3-070-514-11(1)
SACD/DVD
Player
Operating Instructions
DVP-NC650V
ã 2001 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
Precautions
On safety
• Caution – The use of optical instruments
with this product will increase eye hazard.
• Should any solid object or liquid fall into
the cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
On power sources
• The player is not disconnected from the AC
power source as long as it is connected to
the wall outlet, even if the player itself has
been turned off.
On cleaning discs
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord, grasp the plug itself; never pull
the cord.
• Should the AC power cord need to be
changed, have it done at a qualified service
shop only.
Do not use a commercially available cleaning
disc. It may cause a malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display
image on your television screen
indefinitely. If you leave the still video
image or on-screen display image displayed
on your TV for an extended period of time
you risk permanent damage to your
television screen. Projection televisions are
especially susceptible to this.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug.
On transporting the player
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
Before transporting the player, follow the
procedure below to return the internal
mechanisms to their original positions.
1 Remove all the discs from the disc tray.
2 Press A to close the disc tray.
Make sure that “NO DISC’ appears on
the front panel display.
On operation
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
3 Wait for 10 seconds, then press ?/1 on
the remote, followed by POWER on the
player.
This will safely turn off the player.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Welcome! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
This Player Can Play the Following Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Notes about the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Index to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Guide to the Control Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Quick Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 2: Inserting Batteries into the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 3: TV Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Step 4: Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 1: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 2: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Step 3: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Step 4: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Resuming Playback from the Point Where You Stopped the Disc
(Resume Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Using the DVD’s Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Selecting “ORIGINAL” or “PLAY LIST” on a DVD-RW Disc . . . . . . . . . . . . . .37
Selecting a Playback Area for an SACD Disc . . . . . . . . . . . . . . . . . . . . . . . . .38
Playing VIDEO CDs with PBC Functions (PBC Playback) . . . . . . . . . . . . . . .39
Various Play Mode Functions (Program Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Searching for a Particular Point on a Disc (Search, Scan, Slow-motion Play,
Freeze Frame). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Searching for a Disc/Title/Chapter/Track/Index/Scene (Search mode) . . . . .48
Searching by Scene (VIEWER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Information About the Disc . . . . . . . . . . . . . . . . . . . . . . 52
Viewing the Playing Time and Remaining Time on the Front Panel Display. . 52
Checking the Playing Time and Remaining Time . . . . . . . . . . . . . . . . . . . . . . 53
Checking the Play Information (ADVANCED) . . . . . . . . . . . . . . . . . . . . . . . . 55
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
SURROUND Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Enjoying Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Changing the Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Displaying the Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Adjusting the Picture Quality (BNR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Adjusting the Playback Picture (VIDEO EQUALIZER) . . . . . . . . . . . . . . . . . . 66
Enhancing the Playback Picture (DIGITAL VIDEO ENHANCER) . . . . . . . . . 67
Using Various Additional Functions . . . . . . . . . . . . . . . . . . . . . . 68
Locking Discs (Custom Parental Control, Parental Control) . . . . . . . . . . . . . . 68
Operation Sound Effects (Sound Feedback) . . . . . . . . . . . . . . . . . . . . . . . . . 72
Controlling Your TV or AV Amplifier (Receiver) with the Supplied Remote . . 73
Controlling a CD Changer (Mega Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Using the Setup Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . . . 78
Settings for the Display (SCREEN SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Custom Settings (CUSTOM SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Settings for the Speakers (SPEAKER SETUP) . . . . . . . . . . . . . . . . . . . . . . . 86
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Self-diagnosis Function (When letters/numbers appear in the display) . . . . . 91
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
List of Setup Display Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CD
Music CD
About this Manual
• Instructions in this manual describe the
controls on the remote. You can also use the
controls on the player if they have the same
or similar names as those on the remote.
• The icons used in this manual are described
below:
“DVD VIDEO” and “DVD-RW” are trademarks.
z
Icon
Meaning
Region code
Functions available for DVD
VIDEOs or DVD-Rs/DVD-
RWs in Video mode
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEO discs (playback only) labeled with
identical region codes.
Functions available for DVD-
RWs in VR (Video Recording)
mode
ALL
DVDs labeled
player.
will also play on this
Functions available for VIDEO
CDs or CD-Rs/CD-RWs
If you try to play any other DVD, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD, no region code
indication may be labeled even though
playing the DVD is prohibited by area
restrictions.
Functions available for Super
Audio CDs
Functions available for music
CDs or CD-Rs/CD-RWs
z
More convenient features
* “DVD” may be used as a general term for DVD
VIDEOs, DVD-Rs, and DVD-RWS.
X
Region code
MODEL NO.
DVP–XXXX
CD/DVD PLAYER
AC 00V 00Hz
NO.
00W
SONY CORPORATION
MADE IN JAPAN
0-000-000-00
This Player Can Play the
Following Discs
Example of discs that the player
cannot play
The player cannot play the following discs:
• CD-ROMs (PHOTO CDs included)
• All CD-Rs/CD-RWs other than music and
VCD format CD-Rs/CD-RWs
• Data part of CD-Extras
Format of discs
DVD VIDEO
• DVD-ROMs
• DVD Audio discs
DVD-RW
SACD
Also, the player cannot play the following
discs:
• A DVD with a different region code (page
93).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• A disc recorded in a color system other than
NTSC, such as PAL or SECAM. (This
player conforms to the NTSC color
system.)
• A disc that has a non-standard shape (e.g.,
card, heart).
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
edge. Do not touch the surface.
Note
Some DVD-Rs, DVD-RWs, CD-Rs or CD-RWs
cannot be played on this player due to the recording
quality or physical condition of the disc, or the
characteristics of the recording device. DVD-RWs in
VR mode may also take time to play back due to the
recording condition.
Furthermore, the disc will not play if it has not been
correctly finalized. For more information, see the
operating instructions for the recording device.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave
it in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
On cleaning
Note on playback operations of DVDs
and VIDEO CDs
• Before playing, clean the disc with a
cleaning cloth. Wipe the disc from the
center out.
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
• Do not use solvents such as benzine,
thinner, commercially available cleaners, or
anti-static spray intended for vinyl LPs.
Copyrights
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents, other
intellectual property rights owned by
Macrovision Corporation, and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only,
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front Panel (shown with the front door open)
A BNR (Block Noise Reduction) button/
indicator (65)
U MULTI CHANNEL (multi-channel)
indicator
B SURROUND button/indicator (58)
C POWER (power) switch/indicator (33)
D DISC SELECT (disc select) 1 through 5
buttons (34)
Lights up when:
–playing a disc that contains multiple
audio signal channels
–the disc is not inserted
E
(remote sensor) (15)
V DVD indicator
F Front panel display (9)
G Disc tray (33)
H H (play) button (33)
I X (pause) button (34, 72)
J x (stop) button (33)
K ./> (previous/next) buttons (34)
L A (open/close) button (34)
M C/X/x/c/ENTER (enter) buttons (28)
N PHONES (phones) jack (33)
O LEVEL (level) control (33)
P SHUFFLE (shuffle) button (43)
Q REPEAT (repeat) button (44)
R ONE/ALL (one/all) button (40)
S LOAD (load) button (34)
T SACD indicator
Lights up when the disc is a DVD.
W TOP MENU (top menu) button (37)
X MENU (menu) button (37)
Y ORETURN (return) button (39)
Z MEGA CONTROL (mega control)
button/indicator (75)
wj EXCHANGE (exchange) button (35)
wk DISC SKIP (disc skip) button (33)
wl DISPLAY (display) button (12)
Lights up when the disc is an SACD.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Display
When playing back a DVD VIDEO/DVD-RW
Playing status
Current chapter (52)
Lights up when you can change
the angle
All Discs mode (40)
Current disc (52)
Disc type
Current audio
signal (57)
Current title (52)
Playing time (52)
Current play mode (40)
When playing back a VIDEO CD (PBC)
Playing status
All Discs mode (40)
Disc type
Playing time (52)
Current scene (52)
Current disc (52)
Current play mode (40)
When playing back an SACD, CD or VIDEO CD (without PBC)
Playing status
Playing time (52)
All Discs mode (40)
Current track (52)
Disc type*
Current disc (52)
Current play mode (40)
Current index (52)
Lights up when playing the multi-channel playback area on SACDs (38)
* When playing the SACD layer of SACD discs, the disc type is not displayed.
continued
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
A DIGITAL OUT (COAXIAL) (digital out
(coaxial)) jack (22, 24, 26)
B DIGITAL OUT (OPTICAL) (digital out
(optical)) jack (22, 24, 26)
C 5.1CH OUTPUT (5.1-channel output)
jack (22)
D AUDIO IN L/R (audio in left/right) jacks
(75)
E LINE OUT L/R (AUDIO) (line out left/
right (audio)) 1/2 jacks (16, 21, 24, 26)
F LINE OUT (VIDEO) (line out (video)) 1/
2 jacks (16, 18)
G S VIDEO OUT (S video out) 1/2 jacks
(18)
H COMPONENT VIDEO OUT
(component video out) jacks (18)
I MEGA CONTROL (mega control) jack
(75)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
A TV/DVD switch (73)
B Z OPEN/CLOSE (open/close) button
(33)
Remote
1
2
3
C Number buttons (37)
qh
The number 5 button has a tactile dot.
D CLEAR (clear) button (41, 43, 44, 45)
E SACD MULTI/2CH (SACD multi/2-
channel) button (38)
qj
qk
ql
w;
wa
ws
wd
wf
wg
wh
wj
wk
wl
e;
ea
es
ed
1
4
7
2
3
6
9
5
8
0
F SACD/CD button (38)
4
5
6
7
8
G AUDIO (audio) button (56)
H ANGLE (angle) button (63)
I SHUFFLE (shuffle) button (43)
J PROGRAM (program) button (41)
K ./> PREV/NEXT (previous/
next) buttons (34)
9
q;
qa
qs
qd
L
/
SEARCH/STEP (search/
step) buttons (47)
M H PLAY (play) button (33)
The H button has a tactile dot.
N TOP MENU (top menu) button (37)
O DISPLAY (display) button (12)
P ?/1 (on/standby) button (33)
Q VOL (volume) +/– buttons (73)
The + button has a tactile dot.
qf
qg
ef
eg
R TV/VIDEO/BNR (TV/video/BNR)
button (65, 73)
S WIDE MODE (wide mode)/DVE
(Digital Video Enhancer) button (67, 73)
T ENTER (enter) button (28)
U DISC SKIP (disc skip) button (34)
V SEARCH MODE (search mode) button
(48)
W TIME/TEXT (time/text) button (52)
X SUBTITLE (subtitle) button (64)
Y A-B button (45)
Z REPEAT (repeat) button (44)
wj REPLAY (replay) button (34)
wk SURROUND (surround) button (58)
wl
/
SCAN/SLOW buttons (47)
e; x STOP (stop) button (34)
ea X PAUSE (pause) button (34)
es MENU (menu) button (37)
ed C/X/x/c buttons (28)
ef ORETURN (return) button (39)
eg ENTER (enter) button (28)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
Use the Control Menu to select a function that you would like to use. The Control Menu display
appears when the DISPLAY button is pressed. For details, please refer to the page in parentheses.
Control Menu
Currently playing disc
number
Total number of titles or tracks
recorded
Currently playing title
number (VIDEO CD/SACD/
CD: track number)
Total number of
chapters or indexes
recorded
Playback status
(N Playback, X
Pause, xStop, etc.)
Currently playing chapter
number (VIDEO CD/SACD/
CD: index number)
1
PLAY
DVD VIDEO
Type of disc
being played
back
(
(
)
)
1 2 2 7
1 8 3 4
T
Playing time
1 : 3 2 : 5 5
Current
setting
Icon of selected Control
Menu item
OFF
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
Control Menu items
Options
Function name of selected
Control Menu item
SUBTITLE
Select:
ENTER
RETURN
Cancel:
Operation message
List of Control Menu Items
DISC (page 48)
Selects the disc to be played.
TITLE (page 48)/SCENE (page 48)/
TRACK (page 48)
Selects the title, scene, or track to be played.
Selects the chapter or index to be played.
CHAPTER (page 48)/INDEX (page
48)
TRACK (page 48)
Selects the track to be played.
Selects the index to be played.
INDEX (page 48)
TIME/TEXT (page 48)
Checks the elapsed time and the remaining
playback time.
Input the time code for picture and music
searching.
Displays the DVD or SACD/CD text.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ORIGINAL/PLAY LIST (page 37)
Selects the type of titles (DVD-RW) to be
played, the ORIGINAL one, or an edited PLAY
LIST.
AUDIO (page 56)
Changes the audio setting.
MULTI/2CH (page 38)
Selects the playback area on SACDs when
available.
SUBTITLE (page 64)
Displays the subtitles.
Changes the subtitle language.
ANGLE (page 63)
Changes the angle.
SURROUND (page 58)
ADVANCED (page 55)
Selects the surround functions.
Checks the information (bit rate or layer) on
the disc while playing a DVD.
PARENTAL CONTROL (page 68)
SETUP (page 77)
Set to prohibit playback on this player.
QUICK Setup (page 28)
Use Quick Setup to choose the desired
language for the on-screen display, the aspect
ratio of the TV, the audio output, and the
appropriate speaker settings.
CUSTOM Setup
In addition to the Quick Setup setting, you can
adjust other various settings.
RESET
Returns the settings in “SETUP” to the default
setting.
ONE/ALL DISCS (page
40)
Selects One Disc or All Discs mode.
PROGRAM (page 41)
SHUFFLE (page 43)
REPEAT (page 44)
Selects the discs, title, chapter, or track to play
in the order you want.
Plays the discs, title, chapter, or track in a
random order.
Plays the discs, entire disc (all titles/all tracks),
or one title/chapter/track repeatedly.
A-B REPEAT (page 45)
BNR (page 65)
Specifies the parts you want to play repeatedly.
Adjusts the picture quality by reducing the
“block noise” or mosaic like patterns that
appear on your TV screen.
VIDEO EQUALIZER (page 66)
Adjusts the video signal from the player. You
can select the picture quality that best suits the
program you are watching.
DIGITAL VIDEO ENHANCER (page
67)
Exaggerates the outline of the image to
produce a sharper picture.
continued
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VIEWER (page 50)
Divides the screen into 9 sub-screens to help
you find the scene you want quickly.
z Each time you press DISPLAY, the Control Menu display changes as follows:
, Control Menu display 1
m
Control Menu display 2
m
ADVANCED display (Appears if you select any setting other than “OFF.” See page 55.)
m
Control Menu display off
t
z The Control Menu icon indicator lights up in green
when you select any item except
“OFF” (“SURROUND,” “PROGRAM,” “SHUFFLE,” “REPEAT,” “A-B REPEAT,” “BNR,” “DIGITAL VIDEO
ENHANCER” only). The “ANGLE” indicator lights up in green only when the angles can be changed. The “VIDEO
EQUALIZER” indicator lights up in green when any setting other than “STANDARD” is selected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Quick Overview
A quick overview presented in this chapter will give you enough information to start using the
player for your enjoyment. To use the surround sound features of this player, refer to “Hookups”
on page 18.
Notes
• You cannot connect this player to a TV that does not have a video input jack.
• Be sure to turn off the power of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (pinplug x 3 y pinplug x 3) (1)
• Remote commander (remote) RMT-D133A (1)
• Size AA (R6) batteries (2)
• S VIDEO cord (1)
Step 2: Inserting Batteries into the Remote
You can control the player using the supplied remote. Insert two size AA (R6) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When using
the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from
battery leakage and corrosion.
continued
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: TV Hookups
Connect the supplied audio/video cord and power cord in the order (1~3) shown below. Be
sure to connect the power cord last.
to video input
1 Audio/video cord
(yellow)
(supplied)
(yellow)
(white)
(white)
to LINE OUT L/R
(AUDIO) 1
(red)
(white)
(red)
to LINE OUT
to audio input
(VIDEO) 1
TV
(yellow)
(red)
2 Power source
SACD/DVD Player
3 Power source
l: Signal flow
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen.
If you want to change the aspect ratio, please refer to page 79.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Playing a Disc
A Turn on the TV.
B Switch the input selector on the TV to the player.
Disc compartment number
With the playback side facing down
C Press POWER on the player.
D Press A on the player to open the disc tray.
E Place the disc on the tray with the playback side facing down.
F Press H.
The disc tray closes and the player begins playing the disc.
After Step 6
Depending on the disc, a menu may be displayed on the TV screen. If so, select the item you want
from the menu and play the DVD (page 37) or VIDEO CD disc (page 39).
To stop playing
Press x.
To take out the disc
Press A.
To turn off the player
Press ?/1 on the remote. The player is set to standby mode and the power indicator lights up in
red. Press POWER on the player to turn off completely.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Hookups
Hooking Up the Player
Follow Steps 1 to 4 to hook up and adjust the settings of the player.
Before you start, turn off the power, check that you have all of the supplied accessories, and insert
the batteries into the remote (page 15).
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
Step 1: Connecting the Video Cords
Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through C, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
Audio/video cord
(supplied)
(yellow)
TV, projector, AV
amplifier (receiver)
(yellow)
SACD/DVD player
(green)
(red)
(green)
(blue)
(blue)
(red)
S VIDEO cord
(supplied)
Component video
cord (not supplied)
TV, projector, AV
amplifier (receiver)
TV, projector, AV
amplifier (receiver)
l: Signal flow
18
Download from Www.Somanuals.com. All Manuals Search And Download.
A If you are connecting to a video input jack
Connect the yellow plugs of the audio/video cord (supplied) to the yellow (video) jacks. You will
enjoy standard quality images.
Yellow
Yellow (Video)
White (L)
White (L)
Red (R)
Red (R)
Use the red and white plugs to connect to the audio input jacks (page 21).
B If you are connecting to an S VIDEO input jack
Connect the S VIDEO cord (supplied). You will enjoy high quality images.
B If you are connecting to a monitor, projector, or AV amplifier (receiver) having
component video input jacks (Y, PB, PR)
Connect the component via the COMPONENT VIDEO OUT jacks using the component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy
accurate color reproduction and high quality images.
Green
Blue
Red
Green
Blue
Red
Note
Do not connect your player to a VCR. You may not receive a clear image on the TV screen if you pass the player
signals via the VCR.
VCR
SACD/DVD player
TV
Connect directly.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connecting the Audio Cords
Refer to the chart below to select the connection that best suits your system. The surround effects
you will enjoy depend on the connections and components you use.
Select a connection
D
Select one of the following connections,
A
through
.
Connection
Components to be connected
TV (stereo)
A
B
(page 21)
AV amplifier (receiver) having 5.1ch input jacks
• 4 speakers
(page 22)
(front L and R, rear L and R)
• 6 speakers
(front L and R, center, rear L and R, subwoofer)
AV amplifier (receiver) having a Dolby* Digital or DTS** decoder,
and a digital input jack
• 6 speakers
(page 22)
(page 24)
B
C
(front L and R, center, rear L and R, subwoofer)
Stereo amplifier (receiver)
(having L and R audio input jacks only, or having a digital input jack)
• 2 speakers
(front L and R)
MD deck/DAT deck
(page 24)
(page 26)
C
D
AV amplifier (receiver) with a Dolby Surround (Pro Logic) decoder
(having L and R audio input jacks only, or having a digital input jack)
• 3 speakers
(front L and R, and rear (monaural))
• 6 speakers
(front L and R, center, rear L and R, subwoofer)
z To enjoy SACD Multi or 96 kHz/24 bit sound, use connection
.
B
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are
trademarks of Dolby Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories. All rights
reserved.
**Manufactured under license from Digital Theater Systems, Inc. US PAT. No. 5,451,942 and other world-wide
patents issues and pending. “DTS” and “DTS Digital surround” are trademarks of Digital Theater Systems, Inc.
© 1996 Digital Theater Systems, Inc. All rights reserved.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Connecting to your TV
This connection will use your TV speakers for sound.
xRecommended surround sound effects for this connection
• TVS DYNAMIC (page 58)
• TVS WIDE (page 58)
SACD/DVD player
TV
(yellow)
(yellow)
(white)
(white)
Audio/video
cord
(supplied)
(red)
(red)
to audio input
l: Signal flow
The yellow plug is used for video signals (page 18).
continued
Download from Www.Somanuals.com. All Manuals Search And Download.
21
B
Connecting to an AV amplifier (having 5.1ch input jacks or a digital input
jack) and 4 to 6 speakers
B-1
If your AV amplifier (receiver) has 5.1 channel inputs, use
.
If you want to use the Dolby Digital or DTS decoder function on your AV amplifier (receiver),
B-2
connect to its digital jack using
. With the following connections, you can enjoy a more
realistic audio presence in the comfort of your own home.
B-1
: Connecting to the 5.1ch input jacks
You can enjoy 5.1ch surround sound using the internal Dolby Digital, DTS or SACD Multi
decoder of this player. You can also enjoy Dolby Surround (Pro Logic) sounds, or surround
sounds using various “SURROUND” modes (page 58).
xRecommended surround sound effects for this connection
When 6 speakers are connected (Set “SURROUND” to “OFF.”)
• Dolby Digital (5.1ch) (page 92)
• DTS (5.1ch) (page 92)
• SACD Multi-channel (page 93)
B-2
: Connecting to a digital jack
This connection will allow you to use the Dolby Digital or DTS decoder function of your AV
amplifier (receiver). You are not able to enjoy the surround sound effects of the player.
xRecommended surround sound effects using this connection with your amplifier (receiver)
• Dolby Digital (5.1ch) (page 92)
• DTS (5.1ch) (page 92)
• 96 kHz/24 bit PCM
z Refer to the operating instructions of the AV amplifier (receiver) for correct speaker setting location when using
B-2
the
connection.
Notes
• After you have completed the connection, be sure to set “DOLBY DIGITAL” to “DOLBY DIGITAL” (page 84)
and “DTS” to “DTS” (page 85). Otherwise, no sound or a loud noise will come from the speakers.
• When you connect an amplifier (receiver) that conforms to the 96 kHz sampling frequency, set “48kHz/96kHz
PCM” to “96kHz/24bit” (page 85).
• SACD audio signals are not output from a digital jack.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SACD/DVD player
Optical digital cord
(not supplied)
Remove jack cap
before connecting.
Stereo audio cord
(not supplied)
or
or
Coaxial digital cord
(not supplied)
Monaural audio cord
(not supplied)
to coaxial or optical
digital input
to audio input
[Speakers]
[Speakers]
AV amplifier (receiver) having
5.1ch inputs or/and a decoder
Front (L)
Subwoofer
Front (R)
Center
Rear (L)
Rear (R)
l: Signal flow
z To enhance the surround sound effects:
• Use high-performance speakers.
• Use front, rear, and center speakers having the same size and performance.
• Place a subwoofer between the right and left front speakers.
•
continued
23
Download from Www.Somanuals.com. All Manuals Search And Download.
C
Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to an
MD deck or DAT deck
This connection will use your 2 front speakers connected to your stereo amplifier (receiver) for
C-1
sound. If the stereo amplifier (receiver) has audio input jacks L and R only, use
amplifier (receiver) has a digital input jack, use
. If the
C-2
. When connecting to an MD deck or a DAT
C-2
deck, use
. In this case, you can also connect the player directly to the MD deck or DAT
deck without using your stereo amplifier (receiver).
C-1
xRecommended surround sound effects for the
connection only
• TVS STANDARD (page 58)
z In connection
, you can use the supplied audio/video cord instead of using a separate audio cord.
C-1
z To realize better surround sound effects, make sure that your listening position is in between your speakers.
Note
SACD audio signals are not output from a digital jack.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SACD/DVD player
Coaxial digital cord
(not supplied)
Stereo audio cord
(not supplied)
(red)
(white)
or
or
Optical digital cord
(not supplied)
Remove the jack
cap before
(red)
(white)
connecting.
to coaxial or optical
digital input
to audio input
[Speakers]
Front (L)
Stereo amplifier (receiver)
MD deck/DAT deck
Front (R)
l: Signal flow
continued
Download from Www.Somanuals.com. All Manuals Search And Download.
25
D
Connecting to a Dolby Surround (Pro Logic) decoder amplifier (receiver) and
3 to 6 speakers
This connection will allow you to enjoy the surround effects of the Dolby Surround (Pro Logic)
decoder on your amplifier (receiver). If you have an AV amplifier (receiver) equipped with a
Dolby Digital or DTS decoder, refer to page 22.
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or
multichannel audio (Dolby Digital) discs.
This connection needs a minimum of 3 speakers (front L and R, and rear (monaural)). The
surround effects are enhanced if 6 speakers (front L and R, center, rear L and R, and subwoofer)
are used.
D-1
If your amplifier (receiver) has R and L audio input jacks only, use
. If your amplifier
D-2
(receiver) has a digital input jack, use
.
xRecommended surround sound effects using this connection with your amplifier (receiver)
• Dolby Surround (Pro Logic) (page 92)
z For correct speaker setting location, please refer to the operating instructions of the amplifier (receiver).
Note
SACD audio signals are not output from a digital jack.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SACD/DVD player
Coaxial digital cord
(not supplied)
Stereo audio cord
(not supplied)
(red)
(white)
or
or
Optical digital cord
(not supplied)
Remove the jack cap
before connecting.
(white)
(red)
to coaxial or optical
digital input
to audio input
[Speakers]
[Speakers]
Amplifier (receiver) with
Dolby Surround decoder
Front (R)
Rear (L)
Front (L)
Rear (R)
Rear*
(mono)
Subwoofer
Center
l: Signal flow
* When connecting 6 speakers, replace the monaural rear speaker with a center speaker, 2 rear speakers and a
subwoofer.
Step 3: Connecting the Power Cord
Plug the player and TV power cords into an AC outlet.
Do not connect the power cord of your player to the “switched” power socket of an amplifier
(receiver). Otherwise, when you turn off the power of your amplifier (receiver), the settings for
the player may be lost.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Quick Setup
Follow the steps below to make the minimum number of basic adjustments to use the player. To
skip an adjustment press >, to return to the previous adjustment, press ..
?/1
1
4
7
2
3
6
9
5
8
0
./>
POWER
./>
X/x
X/x, ENTER
ENTER
A Turn on the TV.
B Switch the input selector on the TV to the player.
C Press POWER on the player and press ?/1 on the remote.
“Press [ENTER] to run QUICK SETUP.” appears at the bottom of the screen. If this message
does not appear, select “QUICK” under “SETUP” in the Control Menu (page 77) to run Quick
Setup.
D Press ENTER without inserting a disc.
The Setup Display for selecting the language used in the on-screen display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
E Press X/x to select a language.
The player uses the language selected here to display the menu and subtitles as well.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
F Press ENTER.
The Setup Display for selecting the aspect ratio of the TV to be connected appears.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
G Press X/x to select the item.
TV Type
You select
Page
4:3 standard TV
4:3 LETTER BOX or 4:3
PAN SCAN
79
A wide-screen TV or 4:3 standard TV with the 16:9
wide-screen mode
79
H Press ENTER.
The Setup Display for selecting the type of jack used to connect your amplifier (receiver)
appears.
Is this player connected to an amplifier
(receiver)? Select the type of jack you
are using.
YES
LINE OUTPUT L/R(AUDIO)
DIGITAL OUTPUT
DIGITAL & 5.1CH OUTPUT
NO
I Press X/x to select the item, then press ENTER.
Audio Cord Connecting Type
You select
LINE OUTPUT L/R (AUDIO)
C-1
B-2
B-1
A
D-1
C-2
DIGITAL OUTPUT
DIGITAL & 5.1CH OUTPUT
NO
D-2
B-1
B-2
or both
and
• When “NO” or “LINE OUTPUT L/R (AUDIO)” is selected, Quick Setup is finished and
connections are complete.
• When “DIGITAL OUTPUT” or “DIGITAL & 5.1CH OUTPUT” is selected, the Setup
Display for “DOLBY DIGITAL” appears.
continued
29
Download from Www.Somanuals.com. All Manuals Search And Download.
J Press X/x to select the item.
B
Choose the item that matches the audio connection you selected in pages 22 to 26 (
D
through
).
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
OFF
STANDARD
SHARP
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
ON
D-PCM
D-PCM
48kHz/96kHz PCM:
DOLBY DIGITAL
Audio Cord Connection Type
You select
Page
D-PCM
83
C-2
B-2
D-2
DOLBY DIGITAL (only if the
amplifier/receiver has a Dolby Digital
decoder)
83
K Press ENTER.
“DTS” is selected.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
OFF
STANDARD
SHARP
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
ON
D-PCM
D-PCM
D-PCM
48kHz/96kHz PCM:
DTS
L Press X/x to select the item.
B
Choose the item that matches the audio connection you selected in pages 22 to 26 (
D
through
).
Audio Cord Connection Type
You select
Page
D-PCM
83
C-2
B-2
D-2
DTS (only if the amplifier/receiver
has a DTS decoder)
83
M Press ENTER.
• When “DIGITAL OUTPUT” is selected in Step 8, Quick Setup is finished. All
connections and setup operations are complete.
• When “DIGITAL & 5.1CH OUTPUT” is selected in Step 8, the Setup display for
“SPEAKER SETUP” appears.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
N Press X/x to select the size of the center speaker.
If no center speaker is connected, select “NONE.” Refer to page 86 for each selection item.
SPEAKER SETUP
SIZE:
DISTANCE:
BALANCE:
LEVEL:
TEST TONE:
FRONT:
OFF
LARGE
NONE
NONE
LARGE
SMALL
CENTER:
REAR:
SUBWOOFER:
O Press ENTER.
The Setup Display for selecting the size of the rear speaker appears.
SPEAKER SETUP
SIZE:
DISTANCE:
BALANCE:
LEVEL:
TEST TONE:
FRONT:
OFF
LARGE
LARGE
NONE
CENTER:
REAR:
SUBWOOFER:
NONE
LARGE(REAR)
P Press X/x to select the size.
If no rear speaker is connected, select “NONE.”
“SIDE” and “REAR” refer to the speakers’ position relative to your listening position.
Refer to page 86 for each selection item.
Q Press ENTER.
The Setup Display for selecting whether or not you have connected a subwoofer appears.
SPEAKER SETUP
SIZE:
DISTANCE:
BALANCE:
LEVEL:
TEST TONE:
FRONT:
OFF
LARGE
LARGE
LARGE(REAR)
NONE
CENTER:
REAR:
SUBWOOFER:
NONE
YES
ENTER
To set, press
To quit, press
, then
.
DISPLAY
. .
R Press X/x to select the item.
S Press ENTER.
Quick Setup is finished. All connections and setup operations are complete.
continued
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
You can directly start Quick Setup only when you run it for the first time.
To run Quick Setup a second time, select “QUICK” under “SETUP” in the Control Menu (page 77).
Enjoying the surround sound effects
To enjoy the surround sound effects of this player or your amplifier (receiver), the following
items must be set as described below for the audio connection you selected in pages 22 to 26
B
(
through
). Each of these are the default settings and do not need to be adjusted when
D
you first connect the player. Refer to page 77 for using the Setup Display.
Audio Connection (pages 21 to 26)
A
No additional settings are needed.
B-1
Item
You select
Page
DISTANCE
BALANCE
LEVEL
Set according to the connected
speakers
86
• If the sound distorts even when the volume is turned down, set “AUDIO ATT” to “ON” (page
83).
B-2
C-2
D-2
Item
You select
DOLBY SURROUND
ON
Page
84
DOWNMIX
DIGITAL OUT
84
• Set “48kHz/96kHz PCM” to “96kHz/24bit,” only if you connect an amplifier (receiver) that
conforms to 96 kHz digital audio input (page 85).
C-1
D-1
Item
You select
Page
DOWNMIX
DOLBY SURROUND
84
• If the sound distorts even when the volume is turned down, set “AUDIO ATT” to “ON” (page
83).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press A on the player, and place a
disc on the disc tray.
Playing Discs
The player automatically turns on and the
power indicator lights up in green.
To place other discs on the tray, press
DISC SKIP and place the discs in the
order you want to play them.
Playing Discs
Each time you press DISC SKIP, the disc
tray turns so you can place the discs on
the empty compartments. The player
plays from the last disc placed on the
tray.
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
POWER
Power indicator
X
x
H
Disc compartment
number
With the playback
DISC SKIP
LEVEL
side facing down
PHONES
?/1
1
4
7
2
3
6
9
5
8
0
5
Press H.
The disc tray closes, and the player starts
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
DISC
SKIP
H
x
After following Step 5
Depending on the disc, a menu may appear
on the TV screen. You can play the disc
interactively by following the instructions on
the menu. DVD VIDEO (page 37), VIDEO
CD (page 39).
1
2
Turn on your TV.
Switch the input selector on the TV
to the player.
When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel.
3
Press POWER.
The player enters standby mode and the
power indicator lights up in red.
continued
33
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn on the player
Additional operations
Press POWER on the player. The player
enters standby mode and the power indicator
lights up in red. Press ?/1on the remote. The
player turns on and the power indicator lights
up in green. In standby mode, the player also
turns on by pressing A on the player or by
pressing H.
./>
A
DISC SELECT 1 - 5
X
x
H
To turn off the player
Press ?/1 on the remote. The player enters
standby mode and the power indicator lights
up in red. To turn off the player completely,
press POWER on the player. While playing a
disc, do not turn off the player by pressing
POWER. Doing so may cancel the menu
settings. When you turn off the player, first
press x to stop playback and then press ?/1
on the remote.
open front door
DISC SKIP
LOAD
Z
1
4
7
2
3
6
9
5
8
0
DISC SKIP
REPLAY
./>
X
x
To use headphones
H
Connect headphones to the PHONES jack
and adjust the headphones volume by turning
LEVEL.
Note
To
Operation
SACD audio signals are not output from the digital
jack.
Select a disc
Press DISC SELECT 1
- 5 on the player
Stop
Press x
Pause
Press X
Resume play after
pause
Press X or H
Go to the next disc
Press DISC SKIP
Go to the next chapter,
track, or scene in
Press >
continuous play mode
Go back to the
Press .
preceding chapter,
track, or scene in
continuous play mode
Stop play and remove
the disc
Press Z
Replay a previous
scene (DVD VIDEO
only)
Press REPLAY
34
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Operation
4 Replace the discs in the compartments
Check if a disc is in the Press LOAD on the
disc compartment
with new ones.
player.
The DISC SELECT
indicator for each
compartment (1 - 5)
containing a disc lights
up.
5 Press EXCHANGE.
The disc tray closes.
z While the disc tray is open,
z The Replay function is useful when you want to
– If the playback of the current disc ends, the player
stops playing. If the disc is played in One Disc
Repeat Play mode, the current disc starts playing
again.
review a scene or dialog that you missed.
z Before loading the discs, a DISC SELECT
indicator of an empty compartment may be lit.
– In All Discs Shuffle Play mode (page 43), titles/
tracks/chapters are reshuffled only on the current
disc.
Notes
– In Program Play mode (page 41), the titles/tracks/
chapters only on the current disc are played.
• You may not be able to use the Replay function with
some scenes.
• If you turn the power off by pressing POWER on the
player, the loading information will be reset.
Note
Do not push the disc tray to close in Step 5, as you may
damage the player.
Replacing discs while playing a disc
(EXCHANGE)
You can open the disc tray while playing a
disc so that you can check which discs are to
be played next and replace discs without
interrupting playback of the current disc.
.
EXCHANGE
DISC SKIP
1 Press EXCHANGE.
The disc tray opens and two disc
compartments appear. Even if the player
is playing a disc, it doesn’t stop playing.
2 Replace the discs in the compartments
with new ones.
3 Press DISC SKIP.
The disc tray turns and another two disc
compartments appear.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Resuming Playback from
the Point Where You
Stopped the Disc (Resume
Play)
• Depending on where you stopped the disc, the player
may not resume playback from exactly the same
point.
• The point where you stopped playing is cleared
when:
– you turn the power off by pressing POWER on the
player.
– you change the play mode.
– you change the settings on the Setup Display.
– you load disc information by pressing LOAD on
the player
When you stop the disc, the player
remembers the point where you pressed x
and “RESUME” appears on the front panel
display. As long as you do not remove the
disc, Resume Play works even if the player
enters standby mode by pressing ?/1.
– you press MEGA CONTROL
H
x
1
2
Whileplaying a disc, pressx tostop
playback.
“RESUME” appears on the front panel
display and you can restart the disc from
the point where you stopped the disc.
If “RESUME” does not appear, Resume
Play is not available.
Press H.
The player starts playback from the point
where you stopped the disc in Step 1.
z To play from the beginning of the disc, press x
twice, then press H.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the DVD’s Menu
Selecting “ ORIGINAL” or
“ PLAY LIST” on a DVD-RW
Disc
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the TOP MENU button.
When you play DVDs that allow you to select
items such as the language for the subtitles
and the language for the sound, select these
items using the MENU button.
Some DVD-RW discs in VR (Video
Recording) mode have two types of titles for
playback: originally recorded titles
(ORIGINAL) and titles that can be created on
recordable DVD players for editing (PLAY
LIST). You can select the type of titles to be
played.
1
4
7
2
3
6
9
5
8
0
Number
buttons
X/x
ENTER
DISPLAY
MENU
TOP MENU
ENTER
C/X/x/c
1
2
Press DISPLAY in stop mode.
The Control Menu appears.
Press X/x to select
(ORIGINAL/PLAY LIST), then press
ENTER.
The options for “ORIGINAL/PLAY
LIST” appear.
1 Press TOP MENU or MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
1
STOP
DVD-RW
(
(
)
)
1 2 2 7
1 8 3 4
PLAY LIST
PLAY LIST
ORIGINAL
2 Press C/X/x/c or the number buttons
to select the item you want to play or
change.
3 Press ENTER.
z You can also display the disc’s menu by pressing
TOP MENU or MENU on the player.
continued
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select the setting.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
Selecting a Playback Area
for an SACD Disc
1
4
7
2
3
6
9
5
8
0
Press ENTER.
SACD
MULTI/2CH
SACD/CD
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
X/x
ENTER
Note
DISPLAY
Repeat Play and A-B Repeat Play work only within
the titles of the selected type.
Selecting a playback area on a 2
channel + Multi-channel SACD
Some SACDs consist of a 2 channel playback
area and a multi-channel playback area. You
can select the playback area you want to
listen to.
Press SACD MULTI/2CH in stop mode.
Each time you press the button, the “MULTI”
indicator turns on and off in the front panel
display. When no indicator appears, the 2
channel playback area is selected.
To select a playback area using the
Control Menu
1 Press DISPLAY.
The Control Menu appears.
2 Press X/x to select
(MULTI/
2CH), then press ENTER.
3 Press X/x to select the playback area,
“MULTI” or “2CH,” then press ENTER.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a playback layer when
playing a hybrid SACD
Playing VIDEO CDs with
PBC Functions (PBC Playback)
Some SACDs consist of an HD layer and a
CD layer. You can select the playback layer
you want to listen to.
With PBC (Playback Control) functions, you
can enjoy simple interactive operations,
search functions, and other operations.
PBC playback allows you to play VIDEO
CDs interactively by following the menu on
the TV screen.
Press SACD/CD in stop mode.
Each time you press the button, an HD layer
or a CD layer is alternately selected. When
playing a CD layer, the “CD” indicator in the
front panel display lights up.
Notes
1
4
7
2
3
6
9
Number
buttons
5
8
0
• For details about SACD discs, see page 92 (Super
Audio CD).
• Each play mode function works only within the
selected layer or playback area.
./>
H
x
X/x
ENTER
ORETURN
1
2
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
Select the item number you want by
pressing X/x or the number
buttons.
3
4
Press ENTER.
Follow the instructions in the menu
for interactive operations.
Refer to the instructions supplied with
the disc, as the operating procedure may
differ according to the VIDEO CD.
continued
39
Download from Www.Somanuals.com. All Manuals Search And Download.
To go back to the menu
Press ORETURN.
Various Play Mode
z To play without using PBC, press ./> or
the number buttons while the player is stopped to
select a track, then press H or ENTER.
“Play without PBC.” appears on the TV screen and the
player starts continuous play. You cannot play still
pictures such as a menu.
Functions (Program Play, Shuffle
Play, Repeat Play, A-B Repeat Play)
You can set the following play modes:
• Program Play (page 41)
• Shuffle Play (page 43)
To return to PBC playback, press x twice then press
H.
• Repeat Play (page 44)
Note
• A-B Repeat Play (page 45)
Depending on the VIDEO CD, “Press ENTER” in
Step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case, press
H.
Note
• The play mode is canceled when:
– you open the disc tray.
– the player enters standby mode by pressing ?/1
on the remote.
– you turn the power off by pressing POWER on the
player.
Selecting the disc mode (One disc or
All discs)
You can play one disc or all of the discs in the
player. Before setting Program Play, Shuffle
Play, or Repeat Play, you must select whether
to set those play mode on one disc or all of the
discs.
ONE/ALL
open front door
H
X/x
ENTER
DISPLAY
40
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Press DISPLAY twice.
1 Press DISPLAY twice.
The Control Menu appears.
The Control Menu appears.
2 Press X/x to select
(ONE/
2 Press X/x to select
ALL DISCS) and press ENTER.
(PROGRAM) and press ENTER.
The options for “PROGRAM” appear.
The options for “ONE/ALL DISCS”
appear.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
(
(
)
)
1 2 2 7
1 8 3 4
ALL DISCS
ALL DISCS
ONE DISC
PLAY
DVD VIDEO
OFF
OFF
SET
ON
3 Press X/x to select “ SETt” and press
ENTER.
z You can select “ALL DISCS” or “ONE DISC” by
pressing ONE/ALL on the player. Each time you press
the button, the disc mode changes alternately.
The display for programming appears.
PROGRAM
Creating your own program (Program
Play)
– : ––––
T
ALL CLEAR
ALL
1. –––––
2. –––––
3. –––––
4. –––––
5. –––––
6. –––––
You can play the contents of the discs in the
order you want by arranging the order of the
discs, titles, chapters, or tracks to create your
own program. You can program up to 99
titles, chapters, and tracks. By selecting All
Discs mode (page 40), you can create a
program for all of the discs in the player.
4 Press c.
The player is ready to program the first
disc.
1
4
7
2
3
6
9
Number
buttons
5
8
0
PROGRAM
– : ––––
T
CLEAR
ALL CLEAR
ALL
1. –––––
2. –––––
3. –––––
4. –––––
5. –––––
6. –––––
SHUFFLE
PROGRAM
REPEAT
H
X/x/c
ENTER
DISPLAY
continued
41
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM
– : ––––
5 Select the disc you want to program
using the number buttons or X/x, then
press ENTER.
T
ALL CLEAR
1. 3DVD –T02–C03
ALL
–––––
–––––
–––––
–––––
–––––
2.
3.
4.
5.
6.
The cursor moves to the title or track (in
this case, “01”).
Tracks or titles
recorded on a disc
Disc type
Selected disc, title and chapter
PROGRAM
3 : DVD
T
C
ALL CLEAR
ALL
01
02
03
04
05
06
ALL
01
02
03
04
05
06
1. –––––
2. –––––
3. –––––
4. –––––
5. –––––
6. –––––
x When playing a VIDEO CD, SACD, or
CD
For example, select track “02.”
Press X/x or the number buttons to
select “02” under “T,” then press
ENTER.
Chapters recorded on a disc
A track number may be displayed in 3
digits for an SACD.
6 Select the title, chapter, or track you
0:15:30
T
PROGRAM
– : ––––
want to program.
ALL CLEAR
1. 3DVD –T02–C03
2. 2VCD –T02
ALL
x When playing a DVD
For example, select chapter “03” of title
“02.”
Press X/x or the number buttons to
select “02” under “T,” then press
ENTER.
–––––
–––––
–––––
–––––
3.
4.
5.
6.
Selected disc and track
PROGRAM
T
C
3 : DVD
ALL CLEAR
ALL
01
02
03
04
05
06
ALL
01
02
03
04
05
06
1. –––––
2. –––––
3. –––––
4. –––––
5. –––––
6. –––––
7 To program other titles, chapters, or
tracks, repeat Steps 4 to 6.
The programmed discs, titles, chapters,
and tracks are displayed in the selected
order.
Next, press X/xor the number buttons to
select “03” under “C,” then press
ENTER.
8 Press H to start Program Play.
Program Play begins.
When the program ends, you can restart
the same program again by pressing H.
To return to normal play
Press CLEAR, or select “OFF” in Step 3.
To play the same program again, select “ON”
in Step 3 and press H.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the Control Menu
Playing in random order (Shuffle
Play)
Press DISPLAY repeatedly until the Control
Menu is turned off.
To change or cancel a program
You can have the player “shuffle” discs,
titles, chapters, or tracks and play them in a
random order. Subsequent “shuffling” may
produce a different playing order. By
selecting All Discs mode (page 40), you can
shuffle all of the discs in the player.
1 Follow Steps 1 through 3 of “Creating
your own program (Program Play).”
2 Select the program number of the disc,
title, chapter, or track you want to change
or cancel using X/x or the number
buttons, and press c.
1
4
7
2
3
6
9
5
8
0
3 Follow Step 5 for new programming. To
cancel a program, select the program and
press CLEAR.
CLEAR
SHUFFLE
To cancel all the titles, chapters, or
tracks in the programmed order
H
X/x
ENTER
1 Follow Steps 1 through 3 of “Creating
DISPLAY
your own program (Program Play).”
2 Press X and select “ALL CLEAR.”
3 Then press ENTER.
z You can do Repeat Play or Shuffle Play of the
programmed titles, chapters, or tracks by pressing
REPEAT or SHUFFLE, or to activate “REPEAT” or
“SHUFFLE” during Program Play.
1 Press DISPLAY twice during playback.
The Control Menu appears.
z You can select “PROGRAM” directly by pressing
PROGRAM.
2 Press X/x to select
(SHUFFLE), then press ENTER.
The options for “SHUFFLE” appear.
Note
The number of titles, chapters, or tracks displayed are
the same number of titles, chapters, or tracks recorded
on a disc.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
OFF
OFF
DISC
TITLE
CHAPTER
continued
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing repeatedly (Repeat Play)
3 Press X/x to select the item.
x When playing a DVD VIDEO (Program
Play is set to “ OFF” )
You can play all discs, or all of the titles or
tracks on a disc or a single title, chapter, or
track repeatedly.
• DISC*: Shuffles discs and plays
them in random order.
• TITLE: Shuffles titles and plays
them in random order.
• CHAPTER: Shuffles chapters and
plays them in random order.
You can use a combination of Shuffle or
Program Play modes. By selecting All Discs
mode (page 40), you can repeat all of the
discs in the player.
x When playing a DVD-RW
• DISC*: Shuffles discs and plays
them in random order.
1
4
7
2
3
6
9
5
8
0
CLEAR
x When playing a VIDEO CD/SACD/CD
(Program Play is set to “OFF” )
• DISC*: Shuffles discs and plays
them in random order.
REPEAT
H
• TRACK: Shuffles tracks and plays
them in random order.
X/x
ENTER
*Appears only when you select All Discs
mode.
DISPLAY
x When Program Play is set to “ON”
• ON: Shuffles titles or tracks selected
in Program Play and plays them in
random order.
1 Press DISPLAY twice during playback.
4 Press ENTER.
The Control Menu appears.
2 Press X/x to select
To return to normal play
(REPEAT), the press ENTER.
The options for “REPEAT” appear.
Press CLEAR or select “OFF” in Step 3.
To turn off the Control Menu
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
Press DISPLAY repeatedly until the Control
Menu is turned off.
OFF
OFF
DISC
TITLE
CHAPTER
z You can set the Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option, press
H. Shuffle Play starts.
z You can select “SHUFFLE” directly by pressing
SHUFFLE. Each time you press the button, the item
changes.
3 Press X/x to select the item.
x When playing a DVD VIDEO (Program
Play and Shuffle Play are set to “OFF”)
• DISC: Repeats all of the titles on the
disc when you select One Disc
Note
Up to 96 chapters in a disc can be played in random
order when “CHAPTER” is selected.
mode, or all of the titles on all of the
44
Download from Www.Somanuals.com. All Manuals Search And Download.
discs when you select All Discs
mode.
• TITLE: Repeats the current title on a
Repeating a specific portion (A-B
Repeat Play)
disc.
• CHAPTER: Repeats the current
chapter.
You can play a specific portion of a title,
chapter, or track repeatedly. (This function is
useful when you want to memorize lyrics,
x When playing a DVD-RW
• DISC: Repeats all of the titles of the
selected type when you select One
Disc mode, or all of the titles on all
of the discs when you select All
Discs mode.
etc.)
)
1
4
7
2
3
6
9
5
8
0
CLEAR
• TITLE: Repeats the current title on a
disc.
A-B
• CHAPTER: Repeats the current
chapter.
X/x
x When playing a VIDEO CD/SACD/CD
(Program Play and Shuffle Play are set
to “OFF”)
ENTER
DISPLAY
• DISC: Repeats all of the tracks on a
disc when you select One Disc
mode, or all of the tracks on all of the
discs when you select All Discs
mode.
• TRACK: Repeats the current track.
1 Press DISPLAY twice during playback.
The Control Menu appears.
x When Program Play is set to “ON” or
Shuffle Play is activated
2 Press X/x to select
(A-B
• ON: Repeats Program Play or
Shuffle Play.
REPEAT), then press ENTER.
The options for “A-B REPEAT” appear.
4 Press ENTER.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
To return to normal play
OFF
SET
OFF
Press CLEAR or select “OFF” in Step 3.
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
z You can set Repeat Play while the player is
stopped. After selecting the “REPEAT” option, press
H. Repeat Play starts.
z You can select “REPEAT” directly by pressing
REPEAT. Each time you press the button, the item
changes.
continued
45
Download from Www.Somanuals.com. All Manuals Search And Download.
To return to normal play
3 Press X/x to select “ SET t,” then
press ENTER.
Press CLEAR, or select “OFF” in Step 3.
The “A-B REPEAT” setting display
appears.
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
z You can select “A-B REPEAT” directly by
pressing A-B. Press the button once to set the point A,
and press it again to set the point B.
A-B REPEAT
ENTER
Set point A with
.
Notes
• You can set A-B Repeat Play for only one specific
section.
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Program Play are
canceled.
• A-B Repeat Play does not work for titles containing
still pictures on a DVD-RW in VR mode.
• You cannot set the starting point (point A) on one
disc and ending point (point B) on another disc.
4 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A-B REPEAT
ENTER
Set point B with
.
CHAPTER TIME
A: 18
–
1 : 32 : 55
5 When you reach the ending point (point
B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
“A-B” appears on the front panel display
during A-B Repeat Play.
(
)
)
PLAY
DVD VIDEO
1 2 2 7
(
1 8 3 4
ON
CHAPTER TIME
A: 18
B: 18
–
–
1 : 32 : 55
1 : 34 : 30
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating a point quickly by playing a disc
in fast forward or fast reverse (Scan)
Searching for a Scene
Searching for a Particular
Point on a Disc (Search, Scan,
Slow-motion Play, Freeze Frame)
Press
or
while playing a disc.
When you find the point you want, press H
to return to normal speed.
Each time you press
or
during
scan, the playback speed changes. Three
speeds are available. With each press the
indication changes as follows:
You can locate a particular point on a disc
quickly by monitoring the picture or playing
back slowly.
Playback direction
×2B (DVD VIDEO/SACD/CD only)
/
FF2M T FF1M
/
H
Opposite direction
×2B (DVD VIDEO only)
FR2m T FR1m
The “×2B”/”×2b” playback speed is about
twice the normal speed. The “FF2M”/
”FR2m” playback speed is faster than
“FF1M”/”FR1m.”
Note
Depending on the DVD/VIDEO CD, you may not be
able to do some of the operations described.
Watching frame by frame (Slow-
motion Play)
Locating a point quickly (Search)
Press
or
when the player is in
During playback, keep pressing
locate a point in the playback direction or
keep pressing to locate a point in the
to
pause mode. To return to the normal speed,
press H.
Each time you press
or
during
opposite direction. When you find the point
you want, release the button to return to
normal playback speed.
Slow-motion Play, the playback speed
changes. Two speeds are available. With
each press the indication changes as follows:
Playback direction
SLOW2y y SLOW1y
Opposite direction (DVD only)
SLOW2
y SLOW1
The “SLOW2y”/”SLOW2 ” playback
speed is slower than “SLOW1y”/
”SLOW1 .”
continued
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing one frame at a time
Searching for a Disc/Title/
Chapter/Track/Index/
Scene (Search mode)
When the player is in the pause mode, press
to go to the next frame. Press
to go to the preceding frame (DVD VIDEO
only). If you hold the button down, you can
view the frames in succession. To return to
normal playback, press H.
You can search a DVD by disc, title or
chapter, and you can search a VIDEO CD/
SACD/CD by track, index, or scene.
As title and tracks are assigned unique
numbers on the disc, you can select the
desired one by entering its number. Or, you
can search for a scene using the time code.
1
4
7
2
3
6
9
Number
buttons
5
8
0
CLEAR
SEARCH
MODE
X/x
ENTER
DISPLAY
1
2
Press DISPLAY.
The Control Menu appears.
Press X/x to select the search
method.
x When playing a DVD VIDEO/DVD-RW
(DISC),
(TITLE),
(CHAPTER), or
(TIME/TEXT)
Select “TIME/TEXT” for “Time search”
(see below).
48
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a VIDEO CD
5
Press ENTER.
The player starts playback from the
(DISC),
(INDEX)
(TRACK)
or
selected number.
x When playing a VIDEO CD with PBC
Playback
(DISC),
x When playing an SACD/CD
(DISC), (TRACK)
(INDEX)
(SCENE)
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
or
To search for a scene using the time
code (Time search) (DVD VIDEO/DVD-
RW only)
Example: when you select
(CHAPTER)
“
(
)” is selected ( refers to a
** **
**
number).
1 In Step 2, select
(TIME/
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes or scenes.
TEXT).
“T
:
:
” (playing time of the
** ** **
current title) is selected.
1
PLAY
DVD VIDEO
2 Press ENTER.
(
(
)
)
1 2 2 7
1 8 3 4
T
“T
:
:
” changes to “T --:--:--.”
** ** **
1 : 3 2 : 5 5
3 Input the time code using the number
buttons, then press ENTER.
Selected row
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
z You can select “TITLE,” “CHAPTER,”
3
4
Press ENTER.
“TRACK,” “INDEX,” “SCENE” or “TIME/TEXT”
directly by pressing SEARCH MODE repeatedly.
“
(
)” changes to “-- ( ).”
** **
**
z When the Control Menu display is turned off, you
can search for a chapter (DVD VIDEO/DVD-RW) or
track (SACD/CD) by pressing the number buttons and
ENTER.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
–
–
3 4
T
1 : 3 2 : 5 5
z You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided into
9 scenes. You can start playback directly by selecting
one of the scenes. For details, see “Searching by Scene
(VIEWER).”
Press X/x or the number buttons to
select the title, chapter, track,
index, or scene number you want to
search.
Notes
• The title, chapter or track number displayed is the
same number recorded on the disc.
• You cannot search for a still picture on a DVD-RW
in VR mode.
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press ENTER.
Searching by Scene(VIEWER)
You can divide the screen into 9 sub-screens
and find the desired scene quickly.
To start playback from the selected
scene
Select the scene using C/X/x/c and press
ENTER. The playback starts from the
selected scene.
X
ENTER
To return to normal play
C/X/x/c
ORETURN
Press ORETURN.
DISPLAY
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
Notes
1
2
Press DISPLAY twice during
playback.
The Control Menu appears.
• Depending on the disc, you may not be able to select
all functions.
• The sound is muted when using this function.
Press X/x to select
(VIEWER), then press ENTER.
The options for “VIEWER” appear.
Scanning the title, chapter, or track
You can divide the screen into 9 sub-screens
and display the first scene of titles, chapters,
or tracks. You can also play back from the
selected title, chapter, or track.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
TITLE VIEWER
CHAPTER VIEWER
STROBE PLAYBACK
ANGLE VIEWER
Select the item you want in Step 3, then press
ENTER in Step 4.
TITLE VIEWER
xWhen playing a DVD VIDEO
Select “TITLE VIEWER” or “CHAPTER
VIEWER.”
3
Press X/x to select the item.
Refer to the explanations given for each
items in the following sections.
• TITLE VIEWER (for DVD VIDEO
only)
xWhen playing a VIDEO CD
Select “TRACK VIEWER.”
The initial scenes of titles, chapters, or tracks
appear.
• CHAPTER VIEWER (for DVD
VIDEO only)
• TRACK VIEWER (for VIDEO CD
only)
• STROBE PLAYBACK
• ANGLE VIEWER (for DVD VIDEO
only)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
z If there are more than 9 titles, chapters, or tracks,
V is displayed at the bottom right.
To display the additional titles, chapters, or tracks,
select the bottom right scene (the position 9) and press
x. To return to the previous scene, select the top left
scene (the position 1) and press X.
1
4
7
2
5
8
3
6
9
Dividing a scene into 9 sections
(STROBE PLAYBACK)
You can display 9 consecutive moving
pictures on the screen. When you press X,
the moving pictures pause.
Select “STROBE PLAYBACK” in Step 3,
then press ENTER in Step 4.
Displaying different angles
simultaneously
If various angles (multi-angles) for a scene
are recorded on the DVD VIDEO, you can
display all of the angles recorded on the disc
on the same screen, and start playback in
continuous mode at the chosen angle. The
angles are displayed on a screen divided into
9 sections.
Select “ANGLE VIEWER” in Step 3, then
press ENTER in Step 4.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
When playing a DVD VIDEO or DVD-
RW
Viewing Information About the Disc
Title playing time and current disc, title
and chapter number
Viewing the Playing Time
and Remaining Time on
the Front Panel Display
Remaining time of the current title
Playing time and
number of the current chapter
You can check information about the disc,
such as the remaining time, current title or
track number, using the front panel display
(page 9).
Remaining time of
the current chapter
0
TIME/TEXT
Text
When playing a VIDEO CD (without
PBC functions), SACD, or CD
Track playing time and current disc, track
and index number
Press TIME/TEXT.
Remaining time of the
current track
Each time you press TIME/TEXT while
playing the disc, the display changes as
shown in the following charts.
Playing time of the
disc
Remaining time of
the disc
Text
52
Download from Www.Somanuals.com. All Manuals Search And Download.
z When playing VIDEO CDs with PBC functions,
the scene number or the playing time is displayed.
Checking the Playing
Time and Remaining Time
z The playing time and remaining time of the current
chapter, title, track, scene, or disc will also appear on
your TV screen. See the following section “Checking
the Playing Time and Remaining Time” for
instructions on how to read this information.
You can check the playing time and
remaining time of the current title, chapter, or
track, and the playing time or remaining time
of the disc. Also, you can check the DVD/
SACD/CD text recorded on the disc.
Note
Depending on the type of disc being played and the
playing mode, the above mentioned disc information
may not be displayed.
0
TIME/
TEXT
DISPLAY
1
Press DISPLAY during playback.
The Control Menu appears.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
Time information
continued
53
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press TIME/TEXT repeatedly to
change the time information.
The display and the kinds of time that you
can change depend on the disc you are
playing.
TIME/TEXT
BRAHMS SYMPHONY NO – 4
The DVD/SACD/CD text
x When playing a DVD VIDEO or DVD-
RW
z If the DVD/SACD/CD text does not fit on a single
line, you can see the entire text by watching it scroll
across the front panel display.
• T
:
:
** ** **
Playing time of the current title
• T–
:
:
** ** **
z You can select the time and text directly by
Remaining time of the current title
• C
pressing TIME/TEXT.
:
:
** ** **
Playing time of the current chapter
Notes
• C–
:
:
** ** **
Remaining time of the current
chapter
• This player can only display the first level of DVD/
SACD/CD text, such as the disc’s name or title.
• Depending upon the disc, the text may not be
displayed.
x When playing a VIDEO CD (with PBC
functions)
•
:
** **
Playing time of the current scene
x When playing a VIDEO CD (without
PBC functions), SACD, or CD
• T
:
** **
Playing time of the current track
• T–
:
** **
Remaining time of the current track
• D
:
** **
Playing time of the current disc
• D–
:
** **
Remaining time of the current disc
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
Checking the DVD/SACD/CD text
Press TIME/TEXT repeatedly in Step 2 to
display the text recorded on the DVD/SACD/
CD. The DVD/SACD/CD text appears only
when the text is recorded in the disc. You
cannot change the text. If the disc does not
contain text, “NO TEXT” appears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press ENTER.
Checking the Play
Information (ADVANCED)
To close the ADVANCED window
Select “OFF” in Step 3.
You can check information such as the bit
rate or the disc layer that is being played.
While playing a disc, an approximate bit rate
of the playback picture is always displayed as
Mbps (Mega bit per second) and the audio as
kbps (kilo bit per second).
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
Display of each item
By pressing DISPLAY repeatedly, you can
display either “BIT RATE” or “LAYER,”
whichever was selected in “ADVANCED.”
X/x
BIT RATE
ENTER
DISPLAY
BIT RATE
Audio
Video
384kbps
Mbps
10
0
5
Bit rate refers to the amount of video/audio
data per second in a disc. The higher the bit
rate, the larger the amount of data. When the
bit rate level is high, there is a large amount
of data. However, this does not always mean
that you can get higher quality pictures or
sounds.
1
2
Press DISPLAY during playback.
The Control Menu is displayed.
Press X/x to select
(ADVANCED), then press ENTER.
The options for “ADVANCED” appear.
LAYER
Appears when the DVD
has dual layers
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
OFF
BIT RATE
LAYER
BIT RATE
BIT RATE
384kbps
Mbps
10
0
5
Indicates the approximate point where the
disc is playing.
If it is a dual-layer DVD, the player indicates
which layer is being read (“Layer 0” or
“Layer 1”).
For details on the layers, see page 92 (DVD
VIDEO).
3
Press X/x to select items.
For each item, please refer to “Displays
of each item.”
• BIT RATE: displays the bit rate.
• LAYER: displays the layer and the
pick-up point.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
Sound Adjustments
1 : 3 2 : 5 5
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
1: ENGLISH
1: ENGLISH
2: ENGLISH
3: FRENCH
Changing the Sound
L
C
R
LFE
LS
RS
If the DVD VIDEO is recorded with
multilingual tracks, you can select the
language you want while playing the DVD
VIDEO.
If the DVD VIDEO is recorded in multiple
audio formats (PCM, Dolby Digital, or DTS),
you can select the audio format you want
while playing the DVD VIDEO.
3
Press X/x to select the desired
audio signal.
x When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
With stereo CDs or VIDEO CDs, you can
select the sound from the right or left channel
and listen to the sound of the selected channel
through both the right and left speakers. (In
this case, the sound loses its stereo effect.)
For example, when playing a disc containing
a song with the vocals on the right channel
and the instruments on the left channel, you
can select the left channel and hear the
instruments from both speakers.
When 4 digits are displayed, they
represent the language code. Refer to the
language code list on page 97 to see
which language the code represents.
When the same language is displayed two
or more times, the DVD VIDEO is
recorded in multiple audio formats.
x When playing a DVD-RW
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
AUDIO
Example:
• 1: MAIN (main sound)
• 1: SUB (sub sound)
• 1: MAIN+SUB (main and sub
sound)
X/x
ENTER
DISPLAY
x When playing a VIDEO CD or CD
The default setting is underlined.
• STEREO: The standard stereo
sound
• 1/L: The sound of the left channel
(monaural)
• 2/R: The sound of the right channel
(monaural)
1
2
Press DISPLAY during playback.
The Control Menu is displayed.
4
Press ENTER.
Press X/x to select
(AUDIO), then press ENTER.
The options for “AUDIO” appear.
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
z You can select “AUDIO” directly by pressing
AUDIO. Each time you press the button, the item
changes.
**The letters in the program format display
mean the following sound component.
L:
R:
C:
Front (left)
Front (right)
Center
Notes
• While playing a DVD, the sound may change
automatically.
• You cannot change the sound for SACDs.
LS: Rear (left)
RS: Rear (right)
S:
Rear (monaural): The rear
Displaying the audio information of
the disc
component of the Dolby Surround
processed signal and the Dolby
Digital signal
When you select “AUDIO,” the channels
being played are displayed on the screen.
For example, in Dolby Digital format,
multiple signals ranging from monaural to
5.1 channel signals can be recorded on a
DVD. Depending on the DVD, the number of
the recorded channels may differ.
LFE: Low Frequency Effect signal
The display examples are as follows:
• PCM (stereo)
PROGRAM FORMAT
PCM 96kHz 24bit
L
R
Current audio format*
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
• Dolby Surround
1 : 3 2 : 5 5
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
1: ENGLISH
PROGRAM FORMAT
DOLBY DIGITAL 2/0
DOLBY SURROUND
L
C
R
L
C
R
LFE
LS
RS
Currently playing program format**
S
• Dolby Digital 5.1ch
When an LFE signal component is output,
“LFE” is enclosed in a solid line. When an
LFE signal component is not output, “LFE”
is enclosed in a broken line.
*“PCM,” “DTS,” or “DOLBY DIGITAL” is
displayed.
In the case of “DOLBY DIGITAL,” the
channels in the playing track are displayed
by numbers as follows:
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
L
C
R
For Dolby Digital 5.1 ch:
LFE
LS
RS
Rear component 2
DOLBY DIGITAL 3 / 2.1
Front component 2+
Centre component 1
LFE (Low Frequency
Effect) component 1
continued ,
57
Download from Www.Somanuals.com. All Manuals Search And Download.
• DTS
When an LFE signal component is output,
“LFE” is enclosed in a solid line. When an
LFE signal component is not output, “LFE”
is enclosed in a broken line.
SURROUND Mode Settings
PROGRAM FORMAT
DTS 3/2.1
You can enjoy surround sounds while
playing discs including Dolby Digital and
DTS DVDs, even if you have only 2 or 4
speakers. Select surround mode that best
suits your speaker setup.
L
C
R
LFE
LS
RS
SURROUND
z When the signal contains rear signal components
such as “LS,” “RS” or “S,” the Surround effect is
enhanced (page 58).
X/x
ENTER
DISPLAY
1
2
Press DISPLAY during playback.
The Control Menu appears.
Press X/x to select
(SURROUND), then press ENTER.
The options for “SURROUND” appear.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
OFF
OFF
TVS DYNAMIC
3
Press X/x to select one of the
surround modes.
Refer to the following explanations given
for each item.
For 2 speaker setups
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
• TVS STANDARD
58
Download from Www.Somanuals.com. All Manuals Search And Download.
For 4 to 6 speaker setups
(If you select “NONE” in the setting of
“REAR” in “SPEAKER SETUP” (page
86), you cannot select these modes.)
• NORMAL SURROUND
TV
• ENHANCED SURROUND
• VIRTUAL REAR SHIFT
• VIRTUAL MULTI REAR
• VIRTUAL MULTI DIMENSION
TVS WIDE
Uses sound imaging to create virtual rear
speakers from the sound of the front speakers
(L, R) without using actual rear speakers. The
virtual speakers are reproduced as shown in
the illustration below. This gives the sound
an expanded effect that fills the area
surrounding the listener.
This mode is effective when the distance
between the front L and R speakers is short,
4
Press ENTER.
To cancel the setting
Select “OFF” in Step 3.
To turn off the Control Menu
such as with built-in speakers on a stereo TV.
Press DISPLAY repeatedly until the Control
Menu is turned off.
.
TV
For 2 speaker setups
When you connect only 2 front speakers,
TVS (TV Virtual Surround) lets you enjoy
surround sound effects by using sound
imaging to create virtual rear speakers from
the sound of the front speakers (L: left, R:
right) without using actual rear speakers.
Select one of the following modes:
TVS NIGHT
The large sounds, such as explosions, are
suppressed, but the quieter sounds are
unaffected. This feature is useful when you
don’t want to disturb other people but still
want to hear the dialog and enjoy the
surround sound effects of “TVS WIDE.”
If the player is set up to output the signal from
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, the surround effect will be
heard only when “DOLBY DIGITAL” and
“DTS” are set to “D-PCM” in “AUDIO
SETUP” (page 84).
TVS DYNAMIC
Uses sound imaging to create virtual rear
speakers from the sound of the front speakers
(L, R) without using actual rear speakers. The
virtual speakers are reproduced as shown in
the illustration below. The sound imaging
effect is distinct and clearly reproduces each
aural element of the audio track.
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
continued ,
59
Download from Www.Somanuals.com. All Manuals Search And Download.
TVS STANDARD
speaker, the appropriate sounds for the center
speaker will be delivered.
Uses sound imaging to create virtual rear
speakers from the sound of the front speakers
(L, R) without using actual rear speakers. The
virtual speakers are reproduced as shown in
the illustration below. Use this setting when
you want to use TVS with 2 separate speakers
and retain the sound quality.
L
R
L
R
LS
RS
ENHANCED SURROUND
Provides a greater sense of presence from a
Dolby Surround (Pro Logic) source with a
monaural rear channel signal. Produces a
stereo like effect in the rear channels.
VIRTUAL REAR SHIFT
L: Left front speaker
R: Right front speaker
: Virtual speakers
Uses sound imaging to shift the sound of the
rear speakers away from the actual speaker
position.
The virtual speakers are reproduced as shown
in the illustration below. The shift position
differs according to “REAR” or “SIDE”
setting of the rear speakers (page 86).
For 4 to 6 speaker setups
You can enjoy the following surround effects
by using the 2 front speakers and 2 rear
speakers.
REAR
L
R
Connect the player to the amplifier (receiver)
B-1
with the
connection (page 22).
You can experience Dolby Surround (Pro
Logic) sounds or Digital Cinema Sound
(DCS). DCS uses sound imaging to shift the
sound of the rear speakers away from the
actual speaker position or create entire sets of
virtual rear speakers from one set of actual
rear speakers. “VIRTUAL REAR SHIFT,”
“VIRTUAL MULTI REAR,” and
LS
RS
SIDE
L
R
“VIRTUAL MULTI DIMENSION” make
use of this technology.
LS
RS
NORMAL SURROUND
Software with 2 channel audio signals is
decoded with the Dolby Surround (Pro
Logic) decoder to create surround effects.
The rear speakers will emit identical
monaural sounds. If you are using a center
60
Download from Www.Somanuals.com. All Manuals Search And Download.
VIRTUAL MULTI REAR
REAR
L
R
Uses sound imaging to create an array of
virtual rear speakers from a single pair of
actual rear speakers. The virtual speakers are
reproduced as shown in the illustration
below. The position of the virtual rear
speakers differs according to “REAR” or
“SIDE” setting of the rear speakers (page 86).
LS
RS
REAR
L
R
SIDE
L
R
LS
RS
LS
RS
SIDE
L
R
L: Left front speaker
R: Right front speaker
LS: Left rear speaker
RS: Right rear speaker
: Virtual speakers
LS
RS
z You can select “SURROUND” directly by
pressing SURROUND. Each time you press the
button, the item changes. If you select any setting
other than “OFF,” the SURROUND indicator on the
player lights up.
VIRTUAL MULTI DIMENSION
Uses sound imaging to create an array of
virtual rear speaker positions higher than the
listener from a single pair of actual rear
speakers.
Notes
This mode creates five sets of virtual
speakers surrounding the listener at
approximately a 30° angle of elevation. The
effect differs according to “REAR” or
“SIDE” setting of the rear speakers (page 86).
• To enjoy the multichannel audio through the 5.1CH
OUTPUT jacks, correctly set each speaker position
and distance. For details on setting each speaker, see
page 86.
• When you select an item, the sound cuts off for a
moment.
• When the playing signal does not contain a signal for
the rear speakers (page 57), the surround effects may
be difficult to hear.
• When you select “TVS DYNAMIC,” “TVS WIDE,”
“TVS NIGHT”, or “TVS STANDARD,” the player
does not output the sound from the center speaker.
• When you select one of the surround modes, turn off
the surround setting of the connected TV or
amplifier (receiver).
continued ,
61
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the player is set up to output the signal from the
DIGITAL OUT (OPTICAL or COAXIAL) jack, the
TVS effect will not be heard when you play a CD.
• Make sure that your listening position is between
and at an equal distance from your speakers, and that
the speakers are located in similar surroundings.
Otherwise, the TVS effect may be hard to discern.
• “TVS NIGHT” only works with Dolby Digital discs.
However, not all discs will respond to the “TVS
NIGHT” function in the same way.
• If you use the DIGITAL OUT (OPTICAL or
COAXIAL) jack and set “DOLBY DIGITAL” to
“DOLBY DIGITAL,” and “DTS” to “DTS,” in
“AUDIO SETUP,” sound will come from your
speakers but it will not have the TVS effect.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
Enjoying Movies
1 8 3 4
T
1 : 3 2 : 5 5
Changing the Angles
(
)
1
9
If various angles (multi-angles) for a scene
are recorded on the DVD VIDEO, “ANGLE”
appears in the front panel display. This means
that you can change the viewing angle.
For example, while playing a scene of a train
in motion, you can display the view from
either the front of the train, the left window of
the train or from the right window without
having the train’s movement interrupted.
3
4
Press c or ENTER.
The number of the angle changes to “-.”
PLAY
DVD VIDEO
1
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
(
)
–
9
1
4
7
2
3
6
9
Number
buttons
5
8
0
Select the angle number using the
number buttons or X/x, then press
ENTER.
ANGLE
The angle changes to the selected angle.
X/x
ENTER
To turn off the Control Menu
DISPLAY
Press DISPLAY repeatedly until the Control
Menu is turned off.
z You can select the angle directly by pressing
ANGLE. Each time you press the button, the angle
changes.
1
2
Press DISPLAY during playback.
The Control Menu appears.
z You can display all the angles recorded on the disc
on the same screen, and start playback directly in
continuous mode from the chosen angle. The angles
are displayed on a screen divided into 9 sections. For
details, see page 50.
Press X/x to select
(ANGLE).
The number of the angle appears.
The number in parentheses indicates the
total number of angles.
Note
Depending on the DVD VIDEO, you may not be able
to change the angles even if multi-angles are recorded
on the DVD VIDEO.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate the language code. Refer to
“Language Code List” on page 97 to see
which language the code represents.
Displaying the Subtitles
If subtitles are recorded on the disc, you can
turn the subtitles on and off whenever you
want while playing. If multilingual subtitles
are recorded on the disc, you can change the
subtitle language while playing, and turn it on
or off whenever you want. For example, you
can select the language you want to practice
and turn the subtitles on for better
x When playing a DVD-RW
Select “ON.”
4
Press ENTER.
To cancel the SUBTITLE setting
understanding.
Select “OFF” in Step 3.
SUBTITLE
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
X/x
z You can select “SUBTITLE” directly by pressing
SUBTITLE. Each time you press the button, the item
changes.
ENTER
DISPLAY
Note
Depending on the DVD VIDEO, you may not be able
to change the subtitles even if multilingual subtitles
are recorded on it.
1
2
Press DISPLAY during playback.
The Control Menu appears.
Press X/x to select
(SUBTITLE), then press ENTER.
The options for “SUBTITLE” appear.
1
PLAY
DVD VIDEO
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
OFF
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
3
Press X/x to select the setting.
x When playing a DVD VIDEO
Select the language.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select a level.
As the value increases, the mosaic like
patterns on your TV screen will decrease.
• 1: reduces the “block noise”.
• 2: reduces the “block noise” more than
1.
Adjusting the Picture
Quality (BNR)
The Block Noise Reduction (BNR) function
adjusts the picture quality by reducing the
“block noise” or mosaic like patterns that
appear on your TV screen.
• 3: reduces the “block noise” more than
2.
Press ENTER.
The disc plays with the setting you
selected.
1
4
7
2
3
6
9
5
8
0
BNR
To cancel the “BNR” setting
Select “OFF” in Step 3.
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
X/x
ENTER
z You can select “BNR” directly by pressing BNR.
Each time you press the button, the item changes. If
you select any setting other than “OFF,” the indicator
on the player lights up.
DISPLAY
Notes
• If the outlines of the images on your screen should
become blurred, set “BNR” to “OFF.”
• Depending on the disc or the scene being played, the
“BNR” effect may be hard to discern.
1
2
Press DISPLAY twice during
playback.
The Control Menu appears.
Press X/xtoselect
then press ENTER.
(BNR),
The options for “BNR” appear.
(
)
)
PLAY
DVD VIDEO
1 2 2 7
(
1 8 3 4
OFF
1
2
3
OFF
65
Download from Www.Somanuals.com. All Manuals Search And Download.
• DYNAMIC 1: produces a bold dynamic
picture by increasing the picture
contrast and the color intensity.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and the color intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: White colors become
brighter and black colors become
richer, and the color contrast is
increased.
Adjusting the Playback
Picture(VIDEO EQUALIZER)
You can adjust the video signal of the DVD
or VIDEO CD from the player, not from the
TV, to obtain the picture quality you want.
Choose the video mode that suits the program
you are watching.
4
Press ENTER.
X/x
ENTER
DISPLAY
To turn off the Control Menu
Press DISPLAY repeatedly until the Control
Menu is turned off.
z When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
1
2
Press DISPLAY twice during
playback.
The Control Menu appears.
Press X/x to select
(VIDEO EQUALIZER), then press
ENTER.
The options for “VIDEO EQUALIZER”
appear.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
STANDARD
DYNAMIC 1
DYNAMIC 2
CINEMA 1
CINEMA 2
STANDARD
3
Press X/x to select the setting you
want.
• STANDARD: displays a standard
picture.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
As the value increases, the outlines of
images on your TV screen will become
crisper.
Enhancing the Playback
Picture (DIGITAL VIDEO ENHANCER)
• 1: enhances the outline.
• 2: enhances the outline more than 1.
• 3: enhances the outline more than 2.
• SOFT: softens the image (DVD
VIDEO/DVD-RW only).
The Digital Video Enhancer function makes
the picture appear clear and crisp by
enhancing the outlines of images on your TV
screen. Also, this function can soften the
images on the screen.
4
Press ENTER.
The disc plays with the setting you
selected.
1
4
7
2
3
6
9
5
8
0
DVE
To cancel the “DIGITAL VIDEO
ENHANCER” setting
Select “OFF” in Step 3.
To turn off the Control Menu
X/x
ENTER
Press DISPLAY repeatedly until the Control
Menu is turned off.
DISPLAY
z You can select “DIGITAL VIDEO ENHANCER”
directly by pressing DVE. Each time you pressing the
button, the item changes.
Note
Depending on the DVD/VIDEO CD disc or the scene
being played, noise found in the disc may become
more apparent. If this happens, it is recommended that
you use the BNR function (page 65) with the DVE
function. If the condition still does not improve,
reduce the Digital Video Enhancer level or select
“SOFT” (DVD VIDEO/DVD-RW only) in Step 3
above.
1
2
Press DISPLAY twice during
playback.
The Control Menu appears.
Press X/x to select
(DIGITAL VIDEO ENHANCER), then
press ENTER.
The options for “DIGITAL VIDEO
ENHANCER” appear.
(
)
)
1 2 2 7
PLAY
DVD VIDEO
(
1 8 3 4
OFF
1
2
3
SOFT
OFF
3
Press X/x to select a level.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
The Control Menu appears.
Using Various Additional
Functions
3 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Locking Discs (Custom Parental
Control, Parental Control)
The options for “PARENTAL
CONTROL” appear.
1
STOP
DVD VIDEO
You can set two kinds of playback
restrictions for the desired disc.
• Custom Parental Control
(
(
)
)
1 2 2 7
1 8 3 4
T
1 : 3 2 : 5 5
You can set the playback restrictions so that
the player will not play inappropriate discs.
• Parental Control
ON
PLAYER
PASSWORD
OFF
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users.
The same password is used for both Parental
Control and Custom Parental Control.
4 Press X/x to select “ON t,” then
press ENTER.
x If you have not entered a password
The display for registering a new
password appears.
Custom Parental Control
You can set the same Custom Parental
Control password for up to 50 discs. When
you set the fifty-first disc, the first disc is
canceled.
PARENTAL CONTROL
Enter a new 4-digit password, then
ENTER
press
.
1
4
7
2
3
6
9
5
8
0
Number
buttons
Enter a 4-digit password by using the
number buttons, then press ENTER.
The display for confirming the password
appears.
x When you have already registered a
password
The display for entering the password
appears.
x
C/X/x/c
ENTER
DISPLAY
ORETURN
PARENTAL CONTROL
1 Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
Enter password, then press ENTER
.
2 Press DISPLAY while the player is in
stop mode.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Control (limiting playback
by children)
5 Enter or re-enter your 4-digit password
by using the number buttons, then press
ENTER.
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
A scene that is limited is not played, or it is
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu display.
To turn off the Custom Parental
Control function
replaced by a different scene.
.
1 Follow Steps 1 through 3 of “Custom
Parental Control.”
1
4
7
2
3
6
9
Number
buttons
5
8
0
2 Press X/x to select “OFF t,” then press
ENTER.
3 Enter your 4-digit password using the
number buttons, then press ENTER.
H
To play the disc for which Custom
Parental Control is set
X/x
ENTER
DISPLAY
ORETURN
1 Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
1 Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
CUSTOM PARENTAL CONTROL
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Custom parental control is already
set. To play, enter your password
ENTER
and press
.
The options for “PARENTAL
CONTROL” appear.
1
STOP
DVD VIDEO
(
(
)
)
1 2 2 7
2 Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
1 8 3 4
T
1 : 3 2 : 5 5
ON
PLAYER
PASSWORD
OFF
z If you forget your password, enter the 6-digit
number “199703” using the number buttons when the
“CUSTOM PARENTAL CONTROL” display asks
you for your password, then press ENTER. The
display will ask you to enter a new 4-digit password.
continued ,
69
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press X/xto select “ PLAYER t,” then
5 Press X/x to select “STANDARD,” then
press ENTER.
press ENTER.
The selection items for “STANDARD”
are displayed.
x If you have not entered a password
The display for registering a new
password appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
USA
PARENTAL CONTROL
OTHERS
Enter a new 4-digit password, then
ENTER
press
.
6 Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
The area is selected.
When you select “OTHERS t,” select
and enter the standard code in the table on
page 71 using the number buttons.
x When you have already registered a
password
The display for entering the password
appears.
7 Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
PARENTAL CONTROL
Enter password, then press ENTER
.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
OFF
8:
7: NC17
6:
5:
R
4 Enter or re-enter your 4-digit password
by using the number buttons, then press
ENTER.
The display for setting the playback
limitation level appears.
8 Select the level you want using X/x,
then press ENTER.
Parental Control setting is complete.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
PARENTAL CONTROL
LEVEL:
STANDARD:
4: PG13
USA
70
Download from Www.Somanuals.com. All Manuals Search And Download.
The lower the value, the more strict the
limitation.
Area Code
Standard
Code
Standard
Code
number
number
To turn off the Parental Control
function
Argentina
Australia
Austria
Belgium
Brazil
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
Korea
2304
2363
2362
Malaysia
Mexico
Set “LEVEL” to “OFF” in Step 8.
Netherlands 2376
New Zealand 2390
To play a disc for which Parental
Control is set
Canada
Chile
Norway
Pakistan
Philippines
Portugal
Russia
2379
2427
2424
2436
2489
2501
2149
2499
1 Insert the disc and press H.
The “PARENTAL CONTROL” display
appears.
China
Denmark
Finland
France
2 Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
Singapore
Spain
z If you forget your password, remove the disc and
repeat Steps 1 to 3 of “Limiting playback by children.”
When you are asked to enter your password, enter
“199703” using the number buttons, then press
ENTER. The display will ask you to enter a new 4-
digit password. After you enter a new 4-digit password
in Step 4, replace the disc in the player and press H.
When the “PARENTAL CONTROL” display
appears, enter your new password.
Germany
Hong Kong 2219
Sweden
India
2248
2238
2254
2276
Switzerland 2086
Indonesia
Italy
Taiwan
2543
2528
2184
Thailand
Japan
United
Kingdom
Notes
• When you play DVD VIDEOs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the DVD VIDEO, you may be asked
to change the parental control level while playing the
disc. In this case, enter your password, then change
the level. If the Resume Play mode is canceled, the
level returns to the original level.
continued
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the password
Operation Sound Effects
(Sound Feedback)
1 Press DISPLAY while the player is in
stop mode.
The player beeps when the following
operations are performed.
The Control Menu appears.
The default setting of the Sound Feedback
function is set to off.
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Operation
Operation sound
One beep
The options for “PARENTAL
CONTROL” appear.
Power is turned on
Power is turned off
H is pressed
Two beeps
One beep
3 Press X/x to select “ PASSWORD t,”
then press ENTER.
Two beeps
X is pressed
The display for entering the password
appears.
Playback is stopped
Operation is not possible
One long beep
Three beeps
4 Enter your 4-digit password using the
To set Sound Feedback
number buttons, then press ENTER.
5 Enter a new 4-digit password using the
POWER
number buttons, then press ENTER.
Power indicator
A
X
6 To confirm your password, re-enter it
using the number buttons, then press
ENTER.
If you make a mistake entering your
password
?/1
1
4
7
2
3
6
9
Press C before you press ENTER in Step 5
and input the correct number.
5
8
0
If you make a mistake
Press ORETURN.
1 Press POWER on the player, then press
?/1 on the remote.
To turn off the Control Menu
The power indicator lights up in green.
When there is a disc in the player, press
A and remove the disc. Then press A
again to close the disc tray.
Press DISPLAY repeatedly until the Control
Menu is turned off.
2 Press and hold X on the player for more
than two seconds.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
You will hear one beep and the Sound
Feedback function is turned on.
Controlling Your TV or AV
Amplifier (Receiver) with
the Supplied Remote
To turn off the Sound Feedback
function
When there is no disc in the player, press and
hold X on the player for more than two
seconds. You will hear two beeps and the
Sound Feedback function is turned off.
By adjusting the remote signal, you can
control your TV with the supplied remote.
If you connect the player with an AV
amplifier (receiver), you can control the
volume with the supplied remote.
Notes
• Depending on the units being connected, you may
not be able to control your TV or AV amplifier
(receiver) using some of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the
code number you have set may be reset to the default
setting. Set the appropriate code number again.
Controlling TVs with the remote
TV/DVD
switch
?/1
1
4
7
2
3
6
9
VOL +/–
5
8
0
Number
buttons
TV/VIDEO
WIDE MODE
ENTER
1 Slide the TV/DVD switch to “TV.”
2 Hold down ?/1, and enter your TV’s
manufacturer’s code (see the table)
using the number buttons.
3 Release ?/1.
continued ,
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Code numbers of controllable TVs
Controlling the volume of your AV
amplifier (receiver) with the remote
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
.
TV/DVD
switch
Manufacturer Code
number
Manufacturer Code
number
[/1
1
4
7
2
3
6
9
VOL +/–
Number
buttons
Sony (default) 01
Panasonic
Philco
06,19
5
8
0
Akai
04
04
12
03
03,04
08,21
16
AOC
Philips
Centurion
Coronado
Pioneer
Portland
Quasar
03
Curtis-Mathes 12
06,18
05,14
04,10
12
Daytron
Emerson
Fisher
12
Radio Shack
03,04,14 RCA
11 Sampo
1 Slide the TV/DVD switch to DVD.
2 Hold down [/1, and enter your AV
amplifier (receiver)’s manufacturer’s
code (see the table below) using the
number buttons.
General Electric 06,10
Samsung
20
Gold Star
Hitachi
03,04,17 Sanyo
11
02,03
04,12
09
Scott
12
J.C.Penney
JVC
Sears
07,10,11
03,05,18
08,12
03,08,14
07
Sharp
Sylvania
3 Release [/1.
KMC
03
Magnavox
Marantz
03,08,12 Teknika
04,13 Toshiba
Code numbers of controllable AV
amplifiers (receivers)
MGA/
04,12,13, Wards
03,04,12
12
Mitsubishi
17
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your AV amplifier
(receiver).
If you do not connect an AV amplifier
(receiver), you can control your TV’s volume
by setting the code number to 90 (default).
However, you must first set the code number
of controllable TVs as explained above.
Yorx
NEC
04,12
Zenith
15
Controlling the TV
When you set the TV/DVD switch to TV, you
can control the following items with the
supplied remote.
By pressing
[/1
You can
Manufacturer
Sony
Code number
80, 88, 89, 91
84, 85, 86
92, 93
Turn the TV on or off
Adjust the volume of the TV
VOL +/–
Denon
WIDE MODE
Switch to or from the wide
mode of a Sony Wide TV
Kenwood
Onkyo
TV/VIDEO
Switch the TV’s input source
between the TV and other
input sources
81, 82, 83
99
Pioneer
Sansui
87
Number buttons Select the channel of the TV
and ENTER
Technics
Yamaha
97, 98
94, 95, 96
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the AV amplifiers
(receivers)
Controlling the CD changer
The controls indicated below are effective
while the MEGA CONTROL button is lit.
When you set the TV/DVD switch to DVD,
you can control the volume of the AV
amplifier (receiver) using VOL +/–.
./>
x
N
X
Controlling a CD Changer
(Mega Control)
MEGA CONTROL
You can control a Sony CD changer of 5/50/
200/300/400 discs connected to the MEGA
CONTROL jack of the player.
TV/DVD
switch
1
4
7
2
3
6
9
5
8
0
Connecting the CD changer
./>
X
Do not connect anything
CONTROL A1 cord
(not supplied)
to the other CONTROL
A1 jack.
H
x
X/x
ENTER
Audio cord (not supplied)
1 Set the command mode selector of the
CD changer to “CD3.”
2 Set the TV/DVD switch on the remote to
“ DVD.”
3 Turn on the player and the CD changer.
4 Press MEGA CONTROL on the player.
The MEGA CONTROL button on the
front panel lights up and the display
shows the current disc number in the CD
changer.
SACD/DVD player
Sony CD changer
(5/50/200/300/400
discs)
5 Select the play mode you want on the CD
changer.
continued , 75
Download from Www.Somanuals.com. All Manuals Search And Download.
• When the MEGA CONTROL button is lit, you
6 Press H on the player to start playing.
Playback starts and the display shows the
current disc and track numbers and the
playing time of the track. While the
cannot use the Control Menu.
MEGA CONTROL button on the front
panel is lit, you can control CD changer
with the controls on the player as follows:
To
Operation
Select a disc during
playback
Press the number
button on the remote
and ENTER, or X/
x and ENTER
Stop
Press x
Pause
Press X
Resume play after pause
Press X or H
Press >
Go to the next track or
scene in continuous play
mode
Go back to the preceding
track or scene in
Press .
continuous play mode
To control the player again
Press MEGA CONTROL on the player.
The MEGA CONTROL button on the player
turns off and you can control the player.
Notes
• Connect only a Sony 5/50/200/300/400 CD changer
to MEGA CONTROL jack.
• Set CONTROL A1 or CONTROL A1II in the setup
menu of the CD changer so that it matches the
connection made above. Refer to the operating
instructions supplied with the CD changer.
• You cannot locate a particular point on a CD’s track
using the controls on the player.
• Depending on the CD changer, some controls on the
player may not operate the CD changer as they do
the player.
• You cannot control the player when the MEGA
CONTROL button on the front panel is lit.
• The player will not enter Resume Play after the
MEGA CONTROL button on the front panel has
been turned on and off.
• You cannot control the CD changer right after
turning on the player or connecting the CD changer.
Wait a few seconds until the player recognizes the
CDs.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
STOP
DVD VIDEO
(
)
4 7
:
Settings and Adjustments
:
Using the Setup Display
QUICK
CUSTOM
RESET
QUICK
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for
the subtitles and the Setup Display, among
other things. For details on each Setup
Display item see page 78 through 88. For an
overall list of Setup Display items, see page
98.
3 Press X/x to select “ CUSTOM” and
press ENTER.
The Setup Display appears.
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
MENU:
AUDIO:
SUBTITLE:
Note
Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
How to use the Setup Display
4 Press X/x to select the setup item from
the displayed list: “ LANGUAGE SETUP,”
“ SCREEN SETUP,” “ CUSTOM SETUP,”
“ AUDIO SETUP” or “ SPEAKER SETUP.”
Then press ENTER.
X/x
ENTER
DISPLAY
The selected setup item appears.
Example: “SCREEN SETUP”
Setup items
SCREEN SETUP
4:3 LETTER BOX
ON
TV TYPE:
SCREEN SAVER
:
BACKGROUND:
JACKET PICTURE
1 Press DISPLAY on the remote when the
player is in stop mode.
Selected item
The Control Menu appears.
2 Press X/x to select
(SETUP)
and press ENTER.
The options for “SETUP” appear.
continued ,
77
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Select an item using X/x, then press
ENTER.
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
The options for the selected item appear.
Example: “TV TYPE”
SCREEN SETUP
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
TV TYPE:
SCREEN SAVER
BACKGROUND:
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display
or sound track.
:
Options
Select “LANGUAGE SETUP” in the Setup
Display. For details on using the display, see
“Using the Setup Display” (page 77).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
6 Select a setting using X/x, then press
ENTER.
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
The setting is selected and setup is
complete.
Example: “16:9”
Selected setting
SCREEN SETUP
xOSD (On-Screen Display)
16:9
ON
TV TYPE:
SCREEN SAVER
:
Switches the display language on the screen.
Selects the language from the displayed list.
BACKGROUND:
JACKETPICTURE
xMENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
xAUDIO (DVD VIDEO only)
Switches the language of the sound track.
Select the language from the displayed list.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
To turn off the Setup Display
Press DISPLAY repeatedly until the Setup
Display is turned off.
z If you select “QUICK” in Step 3, you will enter the
Quick Setup mode (page 28).
Follow from Step 5 of the Quick Setup explanation to
make basic adjustments.
xSUBTITLE (DVD VIDEO only)
Switches the language of the subtitles
recorded on the DVD VIDEO.
Select the language from the displayed list.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z If you select “RESET” in Step 3, you can reset all
of the “SETUP” settings on page 98 to the default
settings. After you select “RESET” and press ENTER,
select “YES” and press ENTER to reset the settings (it
takes a few seconds to complete), or select “NO” and
press ENTER to return to the Control Menu. Do not
press POWER or ?/1 when resetting the player.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
z If you select “OTHERS t” in “MENU,”
“SUBTITLE,” and “AUDIO,” select and enter the
language code from the list using the number buttons
(page 97).
Settings for the Display
(SCREEN SETUP)
Note
Choose settings according to the TV to be
connected.
When you select a language that is not recorded on the
DVD VIDEO, one of the recorded languages will be
automatically selected (except for the “OSD”).
Select “SCREEN SETUP” in the Setup
Display. For details on using the display, see
“Using the Setup Display” (page 77).
The default settings are underlined.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 LETTER BOX
ON
JACKET PICTURE
xTV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the screen.
4:3 PAN
SCAN
Select this when you connect a
4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
portions that do not fit.
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
continued ,
79
Download from Www.Somanuals.com. All Manuals Search And Download.
xBACKGROUND
4:3 LETTER BOX
4:3 PAN SCAN
Selects the background color or picture on the
TV screen in stop mode or while playing a
SACD/CD.
JACKET
The jacket picture (still picture)
appears in the background, but
only when the jacket picture is
already recorded on the disc
(CD-EXTRA, etc.). If the disc
does not contain a jacket picture,
the “GRAPHICS” picture
appears.
PICTURE
16:9
GRAPHICS A preset picture stored in the
player appears in the background.
BLUE
The background color is blue.
The background color is black.
Note
BLACK
Depending on the DVD, “4:3 LETTER BOX” may be
selected automatically instead of “4:3 PAN SCAN” or
vice versa.
xSCREEN SAVER
Turns on and off the screen saver so that the
screen saver image appears when you leave
the player in pause or stop mode for 15
minutes, or when you play back an SACD/
CD for more than 15 minutes. The screen
saver will help prevent your display device
from becoming damaged (ghosting). Press
H to turn off the screen saver.
ON
Turns on the screen saver.
Turns off the screen saver.
OFF
80
Download from Www.Somanuals.com. All Manuals Search And Download.
xDIMMER
Adjusts the lighting of the front panel
display.
Custom Settings (CUSTOM
SETUP)
BRIGHT
DARK
OFF
Makes the front panel display
bright.
Use this to set up playback related and other
settings.
Makes the front panel display
dark.
Select “CUSTOM SETUP” in the Setup
Display. For details on using the display, see
“Using the Setup Display” (page 77).
The default settings are underlined.
Turns off the lighting of the front
panel display.
xPAUSE MODE (DVD VIDEO/DVD-RW
only)
CUSTOM SETUP
AUTO PLAY:
OFF
BRIGHT
AUTO
ON
Selects the picture in pause mode.
DIMMER:
PAUSE MODE:
PLAYBACK MEMORY:
TRACK SELECTION:
CD DIRECT:
AUTO
The picture, including subjects
that move dynamically, is output
with no jitter. Normally, select
this position.
OFF
OFF
FRAME
The picture, including subjects
that do not move dynamically, is
output in high resolution.
xAUTO PLAY
Selects the Auto Play setting when you turn
on the player.
xPLAYBACK MEMORY (DVD VIDEO/
VIDEO CD only)
OFF
Does not use “TIMER,”
“DEMO1,” or “DEMO2” to start
playback.
The player can store the “SUBTITLE” and
other settings of each disc for up to 50 discs
(Playback Memory).
Set the Playback Memory function “ON” or
“OFF.”
TIMER
Starts playing when the player is
turned on. The player can be
played at any time when
connected to a timer (not
ON
Stores the settings in memory
when you eject the disc.
supplied). Set the timer when the
player is in standby mode (the ?/
1 indicator lights up in red).
OFF
Does not store the settings in
memory.
DEMO1
DEMO2
Starts playing the first
demonstration automatically.
The following settings are stored in memory
by the Playback Memory function.
–ANGLE (page 63)*
Starts playing the second
demonstration automatically.
–AUDIO (page 56)*
–BNR (page 65)
–DIGITAL VIDEO ENHANCER (page 67)
–SUBTITLE (page 64)*
–VIDEO EQUALIZER (page 66)
* DVD VIDEO only
continued ,
81
Download from Www.Somanuals.com. All Manuals Search And Download.
xCD DIRECT
Notes
Eliminates the use of unnecessary circuits
when playing CDs. The setting will be
activated when you press DISC SKIP.
This function affects the output of the
following jacks:
–LINE OUT L/R (AUDIO) 1/2 jacks
–5.1CH OUTPUT jacks
–PHONES jack
• The player can store the settings of up to 50 discs.
When you store the setting of disc number 51, the
first disc setting is canceled.
• The Playback Memory function cannot be used for
DVD-RWs in VR mode.
• During playback, do not turn off the player by
pressing POWER on the player. Doing so may
cancel the settings. When you turn off the player,
press x first to stop playback and then press [/1 on
the remote. After the power indicator lights up in red
and the player enters standby mode, press POWER
on the player.
OFF
ON
Select this when playing CD
discs, including CD type DTS
discs.
Eliminates the use of
unnecessary circuits needed to
play CDs.
xTRACK SELECTION (DVD VIDEO
only)
Gives the sound track which contains the
highest number of channels priority when
you play a DVD on which multiple audio
formats (PCM, DTS or Dolby Digital format)
are recorded.
Note
If you select “ON” when playing CD type DTS discs,
the sound will become noisy.
OFF
No priority given.
Priority given.
AUTO
Notes
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 78).
• If PCM, DTS and Dolby Digital sound tracks have
the same number of channels, the player selects
PCM, DTS and Dolby Digital sound tracks in this
order.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
xAUDIO DRC (Dynamic Range
Control) (DVD VIDEO/DVD-RW only)
Settings for the Sound
(AUDIO SETUP)
Makes the sound clear when the volume is
turned down when playing a DVD that has
the “AUDIO DRC” function. This affects the
output from the following jacks:
–LINE OUT L/R (AUDIO) 1/2 jacks
–5.1CH OUTPUT jacks
“AUDIO SETUP” allows you to set the
sound according to the playback and
connection conditions.
–DIGITAL OUT (OPTICAL or COAXIAL)
jack only when “DOLBY DIGITAL” is set
to “D-PCM” in “DIGITAL OUT” (page
84).
Select “AUDIO SETUP” in the Setup
Display. For details on using the display, see
“Using the Setup Display” (page 77).
The default settings are underlined.
–PHONES jack
AUDIO SETUP
STANDARD Normally, select this position.
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
SHARP
TV MODE
Makes the low sounds clear even
if you turn the volume down. It
is especially recommended
when you listen to the sound
using the speakers of the TV.
DOLBY SURROUND
ON
D-PCM
D-PCM
48kHz/96kHz PCM:
48kHz/16bit
WIDE
RANGE
Gives you the feeling of being at
a live performance. When you
use high quality speakers, it is
even more effective.
xAUDIO ATT (attenuation)
If the playback sound is distorted, set this
item to “ON.” The player reduces the audio
output level.
xAUDIO FILTER (except SACD)
This function affects the output of the
following jacks:
–LINE OUT L/R (AUDIO) 1/2 jacks
–5.1CH OUTPUT jacks
Selects the digital filter to reduce noises
above the 22.05 kHz (Sampling frequency
(Fs) of the audio sources is 44.1 kHz), 24 kHz
(Fs is 48 kHz), or 48 kHz (Fs is above 96
kHz).
–PHONES jack
OFF
ON
Turns off the audio attenuation.
Normally, select this position.
SHARP
SLOW
Provides a wide frequency
range and spatial feeling.
Reduces the audio output level so
that no sound distortion occurs.
Select this when the playback
sound from the speakers is
distorted.
Provides smooth and warm
sound.
Notes
• There may be little effect by changing the digital
filter depending on discs or playback environment.
• There is no effect on SACDs.
continued ,
83
Download from Www.Somanuals.com. All Manuals Search And Download.
xDOWNMIX (DVD VIDEO/DVD-RW
Note
only)
SACD audio signals are not output from a digital jack.
Switches the mixing down methods when
you play a DVD on which rear signal
components such as “LS,” “RS,” or “S” are
recorded in Dolby Digital or DTS format. For
details on the rear signal components, see
“Changing the Sound” (page 56). This
function affects the output of the following
jacks:
–LINE OUT L/R (AUDIO) jacks
–DIGITAL OUT (OPTICAL or COAXIAL)
jack when “DOLBY DIGITAL” is set to
“D-PCM” in “DIGITAL OUT” (page 84).
–PHONES jack
Setting the digital output signal
Switches the method of outputting audio
signals when you connect the following
component using an optical or coaxial digital
cord via the DIGITAL OUTPUT (OPTICAL
or COAXIAL) jack.
–Amplifier (receiver) with digital input jack
–Amplifier (receiver) with a built-in DTS or
Dolby Digital decoder
–MD or DAT deck
For connection details, see page 24.
Select “DOLBY DIGITAL,” “DTS” and
“48kHz/96kHz PCM” after setting
“DIGITAL OUT” to “ON.”
DOLBY
Select this when the player is
SURROUND connected to an audio
component that conforms to
Dolby Surround (Pro Logic).
The output signals which
reproduce the Dolby Surround
effect are downmixed to 2
channels.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
OFF
STANDARD
SHARP
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
ON
D-PCM
D-PCM
NORMAL
Select this when the player is
connected to an audio
48kHz/96kHz PCM:
48kHz/16bit
component that does not
conform to Dolby Surround (Pro
Logic). All of the output signals
are downmixed to 2 channels
without the Dolby Surround
(Pro Logic) effect.
xDOLBY DIGITAL (DVD VIDEO/DVD-
RW only)
Selects the Dolby Digital signals output via
the DIGITAL OUT (OPTICAL or
COAXIAL) jack.
xDIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)
jack.
D-PCM
Select this when the player is
connected to an audio component
lacking a built-in Dolby Digital
decoder. You can select whether
the signals conform to Dolby
Surround (Pro Logic) or not by
making adjustments to the
ON
Normally, select this position. When
you select “ON,” set “DOLBY
DIGITAL,” “DTS” and “48kHz/96kHz
PCM.” For details on setting these
items, see “Setting the digital output
signal.”
“DOWNMIX” item in “AUDIO
SETUP” (page 84).
OFF
The player does not output the audio
signals via the DIGITAL OUT
(OPTICAL or COAXIAL) jack. The
influence of the digital circuit upon the
analog circuit is minimal.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
DOLBY
DIGITAL
Select this when the player is
connected to an audio component
with a built-in Dolby Digital
decoder. If the player is connected
to an audio component lacking a
built-in Dolby Digital decoder, do
not set this. Otherwise, when you
play the Dolby Digital sound track,
a loud noise (or no sound) will
come out from the speakers,
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for copyright
protection purposes, the signal is
only output as 48kHz/16bit.
If a receiver (amplifier) which
cannot accept 96kHz is
connected to the player, do not
set this. Otherwise, a loud noise
may come out from the
affecting your ears or causing the
speakers to be damaged.
speakers.
xDTS (DVD VIDEO only)
Notes
Selects if DTS signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)
jack.
• Even if you set “48kHz/96kHz PCM” in “AUDIO
SETUP” to “96kHz/24bit,” the sampling frequency
is converted to 48kHz/16bit when a “SURROUND”
mode (page 58) is selected.
• The analog audio signals from the LINE OUT L/R
(AUDIO) 1/2 jacks and 5.1CH OUTPUT jacks are
not affected by this setting and keep their original
sampling frequency level.
D-PCM Select this when the player is
connected to an audio component
lacking a built-in DTS decoder. If you
play DTS audio sound tracks, the
player outputs stereo signals via the
DIGITAL OUT (OPTICAL or
COAXIAL) jack.
DTS
Select this when the player is
connected to an audio component
having a built-in DTS decoder. If the
player is connected to an audio
component lacking a built-in DTS
decoder, do not set this. Otherwise,
when you play the DTS sound track, a
loud noise (or no sound) will come
out from the speakers, affecting your
ears or causing the speakers to be
damaged.
x48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal to be output via the DIGITAL OUT
(OPTICAL or COAXIAL) jack.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted to
48kHz/16bit.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
LARGE Normally select this position.
Settings for the Speakers
(SPEAKER SETUP)
SMALL When the sound cracks or the
surround sound effects are difficult to
hear, select this. This activates the
bass redirection circuitry and outputs
the bass frequencies of the center
speaker from other speakers.
To obtain the best possible surround sound,
set the size of the speakers you have
connected and their distance from your
listening position. Then use the test tone to
adjust the volume and the balance of the
speakers to the same level.
• REAR
NONE If you do not connect rear speakers,
select this.
This setting is effective when connecting the
speaker with 5.1CH OUTPUT jacks (page
22).
Select “SPEAKER SETUP” in the setup
display. For details, see “Using the Setup
Display” (page 77).
LARGE (REAR/SIDE): Normally select this
position. Select either of these
according to the rear speaker’s
position*.
SMALL (REAR/SIDE): When the sound
cracks or the surround sound effects
are difficult to hear, select this.
Select either of these according to the
rear speaker’s position*.
The default settings are underlined.
SPEAKER SETUP
SIZE:
This activates the bass redirection
circuitry and outputs the bass
frequencies of the rear speaker from
other speakers.
DISTANCE:
BALANCE:
LEVEL:
TEST TONE:
FRONT:
OFF
LARGE
LARGE
LARGE REAR
YES
CENTER:
REAR:
SUBWOOFER:
(
)
* Rear speaker position
Correctly specify the location of the rear speakers to
enjoy the surround effect.
To return to the default setting
• Set to the “SIDE,” if the location of the rear speakers
corresponds to section A below.
Select the item, then press CLEAR. Note that
only the SIZE setting does not return to the
default setting.
• Set to the “REAR,” if the location of the rear
speakers corresponds to section B below.
This setting affects only “VIRTUAL REAR SHIFT,”
“VIRTUAL MULTI REAR,” and “VIRTUAL
MULTI DIMENSION” mode (page 58).
These settings do not affect the SACD Multi audio
signals.
xSIZE
Selects the size of the speakers to be
connected.
• FRONT
LARGE Normally select this position.
SMALL When the sound cracks or the
surround sound effects are difficult to
hear, select this. This activates the
bass redirection circuitry and outputs
the bass frequencies of the front
speaker from the subwoofer.
90
45
• CENTER
20
NONE If you do not connect a center
speaker, select this.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
• SUBWOOFER
NONE If you do not connect a subwoofer,
select this. This activates the bass
redirection circuitry and outputs the
LFE signals from the front speakers as
long as the front speaker size is set to
“LARGE.”
10ft/3m
10ft/3m
10ft/3m
YES
If you connect a subwoofer, select this
to output the LFE (low frequency
effect) channel from the subwoofer.
When you set the other speakers
settings to “SMALL,” the subwoofer
makes up for the missing bass
10ft/3m
10ft/3m
frequencies of the speakers.
Notes
Be sure to change the value in the Setup
Display when you move the speakers. The
default adjustments are in parentheses.
• The cut off frequency for the subwoofer is fixed at
120 Hz.
• If your speakers are too small to reproduce low bass
frequencies, please set all speaker settings to
“SMALL” and utilize a subwoofer for low
frequency sound.
• Even if there are fewer than 6 speakers connected,
the player distributes the audio signal components to
the front speakers.
FRONT
(10ft/3m)
Front speaker distance from the
listening position can be set in 1
foot (0.3 meter) increments from
4 to 50 feet (1.2 to 15.2 meters).
CENTER
(10ft/3m)
Center speaker distance can be
moved up to 2 feet (0.6 meters)
backward from the front
xDISTANCE
speakers or 5 feet (1.5 meters)
forward closer to the listening
position, in 1 foot (0.3 meter)
increments.
In order to set the distance for each speaker,
first set the distance from the listening
position to the front speaker using FRONT.
This will automatically set the same distance
for the CENTER and REAR speakers. Then,
starting from these settings, change the
distance for the center and rear speakers as
explained below so that they match the actual
physical distance to your listening position.
The default distance setting for the speakers
in relation to the listening position is shown
below.
REAR (10ft/ Rear speaker distance can be
3m)
moved up to 16 feet (4.8 meters)
closer to your listening position
from the front speaker position,
in 1 foot (0.3 meter) increments.
Notes
• If each of the front or rear speakers are not placed at
an equal distance from your listening position, set
the distance according to the closest speaker.
• Do not place the rear speakers farther away from
your listening position than the front speakers.
• These settings do not affect the SACD Multi audio
signals.
continued ,
87
Download from Www.Somanuals.com. All Manuals Search And Download.
xBALANCE
ON
The test tone is emitted from
each speaker in sequence while
adjusting balance or level.
You can vary the balance of the left and right
speakers as follows. Be sure to set “TEST
TONE” to “ON” for easy adjustment.
When you select one of the
“SPEAKER SETUP” items, the
test tone is emitted from both left
and right speakers simultaneously.
The default adjustments are in parentheses.
FRONT
(0dB)
Adjust the balance between the
front left and right speakers (–
6dB [L] to +6dB [R], 0.5dB
increments).
Adjusting the speaker volume and
level
REAR (0dB) Adjust the balance between the
rear left and right speakers (–
6dB [L] to +6dB [R], 0.5dB
increments).
1 Select “SPEAKER SETUP” in the Setup
Display.
2 Select “TEST TONE” and set to “ ON.”
You will hear the test tone from each
speaker in sequence.
xLEVEL
You can vary the level of each speaker as
follows. Be sure to set “TEST TONE” to
“ON” for easy adjustment.
3 From your listening position, select
“BALANCE” or “LEVEL” and adjust the
value of “BALANCE” using C/c and
“LEVEL” using X/x.
The default adjustments are in parentheses.
FRONT (0dB) Adjust the level of the front
speakers (–6dB to 0dB, 0.5
dB increments).
The test tone is emitted from both left and
right speakers simultaneously.
CENTER
(0dB)
Adjust the level of the center
speaker (–12dB to 0dB,
0.5dB increments).
4 Select “TEST TONE” and set to “OFF” to
turn off the test tone.
REAR (0dB)
Adjust the level of the rear
speakers (–12dB to 0dB,
0.5dB increments).
SUBWOOFER Adjust the level of the
Notes
(0dB)
subwoofer (–10dB to +10dB,
• When you adjust the speaker settings, the sound cuts
off for a moment.
0.5dB increments).
• The test tone signals are not output from the digital
jack.
To adjust the volume of all the
speakers at one time
Use the amplifier’s (receiver’s) volume
control.
xTEST TONE
The speakers will emit a test tone. Use this
when you use the 5.1CH OUTPUT jacks and
adjust the “BALANCE” and “LEVEL.”
OFF
The test tone is not emitted from
the speakers.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound
Additional Information
There is no sound.
, The connecting cord is not connected securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 22, 24,
26).
, The amplifier (receiver) input is not changed
so that you can listen to the player.
, The player is in pause mode or in Slow-motion
Play mode.
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through the
DIGITAL OUT (OPTICAL or COAXIAL)
jack, check the audio settings (page 83).
, SACD audio signals are not output from a
digital jack.
Power
The power is not turned on.
, Check that the AC power cord is connected
securely.
Sound is noisy.
Picture
, The disc is dirty or flawed.
There is no picture.
, The connecting cords are not connected
securely.
, The connecting cords are damaged.
, The player is not connected to the correct TV
input jack (page 18).
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 83).
, The video input on the TV is not set so that you
can view pictures on the player.
The surround effect is difficult to hear
when you are playing a Dolby Digital,
or DTS sound track.
Picture noise appears.
, Check the speaker connections and setting
(page 22, 24, 26).
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV, the copy-
protection signal applied to some DVD
programs could affect picture quality. If you
still experience problems even when you
connect your player directly to your TV,
please try connecting your player to your TV’s
S video input (page 18).
, Depending on the DVD, the output signal may
not be the entire 5.1 channels. It may be
monaural or stereo even if the sound track is
recorded in Dolby Digital or DTS format.
The sound comes from the center
speaker only.
, Depending on the disc, the sound may come
from the center speaker only.
, Set “SURROUND” to “OFF” in the Control
Menu display (page 58).
Even though you set the aspect ratio
in “TV TYPE” of “SCREEN SETUP,”
the picture does not fill the screen.
, The aspect ratio of the disc is fixed on your
DVD.
continued ,
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Playback stops automatically.
, Some discs may contain an auto pause signal.
While playing such a disc, the player stops
playback at the auto pause signal.
The remote does not function.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote sensor
on the player.
You cannot perform some functions
such as stop, Search, Scan, Slow-
motion Play, Repeat Play, Shuffle
Play, or Program Play.
, The batteries in the remote are weak.
, Depending on the disc, you may not be able to
do some of the operations above. See the
operating manual that comes with the disc.
The disc does not play.
, There is no disc inside.
, The disc is turned over. Insert the disc with the
playback side facing down on the disc tray.
, The disc is skewed.
, The player cannot play CD-ROMs, etc. (page
6).
The language for the sound track
cannot be changed.
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD prohibits the changing of the
language for the sound track.
, Try using the DVD’s menu instead of the
direct selection buttons on the remote (page
37).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player.
Remove the disc and leave the player turned
on for about half an hour. Turn on the power
again before playing the disc (page 3).
, The player cannot play DVD-Rs, DVD-RWs,
CD-Rs, or CD-RWs that are not finalized.
The subtitle language cannot be
changed.
The disc does not start playing from
the beginning.
, Try using the DVD’s menu instead of the
direct selection buttons on the remote (page
37).
, Multilingual subtitles are not recorded on the
DVD being played.
, Program Play, Shuffle Play, Repeat Play or A-
B Repeat Play has been selected (page 40).
Press CLEAR to cancel these functions before
playing a disc.
, Resume Play has been selected.
During stop, press x on the player or the
remote and then start playback (page 36).
, Depending upon the disc, the menu may
automatically appear on the TV screen.
, The DVD prohibits the changing of the
subtitles.
The subtitle cannot be turned off.
, Try using the DVD’s menu instead of the
direct selection buttons on the remote (page
37).
The player starts playing the disc
automatically.
, The DVD prohibits the subtitles being turned
off.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is set
to “TIMER” (page 81).
90
Download from Www.Somanuals.com. All Manuals Search And Download.
The angles cannot be changed.
Self-diagnosis Function
(When letters/numbers appear in the
display)
, Try using the DVD’s menu instead of the
direct selection buttons on the remote (page
37).
, Multi-angles are not recorded on the DVD
being played. The angle can be changed when
the “ANGLE” indicator lights up on the front
panel display (page 9).
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 00)
with a combination of a letter and digits
appears on the screen and the front panel
display. In this case, check the following
table.
, The DVD prohibits changing of the angles.
The player does not operate properly.
, When static electricity, etc., causes the player
to operate abnormally, press POWER on the
player to turn the player off and then on again.
C:13:00
Nothing is displayed on the front
panel display.
, “DIMMER” in “CUSTOM SETUP” is set to
“OFF.” Set “DIMMER” to “BRIGHT” or
“DARK” (page 81).
First three Cause and/or corrective
characters action
of the
service
5 numbers or letters are displayed on
the screen and on the front panel
display.
number
, The self-diagnosis function was activated.
C 13
C 31
The disc is dirty.
, Clean the disc with a soft cloth
(page 7).
(See the table on page 91.)
The disc cannot be removed and
“LOCKED” appears on the front panel
display.
The disc is not inserted correctly.
, Re-insert the disc correctly.
E XX (xx is a To prevent a malfunction, the
number)
player has performed the self-
diagnosis function.
, Contact your Sony dealer or local authorized
Sony service facility.
, Contact your nearest Sony
dealer or local authorized
Sony service facility and give
the 5-character service
number.
Example: E 61 10
91
Download from Www.Somanuals.com. All Manuals Search And Download.
discrete channels of high quality digital
audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
Glossary
Chapter (page 9)
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
DVD VIDEO (page 6)
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
The data capacity of a single-layer and
single-sided DVD is 4.7 GB (Giga Byte),
which is 7 times that of a CD. The data
capacity of a double-layer and single-sided
DVD is 8.5 GB, a single-layer and double-
sided DVD is 9.4 GB, and double-layer and
double-sided DVD is 17 GB.
Digital Cinema Sound (DCS) (page 58)
Technology that Sony developed to enjoy
surround in a home using 4 or more speakers.
It simulates the sound of a movie editing
studio instead of the usual concert hall so that
you can enjoy the surround sound of a movie
theater in the comfort of your own home.
Dolby Digital (page 20, 84)
The picture data uses the MPEG 2 format,
one of the worldwide standards of digital
compression technology. The picture data is
compressed to about 1/40 (average) of its
original size. The DVD also uses a variable
rate coding technology that changes the data
to be allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more real audio
presence.
Digital audio compression technology
developed by Dolby Laboratories. This
technology conforms to 5.1-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. Dolby Digital provides the same
5.1 discrete channels of high quality digital
audio found in Dolby Digital cinema audio
systems. Good channel separation is realized
because all of the channel data are recorded
discretely and little deterioration is realized
because all channel data processing is digital.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
Dolby Surround (Pro Logic) (page 84)
Audio signal processing technology that
Dolby Laboratories developed for surround
sound. When the input signal contains a
surround component, the Pro Logic process
outputs the front, center, and rear signals. The
rear channel is monaural.
DVD-RW (page 6)
A DVD-RW is a recordable and rewritable
disc with the same size as the DVD VIDEO.
The DVD-RW can be recorded in two
different modes: VR mode and Video mode.
VR (Video Recording) mode enables various
programming and editing functions, some of
which are limited in the case of Video mode.
Video mode complies with DVD VIDEO
format and is compatible with DVD players
while a DVD-RW recorded in VR mode can
only be played on DVD-RW compliant
players. The “DVD-RW” appears in this
DTS (page 20, 85)
Digital audio compression technology that
Digital Theater Systems, Inc. developed.
This technology conforms to 5.1-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. DTS provides the same 5.1
92
Download from Www.Somanuals.com. All Manuals Search And Download.
manual, or the on-screen display refers to
DVD-RWs in VR mode.
• Super Audio CD (single layer disc)
This disc consists of a single HD layer*.
*High density signal layer for the Super
Audio CD
Index (CD)/Video Index (VIDEO CD) (page
48)
A number that divides a track into sections to
easily locate the point you want on an SACD/
CD or VIDEO CD. Depending on the disc, no
index may be recorded.
HD (high density)
layer
• Super Audio CD (dual layer disc)
This disc consists of dual HD layers and is
capable of extended play over long periods.
Also, as the dual layer disc consists of dual
HD layers on one side only, you do not have
to turn the disc over during playback.
Parental Control (page 68)
A function of the DVD used to limit playback
of the disc according to the age of the user
and the limitation level in each country. The
limitation varies from disc to disc; when it is
activated, or playback is completely
prohibited, violent scenes are skipped or
replaced with other scenes, etc.
HD layer
HD layer
Region Code (page 6)
• Super Audio CD + CD (Hybrid disc)
This disc consists of an HD layer and a CD
layer. Also, as the dual layers are on one
side only, you do not have to turn the disc
over during playback. You can play the CD
layer using a conventional CD player.
This system is used to protect copyrights. A
region number is allocated on each DVD
player or DVD disc according to the sales
region. Each region code is shown on the
player as well as on the disc packaging. The
player can play the discs that match its region
code. The player can also play discs with the
ALL
mark. Even when the region code is not
shown on the DVD, the region limit may still
be activated.
CD layer
HD layer
Scene (page 9)
• 2 channel + Multi-channel Super Audio CD
This disc consists of the 2 channel playback
area and the multi-channel playback area.
On a VIDEO CD with PBC (playback
control) functions, the menu screens, moving
pictures and still pictures are divided into
sections called “scenes.”
2 channel playback
area
Super Audio CD (SACD) (page 6)
Multi-channel
playback area
An SACD disc can reproduce sounds that are
extremely faithful to the original sound by
use of DSD (Direct Stream Digital)
Title (page 9)
technology. This technology utilizes a
sampling frequency of 2.8224 MHz, which is
64 times that of a conventional CD, and 1-bit
quantization that enables the disc to hold 4
times the amount of information that a
standard PCM format CD can hold. SACDs
are divided into the following types.
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
continued ,
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Track (page 9)
Sections of a picture or a music feature on an
SACD/CD or VIDEO CD (the length of a
song).
TV Virtual Surround (TVS) (page 58)
Technology from Sony developed to produce
surround sound for home use using just a
stereo TV. Designed to work with the sound
characteristics of your TV, this technology
brings the excitement of surround sound to
your home using nothing more than your
stereo TV’s internal speakers. Furthermore,
various TVS modes are available. For
example, “TVS WIDE” uses just two
speakers to create a virtual sound
environment that makes you feel like you are
surrounded by multiple speakers.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
System
Laser
Signal format system
Semiconductor laser
NTSC
Audio characteristics
Frequency response
DVD (PCM 96 kHz): 2 Hz to 44 kHz (-2 dB ± 2.0 dB at 44 kHz)
SACD: 2 Hz to 100 kHz (-3 dB ± 2.0 dB at 50 kHz)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio)
Harmonic distortion
115 dB (DVD VIDEO) (LINE OUT L/R (AUDIO) 1/2 jacks only)
0.003 %
Dynamic range
DVD VIDEO/SACD: 103 dB
CD: 99 dB
Wow and flutter
Less than detected value (±0.001% W PEAK)
Outputs
Jack name
Jack type
Output level
Load impedance
DIGITAL OUT
(OPTICAL)
Optical output jack
-18 dBm
Wave length 660 nm
DIGITAL OUT
(COAXIAL)
Phono jack
0.5 Vp-p
75 ohms terminated
LINE OUT L/R
(AUDIO) 1/2
Phono jack
2 Vrms (at 50 kilohms) Over 10 kilohms
5.1CH OUTPUT
Phono jack
2 Vrms (at 50 kilohms) Over 10 kilohms
LINE OUT (VIDEO) 1/2 Phono jack
1.0 Vp-p
75 ohms, sync negative
S VIDEO OUT 1/2
4-pin mini DIN
Y: 1.0 Vp-p
C: 0.286 Vp-p
75 ohms, sync negative
75 ohms terminated
COMPONENT VIDEO Phono jack
OUT (Y, PB, PR)
Y: 1.0 Vp-p
PB, PR: 0.7 Vp-p
75 ohms, sync negative
75 ohms
AUDIO IN L/R
MEGA CONTROL
PHONES
Phono jack
Mini jack
-
47 kilohms
-
-
Phone jack
12 mW
32 ohms
General
Power requirements
Power consumption
Dimensions (approx.)
120 V AC, 60 Hz
17 W
430 × 108 × 414 mm (17 × 4 3/8 × 16 3/8 in.) (width/height/depth)
including projecting parts
Mass (approx.)
5.5 kg (12 lb. 2 oz.)
Operating temperature
Operating humidity
5°C to 35°C (41°F to 95°F)
25% to 80%
continued ,
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied accessories
See page 15.
Specifications and design are subject to change without notice.
ENERGY STAR is a U.S. registered mark. As an ENERGY STAR Partner, Sony Corporation has determined
that this product meets the ENERGY STAR guidelines for energy efficiency.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
For details, see pages 56, 64, 78.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1186 Scots
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1369 Nepali
1376 Dutch
1379 Norwegian
1393 Occitan
1403 (Afan)
Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1503 Singhalese
1505 Slovak
1506 Slovenian
Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1313 Latin
1525 Telugu
1527 Tajik
1528 Thai
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1703 Not
specified
1345 Malagasy
97
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Setup Display Items
The default settings are underlined.
LANGUAGE SETUP (page 78)
OSD
ENGLISH
FRENCH
SPANISH
PORTUGUESE
MENU
ENGLISH
FRENCH
SPANISH
PORTUGUESE
GERMAN
ITALIAN
DUTCH
CHINESE
JAPANESE
DANISH
SWEDISH
FINNISH
NORWEGIAN
RUSSIAN
OTHERS t
AUDIO
ORIGINAL
(All other selections are same as the “MENU” language.)
SUBTITLE
AUDIO FOLLOW
(All other selections are same as the “MENU” language.)
SCREEN SETUP (page 79)
TV TYPE
4:3 LETTER BOX
4:3 PAN SCAN
16:9
SCREEN SAVER
BACKGROUND
ON
OFF
JACKET PICTURE
GRAPHICS
BLUE
BLACK
98
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOM SETUP (page 81)
AUTO PLAY
OFF
TIMER
DEMO1
DEMO2
DIMMER
BRIGHT
DARK
OFF
PAUSE MODE
AUTO
FRAME
PLAYBACK MEMORY
TRACK SELECTION
CD DIRECT
ON
OFF
OFF
AUTO
OFF
ON
AUDIO SETUP (page 83)
AUDIO ATT
AUDIO DRC
OFF
ON
STANDARD
TV MODE
WIDE RANGE
AUDIO FILTER
DOWNMIX
SHARP
SLOW
DOLBY SURROUND
NORMAL
DIGITAL OUT
ON
DOLBY
D-PCM
DOLBY DIGITAL
DIGITAL
DTS
D-PCM
DTS
48kHz/96kHz 48kHz/16bit
PCM 96kHz/24bit
OFF
continued ,
99
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER SETUP (page 86)
SIZE
FRONT
LARGE
SMALL
CENTER
NONE
LARGE
SMALL
REAR
NONE
LARGE (REAR)
LARGE (SIDE)
SMALL (REAR)
SMALL (SIDE)
SUBWOOFER
NONE
YES
DISTANCE
FRONT
4ft ~ 50ft (1.2m ~ 15.2m)
(The distance from the
listening position.)
CENTER
0ft ~ 52ft (0m ~ 15.8m)
(It changes according to the distance from the front
speaker.)
REAR
0ft ~ 50ft (0m ~ 15.2m)
(It changes according to the distance from the front
speaker.)
BALANCE
LEVEL
FRONT
– 6dB ~ + 6dB
– 6dB ~ + 6dB
– 6dB ~ 0dB
REAR
FRONT
CENTER
REAR
– 12dB ~ 0dB
– 12dB ~ 0dB
– 10dB ~ + 10dB
SUBWOOFER
TEST TONE
OFF
ON
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Control Menu Display 12
Front Panel Display 9
Setup Display 77
DISTANCE 87
PLAY LIST 37
PLAYBACK MEMORY 81
PROGRAM 41
Numerics
16:9 79
4:3 LETTER BOX 79
4:3 PAN SCAN 79
48kHz/96kHz PCM 85
5.1 Channel Surround 22
Program Play 41
DOLBY DIGITAL 56, 84
Q
DOWNMIX 84
DTS 56, 85
QUICK 78
Quick Setup 28
DVD 33, 92
A
DVD-RW 37, 92
A-B Repeat Play 45
ADVANCED 55
ALL DISCS 40
R
F
Remote 15
Fast forward 34
Fast reverse 34
Front Panel Display 9
REPEAT 44
Repeat Play 44
Replay 34
RESET 78
Resume Play 36
ANGLE 63
ANGLE VIEWER 50
AUDIO 56, 78
AUDIO ATT 83
AUDIO DRC 83
AUDIO FILTER 83
AUDIO SETUP 83
AUTO PLAY 81
H
Handling discs 7
Hooking up 18
S
S VIDEO output 18
SACD 93
I
B
INDEX 48
Index 93
SCENE 48
Scene 93
BACKGROUND 80
BALANCE 88
Batteries 15
SCREEN SAVER 80
SCREEN SETUP 79
Searching. See Locating.
SETUP 77
Setup Display 77
SHUFFLE 43
Shuffle Play 43
SIZE 86
Slow-motion Play 47
SPEAKER SETUP 86
Speakers
L
LANGUAGE SETUP 78
LEVEL 88
Locating
a specific point by watching
the TV screen 47
BNR 65
C
CD 33
CD DIRECT 82
CHAPTER 48
Chapter 92
CHAPTER VIEWER 50
Connecting 18
Continuous play
DVD 33
SACD/CD/VIDEO CD 33
Control Menu 12
CUSTOM 77
CUSTOM PARENTAL
CONTROL 68
CUSTOM SETUP 81
M
MENU 78
Menu
disc’s menu 37
top menu 37
MULTI/2CH 38
Hooking 22
STROBE PLAYBACK 50
SUBTITLE 64, 78
Subtitles 64
SURROUND 58
O
ONE DISC 40
T
On-screen display
Control Menu display 12
Setup Display 77
ORIGINAL 37
ORIGINAL/PLAY LIST 37
OSD 78
TEST TONE 88
Time search 49
TIME/TEXT 48
TITLE 48
Title 93
TITLE VIEWER 50
Top menu 37
TRACK 48
Track 94
TRACK SELECTION 82
TRACK VIEWER 50
continued
D
DCS (Digital Cinema Sound)
92
DIGITAL OUT 84
Digital output 84
DIGITAL VIDEO
ENHANCER 67
DIMMER 81
P
PARENTAL CONTROL 69
PAUSE MODE 81
PBC Playback 39
Display
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting 89
TV TYPE 79
TVS (TV Virtual Surround)
58, 94
U
Usable discs 6
V
VIDEO CD 33
VIDEO EQUALIZER 66
VIEWER 50
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|