OPERATOR’S
MANUAL
Large Frame
Snowthrowers
1226 Models
1632 Models
Mfg. No.
1695324
1695325
1695326
1695327
Description
Mfg. No.
1695336
1695337
1695338
Description
L1226E, Snowthrower
L1226EX, Snowthrower (CE)
L1226E, Snowthrower
L1226EX, Snowthrower (CE)
1632E, Snowthrower
1632EX, Snowthrower (CE)
L1632E, Snowthrower
1428 Models
Mfg. No.
1695328
1695329
1695330
1695331
Description
L1428E, Snowthrower
L1428EX Snowthrower (CE)
L1428E, Snowthrower
L1428EX Snowthrower (CE)
1530 Models
Mfg. No.
1695332
1695333
1695334
1695335
Description
L1530E, Snowthrower
L1530EX, Snowthrower (CE)
L1530E, Snowthrower
L1530EX, Snowthrower (CE)
1734892
Revision 02
Rev. Date 11/2007
TP 100-4613-02-LW-SN
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
Operating Safety
Congratulations on purchasing a superior-quality piece of lawn
and garden equipment. Our products are designed and manu-
factured to meet or exceed all industry standards for safety.
Power equipment is only as safe as the operator. If it is mis-
used, or not properly maintained, it can be dangerous!
Remember, you are responsible for your safety and that of
those around you.
Use common sense, and think through what you are doing. If
you are not sure that the task you are about to perform can be
safely done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.
Read the Manual
The operator’s manual contains important safety information you need
to be aware of BEFORE you operate your unit as well as DURING
operation.
Safe operating techniques, an explanation of the product’s features
and controls, and maintenance information is included to help you
get the most out of your equipment investment.
Be sure to completely read the Safety Rules and Information found on
the following pages. Also completely read the Operation section.
Children
DO NOT ALLOW CHILDREN TO OPERATE THIS UNIT!
Tragic accidents can occur with children. Do not allow
them anywhere near the area of operation. Children are
often attracted to the unit and snowthrowing activity.
Never assume that children will remain where you last
saw them. If there is a risk that children may enter the
area where you are operating the unit, have another
responsible adult watch them.
This encourages them to come near the unit in the future
while it is running, and they could be seriously hurt.
They may then approach the unit when you are not
expecting it, and you may run over them.
TP 600-3606-05-LW-SMA
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
Moving Parts
This equipment has many moving parts that can injure you or someone else.
However, if you are standing in the operator’s position, and follow all the rules in
this book, the unit is safe to operate.
The auger and impeller have spinning parts that can amputate hands and feet.
Do not allow anyone near the equipment while it is running! DO NOT clear the
discharge chute by hand. If the chute becomes plugged, stop the engine, wait for
all moving parts to stop, and clear the blockage with a clean-out tool or piece of
wood.
To help you, the operator, use this equipment safely, it is equipped with an
operator-present safety system. Do NOT attempt to alter or bypass the system.
See your dealer immediately if the system does not pass all the safety interlock
system tests found in this manual.
Thrown Objects
This unit has a spinning auger and impeller. They
pick up and throw snow and ice. Thrown debris
could seriously injure a bystander. ALWAYS direct
the discharge chute away from bystanders and prop-
erty that could be damaged by flying debris. Be sure
to clean up the area to be cleared BEFORE you
start.
Do not allow anyone in the area while the unit is run-
ning! If someone does enter the area, shut the unit
off immediately until they leave.
Fuel and Maintenance
Gasoline is extremely flammable. Its vapors are also
extremely flammable and can travel to distant ignition
sources. Gasoline must only be used as a fuel, not as a
solvent or cleaner. It should never be stored any place
where its vapors can build up or travel to an ignition source
like a pilot light. Fuel belongs in an approved, plastic,
sealed gas can, or in the snowthrower fuel tank with the
cap securely closed. Spilled fuel needs to be cleaned up
immediately.
Proper maintenance is critical to the safety and perfor-
mance of your unit. Be sure to perform the maintenance
procedures listed in this manual, especially periodically
testing the safety system.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and
follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury
or death to you, or bystanders, or damage to property or equipment. The triangle
important cautions or warnings which must be followed.
in text signifies
TRAINING
OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manuals before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic.
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the
cord on electric motors, thoroughly inspect the
snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the
collector/impeller housing or discharge guide, and
when making any repairs, adjustments, or inspec-
tions.
6. When cleaning, repairing, or inspecting make certain
the collector/impeller and all moving parts have
stopped. Disconnect the spark plug wire and keep
the wire away from the plug to prevent accidental
starting.
7. Do not run the engine indoors except for starting the
engine or for transporting the snowthrower in or out of
the building. Open the outside doors; exhaust fumes
are dangerous.
8. Exercise extreme caution when operating on slopes.
Do not attempt to clear steep slopes.
9. Never operate the snowthrower without proper
guards plates, or other safety protective devices in
place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when operating in reverse.
13. Disengage power to the collector/impeller when
snowthrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snowthrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snowthrower without good visibility
or light. Always be sure of your footing, and keep a
firm hold on the handles. Walk, never run.
16. Never touch a hot engine or muffler.
17. Never operate the snowthrower near glass enclo-
sures, automobiles, window wells, drop-offs, and the
like without proper adjustment of the discharge angle.
18. Never direct discharge at bystanders or allow anyone
in front of the unit.
3. Keep the area of operation clear of all persons, partic-
ularly small children and pets.
4. Exercise caution to avoid slipping or falling especially
when operating in reverse.
PREPARATION
1. Thoroughly inspect the area where the equipment is
to be used and remove all doormat, sleds, boards,
wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting engine (motor).
3. Do not operate the equipment without wearing ade-
quate winter outer garments. Wear footwear that will
improve footing on slippery surfaces. Avoid loose fit-
ting clothing that can get caught in moving parts.
4. Handle fuel with care; it is highly flammable.
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors. Replace fuel cap securely and
wipe up spilled fuel.
(d) Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place con-
tainers on the ground, away from your vehicle, before
filling.
(e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground. If
this is not possible, then refuel such on a trailer with a
portable container, rather than from a gasoline dis-
penser nozzle.
(f) Keep nozzle in contact with the rim of the fuel tank
or container opening at all times, until refueling is
complete. Do not use a nozzle lock-open device.
(g) Replace gasoline cap securely and wipe up spilled
fuel.
(h) If fuel is spilled on clothing, change clothing imme-
diately.
5. Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive
motors or electric starting motors.
6. Adjust the collector housing height to clear gravel or
crushed rock surfaces.
7. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by the manufacturer).
8. Let engine (motor) and machine adjust to outdoor
temperatures before starting to clear snow.
9. Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair
to protect eye from foreign objects that may be
thrown from the machine.
19. Never leave a running unit unattended. Always disen-
gage the auger and traction controls, stop engine,
and remove keys.
20. Do not operate the unit while under the influence of
alcohol or drugs.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
21. Keep in mind the operator is responsible for acci-
dents occurring to other people or property.
8. Always follow the engine manual instructions for stor-
age preparations before storing the unit for both short
and long term periods.
9. Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
10. Maintain or replace safety and instruction labels as
necessary.
11. Keep nuts and bolts tight and keep equipment in
good condition.
12. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
22. Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the unit safely enough
to protect themselves and others from injury.
23. DO NOT wear long scarves or loose clothing that
could become entangled in moving parts.
24. Snow can hide obstacles. Make sure to remove all
obstacles from the area to be cleared.
CHILDREN
13. Components are subject to wear, damage, and dete-
rioration. Frequently check components and replace
with manufacturer’s recommended parts, when nec-
essary.
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the operating activity. Never assume that children will
remain where you last saw them.
14. Check control operation frequently. Adjust and ser-
vice as required.
1. Keep children out of the area and under the watchful
15. Use only factory authorized replacement parts when
making repairs.
care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
16. Always comply with factory specifications on all set-
tings and adjustments.
17. Only authorized service locations should be utilized
for major service and repair requirements.
18. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper ser-
vice procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hand to clean
out the discharge chute.
19. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
To clear the chute:
1. SHUT OFF THE ENGINE.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. If available, look for the relevant Emissions Durability
Period and Air Index information on the engine emis-
sions label.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean out tool, not your hands.
SERVICE, MAINTENANCE, AND STORAGE
1. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water and spacer heaters, or clothes dry-
ers. Allow the engine to cool before storing in any
enclosure.
IGNITION SYSTEM
1. This spark ignition system complies with Canadian
ICES-002.
3. Always refer to the operator’s manual for important
details if the snowthrower is to be stored for an
extended period.
4. Maintain or replace safety and instruction labels as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
6. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
7. Always observe safe refueling and fuel handling prac-
tices when refueling the unit after transportation or
storage.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Decals
DECALS
The safety decals below are on your unit.
This unit has been designed and manufactured to pro-
vide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment.
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
Although reading this manual and safety instructions it
contains will provide you with the necessary basic knowl-
edge to operate this equipment safely and effectively, we
have placed several safety labels on the unit to remind
you of this important information while you are operating
your unit.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective, operation.
NOTE: Engine operation and safety decals are supplied
by the engine manufacturer.
All WARNING, CAUTION, and instructional messages
on your unit should be carefully read and obeyed.
Personal bodily injury can result when these instructions
are not followed. The information is for your safety and it
is important.
NORTH AMERICAN MODEL DECALS
Part No. 1733056 - DANGER / WARNING
Main Dash Decal, North American, w/o Easy Turn
Part No. 1733033 - DANGER / WARNING
Main Dash Decal, North American, w/ Easy Turn
The lubrication points shown here must be lubricated
with 30 weight oil every 10 hours of operation, and
before using the unit after storage. Failure to lubricate
DANGER
WARNING
DANGER
Amputation hazard
Required maintenance may cause a malfunction of the safety system.
Amputation hazard
1733526
Contact with the auger will cause
serious injury.
Contact with moving parts
• Keep hands, feet, and clothing
inside chute will cause
away.
serious injury.
• Shut off engine before servicing.
1716532
Part No. 1733526
Lubrication Decal
Shut off engine before
unclogging discharge chute.
Use clean-out tool, not hands!
1733057
Part No. 1716532
Auger Danger
Decal
Part No. 1733057
Discharge Chute
Danger Decal
“V” BELTS STRETCH
UNDER NORMAL
USE WHICH WILL
AFFECT DISCHARGE
PERFORMANCE AND
SHOULD BE
PERIODICALLY
ADJUSTED. REFER
TO MANUAL FOR
INSTRUCTIONS.
Part No. 728183
Important
Over Adjustment
Part No. 725432
Belt Stretch &
Adjust
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Decals
ALL MODEL DECALS
Part No. 1733443
Chute Release
Part No. 1733772
Shift Decal
CE MODEL DECALS
Part No. 1733060 - DANGER / WARNING
Main Dash Decal, CE, w/ Easy Turn
Part No. 1733059 - DANGER / WARNING
Main Dash Decal, CE, w/o Easy Turn
Part No. 1727208
Auger Danger Decal
Part No. 1727207
Discharge Chute
Danger Decal
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Icons
SAFETY ICONS
WARNING: READ OPERATOR’S
MANUAL.
WARNING: DISMEMBERMENT.
This machine can amputate limbs.
Keep bystanders and children away
when engine is running.
Read and understand the Operator’s
Manual before using this machine.
DANGER: DISMEMBERMENT.
DANGER: THROWN OBJECTS.
The auger can amputate limbs. Keep
hands and feet away from auger and
rotating parts.
This machine is capable of throwing
objects and debris. Keep bystanders
away.
WARNING: REMOVE KEY BEFORE
SERVICING.
DANGER: DISMEMBERMENT.
The impeller can amputate limbs.
Stop the engine, remove the key, and
disconnect spark plug wire before
clearing the discharge chute or per-
forming service work. Keep hands
and feet away from impeller and rotat-
ing parts.
Remove the key, disconnect spark
plug wire, and consult technical litera-
ture before performing repairs or
maintenance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification Numbers
North American /
CE Models
Part No. xxxxx
CE Models
(Only)
xxxxxxxxxxxxxx
Serial No. xxxxxxxxxx
xxx
dB
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
kg: xxx
PRODUCT REFERENCE DATA
Model Description Name/Number
kW: x.xx
20xx
xxxx max
Identification Numbers
Unit MFG Number
Unit SERIAL Number
When contacting your authorized dealer for replace-
ment parts, service, or information you MUST have
these numbers.
Date Purchased
Dealer Name
Record your model name/number, manufacturer’s identi-
fication numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
ENGINE REFERENCE DATA
Engine Make
Engine Model
NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.
Engine Type/Spec
Engine Code/Serial Number
CE Models: Place the extra copy of the identification tag
in the manual.
A
CE IDENTIFICATION TAG MARKINGS
Part No. xxxxxxx
A. Manufacturer’s Identification Number
B. Manufacturer’s Serial Number
C. Power Rating in Kilowatts
D. Maximum Engine Speed in Rotations per Minute
E. Manufacturer’s Name and Address
F. Year of Manufacture
I
xxxxxxxxxxxxxxx
Serial No. xxxxxxxxxx
B
H
xxx
dB
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxx
kg: xxx
C
E
G. CE Compliance Logo
H. Mass of Unit in Kilograms
kW: x.xx
xxxx max
20xx
D
I. Guaranteed Sound Power in Decibels
F
G
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Features, Controls, & Operation
CONTROL LOCATIONS
IMPORTANT NOTE
Please take a moment and familiarize yourself with the
name, location, and function of these controls so that you
will better understand the safety and operating instruc-
tions provided in this manual.
The information below briefly describes the function of
individual controls. Starting, stopping, and driving
require the combined use of several controls applied in
specific sequences. To learn what combination and
sequence of controls to use for various tasks see the
OPERATION section.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Features & Controls
Speed Selector
Starter
Selects forward speeds 1-6 and reverse speeds 1-2. No
neutral position or gate is required, since the traction
drive design automatically provides "neutral" (no forward
or reverse movement), whenever the Drive Control is
released.
Electric Start: Depressing the starter button activates
the electric starter. The electric start button operates on
120 Volts AC, which is provided by connection to the
extension cord provided. Connect this extension cord
ONLY to a properly grounded 3 prong electrical outlet.
Recoil Starter (All Models): Pulling the recoil handle
cranks the engine.
Traction Control / Free Hand™ Lock
Engages traction drive to wheels when depressed. Also
locks auger control when depressed simultaneously.
Releasing the traction control lever releases the Free
Hand™ auger control lock and stops the drive wheels
and auger.
Fuel
Fuel tank filler cap (see illustration). Note: The fuel shut
off valve is located under the fuel tank or on the front of
the engine. Close the valve when the snowthrower is not
in use. Open the valve before starting. Fill tank to
approximately 1.5 in. (38 mm) below top of neck to allow
for fuel expansion.
Auger Control
Engages the auger/impeller when depressed. Releasing
the control stops the auger/impeller.
Primer Button
When pressed, the primer button provides initial fuel to
help start a cold engine. Normally, pressing the primer
button twice will provide enough fuel to start a cold
engine.
Chute Direction Control
Push the lever forward to unlock the rotator control.
Moving the lever to the left will turn the spout to the left
side and moving the lever to the right will rotate the spout
to the right side. Releasing the lever locks the spout in
position.
Throttle Lever (Optional)
Controls engine speed. Move toward the hare icon for faster
engine speed, move toward the turtle icon for slower engine
speed. Move the throttle all the way to STOP the engine. Set
the throttle to FAST (hare icon) for operation.
Remote Deflector Control
Chute Deflector: Locks chute deflector in desired posi-
tion. Tilting the chute deflector UP provides a higher
stream and greater distance, while tilting the deflector
DOWN provides a lower stream and less distance.
Engine Key
The engine key prevents the engine from being started.
The key must be fully inserted into the key slot for the
unit to start. The key can also used to stop the engine by
pulling the key out of the key slot.
Easy Turn™ Control
Easy Turn Control: Engaging the Easy Turn™ lever
releases the left wheel to allow easy turning in tight
areas. Releasing the control automatically engages both
drive wheels for full traction.
Choke Knob
The choke knob adjusts the air/fuel mixture, and is used
to help start a cold engine by providing a richer mixture.
Once the engine is warm and running smoothly, the
choke knob should be set to the off position to provide a
normal air/fuel mix.
Traction Lock Pins: (1100 Series Only) The right trac-
tion wheel can be completely released using the locking
pin (see Figure 9). This allows the unit to be easily
moved with the engine off.
Stop Switch (Optional)
Headlight (Select Models, Not Pictured)
Turn the the switch to the ON position to operate the
engine. Turn the switch to the OFF position to stop the
engine.
The headlight is on at all times when the engine is run-
ning.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
GENERAL OPERATION
WARNING
This unit is a “two-stage” snowthrower.
CHECKS BEFORE EACH START-UP
The first stage is the auger, which feeds the snow
back into the impeller housing. The second stage
is the impeller, which throws the snow out the
discharge chute. If bodily contact is made with
the auger or impeller when they are rotating,
severe personal injury will occur.
1. Make sure all safety guards are in place and all nuts,
bolts and clips are secure.
2. Check to make sure that the clean-out is attached to
the auger housing. Do not operate the machine with-
out the clean-out tool properly stored on the auger
housing.
To avoid injury, keep others and yourself away
from the auger and the discharge chute whenever
the engine is running. Read and follow all of the
safety rules and warnings in this manual.
3. Check the engine oil level. See your engine owner’s
manual for procedure and specifications.
4. Check to make sure spark plug wire is attached and
spark plug is tightened securely. If necessary, torque
spark plug to 15 ft. lbs.
DANGER
5. Check the fuel supply. Fill the tank no closer than 1/4
to 1/2 inch of top of tank to provide space for expan-
sion. See your engine owner’s manual for fuel recom-
mendations.
Do not clean out discharge chute with hands.
Contact with moving parts inside chute will
cause serious injury. Use clean out tool provided
with machine. Use the following procedure to
remove objects or clear the chute:
6. Check the scraper bar to make sure it is set at the
desired height. Adjust the skid shoes if necessary.
1. Stop the engine. Remove the key.
2. Wait 10 seconds to be sure the auger/impeller
blades have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
7. Check the drive control (B, Figure 5), and auger con-
trol (C) for proper operation. If adjustment is required,
see the service section for procedures.
8. Check the chute direction control (D, Figure 5) for
proper operation. The discharge chute should rotate
freely in both directions. See the service section for
adjustment procedures and troubleshooting.
WARNING
9. Check the chute deflector (E, Figure 5) for proper
operation. The deflector should pivot freely up and
down.
For your safety, operation on slopes should be in
an up and down direction only. If it becomes nec-
essary to move across the face of a slope, use
caution and do not blow snow. Be very careful
when changing direction on a slope.
10. Position the chute at the desired starting direction
and set the deflector at the desired angle.
11. Check the speed selector (A, Figure 5) for smooth
operation. The control must move freely into each
speed position gate and remain in position when
released. If the speed selector does not move freely
into all forward and reverse speed positions, contact
your local authorized dealer for assistance.
Proper winter footwear is recommended for the
operator to help prevent slipping. Never attempt
to clean snow from excessively steep slopes. The
maximum slope for any operation is 17.7% (10º).
WARNING
Gasoline is highly flammable and must be han-
dled with care. Never fill the tank when the engine
is hot or running. Always move outdoors to fill
the tank. Keep snowthrower and gasoline away
from open flame or spark.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
STARTING CONTROLS
See Figure 1 for the following instructions.
Electric Start
G
D
A. Electric Start Button - The Electric Start Button
(A) activates an electric starter mounted to the
engine, eliminating the need to pull the starter han-
dle. The Electric Start Button operates on 120 Volts
AC, which is provided by connection to the extension
cord provided with units equipped with this feature.
Connect this extension cord ONLY to a properly
grounded 3 prong electrical outlet.
F
A
B
Manual Start
E
B. Fuel Valve - (Select Models) The fuel valve (B) is
located under the fuel tank. It is used to turn the fuel
supply off for out-of-season storage.
C. Starter Handle - The starter handle (C) connects to a
starter cord to manually start the engine. Pulling
starter handle rapidly spins the engine crankshaft,
cycles the engine, and generates the spark neces-
sary for starting the engine.
Snow Series Max
C
F
G
B
D. Primer Button - When pressed, the primer button
(D) provides initial fuel to help start a cold engine.
Normally, pressing the primer button twice will pro-
vide enough fuel to start a cold engine.
A
E. Throttle Lever - (Optional) The throttle lever (E) con-
trols the engine speed. For best overall performance,
the throttle lever should be set to the FAST position.
Use the SLOW position only for warming the engine,
or to help prevent snow/ice freeze-up when shutting
the unit down for the day.
F. Engine Key - The engine key (F) prevents the
engine from being started by unauthorized individu-
als. The key must be fully inserted into the key slot
for the unit to start. The key is also used to stop the
engine by pulling the key out of the key slot.
D
C
H
Snow Series
G. Choke Knob - The choke knob (G) adjusts the
air/fuel mixture, and is used to help start a cold
engine by providing a richer mixture. Once the engine
is warm and running smoothly, the choke knob
should be set to the off position to provide a normal
air/fuel mix.
Figure 1. Engine Controls
A. Electric Start Button
B. Fuel Valve (Select Models)
C. Starter Handle
D. Primer Button
E Throttle Lever (Optional)
F. Engine Key
H. Stop Switch - (Optional) Switch to the ON position
to operate the engine. Switch to the OFF position to
stop the engine.
G. Choke Knob
H. Stop Switch (Optional)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
STARTING THE ENGINE
CAUTION
WARNING
This engine was shipped from Briggs & Stratton
without oil. Before you start the engine, make
sure you add oil according to the instructions in
the Engine Owner’s Manual. If you start the
engine without oil, it will be damaged beyond
repair and will not be covered under warranty.
Rapid retraction of starter cord (kickback) will pull
hand and arm toward engine faster than you can
let go. Broken bones, fractures, bruises or
sprains could result. When starting engine, pull
the starter cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
1. Check the oil level. See “How To Check/Add Oil”
section in Engine Owner’s Manual.
2. Make sure equipment drive controls, if equipped, are
disengaged. See the equipment manual for location
and operation of these controls.
WARNING
Gasoline and its vapors are extremely flammable
and explosive. Fire or explosion can cause severe
burns or death. When starting the engine, ensure
that spark plug, muffler, fuel cap and air cleaner
are in place and secured. Do not crank engine
with spark plug removed. If engine floods, set
choke (if equipped) to open/run position.
3. Push the stop switch (A, Figure 2), if equipped, to
the ON position.
Or move the throttle control lever (A, Figure 3), if
equipped, to the FAST position. Operate the engine
with the throttle control lever in the FAST position.
WARNING
A
Engines give off carbon monoxide, an odorless,
colorless, poison gas. Breathing carbon monox-
ide can cause nausea, fainting or death. When
starting the engine, start and run engine out-
doors. Do not start or run engine in enclosed
area, even if doors or windows are open.
Figure 2. Engine Start/Stop
A. Stop Switch
4. Turn the fuel shut-off valve (B, Figure 3), if equipped,
to the ON position.
WARNING
Unintentional sparking can result in fire or elec-
tric shock.
5. Push in the safety key (C).
6. Turn the choke control knob (D) to the choke posi-
tion.
Unintentional start-up can result in entanglement,
traumatic amputation, or laceration.
NOTE: Do not use the choke to start a warm engine.
7. Push the primer button (E) two times.
• Use a 3-wire extension cord.
• First attach extension cord to electric starter
connector and then into a wall receptacle. If
additional extension cord is required, use a 3-
wire.
NOTE: Do not use the primer to start a warm engine.
8. Rewind Start: Firmly hold the starter cord handle
(F). Pull the starter cord slowly until resistance is felt,
then pull rapidly.
• If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid a hazard.
NOTE: If the engine does not start after three
attempts, see the “Troubleshooting” section in the
Engine Owner’s Manual.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
NOTE: If the engine does not start after three
attempts, see the “Troubleshooting” section in the
Engine Owner’s Manual.
D
E
11. Allow the engine to warm up for several minutes.
Then, slowly move the choke control knob to the run
position.
B
A
C
C
A
B
F
Figure 3. Engine Start/Stop
A. Throttle Control Lever
B. Fuel Shut-Off Valve
C. Safety Key
D. Choke Control Knob
E. Primer Button
F. Starter Cord Handle
Figure 4. Engine Start - Electric
A. Power Cord Receptacle
B. Push Button
9. Electric Start: First connect the extension cord to
the power cord receptacle (A, Figure 4) and then into
a wall receptacle. If an additional extension cord is
required, make sure it is a 3-wire.
C. Starter Cord Handle
STOPPING THE ENGINE
WARNING
WARNING
Gasoline and its vapors are extremely flammable
and explosive.Fire or explosion can cause severe
burns or death. Do not choke the carburetor to
stop the engine.
If the extension cord is damaged, it must be
replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a
hazard.
1. Move the stop switch (A, Figure 2), if equipped, to
the STOP position.
CAUTION
To extend the life of the starter, use short starting
cycles (five seconds maximum). Wait one minute
between starting cycles.
Or move the throttle control lever (A, Figure 3), if
equipped, to SLOW and then to the STOP position.
2. Remove the safety key (C). Keep the safety key out
of reach of children.
10. Electric Start: Depress the push button (B). After
you start the engine, first disconnect the exten-
sion cord from the wall receptacle and then from the
power cord receptacle (A).
3. After the engine stops, turn the fuel shut-off valve (B)
to the CLOSED position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
OPERATING THE SNOWTHROWER
1. Rotate the discharge chute to the desired direction.
WARNING
When BOTH levers are depressed, the Free-
Hand™ Control is activated. This allows Auger
Engage Control to be released — YET AUGER
ROTATION WILL CONTINUE — until the Free-
Hand™ Control is released.
2. Set the speed selector to the desired forward speed.
3. Fully press and hold the auger engage control (C,
Figure 5) on the right-hand grip to begin auger rota-
tion. Releasing the auger engage control will disen-
gage the auger —unless the Free-Hand™ Control
has been activated (See Step 5 below).
4. Fully press and hold the traction & Free-Hand™
Control lever (B, Figure 5) on the left-hand grip to
engage the traction drive and begin moving the
snowthrower. To disengage the traction drive, com-
pletely release the lever.
A
D
5. When BOTH levers are depressed, the Free-Hand™
Control is activated. This allows Auger Engage
Control to be released — YET AUGER ROTATION
WILL CONTINUE — until the Free-Hand™ Control
is released.
B
C
6. Select forward or reverse speeds as needed using
the Speed Selector (A, Figure 5). Release both con-
trol levers before changing drive speeds.
F
E
Figure 5. Controls (From Operator’s Position)
A. Speed Selector
B. Traction & Free-Hand™ Control
C. Auger Engage Control
CLEARING A CLOGGED DISCHARGE
CHUTE
IMPORTANT NOTE
Hand contact with the rotating auger/impeller
inside the discharge chute is the most common
cause of injury associated with snowthrowers.
DO NOT use your hand to clean out the discharge
chute.
D. Chute Rotator Control
E. Remote Deflector Control
F. Easy Turn Lever
To clear the chute:
1. Stop the engine. Remove the key.
2. Wait 10 seconds to be sure the auger/impeller blades
have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
GROUND SPEED SELECTOR
Use the speed selector (A, Figure 5) to control the drive
speed of the snowthrower. There are six forward speeds
and two reverse speeds.
Use the lower speeds to blow deep or wet snow. Use the
higher speeds to blow light snow or to drive the snow-
thrower without blowing snow.
To change speeds, release the auger control lever (B,
Figure 5), then move the speed selector to the desired
setting. Fully depress the control levers to resume.
A
ENGINE SPEED
Always run the snowthrower at full throttle.
B
DEFLECTOR
The distance of the discharged snow is mainly controlled
by the position of the deflector. (Engine speed also
affects distance of discharge.) The more the deflector is
tilted UP, the farther snow will be thrown.
1. Push the remote deflector control (E, Figure 5) to the
left to UNLOCK the control. Sliding the control for-
ward will put the deflector to the maximum throwing
position (A, Figure 6). Sliding the control backwards
to decrease the throwing distance.
Figure 6. Remote Deflector Control
A. Maximum Throwing Position
B. Spring
2. Release the control to LOCK in place when the
desired angle has been chosen.
SCRAPER BAR & SKID SHOES
On smooth surfaces such as concrete or asphalt, the
scraper bar (A, Figure 7) should scrape the surface. On
surfaces such as gravel, the scraper bar should be high
enough so that it will not pick up gravel or debris.
The height of the scraper bar (A) is controlled by raising
or lowering the skid shoes (B).
A
1. To raise the scraper bar height, rest the scraper bar
(A) on a strip of wood equal in thickness to the desired
height.
C
2. Make sure the scraper bar is parallel to the ground
surface.
B
3. Loosen the skid shoe nuts (C) and let the skid shoes
(B) drop to the surface.
Figure 7. Skid Shoe Adjustment
A. Scraper Bar
4. Tighten the nuts (C), making sure the skid shoes are
adjusted equally and are parallel to the surface.
5. To lower the height of the scraper bar, raise the skid
shoes. Or adjust scraper bar by loosening the attach-
ment bolts and sliding scraper bar down.
6. If the scraper bar becomes worn, it can be replaced
by removing the hardware attaching it to the
snowthrower.
B. Skid Shoe
C. Nuts
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
FULL TRACTION
EASY TURN™ TRACTION
Easy Turn™
Lever
Released
Easy Turn™
Lever
Engaged
Left Wheel Freewheels,
Right Wheel Drives
Both Wheels Drive
Figure 8. Easy Turn Control
B
A
EASY TURN™ FREEWHEELING AND
TRACTION DRIVE LOCK
While Clearing Snow:
For easy turning when using the snowthrower, squeeze
the Easy Turn™ lever (Figure 8). Engaging the Easy
Turn™ lever releases the left traction wheel but allows
the right wheel to continue driving (Figure 8). Releasing
the Easy Turn™ lever automatically engages both drive
wheels for full traction.
Figure 9. Traction Drive Lock
A. Pin in Outer Hole (Freewheel)
B. Pin in Inner Hole (Drive)
NOTE: The Easy Turn™ lever will be more difficult to
activate under a heavy load. Activate the lever before
beginning a turn.
2. To DISENGAGE the traction drive lock, insert the
Traction Lock Pin (A, Figure 9) through the outer hole
in the right axle. The unit can now be pushed with
minimal resistance.
When Pushing the Snowthrower:
(Units without Easy Turn)
3. To ENGAGE the traction drive lock, align the hole in
the hub with the inner hole in the axle, and install the
Traction Lock Pin (B).
For easy turning when pushing the snowthrower, disen-
gage the right wheel using the traction lock pin (See
Figure 9).
NOTE: Be sure both wheels are locked (locking pin in
inner hole) when clearing snow.
1. Turn the unit off, remove the engine key, and discon-
nect the spark plug wire.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
AFTER EACH USE
WARNING
Normal use of the snowthrower may result in a build-up
of packed snow in and around the starter cord housing
and around engine controls. Heat from the engine will
usually prevent the snow from freezing solid while the
unit is running, but after the engine is shut down, some
snow may continue melting from engine heat, and later
freeze around some moving parts as the unit cools.
Never store the unit, with gasoline in engine or
fuel tank, in a heated shelter or in enclosed, poor-
ly ventilated enclosures. Gasoline fumes may
reach an open flame, spark or pilot light (such as
a furnace, water heater, clothes dryer, etc.) and
cause an explosion.
Handle gasoline carefully. It is highly flammable
and careless use could result in serious fire dam-
age to your person or property.
After each period of use, follow these steps to prevent
freeze-up caused by ice formation in and around the
engine controls and external parts.
Drain fuel into an approved container outdoors
away from open flame or sparks.
1. Before shutting off the engine, pull the starter rope
out 2 - 3 times, and allow it to rewind slowly. This will
help clear packed snow from the starter cord area.
Allow the engine to run for several minutes.
2. Stop the engine by moving the throttle lever (See
Figure 1) down, turn the stop switch to the off position
or by pulling out the engine key.
STORAGE
3. Brush snow and ice from the snowthrower. Be sure to
clear engine and snowthrower controls, discharge
chute, and chute rod gears, clutch cable areas, and
anywhere else snow has accumulated.
WARNING
Never store the unit (with fuel) in an enclosed,
poorly ventilated structure. Fuel vapors can trav-
el to an ignition source (such as a furnace, water
heater, etc.) and cause an explosion.
4. Always remove the engine key and store in a safe
place to prevent unauthorized use.
Fuel vapor is also toxic to humans and animals.
WARNING
Never store the unit (with fuel) in an enclosed,
poorly ventilated structure. Fuel vapors can trav-
el to an ignition source (such as a furnace, water
heater, etc.) and cause an explosion.
Before you store your unit for the off-season, read the
Maintenance and Storage instructions in the Safety
Rules section, then perform the following steps:
• Disengage the PTO, set the parking brake, and
remove the key.
Fuel vapor is also toxic to humans and animals.
• Perform engine maintenance and storage measures
listed in the engine owner’s manual. This includes
draining the fuel system, or adding stabilizer to the
fuel (do not store a fueled unit in an enclosed struc-
ture - see Warning).
5. If the snowthrower is kept in a cold shelter, fill the fuel
tank to prevent condensation. Do not store near
sparks or flame.
Before starting the unit after it has been stored:
NOTE: The Engine Owner’s Manual contains further
information on preventing ice formation and freeze-up.
• Check all fluid levels. Check all maintenance items.
• Perform all recommended checks and procedures
found in the engine owner’s manual.
WARNING
• Allow the engine to warm up for several minutes
before use.
When BOTH levers are depressed, the Free-
Hand™ Control is activated. This allows Auger
Engage Control to be released — YET AUGER
ROTATION WILL CONTINUE — until the Free-
Hand™ Control is released.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Regular Maintenance
MAINTENANCE SCHEDULE
Maintenance Required
Frequency
Notes
Check / Lubricate Free-Hand Linkage.
Lubricate snowthrower.
10 Hours
10W Oil
10W Oil and Grease
20 psi (1,38 bar)
See Engine Manual
See Engine Manual
See Page 28
10 Hours
Monthly
Check tire pressure.
+
Change engine oil.*
50 Hours
Yearly
+
Clean or replace spark plug.
Check drive linkage/belt tension.
Lubricate Axle Shafts.
4-6 Hours
Yearly
Lithium Grease
Benalene Grease
Lithium Grease
Check auger gear case lubrication.**
Lubricate Auger Shaft.***
25 Hours
10 Hours
* Change original oil after two hours of operation.
** Check oil level each fall and spring.
+ See your engine Owner’s Manual.
***Lubricate each fall and spring.
CHECKING TIRE PRESSURE
The air pressure in each tire (Figure 10) should be equal
for both tires for best performance. Be sure to keep caps
on valves to prevent entry of debris into the valve stem
when tires are filled.
Size
15 x 5.0-6
PSI
20
bar
1,38
,96
Figure 10. Checking Tire Pressure
16 x 4.8-8
14
AUGER GEAR CASE LUBRICATION
1. Place the snowthrower on a level surface.
2. Remove the pipe plug (A, Figure 11).
3. Check the lubricant level. It should be level with the
lower edge of the plug opening. If not, add Benalene
grease.
A
4. Re-install pipe plug, and tighten securely.
Figure 11. Auger Lubrication
A. Pipe Plug
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Regular Maintenance
LUBRICATION
IMPORTANT NOTE
It is very important that grease fittings on the
auger shaft are lubricated regularly. If auger rusts
to shaft, damage to worm gear may occur if shear
pins do not break.
A
To prevent wheels rusting to axles, it is also nec-
essary to remove the wheels and grease the axles
regularly.
Remove wheels and grease axles once each year.
Apply 5W-30 synthetic motor oil to the friction disk drive
hex shaft (A, Figure 13).
Figure 13. Drive Lubrication
A. Hex Shaft (Behind Rod With Spring)
Apply medium weight (10W) oil to points shown (See
Figures 12-15).
Generally, all moving metal parts should be oiled where
contact is made with other parts. Keep oil and grease off
belts, pulley grooves, drive disc, and friction disc.
LUBRICATION NOTES:
Grease locations indicated by grease gun symbol.
Use grease fittings when present. Disassemble
parts to apply grease to moving parts when grease
fittings are not installed.
Oil locations indicated by oil can symbol. Do not
allow oil to drip onto traction drive or friction disc.
Do not lubricate remote deflector control.
Figure 14. Lubricate Axles and Control Levers
Figure 15. Deflector Hinge
Figure 12. Lubricate Spout Rotator
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Regular Maintenance
CHECK / LUBRICATE FREE-HAND
LINKAGE
Check the function of the Free-Hand controls. The con-
trols should function as described in the CONTROLS
section. It is critical for the safe operation of the unit
that the controls disengage when released.
Lubricate as shown in Figure 16.
IMPORTANT NOTE
If the controls do not function properly, lubricate them. If
lubrication does not rectify the problem, see your dealer.
Under no circumstances should the unit be used if the
controls are not functioning properly.
Figure 16. Lubricate Free-Hand Control
IMPORTANT NOTE
It is very important that grease fittings on the auger shaft
are lubricated regularly. If auger rusts to shaft, damage to
worm gear may occur if shear pins do not break.
B
LUBRICATE AUGER SHAFT
ASSEMBLY
A
C
B
1. Remove cotter pin (C, Figure 17) and shear pin (B).
2. Use a grease gun and squirt several shots of grease
into grease fitting (A).
C
3. Rotate auger assembly (D) several times to distribute
the grease evenly. Repeat Step 2.
A
D
4. Reinstall shear pin (B) and cotter pin (C).
5. Repeat procedure for other side.
D
Figure 17. Lubricate Auger Shaft Assembly
A. Grease Fittings
B. Shear Pins
C. Cotter Pins
D. Auger Assembly
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
TROUBLESHOOTING
This section provides troubleshooting and service
instructions. Locate the problem and check the possible
cause/remedy in the order listed.
WARNING
Before performing any adjustment or service to
snowthrower, stop the engine and wait for mov-
ing parts to stop. Remove the key. To prevent
accidental starting, disconnect the spark plug
wire and fasten away from the plug.
Also, refer to the Engine Owner’s Manual for additional
information.
For problems not covered here, contact your local deal-
er.
Problem
Possible Cause
Remedy
Engine fails to start.
Key is OFF.
Push key in to the ON position.
Failure to prime cold engine
Fuel valve is in CLOSED position.
Out of fuel.
Press primer button twice and
restart.
Turn valve to OPEN position.
Fill fuel tank.
Choke OFF - cold engine.
Engine flooded.
Turn choke to ON, set throttle to
FAST.
Turn choke to OFF; try starting.
No spark.
Check gap. Gap plug, clean elec-
trode, or replace plug as necessary.
Water in fuel, or old fuel.
Drain tank. (Dispose of fuel at an
authorized hazardous waste facility.)
Fill with fresh fuel.
Engine starts hard or runs poorly. Fuel mixture too rich.
Carburetor adjusted incorrectly.
Move choke to OFF position.
See your dealer for adjustments.
Clean and gap, or replace.
Clear vent.
Spark plug faulty, fouled, or gapped
improperly.
Fuel cap vent is blocked.
Scraper bar does not clean hard
surface.
Skid shoes improperly adjusted.
Skid shoes improperly adjusted.
Auger control not engaged.
Foreign matter blocking auger.
RAISE skid shoes (this lowers the
scraper bar).
LOWER skid shoes (this raises the
scraper bar.)
Auger does not rotate.
Engage auger control.
STOP engine and REMOVE the
key. DISCONNECT the spark plug
wire. Clear auger using clean-out
tool. See warning in SAFETY
RULES.
Auger drive clutch cable slack.
Auger drive belt slipping.
Broken belt.
Tighten to remove slack. See auger
clutch cable adjustment.
Check auger drive belt adjustment.
Replace belt.
Shear pin broken.
Replace shear pin.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Possible Cause
Remedy
Auger rotates, but snow is not-
thrown far enough.
Chute deflector too low.
Adjust deflector as necessary.
Engine speed too slow.
Ground speed too fast.
Set speed to full throttle.
Use slower speed selector setting.
Snowthrower discharge chute
clogged.
STOP engine and REMOVE the key.
DISCONNECT the spark plug wire.
Clear auger using clean-out tool. See
warning in SAFETY RULES.
Auger belt loose or worn.
Tires slipping.
Check auger drive belt adjustment
Check tire pressure and tread.
Poor traction.
Auger does not stop when
auger lever is released.
Free-Hand™ control is ACTIVE.
Release both auger engage control
AND Free-Hand™ control to stop
auger.
Auger clutch rod too tight or bent.
Auger drive belt out of adjustment.
Loosen or straighten clutch rod.
Adjust auger belt.
Auger belt guide out of adjust-
ment.
Adjust auger belt guide.
Snowthrower does not stop
when drive lever is released.
Traction drive clutch rod bent or
too tight.
Loosen rod to remove slack or replace.
See adjustment procedure.
Traction drive clutch rod loose.
Tighten to remove slack. See adjust-
ment procedure.
Drive belt loose, broken, or
stretched.
Replace drive belt.
Drive roller chain damaged.
Replace chain.
Traction lock pins in free-
Wheeling position (OUTER hole).
Change traction lock pins to INNER
hole to engage traction drive.
Friction disc worn.
Replace disc (see your dealer).
Oil or grease as required.
Discharge control is difficult to
operate.
Gearing needs lubrication
Worm gear not adjusted properly.
Adjust worm gear. See adjustment pro-
cedure.
Control rod gears misaligned.
Adjust gear bracket. See adjustment
procedure.
Snowthrower veers to one
side.
Tire pressure not equal.
Check tire pressure.
One wheel is set in free-wheeling
mode. (Traction Lock Pin is in the
OUTER hole).
Make certain the left traction lock pin is
in the INNER holes (to engage traction
drive).
Excessive vibration.
Loose parts or damaged auger.
STOP engine and REMOVE the key.
DISCONNECT the spark plug wire.
Tighten all hardware. Replace auger if
necessary. If vibration continues, see
your dealer.
Drive fails to move
Traction drive out of adjustment.
Hex shaft needs lubrication.
Readjust drive, or shift speed selector
setting up one speed faster.
snowthrower at slow speeds.
Speed selector difficult to
move or frozen in place.
Lubricate hex shaft with 5W-50 syn-
thetic motor oil (see Maintenance).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
AUGER DRIVE ADJUSTMENT
C
B
WARNING
Do not over-tighten, as this may lift the lever and
cause auger drive to be engaged without depress-
ing the Auger Control.
A
1. Check that the auger cable (A, Figure 18) is on top of
cable button (B) as show in Figure 18.
2. With the drive lever released, the hook (B, Figure 19)
should barely touch the lever (C) without raising it.
There can be a maximum 1/32” clearance as shown.
Figure 18. Auger Cable Button
A. Auger Drive Cable
B. Auger Cable Button
C. Lever
3. To adjust, loosen nut (D) by holding the adjusting
flats (A) and turning nut (D). Turn adjustment flats
and hold screw. The adjustment screw is a phillips
screw and the head can be held or turned by insert-
ing a screwdriver through the spring (F).
4. Hold adjusting flats (A) and tighten nut (D).
5. Start unit and check auger. Auger must not be
engaged unless auger control is depressed.
A
D
6. With engine running, fully depress auger control, the
auger should engage and run normally.
7. Release auger control. Auger must stop within 5
E
seconds.
8. If auger does not operate properly, stop engine and
recheck drive linkage adjustments.
9. If auger linkage is properly adjusted, auger drive belt
tension may require adjustment. See “Belt
F
Adjustment” in this section of the manual.
1/32” (.080cm)
TRACTION DRIVE CABLE
ADJUSTMENT
Initial Adjustment
C
B
1. With the drive lever released there should be no
slack in cable when moved slightly from side to side.
Figure 19. Auger Drive Adjustment
A. Adjusting Flats
B. Spring Hook
C. Lever
D. Nut
E. Adjustment Screw
F. Spring
WARNING
Do not over-tighten, as this may cause traction
drive to engage without depressing the traction
drive control (arm must remain in down position).
2. To adjust tension on the cable slide the cable boot
(A, Figure 20) off the cable adjustment bracket (D).
3. Remove the “Z” hook (C) from the cable adjustment
bracket (D) to a different adjustment hole. The cable
should have no slack. The cable should have no ten-
sion or load.
Verify that the cables are not over-tightened: With
speed selector in position 1 and traction drive
control fully released, push snowthrower forward.
The unit should move forward freely.
NOTE: If the cable is too slack the unit will not drive. If
the cable is too tight the drive will be engaged without
pushing the handles down.
If unit does not move forward freely, the cable has
been over-tightened. To remedy, loosen tension
on clutch cable slightly, and recheck.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
A
A
B
B
B
C
D
4-5/16”
C
(10.95cm)
Figure 20. Traction Drive Cable Adjustment
A. Cable Boot
B. Traction Drive Cable
C. “Z” Hook
Figure 21. Friction Disc Measurement
A. Friction Disc
B. Frame
D. Cable Adjustment Bracket
A
4. Slide the cable boot (A) over the cable adjustment
bracket.
E
Run-In Adjustment
B
ALL MODELS
C
1. After 5 hours of use, check for proper adjustment.
Readjust clutch cable if necessary by increasing ten-
sion on cable. A small amount of arm movement is
permissible if unit passes operating checks described
in the Warning above.
D
Figure 22. Speed Selector Linkage
A. Speed Selector Rod
B. Jam Nut
C. Ball Joint
D. Locknut
E. Shift Rod
WARNING
5. Note the position of the friction disc (A, Figure 21).
The correct distance from the right side of the friction
wheel to the outside of the frame is 4-5/16” (10.95
cm). If the friction disc is not in the correct position,
adjust as follows.
Gasoline is highly flammable and must be han-
dled with care. Drain gasoline outdoors. Never
drain the tank when the engine is still hot from
recent operation. Do not allow open flame, smok-
ing or matches in the area. Avoid over-filling and
wipe up any spills.
6. Position the shift speed lever in the lowest forward
speed.
1. Remove the gas from the gas tank.
2. Disconnect the spark plug wire.
7. Loosen the jam nut (B, Figure 22).
8. Remove locknut (D).
3. Stand snowthrower on the front of the auger housing
(C, Figure 28).
9. Move the friction disc (A, Figure 21) to the correct
distance, 4-5/16” (10.95 cm).
2. Loosen the capscrews (A, Figure 28) on each side of
the bottom panel (B).
10. Turn the ball joint (C, Figure 22) until it is aligned with
the mounting hole in the shifter rod (E). When
aligned, attach the ball joint (C) to the shifter rod (E)
and tighten the jam nut (B).
3. Remove the bottom panel (B).
4. Position the shift speed lever in the lowest forward
speed.
11. Check that the snowthrower operates in R1. If not
follow procedures 1-11 and readjust as necessary.
12. Install the bottom panel (B, Figure 28) and tighten the
capscrews (A).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
EASY TURN™ CABLE ADJUSTMENT
If the Easy Turn™ cable has stretched, the gears will not
disengage when the control lever is activated. Adjust the
cable using the following procedure.
1. Turn the engine off and disconnect the spark plug
wire.
2. Loosen the jam nut (B, Figure 23).
B
3. Turn the adjustment nut (A) to lengthen or shorten
the cable. The cable should be tightened just until all
slack is removed from the lever, however it must not
engage the Easy Turn™ release without depressing
the control lever.
A
4. Tighten the jam nut.
Figure 23. Cable Adjustment
A. Adjustment Nut
B. Jam Nut
BELT ADJUSTMENT
Auger Drive Belt
If your snowthrower will not discharge snow, check the
control cable adjustment. If it is correct, then check the
condition of the auger drive belt. If it is damaged or
loose, replace it. See “Belt Replacement” in this section
of the manual.
B
1. Disconnect spark plug wire.
2. Remove screw (B, Figure 24) from belt cover (A).
Remove belt cover (A).
3. Loosen nut (D, Figure 23) on auger idler pulley (B)
and move auger idler pulley towards belt about 1/8
inch (3 mm).
B
A
4. Tighten nut (D).
Figure 24. Belt Cover
A. Belt Cover
B. Screws
5. Engage auger drive clutch. Check tension on belt
(opposite idler pulley). Belt should deflect about 1/2
inch (12.5 mm) with moderate pressure see Figure
25). You may have to move the idler pulley more
than once to obtain the correct tension.
A
B
6. Reinstall belt cover (A, Figure 24) securing with
screws (B).
E
7. Whenever belts are adjusted or replaced, the cables
will need to be adjusted. See “Cable Adjustment” in
this section of the manual.
D
1/2” (12.5 mm)
Deflection
8. Attach the spark plug wire.
Traction Drive Belt
C
The traction drive belt has constant spring pressure and
does not require an adjustment. If the traction drive belt
is slipping,replace the belt. See “Belt Replacement” in
this section of the manual.
Figure 25. Auger Belt Deflection
A. Engine Drive Pulley
D. Nut
B. Idler Pulley (Engaged) E. Auger Belt
C. Auger Drive Pulley
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments & Service
SHEAR PIN REPLACEMENT
WARNING
B
Do not go near the discharge chute or auger
when the engine is running. Do not run the engine
with any cover or guard removed.
A
Under most circumstances, if the auger strikes an object
which could cause damage to the unit, the shear pin will
break. (This protects the gear box and other parts from
damage.)
A
B
The shear pins are located on the auger shaft as shown
in Figure 26. To replace the shear pins, tap out the bro-
ken pin with a pin punch, and install a new shear pin and
cotter pin. Do NOT replace shear pins with anything
other than the correct grade replacement shear pin.
(Use of bolts, screws or a harder shear pin will lead to
damaged equipment.)
Figure 26. Shear Pins
A. Shear Pins
B. Cotter Pins
BELT GUIDE ADJUSTMENT
1. Disconnect spark plug wire.
C
B
2. Remove screw (B, Figure 24) from belt cover (A).
Remove belt cover (A).
3. Measure the distance between the belt guide (B,
Figure 27) and the belt (D). The distance should be
1/8 inch (3.18 mm).
A
1/8” (3.18 mm)
D
4. If adjustment is necessary, loosen belt guide cap-
screw (C). Move belt guide (B) to correct position.
Tighten capscrew (C).
6. Reinstall belt cover (A, Figure 24) securing with
screws (B).
7. Reconnect spark plug wire.
Figure 27. Belt Guide
A. Idler Pulley (Engaged)
B. Belt Guide
C. Capscrew
D. Belt
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
BELT REPLACEMENT
Auger Drive Belt
The drive belts are of special construction and must be
replaced with original factory replacement belts available
from your nearest authorized service center. Some
steps require the assistance of a second person. If the
auger drive belt is damaged, the snow thrower will not
discharge snow. Replace the damaged belt as follows.
A
A
C
B
1. Disconnect the spark plug wire.
2. Loosen the capscrews (A, Figure 28) on each side of
the bottom panel (B).
Figure 28. Bottom Cover
A. Capscrews
3. Remove the bottom panel (B).
4. Loosen screw (B, Figure 24) from belt cover (A).
Remove belt cover (A).
B. Bottom Panel
C. Auger Housing
5. Loosen the belt guide (B, Figure 29). Pull the belt
guide away from the auger drive pulley (A).
A
6. Pull the auger idler pulley (K) away from the auger
drive belt (D) and slip the belt off of the idler.
B
F
7. Remove the auger drive belt (D) from the engine pul-
ley. To remove the auger drive belt (D), the auger
drive pulley (C) may have to be partially rotated.
C
L
D
8. Index or point the spout rotator to the center of the
machine so the rotator control is in the center of the
dash panel.
K
E
9. Remove special nut (A, Figure 30) and cover (B).
A
10. Remove hair pin (C) and slide rod forward about 3
inches. Until hex shaft separates from handle con-
trol.
J
G
11. Remove the upper four capscrews (A, Figure 32) that
hold together the auger housing (C) and the frame
(D). Loosen the lower two capscrews (B). The auger
housing (C) and the frame (D) can now be split apart
for removal of the belt.
I
H
12. Remove the old auger drive belt (D, Figure 29) from
the impeller pulley. Replace the auger drive belt with
an original factory replacement belt available from an
authorized service center.
Figure 29. Pulleys and Belts
A. Traction Drive Belt
B. Belt Guide
C. Auger Drive Pulley, Engine
D. Auger Drive Belt
E. Traction Drive Spring
F. Traction Drive Pulley, Engine
G. Traction Drive Pulley
H. Impeller Pulley
13. Install the new auger drive belt (D) onto the impeller
pulley.
NOTE: To assemble the auger housing to the frame,
have someone hold the auger clutch lever in the
ENGAGED position. This will move the idler arm and pul-
ley enough to allow the auger drive pulley to move back
into position.
I. Swing Plate Axle Rod
J. “E”-Ring
K. Auger Idler Pulley
L. Traction Drive Idler Pulley
14. Assemble the auger housing (C, Figure 32) to the
frame with the four upper capscrews (A) that were
removed in Step 11. Tighten the two lower capscrews
(B).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments & Service
A
A
D
B
B
A
A
C
B
B
D
Figure 31. Install Spout Rotator Rod
A. Hex Dash Opening
B. Spout Rotator Rod
Figure 30. Spout Rotator Rod
A. Special Nut
B. Cover
C. Hair Pin
D. Spout Rotator Rod
15. Index or point the spout rotator to the center of the
machine so the rotator control is in the center of the
dash panel.
16. Slide spout rotator rod (B, Figure 31) into hex dash
opening (A).
A
17. Insert hair pin (C, Figure 30) into spout rotator rod
(D).
18. Install cover (B) and secure with special nut (A).
19. Install the auger drive belt (D, Figure 29) onto the
impeller pulley (H).
B
20. Slip the auger drive belt (D) under the idler pulley (K).
D
C
21. Adjust the auger drive belt. See “How To Adjust The
Auger Drive Belt” in the Service section.
Figure 32. Frame and Axle Housing
A. Upper Capscrews
B. Lower Capscrews
C. Auger Housing
22. Adjust the belt guide. See “How To Adjust The Belt
Guide” in the Service section.
23. Install the belt cover (A, Figure 24). Tighten screws
(B).
D. Frame
24. Check the adjustment of the cables. See “How To
Check And Adjust The Cables” in the Adjustment
section.
25. Install the bottom panel (B, Figure 28).
26. Tighten the capscrews (A) on each side of the bottom
panel (B).
27. Connect the spark plug wire.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Traction Drive Belt
If the snow thrower will not move forward, check the trac-
tion drive belt for wear or damage. If the traction drive
belt is worn or damaged, replace the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See “How To Remove
The Auger Drive Belt” in the Service section.
3. Remove the e-ring (J, Figure 29) from one end of the
swing plate axle rod (I).
4. Remove the swing plate axle rod (I) to allow the
swing plate (A, Figure 33) to pivot forward.
5. Remove the traction drive spring (E, Figure 29).
A
6. Remove the old traction drive belt (A) from the trac-
tion drive pulley (G) and from the traction drive pulley
(F). Replace the traction drive belt (A) with an origi-
nal factory replacement belt available from an autho-
rized dealer.
B
Figure 33. Traction Belt Change
A. Swing Plate
7. Install the new traction drive belt (A) onto the traction
drive pulley (G) and onto traction drive pulley (F).
B. Alignment Tabs
8. Make sure the traction drive idler pulley (L) is proper-
ly aligned with the traction drive belt (A).
9. Attach the traction drive spring (E).
10. Install the swing plate axle rod (I) and secure with the
e-ring (J) removed earlier.
11. The bottom of the swing plate (A, Figure 33) must be
positioned between the alignment tabs (B). Make
sure the swing plate is properly secured.
NOTE: If the drive will not engage after the traction drive
belt has been replaced, then check to make sure that the
swing plate is positioned between the alignment tabs.
12. Install and adjust the auger drive belt. See “Belt
Replacement” in this section of the manual.
13. Adjust the belt guide. See “Belt Adjustment” in this
section of the manual.
14. Install the bottom panel (B, Figure 28).
15. Tighten the capscrews (A) on each side of the bottom
panel (B).
16. Reinstall belt cover (A, Figure 24) and secure with
screws (B).
17. Check the adjustment of the cables. See “Cable
Adjustment” in this section of the manual.
18. Connect the spark plug wire.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been
obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM;
horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among
other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on
which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas
engine will not develop the rated gross power when used in a given piece of power equipment (actual "on-site" or net
power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust,
charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this Series engine.
ENGINE:
CHASSIS:
- 1226, 1428,
Wheels
Tire Size: 15 x 5
Inflation Pressure: 20 psi (1,37 bar)
Tire Size: 16 x 4.8
Inflation Pressure: 14 psi (,96 bar)
200 Degrees
12 in. (30 cm) 4 Blade Ribbon Flighted Steel
1100 Series Briggs & Stratton
Make
Model
Briggs & Stratton
- 1530, 1632,
Snow Series, M15H
11.00 ft-lbs (14.9 Nm) @ 3060 rpm
15.2 cu. in (249 cc)
19 oz. (,56 l)
Gross Torque*
Displacement
Oil Capacity
Spout Rotation
Impeller
Auger Opening Height 21 in. (53 cm)
Drive System
Friction Disc, 6 Forward Speeds, 2 Reverse
1350 Series Briggs & Stratton
Make
Briggs & Stratton
DIMENSIONS:
Model
Snow Series Max, M20H
13.50 ft-lbs (18.3 Nm) @ 3060 rpm
18.6 cu. in (305 cc)
Effective Clearing Width
Gross Torque*
Displacement
Oil Capacity
- 1226
- 1428
- 1530
- 1632
26 in. (66 cm)
28 in. (71 cm)
30 in. (76 cm)
32 in. (81 cm)
28 oz. (,84 l)
1450 Series Briggs & Stratton
Length
- 1226
- 1428
- 1530
- 1632
Make
Briggs & Stratton
57.5 in. (146 cm)
57.5 in. (146 cm)
57.5 in. (146 cm)
57.5 in. (146 cm)
Model
Snow Series Max, M20H
14.50 ft-lbs (19.7 Nm) @ 3060 rpm
18.6 cu. in (305 cc)
Gross Torque*
Displacement
Oil Capacity
28 oz. (,84 l)
Height
- 1226
- 1428
- 1530
- 1632
1550 Series Briggs & Stratton
44.1 in. (112 cm)
44.1 in. (112 cm)
45 in. (114 cm)
45 in. (114 cm)
Make
Briggs & Stratton
Model
Snow Series Max, M21H
15.50 ft-lbs (21.0 Nm) @ 3060 rpm
20.87 cu. in (342 cc)
28 oz. (,84 l)
Gross Torque*
Displacement
Oil Capacity
Weight
- 1226
- 1428
- 1530
- 1632
248 lbs (112 kg)
255 lbs (116 kg)
255 lbs (116 kg)
260 lbs (118 kg)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts & Accessories
REPLACEMENT PARTS
TECHNICAL MANUALS
Replacement parts are available from your authorized
Additional copies of this manual are available, as well as
dealer. Always use genuine Simplicity / Snapper Service fully illustrated parts lists. These manuals show all of the
Parts.
product’s components in exploded views (3D illustrations
which show the relationship of parts and how they go
together) as well as part numbers and quantities used.
Important assembly notes and torque values are also
included.
MAINTENANCE ITEMS
Many convenient and helpful service and maintenance
items are available from you authorized dealer. Some of
these items include:
For applicable manuals currently available for your
model, contact our Customer Publications Department at
+1-877-249-6647. Have the information listed in the box
below available when phoning in your request.
Technical manuals can be downloaded from:
Engine Oil
Tire Sealant
Degrimer/Degreaser
Gas Stabilizer
Touch-Up Paint
Grease Gun Kit
8 oz. Grease Tube
Model:
Mfg. No.:
Your Name:
Address:
City, State, Zip:
Visa/Mastercard No.:
Card Expiration Date:
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
PRODUCTS
535 Macon Street
McDonough, GA 30253
© Copyright 2007, BRIGGS & STRATTON.
All Rights Reserved. Printed in USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|