3-859-179-11 (1)
Operating Instructions
CDP-CE515
CDP-C460Z
1997 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
TABLE OF CONTENTS
Getting Started
Unpacking ............................................................................................................................. 4
Hooking Up the System ...................................................................................................... 4
Connecting Another CD Player ......................................................................................... 6
Playing a CD ............................................................................................................................. 8
Playing CDs
Using the Display .............................................................................................................. 10
Replacing Discs While Playing a Disc ............................................................................ 12
Locating a Specific Disc .................................................................................................... 12
Locating a Specific Track .................................................................................................. 13
Locating a Particular Point in a Track ............................................................................ 14
Playing Repeatedly ............................................................................................................ 14
Playing in Random Order (Shuffle Play) ....................................................................... 14
Creating Your Own Program (Program Play) ............................................................... 15
Controlling Another CD Player (Mega Control)........................................................... 18
Playing Alternately (No-Delay Play/X-Fade Play) ...................................................... 19
Recording From CDs
Recording Your Own Program ........................................................................................ 20
Recording a CD by Specifying Tape Length (Time Edit)
(CDP-CE515 only) .............................................................................................................. 20
Fading In or Out................................................................................................................. 21
Adjusting the Recording Level (Peak Search)
(CDP-CE515 only) .............................................................................................................. 22
Storing Information About CDs (Custom Files)
What You Can Do With the Custom Files .................................................................... 23
Labeling Discs (Disc Memo)............................................................................................ 23
Storing Specific Tracks (Delete Bank) ............................................................................ 25
Additional Information
Precautions ......................................................................................................................... 26
Notes on CDs ...................................................................................................................... 26
Troubleshooting ................................................................................................................. 27
Specifications ...................................................................................................................... 27
Index
Index ..................................................................................................................... Back cover
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
Unpacking
Hooking Up the System
Check that you received the following items:
• Audio connecting cord (1)
• Remote commander (remote) (1)
• Sony SUM-3 (NS) batteries (2)
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
Inserting batteries into the remote
DIGITAL OUT
(OPTICAL)
CD player
You can control the player using the supplied remote.
Insert two size AA (R6) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor g on the player.
LINE OUT
(L)
LINE OUT
(R)
To an AC outlet
Audio input
(R)
Audio input
(L)
Amplifier
When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the player,
replace all the batteries with new ones.
Notes
To an AC outlet
: Signal flow
• Do not leave the remote near an extremely hot or humid
place.
What cords will I need?
Audio cord (supplied) (1)
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
• If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
White
(L)
Red
(R)
White
(L)
Red
(R)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
If you have a Sony component with the CONTROL A1
jack
Hookups
When connecting an audio cord, be sure to match the
color-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
Connect the component via the CONTROL A1 jack. You
can simplify the operation of audio systems composed of
separate Sony components. For details, refer to the
supplementary “CONTROL-A1 Control System”
instructions.
CD player
Amplifier
INPUT
CD
When using another Sony CD player together with
this player
You can make the supplied remote effective only for this
2ND
LINE
CD
IN
OUT
player.
L
L
• When using a player equipped with the COMMAND
MODE selector:
R
R
Leave the COMMAND MODE selector of this player
to CD 1 which is set at the factory and set that of
another player to CD 2 or CD 3. Then set the CD 1/2/3
switch on the remote supplied for each player
accordingly.
• When using a player not equipped with the
COMMAND MODE selector:
The command mode of the player without the
COMMAND MODE selector is set to CD 1. Set the
COMMAND MODE selector of this player and the
CD 1/2/3 switch on the remote to CD 2 or CD 3.
You can adjust the output level to the amplifier
Press LINE OUT LEVEL +/– on the remote. You can
reduce the output level up to –20 dB.
When you reduce the output level, “
FADE
” appears in
the display.
Note
If you press the LINE OUT LEVEL +/– buttons on the
remote while recording, the recording level will change
even when it is preset on the tape deck, etc.
• If you have a digital component such as a digital
amplifier, D/A converter, DAT or MD
Connect the component via the DIGITAL OUT (OPTICAL)
connector using the optical cable (not supplied). Take off
the cap and plug in the optical cable.
Connecting the AC power cord
Connect the AC power cord to a wall outlet.
Note that you cannot use fading in or out (page 21) and
Time Fade (page 22) functions when making this
connection.
Transporting the player
Before transporting the player, follow the procedure
below to return the internal mechanisms back to their
original position.
POC-15
1
2
Remove all the discs from the disc tray.
Press § OPEN/CLOSE to close the disc tray.
“–NO DISC–” appears in the display.
Wait for 10 seconds, then press POWER to turn off
the player.
Optical cable (not supplied)
3
Digital component
CD player
DIGITAL
OUT
DIGITAL
INPUT
OPTICAL
OPTICAL
Note
When you connect via the DIGITAL OUT (OPTICAL)
connector, noise may occur when you play CD software other
than music, such as a CD-ROM.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
What cords will I need?
• Audio cord (1) (Use the cord supplied with the player to be
connected.)
Connecting Another CD Player
• CONTROL A1 cord (1) (not supplied)
If you have a Sony CD player equipped with the
CONTROL A1 jack and the command mode of that
player can be set to CD 3, you can control that player as
the second player with this unit. After connecting this
unit and an amplifier, follow the procedure below.
Be sure to turn off the power of each player before
making this connection.
1
Connect the players with an audio cord (see also
“Hookups” on page 5).
CDP-CX200, etc.
CDP-CE515/C460Z
LINE OUT
2ND
LINE
CD
IN
OUT
L
COMMAND
MODE
To LINE OUT
L
R
CDP-CE515/C460Z
R
2
Connect the players with a CONTROL A1 cord.
CDP-CX200, etc.
CDP-CE515/C460Z
To S-LINK/
CONTROL A1
S-LINK
CONTROL A1
To 2ND CD IN
CONTROL A1
To an AC outlet
CDP-CX200, etc.
To audio output
For details on this connection, refer to the
supplementary “CONTROL-A1 Control System”
instructions.
To CONTROL A1
3
Set the COMMAND MODE selector of each
player.
Set the COMMAND MODE selector of this player
to CD 1 or CD 2, and set that of the second player
to CD 3.
To an AC outlet
COMMAND
MODE
CD
To audio input
Amplifier
1
2
3
For details on how to operate the second player,
see “Controlling Another CD Player” on page 18
and “Playing Alternately” on page 19.
: Signal flow
To an AC outlet
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
4
Connect the AC power cord of both players to AC
outlets.
Notes
• Do not connect a player other than that you use as the
second player to the 2ND CD IN jacks of this player.
• When connecting a second CD player, do not connect the
DIGITAL OUT (OPTICAL) connector of this unit to the
amplifier.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sic Op e ra t io n s
Pla yin g a CD
2 5
6 4 3
CONTINUE
SHUFFLE
PROGRAM
REPEAT
DISC CHECK
OPEN/CLOSE
EX-
CHANGE
DISC
SKIP
POWER
DISC
1
DISC
2
DISC
3
DISC
4
DISC
5
AMS
(DISC)
PHONES
PUSH ENTER
TIME/
TEXT
EDIT/
PEAK
MEMO INPUT
FADER
(-AMS+
)
CHECK
CLEAR
NO DELAY
X-FADE
TIME FADE SEARCH
MEGA
Connect the
headphones.
CONTROL
• See pages 4 – 5 for the hookup
information.
Turn on the amplifier and select the CD player position so that
you can listen to the sound from this player.
1
2
Press POWER to turn on the player.
Press § OPEN/CLOSE, and place a disc on the disc tray.
3
With the label side up
Disc number
To place other discs, press DISC SKIP and place the discs in the
order you want to play.
4
5
Each time you press the button, the disc tray turns and you can
place the discs in the empty disc compartments. The player
plays the disc in front of you first.
Press CONTINUE to select ALL DISCS or 1 DISC Continuous
Play mode.
Each time you press the CONTINUE button, “ALL DISCS” or
“1 DISC” appears in the display.
When you select
The player plays
ALL DISCS
All discs in the player consecutively in the order of
disc number
1 DISC
Only the disc you’ve selected
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sic Op e ra t io n s
You can select the disc you
want to start playing first
Press one of the DISC 1 – 5
buttons.
Press ·.
6
The disc tray closes and the player plays all the tracks once
(Continuous Play). Adjust the volume on the amplifier.
You can adjust the output
level to the amplifier Z
Press LINE OUT LEVEL +/–
on the remote. You can
reduce the output level up to
–20 dB.
To stop playback
Press p.
· P p
DISC 1 – 5
DISC SKIP
When you reduce the output
FADE
level, “
” appears in the
display.
CONTINUE
SHUFFLE
PROGRAM
REPEAT
DISC CHECK
OPEN/CLOSE
EX-
CHANGE
DISC
SKIP
The headphones volume
will also change when you
adjust the output level.
POWER
DISC
1
DISC
2
DISC
3
DISC
4
DISC
5
AMS
(DISC)
PHONES
PUSH ENTER
TIME/
TEXT
EDIT/
PEAK
MEMO INPUT
FADER
(-
AMS+
)
CHECK
CLEAR
NO DELAY
X-FADE
TIME FADE SEARCH
MEGA
Note
CONTROL
If you press the LINE OUT
LEVEL +/– buttons on the
remote while recording, the
recording level will change
even when it is preset on the
tape deck, etc.
≠ AMS
§ OPEN/CLOSE
To
You need to
Pause
Press P
Resume play after pause
Go to the next track
Press P or ·
Turn ≠ AMS
Turn ≠ AMS
Press DISC SKIP
Press DISC 1 – 5
clockwise
Go back to the preceding track
Go to the next disc
counterclockwise
Select a disc directly
Stop play and remove the CD
Press § OPEN/CLOSE
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
Display information while playing a disc
Using the Display
While playing a disc, the display shows the current
disc number, track number, playing time of the track
and the music calendar.
You can check information about the disc using the
display.
Current disc number
Playing time
CDP-CE515
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
1 1 1.56CD1
Current track number
Music calendar
TIME/TEXT
The track numbers in the music calendar disappear
after they are played.
CDP-C460Z
TIME/TEXT
Checking the remaining time
Each time you press the TIME/TEXT button while
playing a disc, the display changes as shown in the
chart below.
Checking the total number and playing
time of the tracks
ALL DISCS
Playing time and
number of the
current track
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
1 1 1.56
CD1
Press TIME/TEXT before you start playing.
The display shows the current disc number, the total
number of tracks, total playing time and music
calendar.
Press TIME/TEXT.
ALL DISCS
Remaining time
on the current
track
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
1 1 -1.57
CD1
Current disc number
Total playing time
If the track number exceeds 24,
“– – – –” appears instead of the
remaining time.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
1 1O 45.28CD1
Press TIME/TEXT.
Music calendar
Total number of tracks
ALL DISCS
Remaining time
on the disc
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
1
-43.32
CD1
The information also appears when you press the
§ OPEN/CLOSE button to close the disc tray.
The tracks numbered over 20 cannot be displayed in
the music calendar.
This information is available only in
Continuous Play mode.
Press TIME/TEXT.
Notes on the disc number indications
• The red circle around a disc number indicates the disc is
ready to be played.
• When all the tracks on a disc have been played, the semi-
circle around the disc number disappears.
• When a disc compartment is recognized as empty, the semi-
circled disc number disappears.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
• While playing a disc
Checking the information of CD-TEXT discs
CD-TEXT discs have information, such as the disc titles
or artist names, memorized in a blank space on the
discs where there is no information on normal discs.
The display shows the CD-TEXT information of the
disc so that you can check the current disc title, artist
name and track title. When the player detects CD-
TEXT discs, the “CD-TEXT” indication lights up in the
display. Each time you press the TIME/TEXT button,
the display changes as shown in the charts below.
ALL DISCS
CD-TEXT
1
6
2
7
3
8
4
9
5
1
2
3
4
5
Track title
10
TRACK
HitechBlues
CD1
This information also appears when
the player locates the track.
Press TIME/TEXT.
ALL DISCS
CD-TEXT
1
6
2
7
3
8
4
9
5
1
2
3
4
5
• Before you start playing
Playing time
10
DISC
TRACK
MIN
SEC
2 1 1.56
CD1
ALL DISCS
DISC
CD-TEXT
1
6
2
7
3
8
4
9
5
Press TIME/TEXT.
1
2
3
4
5
Disc title
10
SONYHITS
CD1
ALL DISCS
CD-TEXT
Remaining time
on the current
track
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
TRACK
MIN
SEC
2 1 -1.57
CD1
Press TIME/TEXT.
ALL DISCS
CD-TEXT
1
6
2
7
3
8
4
9
5
1
2
3
4
5
Artist name
If the track number exceeds 24,
“– – – –” appears instead of the
remaining time.
10
ART.
Sony Band
CD1
Press TIME/TEXT.*
Press TIME/TEXT.
ALL DISCS
CD-TEXT
1
6
2
7
3
8
4
9
5
Remaining time
on the disc
1
2
3
4
5
* The display shows the current disc number, total number of
tracks and total playing time of the disc for a few seconds
before returning to the disc title indication.
10
DISC
TRACK
MIN
SEC
2
-58.5‚
CD1
This information is available only in
Continuous Play mode.
Press TIME/TEXT.
If each CD-TEXT information has more than 12
characters, the first 12 characters light up after all the
characters scrolled in the display.
Note
This player can only display the disc titles, track titles and
artist names from CD-TEXT discs. The other CD-TEXT
information cannot be displayed.
To play disc highlights Z
Some CD-TEXT discs have a feature to play only the
highlights of the discs.
Press HIGH-LIGHT on the remote to start playing disc
highlights in the stop mode.
“HIGH LIGHT” flashes in the display while playing disc
highlights.
If you press the HIGH-LIGHT button while selecting discs
without this feature, “NO HIGHLIGHT” appears in the
display.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
Replacing Discs While Playing
a Disc
Locating a Specific Disc
You can locate any disc before or while playing a disc.
You can open the disc tray while playing a disc so that
you can check what discs are to be played next and
replace discs without interrupting playback of the
current disc.
DISC 1 – 5
DISC CHECK*
·
DISC SKIP
EX-CHANGE
DISC SKIP
*CDP-CE515 only
DISC
1
2
3
Press EX-CHANGE.
Number
buttons
The disc tray opens and two disc compartments
appear. Even if the player is playing a disc, it
doesn’t stop playing.
ENTER
·
Replace discs in the compartments with new ones.
The player plays the disc on the left side
compartment after the current disc, and then the
one on the right side compartment.
DISC SKIP +
Press DISC SKIP.
The disc tray turns and other two disc
compartments appear.
To locate
Press
The next disc
DISC SKIP while playing a disc.
When using the remote, press
DISC SKIP +.
4
5
Replace discs in the compartments with new ones.
A specific disc directly
DISC 1 – 5.
Press EX-CHANGE.
The disc tray closes.
When using the remote, follow
the procedure below.
1 Press DISC.
2 Press the number button of
the disc.
While the disc tray is open by pressing the EX-CHANGE
button
3 Press ENTER.
• If the playback of the current disc ends, the player stops
playing. If the disc is played in 1 DISC Repeat Play mode
(see page 14), the current disc starts playing again.
• In ALL DISCS Shuffle Play mode (see page 14), tracks are
reshuffled on the current disc.
• In Program Play mode (see page 15), only the tracks on the
current disc are played.
• Do not push the disc tray to close it in Step 5, as you may
damage the player.
A disc while checking the
labels (CDP-CE515 only)
DISC CHECK while the disc
tray is open. The disc tray turns
to show you each disc label.
When the disc you want comes
in front of you, press · to
start playing.
A disc by scanning the first
track of each disc for 10
seconds (CDP-CE515 only)
DISC CHECK before you start
playing while the disc tray is
closed. When you find the disc
you want, press · to start
playing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
You can extend the playing time during scanning the
discs
Press DISC CHECK repeatedly until the playing time
you want (10, 20 or 30) appears in the display. Each time
you press the button, the playing time changes cyclically.
To locate
You need to
The next or
succeeding tracks
Turn ≠ AMS
clockwise until
you find the track. When using the
remote, press + repeatedly until you
find the track.
The current or
preceding tracks
Turn ≠ AMS
counterclockwise
Notes
until you find the track. When using
the remote, press =repeatedly until
you find the track.
• When you press the DISC CHECK button, the play mode
automatically changes to ALL DISCS Continuous Play
mode.
• When you’ve opened the disc tray by pressing the
EX-CHANGE button, you cannot use the DISC CHECK
function.
• Even if you press the DISC CHECK button while
“REPEAT” appears in the display (see page 14), the player
stops after scanning all the discs once.
A specific track
directly Z
Press the number button of the track
on the remote
A track by scanning
each track for 10
seconds Z
Press MUSIC SCAN on the remote
before you start playing. When you
find the track you want, press · to
start playing.
(Music Scan)
When you directly locate a track numbered over 10 Z
Press >10 first, then the corresponding number buttons
on the remote. To enter “0,” use button 10.
Example: To play track number 30
Locating a Specific Track
Press >10 first, then 3 and 10.
You can quickly locate any track while playing a disc
using the AMS (AMS: Automatic Music Sensor) control
or number buttons on the remote.
You can extend the playing time during Music Scan
Press MUSIC SCAN repeatedly until the playing time
you want (10, 20 or 30) appears in the display. Each time
you press the button, the playing time changes cyclically.
≠ AMS
MUSIC SCAN
Number buttons
>10
·
=/+
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
When the disc is played in
The player repeats
Locating a Particular Point in a
Track
Continuous Play
(ALL DISCS) (page 8)
All the tracks on all discs
Continuous Play
(1 DISC) (page 8)
All the tracks on the current
disc
You can also locate a specific point in a track while
playing a disc.
Shuffle Play
(ALL DISCS) (page 14)
All the tracks on all discs in
random orders
Shuffle Play
(1 DISC) (page 15)
All the tracks on the current
disc in random orders
Program Play (page 15)
The same program
To cancel Repeat Play
Press REPEAT repeatedly until “REPEAT OFF” appears in the
0/)
display.
To locate
Press
Repeating the current track
A point while
) (forward) or 0 (backward) and
monitoring the sound hold down until you find the point
You can repeat only the current track while the disc is
played in any play mode.
A point quickly by
) (forward) or 0 (backward) and
observing the display hold down until you find the point.
during pause
You will not hear the sound during the
operation.
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
Note
If “OVER” appears in the display, the disc has reached the
end while you were pressing the ) button. Press 0 or
turn ≠ AMS
counterclockwise to go back.
Playing in Random Order
(Shuffle Play)
Playing Repeatedly
You can have the player “shuffle” tracks and play in a
random order. The player shuffles all the tracks on all
discs or on the disc you’ve specified.
You can play discs/tracks repeatedly in any play
mode.
·
SHUFFLE
DISC 1 – 5
REPEAT
Shuffle Play on all discs
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the discs/tracks as follows:
You can play all tracks on all discs in a random order.
1
2
Press SHUFFLE repeatedly until “ALL DISCS”
appears in the display.
Press · to start ALL DISCS Shuffle Play.
The
indication appears while the player is
“shuffling” the tracks.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
To cancel Shuffle Play
Press CONTINUE.
Creating Your Own Program
(Program Play)
You can start Shuffle Play while playing
Press SHUFFLE, and Shuffle Play starts from the current
track.
You can arrange the order of the tracks on the discs
and create your own program. The program can
contain up to 32 “steps” — one “step” may contain a
track or a whole disc.
You can specify discs during Shuffle Play (Select
Shuffle Play)
You can specify discs during ALL DISCS Shuffle Play
mode, and the tracks on the specified discs are played in
a random order.
PROGRAM
·
≠ AMS
DISC 1 – 5
Press DISC 1 – 5 to specify the discs after Step 1.
Semi-circles appear around the specified disc numbers in
the display. To cancel the selected discs, press DISC 1 – 5
again. The semi-circles disappear.
To return to ALL DISCS Shuffle Play, press SHUFFLE
twice.
CHECK
CLEAR
Shuffle Play on one disc
PROGRAM
You can play all tracks on the specific disc in a random
order.
DISC
Number
buttons
1
2
Press SHUFFLE repeatedly until “1 DISC” appears
in the display.
ENTER
CLEAR
>10
CHECK
Press DISC 1 – 5 to start 1 DISC Shuffle Play on the
selected disc.
·
The
indication appears while the player is
=/+
“shuffling” the tracks.
Creating a program on the player
To cancel Shuffle Play
Press CONTINUE.
1
Press PROGRAM.
“PROGRAM” appears in the display.
If a program is already stored, the last step of the
program appears in the display. When you want to
erase the whole program, hold down CLEAR until
“ALL CLEAR” appears in the display (see page
17).
You can start Shuffle Play while playing
Press SHUFFLE, and Shuffle Play starts from the current
track.
2
Press DISC 1 – 5 to select the disc.
1
6
2
7
3
8
4
9
5
1
2
3
4
5
PROGRAM
DISC
A
10
TRACK
MIN
SEC
1 AL 45.28CD1
“AL” in the display stands for “all” tracks.
When you want to program the whole disc as one
step, skip Steps 3 to 4, and go to Step 5.
(Continued)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
The program remains even after the Program Play
ends
When you press the · button, you can play the same
program again.
3
Turn ≠ AMS
want appears in the display.
The track number being programmed flashes and
the total playing time including the track appears
until the track number you
in the display.
Track number
being programmed
The program remains until you erase it or turn off the
player
Total playing time
If you replace discs, the programmed disc and track
numbers remain. So, the player plays only the existing
disc and track numbers. However, the disc and track
numbers that aren’t found in the player or on the disc are
deleted from the program, and the rest of the program is
played in the programmed order.
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
TRACK
MIN
SEC
1 5 13.18CD1
4
Push ≠ AMS
to select the track.
Note
Last programmed
track
Playing order
The total playing time doesn’t appear when:
—You have programmed a track whose number exceeds 20.
—The total playing time of the program exceeds 200 minutes.
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
TRACK
STEP
1 5 3
CD1
Creating a program using the remote Z
Programmed tracks
1
Press PROGRAM.
“PROGRAM” appears in the display.
After one second
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
2
Press DISC.
TRACK
MIN
SEC
1 5 13.18CD1
2
1
2
3
4
5
PROGRAM
A
8
Total playing time
DISC-[_]
CD1
If you’ve made a mistake
Press CLEAR, then repeat Steps 3 and 4.
3
4
Press the number button of the disc.
2
1
2
3
4
5
PROGRAM
5
6
To program other discs or tracks, do the following:
A
8
DISC-[1]
CD1
Repeat Step(s)
2
To program
Other discs
Press ENTER to select the disc.
3 and 4
Other tracks on the same disc
Other tracks on other discs
1
6
2
7
3
8
4
9
5
1
2
3
4
5
PROGRAM
DISC
A
2 through 4
10
TRACK
MIN
SEC
1 AL 45.28CD1
Press · to start Program Play.
When you want to program the whole disc as one
step, skip Steps 5 to 6, and go to Step 7.
To cancel Program Play
Press CONTINUE.
5
Press =/+ until the track number you want
appears in the display.
You can create your program while checking the disc
labels
While the disc tray is open, follow Steps 1 to 6 with
pressing the DISC SKIP button to check the disc labels. If
you close the disc tray before Step 6, the total playing
time appears in the display after a while.
Track number
being programmed
Total playing time
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
TRACK
MIN
SEC
Note that, if the programmed track number isn’t found
on the disc, that step is automatically erased.
1 5 13.18CD1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
6
Press ENTER to select the track.
Checking the track order
You can check your program before or after you start
playing.
Last programmed
track
Playing order
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
Press CHECK.
TRACK
STEP
Each time you press this button, the display shows the
track (the disc and track numbers) or the disc (the disc
number and “AL” indication) of each step in the
programmed order. After the last step in the program,
the display shows “END” and returns to the original
display. If you check the order after you start playing,
the display shows only the remaining steps.
1 5 3
CD1
Programmed tracks
After one second
2
5
1
2
3
4
5
PROGRAM
DISC
A
8
TRACK
MIN
SEC
1 5 13.18CD1
Changing the track order
Total playing time
You can change your program before you start playing.
7
8
To program other discs or tracks, do the following:
You need to
To
Repeat Steps
2 through 4
5 and 6
To program
Press CHECK until the track
you don’t want appears in
the display, then press
CLEAR
Erase a track
Other discs
Other tracks on the same disc
Other tracks on other discs
2 through 6
Press CLEAR. Each time you
press the button, the last
track will be cleared.
Erase the last track in the
program
Press · to start Program Play.
Follow the programming
procedure
Add tracks to the end of the
program
To cancel Program Play
Press CONTINUE.
Hold down CLEAR until
“ALL CLEAR” appears in
the display. Create a new
program following the
programming procedure.
Change the whole program
completely
You can select a track directly using the number
buttons
Press the number button of the track in Step 5. To select a
track numbered over 10, use the >10 button (see page 13).
You can create your program while checking the disc
labels
While the disc tray is open, follow Steps 1 to 8 with
pressing the DISC SKIP button to check the disc labels. If
you close the disc tray before Step 8, the total playing
time appears in the display after a while.
Note that, if the programmed track number isn’t found
on the disc, that step is automatically erased.
Note
The total playing time doesn’t appear when:
—You have programmed a track whose number exceeds 20.
—The total playing time of the program exceeds 200 minutes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
To
You need to
Press P
Controlling Another CD Player
(Mega Control)
Pause
Stop play
Press p
AMS
Locate a disc while
the second player is
set to Continuous
Play mode
This unit can control a second CD player (see
“Connecting Another CD Player” on pages 6 and 7).
Even when a second CD player is connected, the
controls on both of the units will function. When you
press the play button on either unit, the operating
player stops and the resting player starts.
Turn ≠
until the
(DISC)
display shows the disc number
you want, then push
AMS
≠
(DISC)
Locate a track
Press 0 (–AMS+) ) until the
display shows the track number
you want
The controls indicated in the illustration below are effective
while the MEGA CONTROL button is lit.
• To do other operations, use the controls on the second
player or the supplied remote.
• The AMS buttons (=/+) and search buttons
(0/)) on the remote operate the second player as
indicated on the remote.
AMS
≠
(DISC)
Play mode buttons (CONTINUE/
·
P p
SHUFFLE/PROGRAM/REPEAT)
To control the second player directly using the supplied
remote
Set CD 1/2/3 on the remote to CD 3 which is the same
position as the COMMAND MODE selector on the rear panel
of the second player.
0 (–AMS+) )
MEGA CONTROL
1
Press MEGA CONTROL on this player.
The MEGA CONTROL button lights up and the
display shows the current disc number of the
second player.
To control this player again
Press MEGA CONTROL. The MEGA CONTROL button goes
off and you can control this player.
Notes
Current disc number
• You cannot locate a particular point in a track of the second
player using the controls on this player.
• Some controls on this player work on the second player
differently from they do to this player.
ALL DISCS
DISC
*DISC-1*
CD1
2
3
Select the play mode you want.
To program tracks, use the controls on the second
player.
Press · on this player to start playing.
The play starts and the display shows the current
disc and track numbers and the playing time of the
track.
While the MEGA CONTROL button is lit, you can
control the second player with the controls on this
player as follows:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g CDs
3
Press · to start playing.
The MEGA CONTROL button lights up while the
track in the second player is selected.
Playing Alternately (No-Delay
Play/X-Fade Play)
When you connect the second player, you can play
tracks in this player and those in the second player
alternately in any play mode (see “Connecting Another
CD Player” on pages 6 and 7).
To cancel No-Delay/X-Fade Play
Press the corresponding button repeatedly until the button
goes off. The current player continues playing.
Select one of the following methods:
You can change the method (No-Delay or X-Fade)
during play
Press the corresponding button (NO DELAY or X-FADE)
• No-Delay Play: The current player changes at each
track. Each time the current player changes to the
other player, the other player starts play without a
break in sound immediately after the current player
ends play. The other player skips the lead-in portion
and starts playing from where the sound actually
begins.
• X-Fade Play: The current player changes at each
track or at the specified interval. You can select the
interval among 30, 60 and 90 seconds. Each time the
current player changes to the other player, the sound
from both players is mixed. The current player ends
play by fading out, and the other player starts play
by fading in.
following the procedure in Step 2 above.
Notes
• The play starts from the second player if you start play
while the MEGA CONTROL button is lit.
• When one player has played all the discs/tracks in the
player ahead of the other player, the play stops.
• Do not use the controls on the second player during
No-Delay/X-Fade Play. They may not work correctly.
·
X-FADE
NO DELAY
1
2
Select the play mode you want on each player.
When you select No-Delay Play
Press NO DELAY.
The NO DELAY button lights up.
When you select X-Fade Play
Press X-FADE.
The X-FADE button lights up.
Each time you press the X-FADE button, the
indication appears as follows:
n FULL n 30 n 60 n 90 n OFF
To change the current player each time a whole
track is finished, select “FULL.”
To change the current player at the specified
interval, press X-FADE repeatedly until the
interval you want appears in the display.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g Fro m CDs
Recording a CD by Specifying
Tape Length (Time Edit)
(CDP-CE515 only)
Recording Your Own Program
You can record the program you’ve created on a tape,
etc. The program can contain up to 32 steps.
By inserting a pause during programming, you can
divide the program into two for recording on both
sides of a tape.
You can have the player create a program that will fit
the length of the tape.
The player automatically creates a program, keeping
the original order of the disc.
P
PROGRAM
DISC 1 – 5
·
The program can contain up to 32 steps (a pause
inserted between steps is counted as one step).
Note that tracks numbered over 20 cannot be
programmed automatically.
·P
DISC SKIP
≠ AMS
1
2
Create your program (for side A when recording
on a tape) while checking the total playing time
indicated in the display.
Follow Steps 1 through 5 in “Creating a program
0/)
EDIT/TIME FADE
on the player” on page 15.
A
The
indication appears in the display.
1
2
Press DISC SKIP to select the disc.
When you record on both sides of the tape, press
Press EDIT/TIME FADE repeatedly before you
start playing until “EDIT” appears and “A” in the
P to insert a pause.
A
B
The “PAUSE” and
indications appear in the
A
indication flashes in the display.
display and the playing time is reset to “0.00.”
When you record on one side of the tape, skip this
step and go to Step 4.
3
Press 0 or ) to specify the tape length.
Each time you press these buttons, the display
changes as shown below with the tape length of
one side.
A pause is counted as one step
You can program up to 31 steps when you insert a pause.
n C-46 23.00 N
n C-54 27.00 N
n C-60 30.00 N
3
4
Repeat Steps 2 through 5 in “Creating a program
on the player” to create the program for side B.
n - -. - - N
n C-74 37.00 N
n C-90 45.00 N
4
5
Press EDIT/TIME FADE to have the player create
the program.
Start recording on the deck and then press · on
the player.
Whenyourecordonbothsidesofthetape, theplayer
pauses at the end of the program for side A.
The display shows the tracks to be recorded. “B” in
B
the
indication flashes in the display.
When you record on both sides of the tape, press
EDIT/TIME FADE again.
The player inserts a pause, then creates the
program for side B. The display shows the
programmed tracks.
5
When you record on side B, reverse the tape and
press · or P on the player to resume playing.
To check and change your program
See page 17.
When you record on one side of the tape, skip this
step.
A
The
indication appears while checking the program
B
for side A and
B.
while checking the program for side
6
Start recording on the deck and then press · on
the player.
When you record on both sides of the tape, the
player pauses at the end of the program for side A.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g Fro m CDs
7
When you record on side B, reverse the tape and
press · or P on the player to resume playing.
Fading In or Out
You can manually fade the sound in or out to prevent
tracks from starting or ending abruptly.
Note that you cannot use this effect when you use the
DIGITAL OUT (OPTICAL) connector.
To cancel Time Edit
Press CONTINUE.
You can program the tracks you want in advance
Select the tracks before doing the above procedure. The
player creates a program from the remaining tracks.
·
P
You can freely specify the tape length
Set the tape length using the ≠ AMS
control.
Example: When the tape length of one side is 30 minutes
and 15 seconds
1 To set the minutes, turn ≠ AMS
until “30” appears in the display, then push
FADER
EDIT/TIME FADE* 0/)
≠ AMS
2 To set the seconds, turn ≠ AMS
.
*CDP-CE515 only
until
“15” appears in the display, then push
To
Press FADER
≠ AMS
.
FADE
Start play fading in
During pause.
lights up in
the display and the Q indication
flashes. The play fades in.
You can check and change the program
See page 17.
End play fading out
When you want to start fading out.
FADE
lights up in the display and
the q indication flashes. The play
fades out and the player pauses.
Note
Fading lasts for about 5 seconds. However, when you press
the FADER button during Music Scan (see page 13), the play
fades out for about 2 seconds.
Changing the fading time
You can change the fading time from 2 to 10 seconds
before fading in or out. If you don’t change it, fading
lasts for 5 seconds.
1
2
Press FADER before you start playing.
“FADE 5 SEC” appears in the display.
Press 0/) to specify the fading time.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g Fro m CDs
Fading out at the specified time
(Time Fade) (CDP-CE515 only)
Adjusting the Recording Level
(Peak Search) (CDP-CE515 only)
You can have the player fade out automatically by
specifying the playing time. Once you set the Time
Fade, it works twice, that is, the play fades out at the
end of both sides of a tape.
The player locates the highest level among the tracks to
be recorded to let you adjust the recording level before
you start recording.
1
Press EDIT/TIME FADE repeatedly before you
TIME
FADE
PEAK SEARCH
p
A
start playing until
and “A” in the
indication appear in the display.
2
Press 0 or ) to specify the playing time.
Each time you press these buttons, the display
changes as shown below with the playing time of
one side.
n C-46 23.00 N
n C-54 27.00 N
n C-60 30.00 N
1
Before you start playing, press PEAK SEARCH.
“PEAK” flashes in the display and the player
repeats the portion of the highest level.
n - -. - - N
n C-74 37.00 N
n C-90 45.00 N
3
4
Press · to start playing.
At the specified time the play fades out and the
B
player pauses. “B” in the
in the display.
indication appears
2
3
Adjust the recording level on the deck.
Press p on the player to stop Peak Search.
“PEAK” disappears from the display.
To record on side B, reverse the tape and press ·
or P on the player to resume playing.
Again, the play fades out at the specified time.
Notes
• The portion with the highest level may differ every time
you try the adjustment on the same disc. The difference is,
however, so slight that you won’t find any problem in
adjusting the recording level precisely.
To cancel Time Fade
Press EDIT/TIME FADE.
• Peak Search does not operate while you open the disc tray
by pressing the EX-CHANGE button.
You can freely specify the playing time
See “You can freely specify the tape length” on page 21.
You can change discs during Time Fade
If the play ends before the specified fade-out time, (for
example, when you record CD-singles on a tape) change
the disc. The specified fade-out time is counted only
during playing.
You can fade in to resume playing in Step 4
After you reverse the tape, press FADER.
Note
If you press the 0 or ) button during Time Fade Play,
Time Fade will be cancelled.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
St o rin g In fo rm a t io n Ab o u t CDs(Cu stomFiles)
Labeling discs on the player
What You Can Do With the
≠ AMS
Custom Files
The player can store two types of information called
“Custom Files” for each disc. Once you have stored
Custom Files for a disc, the player automatically recalls
what you have stored whenever you select the disc.
Note that Custom Files will be erased if you do not use
CLEAR
MEMO INPUT
the player for about one month.
1
2
Insert or select the disc.
You can store this information:
Press MEMO INPUT.
The flashing cursor (“) appears.
You can
When you use
Label discs using up to 12
characters
Disc Memo (page 23)
3
Turn ≠ AMS
appears in the display.
The cursor disappears and the first space for the
Disc Memo flashes.
until the character you want
Delete unwanted tracks and store
only the tracks you want
Delete Bank (page 25)
As you turn ≠ AMS
characters appear in the following order. Turn
≠ AMS counterclockwise to go back to the
clockwise, the
Where are Custom Files stored?
previous character.
Custom Files are stored not on the disc, but in the
player’s memory. It means you cannot use Custom
Files when you play the disc on other players.
(space) A B C D E F G H I J K L M N O P Q R S T U
V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w
x y z 0 1 2 3 4 5 6 7 8 9 ! " # $ % & ' ( ) *+ , – . / : ; <
-
= > ? @ [ \ ] ^ _ || { | }
Erasing all Custom Files of all discs
ALL DISCS
Turn off the player. While holding down CLEAR, press
POWER to turn on the player. “ALL ERASE” appears
in the display, and all Custom Files will be erased.
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
S
CD1
4
Push ≠ AMS
to select the character.
The selected character lights up, and the flashing
cursor appears to indicate the next space to be
input.
Labeling Discs (Disc Memo)
You can label discs using up to 12 characters and have
the player display the Disc Memo each time you select
the disc. The Disc Memo can be anything you like, such
as a title, musician’s name, category or date of
purchase.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
S
CD1
If you have made a mistake
Press CLEAR and begin again by inputting the correct
characters.
When you select a CD-TEXT disc
The disc title is stored as the Disc Memo automatically.
If the disc title has more than 12 characters, the first 12
characters of the disc title are stored (see page 11).
Note that you cannot change the Disc Memo of the CD-
TEXT disc.
5
Repeat Steps 3 and 4 to input more characters.
(Continued)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
St o rin g In fo rm a t io n Ab o u t CDs (Cu st o m File s)
6
Press MEMO INPUT to store the Disc Memo.
The Disc Memo lights up in the display.
&!?
ABC
JKL
TUV
QZ
DEF
GHI
PRS
MNO
WXY
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
Symphony No1CD1
Repeat Steps 1 to 6 to assign Disc Memos to other
discs.
>
10
ENTER
Characters assigned to
each number button
Labeling discs using the remote Z
Example: To select the letter E
Press the number button 3 twice.
n D n E n F
SPACE
Press 3.
Press 3.
DEL
CAPS
Press 3.
Number
buttons
To insert a space, press SPACE once.
To input a number, press CAPS twice in Step 4,
then press the number button you want.
To input symbols, press the number button 1
repeatedly until the symbol you want appears in
the display.
ENTER
CLEAR
MEMO INPUT
0/)
6
Press ENTER to select the character.
The selected character lights up, and the flashing
cursor appears to indicate the next space to be
input.
You can also go to the next space by pressing other
number buttons.
1
2
Press CAPS.
Press the number button of the disc you want to
assign a Disc Memo, and then ENTER.
3
4
Press MEMO INPUT.
The flashing cursor (“) appears.
7
8
Repeat Steps 4 through 6 to input more characters.
Press CAPS to find the letter type you want.
Each time you press the button, the letter type
changes cyclically among capital letters (ABC),
small letters (abc) and numbers (123).
Press MEMO INPUT to store the Disc Memo.
The Disc Memo lights up in the display.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
5
Press the number button corresponding to the
character you want (indicated beside each number
button).
Symphony No1CD1
Repeat Steps 1 through 8 to assign Disc Memos to
other discs.
The cursor disappears and the first space for the
Disc Memo flashes.
Each time you press the button, the character
changes cyclically among the ones indicated
beside the button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
St o rin g In formatio nAbout CDs (Cust omFiles)
If you have made a mistake while inputting the
character
Storing Specific Tracks
(Delete Bank)
To correct the character which has been input
1 Press 0 or ) until the cursor moves next to the
incorrect character.
You can delete unwanted tracks and store only the
tracks you want. When you select the disc containing a
Delete Bank, you can play only the remaining tracks.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
Symphe y No1CD1
CONTINUE SHUFFLE
2 Press DEL to delete the incorrect character.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
Symph y No1
CD1
CHECK
CLEAR
3 Input the correct character.
1
2
Insert or select the disc.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
10
DISC
Press CONTINUE or SHUFFLE before you start
playing.
Symphony No1CD1
To correct the character currently being input
1 Press DEL to delete the incorrect character.
2 Input the correct character.
3
Press CHECK repeatedly until the track you want
to delete appears in the display.
ALL DISCS
1
6
2
7
3
8
4
9
5
1
2
3
4
5
To insert a character between the input characters
10
DISC
TRACK
Press 0 or ) until the cursor moves next to the point
you want to insert, and enter the character.
1 1 ON
CD1
4
Press CLEAR.
“DELETE” and “OFF” appear in the display.
Erasing the Disc Memo
ALL DISCS
2
7
3
8
4
5
1
Follow Steps 1 and 2 in “Labeling discs on the
player” on page 23 to select the Disc Memo you
want to erase.
1
2
3
4
5
DELETE
6
9
10
DISC
TRACK
1 1 OFF
CD1
2
3
Press CLEAR.
The Disc Memo disappears.
If you want to recover the track, press CLEAR
again.
Press MEMO INPUT.
5
Repeat Steps 3 and 4 to delete more tracks.
You can recover all the tracks you have deleted
Hold down CLEAR until “ALL SELECT” appears in the
display.
Note
The deleted tracks are skipped even in the Shuffle or Program
Play mode (when the whole disc containing a Delete Bank is
programmed as one step).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Precautions
Notes on CDs
On safety
On handling CDs
• Caution — The use of optical instruments with this product
• To keep the disc clean, handle the disc by its edge. Do not
touch the surface.
• Do not stick paper or tape on the disc.
will increase eye hazard.
• Should any solid object or liquid fall into the cabinet,
unplug the player and have it checked by qualified
personnel before operating it any further.
On power sources
• Before operating the player, check that the operating
voltage of the player is identical with your local power
supply. The operating voltage is indicated on the nameplate
at the rear of the player.
Not this w ay
• The player is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the player itself has been turned off.
• If you are not going to use the player for a long time, be
sure to disconnect the player from the wall outlet. To
disconnect the AC power cord (mains lead), grasp the plug
itself; never pull the cord.
• Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in direct
sunlight as there can be considerable rise in temperature
inside the car.
• Do not use any commercially available stabilizer. If you do,
the disc and the player may be damaged.
• After playing, store the disc in its case.
• AC power cord must be changed only at the qualified
service shop.
On cleaning
On placement
• Before playing, clean the disc with a cleaning cloth. Wipe
• Place the player in a location with adequate ventilation to
the disc from the center out.
prevent heat build-up in the player.
• Do not place the player on a soft surface such as a rug that
might block the ventilation holes on the bottom.
• Do not place the player in a location near heat sources, or in
a place subject to direct sunlight, excessive dust or
mechanical shock.
On operation
• If the player is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture may
condense on the lenses inside the player. Should this occur,
the player may not operate properly. In this case, remove
the disc and leave the player turned on for about an hour
until the moisture evaporates.
• Do not use solvents such as benzine, thinner, commercially
available cleaners or anti-static spray intended for vinyl
LPs.
On adjusting volume
• Do not turn up the volume while listening to a portion with
very low level inputs or no audio signals. If you do, the
speakers may be damaged when a peak level portion is
played.
On cleaning
• Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any questions or problems concerning your
player, please consult your nearest Sony dealer.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Troubleshooting
Specifications
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
Compact disc player
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output
Max 44.6 µW*
* This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
There’s no sound.
/Check that the player is connected securely.
/Make sure you operate the amplifier correctly.
/Adjust the playback level using the LINE OUT
LEVEL +/– buttons on the remote.
Frequency response
Signal-to-noise ratio
Dynamic range
2 Hz to 20 kHz 0.5 dB
More than 107 dB
More than 98 dB
The CD does not play.
/There’s no CD inside the player (“–NO DISC–”
appears). Insert a CD.
Harmonic distortion
Less than 0.0035%
/Place the CD with the label side up on the disc
tray correctly.
Output
Load
impedance
Jack
type
Maximum
output
level
/Clean the CD (see page 26).
/Moisture has condensed inside the player.
Remove the disc and leave the player turned on
for about an hour (see page 26).
/Place the CD in the correct position on the disc
tray.
Over 10 kilohms
LINE OUT
Phono
jacks
2 V
(at 50 kilohms)
Wave length: 660 nm
DIGITAL OUT Optical
–18 dBm
(OPTICAL)
output
connector
The remote does not function.
PHONES
Stereo
phone jack
32 ohms
10 mW
/Remove the obstacles in the path of the remote
and the player.
/Point the remote at the remote sensor g on the
player.
General
/Replace all the batteries in the remote with new
ones if they are weak.
/Set the CD 1/2/3 switch on the remote
according to the position of the COMMAND
MODE selector at the rear panel of the player.
Power requirements
Where purchased
USA/Canada
Europe
Power requirements
120 V AC, 60 Hz
220 V – 230 V AC, 50/60 Hz
240 V AC, 50/60 Hz
Australia
The player functions incorrectly.
/The microcomputer chips may be operating
incorrectly. Turn the power off, then turn it
back on to reset the player.
Power consumption
14 W
Dimensions (approx.)
(w/h/d)
430 × 120 × 393 mm
(17 × 4 3/4 × 15 1/2 in.) incl. projecting
parts
Mass (approx.)
5.4 kg (11 lbs 15 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Remote commander (remote) (1)
Sony SUM-3 (NS) batteries (2)
Design and specifications are subject to change without notice.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
Program 15
changing 17
checking 17
for recording 20
Names of controls
Index
Bu t t o n s
A, B
CAPS 24
R
S
T
AMS 13
CHECK 17
CLEAR 17
Recording 20
a program 20
using Time Edit 20
Remaining time 10
Automatic Music Sensor. See
AMS
CONTINUE
X-FADE 19
DISC 12
8
C, D
Remote control
Repeating 14
4
CD-TEXT 11
Connecting
another CD player
Continuous Play
Controlling another CD
player 18
X-Fade Play 19
Custom Files
Delete Bank 25
Disc Memo 23
what you can do with 23
DISC 1 – 5 12
4
DISC CHECK 12
DISC SKIP 12
EDIT/TIME FADE 20, 22
ENTER 12
EX-CHANGE 12
FADER 21
HIGH-LIGHT 11
LINE OUT LEVEL +/–
MEGA CONTROL 18
MEMO INPUT 23
MUSIC SCAN 13
NO DELAY 19
Number 13
§ OPEN/CLOSE
Replacing discs while playing
a disc 12
6
8
Scanning. See Music Scan
Searching. See Locating
Select Shuffle Play 15
Shuffle Play 14
Storing
information about CDs 23
specific tracks 25
5
E
Editing. See Recording
Erasing
Custom Files 23
Delete Bank 25
Disc Memo 25
8
Time Edit 20
Time Fade 22
Total playing time 10
Troubleshooting 27
PEAK SEARCH 22
PROGRAM 15
REPEAT 14
SHUFFLE 14
TIME/TEXT 10
F, G
U, V, W, X, Y, Z
Fading 21
Time Fade 22
Unpacking
4
·
P
p
9
9
9
H, I, J, K
0/) 14
0 (–AMS+) ) 18
=/+ 13
> 10 13
Handling CDs 26
Hookups
overview
4
4
L
Labeling a disc 23
Locating
Co n t ro l
AMS
≠
13, 18
(DISC)
by monitoring 14
by observing the
display 14
by scanning 13
directly 13
Ja ck
PHONES
8
using AMS 13
while checking the
labels 12
Sw it ch
POWER
8
M
Ot h e rs
Mega Control 18
Music Scan 13
Disc tray
8
Display 10
N, O
g
4
No-Delay Play 19
P, Q
Peak Search 22
Playback
Continuous Play
X-Fade Play 19
8
No-Delay Play 19
Playing alternately 19
Program Play 15
Repeat Play 14
Shuffle Play 14
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|