FireWire800+Hi-Speed
USB Combo
Quick Installation Guide
Introducing the FireWire 800 + Hi-Speed
USB Combo
The FireWire 800+Hi-Speed USB Combo features the latest
technology in FireWire 800 and USB 2.0.
FeaturesandBenefits
•
•
•
Combo card design adds five USB 2.0 (480 Mbps),
one 1394a (400Mbps) and two 1394b (800 Mbps)
ports into your system.
Built-in4-pinpowerconnectorprovidesextrapower
when connected to the system's power supply
(Recommended)
Supportshot-swappingandPlug-n-Playconnection
of peripheral devices
FireWire 800 (1394b) interface
•
•
•
•
Provides 3 FireWire ports for multiple 1394b and
1394a device connections
Adds two FireWire 800 (1394b) ports (1 int. + 1 ext.)
and one external 1394a (400Mbps) port
Supports IEEE 1394b and backwards compatible
with 1394a-2000 and 1394-1995 standards
Supports data transfer rates of 100, 200, 400, and
800Mbps
04-0447B
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PackageContents
•
•
•
•
FireWire 800+Hi-Speed USB Combo adapter
"Y" split power cable
Driver CD
Quick Installation Guide
BoardLayout
1394b (9-pin)
1394a (6-pin)
1394b (9-pin)
USB Pin-out
Header
USB 2.0
Power Connector
(recommended)
USB 2.0
Figure 1. Board Layout
Note: The Power Connector (same as the one used
with your floppy disk drive) is designed to provide
additional power to the board when needed.
Connectthispowerconnector(recommended)when
one of the following conditions occur:
- Device(s) not being detected.
- All ports are used.
Power off your system first before making this
connection.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USBPin-outHeader
The internal USB Pin-out Header consists of 9 pins
arranged in 2 rows; the header provides 2 USB ports.
Match up +5VDC (Pin 1) on the 4-Pin USB Connector to
Pin 1 on the pin-out header. Connecting the USB cable
improperly may damage the system. Please refer to your
system's manual for proper connection.
Pin
1
Assignment
+5VDC
Pin
2
Assignment
+5VDC
3
USB- (Data-)
USB+ (Data+)
Ground (GND)
None
4
USB- (Data-)
USB+ (Data+)
Ground (GND)
Ground (GND)
5
6
7
8
9
10
Figure 2. USB Pin-out Header
Note: The diagram and table shows labeling for a
typical motherboard 9-pin pin-out header. Please
notethatthe1stpinonthe5-pinrowoftheFireWire
800+Hi-Speed Combo is labeled pin1 but
corresponds to pin 2 on the diagram, nevertheless ,
the assignment for each pin are identical to the
table. The pin-out header is designed to connect to
front mounted USB ports, flash memory card
readers, or any USB devices that require pin-out
header connection. Reference the image above and
review your computer's manual for proper
connection.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices. Unplug the
computer's power cord.
2. Remove your computer’s cover and install the card
in an available PCI slot.
3. Push the board down firmly, but gently, until it is
well seated.
4. Connect internal connections where needed. See
Board Layout on page 3 for more details.
5. Secure the card and replace the cover.
Figure 3. Inserting the PCI Board
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Driver Installation
The instructions below are divided into two sections,
USB 2.0 and FireWire 800. To ensure proper installation
of this board, please follow the instructions step-by-step.
USB 2.0 Driver Installation
For Windows 2000 (with SP4 or later)/XP (with SP1 or
later)/2003/Vista
Windows will automatically detect and install it's
built-in USB 2.0 driver. No additional driver installation
is needed. The board will operate at USB 2.0 speed.
For Window 2000 (with SP3 or earlier)
Windows will automatically detect and install it's
built- in USB 1.1 driver. The board will operate at USB 1.1
speed.
1. At the Found New Hardware Wizard, click Next.
2.
Select Search for the best driver..., click Next.
3. Uncheck all boxes, then click Next.
4. Select Disable the Device..., then click Finish.
XP (without SP1)
Windows will automatically detect and install it's
built- in USB 1.1 driver. The board will operate at USB 1.1
speed.
1. At the Found New Hardware Wizard select Install
the software automatically, then click Next.
2. Select No, do not connect to the internet now, then
click Next.
3.
Check Don't prompt me again to install this
software, then click Finish.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FireWire 800 Driver Installation
Windows will automatically install it's built-in FireWire
400 driver for the FireWire 800 + Hi-Speed USB Combo. To
get the full speed from the controller, install the FireWire
800 driver using the directions below.
Windows2000
Windows2000automaticallyinstallsit's built-inFireWire
400 driver for the FireWire 800 + Hi-Speed USB Combo. To
getthefullspeedoutofthiscontroller,installtheFirewire
800 driver using the directions below.
1. Insert the driver CD. Click Start, Run. Type
D:\setup32.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Program Folder screen, click Next.
7. At the Digital Signature screen, click Yes, then click
Finish.
8. Selecttherestartcomputeroption, thenclickFinish.
32-bitWindowsXP
Windows XP automatically installs it's built-in 1394a
driver for the FireWire 800 + Hi-Speed USB Combo. To get
the full speed out of this controller, install the FireWire
800 driver using the directions below.
1. Insert the driver CD. Click Start, Run. Type
D:\setup32.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Program Folder screen, click Next.
7. At the Software Installation screen, click Continue
Anyway, then click Finish.
8. Selecttherestartcomputeroption, thenclickFinish.
64-bitWindowsXP
Windows XP automatically installs it's built-in 1394a
driver for the FireWire 800 + Hi-Speed USB Combo. To get
the full speed out of this controller, install the FireWire
800 driver using the directions below.
1. Insert the driver CD. Click Start, Run. Type
D:\setup64.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Program Folder screen, click Next.
7. At the Security Alert box, click Yes two times.
8. At the Software Installation screen, click Continue
Anyway, then click Finish.
9. Selecttherestartcomputeroption, thenclickFinish.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
32-bitWindowsServer2003
Windows Server 2003 automatically installs it's
built-inFireWire400driverfortheFireWire800+Hi-Speed
USB Combo. To get the full speed out of this controller,
installtheFireWire800driverusingthedirectionsbelow.
1. Insert the driver CD. Click Start, Run. Type
D:\setup32.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Program Folder screen, click Next.
7. At the Security Alert box, click Yes two times.
8. At the Software Installation screen, click Continue
Anyway, then click Finish.
9. Selecttherestartcomputeroption, thenclickFinish.
64-bitWindowsServer2003
Windows Server 2003 automatically installs it's
built-inFireWire400driverfortheFireWire800+Hi-Speed
USB Combo. To get the full speed out of this controller,
installtheFireWire800driverusingthedirectionsbelow.
1. Insert the driver CD. Click Start, Run. Type
D:\setup64.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. At the Program Folder screen, click Next.
7. At the Security Alert box, click Yes two times.
8. At the Software Installation screen, click Continue
Anyway, then click Finish.
9. Selecttherestartcomputeroption, thenclickFinish.
WindowsVista™
Windows Vista operating system automatically installs
it's built-in FireWire 400 driver for the FireWire 800 + Hi-
Speed USB Combo. To get the full speed out of this
controller, install the FireWire 800 driver using the
directions below.
1. Insert the driver CD. Click Start.
For32-bitWindowsVista:IntheStartSearchbox,type
D:\setup32.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
For64-bitWindowsVista:IntheStartSearchbox,type
D:\setup64.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
2. Click Allow.
3. At the Welcome screen, click Next.
4. At the License Agreement screen, click Yes.
5. At the Destination Location screen, click Next.
6.
Select Complete, then click Next.
7. At the Program Folder screen, click Next.
8. At the Windows Security box, click Install three
times, then click Finish.
9. Selecttherestartcomputeroption, thenclickFinish.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ToVerifyWindowsInstallation
1. Check Device Manger to verify installation:
For 2000/XP/Server 2003: Right click My Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer, click
Manage, click Continue, click Device Manager.
2. The drivers for this controller show up differently
under different versions of Windows. Please refer
to the correct Windows version to verify:
Windows 2000 (with SP4 or later):
a) Under Universal Serial Bus Controllers:
- NEC... Open Host Controller
- NEC... Open Host Controller
- Standard Enhanced PCI to USB Host Controller
- USB 2.0 Root Hub
- USB Root Hub
- USB Root Hub
b) Under 1394 Bus host controllers:
- Unibrain driver/OHCI Compatible Board or
IEEE 1394b (FireWire 800) adapter
Windows2000(withSP3orearlier)andXP(without
SP1):
a) Under Universal Serial Bus Controllers:
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- USB Root Hub
- USB Root Hub
11
Download from Www.Somanuals.com. All Manuals Search And Download.
b) Under 1394 Bus host controllers:
- Unibrain driver/OHCI Compatible Board or
IEEE 1394b (FireWire 800) adapter
c) Under Other Devices:
- UniversalSerialBus(USB)Controllerwilldisplay
with a yellow exclamation mark.
Windows XP (with SP1 or later)/Server 2003/Vista:
a) Under Universal Serial Bus Controllers:
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- Standard Enhanced... USB Host Controller
- USB Root Hub
- USB Root Hub
- USB Root Hub
b) Under 1394 Bus host controllers:
- Unibrain driver/OHCI Compatible Board or
IEEE 1394b (FireWire 800) adapter
Mac OS Driver Installation
The instructions below are divided into two sections,
USB 2.0 and FireWire 800. To ensure proper installation
of this board, please follow the instructions step-by-step
in both sections.
USBDriverInstallation
Mac OS 8.6-9.x, OS X (version 10.2.7 and earlier)
This board will only work at USB 1.1 speed in these OSes.
Just install the board and Mac OS will automatically
detect and install the correct USB 1.1 driver for it. No
additional driver is necessary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Mac OS X (version 10.2.8 ) or later
Mac OS X (version 10.2.8) or later have built-in USB 2.0
driver support for this controller. Just install the board
and Mac OS will automatically detect and install the
correct drivers for it. No additional driver is necessary.
FireWireDriverInstallation
To ensure proper operation of the FireWire 800+Hi-Speed
USB Combo in your Mac, some Mac OS requires the most
current Firewire software from Apple. Apple's website
contains all the information needed to download and
installFirewiresoftwareupdate. Macsoftwaredownload
When you are at the download page, in the Search box,
check Restrict to downloads, type in 1394, then click the
search button. The information below will help you
decide whether or not to download and install the latest
Firewire driver update.
1.
Mac OS 10.2.4 or later has built-in Firewire 800
(1394b) driver support with the operating system.
No driver installation is needed. The firewire 800
ports will work up to 800 Mbps.
2.
Mac OS 9.1, 9.2.x, and Mac OS 10.1.x-10.2.3 have
built-inFirewire400(1394a)driversupportwiththe
operating system. No driver installation isneeded.
The Firewire 800 ports will work up to 400 Mbps.
3.
4.
Mac OS 9.0.x users should download the Firewire
software version 2.5 or later. The Firewire 800 ports
will work up to 400 Mbps.
Mac OS 8.6 users should download the Firewire
software version 2.3.3. The Firewire 800 ports will
work up to 400 Mbps.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To Verify Mac OS Installation
Since we didn't load any additional driver under these
Mac OSes, plug in a USB device to verify installation.
Connecting Devices
General driver installation steps are provided below.
Pleasereviewyourdevice'susermanualformoredetails.
USBDevices
Windows and Mac OS will automatically detect and
install most USB devices when connected. For devices
that do not install automatically, additional drivers may
be required. Refer to the device's users manual for more
information.
FireWireDevices
For Windows 2000
1. At the Found New Hardware Wizard, click Next.
2. SelectSearchforasuitabledriver...,thenclickNext.
3. Uncheck all check boxes, then click Next.
4. Click Next, then click Finish.
For Windows XP
1. At the Found New Hardware Wizard,
For XP w/SP2 or later
Select No, not this time, then click Next.
For XP w/SP1 or earlier
Go directly to step #2.
2. SelectInstalltheSoftwareAutomatically,thenclick
Next.
3. Click Continue Anyway. (Skip if not prompted)
4. Click Finish to complete the installation.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
For Server 2003
1. At the Found New Hardware Wizard,
For 2003 w/SP1 or later
Select No, not this time, then click Next.
For 2003 no service pack installed
Go directly to step #2.
2. SelectInstalltheSoftwareAutomatically,then click
Next.
3. At the Security Alert box click Yes, or the Hardware
Installation box click Continue Anyway, then click
Finish to complete the installation.
For Windows Vista
Windows Vista will automatically detect and install the
drivers for most FireWire devices when connected.
However, for devices that do not install automatically,
follow the steps below to complete the installation.
1. Click Locate and install driver software.
2. Click Continue to complete the installation.
For Mac OS
MacOSwillautomaticallydetectandinstallmostFireWire
devices when connected. For devices that do not install
automatically, additional drivers may be required. Refer
to the device's users manual for more information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ubSwitch Utility (for Windows only)
In order to use a DV camcorder with this controller,
Microsoft's FireWire 400 driver must be installed in the
system. We have supplied an easy to use utility that
allows switching between Microsoft's driver and the
FireWire 800 driver. Before using this utility, unplug all
devices from the FireWire 800 card.
1. Click Start, Programs, Unibrain ubcore, Tools then
ubSwitch.
2. Right click the ubSwitch icon located in the system
tray by the clock.
3. Clickthe1394Adapterthatyouwanttoswitch,then
click on Microsoft 1394 Drivers.
Note: If your system has multiple 1394 adapters
installed, make sure that you click on the 1394
adapter that the camcorder will be plugged into.
4. Windows will display an information box when the
driver is ready for use. It may take a few seconds for
this box to appear.
Note: To switch back to the FireWire 800 driver,
follow the same procedures, but in step 3 instead of
clickingonMicrosoft1394Drivers,clickonUnibrain
1394 Drivers.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’sOnlineSupporthasanswers! Simplyvisitour
database is updated daily with new drivers and solutions. Answers
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
request to SIIG RMA. If the product is determined to be
defective,anRMAnumberwillbeissued. SIIGRMAdepartment
can also be reached at (510) 413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA#:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,andthroughe-commercesites.
PRODUCT NAME
FireWire 800 + Hi-Speed USB Combo
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
FireWire800+Hi-SpeedUSBComboisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregistered
trademarksofSIIG,Inc. Microsoft,WindowsandWindowsVistaareeitherregisteredtrademarksor
trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a
registered trademark of Intel Corporation. Mac and Mac OS are registered trademarks of Apple
Computer,Inc. Othernamesusedinthispublicationareforidentificationonlyandmaybetrademarks
oftheirrespectivecompanies.
March, 2008
Copyright © 2008 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|