LCD Digital Colour TV
Operating Instructions
KDL-52EX1
KDL-46EX1
KDL-40EX1
© 2008 Sony Corporation
4-115-568-11(1)
Download from Www.Somanuals.com. All Manuals Search And Download.
2. TV wireless system can only be used in the following countries:
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, The Netherlands, Norway, Poland, Portugal, Slovak
Republic, Romania, Slovenia, Spain, Sweden, Switzerland, Turkey,
and The United Kingdom.
NOTICE FOR CUSTOMERS
IN THE UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug supplied need to be replaced with the
same rating of fuse approved by ASTA or BSI to BS 1362 (i.e.,
When using the TV wireless system, channels 36 to 48 (5.15-
5.25GHz) are selectable for indoor use only.
marked with
or
) must be used.
When an alternative type of plug is used it should be fitted with the
same rating of fuse, otherwise the circuit should be protected by a
13 AMP FUSE at the distribution board.
Trademark information
s
s
is a registered trademark of the DVB Project
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby Laboratories.
If the plug supplied with this equipment has a detachable fuse cover,
be sure to attach the fuse cover after you change the fuse. Never use
the plug without the fuse cover. If you should lose the fuse cover,
please contact your nearest Sony service station.
s
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
s
s
“BRAVIA” and
Corporation.
“XMB” and “xross media bar” are the trademarks of Sony
Corporation and Sony Computer Entertainment Inc.
are trademarks of Sony
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace
the fuse.
Please refer to the illustration that actually equipped with the
product.
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and
retain it for future reference.
The manufacturer of this product is Sony Corporation, 1-7-1
Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized
Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
Notice for Digital TV function
s
Any functions related to Digital TV (
) will only work in
countries or areas where DVB-T (MPEG-2 and H.264/MPEG-4
AVC) digital terrestrial signals are broadcast or where you have
access to a compatible DVB-C (MPEG-2 and H.264/MPEG-4
AVC) cable service. Please confirm with your local dealer if
you can receive a DVB-T signal where you live or ask your
cable provider if their DVB-C cable service is suitable for
integrated operation with this TV.
s
s
The cable provider may charge an additional fee for such a
service and you may be required to agree to their terms and
conditions of business.
Although this TV set follows DVB-T and DVB-C
specifications, compatibility with future DVB-T digital
terrestrial and DVB-C digital cable broadcasts cannot be
guaranteed.
s
s
Some Digital TV functions may not be available in some
countries/regions and DVB-C cable may not operate correctly
with all providers.
For more information about DVB-C functionality please see
our cable support site:
Notice for Wireless Signal
1. Hereby, Sony, declares that this unit is in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC.
To obtain the declaration of conformity (DoC) for R&TTE
Directive, please access the following URL address.
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Information.......................................................................................................................... 12
Precautions..................................................................................................................................... 14
Remote and Unit Controls/Indicators........................................................................................... 15
Navigating through Media Receiver Home Menu (XMB™)......................................................... 29
Navigating through Monitor Home Menu..................................................................................... 38
: for digital channels only
Before operating the TV, please read the “Safety information” section of this manual.
Retain this manual for future reference.
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up Guide
1: Checking the unit and
accessories
2: Connecting an aerial/Set
Top Box/recorder (e.g. DVD
recorder) to the media
receiver
Monitor (1)
Connecting a Set Top Box/recorder (e.g.
DVD recorder) with SCART
Media receiver (1)
Mains lead for monitor (1)
Mains lead for mains adaptor (1)
Mains adaptor for media receiver (1)
Mains lead holder (1)
Media receiver
Scart lead
Screws (PSW 4×8) (2)
Remote RMF-ED001W (1)
Size AA batteries (R6 type) (2)
IR Blaster (Y-cable) (2)
Set Top Box/recorder (e.g. DVD recorder)
Stand for media receiver (1)
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Set Top Box/recorder (e.g.
DVD recorder) with HDMI
3: Preventing the monitor
from toppling over
IN
Media receiver
HDMI cable
Set Top Box/recorder (e.g. DVD recorder)
~
• You can also connect equipment to the HDMI
input on the left side of the monitor.
1
2
Install a wood screw (4 mm in diameter,
not supplied) in the monitor stand.
Install a machine screw (M6 x 12-15, not
supplied) into the screw hole of the
monitor.
3
Tie the wood screw and the machine
screw with a strong cord.
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Connecting the mains
lead
5: Performing the initial set-
up
~
Inserting batteries into the remote
• Make sure to secure the mains lead.
• To ensure compliance with current EMC
legislation, ensure the following conditions are
met.
Push and lift the cover to open.
• Fix the mains lead holder (supplied) after
checking the mains lead is in the groove of the
mains lead holder (supplied) to avoid scratching
the mains lead.
1
~
• Observe the correct polarity when inserting
batteries.
• Do not use different types of batteries together or
mix old and new batteries.
AC
IN
• Dispose of batteries in an environmentally
friendly way. Certain regions may regulate the
disposal of batteries. Please consult your local
authority.
Monitor
• Handle the remote with care. Do not drop or step
on it, or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat
source, a place subject to direct sunlight, or a
damp room.
to mains socket
2
3
Screws (supplied)
Establishing the wireless
communication between the unit
~
• Keep about 30 cm to 20 m distance between the
monitor and media receiver when installing.
• Keep clear the area between the monitor and
media receiver. Otherwise the picture may
deteriorate.
Mains lead holder
(supplied)
• Rearrange the installation position of the monitor
and media receiver in case of fuzzy picture.
• Do not place either unit on a metallic rack.
• Do not use two units or more at the same time in
an area of radio interference.
18V
IN
C
D
1
Press 1 to turn on the unit power.
POWER button
Media receiver
Media receiver
to mains
socket
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
~
POWER button
• If the remote does not work, press F/f/G/g/ on
language.
2
Select “OK” then press
.
Monitor
2
Check the LINK indicator on the media
receiver.
Next, the Media Receiver Initial Set-up will start.
Please make sure the Media Receiver is on.
If wireless communication between the
media receiver and monitor is established,
this indicator lights up.
OK
LINK indicator
3
Press F/f to select the country in which
you will operate the unit, then press
.
LINK
Country
Select country
-
LINK
United Kingdom
Ireland
Nederland
België/Belgique
Luxembourg
France
Performing the initial set-up
Italia
TV
If the country in which you want to use
the unit does not appear in the list, select
“-” instead of a country.
HDMI 1
HDMI 2
AV1
HDMI 3
AV2
EXT
COMPO-
MONITOR
HDMI
NENT
4
Press F/f to select the location type in
which you will operate the unit, then press
SYNC MENU
THEATRE
.
DIGITAL/
ANALOG
AUDIO
~
• Select “Home” for the best monitor settings
to use the monitor in the home.
Location
1-10
Select location
Home
Shop
When you switch on the unit for the first
time, the Language menu appears on the
screen.
1
Press F/f/G/g to select the language
displayed on the menu screens, then press
5
Select “OK” then press
.
Auto Tuning
.
Language
Do you want to start Auto Tuning?
English
Español
Català
ББлгарски
Suomi
Nederlands
Français
Italiano
Português
Polski
Dansk
OK
Cancel
Svenska
Norsk
Deutsch
Česky
Magyar
Русский
Slovenčina
Română
Türkçe
GB
(Continued)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press F/f to select “Antenna” or “Cable”,
then press
~
.
• When a digital broadcast channel cannot be
received, or when selecting a country in which
there are no digital broadcasts in step 3, the time
must be set after performing step 7.
If you select “Cable”, the screen for
selecting the scan type appears. See “To
The unit starts searching for all available
digital channels, followed by all available
analogue channels. This may take some
time, so do not press any buttons on the
unit or remote while proceeding.
If a message appears for you to confirm
the aerial connection
No digital or analogue channels were
found. Check all the aerial/cable
connection and then press to start auto-
tuning again.
To tune the unit for Cable connection
1
2
Press
Press F/f to select “Quick Scan” or “Full
Scan”, then press
.
.
“Quick Scan” : channels are tuned
according to the cable operator
information within the broadcast signal.
Recommended setting for “Frequency”,
“Network ID” and “Symbol Rate” is
“Auto.”
This option is recommended for fast
tuning when supported by your cable
operator.
If the “Quick Scan” does not tune, please
use the “Full Scan” method below.
“Full Scan” : All available channels are
tuned and stored. This procedure may take
some time.
This option is recommended when “Quick
Scan” is not supported by your cable
provider.
7
8
When the “Programme Sorting” menu
appears on the screen, follow the steps of
If you do not change the order in which
the analogue channels are stored on the
unit, press
RETURN to go to step 8.
Quick Start
For further information about supported
cable providers, refer to support web site:
DVBC/
Do you want to enable Quick Start?
TV turns on more quickly but standby power
consumption is increased.
Yes
No
3
Press f to select “Start”, then press
.
The unit starts searching for channels. Do
not press any buttons on the unit or
remote.
9
Control for HDMI
~
• Some cable providers do not support “Quick
Scan.” If no channels are detected using “Quick
Scan”, perform “Full Scan.”
Do you want to enable control for compatible
HDMI devices?
Choosing "Yes" will increase
standby power consumption.
Yes
No
10 Press
.
The unit has now tuned in all the available
channels.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press F/f to select “IR Blaster Set-up”,
then press
The “IR Blaster Set-up” screen appears.
.
6: Operating optional
equipment using the remote
IR Blaster Set-up
Connecting IR Blaster to the optional
equipment
Inputs
Type
Make
Code
AV1
AV2
-
-
-
-
-
-
Turn the power of the media receiver off
before connecting the IR Blaster.
Attach the IR Blaster near the remote sensor
(IR) of the equipment.
HDMI 1
HDMI 2
HDMI 3
Component
Blu-ray Disc
Sony
1
-
-
-
-
-
-
-
-
-
5
Press F/f to select “Inputs” to register the
remote, then select the following items:
Media receiver
IR BLASTER
Type: Connected equipment category.
Make: Maker of the equipment.
Code: IR code.
Test: Tests the power of the equipment
currently being set. Make sure the power
of the equipment turns on and off.
If the equipment is not working, or
some of the functions do not work
IR
Blaster
Enter the correct code or its alternatives (if
available) shown in the list in step 5. Note that
the list may not include codes for all models of
all brands.
Optional equipment
~
• Only Sony equipment is guaranteed to properly
operate.
Performing the IR Blaster Set-up
By setting “IR Blaster Set-up”, this remote can
control most Sony Blu-ray Disc players, DVD
players, DVD recorders, and AV receivers, or
those of other manufacturers. Follow the steps
below to programme the remote.
1
2
Press HOME on the remote.
Press F/f to select “Settings”, then press
.
3
Press F/f to select “Media Receiver Set-
up”, then press
.
GB
(Continued)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using optional equipment
Item
Description
For details, refer to the operating instructions
supplied with the connected equipment. Some
buttons may not work depending on the
connected equipment.
1 BD/DVD
operating
buttons
• ./>: Goes to the
beginning of the previous/
next title/chapter/scene/
track.
•
/
: Replays the scene/
1
Press HDMI 1, HDMI 2, HDMI 3, AV1,
AV2 or COMPONENT.
briefly fast forwards the
scene.
2
3
Press EXT.
• m/M: Fast reverses/fast
forwards the disc when
pressed during playback.
• N: Plays a disc at normal
speed.
While the EXT button lights up, press \/1
to turn the equipment on, then operate the
equipment using the following buttons.
• X: Pauses the playback.
• x: Stops the playback.
TV
HDMI
1
HDMI
2
HDMI
3
EXT
2 F/f/G/g/3
Selects / confirms an item.
Opens the menu.
COMPO-
MONITOR
HDMI
NENT
AV1
AV2
3 HOME
1
4 DVD record • z REC: Starts the
SYNC MENU
THEATRE
DIGITAL/
ANALOG
buttons
AUDIO
recording.
• X REC PAUSE: Pauses the
recording.
• x REC STOP: Stops the
recording.
2
3
5 F1/F2
Selects a function when using
a combination unit (e.g. a
DVD/HDD).
1
4
7
2
3
6
9
5
8
0
6 BD/DVD
Displays the BD/DVD disc
menu.
MENU
PROG
7 BD/DVD
Displays the top menu of the
TOP MENU BD/DVD disc.
REC
REC PAUSE REC STOP
4
5
BD/DVD
TOP MENU MENU
F1
F2
7
6
WIRELESS MENU
TV
z
• The N button has a tactile dot. Use the tactile dot
as a reference when operating other equipment.
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Detaching the Table-Top
Stand from the Monitor
Attaching the Stand for
Media Receiver
Disconnect the mains lead from the monitor
before detaching the Table-Top Stand.
The media receiver can also be used vertically
with the supplied stand.
1
Match the lug on the centre of the stand
and the hole on the right side of the media
receiver.
~
• Remove the screws guided by the arrow marks
of the monitor.
Do not remove the Table-Top Stand for any
reason other than listed below.
– To wall-mount the monitor.
Do not remove the plastic
cover on the Table-Top
Stand.
Stand
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ventilation
s
Never cover the ventilation holes or insert anything in the
cabinet.
Leave space around the TV set as shown below.
It is strongly recommended that you use a Sony wall-mount
bracket in order to provide adequate air-circulation.
Safety
s
s
Information
Monitor
Installed on the wall
Installation/Set-up
Install and use the TV set in accordance with the instructions below
in order to avoid any risk of fire, electrical shock or damage and/or
injuries.
30 cm
10 cm
10 cm
Installation
s
The TV set should be installed near an easily accessible mains
socket.
s
s
Place the TV set on a stable, level surface.
Only qualified service personnel should carry out wall
installations.
s
s
For safety reasons, it is strongly recommended that you use
Sony accessories, including:
10 cm
Leave at least this space around the set.
–
Wall-mount bracket SU-WL500/SU-WL700
Be sure to use the screws supplied with the Wall-mount bracket
when attaching the mounting hooks to the TV set.
The supplied screws are designed so that they are 8 mm to 12
mm in length when measured from the attaching surface of the
mounting hook.
Installed with stand
30 cm
The diameter and length of the screws differ depending on the
Wall-mount bracket model.
6 cm
10 cm
10 cm
Use of screws other than those supplied may result in internal
damage to the TV set or cause it to fall, etc.
8mm – 12mm
Leave at least this space around the set.
Screw (supplied with the Wall-
mount bracket)
Media receiver
Installed horizontally
Mounting Hook
Hook attachment on rear
of TV set
Top
Front
20 cm
Transporting
10 cm
s
s
s
Before transporting the TV set,
disconnect all cables.
8 cm
8 cm
8 cm
8 cm
Two or three people are needed to
transport a large TV set.
When transporting the TV set by
hand, hold it as shown on the right.
Do not put stress on the LCD panel
and the frame around the screen.
Leave at least this space around the set.
Installed vertically
Top
s
s
When lifting or moving the TV set,
hold it firmly from the bottom.
When transporting the TV set, do not
subject it to jolts or excessive
vibration.
Front
20 cm
10 cm
6 cm
s
When transporting the TV set for
repairs or when moving, pack it
using the original carton and packing
material.
6 cm
6 cm
6 cm
Be sure to hold the
bottom of the panel,
not the front part.
Leave at least this space around the set.
s
To ensure proper ventilation and prevent the collection of dirt
or dust:
–
Do not lay the TV set flat, install upside down, backwards,
or sideways.
–
–
Do not place the TV set on a shelf, rug, bed or in a closet.
Do not cover the TV set with a cloth, such as curtains, or
items such as newspapers, etc.
–
Do not install the TV set as shown below.
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
When not in use
Air circulation is
blocked.
Air circulation is
blocked.
s
s
s
If you will not be using the TV set for several days, the TV set
should be disconnected from the mains for environmental and
safety reasons.
As the TV set is not disconnected from the mains when the TV
set is just turned off, pull the plug from the mains to disconnect
the TV set completely.
However, some TV sets may have features that require the TV
set to be left in standby to work correctly.
Wall
Wall
For children
s
s
Do not allow children to climb on the TV set.
Keep small accessories out of the reach of children, so that they
are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the mains lead immediately if any
Mains lead
of the following problems occur.
Handle the mains lead and socket as follows in order to avoid any
risk of fire, electrical shock or damage and/or injuries:
Ask your dealer or Sony service centre to have it checked by
qualified service personnel.
–
Connect the TV set using a three-wire grounding type mains
plug to a mains socket with a protective earthing connection.
Use only mains leads supplied by Sony, not other suppliers.
Insert the plug fully into the mains socket.
Operate the TV set on a 220-240 V AC supply only.
When wiring cables, be sure to unplug the mains lead for your
safety and take care not to catch your feet on the cables.
When:
–
–
–
–
–
–
–
Mains lead is damaged.
Poor fitting of mains socket.
TV set is damaged by being dropped, hit or having something
thrown at it.
–
Any liquid or solid object falls through openings in the cabinet.
–
Disconnect the mains lead from the mains socket before
working on or moving the TV set.
NOTE ON MAINS ADAPTOR
Warning
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
–
–
Keep the mains lead away from heat sources.
Unplug the mains plug and clean it regularly. If the plug is
covered with dust and it picks up moisture, its insulation may
deteriorate, which could result in a fire.
Notes
To prevent fire or shock hazard, do not place objects filled with
liquids, such as vases, on the apparatus.
s
Do not use the supplied mains lead on any other equipment.
s
Do not pinch, bend, or twist the mains lead excessively. The
core conductors may be exposed or broken.
Do not modify the mains lead.
Do not put anything heavy on the mains lead.
Do not pull on the mains lead itself when disconnecting the
mains lead.
Do not install this equipment in a confined space, such as a
bookshelf or similar unit.
s
s
s
s
Please ensure that the mains socket is installed near the
equipment and shall be easily accessible.
s
s
s
s
Be sure to use the supplied mains adaptor and mains lead.
Do not use any other mains adaptor. It may cause a malfunction.
Connect the mains adaptor to an easily accessible mains socket.
Do not coil the mains lead around
the mains adaptor. The core wire
may be cut and/or it may cause a
malfunction of the media receiver.
s
s
Do not connect too many appliances to the same mains socket.
Do not use a poor fitting mains socket.
Prohibited Usage
Do not install/use the TV set in locations, environments or
situations such as those listed below, or the TV set may malfunction
and cause a fire, electrical shock, damage and/or injuries.
s
s
Do not touch the mains adaptor
with wet hands.
If you notice an abnormality in the
mains adaptor, disconnect it from the mains socket
immediately.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other
vessel, inside a vehicle, in medical institutions, unstable locations,
near water, rain, moisture or smoke.
s
The set is not disconnected from the mains source as long as it
is connected to the mains socket, even if the set itself has been
turned off.
Environment:
Places that are hot, humid, or excessively dusty; where insects may
enter; where it might be exposed to mechanical vibration, near
flammable objects (candles, etc).
The TV set shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the TV.
Situation:
Do not use when your hands are wet, with the cabinet removed, or
with attachments not recommended by the manufacturer.
Disconnect the TV set from mains socket and aerial during
lightning storms.
Broken pieces:
s
Do not throw anything at the TV set. The screen glass may
break by the impact and cause serious injury.
s
If the surface of the TV set cracks, do not touch it until you have
unplugged the mains lead. Otherwise electric shock may result.
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
RF Remote
s
If wireless equipment using the same frequency (2.4GHz band)
as the unit is working near the unit, the remote may not operate
properly.
Also, microwave ovens or radio equipment may cause
interference. Keep 2.4 GHz band wireless equipment away
from the unit.
Precautions
Viewing the TV
s
View the TV in moderate light, as viewing the TV in poor light
or during long period of time, strains your eyes.
s
When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
Disposal of the TV set
Disposal of Old Electrical &
LCD Screen
s
Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective,
black dots may appear or bright points of light (red, blue, or
green) may appear constantly on the LCD screen. This is a
structural property of the LCD screen and is not a malfunction.
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
s
s
Do not push or scratch the front filter, or place objects on top of
this TV set. The image may be uneven or the LCD screen may
be damaged.
If this TV set is used in a cold place, a smear may occur in the
picture or the picture may become dark. This does not indicate
a failure. These phenomena disappear as the temperature rises.
This symbol on the product or on its packaging
indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. The recycling of
materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your
local Civic Office, your household waste disposal service or the
shop where you purchased the product.
s
s
s
Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
The screen and cabinet get warm when this TV set is in use.
This is not a malfunction.
The LCD screen contains a small amount of liquid crystal.
Some fluorescent tubes used in this TV set also contain
mercury. Follow your local ordinances and regulations for
disposal.
Handling and cleaning the screen surface/
cabinet of the TV set
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
Be sure to unplug the mains lead connected to the TV set from
mains socket before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
s
To remove dust from the screen surface/cabinet, wipe gently
with a soft cloth. If dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild detergent solution.
This symbol on the battery or on the packaging
indicates that the battery provided with this
product shall not be treated as household
waste. By ensuring these batteries are disposed
s
Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol, benzene,
thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in
damage to the screen surface and cabinet material.
of correctly, you will help prevent potentially negative
consequences for the environment and human health which could
otherwise be caused by inappropriate waste handling of the battery.
The recycling of the materials will help to conserve natural
resources. In case of products that for safety, performance or data
integrity reasons require a permanent connection with an
incorporated battery, this battery should be replaced by qualified
service staff only. To ensure that the battery will be treated
properly, hand over the product at end-of-life to the applicable
collection point for the recycling of electrical and electronic
equipment. For all other batteries, please view the section on how
to remove the battery from the product safely. Hand the battery over
to the applicable collection point for the recycling of waste
batteries. For more detailed information about recycling of this
product or battery, please contact your local Civic Office, your
household waste disposal service or the shop where you purchased
the product.
s
Periodic vacuuming of the ventilation opening is recommended
to ensure to proper ventilation.
Optional Equipment
s
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
s
This equipment has been tested and found to comply with the
limits set out in the EMC Directive using a connection signal
cable shorter than 3 meters.
Wireless Function of the unit
s
If wireless equipment using the same frequency (5GHz band) as
the unit is working near the unit, noise may appear in pictures
or sound, or no picture may result. Also, other wireless or radio
equipment may cause interference. Keep 5GHz band wireless
equipment, such as a wireless LAN or cordless phones, away
from the unit.
s
s
The picture may be influenced depending on the installation
environment or situation of the monitor and media receiver
(page 4).
As the media receiver and monitor communicate wirelessly,
pictures from the media receiver may deteriorate compared to
those from the equipment connected to the monitor with HDMI.
s
s
s
It may take time to transmit pictures depending on the types of
signal, fast motion, such as game pictures, etc.
If pictures from a PC or still images, such as EPG, are
displayed, flickering or blurring may occur.
This unit can be used only in combination with the supplied
monitor and media receiver.
GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote and Unit Controls/Indicators
Remote
As the unit and the supplied remote communicate by radio frequency, you can operate the unit
without aiming the remote at the unit.
TV
Button
Description
1
2
1 TV "/1
Press to turn the unit on and off from standby
mode.
HDMI 1
HDMI 2
AV1
HDMI 3
AV2
EXT
(TV standby)
COMPO-
MONITOR
HDMI
NENT
2 EXT
Press to operate equipment with the IR
Blaster attached, by the remote (page 10).
3
Press to change the subtitle language
(page 36) (in digital mode only).
SYNC MENU
THEATRE
3
4
5
(Subtitle
DIGITAL/
ANALOG
AUDIO
setting)
4 AUDIO
In analogue mode: Press to change the dual
In digital mode: Press to change the language
to be used for the programme currently being
6
7
8
5
/
In digital mode: Displays details of the
programme currently being viewed.
(Info/Text
reveal)
In analogue mode: Displays information.
Press once to display the current channel
number and screen mode. Press again to
display clock information. Press a third time
to remove the display from the screen.
information (e.g. answers to a quiz).
1
4
7
2
3
6
9
5
8
0
6
/
In Text mode: Press to hold the current page.
PROG
(Input select/
Text hold)
7 F/f/G/g/
Press F/f/G/g to move the on-screen cursor.
Press
to select/confirm the highlighted
REC
REC PAUSE REC STOP
item. When playing a photo file: Press
to
BD/DVD
TOP MENU MENU
pause/start a slideshow. Press F/G to select
the previous file. Press f/g to select the next
file.
F1
F2
WIRELESS MENU
8 OPTIONS
Press to display a list that contains “Device
Control”, or shortcuts to some setting menus.
Use the “Device Control” menu to operate
equipment that is compatible with control for
HDMI. The listed options vary depending on
the input source.
TV
z
• The number 5, PROG +,
AUDIO and buttons
have tactile dots. Use the
tactile dots as references
when operating the TV.
GB
(Continued)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Button
Description
TV
9 HOME
Press to display the media receiver Home
or monitor Home menu in the monitor mode
HDMI 1
HDMI 2
AV1
HDMI 3
AV2
EXT
COMPO-
MONITOR
HDMI
NENT
0 Coloured
When the coloured buttons are available, an
operation guide appears on the screen.
Follow the operation guide to perform a
buttons
SYNC MENU
THEATRE
DIGITAL/
ANALOG
AUDIO
qz Number
In TV mode: Press to select channels. For
channel numbers 10 and above, press the
second and third digits in quick succession.
In Text mode: Press to enter a page number.
buttons
w;
ql
qs
(Favourite) Press to display the digital favourite list that
9
0
qd PROG+/–/
/
In TV mode: Press to select the next (+) or
previous (–) channel.
In Text mode: Press to select the next
previous page.
or
1
4
7
2
3
6
9
5
8
0
qa
qs
qf
(Previous
channel)
Press to return to the channel that was last
viewed (for more than five seconds).
qg WIRELESS
Press to display “Wireless Channel Set-up”
qk
qj
MENU
PROG
qd
qf
qh % (Mute)
Press to mute the sound. Press again to
restore the sound.
qh
z
• In standby mode, if you want to turn on the
REC
REC PAUSE REC STOP
monitor without sound, press this button.
BD/DVD
TOP MENU MENU
F1
F2
qj 2/+/–
Press to adjust the volume.
WIRELESS MENU
(Volume)
qg
qk / (Text)
ql RETURN /
Press to return to the previous screen of the
displayed menu. When playing a photo file:
Press to stop the playback. (The display
returns to the file or folder list.)
TV
w; GUIDE /
Press to display the Digital Electronic
(EPG)
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Button
Description
wj
wf
wh
TV
wa ANALOG/
Press to display the analogue or digital
channel that was last viewed.
DIGITAL
HDMI 1
HDMI 2
AV1
HDMI 3
AV2
EXT
COMPO-
MONITOR
HDMI
NENT
ws THEATRE
You can set Theatre Mode to on or off. When
Theatre Mode is set to on, the optimum audio
output (if the unit is connected with an audio
system using an HDMI cable) and picture
quality for film-based contents are
wg
wd
ws
SYNC MENU
THEATRE
DIGITAL/
ANALOG
AUDIO
automatically set.
z
wa
• If you turn the unit off, Theatre Mode is
also turned off.
• “Control for HDMI” (BRAVIA Sync) is
only available with the connected Sony
equipment that has the BRAVIA Sync or
BRAVIA Theatre Sync logo or is
compatible with control for HDMI.
wd SYNC MENU
Displays the menu of connected HDMI
equipment. While viewing other input
screens or TV programmes, “HDMI Device
Selection” is displayed when the button is
pressed.
1
4
7
2
3
6
9
5
8
0
z
• “Control for HDMI” (BRAVIA Sync) is
only available with the connected Sony
equipment that has the BRAVIA Sync logo
or is compatible with control for HDMI.
PROG
wf
REC
REC PAUSE REC STOP
(Screen mode)
BD/DVD
TOP MENU MENU
wg
F1
F2
wg Buttons for
You can operate the equipment connected to
WIRELESS MENU
equipment
wh HDMI1/2/3,
Press to select the input source.
MONITOR
HDMI, AV1/2,
COMPONENT
TV
wj "/1
Press to turn equipment connected to the unit
GB
(Continued)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Media Receiver Buttons and Unit Indicators
Monitor
1
2
3
4
5
6
7
Media Receiver
2
PROG
LINK
HOME
PROG
LINK
HOME
7 6
8
9 0
qa
qs
Item
Description
1 Remote control sensor
Receives IR signals from the remote (if using an IR remote, not
supplied).
Do not put anything over the sensor, as its function may be affected.
2 1 (Power)
Turns the unit on or off.
~
• To disconnect the unit completely, pull the plug from the mains.
3 Light Sensor
Do not put anything over the sensor, as its function may be affected.
4
(Timer indicator)
GB
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
5
6 1 (Standby indicator)
7 " (Power indicator)
8 LINK indicator
Lights up in red when the unit is in standby mode.
Lights up in green when the unit is turned on.
Lights up when the wireless connection between the media receiver and
monitor is stable.
HOME
9
0
(HOME)
Displays the media receiver Home menu in the media receiver mode
/
(Input select/OK) In monitor mode: Selects the input source from equipment connected to
the unit sockets (page 24).
In unit menu: Selects the menu or option, and confirms the setting.
qa 2 +/–/
/
In monitor mode: Increases (+) or decreases (–) the volume.
In unit menu: Moves through the options right ( ) or left ( ).
qs PROG +/–/
/
In TV mode: Selects the next (+) or previous (–) channel.
In unit menu: Moves through the options up ( ) or down ( ).
~
• Make sure that the unit is completely turned off before unplugging the mains lead. Unplugging the mains
lead while the unit is turned on may cause the indicator to remain lit or may cause the unit to malfunction.
• Do not put anything over the indicators as their functions may be affected.
• When the media receiver is used vertically with the stand attached, the qa and qs button functions (in the
unit menu) are exchanged.
GB
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching TV
1
Press 1 on the media receiver or monitor
to switch on.
Watching TV
~
• When either unit is switched on, the other is
also switched on in tandem.
1
When the unit is in standby mode (the 1
(standby) indicator on the unit (front) is
red), press TV "/1 on the remote to switch
on the unit.
2
3
Press DIGITAL/ANALOG to toggle
between digital mode and analogue mode.
The channels available vary depending on
the mode.
1
Press the number buttons or PROG +/– to
select a TV channel.
To select channel numbers 10 and above
using the number buttons, enter the
second and third digits within two
seconds.
TV
To select a digital channel using the
HDMI 1
HDMI 2
AV1
HDMI 3
AV2
EXT
In digital mode
An information banner appears briefly.
The following icons may be indicated on
COMPO-
MONITOR
HDMI
NENT
the banner.
SYNC MENU
THEATRE
: Radio service
DIGITAL/
ANALOG
: Scrambled/Subscription service
: Multiple audio languages available
: Subtitles available
AUDIO
2
: Subtitles available for the hearing
impaired
: Recommended minimum age for current
programme (from 4 to 18 years)
: Parental Lock
Additional operations
1
4
7
2
3
6
9
To
Do this
5
8
0
Turn on the monitor Press %. Press 2 +/– to
from standby mode
without sound
3
3
set the volume level.
Adjust the volume
Press 2 + (increase)/
– (decrease).
PROG
GB
20
Download from Www.Somanuals.com. All Manuals Search And Download.
To access Text
~
• Some characters and/or letters at the top and the
bottom of the picture may not be visible in
“Smart” mode. In such a case, you can select
“Vertical Size” using the “Screen Settings”
(page 31) menu and adjust vertical size to make it
visible.
Press /. Each time you press /, the display
changes cyclically as follows:
Text t Text over the TV picture (mix mode)
t No Text (exit the Text service)
To select a page, press the number buttons or
PROG +/–.
z
To hold a page, press
/
.
• When “Auto Format” is set to “On”, the unit will
automatically select the best mode to suit the
broadcast (page 31).
To reveal hidden information, press
/
.
z
• When four coloured items appear at the bottom of
the Text page, Fastext is available. Fastext allows
you to access pages quickly and easily. Press the
corresponding coloured button to access the page.
• You can adjust the position of the picture when
selecting “Smart”, “14:9” or “Zoom.” Press F/f
to move up or down (e.g. to read subtitles).
Using the Options menu
To change the screen format manually
Press OPTIONS to display the following
options when viewing a TV programme.
Press
repeatedly to select the desired screen
format.
Options
Description
Smart*
Picture Mode
Sound Mode
Speaker
Displays conventional
4:3 broadcasts with an
imitation wide screen
effect. The 4:3 picture
is stretched to fill the
screen.
Motionflow
Subtitle Setting (in
digital mode only)
Sleep Timer
4:3
Power Saving
Displays conventional
4:3 broadcasts (e.g.
non-wide screen TV)
in the correct
Use MONITOR
HDMI
Switch to MONITOR
HDMI input.
(in digital mode only)
proportions.
Wide
Displays wide screen
(16:9) broadcasts in
the correct
proportions.
Zoom*
Displays
cinemascopic (letter
box format)
broadcasts in the
correct proportions.
14:9* (for media receiver inputs only)
Displays 14:9
broadcasts in the
correct proportions.
As a result, black
border areas are
visible on the screen.
* Parts of the top and bottom of the picture may be cut off.
GB
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Digital Electronic Programme Guide (EPG)
*
1
2
In digital mode, press
GUIDE.
All Categories
Today
Fri 16 Mar 11:35
11: 30
12: 00
12: 30
13: 00
Perform the desired operation as shown in
the following table or displayed on the
screen.
001 BBC ONE
002 BBC TWO
003 ITV1
Homes Under the Hammer
Neighbours
Afterlife
Ready Steady Cook Extraordinary People: Britains Iden...
CSI: Crime Scene Inv...
Cracker
Dancing On Ice Exclusive
004 Channel 4
005 Five
Sign Zone: Ancient Rome: The Rise a...
The Jeremy Kyle...
Homes Under th...
PartyPoker.com Worl...
Vodafone TBA: L...
Eastenders
House
Law and Order: Special Victims U...
006 ITV2
Crime Hour: Midsomer Murders
BBC Learning Zone: Schools: World P...
007 BBC THREE
008 BBC FOUR
009 ITV3
A Picture of Brit...
ER
Real Crime: The Truth About the...
Everybody Loves Raymond
This is BBC FOUR
The Sharon Osb...
Trans World Sport
Past
010 SKY THREE
Racing from Chepstow and Ascot
Previous Next
Baseball Wedne...
30 min View
Category
* This function may not be available in some countries.
To
Do this
Watch a programme
Turn off the Guide
Press F/f/G/g to select the programme, then press
Press GUIDE.
.
Sort the programme information by
category
– Category list
1
2
Press the blue button.
Press F/f to select a category, then press
.
Set a programme to be displayed
automatically on the screen when it
starts
1
2
Press F/f/G/g to select the future programme you want to
display, then press
Press F/f to select “Reminder”, then press
A c symbol appears by that programme’s information. The
indicator on the monitor front panel lights up in orange.
/
.
.
– Reminder
~
• If you switch the monitor to standby mode, it will automatically
turn itself on when the programme is about to start.
Cancel a reminder
– Timer list
1
2
3
Press
Press F/f to select “Timer list”, then press
Press F/f to select the programme you want to cancel, then
press
Press F/f to select “Cancel Timer”, then press
/
.
.
.
4
.
A display appears to confirm that you want to cancel the
programme.
5
Press G/g to select “Yes”, then press to confirm.
~
• If an age restriction for programmes has been selected, a message asking for a PIN Code will appear on the
GB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Digital Favourite list
*
1
2
In digital mode, press
.
Favourite Set-up
Digital
Favourites 1
Enter Programme Number:
- - -
Perform the desired operation as shown in
the following table or displayed on the
screen.
001 BBC ONE
011 More 4
012 abc1
002 BBC TWO
003 ITV1
013 QVC
004 Channel 4
005 Five
014 UKTV Gold
015 The HITS
016 UKTV Bright Ideas
017 ftn
006 BBC Three
007 ITV2
008 Sky Sports
009 UKTV History
010 Channel 4+1
018 TMF
019 E4
020 E4+1
Previous
Next
Favourites
2
Digital Favourite list
* This function may not be available in some countries.
To Do this
Create your Favourite list for the first 1 Press F/f/G/g to select the channel you want to add, then press
time
.
Channels that are stored in the Favourite list are indicated by a
symbol.
2
1
2
Press yellow key to select “Favourites 2” or “Favourites 3”.
Watch a channel
Press yellow key to navigate through favourite lists.
Press F/f to select the channel, then press
RETURN.
Press the blue button.
.
Turn off the Favourite list
Press
Add or remove channels in the
currently edited Favourite list
1
2
3
Press the yellow button to choose the list you want to edit.
Press F/f/G/g to select the channel you want to add or remove,
then press
.
Remove all channels from the current 1 Press the blue button.
Favourite list
2
Press the yellow button to select the favourite list you want to
edit.
3
4
Press the blue button.
Press G/g to select “Yes”, then press to confirm.
GB
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Optional Equipment
Connecting Chart
You can connect a wide range of optional equipment to your unit. Connecting cables are not
supplied.
Media receiver
1
2
3
4 5
Rear
AV2
COMPONENT IN
R
L
R
L
PR/CR
PB/CB
Y
AV1
DIGITAL AUDIO
OUT (OPTICAL)
3
2
1
(RGB)
PC IN
DC IN 18V
IN
IR BLASTER
6
7
8
9
Front
PROG
LINK
HOME
0
qa qs
Monitor
Left side
qd
8
GB
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to
Input symbol on
screen
Description
1
2
3
/
/
AV2
AV2
When connecting mono equipment, connect to the
socket.
L
Component The component video sockets support the following video
COMPONENT IN
inputs only: 480i, 480p, 576i, 576p, 720p, 1080i and 1080p.
/
AV1
AV1
When you connect a decoder, the TV tuner outputs scrambled
signals to the decoder, and the decoder unscrambles the
signals before outputting them.
4
Use an optical audio cable.
DIGITAL AUDIO
OUT (OPTICAL)
5 8
RF input that connects to your cable TV system or VHF/UHF.
Connects the supplied mains adaptor.
6 ! DC IN 18V
7
(RGB)/
PC IN
PC
It is recommended to use a PC cable with ferrites, such as the
“Connector, D-sub 15” (ref. 1-793-504-13, available in Sony
Service Centre) or equivalent.
8 HDMI IN 1/2/3,
MONITOR HDMI
IN
HDMI 1/
HDMI 2/
HDMI 3/
Monitor
Digital video and audio signals are input from the connected
equipment.
In addition, when you connect the equipment that is
compatible with control for HDMI, communication with the
this communication.
HDMI
~
• The HDMI sockets support the following video inputs only:
480i, 480p, 576i, 576p, 720p, 1080i, 1080p and 1080/24p
(1080/24p is for MONITOR HDMI only). For PC video
• Be sure to use only an authorised HDMI cable bearing the
HDMI logo.We recommend that you use a Sony HDMI
cable (high speed type).
• For HDMI 1/2/3, when connecting an audio system that is
compatible with control for HDMI, be sure to also connect
it to the DIGITAL AUDIO OUT (OPTICAL) socket.
9 IR BLASTER
Connects the supplied IR Blaster cables.
0
CAM
To use Pay Per View services.
(Conditional
Access Module)
For details, refer to the instruction manual supplied with your
CAM. To use the CAM, remove the “dummy” card from the
CAM slot, then turn off the monitor and insert your CAM card
into the slot. When you are not using the CAM, we recommend
that you keep the “dummy” card in the CAM slot.
~
• CAM is not supported in all countries. Please check with
your authorised dealer.
• If the CAM card becomes jammed while inserting, try
again. Do not insert forcefully.
qa i Headphones
qs USB
You can listen to monitor sound through headphones.
You can enjoy photo files stored in a Sony digital still camera
or camcorder through a USB cable or USB storage device on
qd SERVICE ONLY
For service use only.
GB
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Option
Description
Viewing Pictures from
Connected Equipment
PC/HDMI PC input
mode)
Switch on the connected equipment, then
perform one of the following operation.
Power Saving
Use MONITOR
HDMI
Switch to MONITOR
HDMI input.
For equipment connected to the scart
PC/HDMI PC input
mode only)
sockets using a fully-wired 21-pin scart lead
Start playback on the connected equipment.
The picture from the connected equipment
appears on the screen.
Horizontal Shift (in
PC/HDMI PC input
mode only)
For an auto-tuned VCR/ DVD recorder
Device Control (in
HDMI input mode
only)
In analogue mode, press PROG +/–, or the
number buttons, to select the video channel.
When equipment is connected to the
MONITOR HDMI socket
For equipment connected to MONITOR
HDMI socket
Press MONITOR HDMI.
Option
Description
Picture Adjustment
Sound
For other connected equipment
Press
equipment. Press F/f to select the desired
input source, then press
/
to display a list of connected
Power Saving
HDMI PC input
mode)
.
The highlighted item is automatically selected
if you do not perform any operation for two
seconds after pressing F/f.
If you have set an input source to “Skip” in the
does not appear in the list.
Horizontal Shift (in
HDMI PC input
mode only)
Vertical Shift (in
HDMI PC input
mode only)
z
• To return to normal TV mode, press DIGITAL/
ANALOG.
Device Control
HDMI Device
Selection
Using the Options menu
Use Media Receiver Switch to media receiver
inputs.
Press OPTIONS to display the following
options when viewing pictures from connected
equipment.
If wireless communication is not successful
Option
Description
When equipment is connected to the media
receiver sockets
Wireless Channel
Set-up
Option
Description
Use MONITOR
HDMI
Switch to MONITOR
HDMI input.
PC/HDMI PC input
mode)
Sound Mode
Speaker
PC/HDMI PC input
mode)
GB
26
Download from Www.Somanuals.com. All Manuals Search And Download.
• While the unit is accessing the data on the USB
device, observe the following:
– Do not turn off the unit or connected USB
device.
– Do not disconnect the USB cable.
– Do not remove the USB device.
Using USB Photo Viewer
You can enjoy photo files stored in a Sony
digital still camera or camcorder through a
USB cable or USB storage media on your unit.
The data on the USB device may be damaged.
• Sony will not be held liable for any damage to, or
loss of, data on the recording media due to a
malfunction of any connected devices or the unit.
• USB photo viewer supports DCF-compliant JPEG
photographs only.
• When you connect a Sony digital still camera, set
the camera’s USB connection mode to Auto or
“Mass Storage.” For more information about USB
connection mode, refer to the instructions supplied
with your digital camera.
1
Connect a supported USB device to the
media receiver.
2
3
Press HOME.
Press G/g to select “Photo”, then press F/
f to select “USB Photo Viewer” and press
.
The thumbnail screen appears.
4
5
Press F/f/G/g to select a file or folder,
then press
When you select a folder, select a file,
then press
.
• USB Photo Viewer supports FAT32 file system
only.
• Depending on the exact file specifications, some
files, including those modified on a PC, cannot be
played even if the file format is supported.
• Check the website below for updated information
about compatible USB devices.
.
Playback starts.
Press RETURN to go back to the
thumbnail screen.
Additional operations
To display a photograph
— Picture Frame
Option
Description
Device Selection
Press G/g to select a
device when multiple
devices are connected.
BRAVIA images are
predefined device.
You can display a photograph on the screen
for a selected period of time. After that period,
the unit automatically switches itself into
standby mode.
Slideshow
Set-up
Displays the photographs
one by one.
1
2
Press HOME.
Press G/g to select “Photo”, then press F/
f to select “Picture Frame” and press
You can make advanced
settings for a slide show,
and set the display
sequence of the
.
To select a photograph
Press OPTIONS, then select “Image
Selection” and press . Then, select a
thumbnails.
photograph, and press
To set the duration of displaying a
photograph
Press OPTIONS, then select “Duration”
and press . Then, select the duration,
to set.
(Photo) Available Options
Option
Description
Picture Mode
Sleep Timer
Power Saving
and press
.
The counter appears on the screen.
To return to the XMB™
Press RETURN.
~
• Picture quality may appear coarse when using
(Photo) because images may be enlarged
depending on the file. Also, images may not fill
the entire screen depending on the image size and
aspect ratio.
~
• If the photograph is selected from a USB device, it
must remain connected to the unit.
• If “Sleep Timer” is activated, the unit
automatically will switch into standby mode.
• Some photo files may take some time to be
displayed when using
(Photo).
GB
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To make the control for HDMI settings
Using BRAVIA Sync with
Control for HDMI
The control for HDMI function enables the
unit to communicate with the connected
equipment that is compatible with the
function, using HDMI CEC (Consumer
Electronics Control).
The control for HDMI settings must be set on
both the unit side and connected equipment
unit side settings. For settings on the
connected equipment, refer to the operating
instructions for that equipment.
* Function only available when connected to HDMI 1/2/3.
For example, by connecting Sony equipment
that is compatible with control for HDMI
(with HDMI cables), you can control them
together.
Be sure to connect the equipment correctly,
and make the necessary settings.
Control for HDMI
•
•
Automatically turns the connected
equipment off when you switch the unit to
standby mode using the remote.
Automatically turns the unit on and
switches the input to the connected
equipment when the equipment starts to
play.
•
If you turn on a connected audio system
while the unit is on, the sound output
switches from the monitor speaker to the
audio system.*
•
•
Adjusts the volume (2 +/–) and mutes the
sound (%) of a connected audio system.*
You can operate the connected Sony
equipment that has the BRAVIA Sync logo
by the supplied remote by pressing:
– N/x/X/m/M to operate the connected
equipment directly.
– SYNC MENU to display the menu of the connected
HDMI equipment on the screen.
After displaying the menu, you can operate the
menu screen by using F/f/G/g and
.
– OPTIONS to display “Device Control”, then select
options from “Menu”, “Options”, and “Content
List” to operate the equipment.
– Refer to the instruction manual of the equipment for
available control.
To connect the equipment that is
compatible with control for HDMI
Connect the compatible equipment and the
unit with an HDMI cable. When connecting an
audio system*, be sure to also connect the
DIGITAL AUDIO OUT (OPTICAL) socket
of the media receiver and the audio system
using an optical audio cable. For details, see
GB
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using MENU Functions
Navigating through Media Receiver Home Menu (XMB™)
For setting the menu of the media receiver, switch to the media receiver mode by pressing one of
The XMB™ (XrossMediaBar) is a menu of BRAVIA features and input sources displayed on the
monitor screen. The XMB™ is an easy way to select programming and adjust settings on your
media receiver.
1
Press HOME.
The media receiver Home menu appears on the screen.
Picture
Sound
Media Category Bar
Settings
Features
Media Receiver Set-up
Monitor
Set-up
Analogue Set-up
Category Object Bar
2
Press G/g to select the category.
Media category icon
Settings
Description
You can make advanced settings and adjustments. For details about
Photo
Digital
You can also select a channel using the number buttons or PROG +/–.
Analogue
You can select an analogue channel.
You can also select a channel using the number buttons or PROG +/–.
To hide the list of analogue channels, set “Programme List Display” to
External Inputs
You can select equipment connected to the media receiver.
3
Press F/f to select the item, then press
Follow the instructions on the screen.
Press HOME to exit.
.
4
5
~
• The options you can adjust vary depending on the situation.
• Unavailable options are greyed out or not displayed.
GB
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Picture
Sound
See the “Sound” setting for monitor (page 41).
Features
Quick Start
The unit turns on faster than usual within two hours after switching to standby
mode. However, power consumption in standby mode is 38 watt higher than usual.
Timer Settings
Sets the timer to turn on/off the unit.
Sleep Timer
Sets a period of time after which the unit automatically
switches itself into standby mode.
When the “Sleep Timer” is activated, the (Timer) indicator
on the monitor (front panel) lights up in orange.
z
• If you turn off the unit and turn it on again or switch to the
monitor mode from the media receiver mode, “Sleep
Timer” is reset to “Off.”
• A notification message appears on the screen one minute
before the unit switches to standby mode.
On Timer
Settings
On Timer
Sets the timer to turn on the unit from
standby mode.
Timer Mode
Sets the desired day(s) of the week you
want the timer to turn on the unit.
Time
Sets the time to turn on the unit.
Duration
Sets how long you want the unit to stay
on before switching to standby mode
again.
z
• If you switch to the monitor mode from the media receiver
mode, “Duration” is cancelled.
Clock Set
Allows you to adjust the clock manually. When the unit is
receiving digital channels, the clock cannot be adjusted
manually since it is set to the time code of the broadcasted
signal.
GB
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Media Receiver Set-up
Auto Start-up
Starts the “first time operation menu” to select the language, country and location,
and tune in all available digital and analogue channels. Usually, you do not need to
do this operation because the language and country will have been selected and
option allows you to repeat the process (e.g., to retune the unit after moving house,
or to search for new channels that have been launched by broadcasters).
Screen Settings
Auto Format
Automatically changes the screen format according to the
input signal. To keep your setting, select “Off.”
Display Area
Adjusts the picture display area in 1080i/p and 720p sources
when “Screen Format” is set to “Wide.”
Auto
During digital broadcasts, displays
pictures in accordance with the settings
recommended by the broadcast station.
Full Pixel
Normal
Displays pictures in their original size.
Displays pictures in their recommended
size.
Horizontal Shift Adjusts the horizontal position of the picture.
Vertical Shift
Adjusts the vertical position of the picture when “Screen
Format” is set to “Smart”, “Zoom” or “14:9.”
Vertical Size
Adjusts the vertical size of the picture when “Screen Format”
is set to “Smart”, “Zoom” or “14:9.”
PC Settings
Screen Format Selects a screen format for displaying input from your PC.
Full 1
Enlarges the picture to fill the vertical
display area, keeping its original
horizontal-to-vertical aspect ratio.
Full 2
Enlarges the picture to fill the display
area.
Reset
Resets the PC screen settings to the factory settings.
Auto Adjustment Automatically adjusts the display position, phase and pitch of
the picture when the unit receives an input signal from the
connected PC.
z
• “Auto Adjustment” may not work well with certain input
signals. In such cases, manually adjust “Phase”, “Pitch” and
“Horizontal Shift.”
Phase
Pitch
Adjusts the phase when the screen flickers.
Adjusts the pitch when the picture has unwanted vertical
stripes.
Horizontal Shift Adjusts the horizontal position of the picture.
Power
Management
Switches the unit to standby mode if no signal is received for
30 seconds in the PC input.
GB
(Continued)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
AV Set-up
AV Preset
Assigns a name to any equipment connected to the media
receiver. The name will be displayed briefly on the screen
when the equipment is selected. You can skip an input source
that is not connected to any equipment.
1
Press F/f to select the desired input source, then press
.
2
Press F/f to select the desired option below, then press
.
-, CABLE, SAT, Uses one of the preset labels to assign a
VCR, DVD/BD, name to connected equipment.
GAME, AUDIO
SYSTEM, CAM,
PC
Edit:
Creates your own label.
1
Press F/f to select the desired letter
or number (“_” for a blank space),
then press g.
If you input a wrong character
Press G/g to select the wrong
character. Then, press F/f to select
the correct character.
2
3
Repeat the procedure in step 1 until
the name is completed.
Select “OK”, then press
.
Skip
Skips an input source that is not
connected to any equipment when you
press F/f to select the input source.
Speaker
Turns on/off the monitor’s internal speakers.
TV Speaker The monitor speakers are turned on in
order to listen to the TV’s sound through
the monitor speakers.
Audio System The monitor speakers are turned off in
order to listen to the TV’s sound only
through your external audio equipment
connected to the audio output sockets.
When connected with “Control for
HDMI” compatible equipment, you can
turn the connected equipment on
interlocked with the monitor. This setting
must be made after connecting the
equipment.
Dual Sound
Selects the sound from the speaker for a stereo or bilingual broadcast.
Stereo/Mono
A/B/Mono
For a stereo broadcast.
For a bilingual broadcast, select “A” for sound channel 1, “B”
for sound channel 2, or “Mono” for a mono channel, if
available.
z
• If you select other equipment connected to the unit, set “Dual Sound” to
“Stereo”, “A” or “B.”
IR Blaster Set-up
GB
32
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI Set-up
This is used to set the “Control for HDMI” compatible equipment connected to the
HDMI sockets. Note that the interlock setting must also be made on the connected
“Control for HDMI” compatible equipment side.
Control for HDMI This sets whether to interlock the “Control for HDMI”
compatible equipment and the unit. When set to “On”, the
following menu items can be performed. However, power
consumption in standby mode is higher than usual. If the
specific Sony equipment that is compatible with “Control for
HDMI” is connected, this setting is applied to the connected
equipment automatically when the “Control for HDMI” is set
to “On” using the unit.
Auto Devices Off When this is set to “On”, the “Control for HDMI” compatible
equipment turns off when you switch the unit to standby
mode using the remote.
Auto TV On
When this is set to “On” and if the connected HDMI control
compatible equipment is turned on, the unit automatically
turns on, and the displays the HDMI input from the
connected equipment.
Device List
Update
Creates or updates the “HDMI Device List.” Up to 14
“Control for HDMI” compatible equipment can be
connected, and up to 4 equipment can be connected to a
single socket. Be sure to update the “HDMI Device List”
when you change the “Control for HDMI” compatible
equipment connections or settings. Select them manually one
by one until getting a correct picture for several seconds.
HDMI Device List Displays the connected “Control for HDMI” compatible
equipment.
Product Information Displays your media receiver’s product information.
Select “Monitor Product Information” to display your monitor’s product
information.
All Reset
Resets all settings to the factory settings and then displays the “Auto Start-up”
screen.
z
• Be sure not to turn the unit off during this period (it takes about 30 seconds) or
press any buttons.
• All settings, including digital favourite list, country, language, auto tuned
channels, etc. will be reset.
Monitor Set-up
Analogue Set-up
Programme List
Display
Select “Off” to hide the list of analogue channels from the XMB™
(XrossMediaBar).
Auto Tuning
Tunes in all the available analogue channels.
This option allows you to retune the unit after moving house, or to search for new
channels that have been launched by broadcasters.
GB
(Continued)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme Sorting Changes the order in which the analogue channels are stored on the unit.
1
Press F/f to select the channel you want to move to a new position, then press
.
2
Press F/f to select the new position for your channel, then press
.
Manual Programme Before selecting “Label/AFT/Audio Filter/LNA/Skip”, press PROG +/– to select
the programme number with the channel. You cannot select a programme number
Preset
Programme/
System/Channel
Presets programme channels manually.
1
2
Press F/f to select “Programme”, then press
Press F/f to select the programme number you want to
manually tune (if tuning a VCR/ DVD recorder, select
.
channel 00), then press
Press F/f to select “System”, then press
Press F/f to select one of the following TV broadcast
systems, then press RETURN.
RETURN.
3
4
.
B/G: For western European countries
I: For the United Kingdom
D/K: For eastern European countries
L: For France
5
6
Press F/f to select “Channel”, then press
Press F/f to select “S” (for cable channels) or “C” (for
terrestrial channels), then press g.
.
7
Tune the channels as follows:
If you do not know the channel number
(frequency)
Press F/f to search for the next available channel. When
a channel has been found, the search will stop. To
continue searching, press F/f.
If you know the channel number (frequency)
Press the number buttons to enter the channel number of
the broadcast you want or your VCR/DVD recorder
channel number.
8
9
Press to jump to “Confirm”, then press
Press f to select “OK”, then press
.
.
Repeat the procedure above to preset other channels
manually.
Label
AFT
Assigns a name of your choice, up to five letters or numbers,
to the selected channel. This name will be displayed briefly
on the screen when the channel is selected.
To input characters, follow steps 1 to 3 of “Edit:” (page 32).
Allows you to fine-tune the selected programme number
manually if you feel that a slight tuning adjustment will
improve the picture quality.
You can adjust the fine tuning over a range of –15 to +15.
When “On” is selected, the fine tuning is performed
automatically.
GB
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Filter
Improves the sound for individual channels in the case of
distortion in mono broadcasts. Sometimes a non-standard
broadcast signal can cause sound distortion or intermittent
sound muting when watching mono programmes.
If you do not experience any sound distortion, we
recommend that you leave this option set to the factory
setting “Off.”
~
• You cannot receive stereo or dual sound when “Low” or
“High” is selected.
LNA
Improves the picture quality for individual channels in the
case of very weak broadcast signals (noisy picture).
If you cannot see any improvement in the picture quality even
if you set to “On”, set this option to “Off” (factory setting).
Skip
Skips unused analogue channels when you press PROG +/–
to select channels. (You can still select a skipped channel
using the number buttons.)
Confirm
Saves changes made to the “Manual Programme Preset”
settings.
Digital Set-up
Digital Tuning
Digital Auto
Tuning
Tunes in the available digital channels.
This option allows you to retune the unit after moving house,
or to search for new channels that have been launched by
broadcasters. For details, see step 6 of “Performing the initial
set-up” (page 8).
Programme
Sorting
Removes any unwanted digital channels stored on the unit,
and changes the order of the digital channels stored on the
unit.
1
Press F/f to select the channel you want to remove or
move to a new position.
You can also select a channel by pressing the number
buttons to enter its three-digit channel number.
2
Remove or change the order of the digital channels as
follows:
To remove the digital channel
Press . After a confirmation message appears, press G
to select “Yes”, then press
.
To change the order of the digital channels
Press g, then press F/f to select the new position for the
channel and press G.
3
Press
RETURN.
Digital Manual
Tuning
Tunes the digital channels manually. This feature is available
when “Digital Auto Tuning” is set to “Antenna.”
1
Press the number button to select the channel number
you want to manually tune, then press F/f to tune the
channel.
2
3
When the available channels are found, press F/f to
select the channel you want to store, then press
Press F/f to select the programme number where you
want to store the new channel, then press
.
.
Repeat the above procedure to manually tune other channels.
GB
(Continued)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Subtitle Set-up
Audio Set-up
Subtitle Setting When “For Hard Of Hearing” is selected, some visual aids
may also be displayed with the subtitles (if TV channels
broadcast such information).
Subtitle
Language
Allows you to select the language of the subtitles.
Audio Type
Switches to broadcast for the hearing impaired when “For
Hard Of Hearing” is selected.
Audio Language Selects the language used for a programme. Some digital
channels may broadcast several audio languages for a
programme.
Audio
Description
Provides audio description (narration) of visual information if
TV channels broadcast such information.
Mixing Level*
Adjusts the unit main audio and Audio Description output
levels.
Dynamic Range Compensates for differences in the audio level between
different channels. Note that this function may have no effect
for some channels.
Optical Out
Selects the audio signal that is output from the DIGITAL
AUDIO OUT (OPTICAL) terminal on the rear of the media
receiver. Set to “Auto” when equipment compatible with
Dolby Digital is connected, and set to “PCM” when non-
compatible equipment is connected.
z
* This option is only available when “Audio Description” is set to “On.”
Radio Display
Parental Lock
Displays the screen wallpaper when you listen to a radio broadcast after 20 seconds
without pressing any buttons.
You can select the screen wallpaper colour, display a random colour or view a
slide show (page 27).
To cancel the screen wallpaper display temporarily, press any button.
Sets an age restriction for programmes. Any programme that exceeds the age
restriction can only be watched after a PIN Code is entered correctly.
1
Press the number buttons to enter your existing PIN Code.
If you have not previously set a PIN, a PIN Code entry screen appears. Follow
the instructions of “PIN Code” below.
2
3
Press F/f to select the age restriction or “None” (for unrestricted watching),
then press
.
Press
RETURN.
PIN Code
To set your PIN for the first time
1
2
Press the number buttons to enter the new PIN Code.
Press RETURN.
To change your PIN
1
Press the number buttons to enter your existing PIN Code.
2
Press the number buttons to enter the new PIN Code.
3
Press
RETURN.
z
• PIN Code 9999 is always accepted.
Technical Set-up
Auto Service
Update
Enables the unit to detect and store new digital services as
they become available.
~
• For the service update to be able to take place the unit should be left in standby
mode from time to time.
GB
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Software
Download
Enables the unit to automatically receive software updates
free through your existing aerial/cable (when issued). We
recommend that you leave the setting to “On” at all times.
If you do not want your software to be updated, set this
option to “Off.”
~
• For the software upgrade to be able to take place the unit should be left in standby
mode from time to time.
System
Information
Displays the current software version and the signal level.
~
• If signal bar is red (no signal) or amber (low signal), check the aerial/cable
connection.
Time Zone
Allows you to manually select the time zone you are in, if it is
not the same as the default time zone setting for your country.
Auto DST
Sets whether or not to automatically switch between summer
time and winter time.
On
Automatically switches between summer
time and winter time according to the
calendar.
Off
The time is displayed according to the
time difference set by “Time Zone.”
CA Module Set-up
Allows you to access a pay TV service once you obtain a Conditional Access
(PCMCIA) socket.
GB
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigating through Monitor Home Menu
For setting the menu of the monitor, switch to the monitor mode by pressing MONITOR HDMI on
the remote.
1
Press HOME.
The monitor Home menu appears on the screen.
Monitor Menu
Picture
Sound
Screen
HDMI Set-up
Monitor Set-up
PC Settings
2
Press F/f to select the item, then press
Follow the instructions on the screen.
Press HOME to exit.
.
3
4
~
• The options you can adjust vary depending on the situation.
• Unavailable options are greyed out or not displayed.
GB
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Picture Adjustment
Picture Mode
Selects the picture mode except for PC input source. “Picture
Mode” includes options best suited for video and
photographs, respectively. The options that can be selected
differ depending on the input source.
Vivid
For enhanced picture contrast and
sharpness.
Standard
Cinema
For standard picture. Recommended for
home entertainment.
For viewing film-based content. Most
suitable for viewing in a theatre-like
environment.
Custom
Allows you to store your preferred
settings.
Photo-Vivid
For viewing photographs. Enhances
picture contrast and sharpness.
Photo-Standard For viewing photographs. Provides the
optimum picture quality for viewing in
the home.
Photo-Original For viewing photographs. Represents the
picture quality used when imaging
developed photographs.
Photo-Custom Allows you to store your preferred
settings.
Reset
Resets all picture settings except “Picture Mode” to the
factory settings.
Backlight
Contrast
Brightness
Colour
Adjusts the brightness of the backlight.
Increases or decreases picture contrast.
Brightens or darkens the picture.
Increases or decreases colour intensity.
Increases or decreases the green and red tones.
Hue
z
• “Hue” can only be adjusted for an NTSC colour signal (e.g.,
U.S.A. video tapes).
Colour
Adjusts the whiteness of the picture.
Temperature
Cool
Gives the white colours a blue tint.
Gives the white colours a neutral tint.
Neutral
Warm 1/Warm 2 Gives white colours a red tint. “Warm 2”
gives a redder tint than “Warm 1.”
z
• “Warm 1” and “Warm 2” are not available when “Picture
Mode” is set to “Vivid” (or “Photo-Vivid”).
Sharpness
Sharpens or softens the picture.
GB
(Continued)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise Reduction Reduces the picture noise (snowy picture) in a weak
broadcast signal.
Auto
Automatically reduces the picture noise
(in analogue mode only).
High/Medium/ Modifies the effect of the noise reduction.
Low
Off
Turns off the “Noise Reduction” feature.
MPEG Noise
Reduction
Reduces picture noise in MPEG-compressed videos. This is
effective when viewing a DVD or digital broadcast.
Advanced
Settings
Allows you to set “Picture” settings in more detail. These
settings are not available when “Picture Mode” is set to
“Vivid” (or “Photo-Vivid”).
Reset
Resets all the advanced settings to the
factory settings.
Black Corrector Enhances black areas of the picture for
stronger contrast.
Adv. Contrast Automatically adjusts “Backlight” and
Enhancer
“Contrast” to the most suitable settings
judging from the brightness of the screen.
This setting is especially effective for
dark images scenes. It will increase the
contrast distinction of the darker picture
scenes.
Gamma
Adjusts the balance between light and
dark areas of the picture.
Clear White
Emphasises white and light colours.
Colour Space Changes the colour reproduction gamut.
“Wide” reproduces the vivid colour and
“Standard” reproduces the standard
colour.
Live Colour
Makes colours more vivid.
White Balance Adjusts the colour temperature in detail.
~
• “Live Colour” is not available when “Colour Space” is set
to “Standard.”
Motionflow
Provides smoother picture movement and reduces picture blur.
High
Provides smoother picture movement such as for film-based
contents.
Standard
Off
Provides smooth picture movement. Use this setting for
standard use.
Use this setting when the “High” and “Standard” settings
result in noise.
~
• Depending on the video, you may not see the effect visually, even if you have
changed the setting.
GB
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Film Mode
Provides an improved picture quality which is optimised for film when playing
DVD images taken on film.
Auto 1/Auto 2
“Auto 1” provides smoother picture movement than the
original film-based content. “Auto 2” provides the original
film-based content as is.
Off
Turns off the “Film Mode” feature.
~
• If the image contains irregular signals or too much noise, “Film Mode” will be
automatically turned off even if “Auto 1/Auto 2” is selected.
• “Film Mode” is not available when “Video/Photo” is set to “Photo” or when
photograph is detected if “Video-A” is set.
Game Mode
Video/Photo
Provides the optimum screen for viewing images with fine lines and characters that
are input from video game equipment and PCs. Set to “On” for the sharp display of
fine lines or characters.
Provides suitable image quality by selecting the option depending on the input
source (video or photograph data).
Video-A
Sets suitable image quality, depending on the input source,
video data or photograph data when directly connecting Sony
HDMI output-capable equipment that supports “Video-A”
mode.
Video
Photo
Produces suitable image quality for moving pictures.
Produces suitable image quality for still images.
~
• The setting is fixed to “Video” when “Video-A” mode is not supported on the
connected equipment, even if “Video-A” is selected.
• Only available for HDMI 1, HDMI 2, HDMI 3, MONITOR HDMI and
Component in format 1080i or 1080p.
~
• Some options are not available in PC/HDMI PC input mode.
Sound
Sound Mode
Selects the sound mode.
Dynamic
Enhances the treble and bass sounds.
Standard
Clear Voice
For standard sounds.
Makes voice sound clearer.
Reset
Resets all the sound settings to the factory settings excluding “Dual Sound.”
Adjusts higher-pitched sounds.
Treble
Bass
Adjusts lower-pitched sounds.
Balance
Surround
Emphasises left or right speaker balance.
S-FORCE Front Provides a virtual surround sound experience made possible
Surround
using just two front speakers.
Off
Selects for normal stereo or mono reception.
Voice Zoom
Adjusts the sound level of human voices. For example, if the voice of a news
announcer is indistinct, you can turn up this setting to make the voice louder.
Conversely, if you are watching a sports programme, you can turn down this
setting to soften the voice of the commentator.
Sound Booster
Produces a fuller sound for more impact, by emphasising the treble and bass
sounds.
GB
(Continued)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Volume
Volume Offset
~
Keeps a constant volume level even when volume level gaps occur (e.g., adverts
tend to be louder than programmes).
Adjusts the volume level of the current input relative to other inputs.
• Some options are not available when “Speaker” is set to “Audio System” or headphones are connected.
Screen
Screen Format
Auto Format
Automatically changes the screen format according to the input signal. To keep
your setting, select “Off.”
4:3 Default
Selects the default screen format for use with 4:3 broadcasts.
Smart
Displays conventional 4:3 broadcasts with an imitation wide
screen effect.
4:3
Displays conventional 4:3 broadcasts in the correct
proportions.
Off
Keeps the current “Screen Format” setting when the channel
or input is changed.
Display Area
Adjusts the picture display area in 1080i/p and 720p sources when “Screen
Format” is set to “Wide.”
Full Pixel
Displays pictures in their original size if the input source is
1080i/p.
Normal
-1/-2
Displays pictures in their recommended size.
Enlarges the picture to hide the edges of the picture.
Horizontal Shift
Vertical Shift
Vertical Size
Adjusts the horizontal position of the picture.
Adjusts the vertical position of the picture when “Screen Format” is set to “Zoom.”
Adjusts the vertical size of the picture when “Screen Format” is set to “Smart” or
“Zoom.”
HDMI Set-up
This is used to set the “Control for HDMI” compatible equipment connected to the HDMI sockets.
Note that the interlock setting must also be made on the connected “Control for HDMI” compatible
equipment side.
Control for HDMI
This sets whether to interlock the “Control for HDMI” compatible equipment and
the unit. When set to “On”, the following menu items can be performed. However,
power consumption in standby mode is higher than usual.
Auto Devices Off
Auto TV On
When this is set to “On”, the “Control for HDMI” compatible equipment turns off
when you switch the unit to standby mode using the remote.
When this is set to “On” and if the connected HDMI, control compatible
equipment is turned on, the unit automatically turns on, and the displays the HDMI
input from the connected equipment.
Device List Update
Creates or updates the “HDMI Device List.” Up to 14 “Control for HDMI”
compatible equipment can be connected, and up to 4 equipment can be connected
to a single socket. Be sure to update the “HDMI Device List” when you change the
“Control for HDMI” compatible equipment connections or settings. Select them
manually one by one until getting a correct picture for several seconds.
HDMI Device List
Displays the connected “Control for HDMI” compatible equipment.
GB
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor Set-up
Power Saving
Light Sensor
Reduces the power consumption by adjusting the backlight brightness. This also
enhances the black level. Select from “Off”, “Low”, “High” and “Picture Off”.
On
Automatically optimises the picture settings according to the
ambient light in the room.
Off
Turns off the “Light Sensor” feature.
~
• Be sure not to put anything over the sensor, as its function may be affected. See
page 18 for the location of the light sensor.
Product Information Displays your monitor’s product information.
Remote Control Set- Registers a remote to the unit, otherwise the remote cannot be used with the unit.
Instruction screens appear if you register or delete a remote. Follow the
instructions to register or delete.
up
~
• The remote can only be registered to only one unit.
Wireless Channel
Set-up
Wireless
Channel
Selection
Selects a wireless channel from “Auto”, “36ch”, “40ch”,
“44ch” or “48ch”.
If the wireless channel is uncertain, select “Auto” to search
an available channel.
Wireless
Information
Displays information about the current wireless channel.
Language
Selects the language in which the menus are displayed.
Logo Illumination
Lights up and turns off the Sony logo on the front of the monitor.
PC Settings
Screen Format
Selects a screen format for displaying input from your PC.
Normal
Full 1
Displays the picture in its original size.
Enlarges the picture to fill the vertical display area, keeping
its original horizontal-to-vertical aspect ratio.
Full 2
Enlarges the picture to fill the display area.
Reset
Resets the PC screen settings to the factory settings.
Adjusts the horizontal position of the picture.
Adjusts the vertical position of the picture.
Horizontal Shift
Vertical Shift
GB
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Installing the Accessories (Wall-Mount Bracket)
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of your
monitor be performed by Sony dealers or licenced contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Your monitor can be installed using the Wall-Mount Bracket SU-WL500/SU-WL700 (sold
separately). For SU-WL500, install as illustrated below. For SU-WL700, see the manual supplied
with SU-WL700.
•
Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the
installation.
•
•
•
Refer to “Detaching the Table-Top Stand from the Monitor” (page 11).
Screw
(+PSW6 × 16)
1
2
Screw
Mounting
Hook
Square hole
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for
withstanding the monitor’s weight. Be sure to entrust the attachment of this product to the wall to Sony
dealers or licenced contractors and pay adequate attention to safety during the installation. Sony is not liable
for any damage or injury caused by mishandling or improper installation.
GB
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor installation dimensions table
Screen centre point
Unit: mm
Length for each mounting angle
Screen centre
dimension
Display dimensions
Model Name
Angle (0°)
Angle (20°)
A
B
C
D
E
F
G
H
KDL-52EX1
KDL-46EX1
KDL-40EX1
1,312
1,156
1,024
806
709
635
80
486
464
464
114
110
110
351
321
296
765
674
604
508
486
486
107
144
Figures in the above table may differ slightly depending on the installation.
WARNING
The wall that the monitor will be installed on should be capable of supporting a weight of at least four times
Screw and Hook locations diagram/table
Model Name
Screw location
Hook location
KDL-52EX1/46EX1/40EX1
e, j
b
* Hook position “a” and “c” cannot be used for the models in the table above.
Screw location
Hook location
a*
b
c*
GB
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Media receiver
Model name
System
MBT-W1
Analogue: Depending on your country selection: B/G/H, D/K, L, I
Digital: DVB-T/DVB-C
TV system
Analogue: PAL, SECAM NTSC 3.58, 4.43 (only Video In)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC [email protected], [email protected]
Colour/video system
Channel coverage
Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF
Input/Output jacks
75 ohm external terminal for VHF/UHF
Aerial
21-pin Scart connector (CENELEC standard) including audio/video input, RGB input and unit
audio/video output.
/
AV1
Video input (phono jack)
AV2
AV2
Audio input (phono jacks)
DIGITAL AUDIO OUT (OPTICAL)(digital optical jack)
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync
PB/CB: 0.7 Vp-p, 75 ohms
COMPONENT IN
PR/CR: 0.7 Vp-p, 75 ohms
Audio input (phono jacks)
500 mVrms
COMPONENT IN
Video: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
HDMI IN 1, 2, 3
32, 44.1 and 48 kHz, 16, 20 and 24 bits
PC Input (see page 48)
PC Input (D-sub 15-pin)
PC IN
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms, non Sync on Green
R: 0.7 Vp-p, 75 ohms, non Sync on Green
HD: 1-5 Vp-p
VD: 1-5 Vp-p
PC audio input (minijack)
CAM (Conditional Access Module) slot
Headphones jack
i
USB port
Power and others
Power requirements
220–240 V AC, 50 Hz
20 W
Power consumption
3.5 W or less (19 W when Quick Start is ON)
13.1 × 30.2 × 28.6 cm
Standby power consumption*
Dimensions
(Approx.)
for vertical
placement with
stand
(w × h × d)
28.0 × 7.2 × 28.6 cm
2.5 kg
for horizontal
placement
Mass(Approx.) for vertical
placement with
stand
2.4 kg
for horizontal
placement
GB
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor
Model name
System
LDM-E521
LDM-E461
LDM-E401
LCD (Liquid Crystal Display) Panel
8 W + 8 W
Panel system
Sound output
Input/Output jacks
MONITOR HDMI IN
Video: 1080/24p, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits
PC Input (see page 48)
Power and others
220–240 V AC, 50 Hz
Power requirements
52 inches (Approx. 132.2 cm) 46 inches (Approx. 116.8 cm) 40 inches (Approx. 101.6 cm)
1,920 dots (horizontal) × 1,080 lines (vertical)
Screen size (measured diagonally)
Display resolution
295 W
220 W
180 W
Power
in “Home”/
consumption
“Standard” mode
324 W
247 W
221 W
in “Shop”/“Vivid”
mode
0.5 W or less (19 W when Quick Start is ON)
Standby power consumption*
131.2 × 83.9 × 34.4 cm
131.2 × 80.6 × 5.7 cm
43.0 kg
115.6 × 74.2 × 25.5 cm
102.4 × 66.8 × 25.5 cm
102.4 × 63.5 × 5.7 cm
24.0 kg
Dimensions
(Approx.)
(w × h × d)
with Table-Top
Stand
115.6 × 70.9 × 5.7 cm
26.0 kg
without Table-Top
Stand
Mass(Approx.) with Table-Top
Stand
33.0 kg
19.0 kg
17.0 kg
without Table-Top
Stand
SU-WL500/SU-WL700 Wall-Mount Bracket
Supplied accessories
Optional accessories
* Specified standby power is reached after the unit finishes necessary internal processes.
Wireless system
OFDM
Transmission system
Carrier frequency
5.15 to 5.25 GHz
30 cm to 20 m (depending on installation / usage)
Transmission distance
GB
(Continued)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Input Signal Reference Chart for
PC
Resolution
Signals
Horizontal
(Pixel)
×
Vertical (Line) Horizontal
Vertical
Standard
VGA
frequency (kHz) frequency (Hz)
VGA
640
640
×
480
480
400
600
600
768
768
768
768
768
768
768
1024
31.5
37.5
31.5
37.9
46.9
48.4
56.5
60.0
47.4
47.8
60.3
47.7
64.0
60
75
70
60
75
60
70
75
60
60
75
60
60
×
×
×
×
×
×
×
×
×
×
×
×
VESA
VGA-T
720
SVGA
XGA
800
VESA Guidelines
VESA
800
1024
1024
1024
1280
1280
1280
1360
1280
VESA Guidelines
VESA
VESA
WXGA
SXGA
VESA
VESA
VESA
VESA
• This unit’s PC input does not support Sync on Green or Composite Sync.
• This unit’s PC input does not support interlaced signals.
• This unit’s PC input supports signals in the above chart with a 60 Hz vertical frequency. For other signals,
you will see the message “No signal.”
PC Input Signal Reference Chart for HDMI IN 1, 2, 3
Resolution
Signals
Horizontal
(Pixel)
×
Vertical (Line) Horizontal
Vertical
Standard
VGA
frequency (kHz) frequency (Hz)
VGA
640
800
×
480
600
768
768
768
1024
31.5
37.9
48.4
47.4
47.8
64.0
60
60
60
60
60
60
SVGA
XGA
×
×
×
×
×
VESA Guidelines
VESA Guidelines
VESA
1024
1280
1280
1280
WXGA
WXGA
SXGA
VESA
VESA
GB
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check whether the 1 (standby) indicator is flashing in red.
When it is flashing
The self-diagnosis function is activated.
1
Count how many 1 (standby) indicator flashes between each two second break.
For example, the indicator flashes three times, then there is a two second break, followed by
another three flashes, etc.
2
Press 1 on the unit to turn it off, disconnect the mains lead, and inform your dealer or Sony
service centre of how the indicator flashes (number of flashes).
When it is not flashing
1
2
Check the items in the tables below.
If the problem still persists, have your unit serviced by qualified service personnel.
Condition
Explanation/Solution
Picture
No picture (screen is dark) and • Check the aerial/cable connection.
no sound
• Connect the unit to the mains, and press 1 on the unit.
• If the 1 (standby) indicator lights up in red, press TV "/1.
• Press to display the connected equipment list, then select the
desired input.
No picture or no menu
information from equipment
connected to the scart
connector
/
• Check the connection between the optional equipment and the unit.
Double images or ghosting
(only in analogue mode)
• Check the aerial/cable connection.
• Check the aerial location and direction.
Only snow and noise appear • Check if the aerial is broken or bent.
on the screen (only in
analogue mode)
• Check if the aerial has reached the end of its serviceable life (three to
five years in normal use, one to two years at the seaside).
Picture or sound noise when • Adjust “AFT” (Automatic Fine Tuning) to obtain better picture
analogue mode)
Some tiny black points and/or • The picture of a display unit is composed of pixels. Tiny black points
bright points appear on the
screen
and/or bright points (pixels) on the screen do not indicate a malfunction.
No colour on programmes
No colour or irregular colour • Check the connection of the
/
COMPONENT IN sockets and
when viewing a signal from
the COMPONENT
IN sockets
check if each sockets are firmly seated in their respective sockets.
/
Picture freezes or contains
blocks on the screen
(low signal), check the aerial/cable connection.
• Remove the connected USB device. It can be damaged or not supported
by the unit.
Check the website below for updated information about compatible USB
devices:
Sound
No sound, but good picture
• Press 2 +/– or % (Mute).
• Check if the “Speaker” is set to “TV Speaker” (page 32).
• When using HDMI input with Super Audio CD or DVD-Audio,
DIGITAL AUDIO OUT (OPTICAL) may not output audio signals.
GB
(Continued)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Condition
Explanation/Solution
Channels
The desired channel cannot be • Switch between digital and analogue mode and select the desired digital/
selected
analogue channel.
Some channels are blank
• Scrambled/Subscription only channel. Subscribe to the pay TV service.
• Channel is used only for data (no picture or sound).
• Contact the broadcaster for transmission details.
Digital channels are not
displayed
• Contact a local installer to find out if digital transmissions are provided
in your area.
• Upgrade to a higher gain aerial.
Wireless communication
Delay pictures
• Wireless communication takes time to establish after turning the power
on. About 20 seconds are needed to display pictures. Selecting “Quick
“Wireless communication in • When the wireless communication is disturbed, it takes about 15 seconds
progress.” does not disappear, to display pictures again. “Wireless communication in progress.” is
or “Wireless communication
failed.” is displayed
displayed until pictures come back.
Check the installation situation of the monitor and media receiver (page 4).
•
• Check whether wireless equipment using the same radio frequency as
this unit is working near by, or something disturbing wireless
communication of this unit is close to the unit. In such cases, keep such
equipment away from the unit or turn off the power of that equipment.
Noisy or interrupted picture or • Check the installation situation of the monitor and media receiver (page 4).
sound
• Pictures may be distorted if somebody walks across between the monitor
and media receiver.
• Check whether wireless equipment using the same radio frequency as
this unit is working near by, or something disturbing wireless
communication of this unit is close to the unit. In such cases, keep such
equipment away from the unit or turn off the power of that equipment.
General
Distorted picture and/or sound • Keep the unit away from electrical noise sources such as cars,
motorcycles, hair-dryers or optical equipment.
• When installing optional equipment, leave some space between the
optional equipment and the unit.
• Check the aerial/cable connection.
• Keep the aerial/cable TV cable away from other connecting cables.
The unit turns off
automatically (the unit enters
standby mode)
• Check if the “Sleep Timer” is activated, or confirm the “Duration”
setting of “On Timer Settings” (page 30).
• If no signal is received and no operation is performed in the TV mode
for 10 minutes, the monitor automatically switches to standby mode.
The unit turns on
automatically
• Check if the “On Timer” is activated (page 30).
selected
The remote does not function • Replace the batteries.
A channel cannot be added to • Up to 999 channels can be stored in the Favourite list.
the Favourite list
HDMI equipment does not
• Check that your equipment is “Control for HDMI” compatible
appear on “HDMI Device List” equipment.
Not all channels are tuned
• Check support web site for cable provide information.
You cannot select “Off” in
“Control for HDMI”
• If any “Control for HDMI” compatible audio equipment is connected to
the unit, you cannot select “Off” in this menu. If you want to change the
audio output to the monitor speaker, select “TV Speaker” in the
“Speaker” menu (page 32).
message appears on the screen
GB
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|