTIONS.
The options menu appears.
display, then press
or c.
2
3
Press X/x to select [FM Mode], then
5
6
7
Press X/x repeatedly until “MEMORY”
appears in the front panel display, then
press
.
Press X/x to select [Monaural].
• [Stereo]: Stereo reception.
press
or c.
A preset number appears in the front panel
display.
• [Monaural]: Monaural reception.
4
Press
.
TUNED ST
The setting is made.
Press X/x to select the preset number
you want.
TUNED ST
Tip
• You can select the preset number directly by
pressing the number buttons.
Press
.
“COMPLETE” appears in the front panel
display, and the station is stored.
8
9
Repeat Steps 2 to 8 to store other
stations.
Press SYSTEM MENU.
The system menu turns off.
US
53
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the preset number
To name preset stations
You can enter a name for preset stations. These
names (for example, “ABC”) appear in the front
panel display when a station is selected.
Only one name can be entered for each preset
station.
Select the desired preset number by pressing
PRESET +/–, then perform the procedure from
Step 3.
If an FM program is noisy
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
The last received station is tuned in.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “TUNER
MENU” appears in the front panel
display, then press
2
Press PRESET +/– repeatedly to select
the preset station you want to create an
index name for.
or c.
3
Press X/x repeatedly until “FM MODE”
appears in the front panel display.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “TUNER
MENU” appears in the front panel
TUNED ST
display, then press
or c.
5
Press X/x repeatedly until “NAME IN”
appears in the front panel display.
4
5
Press
or c.
Press X/x to select “MONO.”
• “STEREO”: Stereo reception.
• “MONO”: Monaural reception.
TUNED ST
6
7
Press
or c.
6
7
Press
.
Create a name by using C/X/x/c.
The setting is made.
Press X/x to select a character, then press c
to move the cursor to the next position.
Press SYSTEM MENU.
The system menu turns off.
TUNED ST
You can input letters, numbers, and other
symbols for a radio station.
If you make a mistake
Press C/c repeatedly until the character to
be changed flashes, then press X/x to select
the desired character.
To erase the character, press C/c
repeatedly until the character to be erased
flashes, then press CLEAR.
8
9
Press
.
“COMPLETE” appears in the front panel
display, and the station name is stored.
Press SYSTEM MENU.
The system menu turns off.
US
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing the connected
component on the system
External Audio Device
Using the DIGITAL MEDIA
PORT Adapter
1
Press FUNCTION repeatedly until
“DMPORT” appears in the front panel
display.
The DIGITAL MEDIA PORT (DMPORT)
adapter is for enjoying sound from a portable
audio source or computer. By connecting a
DIGITAL MEDIA PORT adapter, you can
enjoy sound from the connected component on
the system.
Available DIGITAL MEDIA PORT adapters
vary in each area.
For details on connecting the DIGITAL MEDIA
PORT adapter, see “Connecting the other
2
Start playback of the connected
component.
The sound and images from the connected
component are played on the system or
connected TV.
For operation details, refer to the operating
instructions of the DIGITAL MEDIA
PORT adapter.
Tip
• Depending on the type of DIGITAL MEDIA PORT
adapter, you may be able to operate a connected
component using either the buttons on the remote or
the unit. The following illustration shows an example
of buttons that can be used in this case.
Note
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is
turned on.
• Depending on the type of DIGITAL MEDIA PORT
adapter, images are also output. In this case, the
system outputs a composite video signal only,
regardless of the type of video signal.
1
4
7
2
5
8
0
3
6
9
• When you use the system and a Bluetooth Wireless
Audio Adapter (such as TDM-BT1, not supplied) at
the same time, transmission distance between the
Bluetooth transmitter and Bluetooth Wireless Audio
Adapter may be reduced. In this case, place the
Bluetooth transmitter as far as possible from the
system, or move the Bluetooth Wireless Audio
Adapter closer to the Bluetooth transmitter.
• When you use the system and the Wireless Network
Audio Adapter (such as TDM-NC1, not supplied) at
the same time, place the Wireless Network Audio
Adapter as far as possible from the system.
FUNCTION
./>
N
x
X
To enhance compressed sound
You can enhance compressed sound such as an
MP3 audio file. This effect is activated
automatically when you set the decoding mode
“DMPORT” function is selected. To cancel the
effect, select other than “A.F.D. STD.”
US
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the wireless
transmitter/transceiver
Using an S-AIR Product
The unit is compatible with the S-AIR function
(page 116), which allows sound transmission
between S-AIR products.
When you purchase the S-AIR product, you
need to perform the following settings to
establish the sound transmission.
To make use of the S-AIR function, you need to
insert the wireless transmitter into the unit and
the wireless transceiver into the S-AIR sub unit.
Note
• When you insert the wireless transmitter/transceiver,
make sure that the AC power cord (mains lead) is not
connected to a wall outlet (mains).
• Do not touch the terminals of the wireless transmitter/
transceiver.
About S-AIR products
There are two types of S-AIR product.
• S-AIR main unit (this unit): This is for
transmitting sound. You can use up to three
S-AIR main units. (The number of usable
S-AIR main units depends on the use
environment.)
To insert the wireless transmitter
into the unit
1
Remove the screws and detach the slot
cover.
• S-AIR sub unit: This is for receiving sound.
– Surround amplifier: You can enjoy
surround speaker sound wirelessly.
Rear of the unit
COMPONENT VIDEO OUT
VIDEO OUT
ANTENNA
COAXIAL 75
EZW-T100
– S-AIR receiver: You can enjoy system
sound in another room.
Y
P
B
/
C
B
PR
/
C
R
FM
HDMI OUT
AM
TV
AUDIO
SAT/CABLE
DIGITAL IN
TV
E
A MAX
LAN(100)
DIGITAL IN
DC5V
L
L
SPEAKER
DMPORT
DC5V
700mA MAX
SPEAKER
A. CAL MIC
ECM-AC2
R
R
CENTER SUBWOOFER
FRONT
R
FRONT
L
SUR
R
SUR
L
AUDIO IN
AUDIO IN
COAXIAL
OPTICAL
Room A
S-AIR main unit
Slot cover
-T100
EZW
S-AIR sub unit
(surround amplifier)
Note
• Remove the screws from the slot cover bearing
the caution mark. Do not remove other screws.
• The slot cover is no longer necessary; however,
keep it after detaching.
Room B
S-AIR sub unit
(S-AIR receiver)
(not supplied)
US
56
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Insert the wireless transmitter.
Tip
• When you change the S-AIR configuration, Sony
recommends that you perform [Auto Calibration].
For details, see “Calibrating the Appropriate Settings
Rear of the unit
COMPONENT VIDEO OUT
VIDEO OUT
ANTENNA
COAXIAL 75
EZW-T100
Y
PB
/
C
B
PR
/
C
R
FM
HDMI OUT
AM
TV
AUDIO
SAT/CABLE
DIGITAL IN
TV
E
A MAX
LAN(100)
DIGITAL IN
DC5V
L
L
SPEAKER
DMPORT
DC5V
700mA MAX
SPEAKER
A. CAL MIC
ECM-AC2
R
R
CENTER SUBWOOFER
FRONT
R
FRONT
L
SUR
R
SUR
L
AUDIO IN
AUDIO IN
COAXIAL
OPTICAL
Establishing sound
transmission between the unit
and S-AIR sub unit
(ID setting)
100
-T
ZW
E
For the surround amplifier
For the S-AIR receiver
Note
Simply by matching the ID of the unit and the
S-AIR sub unit, you can establish sound
transmission.
• Insert the wireless transmitter with the S-AIR
logo facing up.
• Insert the wireless transmitter so that the V
marks are aligned.
To set the ID of the unit
• Do not insert anything other than the wireless
transmitter into the EZW-T100 slot.
1
Press "/1 on the unit.
The system turns on.
3
Make sure to use the same screws to
secure the wireless transmitter.
2
3
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
Rear of the unit
COMPONENT VIDEO OUT
VIDEO OUT
ANTENNA
COAXIAL 75
EZW-T100
Y
PB
/
C
B
PR
/
C
R
FM
display, then press
or c.
HDMI OUT
AM
TV
AUDIO
SAT/CABLE
DIGITAL IN
TV
E
A MAX
LAN(100)
DIGITAL IN
DC5V
L
L
SPEAKER
DMPORT
DC5V
700mA MAX
SPEAKER
A. CAL MIC
ECM-AC2
R
R
CENTER SUBWOOFER
FRONT
R
FRONT
L
SUR
R
SUR
L
AUDIO IN
AUDIO IN
COAXIAL
OPTICAL
4
Press X/x repeatedly until “S-AIR ID”
appears in the front panel display, then
press
or c.
0
0
1
-T
W
Z
Note
E
• When the wireless transmitter is not inserted in
the unit, “S-AIR ID” cannot be selected.
5
6
7
8
Press X/x to select the desired ID.
You can select any ID (A, B, or C).
Press
.
Note
The setting is made.
• Do not use other screws to fasten the wireless
transmitter.
Press SYSTEM MENU.
The system menu turns off.
To insert the wireless
transceiver into the S-AIR sub
unit
For details on installing the wireless transceiver
into the S-AIR sub unit, such as a surround
amplifier or S-AIR receiver, see the operating
instructions of the S-AIR sub unit.
Set the S-AIR sub unit to the same ID.
Sound transmission is established as
follows (example):
US
57
Download from Www.Somanuals.com. All Manuals Search And Download.
S-AIR main unit
(This unit)
Enjoying the system’s sound in
another room
ID A
For the S-AIR receiver
You can enjoy the system’s sound by using the
S-AIR receiver. The S-AIR receiver can be
placed in another room for enjoying the
system’s sound there.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
For details of the S-AIR receiver, refer to the
operating instructions of the S-AIR receiver.
1
2
Press SYSTEM MENU.
To set the ID of the surround
amplifier
Refer to the operating instructions of the
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
display, then press
or c.
surround amplifier.
3
Press X/x repeatedly until “S-AIR
MODE” appears in the front panel
To set the ID of the S-AIR
receiver
display, then press
or c.
Refer to the operating instructions of the S-AIR
Note
receiver.
• When the wireless transmitter is not inserted in
the unit, “S-AIR MODE” cannot be selected.
To use multiple S-AIR main units
You can use multiple S-AIR main units by
setting a different ID for each component.
4
Press X/x to select the desired setting.
• “PARTY”: The S-AIR receiver outputs
sound according to functions set on the
unit.
• “SEPARATE”: You can set the desired
function for the S-AIR receiver while unit
functions do not change.
S-AIR main unit
Other S-AIR
(This unit)
main unit
ID B
ID A
5
6
7
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
Select the desired function on the
S-AIR receiver.
x When “PARTY” is set
ID A
S-AIR
sub unit
ID B
S-AIR sub unit
ID A
S-AIR sub unit
The S-AIR receiver’s function changes
sequentially as you press FUNCTION of
S-AIR receiver.
x When “SEPARATE” is set
The S-AIR receiver’s function changes
by pressing S-AIR CH of the S-AIR
receiver as follows.
US
58
Download from Www.Somanuals.com. All Manuals Search And Download.
“MAIN UNIT” t “TUNER FM” t
“TUNER AM” t “DMPORT” t
“AUDIO” t …
Enjoying the S-AIR receiver
while the unit is in standby
mode
To enjoy the same function as the unit,
select “MAIN UNIT.”
For the S-AIR receiver
When “TUNER FM” or “TUNER AM” is
selected on the unit, you can only select the
same band on the S-AIR receiver. When
other than “TUNER FM” or “TUNER AM”
is selected on the unit, you can select any
band for the tuner on the S-AIR receiver.
You can enjoy the S-AIR receiver while the unit
is in standby mode by setting “S-AIR STBY” to
“STBY ON.”
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
8
Adjust the volume on the S-AIR
receiver.
display, then press
or c.
Note
3
Press X/x repeatedly until “S-AIR
STBY” appears in the front panel
• When the sound is other than 2 channel stereo, multi-
channel sound is downmixed to 2 channel.
• The sound of the S-AIR receiver may be cut off by
operation of the unit.
display, then press
or c.
Note
• When the wireless transmitter is not inserted in
the unit, “S-AIR STBY” cannot be selected.
To set “S-AIR MODE” via the
remote
4
Press X/x to select the desired setting.
Press S-AIR MODE.
• “STBY ON”: You can enjoy the S-AIR
receiver while the unit is in standby mode
or turned on. The power consumption
during standby mode increases.
• “STBY OFF”: You cannot enjoy the
S-AIR receiver while the unit is in
standby mode.
The S-AIR mode appears in the front panel
display. Each time you press S-AIR MODE, the
S-AIR mode changes.
To control the system from the
S-AIR receiver
You can control the system from the S-AIR
5
Press
.
receiver by using the following buttons.
The setting is made.
Press
Operation
6
Press SYSTEM MENU.
N, X, x,
./>
Share the same operations on the
remote and unit.
The system menu turns off.
Note
S-AIR CH
Change the function of the system.
• When you turn the system off while “S-AIR STBY”
is set to “STBY ON,” “S-AIR” flashes (when sound
transmission between the unit and S-AIR receiver is
not established), or lights up (when sound
For details, refer to the operating instructions of
the S-AIR receiver.
transmission between the unit and S-AIR receiver is
established) in the front panel display.
US
59
Download from Www.Somanuals.com. All Manuals Search And Download.
x After pairing
Sound transmission is established between the
paired unit and S-AIR sub unit(s) only.
Identifying the unit with a
specific S-AIR sub unit
(Pairing operation)
For the surround amplifier
For the S-AIR receiver
Your room
This unit
Neighbor
ID A
No transmission
It is easy to set the same ID for the unit and an
S-AIR sub unit, such as a surround amplifier or
S-AIR receiver, to establish sound transmission.
However, neighbors may also receive your
system’s sound if IDs are the same, or you may
receive sound from neighbors. To prevent this,
you can identify the unit with a specific S-AIR
sub unit by performing the pairing operation.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
x Before pairing
Pairing
Sound transmission is established by the ID
(example).
To perform pairing
Your room
This unit
Neighbor
1
Place the S-AIR sub unit that you want
to pair near the unit.
Note
• Remove headphones from the surround
amplifier (if connected).
ID A
2
Match the IDs of the unit and the S-AIR
sub unit.
• To set the ID of the unit, see “To set the ID
• To set the ID of the S-AIR sub unit, refer
to the operating instructions of the S-AIR
sub unit.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
display, then press
or c.
5
Press X/x repeatedly until “PAIRING”
appears in the front panel display, then
press
or c.
Note
• When the wireless transmitter is not inserted in
the unit, “PAIRING” cannot be selected.
US
60
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Press X/x repeatedly until “START”
appears in the front panel display, then
Checking the S-AIR status of
the unit
press
.
The unit starts pairing and “SEARCH”
flashes in the front panel display.
You can check the S-AIR status such as the
S-AIR ID or pairing information.
To cancel pairing, press SYSTEM MENU.
Start pairing of the S-AIR sub unit.
1
2
Press SYSTEM MENU.
x For the surround amplifier
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
Press POWER on the surround amplifier to
turn on the surround amplifier and press
PAIRING on the rear panel of the surround
amplifier.
display, then press
or c.
3
Press X/x repeatedly until “S-AIR ID”
appears in the front panel display, then
The PAIRING indicator of the surround
amplifier flashes red when pairing starts.
When sound transmission is established,
the PAIRING indicator of the surround
amplifier turns red and “PAIRING” and
“COMPLETE” appear alternately in the
front panel display.
press
or c.
The S-AIR ID of the unit appears in the
front panel display. When the unit is paired,
“(PAIRING)” appears beside ID.
4
Press SYSTEM MENU.
The system menu turns off.
Tip
• To press PAIRING on the rear panel of the
surround amplifier, a slim instrument, such as a
paper clip, can be used.
If sound transmission is
unstable
For the surround amplifier
For the S-AIR receiver
x For the S-AIR receiver
Refer to the operating instructions of the
S-AIR receiver.
When sound transmission is established,
“PAIRING” and “COMPLETE” appear
alternately in the front panel display.
If you use multiple wireless systems which share
the 2.4 GHz band, such as wireless LAN or
Bluetooth, the transmission of S-AIR products
or other wireless systems may be unstable. In
this case, the transmission may be improved by
changing the following “RF CHANGE” setting.
Note
• Perform pairing within several minutes of Step
5. If you do not, “PAIRING” and
“INCOMPLETE” appear alternately in the front
1
2
Press SYSTEM MENU.
panel display. To continue pairing, press
and
start again from Step 5. To cancel pairing, press
SYSTEM MENU.
Press X/x repeatedly until “S-AIR
MENU” appears in the front panel
display, then press
or c.
8
Press SYSTEM MENU.
The system menu turns off.
3
Press X/x repeatedly until “RF
CHANGE” appears in the front panel
Note
display, then press
or c.
• When you perform pairing, “(PAIRING)” appears
beside ID on the display for selecting ID.
Note
• When the wireless transmitter is not inserted in
the unit, “RF CHANGE” cannot be selected.
To cancel pairing
Change the ID setting of the unit by using the
S-AIR ID switch of the unit. If you select a new
ID, pairing is canceled.
US
61
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press X/x to select the desired setting.
• “AUTO”: Normally select this. The
system changes “RF CHANGE” to “ON”
or “OFF” automatically.
• “ON”: The system transmits sound by
searching for a better channel for
transmitting.
• “OFF”: The system transmits sound by
fixing the channel for transmitting.
5
6
7
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
When you set “RF CHANGE” to “OFF,”
select the ID so that sound
Note
• In most cases, you will not need to change this
setting.
– If “RF CHANGE” is set to “OFF,” transmission
between the unit and S-AIR sub unit can be
performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing the
transmission channel (frequency) of the other
wireless system(s). For details, refer to the operating
instructions of the other wireless system(s).
US
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the connected component, the Control
for HDMI function may not work. Refer to the
operating instructions supplied with the component.
• The Control for HDMI function may not work if you
connect a component other than Sony, even if the
component is compatible with the Control for HDMI
function.
Other Operations
Using the Control for
HDMI Function for
“BRAVIA” Sync
Preparing for the Control for
HDMI function
This function is available on TVs with the
“BRAVIA” Sync function only.
By connecting Sony components that are
compatible with the Control for HDMI function
with an HDMI cable, operation is simplified as
below:
(Control for HDMI - Easy Setting)
The system is compatible with the Control for
HDMI - Easy Setting function. If the TV is
compatible with the Control for HDMI - Easy
Setting function, you can set the system’s
[Control for HDMI] function automatically by
setting the TV. For details, refer to the operating
instructions of the TV.
If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control
for HDMI function of the system and TV
manually.
Control for HDMI is a mutual control function
standard used by CEC (Consumer Electronics
Control) for HDMI (High-Definition
Multimedia Interface).
Note
• For details on setting the TV, refer to the operating
instructions.
The Control for HDMI function will not work in
the following cases:
1
2
3
Make sure that the system and the TV
are connected with an HDMI cable.
– When you connect this system to a
component which is not compatible with the
Control for HDMI function.
Turn on the TV and press [/1 to turn on
the system.
– A component does not have an HDMI jack.
Switch the input selector on your TV so
that the signal from the system through
the HDMI input appears on the TV
screen.
There are convenient buttons on the system’s
remote for operating the TV, such as
THEATER, ONE-TOUCH PLAY, and TV "/1.
For details, see “Controlling Your TV with the
Supplied Remote” (page 69) and refer to the
operating instructions of the TV.
4
Set the Control for HDMI function of the
system and TV.
The Control for HDMI function for system
and TV is simultaneously set to on.
ONE-TOUCH
PLAY
TV
THEATER
BRAVIA Sync
S-AIR
MODE NIGHT BASS
DYNAMIC
TV
US
63
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the [Control for HDMI]
function of the system to on/off
manually
Watching BD/DVD by a single
button press
1
Press HOME.
(One-Touch Play)
The home menu appears on the TV screen.
By only pressing ONE-TOUCH PLAY, the TV
turns on, the TV is set for BD/DVD input
selector, and the system starts playing a disc
automatically.
2
3
Press C/c to select
Press X/x to select [HDMI Settings],
then press
[Setup].
.
Also, when you insert a disc, One-Touch Play is
enabled. If One-Touch Play does not start (in the
case of inserting a disc that is not compatible
with the auto playback function), press N or
ONE-TOUCH PLAY.
The options for [HDMI Settings] appear.
4
5
Press X/x to select [Control for HDMI],
then press
Press X/x to select the setting, then
press
.
.
The system and TV work as follows (e.g.):
• [On]: On.
• [Off]: Off.
This system
TV
Note
Turns on. (If not already Turns on. (If not already
• During the setting of the Control for HDMI function
for the system, the System Audio Control function
does not work.
turned on.)
turned on.)
r
r
Switches to “BD/DVD” Switches to HDMI input.
function.
r
Tip
r
• The default setting of the Control for HDMI function
of the system is [On].
Minimizes sound level.
Starts playing the disc and
outputs the sound.
(System Audio Control)
Using the Theater Mode
Turning the system off in sync
with the TV
(Theater Mode)
If your TV is compatible with the Theater mode,
when you press THEATER, you can enjoy the
optimum video mode and sound quality suited
for movies, and TV sound is output from the
system’s speakers automatically. Also, the TV’s
video mode switches to Theater Mode.
(System Power Off)
When you turn the TV off by using the POWER
button on the TV’s remote or TV "/1 on the
system’s remote, the system turns off
automatically.
Note
• Before using the System Power Off function, set the
function for TV power. For details, refer to the
operating instructions of the TV.
• Depending on the status, the system or the connected
components may not turn off automatically. For
details, see the operating instructions supplied with
the connected components.
US
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying TV sound from the
speakers in this system
Changing the language for the
on-screen display of the TV
(System Audio Control)
(Language Follow)
You can enjoy TV sound in this system by easy
operation.
To use this function, connect the system and the
TV with an audio cord and an HDMI cable
When you change the language for the on-screen
display of the TV, the system’s on-screen
display language is also changed after turning
the system off and on.
You can use the System Audio Control function
as follows:
• You can enjoy TV sound from the speakers of
the system by means of a simple operation. For
details, see the operating instructions of the
TV.
• When the system is turned on, TV sound will
be output from the speakers of the system.
• When TV sound is output from the speakers of
the system, you can adjust the volume and turn
off the sound of the system using the TV
remote.
Note
• While the TV is in PAP (picture and picture) mode,
the System Audio Control function will not work.
When the TV exits PAP mode, the output method of
the TV returns to the one before PAP mode.
Setting the Maximum Volume
Level of the System
(Volume Limit)
If you change the output method of the TV to the
system speaker on the TV menu or by pressing
THEATER, loud sound may be output
depending on the volume level of the system.
You can prevent this by limiting the maximum
level of the volume. For details, see [Volume
US
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibrating the
Appropriate Settings
Automatically
[Auto Calibration]
A
N
5
N
7
E
T
N
X
A
A
L
IA
O
C
M
F
0
0
1
-T
W
Z
E
M
C
A
IO
D
U
A
IC
M
L
A
V
T
L
.
A
2
C
-A
M
C
E
L
R
T
EX
X
A
M
A
m
0
0
5
DC5V
R
V
T
N
I
IO
D
U
A
E
IN
L
L
A
B
A
IT
/C
IG
T
D
IN
A
I
O
S
D
U
A
IN
L
A
IT
IG
D
L
A
TIC
P
O
L
IA
X
A
O
C
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
Note
• The system outputs a loud test sound when [Auto
Calibration] starts. You cannot turn the volume
down. Give consideration to children and neighbors.
Calibration mic
1
Press HOME.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Audio Settings],
then press
Press X/x to select [Auto Calibration],
then press
[Setup].
.
4
.
6
7
Press X/x to select [Start].
The confirmation display for [Auto
Calibration] appears.
To cancel, select [Cancel].
5
Connect the calibration mic to the
A.CAL MIC jack on the rear panel.
Press
.
[Auto Calibration] starts.
Set up the calibration mic at ear level using
a tripod, etc. (not supplied). The front of
each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic.
The system adjusts the speaker settings
automatically.
Be quiet during the measurement.
Note
• Before [Auto Calibration], make sure that the
surround amplifier turns on and you install the
surround amplifier in the appropriate location. If
you install the surround amplifier in an improper
location, such as another room, proper
measurement will not be obtained.
• When you use the Wireless Surround Speaker
Kit (WAHT-SBP1, optional) for the surround
appropriate location and turn the surround
amplifier on.
• Loud test sound is output when [Auto
Calibration] starts. You cannot turn the volume
down. Give consideration to children and
neighbors.
US
66
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Confirm the conclusions of [Auto
Calibration].
Setting the Speakers
[Speaker Settings]
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
The conclusions appear on the TV screen.
Press C/c to change the page. The first page
shows the distance of speakers. The second
page shows the level of speakers.
Note
• If measurement fails, follow the message then
retry [Auto Calibration].
Tip
1
Press HOME.
• You can change a measurement unit (feet or
meters) by pressing the color button (RED).
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Audio Settings],
then press
Press X/x to select [Speaker Settings],
then press
[Setup].
9
Press X/x to select [OK] or [Cancel],
then press
.
.
x The measurement is OK.
Disconnect the calibration mic, then select
[OK]. The result is implemented.
4
.
The [Speaker Settings] display appears.
x The measurement is not OK.
Follow the message, then select [OK] to
retry.
5
Press X/x to select the item, press
.
Setup the following settings.
Note
• While the Auto Calibration function works:
– do not turn off the power.
x [Connection]
If you do not connect center or surround
speakers, set the parameters for [Center] and
[Surround]. Since the front speaker and
subwoofer settings are fixed, you cannot change
them.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
– do not insert or eject a disc.
– do not connect the headphones to the surround
amplifier.
When you use the Wireless Surround Speaker
Kit (WAHT-SBP1, optional) for the surround
also.
– do not disconnect the calibration mic.
[Front]
[Yes]
[Center]
[Yes]: Normally select this.
[None]: Select this if no center speaker is used.
[Surround]
[Yes]: Normally select this.
[None]: Select this if no surround speaker is
used.
[Surround Back]
[Yes]: Select this if surround back speakers are
used.
[None]: Select this if no surround back speaker
is used.
US
67
Download from Www.Somanuals.com. All Manuals Search And Download.
[Subwoofer]
Tip
[Yes]
• You can change a measurement unit (feet or meters)
by pressing the color button (RED).
x [Distance]
When you move the speakers, be sure to set the
parameters of the distance (A) from the
listening position to the speakers.
You can set the parameters from 0 to 23 feet (0.0
to 7.0 meters).
x [Level]
You can adjust the sound level of the speakers.
You can set the parameters from –6.0 dB to +6.0
dB. Be sure to set [Test Tone] to [On] for easy
adjustment.
The speakers in the illustration correspond to the
following:
[Front Left/Right] 0.0 dB: Set the front speaker
level.
1Center speaker
2Front left speaker (L)
3Front right speaker (R)
4Subwoofer
5Surround left speaker (L)
6Surround right speaker (R)
7Surround back left speaker (L) (optional)
8Surround back right speaker (R) (optional)
[Center]* 0.0 dB: Set the center speaker level.
[Surround Left/Right]* 0.0 dB: Set the surround
speaker level.
[Surround Back Left/Right]* 0.0 dB: Set the
surround back speaker level.
[Subwoofer] 0.0 dB: Set the subwoofer level.
* This item appears when you set to [Yes] in the
[Connection] setting.
1
2
3
x [Test Tone]
The speakers will emit a test tone to adjust
[Level].
4
[Off]: The test tone is not emitted from the
speakers.
A
[On]: The test tone is emitted from each speaker
in sequence while adjusting level. When you
select one of the [Speaker Settings] items, the
test tone is emitted from each speaker in
sequence.
5
6
A
Adjust the sound level as follows.
7
8
1
2
Set [Test Tone] to [On].
[Front Left/Right] 10 ft/3.0 m: Set the front
speaker distance.
[Center]* 10 ft/3.0 m: Set the center speaker
distance.
[Surround Left/Right]* 10 ft/3.0 m: Set the
surround speaker distance.
[Surround Back Left/Right]* 10 ft/3.0 m: Set the
surround back speaker distance.
[Subwoofer] 10 ft/3.0 m: Set the subwoofer
distance.
Press X/x to select [Level], then press
.
3
4
Press X/x to select the desired speaker
type, then press
.
Press C/c to select the left or right
speaker, then press X/x to adjust the
level.
5
6
7
Press
.
* This item appears when you set to [Yes] in the
[Connection] setting.
Repeat Steps 3 to 5.
Press RETURN.
Note
The system returns to the previous display.
• Depending on the input stream, [Distance] may not
be effective.
8
Press X/x to select [Test Tone], then
press
.
US
68
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Press X/x to select [Off], then press
.
Controlling Your TV with
the Supplied Remote
Note
• The test tone signals are not output from the HDMI
OUT jack.
By adjusting the remote signal, you can control
your TV with the supplied remote.
Tip
• To adjust the volume of all the speakers at one time,
press VOLUME +/–.
Note
• When you replace the batteries of the remote, the
code number may reset itself to the default (SONY)
setting. Reset the appropriate code number.
Preparing the remote for
controlling the TV
Press and hold TV [/1 while entering your
TV’s manufacturer’s code (see the table)
using the number buttons. Then release TV
[/1.
If you successfully set the manufacturer’s code,
the TV button flashes twice slowly. If the setting
is unsuccessful, the TV button flashes five times
quickly.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
code that works with your TV.
Manufacturer
SONY
Code number
501 (default), 502
DAEWOO
EMERSON
FUNAI
506
567
548
GE
509
GOLDSTAR/LG
GRUNDIG
HITACHI
ITT
503, 517, 544, 568
533
514
521, 522
516
JVC
LOEWE
518
MITSUBISHI/MGA 527
NEC
503
NOKIA
521, 522, 573, 575
553, 572
PANASONIC
PHILIPS
PIONEER
515, 518, 557, 570
526
US
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer
RADIO SHACK
RCA/PROSCAN
SABA
Code number
565
By pressing
You can
Number buttons, Select the TV channel.
, ENTER
510
HOME
FAVORITES
CC
Display the menu of the TV.
Display the favorite channel list.
Display closed captioning.
530, 537, 558
SAMSUNG
515, 517, 544, 566, 569, 571,
574
SANYO
508, 545
535, 565
547, 558
547, 549
541, 551
543
GUIDE
Display the Digital Electronic
Programme Guide (EPG).
SHARP
TOOLS
Display the operation menu for the
current display.
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
RETURN
Return to the previous channel or
layer on the menu of the TV.
Input “.” (dot) when inputting
numerics.
WIDE
Change the aspect ratio of the
connected TV.
Controlling the TV with the
remote
C/X/x/c,
Select the item on the menu.
Display the information.
DISPLAY
You can control the TV using the following
buttons. To use these buttons (other than
THEATER, TV [/1, TV INPUT), set the
remote to the TV mode by pressing TV, so that
TV lights up for 1 second.
Tip
• The function of these buttons are same as the remote
buttons of the SONY TV. For details, refer to the
operating instructions of the TV.
To exit the TV mode, press TV so that TV
flashes four times.
Note
• While in the TV mode, if you press any of the
following buttons, TV lights up. (Depending on the
manufacturer setting, some buttons may not work,
and TV does not light up.)
• When you press other than the following buttons
while the remote is in the TV mode, TV flashes four
times and the remote exits the TV mode
automatically, and the system is operated as the
function of the pressed button.
• Depending on the TV, you may not be able to use
some or all of the buttons.
By pressing
TV "/1
You can
Turn the TV on or off.
THEATER
Enjoy optimal images and sound
suited for movies.
TV INPUT
Switch the TV’s input source
between the TV and other input
sources.
VOLUME +/–
CH +/–
Adjust the TV volume.
Select the TV channel.
MUTING
Turn off the TV sound
temporarily.
US
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
You can preset the time in 10-minute
increments.
Changing the Brightness
of the Front Panel
Display
The brightness of the front panel display can be
set to either of 2 levels.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “SLEEP
MENU” appears in the front panel
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DISP
MENU” appears in the front panel
display, then press
or c.
3
Press X/x to select a setting.
display, then press
or c.
The minutes display (the remaining time)
changes by 10 minutes.
3
4
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press
or c.
Tip
• You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
Press X/x to select the brightness of
the front panel display.
• “DIMMER OFF”: Bright.
• “DIMMER ON”: Dark.
4
5
Press
.
The setting is made and “SLEEP” flashes in
the front panel display.
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
Press SYSTEM MENU.
The system menu turns off.
The system menu turns off.
US
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Deactivating the Buttons About the demonstration
on the Unit
(Child Lock)
You can turn on/off the demonstration in the
front panel display while the system is in
standby mode.
You can deactivate the buttons on the unit
(except for "/1) for preventing misoperation,
such as child mischief (child lock function).
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DISP
MENU” appears in the front panel
display, then press
Press x on the unit for more than 5
seconds.
or c.
3
4
Press X/x repeatedly until “DEMO”
appears in the front panel display, then
“CHILD LOCK” and “ON” appear in the front
panel display.
The child lock function is activated and the
buttons on the unit are locked. (You can operate
the system by using the remote.)
press
or c.
Press X/x to select a setting.
• “DEMO ON”: On.
To cancel, press x for more than 5 seconds so
that “CHILD LOCK” and “OFF” appear in the
front panel display.
• “DEMO OFF”: Off.
The default setting differs depending on the
area.
Note
5
6
Tip
Press
.
• When you operate the buttons on the unit while the
child lock function is on, “CHILD LOCK” appears in
the front panel display.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
• When you purchase the system new, or if the system
turn off the demonstration simply by pressing [/1 on
the remote.
US
72
Download from Www.Somanuals.com. All Manuals Search And Download.
You can setup the following options.
Settings and Adjustments
Icon
Explanation
Updates the software of the
system.
Using the Setup Display
You can make various adjustments of items such
Makes the video settings
according to the type of
connecting jacks.
as picture and sound.
Select
(Setup) on the home menu when you
need to change the settings of the system.
Makes the audio settings
Note
according to the type of
connecting jacks.
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
Makes detailed settings for BD/
DVD playback.
1
2
Press HOME.
The home menu appears on the TV screen.
Makes the photo-related
settings.
Press C/c to select
[Setup].
Network Update
Makes the HDMI settings.
Setup
Video Settings
Makes the system-related
settings.
Audio Settings
BD/DVD Viewing Settings
Photo Settings
Makes detailed settings for
Internet and network.
3
Press X/x to select the setup category
Re-runs the Easy Setup to make
icon to change, then press
.
the basic settings.
Example: [Video Settings]
Resets the system to the factory
settings.
Setup
TV Type
4
Press X/x to select an item, then press
Set the screen aspect ratio of your TV.
Screen Format
Original
.
DVD Aspect Ratio
Cinema Conversion Mode
Letter Box
Auto
The options for the selected item appear.
Example: [TV Type]
Setup
TV Type
16:9
4:3
Screen Format
DVD Aspect Ratio
Cinema Conversion Mode
Options
US
74
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select a setting, then
press
.
[Network Update]
You can update and improve the functions of the
The setting is selected and setup is
complete.
The options for the selected item appear.
Example: [4:3]
system.
For information about update functions, refer to
the following website:
http://esupport.sony.com
Note
Setup
• Do not disconnect the AC power cord (mains lead) or
network cable while downloading or updating
software.
TV Type
4 : 3
Set the screen aspect ratio of your TV.
Screen Format
Oiginal
Letter Box
Auto
DVD Aspect Ratio
Cinema Conversion Mode
• All operations, including opening the disc tray, are
disabled while updating.
• Downloading times may differ depending on the
server provider or line status.
Selected setting
• When error messages on network connections
appear, check the network connections using
[Network Diagnostic] of [Internet Settings] in
Tip
• The “UPDATE */9” counter (“*” indicates update
step) in the front panel display also shows progress of
the update.
• You can check the current software version by
selecting [System Information] in [System Settings]
• The [Setup] settings remain after updating.
• The system informs you of newer software version
information when [Software Update Notification] is
Updating the system’s
software using the network
1
Press X/x to select [Network Update],
then press
.
The unit connects to the network, and the
display asks for confirmation.
2
Press C/c to select [OK], then press
.
The unit starts downloading, then updating
the software automatically.
When updating finishes, “COMPLETE”
appears for 5 seconds in the front panel
display, then the system automatically turns
off.
US
75
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press "/1 to turn the system on.
The system starts up with the updated
software.
[Video Settings]
You can make the video settings according to
the type of connecting jacks.
Updating the system’s
software using an update disc
x [TV Type]
You can select the aspect ratio of the connected
TV.
You can update and improve the functions of the
system using an update disc provided by a Sony
dealer or local authorized Sony service facility.
[16:9]: Select this when connecting to a wide-
screen TV or a TV with a wide-mode function.
[4:3]: Select this when connecting to a 4:3
screen TV without a wide-mode function.
1
2
Insert the update disc.
The display asks for confirmation.
Select [OK], and press
.
x [Screen Format]
Software update starts.
You can select the display configuration for a
4:3 screen picture on a 16:9 wide-screen TV.
When updating finishes, “COMPLETE”
appears for 5 seconds in the front panel
display, then the system automatically turns
off.
[Original]: Select this when connecting to a TV
with a wide-mode function. Displays a 4:3
screen picture in 16:9 aspect ratio even on a
wide-screen TV.
[Fixed Aspect Ratio]: Changes the picture size
to fit the screen size with the original picture
aspect ratio.
3
4
Press "/1 to turn the system on.
The system starts up with the updated
software.
Press Z to remove the disc.
x [DVD Aspect Ratio]
You can select the display configuration for
playback of 16:9 screen pictures on a 4:3 screen
TV (selectable when [TV Type] is set to [4:3]
and [Screen Format] is set to [Fixed Aspect
Ratio]).
[Letter Box]: Displays a wide picture with black
bands on the top and bottom.
[Pan & Scan]: Displays a full-height picture on
the entire screen, with trimmed sides.
US
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
x [Cinema Conversion Mode]
You can set the video conversion method for
480p, 720p, 1080i, or 1080p* signals from the
HDMI OUT jack or the COMPONENT VIDEO
OUT jacks.
• If the picture is distorted or no picture appears,
wait for about 30 seconds without pressing any
buttons. The display returns to the resolution
setting screen.
• If the selected video output resolution is
incorrect, no picture appears on the screen when
you press any button in 30 seconds. In this case,
press and hold N and Z on the unit for more
than 5 seconds to reset the video output
resolution to the lowest resolution.
* HDMI only
[Auto]: Normally select this. The unit
automatically detects whether the material is
video-based or film-based, and switches to the
appropriate conversion method.
[Video]: The conversion method suited for
video-based material will always be selected
regardless of the material.
• When connecting the HDMI OUT jack and
other video output jacks at the same time, video
signals may not output from the jacks, other than
from the HDMI OUT jack, when [Auto] or
[1080p] is selected.
[HDMI Resolution]/[Component
Resolution]
x [Output Video Format]
You can select the jack type to output video
signals. For details, see “Video Output
[Auto] (HDMI only): Normally select this.
The unit outputs signals starting from the
highest resolution acceptable to the TV:
1080p > 1080i > 720p > 480p > 480i
If the resulting image format is undesirable,
try another setting that suits your TV.
[480i]: Outputs 480i video signals.
[480p]: Outputs 480p video signals.
[720p]: Outputs 720p video signals.
[1080i]: Outputs 1080i video signals.
[1080p] (HDMI only): Outputs 1080p
video signals.
1
Press X/x to select the jack type to
output video signals, then press
.
Note
• When connecting the HDMI OUT jack and
other video output jacks at the same time, select
[Component Video].
[TV Connection Method]
[HDMI]: Outputs signals from the HDMI
OUT jack according to the [HDMI
Resolution] setting below.
[Component Video]: Outputs signals from
the COMPONENT VIDEO OUT jacks
according to the [Component Resolution]
setting below.
[Video]: Outputs signals from the VIDEO
OUT jack.
x [BD-ROM 1080/24p Output]
You can set to output 1920 × 1080p/24 Hz video
signals when playing film-based materials on
BD-ROMs (720p/24 Hz or 1080p/24 Hz).
1920 × 1080p/24 Hz video signals can be output
when all of the following conditions are met.
– You connect a 1080/24p-compatible TV
using the HDMI OUT jack,
2
(When you select [HDMI] or
[Component Video])
Press X/x to select the signal type for
the HDMI OUT jack or COMPONENT
– [Output Video Format] is set to [HDMI], and
– [HDMI Resolution] is set to [Auto] or
[1080p].
VIDEO OUT jacks, then press
.
When you change the video output
The 24P indicator lights up when outputting
1920 × 1080p/24 Hz video signals.
resolution, a picture is displayed in the
selected resolution for about 30 seconds,
then the display asks for confirmation.
Follow the on-screen instructions.
“HD” lights up in the front panel display
when outputting 720p/1080i/1080p video
signals.
[Auto]: Outputs 1920 × 1080p/24 Hz video
signals only when connecting a 1080/24p-
compatible TV using the HDMI OUT jack.
[On]: Outputs 1920 × 1080p/24 Hz video
signals regardless of the connected TV type.
US
77
Download from Www.Somanuals.com. All Manuals Search And Download.
[Off]: Select this when your TV is not
compatible with 1080/24p video signals.
[Audio Settings]
Note
You can make the audio settings.
• Video signals may not be output when [BD-ROM
1080/24p Output] is set to [On].
x [BD Audio Setting]
You can select whether to mix or not mix the
interactive audio (button sound, effect sound,
etc.) and secondary audio (commentary) when
playing a BD that contains such audio.
x [YCbCr/RGB (HDMI)]
You can set the color setting for video signals
output from the HDMI OUT jack. Select the
setting that matches the connected TV type.
[Auto]: Automatically detects the type of
external device, and switches to the matching
color setting.
[Mix]: Outputs the audio obtained by mixing the
interactive audio and secondary audio to the
primary audio.
[YCbCr (4:2:2)]: Outputs YCbCr 4:2:2 video
signals.
[Direct]: Outputs the primary audio only.
[YCbCr (4:4:4)]: Outputs YCbCr 4:4:4 video
signals.
[RGB (16-235)]: Select this when connecting to
a device with an HDCP-compliant DVI jack.
[RGB (0-255)]: Select this when connecting to
an RGB (0-255) device.
x [Audio DRC] (BD/DVD VIDEO only)
You can compress the dynamic range of the
sound track. [Audio DRC] is useful for watching
movies at low volume late at night.
[Auto]: Performs playback at the dynamic range
specified by the disc (BD-ROM only).
[Off]: No compression of dynamic range.
[On]: The system reproduces the sound track
with the kind of dynamic range that the
recording engineer intended.
x [x.v.Color Output]
You can set whether to send xvYCC information
to the connected TV.
Combining xvYCC-compatible video with a TV
that supports x.v.Color display makes it possible
to more accurately reproduce object colors
present in the natural world.
x [Attenuate - TV]
Distortion may occur when you listen to a
component connected to the TV (AUDIO IN L/
R) jacks. You can prevent distortion by reducing
the input level on the unit. Distortion is not a
malfunction and will depend on the component
connected.
[Auto]: Normally select this.
[Off]: Select this when the picture is unstable or
colors appear unnatural.
x [Pause Mode] (BD/DVD VIDEO/DVD-R/
DVD-RW only)
You can select the picture in pause mode.
[On]: Attenuates the input level. The output
level is changed.
[Off]: Normal input level.
[Auto]: The picture, including subjects that
move dynamically, is output with no jitter.
Normally select this position.
[Frame]: The picture, including subjects that do
not move dynamically, is output in high
resolution.
US
78
Download from Www.Somanuals.com. All Manuals Search And Download.
x [Attenuate - AUDIO]
x [Sound Effect]
Distortion may occur when you listen to a
component connected to the AUDIO (AUDIO
IN L/R) jacks. You can prevent distortion by
reducing the input level on the unit. Distortion is
not a malfunction and will depend on the
component connected.
You can set the system’s sound effects (SOUND
MODE, DYNAMIC BASS, NIGHT, “TONE,”
and “DEC. MODE”) to on/off.
[On]: Enables all of the system’s sound effects.
The upper limit of sampling frequency is set to
48kHz.
[On]: Attenuates the input level. The output
level is changed.
[Off]: Normal input level.
[Off]: The sound effects are disabled. Select this
when you do not want to set the upper limit of
sampling frequency.
x [BD/DVD Audio Output]
x [Speaker Settings]
The system cannot output multi-channel sound
from both the HDMI OUT jack and system’s
speakers simultaneously. You can select the
output method.
To obtain the best possible surround sound, set
the speakers. For details, see “Setting the
x [Auto Calibration]
[Speaker only]: Outputs multi-channel sound
from the system’s speakers only.
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
[Speaker priority]: Outputs multi-channel sound
from the system’s speakers and 2-channel linear
PCM signals from the HDMI OUT jack.
[HDMI priority]: Outputs 2-channel stereo
sound from the system’s speakers, and enables
sound output from the HDMI OUT jack. Sound
format from the HDMI OUT jack depends on
the connected component.
Note
• When you set [BD/DVD Audio Output] to [HDMI
priority], a confirmation message appears on the TV
screen. Press C/c to select [OK] to complete the
setup.
• When you set [BD/DVD Audio Output] to [HDMI
priority], the SOUND MODE, DYNAMIC BASS,
NIGHT, “TONE,” and “DEC. MODE” functions are
disabled.
• When the System Audio Control function (page 65)
is activated, this setting may change automatically.
US
79
Download from Www.Somanuals.com. All Manuals Search And Download.
to [255] using C/X/x/c and the number
buttons.
[BD/DVD Viewing
Settings]
To cancel the Parental Control setting
Select [No Restrictions].
Note
You can make detailed settings for BD/DVD
• If you forget the password, reset the system (page 86)
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
unit.
playback.
x [BD/DVD Menu]
You can select the default menu language for
BD-ROMs or DVD VIDEOs.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
• Depending on the disc, you may be asked to change
the Parental Control level while playing the disc. In
this case, enter your password, then change the level.
• When [255] is selected in [Select Age Restriction],
the Parental Control setting is canceled.
Tip
x [Audio]
• You can change the password. See [Password]
You can select the default track language for
BD-ROMs or DVD VIDEOs.
When you select [Original], the language given
priority in the disc is selected.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
x [DVD Parental Control]
Playback of some DVD VIDEOs can be limited
according to a predetermined level such as the
age of the users. Scenes may be blocked or
replaced with different scenes.
1
2
3
Enter your four-digit password using
the number buttons.
x [Subtitle]
You can select the default subtitle language for
BD-ROMs or DVD VIDEOs.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
Press X/x to select [OK], then press
.
Press X/x to select a level, then press
.
The lower the value, the stricter the
limitation.
To cancel the Parental Control setting
x [BD Parental Control]
Select [No Restrictions].
Playback of some BD-ROMs can be limited
according to the age of the users. Scenes may be
blocked or replaced with different scenes.
Note
• If you forget the password, reset the system (page 86)
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
unit.
1
2
3
Enter your four-digit password using
the number buttons.
Press X/x to select [OK], then press
• Depending on the disc, you may be asked to change
the Parental Control level while playing the disc. In
this case, enter your password, then change the level.
.
Press X/x to select the age restriction,
then press
.
Tip
The lower the value, the stricter the
limitation.
• You can change the password. See [Password]
If you select [Select Age Restriction], you
can enter the age restriction level from [0]
US
80
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Enter a new password using the
number buttons.
x [Parental Control Region Code]
Playback of some BD-ROMs or DVD VIDEOs
can be limited according to the geographic area.
Scenes may be blocked or replaced with
different scenes.
Press X/x to select [OK], then press
.
x [Hybrid Disc Playback Layer]
You can select the layer priority when playing a
Hybrid Disc. To change the setting, turn the
system off and on again.
1
2
3
Enter your four-digit password using
the number buttons.
Press X/x to select [OK], then press
.
[BD]: Plays BD layer.
[DVD/CD]: Plays DVD or CD layer.
Press X/x to select the area restriction,
then press
.
When you select [Select Region Code], the
display for entering the region code
appears. Enter the code for the area
restriction by referring to “Parental Control/
x [BD Internet Connection]
You can set whether or not to allow Internet
connections from the contents of a BD (in
BDMV mode) being played. Network
connections and settings are required when
Note
• If you forget the password, reset the system (page 86)
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
unit.
[Allow]: Normally select this.
[Do not allow]: Prohibits Internet connection.
• Depending on the disc, you may be asked to change
the Parental Control level while playing the disc. In
this case, enter your password, then change the level.
Tip
• You can change the password. See [Password]
x [Password]
You can set or change the password for the
Parental Control function. A password allows
you to set a restriction on BD-ROM or DVD
VIDEO playback. If necessary, you can
differentiate the restriction levels for BD-ROMs
and DVD VIDEOs.
1
2
Enter your four-digit password using
the number buttons.
Press X/x to select [OK], then press
.
To change the password
1
2
After Step 1, enter your four-digit
password using the number buttons.
Press X/x to select [OK], then press
.
US
81
Download from Www.Somanuals.com. All Manuals Search And Download.
[Photo Settings]
[HDMI Settings]
You can make the photo-related settings.
You can make the HDMI settings.
x [Slideshow Speed]
x [Control for HDMI]
You can change the slideshow speed.
You can set the [Control for HDMI] function to
on/off. For details, see “Using the Control for
[Fast]: Photos change rapidly.
[Normal]: Photos change at normal speed.
[Slow]: Photos change slowly.
[On]: On. You can operate mutually between
components that are connected with an HDMI
cable.
[Off]: Off.
x [Volume Limit]
If you change the output method of the TV to the
system speaker on the TV menu or by pressing
THEATER, the System Audio Control
(page 65) is activated and loud sound may be
output depending on the volume level of the
system. You can prevent this by limiting the
maximum level of the volume.
[Level3]: Maximum volume level is set to 10.
[Level2]: Maximum volume level is set to 15.
[Level1]: Maximum volume level is set to 20.
[Off]: Off.
Note
• This function is available only when you connect the
unit and TV with an HDMI cable and [Control for
HDMI] is set to [On].
US
82
Download from Www.Somanuals.com. All Manuals Search And Download.
x [Software Update Notification]
[System Settings]
You can make the system-related settings.
You can get information on newer software
versions. The information appears on the TV
screen when you turn the system on. Network
connections and settings are required when
x [OSD]
You can select your language for the system on-
screen displays.
[On]: Sets the system to inform you of newer
[Off]: Off.
x [Standby Mode]
You can shorten the startup time when turning
the system on.
x [System Information]
You can display the system’s software version
information and the MAC address.
[Quick Start]: Shortens the startup time from
standby mode. You can operate the system
quickly after turning it on.
[Normal]: The default setting.
Note
• When [Standby Mode] is set to [Quick Start], power
consumption will be higher than when [Standby
Mode] is set to [Normal].
x [Auto Display]
You can display information when switching
audio modes or during playback.
[On]: Automatically displays information on the
screen when changing the viewing titles, picture
modes, audio signals, etc.
[Off]: Displays information only when you
press
DISPLAY.
x [Screen Saver]
The screen saver image appears when you do not
use the system for more than 15 minutes while
an on-screen display, such as the home menu, is
displayed on your TV screen. The screen saver
image helps prevent your display device from
becoming damaged (ghosting).
[On]: Turns on the screen saver function.
[Off]: Off.
US
83
Download from Www.Somanuals.com. All Manuals Search And Download.
3
If your ISP has a specific proxy server
setting, press X/x to select [Proxy
[Network Settings]
You can make detailed settings for Internet and
Settings], then press
.
The [Proxy Settings] display appears.
If the proxy server does not have a specific
setting, go to step 8.
network.
x [Internet Settings]
4
5
6
Press X/x to select [Use of Proxy
These items are necessary when you connect to
the Internet via a network cable. Enter the
respective (alphanumeric) values for your
broadband router or Wireless LAN router. The
items that need to be set may differ, depending
on the Internet service provider or the router. For
details, refer to the instruction manuals that have
been provided by your Internet service provider
or supplied with the router.
Server], then press
.
Press X/x to select [On], then press
.
Select [Proxy Server] and [Port], and
enter the settings.
To enter the proxy server, see “To enter
7
8
Press RETURN.
1
2
Press X/x to select [IP Address
Acquisition], then press
Press X/x to select [Network
.
Diagnostic], then press
.
Press X/x to select an item, then press
9
Press C/c to select [Start], then press
.
.
[Use DHCP]: Select this when DHCP
(Dynamic Host Configuration Protocol)
server settings are available from your
Internet service provider. The network
settings necessary for the system will be
assigned automatically.
10
Check that the message [Network
connections are correct.] appears.
The setup is finished. If the message does
not appear, follow the on-screen messages.
To enter characters
The display for entering characters appears
when you select [Proxy Server] in [Proxy
Settings].
If you set [DNS Server Auto Acquisition] to
[Off], set the following items:
– [DNS Server (Primary)]
– [DNS Server (Secondary)]
Proxy Server Entry
[Use Static IP Address]: Set the IP address
manually according to your network
environment.
Clear
Clear All
Set the following items:
Space 0
Cancel
Finish
– [IP Address]
Letter Type
Symbol
– [Subnet Mask]
– [Default Gateway]
– [DNS Server (Primary)]
– [DNS Server (Secondary)]
1
Press the number button repeatedly to
select a character.
Example:
Press the number 3 button once to enter [D].
Press the number 3 button three times to
enter [F].
Note
• When you set the [DNS Server (Primary)]/
[DNS Server (Secondary)] addresses manually,
enter the [DNS Server (Primary)] address.
Otherwise, the [Internet Settings] will be set
incorrectly.
2
3
Press c, and enter the next character.
Press YELLOW ([Finish]) to finish.
US
84
Download from Www.Somanuals.com. All Manuals Search And Download.
You can use the following buttons to enter
characters.
[Easy Setup]
You can recall the Easy Setup to make the basic
Buttons
Details
RED
[Letter Type]
Switches the keyboard between
alphabet and numbers.
settings.
1
2
Press C/c to select [Start], then press
GREEN
[A/a]
Switches the keyboard between
upper case and lower case.
.
BLUE
[Symbol]
Displays the keyboard for
symbols.
Follow the instructions for “Step 3:
from step 4.
YELLOW
[Finish]
The input is entered, and the
system returns to the previous
display.
CLEAR
Erases the character to the right
[Clear]/[Clear All] of the cursor.
To erase all displayed characters,
press and hold CLEAR for 2
seconds or more.
RETURN
[Cancel]
Returns to the previous display,
canceling the input.
C/X/x/c,
• Select an input function using
C/X/x/c, and press
.
• Enter characters as follows:
1Select a character selection
panel using C/X/x/c, and press
. 2Select a character using
C/c, and press
.
US
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting all the system
settings to the default
[Resetting]
Resetting the system settings
other than the settings related
to password
You can reset all the system settings to the
default settings.
1
2
Press
to select [Reset to Factory
Default Settings], then press
.
You can reset the system settings to their factory
default. Settings can be reset by function group.
All the settings within the group will be reset.
Press X/x to select [All Settings], then
press
.
The display asks for confirmation.
1
2
Press
to select [Reset to Factory
3
Press x and VOLUME – on the unit at
the same time for more than 5 seconds.
Default Settings], then press
.
Press X/x to select the settings you
want to reset to default, then press
All system settings are reset to the default
settings, and the system turns off.
.
You can reset the following settings:
– [Video Settings]
Note
• Settings for “Adjusting pictures for videos” (page 42)
are not reset.
– [Audio Settings]
– [BD/DVD Viewing Settings] (except for
the [BD Parental Control], [DVD
Parental Control], [Parental Control
Region Code], [Password] settings)
– [Photo Settings]
– [HDMI Settings]
– [System Settings]
– [Network Settings]
– [All Settings] (except for the [BD
Parental Control], [DVD Parental
Control], [Parental Control Region
Code], [Password] settings)
The display asks for confirmation.
Note
• When [All Settings] is selected, all system
settings other than the settings related to the
password are reset, and the system turns off.
• Settings for “Adjusting pictures for videos”
(page 42) are not reset.
3
Press C/c to select [Start], then press
.
To cancel, select [Cancel].
US
86
Download from Www.Somanuals.com. All Manuals Search And Download.
On operation
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the unit. Should
this occur, the system may not operate properly. In
this case, remove the disc and leave the system turned
on for about half an hour until the moisture
evaporates.
Additional Information
Precautions
On safety
• To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the system, or
place the system near water, such as near a bathtub or
shower room. Should any solid object or liquid fall
into the cabinet, unplug the system and have it
checked by qualified personnel before operating it
any further.
• When you move the system, take out any disc. If you
don’t, the disc may be damaged.
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
On adjusting volume
• Do not touch the AC power cord (mains lead) with
wet hands. Doing so may cause an electric shock.
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
On power sources
• Unplug the unit from the wall outlet (mains) if you do
not intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
On cleaning
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
On placement
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the system in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the system can overheat and malfunction.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On replacement of parts
• In the events that this system is repaired, repaired
parts may be collected for reuse or recycling
purposes.
• Do not place the system on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that may
block the ventilation slots.
• Do not install the system in a confined space, such as
a bookshelf or similar unit.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
• Do not install the system near heat sources such as
radiators, air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
• Do not install the system in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the system and discs away from components
with strong magnets, such as microwave ovens, or
large loudspeakers.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
• Do not place heavy objects on the system.
US
87
Download from Www.Somanuals.com. All Manuals Search And Download.
On moving the system
Before moving the system, make sure that there is no
disc inserted, and remove the AC power cord (mains
lead) from the wall outlet (mains).
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
This system can only playback a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
US
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your
nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
In the event of a problem with the S-AIR function, have a Sony dealer check the entire system together
(S-AIR main unit and sub unit).
Power
Symptom
Remedy
The power is not turned on.
• Check that the AC power cord (mains lead) is connected securely.
• Press "/1 after “STANDBY” disappears from the front panel display.
If “PROTECTOR” and “PUSH Press "/1 to turn off the system, and check the following items after
POWER” appear alternately in “STANDBY” disappears.
the front panel display.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If
the cause of the problem cannot be found even after checking all the above
items, consult your nearest Sony dealer.
Picture
Symptom
Remedy
There is no picture.
• The video connecting cords are not connected securely.
• The video connecting cords are damaged.
• The video input on the TV is not set so that you can view pictures from the
system.
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
• When playing a double-layer DVD, the video and audio may be momentarily
interrupted at the point where the layers switch.
No picture appears when the
• Press and hold N and Z on the unit for more than 5 seconds to reset the video
video output resolution selected output resolution to the lowest resolution.
in [Output Video Format] is
incorrect.
Video signals are not output
from the jacks, other than from
the HDMI OUT jack, when
connecting the HDMI OUT jack
and other video output jacks at
the same time.
dark/the bright area is too bright
or unnatural.
US
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The picture is not output
correctly.
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your system goes through your VCR to get to your
TV, the copy-protection signal applied to some BD/DVD programs could affect
picture quality. If you still experience problems even when you connect your
unit directly to your TV, try connecting your unit to the other input jacks.
Even though you set the aspect • The aspect ratio on the disc is fixed.
ratio in [TV Type] of [Video
Settings], the picture does not fill
the TV screen.
Color irregularity occurs on the • If the speakers are used with a CRT-based TV or projector, install the speakers
TV screen.
at least 1.0 ft (0.3 meters) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15
to 30 minutes.
• If howling occurs, reposition the speakers farther away from the TV set.
• Make sure that no magnetic object (magnetic latch on a TV stand, health care
device, toy, etc.) is placed near the speakers.
Sound
Symptom
Remedy
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON” is displayed in the front panel
display.
• The system is in pause mode. Press N to return to normal play mode.
• Fast forward or fast reverse is performed. Press N to return to normal play
mode.
• Slow forward or freeze frame is performed. Press N to return to normal play
mode.
No sound is output from the
HDMI OUT jack.
• The HDMI OUT jack is connected to a DVI (Digital Visual Interface) device
jacks do not accept audio signals.
• Try the following: 1 Turn the system off and on again. 2 Turn the connected
component off and on again. 3 Disconnect and then connect an HDMI cable
again.
• Set [BD/DVD Audio Output] to [HDMI priority] (page 79).
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components are connected correctly and securely.
There is no sound from the
subwoofer.
Severe hum or noise is heard.
• Check that the speakers and components are connected securely.
• Check that the connecting cords are away from a transformer or motor, and at
least 10 feet (3 meters) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The sound loses stereo effect
when you play a CD.
• Make sure the unit is connected properly.
US
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
hear when you are playing a
sound track of Dolby Digital,
DTS, or MPEG audio.
• Depending on the BD/DVD, the output signal may not be the entire 5.1 channel.
It may be monaural or stereo even if the sound track is recorded in Dolby
Digital or MPEG audio format.
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.
speaker only.
No sound is heard from the
center speaker.
• Depending on the source, the effect of the center speaker may be less
noticeable.
• A 2 channel source is being played.
No sound or only a very low-
level sound is heard from the
surround speakers.
• Depending on the source, the effect of the surround speakers may be less
noticeable.
• A 2 channel source is being played.
off.
The sound effects are disabled. • The effects of SOUND MODE, DYNAMIC BASS, NIGHT, “TONE,” and
Distortion occurs in the sound of • Reduce the input level for the connected component by setting [Attenuate - TV]
a connected component.
Operation
Symptom
Remedy
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna
in.
(aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic
tuning). Use direct tuning.
• No stations have been preset or the preset stations have been cleared (when
• Press DISPLAY so that the frequency appears in the front panel display.
Noise is heard on AM radio.
The remote does not function.
• There are obstacles between the remote and the unit.
• The distance between the remote and the unit is too far.
• The remote is not pointed at the remote sensor on the unit.
• The batteries in the remote are weak.
• When you cannot perform menu operations via the front panel display, press
HOME on the remote.
US
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The disc does not play.
• The disc is dirty.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• You are attempting to play a disc with a format that cannot be played back by
• The region code on the BD/DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
File names are not displayed
correctly.
• The system can only display ISO 8859-1-compliant character formats. Other
character formats may be displayed differently.
• Depending on the writing software used, the input characters may be displayed
differently.
A disc does not start playing
from the beginning.
• Resume Play has been selected.
Press OPTIONS and select [Play from beginning], then press
.
• The title or BD/DVD menu automatically appears on the TV screen.
• The BD/DVD features an auto playback function.
The system starts playing the
disc automatically.
Playback stops automatically.
• Some discs may contain an auto pause signal. While playing such a disc, the
system stops playback at the auto pause signal.
You cannot perform some
• Depending on the disc, you may not be able to perform some of the operations
functions such as stop or search. above. Refer to the operating instructions supplied with the disc.
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in
TV screen in the language you
want.
The language for the soundtrack/ • Try using the BD’s or DVD’s menu instead of the direct selection button on the
subtitle or angles cannot be
changed.
• Multi-lingual tracks/subtitles or multi-angles are not recorded on the BD or
DVD being played.
• The BD or DVD prohibits the changing of the language for the sound track/
subtitle or angles.
The disc tray does not open and • Try the following: 1 Press and hold VOLUME – and Z on the unit for more
you cannot remove the disc even than 5 seconds to open the disc tray. 2 Remove the disc. 3 Disconnect the AC
after you press Z.
power cord (mains lead) from the wall outlet (mains), then reconnect after
several minutes.
A disc cannot be ejected and
“LOCKED” appears in the front
panel display.
• Contact your Sony dealer or local authorized Sony service facility.
The system does not work
normally.
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then
reconnect after several minutes.
US
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The Control for HDMI function • When “HDMI” does not light up in the front panel display, check the HDMI
does not work.
• Make sure that the connected component is compatible with the [Control for
HDMI] function.
• Check that the AC power cord (mains lead) of the connected component is
connected securely.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power
cord (mains lead), or have a power failure, set [Control for HDMI] in [HDMI
Settings] to [Off], then set [Control for HDMI] in [HDMI Settings] to [On]
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
No sound is output from the
system and TV while using the
System Audio Control function.
• Make sure that the connected TV is compatible with the System Audio Control
function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
The external memory is not
recognized.
• Try the following: 1 Turn the system off. 2 Align the V mark of the EXT slot
with the V mark on the external memory, and insert the external memory
(USG1H only). 3 Turn the system on. 4 Check that the EXT indicator lights
up in the front panel display.
Bonus contents or other data that • Try the following: 1 Remove the disc. 2 Turn the system off. 3 Remove and
are contained in a BD-ROM
cannot be played.
the EXT indicator lights up in the front panel display. 6 Insert the BD-ROM
with BonusView/BD-Live.
A message indicating that the
local storage does not have
enough space appears on the
screen.
The unit does not work and
“CHILD LOCK” appears in the
front panel display when you
press any button on the unit.
The system menu does not work. • Press HOME on the remote.
US
93
Download from Www.Somanuals.com. All Manuals Search And Download.
The S-AIR function
Symptom
Remedy
S-AIR connection is not
established (sound transmission
is not established), e.g., the
indicator of the S-AIR sub unit
does the following:
• Turns off.
• If you use another S-AIR main unit, place it more than 26 1/4 feet (8 meters)
away from the unit.
• You performed pairing the unit and another S-AIR sub unit. Perform pairing of
• The unit is paired to another S-AIR sub unit. To cancel pairing, reset the ID of
• Flashes.
• Turns red.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Stop using another wireless product.
• The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is
connected and turn on the S-AIR sub unit.
No sound is heard from the
S-AIR sub unit.
• If you use another S-AIR main unit, place it more than 26 1/4 feet (8 meters)
away from the unit.
• Install the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Stop using another wireless product.
• Change the ID settings of the S-AIR main unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then turn on them.
There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 26 1/4 feet (8 meters)
away from the unit.
• Install the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Stop using another wireless product.
• Change the ID settings of the S-AIR main unit and S-AIR sub unit.
US
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Self-diagnosis Function
When the self-diagnosis function is activated to
prevent the system from malfunctioning, an
error code appears in the front panel display, or
just
appears without any messages on the
entire screen. In these cases, check the
following.
When an error code appears in
the front panel display
Error code
Corrective action
Exxxx
Contact your nearest Sony dealer or
local authorized Sony service
facility and give the error code.
SYSTEM ERR Turn off the system and disconnect
the AC power cord (mains lead)
from the wall outlet (mains), then
reconnect and turn the system on. If
the system does not work normally,
consult your nearest Sony dealer or
local authorized Sony service
facility.
UPDATE NG
When just
appears without
any messages on the entire
screen
Contact your nearest Sony dealer or local
authorized Sony service facility.
US
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable Discs
Type
Disc logo
Characteristics
Icon
Blu-ray Disc
BD-ROMs and BD-REs/BD-Rs in
BDMV and BDAV mode, including
8 cm discs (single layer) and DL
discs
DVD VIDEO
Discs such as movies that can be
purchased or rented
DVD/DATA DVD
DVD+RWs/DVD+Rs in +VR mode
or DVD-RWs/DVD-Rs in video and
VR mode, including 8 cm discs
(single layer) and DVD+R DL/
DVD-R DL discs
DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs containing JPEG* image
files
AVCHD
CD
Discs recorded in AVCHD format**
TM
Music CDs or CD-Rs/CD-RWs in
music CD format
DATA CD
–
CD-Rs/CD-RWs containing JPEG
image files
* JPEG format conforming to UDF (Universal Disk Format).
**Some AVCHD format discs may not play, depending on the recording condition. The AVCHD format disc will
not play if it has not been correctly finalized.
Notes about BD-ROM compatibility
Since the Blu-ray Disc specifications are new and evolving, some discs may not be playable depending
on the disc type and the version.
The audio output differs depending on the source, connected output jack, and selected audio settings.
Discs that cannot be played
• BDs with cartridge
• DVD-RAMs
• HD DVDs
• DVD Audio discs
• PHOTO CDs
• Data part of CD-Extras
• VCDs/Super VCDs
• HD layer on Super Audio CDs
US
96
Download from Www.Somanuals.com. All Manuals Search And Download.
• A disc recorded in a color system other than NTSC, such as PAL (this system conforms to the NTSC
color system).
Note on playback operations of a BD/DVD
Some playback operations of a BD/DVD may be intentionally set by software producers. Since this
system plays a BD/DVD according to the disc contents the software producers designed, some
playback features may not be available. Refer to the instructions supplied with the BD/DVD.
Region code (BD-ROM/DVD VIDEO only)
Your system has a region code printed on the rear of the unit and will only play a BD-ROM/DVD
VIDEO (playback only) labeled with identical region codes. This system is used to protect copyrights.
ALL
DVD VIDEO labeled
will also play on this system.
If you try to play any other DVD VIDEO, the message [Playback prohibited by region code.] will
appear on the TV screen. Depending on the BD-ROM/DVD VIDEO, no region code may be indicated
even though playing the BD-ROM/DVD VIDEO is prohibited by area restrictions.
Notes about BD-REs/BD-Rs, DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or
CD-Rs/CD-RWs
Some BD-REs/BD-Rs, DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/CD-RWs cannot be
played on this system due to the recording quality or physical condition of the disc, or the
characteristics of the recording device and authoring software. The BD-Rs recorded on a PC cannot be
played if postscripts are recordable.
A CD or DVD disc will not play if it has not been correctly finalized. For more information, refer to
the operating instructions supplied with the recording device. Note that some playback functions may
not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view
the disc using normal playback.
Notes on discs
This product is designed to playback discs that conform to the Compact Disc (CD) standard.
DualDiscs and some of the music discs encoded with copyright protection technologies do not conform
to the Compact Disc (CD) standard, therefore, these discs may not be playable by this product.
Note about double-layer DVDs
The playback pictures and sound may be momentarily interrupted when the layers switch.
Note about 8 cm BD-REs/8 cm BD-Rs
Some 8 cm BD-REs/8 cm BD-Rs cannot be played on this system.
Note about BD-REs/BD-Rs
This system supports Ver. 2.1 BD-RE and Ver. 1.1 and 1.2 BD-R including organic pigment type BD-
R (LTH type).
US
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Audio Formats
Audio formats supported by this system are as follows.
Format
LPCM 2ch
LPCM 5.1ch,
LPCM 7.1ch
Dolby Digital Dolby
TrueHD,
DTS
DTS-ES
Discrete 6.1,
DTS-ES
Matrix 6.1,
DTS96/24
DTS-HD
High
Resolution
Audio
DTS-HD
Master
Audio
Function
Dolby Digital
Plus
“BD/DVD”
a
a
a
a
a
a
a
a
a*
a
a
“SAT/CABLE”
“TV”
–
–
–
–
–
(DIGITAL IN)
a: Supported format.
–: Unsupported format.
* BD only.
Note
• The table above is valid only when you set [BD Audio Setting] to [Direct] (page 78) and [Sound Effect] to [Off]
(page 79). If another setting is used, depending on the audio format, sound may be decoded to a suitable format
automatically.
US
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Output Resolution
Output resolution differs depending on the [Output Video Format] setting in [Video Settings]
When [Output Video Format] is set to
[HDMI]
When [Output Video Format] is set to
[Component Video]
Resolution
setting
COMPONENT
COMPONENT
VIDEO OUT
jack
HDMI OUT
VIDEO OUT
jack
HDMI OUT
VIDEO OUT
jack
VIDEO OUT
jacks
jack
jack
480i
480i
480i
480i
480i
480i
480p
720p
1080i
1080p
480i
480i
480i
480p
480i
480p
480p
720p
1080i
1080p
480i
480i
480i
720p*
720p*
480i
480i
480i
1080i*
1080i*
no picture
no picture
unselectable
unselectable
unselectable
* Protected contents on DVDs are output at 480p resolution.
When [Output Video Format] is set to [Video]
480i video signals are output from the VIDEO OUT or COMPONENT VIDEO OUT jack, and 480p
video signals are output from the HDMI OUT jack.
About the video output resolution of the DIGITAL MEDIA PORT adapter
480i video signals are output from the VIDEO OUT jack regardless of the resolution setting, and video
signals are not output from the HDMI OUT and COMPONENT VIDEO OUT jacks when playing
contents via the DIGITAL MEDIA PORT adapter.
US
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround mode (reference) RMS output power
Front L/Front R/Center/
Surround L/Surround R*:
143 watts (per channel at 3
ohms, 1 kHz, 10% THD)
Subwoofer*: 285 watts (at
1.5 ohms, 80 Hz, 10%
Specifications
Amplifier Section
(BDV-T10/BDV-T11)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
THD)
(FTC Output Power)
for the US model
*
Depending on the decoding mode settings and the
source, there may be no sound output.
Front L/Front R:
With 3 ohms loads, both
channels driven, from 180
- 20,000 Hz; rated 56 watts
per channel minimum
Inputs (Analog)
TV (AUDIO IN)
Sensitivity: 450/250 mV
Impedance: 50 kilohms
Sensitivity: 450/250 mV
Impedance: 50 kilohms
RMS power, with no more
than 0.7% total harmonic
distortion from 250 milli
watts to rated output.
AUDIO (AUDIO IN)
Inputs (Digital)
TV (OPTICAL)
Impedance: -
Surround mode (reference) RMS output power
Front L/Front R/Center/
Surround L/Surround R*:
133 watts (per channel at 3
ohms, 1 kHz, 10% THD)
Subwoofer*: 135 watts (at
1.5 ohms, 80 Hz, 10%
SAT/CABLE (COAXIAL)
Impedance: 75 ohms
Video Section
Outputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
THD)
*
Depending on the decoding mode settings and the
source, there may be no sound output.
HDMI OUT: Type A (19
pin)
BD/DVD/CD System
Signal format system
Amplifier Section
(BDV-E300)
NTSC
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC Output Power)
Tuner Section
System
PLL quartz-locked digital
synthesizer
for the US model
Front L/Front R:
FM tuner section
Tuning range
With 3 ohms loads, both
channels driven, from 180
- 20,000 Hz; rated 56 watts
per channel minimum
87.5 MHz - 108.0 MHz
(100 kHz step)
FM wire antenna (aerial)
Antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
RMS power, with no more
than 0.7% total harmonic
distortion from 250 milli
watts to rated output.
Intermediate frequency
AM tuner section
Tuning range
10.7 MHz
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
AM loop antenna (aerial)
450 kHz
U.S. models:
Surround mode (reference) RMS output power
Front L/Front R/Center/
Surround L/Surround R*:
143 watts (per channel at 3
ohms, 1 kHz, 10% THD)
Subwoofer*: 285 watts (at
1.5 ohms, 80 Hz, 10%
THD)
Antenna (aerial)
Intermediate frequency
Speakers (BDV-T10/BDV-T11)
Front (SS-TSB95)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
102 mm × 163 mm × 77
mm (4 1/8 in × 6 1/2 in ×
3 1/8 in) (w/h/d)
Other models:
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
US
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Mass (approx.)
0.52 kg (1 lb 3 oz)
Surround (SS-TSB92)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
105 mm × 225 mm × 85
mm (4 1/4 in × 8 7/8 in ×
3 3/8 in) (w/h/d)
Center (SS-CTB92)
Speaker system
Full range, Magnetically
Shielded
30 mm × 60 mm (1 3/16 in ×
2 3/8 in) cone type
3 ohms
380 mm × 50 mm × 64 mm
(15 in × 2 in × 2 5/8 in)
(w/h/d)
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
0.6 kg (1 lb 6 oz)
Subwoofer (SS-WSB91)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Subwoofer Bass reflex
180 mm (7 1/8 in) cone type
1.5 ohms
225 mm × 395 mm × 325
mm (8 7/8 in × 15 5/8 in ×
12 7/8 in) (w/h/d)
Mass (approx.)
0.38 kg (14 oz)
Surround (SS-TSB95)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
102 mm × 163 mm × 77
mm (4 1/8 in × 6 1/2 in ×
3 1/8 in) (w/h/d)
Mass (approx.)
6.2 kg (13 lb 11 oz)
General
Power requirements
Power consumption
120 V AC, 60 Hz
On: 160 W
Mass (approx.)
0.52 kg (1 lb 3 oz)
Standby: 0.3 W (at the
Power Saving mode)
Subwoofer (SS-WSB92)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Subwoofer Bass reflex
Output voltage/current
160 mm (6 3/8 in) cone type
1.5 ohms
(DIGITAL MEDIA PORT)
DC 5 V/700 mA
220 mm × 395 mm × 325
mm (8 3/4 in × 15 5/8 in ×
12 7/8 in) (w/h/d)
LAN (100)
EXT
100BASE-TX Terminal
External memory slot (For
connecting the external
memory)
Mass (approx.)
5.6 kg (12 lb 6 oz)
Speakers (BDV-E300)
DC output: 5 V 500 mA
Max
430 mm × 93 mm × 400
mm (17 in × 3 3/4 in ×
15 3/4 in) (w/h/d) incl.
projecting parts
Front (SS-TSB93)
Speaker system
Dimensions (approx.)
Mass (approx.)
2-Way 2-Driver, Bass
reflex
Speaker unit
Tweeter: 20 mm (13/16 in)
cone type
5.4 kg (11 lb 15 oz)
Woofer: 65 mm (2 5/8 in)
cone type
3 ohms
105 mm × 225 mm × 85
mm (4 1/4 in × 8 7/8 in ×
3 3/8 in) (w/h/d)
0.7 kg (1 lb 9 oz)
Design and specifications are subject to change
without notice.
Rated impedance
Dimensions (approx.)
• Standby power consumption 0.3 W.
• Halogenated flame retardants are not used in the
certain printed wiring boards.
Mass (approx.)
Center (SS-CTB91)
Speaker system
• Over 85% power efficiency of amplifier block is
achieved with the full digital amplifier, S-Master.
Full range, Magnetically
Shielded
Speaker unit
30 mm × 60 mm (1 3/16 in ×
2 3/8 in) cone type
3 ohms
Rated impedance
Dimensions (approx.)
380 mm × 51 mm × 68 mm
(15 in × 2 1/8 in × 2 3/4 in)
(w/h/d)
Mass (approx.)
0.4 kg (15 oz)
US
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control/Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
US
102
Download from Www.Somanuals.com. All Manuals Search And Download.
password or any other breach of security related to the Service, Site,
and/or Software.
Terms and Conditions of
Use and End User
License Agreement
The Sony Blu-ray Disc player (“Product”) and associated software
(“Software”) are provided and maintained by Sony Electronics Inc.
and its affiliates (“Sony”). Sony also provides and maintains
associated service (the “Service”), including any subsite accessible
through the Service’s Internet homepage (the “Site”). The Software
includes software embedded in the Product; stored on any media,
bundled with the Product or otherwise provided by Sony;
downloaded from the Site or otherwise made accessible or provided
by Sony; any such media and any printed or “on-line” or electronic
documentation associated with the Product and all updates and
upgrades thereto.
Sony’s Privacy Policy is posted on the Site and at
http://products.sel.sony.com/SEL/legal/privacy.html, the
terms of which are incorporated herein, and applies to your use of the
Account, Product, Service, Site, and Software.
4. Automatic Update
The Software contains a functionality by which it is updated
automatically when the Product is connected to a server belonging to
Sony or to a third party designated by Sony. When you specify your
intention not to use this automatic update functionality, or when the
setting asking whether you wish to update automatically is activated
and you decline to execute updates, it is assumed that you agree that
the security functionality improvements, error corrections, other
functional updates or any other changes offered by Sony through
such updates would not be made to the Software and that your
current and further use of the Software may be affected thereby.
When the automatic update functionality described in the previous
paragraph is activated, it is assumed that you agree (a) that the
Software will be automatically updated as necessary to improve
security functionality, to correct errors, to improve update
functionality, or for other purposes, and (b) that this updating of the
Software may be accompanied by the augmenting, modifying, or
removing of functionality of the Software.
WHEN YOU ACCESS, BROWSE, OR USE THE SERVICE,
PRODUCT, SOFTWARE, AND/OR SITE, YOU ACCEPT,
WITHOUT LIMITATION OR QUALIFICATION, THE TERMS
AND CONDITIONS SET FORTH HEREIN, SONY’S PRIVACY
POLICY POSTED ON THE SITE, AND ANY ADDITIONAL
TERMS AND CONDITIONS OF USE SET FORTH IN ANY
PORTION OF THE SERVICE AND SITE (COLLECTIVELY THE
“AGREEMENT”). IF YOU DO NOT AGREE WITH THE TERMS
AND CONDITIONS OF THIS AGREEMENT, SONY DOES NOT
GRANT THE LIMITED RIGHTS HEREIN, AND PLEASE DO
NOT USE THE SERVICE, PRODUCT, SOFTWARE, AND/OR
SITE.
5. Additional Terms Governing Product Software
You may use the Software solely in conjunction with the Product that
accompanied the Software. The Software is licensed, not sold. In
addition to the terms set forth in other portions of this Agreement, the
Software is subject to the following:
Use of Software. You may use the Software in conjunction with the
Product for personal use.
Limitation on Reverse Engineering, Decompilation and
Disassembly. You may not modify, reverse engineer, decompile, or
disassemble the Software in whole or in part.
Separation of Components.The Software is licensed as a single
product. Its component parts may not be separated for use on more
than one device unless expressly authorized by Sony.
Data Files. The Software may create data files automatically for use
with the Software. Any such data files will be deemed as part of the
Software.
1. Ownership
The Software and all materials on the Service and/or Site, including
but not limited to images, software and text (the “Content”) are
protected by copyright under U.S. copyright law, international
conventions, and other copyright laws. You cannot use the Software,
Service, Product, Content, and Site except as specified herein. There
may be proprietary logos, service marks, and trademarks found on
this Service or Site. By making them available on the Service and/or
Site, Sony is not granting you any license to utilize those proprietary
logos, service marks, or trademarks. Any unauthorized use of the
Service, Site, Content or Software may violate copyright laws,
trademark laws, the laws of privacy and publicity, and civil and
criminal statutes. All title and copyright in and to the Software or
materials on the Service/Site and any copies of the Software, are
owned by Sony, its licensors, or suppliers. All rights not specifically
granted under this Agreement are reserved by Sony, its licensors, and
suppliers.
Rental. You may not rent or lease the Software.
Software Transfer. You may permanently transfer all of your rights
under this Agreement only as part of a sale or transfer of Software
accompanying the sale or transfer of your Product, provided you
retain no copies, transfer all of the Software (including all copies,
component parts, the media and printed materials, all versions and
any upgrades of the Software and this Agreement), and the recipient
agrees to the terms of this Agreement.
Dependent Software. The software, network services or other
products other than Software upon which the Software’s
performance depends on might be interrupted or discontinued at the
discretion of the suppliers (software suppliers, service providers or
Sony).
High Risk Activities. The Software is not fault-tolerant and is not
designed, manufactured or intended for use or resale as on-line
control equipment in hazardous environments requiring fail-safe
performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life
support machines, or weapons systems, in which the failure of the
Software could lead to death, personal injury, or severe physical or
environmental damage (“High Risk Activities”). Sony and its
suppliers specifically disclaim any express or implied warranty of
fitness for High Risk Activities.
U.S. Government Restricted Rights. The Software is provided with
RESTRICTED RIGHTS. Use, duplication, or disclosure by the
United States Government is subject to restriction as set forth in
subparagraph (c) (1) and (2) of the Commercial Computer Software-
Restricted Rights at 48 CFR 52.227-19, as applicable. Manufacturer
is Sony Electronics Inc., 16530 Via Esprillo, San Diego, CA 92127.
2. Your Rights & Limited License
The Service, Site, Software, Content, and Product are only for your
personal use. You are responsible for all your activities hereunder,
including all legal liability incurred from your use of the Service or
others who use the Service via your Product or Account (as defined
below). You may use the Service, Site, Software, Content and
Product for lawful purposes only. You may not distribute, exchange,
modify, sell, or transmit anything you may copy from the Service or
Site, including but not limited to any text, images, audio, and video,
for any business, commercial, or public purpose. As long as you
comply with the terms of this Agreement, Sony grants you a non-
exclusive, non-transferable, limited right to enter, display, and use
the Service, Site, and Software as set forth in this Agreement. You
agree not to interrupt/disrupt or attempt to interrupt/disrupt the
operation of this Service, Site or Software in any way.
3. User Account & Privacy
As part of your usage of the Product, Service, Site, and/or Software,
Sony may require that you establish a user account (“Account”) for
which you must provide Sony true, accurate, current, and complete
information about yourself and maintain/promptly update such
information. You are responsible for maintaining the confidentiality
of any and all of your passwords associated with the Account. You
agree to notify Sony immediately of any unauthorized use of your
US
103
Download from Www.Somanuals.com. All Manuals Search And Download.
GNU General Public, Lesser General Public, & Other Licenses.
Notwithstanding terms in this Agreement, certain portions of the
Software are governed by the GNU Lesser General Public License,
Version 2.1 (LGPL), GNU General Public License Version 2 (GPL),
and other open source code licenses (“Open Source Licenses”),
copies of which are attached hereto and incorporated herein. For
such portions of the Software, to the extent there is any conflict
between this Agreement and the Open Source Licenses, the Open
Source Licenses shall govern as applicable.
Certain Source Code Availability. Sony is making available the
source code of certain portions of the SOFTWARE per the GPL/
LGPL LICENSES. Please see http://www.sony.com/linux for
access to and instructions on obtaining such source code.
9. Indemnification
You agree to indemnify, defend, and hold Sony and all of its agents,
directors, employees, information providers, licensors and licensees,
affiliates, content providers, officers, and parent (collectively,
“Indemnified Parties”), harmless from and against any and all
liability and costs (including, without limitation, attorneys’ fees and
costs), incurred by the Indemnified Parties in connection with any
claim arising out of (i) any breach or alleged breach by you of this
Agreement in any manner, (ii) any information you submit to Sony
hereunder, (iii) any breach or alleged breach by you of a third party’s
rights or (iv) any damage caused by or alleged to have been caused
by you to the Service. You will cooperate as fully as reasonably
required in Indemnified Party(s) defense of any claim. Sony and/or
Indemnified Parties reserve the right, at its own expense, to assume
the exclusive defense and control of any matter otherwise subject to
indemnification by you and you shall not in any event settle any
matter without the written consent of Sony and/or Indemnified
Parties.
6. Changes to Service
Sony reserves the right to discontinue one, some, or all of the
features of the Service you receive at any time at its discretion. Sony
may, at its discretion and from time to time change, add or remove
features and functionality, upgrade or modify the Service, Site and/
or Software without notice. You may, at Sony’s discretion, receive
messages regarding these changes and new features/functionality.
Any new text, content, file, data, product, services, information,
software, software tool or other feature provided by Sony (through
the network or by CD-ROM or other means) (including, but not
limited to, any update to Software provided to you automatically
pursuant to Section 4 of this Agreement) will be subject to this
Agreement; provided that, if separate terms and conditions
applicable to such feature are provided to you, such terms and
conditions shall apply to such feature in priority to this Agreement.
10. DISCLAIMER OF WARRANTIES AND DAMAGES;
LIMITATION OF LIABILITY
YOU UNDERSTAND THAT USAGE OF THE PRODUCT AND
SERVICE REQUIRES INTERNET SERVICE PROVIDED BY
YOU, FOR WHICH YOU ARE SOLELY RESPONSIBLE.
OPERATION OF THE PRODUCT AND/OR SERVICE MAY BE
LIMITED OR RESTRICTED DEPENDING UPON THE
CAPABILITIES OR TECHNICAL LIMITATIONS OF YOUR
INTERNET SERVICE.
YOUR USE OF THE SOFTWARE, SERVICE, PRODUCT,
CONTENT AND/OR SITE IS AT YOUR OWN RISK. THE
SOFTWARE, SERVICE, CONTENT AND SITE ARE PROVIDED
“AS IS” AND, TO THE FULLEST EXTENT PERMISSIBLE BY
LAW, SONY MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHATSOEVER (1) FOR THE
ACCURACY, MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT
ASSOCIATED WITH THE SERVICE, SITE, AND/OR
SOFTWARE; (2) THAT THE SERVER(S) THAT MAKES THE
SERVICE, SOFTWARE, AND/OR SITE AVAILABLE ARE
FREE OF VIRUSES OR OTHER COMPONENTS THAT MAY
INFECT, HARM, OR CAUSE DAMAGE TO YOUR
COMPUTER, TELEVISION, OTHER EQUIPMENT, OR ANY
OTHER PROPERTY. FURTHERMORE, SONY DOES NOT
WARRANT OR MAKE ANY REPRESENTATIONS
REGARDING THE USE OR THE RESULTS OF THE USE OF
THE SOFTWARE, SERVICE, AND/OR SITE IN TERMS OF ITS
CORRECTNESS, ACCURACY, RELIABILITY, OR
OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR
ADVICE GIVEN BY SONY OR A SONY AUTHORIZED
REPRESENTATIVE SHALL CREATE A WARRANTY OR IN
ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
SHOULD THE SOFTWARE, SERVICE, AND/OR SITE PROVE
DEFECTIVE YOU (AND NOT SONY OR A SONY
AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
7. Confidentiality
You shall maintain the confidentiality of any information with
regard to the Product and Documentation that is provided under this
Agreement and is not publicly known. You agree not to disclose
such information to any third party without the prior written consent.
8. Sony’s Right to Terminate or Modify Terms or
Conditions of this Agreement
Sony may add to, change, or remove any part, term, or condition of
this Agreement at any time, without prior notice. Any changes to this
Agreement or any terms posted on the Service and/or Site apply as
soon as they are posted. By continuing to use the Service, Product,
Software and/or Site after any changes are posted, you are indicating
your acceptance of those changes. SONY MAY ADD, CHANGE,
DISCONTINUE, REMOVE, OR SUSPEND ANY OTHER
CONTENT POSTED ON THE SERVICE AND/OR SITE,
INCLUDING FEATURES AND SPECIFICATIONS OF
PRODUCTS DESCRIBED OR DEPICTED ON THE SERVICE
AND/OR SITE, TEMPORARILY OR PERMANENTLY, AT ANY
TIME, WITHOUT NOTICE AND WITHOUT LIABILITY.
WITHOUT PREJUDICE TO ANY OTHER RIGHTS, SONY MAY
SUSPEND OR TERMINATE THIS AGREEMENT
IMMEDIATELY UPON NOTICE IF YOU FAIL TO COMPLY
WITH THE TERMS AND CONDITIONS OF THIS
AGREEMENT. Upon termination, you shall destroy the Software
within fourteen (14) days after the date of such termination, and upon
Sony’s request, provide Sony with the certification of such
destruction. Sony may take any legal and technical remedies to
prevent the violation of and/or to enforce this Agreement, including
without limitation, immediate termination of your access to the
Service if we believe in our discretion you are violating this
Agreement.
UNDER NO CIRCUMSTANCES, INCLUDING BUT NOT
LIMITED TO SONY’S NEGLIGENCE OR ISSUES RELATED
TO THIRD PARTY CONTENT PROVIDERS, SHALL SONY BE
LIABLE FOR ANY CONSEQUENTIAL, DIRECT,
INCIDENTAL, INDIRECT, PUNITIVE, OR SPECIAL
DAMAGES RELATED TO (A) THE USE OF, (B) THE
INABILITY TO USE, OR (C) ERRORS OR OMISSIONS IN THE
SOFTWARE, SERVICE, PRODUCT, AND/OR SITE, EVEN IF
SONY OR AN AUTHORIZED REPRESENTATIVE THEREOF
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR
INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT
SHALL SONY’S TOTAL LIABILITY TO YOU FOR ALL
DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER
IN CONTRACT OR TORT, INCLUDING, BUT NOT LIMITED
TO, NEGLIGENCE OR OTHERWISE) EXCEED $100.00.
US
104
Download from Www.Somanuals.com. All Manuals Search And Download.
11. General Provisions
This Agreement, the limited warranty accompanying the Product,
plus any additional terms posted on the Service or Site, together
constitute the entire agreement between Sony and you with respect
to your use of the Product, Service, Site, Content, and Software. Any
notice by Sony hereunder may be made by letter, email, or posting
on the Service or Site. Any cause of action you may have with
respect to your use of this Site must be commenced within one (1)
year after the claim or cause of action arises. If for any reason a court
of competent jurisdiction finds any provision of this Agreement, or
portion thereof, to be unenforceable, that provision shall be enforced
to the maximum extent permissible so as to affect the intent of this
Agreement, and the remaining terms and conditions of the
Agreement shall continue in full force and effect. This Agreement
shall be governed by and construed in accordance with the laws of
the State of Delaware, United States of America, without reference
to its conflicts of law rules. You agree to submit to the personal and
exclusive jurisdiction of federal or state courts in Delaware.
Software License
Information
Required public statement & License for
GPL/LGPL licensed software used in this
product
This product contains software that is subject to the following GNU
General Public License (“GPL”) or GNU Lesser General Public
License (“LGPL”). These establish that customers have the right to
acquire, modify, and redistribute the source code of said software in
accordance with the terms of the GPL or the LGPL.
Package List
linux-kernel.tar.gz
pump
lrzsz
busybox
gcc
glibc
netbase
dosfstools
lzo
mkcramfs
hostname
scfs
The source code for the above-listed software is available on the
Web.
To download, please access the following URL:
http://www.sony.net/Products/Linux
Please note that Sony cannot answer or respond to any inquiries
regarding the content of this source code.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
Preamble
The Licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change
free software--to make sure the software is free for all its users. This
General Public License applies to most of the Free Software
Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software
is covered by the GNU Lesser General Public License instead.) You
can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code or
can get it if you want it, that you can change the software or use
pieces of it in new free programs; and that you know you can do these
things.
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that you
have. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know
their rights.
US
105
Download from Www.Somanuals.com. All Manuals Search And Download.
We protect your rights with two steps: (1) copyright the software,
and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the Program,
and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote
it.
Also, for each author’s protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original,
so that any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making the
program proprietary. To prevent this, we have made it clear that any
patent must be licensed for everyone’s free use or not licensed at all.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise
the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on
a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
The precise terms and conditions for copying, distribution and
modification follow.
GNU GENERAL PUBLIC LICENSE TERMS AND
CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one of
the following:
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The
“Program”, below, refers to any such program or work, and a
“work based on the Program” means either the Program or any
derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or with
modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
a) Accompany it with the complete corresponding machine-
readable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily
used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to
be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the
offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution
and only if you received the program in object code or
executable form with such an offer, in accord with Subsection
b above.)
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of
running the Program is not restricted, and the output from the
Program is covered only if its contents constitute a work based on the
Program (independent of having been made by running the
Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to the absence
of any warranty; and give any other recipients of the Program a
copy of this License along with the Program.
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating
system on which the executable runs, unless that component itself
accompanies the executable.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a
fee.
2. You may modify your copy or copies of the Program or any
portion of it, thus forming a work based on the Program, and copy
and distribute such modifications or work under the terms of
Section 1 above, provided that you also meet all of these
conditions:
If distribution of executable or object code is made by offering
access to copy from a designated place, then offering equivalent
access to copy the source code from the same place counts as
distribution of the source code, even though third parties are not
compelled to copy the source along with the object code.
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that
in whole or in part contains or is derived from the Program or
any part thereof, to be licensed as a whole at no charge to all
third parties under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started
running for such interactive use in the most ordinary way, to
print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling
the user how to view a copy of this License. (Exception: if the
Program itself is interactive but does not normally print such
an announcement, your work based on the Program is not
required to print an announcement.)
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program
is void, and will automatically terminate your rights under this
License. However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify
or distribute the Program or its derivative works. These actions
are prohibited by law if you do not accept this License.
Therefore, by modifying or distributing the Program (or any
work based on the Program), you indicate your acceptance of this
License to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on it.
US
106
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the
original licensor to copy, distribute or modify the Program
subject to these terms and conditions. You may not impose any
further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance
by third parties to this License.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/
OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this
License. If you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the
Program at all. For example, if a patent license would not permit
royalty-free redistribution of the Program by all those who
receive copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be to refrain
entirely from distribution of the Program.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER
If any portion of this section is held invalid or unenforceable under
any particular circumstance, the balance of the section is intended to
apply and the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any
such claims; this section has the sole purpose of protecting the
integrity of the free software distribution system, which is
implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot
impose that choice.
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it
free software which everyone can redistribute and change under
these terms.
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in
certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the Program under this
License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this
License.
To do so, attach the following notices to the program. It is safest to
attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found.
<one line to give the program’s name and an idea of what it does.>
Copyright (C) <year> <name of author>
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such
new versions will be similar in spirit to the present version, but
may differ in detail to address new problems or concerns.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published
by the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
Each version is given a distinguishing version number. If the
Program specifies a version number of this License which applies to
it and “any later version”, you have the option of following the terms
and conditions either of that version or of any later version published
by the Free Software Foundation. If the Program does not specify a
version number of this License, you may choose any version ever
published by the Free Software Foundation.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-
1307, USA.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the
author to ask for permission. For software which is copyrighted
by the Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free
status of all derivatives of our free software and of promoting the
sharing and reuse of software generally.
Also add information on how to contact you by electronic and paper
mail.
If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for
details type ‘show w’. This is free software, and you are welcome to
redistribute it under certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than ‘show w’ and
‘show c’; they could even be mouse-clicks or menu items--whatever
suits your program.
US
107
Download from Www.Somanuals.com. All Manuals Search And Download.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the program,
if necessary. Here is a sample; alter the names:
Most GNU software, including some libraries, is covered by the
ordinary GNU General Public License. This license, the GNU Lesser
General Public License, applies to certain designated libraries, and is
quite different from the ordinary General Public License. We use this
license for certain libraries in order to permit linking those libraries
into non-free programs.
Yoyodyne, Inc., hereby disclaims all copyright interest in the
program ‘Gnomovision’ (which makes passes at compilers) written
by James Hacker.
When a program is linked with a library, whether statically or using
a shared library, the combination of the two is legally speaking a
combined work, a derivative of the original library. The ordinary
General Public License therefore permits such linking only if the
entire combination fits its criteria of freedom. The Lesser General
Public License permits more lax criteria for linking other code with
the library.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your
program into proprietary programs. If your program is a subroutine
library, you may consider it more useful to permit linking proprietary
applications with the library. If this is what you want to do, use the
GNU Lesser General Public License instead of this License.
We call this license the “Lesser” General Public License because it
does Less to protect the user’s freedom than the ordinary General
Public License. It also provides other free software developers Less
of an advantage over competing non-free programs. These
disadvantages are the reason we use the ordinary General Public
License for many libraries. However, the Lesser license provides
advantages in certain special circumstances.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs
must be allowed to use the library. A more frequent case is that a free
library does the same job as widely used non-free libraries. In this
case, there is little to gain by limiting the free library to free software
only, so we use the Lesser General Public License.
[This is the first released version of the Lesser GPL. It also counts
as the successor of the GNU Library Public License, version 2, hence
the version number 2.1.]
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General Public
Licenses are intended to guarantee your freedom to share and change
free software--to make sure the software is free for all its users.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body of
free software. For example, permission to use the GNU C Library in
non-free programs enables many more people to use the whole GNU
operating system, as well as its variant, the GNU/Linux operating
system.
This license, the Lesser General Public License, applies to some
specially designated software packages--typically libraries--of the
Free Software Foundation and other authors who decide to use it.
You can use it too, but we suggest you first think carefully about
whether this license or the ordinary General Public License is the
better strategy to use in any particular case, based on the
explanations below.
Although the Lesser General Public License is Less protective of the
users’ freedom, it does ensure that the user of a program that is linked
with the Library has the freedom and the wherewithal to run that
program using a modified version of the Library.
When we speak of free software, we are referring to freedom of use,
not price. Our General Public Licenses are designed to make sure
that you have the freedom to distribute copies of free software (and
charge for this service if you wish); that you receive source code or
can get it if you want it; that you can change the software and use
pieces of it in new free programs; and that you are informed that you
can do these things.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between a
“work based on the library” and a “work that uses the library”. The
former contains code derived from the library, whereas the latter
must be combined with the library in order to run.
GNU GENERAL PUBLIC LICENSE TERMS AND
CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any software library or other
program which contains a notice placed by the copyright holder
or other authorized party saying it may be distributed under the
terms of this Lesser General Public License (also called “this
License”). Each licensee is addressed as “you”.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender these
rights. These restrictions translate to certain responsibilities for you
if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or
for a fee, you must give the recipients all the rights that we gave you.
You must make sure that they, too, receive or can get the source
code. If you link other code with the library, you must provide
complete object files to the recipients, so that they can relink them
with the library after making changes to the library and recompiling
it. And you must show them these terms so they know their rights.
A “library” means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work
which has been distributed under these terms. A “work based on the
Library” means either the Library or any derivative work under
copyright law: that is to say, a work containing the Library or a
portion of it, either verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter, translation is
included without limitation in the term “modification”.)
We protect your rights with a two-step method: (1) we copyright the
library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there
is no warranty for the free library. Also, if the library is modified by
someone else and passed on, the recipients should know that what
they have is not the original version, so that the original author’s
reputation will not be affected by problems that might be introduced
by others.
“Source code” for a work means the preferred form of the work for
making modifications to it. For a library, complete source code
means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the library.
Finally, software patents pose a constant threat to the existence of
any free program. We wish to make sure that a company cannot
effectively restrict the users of a free program by obtaining a
restrictive license from a patent holder. Therefore, we insist that any
patent license obtained for a version of the library must be consistent
with the full freedom of use specified in this license.
US
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of
running a program using the Library is not restricted, and output
from such a program is covered only if its contents constitute a work
based on the Library (independent of the use of the Library in a tool
for writing it). Whether that is true depends on what the Library does
and what the program that uses the Library does.
4. You may copy and distribute the Library (or a portion or
derivative of it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided that you
accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for
software interchange.
1. You may copy and distribute verbatim copies of the Library’s
complete source code as you receive it, in any medium, provided
that you conspicuously and appropriately publish on each copy
an appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to the absence
of any warranty; and distribute a copy of this License along with
the Library.
If distribution of object code is made by offering access to copy from
a designated place, then offering equivalent access to copy the source
code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the
source along with the object code.
5. A program that contains no derivative of any portion of the
Library, but is designed to work with the Library by being
compiled or linked with it, is called a “work that uses the
Library”. Such a work, in isolation, is not a derivative work of the
Library, and therefore falls outside the scope of this License.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a
fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and copy
and distribute such modifications or work under the terms of
Section 1 above, provided that you also meet all of these
conditions:
However, linking a “work that uses the Library” with the Library
creates an executable that is a derivative of the Library (because it
contains portions of the Library), rather than a “work that uses the
library”. The executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices
stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a
table of data to be supplied by an application program that
uses the facility, other than as an argument passed when the
facility is invoked, then you must make a good faith effort to
ensure that, in the event an application does not supply such
function or table, the facility still operates, and performs
whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has
a purpose that is entirely well-defined independent of the
application. Therefore, Subsection 2d requires that any
application-supplied function or table used by this function must
be optional: if the application does not supply it, the square root
function must still compute square roots.)
When a “work that uses the Library” uses material from a header file
that is part of the Library, the object code for the work may be a
derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The threshold
for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure
layouts and assessors, and small macros and small inline functions
(ten lines or less in length), then the use of the object file is
unrestricted, regardless of whether it is legally a derivative work.
(Executables containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may
distribute the object code for the work under the terms of Section 6.
Any executables containing that work also fall under Section 6,
whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or
link a “work that uses the Library” with the Library to produce a
work containing portions of the Library, and distribute that work
under terms of your choice, provided that the terms permit
modification of the work for the customer’s own use and reverse
engineering for debugging such modifications.
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
Library, and can be reasonably considered independent and
separate works in themselves, then this License, and its terms, do
not apply to those sections when you distribute them as separate
works. But when you distribute the same sections as part of a
whole which is a work based on the Library, the distribution of
the whole must be on the terms of this License, whose
You must give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are covered by
this License. You must supply a copy of this License. If the work
during execution displays copyright notices, you must include the
copyright notice for the Library among them, as well as a reference
directing the user to the copy of this License. Also, you must do one
of these things:
permissions for other licensees extend to the entire whole, and
thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise
the right to control the distribution of derivative or collective works
based on the Library.
a) Accompany the work with the complete corresponding
machine-readable source code for the Library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work is
an executable linked with the Library, with the complete
machine-readable “work that uses the Library”, as object
code and/or source code, so that the user can modify the
Library and then relink to produce a modified executable
containing the modified Library. (It is understood that the
user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the
application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the
Library. A suitable mechanism is one that (1) uses at run time
a copy of the library already present on the user’s computer
system, rather than copying library functions into the
executable, and (2) will operate properly with a modified
version of the library, if the user installs one, as long as the
modified version is interface-compatible with the version that
the work was made with.
In addition, mere aggregation of another work not based on the
Library with the Library (or with a work based on the Library) on a
volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General
Public License instead of this License to a given copy of the
Library. To do this, you must alter all the notices that refer to this
License, so that they refer to the ordinary GNU General Public
License, version 2, instead of to this License. (If a newer version
than version 2 of the ordinary GNU General Public License has
appeared, then you can specify that version instead if you wish.)
Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that
copy, so the ordinary GNU General Public License applies to all
subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the
Library into a program that is not a library.
US
109
Download from Www.Somanuals.com. All Manuals Search And Download.
c) Accompany the work with a written offer, valid for at least
three years, to give the same user the materials specified in
Subsection 6a, above, for a charge no more than the cost of
performing this distribution.
If any portion of this section is held invalid or unenforceable under
any particular circumstance, the balance of the section is intended to
apply, and the section as a whole is intended to apply in other
circumstances.
d) If distribution of the work is made by offering access to copy
from a designated place, offer equivalent access to copy the
above specified materials from the same place.
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any
such claims; this section has the sole purpose of protecting the
integrity of the free software distribution system which is
implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot
impose that choice.
For an executable, the required form of the “work that uses the
Library” must include any data and utility programs needed for
reproducing the executable from it. However, as a special exception,
the materials to be distributed need not include anything that is
normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain
countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Library under this
License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this
License.
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally
accompany the operating system. Such a contradiction means you
cannot use both them and the Library together in an executable that
you distribute.
7. You may place library facilities that are a work based on the
Library side-by-side in a single library together with other library
facilities not covered by this License, and distribute such a
combined library, provided that the separate distribution of the
work based on the Library and of the other library facilities is
otherwise permitted, and provided that you do these two things:
13. The Free Software Foundation may publish revised and/or new
versions of the Lesser General Public License from time to time.
Such new versions will be similar in spirit to the present version,
but may differ in detail to address new problems or concerns.
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms of
the Sections above.
b) Give prominent notice with the combined library of the fact
that part of it is a work based on the Library, and explaining
where to find the accompanying uncombined form of the
same work.
Each version is given a distinguishing version number. If the Library
specifies a version number of this License which applies to it and
“any later version”, you have the option of following the terms and
conditions either of that version or of any later version published by
the Free Software Foundation. If the Library does not specify a
license version number, you may choose any version ever published
by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free
programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software
which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions
for this. Our decision will be guided by the two goals of
8. You may not copy, modify, sublicense, link with, or distribute
the Library except as expressly provided under this License. Any
attempt otherwise to copy, modify, sublicense, link with, or
distribute the Library is void, and will automatically terminate
your rights under this License. However, parties who have
received copies, or rights, from you under this License will not
have their licenses terminated so long as such parties remain in
full compliance.
preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
NO WARRANTY
9. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify
or distribute the Library or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License to do so,
and all its terms and conditions for copying, distributing or
modifying the Library or works based on it.
15. BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE LIBRARY IS
WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
10. Each time you redistribute the Library (or any work based on the
Library), the recipient automatically receives a license from the
original licensor to copy, distribute, link with or modify the
Library subject to these terms and conditions. You may not
impose any further restrictions on the recipients’ exercise of the
rights granted herein. You are not responsible for enforcing
compliance by third parties with this License.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE LIBRARY (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE
11. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this
License. If you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the
Library at all. For example, if a patent license would not permit
royalty-free redistribution of the Library by all those who receive
copies directly or indirectly through you, then the only way you
could satisfy both it and this License would be to refrain entirely
from distribution of the Library.
LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
US
110
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names without
prior written permission of the OpenSSL Project.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free software
that everyone can redistribute and change. You can do so by
permitting redistribution under these terms (or, alternatively, under
the terms of the ordinary General Public License).
6. Redistributions of any form whatsoever must retain the following
acknowledgment:
“This product includes software developed by the OpenSSL
Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
“AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
To apply these terms, attach the following notices to the library. It is
safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should
have at least the “copyright” line and a pointer to where the full
notice is found.
<one line to give the library’s name and an idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it
under the terms of the GNU Lesser General Public License as
published by the Free Software Foundation; either version 2.1 of the
License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE. See the GNU Lesser General Public License for more
details.
This product includes cryptographic software written by Eric Young
Tim Hudson ([email protected]).
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-
1307 USA
Original SSLeay License
Also add information on how to contact you by electronic and paper
mail.
Original SSLeay
Copyright (C) 1995-1998 Eric Young ([email protected])
All rights reserved.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the library,
if necessary. Here is a sample; alter the names:
This package is an SSL implementation written by Eric Young
The implementation was written so as to conform with Netscapes
SSL.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library
‘Frob’ (a library for tweaking knobs) written by James Random
Hacker.
This library is free for commercial and non-commercial use as long
as the following conditions are aheared to. The following conditions
apply to all code found in this distribution, be it the RC4, RSA, lhash,
DES, etc., code; not just the SSL code. The SSL documentation
included with this distribution is covered by the same copyright
terms except that the holder is Tim Hudson ([email protected]).
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
Required statements for OpenSSL project
used in this product
This product contains OpenSSL (including the library Original
SSLeay), which Sony uses under license with the copyright holder.
In compliance with a request by the copyright holder of said
software, Sony conveys the following notice and asks that you read
it.
Copyright remains Eric Young’s, and as such any Copyright notices
in the code are not to be removed.
If this package is used in a product, Eric Young should be given
attribution as the author of the parts of the library used.
This can be in the form of a textual message at program startup or in
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
Package name: sony-target-grel-openssl-0.9.8g-020201.src.rpm
OpenSSL
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.
1. Redistributions of source code must retain the copyright notice,
this list of conditions and the following disclaimer.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided
with the distribution.
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided
with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
“This product includes cryptographic software written by Eric
Young ([email protected])”
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment:
“This product includes software developed by the OpenSSL
The word ‘cryptographic’ can be left out if the rouines from the
library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you must
include an acknowledgement:
“This product includes software written by Tim Hudson
Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not
be used to endorse or promote products derived from this
software without prior written permission. For written
permission, please contact [email protected].
US
111
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES,
The following notices are required to satisfy the license terms of the
software that we have mentioned in this document:
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
This product includes software developed by Adam Glass.
This product includes software developed by Bill Paul.
This product includes software developed by Charles M. Hannum.
This product includes software developed by Christian E. Hopps.
This product includes software developed by Christopher G.
Demetriou.
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This product includes software developed by Christopher G.
Demetriou for the NetBSD Project.
This product includes software developed by Christos Zoulas.
This product includes software developed by Gardner Buchanan.
This product includes software developed by Gordon W. Ross
This product includes software developed by Jonathan Stone for the
NetBSD Project.
This product includes software developed by Manuel Bouyer.
This product includes software developed by Rolf Grossmann.
This product includes software developed by TooLs GmbH.
This product includes software developed by the NetBSD
Foundation, Inc. and its contributors.
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e. this code
cannot simply be copied and put under another distribution licence
[including the GNU Public Licence.]
This product includes software developed by the University of
California, Berkeley and its contributors.
This product includes software developed by the University of
California, Lawrence Berkeley Laboratory and its contributors.
This product includes software developed by the University of
California, Lawrence Berkeley Laboratory.
FreeType
The FreeType Project is copyright (C) 1996-2000 by David Turner,
Robert Wilhelm, and Werner Lemberg. All rights reserved except as
specified below.
THE FREETYPE PROJECT IS PROVIDED ‘AS IS’ WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES
CAUSED BY THE USE OR THE INABILITY TO USE, OF THE
FREETYPE PROJECT.
This product includes software developed for the NetBSD Project by
Wasabi Systems, Inc.
This product includes software developed for the NetBSD Project by
Matthias Drochner..
Notice about JPEG
Parts of this product utilize the research results of the Independent
JPEG Group.
Package name sony-target-grel-libjpeg-6b-020201.src.rpm.
Notice about NetBSD Software
In plain English:
BSD License
1. We don’t promise that this software works. (But if you find any
bugs, please let us know!)
Copyright (c) 1994-2004 The NetBSD Foundation, Inc. All rights
reserved.
2. You can use this software for whatever you want. You don’t
have to pay us.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
3. You may not pretend that you wrote this software. If you use it
in a program, you must acknowledge somewhere in your
documentation that you’ve used the IJG code.
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
In legalese:
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided
with the distribution.
The authors make NO WARRANTY or representation, either
express or implied, with respect to this software, its quality,
accuracy, merchantability, or fitness for a particular purpose. This
software is provided “AS IS”, and you, its user assume the entire risk
as to its quality and accuracy.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
This product includes software developed by the NetBSD
Foundation, Inc. and its contributors.
This software is copyright (c) 1991-1998, Thomas G. Lane.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this
software (or portions thereof) for any purpose, without fee, subject
to these conditions:
4. Neither the name of The NetBSD Foundation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
(1) If any part of the source code for this software is distributed, then
this README file must be included, with this copyright and no-
warranty notice unaltered; and any additions, deletions, or changes
to the original files must be clearly indicated in accompanying
documentation.
(2) If only executable code is distributed, then the accompanying
documentation must state that “this software is based in part on the
work of the Independent JPEG Group”.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION)
(3) Permission for use of this software is granted only if the user
accepts full responsibility for any undesirable consequences; the
authors accept NO LIABILITY for damages of any kind.
These conditions apply to any software derived from or based on the
IJG code, not just to the unmodified library. If you use our work, you
ought to acknowledge us.
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
US
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Permission is NOT granted for the use of any IJG author’s name or
company name in advertising or publicity relating to this software or
products derived from it. This software may be referred to only as
“the Independent JPEG Group’s software”.
About MPEG-4 AVC and VC-1
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT
PORTFOLIO LICENSE AND VC-1 PATENT PORTFOLIO
LICENSE FOR THE PERSONAL AND NON-COMMERCIAL
USE OF A CONSUMER TO DECODE VIDEO IN COMPLIANCE
WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR THE
VC-1 STANDARD ("VC-1 VIDEO") THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM
A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO
AND/OR VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
We specifically permit and encourage the use of this software as the
basis of commercial products, provided that all warranty or liability
claims are assumed by the product vendor.
Notice about PuTTY Software
This product contains some code of the application PuTTY.
Source package: putty-0.58.tar.gz
License text: http://www.chiark.greenend.org.uk/~sgtatham/putty/
licence.html
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
PuTTY is copyright 1997-2006 Simon Tatham.
The curl license
Portions copyright Robert de Bath, Joris van Rantwijk, Delian
Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong, Nicolas
Barry, Justin Bradford, Ben Harris, Malcolm Smith, Ahmad Khalifa,
Markus Kuhn, and CORE SDI S.A.
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2009, Daniel Stenberg, <[email protected]>.
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
“Software”), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject
to the following conditions:
Permission to use, copy, modify, and distribute this software for any
purpose with or without fee is hereby granted, provided that the
above copyright notice and this permission notice appear in all
copies.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY
RIGHTS. IN NO EVENT SHALL THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN
ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
The above copyright notice and this permission notice shall be
included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
SIMON TATHAM BE LIABLE FOR ANY CLAIM, DAMAGES
OR OTHER LIABILITY, WHETHER IN AN ACTION OF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder
shall not be used in advertising or otherwise to promote the sale, use
or other dealings in this Software without prior written authorization
of the copyright holder.
Notice about fdlibm Software
@(#)fdlibm.h 1.5 95/01/18
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Notice about expat
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center
Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003 Expat
maintainers.
Developed at SunSoft, a Sun Microsystems, Inc. business.
Permission to use, copy, modify, and distribute this software is freely
granted,provided that this notice is preserved.
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
“Software”), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject
to the following conditions:
Notice about Root Certificates
In addition, the Runtimes and Runtime Components may contain one
or more root certificates (herein referred to as “Root Certificates”).
You may not modify the Root Certificates.
Notice about Nano-XML
Copyright (C) 2000-2002 Marc De Scheemaecker, All Rights
Reserved.
The above copyright notice and this permission notice shall be
included in all copies or substantial portions of the Software.
This software is provided ‘as-is’, without any express or implied
warranty. In no event will the authors be held liable for any damages
arising from the use of this software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Permission is granted to anyone to use this software for any purpose,
including commercial applications, and to alter it and redistribute it
freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must
not claim that you wrote the original software. If you use this
software in a product, an acknowledgment in the product
documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and
must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source
distribution.
US
113
Download from Www.Somanuals.com. All Manuals Search And Download.
BD-ROM
BD-ROMs (Blu-ray Disc Read-Only Memory)
are commercially produced discs and are
available in the same capacities as the BD
below. Other than conventional movie and video
contents, these discs have enhanced features
such as interactive content, menu operations
using pop-up menus, selection of subtitle
display, and slideshow. Although a BD-ROM
may contain any form of data, most BD-ROM
discs will contain movies in High Definition
format, for playback on Blu-ray Disc/DVD
players.
Glossary
AVCHD
The AVCHD format is a high-definition digital
video camera format used to record SD
(standard definition) or HD (high definition)
signals of either the 1080i specification* or the
720p specification** on DVDs, using efficient
data compression coding technology. The
MPEG-4 AVC/H.264 format is adopted to
compress video data, and the Dolby Digital or
Linear PCM system is used to compress audio
data. The MPEG-4 AVC/H.264 format is
capable of compressing images at higher
efficiency than that of the conventional image
compression format. The MPEG-4 AVC/H.264
format enables a high definition (HD) video
signal shot on a digital video camera recorder to
be recorded on DVD discs in the same way as it
would be for a standard definition (SD)
television signal.
Blu-ray Disc (BD)
A disc format developed for recording/playing
high-definition (HD) video (for HDTV, etc.),
and for storing large amounts of data. A single
layer Blu-ray Disc holds up to 25 GB, and a
dual-layer Blu-ray Disc holds up to 50 GB of
data.
DCS (Digital Cinema Sound)
In collaboration with Sony Pictures
* A high definition specification that utilizes 1080
effective scanning lines and the interlace format.
**A high definition specification that utilizes 720
effective scanning lines and the progressive format.
Entertainment, Sony measured the sound
environment of their studios and integrated the
data of the measurement with Sony DSP (Digital
Signal Processor) technology to develop
“Digital Cinema Sound.” “Digital Cinema
Sound” simulates in a home theater an ideal
movie theater sound environment based on the
preference of the movie director.
BD-J application
The BD-ROM format supports Java for
interactive functions.
“BD-J” offers content providers almost
unlimited functionality when creating
interactive BD-ROM titles.
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjusts
the speaker settings to your listening
BD-R
BD-R (Blu-ray Disc Recordable) is a
recordable, write-once Blu-ray Disc, available
in the same capacities as the BD below. Since
contents can be recorded and cannot be
overwritten, a BD-R can be used to archive
valuable data or storing and distributing video
material.
environment in a short period of time.
Dolby Digital
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
BD-RE
BD-RE (Blu-ray Disc Rewritable) is a
recordable and rewritable Blu-ray Disc,
available in the same capacities as the BD
below. The re-recordable feature makes
extensive editing and time-shifting applications
possible.
US
114
Download from Www.Somanuals.com. All Manuals Search And Download.
DTS
since all the signals are processed digitally, less
signal degradation occurs.
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
comprises of stereo rear channel and there is
discrete subwoofer channel in this format. DTS
provides the same 5.1 discrete channels of high
quality digital audio. The good channel
separation is realized due to the all channel data
being recorded discretely and processed in
digitally.
Dolby Digital Plus
Developed as an extension to Dolby Digital, the
audio coding technology supports 7.1 multi-
channel surround sound.
Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
DTS-HD High Resolution Audio
Developed as an extension to DTS Digital
Surround format. It supports a maximum
sampling frequency of 96 kHz, and 7.1 multi-
channel surround.
DTS-HD High Resolution Audio has a
maximum transmission rate of 6 Mbps, with
lossy compression (Lossy).
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
DTS-HD Master Audio
x Music mode
DTS-HD Master Audio has a maximum
transmission rate of 24.5 Mbps, and uses
lossless compression (Lossless), and DTS-HD
Master Audio corresponds to a maximum
sampling frequency of 192 kHz, and maximum
of 7.1ch.
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
HDMI (High-Definition Multimedia
Interface)
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Content Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
Dolby TrueHD
Dolby TrueHD is a lossless coding technology
that supports up to 8 channels of multi-channel
surround sound for the next generation optical
discs. The reproduced sound is true to the
original source bit-for-bit.
Interlace format
(Interlaced scanning)
The Interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice -
alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
LTH (Low to High)
LTH is a recording system that supports organic
pigment type BD-R.
US
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Control
range of ISM band (Industrial, Scientific, and
Medical band), such as wireless LANs and
Bluetooth applications.
A function of the BD/DVD to limit playback of
the disc by the age of the users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
x.v.Color
x.v.Color is a familiar term for the xvYCC
standard proposed by Sony.
xvYCC is an international standard for Color
space in video.
PhotoTV HD
This standard can express a wider color range
than the currently used broadcast standard.
“PhotoTV HD” allows for a highly-detailed
pictures, and photo-like expression of subtle
textures and colors. By connecting Sony
“PhotoTV HD” compatible devices using an
HDMI cable, whole new world of photos can be
enjoyed in breathtaking Full HD quality. For
instance, the delicate texture of the human skin,
flowers, sand and waves can now be displayed
on a large screen in beautiful photo-like quality.
24p True Cinema
Movies shot with a film camera consist of 24
frames per second.
Since conventional televisions (both CRT and
flat panels) display frames either at 1/60 or 1/50
second intervals, the 24 frames do not appear at
an even pace.
When connected to a TV with 24p capabilities,
the player displays each frame at 1/24 second
intervals — the same interval originally shot
with the film camera, thus faithfully reproducing
the original cinema image.
Pop-up menu
An enhanced menu operation available on BD-
ROMs. The pop-up menu appears when POP
UP/MENU is pressed during playback, and can
be operated while playback is in progress.
Progressive format
(sequential scanning)
In contrast to the Interlace format, the
progressive format can reproduce 50 - 60 frames
per second by reproducing all scanning lines
(525 lines for the NTSC system). The overall
picture quality increases and still images, text
and horizontal lines appear sharper. This format
is compatible with the 525 or 625 progressive
format.
S-AIR
(Sony Audio Interactive Radio
frequency)
Recent times have seen the rapid spread of BD/
DVD media, Digital Broadcasting, and other
high-quality media.
To ensure that the subtle nuances of these high-
quality media are transmitted with no
deterioration, Sony has developed a technology
called “S-AIR” for the radio transmission of
digital audio signals with no compression, and
has incorporated this technology into the EZW-
RT10/EZW-RT10A/EZW-T100.
This technology transfers digital audio signals
with no compression using the 2.4 GHz band
US
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|