SY-7IWB
Motherboard
Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
1
Introduction
Congratulate on your purchase of the SY-7IWB Motherboard. This Quick Start Guide
illustrates the steps for installing and setting up your new Motherboard.
This guide provides all users with the basic steps of Motherboard setting and operation. For
further information, please refer to SY-7IWB Motherboard Uses’ Guide and Technical
Reference online manual enclosed in the CD-ROM package with your Motherboard.
Unpacking
When unpacking the Motherboard, check for the following items:
u
The SY-7IWB
FW82810
AGP/PCI/AMR
Motherboard
u
u
One dual 25-pin parallel
with 25-pin flat cable
and 9-pin serial with 9-
pin flat cable external
connector
u
u
This Quick Start Guide
One dual 6-pin PS/2
mouse connector with
6-pin flat cable and 9-
pin serial connector with
9-pin flat cable
The Installation CD-
ROM
u
SOYO 3-in-1 Bonus
Pack CD-ROM (Norton
AntiVirus, Ghost and
Virtual Drive)
u
u
VGA port flat cable with a
15-pin connector bracket
LINE-IN
MIC
One game port and
Audio connector
bracket with flat cables
u
u
One IDE Device Flat
Cable
LINE-OUT
One Floppy Disk Drive
Flat Cable
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
SY-7IWB Motherboard Layout
JP44
PS/2 Mouse
Connector
WOL
COM 2
KB
Connector
Header
1
3
1
Ac97
Codec
JP1
Winbond
W83627HF
-AW
J10
1
3
1
4
1
1
1
PRT 1
COM 1
ATX Power
CPU FAN
AMR1
4
J11
IR1
1
JP15
1
1
3
AT Power
*
3
1
5
Audiuo Port
PCI Slot #1
1
1
USB1
PCI Slot #2
PCI Slot #3
GAME Port
1
VGA Port
AU8810
Intel
FW82801AB
Intel
FW82810
J6
JP5CMOS Clear
Jumper
+
3 JP2
1
3
Power1
Reset
LED
_
3V
Lithium
Battery
PWRBT
Keylock
+
+
+
Speaker
ACPI
LED
HDD
LED
_
_
JP9
2
2
Intel
FDC
IDE 2
IDE 1
_
82802AB
4MB
1
3
1
1
1
JP10
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Key Features
Ø
Ø
Supports Intel Celeron ™ processors
(300A-500MHz)
Ø
Power failure resume
Ø
Supports onboard hardware monitoring
and includes Hardware Doctor ™ utility
Supports 100 & 66 MHz Front Side Bus
Frequency
Ø
Ø
Ø
Ø
Ø
Ø
Fan speed control
Ø
Ø
Ø
Auto detect CPU bus Frequency (66/100)
Auto-detect CPU voltage
Battery Low voltage Detect
Support 7 sets of voltage monitoring
Supports multiple-boot function
Y2K Compliant
Adjustable CPU Core Voltage (Normal,
5%)
Ø
Ø
Chipset integrated 3D AGP Accelerator
Supports Audio Modem Riser slot (AMR
1.0 compliant) *
Easy CPU settings in BIOS with the
“SOYO COMBO Setup”
Ø
Ø
Ø
Ø
Ø
Ø
3 x 32-bit bus mastering PCI slots
2 x USB ports onboard
1 x IrDA port
Ø
Software Audio AC97 Version 2.1
Compliant
Ø
Ø
PC98, ACPI, Ultra DMA33
Supports Wake-On-LAN (WOL) when
use ATX-Power supply
AT power connector
ATX power connector
Ø
Ø
Supports ACPI Suspend Indicator
Hardware Random Number Generator
(RNG) for enabling enhanced platform
security
Power-on by modem, alarm, PS/2
Keyboard, Mouse and USB Win98
Keyboard
Ø
RTC hardware to handle Y2K Century
Rollover
* If the user wants to use a Modem Riser card (MR) make sure to use aSecondary mode MR, PRIMARY
mode MRs are NOT Supported.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
2
Installation
To avoid damage to your Motherboard, please follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by holding on to an unpainted
portion of the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold the motherboard by the
edges and avoid touching its components.
Check the Motherboard for damage. If any chip appears to be loosened, press
carefully to seat it firmly in its socket.
Follow the directions in this section which is designed to guide you through a quick and
correct method to install your new SY-7IWB Motherboard. For detailed information, please
refer to SY-7IWB Motherboard User's guide and Technical Reference online manual
enclosed in the CD-ROM package with your Motherboard.
Gather and prepare all necessary hardware equipment to complete the installation
successfully:
u
u
u
u
u
u
u
u
u
u
CeleronTM processor with built-in CPU cooling fan (boxed type)
SDRAM module
Computer case and chassis with adequate power supply unit
Monitor
Keyboard
Pointing Device (Mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive …
External Peripherals: Printer, Plotter(optional)
Internal Peripherals: MR and LAN cards (optional)
Note: 1. This Motherboard features one built-in VGA port and three built-in audio-stereo
ports. Therefor you do not need to install neither a VGA card nor a sound card.
2. If you want to use an external speaker connected to "Line-out" port, please make
sure to use an "amplified speaker" that can generate proper output sound volume.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Install the Motherboard
To perform the installation of your new SY-7IWB Motherboard, follow the steps below
Step 1.
CPU Installation
Mark your CPU Frequency: Record the working frequency of your CPU
that should be clearly marked on the CPU cover.
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
466MHz (66 x7..0)
500MHz (66 x7.5)
This Motherboard is designed to support processors with 100MHz FSB. However, Socket
370 processors with 100MHz FSB are not available at present.
CPU Mount Procedure: To mount the Celeron TM processor that you have
purchased separately, follow these instructions.
1
2
3
4
1. Lift the socket handle up to a vertical position.
2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the
socket.
3. Seat the processor in the socket completely and without forcing.
4. Then close the socket handle to secure the CPU in place.
Remember to connect the CPU Cooling Fan to the appropriate power
connector on the Motherboard. The fan is a key component that stabilize the
system. It prevents the equipment from overheating and prolongs the life of
your CPU.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Step 2.
Connections to the Motherboard
This section tells how to connect internal peripherals and the power supply to the
Motherboard.
Internal peripheral is composed of IDE devices (HDD, CD-ROM), Floppy Disk Drive,
Chassis Fan, Front Panel Devices (ACPI LED, Internal Speaker, Reset Button, IDE LED,
and KeyLock Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on connecting internal and external peripherals to your new SY-7IWB
Motherboard, please refer to SY-7IWB Motherboard User's Guide and Technical Reference
online manual on CD-ROM.
Connectors and Plug-ins
Wake-On-LAN Header: JP44
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin1
5VSB
Pin2
Pin3
Pin1
GND
Pin2
12V
Pin3
Pin1
Pin2
12V
Pin3
SENSOR
GND MP-Wakeup
SENSOR GND
IrDA (Infrared Device Header): IR1
Game Port Connector : J5
Connect the game port flat cable from the
game port/ Audio bracket to J5.
Pin1
VCC
Pin2
Pin3
Pin4
Pin5
IRTX
None
IRRX
GND
CD Line-in: J10,J11
Pin1
R
Pin2
G
Pin3
Pin4
G
J10
L
Connect the CD Line-in cord from the CR-ROM
device to the matching connector CDIN
R
G
G
L
J11
Speaker
Key Lock
Power LED
Power LED
Keylock
_
_
1
Pin1
Control Pin
Pin2
GND
Pin1 Pin2 Pin3
NC GND
+
+
5V
Speaker
_
_
1
1
+
+
Pin1
5V
Pin2
NC
Pin3
NC
Pin4
Speaker out
HDD LED
Reset PWRBT
ACPI LED
HDD LED
ACPI LED
PWRBT
RESET
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
LED Anode LED Cathode LED Anode LED Cathode Power On/Off GND Power Good GND
AT Power Cable
ATX Power On/Off: PWRBT
Connect your power switch to this header (momentary switch type).
To turn off the system, press this switch and hold down for longer than
4 seconds.
Connect the AT Power cable
to this connector.
ATX Power Supply: ATX PW
Attach the ATX Power cable to this connector.
When using the Power-On by PS/2 Keyboard function, please make sure the ATX power supply is able to be
loaded at least 720mA on the 5V Standby lead (5VSB) in order to meet the standard ATX specifications.
Note: Use only ONE type of power supply. If an AT power supply is used, do not attach an ATX power
supply.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Step 3. Configure Memory
Your board comes with three DIMM sockets, and provides support up to 512MB main
memory using PC100 DIMM modules from 8MB to 256MB.
Memory Configuration Table
Number of
Memory Modules
DIMM 1
DIMM 2
DIMM 3
Double-sided/
Single-sided
Double-sided/
Single-sided
1
Double-sided/
Single-sided
2
Single-sided
Single-sided²
RAM Type
Memory Module Size (MB)
SDRAM¹
8/16/32/64/256 Mbytes
Note: 1. PC100 Compliant DIMM module is required regardless of 66 or 100
MHz FSB speed.
2. If you want to use DIMM3, DIMM2 must be used as well to let the
system work properly. Just plugging a memory module into DIMM3
with DIMM2 left empty, will make the system not working.
Step 4. Set J6 &JP2 to configure CPU FSB Frequency
If the user wants to use the CPU at its standard FSB (Front Side Bus) Frequency, J6 has to
be closed. This will make sure the system will provide the CPU with the FSB Frequency it
was specified to run at. Make sure that JP2 is open when using this setting.
If the user wants to run the CPU at another (higher) FSB frequency however, J6 has to be
open. In this case use JP2 to set the FSB frequency.
Auto Mode
Description
J6
Short J6
JP2
Run the CPU at its specified FSB frequency.
For 66MHz FSB CPUs 66/75/83 MHz can be
selected in the BIOS.
For 100MHz FSB CPUs 100~133MHz can be
selected in the BIOS.
Must be
open
1 2
3
1 2
Note: Don’t put any jumper on JP2 when J6 is set to short.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Description
Manual Mode
J6
Open J6
J6
JP2
Set power up FSB frequency to 66MHz if the user
wants to run the CPU at a FSB frequency of
66MHz. Only 66~83MHz FSB can be set in the
BIOS.
Short pin
1-2
1 2 3
1 2
JP2
Set Power up FSB frequency to 100MHz if the user
wants to run the CPU at an FSB frequency of
100MHz or higher. This setting will allow the user to
run the CPU at a higher FSB frequency, especially
when the user wants to urn a 66MHz FSB CPU at
100MHz and higher FSB frequencies.
Short pin
2-3
Open J6
1 2
1 2 3
Note: The “Manual” mode setting facilitates FSB over-clocking. Doing so will however force
your CPU to operate out of its specifications, and therefore SOYO can not guarantee the
proper function of your system.
Step 5. Set the CPU Frequency
This Motherboard does not use any jumpers to set the CPU operating frequency; theCPU
settings can be changed through the BIOS [SOYO COMBO SETUP]. Please refer to
Chapter 3 “Quick BIOS Setup” for details on setting the CeleronTM processor frequency.
Step 6. Set for JP9 FWH Boot Block Write-Protect
Setting this jumper to open will prevent the boot block area of the FWH (FirmWare Hub) chip
from being written data into such that it is write-protected from unwanted or abnormal write
activity.
Note: In some rare cases, the boot block area will need to be flashed to complete the BIOS
upgrade procedure. Setting JP9 to open will cause incomplete BIOS update in that case.
The FWH Boot Block
Locked
Unlocked
Write-Protect
JP9 Setting
open JP9
short JP9
1 2
1 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Step 7. Enable/Disable Power-On by Keyboard (JP1)
You may choose to enable the Power-On through Keyboard function by shorting pin 1-2 on
jumper JP1; or short pin 2-3 to disable this function.
Power-On by
Keyboard
Enable
Disable
Short pin 1-2 to
enable the Power-
On by Keyboard
function.
Short pin 2-3 and
the Power-On by
Keyboard function is
disabled.
JP1 Setting
1
2
3
1
2
3
Important: When using the Power-On by Keyboard function, please make sure the
ATX power supply is able to provide at least 720mA on the 5V Standby lead (5VSB)
in order to meet the standard ATX specification.
Step 8. PC speaker redirection (JP10)
Through this jumper the case speaker output can be redirected to the external (amplified)
speakers (if connected) through the on-board Audio-Codec.
PC speaker
redirection
Redirect to external speaker
Use case speaker
JP10 Setting
Short pin 1-2
Short pin 2-3
1
2
3
1
2
3
Step 9. CPU Core Voltage Adjust (JP15)
In case your CPU is running on a frequency higher then it is specified for, increasing its core
voltage can enhance its stability. Over-clocking your CPU does however force your system
to operate outside of its specifications, and therefore SOYO can not guarantee system
stability.
CPU Core Voltage
JP15 Setting
Adjust
Default Vcore
5% higher
short pin 1-2
short pin 2-3
1
2
3
1
2
3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Step 10. CMOS Clear (JP5)
After you have turned off your computer, clear the CMOS memory by momentarily shorting
pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting
in order to recover and retain the default settings.
Jumper JP5 can be easily identified by its white colored cap.
CMOS Clearing
Clear CMOS Data
Retain CMOS Data
Short pin 2-3 for
at least 5 seconds to
clear the CMOS
Short pin 1-2 to
retain new settings
JP5 Setting
1 2 3
1 2 3
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
Note on Over-clocking Capability
The SY-7IWB provides over-clocking capability. Due to the over-clocking setting your system
may fail to boot up or hang during run time. Please perform the following steps to recover
your system from the abnormal situation :
1.Turn off system power (If you use an ATX power supply, and depending on your system,
you may have to press the power button for more than 4 seconds to shut down the
system.)
2.Set the J6 to open and set the JP2 pin 1-2 if you use a FSB 66MHz CPU.
3.Press and hold down the <Insert> key while turning on the system power. Keep holding
down the <Insert> key until you see the message of the CPU type and frequency shown
on the screen.
4.Press the <Del> key during the system diagnostic checks to enter the Award BIOS Setup
program.
5.Select [Soyo Combo Feature] and move the cursor to the [CPU Frequency] field to set the
proper working frequency.
6.Select [Save & Exit SETUP] and press <Enter> to save the new configuration to the
CMOS memory, and continue the boot sequence.
Note: SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
3
Quick BIOS Setup
This Motherboard does not require any hardware jumpers to set the CPU operating
frequency. Instead, CPU settings are software configurable with the BIOS [Soyo Combo
Feature]. The [Soyo Combo Feature] menu combines the main parameters that you need
to configure. They are all in one menu to enable a quick setup in BIOS.
After completion of hardware installation, turn the power switch on, then press the <DEL> key
while the system diagnostic is checking to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then follow these steps to configure the CPU settings.
Step 1. Select [Standard CMOS Features]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 2. Select [Load Optimized Defaults]
Select the “Load Optimized Defaults” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 3. Select [Soyo Combo Feature]
Move the cursor to the [CPU Frequency] field to set the CPU frequency.
The following table shows all available [CPU Frequency] settings on your SY-7IWB
Motherboard . If you set this field to [Manual], then you will be required to fill in the next two
consecutive fields: (1) the CPU Host/PCI Clock, and (2) the CPU Ratio.
CPU Frequency
Select the working frequency of your CeleronTM
processor among these preset values.
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
466MHz (66 x 7.0)
500MHz (66 x 7.5)
Note:
Mark the checkbox that corresponds to
the working frequency of your CeleronTM processor
if the CMOS configuration is lost.
Note: if you use Bus Frequencies of 75 MHz, make sure that your PCI cards are compatible
with the higher PCI clock.
Step 4. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue with the
boot sequence.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
4
The SOYO CD
The SOYO-CD will NOT autorun if you use it on an Operating System other
than Windows 9x or NT.
Your SY-7IWB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains (1) the user's manual file for your new Motherboard, (2) the drivers software
available for installation, and (3) a database in HTML format with information on SOYO
Motherboards and other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be shown as below.
(SOYO CD Start Up Program Menu)
If you use Windows 95/98, the SOYO CD Start Up Program automatically detects which
SOYO Motherboard you own and displays the corresponding model name.
Step 2. Read SOYO [7IWB] Manual
Click the Read Manual button to open the user's manual file of your Motherboard.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Please note that if the Start Up program was unable to determine which SOYO
Motherboard you own, the manual selection menu will pop up, as shown below. Then
select the user's manual file that corresponds to your Motherboard model name and click
OK.
SOYO CD Manuals
Please select your manual in the box below
and click OK.
686 boards:
7IWB
586 boards:
OK
Back
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the Install Drivers button to display the list of drivers software that can be installed
with your Motherboard. The Start Up program displays the drivers available for the
particular model of Motherboard you own. We recommend that you only install those
drivers. If you use Windows NT, only select the drivers listed here.
However, to display the list of all drivers software available with SOYO Motherboards, click
the Display all drivers on the SOYO CD button. Please make sure to install only the
drivers adapted to your system, or otherwise this may cause system malfunctions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel Whitney VGA Drivers for Win 9x
Intel .inf utility for Win 9x
Intel Whitney security utility for Win 9x/NT
7IWB Winbond hardware Doctor for Win 95/98
Display all drivers
on the SOYO CD
Cancel
OK
(Driver Installation Menu)
A short description of all available drivers follows:
Ø
INTEL Whitney VGA Drivers for Win 9x
In order to be able to make use of the integrated VGA function in your Whitney
chipset, you will need to install this driver first. For Windows 95/98 only.
Ø
INTEL Whitney .inf utility for Win 9x
Windows 95 and 98 will not recognize the new INTEL Whitney chipset properly. To
update the necessary .inf files that will help Windows recognize the Whitney chipset,
please run this utility.
Ø
INTEL Whitney security utility for Win 9x/NT
This utility makes use of the random number generator in the FWH of your 810/820
chipset. for Win 95/98/NT.
Ø
7IWB Winbond hardware Doctor for Win 95/98
Your motherboard comes with a hardware monitoring IC. By installing this utility
Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms
when current system values exceed or fall below pre-set values.
Select which driver you want to install and click OK, or click Cancel to abort the driver
installation and return to the main menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers
require to restart your system before they can become active.
Step 4. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to automatically find
the latest BIOS, manual and driver releases for your motherboard. This button will only
work if your computer is connected to the internet through a network or modem
connection. Make sure to get your modem connection up before clicking this button.
Step 5. Enter the SOYO CD
Click the Enter SOYO CD button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to display the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available. For your convenience, this information is available in HTML format,
similar to the format widely used on the Internet.
Note: If no HTML browser is installed on your system, the Start Up program will prompt
you on whether or not you would like to install the Internet Explorer* browser. Click YES to
install the HTML browser. After the installation is complete, please restart your system.
Then re-run the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
5
Crystal Audio Driver Installation
Installing Crystal Audio Drivers under windows 9x
1. Open Device Manager.
2. PCI Multimedia Device will have a yellow marker the first time the operating system is installed.
3. Select "Properties" on the yellow marker.
4. Select the "Driver" tab.
5. Click on "Update Driver"
6. Select the following directory:
D:\driv-all\crystal\window9x\image
and click OK. You will need the Windows Second Edition to complete the WDM installation.
7. The entry that will show up in the Sound, Video, and Game Controllers is: Crystal WDM Audio
Codec.
8. A little Sound Icon appears on the Task Bar upon completing the driver installation.
Uninstalling/Re-Installing Crystal Audio Drivers
1. Open Device Manager.
2. Remove Crystal WDM Audio Codec entry in the Sound, Video, and GameControllers section.
Crystal is not the owner of the game controller on this audio solution.
3. Delete Crystal INF in c:\windows\inf\other
4. Restart your PC for Plug and Play to reinitialize your system.
Known Limitations
1. Clicking the Stop button causes loud pops while playing Midi through Media Player, when
Headphone control is used.
2. Playing any wave using the Dsound application causes a loud pop when the Play button is clicked.
3. After Remove/Refresh, no software wavetable audio is available after a reboot.
4. The Play and Stop button cause loud pops while playing wave through the Media player.
5. There may be some feed back noise when Microphone boost is enabled.
6. A reboot may be required to play MIDI audio after the initial installation of the driver.
7. Panning Headphone and Wave balance in the Output mixer while playing a aWave/CD/Line-in
signal causes a pop.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
Special Design Considerations
1. The Headphone does not mute the audio when the headphone slider is adjusted to the minimum
value.
2. SW Synth slider jumps to max value, when Synth state is switched from Stop to Play or viceversa.
3. Master Volume levels are quite low when compared to Headphone volume levels.
4. Fastforward and Rewind Controls in the Media Player can not enabled.
5. When resuming from sw wavetable playback, midi is paused.
6. Digital CD Audio is recorded by loopback mux selection.
7. Mono Mix volume is low.
8. Some Dos games do not run in a Dos Box. This support is provided by the Microsoft legacy Audio
emulator.
Note: The above limitations list is as provided by the codec manufacturer, SOYO will provide customers
with new driver releases through the SOYO website as soon as they are released by the manufacturer.
Installing Crystal Audio Drivers for Windows NT
1. Double click the MULTIMEDIA icon in the control panel. The Multimedia Properties windows will
appear. Click on the Devices tab and press the Add button.
2. Select "Unlisted or Updated Drivers" from the list of drivers in the Add window by placing the mouse
pointer over it and clicking the left mouse button. Press the OK button.
3. The Install Driver dialog box will appear and request the path of the location of the drivers to be
installed. Enter D:\driv-all\crystal\NT (where D: is your CDROM drive) If the installation fails, first copy
all the files in the above directory to your harddisk and give that directory to NT.
4. The label "SoundFusion(tm)" is displayed on the dialog box. Press OK to continue with the
installation.
5. Windows NT will display a dialog box asking you to restart your system.
Press the Restart Now button to complete the installation.
Uninstalling or Updating Crystal Audio Drivers
1. Double click on the MULTIMEDIA icon in the control panel. Select the Devices tab from the
Multimedia properties window.
2. Double click on the Audio Devices entry from the Multimedia devices list. Select the driver by placing
the mouse pointer over the label "Audio for SoundFusion(tm)" and clicking the left mouse button.
3. Press the REMOVE button.
4. A question box will appear to verify your decision. Press the YES button.
5. WindowsNT will dislplay a dialog box asking you to restart your system. Press the Restart Now
button to complete the Un-installation.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
How to contact us:
n
If you are interested in our products, please contact the SOYO sales
department in the region you live.
n
If you require Technical Assistance, please contact our Technical Support in
the region you live.
SOYO prefers Email as communication medium, remember to always add to the
email the country that you live in.
SOYO Taiwan
SOYO USA
41484 Christy Street, Fremont, CA
94538
No. 21 Wu-Kung 5 Rd., Hsin Chuang
City, Taipei Hsien, Taiwan
Region Covered: US and Canada
Region Covered: Taiwan and Asia-
Pacific. (Including Australia).
Web Site: www.soyo.com.tw
Sales:
Sales:
Tel: 510-226-7696
Fax: 510-226-9218
Email : [email protected]
Tel: 886-2-22903300-318
Fax: 886-2-22983322
E-mail: [email protected]
Technical Support:
Tel: 510-226-7696
Fax: 510-226-9218
Email : [email protected]
Technical Support:
Fax: 886-2-22983322
E-mail: [email protected]
SOYO Europe BV
SOYO (U.K.) LTD.
Signaalrood 19, 2718 SH Zoetermeer
The Netherlands
Unit 7, Alice Way, Hounslow Business
Park,
Hanworth Road, Hounslow, TW3 3UD
Region Covered: Europe except
Germany, Austria and Switserland
Region Covered: United Kingdom and
Republic of Ireland
europe.com
Web Site: www.soyo.co.uk
Sales:
Tel : +44 (0)181 569 4111
Fax: +44 (0)181 569 4134
E-mail: [email protected]
Sales:
Tel: +31-69-3637500
Fax: +31-79-3637575
Email: [email protected]
Technical Support:
Technical Support:
Tel : +44 (0)181 569 4111
Fax: +44 (0)181 569 4134
Tel : +31-79-3637500
Fax: +31-79-3637575
Email: [email protected]
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-7IWB Quick Start Guide
E-Mail: [email protected]
Sales:
tel: 852-27109810
SOYO Deutschland GmbH
fax: 852-27109078
E-mail: [email protected]
August-Wilhelm-Kuhnholz-Str. 15
D-26135 Oldenburg
Technical Support:
tel: 852-27109810
fax: 852-27109078
E-mail: [email protected]
Region Covered: Germany, Austria
and Switzerland. (Zustandig fur
Deutschland, Osterreich, Schweiz)
SOYO China (Gin Mei Jei)
Vertrieb Mainboards, Notebooks und
SoyoCom Produkte:
E-Mail: [email protected]
Region Covered: All of China
Sales:
Tel: 86-10-62510089
fax: 86-10-62510388
E-mail: [email protected]
Fon: +49-(0)441/20910-31/33
Fax: +49-(0)441/203422
Technischer Support:
Technical Support:
E-Mail: [email protected]
Fon: +49-(0)441/20910-40
Fax: +49-(0)441/203422
Tel: 86-10-62510089
fax: 86-10-62510388
E-mail: [email protected]
SOYO KOREA
SOYO Japan
Region Covered: Korea
Region Covered: Japan
Web site: www.soyo.co.jp
Sales:
Tel : 82-2-716-2850
Fax : 82-2-704-2619
E-mail : [email protected]
Sales:
Tel: 81-3-33682188
Fax: 81-3-33682199
E-mail: [email protected]
Technical Support:
tel : 82-2-717-4392
Technical Support:
Tel: 81-3-33682188
fax : 82-2-712-5853
e-mail : [email protected]
Fax: 81-3-33682199
E-mail: [email protected]
SOYO Hong Kong
Region Covered: Hong Kong
Web Site: www.soyo.com.hk
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: July 1999
Version 1.0
SY-7IWB
SERIAL
Download from Www.Somanuals.com. All Manuals Search And Download.
|