Sharp Projector 68 409 01 User Manual

Sharp Installation  
Configuration and Connections  
SYSTEM 8/10 Plus  
PROJECTOR COMMUNICATIONS KIT  
ATTENTION!  
PLEASE READ THIS DOCUMENT FOR IMPORTANT  
INSTALLATION INSTRUCTIONS  
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:  
Kit Type: SHARP  
Included Communications Adapter(s):  
Quantity  
Part Number  
26-426-01  
26-467-01  
Description  
ADP, SHARP IR  
ADP, UNV, A”  
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING  
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS  
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS  
INDICATED BY THE “” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL  
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER  
WITH THE CORRECT SETTINGS.  
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND  
SIGNAL CONNECTION INSTRUCTIONS.  
THIS SWITCHER HAS BEEN CONFIGURED FOR: SHARP XG (RS-232)  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter  
SW15 Settings  
Comm  
XG (RS-232)  
XG-E1200U  
0
1
0
0
F
F
9
3
J2 ↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-426-01  
XG-1000/E1100  
XG-NV6/NV2U/NV5  
XG-NV3  
0
2
1
0
0
0
F
F
F
3
9
9
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-426-01  
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
XG-P10XU  
PG-C30XU  
2
2
0
0
F
F
9
9
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
XG-P20XU  
1
0
F
9
J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
System 8/10 Plus to Sharp XG Series Projector Connections (RS-232)  
Use the illustration below as a guide when connecting the System 8/10 Plus to a  
Sharp projector. Refer to Sharp documentation to continue the installation.  
________ Important note! For Sharp projectors which do not allow simultaneous  
connections to S-Video and Composite Video (see last note on previous page),  
please refer to the following diagram where either S-Video or Composite Video  
may be connected, but not both at the same time. For those Sharp projectors  
which will allow you to connect to S-Video and Composite Video sources  
simultaneously - please refer to the inset diagram below.  
Composite  
Video  
or  
S-Video  
Universal  
CommAdapter  
26-467-01  
9-Pin Male  
9-Pin Female  
VIDEO INPUT  
S-VIDEO VIDEO  
VIDEO INPUT  
S-VIDEO VIDEO  
AUDIO INPUT  
PC CONTROL  
MOUSE  
FOR PC98  
WIRED  
REMOTE  
L
R
IN  
1
DO NOT  
CONNECT  
HERE  
COMPUTER  
AUDIO IN  
COMPUTER RGB  
AUDIO OUTPUT  
INPUT  
1
OUTPUT  
VIDEO OUTPUT  
L
R
IN  
2
CONNECT  
HERE  
DC5V OUTPUT  
MAX CURRENT 1A  
INPUT  
2
FILTER  
ON  
R
G
B
H
V
+
-
OFF  
Composite  
Video  
and  
S-Video  
Composite  
Video  
or  
S-Video  
15-Pin  
Male  
RGBHV 5 BNC  
________ When RS-232 control of the projector is used, the projector’s IR remote can be  
used. However, because the projector’s IR remote does not communicate with  
the System 8/10 Plus switcher, the projector and switcher can become out-of-  
sync if the projector’s IR remote is used to change the projector’s input, picture  
mute or power settings. Should this occur, press the power, mute or channel  
buttons on the switcher to allow the projector and switcher to resynchronize.  
________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the  
System 8/10 Plus User’s Manual.  
________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
Sharp XG-1000/E1100 Projector Configuration  
Verify that the System 8/10 PLUS is already configured for the Sharp projector.  
The general setup is explained on page 3-4 and the switch settings for the Sharp  
projector are repeated below.  
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS  
front panel. See bottom of page 3-3. The label on the back of the access cover  
also has the configuration information.  
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS  
to verify that the main power is OFF; also turn the projector power OFF.  
2. Set the switches as follows:  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2  
SW15 Settings  
Comm  
Adapter  
3
4
5
6
7 8 9 10  
Sharp XG  
0
0
F
3
J2  
26-426-01  
4
¯
1
2
3
4
5
6
7
8
9
ON  
10  
SW15 DIP Switch  
RS2  
RS1  
RS3  
RS4  
RS5 RS2 RS1  
_ RS5 is for  
RGB switching  
delay. See  
page 3-4 for  
more  
RS3 RS4  
information.  
Configured For:  
RS-232  
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next  
to “Sharp XG”.  
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.  
Unless this is part of a master/slave system, set #3 and #5 to the up position and  
the others down. See picture to the left.  
Use the illustration on the next page to do the following steps.  
5. Connect the Comm Adapter’s miniphone connector to the “Wired Remote” input  
jack and the power plug to the Aux power port on the rear panel of the projector.  
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the  
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear  
panel of the System 8/10 PLUS. (If you wish to make your own communications  
cable, see page 3-2.)  
______ Secure the screws on all D connectors.  
7. Connect the BNC cables from the System 8/10 PLUS outputs to the Sharp  
projector inputs according to the application requirements.  
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The  
Main Power LED should light. Apply power to the projector.  
9. Return System 8/10 PLUS and projector to normal operation.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
Sharp XG-1000/E1100 Projector Connections  
Use the illustration below when connecting the System 8/10 PLUS to a Sharp XG-  
1000/E1100 projector. Refer to Sharp documentation to continue the installation.  
AUDIO  
VIDEO  
S-VIDEO  
Filter  
R
L
WIRED  
REMOTE  
INPUT  
1
ON  
OFF  
Sharp XG-1000 or E1100 Projector  
ANALOG  
DIGITAL  
INPUT  
2
DC12V  
OUTPUT  
COMPUTER RGB INPUT  
C-SYNC  
B
MAX CURRENT  
200mA  
OUTPUT  
COMPUTER RGB OUTPUT  
-
R
G
+
RGB INPUT  
red  
cable  
15-Pin  
15.75kHz/15.625kHz ANALOG RGB  
AUDIO  
Sharp COM  
Adapter  
26-426-01  
9-Pin  
CC 50'  
15-Pin  
________ If the installation includes looping (master/slave) switchers, see Chapter 5.  
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
Sharp XG-E1200U LCD Projector Configuration  
Verify that the System 8/10 Plus is already configured for the Sharp XG-E1200U  
projector by following the procedure and switch settings below. The general  
setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.  
1. Use a small screwdriver to remove the access cover from the System 8/10 Plus  
front panel. Refer to page 3-3 of the User’s Manual.  
___________ Before changing anything, remove the AC power cord to the System 8/10 Plus  
and also turn the projector’s power OFF.  
2. Set the System 8/10 Plus switches as follows:  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2  
SW15 Settings  
Comm  
Adapter  
3
4
5
6
7 8 9 10  
Sharp XG-E1200U  
0
0
F
3
J2  
26-426-01  
4
¯
1
2
3
4
5
6
7
8
9
ON  
10  
SW15 DIP Switch  
RS2  
RS1  
RS3  
RS4  
RS5 RS2 RS1  
RS3 RS4  
Configured For:  
RS-232  
3. Locate the switcher’s Address DIP switches on the rear panel, lower right.  
Unless this is part of a master/slave system, set #3 and #5 to the up position and  
the others in the down position. See illustration on the left.  
4. Use the illustration on the following page and continue with the steps below.  
5. Connect the BNC cables from the System 8/10 Plus outputs to the projector  
inputs according to the application requirements (RGBS, S-Video or Composite  
Video).  
________ The projector’s RGB BNC input will not accept rates lower than VGA or higher  
than XGA. Please refer to your projector user manual.  
________ Because the projector’s video port will only select S-Video when connected to an  
S-Video source, you should not input S-Video and Composite Video sources  
simultaneously since Composite Video will be ignored.  
6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The  
Main Power LED should light. Apply power to the projector.  
7. Installation is now completed.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
System 8/10 Plus - Sharp XG-E1200U LCD Projector Cable Diagram  
Use the illustration below as a guide when connecting the System 8/10 Plus to a  
Sharp XG-E1200U projector. Refer to Sharp documentation to continue the  
installation.  
To S-Video source or  
BNC-to-S-Video adapter  
(26-353-01, male-to-male)  
See first  
note below  
VIDEO INPUT  
S-VIDEO VIDEO  
AUDIO INPUT  
PC CONTROL  
MOUSE  
FOR PC98  
WIRED  
REMOTE  
L
R
COMPUTER  
AUDIO IN  
COMPUTER RGB  
AUDIO OUTPUT  
INPUT  
1
OUTPUT  
VIDEO OUTPUT  
L
R
DC5V OUTPUT  
MAX CURRENT 1A  
INPUT  
2
FILTER  
ON  
R
G
B
H
V
+
-
OFF  
SHARP COM  
ADAPTER 26-426-01  
Power Plug  
Adapter (26-446-01)  
VIDEO INPUT  
S-VIDEO VIDEO  
To Composite Video source (see last note on previous page)  
________ When the Wired Remote jack is installed, the projector’s IR Receivers are  
disabled. This jack can be installed or removed at any time. Please perform the  
basic projector setup before installing the Wired Remote jack.  
________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the  
System 8/10 Plus User’s Manual.  
________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.  
Configuring the Projector  
Please refer to your Sharp XG-E1200U Operations Manual to set up your  
projector. Also, in order for the System 8/10 Plus to know whether the projector  
is “ON” or “OFF”, the projector’s 5VDC output jack must be set to “LAMP”.  
1. Select MENU.  
2. Select SYSTEM SETUP.  
3. Select DC 5V OUTPUT.  
4. Using the  
buttons on the rear of the Sharp XG-E1200U, select  
LAMP.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
Sharp NV6 Projector Configuration  
Verify that the System 8/10 Plus is already configured for the Sharp NV6  
projector by following the procedure and switch settings below. The general  
setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.  
1. Use a small screwdriver to remove the access cover from the System 8/10 Plus  
front panel. Refer to page 3-3 of the User’s Manual.  
__________ Before changing anything, remove the AC power cord to the System 8/10 Plus  
and also turn the projector’s power OFF.  
2. Set the System 8/10 Plus switches as follows:  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2  
SW15 Settings  
Comm  
Adapter  
3
4
5
6
7 8 9 10  
Sharp NV6  
2
0
F
9
J2  
26-467-01  
4
¯
1
2
3
4
5
6
7
8
9
10  
ON  
SW15 DIP Switch  
RS2  
RS3  
RS5 RS2 RS1  
RS1  
RS3 RS4  
RS4  
Configured For:  
RS-232  
3. Locate the switcher’s Address DIP switches on the rear panel, lower right.  
Unless this is part of a master/slave system, set #3 and #5 to the up position and  
the others in the down position. See illustration on the left.  
4. Use the illustration on the following page and continue with the steps below.  
5. Connect the video cables from the System 8/10 Plus outputs to the projector  
inputs according to the application requirements (RGBS, S-Video or Composite  
Video).  
________ The projector’s RGB BNC input will not accept rates lower than VGA or higher  
than XGA. Please refer to your projector user manual.  
________ Because the projector’s video port will only select S-Video when connected to an  
S-Video source, you should not input S-Video and Composite Video sources  
simultaneously since Composite Video will be ignored.  
6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The  
Main Power LED should light. Apply power to the projector.  
7. Installation is now completed.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
System 8/10 Plus - Sharp NV6 Projector Connections  
Use the illustration below as a guide when connecting the System 8/10 Plus to a  
Sharp NV6 projector. Refer to Sharp documentation to continue the installation.  
________ Important note! When connecting the Switcher’s BNC output to either the  
projector’s BNC or 15-pin input (but not both simultaneously), set the projector’s  
input type selector switch to the appropriate “BNC” or “15-pin” setting.  
________ The Sharp NV6 projector does not allow simultaneous connections to S-Video  
and Composite Video (see last note on previous page), please refer to the  
following diagram where either S-Video or Composite Video may be connected,  
but not both at the same time.  
input type  
selector switch  
Sharp RS-232C cable  
Important note!  
Composite Video and S-video  
output to the projector may not  
be connected simultaneously  
Universal  
CommAdapter  
26-467-01  
9-Pin Female  
9-Pin Male  
CC cable  
Composite  
Video  
or  
S-Video  
15-Pin  
Male  
RGBHV 5 BNC  
________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the  
System 8/10 Plus User’s Manual.  
________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
Sharp NV3 Projector Configuration  
Verify that the System 8/10 Plus is already configured for the Sharp NV3  
projector by following the procedure and switch settings below. The general  
setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.  
1. Use a small screwdriver to remove the access cover from the System 8/10 Plus  
front panel. Refer to page 3-3 of the User’s Manual.  
__________ Before changing anything, remove the AC power cord to the System 8/10 Plus  
and also turn the projector’s power OFF.  
2. Set the System 8/10 Plus switches as follows:  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2  
SW15 Settings  
Comm  
Adapter  
3
4
5
6
7 8 9 10  
Sharp NV3  
1
0
F
9
J2  
26-467-01  
4
¯
1
2
3
4
5
6
7
8
9
10  
ON  
SW15 DIP Switch  
RS2  
RS1  
RS3  
RS5 RS2 RS1  
RS3 RS4  
RS4  
Configured For:  
RS-232  
3. Locate the switcher’s Address DIP switches on the rear panel, lower right.  
Unless this is part of a master/slave system, set #3 and #5 to the up position and  
the others in the down position. See illustration on the left.  
4. Use the illustration on the following page and continue with the steps below.  
5. Connect the video cables from the System 8/10 Plus outputs to the projector  
inputs according to the application requirements (RGBS, S-Video or Composite  
Video). One end of the Universal Comm adapter plugs into the IOIOI port of the  
Sharp PC Control adapter. The Sharp PC Control adapter plugs into the  
projector’s PC Control port 1.  
________ The projector’s RGB BNC input will not accept rates lower than VGA or higher  
than XGA. Please refer to your projector user manual.  
________ Because the projector’s video port will only select S-Video when connected to an  
S-Video source, you should not input S-Video and Composite Video sources  
simultaneously since Composite Video will be ignored.  
6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The  
Main Power LED should light. Apply power to the projector.  
7. Installation is now completed.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sharp Installation  
Configuration and Connections  
System 8/10 Plus - Sharp NV3 Projector Connections  
Use the illustration below as a guide when connecting the System 8/10 Plus to a  
Sharp NV3 projector. Refer to Sharp documentation to continue the installation.  
________ The Sharp NV3 projector does not allow simultaneous connections to S-Video  
and Composite Video (see last note on previous page), please refer to the  
following diagram where either S-Video or Composite Video may be connected,  
but not both at the same time.  
PC Control port 1  
Sharp PC Control adapter  
Universal  
CommAdapter  
26-467-01  
9-Pin Female  
9-Pin Male  
See  
note  
above  
CC cable  
Composite  
Video  
or  
S-Video  
15-Pin  
Male  
RGBHV 5 BNC  
________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the  
System 8/10 Plus User’s Manual.  
________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Two Way Radio EK 3053 U User Manual
Sharp Fax Machine UX 340L User Manual
Sharp Microwave Oven R 210H User Manual
Shure Microphone 57A User Manual
Shure TV Antenna WA503 User Manual
Sony Ericsson Cell Phone Accessories MCA 25 User Manual
Sony Microphone ECM 66B User Manual
Sprint Nextel Bluetooth Headset A640 Sprint PCS Vision User Manual
Subaru Robin Power Products Portable Generator DY30 User Manual
Sunbeam Freezer SBCF5WBX User Manual