4-205-753-41(02)
R
420575341
Trinitron Colour
Television
GB
Operating Instructions
KV-32FX65 B
© 2000 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
For your safety
All TVs operate on extremely high voltages. To prevent fire or electric shock, please follow the safety procedures indicated
below.
For General Safety
•
•
•
Do not expose the TV set to rain or moisture.
Do not remove the rear cover.
For your protection, refer all servicing to qualified personnel only.
For Safe Installation
•
•
Do not install the TV in hot, humid or excessively dusty places.
Do not block or cover the ventilation openings. For ventilation, leave a space of at least 10
cm all around the set.
•
•
Do not install the TV where it may be exposed to mechanical vibrations.
Place the TV set only on a stable stand designed for the weight and dimensions of the TV.
For Safe Operation
•
•
Do not operate the TV set on anything other than a 220-240V AC, 50Hz supply.
Do not operate the TV if any liquid or solid objects fall in through the ventilation slots.
Have it checked immediately.
•
•
•
For environmental and safety reasons, it is recommended that the TV set is not left in
standby mode when not in use. Switch off at the mains.
Do not disconnect the TV by pulling on the power cable. Disconnect by removing the
mains plug.
In case of a thunderstorm, disconnect the TV set from the main supply and the aerial.
Otherwise the set may be damaged by a stroke of lightning.
For Maintenance
•
•
Clean the TV screen with a soft dampened cloth. Do not use any abrasive cleaners.
Dust and nicotine deposits may cause heat accumulation inside the TV set. In the long term
this could be a safety risk and may shorten the lifetime of your TV set. Therefore have your
set serviced about every five years.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
.
Table of Contents
Installation
1. Checking the accessories supplied
2. Inserting batteries into the remote control
3. Connecting the TV
4
4
5
6
7
7
4. Switching on the TV
5. Tuning your TV
6. Finding your video channel
Operation
Overview of the TV set buttons
Overview of the remote control buttons
NexTView
8
9
10
12
14
14
16
17
17
18
18
19
20
20
21
21
Teletext
Using the TV menu system
Adjusting the picture and sound
Using the Features menu
Re-arranging the TV channels
Manually tuning the TV
Naming a channel
Skipping programme positions
Using the ‘Further Programme Preset’ feature
Adjusting the picture rotation
Adjusting the picture geometry for an RGB source
Inputting your personal ID
Presetting and naming input signals
Additional Equipment
Connecting additional equipment to the TV
Additional information when connecting equipment
Smartlink
22
23
23
Additional Information
Specifications
24
24
25
Channel Display Table
Troubleshooting
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Follow steps 1-6 to install the TV and
view TV programmes.
1. Checking the accessories supplied
-
+
+
-
Batteries
Remote control
2. Inserting batteries into the remote control
Always observe the correct polarity when inserting batteries.
Always remember to dispose of used batteries in an environmentally friendly way.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Connecting the TV
Connecting an aerial to your TV
If you are not connecting
your TV to a VCR,
please connect the aerial
lead (as shown left) and
proceed to section
‘4.Switching on the TV’.
If you are connecting
your TV to a VCR please
refer to the section
below.
1. Connect your existing aerial lead to the socket marked
on the rear of the TV set.
Connecting an aerial and VCR to your TV
The scart lead is
optional. If it can be
used however, this
additional
connection can
improve picture and
sound quality when
in play mode.
scart lead
(not supplied)
existing aerial lead
OUT
IN
AERIAL
ANTENNA
AC IN
1. Connect your existing aerial lead to your VCR as shown.
2. Connect the VCR aerial lead from the RF OUT socket on the back of the VCR to the aerial
socket on the back of the TV as shown.
3. Connect the scart lead (if used) to the AV2 socket on the rear of the TV set.
4. Connect the VCR set to the mains and switch on.
5. Insert a pre-recorded tape into the VCR and press the ‘PLAY’ button. This enables the TV
set to locate and store the video channel during the ‘Tuning your TV’ procedure on page 7.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4. Switching on the TV
I
I/O
1. Connect the TV plug to the mains socket (220-240V AC, 50Hz).
2. Push in the on/off button
on the front of the TV.
If the standby mode indicator on the front of the TV is lit, press the TV
button on the remote control to switch on the TV set. Please be patient as
the picture may take a few moments to appear on the TV screen.
/
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
5. Tuning your TV
Before you tune your TV, you will be asked to set your language and country.
1. The Language/Country menu appears on the TV screen with the
Language country
word ‘English’ highlighted.
Čeština
Dansk
Language
Country
Deutsch
English
Español
Français
Italiano
2. Press the v or V buttons on the remote control to select your
chosen language then press the OK button to confirm.
Select Language:
Language country
Confirm:
2
5
8
0
3
6
9
1
4
7
3. Press v or V to select the country in which you wish to operate
the TV then press the OK button to confirm your choice. Select
‘OFF’ if you do not want your channels stored in a given channel
sequence starting from programme position 1.
Language
Country
English
France
Germany
Great Britain
Greece
Hungary
Ireland
Italy
Select Country:
Confirm:
4. The ‘autotune’ menu appears on the TV screen in your selected
language. Press the OK button to confirm.
OK
5. Ensure the aerial is connected as instructed, then press the OK
button to confirm. The TV starts to automatically search and store
all available channels for you. This may take a few minutes -
please be patient and do not press any buttons.
:
:
6. Once the TV has tuned all available channels the ‘Programme
Sorting’ menu appears on the TV screen enabling you to change
the order of the channels on your TV. If you wish to change the
channel order, press the v or V buttons to select the channel you
want to move, then press B. Press the v or V buttons to select the
new programme number position for your selected channel then
press the OK button to confirm. The selected channel now moves
to its new programme position and the other channels move
accordingly. Repeat this procedure if you wish to sort the order of
other channels on your TV.
:
:
Programme Sorting
PROG CH
LABEL
1
2
3
4
5
6
7
8
9
C03 TV 5
C05 PRO 7
C07 EU-SP
C08 SWF
C09 RTL
C11 SAT
C12 MDR
C13 DDI
C14 DSF
10 C15 RTL 2
11 C16 KAB 1
Select Prog:
Confirm:
7. Press the MENU button to remove the menu from the TV screen.
Programme Sorting
PROG CH
LABEL
1
2
3
4
5
6
7
8
9
C03 TV 5
C03 TV 5
8. Press the PROGR+/- or the numbered buttons to view the TV
channels.
C05 PRO 7
C07 EU-SP
C08 SWF
C09 RTL
C11 SAT
C12 MDR
C13 DDI
C14 DSF
10 C15 RTL 2
11 C16 KAB 1
Note: If you would like to stop the autotune process at any stage,
press the OK button.
Select Position:
Move: OK
6. Finding your video channel
If you have connected a VCR to your TV, you now need to find your video channel. Please refer to the ‘Connecting the TV’
section of this manual on page 3.
1. Press the PROGR+/- buttons on the TV remote control until your video picture appears on the TV screen.
Note: If you wish to move your video channel to a different programme position, refer to the ‘Re-arranging the TV channels’
section of this instruction manual.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Overview of the TV set buttons
p
-
+
s
4
4
MONO
L/G/S/I
4
R/D/D/D
Press the door flap as shown.
The control panel appears.
Programme Up (+) or Down (-) buttons.
Press to select TV channels.
Video input button.
Press to select the input
signals from VCR etc.
p
-
+
Volume control buttons.
Press to increase (+) /decrease (-) volume.
s
4
4
MONO
L/G/S/I
Master Reset button.
Press to return the picture and sound
levels to factory settings. The Sony logo
will appear on the screen followed by the
‘Autotune’ screen. If you do not wish to
retune your TV, press the b button on
your remote control.
4
R/D/D/D
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Overview of the remote control buttons
To temporarily switch off TV
Press to temporarily switch off TV. Press again to switch on
from standby mode. To save energy, we recommend
switching off completely when TV is not in use.
NOTE: After 15-30 minutes without a TV signal and
without any button being pressed, the TV switches
automatically into standby mode.
To mute sound
Press to mute TV sound. Press again to restore the
sound.
To reveal on screen information
Press to reveal all on-screen indications. Press
again to cancel. In teletext mode, press to reveal
concealed information (eg answers to a quiz) then
press to cancel.
To select input signal or freeze teletext
Press to select inputs from the TV sockets (see Using
Optional Equipment section). In Teletext mode, press to
freeze the displayed page. Press once again to cancel.
To select channels
Press the numbered buttons to select channels.
To return to previous channel
Press to return to the previous channel you were watching.
Note: This can be done only after watching the present
channel for 5 seconds.
For double digit programme numbers, e.g.23, press
-/-- first, then the buttons 2 and 3.
To display the menu
Press if you wish to use the TV menu system. Press again to
remove the menu from the TV screen.
To return to TV mode
Press to return to the normal operation from teletext
mode or standby mode.
To select menu items
Use the OK button and arrow keys to select the options
available in the menu system of this TV.
To select Teletext
Press to switch Teletext on and off.
To display picture menu
Press to change the picture settings. Press the OK
button to remove the display.
To select Electronic Programme Guide (EPG)
Press to switch EPG on and off.
To change screen format
Press to change the format of the screen. See ‘Changing the
screen size’ section of this manual for details.
To display sound menu
Press to change the sound settings. Press the OK
button to remove the display.
Fastext keys
See Teletext section of manual for details.
To adjust TV volume
Press to adjust the volume of the TV.
To select channels
Press to select channels.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
NexTView*
* depending on availability of service
NexTView is an electronic programme guide with up to 1 week* of programme information on those channels included
in the selected provider.
*If the data exceeds the memory of NexTView, you will get information on less than 7 days.
When looking for information you can search by theme (sports, art etc.), date or time (e.g. broadcasts between 8 p.m. and 9 p.m.).
When you’ve found a programme you can go directly to this programme, use the timer to remind you of it or preset your VCR
with Smartlink.
The NexTView provider is responsible for the contents of the guide. The TV set is responsible for the presentation, that
is the menu structure and the navigation, if there is none from the provider. If there is a navigation from the provider the
basic operation with the remote control is the same as described in the Sony navigation.
At first you need to select a channel providing a NexTView service. In this case the indication “NexTView” is displayed as soon
as all data is available. When you later change the channel you can still select this NexTView service.
Operation using the Sony navigation
1. Press
to switch NexTView on and off.
2. Use the remote control buttons as follows
•
•
moving up or downwards within a column: Use v or V.
going to the left columns time and date: Use b.
•
going to the right column icons: Use B.
•
(a)
(b)
Confirming a selection: Press OK.
while in the columns date, time or icon (themes), the programme list changes according to the selection.
while in the programme list, confirming a running broadcast brings you directly to the TV programme or confirming
a future programme brings you to the long info menu.
07 Tue
12:38
SWISS
TXT
TPS / RINGIER
Tue 07. 04 .98
Index
7
Tue
Star Wars
Super RTL
10:35 - 12:45
10:20 - 12:00
full list of selection
personal selection
news broadcasts
movies
sports
entertainment
children
8
Wed
Werner - Beinhart
Pro 7
9
Thu
Flui grüsst den Rest der Welt
Kabel 1
10:45 - 10:50
12
10
Fri
Once upon a time in the West
Euronews
11:00 - 11:20
11
Sat
International News
RTL Plus
11:45 - 12:50
return to last menu
12
Sun
Fantasy film, USA, 1996
13
Mon
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
NexTView*
Individual Setting
When you select
there will be no personal pre-selection.
lets you make your own individual selection of themes,
limiting the search to the marked ones.
1. Select
using v or V. Push B to enter.
The menu Individual Settings is displayed.
2. Select the item you wish to mark using v or V. Confirm by pressing OK.
Repeat step 2 for all the items you wish to have in your list.
3. When finished with the list, select
using B and press OK.
Using the ‘Long Info’ menu
1. Select a future programme in the column programme list using v or V. Press OK.
The long info menu is displayed.
First nextTView/EPG-Providers in Europe
07 Tue
SWISS
TXT
TPS / RINGIER
Tue 07. 04 .98
nexTView
12:38
Address Mapping
The position of the addresses in the
OSDA is shown in the following diagram.
The position values of the DPW are set
to '0'.
If other values are set, the complete
combination will be scrolled.
Example:
if the DPWC is set to '63', the char-
This channel has been set for a timer
VPS/PDC
On
Speed
Timer Prog
SP
VCR1
You may wish to record the selected programme with your VCR.
(only with Smartlink VCRs)
2. Select
using b and press OK.
This information is transferred to the VCR connected to your set.
Setting up ypur VCR
3. Select VPS/PDC by pushing b repeatedly.
With this setting on, you have the guaranteed recording of the whole broadcast
should there be a change in the TV programme. This only works if the selected
channel broadcasts a VPS/PDC signal.
•
Select On or Off using OK.
4. Select Speed using V.
Select between standardplay (SP) or longplay (LP) mode.With longplay you can
record twice as much on a videotape. The picture quality, however, may suffer.
•
Select SP or LP using OK.
5. Select VCR Setup using V.
Select with which of the connected Smartlink VCRs you wish programme.
•
Select VCR 1 or 2 using OK.
6. Select
using B. Press OK.
You are back in the last menu.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Teletext
Most TV channels broadcast information via Teletext. The index page of the teletext service (usually page 100) gives
you information on how to use the service. Please use a TV channel with a strong signal, otherwise there may be Teletext
errors.
Switching Teletext on and off
1. Select the TV channel which carries the teletext service you want to view.
2. Press the
3. Press
4. Press
button once to get Teletext only.
twice for Mix mode.
a third time to switch off Teletext.
m
TELETEXT
Index
Programme
News
25
153
101
98
Selecting a Teletext page
Sport
Weather
Input three digits for the page number using the numbered buttons on the remote control. If
you make a mistake, type in any three digits then re-enter the correct page number.
m
TELETEXT
Index
Using Other Teletext Functions
Programme
News
25
153
101
98
Sport
Weather
Selecting the next or preceding page
Press the
or
buttons on the remote control to select the previous or next page.
m
Selecting a sub page
A teletext page may consist of several sub pages. In this case an information line is displayed,
showing the number of subpages. Select the sub page by pressing v or V.
To freeze a Teletext page
Press the
button to freeze the page. Press again to cancel the freeze.
Revealing concealed information
Press the
button to reveal information. Press again to conceal the information.
216-02
Using colour buttons to access pages (Fastext)
(only available if the TV station broadcasts Fastext signals)
When the colour coded menu appears at the bottom of a page, press a coloured button on the
remote control (green, red, yellow or blue) to access the corresponding page.
01 02 03 04 05 06 07 08
Using the feature ‘Page Catching’
1. Press the numbered buttons on the remote control to select a teletext page which has
several page numbers on it (eg the index page).
2. Press the OK button.
3. Press v or V to select the desired page number then press the OK button. The requested
page is displayed after some seconds.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Teletext
Using the Teletext menu
1. With Teletext switched on, press the MENU button on the remote control to display the
menu on the TV screen.
Teletext
2. Press v or V to select your chosen item on the screen then press B to display the relevant
sub menu.
3. To remove the Teletext menu from the screen, press the MENU button.
Top / Bottom / Full
Text Clear
Reveal
Time Page
Page Overview
Top/Bottom/Full
Select:
Enter Menu:
The Top/Bottom/Full sub menu allows you to enlarge different sections of the Teletext page.
Press v to enlarge the upper half of the screen, Press V to enlarge the lower half. Press the OK
button to restore the page to normal size. Press b to return to the Teletext menu screen.
Top:
Bottom:
Full: OK
Text Clear
Text Clear is a function that displays a TV channel while a Teletext page is being searched for.
1. Press the
button on the remote control to select full screen text.
2. Press the MENU button to display the ‘Teletext’ menu.
3. Press v or V to highlight ‘Text Clear’ and press B to select.
4. The current TV channel is displayed. Once the text page has been found a blue
symbol will appear in the top left hand corner of the screen.
5. Press the
button on the remote control to view the page.
Reveal
Some Teletext pages contain hidden information (eg for a quiz), which can be revealed.
1. In text mode press the MENU button on the remote control to access the ‘Teletext’ menu.
2. Press v or V to highlight ‘Reveal’ and press B to select. The hidden information is
displayed on the screen.
Time Page*
*depending on availability of service.
Time Page allows a time-coded Teletext page (such as an alarm page), to be displayed at a set
time.
1. In Text mode press the MENU button on the remote control to access the ‘Teletext’ menu.
2. Press v or V to highlight ‘Time Page’ and press B to select. The ‘Time Page’ sub menu is
displayed.
3. Enter the desired page number using the numbered buttons on the remote control.
4. Enter the desired time using the remote control.
5. Press OK to confirm the settings. The TV will exit Teletext mode and the time will be
displayed in the top left hand corner of the screen. At the requested time the desired page
is displayed.
Time Page
PAGE
TIME
- - : - -
– – –
Select Page: 0-9
Next:
Page Overview*
*only available if TOP-Text is transmitted by the TV station.
In this menu the TOP-Text pages are divided into two columns, the first column showing
‘blocks’ of pages and the second showing ‘groups’ of pages.
1. Press b or B to select the first or second column.
2. Press v or V to select the relevant ‘group’ or ‘block’ of pages.
3. Press the OK button to display the chosen pages.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Using the TV menu system
The TV consists of a menu system which is based on a series of user friendly on-screen displays and menus. These displays will
help you get the most from your TV, helping you to change picture and sound settings, to alter the size of the TV picture and to
rearrange the TV channels etc.
Adjusting the picture and sound
The picture and sound are preset at the factory. You can however adjust them to suit your own taste.
1. Press the MENU button on the remote control to display the menu on the TV screen.
2. Press the v or V buttons to select for picture settings or
for sound settings then press
B to enter either the ‘Picture Adjustment’ menu or the ‘Audio Adjustment’ menu.
3. Press the v or V buttons to select the item on the screen you wish to adjust then press B to
confirm. For a description of the menu items and their effects, see the table below.
4. Press the v, V, B or b buttons to adjust your selected item.
5. As soon as you have adjusted the item, press the OK button to store the new setting.
6. Repeat steps 3-5 if you wish to adjust any of the other items.
Picture Adjustment
7. Press the MENU button to remove the menu from the TV screen.
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Personal
Picture Control
AI
On
On
Advanced
Normal
Item
Effect/Operation
Noise Reduction
Digital Mode
Colour Tone
Picture Mode
V
Live
(for live broadcasts)
Select:
Enter:
Personal (for individual settings)
Movie (for movie broadcasts)
v
Live
Personal
Movie
Contrast
Brightness*
Colour*
Hue**
Sharpness*
Less
b B More
Picture Mode
Contrast
Darker b B Brighter
Less b B More
Reddish b B Greenish
Softer b B Sharper
On
Off
*Only available if ’Personal’ is selected in ‘Picture Mode’
AI
**Only available for NTSC colour signal (eg. US video tapes)
On
Off
Reset
Resets picture to the factory preset levels
Noise Reduction
AI
V
v
V
v
V
On: Automatic optimization of contrast level
according to the TV signal.
Off: Normal.
Normal
Digital +
Advanced
(Artificial Intelligence)
Digital Mode
Colour Tone
Warm
Normal
Cool
Noise Reduction
Digital Mode
On: Reduces picture noise in case of a weak
broadcasting signal.
Off: No noise reduction.
Normal: Basic 100Hz picture quality.
Digital +: Improved picture resolution for viewing
scrolling characters.
Advanced: Optimum picture resolution creating
flicker-free pictures.
Colour Tone
V
v
Warm:
Normal: Normal.
Cool:
Gives a warm tint to the picture.
Gives a cool tint to the picture.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Sound Control
Personal
Vocal
Jazz
Item
Effect/Operation
Audio Adjustment
Rock
Equaliser Mode
Equaliser
Equaliser Mode
V
Personal
Adjustment
Vocal
Jazz
Rock
Pop
0
Balance
Loudness
Space
Auto Vol. Control
Dual Sound
Volume
Off
Off
Off
NICAM
Stereo
NICAM
Stereo
Dual Sound
v
Flat (fixed setting, cannot be adjusted)
Select Mode :
Confirm: OK
Equaliser adjustment
You can adjust the mode selected in Equaliser mode by
cutting and boosting the 5 selected frequency bands.
Press b or B to select the frequency band then V or v to
adjust the frequency. Finally, press the OK button to store
the new adjustment.
Equaliser Adjustment
(Personal)
+
0
–
If you want to store the new setting, you need to set the Equaliser mode to
‘Personal’. Personal mode permanently stores the setting, all other modes
(Vocal, Jazz, Rock, Pop) store only until the next mode change.
120
Sel:
150
1,5K 5 K
10 K
Adjust:
Confirm:OK
Balance
0
Balance
b
B
More left
More right
Off
On
Loudness
Space
Loudness
Space
V
v
Off: Normal
On: For music broadcasts
Off
On
V
v
Off: Normal
On: Special acoustic effect
Auto Vol. Control
V
v
Off: Volume level changes according to the
broadcast signal.
On: Volume level of the channels will stay the
same independent of the broadcast signal (eg
in the case of advertisements).
Off
On
Auto Vol. Control
Dual Sound
For a bilingual broadcast:
V
A for channel 1
B for channel 2
NICAM
Mono
Stereo
Dual Sound
v
For a stereo broadcast:
V
Mono
Stereo
v
When NICAM stereo is being broadcast, the indication NICAM appears briefly
on the screen.
Headphones
i Volume
Adjusts headphone volume.
Can also adjust the volume level of additional equipment
connected to the RCA sockets on the rear of the TV.
Volume
i Dual Sound
For a bilingual broadcast:
V
A for channel 1
B for channel 2
v
NICAM
B
A
Dual Sound
For a stereo broadcast:
V
Mono
Stereo
v
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Using the Features menu
1. Press the MENU button on the remote control to display the menu on the TV screen.
Features
2. Press the v or V buttons to select
for the ‘Features’ menu then press B to enter the ‘Features’
Off
On
Auto Format
Format Correction
menu.
3. Press the v or V buttons to select the desired menu item then press B to confirm. For a description
of the menu items and their effects, see the table below.
4. Press the v, V, B or b buttons to select the desired setting.
5. Press the OK button to confirm your choice of setting.
6. Repeat steps 3-5 if you wish to select any of the other items.
7. Press the MENU button to remove the menu from the TV screen.
Sleep Timer
Parental Lock
AV 2 Output
Off
Off
TV
Select:
Enter:
Item
Effect/Operation
Auto Format*
*only for aerial signal
V Off: Size of picture does not automatically adjust.
v On: The TV will automatically adjust the picture size to eliminate any
dark areas on the TV picture (as shown below):
Off
On
Auto Format
Format Correction*
V Off: 4:3/14:9 is selected.
Off
On
Format Correction
(*only if Auto Format is v On: Smart mode is selected automatically for 4:3/14:9 broadcasts.
set to ‘On’)
Sleep Timer
You can select a time after which the TV switches itself into
standby mode.
10 min
Sleep Timer
V Off
v 90 min
Parental Lock
AV2 Output
V Off: No parental lock.
v On: This feature disables the buttons on the TV when the set is in standby
mode. It is only possible to switch the set back on by pressing a
button on the remote control.
Off
On
Parental Lock
V TV audio/video signal from the aerial
AV1 audio/video signal from scart 1.
AV2 audio/video signal from scart 2.
AV3 audio/video signal from scart 3.
.
TV
AV 1
AV 2
AV 3
AV 4
AV 2 Output
v AV4 audio/video signal from connectors on front of the TV.
Changing the screen size
This feature allows you to change the size of the TV picture.
Wide
Zoom
Press the
button on the remote control repeatedly or use the v or V buttons to select one of the
following formats then press the OK button to confirm your selection:
Wide
Zoom
14:9
4:3
Smart
for 16:9 broadcasts.
widescreen format for letterbox movies.
compromise between 4:3 and 16:9 picture size.
conventional 4:3 picture size, full picture information.
imitation of wide screen effect for 4:3 broadcasts.
14:9
4:3
In Smart, Zoom and 14:9 modes parts of the top and bottom of the screen are cut off. Press v or V to adjust
the position of the image on screen (eg to read subtitles) then press the OK button to confirm.
Smart
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Re-arranging the TV channels
After tuning the TV, you can use this feature to change the order of the channels on the TV.
1. Press the MENU button on the remote control to display the menu on the TV screen.
Set Up
Auto Tuning
Programme Sorting
AV Preset
Manual Set Up
Select:
Enter:
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set Up’
Programme Sorting
menu.
PROG CH
LABEL
1
2
3
4
5
6
7
8
9
C03 TV 5
C05 PRO 7
C07 EU-SP
C08 SWF
C09 RTL
C11 SAT
C12 MDR
C13 DDI
3. Press the V button to select ‘Programme Sorting’ then press B to enter the ‘Programme Sorting’
menu.
C14 DSF
10 C15 RTL 2
11 C16 KAB 1
Select Prog:
Confirm:
4. Press the v or V buttons to select the channel you want to move then press B to confirm.
Programme Sorting
PROG CH
LABEL
5. Press the v or V buttons to select the new programme position (eg PROG 4) for your selected
channel then press the OK button to confirm. The selected channel now moves to its new
programme position and the other channels move accordingly.
1
2
3
4
5
6
7
8
9
C03 TV 5
C03 TV 5
C05 PRO 7
C07 EU-SP
C08 SWF
C09 RTL
C11 SAT
C12 MDR
C13 DDI
C14 DSF
10 C15 RTL 2
11 C16 KAB 1
6. Repeat steps 4 and 5 if you wish to sort the other channels.
Select Position:
Move: OK
7. Press the MENU button to remove the menu from the TV screen.
Manually tuning the TV
You have already tuned the TV automatically using the instructions at the start of this manual. You can however carry
out this operation manually, adding channels to the TV, one at a time.
1. Press the MENU button on the remote control to display the menu on the TV screen.
Set Up
Auto Tuning
Programme Sorting
AV Preset
Manual Set Up
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set Up’
menu.
Select:
Enter:
3. Press the V button to select ‘Manual Set Up’ on the menu screen then press B to enter the ‘Manual
Manual Set Up
Set Up’ menu.
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
4. Press the V button to select ‘Manual Programme Preset’ on the menu screen then press B to enter
Picture Rotation
O
- - - - - - -
the ‘Manual Programme Preset’ menu.
Personal ID
Select:
Enter:
5. Press the v or V buttons to select a programme number for your channel (eg PROGR 1 for BBC1)
then press B to highlight the ‘SKIP’ column.
Manual Programme Preset
PROG SKIP
SYS CH
LABEL
1
2
3
4
5
6
7
8
9
Off
Off
Off
Off
Off
Off
Off
Off
Off
B/G
B/G
B/G
B/G
B/G
B/G
B/G
B/G
B/G
B/G
B/G
C09 TV5
C10 TV
C21
C33
CXX
CXX
CXX
CXX
CXX
CXX
CXX
6. Press v to select ‘OFF’ then press B to highlight the ‘SYS’ column.
10 Off
11 Off
7. Press the v or V buttons to select the TV broadcast system or ‘EXT’ for a video input source
(AV1, AV2, ...) then press B to confirm.
Select:
Enter:
PROG
1
SKIP
Off
SYS
CH
LABEL
8. Press the v or V buttons to select ‘C’ for terrestrial channels, ‘S’ for cable channels, or ‘F’ for
B/G
D/K
IRL
direct frequency inputs then press B to confirm.
EXT
PROG
1
SKIP
Off
SYS
B/G
CH
LABEL
LABEL
9. Select the first number digit of ‘CH’ (channel) then the second number digit of ‘CH’ with the
number buttons on the remote control or Press the V button to search for the next available
channel.
C
S
F
PROG
1
SKIP
Off
SYS
B/G
CH
03
SEARCH
10. If you do not wish to store this channel on the programme number you selected, press the v or V
PROG
0
SKIP
Off
SYS
EXT
CH
LABEL
AV1
AV1
AV2
AV3
AV4
buttons to continue searching for the desired channel.
11. If this is the channel you wish to store, press the OK button.
12. Repeat steps 5-11 if you wish to store more channels then press the MENU button to remove the
menu from the TV screen.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Naming a channel
Names for channels are usually taken automatically from Teletext if available. You can however name a channel or an
input video source using up to five characters (letters or numbers).
Manual Set Up
1. Press the MENU button on the remote control to display the menu on the TV screen.
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
Picture Rotation
Personal ID
O
Up’ menu.
- - - - - - -
3. Press the V button to select ‘Manual Set Up’ then press B to enter the ‘Manual Set Up’
Select:
Enter:
menu.
4. Press the V button to select ‘Manual Programme Preset’ then press B to enter the ‘Manual
Programme Preset’ menu.
Manual Programme Preset
PROG SKIP
SYS CH
LABEL
1
2
3
4
5
6
7
8
9
Off
Off
Off
Off
Off
Off
Off
Off
Off
B/G
B/G
C09 ARD
C10 BBC
5. Press the v or V buttons to select the channel you wish to name.
6. Press the B button repeatedly until the first element of the ‘LABEL’ column is highlighted.
10 Off
11 Off
7. Press the v or V buttons to select a letter or number (select ‘-’ for a blank) then press B to
Select:
Enter:
confirm. Select the other four characters in the same way.
PROG SKIP SYS CH
Off C07
LABEL
6
I
T
E
8. After selecting all the characters, press the OK button.
9. Repeat steps 5 to 8 if you wish to label other channels.
10. Press the MENU button to remove the menu from the TV screen.
Skipping programme positions
This function enables you to skip unused programme positions when selecting them with the PROGR+/- buttons.
However, by using the number buttons you can still select the skipped programme position.
1. Press the MENU button on the remote control to display the menu on the TV screen.
Manual Set Up
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
Up’ menu.
3. Press the V button to select ‘Manual Set Up’ then press B to enter the ‘Manual Set Up’
Picture Rotation
Personal ID
O
- - - - - - -
menu.
Select:
Enter:
4. Press the V button to select ‘Manual Programme Preset’ then press B to enter the ‘Manual
Programme Preset’ menu.
5. Press the v or V buttons to select the programme position then press B to highlight the
Manual Programme Preset
‘SKIP’ column.
PROG SKIP
SYS CH
LABEL
51 Off
52 Off
53 Off
54 Off
55 Off
56 Off
57 Off
58 Off
59 Off
60 Off
61 Off
I
I
C09 BBC1
C10 BBC
6. Press the v or V buttons to select ‘Off’ or ‘On’ (if you wish to skip this programme
position) then press the OK button to store.
7. Repeat steps 5 and 6 if you wish to skip or unskip further programme positions.
8. Press the MENU button to remove the menu from the TV screen.
Select:
Enter:
PROG SKIP
SYS CH
LABEL
53
Off
On
I
F189 - - -
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Using the Further Programme Preset feature
With this feature you can a) individually adjust the volume level of each channel, b) manually fine-tune the TV to obtain
a better picture reception if the picture is distorted or c) preset the AV output for the programme positions of channels
with scrambled signals (eg from a pay TV decoder). In this way a connected VCR records the unscrambled signal.
1. Press the MENU button on the remote control to display the menu on the TV screen.
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
Manual Set Up
Up’ menu
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
Picture Rotation
Personal ID
3. Press the V button to select ‘Manual Set Up’ then press B to enter the ‘Manual Set Up’ menu.
O
- - - - - - -
4. Press the V button to select ‘Further Programme Preset’ then press B to enter the ‘Further
Select:
Enter:
Programme Preset’ menu.
Further Programme Preset
PROG
VOL
AFT DECODER
5. Press the v or V buttons to select the relevant programme number then press the B button
1
2
0
0
0
0
0
0
0
0
0
0
0
On
On
On
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
3
repeatedly to select a) VOL b) AFT or c) DECODER. The selected item changes colour.
4
5
6
7
8
9
10
11
6. a)VOL - Volume Offset
Press the v or V buttons to adjust the volume level (range -7 to +7) of the channel. Store by
pressing the OK button. Repeat steps 5 and 6a if you wish to adjust the volume level of the
other channels.
Select:
Enter:
PROG
1
VOL
0
AFT
DECODER
DECODER
DECODER
b) AFT - Automatic Fine Tuning
Press the v or V buttons to fine tune the channel frequency over a range of -15 to +15. Press
the OK button to confirm. Repeat steps 5 and 6b if you wish to fine tune other channels.
PROG
1
VOL
-5
AFT
On
PROG
1
VOL
-5
AFT
On
Off
AV1
AV2
c)DECODER
Press the v or V buttons to select AV1 or AV2 for the programme position then press the OK
button to confirm. You can now attach a decoder to the AV1 or the AV2 socket on the back of
the TV and the picture from that decoder will appear on this programme number. Repeat steps
5 and 6c to preset the AV output for other programme positions.
7. Press the MENU button to remove the menu from the TV screen.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Adjusting the picture rotation
Because of the earth’s magnetism the picture might slant. In this case you can readjust the picture.
1. Press the MENU button on the remote control to display the menu on the TV screen.
Set Up
Auto Tuning
Programme Sorting
AV Preset
Manual Set Up
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
Up’ menu.
Select:
Enter:
3. Press the V button to select ‘Manual Set Up’ then press B to enter the ‘Manual Set Up’
menu.
Manual Set Up
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
4. Press the V button to select ‘Picture Rotation’ then press B to enter the ‘Picture Rotation’
sub menu.
Picture Rotation
O
- - - - - - - - - -
Personal ID
5. Press the v or V buttons to rotate the picture over a range of -5 to +5 then press the OK
Rotate:
Confirm: OK
button to store.
6. Press the MENU button to remove the menu from the TV screen.
Adjusting the picture geometry for an RGB source
When connecting an RGB source such as a Sony Playstation you may need to readjust the geometry of the picture.
1. Press the
button on the remote control to select the connected RGB source
.
1
RGB Set Up
H Centre
2. Press the MENU button to display the menu on the TV screen.
O
3. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
O
H Size
Up’ menu.
Adjust Position:
Confirm: OK
4. Press the V button to select ‘Manual Set Up’ on the menu screen then press B to enter the
‘Manual Set Up’ menu.
5. Press the V button to select ‘RGB Set Up’ on the menu screen then press B to enter the
RGB Set Up
H Centre
‘RGB Set Up’ sub menu.
O
O
6. Press B to select H Centre then press v or V to adjust the centre of the picture over a range
H Size
of -10 to +10. Store the new range by pressing the OK button.
Adjust Size:
Confirm: OK
7. Press B to select H Size then press v or V to adjust the horizontal coordinates over a range
of -10 to +10. Store the new range by pressing the OK button.
8. Press the MENU button to remove the menu from the TV screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV menu system:
Inputting your personal ID
With this feature, you can allocate a safety code to your TV which will enable you to be traced if the TV is stolen and
recovered. The safety code however can only be entered once - please make a note of it!
1. Press the MENU button on the remote control to display the menu on the TV screen.
Manual Set Up
Language/Country
2. Press the V button to select the
symbol on the menu screen then press B to enter the
Manual Programme Preset
Further Programme Preset
RGB Set Up
‘Set Up’ menu.
Picture Rotation
Personal ID
- - - - - - -
3. Press the V button to select ‘Manual Set Up’ on the menu screen then press B to enter the
Select. A-Z, 0-9:
Store: OK
‘Manual Set Up’ menu.
4. Press the V button to select ‘Personal ID’ on the menu screen then press B to enter the
‘Personal ID’ sub menu.
5. Press the v or V buttons to select the first of a total of 11 characters (letter, number + or a
blank) then press B to go to the next character.
6. Repeat step 5 to input all the characters for the code.
7. Press the OK button to store. A status box appears on screen requesting you to re-enter
your code.
8. Press the OK button to store the code or press b to cancel.
9. Press the MENU button to remove the menu from the TV screen.
Presetting and naming input signals
Using this feature you can label input sources.
1. Press the MENU button on the remote control to display the menu on the TV screen.
AV Preset
INPUT
AUTO FORMAT LABEL
2. Press the V button to select the
symbol on the menu screen then press B to enter the ‘Set
On
On
On
On
AV 1
AV 2
AV 3
AV 4
AV 1
AV 2
AV 3
AV 4
Up’ menu.
3. Press the V button to select ‘AV Preset’ on the menu screen then press B to enter the ‘AV
Select:
Enter:
Preset’ menu.
AV Preset
4. Press the v or V buttons to select the desired AV input (AV1, 2, 3 or 4)..
INPUT
AUTO FORMAT LABEL
Off
On
On
On
AV 1
AV 2
AV 3
AV 4
AV 1
AV 2
AV 3
AV 4
5. Press the B button to select ‘AUTO FORMAT’ then press the v or V buttons to select ‘Off’
or ‘On’.
Next:
Confirm: OK
Select:
6. Press the B button to select ‘LABEL’.
AV Preset
7. Press the v or V buttons to select the first character of the name then press the B button to
INPUT
AUTO FORMAT LABEL
move to the next character.
On
On
On
On
AV 1
AV 2
AV 3
AV 4
AV 1
AV 2
AV 3
AV 4
8. Repeat step 7 to select the other 4 characters then store by pressing the OK button.
Confirm: OK
Select: A-Z, 0-9:
9. Repeat steps 4-8 for the other AV input sources then press the MENU button to remove the
menu from the TV screen.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Equipment
Connecting additional equipment to the TV
Using the illustrations below, you can connect a wide range of audio and video equipment to your TV.
p
-
+
s
4
4
MONO
L/G/S/I
4
R/D/D/D
p
ABC
8mm/Hi8
-
+
S-VHS/Hi8
camcorder
camcorder
F
s
4
4
MONO
L/G/S/I
G
H
4
D
R/D/D/D
E
VCR
Playstation
DVD
Hi-Fi
Decoder
To view the input signals of connected equipment, please follow the instructions below.
1. Using the illustrations above, connect your equipment to the appropriate TV socket.
2. Press the
button repeatedly on the remote control until the correct input symbol for your equipment appears on the TV
screen (see table below):
Symbol on
Input signals from connector
the TV screen
•
•
•
•
Audio/video input signal through scart connector Aor* RGB through scart connector A
Audio/video input signal through scart connector Bor* S-video through scart connector B
Audio/video input signal through scart connector Cor* S-video through scart connector C
1
2
3
4
S-video input signal through the 4-pin DIN connector For* video input signal through phono jack
Gand audio input signal through phono jacks H
* automatic detection of the signal according to the connected equipment
3. Switch on the connected equipment. The picture from this equipment (if any are available) will appear on the TV screen.
4. Press
to return to the normal TV screen.
Note: To avoid picture distortion, do not connect equipment to the Fand Gsockets at the same time
Connecting Headphones
Plug in your headphones to the socket Eon the front of the TV set.
Connecting Hi-fi Equipment
Plug in your external audio equipment to the output sockets Don the rear of the TV set.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Equipment
Additional information when connecting equipment
*
*
*
*
If the picture or sound is distorted, move the VCR away from the TV set.
When connecting a monaural VCR, connect only the white jack to both the TV set and the VCR.
s
2
For information on how to select the output signal of the scart 2
/
, see page 16.
2
When connecting external hi-fi equipment, you can adjust the volume level by adjusting the headphones setting in the
sound menu - please refer to the ‘Adjusting the picture and sound’ section of this manual.
Smartlink
Smartlink is a direct link between your TV and VCR.
For Smartlink you need:
*
*
A VCR which supports Smartlink, NexTView Link, Easy Link or Megalogic.
s
2
A fully-wired 21-pin scart cable to connect your VCR to scart 2
/
connector.
2
The features of Smartlink are:
*
*
*
Tuning information such as the channel overview are downloaded from the TV set to the VCR.
With NexTView you can programme your VCR easily.
Direct TV recording: while watching TV you need to press just one button on the VCR to record this programme.
For more information on Smartlink please refer to your VCR instruction manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Specifications
TV system
B/G/H, D/K, I, L
Sound output
Left/Right: 2x20W (Music Power)
2x10W (RMS)
Sub woofer: 30W (Music Power)
15W (RMS)
Colour system
PAL,
SECAM, NTSC 3.58, 4.43 (only Video In)
Power consumption
122W
Channel coverage
See the ‘Channel Display Table’ below.
Dimensions (wxhxd)
Approx. 883x567x562mm
Picture tube
FD Trinitron WIDE, Approx. 82cm (32 inches)
Weight
Approx. 64kg
Rear Terminals
/
/
/
21-pin Euro connector (CENELEC standard) including audio/
video input, RGB input, TV audio/video output.
21-pin Euro connector (CENELEC standard) including audio/
video input, S-video input, Selectable audio/video output.
21-pin Euro connector (CENELEC standard) including audio/
video input, S-video input, Monitor audio/video output.
1
2
3
1
s 2
s 3
Accessories supplied
RM-887 remote control (1)
IEC designated size AA batteries (2)
Optional accessory
L/G/S/I RCA connectors, variable output for audio signals.
R/D/D/D
TV Stand:
SU-32FX2
Other features
Flat display Trinitron tube, noise reduction, graphic equaliser,
2000 page TEXT memory, personal ID, sleep timer,
NexTView.
RF In
Front Terminals
Video input -phono jacks
Audio inputs - phono jacks
S video input - 4 pin DIN
4
4
s 4
Design and specifications are subject to change
without notice.
Headphones jack - minijack stereo
Channel Display Table
Receivable Channels
E2..12, 21..69
Channel Displays
B/G/H
C02..C12, C21..69
S01..S41
KABEL-TV (1)
KABEL-TV (2)
S1..S41
S01..S05
M1..M10
S42..S46
S01..S10
U1..U10
S11.S20
ITALIEN
D/K
A, B..H, H1, H2
R01..R12, R21..R69
S01..S05
C13, C14..C20, C11, C12
C01..C12, C21..C69
S42..S46
L
I
F2..F10, F21..F69
B21..B69
C01..C12, C21..C69
C21..C69
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
Here are some simple solutions to problems which may affect the picture and sound.
Problem
Suggested remedy
No picture (screen is dark), no sound.
•
•
•
Plug the TV in.
Press the
button on the front of the TV.
indicator is on press the button or a numbered
If the
/
button on the remote control.
Check the aerial connection.
Turn the TV off for 3 or 4 seconds and then turn it on again
•
•
using the button on the front of the TV.
Poor or no picture (screen is dark), but
good sound.
•
•
Using the MENU system, select the Picture Adjustment
display. Adjust the brightness, picture and colour balance
levels.
From the Picture Adjustment display select RESET to return
to the factory settings.
Good picture, no sound.
•
•
Press the
If is displayed on the screen, press the
remote control.
button on the remote control.
button on the
No colour on colour programmes.
•
•
Using the MENU system, select the Picture Adjustment
display and adjust the colour setting.
From the Picture Adjustment display select RESET to return
to the factory settings.
Distorted picture when changing
programmes or selecting Teletext.
•
Turn off any equipment connected to the scart connectors on
the rear of the TV.
Remote control does not function.
•
•
Replace the batteries.
Contact your nearest Sony service centre.
The standby indicator
flashes.
on the TV
Interference on picture from external
equipment.
•
Reduce sharpness level.
•
•
If you continue to have these problems, have your TV serviced by qualified personnel.
NEVER open the casing yourself.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPRESO EN ESPAÑA
Sony España, S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|