ONE YEAR LIMITED WARRANTY
SI PRODUCTS sells its products with the intent that they are free of defects in manufacture and
workmanship for a period of one year from the date of original purchase, except as noted below.
SI PRODUCTS warrants that its products will be free of defects in material and workmanship under
normal use and service. This warranty extends only to consumers and does not extend to Retailers.
To obtain warranty service on your SI PRODUCTS product, mail the product and your dated sales receipt
(as proof of purchase), postpaid, to the following address:
FLAT PANEL
CERAMIC TOWER HEATER
SI PRODUCTS
Return Center
43155 W. Nine Mile Road Suite 3
Novi, MI 48375
No COD's will be accepted.
SI PRODUCTS does not authorize anyone, including, but not limited to, Retailers, the subsequent
consumer purchaser of the product from a Retailer or remote purchasers, to obligate SI PRODUCTS in any
way beyond the terms set forth herein. This warranty does not cover damage caused by misuse or abuse;
accident; the attachment of any unauthorized accessory; alteration to the product; improper installation;
unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; dropped
product; malfunction or damage of an operating part from failure to provide manufacturer’s recommended
maintenance; transportation damage; theft; neglect; vandalism; or environmental conditions; loss of use
during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other
conditions whatsoever that are beyond the control of SI PRODUCTS.
This warranty is effective only if the product is purchased and operated in the country in which the
product is purchased. A product that requires modifications or adoption to enable it to operate in any
other country than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications is not covered under this warranty.
SI Products
Service Center
1.888.856.6781
8:30a.m. – 7:00p.m. (EST)
M – F
Mail To: SI Products
Return Center
43155 W. Nine Mile Road
Suite 3
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE
SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS OR ANY OTHER OBLIGATION ON THE PART OF THE COMPANY WITH
RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. SI PRODUCTS SHALL HAVE NO LIABILITY FOR
ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY
REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE
DEFECTIVE WITHIN THE EFFECTIVE PERIOD OF THE WARRANTY.
Novi, MI 48375
e-mail:
NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT AVAILABLE,
SI PRODUCTS RESERVES THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU OF REPAIR OR
REPLACEMENT.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed
products, including but not limited to sale of such products on Internet auction sites and/or sales of such
products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and
terminate as to any products or parts thereof which are repaired, replaced, altered, or modified, without
the prior express and written consent of SI PRODUCTS.
This warranty provides you with specific legal rights. You may have additional rights which may vary from
state to state. Because of individual regulations, some of the above limitations and exclusions may not
apply to you. For more information regarding our product line in the USA,
Instruction Manual and
Warranty Information
THE SHARPER IMAGE® name and logo are registered trademarks. Marketed and distributed by
SI Products, LLC under license. ©The Sharper Image. All rights reserved.
EVSI-HTR70
IB-EVSIHTR70
Download from Www.Somanuals.com. All Manuals Search And Download.
• This heater is not intended for use in bathroom, laundry areas and similar moist
indoor locations. Never locate heater where it may fall into a bathtub or other water
container.
SAVE THESE IMPORTANT INSTRUCTIONS
FOR EASY REFERENCE
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or
similar coverings. Do not route cord under furniture or appliances. Arrange cord away
from traffic areas where it can be tripped over.
TECHNICAL SPECIFICATIONS
• To disconnect the heater, first turn controls to the OFF position, then remove plug
from outlet.
Input Voltage
Rated Frequency
Power
120V
60 Hz
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or damage the heater.
1500 Watts
3.62 lbs
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not
Weight
use on soft surface, like a bed, where openings may become blocked.
Noise Level
Unit height
<50dB
• A heater may have hot and arcing sparking parts inside. Do not use it in the areas
where gasoline, paint, or flammable liquids are used or stored.
25.43 inches
85 degrees side to side
CR2032 3V
Oscillation
• Use this heater only for its intended use as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
Remote Control Battery
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension
cord or relocate power tap (outlet/power strip).
CAUTION: Avoid the use of an extension cord because the extension cord
may overheat and cause a risk of fire. However, if you have to use an
extension cord, the cord should be No.14 AWG minimum size and rated not
less than 1875 watts.
• DO NOT use outdoors.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
4
Main Features on the Flat Panel Ceramic Tower Heater
ASSEMBLY INSTRUCTIONS
Insert the bottom of stand pole into the center hole of the base. Lock it into place
by screwing on the nut. Make sure the nut is completely tightened.
5
1
2
6
7
3
4
1. Control Panel
4. Glass Base
2. Grill
5. Handle
3. Stand Pole
6. Back Grill Cover
7. ON/OFF Switch
CAUTION: This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of shock, this plug is intended to fit only
one way in a polarized outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature. To do so could result in
an electric shock hazard.
Touch Screen Control Panel
Timer Setting
Indicator
Heat Setting
Indicator
Stand Pole
HIGH
Oscillation ON
Indicator
Power ON
Indicator
Base
Nut
l
HR
Power
ON/OFF
Oscillation
ON/OFF
Timer Setting Selection
Heat Setting Selection
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6
4. Timer
OPERATING INSTRUCTIONS
There are four possible timer settings: 0.5 hours, 1 (one) hour, 2 (two) hours and
8 (eight) hours. To activate the timer and select a time setting, press TIMER
Turning the Unit On
button on the touch screen. Each time the TIMER
button is pressed, it will
• Check that neither the appliance nor the power cord has been damaged .
switch between settings in a repeating cycle as follows: 0.5 hours, 1 hour, 2
• Place the heater on a firm level surface.
hours,
• Connect the power cord into a standard AC outlet. The heater will beep twice
to confirm the connection.
8 hours, OFF. Press again and the cycle begins again. The selection will light up
on the screen matching the time period. When the timer is OFF, no selections will
be lit.
1. Main switch (on the back side of the device)
• To turn the heater on, flip the main switch to the ON position. When the main
5. Tip-Over Auto Shut Off
switch is flipped to the ON position, the heater will initially be OFF until the
If you tilt the heater at least 40 degrees to the side, you will hear a click sound.
This is the Auto Shut Off safety feature that will power the heater OFF if it is
knocked over. Once the heater is again positioned upright with the base on a firm,
flat surface, the heater will resume power.
ON/OFF
• The heater will beep twice indicating that the heater is ready for use.
• Press ON/OFF button on the touch screen.
• NOTE: Every time a command is pressed on the touch screen, the heater will
emit a small beep and the appropriate symbol will light up confirming the
selection.
button is pressed on the touch screen.
6. Overheat Protection
The heater is equipped with a resettable heat fuse, which is activated and powers
the heater OFF if it overheats. If this occurs, disconnect the heater from the AC
power outlet. As soon as the heater cools down, connect it to the AC power outlet
and you may turn it on again.
2. On/Off and Heat Settings
• Turn the heater ON by pressing the ON/OFF
Every time the heater is turned on it will be operating as follows: LOW heat,
timer OFF, and oscillation OFF.
button on the touch screen.
This heater is also equipped with a non-resettable heat fuse in case first heat fuse
malfunctions. If the non-resettable heat fuse has been activated, operation cannot
be resumed. The heater will need to be repaired by authorized SI product service
personnel.
• Once the heater is ON, press HEAT
HEAT
to return to LOW heat. Either the HIGH or LOW symbol will light up
depending on the heat setting selected.
button to select heat setting. Press
button again
button once to select HIGH heat. Press HEAT
• To turn the heater OFF, simply press ON/OFF
button.
3. Oscillation
• To activate the oscillation, press OSCILLATE
button on the touch screen.
The heater will oscillate 85 degrees side to side. The oscillation symbol
will light up when the heater is oscillating.
• To turn the oscillation off, press OSCILLATE
button. The oscillation
symbol
will no longer be seen on the screen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Using the Remote Control
Cleaning and Storage
Battery Installation
We recommend that the heater be cleaned at least once a month and before
off-season storage.
• Turn the heater OFF at the main switch and unplug it. Allow it to cool.
• Use a dry cloth to clean the external surfaces of the heater.
One CR2032 3V battery is included with the remote control. To activate the remote
control functions, pull out the plastic pull tab protruding from the remote control
housing. To change the battery, remove the battery drawer at the bottom back
of the remote by squeezing the side and pulling the drawer out. Please insert the
battery into the remote with the positive side up as shown on the drawer.
NOTE: Always keep the battery and remote control out of the reach of children.
DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION
• Clean your heater using the above-mentioned steps, then disassemble and
pack the heater in its original container and store it in a cool, dry place.
• The motor is factory lubricated and will require no further lubrication.
+
CR2032
Bottom of Remote
PULL
Air Filter
3V
• Dirt and dust may be caught on the air filter, affecting the function of the device.
Clean the air filter regularly.
PRESS
• To clean, turn unit OFF and unplug unit from outlet, then remove the Back Grill
Cover on the back of the heater. Remove the air filter from the grill.
• Wash the filter by hand in a lukewarm solution of water and detergent. Rinse the
filter in clean water and allow it to dry thoroughly. Place the clean, dry filter back
into the back grill and close the back grill cover.
Remote Control Features
Power ON/OFF
Heat Settings
Timer Settings
• Do not use the device without the filter and back grill cover secure.
Oscillation ON/OFF
Troubleshooting
• Only use CR2032 3V battery with this remote control.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable
(ni-cad, ni-mh, etc) batteries.
• Batteries may pose a choking hazard. Do not let children handle batteries.
• Clean the battery contacts and also those of the device prior to battery installation.
• After opening battery door, be sure the door is properly closed and clicks shut.
• Remove used batteries promptly. Dispose of used batteries immediately.
• If the unit is not going to be used for a long period of time, remove batteries to
prevent damage due to possible battery leakage.
If the Heater Fails to Operate
• Be sure it is plugged in and that the AC outlet is working. Check circuit breaker
in case of a blown circuit.
• Check for any obstruction. If you find an obstruction, press ON/OFF main switch
to turn the heater OFF. Unplug the heater and wait at least ten minutes for it to
cool. Carefully remove the obstruction. Plug the heater back in and restart it as
described under OPERATING INSTRUCTIONS.
• If the heater still does not operate, remove the power cord from the AC outlet
and have the heater service by authorized SI product service personnel.
• Please dispose of used batteries per local regulations.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
|