Sony Car Video System 26 473 01 User Manual

Sony LCD Compatible Installation  
Configuration and Connections  
SYSTEM 4xi  
PROJECTOR COMMUNICATIONS KIT  
ATTENTION!  
PLEASE READ THIS DOCUMENT FOR IMPORTANT  
INSTALLATION INSTRUCTIONS  
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:  
Kit Type: SONY LCD compatible  
Included Communications Adapter(s):  
Quantity  
Part Number  
26-483-01  
26-473-01  
Description  
ADP, IR COMM  
ADP, UNV, E”  
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING  
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS  
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS  
INDICATED BY THE “” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL  
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER  
WITH THE CORRECT SETTINGS.  
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND  
SIGNAL CONNECTION INSTRUCTIONS.  
THIS SWITCHER HAS BEEN CONFIGURED FOR: SONY LCD VPL-X600 or  
SONY VPL-X2000U  
Config  
as  
MODEL  
SW1  
SW2 SW3 SW4 SW5 SW6 PROJ  
CABLE  
COMM  
ADAPTER  
1
2
3
4
Sony VPL-X600  
Sony VPL-X2000U off on off on  
Sony RS-232 off on off on  
off on off on  
0
0
0
0
0
0
3
3
8
5
5
E
1
1
0
J15  
J15  
J15  
26-483-01  
26-483-01  
26-473-01  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony LCD Compatible Installation  
Configuration and Connections  
5. Verify that the IR Comm Adapter is configured correctly (refer to the IR Comm  
Adapter User’s Guide). Connect the 3.5 mm male plug end of the supplied  
cable into the “OUT” jack of the IR Comm Adapter. Connect the other end of the  
cable into the “CONTROL S IN” port of the projector. If a hardwired remote or  
host controller is being implemented, connect that device to the “IN” jack of the  
IR Comm Adapter.  
6. Plug the 15-pin HD connector of the Projector Communications Extension cable  
into the PJ Comm port on the System 4xi. Connect the other end of the cable  
into the IR Comm Adapter’s “PROJECTOR CONTROL” port.  
______ Secure all of the connector screws.  
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV  
cable into the System 4xi output Connect the 15-pin male end of the RGBS/HV  
cable into “INPUT A” of the projector.  
Use the illustration below as a guide when connecting the System 4xi to a Sony  
LCD projector. Refer to Sony documentation to continue the installation.  
Hardwired remote/  
host controller  
Cable  
26-485-01  
IR Comm Adapter  
26-483-01  
Female  
9-pin  
15-pin  
CC 50'  
15-pin  
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the  
System 4xi. See page 2-5 for cabling guidelines.  
Page 2  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony LCD Compatible Installation  
Configuration and Connections  
Connecting System 4xi to Sony VPL-X2000U  
If the System 4xi is already configured for a Sony LCD VPL-X2000U projector,  
go to step 4. If it is not set up correctly, it will be necessary to change switch  
settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the  
correct configuration.  
1. Use the Front Panel to display the Information Menu to verify that the System 4xi  
is already set up for the Sony LCD projector. Apply power to the System 4xi and  
do the following:  
a. Press  
b. Press  
c. Press  
d. Press  
to display the MENU SELECT on the LCD screen.  
to step to Menu 8.  
or  
to select this menu.  
[System 4 model and software  
version displayed here]  
or  
to display the configuration. The example to the left is general,  
yours will show the System 4xi model name, the software version and the  
following information:  
PRJ = SONY  
PRJ BAUD = 9600  
UNIT No. = 000  
HST BAUD = 9600 (value depends upon setup Menu 3)  
(See note.)  
(See note.)  
(See note.)  
(See note.)  
}
(Note: Information depends on  
System 4 setup.)  
2. Go to the procedure on page 2-3 of the System 4xi User’s Manual to remove the  
System 4xi cover. Then go to page 2-4 and refer to the configuration below to  
set up the Main Controller board. Continue with Step 3 (below) when the  
configuration is correct.  
SW2 SW3 SW4 SW5 SW6  
SW1  
Config  
PROJ  
CABLE  
Comm  
Adapter  
Model  
as  
1 2 3 4  
off on off on  
0
0
Sony LCD VPL-X2000U  
3
5
1
J15  
83  
26-4 -01  
SW3  
SW2  
SW5  
SW6  
J15  
SW4  
SW1  
4
3
2
1
ON  
3. Double-check your work and be sure the System 4xi cover is on securely.  
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.  
__________ Changes in some switch configurations are not detected until the power is  
removed at the AC cord, and then restored.  
Refer to the following connection diagram and continue.  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony LCD Compatible Installation  
Configuration and Connections  
5. Verify that the IR Comm Adapter is configured correctly (refer to the IR Comm  
Adapter User’s Guide). Connect the 3.5 mm male plug end of the supplied  
cable into the “OUT” jack of the IR Comm Adapter. Connect the other end of the  
cable into the “CONTROL S IN” port of the projector. If a hardwired remote or  
host controller is being implemented, connect that device to the “IN” jack of the  
IR Comm Adapter.  
6. Plug the 15-pin HD connector of the Projector Communications Extension cable  
into the PJ Comm port on the System 4xi. Connect the other end of the cable  
into the IR Comm Adapter’s “PROJECTOR CONTROL” port.  
______ Secure all of the connector screws.  
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV  
cable into the System 4xi output Connect the other end of the cable into the  
“INPUT A” BNC connectors of the projector.  
Use the illustration below as a guide when connecting the System 4xi to a Sony  
X2000U projector. Refer to Sony documentation to continue the installation.  
Hardwired remote/  
host controller  
IR Comm Adapter  
26-483-01  
Cable  
26-485-01  
Female  
9-pin  
CC 50'  
15-pin  
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the  
System 4xi. See page 2-5 for cabling guidelines.  
Page 4  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony LCD Compatible Installation  
Configuration and Connections  
Connecting System 4xi to Sony Projector under RS-232 Control  
If the System 4xi is already configured for a Sony RS-232 projector, go to step  
4. If it is not set up correctly, it will be necessary to change switch settings on the  
System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct  
configuration.  
1. Use the Front Panel to display the Information Menu to verify that the System 4xi  
is already set up for the Sony RS-232 projector. Apply power to the System 4xi  
and do the following:  
a. Press  
b. Press  
c. Press  
d. Press  
to display the MENU SELECT on the LCD screen.  
to step to Menu 8.  
or  
to select this menu.  
[System 4 model and software  
version displayed here]  
or  
to display the configuration. The example to the left is general,  
yours will show the System 4xi model name, the software version and the  
following information:  
PRJ = SONY  
PRJ BAUD = 38400  
UNIT No. = 000  
HST BAUD = 9600 (value depends upon setup Menu 3)  
(See note.)  
(See note.)  
(See note.)  
(See note.)  
}
(Note: Information depends on  
System 4 setup.)  
2. Go to the procedure on page 2-3 of the System 4xi User’s Manual to remove the  
System 4xi cover. Then go to page 2-4 and refer to the configuration below to  
set up the Main Controller board. Continue with Step 3 (below) when the  
configuration is correct.  
SW1  
SW2 SW3 SW4 SW5 SW6  
Config  
as  
PROJ  
CABLE  
Comm  
Adapter  
Model  
1 2 3 4  
off on off on  
Sony RS-232  
0
0
8
E
0
J15  
26-473-01  
SW3  
SW2  
SW5  
SW6  
J15  
SW4  
SW1  
4
3
2
1
ON  
3. Double-check your work and be sure the System 4xi cover is on securely.  
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.  
__________ Changes in some switch configurations are not detected until the power is  
removed at the AC cord, and then restored.  
Refer to the following connection diagram and continue.  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony LCD Compatible Installation  
Configuration and Connections  
5. Connect the Comm Adapter to the “RS-232C/422A” port on the projector.  
6. Connect the CC-50’ or (CC-100’) cable from the 9-pin male connector of the  
Comm Adapter to the 15-pin HD “PJ COMM” port on the rear panel of the  
System 4xi.  
______ Secure all of the connector screws.  
7. Ensure the projector’s RS-232C/RS-422A switch is in the RS-232C position.  
8. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV  
cable into the System 4xi output Connect the other end of the cable into the  
“INPUT A” BNC connectors of the projector.  
Use the illustration below as a guide when connecting the System 4xi to a Sony  
RS-232 projector. Refer to Sony documentation to continue the installation.  
0
1
9-pin  
Male  
Male  
Comm Adapter  
26-473-01  
E
9-pin  
Female  
CC 50'  
15-pin  
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the  
System 4xi. See page 2-5 for cabling guidelines.  
____________ Ensure the projector’s INDEX and PERIPHERAL dials are set to 01.  
Page 6  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-428-02 Rev. C  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Wireless Office Headset PG185 User Manual
Sony Battery Charger BC VM50 User Manual
Sony Digital Camera 4 143 374 111 User Manual
Sony MP3 Player ZS D5 User Manual
Sony Stereo System CMT DX400A User Manual
Sony Stereo System TC WE635 User Manual
Sony Universal Remote AIR RM10 User Manual
State Industries Water Heater SBN71120NE User Manual
Sub Zero Refrigerator IC 27FI User Manual
Tanaka Automobile Parts TC 355 User Manual