MODEL
UX-B800SE
FACSIMILE
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Specifications
Print cartridge yield* **
Replacement cartridge: SHARP UX-C80B
Ink Save mode ON: Approx. 800 letter pages
Ink Save mode OFF: Approx. 480 letter pages
(The initial cartridge has the same yield as the above
replacement cartridge.)
Paper tray capacity
Letter: Approx. 200 sheets (20-lb. copier paper at room
temperature; maximum stack height should not be
higher than the line on the tray)
Legal: 100 sheets
Recommended paper weight: 20-lb. Copy Bond
Recording system
Print resolution
Thermal inkjet
600 × 600 dpi
Effective printing width
Fax to E-mail
8.0" (203 mm) max.
Yes; requires an Internet connection and a router,
switch, or hub to connect the machine. LAN cable
(10Base-T/100Base-TX straight- through cable) must be
purchased separately.
File formats
Tiff (G4), PDF (G4)
Memory capacity**
Modem speed
Approximately 100 average pages
14,400 bps with auto fallback to lower speeds.
Approx. 6 seconds
Transmission time**
Compatibility
ITU-T (CCITT) G3 mode
MR, MH, MMR
Compression scheme
Storable transmission
destinations
Rapid Keys: 36
A, B, C keys: 3 (e-mail only)
Speed Dial numbers: 63
Yes (cannot be used if power fails)
8.2" (208 mm) max.
Telephone function
Effective scanning width
**Based on Sharp Standard Chart at standard resolution, excluding time for protocol signals (i.e.,
ITU-T phase C time only).
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Applicable telephone line Public switched telephone network
Reception modes
AUTO, MANUAL, TEL/FAX
Automatic document
feeder
Letter/A4: 20 sheets max. (20-lb. paper; temperature:
64 - 82°F (18 - 28°C); humidity: 45 - 65% RH)
Legal: 5 sheets max.
Input document size
Scanning Resolution
Automatic feeding:
Width: 5.8" to 8.5" (148 to 216 mm)
Length (20 sheets): 5.5" to 11" (140 to 279 mm)
Length (5 sheets): 5.5" to 14" (140 to 356 mm)
Manual feeding:
Width: 2.75" to 8.5" (70 to 216 mm)
Length: 5.5" to 14" (140 to 356 mm)
Standard: 203 x 98 dpi
Fine: 203 x 196 dpi
Super fine: 203 x 391 dpi
Halftone: 203 x 196 dpi
Halftone (grayscale)
Contrast control
Copy function
64 levels
Automatic/Dark selectable
Single/Multi/Sort (99 copies/page)
LCD display, 20 digits x 2 lines
120 V AC, 60 Hz
Display
Power requirements
Power consumption
Operating temperature
Humidity
Standby: 6.0 W, Maximum: 40 W
60 - 90°F (15 - 32°C)
25 - 80% RH
Dimensions
(without attachments)
Width: 15.0" (380 mm)
Depth: 11.0" (280 mm)
Height: 6.1" (156 mm)
Weight
Approx. 9.7 lbs. (4.4 kg)
(without attachments)
As a part of our policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: This machine is not designed for use on a line which has call waiting, call
forwarding, or certain other special services offered by your telephone company (errors
may occur during transmission and reception of faxes).
This machine is not compatible with digital telephone systems.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this
manual. Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do not
use the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Do not spill any liquids on the machine.
Unplug the machine from the power outlet and telephone jack and consult a qualified
service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine where
people may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the
warranty.
Never insert objects of any kind into slots or openings on the machine. This could
create a risk of fire or electric shock. If an object falls into the machine that you cannot
remove, unplug the machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be
seriously damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily accessible.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
A Look at the Operation Panel
1
2
6
3
4
5
7
8
01
02
03
04
05
06
07
08
09
10
11
FUNCTION
COPY/HELP
STOP
ABC
JKL
TUV
DEF
MNO
WXYZ
RESOLUTION/
12
22
32
13
14
15
16
17
18
19
20
21
RECEPTION MODE
GHI
UP
SPEED DIAL
HOLD
23
24
25
26
27
28
29
30
31
PQRS
Z
A
33/G1
34/G2
35
36
REDIAL
SPEAKER
DEL
B'CAST SECURE DUPLEX
DOWN
18
9
10
11 12 13
14 15 16 17
Note: Affix the Rapid Key labels as shown above.
STOP key: Press to cancel an
operation before it is completed.
Number keys: Use to dial numbers.
8
9
1
SCAN TO E-MAIL key: Press to
send a document to an e-mail
recipient.
2
Group Keys: Multiple fax or e-mail
destinations can be stored in each
key for one-touch selection (p. 36).
Display: This displays messages to
help you operate the machine.
3
4
Rapid Keys / letter keys: A fax
number or e-mail address can be
stored in each of these keys for one-
touch selection (attach the Rapid
Key labels). When entering text, the
keys are used as letter keys.
10
A, B, C keys: An e-mail address
can be stored in each key for one-
touch selection (p. 19).
RESOLUTION/RECEPTION key
When a document is in the feeder,
press to adjust the scanning
press to select the reception mode
5
BROADCAST key: Press to send to
multiple fax or e-mail destinations
(p. 35).
11
SECURE key: Press to use the fax
secure receive function (p. 43).
12
13
FUNCTION key: Press this key
followed by the arrow keys to select
special functions and settings.
6
7
DUPLEX key: Use to scan two-
sided documents for transmission
COPY/HELP key
SPEED DIAL key: Press to select a
fax or e-mail destination stored in a
2-digit Speed Dial number (pp. 19,
27).
When a document is in the feeder,
other time, press to print the Help
List.
14
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOLD key: Press to put a phone
START/MEMORY key: Press after
before dialing to send a fax through
and time display to show the
percentage of memory currently
used.
15
16
17
18
SPEAKER key: Press to listen to
the line and fax tones through the
speaker when faxing (p. 26).
Note: This is not a speakerphone.
It cannot be used for speaking.
Arrow keys: Use to scroll through
and select settings, and to search
Letter keys
Use these keys when the display prompts you to enter a name, e-mail address,
or other text.
1
2
3
4
5
Spanish national characters
Ñ
ñ
á
í
é
ó
DEL
B'CAST SECURE DUPLEX
6
7
SYMBOL key: Press to enter a
symbol (the character appearing on
the right side of each letter key).
Press again to return to normal letter
entry mode.
DEL key: Press to delete the
1
6
character marked by the cursor.
When the cursor is to the right of a
line of text, press to backspace and
clear characters. (The cursor can be
Caps Lock key: Press to enter
upper case letters. Press again to
return to lower case letter entry.
moved by pressing
or
.)
2
To delete all entered characters,
hold down until all characters are
cleared.
3
SHIFT key: Hold down to
temporarily change case.
Spanish national characters:
These can be entered when the
7
4
5
Letter keys: Use to enter letters.
display language is set to Spanish.
To enter the character indicated
inside the key, press the key. To
enter the character indicated above
the key, press the key while holding
down the SHIFT key.
@key, .com key: Press to
conveniently enter “@” and “.com”
when entering an e-mail address.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Installation
Unpacking Checklist
Setup
Remove the packing tape
Document
exit tray
Paper
tray
Received
document
Handset
cord
1 Open the cover (➊) and remove the
tape (➋). (Do not install the print
cartridge yet.)
tray
Handset
2
1
Phone Print
Rapid
labels
Setup
guide
Manual
line
cartridge Key
cord
Points to keep in mind when
setting up
2 Close the cover.
♦Do not place the machine in direct
sunlight.
♦Do not place the machine near
heaters or air conditioners.
♦Keep dust away from the machine.
Connect the handset
♦Keep the area around the machine
clear.
About condensation
If the machine is moved from a cold to a
warm place, condensation may form on
the scanning glass, preventing proper
document scanning. To remove the
condensation, turn on the power and
wait approximately two hours before
using the machine.
Attach the trays
Attach the received
document tray
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Paper
2 Pull the paper plate forward and
insert the stack of paper into the
tray, print side up.
Attach the paper tray
Attach the
document exit tray
and flip out the
extension
The stack must
not be higher
than this line
Pull the received document
tray extension all the way out
• If paper remains in the tray, take it
out and combine it into a single stack
with the new paper.
Loading Paper
• Printing on the reverse side of the
Letter or legal size paper can be
loaded.
paper may result in poor print quality.
• Do not use paper that has already
been printed on or is curled.
Maximum number of sheets
(20-Ib. copy bond paper at room
temperature)
• Remove received faxes and other
printed output before about 50
sheets (10 legal-size sheets)
accumulate in the received
document tray (otherwise the sheets
may scatter).
Letter: Approx. 200 sheets
(maximum stack height should not be
higher than the line on the tray)
Legal size: 100 sheets
1 Fan the paper, and then tap the
edges against a flat surface to even
the stack.
If you loaded legal size paper...
You must change the “PAPER SIZE”
(Before changing the setting, plug in
the power cord and install a print
cartridge as explained in the following
sections.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cord
Installing the Print Cartridge
If at any time the display shows [ADD
PAPER &] / [PRESS START KEY],
check the paper tray. If the tray is
empty, add paper. If there is paper in
the tray, take it out and then reinsert it.
Print cartridge yield
SHARP UX-C80B replacement
cartridge
Ink Save mode OFF:
When finished, press
.
Approx. 480 letter pages
Ink Save mode ON:
Approx. 800 letter pages
(The initial cartridge has the same
yield as the replacement cartridge.)
Connecting the Power Cord
Plug the power cord into a 120 V, 60 Hz,
grounded AC (3-prong) outlet.
♦ Ink Save mode is initially turned off.
To turn on Ink Save mode, see
Caution! Do not plug the power cord
into any other kind of outlet. This will
damage the machine and is not
covered under the warranty.
Caution! Do not open the cover while
the machine is printing.
Caution! Remove all packing tape
before plugging in the power cord
machine may result.
Note: Keep print cartridges sealed in
their packages until you are ready to
install them. It is recommended that you
do not use a cartridge that has been left
unused for a long time after opening, as
the print quality may be considerably
degraded.
♦Make sure the machine’s power cord
is plugged in and paper is loaded in
the paper tray.
1 Open the cover (grasp the finger
grip).
The display will show [CHECK
CARTRIDGE] until you install the print
cartridge.
♦ It is recommended that you install
surge protectors for the power and
telephone lines. Surge protectors can
be purchased at most telephone
specialty stores.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
4 Insert the new print cartridge (➊).
Close the holder (➋), making sure it
clicks into place.
If the display shows [PRINTER ERROR]
or [PRINTER ERROR/CHECK PAPER],
open the cover and check for jammed
paper. Remove any jammed paper (see
2
1
2 Remove only the
tape from the new
cartridge.
• Make sure all
tape is removed.
• CAUTION!
DO NOT touch
the gold
contact area
on the
5 Close the cover, pressing firmly on
both front corners.
cartridge.
3 Make sure the cartridge holder is in
the position shown. Place your
fingers on top of the holder and
open the holder release.
Display: [CHANGE CARTRIDGE]/
[1=NEW, 2=OLD].
6 Press
(NEW) if the cartridge
you installed is new.
Display: [NEW CARTRIDGE?] /
[OK:PRESS START]
Press
(OLD) if the cartridge
you installed is old.
• CAUTION! DO NOT touch the gold
contact area or pull on the cable.
7 Press
.
• If you are replacing the cartridge,
remove the old cartridge. If you are
going to use the old cartridge again,
place it in an air-tight container
(containers for this purpose can be
purchased at most office supply
stores).
If you selected "OLD" in the
previous step, this completes the
installation procedure. (Note: If you
find that print quality is not
print cartridge.)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Phone Line
Connecting the Phone Line
If you selected "NEW", the machine
will print an alignment page.
Continue with the steps below.
TEL. LINE
jack
8 In the alignment page, locate the
line that is closest to a straight line.
Standard (RJ-11C) wall jack
The machine is initially set for tone
dialing. If you are on a pulse dial line,
change the “DIAL MODE” setting (pp.
In this example, “15” is
closest to a straight line.
9 Enter the number of the straightest
line with the number keys.
To change the language used in the
display, reports, and lists, change the
“LANGUAGE SELECTION” setting as
• To clear a mistake, press
.
10 Press
.
Name and Fax Number
The machine is initially set to print
high quality images, which require
more ink. If you prefer to use less ink
and speed up drying time, change the
“INK SAVE MODE” setting to “ON”
Enter your name and fax number.
♦Your entered name and fax number
will be printed automatically at the top
of all fax pages you send. (This is
required by FCC regulations.)
When the resolution is set to HALF
TONE, the machine is initially set to
print at a slower printing speed to
enable higher quality images. When
using HALF TONE, if you prefer faster
printing at the expense of slightly
reduced image quality, change the
“QUALITY MODE” setting to “NO” (pp.
1 Press FUNCTION , then
until
[ENTRY MODE] appears.
2 Press
.
Display: [OWN NUMBER SET]
3 Press
.
[ENTER FAX #]
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
1 Press FUNCTION , then
until
until
4 Enter your fax number with the
number keys (max. 20 digits).
[ENTRY MODE] appears.
• To insert a space, press
.
2 Press
, then
• To clear a mistake, press
.
[DATE&TIME SET] appears.
5 Press
.
3 Press
.
6 Enter your name using the letter
keys (max. 24 characters).
Example: SHARP
• The currently set date appears
(example): [DATE 08-15-2006]
4 Enter a two-digit number for the
month ("01" for January, "02" for
February, "12" for December, etc.).
• To clear a mistake, press
.
Example: January
[DATE 01-15-2006]
• For information on using the text
• To correct a mistake, press
move the cursor back to the mistake
and enter the correct number.
to
7 Press
.
[DATE&TIME SET]
STOP
8 Press
to exit.
5 Enter a two-digit number for the day
("01" to "31").
Example: the 5th
[DATE 01-05-2006]
Setting the Date and Time
6 Enter the year (4 digits).
Example:
Set the date and time.
• The currently set time appears
♦The date and time will be printed
automatically at the top of all fax
pages you send (this is required by
FCC regulations). The date and time
also appear in the display.
(example): [TIME 12:19 PM]
7 Enter a two-digit number for the
hour ("01" to "12") and a two-digit
number for the minute ("00" to "59").
♦To have the clock automatically move
forward and backward at the
beginning and end of daylight-saving
time, turn on the “DAY LIGHT
this before you set the date and time.
Example 9:25:
[TIME 09:25 PM]
8 Press
to select A.M. or
to select P.M.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Reception Mode
Volume Adjustment
9 Press
.
[ANTI JUNK #]
STOP
Speaker volume
10 Press
to exit.
SPEAKER
1 Press
.
Setting the Reception Mode
2 Press
or
to select
HIGH, MIDDLE, or LOW.
The machine has three modes for
receiving incoming faxes:
SPEAKER
• Press
again to turn off the
speaker.
AUTO mode:
The machine automatically answers all
calls on 4 rings and begins fax
reception.
Handset receiver volume
1 When talking through the handset,
MANUAL mode:
All calls, including faxes, must be
answered by picking up the
machine's handset or an extension
phone connected to the same line.
press
or
to select HIGH,
MIDDLE, or LOW.
• Note: The volume reverts to
MIDDLE each time you replace the
handset.
TEL/FAX mode:
The machine automatically answers all
calls on 2 rings. If the machine detects
that a call is a voice call (including a
manually dialed fax), it makes a special
ringing sound to alert you to answer. If
the machine detects that the call is an
automatically dialed fax, it begins
reception automatically.
Ringer volume
1 Press
or
to select
HIGH, MIDDLE, LOW, or OFF.
SPEAKER
(Make sure
has not been
To set the reception mode, make sure a
document is not loaded in the
document feeder, and then press
pressed, the handset is not lifted,
and a document is not loaded in the
feeder.)
RESOLUTION/
RECEPTION MODE
until the desired mode
• The ringer will ring once at the
appears in the display.
selected level.
For more information on receiving
faxes, see Chapter 4.
2 If you selected “OFF OK ?” to turn
off the ringer, press
.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.FaxtoE-mail
The Fax to E-mail feature lets you scan
a document and directly send the image
to an e-mail recipient.
Connecting the Machine
The machine is connected using an
Ethernet cable (not included). Please
purchase a 10Base-T/100Base-TX
straight-through (regular) cable.
♦This saves you the trouble of scanning
the document into a computer and
sending the scanned file using an e-
mail program.
Connect one end of the cable to the
LAN port on the machine.
♦The scanned document is sent as an
attachment to an e-mail message.
The attached file can be in TIFF or
PDF format.
Requirements
To use Fax to E-mail, you must
♦Have a broadband (cable or DSL)
Internet connection.
♦Have a broadband router or LAN
switch/hub through which you can
connect the machine to the Internet
(the router is usually connected to a
cable modem or DSL modem).
Connect the other end to a LAN port on
your router, switch, or hub.
♦If you are uncertain which port to
connect the cable to, see the manual
for the router, switch or hub.
A typical setup is shown below.
♦The connections can be made with all
devices powered on.
WAN port
♦For other questions about how the
machine should be connected,
consult your Internet service provider.
Internet
LAN cable
LAN cable
LAN cable
Cable/DSL
modem
LAN ports
(Hub/Switch)
LAN cable
Router
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Machine
IP address
3 Press
.
The machine requires an IP address to
communicate on the Internet.
• If the machine has automatically
received an IP address and is able
to communicate, [IP ADDRESS/
DHCP: ON] will appear on the top
line of the display, followed by the IP
address on the bottom line. To show
the machine’s host name, press
If your network is set up to
automatically assign IP addresses, you
do not need to do anything; the
machine will automatically receive an
IP address when it is connected.
.
Automatic assignment of IP addresses
is normally performed by a DHCP
server, which may be a computer,
router, or other device on the network.
(Most routers used on home networks
contain a DHCP server.)
• If a static IP address has been
entered in the machine and the
machine is able to communicate,
[IP ADDRESS/DHCP: OFF] will
appear on the top line of the display,
followed by the IP address on the
bottom line. To show the machine’s
If your network requires that a static
(permanent) IP address be assigned to
the machine, see Network Settings on
related information.
host name, press
.
• If the machine was unable to
receive an IP address automatically,
or if the router locked up after the
machine received an IP address,
[IP ADDRESS/DHCP: FAIL] /
[192.168. 1 .201] will appear.
“192.168. 1 .201“ is an IP address
that is assigned to the machine for
diagnostic purposes when
Checking your IP address and
the connection
To check the machine’s IP address and
verify that the machine is able to
communicate on the network, follow
these steps.
connection fails (it cannot be used
for regular communication).
1 Press FUNCTION , then
until
[NETWORK SETTING] appears.
• If a cable has not been connected,
[CHECK CABLE] will appear.
2 Press
, then
to show
• If [NOW CONNECTING / CHECK
[NETWORK INFORMATION]
STOP
LATER] appears, press
to exit,
wait briefly, and then repeat the
procedure again.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Machine
If the machine is unable to
communicate...
♦If [IP ADDRESS/DHCP: FAIL]
appears, remove and then reinsert
the Ethernet cable plug, and repeat
Steps 1 to 3 above. If the same
message appears, check the device
that acts as the DHCP server on your
network (try removing and restoring
the power). If your router is your
DHCP server, make sure that DHCP
is enabled in the router settings. If
your network does not have a DHCP
server, set a static IP address as
explained on page 23.
♦ Check the Ethernet cable. Are the
connections secure? Are you using
straight-through (not crossover) cable
for 10Base-T/100Base-TX?
♦ There may be a problem in the router
or other device to which the machine
is connected. Try removing and then
restoring the power to the router (see
the manual for the router).
♦If a static IP address has been set,
make sure that the network settings
16
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail Settings
Type in the host name or IP address of
the machine in the Address bar of the
Web browser on your computer.
E-mail Settings
Before the Fax to E-mail function can be
used, you must configure the e-mail
settings.
The Web page menu will appear. Select
E-mail Setup and configure the
settings. For explanations of the
settings, click Help in the Web page
menu.
The e-mail settings specify your
outgoing mail server, as well as your
sender name, sender address, and
other items that appear in the e-mail
message to which scanned image files
are attached.
Note: If the Web page is used while the
machine is in operation (except for
voice calls using the handset), machine
operation may become unstable.
♦ It is easiest to configure the e-mail
settings in the machine’s Web page.
The machine’s Web page can be
accessed from any computer on the
same network as the machine.
Using the machine’s operation
panel to configure the settings
Follow the steps below to display the e-
mail settings, and then configure each
setting as explained in the table on the
next page.
♦ The e-mail settings can also be
configured using the machine’s
operation panel.
1 Press FUNCTION , then
until
Note: If you need to configure “POP
before SMTP” settings, you must use
the Web page.
[E-MAIL SETTING] appears.
2 Press
, then
repeatedly
If you do not know your SMTP server
name or whether or not you need to
configure “POP before SMTP” settings,
ask your Internet service provider.
until the setting that you wish to
configure appears.
3 Press
. (Note: This step is not
Accessing the machine’s Web
page
necessary for the “FILE FORMAT”
setting.)
To access the Web page, you will need
to know the machine’s host name or IP
address (usually it is most convenient to
use the host name).
4 Enter the required information for
the setting as explained in the table
on the next page.
5 After configuring the setting, the
next e-mail setting will appear in the
display. You can configure the next
STOP
To check the machine’s host name or IP
address, follow the procedure in
Checking your IP address and the
setting, or press
to exit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail Settings
E-mail settings
Enter the required information for each setting as explained below.
This is done in step 4 of the procedure on the previous page.
♦ The sender address and SMTP server settings are required. The other settings are
optional.
♦ The e-mail subject, e-mail message, and file format that you enter below are default
settings. They will be used if you do not specify these items at the time of
transmission.
Setting
Description
SENDER
NAME
Enter the sender name that will appear in the e-mail message
(max. of 50 characters). When finished, press
Enter your sender e-mail address (max. of 128 characters). When
finished, press . (Note: Be sure to enter your actual e-mail
.
SENDER
ADDRESS
address. Return e-mail and undelivered mail reports will be sent to
this address. In addition, some SMTP servers reject outgoing e-
mail if a valid sender e-mail address is not entered.)
E-MAIL
Enter a default subject (max. of 128 characters). When finished,
SUBJECT
press
Enter a default message (max. of 256 characters). When finished,
press
This sets the default format of the file that is created when you
.
E-MAIL
MESSAGE
.
FILE FORMAT
scan a document. Press
for TIFF or
for PDF.
Initial setting: TIFF
SMTP SERVER Enter the host name or IP address of your outgoing (SMTP) mail
server (max. of 60 characters). When finished, press
.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing E-mail Addresses
and enter the desired 2-digit
number (01 to 63).
Storing E-mail Addresses
• If you prefer to have the machine
suggest an available Rapid Key /
Speed Dial number at the end of the
You can store e-mail addresses in the
A, B, and C keys, in Rapid Keys, and in
Speed Dial numbers.
procedure, press
.
♦ An e-mail address stored in a Rapid
Key or the A, B, or C key is selected
by simply pressing that key. A total of
36 Rapid Keys are available.
(Note: Attach the Rapid Key labels as
shown on page 5.)
3 Press
to select E-MAIL.
Display: [E-MAIL # MODE]
4 Enter the e-mail address with the
letter and number keys (max. of 128
characters).
♦ An e-mail address stored in a Speed
Dial number is selected by pressing
• For information on using the letter
keys, see page 6.
SPEED DIAL
and entering the 2-digit Speed
Dial number. A total of 63 Speed Dial
numbers are available.
• To clear a mistake, press
5 Press
.
Note: Rapid Keys and Speed Dial
.
6 Enter the name of the recipient
Storing an e-mail address
(max. 20 characters).
Follow the steps below to store an e-
mail address using the machine’s
operation panel.
7 Press
.
• If you selected a Rapid Key or
♦ E-mail addresses can also be stored
using the machine’s Web page. To
access the Web page, see page 17.
Speed Dial number in Step 2, the
display will briefly show [STORED],
and then [NEW NUMBER]. Go to
Step 8.
FUNCTION
1 Press
,
, then
.
• If you did not select a Rapid Key or
Speed Dial number in Step 2, the
display will show the next available
Rapid Key or Speed Dial number. If
that number is acceptable, press
2 To store an e-mail address in the A,
B, or C key, press the desired key
and go directly to Step 4.
To store an e-mail address in a
Rapid Key, press the desired Rapid
Key.
and go to Step 8. If not, press
To store an e-mail address in a
the desired Rapid Key, or press the
SPEED DIAL
SPEED DIAL
Speed Dial number, press
A, B, or C key, or press
and
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax to E-mail Transmission
enter the desired 2-digit Speed Dial
number, and go to Step 8.
• If you do not wish to change the
address, go directly to Step 5.
8 Return to Step 2 to store another e-
5 Press
.
STOP
mail address, or press
to exit.
6 Make the desired changes to the
name.
Editing and clearing stored e-
mail addresses
• If you do not wish to change the
name, go directly to Step 7.
To make changes to a previously stored
e-mail address, or to clear an address,
follow these steps:
7 Press
.
FUNCTION
8 Return to Step 2 to edit or clear
1 Press
,
, then
.
STOP
another address, or press
exit.
to
2 Press the key in which the address
is stored (Rapid Key or A, B, or C
SPEED DIAL
key), or press
and enter the
Fax to E-mail Transmission
2-digit Speed Dial number in which
the address is stored.
Follow the steps below to send a
document to an e-mail recipient.
(You can also press
or
until the name or address appears
♦The document will be sent as an
attachment to an e-mail message.
and press
.)
Display: [1=EDIT, 2=CLEAR]
♦You can specify the recipient by
directly entering an e-mail address, or
by selecting an address that has been
stored as explained in the previous
section.
3 Press
CLEAR.
for EDIT or
for
• If you selected CLEAR, go to Step 8.
1 Flip up the feeder cover (➊) and
adjust the document guides to the
width of your document (➋).
4 If you selected EDIT, make the
desired changes to the address.
• Press
or
to move the
cursor to the character(s) you wish to
change, and then press the
appropriate letter or number key. The
new character will replace the old
character.
2
1
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax to E-mail Transmission
2 Insert the
document
face down
with the top
edge going
in first.
or address appears, and press
.
Note: If [CHECK E-MAIL SETTING]
appears, your SMTP server or
sender address has not been
entered in the e-mail settings (p. 17).
4 If you need to select or change any
• Up to 20 letter-size sheets (5 legal-
size sheets) can be placed in the
feeder at once.
of the e-mail options, press
and follow Steps
5 and 6 below. (Note that settings
selected here are temporary. To
make permanent changes, see p.
17.)
• For more information on loading the
If you do not wish to change the e-
mail options, go directly to Step 7.
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
• To exit the e-mail options, press
3 Enter the destination e-mail address
and go to Step 7.
using one of the following methods:
5 Press
or
until the
• Press
, press
desired option appears, and press
, and enter the address with the
(
is not necessary for
the FILE FORMAT setting). Change
the option as explained below (use
the letter keys to enter text and
finished, press
.
• If the address has been stored in the
to delete text; p. 6).
A, B, or C key, press the key.
• E-MAIL SUBJECT: Enter a subject
(max. 128 characters). When
• If the address has been stored in a
Rapid Key, press the Rapid Key.
finished, press
.
• If the address has been stored in a
SPEED DIAL
• E-MAIL MESSAGE: Enter a
message (max. 256 characters).
Speed Dial number, press
and enter the Speed Dial number.
When finished, press
.
• To search for a stored address, press
(this eliminates
stored fax numbers from the search),
• FILE FORMAT: Press
for TIFF
or
for PDF. (Make sure the
press
or
until the name
recipient has an image viewer that
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax to E-mail Transmission
[CONNECTION ERROR]
can show images in the selected
format.)
This appears when communication
does not take place correctly on your
local network, usually due to a problem
with the cable connections. Make sure
that the cable ends are securely
inserted in the LAN ports. Make sure
that the correct cable is being used and
that the cable is good. Make sure that
your router or hub is powered on.
• FILE NAME: Enter a name for the
scanned file (max. 40 characters).
When finished, press
.
6 When you have finished configuring
the e-mail options, press
. (If the display
shows [PRESS START TO SCAN],
it is not necessary to press
[SERVER ERROR]
This appears when the machine cannot
connect to your mail server or there is
no response from the mail server.
Make sure the SMTP server setting is
“POP before SMTP” settings in the
Web pages, make sure these settings
are correct.
.)
7 Press
to begin transmission.
Note: The recipient may have security
settings in their e-mail program or virus
protection software that prevent the file
attachment from being received or
opened. In this case, ask the recipient
to try changing the settings.
[SERVER NOT FOUND] / [SMTP]
This appears when an incorrect host
name is entered for your SMTP server.
Check the SMTP server setting (p. 18).
[SERVER NOT FOUND] / [DHCP]
This appears when the machine is
unable to automatically obtain an IP
address. Restart your router or other
device that acts as your DHCP server.
Sending a message only
You can also send a short e-mail
message without including a
document. Perform Steps 3 through 7
of the above procedure (enter the
message in Step 5). After Step 7,
[SEND W/O DOCUMENT?] /
[1=YES,2=NO,W/T DOC.]
[CABLE DISCONNECTED]
This may appear below any of the
above messages. Check the same
items as in [CONNECTION ERROR]
above.
will appear. Press
to select
“YES”. The message will be sent.
If an undelivered mail report is sent
to inform you that your e-mail
message was not successfully
delivered, the report will be sent to
the sender address entered in the e-
mail settings (page 17).
Error messages
If transmission is not successful
because the machine is unable to
connect to your mail server, one of the
following error messages will appear.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
• Three digits must be entered in each
segment of the number (the
Network Settings
segments are separated by
If your network requires that you assign
a static (permanent) IP address to the
machine, follow the steps below to
disable DHCP (automatic IP address
assigment) and configure the network
settings.
periods). If a segment does not have
3 digits, enter zeros as needed.
Example: IP address = 192.168.1.2
You must enter: 192.168.001.002
• If you make a mistake, press
• Consult your network administrator
for the information that must be
entered. After DHCP is disabled, the
settings that must be configured
appear in the following order (these
settings only appear when DHCP is
set to NO):
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS (PRIMARY)
to move the cursor to the mistake
and enter the correct number.
6 When finished entering the number,
press
.
7 The next setting will appear in the
display. Repeat Steps 4 through 6
to configure the next setting, or
STOP
press
to exit.
DNS (SECONDARY)
1 Press FUNCTION , then
until
Initializing the network settings
[NETWORK SETTING] appears.
If you need to return the network
settings to their initial state, follow the
steps below.
2 Press
twice.
[DHCP] will appear.
• Initializing the settings enables
DHCP and clears the IP address
and related settings.
3 Press
for NO (the machine will
not obtain an IP address
automatically).
1 Press FUNCTION , then
until
• [IP ADDRESS] will appear.
(If you wish to configure a different
[NETWORK SETTING] appears.
setting, press
or
.)
2 Press
twice, then
to
show [INITIALIZE SETTINGS].
4 Press
.
5 Press the number keys to enter the
3 Press
twice.
required number.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Sending Faxes
♦ Documents which are taped, torn,
smaller than the minimum size,
carbon backed, easily smudged, or
have a slick, coated surface should be
photocopied, and the copy loaded in
the feeder.
Transmittable Documents
Minimum document size/weight
Loading up to 20 sheets at once:
5.8” x 5.5” (148 x 140 mm)
2
14 lbs. (52 g/m )
♦ Documents that are curled or have a
wave-like pattern must be flattened.
Loading 1 sheet at a time:
2.8” x 5.5” (70 x 140 mm)
2
Loading the Document
14 lbs. (52 g/m )
Up to 20 letter-size sheets (5 legal-size
sheets) can be placed in the feeder at
once. (If the sheets do not feed or
double feeds occur, reduce the number
of sheets.) The sheets will feed
automatically starting from the bottom
sheet.
Maximum document size/weight
Loading up to 20 sheets at once:
Letter (8.5” x 11”, 216 x 279 mm)
2
20 lbs. (75 g/m )
Loading up to 5 sheets at once:
Legal (8.5” x 14”, 216 x 356 mm)
2
♦To send or copy more than the
maximum number of sheets, place
the additional sheets gently in the
feeder just before the last sheet is
scanned. Do not force the sheets in,
as this may cause double-feeding or
jamming.
20 lbs. (75 g/m )
Loading 1 sheet at a time:
Legal (8.5” x 14”, 216 x 356 mm)
2
42 lbs. (157 g/m )
The maximum scanning width is 8.2”
(208 mm), and the top and bottom
0.16” (4 mm) of a document cannot
be scanned.
♦For large or thick sheets that must be
loaded one at a time, insert each
sheet into the feeder as the previous
sheet is being scanned. Insert gently
to avoid double-feeding.
Other restrictions
♦ The scanner cannot recognize yellow,
1 Flip up the feeder cover (➊) and
adjust the document guides to the
width of your document (➋).
greenish yellow, or light blue ink.
♦ Remove all clips, staples, and pins
before loading documents in the
feeder (these will damage the
machine).
2
♦ Ink, glue, or correcting fluid on a
document must be dry before
scanning.
1
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Resolution and Contrast
Resolution and Contrast
2 Place the document face down with
the top edge going in first, and
insert it all the way into the feeder.
Make sure that the roller draws the
document in.
You can adjust the resolution and
contrast before sending a document.
♦The default resolution setting is
STANDARD. The default contrast
setting is AUTO.
♦Adjust the settings each time you
don't want to use the default settings.
Note: The resolution and contrast
settings are only effective for sending;
not for receiving.
• Display: [READY TO SEND] .
3 Adjust the resolution and/or contrast
receiving machine (p. 26).
Resolution settings
STANDARD Use STANDARD for
ordinary documents.
Removing a document from the
feeder
This provides the fastest
transmission.
1 Open the cover (➊) and remove the
document (➋).
FINE
Use FINE for documents
containing small letters
or fine drawings.
• Caution: Attempting to remove a
document without opening the cover
may damage the feeder mechanism.
SUPER FINE Use SUPER FINE for
documents containing
very small letters or very
fine drawings.
2
1
HALF TONE Use HALF TONE for
photographs and
illustrations. The original
will be reproduced in 64
shades of gray.
2 Close the cover, pressing down
firmly on both front corners.
Contrast settings
AUTO
DARK
Use AUTO for normal
documents.
Use DARK for faint
documents.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax: Normal Dialing
1 Load the document(s).
♦Normal Dialing allows you to listen to
the line and make sure the other fax
machine is responding.
• The resolution/contrast cannot be
adjusted unless the document is
loaded.
1 Load the document(s).
RESOLUTION/
RESOLUTION/
RECEPTION MODE
RECEPTION MODE
2 Press
one or more times
• If desired, press
to set the
until the desired resolution and
contrast settings appear in the
display.
resolution and/or contrast.
SPEAKER
2 Pick up the handset or press
.
• The first time you move through the
list of resolution settings, the contrast
setting AUTO will appear next to
each resolution setting. The second
time you move through the list, the
contrast setting DARK will appear.
Listen for the dial tone.
3 Dial the fax number of the receiving
machine (press the number keys).
4 Wait for the connection. You will
either hear a fax tone or the other
person will answer.
Note: In order to transmit in SUPER
FINE resolution, the receiving machine
must also have that resolution. If not,
your machine will automatically step
down to FINE.
• If the other person answers, ask
them to press their Start key (if you
pressed SPEAKER , pick up the handset
to speak with them). The receiving
machine will issue a fax tone.
If you prefer to use FINE for the
default resolution setting, change the
5 When you hear the fax tone, press
. Replace the handset.
• If the transmission is completed
successfully, the machine will beep
once.
Sending a Fax: Normal Dialing
• If an error occurs, the machine will
beep three times and print a
Transaction Report to inform you of
With Normal Dialing, you pick up the
handset (or press SPEAKER ) and dial by
pressing the number keys.
Note: If the transmission is
♦ If a person answers, you can talk with
them through the handset before
sending the fax.
unsuccessful and the display shows
[DOCUMENT JAMMED], remove the
document as explained on page 62.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax: Auto Dialing
desired 2-digit number (01 to 63).
Display: [SELECT DEST. TYPE]
Sending a Fax: Auto Dialing
• If you prefer to have the machine
suggest an available Rapid Key /
Speed Dial number at the end of the
You can store your most frequently
dialed fax and phone numbers in Rapid
Keys and Speed Dial numbers.
procedure, press
.
♦ A number stored in a Rapid Key is
dialed by simply pressing the Rapid
Key. A total of 36 Rapid Keys are
available. (Note: Attach the Rapid Key
labels as shown on page 5.)
3 Press
to select “FAX”.
Display: [FAX # MODE]
4 Enter the fax or phone number with
the number keys (max. of 32 digits).
(Note: A space cannot be entered.)
♦ A number stored in a Speed Dial
SPEED DIAL
number is dialed by pressing
,
• To clear a mistake, press
.
the 2-digit Speed Dial number, and
• If a pause is required between any of
then
. A total of 63 Speed Dial
the digits to access a special service
numbers are available.
or an outside line, press FUNCTION . The
Note: E-mail addresses can also be
stored in Rapid Keys and Speed Dial
pause appears as a hyphen (two
seconds per pause). Several pauses
can be entered in a row.
Storing fax and phone numbers
5 Press
.
Follow the steps below to store a fax or
phone number using the machine’s
operation panel.
6 Enter the name of the destination
(max. 20 characters).
♦ Fax/phone numbers can also be
stored using the machine’s Web page.
To access the Web page, see page
• For information on using the letter
7 Press
.
FUNCTION
1 Press
,
, then
.
• If you selected a Rapid Key or
Speed Dial number in Step 2, the
display will briefly show [STORED],
and then [NEW NUMBER]. Go to
Step 8.
2 To store a number in a Rapid Key,
press the desired Rapid Key.
To store a number in a Speed Dial
SPEED DIAL
number, press
and enter the
• If you did not select a Rapid Key or
Speed Dial number in Step 2, the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax: Auto Dialing
display will show the next available
Rapid Key or Speed Dial number. If
that number is acceptable, press
• If you selected “CLEAR”, go to Step
7.
4 If you selected “EDIT”, make the
desired changes to the number.
and go to Step 8. If not, press
the desired Rapid Key, or press
• Press
or
to move the
SPEED DIAL
and enter the desired 2-digit
cursor to the digit or digits you wish
to change, and then enter the new
digit. The new digit will replace the
old digit.
Speed Dial number, and go to Step
8.
8 Return to Step 2 to store another
STOP
• If you do not wish to change the
number, go directly to Step 5.
number, or press
to exit.
Editing and clearing auto-dial
numbers
5 Press
.
6 Make the desired changes to the
To make changes to a previously stored
auto-dial number, or clear a number,
follow these steps:
name.
• Press
or
to move the
FUNCTION
cursor to the letter or letters you wish
to change, and then press the
appropriate letter key. The new letter
will replace the old letter.
1 Press
,
, then
.
2 Press the Rapid Key (or press
SPEED DIAL
and enter the 2-digit Speed
• If you do not wish to change the
name, go directly to Step 7.
Dial number) of the number that you
want to edit or clear. (You can also
press
or
until the
7 Press
.
number appears and press
.)
8 Return to Step 2 to edit or clear
STOP
Display: [1=EDIT, 2=CLEAR]
another number, or press
exit.
to
3 Press
“CLEAR”.
for “EDIT” or
for
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax: Auto Dialing
• If an error occurs, the machine will
beep three times and print a
Transaction Report to inform you of
Using an auto-dial number to
send a fax
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
Making a voice call with an auto-dial
number
If desired, press
to set the
resolution and/or contrast.
Rapid Key Dialing: Lift the handset
and press the Rapid Key.
2 Select the fax number using one of
the methods below:
Speed Dialing: Lift the handset, press
SPEED DIAL , and enter the 2-digit Speed Dial
• Rapid Key Dialing: If the number is
stored in a Rapid Key, press the
Rapid Key.
number with the number keys.
• Speed Dialing: If the number is
stored in a Speed Dial number, press
SPEED DIAL
Search Dialing: Press
or
and enter the Speed Dial
until the name or number of the other
party appears, and lift the handset.
(You can also lift the handset first,
search for the number, and then press
number with the number keys. Make
sure the correct destination appears
STOP
in the display (if not, press
), and
.)
then press
.
• Search Dialing: Press
or
until the name or number of
the other party appears in the
display, and press
.
3 Dialing and transmission will take
place automatically.
STOP
• To cancel transmission, press
.
• If the transmission is completed
successfully, the machine will beep
once.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax: Auto Dialing
Sending a fax by Direct Keypad
Dialing
2 Press
once. Make sure the
display shows the number you wish
to dial.
Use this method to dial a full fax
number without using the handset .
3 If you are sending a fax, press
1 Load the document(s).
. Dialing begins.
RESOLUTION/
RECEPTION MODE
• If desired, press
resolution and/or contrast.
to set the
If you are making a phone call, lift
the handset. Dialing begins.
Note: If the transmission is
unsuccessful and [DOCUMENT
JAMMED] appears in the display,
remove the document as explained on
2 Enter the number of the receiving
machine with the number keys.
• If a pause is required between any of
the digits to access a special service
or an outside line, press FUNCTION . The
Automatic redialing
pause will appear as a hyphen (two
seconds per pause). Several pauses
can be entered in a row.
If you use auto dialing (including Direct
Keypad Dialing) to send a fax and the
line is busy, the machine will
automatically make three redial
attempts at intervals of five minutes.
3 Check the display. If the number
shown is correct, press
.
During this time, [RECALLING] will
appear in the display, followed by the
attempt number. You will not be able to
dial any other locations while the
message appears.
• If the number is not correct, press
STOP
to clear the incorrect digits, and
then re-enter the correct digit(s).
♦To clear the message and stop
Redial
STOP
automatic redialing, press
.
You can automatically redial the last
number dialed on the machine.
Under certain conditions, automatic
redialing may stop before three
redialing attempts are made.
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Batch Page Numbering
Sending a Fax From Memory
Batch Page Numbering
Use this feature to add a slash and the
total number of pages to each page
number on transmitted fax pages (for
example, "P. 1/5", "P.2/5", etc.). This
allows the recipient to check for missing
pages.
To increase transmission speed, you
can send a fax through the machine’s
memory. After transmission, the fax is
automatically cleared from memory.
Note: If a power failure occurs while
sending a fax from memory, you must
repeat the operation.
1 Load the document(s).
To send a fax through memory, load the
2 Press FUNCTION , then
to show
document, press
, and dial using
[PAGE COUNTER].
one of the methods below. (Note that
an e-mail destination cannot be
selected.)
3 Press
.
Display: [ENTER # (01 - 99)]
♦ Press a Rapid Key.
4 Enter the total number of pages
(“01” to “99”) with the numeric keys.
♦ Press SPEED DIAL , enter a 2-digit Speed
Example: 5 pages
.
RESOLUTION/
RECEPTION MODE
Dial number, and press
♦ Enter the fax number with the number
keys and press
.
5 If desired, press
to set the
resolution and/or contrast.
6 Dial the receiving machine and
.
send the fax.
• To cancel a batch number entry,
remove the document from the
STOP
♦ Press
repeatedly to select an
feeder or press
.
auto-dial number and press
.
• If the number of pages actually
transmitted is not the same as the
batch number entered, an alarm will
sound and [PAGE COUNT ERROR]
will appear in the display. “PAGE E.”
will also appear in the NOTE column
of the Transaction Report if printed.
♦ Press
once to select the last
number dialed and press
.
If [MEMORY FULL] appears, see If
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Receiving Faxes
Answering with the machine’s
handset
Using AUTO Mode
To select AUTO mode, press
Important: If a document is loaded in
the machine’s feeder, remove it before
performing the steps below.
RESOLUTION/
RECEPTION MODE
(with no document in the
feeder) until [AUTO] appears in the
display.
1 When the machine rings, pick up
the handset.
In AUTO mode, the machine
automatically answers all calls on 4
rings and receives incoming faxes.
2 If you hear a fax tone, wait until the
display shows [RECEIVING] and
then replace the handset.
♦If you pick up the handset before the
machine answers, you can talk to the
other party and receive a fax as
explained in Using MANUAL Mode
below.
• If [RECEIVING] does not appear (or
if you have set the Fax Signal
press
to begin reception.
To change the number of rings on
which the machine answers calls,
change the “NUMBER OF RINGS”
3 If the other party first speaks with
you and then wants to send a fax,
press
after speaking. (Press
before the sender presses their
Start key.)
The machine automatically reduces
received faxes as needed to fit the
paper. If you prefer to have all faxes
printed at full size, change the
• When [RECEIVING] appears in the
display, hang up.
Answering a call on an
extension phone connected to
the same line
Using MANUAL Mode
1 Answer the extension phone when
it rings.
To select MANUAL mode, press
RESOLUTION/
RECEPTION MODE
2 If you hear a soft fax tone, wait until
you hear pronounced, high-pitched
fax tones, then hang up.
(with no document in the
feeder) until [MANUAL] appears in
the display.
3 If the machine doesn't respond, or if
the other party first talks to you and
then wants to send a fax, set the
phone down (do not hang up), walk
over to the machine, lift the
In MANUAL mode, you must answer all
calls (even faxes) by picking up the
machine’s handset or an extension
phone connected to the same line.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TEL/FAX Mode
machine’s handset, and press
.
♦ If your machine doesn't detect a fax
tone (this means that the call is a
voice call or manually dialed fax), it
will make a special ringing sound for
15 seconds to alert you to pick up the
machine’s handset (to change the
“PSEUDO RING DURATION” on p.
46). If you don't answer within this
time, the machine will send a fax tone
to the other machine to allow the
calling party to send a fax manually.
• The above step is necessary if you
have set the “FAX SIGNAL RX”
Putting a call on hold
To put the other party on hold during a
phone call, press HOLD . When this is
done, they cannot hear you. You can
put the handset back in the cradle
without breaking the connection. When
you are ready to speak with the other
party again, pick up the handset. If you
did not put the handset back in the
HOLD
Note: Only the machine will make the
special ringing sound. An extension
phone will not ring after the machine
initially answers the call.
Reception to Memory
cradle, press
again to resume
conversation.
Incoming faxes will be received to
memory when printing is not possible,
such as when the machine runs out of
paper, the print cartridge needs
replacement, or the paper jams.
TEL/FAX Mode
To select TEL/FAX mode, press
RESOLUTION/
RECEPTION MODE
When you have received a fax in
(with no document in the
memory, [FAX RX IN MEMORY] will
appear in the display, alternating with a
message that indicates the problem.
feeder) until [TEL/FAX] appears in
the display.
When the reception mode is set to TEL/
FAX, the machine automatically
answers all calls on 2 rings. After
answering, the machine monitors the
line for about five seconds to see if a
fax tone is being sent.
When you resolve the problem, the
stored faxes will automatically print out.
♦If you received faxes to memory
because the machine ran out of
paper, be sure to add paper that is
the same size as the paper
previously used, or the fax print-out
size will not match the size of the
printing paper.
♦ If the machine detects a fax tone (this
means that the call is an
automatically dialed fax), it will
automatically receive the fax.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Making Copies
The machine can be used as a
convenience copier. Follow the steps
below to make copies.
3 When you are ready to begin
COPY/HELP
copying, press
.
Sorting copies
If [MEMORY FULL] appears...
The machine is initially set to not sort
copies. If you wish to have copies
sorted as shown below, change the
“SORT COPY” setting to YES (pp. 45
If you place many originals in the
feeder, the memory may become full
before all pages can be scanned (the
display will show [MEMORY FULL]). If
this happens, only the pages that were
scanned will be copied and the
Originals
C
B
A
remaining pages will automatically feed
out. Repeat the copy procedure for the
remaining pages, including the page
that was being scanned when the
memory became full.
Sorted (SORT COPY)
Not sorted (MULTI COPY)
A
B
C
C
C
A
B
B
B
C
A
A
Example: Two copies
each of three originals
Note: It may not be possible to make a
copy of an original if a high resolution
setting is used and/or the original
contains so much detailed content that
the memory becomes full before
scanning finishes.
1 Load the document(s). (Maximum
of 20 letter sheets or 5 legal sheets.)
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
2 Select the following copy settings as
needed:
• Enlarge/reduce: Press
or
to select 100%, 125%, 135%,
200%, 70%, 88% or 94%.
Default setting: 100%.
• Number of copies per original:
Enter a number from 1 to 99.
Default setting: 1
Example: Press
for two copies
34
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Special Functions
Broadcasting
5 Press
destination.
to enter the
You can send the same document to as
many as 20 fax or e-mail destinations in
just one operation.
6 Repeat Steps 4 and 5 for each of
the other desired destinations
(maximum of 20).
♦The destinations must be all fax or all
e-mail. It is not possible to mix fax
and e-mail destinations.
• You can press
through and check your entered
destinations. To delete a
to scroll
♦Only destinations stored in Rapid
Keys and Speed Dial numbers can be
selected. (It is not possible to enter a
full fax number or e-mail address.)
destination, press
appears.
when it
7 When you have finished selecting
destinations, press
1 Load the document(s).
.
RESOLUTION/
RECEPTION MODE
• If desired, press
resolution and/or contrast.
to set the
• If you are broadcasting to fax
destinations, transmission will
begin.
B'CAST
2 Press
.
• If you are broadcasting to e-mail
3 Press
to broadcast to FAX
to broadcast
to E-MAIL destinations.
destinations, you can press
to select e-mail
options (see Steps 4 to 6 on page
21). When you are ready to begin
destinations, or
4 Select a destination using one of
the following methods:
transmission, press
.
• Press a Rapid Key.
• For fax, a Transaction Report is
automatically printed out after
Broadcasting is completed. If any
destinations in the "Note" column of
the report are marked "Busy" or
have a communication error code,
you will need to send the document
to those destinations again.
SPEED DIAL
• Press
and enter a 2-digit
Speed Dial number.
• Press or
desired destination appears in the
display.
until the
• Press
destination).
,
, or
(only for an e-mail
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadcasting
• If the group is an e-mail group, you
can press to
select e-mail options (see Steps 4 to
If the memory becomes full...
If the memory becomes full during
scanning, [MEMORY FULL] will
appear in the display.
to begin transmission, press
.
♦ Press
to send the pages
Storing destinations in Group
Keys
which have been stored up to that
point in memory (the remaining
pages will automatically feed out).
After transmission, the memory will
be cleared and you can send the
remaining pages. You will also need
to send the page which was being
scanned when the memory filled
up.
Follow the steps below to store a group
of destinations in a Group Key.
♦Rapid Keys 33/G1 and 34/G2 can be
used as Group Keys. A key cannot be
simultaneously programmed as both
a Group Key and a Rapid Key.
♦Up to 20 fax or e-mail destinations
can be stored in one Group Key.
♦ To cancel the entire transmission,
STOP
press
.
♦The destinations must be all fax or all
e-mail. It is not possible to mix fax and
e-mail destinations.
Broadcasting using a Group
Key
♦Only Rapid Key and Speed Dial
numbers can be stored in a Group
Key. Full numbers cannot be stored.
If the destinations to which you want to
broadcast have all been stored in one
Group Key (see Storing numbers in
Group Keys which follows), you can
perform the broadcast operation using
the following simplified procedure:
1 Press FUNCTION , then
until
[ENTRY MODE] appears.
1 Load the document(s).
2 Press
, then
until
RESOLUTION/
RECEPTION MODE
[GROUP ENTRY] appears.
• If desired, press
to set the
resolution and/or contrast.
3 Press
(SET) to store a group.
(CLEAR) to clear a
2 Press the appropriate Group Key
(Press
group.)
33/G1
34/G2
(
or
).
• If [GROUP SPACE FULL] appears,
both keys have already been
• If the group is a fax group,
transmission will begin.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Service)
programmed. Clear one of the keys
and then store a group.
8 When you have finished entering
the destinations, press
.
4 Press the Group Key that you want
33/G1
34/G2
STOP
to use (
or
). (If you are
9 Press
to exit.
clearing a Group Key, press the
Group key that you want to clear
and go to Step 8.)
Caller ID (Requires Service)
• If [ALREADY STORED] or [RAPID #
STORED] appears, the key has
already been programmed. Clear the
key or try the other Group Key.
Important: To use this function, you
must subscribe to a Caller ID service
from your phone company. The
machine may not be compatible with
some Caller ID services.
5 Select a destination using one of the
following methods:
• Press a Rapid Key.
If you subscribe to a Caller ID service,
you can have the machine show the
name and number of the caller when
you receive a call.
SPEED DIAL
• Press
and enter a 2-digit
Speed Dial number.
• Press or
desired destination appears in the
display.
until the
1 Press FUNCTION , then
until
[OPTION SETTING] appears.
• Press
destination).
6 Press
,
, or
2 Press
, then
until
(only for an e-mail
[CALLER-ID] appears.
3 Press
(YES) to turn on Caller
to enter the destination.
ID. (To turn off Caller ID, press
and go to Step 7.)
7 Repeat Steps 5 and 6 for each of
the other desired destinations
(maximum of 20).
4 If the area code must not be
included when you dial a local
phone number (within your area
code), press
to select SET
• You can press
to scroll through
and enter your area code in Step 5.
(This will remove the area code from
local numbers stored in the Caller
ID list, allowing you to automatically
dial those numbers from the list (see
and check your entered destinations.
To delete a destination, press
when it appears.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Service)
Caller ID list on this page).)
If you do not need to have the area
code removed from local numbers
Caller ID list
The machine keeps a log of the most
recent 30 calls and faxes you have
received (the Caller ID list). You can
view the list and automatically dial a
number from the list.
in the Caller ID list, press
go to Step 7.
and
5 Enter the 3 digits of your area code.
♦The list is only available if you have
Caller ID service and have turned on
the Caller ID function.
6 Press
.
STOP
7 Press
to exit.
♦After you have received 30 calls, each
new call will delete the oldest call.
Note: Some caller ID services may not
provide the name of the caller. In this
case, only the phone number will
appear when you receive a call.
♦The Caller ID list can also be printed.
1 Press
until [<REVIEW
Display messages
CALLS>] appears.
One of the following messages will
appear while the machine rings if caller
information is not available.
2 Press
or
to scroll
through the list.
NO
SERVICE
No caller information was
received. Make sure that
your service has been
activated.
STOP
• To exit the list, press
.
3 To dial a number, display the
CALLER-ID Noise on the telephone
number and:
line prevented reception of
caller information.
ERROR
• Fax: Load the document and press
OUT OF
AREA
The call was made from an
area which does not have
Caller ID service, or the
service is not compatible
with your service.
. Transmission will begin.
• Voice call: Pick up the handset.
Dialing will begin automatically.
Deleting calls from the list
PRIVATE
CALL
Caller information was not
provided at the caller’s
request.
To delete a single call from the list,
display the call and press
.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Service)
To delete all calls from the list, hold
down for 3 seconds while viewing
any number in the list.
3 Select the ring pattern below that
matches the ring pattern of your
second number. (To use your first
number as a fax number, select
STANDARD RING.)
Blocking voice calls
RING PATTERN 1
Two short rings
If you have turned on Caller ID, the Anti
Junk Fax function will block voice calls
as well as faxes from your specified Anti
Junk Number (see p. 40).
RING PATTERN 2
One short, one long, and
one short ring
Note: This function cannot be used if
you are using Distinctive Ring.
RING PATTERN 3
Two short rings and one
long ring
Distinctive Ring (Requires Service)
RING PATTERN 4
Three very short rings
(Canada only)
Important: To use this function, you
must subscribe to a Distinctive Ring
service from your telephone company.
The machine may not be compatible
with some Distinctive Ring services.
RING PATTERN 5
Two very short rings
(Canada only)
STANDARD RING
Your standard (normal)
ring pattern
Distinctive Ring is a service offered by
some local telephone companies
whereby they assign an additional
second number to your regular single
line. The second number rings
OFF SETTING
Turn distinctive ring off
differently from your normal number.
STOP
4 Press
to exit.
If you subscribe to a Distinctive Ring
service, you can set the machine to
automatically answer when your second
number is called. This allows you to use
the second number as an exclusive fax
number.
RESOLUTION/
RECEPTION MODE
5 Press
to set the reception
mode to AUTO.
♦ To use Distinctive Ring, the reception
mode must be set to AUTO. When
your designated fax number is dialed,
the machine will automatically answer
and begin reception after two rings. If
one of your other numbers is dialed,
the machine will ring; however, it will
not answer.
1 Press FUNCTION , then
until
[OPTION SETTING] appears.
2 Press
, then
until
[DISTINCTIVE RING] appears.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking Unwanted Faxes
Blocking Unwanted Faxes
Duplex Scanning
The Anti Junk Fax function blocks
reception of faxes from a fax number
that you specify.
Duplex Scanning is convenient for
transmitting or copying two-sided
documents. When this function is
selected, you simply feed all pages of
the document through the machine
once, turn the stack of pages over, and
feed the stack through again. The
machine will automatically sort the
pages into the correct order (front of 1st
page, back of 1st page, front of 2nd
page, back of 2nd page, etc.).
To use this function, enter the fax
number that you want to block. Only one
number can be entered.
1 Press FUNCTION , then
until
[ENTRY MODE] appears.
♦ Note that any blank sides must be
included when scanning the pages (if
the number of pages is not equal
each time the machine scans the
stack, an error will result).
2 Press
, then
until [ANTI
JUNK #] appears.
3 Press
Junk number.
(To clear a previously stored
(SET) to store an Anti
1 Load the documents. Make sure the
pages are placed front-side down,
with the first page on the bottom.
number, press
go to Step 5.)
(CLEAR) and
RESOLUTION/
4 Enter the number with the number
RECEPTION MODE
• If desired, press
to set the
keys (max. 20 digits).
resolution and/or contrast.
5 Press
.
DUPLEX
2 Press
and then
.
STOP
6 Press
to exit.
3 Perform all steps of the desired copy
or transmission operation.
♦When a fax is blocked (or when a
voice call is blocked if you are using
the Caller ID function), a transaction
you (unless “TRANSACTION LIST” on
page 46 is set to “NEVER PRINT”).
4 When all pages of the document
have been scanned, turn the stack
over (do not change the page order)
and load the stack again.
5 Press
.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving Faxes to E-mail
1 Press FUNCTION , then
until
Receiving Faxes to E-mail
[RCV FAX TO E-MAIL] appears.
You can have incoming faxes from
specified fax numbers (or all fax
numbers) automatically converted to e-
mail and forwarded to designated e-mail
recipients.
2 Press
, then
to show
[FORWARDING ADDRESS] /
[1=SET, 2=CLEAR]
♦ This provides a convenient means of
forwarding received faxes to someone
who is out of the office.
3 Press
to select “SET”.
• To clear a previously stored group,
press
.
♦ This function can also be used to
send copies of all received faxes to an
administrator for centralized
document storage.
4 Enter a 2-digit number from “01” to
“10” (this number is used to identify
the group you will store).
Storing (or clearing) groups of
originating fax numbers and
forwarding e-mail addresses
• If you are clearing a group, enter the
2-digit number of the group you wish
to clear and go to Step 8.
To use the Receive Fax to E-mail
function, you must first store one or
more groups of originating fax numbers
and forwarding e-mail addresses.
5 Enter the originating fax number.
• If you wish to have faxes from all
originating fax numbers forwarded,
go directly to Step 6 without entering
a fax number.
♦ One originating fax number and one
forwarding e-mail address can be
stored in each group. When a fax is
received, the machine will check each
stored group, and if the originating
number of the received fax matches a
fax number in one of the groups, the
machine will forward the fax to the e-
mail address in that group.
6 Press
.
7 Enter the e-mail address to which
you wish to have the faxes
forwarded.
• For information on using the letter
keys, see page 6.
♦ You can also omit entry of an
originating fax number in a group and
have faxes from all originating fax
numbers forwarded to the e-mail
address.
8 Press
.
9 Return to Step 4 to store (or clear)
STOP
another group, or press
to exit.
♦ Up to 10 groups can be stored.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving Faxes to E-mail
Activating (and deactivating)
Receive Fax to E-mail
Printing a report
The machine is initially set to print a fax
forwarding report only when a
fowarding error occurs. If you would like
the machine to print a report each time
it forwards a received fax, follow the
steps below.
After you have stored one or more
Receive Fax to E-mail groups, follow the
steps below to activate the Receive Fax
to E-mail function.
1 Press FUNCTION , then
until
1 Press FUNCTION , then
until
[RCV FAX TO E-MAIL] appears.
[RCV FAX TO E-MAIL] appears.
2 Press
.
2 Press
, then
until
3 Press
to select “ON”.
[REPORT SETTING] appears.
• To turn off Receive Fax to E-mail,
3 Press
to print a report only when an error
occurs, or (ALWAYS PRINT)
(PRINT ERROR ONLY)
press
.
STOP
to print each time a fax is forwarded.
4 Press
to exit.
STOP
4 Press
to exit.
Printing forwarded faxes
The machine is initially set to not print
received faxes that are forwarded. If you
want the machine to print forwarded
faxes, follow the steps below.
1 Press FUNCTION , then
until
[RCV FAX TO E-MAIL] appears.
2 Press
, then
until [PRINT
RECEIVED FAX] appears.
3 Press
to select YES (print
forwarded faxes) or
NO.
to select
STOP
4 Press
42
to exit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Receive
Activating Secure Receive
Secure Receive
Follow the steps below to activate
Secure Receive.
To prevent others from viewing or taking
your received faxes, use the Secure
Receive function. When this function is
activated, received faxes are held in
memory without being printed. To print
the faxes, a 4-digit “secure code” must
be entered.
• Secure Receive cannot be activated
unless a secure code has been set.
SECURE
1 Press
, then
until
[ACTIVATE SECURE RCV.] appears.
Setting a secure code
2 Press
.
The secure code is used to print
received faxes. Follow the steps below
to set a secure code.
3 Press
to select “YES”.
STOP
• The secure code can be any 4-digit
number.
4 Press
to exit.
Printing received faxes
SECURE
1 Press
, then
until
When the memory is holding one or
more received faxes, [RECEIVED
SECURE FAX] will appear in the
display. Follow the steps below to print
the faxes.
[SECURE # SET] appears.
2 Press
.
3 Enter a 4-digit secure code.
SECURE
1 Press
to until [SECURE DATA
4 Press
.
PRINT] appears.
• The machine will print the secure
code for your records.
2 Press
.
3 Enter the 4-digit secure code.
• Take care not lose the print-out or
forget the code. In the event that you
forget the code and have kept no
record, contact Sharp’s Customer
Assistance Center at 1-877-794-
8675.
4 Press
.
• Printing will begin.
• If the wrong code is entered,
[WRONG SECURE #] will appear.
Go back to Step 3.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Receive
Deactivating Secure Receive
Clearing the secure code
If you need to deactivate Secure
Receive (faxes will be automatically
printed when received), follow the steps
below.
To clear the secure code, follow the
steps below.
• Secure Receive must be deactivated
before you can clear the secure
code.
SECURE
1 Press
, then
until
[ACTIVATE SECURE RCV.] appears.
SECURE
1 Press
, then
until
[SECURE # CLEAR] appears.
2 Press
.
2 Press
.
3 Press
to select “NO”.
3 Enter the 4-digit secure code.
4 Enter the 4-digit secure code.
4 Press
.
5 Press
.
• The display will briefly show
[CLEARED] and then the date and
time.
• The display will briefly show [NO
SELECTED] and then the date and
time.
• If the wrong code is entered,
[WRONG SECURE #] will appear.
Go back to Step 3.
• If the wrong code is entered,
[WRONG SECURE #] will appear.
Go back to Step 4.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Option Settings and Print Settings
The option settings and print settings
allow you to customize the operation of
the machine to better suit your needs.
2 Press
, then
repeatedly
until the desired setting appears.
The option settings are related to
general operation. The print settings are
related to printing.
• The option settings and print settings
are described in the tables below
and on the following pages.
The option settings and print settings
have been initially configured at the
factory. To change a setting, follow the
steps below to display the desired
setting, and then change the setting as
explained in the tables that follow.
3 Enter a selection for the setting by
pressing the number keys as
explained in the table.
4 After entering a selection, the
subsequent option/print setting will
appear in the display. To exit the
STOP
1 Press FUNCTION , then
until
settings, press
.
[OPTION SETTING] or [PRINT SET-
UP] appears.
Option Settings
Make a selection for the displayed setting as explained below.
This is done in step 3 of the above procedure.
Setting
Description
FINE PRIORITY This is used to change the default resolution for faxing from
STANDARD to FINE. Press
(YES) to select FINE, or
(NO) to select STANDARD.
Initial setting: NO (STANDARD)
NUMBER OF
RINGS
This is used to set the number of rings on which the machine
answers calls when the reception mode is set to AUTO. Enter any
number from 2 to 5.
Initial setting: 4 rings.
machine will answer after 2 rings regardless of this setting.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Option Settings
TRANSACTION This sets the condition for printing transaction reports (see page
LIST
51). Press a number key as follows:
(ALWAYS PRINT): Print after every fax transmission,
reception and error.
(ERROR/MEMORY): Print only after an error or memory
operation.
(SEND ONLY): Print after every fax transmission.
(ERROR ONLY): Print only when an error occurs.
(NEVER PRINT): Never print.
Initial setting: ERROR ONLY
DIAL MODE
This sets the dial mode. Press
(TONE) if you are on a tone
dial line, or
(PULSE) if you are on a pulse dial line.
Initial setting: TONE
PSEUDO RING This sets the duration of the special ringing sound that alerts you
DURATION
to voice calls and manually dialed faxes in TEL/FAX reception
mode. Press a number key as follows:
15 seconds
30 seconds
60 seconds
120 seconds
Initial setting: 15 seconds
DISTINCTIVE
RING
If you subscribe to a distinctive ring service from your phone
company, use this setting to select the ring pattern of the phone
number that you will use as a fax number. For more information,
Initial setting: OFF SETTING
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Option Settings
FAX SIGNAL
RX
The machine will automatically begin reception if you hear a soft
fax tone after answering a call on the machine’s handset or an
extension phone. If you use a computer fax modem to send
documents on the same line, you must turn this function off in
order to prevent the machine from mistakenly attempting to
receive documents from the computer fax modem. Press
(YES) to turn on the the automatic reception function, or
(NO) to turn off the function. If you select NO, you must start
reception manually by pressing
on the machine each time
you hear a soft fax tone after answering a call.
Initial setting: YES
CALLER-ID
If you subscribe to a Caller ID service from your phone company,
use this setting to have the ID of the caller appear in the display
Initial setting: NO
AUTO PRINT
OUT
Press
(YES) to have the machine automatically print an
Activity Report once every 30 send/receive operations. (The
report can still be printed manually at any time.) Press
(NO)
to turn off Auto Print Out.
Initial setting: NO
ECM MODE
Press
(YES) to have any distortions in a transmission due to
noise on the telephone line automatically corrected before print-
out at the receiving end. This is only effective when the other
machine has ECM as well. Press
(NO) to turn off ECM
mode. (When there is considerable noise on the line, you may find
that ECM slows transmission. Turning off ECM mode may
increase transmission speed.)
Initial setting: YES
DAY LIGHT
SAVING
To have the machine’s clock automatically move forward and
backward at the beginning and end of daylight saving time, press
(YES). To turn off this feature, press
Initial setting: NO
(NO).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Settings
LANGUAGE
SELECTION
This sets the language that appears in the display, reports, and
lists. Press for English or for Spanish. A beep will
sound and the display will change to the selected language.
Initial setting: ENGLISH
DIAL TONE
DETECTION
Press
(YES) to have the machine verify the presence of a
dial tone on the line before automatic dialing. Press
turn this function off.
(NO) to
Note: If you select YES and find that the machine is unable to
dial, change the setting to NO.
Initial setting: NO
KEY TONE
Press
(ON) to have the machine sound a beep each time a
key is pressed on the operation panel (this confirms that the key
has been correctly pressed). Press
(OFF) to turn off the
beep sound.
Initial setting: ON
Print Settings
Make a selection for the displayed setting as explained below.
Setting
Description
RECEIVE
RATIO
Press
(AUTO) to have the machine automatically reduce the
size of received faxes to fit the size of the printing paper. This
ensures that the edges of a fax are not cut off. (Note: AUTO may
not operate if the received fax is too long, contains many fine
graphics or images, or is sent at high resolution. In this case, the
remainder of the fax will be printed on a second page.) Press
(100%) to have all faxes printed at full size (if a fax is too
long to fit on the paper, the remainder will be printed on a second
sheet; note that the cut-off point may occur in the middle of a line).
Initial setting: AUTO
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Settings
PAPER SIZE
SORT COPY
This sets the size to which the machine scales received faxes.
Press
(LETTER) if you loaded letter size paper, or
(LEGAL) if you loaded legal size paper.
Initial setting: LETTER
This setting determines whether or not copies are collated (sorted
into sets) when multiple copies of each original page are made.
Press
(YES) to have copies automatically sorted, or
(NO) to have copies grouped by page.
Initial setting: NO
INK SAVE
MODE
To use less ink and speed up ink drying time when printing faxes
and copies, press
(ON) to turn on Ink Save Mode. If you
prefer a higher quality image, press
(OFF) to turn off Ink
Save Mode.
Initial setting: OFF
QUALITY
MODE
To have the machine print higher quality images by printing slowly
when the resolution is set to HALF TONE, press (YES) to
turn on Quality Mode. If you prefer faster printing at the expense of
slightly reduced image quality when using HALF TONE, press
(NO) to turn off Quality Mode.
(Note: This setting does not affect the amount of ink used.)
Initial setting: YES
ALIGN
CARTRIDGE
This is used to align the print cartridge to improve print quality.
CLEAN
NOZZLES
This is used to clean the print cartridge nozzles if print quality is
49
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Printing Lists
You can print lists showing settings and
information entered in the machine.
• GROUP LIST: This shows the
destinations that are stored in the
1 Press FUNCTION , then
until
• SETUP LIST: This shows your
currently entered sender’s name,
sender’s number, and anti-junk fax
number, your current selections for
the option settings, print setup, and
receive faxes to e-mail, and a
sample of the header printed at the
top of every fax page you transmit
(HEADER PRINT).
[LISTING MODE] appears.
2 Press
3 Press
.
or
until the
desired list (see below) appears.
• ACTIVITY LIST: This report shows
information on your most recent
transmissions and receptions
(combined maximum of 30). The
headings are the same as in the
Transaction Report (see the next
section). The logged transactions are
erased after the report is printed. To
have the report print automatically
whenever the number of logged
transactions reaches 30, see page
45 and “AUTO PRINT OUT” on page
47.
• CALLER-ID LIST: This shows
information on your 30 most recently
received calls and faxes (p. 38).
(This list is only available if you are
using the Caller ID function.)
• RECEIVE FAX TO E-MAIL LIST:
This shows the Receive Fax to E-
mail settings that have been stored
(page 41).
• NETWORK SETTING LIST: This
shows the machine’s current IP
address and other network/Internet
settings (page 23).
• DESTINATION LIST: This shows
the fax and e-mail destinations that
have been stored in Rapid Key and
4 Press
to print the list.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Transaction Report
NOTE
One of the following notes
will appear under NOTE to
indicate whether the fax was
successful, and if not, why it
failed.
OK - Transmission/reception
was successful.
P.FAIL - A power failure
prevented the transaction.
JAM - The printing paper or
document jammed.
BUSY - The fax was not sent
because the line was busy.
COM.E-X - (Where “X” is a
number.) A communication
error occurred. See page 56.
CANCEL - The fax was
canceled because the STOP
key was pressed, no
Transaction Report
This report is printed out automatically
after a fax is sent or received to allow
you to check the result. The machine is
initially set to print out the report only
when an error occurs.
♦ The Transaction Report cannot be
printed manually. To change the
condition for automatically printing out
and “TRANSACTION LIST” on page
Headings in the Transaction Report
SENDER/ The name or fax number of
RECEIVER the other machine.
document was in the feeder,
or the other machine
requested a function that
your machine does not have.
START
Starting time.
TX/RX
TIME
Total time taken for
transmission/reception.
PAGES
Number of pages.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
9.Maintenance
• Do not wipe off the grease on the
ends of the white roller.
Cleaning the Machine
• Make sure that all dirt and stains
(such as correcting fluid) are
removed. Dirt and stains will cause
vertical lines on transmitted images
and copies.
Cleaning the scanning glass
and rollers
Any dirt on the scanning glass and
rollers will degrade the quality of
transmitted documents and copies.
Clean these frequently as explained
below.
• If the scanning glass is difficult to
clean, try moistening the cloth with
isopropyl alcohol or denatured
alcohol. Take care that no alcohol
gets on the rollers.
♦ If the document does not feed or
double-feeds occur, use a cloth
moistened with water to wipe the
rollers.
• Do not press down on the two front
rollers.
1 Open the
• Use a cloth moistened with alcohol
to wipe off any splattered ink on the
inside of the compartment or the
underside of the cover. (Do not wipe
the rollers or rubber sheet with the
alcohol-moistened cloth.)
cover.
2 Rotate the lever so that it points
straight up (➊) and pull it up (➋).
4 Replace the white roller, inserting
the left end first. Push the lever
down and rotate it back down.
1
1
2
3 Pull the white roller out to the right.
Wipe the scanning glass, rollers,
and rubber sheet with a clean cloth
2
or swab.
White roller
Scanning
glass
Rollers
Rubber sheet
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Improving Print Quality
5 Close the cover, pressing down
firmly to make sure it clicks into
place.
4 In the page that the machine prints,
locate the line that is closest to a
completely straight line.
Cleaning the housing
In this example, “15” is
closest to a straight line.
Wipe the external parts and surface of
the machine with a dry cloth.
5 Enter the number of the straightest
line with the number keys.
Caution: Do not use benzene or
thinner. These solvents may damage or
discolor the machine.
• To clear a mistake, press
.
6 Press
.
[CLEAN NOZZLES]
Improving Print Quality
Aligning the print cartridge
STOP
7 Press
to exit.
If print quality is not satisfactory, first try
aligning the print cartridge.
Cleaning the print cartridge
nozzles
Note: Make sure that paper is loaded
before beginning this procedure.
If print quality is still not satisfactory
after aligning the print cartridge, clean
the print cartridge nozzles.
1 Press FUNCTION , then
until
[PRINT SET-UP] appears.
1 Press FUNCTION , then
until
2 Press
, then
until
[PRINT SET-UP] appears.
[ALIGN CARTRIDGE] appears.
3 Press
to print an alignment
page. (To enter an alignment value
without printing a page, press
2 Press
, then
until
[CLEAN NOZZLES] appears.
.)
3 Press
.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Improving Print Quality
Wiping the print nozzles and
contacts
• The machine prints a test pattern
similar to the one shown in the
following step.
If you have cleaned the print nozzles as
explained in the previous section at
least three times and print quality is still
not satisfactory, try wiping the print
nozzles and contacts.
4 Compare the diagonal lines above
the printed bars to the diagonal
lines below the printed bars.
• Look for breaks in the diagonal lines
above the bars. Breaks indicate
clogged nozzles.
1 Open the cover and remove the
print cartridge (see the procedure
Breaks in the diagonal lines at the top
of the page indicate clogged nozzles.
• CAUTION! DO NOT touch the gold
contact area of the cartridge or the
contact area of the cartridge holder
with your fingers.
2 Place two or three sheets of paper
on a table or other flat surface.
Moisten a clean, lint-free cloth with
warm water and place the cloth on
the paper.
3 Gently press the nozzles against
the cloth for about three seconds,
and then move the cartridge slowly
in the direction shown to wipe the
nozzles.
Unbroken lines at the bottom of the
page indicate the nozzles were cleaned.
5 If the bottom diagonal lines still
have breaks, repeat Steps 1
through 4 to clean the nozzles
again. Repeat several more times if
necessary.
• If the print quality is still not
satisfactory after cleaning the
nozzles several times, continue with
Step 6.
6 Open the cover and remove and
then reinstall the print cartridge
(see the procedure beginning on
page 9).
4 Using another clean section of the
cloth, repeat the above step.
7 Repeat the nozzle cleaning
procedure. If the lines are still
broken, wipe the nozzles as
explained in the following section.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Improving Print Quality
Cleaning the cartridge holder
5 Moisten another clean cloth with
warm water. Gently hold the cloth
against the contacts for about 3
seconds, and then wipe in the
direction shown.
A dirty print cartridge holder may cause
smudges on your printed pages. To
clean the print cartridge holder, open
the cover and remove the print cartridge
(see the procedure beginning on page
9). Wipe the part indicated below with a
damp cloth.
6 Using another clean section of the
cloth, repeat the above step.
7 Allow the nozzles and contacts to
dry completely.
8 Reinstall the print cartridge and
repeat the nozzle cleaning
procedure as explained in the
previous section.
• If print quality is still not satisfactory
after the nozzles are cleaned,
replace the print cartridge (see page
About the lithium battery:
The machine uses a lithium battery to
retain settings and information
programmed in the machine when
the power is turned off. Battery power
is consumed primarily when the
power is off. With the power kept
continuously off, the life of the battery
is about 5 years. If the battery dies,
have your dealer or retailer replace it.
Do not try to replace it yourself.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Troubleshooting
Problems and Solutions
If you have any problems with the machine, first refer to the following
troubleshooting guide. If you cannot solve the problem, call Sharp's Customer
Assistance Center at 1-877-794-8675.
Line error
Problem
Solution
LINE ERROR appears in
the display.
A line error occurs when your machine cannot
communicate correctly with another fax machine. The
error is usually due to a problem on the phone line.
Try faxing again. If unsuccessful, check the following:
• Check the connection. The cord from the TEL. LINE
jack to the wall jack should be no longer than six feet.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the machine to a different phone line.
• If the error persists, the machine may need service.
Dialing and transmission problems
Problem
Solution
No dial tone when you
pick up the handset or
press the SPEAKER key.
• Make sure the handset cord is connected to the
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
• Make sure that the telephone line is good.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Dialing is not possible.
• Make sure the power cord is properly plugged into a
power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
• Make sure that the machine is set to the correct
dialing mode for your telephone line. See the
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Check the display for error messages.
• Pick up the handset and check for a dial tone. Dial the
receiving machine manually and make sure that it is
responding (you should hear a fax tone).
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion. Try
sending the document again.
• Make a copy of the document on your machine. If the
copy is also distorted, your machine may need
service.
Reception and copying problems
Problem
Solution
The machine doesn't
receive documents
automatically.
• Make sure that the reception mode is set to AUTO. If
you subscribe to a distinctive ring service, make sure
that the Distinctive Ring function is set to the correct
ring pattern. If you do not subscribe to a distinctive
ring service, make sure that Distinctive Ring is set to
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
The printing paper comes • Make sure that the document is loaded properly in the
out blank when you try to
receive a document.
feeder of the transmitting machine. Make a copy or
print a report to confirm the printing ability of your
machine.
Print quality is poor.
• The print cartridge may need alignment or cleaning.
The received document is • Ask the other party to send higher contrast
faint.
documents.
• The print cartridge may need replacement. Make a
copy or print a report to check your machine’s printing
ability.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document again.
• Make a copy or print a report on your machine. If the
copy or report is also distorted, your machine may
need service.
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will cause
spots to appear on copies and transmitted faxes.
Clean the scanning glass as explained on page 52.
General problems
Problem
Solution
Nothing appears in the
display.
• Make sure the power cord is properly plugged into a
power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the keys,
unplug the power cord and then plug it in again
several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Messages and Signals
Display messages
messages related to Caller ID.
ADD PAPER & /
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add paper
and then press . If there is paper in the tray, make
sure it is inserted correctly (take out the stack, align the
edges evenly, and then reinsert it in the tray) and then
press
.
CHANGE CARTRIDGE
CHECK CARTRIDGE
CONNECTION ERROR
This message appears after you install or replace the
The print cartridge is missing and must be installed, or
is not installed correctly.
A Fax to E-mail transmission was not successful
because of a communication problem on your local
network. This is usually due to a problem with the cable
connections. Make sure that the cable ends are
securely inserted in the LAN ports. Make sure that the
correct cable is being used and that the cable is good.
Make sure that your router or hub is powered on.
CHECK E-MAIL SETTING Fax to E-mail transmission is not possible because the
SMTP server or the sender address has not been
DOCUMENT JAMMED
The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will occur
if you load more than 20 pages at once or load
document may also jam if the receiving machine doesn’t
respond properly when you attempt to send a fax.
FAX RX IN MEMORY
A fax has been received in memory because the print
cartridge needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will print
out automatically when the problem is fixed.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
INK NEAR EMPTY
LINE ERROR
The cartridge is nearly empty (approximately one eighth
of the ink remains).
Transmission or reception was not successful. Press
STOP
to clear the message and then try again. If the error
LOW INK
The cartridge is low on ink (approximately one quarter
of the ink remains).
MEMORY FULL
If faxes have been received to memory because printing
is not possible, resolve the problem so that printing can
If faxes are being held in memory because the Secure
Receive function has been activated, print the faxes as
explained on page 43.
If you are attempting to broadcast or transmit from
If you are copying, see If MEMORY FULL appears on
OUT OF INK
The cartridge is out of ink and must be replaced. Faxes
will be received to memory.
PAPER JAMMED
PRINTER ERROR
The printing paper is jammed. See page 62.
A printer error has occurred. Open the cover, make sure
the print cartridge is installed correctly, and then close
the cover.
PRINTER ERROR/
CHECK PAPER
A paper jam may have occurred. Follow the procedure
RECALLING
This appears if you attempt to send a fax by auto dialing
and the line is busy or the receiving fax machine does
not answer. Your machine will automatically reattempt
RECEIVED SECURE FAX A received fax is being held in memory because the
Secure Receive function has been activated. Enter your
secure code to print the fax (see page 43).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
SERVER ERROR
A Fax to E-mail transmission was not successful
because the machine could not connect to your mail
server or there was no response from the mail server.
you have configured “POP before SMTP” settings in the
Web pages, make sure these settings are correct. If
[CABLE DISCONNECTED] appears on the bottom line,
see “CONNECTION ERROR” on page 59.
SERVER NOT FOUND/
CABLE DISCONNECTED
SERVER NOT FOUND/
DHCP
A Fax to E-mail transmission was not successful
because the machine was unable to automatically obtain
an IP address. Restart your router or other device that
acts as your DHCP server.
SERVER NOT FOUND/
SMTP
A Fax to E-mail transmission was not successful
because an incorrect host name is entered for your
SMTP server. Check the SMTP server setting (p. 18).
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
2 Replace the white roller, inserting
the left end first. Push the lever
down and rotate it back down
(➊).Close the cover, pressing firmly
on both front corners (➋).
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed
properly during transmission or copying,
or [DOCUMENT JAMMED] appears in
2
the display, first try pressing
. If
the document doesn't feed out, remove
it as explained below.
Important: Do not try to remove a
jammed document without releasing it
as explained below. This may damage
the feeder mechanism.
1
1 Open the cover (➊). Rotate the lever
so that points straight up (➋), and
pull it up (➌). Pull the roller out to the
right, and remove the document (➍).
Clearing jammed printing paper
1 Open the cover (➊). Pull the
jammed paper forward or backward
out of the machine as appropriate
(➋), taking care not to tear it.
2
1
4
1
2
2
3
2 Close the cover, pressing down
firmly on both front corners.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Parts
Ordering Parts
To order parts, contact the parts distribution center located nearest you.
When ordering a part, use the part order number shown below.
Operation manual
Setup Guide
TINSE4521XHTB
TCADH3894XHZZ
QCNWG202DXHFW
QCNWG370BXHZZ
DUNTK245DXHPW
LPLTP3435XHSA
LPLTP3434XHSA
LPLTP3442XHSA
TLABH415KXHSA
Handset cord
Telephone line cord
Handset
Paper tray
Document exit tray
Received document tray
Rapid Key labels
Part distribution centers
Tritronics, Inc.
1306 Continental Drive
Abingdon, MD 21009
Tel: 1-800-638-3328
Fax: 1-800-888-FAXD
Tritronics, Inc.
Tel:1-800-365-8030
1015 NW 52nd Street
Ft. Lauderdale, FL 33309
Fax: 1-800-999-FAXD
Fox International, Ltd.
23600 Aurora Road
Tel: 1-800-321-6993
Fax: 1-800-445-7991
Bedford Heights, OH 44146
Andrews Electronics
25158 Avenue Stanford
Santa Clarita, CA 91355
Tel: 1-800-274-4666
Fax: 1-805-295-5126
Sharp Accessories and
Supply Center
Tel: 1-800-642-2122
2130 Townline Road
Peoria, IL 61615
63
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the rear of this equipment is a label that contains, among other information, a product
identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the
telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
details. This equipment connects to the telephone network through a standard USOC RJ-11C
network interface jack.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local telephone company. For products approved after July 23, 2001, the REN
for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The
digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information, please contact
Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If the equipment is
causing harm to the telephone network, the telephone company may request that you disconnect
the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment ID does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
This equipment is hearing-aid compatible.
When programming and/or making test calls to emergency numbers:
♦ Remain on the line and briefly explain to the dispatcher the reason for the call.
♦ Perform such activities in the off-peak hours, such as early morning or late evening.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Date Revised:
Date Issued: Apr. 25. 2006
.
MATERIAL SAFETY DATA SHEET (1/3)
MSDS No. B-1029
Section 1. Product and Company Identification
Product Name : Ink cartridge of UX-C80B
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
(Area)
North
(Country)
U.S.A.
(Name and Telephone Number)
Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
America
Emergency telephone number :
1-800-255-3924
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number :
1-800-255-3924
Section 2. Ingredients
Ingredients
Carbon Black
Cas No.
Proportion
1-5
OSHA PEL
ACGIH TLV
3
3
1333-86-4
3.5 mg/m TWA 3.5 mg/m TWA
Trade
Acrylic Terpolymer
0.1-2
None
None
None
None
Secret(#)
Trade
Secret(#)
Water Soluble Organic Solvents
10-20
Hydroxylated Alkane
NJTSRN 80100451-5004
Water
Trade
1-10
None
None
None
None
Secret(#)
7732-18-5
60-78
# : Supplier's confidential information
Section 3. Hazardous Identification
The following information from our supplier is based on testing of the product as a whole and/or characteristics
of components.
Hazard Information : Primary Routes of Exposure: Ingestion, skin contact.
Inhalation :
If ink mist is inhaled, respiratory tract irritation may occur. Exposure not probable with
intended use.
No adverse chronic effects known at intended level of use.
Skin Contact :
Eye Contact :
Ingestion :
Not an irritant. Exposure not probable with intended use. Not a dermal sensitizer.
Not an irritant. Exposure not probable with intended use.
Low acute oral toxicity. Exposure not probable with intended use.
Section 4. First-Aid Measures
Inhalation: If symptoms, such as shortness of breath or persistent coughing are experienced, remove source
of contamination and move individual to fresh air. If symptoms persist, seek medical attention.
Skin Contact: Wash with soap and water. Should irritation occur, seek medical attention.
Eye Contact: Flush immediately with plenty of water. Remove contact lenses and continue flushing for at
least 15 minutes.
If irritation develops and persists, seek medical attention.
Ingestion: Immediately wash mouth out with plenty of water. Do not induce vomiting. Slowly dilute with 1-2 glasses
of water or milk and seek medical attention. Never give anything by mouth to an unconscious person.
Aggravated Conditions : None known
Notes to Physician :
No specific antidote.
Section 5. Fire-Fighting Measures
°
Flash Point/Range ( C) :
Not applicable
°
Autoignition Temperature ( C) :
Flammable Limits in Air UEL :
Flammable Limits in Air LEL :
Extinguishing Media :
Hazardous Combustion Products : Carbon monoxide, carbon dioxide, unidentified organics
Special Exposure Hazards :
Special Protective Equipment :
Not determined
Not determined
Not determined
Carbon dioxide, water spray or fog, dry chemical or foam
None known
NIOSH approved self contained breathing apparatus may be required
if a large number of cartridges are involved.
Health: 1 Flammability: 0 Reactivity: 0
Health: 1 Flammability: 0 Reactivity: 0
NFPA Rating :
HMIS Classification :
65
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Date Revised:
Date Issued: :Apr. 25. 2006
.
MATERIAL SAFETY DATA SHEET (2/3)
MSDS No. B-1029
Section 6. Accidental Release Measures
Personal Precautionary Measures :
Environmental Precautionary :
None required for intended use in printer.
Unless specifically permitted for disposal, keep waste out of sewers,
watersheds, and waterways.
Procedure for Cleaning/ Absorption : Absorb small spills with cloth or paper towels or other suitable
material. Place in container for disposal. For large spills, dike
around spill with absorbent material. Wash spill site with soap and
water after material pickup is complete. Disposal is subject to
federal, state, local, or provincial regulations.
Section 7. Handling and Storage
Handling : To avoid damage to cartridge and accidental contact with ink
KEEP OUT OF REACH OF CHILDREN.
Storage : Store in a cool, dry place.
Section 8. Exposure Control/Personal Protection
Engineering Controls :
None required.
Respiratory Protection : None required for intended use in printer.
Gloves :
Skin Protection :
Eyes :
None required for intended use in printer.
None required for intended use in printer.
None required for intended use in printer.
Section 9. Physical and Chemical Properties
Physical State:
Color :
Odor:
Cartridge contains liquid ink
Black
Faint
Pressurized:
pH:
Specific Gravity: Approx. 1.0
No
7.0-8.5
Solubility in Water: Fully Miscible
Specific Gravity: Approx. 1.0
Section 10. Stability and Reactivity
Chemical Stability :
Stable
Hazardous Polymerization :
Conditions to Avoid :
Materials to Avoid :
Will not occur
None known
None known
Hazardous Decomposition Products :
Additional Guidelines :
Carbon monoxide, carbon dioxide, unidentified organics
None
Section 11. Toxicological Information
Primary Routes of Exposure : Ingestion, skin contact.
Ingestion : Low acute oral toxicity. Exposure not probable with intended use. Based on component
characteristics, gastrointestinal, liver, kidney, and CNS effects are possible if large quantities of
ink are ingested.
Acute Toxicity Oral Rat LD50(mg/kg) : >2000
Inhalation : Low acute inhalation toxicity. Pure carbon black, a minor component of this product, has been
listed by IARC as a group 2B (possible carcinogen). This classification is based on rat "lung
particulate overload" studies performed with airborne particulate carbon black. Toner is not
listed by IARC, NTP, or OSHA.
Aggravated Conditions :
None known
Carcinogenicity Comment : Neither this product nor any of its components present above 0.1% are listed
by IARC, NTP, or OSHA as known carcinogens.
Section 12. Ecological Information
Mobility :
Persistence :
Bioaccumulative :
Not determined
Not determined
Not determined
Other Information : None
66
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Date Revised:
Date Issued: :Apr. 25. 2006
.
MATERIAL SAFETY DATA SHEET (3/3)
MSDS No. B-1029
Section 13. Disposal Consideration
Waste Disposal:
This product is not a listed hazardous waste in accordance with Federal Regulation 40 CFR Part 261. If
discarded in its purchased form, this product would not be a hazardous waste either by listing or by
characteristic. However, under RCRA, it is the responsibility of the product user to determine at the time of
disposal whether a material has been contaminated and should be classified as a hazardous waste. Disposal
is subject to local, state and federal regulations.
Section 14. Transport Information
DOT Status :
DOT Shipping Name : Not applicable
Hazard Class : Not applicable
Not classified as a hazardous material or substance under US DOT.
DOT Reportable Quantity : Not applicable
DOT Packing Group : Not applicable
Section 15. Regulatory Information
TSCA (USA) All ingredients are listed on the Toxic Substances Control Act (TSCA) inventory, have been
registered, or are exempt.
SARA / EPCRA (USA) :
None of the ingredients in this product has a final reportable quantity (RQ) under
Emergency Planning and Community Right-to Know Act (EPCRA)- Section 302
: Extremely Hazardous Substances (EHS) or notification requirements for EHS
under Section 304.
California Proposition 65 : This product contains no known materials at levels which the State of California
has found to cause cancer, birth defects or other reproductive harm - California
Proposition 65.
DSL (Canada) :
All ingredients are listed on the Canadian Domestic Substances List (DSL), have been
registered on the Non-Domestic Substances List (NDSL), or are exempt.
EINECS (Europe) : All ingredients are listed on the European Inventory of Existing Commercial Substances
(EINECS) list, have been registered on the European List of New Chemical Substances
(ELINCS), or are exempt.
ENCS (Japan) :
All ingredients are listed on the Japanese Existing and New Chemical Substances
(ENCS) list,have been registered, or are exempt.
AICS (Australia) : All ingredients are listed in Australian Inventory of Commercial Substances (AICS), or
are registered in Australia.
ECL (Korea) :
All ingredients are listed on the Korean Existing Chemicals List (ECL), have been
registered, or are exempt.
WHMIS Hazard Class (Canada) : Not a WHMIS controlled product.
Section 16. Other Information
Reference :
IARC(1996): IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to
Humans, Vol. 65, Printing Process and Printing Inks, Carbon Black and Some Nitro Compounds,
Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie,
P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation
Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
Restrictions :
This information relates only to the specific material designated as supplied by the manufacturer.
This information is supplied to us by the manufacturer and Sharp offers no warranties as to its
accuracy and accepts no responsibilities for any typographical errors which may appear on these
sheets. The information on this data sheet represents best opinion as to the proper use in handling
of this product under normal conditions. However, all materials may present unknown hazards and
should be used with caution. Although certain hazards are described herein, we do not guarantee
that these are the only hazards which exist. It is the responsibility of the user to determine the
suitability of this product for each particular use.
Revision Information :
2006/Apr./25 Not applicable in this time due to new issue.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Reference Guide
Fax / Fax to E-mail Transmission
Receiving Faxes
Place your document (up to 20 pages)
face down in the document feeder.
RESOLUTION/
RECEPTION MODE
Press
until the desired
reception mode appears in the display.
AUTO mode: The machine
automatically answers and receives
faxes.
2
1
MANUAL mode: Answer all calls (even
faxes) by picking up the handset. To
Sending a Fax by Normal Dialing
SPEAKER
begin fax reception, press
.
1 Lift the handset or press
.
TEL/FAX mode: The machine
2 Dial the fax number.
automatically answers and receives
faxes. Voice calls are signalled by a
special ringing sound.
3 Wait for the reception tone (if a
person answers, ask them to press
their Start key).
Storing Destinations
FUNCTION
4 Press
.
1 Press
,
, then
.
Using a Rapid Key (fax/e-mail)
2 Press an unused Rapid Key, or
Press the Rapid Key for the destination.
SPEED DIAL
press
and enter an unused
Using a Speed Dial number
(fax/e-mail)
2-digit Speed Dial number (01 to
63). (For an e-mail destination, you
can also press the A, B or C key
and go to Step 4.)
SPEED DIAL
1 Press
3 Press
for fax or
for e-
2 Enter the appropriate 2-digit Speed
mail.
Dial number and press
.
4 Enter the fax number or the e-mail
address.
Searching for a destination
(fax/e-mail)
5 Press
.
1 Press
or
until the
6 Enter a name with the letter keys.
desired destination appears.
STOP
7 Press
and then
.
2 Press
68
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Guía de referencia rápida
Transmisión de Fax / de Fax a correo
electrónico
Cómo recibir faxes
RESOLUTION/
RECEPTION MODE
Coloque el documento (hasta 20 páginas)
mirando hacia abajo en el alimentador.
Oprima
hasta que aparezca el
modo de recepción deseado en el display.
Modo AUTO: El contestador
automáticamente contesta las llamadas y
recibe faxes.
2
1
Modo MANUAL: Contesta todas las
llamadas (incluso las de telefax)
levantando el auricular. Para que
comience la recepción del documento,
Cómo enviar un fax por marcación
normal
SPEAKER
oprima
.
1 Levante el auricular u oprima
.
Modo TEL/FAX: El contestador
2 Marque el número de fax.
automáticamente contesta las llamadas y
recibe faxes. Las llamadas de voz se
indican con un sonido de timbre especial.
3 Espere a escuchar el tono de
recepción (si alguien contesta el
teléfono, pídale que oprima la tecla
Start).
Cómo programar números
FUNCTION
1 Oprima
,
, y a
4 Oprima
.
continuación
.
Cómo utilizar la Tecla rápida (fax/
correo electrónico)
2 Oprima una tecla rápida no utilizada,
Oprima la Tecla rápida para el número
deseado.
SPEED DIAL
u oprima
e introduzca un
Cómo utilizar un número de Marcación
abreviada
número de marcación abreviada de 2
dígitos no utilizado (01a 63). (Para
programar una dirección de correo
electrónico, también puede oprimir las
teclas A, B o C y continuar en el Paso
4.)
(fax/correo electrónico)
SPEED DIAL
1 Oprima
.
2 Introduzca el número de 2 dígitos de
3 Oprima
para fax o
correo electrónico.
para
marcación abreviada apropiado y
oprima
.
4 Introduzca el número de fax o la
dirección de correo electrónico.
Cómo buscar un número
(fax/correo electrónico)
5 Oprima
.
6 Introduzca un nombre con las teclas
1 Oprima
o
hasta que
de letras.
aparezca el número deseado.
STOP
7 Oprima
y a continuación
.
2 Oprima
.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
I
Index
A
E
Anti Junk Fax, 40
ECM mode (Error Correction Mode), 47
E-mail addresses, storing, 19
E-mail options, 21
Audible signals, 61
Auto Print Out (of Activity Report), 47
Auto-dial numbers
Storing, 27
F
B
Fax Signal Receive, 47
Fax to E-mail transmission, 20
Batch page numbering, 31
Broadcasting, 35
File name, 22
Fine Priority setting, 45
C
Caller ID, 37
G
Copies, 34
Group Keys, storing, 36
Group keys, using, 36
Group List, 50
D
H
Date, setting, 12
Day Light Saving setting, 47
Destination List, 50
Dial Mode, 46
Halftone setting, 25
Handset, 7
Handset receiver volume, 13
Hold, 33
Housing, cleaning, 53
Dial tone detection, 48
Dialing
Automatic redialing, 30
Direct Keypad, 30
Rapid Key, 29
Redialing, 30
I
Ink Save Mode, 49
Search, 29
Speed, 29
J
Jams, clearing, 62
Direct Keypad Dialing, 30
Document feeder, 24
Document restrictions, 24
Document sizes, 24
Duplex Scan, 40
K
Key Tone setting, 48
L
Language setting, 48
Letters, entering, 6
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Line error, 56
Loading paper, 8
R
Rapid Key Dialing, 29
Rapid Key, using for e-mail, 21
Receive Fax to E-mail, 41
Receive Fax to E-mail List, 50
Reception mode
Loading the document, 24
M
Memory full, 60
Memory, substitute reception to, 33
Redialing, 30
Redialing, automatic, 30
Removing original document, 25
Resolution, 25
N
Network
Cable, 14
Checking connection, 15
Connecting to, 14
Ringer volume, 13
Problems, 16
Network Setting List, 50
Network settings, configuring, 23
Network settings, initializing, 23
Normal Dialing, 26
S
Scanning glass, cleaning, 52
Search Dialing, 29
Number of Rings setting, 45
Searching for stored e-mail address, 21
Secure Receive, 43
Sender address, 18
Sender name, 18
Sender’s name and fax number,
entering, 11
Setup List, 50
O
Ordering parts, 63
P
Packing tape, removing, 7
Page numbering, batch, 31
Paper jams, clearing, 62
Paper size setting, 49
Paper, loading, 8
SMTP server, 18
Sort Copy, 49
Speed Dial number, using for e-mail, 21
Speed Dialing, 29
Power cord, 9
Print cartridge
T
Aligning, 53
TEL. LINE jack, 11
Cleaning nozzles, 53
Installing, 9
Wiping nozzles, 54
Print cartridge holder, wiping, 55
Pseudo Ring, 46
Telephone line cord, 11
Time, setting, 12
Transaction Report, 51
Setting print condition, 46
Q
V
Quality Mode setting, 49
Voice calls, 29
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
W
Web page in machine, 17
72
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under appli-
cable state law, implied warranties may not validly be disclaimed or excluded, the duration of such
implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product:
Personal Facsimile
Warranty Period for this Product:
Additional items excluded
from warranty coverage:
Where to obtain service:
Ninety (90) days parts and labor from date of purchase.
Any consumable items such as paper supplied with the
Product.
At a Sharp Authorized Servicer located in the United States.
To find out the location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-877-794-8675.
What to do to obtain service:
Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer.
Be sure to have proof of purchase available. If you ship or mail the
Product, be sure it is packaged carefully.
World Wide Web or call 1-877-794-8675.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-1163
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163
SHARP CORPORATION
FOR YOUR RECORDS
Please record the model number and serial number below, for easy
reference, in case of loss or theft. These numbers are located on the
rear side of the unit.Space is also provided for other relevant
information.
UX-B800SE
Model Number
Serial Number
Date of Purchase
Place of Purchase
PRINTED IN THAILAND
(TINSE4521XHTB)
Download from Www.Somanuals.com. All Manuals Search And Download.
|