WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
3-262-864-21(1)
Precautions
IMPORTANT SAFEGUARDS
For your protection, please read these safety instructions completely before operating the appliance,
and keep this manual for future reference.
• Operate the unit on the power source specified in
the “Specifications.”
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
• The nameplate indicating operating voltage, etc. is
located on the bottom of the unit.
• To disconnect the power cord (mains lead), pull it
out by the plug, not the cord.
• Do not leave the unit in a location near a heat
source, such as a radiator or airduct, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
• Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on a surface (a rug,
blanket, etc.) or near materials (a curtain) that might
block the ventilation holes.
• Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by a qualified
personnel before operating it any further.
• When the casing becomes soiled, clean it with a soft
cloth dampened with mild detergent solution. Never
use abrasive cleansers or chemical solvents, as they
may mar the casing.
Carefully observe all warnings, precautions and instructions on the appliance and in the operating
instructions, and adhere to them.
INSTALLATION
Wa t e r a n d Mo ist u re
Do not use powerline operated appliances near water - for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
He a t
Do not place the appliance near or over a radiator or heat register, or where it is exposed to direct
sunlight.
TV/WEATHER/FM/AM
CD Clock Radio
ICF-CD855V
Operating Instructions
Ve n t ila t io n
The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable
operation of the appliance, and to protect it from overheating, these slots and openings must never be
blocked or covered.
-Never cover the slots and openings with a cloth or other materials.
-Never block the slots and openings by placing the appliance on a bed, sofa, rug or other similar
surface.
-Never place the appliance in a confined space, such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
Acce sso rie s
This symbol is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or an adult, and serious damage to the appliance. Use only a cart,
stand, tripod, bracket, or table recommended by Sony.
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
-An appliance and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
Wa ll o r Ce ilin g Mo u n t in g
If your appliance can be mounted to a wall or ceiling, mount it only as recommended by Sony.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Troubleshooting
USE
Dream Machine is a trademark of Sony Corporation.
Po w e r So u rce
Should any problem occur with the unit, make the
following checks to determine whether or not
servicing is required. If the problem persists, consult
the nearest Sony dealer.
This appliance should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of electrical power supplied to your home, consult your dealer or local
power company. For those appliances designed to operate from battery power, or other sources, refer
to the operating instructions.
Gro u n d in g o r Po la riza t io n
This appliance is equipped with a polarized AC power cord plug (a plug having one blade wider than
the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow
the instructions below:
-Fo r t h e a p p lia n ce w it h a p o la rize d AC p o w e r co rd p lu g :
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized
plug by forcing it in.
-Fo r t h e a p p lia n ce w it h a t h re e -w ire g ro u n d in g t yp e AC p lu g :
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat
the safety purpose of the grounding plug.
Ow n e r’s Re co rd
The clock does not show the correct time.
• Has an electrical power outage lasting more than
one minute occurred?
The CD, radio or buzzer alarm does not
sound at the preset alarm time.
∗ The graphical symbols are at the bottom of the
The model number and the serial number are located on the bottom.
Record the serial number in the space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
unit.
INFORMATION
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
Model No. ICF-CD855V
Serial No.
• Hasn’t all ALARM indicator lights gone out?
The CD or radio alarm is activated but no
sound comes on at the preset alarm time.
• Has VOLUME been adjusted ?
The CD player does not operate.
• Did you close the CD lid?
• Did you place the disc correctly?
The disc should be placed with the labelled
side up.
• Dusty or defective disc — Clean the disc with an
optional cleaning cloth. Wipe the disc from the
center out.
• Take out the CD and leave the CD compartment
open for about an hour to get rid of moisture
condensation.
For customers who purchased this product in the USA
Please register this product on line at
Proper registration will enable us to send you periodic mailings about new products,
services, and other important announcements.
Registering your product will also allow us to contact you in the unlikely event that the
product needs adjustment or modification. Thank you.
Ove rlo a d in g
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since
this can result in fire or electric shock.
Wh e n n o t in u se
Unplug the power cord of the appliance from the outlet when left unused for a long period of time.
To disconnect the cord, pull it out by grasping the plug. Never pull the plug out by the cord.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-
free vegetable oil based ink.
Po w e r-Co rd Pro t e ct io n
Route the power cord so that it is not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to the plugs, receptacles, and the point where the cord exits
from the appliance.
Sporadic loss of sound in CD operation.
• Dusty or defective disc — Clean or replace the disc.
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Lig h t n in g
2004 Sony Corporation
Printed in China
For added protection for this appliance during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the appliance due to lightning and powerline surges.
• Volume too high — Reduce the volume.
• Strong vibration.
No sound comes from the speakers.
• Hasn’t headphones (not supplied) been plugged in?
Disconnect the headphones from the i jack.
Ob je ct a n d Liq u id En t ry
Never push objects of any kind into the appliance through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any
kind on the appliance.
— Consult the dealer or an experienced radio/
TV technician for help.
Cle a n in g
If you have any questions about this product, you may
call:
Sony Customer Information Services Center
1-800-222-7669 or write to:
Sony Customer Information Services Center
12451 Gateway Blvd., Ft Myers, FL 33913
Unplug the appliance from the wall outlet before cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the appliance.
Clean the appliance only as recommended by Sony.
Specifications
AUDIO POWER SPECIFICATIONS
At t a ch m e n t s
Do not use attachments not recommended by Sony, as they may cause hazards.
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 8–ohm loads, both channels driven from
100 – 10 000 Hz; rated 1.0 W per channel-minimum
RMS power, with no more than 10% total harmonic
distortion in AC operation.
ANTENNAS
Declaration of Conformity
Ou t d o o r An t e n n a Gro u n d in g
Trade Name:
Model:
SONY
ICF-CD855V
If an outdoor antenna or cable system is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN
TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM
IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810 of the National Electrical Code provides information with respect
to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
Responsible Party: Sony Electronics Inc.
Address:
680 Kinderkamack Road,
Oradell, NJ 07649 USA
CD player section
System: Compact disc digital audio system
Laser diode properties:
Telephone Number: 201-930-6972
Material: GaAlAs
Wavelength: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
An t e n n a Gro u n d in g Acco rd in g t o t h e Na t io n a l
Ele ct rica l Co d e
the optical pick-up block with 7 mm aperture.)
+1
Frequency response: 20-20 000 Hz –1.5 dB
Wow and flutter: Below measurable limit
Antenna Lead-in Wire
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
Ground
Clamps
Radio section
Frequency range:
Antenna Discharge Unit
(NEC Section 810-20)
TV:
2 – 13 ch
Grounding Conductors
(NEC Section 810-20)
Ground Clamps
Electric Service
Equipment
CAUTION
The use of optical instruments with this
product will increase eye hazard.
WEATHER: 1 – 7 ch
NEC-NATIONAL
ELECTRICAL CODE
FM:
AM:
87.5 – 108 MHz
530 – 1 710 kHz
Power Service Grounding Electrode System
(NEC Art 250 Part H)
SERVICE
General
Da m a g e Re q u irin g Se rvice
Time display: 12-hour system
Speaker: 50 mm (2inches) dia., 8 Ω
Outputs: i (headphones) jack (ø 3.5 mm
stereo minijack)
Unplug the appliance from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
Features
-When the power cord or plug is damage or frayed.
-If liquid has been spilled or objects have fallen into the appliance.
-If the appliance has been exposed to rain or water.
-The appliance does not appear to operate normally or exhibits a marked change in performance.
-This indicates a need for service.
• TV/WEATHER/FM/AM 4 band PLL (phase locked
loop) synthesized clock radio
Power outputs:
1 W + 1 W (at 10% harmonic distortion)
Power requirements: 120 V AC, 60 Hz
Dimensions:
• Easy preset digital tuning with 25 memory presets
• Built-in CD player with CD-R/RW playback
function
-If the appliance does not operate normally when following the operating instructions, adjust only
those controls that are specified in the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive work
by a qualified technician to restore the appliance to normal operation.
-If the appliance has been subject to excessive shock by being dropped, or the cabinet has been
damaged.
Approx. 169 × 165 × 217 mm (w/h/d)
(Approx. 6 3/4 × 6 1/2 × 8 5/8 inches) incl.
projecting parts and controls
• Dual alarm
• Triple time display – main display for the clock, and
two alarm sub-displays
• Nap timer – count down timer (10, 20, 30, 60, 90,
120 minutes)
• Extendable Snooze time from 10 to 60 minutes
• LCD with brightness adjustment backlight (High/
Middle/Low)
Mass: Approx. 1 700 g (3 lb 12oz)
Se rvicin g
Design and specifications are subject to change
without notice.
Do not attempt to service the appliance yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Re p la ce m e n t p a rt s
When replacement parts are required, be sure the service technician has used replacement parts
specified by Sony that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Lead-free solder is used for soldering.
Halogenated flame retardants are not
used in printed wiring boards.
Sa fe t y Ch e ck
Upon completion of any service or repairs to the appliance, ask the service technician to perform
routine safety checks (as specified by Sony) to determine that the appliance is in safe operating
condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
|