DATA PROJECTOR
MODEL
PG-LX3000
PG-LX3500
PG-LW3000
PG-LW3500
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
ENGLISH
Introduction
There are two important reasons for prompt warranty registration of your new
SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING:
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
WARNING:
See bottom of projector.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle
is intended to alert the user to the pres-
ence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
WARNING:
void the user's authority to operate this equipment.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is
provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact
1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
fully cool before removing the lamp unit.
• Do not touch the glass surface of the lamp unit or the inside of the projector.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the lamp to become damaged or explode.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Two LR03 batteries
(“AAA” size, UM/SUM-4,
HP-16 or similar)
RGB cable
(6' (1.8 m))
<QCNWGA173WJPZ>
Remote control
<RRMCGB015WJSB>
Power cord*
(1)
(2)
(3)
For U.S. and
Canada, etc.
(6' (1.8 m))
For Europe,
except U.K.
(6' (1.8 m))
For U.K. and
Singapore
(6' (1.8 m))
<QACCDA083WJPZ>
<QACCVA025WJPZ>
<QACCBA105WJPZ>
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
• Initial setup guide <TINS-F649WJZZ>
• CD-ROM <UDSKAA139WJZZ>
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
AN-LX30LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Contents.................................................4
Adjusting the Projected Image
Using
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
•
In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
10. Ventilation
Slots and openings in the cabinet are provided
All the safety and operating instructions
should be read before the product is
operated.
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product
should not be placed in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's
instructions have been adhered to.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
company. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fit into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recommended by the
manufacturer.
This plug will only fit into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
9. Transportation
14. Lightning
A product and cart
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
prevent damage to the product due to
lightning and power-line surges.
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Overloading
19. Replacement Parts
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
When replacement parts are required, be
sure the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the service technician
to perform safety checks to determine that
the product is in proper operating
condition.
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifiers) that produce heat.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualified technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
• DLP® and the DLP logo are registered trademarks of Texas Instruments and
BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
When using the projector in high-
altitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
■ Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
■ Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Caution concerning the setup of the
projector
Warning about placing the projector in
a high position
■ When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
■ For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
Do not block the exhaust and intake
vents.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing difficult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
■ Allow at least 11 13
/16 inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
■ After the projector is purchased, a faint
smell from the vent may appear when the
power is first turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution regarding usage of the projector Temperature monitor function
■ If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
■ If the temperature inside the projector
■ Do not carry the projector by holding the
increases, due to blockage of the air vents,
lens.
or the setting location, the temperature
■ Do not expose the projector to direct
warning indicator will blink. And if the
temperature keeps on rising, “
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Other connected equipment
■ When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
■ Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
Info
• The cooling fan regulates the internal
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation files (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in Zrefer to the main pages in this operation manual where the
topic is explained.
1
2
11
12
3
8
9
4
5
13
14
6
7
10
15 16 17
Top View
Front View
1
2
3
4
Temperature warning indicator
11 Zoom ring
For enlarging/reducing the picture.
Lamp indicator
Power indicator
12 Focus ring
For adjusting the focus.
STANDBY/ON button
13 Intake vent
14 Security bar
15 HEIGHT ADJUST lever
16 Adjustment foot
17 Remote control sensor
For turning the power on and putting the
projector into Standby mode.
5
ENTER button
For setting items selected or adjusted on
the menu.
6
7
VOL (Volume) buttons (–O/Q+)
For adjusting the speaker sound level.
AUTO SYNC button
For automatically adjusting images when
connected to a computer.
8
9
Adjustment buttons (P/R/O/Q)
For selecting menu items.
INPUT buttons (P/R)
For switching Input mode.
10 MENU button
For displaying adjustment and setting
screens.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
9
5
6
7
8
10
11
12
13
14
Rear View (Terminals)
24
LAN terminal
8
9
1
HDMI terminal
Terminal for HDMI input.
Terminal for controlling the projector using
a computer via network.
2
3
AUDIO 2 input terminal
Terminal for controlling the projector using
a computer.
VIDEO input terminal
Terminal for connecting video equipment.
10 Exhaust vent
4
COMPUTER/COMPONENT 1 input
11 Speaker
12 Kensington Security Standard connector
13 Rear adjustment foot
terminal
Terminal for computer RGB and
component signals.
5
6
AUDIO 1 input terminal
22
22, 52
14 AC socket
Connect the supplied power cord.
MONITOR OUT* terminal
(Output terminal for computer RGB and
component signals)
Terminal for connecting a monitor.
COMPUTER/COMPONENT 2* input
Using the Kensington Lock
• This projector has a Kensington Security
Standard connector for use with a
Kensington MicroSaver Security System.
Refer to the information that came with the
system for instructions on how to use it to
secure the projector.
terminal
20, 21
Terminal for computer RGB and
component signals.
* You must switch the setting depending
on whether you are using the terminal for
MONITOR OUT or COMPUTER/
COMPONENT 2 input.
7
AUDIO OUT terminal
22
Audio output terminal of equipment
connected to the audio input terminal.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Numbers in Zrefer to the main pages in this operation manual where the
topic is explained.
8
9
POINTER button
1
2
For displaying the pointer.
Adjustment buttons (P/R/O/Q)
For selecting and adjusting menu items.
13
14
3
4
5
6
7
8
9
10
11
EFFECT button
15
16
17
18
For changing the pointer or spot area.
KEYSTONE button
For entering the Keystone Correction
mode.
12
FUNCTION button
For operating and executing a function
assigned to “FUNCTION Button”.
19
20
21
10
11
13
VOL +/– (Volume) buttons
For adjusting the speaker sound level.
14
INPUT buttons (P/R)
For switching Input mode.
22
12
15
PICTURE MODE button
For selecting the appropriate picture.
16 AUTO SYNC button
For automatically adjusting images when
connected to a computer.
17
18
RESIZE button
1
2
ON button
For switching the picture size (NORMAL,
16:9, etc.).
For turning the power on.
STANDBY button
For putting the projector into the Standby
mode.
MENU button
For displaying adjustment and setting
screens.
3
4
5
6
MAGNIFY buttons
For enlarging/reducing part of the image.
19
20
21
ENTER button
For setting items selected or adjusted on
the menu.
FREEZE button
For freezing images.
RETURN button
For returning to the previous menu screen
during menu operations.
BREAK TIMER button
For displaying the break time.
ECO+QUIET button
For lowering the noise of the cooling fan
and extending the lamp life.
AV MUTE button
For temporarily displaying a black screen
and turning off the sound.
22
3D MODE button
For displaying the 3D MODE menu screen.
7
SPOT button
For displaying the spotlight.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Batteries
Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
1
Insert the batteries.
2
• Insert the batteries making sure the polarities correctly match
the mand nmarks inside the battery compartment.
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
3
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the mand nmarks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then
remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be
reflected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
30°
30°
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
33n (10 m)
• The remote control may malfunction under a
fluorescent lamp. In this case, move the
projector away from the fluorescent lamp.
Remote control signal
transmitters
Remote control
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
8
8 STANDBY button
STANDBY/ON
button
ON button
3
O/Qbuttons
6
INPUT buttons
6
INPUT buttons
6
Zoom ring
Focus ring
5
6
4
4
Adjustment
buttons
(P/R/O/Q)
KEYSTONE button
5
HEIGHT
ADJUST lever
4
1. Place the projector facing a wall or a screen
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than a computer, see pages
3. Turn the projector on
Press STANDBY/ON on the projector or ON on the remote control.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup Guide appears.
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the
Setup Guide.
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
Shrinks
upper side.
Shrinks
lower side.
On the remote control
6. Select the Input mode
Press INPUT P/Rto display the INPUT list. Use INPUT P/Rto select the Input mode,
and use < / > to select the audio input terminal.
On the
projector
On the remote
control
INPUT list
On the
projector
INPUT
Audio
1 COMPUTER1
2 MONITOR OUT
HDMI
On the remote
control
H
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press
the button again while the confirmation message is displayed to put the projector into
Standby mode.
On-screen display
On the
projector
On the remote
control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Video Setup
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture
Indication of the Projection Image Size and Projection Distance
[PG-LW3000/PG-LW3500]
Example: 16:10 Signal Input (Normal Mode)
Picture Size
300" (762 cm)
254"
×
159"
(646 cm
200" (508 cm)
×
404 cm)
170"
(431 cm
×
106"
100" (254 cm)
85"
×
×
269 cm)
53"
(215 cm
×
40" (102 cm)
135 cm)
34"×
(86 cm21"
×
54 cm)
Projection
Distance
4'4"–5'3"
(1.3 m – 1.6 m)
10'11"–13'2"
(3.3 m – 4.0 m)
21'10"–26'4"
(6.7 m – 8.0 m)
32'9"–39'6"
(10.0 m – 12.0 m)
[PG-LX3000/PG-LX3500]
Example: 4:3 Signal Input (Normal Mode)
Picture Size
300" (762 cm)
240"
×
180"
(610 cm
200" (508 cm)
×
457 cm)
160"
×
120"
100" (254 cm)
80"
(406 cm
×
×
305 cm)
60"
(203 cm
×
40" (102 cm)
152 cm)
32"
×
(81 cm 24"
×
61 cm)
Projection
Distance
1.9 m)
6'2"
–
–
15'6"
–
4.7 m)
5'2"
(1.6 m
–
30'11"
–
–
9.4 m)
12'11"
(3.9 m
14.2 m)
46'5"
–
25'10"
(7.9 m
–
38'9"
(11.8 m
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
Screen
Note
H
• Allow a margin of error in the values in the
diagrams below.
Lens center
L
[PG-LW3000/PG-LW3500]
16:10 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
χ
Diag. [ ]
Width
Height
Minimum [L1]
Maximum [L2]
12.0 m (39' 6")
10.0 m (32' 11")
8.0 m (26' 4")
6.0 m (19' 9")
4.8 m (15' 10")
4.0 m (13' 2")
3.2 m (10' 6")
2.4 m (7' 11")
1.6 m (5' 3')
300" (762 cm) 646 cm (254") 404 cm (159") 10.0 m (32' 9")
7 cm (2 37/64")
5 cm (2 9/64")
4 cm (1 23/32")
3 cm (1 9/32")
3 cm (1 1/32")
2 cm (0 55/64")
2 cm (0 11/16")
1 cm (0 33/64")
1 cm (0 11/32")
250" (635 cm) 538 cm (212") 337 cm (132")
200" (508 cm) 431 cm (170") 269 cm (106")
150" (381 cm) 323 cm (127") 202 cm (79")
120" (305 cm) 258 cm (102") 162 cm (64")
8.3 m (27' 4")
6.7 m (21' 10")
5.0 m (16' 5")
4.0 m (13' 1")
3.3 m (10' 11")
2.7 m (8' 9")
2.0 m (6' 7")
1.3 m (4' 4")
100" (254 cm) 215 cm (85")
80" (203 cm) 172 cm (68")
60" (152 cm) 129 cm (51")
135 cm (53")
108 cm (42")
81 cm (32")
54 cm (21")
40" (102 cm)
86 cm (34")
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
χ
Diag. [ ]
Width
Height
Minimum [L1]
Maximum [L2]
300" (762 cm) 610 cm (240") 457 cm (180") 11.3 m (37' 1") 13.6 m (44' 9")
7 cm (2 29/32")
6 cm (2 27/64")
5 cm (1 15/16")
4 cm (1 29/64")
3 cm (1 11/64")
2 cm (0 31/32")
2 cm (0 25/32")
2 cm (0 43/64")
1 cm (0 37/64")
1 cm (0 25/64")
250" (635 cm) 508 cm (200") 381 cm (150")
200" (508 cm) 406 cm (160") 305 cm (120")
150" (381 cm) 305 cm (120") 229 cm (90")
9.4 m (30' 11") 11.4 m (37' 3")
7.5 m (24' 9")
5.7 m (18' 7")
9.1 m (29' 10")
6.8 m (22' 4")
120" (305 cm) 244 cm (96")
100" (254 cm) 203 cm (80")
80" (203 cm) 163 cm (64")
70" (178 cm) 142 cm (56")
60" (152 cm) 122 cm (48")
183 cm (72")
152 cm (60")
122 cm (48")
107 cm (42")
91 cm (36")
61 cm (24")
4.5 m (14' 10") 5.5 m (17' 11")
3.8 m (12' 4")
3.0 m (9' 11")
2.6 m (8' 8")
2.3 m (7' 5")
1.5 m (4' 11")
4.5 m (14' 11")
3.6 m (11' 11")
3.2 m (10' 5")
2.7 m (8' 11")
1.8 m (6' 0")
40" (102 cm)
81 cm (32")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
16:10 Signal
[Feet/inches]
4:3 Signal
[m/cm] [Feet/inches]
[m/cm]
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
0.03328 0.03328 / 0.3048 0.03768 0.03768 / 0.3048
χ
χ
χ
χ
L2: Maximum projection distance (m/ft)
0.04013 0.04013 / 0.3048 0.04543 0.04543 / 0.3048
χ
χ
χ
χ
H: Distance from the lens center to the bottom of the image (cm/in) 0.02178
0.02178 / 2.54
0.02466
0.02466 / 2.54
χ
: Picture diagonal size : 40''-300''
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance (Continued)
Screen
Note
H
• Allow a margin of error in the values in the
Lens center
diagrams below.
L
[PG-LX3000/PG-LX3500]
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Width
300" (762 cm) 610 cm (240") 457 cm (180") 11.8 m (38' 9")
250" (635 cm) 508 cm (200") 381 cm (150")
200" (508 cm) 406 cm (160") 305 cm (120")
150" (381 cm) 305 cm (120") 229 cm (90")
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
χ
Diag. [ ]
Height
Minimum [L1]
Maximum [L2]
14.2 m (46' 5")
11.8 m (38' 8")
9.4 m (30' 11")
7.1 m (23' 3")
5.7 m (18' 7")
4.7 m (15' 6")
3.8 m (12' 5")
3.3 m (10' 10")
2.8 m (9' 3")
17 cm (6 23/32")
14 cm (5 19/32")
11 cm (4 31/64")
9 cm (3 23/64")
7 cm (2 11/16")
6 cm (2 15/64")
5 cm (1 51/64")
4 cm (1 9/16")
3 cm (1 11/32")
2 cm (57/64")
9.9 m (32' 4")
7.9 m (25' 10")
5.9 m (19' 5")
4.7 m (15' 6")
3.9 m (12' 11")
3.2 m (10' 4")
2.8 m (9' 1")
2.4 m (7' 9")
1.6 m (5' 2")
120" (305 cm) 244 cm (96")
100" (254 cm) 203 cm (80")
80" (203 cm) 163 cm (64")
70" (178 cm) 142 cm (56")
60" (152 cm) 122 cm (48")
183 cm (72")
152 cm (60")
122 cm (48")
107 cm (42")
91 cm (36")
61 cm (24")
40" (102 cm)
81 cm (32")
1.9 m (6' 2")
16:9 Signal Input (16:9 Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens
center to the bottom
of the image [H]
Adjustable range of
image position [S]
χ
Diag. [ ]
Width
Height
Minimum [L1] Maximum [L2]
300" (762 cm) 664 cm (261") 374 cm (147") 12.9 m (42' 3") 15.4 m (50' 7")
250" (635 cm) 553 cm (218") 311 cm (123") 10.7 m (35' 3") 12.8 m (42' 2")
200" (508 cm) 443 cm (174") 249 cm (98") 8.6 m (28' 2") 10.3 m (33' 9")
150" (381 cm) 332 cm (131") 187 cm (74") 6.4 m (21' 2") 7.7 m (25' 3")
120" (305 cm) 266 cm (105") 149 cm (59") 5.2 m (16' 11") 6.2 m (20' 3")
100" (254 cm) 221 cm (87") 125 cm (49") 4.3 m (14' 1") 5.1 m (16' 10")
80" (203 cm) 177 cm (70") 100 cm (39") 3.4 m (11' 3") 4.1 m (13' 6")
60" (152 cm) 133 cm (52") 75 cm (29") 2.6 m (8' 5") 3.1 m (10' 1")
40" (102 cm) 89 cm (35") 50 cm (20") 1.7 m (5' 8") 2.1 m (6' 9")
81 cm (31 53/64")
67 cm (26 17/32")
54 cm (21 7/32")
40 cm (15 59/64")
32 cm (12 47/64")
27 cm (10 39/64")
22 cm (8 31/64")
16 cm (6 23/64")
11 cm (4 1/4")
62 cm ( 24 33
52 cm ( 20 27
42 cm ( 16 11
/
/
/
64")
64")
32")
31 cm ( 12 1/4")
25 cm ( 9 13
21 cm ( 8 11
17 cm ( 6 17
12 cm ( 4 29
8 cm ( 3 17
/
/
/
/
/
16")
64")
32")
32")
64")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
16:10 Signal
[Feet/inches]
4:3 Signal
[m/cm] [Feet/inches]
[m/cm]
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
0.03941 0.03941 / 0.3048 0.04294 0.04294 / 0.3048
χ
χ
χ
χ
L2: Maximum projection distance (m/ft)
0.04717 0.04717 / 0.3048 0.05139 0.05139 / 0.3048
χ
χ
χ
χ
H: Distance from the lens center to the bottom of the image (cm/in) 0.05689
0.05689 / 2.54
0.26952
0.26952 / 2.54
χ
χ
S:Adjustable range of image position (cm/in)See page
.
0.20754
0.20754 / 2.54
-
-
χ
: Picture diagonal size : 40''-300''
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-
■ Table mounted, front projection
■ Ceiling mounted, front projection
[Menu item ➞ “Front”]
[Menu item ➞ “Ceiling + Front”]
■ Ceiling mounted, rear projection
(with a translucent screen)
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
[Menu item ➞ “Ceiling + Rear”]
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold
separately).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
• For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Terminal on
connected equipment
Terminal on the
projector
Equipment
Computer
Cable
RGB cable (supplied)
COMPUTER/
COMPONENT 1,2
RGB
output
terminal
HDMI cable (commercially available)
HDMI
HDMI output
terminal
Note
• Depending on specifications of equipment or the DVIóHDMI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to equipment that
has digital output terminal using a DVIóHDMI digital cable.)
• You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use
this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external
• See page 67 “Compatibility Chart” for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specific instructions in
your computer's operation manual to enable your computer's external output port.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment (Continued)
Terminal on
Terminal on the
projector
Equipment
Cable
connected equipment
Video equipment
HDMI cable (commercially available)
HDMI
HDMI output
terminal
3 RCA to mini D-sub 15 pin cable
(commercially available)
COMPUTER/
COMPONENT 1, 2
Component
video output
terminal
Video cable (commercially available)
VIDEO
Video output
terminal
Audio equipment
ø3.5 mm
audio output
terminal
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
AUDIO 1
RCA audio RCA audio cable (commercially available)
output
terminal
AUDIO 2
Cables for a camera or a video game
Audio
output
terminal
HDMI cable (commercially available)
HDMI output
HDMI
terminal
Note
• Depending on specifications of equipment or the DVIóHDMI digital cable, the signal transmission may
not work property. (The HDMI specification does not support all connections to equipment that has
digital output terminal using a DVIóHDMI digital cable.)
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the
digital video signal does not degrade when transmitted, and a high-quality image with a simple
connection can be enjoyed.
• The HDMI terminal does not support the CEC signal.
• You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use
this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal on
connected equipment
Terminal on the
projector
Equipment
Cable
Cables for a camera or a video game/3 RCA to
mini D-sub 15 pin cable (commercially available) COMPONENT 1, 2
COMPUTER/
Camera/Video game
Component
video
output
terminal
RCA adaptor plug
(commercially available)
Cables for a camera or a video game
VIDEO
Video
output
terminal
Monitor
RGB
input
RGB cable (supplied or commercially
available)
MONITOR OUT
terminal
Amplifier
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
ø3.5 mm
audio input
terminal
AUDIO OUT
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
RCA audio
input
terminal
Note
• You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. To use
this terminal as an output terminal, set “COMPUTER2 Select” to “Monitor Output” before connecting
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• RGB signals and Component signals can be output to the monitor.
This projector is able to process the following signals when connected to HDMI
equipment:
• Audio signal: Linear PCM audio
• Sampling frequency: 48kHz/44.1kHz/32kHz
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial
control cable (cross type, commercially available), the computer can be used to control the
projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the
supplied CD-ROM for “RS-232C Specifications and Commands”.
When connecting to a computer using an RS-232C serial control cable
To RS-232C
terminal
To RS-232C
terminal
RS-232C serial control cable
(cross type, commercially available)
Computer
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
RS-232C Terminal: D-sub 9 pin male connector
Pin No. Signal Name
I/O
Reference
Not connected
1
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
Receive Data
Send Data
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
SG
Signal Ground
6
9
RS
CS
Request to Send
Clear to Send
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal
Pin No. Signal
5
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
9
6
Projector
Pin No.
Computer
Pin No.
Note
4
5
6
4
5
6
• Depending on the controlling device used, it may be necessary to
connect Pin 4 and Pin 6 on the controlling device (e.g. computer).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
When connecting to the LAN terminal using a LAN cable
LINK LED (green)
Illuminates when linked.
TX/RX LED (yellow)
Illuminates when transmitting/receiving data.
*
To ensure safety, do not connect the LAN terminal
with any cables that may cause excessive voltage
such as a telephone line.
Hub
or
Computer
To LAN terminal
LAN cable (Category 5 type,
commercially available)
Note
• When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially
available).
• When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially
available).
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
To AC outlet
Power cord
(supplied)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Info
Turning the Projector On
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector
automatically turns on when the power cord
is plugged into the AC outlet or the breaker
• English is the factory default language. If you
want to change the on-screen display to
another language, change the language
Note that the connections to external
equipment and power outlet should be
done before performing the operations
Press STANDBY/ON on the projector
or ON on the remote control.
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projector
is ready to start operation.
Power indicator
Lamp indicator
Note
STANDBY/ON button
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down
abnormally or the lamp should be
replaced.
• When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has been
illuminated. This is normal operation as the
lamp's control circuitry is stabilising the lamp
output characteristics. It should not be
regarded as faulty operation.
• If the projector is put into Standby mode and
immediately turned on again, the lamp may
take some time to start projection.
• When System Lock is set, the keycode input
box appears. To cancel the keycode setting,
input the keycode that you have already set.
STANDBY
button
ON button
On-screen display (confirmation message)
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector
or STANDBY on the remote control,
then press that button again while the
confirmation message is displayed, to
Info
put the projector into Standby mode.
• Direct Power Off function:
You can unplug the power cord from the AC
outlet even if the cooling fan is still running.
• The projector cannot be turned on while cooling.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
About the Setup Guide
ENTER button
Focus ring
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER to exit the Setup Guide
screen.
Note
• The Setup Guide screen automatically
highlights the items in the following order:
1 FOCUS 2 HEIGHT ADJUST
4 ENTER
3 ZOOM
However, you can adjust the focus, height
(angle) or zoom regardless of the highlighted
item.
• If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR-ADJ” -
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
• Using the knob on the focus ring will make the
adjustments easier.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Adjusting the Height
The height of the projector can be
adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is above the projector,
the projection image can be made higher
by adjusting the projector.
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
1
Make small
adjustments.
HEIGHT ADJUST lever
Remove your hands from the
2
HEIGHT ADJUST lever of the
projector after its height has
been finely adjusted.
• The angle of projection is adjustable up to
9 degrees from the surface on which the
projector is placed.
Rear adjustment foot
Use the rear adjustment foot to
make the projector level.
• The projector is adjustable 2 degrees
from the standard position.
3
Info
• Do not apply too much pressure on the
projector when the front adjustment foot
comes out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
3 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Zoom ring
Rotate the zoom ring to enlarge or
shrink the picture size.
• Using the knob on the zoom ring will make the
adjustments easier.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Correcting Trapezoidal
Distortion
Adjustment buttons
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
(P/R/O/Q)
Note
RETURN button
• The Keystone Correction can be adjusted up to
an angle of approximately 40 degrees and the
screen can also be set up to an angle of
KEYSTONE button
approximately 40 degrees (When the Resize
.
On-screen display
(Keystone Correction mode)
Press KEYSTONE to enter the
1
2
KEYSTONE
ADJUST
0
Keystone Correction mode.
END
Shrinks upper side.
(Move the slide bar in the + direction.)
Press P/Qor O/Rto adjust the
Keystone Correction.
Shrinks lower side.
(Move the slide bar in the - direction.)
Note
• To return to the default setting, press
RETURN while the on-screen display of the
Keystone Correction mode is on the screen.
Press KEYSTONE.
3
• The on-screen display of the Keystone
Correction mode will disappear.
Info
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
VOL +/– (Volume)
buttons
Switching the Input Mode
Select the appropriate Input mode for the
connected equipment.
INPUT buttons
Press INPUT P/Rto display the
INPUT list.
AV MUTE button
Use INPUT P/Rto select the Input
mode.
O/Qbuttons
When you select HDMI input, use O/Q
to select the audio input terminal
(HDMI or AUDIO).
Adjusting the Volume
Press VOL +/– on the remote control
or –O/Q+ on the projector to adjust
the volume.
On-screen display
Note
• Pressing VOL–/–Owill lower the volume.
• Pressing VOL+/Q+ will raise the volume.
Displaying the Black Screen
and Turning Off the Sound
Temporarily
Press AV MUTE on the remote control
to temporarily display a black screen
and turn off the sound.
On-screen display
Note
• Pressing AV MUTE again will turn the
projected image back on.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
RESIZE
button
COMPUTER [PG-LW3000/PG-LW3500]
NORMAL
FULL
1280 × 800
—
NATIVE
800 × 600
1024 × 768
1152 × 864
1400 × 1050
1280 × 1024
—
16:9
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1152 × 864)
SXGA+ (1400 × 1050)
SXGA (1280 × 1024)
1280 × 720
4:3 aspect ratio
1068 × 800
1280 × 720
1000 × 800
1280 × 720
1280 × 722
1280 × 720
1280 × 768
1280 × 800
1360 × 768
1360 × 768
1366 × 768
—
Other aspect ratios
1366 × 768
1280 × 768
—
1280 × 720
1280 × 800
Input signal
Computer
Output screen image
FULL NATIVE
Image type
NORMAL
16:9
Resolution XGA and below
*1
*3
Resolution higher than
XGA
4:3 aspect ratio
*1
SXGA (1280 × 1024)
1280 × 720
5:4 aspect ratio
16:9 aspect ratio
16:9 aspect ratio
15:9 aspect ratio
16:10 aspect ratio
—
*2
*1
*1
—*2
1360 × 768
1366 × 768
*1
*1
1280 × 768
1280 × 800
—*2
—*2
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
*3 In case SXGA+ input.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/DTV [PG-LW3000/PG-LW3500]
Input signal
Output screen image
AREA ZOOM V-STRETCH
Video/DTV
Image type
NORMAL
16:9
*1
*1
*1
4:3 aspect ratio
Squeeze
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Letter box
*1
*1
*1
*1
16:9 aspect ratio
16:9 aspect ratio
16:9 aspect ratio
720P, 1035I,
1080I, 1080P
—*2
540P
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
RESIZE
button
COMPUTER [PG-LX3000/PG-LX3500]
Main resolution
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1152 × 864)
UXGA (1600 × 1200)
SXGA (1280 × 1024)
1280 × 720
NORMAL
FULL
NATIVE
800 × 600
—
BORDER
16:9
4:3 aspect ratio
Other aspect ratios
1024 × 768
—
768 × 576
1152 × 864
1600 × 1200
1280 × 1024
1280 × 720
1360 × 768
1366 × 768
1280 × 768
1280 × 800
1024 × 576
968 × 768
1024 × 576
1024 × 578
1024 × 576
1024 × 614
1024 × 640
720 × 576
—
—
—
—
1360 × 768
—
1024 × 768
1366 × 768
—
1280 × 768
960 × 576
922 × 576
1024 × 576
1280 × 800
Input signal
For 4:3 screen
FULL
For 16:9 screen
Computer
Image type
NORMAL
NATIVE
BORDER
16:9
Resolution
lower than
XGA
—*2
XGA
—*2
*1
*1
4:3 aspect ratio
Resolution
higher than
XGA
SXGA (1280 × 1024)
1280 × 720
5:4 aspect ratio
16:9 aspect ratio
*1
—*2
—*2
1360 × 768
1366 × 768
1280 × 768
*1
*1
*1
1280 × 800
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode
32
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/DTV [PG-LX3000/PG-LX3500]
Input signal
For 4:3 screen
AREA ZOOM
For 16:9 screen
BORDER 16:9
Video/DTV
Image type
4:3 aspect ratio
Squeeze
NORMAL
V-STRETCH
*1
*1
*1
*1
*1
*1
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Letter box
720P, 1035I,
1080I, 1080P
*1
16:9 aspect ratio
16:9 aspect ratio
—*2
—*2
*1
540P
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the Remote Control
MAGNIFY buttons
Displaying the Pointer
FREEZE button
PICTURE MODE button
Press POINTER and press P/R/
1
O/Qon the remote control to
AUTO SYNC button
move the pointer.
• Press EFFECT to change the pointer icon
(5 types).
BREAK TIMER button
SPOT button
Star
Finger1
Finger2
Heart
Underline
Adjustment buttons
(P/R/O/Q)
EFFECT button
Press POINTER again.
2
ECO+QUIET button
POINTER button
• The pointer will disappear.
Using the Spot Function
Displaying and Setting the
Break Timer
Press SPOT and press P/R/O/Q
1
on the remote control to move
the spot area.
Press BREAK TIMER.
1
• Press EFFECT to change the spot area
size (3 types).
• The timer starts to count down from 5
minutes.
1/9
1/25
1/8
On-screen display
Press P/R/O/Qto adjust the
2
Press SPOT again.
2
length of the break time.
• The spot area will disappear.
•Increases with Por Q
5 minutes ➞ 6 minutes ➞ 60 minutes
•Shortens with Oor R
4 minutes ➞ 3 minutes ➞1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Switching the Eco+Quiet
Mode
Canceling the break timer display function
Press ECO+QUIET to switch the
Press BREAK TIMER.
Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the power
consumption will decrease, and the lamp life will
extend.
Note
• The Break Timer is not available while the
projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
Note
- Input Search
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Sync
(Auto Sync Adjustment)
Displaying an Enlarged
Portion of an Image
Auto Sync function works when detecting Graphs, tables and other portions of
input signal after the projector turns on.
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
Press AUTO SYNC to manually adjust
with Auto Sync function.
Press
MAGNIFY on the
1
remote control.
Note
• Enlarges the image.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
• Pressing
or reduces the projected image.
or
MAGNIFY enlarges
Note
Press
.
×1 ×2 ×3 ×4
Freezing a Moving Image
Press
.
Press FREEZE.
1
• You can change the location of the
enlarged image using P, R, Oand Q.
• The projected image is frozen.
Press FREEZE again to return to
the moving image from the
currently connected device.
2
Press RETURN on the remote
2
control to cancel the operation.
• The magnification then returns to ×1.
Note
• The selectable magnifications differ
depending on the input signal.
• In the following cases, the image will
return to the normal size (×1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
Selecting the Picture Mode
You can select the appropriate Picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
• When pressing PICTURE MODE, the Picture
mode changes in the following order:
- When the Resize mode is changed.
STANDARD
PRESENTATION
MOVIE GAME sRGB
*
Note
*
“sRGB” is displayed only when RGB signal is input.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
“Quick Start Menu”
“Picture” menu
Main menu
Sub menu
Main menu
Sub menu
Standard
Presentation
Movie
Game
sRGB
Picture
Picture Mode
Quick Start Menu
Input Search Start
Resolution
Contrast
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
Resize
Normal
Full
Bright
Color
Tint
Native
Area Zoom
V-Stretch
Border (PG-LX3000/LX3500)
16:9
Keystone
-80 +80
Sharp
Red
Eco + Quiet [On/Off]
Blue
Language
English
polski
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Magyar
Türkçe
CLR Temp
-1
0
1
2
Tiếng Việt
BrilliantColor™
C.M.S. Setting [On/Off]
C.M.S.
Information
Go To Complete Menu
Film Mode
Auto
Off
DNR
Level 1
Level 2
Level 3
Eco+Quiet [On/Off]
Reset
C.M.S.-Hue
R
Y
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
C.M.S.-Saturation
G
C
C.M.S.-Value
B
M
Reset
Reset
Return
36
Download from Www.Somanuals.com. All Manuals Search And Download.
“Signal adjustment (SIG-ADJ)” menu
“Screen adjustment (SCR-ADJ)” menu
Main menu
SIG-ADJ
Sub menu
Main menu
SCR - ADJ
Sub menu
Resize
Clock
Phase
H-Pos
V-Pos
Reset
-150 +150
-30 +30
-150 +150
-60 +60
Normal
Full
Native
Area Zoom
V-Stretch
Border (PG-LX3000/LX3500)
16:9
Image Shift
-40 ~ +40 (PG-LW3000/LW3500)
-96 ~ +96 (PG-LX3000/LX3500)
Keystone
-80 +80
Resolution
Overscan [On/Off]
Signal Type
Auto
RGB
YPbPr
OSD Display [On/Off]
Dynamic Range
Auto
Standard
Enhanced
Closed Caption
Off
CC1
CC2
Video System
Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
Background
Logo
Blue
None
PAL-60
Setup Guide [On/Off]
Video Setup
0 IRE
7.5 IRE
PRJ Mode
Front
Ceiling + Front
Rear
Signal Info
Ceiling + Rear
Wall Color
Off
Blackboard
Whiteboard
Green
Yellow green
Yellow
Orange
Pink
Purple
Blue
Greenish blue
English
polski
Magyar
Türkçe
Language
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Tiếng Việt
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items (Continued)
“Projector adjustment (PRJ-ADJ1/2)” menu
“Network” menu
Main menu
PRJ-ADJ1
Sub menu
Main menu
Auto Sync [On/Off]
Network
Password [Enable/Disable]
Page
Page
Auto Power Off [On/Off]
DHCP Client [On/Off]
TCP/IP
Auto Restart [On/Off]
Speaker [On/Off]
Page
Reset Network Setting
Restart Network
IP Address
Fan Mode
Normal
High
Page
System Lock
[Enable/Disable]
Page
Keylock [On/Off]
MAC Address
Projector
Main menu
PRJ-ADJ2
Sub menu
Link
Quick Start Menu [On/Off]
COMPUTER2 Select
Input
Monitor Output
FUNCTION Button
Input Search
Audio Mute
Image Shift
Signal Info
STANDBY Mode
Quick Start
Eco
STANDBY Audio Out [On/Off]
DLP® LinkTM [On/Off]
DLP® LinkTM Invert
All Reset
Lamp Timer (Life)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.
Adjustment buttons (P/R/O/Q)
ENTER button
MENU button
MENU button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
Menu Selections (Quick Start Menu)
• This operation can also be performed by using the buttons on the projector.
Example
Press MENU.
1
• The “Quick Start Menu” screen for the
selected Input mode is displayed.
Quick Start Menu
1024×768
Input Search Start
Resolution
Normal
Resize
Press Por Rto select the
2
3
Keystone
Eco+Quiet
Language
Information
0
desired item, then press ENTER.
Off
English
Press P/R/O/Qto adjust the
item selected, then press
ENTER.
Go To Complete Menu…
Info
SEL./ADJ.
ENTER
END
• To display the advanced settings and
adjustments, select “Go To Complete Menu”.
Press ENTER to display the Complete Menu
screen.
• If you do not want to display the Quick Start
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen (Continued)
Quick Start Menu
The following items can be configured on the Quick Start Menu.
Selectable items
Input Search Start
Description
Automatically searches for and switches to the appropriate Input mode.
Pressing an operation button during input searching cancels the search.
Resolution
Resize
Manually change the resolution.
Use this function when the image and screen size do not match with the
Changes the Resize mode.
Use this function to stretch the image vertically or horizontally or when the
Keystone
Eco+Quiet
Corrects the keystone distortion of projected images.
Use this function to correct the trapezoidal distortion of images caused when
When set to “On”, this function reduces the cooling fan noise and power
Language
Displays the input signal, lamp use time, remaining lamp life, etc.
Displays the Complete Menu for advanced settings and adjustments.
Information
Go To Complete Menu
Note
• The setting of Resize mode will be made independently for each Input mode.
• The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture
mode.
Menu Selections (Complete Menu)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press MENU.
Example: “Picture” screen menu for
COMPUTER (RGB) input
1
• The “Quick Start Menu” screen is
displayed.
Menu item
Picture
SIG
SCR
PRJ1
PRJ2
Press Por Rto select “Go To
2
3
Picture Mode
Contrast
Bright
Red
Blue
Standard
Complete Menu”.
0
0
0
0
0
1
Press Qor Oand select
“Picture” to adjust.
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
On
Info
DNR
Eco+Quiet
Reset
Level 2
Off
• When “PRJ-ADJ2” - “Quick Start Menu” is
set to “On”, pressing MENU displays the
Quick Start Menu screen.
SEL./ADJ.
ENTER
END
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Press Por Rand select “Bright”
Picture
SIG
SCR
PRJ1
PRJ2
4
to adjust.
Picture Mode
Contrast
Bright
Red
Blue
Standard
• The selected item is highlighted.
0
0
0
0
0
1
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
On
DNR
Eco+Quiet
Reset
Level 2
Off
SEL./ADJ.
Single ADJ
END
Items to be adjusted
PRJ1
PRJ2
SIG
Pict.
SCR-ADJ
Resize
Normal
To adjust the projected
image while watching it
Image Shift
Keystone
0
0
Press ENTER.
• The selected item (e.g. “Bright”) is
displayed by itself at the bottom of the
screen.
Press ENTER.
• When pressing Por R, the following item
(“Red” after “Bright”) will be displayed.
The item displayed by itself
Picture
Bright
0
Note
SEL./ADJ.
Rtn. Menu
END
• Press ENTER again to return to the
previous screen.
Picture
SIG
SCR
PRJ1
PRJ2
Press Oor Qto adjust the item
5
6
Picture Mode
Contrast
Bright
Standard
selected.
0
1 5
0
0
0
• The adjustment is stored.
Red
Blue
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
1
On
DNR
Eco+Quiet
Reset
Level 2
Off
Press MENU.
• The menu screen will disappear.
SEL./ADJ.
Single ADJ
END
Note
• The MENU button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute/Input Search
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
Q PAGE1
Q PAGE2
Picture
SIG
SCR
PRJ1
PRJ2
Picture
SIG
SCR
PRJ1
PRJ2
1
2
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Standard
Picture Mode
Standard
0
0
0
0
0
0
0
0
1
CLR Temp
3
2
BrilliantColorTM
C.M.S. Setting
C.M.S.
On
4
5
6
7
Film Mode
DNR
Auto
Level 2
Off
Blue
Eco+Quiet
Reset
SEL./ADJ.
ENTER
END
SEL./ADJ.
ENTER
END
Selecting the Picture Mode
1
The default settings of each item when selecting Picture Mode
Selectable
items
Description
CLR Temp
BrilliantColorTM
Eco+Quiet
Off
Standard
For standard image
0
0
1
2
Presentation Brightens portions of image for
more enhanced presentations.
Off
Movie
Game
*sRGB
Gives natural tint to the
projected image.
–1
0
0
1
–
On
Off
Off
Gives sharpness to the
projected image.
For high fidelity reproduction of
images from a computer.
–
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
Note
• *sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColorTM” and “C.M.S.”, when “sRGB” is
selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Image
Adjusting the Colors
2
4
This function adjusts each of the six main
colors that comprise the color wheel, altering
their “Hue”, “Saturation”, or “Value”.
Adjustment
items
Contrast
Obutton
Qbutton
For less
contrast.
For less
brightness.
For less color
intensity.
For making skin For making skin
tones purplish.
For less
sharpness.
For weaker red. For stronger
red.
For weaker
blue.
For more
contrast.
For more
brightness.
For more color
intensity.
Selectable items
Description
Bright
Color*1
Tint*1
C.M.S.-Hue
Sets the hue of the main colors.
C.M.S.-Saturation Sets the saturation of the main
colors
C.M.S.-Value
Sets the brightness of the main
colors.
tones greenish.
For more
sharpness.
Sharp*1
Red*2
Blue*2
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
For stronger
blue.
Return
Returns to the “Picture” menu
screen.
BrilliantColor™*2 *3 For making the For making the
effect weaker.
effect stronger.
Adjusting “Hue”, “Saturation”, or “Value”.
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
1 Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2 Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3 Press Por Rto select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
Note
4 Select the color to be adjusted with Por Rand
adjust it with Oor Q.
• To reset all adjustment items, select “Reset”
and press ENTER.
Example of adjusting the “Hue”
Main colors
R (Red)
Obutton
Qbutton
Closer to magenta Closer to yellow
3 Adjusting the Color
Y (Yellow)
G (Green)
C (Cyan)
B (Blue)
Closer to red
Closer to green
Closer to cyan
Closer to blue
Closer to magenta
Closer to red
Temperature
Closer to yellow
Closer to green
Closer to cyan
Selectable
Description
items
For lower color temperature for
warmer, reddish incandescent-like
images.
M (Magenta) Closer to blue
–1
0
• When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
• When “Value” is selected, the selected color
becomes
1
For higher color temperature for
cooler, bluish, fluorescent-like images.
O: darker. Q: brighter.
• To reset the adjustment values of each color to
the default settings, select “Reset” and press
ENTER.
Note
• Values on “CLR Temp” are only for general
standard purposes.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
(Continued)
Selecting the Film Mode
Eco+Quiet
5
7
This function provides high-quality playback
of images originally projected at 24 fps, such
as movies on DVDs.
Selectable
items
Brightness and Power consumption
On
Off
Approx. 65%
100%
Selectable
Description
items
Auto
Off
Films are detected automatically.
Films are not detected.
Note
• When “Eco+Quiet” is set to “On”, the fan
sound and power consumption are lower than
they are when “Off” is selected. (Projection
brightness decreases as shown in the chart.)
Note
• This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
- 576I
- 1035I (PG-LW3000/LW3500 only)
- 1080I (PG-LW3000/LW3500 only)
With VIDEO input:
- All signals
Reducing Image Noise (DNR)
6
Video digital noise reduction (DNR) provides
high quality images with minimal dot crawl
and cross color noise.
Selectable
Description
items
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Level 3
Note
• This function is not available for some signals.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal Adjustment (“SIG-ADJ” Menu)
Pict.
SIG-ADJ
SCR
PRJ1
PRJ2
Clock
Phase
H-Pos
V-Pos
0
0
0
0
1
Reset
Resolution
Signal Type
Dynamic Range
Video System
Video Setup
2
3
4
5
6
1024 x 768
Auto
Standard
Auto
0 IRE
Signal Info 1024 x 768
48.3 kHz 60.0 Hz
7
H
/
V
SEL./ADJ.
ENTER
END
Adjusting the Computer Image
Signal Type Setting
1
3
If the optimum image cannot be obtained with
This function allows you to select the input
signal type RGB or Component for
COMPUTER/COMPONENT.
Auto Sync adjustment, use the SIG-ADJ function.
Selectable
Description
items
Selectable
Description
items
Clock
Phase
Adjusts vertical noise.
Auto
Input signals are automatically
recognized as RGB or component.
Adjusts horizontal noise (similar to
tracking on your VCR).
RGB
Set when RGB signals are received.
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
YPbPr
Set when Component signals are
received.
Centers the on-screen image by
moving it up or down.
Selecting the Dynamic Range
4
Note
An optimum picture may not be displayed if an
HDMI-capable device’s output signal type and
the projector’s input signal type do not match. If
this should occur, switch “Dynamic Range”.
• To reset all adjustment items, select “Reset”
and press ENTER.
• The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
Selectable
Description
items
Auto
In most circumstances, “Auto” should
be selected.
Resolution Setting
2
Standard
Enhanced
When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.
Ordinarily, the type of input signal is detected and
the correct Resolution mode is automatically
selected. However, for some signals, the optimal
Resolution mode in “Resolution” may need to be
selected to match the computer display mode.
Note
Note
• The Dynamic Range can be selected only
when “HDMI” input mode is selected.
• See “Checking the Input Signal” on page 46
for information on the currently selected input
signal.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal Adjustment (“SIG-ADJ” Menu)
(Continued)
Setting the Video System
Setting the Video Setup
5
6
The video input system mode is factory preset
to “Auto”; however, a clear picture from the
connected audio-visual equipment may not be
received, depending on the Video signal
difference.
Selectable
items
Description
0 IRE
Sets the black level to 0 IRE.
Sets the black level to 7.5 IRE.
7.5 IRE
In that case, switch the Video signal.
Selectable items
Auto
Note
• This function is available for the following
signals.
PAL
With COMPUTER/COMPONENT input:
- 480I
SECAM
*NTSC4.43
NTSC3.58
PAL-M
With VIDEO input:
- NTSC3.58
PAL-N
Checking the Input Signal
7
PAL-60
This function allows you to check the current
input signal information.
* When reproducing NTSC signals in PAL
video equipment.
Note
• The Video signal can only be set in VIDEO
mode.
• When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
Pict.
SIG
SCR-ADJ PRJ1
PRJ2
Resize
Normal
1
2
3
4
5
6
7
8
9
0
Image Shift
Keystone
Overscan
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
0
0
On
On
Off
Logo
On
Front
Off
Wall Color
Language
English
SEL./ADJ.
ENTER
END
Setting the Resize Mode
Keystone Correction
1
3
Use this function to stretch the image
vertically or horizontally or when the edges of
the image cannot be seen.
When the image is projected either from the top
or from the bottom towards the screen at an
angle, the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
Note
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
• For details of the Resize mode, see pages
• You can also press RESIZE on the remote
Qbutton
Obutton
Adjusting the Image
Position
2
You can move the projected image vertically.
Note
• The Keystone Correction can be adjusted up to
an angle of approximately 40 degrees (When
the Resize mode is set to “NORMAL”).
• You can also press KEYSTONE on the
remote control to adjust Keystone Correction.
Obutton
Qbutton
Note
• This function only works in some Resize
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
(Continued)
Setting the Overscan
Closed Caption
4
6
This function allows you to set the overscan area
(display area).
<For Americas only>
Info
Selectable
Description
items
• This function is available for NTSC3.58 signal.
• This function does not work when the Resize
mode is set to “Border”.
• This function is available in the following cases
only:
On
The input area is displayed without the
screen edges.
Off
The whole input area is displayed.
Resize mode
Keystone Correction
-40 − +40
Normal
Area Zoom
V-Stretch
Note
• This function is available for the following
signals.
16:9
-12 − +12
With COMPUTER/COMPONENT or HDMI*
input:
- 480P
- 540P
- 576P
- 720P
• “Closed Caption” is a system which allows
conversations, narration, and sound effects in TV
programs (Limited regions) and home videos to
be viewed as captions on the screen.
- 1035I
- 1080I/1080P
• If noise appears at the screen edges when
“Off” is selected, set the function to “On”.
• Not all programs and videos will offer closed
captioning. Please look for the
symbol to
ensure that captions will be shown.
• Two channels are available: CC1 and CC2.
Selectable
Description
items
Off
—
Setting the On-screen
Display
5
CC1
CC2
Closed Caption mode for CH1 data
Closed Caption mode for CH2 data
Selectable
items
Description
Note
On
Off
All on-screen displays are displayed.
• Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
• If any button is pressed to call up the on-
screen display while viewing a Closed Caption
broadcast, the closed captions will disappear.
VOLUME/AV MUTE/FREEZE/AUTO
SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/Input Search/
Audio Mute/“An invalid button has
been pressed.” are not displayed.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Background
Image
7
Selecting the Wall Color
This function allows you to project the image
to a colored surface or wall without using a
screen.
0
Selectable items
Description
Sharp logo screen
Logo
Blue
Selectable items
Description
Blue screen
—
Off
The Wall Color function is not
activated.
None
Blackboard
Whiteboard
Projects images onto a
blackboard (dark green).
Selecting the Setup Guide
8
Projects images onto a
whiteboard.
Selectable items
Description
Green
Yellow green
Yellow
On
Displaying the Setup Guide
when turning the projector on.
Orange
Pink
Projects images onto a colored
wall.
Off
Not displaying the Setup Guide.
Purple
Blue
Greenish blue
Reversing/Inverting
Projected Images
9
Selecting the On-screen
Display Language
Selectable items
Description
Front
Normal image (Projected from
the front of the screen)
Ceiling + Front
Rear
Inverted image (Projected from
the front of the screen with an
inverted projector)
The projector can switch the on-screen
display language among 18 languages.
English
polski
Magyar
Türkçe
Reversed image (Projected from
the rear of the screen or with a
mirror)
Deutsch
Español
Nederlands
Français
Italiano
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
Tiếng Việt
Svenska
Português
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
Q PRJ-ADJ1
Q PRJ-ADJ2
Pict.
SIG
SCR
PRJ1 PRJ-ADJ2 Net.
Pict.
SIG
SCR PRJ-ADJ1 PRJ2
8
9
0
Quick Start Menu
COMPUTER2 Select
FUNCTION Button
STANDBY Mode
On
1
2
3
4
Auto Sync
On
On
On
On
Monitor Output
Input Search
Quick Start
On
Auto Power Off
Auto Restart
Speaker
STANDBY Audio Out
5
6
7
Fan Mode
System Lock
Keylock
Normal
Disable
Off
DLP® Link TM
DLP® Link TM Invert
All Reset
Off
Lamp Timer(Life)
SEL./ADJ.
[
0] h
ENTER
[
0] min (100%)
ND
SEL./ADJ.
ENTER
END
Auto Sync (Auto Sync
Adjustment)
Auto Restart Function
1
3
Selectable
items
Description
Selectable
items
Description
On
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
On
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Off
Auto Sync adjustment is not
automatically performed.
Off
The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC.
• The Auto Sync adjustment may take some
time to complete, depending on the image of
the computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
Speaker Setting
4
Selectable
items
Description
On
The audio signal is output from the
internal speaker.
Off
The audio signal is not output from the
internal speaker.
Auto Power Off Function
2
Selectable
items
Description
Fan Mode Setting
This function changes the fan rotation speed.
5
On
Off
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter Standby mode.
Selectable
Description
items
The Auto Power Off function will be
disabled.
Normal
High
Suitable for normal environments.
Set when using the projector at
altitudes of approximately 1,500 meters
(4,900 feet) or more.
Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
Standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
System Lock Function
6
This function prevents unauthorized use of the
projector. Once this function is activated,
users must enter the correct keycode each
time the projector is turned on. We suggest
you record the keycode in a safe place
where only authorized users have access.
Note
• You cannot use the following buttons
for keycode: STANDBY/ON, ON,
STANDBY, ENTER, RETURN and
MENU
• System Lock function recognizes
each button on the remote control
or on the projector as an individual
button, even if they share the same
button name. If you used the buttons
on the projector in setting your
keycode, the keycode cannot be
canceled with the remote control.
Info
• If you lose or forget your keycode, contact
your nearest Sharp Authorized Projector
Dealer or Service Center (see page 71). Even
if the product warranty is valid, the keycode
reset will incur a charge.
a
Setting/Changing the Keycode
Select “System Lock”, then press
PRJ - ADJ1
Setting the System Lock
E NTE R or Q.
Old Code
New Code
Reconfirm
* * * *
–
–
–
–
–
–
–
–
Select “Next”, then press E NTE R.
• The screen for entering the keycode
appears.
Enter the same keycode in “Re-
confirm”.
Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
• When setting the keycode for the first time,
press R on the projector for four times.
Note
To cancel the keycode that you have
already set
• Press R on the projector for four times in
steps 4 and 5 above.
When the System Lock is set
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
PRJ - ADJ1
Setting the System Lock
–
–
–
–
–
–
–
–
–
–
–
–
Old Code
New Code
Reconfirm
Note
Input screen for keycode
• If you input a wrong keycode, the cursor returns to
the first point of the “Old Code”.
• The preset keycode is 4 R buttons on the
projector. When you press the R button four
times, the keycode input screen disappears.
– – – –
System Lock
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
(Continued)
Keylock Function
7
Info
Use this function to lock the operation buttons
on the projector.
This function can be set using either the menu
screen or ENTER on the projector.
• Even when Keylock function is set to “On”,
STANDBY/ON on the projector can be used
to turn on and off the power.
• Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in Standby mode, warming up,
changing input signals, operating the Auto
Sync or Input Search function, in Freeze
mode or on the “System Lock” screen during
warming up.
a
Setting with the menu screen
Selectable
items
Description
On
All buttons on the projector, except
STANDBY/ON, are locked.
Off
Turns off the Keylock function.
Selecting the Quick
Start Menu
8
a
Setting with the projector buttons
Locking the Operation Buttons
Selectable items
Description
Hold down ENTER on the
1
On
Pressing MENU displays the
Quick Start Menu screen.
projector for about 5 seconds
while the projector is being
Off
Pressing MENU displays the
Complete Menu screen.
turned on.
• The Keylock function screen is displayed.
PRJ - ADJ1
Use this function to lock the operation buttons
on the projector.
(Except STANDBY/ON button)
COMPUTER2 Select
9
You can also use the MONITOR OUT terminal
as the COMPUTER/COMPONENT 2 terminal.
Select whether to use the terminal as an input
terminal or output terminal.
Note: You can release the keylock by holding
down ENTER on the projector for about 5 seconds.
Return
On
Selectable items
Description
SEL.
ENTER
END
Input
The terminal can be used as an
input terminal (COMPUTER/
COMPONENT 2).
Select “On”, then press ENTER
.
2
The terminal can be used as an
output terminal (MONITOR
OUT).
Monitor Output
On-screen display
Note
• The Keylock function does not affect the
operation with the remote control buttons.
• You cannot use the Keylock function while the
projector is warming up.
• Set this before connecting the external
equipment.
• The setting cannot be changed when Input
mode is “COMPUTER 2”.
Taking the Keylock Off
Hold down ENTER on the projector for about
5 seconds.
On-screen display
52
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® LinkTM
Setting the FUNCTION
Button Operation
You can assign one of the following functions
to the FUNCTION button on the remote con-
trol. The assigned function can be performed
by just pressing FUNCTION.
0
details.
DLP® LinkTM Invert
Selectable items
Description
details.
Input Search
Automatically searches for and
switches to the appropriate Input
mode.
Returning to the Default
Settings
Audio Mute
For temporarily turning off the
sound. Press FUNCTION again
to turn on the sound
This function allows you to initialize the
settings you have made in the projector.
Image Shift
Signal Info
For moving the projected image
Input signal information is displayed.
Note
STANDBY Mode
• The following items or menu cannot be
initialized.
- Resolution
- Language
- Lamp Timer (Life)
- System Lock
- COMPUTER2 Select
Selectable
items
Description
Eco
Power consumption is reduced in
Standby mode.
Quick Start The period of startup time is reduced.
Checking the Lamp
Life Status
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
STANDBY Audio Out
You can set audio output from the AUDIO
OUTPUT terminal of the projector that is in
Standby mode.
Selectable
Description
items
Lamp usage condition
Remaining lamp life
On
The audio signal is output from the
AUDIO OUTPUT terminal in Standby
mode.
“Life”
100%
5%
Operated exclusively
with “Eco+Quiet”
set to “On”
Approx.
5,000 hours 250 hours
Approx.
Off
The audio signal is not output from the
AUDIO OUTPUT terminal in Standby
mode.
Operated exclusively
with “Eco+Quiet”
set to “Off”
Approx.
2,000 hours 100 hours
Approx.
Note
• When “Eco” is selected for “STANDBY Mode”,
“STANDBY Audio Out” is set to “Off” automatically
and you cannot change the setting.
• The HDMI audio will not output from the
AUDIO OUTPUT terminal when the projector
is in Standby mode.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the
usage condition.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector Network Environment (“Network” Menu)
Pict.
SIG
SCR
PRJ1 PRJ2
Disable
Off
Network
Password
1
2
3
4
5
DHCP Client
TCP/IP
Reset Network Setting
Restart Network
IP Address
XXX.XXX.XXX.XXX
MAC Address XX : XX : XX : XX : XX : XX
6
Projector
Link
XX-XXXX
Disconnected
ꢀ
SEL./ADJ.
ENTER
END
Setting a Password
If you do not want others to change the setting
for the “Network” menu, set a password.
1
Enter the password in “Old
Password” using P, R, Qand O,
then press ENTER.
2
a
Setting a Password
Enter the password in “New
Password” using P, R, Qand O,
then press ENTER.
3
4
Select “Password”, then press
1
ENTER or Q.
• The screen for entering the password
appears.
Enter the same password again
in “Reconfirm” using P, R, Qand
O, then press ENTER.
Network
Setting the Password
–
–
–
–
–
–
–
–
–
–
–
–
Old Password
New Password
Reconfirm
Note
• If you do not need the password protection
for the “Network” menu settings anymore,
press ENTER without entering the new
password in steps 3 and 4.
Press Por Rto set the first digit
in “New Password”, then press Q.
2
• To cancel the password settings, press
RETURN.
Enter the remaining 3 digits, then
3
press ENTER.
• To return to the previous digit, press O.
If you forget the password
If you forget the password, perform the
following procedure to delete it, then set a
new password.
Enter the same password in
“Reconfirm”, then press ENTER.
• The status for “Password” changes to
“Enable”.
4
On the projector, press
Note
.
• Once the password is set, you must enter the
password to change the “Network” menu
settings.
Note
• If ENTER is held down for more than 5
seconds, the operation buttons on the
• You cannot use the buttons on the
remote control to delete the password.
a
Changing the Password
Select “Password”, then press
1
ENTER or Q.
• The screen for entering the password
appears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectable items
Description
DHCP Client Setting
Connect the LAN cable before turning the
projector on. If not, the DHCP Client function
does not work.
2
IP Address
Factory default setting:
192.168.150.002
Enter an IP address
appropriate for the network.
Subnet Mask
Gateway
Factory default setting:
255.255.255.000
Set the subnet mask to the
same as that of the computer
and equipment on the
network.
Selectable items
On
Description
Obtains configuration
parameters for TCP/IP network
automatically.
Off
Sets the TCP/IP manually.
Factory default setting:
000. 000. 000. 000
* When not in use, set to “000.
000. 000. 000”.
Select “On” for “DHCP Client”. “Obtaining IP
Address...” appears, then the menu screen
appears. Confirm the parameters of IP
Address, Subnet Mask and Gateway on the
TCP/IP screen.
Note
If the DHCP server is not available, “Could not
obtain IP Address.” appears.
• Confirm the existing network's segment (IP
address group) to avoid setting an IP address
that duplicates the IP addresses of other
network equipment or computers. If
In this case, set the TCP/IP manually. (See the
item 3.)
“192.168.150.002” is not used in a network
with an IP address of “192.168.150.XXX”, you
don't have to change the projector IP address.
• For details about each setting, consult your
network administrator.
TCP/IP Setting
Set the TCP/IP manually.
3
Select “Off” for “DHCP Client”,
1
2
3
then press ENTER.
Returning to Default
Settings (Network)
4
Select “TCP/IP”, then press
ENTER.
This function allows you to initialize the
Network settings you have made in the
projector.
Enter “IP Address” using P, R, Q
and O, then press ENTER.
Note
Network
• If the values for IP Address, Subnet Mask or
Gateway of the projector have been returned
to the default settings, the computer cannot
be connected to the projector depending on
the computer’s network settings.
Setting the TCP/IP
1 9 2 . 1 6 8 . 1 5 0 . 0 0 2
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
IP Address
Subnet Mask
Gateway
Enter “Subnet Mask” using P, R,
4
5
Restart Network Function
Restarts the network function.
Perform this function when the projector
cannot be controlled via the network.
5
Qand O, then press ENTER.
Enter “Gateway” using P, R, Q
and O, then press ENTER.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector Network Environment (“Network” Menu)
(Continued)
Confirming the
Projector Information
6
You can confirm the following items.
Selectable
Description
items
IP Address
The IP address of the projector is
displayed.
MAC Address The MAC address of the projector is
displayed.
Projector
Link
The projector name is displayed.
Displays the network connection
status.
Connected
Connected to the
network.
Disconnected Disconnected from
the network.
Note
• For information on how to change the
projector name, see “SETUP MANUAL”
contained in the supplied CD-ROM.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Stereoscopic 3D Images
Precautions on Viewing Stereoscopic 3D Images
Before viewing stereoscopic 3D images, please read this section carefully.
WARNING
■
Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would
normally view your screen. However, some people may experience discomfort. The following
precautions are recommended to minimize the potential for experiencing visual problems or any
adverse symptoms.
■
■
Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D
viewing.
* Based on the guidelines issued by the 3D Consortium revised December 10, 2008.
Maintain an appropriate distance from the screen. Viewing from too close a distance can strain
your eyes. If you experience eye strain, immediately discontinue viewing.
If you experience any of the following symptoms during viewing:
• nausea, queasiness/dizziness, headache, blurry vision or double vision that lasts longer than few
seconds
Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your
symptoms have completely gone away. If symptoms persist, discontinue use and do not resume
stereoscopic 3D viewing without discussing your symptoms with a physician.
• As you get more comfortable viewing stereoscopic 3D:
• Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the
parallax on some models of equipment.)
• Adjust the projected image to the most comfortable viewing size by zooming.
(Projecting images on the smallest or largest screen size possible may eliminate the stereoscopic
effect and strain your eyes.)
• Use the DLP® Link™ Invert function to properly set the video for your left and right eyes. (For
details on using “DLP® Link™ Invert”, see the section on its operation in this operation manual.)
The following people should limit stereoscopic 3D viewing:
– Children under 6 years of age (to protect the eye growth process)
– People with a history of photosensitivity
– People with heart disease
■
– People in poor health
– People who are sleep deprived
– People who are physically tired
– People under the influence of drugs or alcohol
■
Epilepsy
A small percentage of the population may experience epileptic seizures when viewing certain
types of images that contain flashing patterns of light.
IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY
The following people should consult a physician before viewing stereoscopic 3D images.
– Anyone with a history of epilepsy, or who has a family member with a history of epilepsy
– Children under 6 years of age
– Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by
flashing light effects
SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR
HISTORY OF EPILEPSY
Discontinue use if you experience any of the following symptoms while viewing stereoscopic
3D images.
– Involuntary movements, eye or muscle twitching
– Muscle cramps
– Nausea, dizziness, or queasiness
– Convulsions
– Disorientation, confusion, or loss of awareness of your surroundings
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on the 3D Projection Function
•
To display 3D images, this projector requires:
WHAT YOU WILL NEED
1) Source devices that support the field sequential format
– For details on the supported signals, see the Compatibility Chart in this operation manual.
2) 3D LCD shutter glasses that support the DLP® Link™* system
– Contact your nearest Sharp Authorized Projector Dealer for purchasing details.
* DLP® Link™ is a trademark of Texas Instruments.
•
•
The projected image may become dark when using the 3D projection function (with “DLP® Link™ ”
set to “On”).
When “DLP® Link™” is set to “On”, the following functions may not work fully or may not be
available at all.
– Keystone/Resize/Magnify
•
•
3D formats except for the field sequential method, such as ones used for Blu-ray 3D or DVD
prepackaged media, are not compatible with this projector. (As of November 2012)
If the power of your left and right eyes greatly differs and you primarily use one eye for viewing the
images, the images will not appear in 3D.
In addition, images may be difficult to view in 3D or images may not be able to be viewed in 3D
depending on the individual or the content being displayed.
The stereoscopic effect varies with the individual.
•
3D viewing is possible within the range that the 3D LCD shutter glasses are able to receive light
signals reflected by the screen. However, most 3D images are manufactured to be viewed from
directly in front of the screen, so 3D viewing is recommended directly in front of the screen as
much as possible.
– The range for receiving signals varies depending on the 3D LCD shutter glasses. For details, see
the operation manual of your 3D LCD shutter glasses.
•
3D images may not be able to be played back correctly on your computer.
Appendix
■
How the 3D Projection Function (DLP Link™ ) Works
The 3D projection function of this projector is compatible with the DLP® Link™ system. To watch
3D images, you use a pair of 3D LCD shutter glasses that alternately display the projected images
for the left and right eyes and are synchronized with a control (light) signal.
Shutter glasses
control light signal*
* The control light signal is transmitted from the lens of the projector, reflected by the screen, and
received by the light reception sensor on the 3D LCD shutter glasses. Therefore, the range of 3D
viewing varies depending on the specifications of the 3D LCD shutter glasses (light signal
receiving sensitivity).
For details, see the operation manual of your 3D LCD shutter glasses.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Stereoscopic 3D Images (Continued)
Press 3D MODE on the remote
6
control to display the 3D MODE
Using 3D Viewing Mode
menu.
Info
Use the following procedure to project
3D images.
For operation of the 3D LCD shutter
glasses and the 3D-video playback
equipment, see the corresponding
operation manual.
• If “An invalid button has been pressed.”
is displayed, a 3D-compatible signal is
not being input. Check the output signal
on the playback equipment.
Press Qto set “DLP® Link™” to
“On”.
7
8
ENTER button
O/Qbuttons
Press ENTER to switch the mode
and enable more natural 3D
image viewing.
Warning!
• If the projector, 3D-video playback
equipment, and 3D LCD shutter
3D MODE button
glasses are not properly set, you may
experience eye strain in addition to not
being able to view the images in 3D.
Projecting 3D images
Turn the projector on.
1
Press 3D MODE.
9
• The 3D MODE menu will disappear.
Turn the 3D-video playback
2
equipment on.
• Set the 3D-video playback equipment so
that it outputs one of the signals listed in
the Compatibility Chart in this operation
manual.
Note
• If the images are not displayed in 3D, repeat
steps 6 to 8.
• You can also use “DLP® Link™” and “DLP®
Link™ Invert” on the menu screen to change
the 3D setting.
Switch the Input mode of the
projector to enable input of 3D
video signals.
3
Ending 3D projection
Operate the 3D-video playback
equipment and play back the 3D
content.
Press 3D MODE on the remote
control to display the 3D MODE
menu.
4
1
Press Oto set “DLP® Link™” to
“Off”.
Turn the 3D LCD shutter glasses
on and place them over your eyes.
5
2
Press 3D MODE.
3
• The 3D MODE menu will disappear.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on
the cabinet.
■ Do not use volatile agents such as
insecticides on the projector.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera
lenses) for cleaning the lens. Do not use any
liquid type cleaning agents, as they may
wear off the coating film on the surface of the
lens.
■ As the surface of the lens can easily get
damaged, be careful not to scrape or hit the
lens.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the
plastic may cause damage to the quality or
finish of the projector.
Caution
• Do not use any glass cleaner to clean the lens.
• Avoid touching the lens with your hands to
prevent fingerprints on or damage to the lens
surface.
■ Wipe off dirt gently with a soft flannel cloth.
Using a chemical cloth (wet/dry sheet type
cloth, etc.) may deform the components of
the cabinet or cause cracking.
■ Wiping with a hard cloth or using strong
force may scratch the cabinet surface.
■ When the dirt is hard to remove, soak a cloth
in a mild detergent diluted with water, wring
the cloth well and then wipe the projector.
Strong cleaning detergents may discolor,
warp or damage the coating on the projector.
Make sure to test on a small, inconspicuous
area on the projector before use.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Info
• If you want to clean the air vents during
projector operation, ensure you press
STANDBY/ON on the projector or
Thinner
Wax
STANDBY on the remote control and put the
projector into Standby mode. After the
cooling fan has stopped, clean the vents.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will
illuminate red, and the projector will enter Standby mode. After the projector has entered
Standby mode, follow the procedures given below.
Temperature warning indicator
Lamp indicator
Top View
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning
indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then
the projector will enter Standby mode. When you find the temperature warning indicator
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the
lamp will automatically turn off and then the projector will automatically enter Standby mode.
At this time, the lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the
projector will not turn on.
Indicators on the Projector
Power indicator
Red on
Normal (Standby)
Normal (Power on)
Normal (Cooling)
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be
Green on
Red blinks
Green blinks
Green on
Green blinks
Red on
Lamp indicator
Temperature
warning indicator
Off
Normal
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible Solution
Normal
Abnormal
Temperature
warning
indicator
Off
Red blinks The internal
• Temperatures
around the projector
are high.
• Use the projector in an
area with a temperature of
lower than 95°F (+35ºC).
• Relocate the projector to
an area with proper
(On)/
Red on
temperature is
abnormally high.
(Standby)
• Blocked air intake
• Cooling fan
breakdown
• Internal circuit failure
• Clogged air intake
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
repair.
Lamp
indicator
Green on
(Green
blinks
when the
lamp is
warming
up.)
Red on
Red on
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Remaining lamp life
becomes 5% or less.
• Carefully replace the lamp.
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
repair.
The lamp does
• Burnt-out lamp
• Lamp circuit failure
(Standby) not illuminate.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Power
indicator
Green on/ Red blinks The power
• The lamp unit cover • If the power indicator blinks
Red on
Green
blinks
indicator blinks in
red when the
projector is on.
is open.
in red even when the lamp
unit cover are securely
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
advice.
(Cooling)
Info
• If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace
the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is
controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
■ Purchase a replacement lamp of type AN-LX30LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
U.S.A ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure
can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches
or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition and
the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or
Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause
burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
cool before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the
Lamp Unit
Warning!
• Do not remove the lamp unit from the
projector right after use. The lamp and parts
around the lamp will be very hot and may
cause burns or injury.
Optional
accessory
Lamp unit
AN-LX30LP
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the
steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
STANDBY/ON button
Press STANDBY/ON on the
1
projector or STANDBY on the
remote control to put the
projector into Standby mode.
Disconnect the power cord.
2
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
Remove the lamp unit cover.
3
• Loosen the user service screw (1) that
secures the lamp unit cover. Slide the lamp
unit cover in the direction of the arrow and
then lift it up (2).
User service screw
(for lamp unit cover)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp (Continued)
Remove the lamp unit.
4
Securing
screw
• Loosen the securing screw from the lamp
unit. Hold the lamp unit and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
Insert the new lamp unit.
5
6
• Press the lamp unit firmly into the lamp unit
compartment to align the lamp connectors.
Fasten the securing screw.
Replace the lamp unit cover.
• Slide the lamp unit cover horizontally back
into place and align the tabs (1). Then
tighten the user service screw (2) to
secure the lamp unit cover.
Info
• If the lamp unit and lamp unit cover
are not correctly installed, the power
will not turn on, even if the power
cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or
explode.
Connect the power cord.
1
AC socket
• Plug the power cord into the AC socket of
the projector.
STANDBY/ON
button
Reset the lamp timer.
ENTER button
2
• While simultaneously holding down
MENU, ENTER and Ron the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
MENU button
Rbutton
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatibility Chart
Computer
•
Multiple signal support
Horizontal Frequency: 15-110 kHz,
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-165 MHz
Sync signal: Compatible with TTL level
Compatible with sync on green signal
•
Display
Horizontal frequency
[kHz]
Analog
Digital
PC/MAC
Mode
Resolution
Vertical frequency [Hz]
Support Support
PG-LW3000/PG-LW3500 PG-LX3500/PG-LX3000
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.9
55.0
66.2
67.5
60.0
75.0
64.0
80.0
64.0
65.3
65.3
75.0
34.9
49.7
60.2
60
72
75
85
56
60
72
75
85
60
70
75
85
60
60
60
75
60
60
60
60
70
75
60
75
60
75
60
60
60
60
67
75
75
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
VGA
640 × 480
4
4
4
4
Upscale
SVGA
XGA
800 × 600
1024 × 768
Upscale
4
4
4
TRUE
1280 × 720
1280 × 768
4
4
4
TRUE
PC
WXGA
1280 × 800
1360 × 768
1366 × 768
1440 × 900
4
4
WXGA+
1152 × 864
Intelligent
Compression
SXGA
4
Intelligent
Compression
1280 × 960
1280 × 1024
1400 × 1050
4
4
4
4
SXGA+
WSXGA+
UXGA
VGA
SVGA
XGA
1680 × 1050
1600 × 1200
640 × 480
832 × 624
1024 × 768
MAC 13”
MAC 16”
MAC 19”
Upscale
Upscale
TRUE
Intelligent
Compression
Intelligent
Compression
MAC 21”
SXGA
1152 × 870
68.7
75
4
Note
• Optimum image quality will be achieved by matching your computer's output resolution to the
resolution that corresponds to “TRUE” in the “Display” column shown above.
• When “Screen resolution” of the computer is different from the resolution displayed on the projected
image, follow the procedures shown below.
– Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in
“Screen resolution” of the computer.
–
Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is
recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
3D Supported Signals
Analog
Support
Digital
Support
Signal
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
×
77.1
98.6
92.6
101.6
120
120
120
4
4
4
4
4
4
4
4
SVGA
XGA
800 600
×
1024 768
×
1280 720
2
WXGA *
1
×
120 *
1280 800
*1 Reduced Blanking
*2 PG-LW3500/PG-LW3000 only
Note
• Your computer graphics card must be able to display 3D stereoscopic signals.
Please check with your computer/graphic card specifications or call your computer manufacturer to
ensure this capability.
DTV
Horizontal
Vertical
Analog
Support
Digital
Support
Horizontal
Vertical
Analog
Support
Digital
Support
Signal
Signal
Frequency (kHz) Frequency (Hz)
Frequency (kHz) Frequency (Hz)
15.7
31.5
33.8
15.6
31.3
37.5
45.0
33.8
60
60
60
50
50
50
60
60
4
4
4
4
4
4
4
4
28.1
33.8
27.0
28.1
33.8
56.3
67.5
50
60
24
25
30
50
60
4
4
4
4
4
4
4
4
480I
480P
540P
576I
576P
720P
720P
1035I
1080I
1080I
1080P
1080P
1080P
1080P
1080P
4
4
4
4
4
4
4
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected Input mode is wrong.
–
• The AV Mute function is working.
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
No picture and no sound
or projector does not
start.
• The lamp unit cover is not installed correctly.
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
• Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is switched
to the external output. Refer to the computer's operation manual for
how to switch its signal output settings.
–
• Is “On” selected in “DLP® LinkTM”?
Sound is heard but no
picture appears
(or picture is dark).
• Check that “Wall Color” is configured correctly.
Dark or bluish image
• Image adjustments are incorrectly set.
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the
“BrilliantColorTM” value.
(Video Input only)
• Video input system is incorrectly set.
(COMPUTER/COMPONENT Input only)
• Input signal type (RGB/Component) is incorrectly set.
Color is faded or poor.
• Adjust the focus.
–
• The projection distance exceeds the focus range.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Set up the projector at least
one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
Picture is blurred;
noise appears.
(Computer Input only)
• Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)
• Noise may appear depending on the computer.
–
• Cables are incorrectly connected to the projector.
• Volume is set to minimum.
• When the projector is connected to an external device and the volume
is set to minimum, the sound is not output even if you turn up the
volume of the external device.
• “Speaker” is set to “Off”.
• The Audio Mute function is working.
Picture appears but no
sound is heard.
Data image is not
centered.
• Depending on the computer you are using, the output resolution signal
may be different from the one you have set. For details, refer to the
operation manual of the computer.
–
• If the picture is normal, the sound is due to cabinet shrinkage caused
by room temperature changes. This will not affect operation or
performance.
–
An unusual sound is
occasionally heard from
the cabinet.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Page
• See “Maintenance Indicators”.
Maintenance indicator on
the projector illuminates
or blinks in red.
• Change the input signal type setting.
Picture is green on
COMPUTER (YPbPr)/
HDMI (YPbPr)
Picture is pink
(no green) on
COMPUTER (RGB)/
HDMI (RGB)
• Image adjustments are incorrectly set.
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
faster.
• The lamp indicator is illuminating in red.
Replace the lamp.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
• Cables are incorrectly connected to the projector or the connected
equipment works improperly.
The image sometimes
flickers.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
The lamp needs much
time to turn on.
Picture is dark.
• Operate the remote control while pointing it at the projector's remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the
projector's remote control sensor, place the projector where it will not
be affected by strong light.
The remote control
cannot be used.
• The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
Problem
Check
Page
• Images may appear to flicker when fluorescent light or ambient light
enters your vision.
– Turn off the lights.
–
–
–
3D images flicker when
watching in a room.
– Block any ambient light.
• Check that you are using 3D LCD shutter glasses that support the
Ghosting (a double image)
occurs without the image
appearing in 3D.
DLP® Link™ system.
– Be sure to use 3D LCD shutter glasses that support the DLP® Link™
system.
• Check that the shutters on the 3D LCD shutter glasses are working
properly.
– Turn the 3D LCD shutter glasses off and then on again.
– Check the batteries of the 3D LCD shutter glasses.
– Check that the 3D LCD shutter glasses are set to 3D viewing mode.
Some 3D LCD shutter glasses are equipped with a special viewing
mode (such as “dual view mode”) in addition to the normal 3D
viewing mode. See the operation manual of your 3D LCD shutter
glasses.
• Check the settings of the projector.
–
– Turn the DLP® Link™ function “On”.
– Use “DLP® Link™ Invert” to change the setting.
• Check whether a signal that is not supported is being input.
– Configure your 3D application at the correct resolution and refresh
rate.
Make sure you are running your 3D application in resolutions that
support 3D. To support 3D, your 3D application must be configured
to run at the correct settings for this projector.
For details on the supported signals, see “3D Supported Signals” of
the Compatibility Chart.
• If the projector is connected to a computer for 3D image playback,
check that a stereoscopically-enabled application is being used.
– Use the applicable software.
–
–
– Set the applicable software to the field sequential format.
• Check that there are no obstructions between the screen and the 3D
LCD shutter glasses.
– Remove any obstructions.
Any obstructions may cause the glasses not to function properly
causing the lenses to flicker or turn off. Do not place your hand or
other objects in front of the 3D control signal sensor on the glasses.
• Check whether there is a source of high intensity lighting nearby.
– Block the light or turn it off.
–
–
High intensity lighting can interfere with communication between the
3D LCD shutter glasses and the screen resulting in some flicker.
• Check whether two or more projectors are projecting 3D images at the
same time.
– Use only one projector at a time.
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5
minutes.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
manual does not answer your question, please contact the SHARP Service
departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Denmark
SHARP Electronics (Nordic) AB
(0) 70 230 810
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Austria
SHARP Electronics (Europe) GmbH
0820 - 50 08 20
EUR 0,145/min, Anrufe aus dem
Mobilfunknetz können teurer sein
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
Latin America Sharp Electronics Corp. Latin
American Group
9900-0159 Belgium
(305) 264-2277
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
Germany
Sharp Electronics (Europe) GmbH
01805- 29 95 29
0,14 €/Min. aus dem dt. Festnetz,
Mobilfunkpreis max. 0,42 €/Min.
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111
U.K.
Sharp Electronics (U.K.) Ltd.
08705 274277
Fax: (09) 573-0112
Singapore
Hong Kong
Taiwan
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
France
Spain
SHARP ELECTRONICS FRANCE
Tel: 0820 856 333
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
SHARP ELECTRONICA ESPAÑA, S.A.
902 10 13 88
Sharp Corporation (Taiwan)
0800-025111
Switzerland
SHARP ELECTRONICS (SCHWEIZ)
AG
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Infoline deutsch:
0848 074 277 (Montag bis Freitag von
09:00-18:00 Uhr)
Sharp Middle East Fze
971-4-81-5311
Sharp Infoline français:
0848 274 277 (Lundi jusqu'à vendredi
de 09:00-18:00 heures)
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Sweden
Norway
Finland
SHARP Electronics (Nordic) AB
0200 120 800
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
SHARP Electronics (Nordic) AB
22 07 42 82
India
Sharp Business Systems (India)
Limited
SHARP Electronics (Nordic) AB
(09) 146 1500
www.sharp.fi
(91) 11- 6431313
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
Display devices
Resolution
Lens
(Varifocal Lens)
PG-LW3500 PG-LW3000 PG-LX3500 PG-LX3000
0.65" DLP® Chip ×1
WXGA (1280 × 800)
F 2.5 – 2.7
0.55" DLP® Chip ×1
XGA (1024 × 768)
F number
Zoom
Focus
Manual, x 1.2
Manual
f = 21.8 – 25.6 mm
×1
×2
Input terminals HDMI
Computer/Component
(mini D-sub 15 pin)
Video (RCA)
×1
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
Computer/Component
(mini D-sub 15 pin)
×1
×1 (L/R)
×1
Output
terminals
(Shared with COMPUTER/COMPONENT 2; switchable)
Audio (ø3.5 mm stereo minijack)
LAN (RJ-45)
×1 (variable audio output)
×1
Control and
communication
terminals
RS-232C ( D-sub 9 pin )
×1
Speaker
2 W (Mono)
250 W
AC 100 – 240 V
50/60 Hz
3.1 A
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption
Eco+Quiet
Off
AC 100 V
AC 240 V
AC 100 V
AC 240 V
312 W
306 W
218 W
218 W
Eco+Quiet
On
Power consumption
(STANDBY Mode)
Quick Start AC 100 V
AC 240 V
4.85 W
5.34 W
4.47 W
4.99 W
Eco
AC 100 V
AC 240 V
0.35 W
0.78 W
Operation temperature
Cabinet
41ºF to 95ºF (+5ºC to +35ºC)
Plastic
Dimensions (main body only) [W × H × D]
3/32" × 3 45/64" × 9 21/32"
(307 × 94 × 245 mm)
Weight (approx.)
5.7lbs. (2.6kg) 5.5lbs. (2.5kg) 5.7lbs. (2.6kg) 5.5lbs. (2.5kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may be some deviations from these
values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,024,000
(PG-LW3500/PG-LW3000)/786,432(PG-LX3500/PG-LX3000)pixels (micromirrors). As with
any high technology electronic equipment such as large screen TVs, video systems and
video cameras, there are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
12 3/32 (307)
3 5/32 (80)
13/64
(5)
1 23/32
(43.5)
1 1/4
(31.5)
M4 M4
M4
5 3/32 (129)
4 31/32 (126)
• Screw hole specs: 75 mm × 104 mm
• Depth of mounting holes: 8 mm
• Standard screw: M4 (pitch 0.7 mm)
• Quantity: 3
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|