SHINDAIWA OWNER’S/OPERATOR’S MANUAL
T254 TRIMMER
WARNING!
Minimize the risk of injury to yourself and
others! Read this manual and familiarize yourself
with the contents. Always wear eye and hearing pro-
tection when operating this unit.
X7502825100
04/10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Operational Labels
WARNING: Surface can be hot. Al-
ways wear gloves when handling
this unit.
Make sure no one is within
15 M / 50 feet of an operating
machine.
Read and follow this operator's
manual. Failure to do so could
result in serious injury..
50 FEET
(15m)
HOT SURFACE
Beware of thrown or
richocheted objects
Wear eye and hearing protection
at all times during operation of
this unit. Wear head protection
where there is a risk of falling
objects.
Safety
Work Safely
Trimmers and brushcutters operate at very high speeds and can do serious damage or injury if they are misused or abused.
Never allow a person without training or instruction to operate this unit!
WARNING!
Never make unauthorized modifications or attachment
installations. Never use attachments not approved by
Shindaiwa for use on this unit.
WARNING!
Never operate power equipment of
any kind if you are tired or if you are under
the influence of alcohol, drugs, medication or any other
substance that could affect your ability or judgement.
Stay Alert
You must be physically and mentally fit to operate this unit
safely.
WARNING!
WARNING!
Moving parts can amputate fingers or cause
severe injuries. Keep hands, clothing and loose
objects away from all openings.
Use Good Judgment
ALWAYS inspect unit before each use. Replace any
damaged parts.
• ALWAYS stop engine, disconnect spark plug, and
make sure all moving parts have come to a com-
NEVER run the engine when transporting the unit.
NEVER run the engine indoors! Make sure there is
always good ventilation. Fumes from engine exhaust
can cause serious injury or death.
plete stop
debris, or servicing unit.
before removing obstructions, clearing
• DO NOT start or operate unit unless all guards and
protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is
running. Moving parts may not be visible through
openings.
ALWAYS stop the unit immediately if it suddenly begins
to vibrate or shake. Inspect for broken, missing or
improperly installed parts or attachments.
NEVER extend trimming line beyond the length specified
for your unit.
ALWAYS keep the unit as clean as practical. Keep it free
of loose vegetation, mud, etc.
WARNING!
ALWAYS hold the unit firmly with both hands when cut-
Operation of this equipment may create sparks
that can start fires around dry vegetation. This
unit is equipped with a spark arrestor and a spark
arrestor may be required. The operator should
contact local fire agencies for laws or regulations
relating to fire prevention requirements.
ting or trimming, and maintain control at all times.
ALWAYS use the proper cutting tool for the job.
ALWAYS keep the handles clean
ALWAYS disconnect the spark plug wire before perform-
ing any maintenance work.
WARNING!
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon-
sciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is
directed away from your face and body.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Labels
READ THE
OPERATOR’S MANUAL
HOT SURFACE
WEAR HEARING AND ANSI Z87.1
APPROVED EYE PROTECTION
50 FEET
(15m)
KEEP BYSTANDERS AWAY
AT LEAST 50 FEET (15m)
BEWARE OF THROWN OR
RICOCHETED OBJECTS
This label indicates the minimum distance between
front handle and rear grip per ANSI B175.3.
DO NOT OPERATE THIS
MACHINE WITH
A
BLADE
Shindaiwa Inc.
19422-00028
IMPORTANT!
Safety and Operation Information Labels: Make sure
all information labels are undamaged and readable.
Immediately replace damaged or missing information
labels. New labels are available from your local autho-
rized Shindaiwa dealer.
The Properly Equipped Operator
Wear hearing protection devices and a
broad-brimmed hat or helmet. A helmet
is required when using a blade-equipped
brushcutter to clear small trees.
Always wear eye protection such as
goggles or safety glasses to shield
against thrown objects.
Prolonged exposure to excessive noise
is fatiguing and could lead to impaired
hearing.
Always wear a harness when operating the unit .
It adds comfort and helps ensure safety by limiting
movement fore and aft. When the harness is
adjusted properly, the unit should balance with the
cutting attachment parallel to the ground.
Wear close-fitting clothing to
protect legs and arms. Gloves
offer added protection and are
strongly recommended. Do not
wear clothing or jewelry that
could get caught in machinery
or underbrush. Secure long hair
so that it is above shoulder level.
NEVER wear shorts!
Always operate with both hands
firmly gripping the unit.
Always make sure the
appropriate cutting attachment
shield is correctly installed and
in good condition. Do not
operate the unit if the
Long-term exposure to vibration
can damage your hands.
cutting attachment shield
is missing, loose, or
Keep a proper footing and do not
overreach. Maintain your balance at all
times during operation.
broken.
Wear appropriate footwear (non-skid
boots or shoes): do not wear open-
toed shoes or sandals. Never work
barefooted!
Keep away from the rotating
trimmer line at all times, and
never lift a moving attachment
above waist-high.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Be Aware of the Working Environment
Make sure
bystanders
Reduce the risk of bystanders being
struck by flying debris. Make sure no
one is within 15 meters (50 feet)—
that’s about 16 paces of an operating
attachment. Stop immediately if a child,
pet, or person comes within a 15 meter
(50 feet)radius. Outside this radius,
there is still a risk of injury from thrown
objects.
or observers
outside the
Avoid long-term
operation in very hot
or very cold weather.
15 meter (50
feet) “danger
zone” wear eye
protection.
15 METERS
(50 FEET)
Always make sure
the appropriate
cutting attachment
shield is correctly
installed.
Be extremely careful
of slippery terrain,
especially during rainy
weather.
Do not operate the unit
if the cutting attachment
shield is missing, loose,
or broken.
Be constantly alert for
objects and debris that
could be thrown either
from the rotating cutting
attachment or bounced
from a hard surface.
ALWAYS clear your work area of trash
or hidden debris that could be thrown
back at you or toward a bystander.
When operating in rocky terrain or
near electric wires or fences, use
extreme caution to avoid contacting
such items with the cutting attachment.
If contact is made with a hard object,
stop the engine and inspect the cutting
attachment for damage.
Product Description
Using the illustration as a guide, familiarize your-
self with your machine and its various compo-
nents. Understanding your machine helps ensure
top performance, long service life and safer
operation.
Throttle
Interlock
Spark plug
Ignition
Switch
Handle
Fuel
Tank
Throttle
Lever
Outer Tube
Grip
Gearcase
Cutting Attachment
Shield
Trimmer Head
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Engine Name
T254
4-cycle, vertical cylinder, air cooled
5.0 kg/11.0 lb.
Engine Type
Dry Weight (Without guard and strap)
Bore x Stroke
34 x 27 mm (1.3 x 1.1 in.)
24.5 cc (1.5 cu. in.)
Displacement
Fuel/Oil Ratio
50:1 with *ISO-L-EGD or JASO FD class engine oil
590 ml (20 oz.)
Fuel Tank Capacity
Carburetor Type
Ignition
Diaphragm-type carburetor
One-piece electronic, program-controlled
NGK CMR5H
Spark Plug**
Spark Plug Gap
Torque
0.6 mm (0.024 in)
16.7 - 18.6 N∙m (148-165 in • lbf)
Foam pre-filter; sealed felt main filter
Recoil
Air Cleaner Type
Starting Method
Stopping Method
Slide switch
Transmission Type
Engine Idle Speed
Clutch Engagement Speed
Automatic, centrifugal clutch w/bevel gear
3,000 RPM
4,100 RPM
Wide Open Throttle Speed (W.O.T.)
10,500 RPM
Specifications are subject to change without notice.
Emission Control (Exhaust & Evaporative)
EPA 2010 and Later and/or C.A.R.B. TIER III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to
California models only.
An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY; information on label varies by en-
gine FAMILY).
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine
emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
Assembly
IMPORTANT!
The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the
operator during normal operation.
Prior to Assembly
Before assembling, make sure you have all the components required for a complete unit and inspect unit and components
for any damage.
■ Kit containing cutting attachment shield, mounting
■ Engine and shaft assembly
bracket and hardware, this owner’s/operator’s manual
and tool kit for routine maintenance. Tool kits vary by
model and may include a spark plug/screwdriver combi-
■ Cutting attachment shield
■ Cutting attachment
nation wrench, and a scraper.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutting attachment shield
CAUTION
A
Wear Gloves or personal injury may result:
• Cutoff knife is sharp.
• Gearcase and surrounding area may be hot.
NOTE
The plastic shield is for use with the Nylon Line Head only. Install Metal
Shield when using plastic or metal blades.
B
C
1. Remove plastic threaded shaft sleeve and adapter plate (C) from
PTO shaft (A).
2. Place the shield on the bottom of the bearing housing flange.
3. Place shield plate (B) on shield, align holes. Install three (3) screws
from bottom through plate and shield into gear case.
4. Assemble adapter plate (C) onto PTO shaft.
D
Install trimmer head
A
NOTE
Use the 4 mm hexagonal wrench as a gear housing locking tool.
1. Be sure adapter plate (C) remains on PTO shaft (A).
2. Align locking hole in upper plate with notch in edge of gear housing
and insert head locking tool (D).
3. Thread line head (E) onto shaft by turning it counter-clockwise until
head is tight against adapter plate (C).
C
4. Remove locking tool (D).
IMPORTANT
Semi-automatic nylon line heads must be used only with plastic debris shield
with cut-off knife. Using nylon line heads with metal debris shield can result
in trimmer damage, caused by operation with excessive line length.
D
To advance trimmer line
Tip:
To advance trimmer line, tap trimmer head against the ground while the head
is turning at normal operating speed.
E
Nylon line replacement
See Maintenance Section for Loading Trimmer Line.
Remove nylon line head
NOTE
Do not disassemble nylon line head.
1. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (D).
2. Remove line head (E) by turning it clockwise until head is completely off of shaft.
3. Remove locking tool (D).
WARNING!
A standard grass trimmer with a loop handle should NEVER be operated with blade-type attachments. For
blade use, the trimmer must be fitted with a bicycle-type handlebar or a barrier bar that is located in front of the opera-
tor to reduce the risk of the operator from coming in contact with the cutting attachment (per ANSI B175.3). When
using a blade, the unit must also be equipped with a harness or strap.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front handle installation
NOTE
Label shows minimum spacing for front handle location.
1. Position front handle for comfortable operation and secure screws.
Adjust throttle lever free play
The throttle lever free play should be approximately 4 - 6 mm (3/16” -
1/4”). Make sure that the throttle lever operates smoothly without binding.
If it becomes necessary to adjust the lever free play, follow the procedures
and illustrations that follow.
4-6 mm
(3/16”-1/4”)
Throttle Free Play
Throttle lever free play
1. Loosen the air cleaner cover knob(s) and remove the air cleaner cover.
2. Turn the cable adjuster in or out as required to obtain proper free play
4 - 6 mm (3/16 - 1/4 in).
3. Reinstall the air cleaner cover.
Remove air cleaner cover
Cable
Adjuster
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Mixing Fuel
WARNING!
Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa
requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause
performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including,
but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel
lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain
up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood
alcohol) is NOT approved.
Hybrid 4TM Mixture Oil - Engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be
used. Shindaiwa highly recommends using Shindaiwa Red ArmorTM engine oil in all Shindaiwa Hybrid 4TM engines to
protect the engine from harmful carbon build up, maintain engine performance, and increase engine life. Shindaiwa
Red ArmorTM engine oil exceeds ISO-L-EGD and J.A.S.O. M345/FD performance requirements. Engine problems
due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD certified
oil will void the engine warranty.
Examples of 50:1 mixing quantities
IMPORTANT!
Shindaiwa Red ArmorTM engine oil may be mixed at 50:1 ratio for application
in all Shindaiwa engines sold in the past, regardless of ratio specified in those
manuals.
IMPORTANT!
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30)
days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improp-
erly mixed, or stale fuel, may cause hard starting, poor performance, or severe
engine damage and void the product warranty. Read and follow instructions in
the Long Term Storage section of this manual.
Handling Fuel
DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury
may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Mixing Instructions
1. Fill an approved fuel container with half of the required
amount of gasoline.
2. Add the proper amount of engine oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and
remix.
Storage - Fuel storage laws vary by locality. Contact
your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight con-
tainer. Store in a well-ventilated, unoccupied building,
away from sparks and flames.
IMPORTANT!
IMPORTANT!
Stored fuel may separate. ALWAYS shake fuel container
thoroughly before each use.
Spilled fuel is a leading cause of hydrocarbon emissions.
Some states may require the use of automatic fuel shut-
off containers to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can
occur. Return unused fuel to an approved fuel storage
container.
Filling the fuel tank
WARNING!
Minimize the Risk of Fire
■ ALWAYS store gasoline in a container approved for
■ NEVER smoke or light fires near the engine.
flammable liquids.
■ ALWAYS stop the engine and allow it to cool before
■ ALWAYS inspect the unit for fuel leaks before each
use. During each refill, check that no fuel leaks from
around the fuel cap and/or fuel tank.
refueling.
■ ALWAYS Wipe all spilled fuel and move at least 3
meters (10 feet) from the fueling point and source before
starting.
If fuel leaks are evident, stop using the unit immedi-
ately. Fuel leaks must be repaired before using the unit.
■ NEVER place flammable material close to the engine
■ ALWAYS move the unit at least 3 meters (10 feet)
away from a fuel storage area or other readily flam-
mable materials before starting
muffler.
■
NEVER operate the engine without the muffler and spark
arrester screen in place and in good working condition.
the engine.
■ FUEL IS HIGHLY FLAMMABLE.
1. Place the unit on a flat, level surface.
2. Clear any dirt or other debris from around the fuel filler cap.
CAUTION!
Slowly remove the fuel cap only after stopping the engine.
3. Remove the fuel cap, and fill the tank with clean, fresh fuel.
4. Reinstall the fuel filler cap and tighten firmly.
5. Wipe away any spilled fuel before starting engine.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Engine
IMPORTANT!
Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF
or STOP.
WARNING!
Never start the engine from the operating position.
1. Slide the ignition switch to the “ON” position.
2. Set the throttle lever to the “fast idle”:
Throttle
Interlock
ON
a.Depress and hold the throttle interlock, then squeeze the throttle lever.
b.Depress and hold the fast idle button.
c. Release the throttle lever and throttle interlock, then release fast idle
button.
Fast Idle
Button
Throttle
Lever
Slide ignition to ON
3. Press the primer bulb until fuel can be seen flowing in the transparent
return tube.
Primer Bulb
IMPORTANT!
The primer system only pushes fuel through the carburetor. Repeatedly
pressing the primer bulb will not flood the engine with fuel.
Press primer bulb...
4. Set the choke lever to the CLOSED position if engine is cold.
Close
choke
Set the choke lever to the CLOSED position
5. While holding the outer tube firmly with left hand. Use your other hand to
Hold
slowly pull the recoil starter handle until resistance is felt, then pull quickly
to start the engine.
the unit
firmly...
CAUTION!
Do not pull the recoil starter to the end of the rope travel. Pulling the recoil
starter to the end of the rope travel can damage the starter.
WARNING!
The cutting attachment may move when the engine is started!
Make sure the
...and pull recoil
attachment is clear
starter handle
of obstructions!
upward
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6. When the engine starts, slowly move the choke lever to the “OPEN” posi-
tion. (If the engine stops after the initial start, close the choke and restart.)
7. Operating the throttle will automatically disengage the fast idle setting.
Open
IMPORTANT!
If the engine fails to start after several attempts with the choke in the closed
position, the engine may be flooded with fuel. If flooding is suspected, refer
to the ”Starting a Flooded Engine” section of this manual.
After engine starts, move choke to OPEN
position
When the Engine Starts...
■ After the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.
■ After the engine is warm, pick up the unit and clip on the shoulder strap, if so equipped.
■
Squeezing the throttle makes the cutting attachment move faster; releasing the throttle permits the attachment to stop moving. If
the cutting attachment continues to move when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting
Engine Idle”).
Starting A Flooded Engine
1. Slide the ignition switch to the “I” (ON) position.
2. Open the choke, hold the throttle lever in the full throttle position, then
clear excess fuel from the combustion chamber by cranking the engine
several times.
3. If the engine still fails to start or fire, refer to the troubleshooting flow chart
at the end of this manual.
Stopping the Engine
Idle the engine briefly before stopping (about 2 minutes), then slide the igni-
tion switch to the “O” (Engine OFF) position.
OFF
Slide ignition to OFF
Checking Unit Condition
NEVER operate the unit with the cutting attachment shield or other protec-
tive devices removed!
NEVER allow the engine to run at high
RPM without a load. Doing so could dam-
age the engine.
Use only authorized Shindaiwa parts and accessories with your Shindaiwa
trimmer. Do not make modifications to this unit without written approval from
Shindaiwa, Inc.
NEVER operate a unit with worn or dam-
aged fasteners or attachment holders.
ALWAYS make sure the cutting attachment is properly installed and firmly
tightened before operation.
WARNING!
NEVER use a cracked or warped cutting attachment; replace it with a
A cutting attachment shield or
other protective device is no guaran-
tee of protection against ricochet. YOU
MUST ALWAYS GUARD AGAINST
FLYING DEBRIS!
serviceable one.
ALWAYS make sure the cutting attachment fits properly into the appropri-
ate attachment holder. If a properly installed attachment vibrates, replace the
attachment with new one and re-check.
ALWAYS stop the engine immediately and check for damage if you strike
a foreign object or if the unit becomes tangled. Do not operate with broken
or damaged equipment.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
WARNING
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon-
sciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is
directed away from your face and body.
Cutting grass with a trimmer head
Your Shindaiwa unit may be equipped with one of several Shindaiwa trimmer
head models, each with features for specific applications and/or operational
requirements.
NOTE:
For proper operation, always refer to the instructions accompanying the trim-
mer head being used.
CAUTION!
Trimmer head styles:
Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head
on the ground during operation.
■
Do not push the rotating line into trees,
wire fences or any material that could
tangle or break line ends.
■
Operation of trimmer without a cutting
attachment shield and using exces-
sive line length can lead to premature
clutch failure.
Manual. The operator indexes line manually with the grass trimmer stopped.
Fixed. The operator must stop the unit and add new lengths of trimmer line
manually.
Flail. This device, designed for clearing weeds and light brush, features three
nylon blades attached to the head by pivots.
■ Operation at low rpm can lead to
premature clutch failure.
NOTE:
Additional hardware may be required to mount the Fixed Line or the Flail type
trimmer heads.
Engine Operating Speeds
Operate at full throttle while cutting grass.
CAUTION!
Operation at low rpm can lead to premature clutch failure.
Trimming and Mowing Grass
Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut.
To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line.
Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer
head horizontal.
Edging
Tilt the handle about 100° to the left (from horizontal) and move forward,
holding the trimmer or brushcutter vertically as shown.
Tilt the handle about
100° to the left
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
General maintenance
IMPORTANT!
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED
BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A
DEALER OR SERVICE CENTER AUTHORIZED BY ECHO,INC. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PER-
FORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CON-
TROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.
NOTE:
Using non-standard replacement parts could invalidate your Shindaiwa warranty.
WARNING!
WARNING!
Before performing any main-
Non-standard accessories, cut-
tenance, repair, or cleaning work on
ting attachment, or replacement parts
the unit, make sure the engine and
may not operate properly with your unit
cutting attachment are completely
and may cause damage and lead to
stopped. Disconnect the spark plug
personal injury.
wire before performing service or
maintenance.
Muffler
Air Filter
This unit must never be operated with a faulty or miss-
The H4 engine that powers your Shindaiwa model is a hybrid
ing spark arrester or muffler. Make sure the muffler is well
4-stroke engine. As a hybrid, the engine is lubricated by oil
secured and in good condition. A worn or damaged muffler
mixed with the gasoline and air from the carburetor that moves
is a fire hazard and may also cause hearing loss.
through and around the internal parts of the engine in a similar
way that a 2-stroke engine is lubricated. Without the heavy duty
2-stage air filter equipped on all H4 engines, dust and dirt could
also move through the engine, decreasing engine life, increas-
ing valve wear and the need for more frequent valve adjust-
ments. To keep your H4 engine strong and reliable, Shindaiwa
recommends that you check and service the air filter as
instructed in the 10-Hour Maintenance section that follows.
Spark Plug
Keep the spark plug and wire connections tight and clean.
Fasteners
Make sure nuts, bolts, and screws (except carburetor
adjusting screws) are tight.
Daily maintenance
Prior to each work day, perform the
following:
Cooling
fins
■ Remove all dirt and debris from the
Cooling
fins
engine, check the cooling fins and
air cleaner for clogging, and clean
as necessary.
Air
intake
■ Carefully remove any accumula-
tions of dirt or debris from the muf-
fler and fuel tank. Check cooling air
intake area at base of crankcase.
Remove all debris. Dirt build-up
in these areas can lead to engine
overheating, fire, or premature
wear.
Remove all dirt and debris from the engine and check the cooling fins
WARNING!
Always wear gloves when
working around the cutter assembly.
■ Check for loose or missing screws
■ Make sure nuts, bolts, and screws
(except carburetor idle speed
adjusting screws) are tight.
or components. Make sure the cutter
attachment is securely fastened.
■ Clean any debris or dirt from the
cutting attachment.
■ Check the entire unit for leaking fuel
or grease.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
10-Hour maintenance
(more frequently in dusty
conditions)
Loosen
fasteners
1. Remove the air filter cover by loos-
ening the cover screw(s) and lifting.
Prefilter
2. Remove and inspect the pre-filter.
If the pre-filter is torn or otherwise
damaged, replace it with a new
one.
Filter element
3. Clean the pre-filter with soap and
water. Let dry before reinstalling.
4. Inspect the air filter element. If the
element is damaged or distorted,
replace it with a new one.
Components of air filter
Remove the cover of the air filter
5. Tap filter gently on a hard surface to
dislodge debris from element or use
compressed air from the inside to blow
debris out and away from the air filter
element.
IMPORTANT!
Direct the air stream at the inside face
of the filter only!
CAUTION!
Never operate the unit if the air
cleaner assembly is damaged or
missing!
6. Install the air filter element, pre-filter
and cover in the reverse order of
removal.
10/15-Hour maintenance
Remove and clean or replace the
spark plug.
Clean the spark
plug and check
the gap at the
electrode.
■ Clean the spark plug. Adjust elec-
trode gap according to the values
listed in the ”Specifications” section.
If the spark plug must be replaced,
use only the type recommended in
”Specifications” or equivalent resistor
type spark plug of the correct heat
range.
0,6 mm
(0.024 in)
CAUTION!
Before removing the spark plug,
clean the area around the plug to
prevent dirt and debris from getting
into the engine’s internal parts.
Remove and inspect spark plug
50 Hour Maintenance
Gear Housing
A
1. Clean all loose debris from gear box.
2. Remove plug (A) and check level of grease. Grease should fill gear case to
bottom of grease plug hole.
3. Add grease if necessary using manual grease gun or squeeze-type tube. Do
not use high pressure grease gun. DO NOT over-fill.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
50 hour maintenance
Remove and replace the fuel filter
element.
■ Use a hooked wire to extract the
fuel filter from inside the fuel tank.
Inspect the fuel filter element. If
it shows signs of contamination,
replace with a genuine Shindaiwa
replacement fuel filter element.
■ Before reinstalling the new filter ele-
ment, inspect the condition of all the
fuel system components (fuel pick-
up line, fuel return line, tank vent
line, tank vent, fuel cap and fuel
tank).
Hooked wire
■ If damage, splitting or deteriora-
tion is noted, the unit should be
removed from service until it can
be inspected or repaired by a Shin-
daiwa-trained service technician.
Fuel filter element
CAUTION!
Make sure you do not pierce the fuel
line with the end of the hooked wire.
The line is delicate and can be dam-
aged easily.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
135-Hour Maintenance
■ Replace the spark plug annually:
Use only the type recommended in
the ”Specifications” section or an
equivalent resistor type spark plug
of the correct heat range.
■ Combustion chamber should be
decarbonized, and the valve clear-
ance should be adjusted. It is
highly recommended that this is
done by a Shindaiwa-trained ser-
vice technician.
IMPORTANT!
The valve clearance should be adjusted. It is highly recommended that this is
done by a Shindaiwa-trained service technician.
Valve Adjustment
1. Remove cylinder cover, rocker arm
cover, and spark plug. Rotate the
crankshaft while observing the pis-
ton through the spark plug open-
ing. When the piston is at the top of
the compression stroke (TDC), the
valves can be adjusted.
CAUTION!
6. Turn engine over several times, and
returnthe to TDC-compression.
Recheck with proper feeler gauge
to make sure clearance adjust-
ment did not change as a result of
tightening the locknut. Readjust as
necessary.
2. Loosen adjuster locknut so that the
■ Performing a valve adjustment
2.5 mm Allen socket head adjust-
ment screw can turn freely.
incorrectly may cause hard
starting and/or can damage the
engine.
3. Insert 0.10 mm feeler gauge between
valve stem tip and rocker arm.
■ If you are unfamiliar with this
engine or uncomfortable with
this procedure, consult with an
authorized Shindaiwa servicing
dealer.
4. Turn adjustment screw (clockwise =
tighter, counter-clockwise = looser)
until feeler gauge is almost snug.
Back off just enough to allow gauge
to slip out with limited resistance.
7. Replace rocker arm cover gasket
to assure proper sealing and install
cover.
IMPORTANT!
5. While holding the adjustment screw
in place with the Allen driver, tighten
the locknut with a wrench.
If a new gasket is not available and/
or the old gasket is not damaged, the
old gasket may be reused. Never use
cracked or damaged gaskets!
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
Spark Arrester Screen Maintenance
If the engine becomes sluggish and low
on power, check and clean the spark
arrester screen.
Engine Cover
WARNING!
Engine
Cover
Never operate the unit with a
damage or missing muffler or spark
arrester! Operating with a missing or
damaged spark arrester is a fire hazard
and could also damage your hearing.
Screws
1. With a 3 mm hex wrench remove the
engine cover screws and the engine
cover.
Muffler
Muffler Gasket
2. With a 4 mm hex wrench, remove the
3 muffler bolts and the muffler.
3. With a small flat bladed screwdriver
remove the 2 screws holding the
spark arrester screen and cover to the
muffler.
Muffler Bolts
4. Remove the screen and clean it with a
stiff bristle brush.
5. Inspect the cylinder exhaust port for
any carbon buildup.
Spark Arrester Screen
Spark Arrester Cover
6. Reassemble the spark arrester, muf-
fler and engine cover in the reverse
order of disassembly.
Cover Screws
IMPORTANT!
If you note excessive carbon buildup,
consult with an authorized servicing
dealer.
Carburetor Adjustment
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be
made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can
be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to
1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above
1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.
IMPORTANT!
If the engine is adjusted for operation above 1,100 feet ASL, the carburetor
must be re-adjusted when operating the engine below 1,100 feet ASL, oth-
erwise severe engine damage may result.
NOTE:
Every unit is run at the factory and the carburetor is set in compliance with
emission regulations. Carburetor adjustments, other than idle speed, must be
performed by an authorized Shindaiwa dealer..
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
Adjusting Engine Idle
The engine must return to idle speed whenever the throttle lever is released.
Idle speed is adjustable, and must be set low enough to permit the engine
clutch to disengage the cutting attachment.
Idle
Ajust-
ment
Screw
WARNING!
The cutting attachment must NEVER rotate at engine idle! If the
idle speed cannot be adjusted by the procedure described here, return the
unit to your Shindaiwa dealer for inspection.
Idle Speed Adjustment
1. Place the unit on the ground, then start the engine, and then allow it to idle
2-3 minutes until warm.
2. If the attachment rotates when the engine is at idle, reduce the idle speed
by turning the idle adjustment screw counter-clockwise.
3. If a tachometer is available, adjust idle. Check Specifications page for
correct idle speed
1
2
4
Loading Trimmer Line
1. Cut one piece of line to recommended length.
2. Align arrows on top of knob with openings in eyelets.
3. Insert one end of trimmer line into an eyelet, and push
line equal distance through trimmer head.
4. Hold trimmer head while turning knob clockwise to
wind line onto spool until about 5” (13 cm) of each line
remains exposed.
.080 (2.0 mm) dia. - 20’ (6 m)
.095 (2.4 mm) dia. - 14’ (4 m)
.105 (2.7 mm) dia. - 10’ (3 m)
Trimmer head is now fully loaded and ready for
operation.
3
Long Term Storage
Whenever the unit will not be used for 30
days or longer, use the following proce-
dures to prepare it for storage:
■ Remove the spark plug and pour
about 1/4 oz. of engine oil into the
cylinder through the spark plug hole.
Slowly pull the recoil starter 2 or
3 times so oil will evenly coat the
interior of the engine. Reinstall the
spark plug.
CAUTION!
Gasoline stored in the carbure-
tor for extended periods can cause
hard starting, and could also lead to
increased service and maintenance
costs.
■ Clean external parts thoroughly and
apply a light coating of oil to all metal
surfaces.
■ Drain all the fuel from the carburetor
and the fuel tank.
To do so:
IMPORTANT!
All stored fuels should be stabilized with
a fuel stabilizer such as STA-BIL™.
■ Before storing the unit, repair or
replace any worn or damaged parts.
1. Prime the primer bulb until no more
fuel is passing through.
■ Remove the air cleaner element
from the carburetor and clean it thor-
oughly with soap and water. Let dry
and reassemble the element.
NOTE
2. Start and run the engine until it stops
running.
Damage resulting from stale or con-
taminated fuel is not covered by the
Shindaiwa warranty policy.
3. Repeat steps 1 and 2 until the engine
will no longer start.
■ Store the unit in a clean, dust-free
area.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
ENGINE DOES NOT START OR HARD TO START
Remedy
Let cool completely and restart.
Possible Cause
Engine hot/heat soaked.
Low fuel quality.
What To Check
Vaporlock.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Valve adjustment.
Consult with an authorized Shindaiwa
servicing dealer. Adjust valves.
Valve clearance too tight.
Valve clearance too loose.
ENGINE DOES NOT START
What To Check
Possible Cause
Remedy
Consult with an authorized Shindaiwa servicing dealer.
Faulty recoil starter.
Fluid in the crankcase.
Internal damage.
NO
NO
Does the engine crank?
YES
Tighten and re-test.
Loose spark plug.
Good compression?
Consult with an authorized Shindaiwa
servicing dealer.
Excess wear on cylinder,
piston, rings.
YES
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Fuel incorrect, stale, or
contaminated; mixture incorrect.
NO
Does the tank contain fresh
fuel of the proper grade?
YES
Replace fuel filter or vent as required.
Re-start.
Check for clogged fuel filter
and/or vent.
Is fuel visible and moving
in the return line when
priming?
NO
NO
Consult with an authorized Shindaiwa
servicing dealer.
Priming pump not functioning properly.
YES
Move switch to “I” (ON) position
and re-start.
The ignition switch is in
“O” (OFF) position.
Is there spark at the spark
plug wire terminal?
Consult with an authorized Shindaiwa
servicing dealer.
Shorted ignition ground.
Faulty ignition unit.
YES
See "Starting a Flooded Engine"
If the plug is wet, excess
fuel may be in the cylinder.
Check the spark plug.
Clean and gap the spark plug. Check the Specifications
section for the correct plug and gap for your unit. Restart.
The plug is fouled or improperly
gapped.
Replace the spark plug. Check the Specifications section for
the correct plug and gap for your unit. Restart.
The plug is damaged internally
or of the wrong size.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
LOW POWER OUTPUT
Remedy
What To Check
Possible Cause
Operator is overworking the unit.
Use a lower throttle setting.
Is the engine overheating?
Carburetor mixture is too lean.
Improper fuel ratio.
Consult with an authorized Shindaiwa
servicing dealer.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Fan, fan cover, cylinder fins dirty
or damaged.
Clean, repair or replace as necessary.
Carbon deposits on the piston or
in the muffler.
Consult with an authorized Shindaiwa
servicing dealer.
Clogged air cleaner element.
Loose or damaged spark plug.
Service the air cleaner element.
Tighten or replace the spark plug.
Check the Specifications section for the correct plug and gap
for your unit.
Engine is rough at all
speeds. May also have
black smoke and/or
unburned fuel at the
exhaust.
Air leakage or clogged fuel line.
Water in the fuel.
Repair or replace fuel filter and/or
fuel line.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Piston seizure.
Consult with an authorized Shindaiwa servicing dealer.
Faulty carburetor and/or diaphragm.
Overheating condition.
Improper fuel.
Consult with an authorized Shindaiwa
servicing dealer.
Engine is knocking.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Carbon deposits in the
combustion chamber.
Consult with an authorized Shindaiwa
servicing dealer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
ADDITIONAL PROBLEMS
Possible Cause
Clogged air filter.
Remedy
Clean the air filter.
Symptom
Poor acceleration.
Clogged fuel filter.
Lean fuel/air mixture.
Replace the fuel filter.
Consult with an authorized Shindaiwa
servicing dealer.
Idle speed set too low.
Adjust idle. Check Specifications page for correct idle speed.
Ignition switch turned off.
Fuel tank empty.
Reset the switch and re-start.
Engine stops abruptly.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Water in the fuel.
Clogged fuel filter.
Replace fuel filter.
Shorted spark plug or loose terminal.
Clean or replace spark plug. Check the Specifications section
for the correct plug and gap for your unit. Tighten
the terminal.
Ignition failure.
Piston seizure.
Replace the ignition unit.
Consult with an authorized Shindaiwa
servicing dealer.
Ground (stop) wire is disconnected,
or switch is defective.
Test and replace as required.
Engine difficult to shut off.
Overheating due to incorrect spark plug.
Replace the spark plug. Check the Specifications section for
the correct plug and gap for your unit. Restart.
Overheated engine.
Idle engine until cool.
Consult with an authorized Shindaiwa
servicing dealer.
Top of engine is getting
dirty and oily.
Valve cover is leaking.
Adjust idle. Check Specifications page for correct
idle speed.
Consult with an authorized Shindaiwa servicing
dealer.
Idle set too high.
Engine will not idle
down.
Engine has an air leak.
Adjust idle. Check Specifications page for correct idle
speed.
Engine idle too high.
Cutting attachment
moves at engine idle.
Broken clutch spring or worn clutch
spring boss.
Replace spring/shoes as required, check idle speed.
Loose attachment holder.
Inspect and re-tighten holders securely.
Warped or damaged attachment.
Inspect and replace attachment as
required.
Excessive vibration.
Loose gearcase.
Tighten gearcase securely.
Bent main shaft/worn or damaged bushings.
Inspect and replace as necessary.
Inspect and reinstall as required.
Shaft not installed in powerhead or gearcase.
Broken shaft.
Cutting attachment will not
move.
Consult with an authorized Shindaiwa servicing
dealer.
Damaged gearcase.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SHINDAIWA LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO, INC'S RESPONSIBILITY
ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects
in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s
discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods,
limitations and exclusions. THIS LIMITED WARRANTY IS ONLYAPPLICABLE TO SHINDAIWA PRODUCTS SOLD BYAUTHORIZED
SHINDAIWADEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT
OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only
for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance
is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is
separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty
Statement for details regarding emission related parts. For a list of Authorized Shindaiwa Dealers refer to WWW.SHINDAIWA.COM or
call 1-877-986-7783.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment on-line at WWW.SHINDAIWA.
COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage
and provides a direct link if we find it necessary to contact you.
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in
the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your Shindaiwa unit to an authorized
Shindaiwa servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit
after the repairs have been made. For your nearest authorized Shindaiwa servicing dealer, call Shindaiwa’s Dealer Referral Center, at
1-877-986-7783 or you can locate a Shindaiwa servicing dealer at WWW.SHINDAIWA.COM. Should you require assistance or have
questions concerning Shindaiwa’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558
or contact us through the web at WWW.SHINDAIWA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
• 2 YEAR WARRANTY - Units for residential, or non-income producing use will be covered by this limited warranty for two (2) years
from date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cable, and solid drive shaft are warranted for the
life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer
heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a
period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not
covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
COMMERCIAL APPLICATION
•
90 DAY WARRANTY - All Chain Saws and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be
covered by this limited warranty for 90 Days from the date of purchase.
• 2 YEAR WARRANTY - Units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two (2) years from the date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cables, and solid drive shafts are warranted for the
life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer
heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects
in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete,
rocks, or other structures is not covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
RENTAL APPLICATION - 90 DAYS WARRANTY
•
Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of
purchase.
* ECHO INC’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PRODUCT WARRANTy PERIOD
section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final
production.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PURCHASED REPAIR PARTS AND ACCESSORIES
• 90-day all applications
ATTENTION ENGINE POWERED PRODUCT OWNERS
This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD Standard per
ISO/CD 13738 and JASO M345/FD Standards. Shindaiwa Red ArmorTM and Shindaiwa OneTM are a premium engine oil specifically
formulated to meet ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. The use of engine oils designed for other applications,
such as for outboard motors or lawnmowers can result in severe engine damage, and will void your engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
•
Lack of lubrication or engine failure, due to the use of engine oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO
M345/FD Standards. Shindaiwa ONETM Engine Oil meets the ISO-L-EGD and JASO M345/FD Standard. Emission related parts
are covered for 2 years regardless of engine oil used, per the statement listed in the EPA or California Emission Control Warranty
Explanation.
•
Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use
gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/
tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the Shindaiwa oil label and covered
in your operator’s manual.
•
•
Engine damage caused by use of ether or any starting fluids.
Damage caused by tampering with engine speed governor or emission components, or running engines above specified and
recommended engine speeds as listed in your operator’s manual.
•
•
•
Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.
Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.
Defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing,
or use of unauthorized attachments.
•
•
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the
operator's manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized Shindaiwa servicing dealer
during the warranty period.
•
•
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's
Manuals.
•
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark
arrester screen.
•
•
Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.
Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure
to comply with recommended grease or oil change intervals.
•
•
Damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken
strainers.
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational
problem or failure occur, the product should not be used, but delivered as is to an authorized Shindaiwa servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your Shindaiwa
product or by visiting WWW.SHINDAIWA.COM. your receipt of purchase including date, model and serial number must be maintained
and presented to an authorized Shindaiwa servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from
state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR
PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO, INC. and its affiliated
companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended
other than as provided herein. This limited warranty may be modified only by ECHO, INC.
99922201031
02/05/2010
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT
FOR ECHO AND SHINDAIWA BRANDS
The Environmental ProtectionAgency (EPA) and the CaliforniaAir Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased
to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be
designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on
your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/
SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffler, fuel
tank, fuel feed lines, fuel cap assembly, spark plug, air filters, and other associated components. Where a warrantable condition exists, ECHO
Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended
to the original owner including all subsequent owners.
MANUFACTURER'S WARRANTY COVERAGE:
The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part
on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.
OWNER'S WARRANTY RESPONSIBILITIES:
As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO
Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be
aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance
or unapproved modifications.
You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no
Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your
warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986-
7783, web site WWW.SHINDAIWA.COM.
WHAT DOES THIS WARRANTY COVER?
ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions
standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable
requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is
purchased by an end user.
HOW WILL A COVERED PART BE CORRECTED?
If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay
anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In
addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.
WHAT PARTS ARE COVERED?
Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired
or replaced part will be warranted for the remaining ECHO Inc. warranty period.
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.
Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the first scheduled
replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the
first scheduled replacement point for that part.
Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts,
and must be provided without charge if the part is still under warranty.
Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce
the warranty obligations of the manufacturer.
Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts sufficient to meet the expected demand
for such parts.
SPECIFIC EMISSION RELATED WARRANTED PARTS:
• Electronic Ignition System
• Catalytic Converter / Muffler Assembly
• Choke
• Spark Plug
• Carburetor (complete assembly or replaceable components)
• Fuel-Injection Assembly (or replaceable components)
• Fuel Cap Assembly
• Fuel Tank
• Air Filter
• Fuel Feed Line (and associated clamps/connectors as applicable)
WHAT IS NOT COVERED?
Any failure caused by abuse, neglect, improper maintenance, unapproved modifications, use of unapproved add-on parts/modified parts or
unapproved accessories.
99922201033
01/2010
This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing Information
Parts/Serial Number
Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized
Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the
unit with you. You can find these numbers on the engine. For future reference, write them in the space provided
below.
Model No. _____________
SN. ______________
Service
Service of this product during the warranty period must be performed by an Authorized Shindaiwa Service Dealer.
For the name and address of the Authorized Shindaiwa Service Dealer nearest you, ask your retailer or call: 1-877-
986-7783. Dealer information is also available on WWW.SHINDAIWA.COM. When presenting your unit for Warranty
service/repairs, proof of purchase is required.
Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this product you
may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central
Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment by filling out the
warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and pro-
vides a direct link if we find it necessary to contact you.
Additional or Replacement Manuals
Replacement Operator and Parts Catalogs are available from your Shindaiwa dealer or at WWW.SHINDAIWA.
COM or by contacting the Consumer Product Support Department (1-877-986-7783). Always check WWW.SHINDAI-
WA.COM for updated information.
ECHO Incorporated.
400 Oakwood Road
Yamabiko Corporation
7-2 Suehirocho 1-Chome, Ohme,
Tokyo, 198-8760, Japan
Phone: 81-428-32-6118
Fax: 81-428-32-6145
Lake Zurich, IL 60047-1564 U.S.A.
Telephone: 1-877-986-7783
Fax: 1-847-540-8416
Copyright© 2010 By Echo, Incorporated
All Rights Reserved.
T10413001001/T10413999999
Download from Www.Somanuals.com. All Manuals Search And Download.
|