AOC-R1UG-IBQ Add-on Card
User’s Guide
Revison 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 Safety Guidelines ..........................................................1-1
1-1 ESD Safety Guidelines.....................................................................1-1
1-2 General Safety Guidelines...............................................................1-1
1-3 An Important Note to Users.............................................................1-1
Chapter 2 Card Components.........................................................2-1
2-1 Front Components ............................................................................2-1
2-2 Front Connectors, Jumpers and LEDs ..........................................2-1
QSFP Port...............................................................................................2-1
LEDs .......................................................................................................2-1
J1 Jumper ...............................................................................................2-2
J2 Jumper ...............................................................................................2-2
Chapter 3 Installation.........................................................................3-1
3-1 Hardware Installation........................................................................3-1
Before Installation ...................................................................................3-1
Installation...............................................................................................3-1
3-2 Installing Drivers and Firmware ......................................................3-2
Linux Drivers...........................................................................................3-2
Windows Drivers.....................................................................................3-2
Firmware Update Procedures.................................................................3-3
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Guide
Notes
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
This manual is written for system integrators, PC technicians and knowledgeable PC
users who intend to integrate SuperMicro's AOC-R1UG-IBQ add-on card to their
system. This add-on card is used to add an InfiniBand port to the H8DGG-QF
serverboard.
Product Features
The AOC-R1UG-IBQ add-on card offers the following features:
•
•
•
•
•
•
•
•
•
•
Mellanox® ConnectX-2 QDR
Single QSFP connector
40Gb/s per port
1us MPI ping latency
CPU off-load of transport operations
End-to-end QoS and congestion control
Hardware-based I/O virtualization
TCP/UDP/IP stateless off-load
External optical media adapter and active cable support
Dimensions: 12.79” (32.48cm) x 8.66” (22cm) (length x width)
of supported platforms.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Guide
Operating Systems Supported
The AOC-R1UG-IBQ add-on card supports the following Operating Systems (OS):
•
•
•
•
•
•
Windows 2003/Windows 2008
VMware ESX Server 3.5
SLES
RedHat
Fedora
CCS 2003
An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest revision
available at the time of publishing. The card you have received may or may not look
exactly the same as the graphics shown in this manual.
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before
any warranty service will be rendered. You can obtain service by calling your vendor for
a Returned Merchandise Authorization (RMA) number. When returning to the
manufacturer, the RMA number should be prominently displayed on the outside of the
shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will
be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online at:
Whenever possible, repack the add-on card in the original Supermicro box, using the
original packaging materials. If these are no longer available, be sure to pack the add-on
card in an anti-static bag and inside the box. Make sure that there is enough packaging
material surrounding the add-on card so that it does not become damaged during
shipping.
This warranty only covers normal consumer use and does not cover damages incurred
in shipping or from failure due to the alteration, misuse, abuse or improper maintenance
of products.
During the warranty period, contact your distributor first for any product problems.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contacting SuperMicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
Tel:
Fax:
Email:
+1 (408) 503-8008
[email protected] (General Information)
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
‘s-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
9
Asia-Pacific
Address:
Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3991
Web Site:
Technical Support:
Email:
Tel:
+886-2-8228-1366, ext. 132 or 139
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Guide
Notes
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Safety Guidelines
To avoid personal injury and property damage, carefully follow all the safety steps listed
below when accessing your system or handling the components.
1-1 ESD Safety Guidelines
Electric Static Discharge (ESD) can damage electronic components. To prevent damage
to your system, it is important to handle it very carefully. The following measures are
generally sufficient to protect your equipment from ESD.
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing a component from the antistatic
bag.
•
Handle the add-on card by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the card and peripherals back into their antistatic bags when not in use.
1-2 General Safety Guidelines
•
•
•
Always disconnect power cables before installing or removing any components from
the computer.
Disconnect the power cable before installing or removing any cables from the
system.
Make sure that the add-on card is securely and properly installed on the
motherboard to prevent damage to the system due to power shortage.
1-3 An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest PCB
Revision available at the time of publishing. The card you have received may or may not
look exactly the same as the graphics shown in this manual.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Manual
Notes
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Card Components
2-1 Front Components
Figure 2-1 shows the front components of the AOC-R1UG-IBQ add-on card.
Figure 2-1. AOC-R1UG-IBQ Add-on Card Front Components
4
2
1
3
AOC-R1UG-IBQ
REV: 1.00
DESIGNED IN USA
Table 2-1 lists the add-on card’s front components and their description.
Table 2-1. Front Components
Number Name
Description
1
2
QSFP Connector Port
Port for a single QSFP Connector
Flash ROM Present enable/disable jumper
J1 Jumper
Mellanox ConnectX-2 QDR
chip
3
4
Controller chip for the AOC-R1UG-IBQ add-on card.
This jumper is used for Engineering Debugging only.
J2 Jumper
2-2 Front Connectors, Jumpers and LEDs
This section describes the front connectors, jumpers and LEDs found on the
AOC-R1UG-IBQ add-on card.
QSFP Port
The AOC-R1UG-IBQ card contains a single QSFP port. This port allows the
AOC-R1UG-IBQ add-on card to connect to a QSFP passive copper network cable at
speeds of up to 40 Gbps using four channels. This connector offers four times the
density of traditional SFP ports and support speeds up to 10 Gb/s per channel.
LEDs
The AOC-R1UG-IBQ add-on card contains an LED that is used to display activity as
well as link-up of the port. See Table 2-2 for LED color and blinking definitions.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Manual
Table 2-2. LAN Port LEDs
Definition
LED
Color
Blinking
Yellow
Green
Off
Activity
Port Activity
Logical Link-up
Physical Link-up
No connection
Link-up
J1 Jumper
The J1 jumper is used to tell the Mellanox chip that there is a Flash ROM present in the
system. If the jumper is closed (enabled) it means that no Flash ROM is present, while
open (disabled) means that a Flash ROM is present.
J2 Jumper
The J2 jumper is used for engineer debugging only.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Installation
3-1 Hardware Installation
User the directions below to install the AOC-R1UG-IBQ add-on card into your system.
Before Installation
Before Installation, do the following
1. Power down the system.
2. Remove the power cord from the wall socket.
3. Use industry standard anti-static equipment (i.e. gloves or wrist strap) and/or an
environment that prevents accidental electrostatic discharge.
4. Familiarize yourself with the server, motherboard, and/or chassis documentation.
5. Confirm that your Operating System includes the latest updates and hot-fixes.
Installation
NOTE: This card is designed for the H8DGG-QF serverboard only.
The AOC-R1UG-IBQ add-on card can beinstalled directly into both the SBX connector
and PCI-E 2.0 x8 (in a x16) slot onto the H8DGG-QF serverboard. Position the add-on
card in both the PCI-E slot and over the SBX connector and gently push down on both
sides of the card until it slides into the PCI-E connector and SBX connector together.
Installing the Add-on Card
1. Remove the server cover and, if necessary, set aside any screws for later use.
2. Remove the add-on card slot cover. If the case requires a screw, place the screw
aside for later use.
3. Position the add-on card in both the PCI-E slot and over the SBX connector and
gently push down on both sides of the card until it slides into the PCI-E connector
and SBX connector together.
4. Secure the add-on card to the chassis. If required, use the screw that you previously
removed.
5. Replace the chassis cover.
6. Connect the incoming QSFP cable to the QSFP port provided on the card.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Manual
7. Plug the power cord into the wall socket and power up the system.
3-2 Installing Drivers and Firmware
Use the procedures below to install both drivers and firmware for the AOC-R1UG-IBQ
add-on card for both Linux and Windows.
Linux Drivers
Use the following procedures for installing AOC-R1UG-IBQ add-on card drivers for the
Linux operating system.
Installing InfiniBand Drivers for the Linux Operating System
1. From the CDR-NIC LAN driver CD or FTP site, go to the following directory:
MELLANOX Æ INFINIBAND Æ LINUX.
2. Choose the InfiniBand Linux driver package file.
3. Install the driver by the following commands:
tar xzvf OFED-<ver>.tgz
cd OFED-<ver>
./install.pl
This installs the Linux drivers to your system.
Installing 10G Drivers for the Linux Operating System
1. From the CDR-NIC LAN driver CD or FTP site, go to the following directory:
MELLANOX Æ CONNECTX_EN Æ LINUX.
2. Choose the 10G Linux driver package file.
3. Install the driver by the following commands:
tar xzvf mlnx_en-<ver>.tgz
cd mlnx_en-<ver>
./install.sh
This installs the 10G drivers to your system.
Windows Drivers
Use the following procedures for installing AOC-R1UG-IBQ add-on card drivers for the
Windows operating system.
Installing InfiniBand Drivers for the Windows Operating System
1. From the CDR-NIC LAN driver CD or FTP site, go to the following directory:
MELLANOX Æ INFINIBAND Æ WINDOWS.
2. Choose the desired InfiniBand Windows driver package file.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installation
3. Double-click to run and install the driver package file.
Firmware Update Procedures
Use the following procedures for updating the AOC-R1UG-IBQ add-on card firmware for
both the Linux and Windows operating systems.
Updating Firmware for the Linux Operating System
1. From the CDR-NIC LAN driver CD or FTP site, go to the following directory:
MELLANOX Æ FIRMWARE_TOOL Æ LINUX.
2. Choose the MFT Linux package file and untar the package file.
3. Install the package by the following command:
cd mft-<ver>
./install.sh
4. Install the firmware by the following commands:
mst start
mst status
*note down the pci_cr0 device name*
flint –d <pci_cr0 device name> -i <firmware file name>.bin
b
Upadating Firmware for the Windows Operating System
1. From the CDR-NIC LAN driver CD or FTP site, go to the following directory:
MELLANOX Æ FIRMWARE_TOOL Æ WINDOWS.
2. Choose the desired MFT Windows package file.
3. Double-click to run and install the MFT package file.
4. Open up the DOS Command Prompt and locate the MFT folder.
5. Install the firmware by the following commands:
mst start
mst status
*note down the pci_cr0 device name*
flint –d <pci_cr0 device name> -i <firmware file name>.bin
b
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Manual
Notes
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer
The products sold by Supermicro are not intended for and will not be used in life support
systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to
perform be reasonably expected to result in significant injury or loss of life or
catastrophic property damage. Accordingly, Supermicro disclaims any and all liability,
and should buyer use or sell such products for use in such ultra-hazardous applications,
it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions,
litigation, and proceedings of any kind arising out of or related to such ultra-hazardous
use or sale.
Download from Www.Somanuals.com. All Manuals Search And Download.
AOC-R1UG-IBQ Add-on Card User’s Manual
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
|