Solid State Logic
S O U N D
V I S I O N
||
SUPERANALOGUE
X - R A C K
Super-Analogue™ Outboard
X-Rack Mic Amp User’s Guide
This documentation package contains the User’s Guide for your new X-Rack Mic Amp
module. Depending on the age of your X-Rack, these pages may already be present in
your X-Rack Owner’s Manual – please check to see if these pages match your Manual.
If they do not, these pages should be filed alongside it.
Please Note. X-Rack units prior to serial number XRK0110 are not 100% compatible with the X-Rack Mic
Amp as these units can not provide +48V phantom power unless field retrofit kit 629620XR
has been fitted. This kit is available free-of-charge from your local distributor, if the X-Rack unit
concerned is in warranty. For units that are out of warranty a small charge will be made. The
absence of this kit is indicated by the buscard in the X-Rack being a ‘629620X1 RE 1’ (rev 1),
with a number of components (ie. ‘IC2’, ‘C4’, ‘L4’) missing.
For correct operation of Total Recall™, your X-Rack unit must be running V1.1/0 or later
software. Please refer to your X-Rack Owners Manual for instructions on how to check the
current software version and how to obtain and install a newer version if required.
There may be a newer version of the X-Rack Owner’s Manual available for download from our
82S6XR0A0B
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Mic Amp Module
A. The Mic Amp Module
A.1 Connection
The rear panel of the module carries the Mic (‘IN’) and Line input (‘LINE’) XLRs along
with a single output (‘OUT’) XLR. The Line input and output operate at a nominal
level of +4dBu although the gain of the Line input can be varied by a front panel
control. Also contained on the front panel is an additional mono Jack socket for a high
impedance Instrument input.
IN
LINE
OUT
A.2 Operation
The X-Rack Mic module contains three seperate input amplifiers; a Microphone
amplifier, an Instrument input and a Line input, any one of which may be selected
at any one time. A set of High and Low Pass filters are also provided.
XR621
SEL
MIC
INST
1
1
A.2.1 MIC Section
Normally, the Microphone input on the rear of the module will be selected (‘LINE’
and ‘INST’ switches released); pressing the ‘INST’ switch selects the mono jack
instrument input on the front of the module. This is a very high impedance
unbalanced input intended to be used with guitar pickups etc. To help alleviate
‘hum’, a ground lift (‘GND LFT’) switch has been provided which places a 1k2Ω
impedance in series with the sleeve of this connector and audio ground in the
module. The gain of these inputs is continuously variable between +12dB and
+75dB.
IMP
IN
LO
HI
Z
+48V
PAD
+12
+75
+20
dB
dB
LINE
LINE
2
-20
9
Ø
HF
The impedance of the Microphone input can be varied between ≈1k2Ω and ≈10kΩ
by selecting the ‘IMP IN’ switch and adjusting the ‘Z’ control. This allows the
connection of line level signals to the Microphone input if required, and provides an
alternative input impedance for some dynamic microphones.
6
30
60
4
IN
50
3
KHz
LF
160
300
The ‘PAD’ switch reduces the signal level of both the Microphone or Instrument
inputs by 20dB. Phantom power, for microphones requiring this, can be switched on
using the ‘+48V’ switch. Please note that X-Rack units prior to serial number XRK0110
are not normally enabled for +48V. However, a field retrofit kit (629620XR) is available for
these units. Any in-warranty X-Rack units can be upgraded free-of-charge; for units out of
warranty a charge will be made. Please contact your local distributor to order this kit, if
required.
IN
30
600
OUTPUT
SIGNAL
REC
L
REC
R
INSTRUMENT
GND
LIFT
Note. Please note that connecting a microphone to the X-Rack Mic module with phantom power
switched on is not advised as it may cause damage to either the microphone or the input
stage of the X-Rack module. Take care not to connect line level sources (keyboards etc.) to the
microphone input with phantom power switched on as this may damage the output stage of
the connected unit.
2
A.2.2 LINE Section
The Line input on the rear of the module is selected by pressing the ‘LINE’ switch. The gain of this input
can be varied by 20dB from the nominal 0dB.
The Ø (Phase) switch reverses the phase of the selected input.
Page A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Owner’s Manual
3
A.2.3 HF/LF Section
XR621
This section contains simple high and low pass filters as follows:
SEL
HF (Low Pass):
LF (High Pass):
Frequency range 50kHz – 3kHz (–3dB point)
Slope: 12dB/Octave
MIC
INST
Frequency range 30Hz – 600Hz (–3dB point)
Slope: 18dB/Octave
IMP
IN
LO
HI
Z
The two filters can be switched into circuit independently.
+48V
PAD
4
A.2.4 OUTPUT Section
+12
+75
+20
dB
dB
LINE
LINE
This small section contains a tri-colour signal present indicator and two routing
switches (‘REC L’ and ‘REC R’) which route the module signal onto a common
internal record bus.
-20
9
Ø
HF
The signal present indicator measures signals immediately prior to the output
amplifier. It will light GREEN for output signals above the lower threshold of
–60dBu, AMBER for signals between +4dBu and +24dBu and lights RED for signals
above +24dBu.
6
30
60
4
IN
3
50
3
KHz
LF
300
160
The record bus is not currently used but may be used by forthcoming X-Rack
modules (such as the XR622 Mix/Monitor Module, due late 2006).
IN
30
600
OUTPUT
SIGNAL
REC
L
REC
R
4
INSTRUMENT
GND
LIFT
Page A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Mic Amp Module
A.3 Performance Specification
The following pages contain audio performance specification figures for the X-Rack Mic Amp module. No
other Solid State Logic products are covered by this document and the performance of other Solid State
Logic products can not be inferred from the data contained herein.
A.3.1 Measurement Conditions
For each set of figures on the following pages, the specific unit and test setup will be stated at the
beginning of that section. Any changes to the specified setup for any particular figure(s) will be detailed
beside the figures to which that difference applies.
A.3.2 Measurement References
Unless otherwise specified the references used in this specification are as follows:
• Reference frequency:
1kHz
• Reference level:
0dBu, where 0dBu ≈ 0.775V into any load
• Source impedance of Test Set:
• Input impedance of Test Set:
50Ω
100kΩ
• All unweighted measurements are specified as 22Hz to 22kHz band limited RMS and are expressed in
units of dBu
• All distortion measurements are specified with a 36dB/Octave low pass filter at 80kHz and are
expressed as a percentage
• The onset of clipping (for headroom measurements) should be taken as 1% THD
• Unless otherwise quoted all figures have a tolerance of 0.5dB or 5%
• All measurements are made with the operating level switch set for +4dBu
A.3.3 Microphone Amplifier Performance
Signal applied to Microphone Input and measured at Output. Pad switched out and Input Gain control
set to +12dB (minimum).
Gain
Continously variable from +12dB to +75dB
Independently switchable 20dB Pad available
Input Impedance
Output Headroom
Continously variable from ≈1k2Ω to ≈10kΩ
> +26dBu at onset of clipping
THD + Noise
(-18dBu applied, +28dB gain)
< 0.003% at 1kHz
< 0.006% at 10kHz
Frequency Response
+0.05dB/-0.1dB from 20Hz to 20kHz
–3dB at 150kHz
Equivalent Input Noise
< –127dB at maximum gain
(input terminated with 150Ω)
< –90dB at 0dB gain (+20dB with Pad ‘IN’)
Common Mode Rejection
(-10dBu applied, +30dB gain)
> 75dB from 50Hz to 1kHz
> 70dB at 10kHz
Page A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Owner’s Manual
A.2.4 Instrument Input Performance
Un-balanced signal applied to Instrument Input and measured at Output. Pad switched out and Input
Gain control set to +12dB (minimum).
Gain
Continously variable from +12dB to +75dB
Independently switchable 18dB Pad available
Input Impedance
Output Headroom
1MΩ
> +26dBu at onset of clipping
THD + Noise
(-18dBu applied, +28dB gain)
< 0.03% at 1kHz
< 0.05% at 10kHz
Frequency Response
+0.05dB/-0.1dB from 20Hz to 20kHz
–3dB at 150kHz
Equivalent Input Noise
(Input terminated with 150Ω)
< –82dB at +12dB (minimum) gain
< –88dB at +28dB gain (mid’ position)
A.2.5 Line Input Performance
Signal applied to Line Input and measured at Output. Input Gain control set to 0dB (indent).
Gain
Continuously variable from –20dB to +20dB
> 10kΩ
Input Impedance
THD + Noise
< 0.005% from 20Hz to 20kHz
(+24dBu applied, 0dB gain)
Frequency Response
0.1dB from 20Hz to 20kHz
–3dB at 150kHz
Equivalent Input Noise
< –90dB
(Input terminated with 150Ω)
Page A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Mic Amp Module
A.4 Calibration Information
The X-Rack Mic Amp module is factory calibrated and should only need calibration if a potentiometer or
other component has been replaced or if it is suspected that there is a problem with calibration.
In each of the following instructions it is assumed that the lid of the X-Rack has been removed and that
power has been applied. It is also assumed that unless otherwise specified, all switches are released and
all front panel potentiometers are at unity or minimum position as appropriate. The required accuracy for
each adjustment will be specified along with the target value. All level and distortion measurements
should be made with audio-band 20Hz to 20kHz filters unless otherwise specified.
All presets are accessible from the top of the unit.
A.4.1 Microphone Input
Equipment Required:
Calibrated audio oscillator and audio level meter
50Hz sinewave @ –12dBu, common mode
Test Signal:
Input and Output:
Unit Setup:
Oscillator to Mic Input and Output to the audio level meter
Set the Mic Gain to ‘36dB’ (mid-position)
CMRR Trim
Adjustment:
Adjust VR7 (CMRR) for minimum level (normally < –40dBu)
A.4.2 Line Input
Equipment Required:
Test Signal:
Calibrated audio oscillator and audio level meter
1kHz sinewave @ 0dBu
Input and Output:
Unit Setup:
Oscillator to Line Input and Output to the audio level meter
Set the Line Gain to indent (0dB) and select ‘LINE’
Level Trim
Adjustment:
1. Adjust VR6 (0dB) for 0dBu 0.05dB.
A.4.3 Output Balance
Equipment Required:
Calibrated audio oscillator, audio level meter and a ‘balance’ adaptor (see
below)
Test Signal:
1kHz sine wave at +24dBu
Input and Output:
Oscillator to Line Input and Output to the audio level meter via the
‘balance’ adaptor
Unit Setup:
Adjustment:
Set the Line Gain to indent (0dB) and select ‘LINE’
Adjust VR8 (BAL) for minimum level (< 55dBr)
A.4.4 ‘Balance’ Adaptor
For the output balance adjustment, a ‘balance’
adaptor such as that illustrated here will be
required. This adaptor consists of a pair of close
tolerance resistors in an in-line cable and is
used to sum together a balanced output in
order to correctly adjust the level balance of the
measured output; perfect balance should result
in complete signal cancellation.
1
2
3
3
2
1
0V
+
–
1
1
5K01**
5K01**
From unit
under test
To measuring 2
equipment
+
–
0V
1.
2.
Note
Resistor tolerance should ideally be 0.01%
Absolute level measured will depend upon the input
impedence of the measuring equipment.
Page A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Rack Owner’s Manual
A.5 Connector Details
Audio Input
Audio Output
Location:
Rear Panel
Location:
Rear Panel
Conn' Type: XLR Male
Conn' Type: XLR Female
Pin
Description
Pin
Description
1
Chassis
1
Chassis
2
Audio +ve
Audio -ve
2
Audio +ve
Audio -ve
3
3
Instrument Input
Location:
Front Panel
Conn' Type: Mono 1/4" Jack Socket
Pin
Description
Tip
Sleeve
Guitar Input
Chassis
A.6 Physical Specification *
Depth:
200mm / 7.9 inches
275mm / 10.9 inches
including front panel knobs, excluding connectors
including front panel knobs and connectors
Height:
Width:
171mm / 6.75 inches
35mm / 1.4 inches
49mm / 1.9 inches
front/rear panels
overall width (front and rear panels are offset)
Weight:
260g / 9.5 ounces
Boxed size:
190mm x 290mm x 70mm / 7.5" x 11.5" x 2.5"
460g / 16.5 ounces
Boxed weight:
* All values are approximate
A.7 Environmental Specification
As per X-Rack – see page 17.
Page A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|