Model UA845 User Guide
ANTENNA DISTRIBUTION SYSTEM
USER'S GUIDE
©2006, Shure Incorporated
Printed in U.S.A.
27F8635 (Rev. 8)
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY INFORMATION ........................................................................................................... 5
MODEL UA845 ANTENNA DISTRIBUTION SYSTEM .............................................................. 7
ENGLISH
SYSTEM FEATURES ................................................................................................................ 7
CONTROLS AND CONNECTORS ............................................................................................ 8
SYSTEM INSTALLATION ......................................................................................................... 9
CONNECTING RECEIVERS ................................................................................................... 10
SPECIFICATIONS ................................................................................................................... 12
LICENSING AND WARRANTY INFORMATION ..................................................................... 13
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
! IMPORTANT SAFETY INSTRUCTIONS !
1.
2.
3.
4.
5.
6.
7.
READ these instructions.
KEEP these instructions.
HEED all warnings.
FOLLOW all instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Install in accordance with the manu-
facturer's instructions.
DO NOT install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
DO NOT defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wider blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
11. ONLY USE attachments/accessories specified by the manufacturer.
USE only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
12.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of
time.
8.
9.
14. REFER all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled
with liquids, such as vases, on the apparatus.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
! CONSIGNES DE SÉCURITÉ IMPORTANTES !
1.
2.
3.
4.
5.
6.
7.
LIRE ces consignes.
CONSERVER ces consignes.
OBSERVER tous les avertissements.
SUIVRE toutes les consignes.
NE PAS utiliser cet appareil à proximité de l'eau.
NETTOYER UNIQUEMENT avec un chiffon sec.
NE PAS obstruer les ouvertures de ventilation. Installer en respectant les con-
signes du fabricant.
Ne pas installer à proximité d'une source de chaleur telle qu'un radiateur, une
bouche de chaleur, un poêle ou d'autres appareils (dont les amplificateurs) pro-
duisant de la chaleur.
NE PAS détériorer la sécurité de la fiche polarisée ou de la fiche de terre. Une
fiche polarisée comporte deux lames dont l'une est plus large que l'autre. Une
fiche de terre comporte deux lames et une troisième broche de mise à la terre.
La lame la plus large ou la troisième broche assure la sécurité de l'utilisateur. Si
la fiche fournie ne s'adapte pas à la prise électrique, demander à un électricien
de remplacer la prise hors normes.
10. PROTÉGER le cordon d'alimentation afin que personne ne marche dessus et que
rien ne le pince, en particulier au niveau des fiches, des prises de courant et du point
de sortie de l'appareil.
11. UTILISER UNIQUEMENT les accessoires spécifiés par le fabricant.
12.
UTILISER uniquement avec un chariot, un pied, un trépied,
un support ou une table spécifié par le fabricant ou vendu
avec l'appareil. Si un chariot est utilisé, déplacer l'ensemble
chariot-appareil avec précaution afin de ne pas le renverser,
ce qui pourrait entraîner des blessures.
8.
9.
13. DÉBRANCHER l'appareil pendant les orages ou quand il ne sera pas utilisé pendant
longtemps.
14. CONFIER toute réparation à du personnel qualifié. Des réparations sont nécessaires
si l'appareil est endommagé de quelque façon que ce soit, comme par exemple : cor-
don ou prise d'alimentation endommagé, liquide renversé ou objet tombé à l'intérieur
de l'appareil, exposition de l'appareil à la pluie ou à l'humidité, appareil qui ne marche
pas normalement ou que l'on a fait tomber.
15. NE PAS exposer cet appareil aux égouttures et aux éclaboussements. NE PAS poser
des objets contenant de l'eau, comme des vases, sur l'appareil.
Ce symbole indique la présence d'une tension dangereuse dans
l'appareil constituant un risque de choc électrique.
Ce symbole indique que la documentation fournie avec l'appareil contient
des instructions d'utilisation et d'entretien importantes.
! WICHTIGE SICHERHEITSHINWEISE !
1.
2.
3.
4.
5.
6.
7.
Diese Hinweise LESEN.
Diese Hinweise AUFHEBEN.
Alle Warnhinweise BEACHTEN.
Alle Anweisungen BEFOLGEN.
11. NUR das vom Hersteller angegebene Zubehör und entsprechende Zusatzgeräte ver-
wenden.
NUR in Verbindung mit einem vom Hersteller angegebenen oder mit
dem Gerät verkauften Transportwagen, Stand, Stativ, Träger oder
Tisch verwenden. Wenn ein Transportwagen verwendet wird, beim
Verschieben der Transportwagen-Geräte Einheit vorsichtig vorgehen,
um Verletzungen durch Umkippen zu verhüten.
12.
Dieses Gerät NICHT in der Nähe von Wasser verwenden.
NUR mit einem sauberen Tuch REINIGEN.
KEINE Lüftungsöffnungen verdecken. Gemäß den Anweisungen des Herstell-
ers einbauen.
Nicht in der Nähe von Wärmequellen, wie Heizkörpern, Raumheizungen,
Herden oder anderen Geräten (einschließlich Verstärkern) installieren, die
Wärme erzeugen.
Die Schutzfunktion des Schukosteckers NICHT umgehen. Bei Steckern für die
USA gibt es polarisierte Stecker, bei denen ein Leiter breiter als der andere ist;
US-Stecker mit Erdung verfügen über einen dritten Schutzleiter. Bei diesen
Steckerausführungen dient der breitere Leiter bzw. der Schutzleiter Ihrer
Sicherheit. Wenn der mitgelieferte Stecker nicht in die Steckdose passt, einen
Elektriker mit dem Austauschen der veralteten Steckdose beauftragen.
13. Das Netzkabel dieses Geräts während Gewittern oder bei längeren Stillstandszeiten
aus der Steckdose ABZIEHEN.
8.
9.
14. Alle Reparatur- und Wartungsarbeiten von qualifiziertem Kundendienstpersonal
DURCHFÜHREN LASSEN. Kundendienst ist erforderlich, wenn das Gerät auf
irgendwelche Weise beschädigt wurde, z.B. wenn das Netzkabel oder der
Netzstecker beschädigt wurden, wenn Flüssigkeiten in das Gerät verschüttet wurden
oder Fremdkörper hineinfielen, wenn das Gerät Regen oder Feuchtigkeit ausgesetzt
war, nicht normal funktioniert oder fallen gelassen wurde.
15. Dieses Gerät vor Tropf- und Spritzwasser SCHÜTZEN. KEINE mit Wasser gefüllten
Gegenstände wie zum Beispiel Vasen auf das Gerät STELLEN.
10. VERHINDERN, dass das Netzkabel gequetscht oder darauf getreten wird, ins-
besondere im Bereich der Stecker, Netzsteckdosen und an der Austrittsstelle
vom Gerät.
Dieses Symbol zeigt an, dass gefährliche Spannungswerte,
die ein Stromschlagrisiko darstellen, innerhalb dieses
Geräts auftreten
Dieses Symbol zeigt an, dass das diesem Gerät beiliegende
Handbuch wichtige Betriebs- und Wartungsanweisungen enthält.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
! INSTRUCCIONES IMPORTANTES DE SEGURIDAD !
1.
2.
3.
4.
5.
6.
7.
LEA estas instrucciones.
CONSERVE estas instrucciones.
PRESTE ATENCION a todas las advertencias.
SIGA todas las instrucciones.
NO utilice este aparato cerca del agua.
LIMPIESE UNICAMENTE con un trapo seco.
NO obstruya ninguna de las aberturas de ventilación. Instálese según lo
indicado en las instrucciones del fabricante.
No instale el aparato cerca de fuentes de calor tales como radiadores, registros
de calefacción, estufas u otros aparatos (incluyendo amplificadores) que
produzcan calor.
NO anule la función de seguridad del enchufe polarizado o con clavija de
puesta a tierra. Un enchufe polarizado tiene dos patas, una más ancha que la
otra. Un enchufe con puesta a tierra tiene dos patas y una tercera clavija con
puesta a tierra. La pata más ancha o la tercera clavija se proporciona para su
seguridad. Si el tomacorriente no es del tipo apropiado para el enchufe, con-
sulte a un electricista para que sustituya el tomacorriente de estilo anticuado.
10. PROTEJA el cable eléctrico para evitar que personas lo pisen o estrujen, particular-
mente en sus enchufes, en los tomacorrientes y en el punto en el cual sale del
aparato.
11. UTILICE únicamente los accesorios especificados por el fabricante.
UTILICESE únicamente con un carro, pedestal, trípode,
escuadra o mesa del tipo especificado por el fabricante o ven-
dido con el aparato. Si se usa un carro, el mismo debe mov-
erse con sumo cuidado para evitar que se vuelque con el
aparato.
12.
8.
9.
13. DESENCHUFE el aparato durante las tormentas eléctricas, o si no va a ser utilizado
por un lapso prolongado.
14. TODA reparación debe ser llevada a cabo por técnicos calificados. El aparato
requiere reparación si ha sufrido cualquier tipo de daño, incluyendo los daños al
cordón o enchufe eléctrico, si se derrama líquido sobre el aparato o si caen objetos
en su interior, si ha sido expuesto a la lluvia o la humedad, si no funciona de modo
normal, o si se ha caído.
15. NO exponga este aparato a chorros o salpicaduras de líquidos. NO coloque objetos
llenos con líquido, tales como floreros, sobre el aparato.
Este símbolo indica que la literatura que acompaña a esta
unidad contiene instrucciones importantes de funcionamiento
y mantenimiento.
Este símbolo indica que la unidad contiene niveles de voltaje
peligrosos que representan un riesgo de choques eléctricos.
! ISTRUZIONI IMPORTANTI PER LA SICUREZZA !
1.
2.
3.
4.
5.
6.
7.
EGGETE queste istruzioni.
CONSERVATE queste istruzioni.
OSSERVATE tutte le avvertenze.
SEGUITE tutte le istruzioni.
10.
11.
12.
EVITATE di calpestare il cavo di alimentazione o di comprimerlo, specie in corrispon-
denza di spine, prese di corrente e punto di uscita dall'apparecchio.
USATE ESCLUSIVAMENTE i dispositivi di collegamento e gli accessori specificati
dal costruttore.
NON usate questo apparecchio vicino all'acqua.
USATE l'apparecchio solo con carrelli, sostegni, treppiedi,
staffe o tavoli specificati dal costruttore o venduti insieme
all'apparecchio stesso. Se usate un carrello, fate attenzione
durante gli spostamenti per evitare infortuni causati da un
eventuale ribaltamento del carrello stesso.
PULITE l'apparecchio SOLO con un panno asciutto.
NON ostruite alcuna apertura per l'aria di raffreddamento. Installate l'apparec-
chio seguendo le istruzioni del costruttore.
NON installate l'apparecchio accanto a fonti di calore quali radiatori, aperture
per l'efflusso di aria calda, forni o altri apparecchi (amplificatori inclusi) che gen-
erino calore.
NON modificate la spina polarizzata o con spinotto di protezione. Una spina polar-
izzata è dotata di due lame, una più ampia dell'altra. Una spina con spinotto è dot-
ata di due lame e di un terzo polo di messa a terra. La lama più ampia ed il terzo
polo hanno lo scopo di tutelare la vostra incolumità. Se la spina in dotazione non si
adatta alla presa di corrente, rivolgetevi ad un elettricista per far eseguire le modi-
fiche necessarie.
8.
9.
13. SCOLLEGATE l'apparecchio dalla presa di corrente in caso di temporali o di non uti-
lizzo per un lungo periodo.
14. RIVOLGETEVI a personale di assistenza qualificato per qualsiasi intervento. È nec-
essario intervenire sull'apparecchio ogniqualvolta sia stato danneggiato, in qualsiasi
modo, ad esempio in caso di danneggiamento di spina o cavo di alimentazione, ver-
samento di liquido sull'apparecchio o caduta di oggetti su di esso, esposizione
dell'apparecchio a pioggia o umidità, funzionamento irregolare o caduta.
15. NON esponetelo a sgocciolamenti o spruzzi. NON appoggiate sull'apparecchio
oggetti pieni di liquidi, ad esempio vasi da fiori.
Questo simbolo indica la presenza di istruzioni importanti per
l'uso e la manutenzione nella documentazione in dotazione
all'apparecchio.
Questo simbolo indica la presenza di alta tensione all'interno
dell'apparecchio, che comporta il rischio di folgorazione.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL UA845 ANTENNA DISTRIBUTION SYSTEM
power
UA845
UHF Antenna Distribution System
The Shure Model UA845 is an amplified, UHF Antenna Distribu-
tion System that expands a wireless microphone system by splitting
one pair of antennas to multiple Shure U4 or Shure UC4 wireless
receivers. It also amplifies RF signals to compensate for insertion
loss due to splitting signal power to mulitple output connectors.
Each UA845 allows up to four receivers to use the same antennas.
CASCADE connectors allows connections to a fifth receiver or a
second UA845. There are also power connectors for powering
Shure UHF and UC Wireless systems.
The Shure Model UA845 ensures maximum sensitivity and sig-
nal processing capability, providing the widest radio range possible
for the largest number of wireless receivers. To get the most from
this system, follow these guidelines:
•
When using long runs of cable for remote-mounted antennas,
use the UA830 In-Line RF Amplifier and the Shure Model
UA825 or UA850 Remote Antenna Extension cables (RG-8/X
or equivalent), which have low loss at UHF operating frequen-
cies
•
Locate multiple transmitters more than 3 m [10 ft] from receiv-
ing antennas
Each system contains the following items:
•
•
•
•
•
•
•
•
UA845 Antenna Distribution System
Rack-mounting hardware
Surface-mounting hardware
Front-mounting antenna hardware
18-in. Power OUTPUT Cord
Power Cord
Antenna cables for receiver connections
DC power cables for receiver connections to DC power con-
nectors on UC receivers.
SYSTEM FEATURES
•
Expandability. The UA845 UHF Antenna Distribution System
is designed for large UHF wireless systems. Each unit allows
up to four wireless receivers to use the same two antennas,
and the CASCADE ports allow connection to a fifth receiver or
a second UA845.
•
Power OUTPUT and OUT Connectors. Up to five (5) U4 re-
ceivers can be daisy-chained and powered from a single
source via the Power OUTPUT connectors. Up to four (4) UC4
receivers can be powered from the UA845 using the 12 Vdc
OUT connectors.
•
•
Compatibility. The UA845 is compatible with all Shure wire-
less microphone receivers operating within a compatible fre-
quency range (see UHF Carrier Frequency Ranges in the
Specifications section).
•
•
Low Noise and Intermodulation Distortion. The UA845
maintains clean signals with minimal distortion.
Insertion Loss Compensation. Whenever a signal is split to
multiple output ports, there is a loss in signal strength. The
UA845 amplifies signals to compensate, ensuring a strong sig-
nal to the receivers.
CASCADE Ports. Two 50
Ω, BNC-type antenna CASCADE
ports allow an additonal UA845 unit or a fifth wireless receiver.
A large wireless system can be run off of a single pair of anten-
nas.
•
Front-Mounted Antennas. The UA845 comes with hardware
to front-mount the antennas, if desired.+
7
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTORS
Front Panel
UA845
UHF ANTENNA DISTRIBUTION SYSTEM
1
2
POWER INDICATOR
POWER ON/OFF
SWITCH
FRONT PANEL
FIGURE 1
Back Panel
6
6
1
2
3
4
5
3
4
5
BACK PANEL
FIGURE 2
AC Power INPUT Connector.
RF CASCADE Connectors (Output connector 5),
Channel A & B. BNC-type connectors for adding a fifth
receiver, or additional UA845's, permitting more wireless
receivers to be connected.
1
2
4
AC Power OUTPUT Connector. Each UA845 has a
Power OUTPUT connector for daisy-chaining up to five
(5) Shure Model U4 UHF Diversity Single or Dual Receiv-
ers to a single power source.
RF OUTPUT Connectors, Channel A & B. BNC-type
connectors for up to four wireless receivers.
5
6
NOTE: This connector does not work for Shure UC4
Receivers.
12 Vdc OUT Connectors. These power connectors are
designed to power up to four (4) Shure UC4 Wireless
systems.
ANTENNA IN Ports, Channel A & B. BNC-type connec-
tors for antennas.
3
ENGLISH
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM INSTALLATION
Installing Front-Mounted Antennas
Mounting the UA845 in an Equipment Rack
The UA845 comes equipped for front-mounted antennas.
Front-mounting improves RF performance of the system by moving
the antennas to the front of the rack. When a unit is located in a
rack, antennas should be either front- or remote-mounted.
NOTE: If front mounting the antennas, connect them before
mounting the UA845 in the rack. Once in the rack, it is more
difficult to insert the bulkhead adapters and connect the
antenna cables.
1. Insert the bulkhead adapters through the holes in each bracket,
and secure them from each side, using the supplied hardware.
1. Insert the unit into a 19-inch equipment rack.
2. Using the screws supplied, secure the unit to the rack.
power
UA845
UHF Antenna Distribution System
RACK MOUNTING
INSERTING BULKHEAD ADAPTERS
FIGURE 6
FIGURE 3
3. If the antennas are remote mounted from the back of the rack,
insert the supplied plastic plugs into the holes on the front of the
brackets.
2. Connect the supplied antenna cables to the receiver antenna
inputs and adapters.
Installing Remote Antennas
Remote-mounted antennas have the advantage of being free
from the unit and closer to the transmitters. They can be placed any-
where within the recommended cable length, creating a much wider
radio reception range and further reducing the possibility of signal
dropout. When remote-mounted antennas are desirable, please
ask your Shure dealer for information on the UA830 In-Line RF Am-
plifier. Cables are available in UA825 (7.5 m [25 ft]) and UA850 (15
m [50 ft]) versions.
UA845
CONNECT ANTENNA CABLES
power
UA845
UHF Antenna Distribution System
FIGURE 4
power
UA845
UHF Antenna Distribution System
power
UA845
UHF Antenna Distribution System
3. Install the antennas onto the bulkhead adapters protruding
through the front panel. See 5.
RECEIVERS
power
UA845
UHF Antenna Distribution System
ATTACH ANTENNAS TO THE ADAPTERS
FIGURE 5
REMOTE-MOUNTED ANTENNAS
NOTE: For the best results, point the antennas up and away
from each other at 45° angles from vertical. This ensures the
best possible reception and greatly reduces the possibility of
signal dropout. Always perform a walk-through test of the
system in the performing area before using a wireless system.
FIGURE 7
9
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING RECEIVERS
Single UA845 Setup
3. To daisy-chain U4 Receivers together with Power OUTPUT
cables, connect the Power OUTPUT connector of the UA845 to
the Power INPUT connector of one receiver. Connect the
remaining receivers similarly. Connect the POWER INPUT of
the unit to a power supply.
1. Using low-loss, 50 Ω coaxial cables (RG-58 or equivalent), con-
nect the right and left (Channels 1 through 4, A and B) RF
OUTPUT ports on the UA845 to the corresponding left and
right antenna inputs on each receiver. Use the CASCADE ports
to connect a fifth receiver.
NOTE: No more than five (5) Shure UHF receivers should be
powered through a daisy-chain from a single UA845.
2. Using the supplied power cable, connect the UA845 to a power
outlet.
4. To power Shure UC4 receivers, connect the power input ports of
the UC4 receivers to the 12 Vdc OUT of the UA845. Up to four
UC4 Receivers can be powered.
UA845
12 VDC POWER CONNECTOR
ANT B IN
12 VDC POWER CONNECTOR
CASCADE B
CASCADE A
ANT A IN
ANT B OUTS
ANT A OUTS
AC PWR OUTPUT
AC PWR INPUT
TO POWER SUPPLY
ANT B IN
ANT A IN
AC PWR OUTPUT
AC PWR INPUT
U4 RECEIVER
U4 RECEIVER
U4 RECEIVER
UC4 RECEIVER
UC4 RECEIVER
12 VDC PWR INPUT
ANT A IN
ANT B IN
ANT A IN
ANT B IN
SINGLE UA845 SETUP
FIGURE 8
ENGLISH
10
Download from Www.Somanuals.com. All Manuals Search And Download.
remaining receivers similarly. Connect the POWER INPUT of
the unit to an AC power supply.
Multiple UA845 Setup
1. Connect the CASCADE ports (connector 5) for RF OUTPUT
Channels A and B of one UA845 to the ANTENNA INPUT,
channels A and B, of a U4 receiver, a UC4 receiver, or a sec-
ond UA845.
WARNING: When adding additional UA845's to a system,
each UA845 should be connected to a separate power
supply. No more than five (5) receivers can be powered
from a single UA845. Daisy-chaining multiple UA845's
through the Power OUTPUT ports will overload a single
power supply, possibly causing damage to the equipment.
2. If desired, connect additional units in the same manner.
3. To daisy-chain U4 Receivers together with Power OUTPUT
cables, connect the Power OUTPUT connector of the UA845 to
the Power INPUT connector of one receiver. Connect the
4. To power Shure UC4 receivers, connect the power input ports of
the UC4 receivers to the 12 Vdc OUT of the UA845. Up to four
UC4 Receivers can be powered.
12 VDC POWER CONNECTOR
UA845
12 VDC POWER CONNECTOR
ANT B IN
ANT A IN
CASCADE A
CASCADE B
ANT B OUTS
AC PWR OUTPUT
ANT A OUTS
AC PWR INPUT
TO POWER SUPPLY
TO
TO
RECEIVERS
RECEIVERS
AC PWR OUTPUT
AC PWR INPUT
ANT A IN
ANT B IN
U4 RECEIVER
U4 RECEIVER
12 VDC PWR INPUT
ANT A IN
ANT B IN
UA845
TO POWER SUPPLY
TO
TO RECEIVERS
RECEIVERS
U4 RECEIVER
TO UA845
ANT A IN
TO UA845 ANT B IN
MULTIPLE UA845 SETUP
FIGURE 9
11
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
UHF Carrier Frequency Range
Certification
UA845-UA.....................................................782–806 MHz
UA845-UB.....................................................692–716 MHz
UA845-MA.....................................................782–810 MHz
UA845-MB.....................................................800–830 MHz
UA845-KK .....................................................838–862 MHz
UA845-MC ....................................................774–782 MHz
UA845 US .....................................................500–900 MHz
UA845 UK .....................................................500–900 MHz
UA845 E........................................................500–900 MHz
Distributed Output Level (Gain)
Models UA845-UA, UB, MA, MB, KK, MC:
3.5 dB typical, 2.0 dB to 5.0 dB from antenna input
(Output ports 1–4).
0.5 dB typical, –1.0 dB to 2.0 dB from antenna input
(Cascade port)
UA845: LISTED by UL and CUL (U.S. and Canada), IC and
FCC; IC Certified (Canada). Meets applicable European direc-
tives for CE marking eligibility. VDE GS-Certified. Meets Re-
quirements of EMC Standard and 301 489 Parts 1 and 9. Meets
the essential requirements of the European R&TTE Directive
99/5/EC and are eligible to carry the CE marking.
Furnished Accessories
2 ft. Coaxial Antenna Cable (RG-58) (12).................UA802
Optional Accessories
1/2-Wave Antenna
UA820A.......................................................(774–865 MHz)
UA820B.......................................................(690–746 MHz)
UA820C.......................................................(662–698 MHz)
UA820D.......................................................(554–590 MHz)
UA820E.......................................................(746–784 MHz)
25 ft. Coaxial Cable (RG-8/X) ...................................UA825
50 ft. Coaxial Cable (RG-8/X) ...................................UA850
30.4 m (100 ft.) Antenna Extension Cable .............UA8100
In-Line RF Amplifier
UA830A.......................................................(782–810 MHz)
UA830UB ....................................................(692–716 MHz)
UA830C.......................................................(800–830 MHz)
UA830D.......................................................(774–782 MHz)
UA830KK ....................................................(838–862 MHz)
UA830WB ...................................................(470–900 MHz)
Active Directional Antenna
ModelsUA845 US, UK and E:
3 dB typical, 0 dB to 3.5 dB from antenna input
(Output ports 1–4)
1 dB typical, –1.6 dB to +1.8 dB from antenna input
(Cascade port)
Output Connector Isolation
Greater than 25 dB
Third Order Intercept Point (3 OIP)
Typical 24 dBm
Input/Output AC Line Voltage
100 to 240 Vac, 50/60 Hz, unswitched
DC Output Voltage
12 Vdc, 4 connectors
Maximun Current Supply from DC Outputs
1.1 Amps
Impedance
50 Ω
Operating Temperature Range
–7° C (+20° F) to 49° C (+120° F)
Overall Dimensions
44.5 mm high x 482.6 mm wide x 295.3 mm deep
(1 3/4 x 19 5/8 x 11inches)
Net Weight
UA870A ......................................................(782–810 MHz)
UA870MB....................................................(800–830 MHz)
UA870MC....................................................(774–782 MHz)
UA870KK ....................................................(838–862 MHz)
UA870UB ....................................................(692–716 MHz)
UA870WB ...................................................(470–900 MHz)
Replacement Parts
3.32 Kg (7 lbs, 5 oz)
Input/Output Antenna Connector Type
BNC-type
AC Power Consumption
Hardware Kit ....................................................... 90VL1371
Bulkhead Adapters................................................ 95A8647
120 VAC Power Line Cord .................................... 95A8389
230 VAC Power Line Cord .................................... 95A8247
240 VAC Power Line Cord (U.K.).......................... 95A8713
120 VAC, 16-in. Power-Through Cord .................. 95A8576
230 VAC, 18-in. Power-Through Cord .................. 95A8678
12 Vdc Power Cables............................................ 95A8420
15 W per unit typical. When used with 4 UC4's, 55 W max.
THIS RADIO EQUIPMENT IS INTENDED FOR USE IN MUSICAL PROFESSIONAL ENTERTAINMENT AND SIMILAR
APPLICATIONS.
NOTE: THIS RADIO APPARATUS MAY BE CAPABLE OF OPERATING ON SOME FREQUENCIES NOT AUTHORIZED IN
YOUR REGION. PLEASE CONTACT YOUR NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED
FREQUENCIES FOR WIRELESS MICROPHONE PRODUCTS IN YOUR REGION
ENGLISH
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LICENSING AND WARRANTY INFORMATION
Warranty. Shure Incorporated (“Shure”) hereby warrants that
these products will be free from defects in material and workman-
ship for a period of two years from the date of purchase. At its op-
tion, Shure will repair or replace the defective product and promptly
return it to you, or refund the purchase price. Retain proof of pur-
chase to validate the purchase date and return it with any warranty
claim. If you believe this product is defective within the warranty pe-
riod, carefully repack the unit, insure it, and return it postpaid to:
Shure Incorporated
scription of the problem. Do not mail any units or parts to Shure un-
less requested to do so by Shure's Service Department. Any
returned items must have prior authorization. Unauthorized returns
are delayed in handling; these delays can be avoided by contacting
Shure in advance and furnishing the necessary information.
Shure reserves the right to make design changes and product
improvements on any previously manufactured products. Shure
also reserves the right to ship new and/or improved products which
are similar to the form, fit and function of the originally ordered prod-
ucts.
Attention: Service Department
5800 W. Touhy Avenue
Niles, IL 60714-4608 U.S.A.
For service outside the United States, return the product to your
authorized Shure Distribution Center.
All claims of defects or shortage should be directed to the above
address. Please furnish model number, operating frequency, and
date, place and proof of purchase (such as a copy of your sales re-
ceipt) to establish warranty. Your letter should include all pertinent
details including applicable model or part numbers and a brief de-
Licensing. Changes or modifications not expressly approved by
Shure Incorporated could void your authority to operate the equip-
ment. Licensing of Shure wireless microphone equipment is the us-
er's responsibility, and licensability depends on the user's
classification and application, and on the selected frequency. Shure
strongly urges the user to contact the appropriate telecommunica-
tions authority concerning proper licensing, and before choosing
and ordering frequencies other than standard frequencies.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
ITALIANO
42
Download from Www.Somanuals.com. All Manuals Search And Download.
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
Download from Www.Somanuals.com. All Manuals Search And Download.
|