OWNER’S MANUAL
Model GI477/GI477R
120V., 60 Hz., 1500 Watts
EURO-PRO Operating LLC
U.S.: 94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Canadá : 4400, Bois-Franc
St-Laurent, QC H4S 1A7
Tel. : 1 (800) 798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
GETTING TO KNOW YOUR ELECTRONIC IRON
The odor is safe and should not reoccur
after initial heating.
Before using your Retractor ™
Retractable Cord Iron, remove any
labels, stickers or tags that may be
attached to the body or soleplate of the
iron.
When turned on for the first time, your
new iron may emit an odor for up to 10
minutes. This is due to the initial
heating of the materials used in making
the iron.
PROBLEM
POSSIBLE REASONS & SOLUTIONS
• Iron should be plugged into a 120V AC electrical
outlet only.
Make sure that the plug is securely in the socket.
• Temperature setting too low.
Select a higher fabric setting.
Also, before ironing with steam for the
first time, allow iron to heat, hold in a
horizontal position and hit the burst of
steam button several times. The iron
may emit some small particles from the
steam holes. This is normal and will
clear after pressing the burst of steam
button several times.
Iron does not heat
• This is normal.
Some odor or small
particles come out of
steam vents of new
iron
Follow instructions for first use and allow iron to steam
through 2-3 fillings & press the steam burst button
occasionally to eliminate small white particles.
Display Panel
• Water tank may be empty or water level is very low.
Add water.
Iron does not steam
• Make sure that the fabric/temperature setting and
the variable steam control are correctly set. For
maximum steam, (setting ‘Max’ on steam control),
temperature setting should be set on ‘•••’.
• Variable steam control dial is set on “0”.
Always allow the iron to reach the selected
temperature with the variable steam control setting
at ‘0’. Make sure the temperature setting is set in
the correct steam area, e.g. ‘•’, and the steam control is
not on ‘0’. For more steam, set the fabric setting to a
higher setting, e.g. ‘•••’, and the steam control to ‘Max’.
• If temperature setting and steam control setting are
correct and there is no steam, gently tap the
soleplate on the ironing board a few times. Move
the variable steam control from ‘0’ to ‘Max’ a few
times.
14
15
13
12
9. Stainless Steel Soleplate
10. Cord Rewind Button
11. Handle
12. Auto-Shut-Off
13. Power On Light
14. Fabric Settings
15. Temperature & Steam
Indicators
1. Electronic Temperature Control
2. Atomizer Spray Button
3. Burst of Steam
4. Variable Steam Control
5. Water Inlet Cover
6. Spray Nozzle
7. Water Level Window
8. Display Panel
• Iron may not be hot enough. Set temperature to the
‘Max’ position. Always allow iron sufficient time to
heat up before activating the variable steam control.
• Overuse of steam burst. Allow more time between
each burst.
• Iron may have been overfilled. Turn iron off,empty
water and follow instructions for filling.
• Steam performance may be low if iron requires
seasoning. To season, use regular tap water for 1or 2
tanks until steam performance improves.
Water droplets coming
from steam vents
16. Water Flask
Technical Specifications
Voltage:
Power:
120V, 60 Hz
1500 Watts
*Illustrations may differ from actual product
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF SHARK RETRACTORTM IRON
IRONING CHART
LED Display Panel
3
NOTE: Always refer to the garment care tag for ironing instructions. Before starting to
iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an
inside seam.
1
2
DIRECTIONS
ON LABEL
SYNTHETIC
FIBERS, e.g.
1. Burst of Steam Button
Burst of steam provides extra,
sudden bursts of steam which aid in
removing stubborn wrinkles from
fabrics such as denim, cotton or
linen.
SILK
COTTON
LINEN
acrylic, nylon
polyester
FABRIC
WOOL
7. Led Display Panel
Displays the fabric setting
(left) and the temperature
indicators (right).
2. Atomizer Spray Button
Pressing this button provides a
defined jet of spray which gently
moistens fabric.
LED
DISPLAY
PANEL
MIN
MAX
• • • • •
•
3. Variable Steam Control
Minimum to maximum steaming
for different materials. Self
cleaning feature flushes internal
sole plate with water.
MAXIMUM
STEAM
STEAM
CONTROL
0
0
8. Water Filling Inlet
The cover prevents dust and
foreign matter from entering
the water tank. It also stops
any water from spilling during
ironing.
4. Anti-Drip Function
Cuts off water when the
iron temperature is too
low.
BURST OF
STEAM
5. Built-In Anti-Calcium Filter
Prevents calcium build-up
and prolongs the life of the
iron.
6. Stainless Steel Soleplate
Provides maximum glide-
ability and heat retention.
SPRAY
9.
Cord
The power cord is easily
stored inside the iron using
the cord rewind button.
CAUTION: Always hold the plug
when rewinding the power cord.
Do not allow plug to whip when
rewinding.
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Emptying the Iron
This appliance is for HOUSEHOLD USE
Note: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
1. Always empty iron after each use.
2. When finished using the iron, turn the
variable steam control to “0” and press
the electronic temperature control button
until the power light is lit.
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
Fabric & Temperature Indicators
Press on the Electronic Temperature
Control to select the desired fabric
setting. The red lights at the left of the
LED Display Panel will light up.
At the same time, the temperature
indicator lights on the right side of the
LED Display Panel will start to flash.
They will stop flashing when the iron
reaches the selected temperature.
WARNING: Never fill the iron with
fabric conditioner, starches or any
other liquid, as these will damage the
steam mechanism. Do not use
contaminated water.
3. Unplug the iron from the electrical outlet.
4. Turn the iron upside down over the
sink with the tip pointing downward
and allow the water to flow from the
opening.
5. Place iron upright and allow to cool
before storing.
Fig. 7
Storage
1. Always turn the variable steam control
to “0” after you have emptied the water
tank.
2. Allow the iron to cool down.
3. Always store the iron in the upright
position to protect the soleplate.
4. From time to time, clean the exterior
of the iron with a damp cloth and wipe
dry.
5. If you use spray starch, wipe the
soleplate occasionally with a soft
damp cloth to prevent the build-up of
deposits.
6. If the iron has not been used for a few
weeks, hold the iron horizontally and
allow to steam for 2 minutes before
ironing.
7. The iron is equipped with a retractable
cord. Press the cord rewind button to
engage cord storage. (Fig. 8) If the
cord does not fully retract, pull it out
again and then press on cord rewind
button.
CAUTION: Always hold the plug when
rewinding the power cord. Do not allow
plug to whip when rewinding.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. (Fig. 1) Fill tank to
CAUTION: Use caution when
emptying the iron. Burns may occur
from touching hot metal surfaces,
hot water or steam.
desired level or to the “MAX” water
level marking using the water filling
flask. (When the iron is upright, the
see-through water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank. When finished
filling the iron with water, close the
water inlet cover before continuing.
Dry Ironing
For dry ironing, slide the variable steam
control all the way to the left to “0”. This
will cut off the steam flow if water is in
the water tank. All marked fabric
settings on the LED Display Panel can
be used for dry ironing.
Self Cleaning
It is important to “Self Clean” the iron at
least every two weeks to remove scale,
calcium, etc. The harder the water, the
more often the iron should be self
cleaned.
1. Plug the cord into a polarized, 120V
AC electrical outlet. The power “ON”
light will come on, indicating that the
iron is receiving power.
2. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control to “0”.
(See “Ironing Guide” for a guide to
temperature selection.)
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.
1. Set the variable steam control to
any steam position.
2. Fill the water tank up to the “MAX”
level.
3. Stand the iron on its heel. Plug the
iron into the electrical outlet.
4. Press the electronic temperature
control button until you get the
“MAX” temperature setting on the
display panel and wait until the iron
heats up and temperature setting
light stops flashing. (Fig. 7)
5. Turn the variable steam control all
the way to the right to the self-
cleaning position and hold the iron
horizontally over the sink. (Fig. 7)
6. Boiling water and steam will now be
ejected from the holes in the
soleplate. The impurities and scale
are washed away with it.
7. Move the iron back and forth as this
happens.
8. If there is any water left in the water
tank after the iron stops steaming,
just empty the remaining water in a
sink following the instructions for
emptying the iron.
Fig. 1
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to
the desired steam setting. (See
“Ironing Guide” for a guide to
temperature selection.)
Steam Ironing
Cord Rewind
Button
CAUTION DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
WARNING Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
Fig. 8
Note: The anti-drip function reduces
water dripping and water stains. It does
not prevent water dripping and water
stains if you press the steam burst button
too often or if the temperature is too low.
The amount of water droplets will
CAUTION TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
9. Turn the variable steam control to
the “0” position when the water tank
is empty.
10.Place the iron back upright on its
heel to cool down before storing.
eventually decrease after the iron is used
for 2 to 3 tankfuls of steaming and ironing.
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
4. Place the iron on its heel on a stable,
Selecting Iron Temperatures
Ironing Hints
protected surface and allow the iron
to heat for approximately two (2)
minutes or until the temperature
settings on the right side of the LED
display panel have stopped flashing.
5. Turn the variable steam control dial
to the right to increase the amount of
steam. When using extra steam, the
iron uses more water and it may be
necessary to fill the water tank more
often. (Fig. 2)
Always read garment labels and follow
the manufacturer’s ironing instructions.
Refer to the “Ironing Chart” for
WARNING: To prevent fire, do not
leave iron unattended while
connected.
Slide
temperature recommendations:
• Sort articles to be ironed according
to the type of fabric. This will reduce
the need to adjust the temperature
for different types of garments.
• If you are not sure of the fiber content
of a garment, test fabric by ironing a
small area such as a seam or inside
hem section before ironing a visible
area. Start with a low temperature
setting and gradually increase to find
the best setting.
• When reducing the temperature to
iron sensitive fabrics, allow
approximately 2 minutes for the iron
to cool to the new temperature
setting.
•
Use low settings for nylon and other
synthetics.
•• Use moderate settings for wool,
silks, and blends.
••• Use high settings for cottons and
linens.
1. Stand the iron upright on its heel.
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press the electronic temperature
control until you get the desired
fabric/temperature setting.
4. The light on the right side of the LED
display panel will stop flashing when
the desired temperature has been
reached. (Fig. 5)
Fig. 3
5. Slide the variable steam control
up to increase the amount of
steam. (Fig. 3) When using extra
steam, the iron uses more water
and it may be necessary to fill
the tank more often. See page 4
for refilling the iron with water.
6. Steam is produced as soon as
the iron is held in the horizontal
position. Steam will stop coming
out when the iron is put on its
heel in a vertical position or by
setting the variable steam control
to “0”.
• Fabrics such as velour, wool, linen
and silk are best ironed with an
ironing cloth to prevent shine marks.
Fig. 2
Burst of Steam Button
Auto Shut-Off
CAUTION: DO NOT aim iron at
face, towards yourself, or anyone
else while using or adjusting steam.
Burns or serious injury may occur.
The Retractor™ retractable cord iron is
equipped with an auto shut-off. The auto
shut-off switches the iron off if it has been
left standing unmoved in any position
(sideways, flat or upright) for
approximately 7 minutes. A red light on
the LED display panel will flash when the
iron switches itself off. (Fig. 6) To switch
the iron back on, just shake the iron side-
to-side several times, the iron will turn
back on at the lowest temperature setting,
regardless of the initial temperature
setting. Reset to the desired temperature
before continuing.
Atomizer Spray Nozzle
The burst of steam position is useful
when ironing denim, cotton and linens. It
provides quick bursts of steam which
aid in removing stubborn wrinkles.
The atomizer spray nozzle is useful on
fabrics with stubborn wrinkles. Press the
spray button and a jet of water will spray
onto the fabric being ironed. (Fig. 4) The
water spray can be used with dry or
steam ironing as desired.
Temp.
settings
The burst of steam feature can be used
with Dry or Steam ironing as desired.
1. Make sure the water tank is at least
1/2 filled with water.
2. Select the desired fabric and
temperature setting. Place the iron
on its heel (on a stable, protected
surface) and allow it to heat for
approximately 2 minutes.
Fig. 5
3. Position variable steam control to the
burst of steam position. (Fig. 3)
4. With the iron in a horizontal position,
press the steam button several times
to prime the pump.
Fig. 4
Flash
Fig. 6
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|