Singer Sewing Machine FW75 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN PARTS

7 8 9 10

11 12 13

01 02 03 04 05 06 07 08 09 10 11

21 22

12 13 14 15 16 17 18 19 20

23 24 25 26 27 28 29 30 31 32

34 35 36 37 38 39 40 41 42 43

45 46 47 48 49 50 51 52 53 54

56 57 58 59 60 61 62 63 64 65

1.Face Plate

9.Thread Tension Regulator

10.Spool pin

2.Reverse Stitch Button

3.Slow Button

11.Bobbin winder Shaft

12.Bobbin Winder Stop

13.Hand Wheel

4.Start/Stop Button

5.Speed Control Lever

14.Stitch Width Button

15.Stitch Length Button

16.Pattern Selector Button

17.Thread Cutter

6.Extension Table (Accessory Case)

7.Bobbin Winder Tension disc

8.Needle Up/Down Button

-2-

Download from Www.Somanuals.com. All Manuals Search And Download.

18.Carrying Handle

19.Thread guide for upper threading

20.Power switch

21.Air vent

22.Foot control plug

23.Plug socket

24.Power cord

25.Foot control

26.Lower thread guide

27.Needle threader lever

28.Needle threader

29.Buttonhole lever

30.Presser foot thumb screw

31.Needle plate

32.Bobbin cover

33.Bobbin cover release lever

34.Presser foot holder

35.Presser foot

36.Needle thread guide

37.Needle clamp screw

38.Presser foot lever

39.Drop feed lever

40.LED light

-3-

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

Some accessories are provided in the accessory case.

1.Needle set

2.Bobbins

3.Spool pin cap (large)

4.Spool pin cap (small)

5.Straight stitch foot

6.Needle plate screwdriver

7.Screwdriver

8.Buttonhole opener with brush

9.Oiler

10.Buttonhole Foot

11.Overcasting Foot

12.Zipper Foot

13.Blind hem Foot

14.Satin Foot

15.Rolled hem Foot

16.Gathering Foot

17.Darning & Embroidery Foot

18.General purpose foot(on machine)

19.Extension table

OPENING THE ACCESSORY CASE

To open the accessory case, lift up on the

top left side of the table and pull toward you.

-4-

Download from Www.Somanuals.com. All Manuals Search And Download.

a.REMOVING THE EXTENSION TABLE

Hook your finger to the bottom of extension

table and slid to the left. To attach, insert to

the right.

b.OPENING THE ACCESSORY CASE

Hook your finger to the left side of accessory

case and pull toward you.

DUST COVER

Cover the machine with dust cover when it is

not in use.

This manual will be stored on the holder

provided on the side of the cover.

-5-

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE PRESSER FOOT

The presser foot must be changed according to the stitch you sew, or work you do.

CAUTION:To prevent accidents.

Turn off the power switch before you change the presser foot.

1.Turn the hand wheel toward you until the

needle is at its highest point.

2.Raise the presser foot lifter.

3.Remove the presser foot by pushing the

presser foot release lever toward you.

4.Place desired foot with its pin directly under

the slot in presser foot holder.

5.Lower the presser foot lifter and the presser

foot will snap into place.

REMOVING THE PRESSER FOOT HOLDER

You may need to remove the presser foot holder to use

some presser feet.

To remove, raise the presser foot lifter and loosen the

presser foot thumb screw (A).

To attach, tighten the screw after raising the presser foot

holder.

INSERTING THE NEEDLE

Select a needle of the right type and size for the fabric to be sewn.

CAUTION:To prevent accidents.

Turn off the power before removing the needle.

1.Turn the hand wheel toward you until the

needle is at its highest point.

2.Loosen the needle clamp screw.

3.Remove the needle.

4.Insert new needle into needle clamp with

the flat side to the back and push it up as

far as it will go.

5.Tighten the needle clamp screw.

A.Do not use bent or blunt needles.

Place needle on a flat surface and check

to see if bent.

-6-

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING THE MACHINE

-7-

Download from Www.Somanuals.com. All Manuals Search And Download.

FOOT CONTROLLER

For this machine use foot controller type YSD 180034.

-9-

Download from Www.Somanuals.com. All Manuals Search And Download.

BOBBIN WINDING

REMOVING THE BOBBIN

1.Remove the slide cover by sliding the

locker to right and push down the left

corner of slide cover.

At the same time.

2.Remove the bobbin from the machine.

WINDING THE BOBBIN

1.Pivot spool pin into highest horizontal spool pin position.

2.Pass a spool of thread on the spool pin. Secure to place a spool of thread on the pin.

Secure it with the spool cap to ensure smooth flow of thread.

3.Pass thread from spool through thread guides as shown.

4.Pull end of thread through hole in bobbin as shown.

5.Make sure the bobbin winder shaft is in left position. Place bobbin onto shaft with end

of thread coming from top of bobbin. Push bobbin winder shaft to right until it

clicks. Hold onto end of thread.

6.Start machine. The thread that is held will snap or may be trimmed with a scissors.

Bobbin will cease turning when completely filled. Push shaft to left to remove

bobbin.

-11-

Download from Www.Somanuals.com. All Manuals Search And Download.

INSERTING THE BOBBIN

1. Place bobbin into bobbin holder with the

thread unwinding counter clockwise.

2. Draw thread into notch (A).

3. Pull thread toward the left and along the

inside of spring (B) until it slips into notch

of notch (A).

4. Pull thread out about 10 inches and replace

the slide cover.

-12-

Download from Www.Somanuals.com. All Manuals Search And Download.

Shure Headphones I4C User Manual
Shure Microphone PGA81 User Manual
Sony Digital Camera 3 700 727 121 User Manual
Sony Stereo System CDX M8800 User Manual
Spirit Treadmill XT185 User Manual
Sterling Plumbing Outdoor Shower 72120106 User Manual
Sundance Spas Hot Tub 880 850 User Manual
SVAT Electronics Caller ID Box CID100 User Manual
Sylvania CRT Television 6620LG User Manual
Tanita Scale BF 572 User Manual