3-866-256-11(1)
Stereo
Cassette Deck
Operating Instructions
TC-WE835S
TC-WE635
1999 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Getting Started
Unpacking 4
Hooking Up the System 4
Playing a Tape 5
Recording on a Tape 6
Advanced Playback Operations
Locating a Track (Multi-AMS/ Auto Play/ Memory Play) 8
Creating Your Own Program (RMS Play) 9
Advanced Recording Operations
Adjusting Bias and Recording Level Calibration Automatically 11
Adjusting the Recording Level Automatically (Auto Rec Level) 12
Fading In and Out (Fader) 13
Dubbing a Tape 13
Recording on Both Decks in Succession (Relay Recording) 14
Recording the Same Source on Both Decks (Simultaneous Recording) 15
Recording Your Own Program (RMS Dubbing) 15
Inserting a Blank Space During Recording (Record Muting) 16
Synchro-recording With a CD Player Through a Control A1 Cord 16
Synchro-recording With a CD Player Using a Remote 17
Additional Information
Precautions 18
Notes on Cassette Tapes 18
Cleaning 19
Troubleshooting 20
Specifications 21
Glossary 22
Index 22
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
Hookups
Unpacking
• Connecting the tape deck to an amplifier
Connect the amplifier to the LINE IN/ OUT connectors
using the supplied audio connecting cords.
When connecting an audio connecting cord, be sure to
match the color-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to White.
Be sure to make connections firmly to avoid hum and
noise.
Check that you received the following items:
• Audio connecting cords (2)
• Remote commander (remote) RM-J910 (1)*
• Sony R6 (size AA) batteries (2)*
• Control A1 cord (1)**
* Supplied for TC-WE835S U.S.A. model only
** Supplied for Canadian models only
Tape deck
Amplifier
Ç
LINE
TAPE
Inserting batteries into the remote
(TC-WE835S U.S.A. model only)
IN OUT
REC OUT
IN
L
L
L
Insert two R6 (size-AA) batteries, matching the + and –
on the batteries with the markings inside the battery
compartment. When using the remote, point it at the
remote control sensor g on the tape deck.
R
R
R
ç
ç: Signal flow
• Connecting the tape deck to a CD player equipped
with CONTROL A1 connectors
For information on connections through the CONTROL
A1 connectors, refer to the pamphlet included with this
manual.
Setting the voltage selector (only on
models supplied with a voltage selector)
Check that the voltage selector on the rear panel of the
tape deck is set to the local power line voltage. If not,
set the selector to the correct position using a
screwdriver before connecting the AC power cord to
an AC outlet.
Hooking Up the System
This section describes how to hook up the tape deck to
an amplifier or a CD player equipped with CONTROL
A1 connectors. Be sure to turn off the power of each
component before making the connections.
VOLTAGE
220V
230
–
Tape deck
240V
120V
to an AC
outlet
Connecting the AC power cord
Connect the AC power cord to an AC outlet.
REC
OUT
TAPE
IN
Amplifier
Where do I go next?
Now you’re ready to use your tape deck.
to a
For basic operations, go to pages 5 to 7; for advanced
operations, go to the sections starting from page 8.
w all outlet
CONTROL
A1
CD player
ç: Signal flow
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sic Op e ra t io n s
Pla yin g a Ta p e
3 2
4
RESET
MEMORY
A
COUNTER
B
RESET
MEMORY
AUTO REC LEVEL
5
4
6
•
•
3
1
7
U
2
8
9
•
•
(
)
10
RMS
AUTO CAL START P
DUBBING
REC HIGH/NORMAL
START (DECK B P)
AnB
0
DIRECTION MODE
RMS/START
SET
CHECK
DISPLAY
DECK
A
DECK
B
A+B
A
a
RELAY
–
)
RMS
+
(
FADER
ARL
(
)
(
)
(
)
0
AMS
AMS
)
0
AMS
AMS
)
Ø
ON
ø
OFF
SYNCHRO
p
p
ª
·
ª
·
PITCH CONTROL
CLEAR
BACK
FRONT
PHONES
•
DOLBY NR
OFF ON ON FILTER
PAUSE REC MUTING
REC
PAUSE REC MUTING
REC
B
C
S
P
R
r
P
R
r
–
+
§
§
• See page 4 for hookup
information.
• You can use either deck for
playback.
Turn on the amplifier and select the tape deck position.
1
2
Press U(or 1/u), and press §fully to
open the cassette holder, then insert a
cassette.
zTo adjust the pitch (Pitch
With the side you w ant to play
facing you
Control function)
OFF
ø
ON
Ø
PITCH CONTROL
Set DIRECTION MODE.
+
3
–
To play back
Set to
A
Push in the PITCH
CONTROL button to activate
the Pitch Control function
and turn the control
One side only
Both sides continuously*
Both decks in succession*
a
clockwise to raise the pitch or
counterclockwise to lower it.
You can adjust the pitch
during playback on deck A
or normal-speed dubbing
(but not during RMS play or
RMS dubbing).
RELAY
* The deck automatically stops after playing back five times.
Press ·.
4
The deck starts playing. Adjust the volume on the amplifier.
Do not press U(or 1/u) or §w hile the tape deck is
operating. If you do so, the tape may be damaged.
zTo play a tape recorded
with the Dolby* NR
Set DOLBY NR to ON and
select the same position that
the tape was recorded in—B,
C, or S (TC-WE835S only).
To
Press
Stop playing
p
zYou can connect the
headphones to the PHONES
jack
Start playback from the reverse side
Pause
ª
PAUSE P. Press the button again to resume
play.
Fast-forward or rewind
)or 0when the deck is stopped
Increase the tape fast-forward or rewind )or 0again during fast-forwarding or
* “DOLBY”, the double-D
symbol a and “HX Pro” are
trademarks of Dolby
Laboratories Licensing
Corporation.
speed (High-speed Fast-forwarding and
rewinding
Rewinding functions) (TC-WE835S only)
Take out the cassette
§after stopping playing
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sic Op e ra t io n s
Re co rd in g o n a Ta p e
3 2
5
4
RESET
MEMORY
A
COUNTER
B
RESET
MEMORY
AUTO REC LEVEL
5
4
6
•
•
3
7
9
U
2
8
1
•
•
(
)
10
RMS
AUTO CAL START P
DUBBING
REC HIGH/NORMAL
START (DECK B P)
AnB
0
DIRECTION MODE
RMS/START
SET
CHECK
+
DISPLAY
DECK
A
DECK
B
A+B
A
a
RELAY
–
RMS
FADER
ARL
(
)
(
)
(
)
(
)
0
AMS
AMS
)
0
AMS
AMS
)
Ø
ON
ø
OFF
SYNCHRO
PHONES
p
p
ª
·
ª
·
PITCH CONTROL
CLEAR
BACK
FRONT
•
DOLBY NR
OFF ON ON FILTER
PAUSE REC MUTING
REC
PAUSE REC MUTING
REC
B
C
S
P
R
r
P
R
r
–
+
§
§
• See page 4 for hookup
information.
• You can use either deck for
recording.
• See “Dubbing a Tape”
(page 13) to make a copy
of the tape.
Turn on the amplifier and play the program source you want to
record.
1
2
Press U(or 1/u), and press §fully to
open the cassette holder, then insert a
cassette.
With the side you w ant to
record facing you
zTo check the approximate
remaining time on a tape
(TC-WE835S only)
1 Locate the end of the
recorded portion on the
tape and press RESET for
the deck you’re using to
reset the tape counter to
“0.00”.
Set DIRECTION MODE.
3
4
To record on
Only one side
Both sides*
Set to
A
a
2 Press )to fast-forward
the tape to its end. The
tape counter shows the
approximate remaining
time.
* Recording stops when the tape reaches the end of reverse side.
Press REC r.
·lights up for recording on the side facing you. If it doesn’t,
press ·once.
Note
Since the counter is not a
digital clock, the displayed
value will differ slightly from
the actual elapsed recording
or playing time.
The tape deck automatically adjusts the recording level (see
page 12). After the AUTO indicator lights up continuously,
stop playing the program source. If you wish to adjust the
recording level manually, see “To adjust the recording level
manually” on page 7.
Do not press U(or 1/u) or §w hile the tape deck is
operating. If you do so, the tape may be damaged.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sic Op e ra t io n s
zTo protect recordings
against accidental erasure
Break out the record-protect
tab(s) (see page 18).
Press PAUSE Por ·.
5
6
Recording starts.
Start playing the program source.
To
Press
Stop recording
p
Start recording from the reverse side
Pause
ª
twice in Step 5
PAUSE P. Press the button again to
resume recording.
Take out the cassette
§after stopping recording
zThe Dolby HX Pro*
automatically works during
recording
Use the following selectors and control to perform additional
operations
Distortion and noise in the
high-frequency response are
reduced to produce high-
quality sound that can be
enjoyed even during
MORY
A
COUNTER
B
RESET
MEMORY
AUTO REC LEVEL
5
4
6
•
•
3
1
7
9
2
8
•
•
(
)
10
RMS
AUTO CAL START P
DUBBING
REC HIGH/NORMAL
START (DECK B P)
AnB
0
ET
CHECK
+
DISPLAY
DECK
A
DECK
B
A+B
–
RMS
playback on other tape decks.
FADER
ARL
(
)
(
)
(
)
AMS
)
0
AMS
AMS
)
SYNCHRO
p
ª
·
ª
·
BACK
FRONT
PHONES
DOLBY NR
OFF ON ON FILTER
TING
REC
PAUSE REC MUTING
REC
B
C
S
r
P
R
r
§
DOLBY NR
REC LEVEL
To record with the Dolby NR
Set DOLBY NR to ON, and select B, C, or S (TC-WE835S only) before you start
recording.
To record FM broadcasts with the Dolby NR
If the FM reception is unsatisfactory, set DOLBY NR to ON FILTER (multiplex
filter) (see page 22).
Note
Even after adjusting the recording
level, distortion may occur
depending on the source that
you’re recording from. If this
happens, turn REC LEVEL
counterclockwise to lower the
level.
To adjust the recording level manually
0
+
4
+
8
–
∞
–30 –20
–10
–4
a
dB
L
After pressing REC rin Step 4 on page 6, turn
REC LEVEL so that the peak level meters reach
the recommended level for the corresponding
tape type. After completing the adjustments, stop
playing the program source, then continue the
procedure from Step 5.
R
For type I or
type II tape
For type IV tape
* HX Pro headroom extension
originated by Bang & Olufsen
and manufactured under
license from Dolby Laboratories
Licensing Corporation.
“DOLBY”, the double-D
symbol a and “HX Pro” are
trademarks of Dolby
Laboratories Licensing
Corporation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Pla yb a ck Op e ra t io n s
Notes
•
The Multi-AMS function may not work correctly if:
Locating a Track (Multi-AMS/
Auto Play/Memory Play)
— the blank space between tracks is less than 4 seconds
long.
— there is a passage of low frequencies or very low
volume within a track.
You can locate the following/ previous tracks within a
range of 30 tracks (Multi-AMS: Automatic Music
Sensor) or the beginning of a tape quickly (Auto Play).
You can even locate a specific point anywhere on a
tape (Memory Play).
— the signal strength of the left and right channels are
very different.
•
•
•
The Multi-AMS function is inoperative on a deck
whenever the other deck is playing, recording (except
during dubbing), or in pause.
Even if the DIRECTION MODE selector is set to a, the
deck stops when the current side reaches the end during
Multi-AMS operation.
MEMORY
RESET
MEMORY
RESET
The tape counters are reset to “0.00” (TC-WE835S only) or
to “0000” (TC-WE635 only) when you turn off the tape
deck.
U
0
p
)
0
)
p
ª
·
ª
·
•
P
R
r
P
R
r
§
§
0/)
ª/·
0/)
Note
Check the direction indicator of the deck you use. When you
locate a track on the reverse side (when ª lights up), press
the button(s) in the parentheses.
To locate
Press
The beginning of the
next or succeeding
tracks
) (or 0) as many times as you
want during playback.
For example, to locate 2 tracks
ahead, press twice.
(Multi-AMS)
The beginning of the
current track
0 (or )) once during playback.
(Multi-AMS)
The beginning of the
preceding tracks
(Multi-AMS)
0 (or )) as many times as you
want during playback.
For example, to locate 2 tracks
behind, press three times.
The beginning of a tape MEMORY on the deck being used
(Auto Play)
repeatedly until “M” disappears in
the display. Then press 0 (or ))
while holding down · (or ª).
A particular point on a MEMORY on the deck being used
tape (Memory Play)
repeatedly until “M” appears in the
display. Find the point you want,
then press RESET to reset the tape
counter and to memorize the point.
To locate the memorized point and
start playback, press 0 (or ))
while holding down · (or ª).
(Press 0 or ) to stop at “0.00”
(TC-WE835S only) or at “0000” (TC-
WE635 only). )
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Pla yb a ck Op e ra t io n s
5
6
Repeat Steps 2 to 4 to program more tracks.
Creating Your Own Program
(RMS Play)
If “FULL” appears in the display
This means that you’ve already programmed 28 tracks
and can’t program any more.
By creating a program, you can play back tracks on
deck A in any order that you want. The Random
Music Sensor (RMS) function lets you create a program
of up to 28 tracks, from the 1st to the 14th tracks on
each side of the tape.
Press RMS/ START to start RMS Play.
The peak level meters appear in the display.
To stop RMS Play
Press p (CLEAR) once. The RMS program still
RMS buttons (RMS/START, SET, CHECK, DISPLAY)
remains.
U
To cancel RMS Play
Press p (CLEAR) repeatedly until the peak level
meters appear in the display or eject the tape in deck A.
When RMS Play is canceled, the RMS program is
automatically erased.
0
p
)
0
p
)
ª
·
ª
·
•
P
R
r
P
R
r
§
§
0/)
p
ª/·
To alternate between the RMS and peak level meter
displays
Press DISPLAY.
1
2
3
Press RMS/ START.
“RMS” and a flashing cursor appear in the
display.
z You can play the program again after RMS Play ends
Press ª (BACK) or · (FRONT) to select the
side of the tape.
ª or · appears in the display.
Press RMS/ START.
Notes
•
During RMS Play, you can only use the CHECK,
DISPLAY, and p buttons on deck A, and the p, 0, and
) buttons on deck B.
Press 0 or ) repeatedly until the track
number you want appears in the display.
•
•
•
The RMS function may not work properly if a blank space
between tracks is short.
·
0 3
If there is a long blank space between tracks, the deck may
fast-forward a portion of the blank space.
FRONT
RMS
1
2
3
4
5
6
7
8
9
10 11 12 13 14
If your program includes a number for a track that does
not exist, the deck will skip that number during RMS Play.
BACK
Side of the cassette
Track number
Checking the order of tracks in the
program
4
Press SET to store your selection.
To program the same track again, press SET once
more.
Press CHECK.
Each time you press this button, the display shows the
track numbers in the order they were programmed.
After the last track in the program, “End” appears in
the display.
·
1 3
FRONT
RMS
1
2
3
4
5
6
7
8
9
10 11 12 13 14
BACK
Track number
Order on the program
(Continued)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Pla yb a ck Op e ra t io n s
Adding tracks to the end of a program
Press p (CLEAR) once, and follow Steps 2 to 5 in
“Creating Your Own Program (RMS Play)” on page 9.
z To create another program
Press p (CLEAR) until the order on the program
returns to 0 and the cursor flashes above track number 1
in the display, then follow Steps 2 to 5 on page 9.
z You can use your Sony remote to perform RMS
programming
If your Sony stereo receiver’s remote has RMS buttons,
do the following steps.
1 Turn on the receiver and press TAPE.
2 Press RMS/ START.
3 Press · or ª to select the front or reverse side of
the tape, and the number keys and the >10 key to
specify the tracks.
4 Press RMS/ START again to start RMS Play.
Note
For more information on the availability of Sony stereo
receiver remotes with RMS capability, contact your
nearest Sony dealer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
4
Press PAUSE P.
The automatic calibration procedure starts (i.e.,
Adjusting Bias and Recording
Level Calibration
Automatically
recording test tones, rewinding, and playing
back).
During the calibration, the counter changes from
9 to 0.
Since there are many different types of cassettes on the
market, your tape deck automatically sets the
appropriate equalization characteristics and bias
current for each tape type (ATS: Automatic Tape
Selection). However, you can get better recording
results by doing the automatic bias current and the
recording level calibration.
CAL
B
REC
CA.L9
When the automatic calibration procedure ends,
the tape rewinds to the original position, the
counter returns to normal and the tape deck stops.
ª/·
DECK A/DECK B
5
Start the actual recording (see page 6).
U
To cancel the Automatic Calibration function
0
p
)
0
p
)
ª
·
ª
·
•
Press p on the deck you’re using.
P
R
r
P
R
r
§
§
If “A” or “B” flashes continuously
The automatic calibration procedure has been
interrupted by:
• The end of the tape. Reverse the tape direction or
rewind the tape to a new position that allows
recording of the test tone.
ª/·
PAUSE P
1
Insert the cassette you want to record on into
either deck.
Make sure the record-protect tabs on the cassette
have not been removed.
• Damaged tape or dirty heads. Change the cassette or
clean and demagnetize the heads (see page 19).
2
3
Press DECK A or DECK B until “CAL” appears in
the display.
Updating the calibration setting
Press · or ª to select the side of the tape to be
If you insert a cassette and “[A] CAL” or “CAL [B]”
appears in the display, it means that automatic
calibration data in that deck for that tape type (I, II or
IV) exists. However, we recommend that you repeat
the automatic calibration procedure each time you
insert a new cassette since cassettes of the same type
also vary in their characteristics.
recorded.
To select
Press
·
The front side
The reverse side
ª
Before recalibrating, be sure to turn off “[A] CAL” or
“CAL [B]” by pressing the DECK A or DECK B button.
Then start from Step 2 of the automatic calibration
procedure.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
z You should adjust the recording level manually with
the REC LEVEL control in the following cases:
Adjusting the Recording Level
Automatically (Auto Rec Level)
•
The recording level cannot be adjusted properly due
to excessive noise in the program source.
•
The program source level is too low and the
recording level does not increase.
The Auto Rec Level function automatically measures
the peak signal level and adjusts the recording level
accordingly. The Auto Rec Level function operates
during normal recording, Relay Recording or
Simultaneous Recording on either deck.
During a quiet passage in a program source such as
classical music, the recording level may not increase
for some time. If a high sound level is expected later
on in the track, play that portion first so that the right
adjustment can be obtained.
•
The recording level does not decrease for a long time.
The Auto Rec Level function may not work properly
when you try to record sound produced by a graphic
equalizer that has extremely high-level signals.
AUTO indicator
REC LEVEL
U
0
p
)
0
p
)
ª
·
ª
·
•
z To record with the optimum recording level
P
R
r
P
R
r
§
§
•
To prevent changes in the recording level after
recording starts, press REC r while playing the
highest sound level portion of the program source to
be recorded. The result is a more natural-sounding
recording.
p
PAUSE P REC r
·
ARL
1
2
Follow Steps 1 to 3 of “Recording on a Tape” on
page 6.
Make sure that record-protect tabs on the cassette
have not been removed.
•
If you play the entire program source after the AUTO
indicator has stopped flashing and is lit continuously,
the deck will set the recording level for the portion of
the program source with the highest signal level.
Press REC r.
z Recording level setting remains even after the
recording has ended
The AUTO indicator flashes and the deck
automatically adjusts the recording level. The
AUTO indicator lights up continuously after the
recording level has been adjusted.
After you have finished recording with the Auto Rec
Level function, the AUTO indicator remains on and the
recording level setting remains the same. To cancel the
setting, do one of the following:
3
Press PAUSE P or ·.
Recording starts.
•
•
•
Press ARL to turn off the AUTO indicator
Turn REC LEVEL
Turn the deck off.
To cancel the Auto Rec Level function
Press ARL or turn REC LEVEL to turn off the AUTO
indicator. If you do either of these during recording,
recording will continue but with the Auto Rec Level
function turned off.
To stop recording
Press p.
z How the Auto Rec Level function adjusts the
recording level
While the AUTO indicator is flashing, the deck sets the
recording level as high as possible without causing
distortion. If the signal level rises excessively after the
start of recording, the deck gradually decreases the
recording level.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
Fading In and Out (Fader)
Dubbing a Tape
You can gradually increase the recording level at the
beginning of a recording (fade in) or gradually
decrease the recording level at the end of a recording
(fade out).
You can copy a tape in deck A to a tape in deck B at
normal or high speed.
DIRECTION MODE
ª/· HIGH/NORMAL
It is convenient to use this function, for example, when
the tape reaches to its end and you don’t want the track
to be cut off abruptly.
U
0
p
)
0
p
)
AUTO indicator
ª
·
ª
·
•
P
R
r
P
R
r
§
§
U
p
PAUSE P
0
p
)
0
p
)
ª
·
ª
·
•
P
R
r
P
R
r
1
2
Insert a recorded cassette into deck A and a blank
cassette into deck B.
Make sure the record-protect tabs on the cassette
in deck B have not been removed.
§
§
FADER
To
Do the following:
Select the side(s) to be recorded on.
Fade in
1 Follow Steps 1 to 4 of “Recording on a
Tape” on page 6.
To record on
One side
Set DIRECTION MODE to
A
2
Start playing the program source and
press FADER at the point where you
want the fade-in to start. During fade-
in, the AUTO indicator flashes. When
the fade-in has completed, the AUTO
indicator lights up if the Auto Rec
Level function is working, or goes off
if the Auto Rec Level function is not
working.
Both sides
a.
Recording on the reverse side on
deck B starts independently of
playback on deck A.
RELAY.
Recording on the reverse side on
deck B starts simultaneously with
playback of the reverse side on
deck A.
Fade out
While you’re still recording, press
FADER at the point where you want the
fade-out to start. When the fade-out has
completed, “REC” flashes in the display
and the deck pauses.
3
Select the dubbing speed.
To select
Press HIGH/NORMAL
Normal speed
High speed
Once
Note
Fade-in or fade-out is not possible when the REC LEVEL
Twice
control is manually set to 0 (minimum) (see page 7).
“HIGH” or “NORM” appears in the display.
The deck changes to dubbing standby.
4
5
Select the side from which to start dubbing.
To record from
The front side
Press
·
The reverse side
ª
Press PAUSE P on deck B to start dubbing.
(Continued)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
To stop dubbing
Recording on Both Decks in
Succession (Relay Recording)
During
Press
Normal-speed dubbing
High-speed dubbing
p on deck B
p on either deck
You can make a continuous recording that starts on a
cassette in deck A and ends on a cassette in deck B.
z During high-speed dubbing
DIRECTION MODE
ª/·
Only the p button is operative.
z You don‘t have to adjust the recording level or
select the Dolby NR during dubbing
U
0
)
0
p
)
Dubbing is automatically performed with the same
recording level and Dolby NR as the original in deck A.
If, however, you want to monitor the sound during
normal-speed dubbing, set the DOLBY NR selector to
match the tape in deck A (see page 5).
p
ª
·
ª
·
•
P
R
r
P
R
r
§
§
REC r
1
Insert blank cassettes into both decks.
Make sure that record-protect tabs on the
cassettes have not been removed.
z You can adjust the pitch of the playback on deck A
See page 5.
Note
2
3
4
Select the Dolby NR (see page 7).
Set DIRECTION MODE to RELAY.
If a TV set is placed near the tape deck, noise may occur
during high-speed dubbing. In that case, turn the television
set off or move it away from the tape deck.
Press REC r on deck A.
Deck A changes to recording pause.
Dubbing only specific portions
You can do this only during the normal-speed
dubbing.
5
6
Start playing the program source.
Adjust the recording level manually, if necessary
(see page 7).
1
Press p on deck A at the portion you want to
skip.
Deck B changes to recording pause.
7
Start recording.
To record from
The front side
Press
2
3
Locate the point you want to resume recording on
deck A, then stop the tape.
· on deck A
ª on deck A
The reverse side
Press PAUSE P on deck B to resume dubbing.
To stop Relay Recording
During
Press
Recording on deck A
Recording on deck B
p on deck A
p on deck B
Note
Make sure that · on deck B appears in the display. If it
doesn’t, press · on deck B once; otherwise, Relay
Recording stops when the reverse side of the cassette in deck
B finishes.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
Recording the Same Source on
Both Decks (Simultaneous
Recording)
Recording Your Own Program
(RMS Dubbing)
You can record an RMS program that you’ve created
(see “Creating Your Own Program (RMS Play)” on
page 9). This function works only at normal speed.
You can record the same source on cassettes in deck A
and B at the same time.
RMS/START
HIGH/NORMAL
DIRECTION MODE
ª/·
A+B REC
U
U
0
p
)
0
p
)
0
)
0
p
)
ª
·
ª
·
r
•
p
ª
·
ª
·
r
•
P
R
r
P
R
P
R
r
P
R
§
§
§
§
PAUSE P ª/·
PAUSE P ª/·
1
Insert blank cassettes into both decks.
Make sure that record-protect tabs on the cassettes
have not been removed.
1
Insert a recorded cassette into deck A and a blank
cassette into deck B.
Make sure the record-protect tabs on the cassette in
deck B have not been removed.
2
3
Select the Dolby NR (see page 7).
Select the side(s) to be recorded on.
2
3
4
Program tracks on deck A (see Steps 1 to 5 on
page 9).
To record on
Only one side
Both sides
Set DIRECTION MODE to
Press HIGH/ NORMAL once to change the tape
deck to dubbing standby.
A
a
Select the side of the tape in deck B you want to
record on.
4
Press A+B REC.
Both decks change to recording pause.
To start recording
On the front side
On the reverse side
Press
·
5
6
Start playing the program source.
ª
Adjust the recording level manually, if necessary
(see page 7).
5
Press RMS/ START or PAUSE P on deck B to start
RMS Dubbing.
7
Select the side you want to start recording from
on both decks.
To stop RMS Dubbing
Press p on deck B. The RMS program remains even
after RMS Dubbing stops.
To record from
The front side
Press
·
The reverse side
ª
z To insert a blank space on the tape before you start
RMS Dubbing
You can insert a blank space of 4 seconds or more on the
tape in deck B by pressing the REC MUTING R button
after Step 4.
8
Press PAUSE P on deck B.
Simultaneous Recording starts.
For details, see “Inserting a Blank Space During
Recording (Record Muting)” on page 16.
To stop Simultaneous Recording
Press p on both decks.
z A blank of 10 seconds is automatically inserted on
z The PAUSE P and REC MUTING R (see page 16)
buttons on deck B can control both decks at the
same time
the tape when you start RMS Dubbing if:
•
you insert a new cassette into deck B.
the tape in deck B is completely rewound to its
beginning and automatically stopped.
•
During Simultaneous Recording, the PAUSE P and
REC MUTING R buttons on deck B control both decks,
but not the PAUSE P and REC MUTING R buttons on
deck A.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
Inserting a Blank Space During
Recording (Record Muting)
Synchro-recording With a CD
Player Through a Control A1
Cord
You can insert a blank space of 4 seconds between the
tracks. The blank spaces allow you to locate the start of
specific tracks afterwards using the Multi-AMS
function (see page 8). You can also use this function to
erase unwanted portions on a tape.
By pressing the SYNCHRO button, you can perform
synchro-recording on your tape deck with a Sony CD
player connected to the CONTROL A1 connector
through a Control A1 cord (see page 4). The Control
A1 cord supports advanced functions not possible with
the commander-based CD synchro-recording function
on previous models. Further information on the
various operations made possible by a Control A1 cord
is provided in the pamphlet attached to this manual.
PAUSE P
U
0
p
)
0
p
)
ª
·
ª
·
•
P
R
r
P
R
r
§
§
U
0
p
)
0
p
)
REC MUTING R
ª
·
ª
·
•
P
R
r
P
R
r
§
§
1
2
Follow Steps 1 to 5 of “Recording on a Tape” on
pages 6 and 7.
Recording starts.
DIRECTION MODE
SYNCHRO
PAUSE P ª/·
1
Set the source selector on the amplifier to CD
player.
Press REC MUTING R where you want to insert a
blank space.
“REC” flashes in the display and a blank is
recorded on the tape.
After 4 seconds, P lights up and the tape deck
changes to recording pause.
2
3
Insert a CD into the CD player.
Select the play mode (CONTINUE, SHUFFLE, or
PROGRAM) of the CD player.
3
Press PAUSE P to resume recording.
4
5
Insert a cassette into deck B.
Select the side(s) to be recorded on.
z If you want to insert a blank space longer than 4
seconds
To record on
Only one side
Both sides
Set DIRECTION MODE to
A
Hold down REC MUTING R as long as you want.
After 4 seconds, “REC” flashes faster.
When you release REC MUTING R, P lights up and the
tape deck changes to recording pause.
Press PAUSE P to resume recording.
a or RELAY
6
7
Select the side you want to start recording from
on deck B.
To record from
The front side
Press
·
The reverse side
ª
Press SYNCHRO.
If your CD player has the Peak Search function
The SYNCHRO button indicator lights up and the CD
player locates the highest signal level among the tracks
to be recorded as the tape deck adjusts the recording
level. When the recording level adjustment is
completed, CD Synchro-recording starts.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad va n ce d Re co rd in g Op e ra t io n s
If your CD player does not have the Peak Search
function
The CD player changes to play pause and deck B to
recording pause. Press PAUSE P on deck B to start
Synchro-Recording.
Synchro-recording With a CD
Player Using a Remote Z
By pressing the START button on the optional remote
RM-J910 (supplied for TC-WE835S U.S.A. model only),
you can perform Synchro-recording on your tape deck
with a Sony CD player. This function is possible only
with Sony CD players with remote control capability.
To stop CD Synchro-recording
Press p on deck B or the CD player.
z You can use an optional remote (supplied for TC-
WE835S U.S.A. model only) to operate the CD player
To start CD play, press P twice; to pause CD play, press
P once; to locate a CD track, press = or +.
z If the SYNCHRO button indicator goes off after
flashing rapidly
PRESET
STOP
START
STANDBY
The tape cannot be recorded on because the record-
=
+
P
protect tab(s) on the cassette has (have) been removed.
1
2
Set the source selector on the amplifier to CD
player.
z Length of tape used for recording
Tracks on a CD differ in length. Classical music CDs
and others often have tracks that exceed the recording
time of a single cassette side. In this case, record the
tape manually.
Insert a CD into the CD player and select the play
mode (CONTINUE, SHUFFLE, or PROGRAM) of
the CD player.
z When recording from the middle of the tape
A tape that is inserted and has not been played or
recorded on is assumed by the deck to be a new tape,
even if the present location is in the middle of the tape.
The deck will transport the tape for 10 seconds before
starting CD Synchro-recording to bypass the portion
corresponding with the leader. To begin CD Synchro-
recording without the ten-seconds delay, play or record
on the tape for about 10 seconds before starting the CD
Synchro-recording procedure.
3
Insert a cassette into deck B and select the side(s)
to be recorded.
To record on
Only one side
Both sides
Set DIRECTION MODE to
A
a or RELAY
4
Press STANDBY.
· lights up and the CD player changes to play
pause and deck B to recording pause. If ·
doesn’t light up, press · once.
z If the tape ends during CD Synchro-recording on the
front side of the tape (· lights up) and the
DIRECTION MODE selector is set to a or RELAY
Recording of the track ends immediately, the tape
direction is reversed, and recording starts again from
the beginning of the track. If the tape ends on the
reverse side of the tape (ª lights up), CD Synchro-
recording stops and the CD player stops playing.
To record on the reverse side
Press ª once.
5
Press START.
To stop Synchro-recording
Press STOP.
Notes
•
To prevent interruption of the recording process, do not
press any operation buttons on the CD player during CD
Synchro-recording.
z If your CD player has the Peak Search function
After performing Steps 1 to 3 above, press PRESET to
turn on the Auto Rec Level function (see page 12). Then
continue from Step 4.
•
Certain operation buttons on the tape deck are disabled
during CD Synchro-recording.
z You can use the remote to operate the CD player
To start CD play, press P twice; to pause CD play, press
P once; to locate a CD track, press = or +.
Note
Some CD player might not start playback when you press
START. In this case, press P on the CD player to start
playback.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Precautions
Notes on Cassette Tapes
To protect a recording on side A or B
Break out the respective tab.
On safety
•
Do not disassemble the cabinet — this may result in an
electrical shock. Refer servicing to qualified personnel
only.
Side A
•
Should any solid object or liquid fall into the cabinet,
unplug the tape deck and have it checked by qualified
personnel before operating it any further.
On power sources
Tab for side A
Tab for side B
•
•
•
•
Before operating the tape deck, check that the operating
voltage of the tape deck is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the tape deck.
To record on a tape with a missing record-protect
tab
Cover the respective tab hole with adhesive tape.
The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off (TC-WE835S U.S.A. and
Canadian models only).
If you are not going to use the tape deck for a long time,
be sure to disconnect the tape deck from the wall outlet.
To disconnect the AC power cord, grasp the plug itself;
never pull the cord.
AC power cord must be changed only at the qualified
service shop.
When you are using a type II or type IV tape, be careful
not to cover the detector slots that the deck uses to
determine the tape type.
On operation
•
Because of a safety mechanism, the function buttons will
not operate if the cassette holder is not completely closed,
if there is no cassette in the cassette holder, or if a cassette
has been incorrectly inserted into the cassette holder.
Be sure to stop the tape before turning off the tape deck.
Otherwise, the tape may be damaged.
Type II
Type IV
•
Detector slots
Detector slots
On placement
•
Place the tape deck in a location with adequate ventilation
to prevent heat build-up in the tape deck.
Do not place the tape deck:
On tapes longer than 90 minutes
We do not recommend the use of tapes longer than 90
minutes except for a long continuous recording or
playback. They are very thin and tend to stretch easily.
•
— on a soft surface such as a rug that might block the
ventilation holes on the bottom.
— in a location near heat sources.
— in a place subject to direct sunlight.
— in an inclined position.
On handling cassettes
• To prevent the heads and tape path from getting
dirty, avoid touching the tape surface of a cassette.
• Place cassettes away from equipment with magnets,
such as speakers and amplifiers, which may cause
tape distortion or erase the recordings.
— in a place subject to excessive dust or mechanical shock.
On cleaning the tape deck
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
• Do not expose cassettes to direct sunlight, extremely
cold temperature, or moisture.
If you have any questions or problems concerning your
tape deck, please consult your nearest Sony dealer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Demagnetizing the heads
Cleaning
After 20 to 30 hours of use, or when you notice a
hissing sound or loss of high frequencies, demagnetize
the heads with a commercially available demagnetizer
for tape decks. Please refer to the instructions of the
demagnetizer.
Head assembly
Pinch rollers
Capstans
Erasing head
Recording/playback head
U
0
p
)
0
p
)
ª
·
ª
·
•
P
R
r
P
R
r
§
§
§
Cleaning the heads and tape path
Clean the heads and tape path of the tape deck after
every 10 hours of operation to guard against:
• low-quality sound
• a decrease in sound level
• excessive wow or flutter
• sound dropout
• incomplete erasure
• impairment of recording function
To ensure better recording, we recommend that you
clean the heads and tape path before every recording.
1
Press § to open the cassette holder. Grasp the
front cover on both sides and gently lift to remove
it.
2
With the tape deck turned off, wipe the heads, the
pinch rollers and the capstans with a cotton swab
slightly moistened with alcohol or a commercially
available cleaning fluid for tape decks.
3
Replace the front cover.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
The tape stops before the tape has been fully rewound.
/The tape is slack. Take up the tape slack.
/If “M” is shown in the display, press MEMORY
repeatedly until “M” disappears.
Troubleshooting
If you’ve experienced any of the following difficulties
while using the tape deck, use this troubleshooting
guide to help you remedy the problem. Should the
problem persist, consult your nearest Sony dealer.
/The cassette shell is bent. Use another cassette.
The Multi-AMS function does not work properly.
/One of the tracks contains a long pause, a passage of
low frequencies or very low volume, or a gradual
increase or decreace in volume.
The function buttons do not work.
/The tape deck has been just turned on and does not
operate for about 3 seconds. Wait until P stops
flashing.
/The space before a track is less than 4 seconds long.
Insert a blank space of 4 seconds using the REC
MUTING R button.
/Check that the cassette is inserted correctly and the
cassette holder is closed completely.
/The signal strength of the left and right channels are
very different.
/There is noise in the space before a track.
/You pressed the ) (or 0) button immediately
before the beginning of the next track or immediately
after the beginning of the current track.
The tape deck does not play or record.
/There is no cassette in the cassette holder.
/The tape has come to the end.
/The tape is slack. Take up the tape slack.
/The record-protect tab has been removed from the
cassette (see page 18).
The Dolby NR function does not work properly during
playback.
/The Pitch Control function is on and the frequency
characteristics of the sound is altered. Push the PITCH
CONTROL button again to turn off the function.
/Make sure the amplifier setting is correct.
/Check that the tape deck connections are secure.
/The heads and tape path are dirty. Clean them (see
page 19).
/The recording/ playback head is magnetized.
Demagnetize it (see page 19).
The High-Speed Fast-Forwarding and Rewinding
functions do not work (TC-WE835S only).
/You pressed the ) (or 0) button when there is little
tape remaining in that direction. This is to protect the
tape.
There is excessive wow, flutter or sound drop-out.
/The capstans and pinch rollers are dirty. Clean them
(see page 19).
/To protect the tape, the high-speed fast-forwarding or
rewinding function may operate for only a short time
or not at all when activated in the middle of the tape.
There is a decrease in sound level, sound drop-out, or
poor reproduction of high frequencies./The tape does not
erase completely./Noise increases.
There is excessively loud tape transport noise during
fast-forwarding or rewinding.
/This noise is caused by the cassette and is not a
/The recording/ playback or erasing head and tape path
are dirty. Clean them (see page 19).
/The recording/ playback or erasing head is magnetized.
Demagnetize it (see page 19).
mechanical problem.
§ does not work.
There is hum or noise.
/The tape deck is playing back or recording. Press the
p or PAUSE P button to stop playback or recording
before pressing the § button.
/The tape deck is placed near a TV or VCR. Move the
tape deck away from the TV or VCR.
/The tape deck is placed on or under the amplifier.
Move the tape deck away from the amplifier.
/A power failure has occurred, the tape deck has been
turned off or the power cord has been disconnected
during tape operation. Reconnect the power or turn off
the tape deck, then on again.
There is an unbalanced tone.
/Check that DOLBY NR position is the same as when
the tape was recorded. An unbalanced tone may result
when a tape recorded in the S Dolby NR is played back
in B or C, or when a tape recorded in the B or C Dolby
NR is played back in the S (TC-WE835S only).
/The tape deck is placed near a TV or VCR. Move the
tape deck away from the TV or VCR.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Inputs
Specifications
Line inputs (phono jacks)
Sensitivity: 0.16 V
Input impedance: 47 kilohms
System
Recording system
Outputs
4-track 2-channel stereo
Line outputs (phono jacks)
Fast-winding time (approx.)
Rated output level: 0.5 V at a load impedance of
TC-WE835S: 90 sec. (with Sony C-60 cassette)
47 kilohms
TC-WE635: 100 sec. (with Sony C-60 cassette)
Load impedance: Over 10 kilohms
High-speed fast-winding time (approx.) (TC-WE835S only)
Headphones (stereo phone jack)
45 sec. (with Sony C-60 cassette)
Output level: 0.25 mW at a load impedance of
32 ohms
Bias
AC bias
Signal-to-noise ratio (at peak level and weighted with Dolby NR off)
Type I tape, Sony Type I (NORMAL): 55 dB
General
Power requirements
Where purchased
Type II tape, Sony Type II (HIGH): 57 dB
Type IV tape, Sony Type IV (METAL): 58 dB
Power requirements
120 V AC, 60 Hz
S/N ratio improvement (approximate values)
U.S.A. and Canada
With Dolby B NR on: 5 dB at 1 kHz, 10 dB at 5 kHz
With Dolby C NR on: 15 dB at 500 Hz, 20 dB at 1 kHz
U.K., Continental Europe, China
and certain countries in Asia
220 – 230 V AC, 50/ 60 Hz
With Dolby S NR on (TC-WE835S only): 10 dB at 100 Hz,
24 dB at 1 kHz
Australia
240 V AC, 50/ 60 Hz
Other countries
120/ 220/ 230 – 240 V AC,
50/ 60 Hz
Harmonic distortion
0.4% (with Type I tape, Sony Type I (NORMAL):
160 nWb/ m 315 Hz, 3rd H.D.)
1.8% (with Type IV tape, Sony Type IV (METAL):
250 nWb/ m 315 Hz, 3rd H.D.)
Power consumption
TC-WE835S: 30 W
TC-WE635: 22 W
Frequency response (Dolby NR off)
Tape type
Dimensions (approx.) (w/h/d)
Model for U.K. and Australia:
430 × 120 × 310 mm
Type I tape, Sony Type I
(NORMAL)
30 – 16,000 Hz (±3 dB, IEC),
20 – 17,000 Hz (±6 dB)
Model for other countries:
Type II tape, Sony Type II
(HIGH)
30 – 17,000 Hz (±3 dB, IEC),
20 – 18,000 Hz (±6 dB)
430 × 120 × 290 mm
(17 × 4 3/ 4 × 11 1/ 2 in.)
Type IV tape, Sony Type IV
(METAL)
30 – 19,000 Hz (±3 dB, IEC),
20 – 20,000 Hz (±6 dB),
30 – 13,000 Hz (±3 dB, –4 dB
recording)
including projecting parts and controls
Mass (approx.)
4.3 kg (9 lbs 8 oz)
Wow and flutter
Supplied accessories
TC-WE835S:
See page 4.
±0.13% W. Peak (IEC)
0.07% W. RMS (NAB)
±0.18% W. Peak (DIN)
TC-WE635:
Optional accessory
Remote commander RM-J910 (except TC-WE835S U.S.A.
model)
±0.13% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)
For more information on the availability of the remote
commander, contact your nearest Sony dealer.
Variable pitch range (approx.)
Design and specifications are subject to change without notice.
–30 to +30%
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
Ad d it io n a l In fo rm a t io n
Glossary
Index
ATS
A, B
Automatic Tape Selection. The tape deck automatically sets
the appropriate equalization characteristics and bias current
according to the type of tape inserted in the deck.
Accessories
optional 21
supplied 4
Adjusting
recording level automatically. See Auto rec
Automatic calibration
The automatic adjustment of the bias current and recording
level for the inserted tape.
level
recording level manually 7
volume 5
ATS 11, 22
Audio connecting cord 4
Auto play 8
This adjustment works together with the deck’s ATS
(Automatic Tape Selection, see above) to get the best
possible recording results on any tape.
Automatic Music Sensor. See Multi-AMS
Automatic calibration 11, 22
Automatic Tape Selection. See ATS
Auto rec level 12, 22
Auto Rec Level function
A function that automatically sets the recording level
according to the peak signal level of the program source
prior to recording.
C
When active, this function gradually decreases the recording
level when the signal level rises excessively during
recording.
Cassette. See Tape
CD synchro-recording
through a control A1 cord 16
using a remote 17
Cleaning
Dolby HX Pro
cabinet 18
A system that reduces distortion, and increases high-
frequency headroom during recording. A tape recorded
with this system produces the same high-quality sound even
when played on other tape decks.
heads and tape path 19
Connecting. See Hooking up
Control A1 cord 4, 16
D, E, F, G
Difference between the models 2
Dolby NR (noise reduction)
Dolby HX Pro 7, 22
Dolby NR 5, 7, 22
Dubbing
A system that eliminates tape hiss noise by boosting low-
level signals in the high-frequency range during recording,
then lowering them during playback.
high-speed dubbing 13
normal-speed dubbing 13
only specific portions 14
RMS dubbing 15
Fader 13
There are four types: A, B, C and S (TC-WE835S only). Type
A is for professional use (and is not available on your tape
deck), and types B, C and S are for consumer use. Type S
has the maximum noise reduction capability, followed by
types C and B.
Fading
in. See Fader
out. See Fader
FILTER. See Multiplex filter
Multi-AMS
Multi-Automatic Music Sensor is a function that locates the
beginning of up to 30 tracks before or after the current track
by detecting the blank space (of over 4 seconds) between
tracks.
H, I, J, K
Heads
cleaning 19
demagnetizing 19
High-speed
Multiplex filter
fast-forwarding function 5
rewinding function 5
Hooking up
hookups 4
overview 4
Insert
A filter for eliminating the 19-kHz stereo carrier and the
38-kHz sub-carrier signals that may impair the Dolby NR
system. Though tuners are usually equipped with this filter,
if you got poor results when recording FM broadcasts with
the Dolby NR, your tuner may not have a filter or the filter
may not be working. In this case, set the DOLBY NR selector
on the tape deck to ON FILTER.
blank space 16
cassette 5, 6
L
Test tones
Locating
Signals (10-kHz and 400-Hz) generated by the tape deck for
beginning of the tape 8
particular point 8
tracks 8
bias current and recording level calibration.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
M, N, O
Na m e s o f Co n t ro ls
Memory play 8
Multi-AMS 8, 22
Multiplex filter 7, 22
Bu t t o n s
A+B REC (simultaneous recording) 15
ARL (automatic recording level adjustment) 12
CHECK 9
DECK A/ DECK B 11
DISPLAY 9
P, Q
Pitch control function 5
Playing
auto play 8
basic play 5
memory play 8
FADER 13
HIGH/ NORMAL 13, 15
MEMORY 8
RMS play 9
PAUSE P 6, 11 – 13, 15, 16
PITCH CONTROL 5
REC (recording) r 6, 12, 14
REC MUTING (record muting) R 16
RESET 8
RMS/ START 9, 15
SET 9
R
Random Music Sensor. See RMS play or dubbing
Recording
basic recording 6
CD synchro-recording 16
FM broadcasts 7
on both decks in succession. See Relay
recording
SYNCHRO 16
§ (eject) 5, 6, 19
p (stop/ RMS CLEAR) 9, 12, 13
· (forward play/ RMS FRONT) 5, 6, 8, 9, 11 – 16
ª (reverse play/ RMS BACK) 8, 9, 11, 13 – 16
), 0 (fast-forwarding and rewinding/ AMS/
RMS +/ –) 8, 9
the same source on both decks. See
Simultaneous recording
Record muting 16
Relay recording 14
Remote commander 4, 17, 21
RMS dubbing 15
Se le ct o rs
RMS play
DIRECTION MODE 5, 6, 13 – 16
DOLBY NR 7
adding tracks 10
checking the order of tracks 9
Sw it ch e s
S
T
U (or 1/u) (power) 5, 6
Searching. See Locating
Simultaneous recording 15
Specifications 21
Co n t ro ls
PITCH CONTROL 5
REC (recording) LEVEL 7, 12
Tape
Ja cks
ejecting 5, 7
notes 18
path cleaning 19
protect the recording 18
type 18
CONTROL A1 4
LINE IN 4
LINE OUT 4
PHONES 5
Test tones 11, 22
Troubleshooting 20
Ot h e rs
AUTO indicator 6, 12, 13
Cassette holder 5, 6, 19
Peak level meters 7
U, V, W, X, Y, Z
Unpacking 4
SYNCHRO button indicator 17
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|