BUSINESS PRINTER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S MANUAL
24-pin wide-carriage
dot matrix printer
As an ENERGY STAR Partner, SEIKO Precision Inc. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
- Outline of the International ENERGY STAR Office Equipment Program -
The International ENERGY STAR Office Equipment Program is an international program
that promotes energy saving through the use of computers and other office equipment. The
program backs the development and dissemination of products with functions that effectively
reduce energy consumption. It is an open system in which business proprietors can participate
voluntarily. The targeted products are office equipment such as computers, displays, printers, facsimiles,
and copiers. Their standards and logos uniform among participating nations.
C
2000 SEIKO Precision Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
This manual is for the following two models of the printer.
Although these two models, model A and model B, look different,
the difference is only the appearance of the casing areas at the front. The
functions of these models are very much the same.
Refer to the manual of the model A, for the manual of the model B.
Model A
Model B
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Caution for use
Unpacking the printer..............
Quick startup..............................
19 Line feed spacing.......................... 40
20 Slashed zero................................ 40
21 Set default tab stops...................... 40
22 Lock-in the page length................. 40
23 Print quality ............................... 41
24 Lock-in the font........................... 41
25 Lock-in the character
1
2
1. Introduction
Features......................................
Options and expendables........... ......
Power code ........................... ......
Printer description..................... . .. .
Precaution for extra-thick
3
4
5
6
spacing .................................... 41
26 Lock-in the print quality................. 41
Barcode print enhancement
27 Enable barcode print
paper usage ...................... ......
Physical dimension(Model A)......... ..
Physical dimension(Model B)......... ..
7
8
9
and Enlarged character ................ 42
28 Barcode type............................... 42
29 Bar code size................................ 44
30 Enlarged character size................... 44
31 Graphic Print Speed...................... 45
32 Accent character........................... 45
33 Setting of the FF code at TOF ......... 45
2. Setting up
Installing the paper rack ................ 10
Installing the sound seal cover ........ 10
Installing the ribbon cassette . . . . . . . . 11
Connecting the computer ........... . . . . 12
Connecting the power cord ............. 12
Loading the paper.......................... 13
Adjusting the print head position..... . . 15
HP mode enhancement
38 PCL mode .................................. 46
39 Secondary character table ............ 46
Paper handling enhancement
40 Set the top margin........................ 47
41 Set the bottom margin .................. 47
42 Set the left margin........................ 47
43 Set the right margin ..................... 48
44 Fanfold paper width ..................... 48
45 Autoscroll delay........................... 48
46 Override bottom margin ............... 49
47 Label mode................................. 50
48 Setting of "Paper out" detection....... 50
49 Cut sheet feeder type..................... 50
50 Setting of the auto-scrolling
3. Control panel and operations
Control panel and indicators ......... 16
Control Levers .......................... 19
Paper parking ......................... . . . . . 20
Printing test pattern ...................... 21
Demonstration print-out ................ 22
Tearing off a form.......................... 22
Power-on operation summary ......... 23
4. Basic setup options
About basic setup options ............. 24
Printing multipart paper ................ 26
Selecting page length
position ............................ 50
51 Line Feed Speed............................ 51
for fanfold paper...................... 26
Selecting single sheet
paper size .............................. 27
Selecting font style ...................... 28
Selecting character spacing ........... 29
Enlarging/compressing print ......... 30
Setting top of form position ........... 31
Loading user & factory
C o m m u n i c a t i o n e n h a n c e m e n t
60 Interface type............................... 51
6 1 SELECT IN signal......................... 51
62 Parity bit ................................... 51
63 Data length................................. 52
64 Stop bit..................................... 52
65 Communication protocol ............. 52
66 Communication speed .................. 52
67 Serial error check ........................ 53
68 CTS signal................................. 53
69 CD signal .................................. 53
70 DSR signal................................. 53
setup options ............ 31
5. Extended setup options
About extended setup options . . . ... . . 33
Extended setup options summary. . . ... . . 34
Print enhancement
71 Communication buffer size
........ 54
10 Emulation................................... 36
11 Character table (HP mode)............... 36
12 Character table (Epson mode)........... 37
13 Character table (IBM mode)............. 37
14 National font style........................ 38
15 Code page................................... 38
16 IBM Alternate graphic mode............ 39
17 Carriage return (CR)....................... 39
18 Line feed (LF)............................... 39
72 Busy/ACK timing......................... 54
73 Data latch timing.......................... 54
74 Setting of whether ERROR/PE
signals are output or not ...... 54
M i s c e l l a n e o u s
80 Print direction............................. 55
81 LCD display language.................... 55
82 Invert LCD display ...................... 55
Download from Www.Somanuals.com. All Manuals Search And Download.
82 Invert LCD display ...................... 55
83 Software controlled setup ............. 56
84 Lock the RESET key...................... 56
85 Setting ENERGY STAR .... ............. 56
86 Saving user setup options ............. 56
87 Printing list of setup options .... ..... 56
HRI...................................... 76
Error processing...................... 77
Code 128 subset transition rule...... 77
UPC-E conversion rule.............. 78
Calculating the check character...... 78
Other.................................... 80
Element printing..................... 80
Element printing example ......... 81
6. Setting the application software
About printer driver ...................... 57
Printer driver selection .................. 57
Connecting the BX-900 printer
Enlarged
character function
Outline of enlarged
in the HP environment ............. 58
Saving Your Setup ......................... 59
characterfunction............ 82
Enlarged character
7. Troubleshooting
command list................. 82
(1) Executing backspacing............ 83
(2) Executing line feeding............. 83
(3) Executing form feeding............ 84
(4) Executing carriage return.......... 84
(5) Initializing the enlarged
character mode............... 84
(6) Arrangement of enlarged
characters..................... 85
(7) Cell expansion for
Error messages ............................ 60
Troubleshooting guide .................. 61
Input hexadecimal dump mode
.. . .. 62
8. Maintenance
Cleaning...................................... 63
Lubrication.................................. 64
Printer cover removal ................... 64
Vertical alignment mode ............... 66
enlarged characters.................. 85
(8) All-character set for
enlarged characters................... 86
(9) Selecting an enlarged
character font......................... 86
(10) Height expansion for
9. Bar code and enlarged character
Bar code function
Outline of bar code function................. 69
Bar code command list........................ 70
(1) Bar code type........................ 70
(2) Element width....................... 71
(3) Bar code height..................... 71
(4) Setting HRI on and off............. 71
(5) HRI font.............................. 72
(6) Check character..................... 72
(7) Starting the bar code data sequence... 72
(8) Ending the bar code data sequence.... 73
(9) Bar code data sequence............. 73
(10) Printing density................... 73
(11) Guard bar expansion.............. 73
(12) Start and stop characters......... 74
(13) Bar code rotational angle........ 74
(14) Disabling HRI of the start
enlarged characters.................. 87
(11) HMI for enlarged characters.......... 87
(12) VMI for enlarged characters........... 88
(13) Setting and canceling the
enlarged character mode...... 88
(14) Enlarged character cell offset..... 89
(15) Enlarged character pitch......... 89
(16) Enlarged character quality....... 90
(17) Enlarged character rotational angle
.
.
90
(18) Setting and canceling enlarged
character smoothing. . 91
(19) Enlarged character top offset...... 91
(20) Setting and canceling underline
for enlarged characters... 92
and stop characters.......... 74
(15) Value input mode.................. 74
(16) Initializing the bar code mode.... 75
(21) Enlarged character
width expansition ........... 92
(22) Horizontal printing position
for enlarged characters... 92
(23) Vertical printing position for
enlarged characters. . 93
Data processing in the bar
code data sequence........... 75
Printing bar codes.................... 76
Enlarged character print samples..... 94
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
A. Specifications
Printing specifications ............. 95
Parallel interface
specifications ............... . 100
Serial interface
specifications ............... . 101
Other specifications ................ 102
B. Control code summary
IBM mode ............................. . 103
EPSON mode ......................... . . 109
PCL mode ........................... . . . 115
Setup options control codes ........ 122
C. Character sets........... ............... 127
D. Reverse control panel sheet ....... 136
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution for use
❏ Power sourc e
• Be sure to insert the power plug only in a
wall unit of the voltage designated in the
voltage selector and on the rating plate on
the back of the unit.
• Do not place the power cord near heat
sources or place heavy objects on it. Do not
bend or twist the power cord.
❏ Foreign matter and water
• Keep your hands and personal items, such as
scarfs and ties, away from the carriage
mechanism while the printer is operating.
The carriage moves with considerable force.
• Keep the printer dry. If you accidentally
spill water on the machine, turn the power
off immediately and wipe it dry. Do not turn
the power on until the machine is
completely dry.
❏ Installation environment
• The printer should be used where humidity is
low, where there is little dust, and where the
printer is not in direct sunlight.
• Avoid placing or leaning anything on top of
the printer. If you accidentally drop any
object into the machine, turn the power off
immediately, and disconnect the power code
from the wall outlet, then carefully remove
the object.
• Do not twist the ribbon while installing it.
❏ Operating condition
• Wait at least two seconds after turning power
off before turning it back again. The
initialization process may not be performed
correctly if this is not done.
• Do not touch the print head immediately
after printing because it is too hot.
• Never operate the printer without paper nor ribbon properly installed.
If you use paper that is not as wide as the platen, be sure that printing does not exceed paper width.
• Never insert or pull out the interface cable while the power to the printer and computer is on.
• Be sure to turn off the printer before turning off a connected host computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking the printer
Unpacking the printer
Check the cartons for the following items:
BUSINESS PRINTER
CD-ROM
(Driver-CD with Owner’s
NERS MAUAL
Handbook
Manual, printer driver software)
T O F S E T
M . L F
L F
F F
P O W E R
L I N O E N
R E S E T
P . O U T
O F F T E A R L I N O E N
P A R K
B I N
Q U A L I T Y
E N T E R
L
C
D
R L F
M . R L F
E X I T
S E T U P
A L T
Reverse Control Panel
Handbook
(See page 55, 136)
Paper Rack
(See page 10)
Sound Seal Cover
Ribbon Cassette
(See page 10)
(#SBP-3051)
(See page 11)
Power Cord
Printer
(See page 12)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick startup
Quick startup
To make your first print, follow the procedure below . For more detailed instructions on setting your
printer, please refer to the page indicated.
❏ To set up the printer
1. Install the paper rack, the sound seal cover,
and the ribbon cassette — Pages 10 and 11.
2. Load the single cut sheet paper or fanfold
paper. Press the FF key to load the paper —
Pages 13 and 14.
❏ To make a test print
1. Set the paper size of the printer in the setup
options — Pages 26 and 27.
2. Press the LF key and hold while initializing
the printer by the RESET key. Hold the LF
key until the self test starts — Page 21.
❏ To connect your computer
1. With all equipment turned off, connect the
printer to your computer. Interface cable is
purchased separately — Page 12.
2. Use the extended setup options (emulation
type and communication enhancement
section) to match the specification needs
between the printer and your computer —
Pages 33 to 56.
3. Select the printer driver from your
application software — Page 57.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
1. Introduction
Features
❏ Barcode Print available
• 13 resident barcode type
Industrial 2/5, Interleave 2/5, Codabar, Matrix 2/5, Code 11, Code 39,
Code 93, Code 128, EAN-8, EAN-13, UPC-A, UPC-E, Postnet
❏ Enlarged character printing
Characters can be enlarged (by up to 127 times as large x 127 times as
large) using the enlarged character command unique to this printer.
Software commands are used for control.
❏ Contain the 3 kind of emulations
Compatible to major printer emulations, Epson, IBM and Hewlett Packard printers.
•
•
•
EPSON
LQ-2550 compatible
IBM
2391 compatible
Hewlett Packard
Rugged Writer 480 (PCL3) compatible
❏ Wide selection of paper size
•
•
Single cut sheet papers
Fanfold continuous paper
A3, A4, B4, B5, Letter, Legal
5 - 16 inch wide and 2 - 16.5 inch long paper
•
•
Multi-part paper
Labeling paper
Original plus 5 copies
Label peel-proof capability
❏ Full option of font types and variation of character spacings
•
10 resident fonts
Courier, Prestige, Script, OCR-A, OCR-B, Gothic, Orator, Orator-S,
Roman, and Sans Serif
•
8 character spacings
10, 12, 15, 16.7, 17.1, 20, 24 characters per inch (CPI), and
proportional and 1/2 proportional characters
❏ Enlarge/reduce your layout to fit in any paper size
•
you can print the same layout of the document in different paper size.
❏ Easy operation
•
•
Multiple display language for international use.
Upside down display enables operation from the back of the printer.
❏ Superb compatibility and connectability
•
•
•
•
Communication protocols adjustable to any computer.
Interface connections provided for parallel, RS-232C.
Parallel and serial interface are switchted automatically when "AUTO" setting is selected.
Parallel interface complies with IEEE1284 Nibble mode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Options and expendables
The Cut Sheet Feeder greatly enhances the speed and
efficiency of document printing by feeding of up to 80 single
sheets of paper without reloading.
The Pull Tractor is recommended for applications using
extra thick forms.
Paper dimensions
Length: 14.5"~7.0"
Width : 15.0"~5.7"
Weight : 15~21 lbs.
Cut Sheet Feeder
1 Bin (#BP-78009)
2 Bin (#BP-78009E)
Pull Tractor (#BP-57008)
Matrix Print Head
Ribbon Cassette (#SBP-3051)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Power cord
One of the following plug types is supplied. See "Connecting the power cord" on page 12.
Please see the rating plate on the back of your printer for appropriate input voltage and consult your
dealer for a specific type of power cord, if necessary.
120V For USA
220-240V For Asia and Europe
240V For Australia
240V For U.K.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Printer description
Paper Guide
Platen
Ribbon Cassette
Paper Bail
Paper Select Lever
(Friction Lever)
Head Adjustment Lever
Printhead
Power Switch
Sound Seal Cover
Printer Cover
Paper Cutter
Paper Rack
Top Rear Cover
Operator Panel
Tractor Lock Lever
Rear Cover
Tractor Cover
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Precaution for extra-thick paper usage
Label fanfold paper may get jammed in the printer due to its stiffness and inflexibility. When using
such paper, set the paper rack in the slant position shown in the figure.
Push Tractor Method
Friction Feed Method
• Label Fanfold Paper
• Single ply Fanfold Paper
• Single Sheet Paper
• Multiple Fanfold Paper
Print Head
Print Head
Print Head
Platen
Tractor
Tractor
Friction Roller
Fanfold Paper
Description
Paper width
Paper length
Ply
Single-ply
Multiple Copies Label Paper
5~16 inch
2~16.5 inch
single
Original+5 max.
single
Total thickness
Paper weight
0.065~0.12mm 0.35mm max. 0.12mm max.
14lbs.~28lbs. non-carbon 125Kg max.
53g/m ~105g/m
2
2
Single Sheet Paper
Description
Single-ply
Paper size
Ply
A3, A4, B4, B5 Letter, Legal
single
Total thickness
Paper weight
0.08~0.12mm
17lbs.~28lbs.
64g/m2~105g/m2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Physical dimension(Model A)
24 .4" (620mm)
17.9"
(455mm)
19.9"
(505mm)
✽Paper Rack in flat position
(Continuous paper setting)
Sound Seal Cover
✽Paper Rack in upright position
(Single sheet setting)
17.1"
(435mm)
15.4"
(390mm)
✽Paper Rack in flat position
(Continuous paper setting)
11.6"
(295mm)
10.2"
(260mm)
12.0"
(305mm)
Weight: 44.1 lbs. (20 kg)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Physical dimension(Model B)
24.4" (620mm)
18.9"
(480mm)
20.9"
(530mm)
✽Paper Rack in flat position
(Continuous paper setting)
Sound Seal Cover
✽Paper Rack in upright position
(Single sheet setting)
17.1"
(435mm)
15.4"
(390mm)
✽Paper Rack in flat position
(Continuous paper setting)
11.6"
(295mm)
10 .2"
(260mm)
13.0"
(330mm)
Weight: 44.1 lbs. (20 kg)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
2. Setting up
Installing the paper rack
1. Slide both paper guides to the
extreme left and right edges of the
paper rack.
Pivots
Groove
2. With the two small pivots on either
side of the paper rack downward, fit
the pivots in the groove on the rear
top cover.
2
1
3. Place the paper rack in upright
position for single cut sheet paper
and lay it down for fanfold
continuous paper.
Rear Top Cover
Note
The paper guides should be placed to the outside edges during
the installation or removal of the paper rack.
Installing the sound seal cover
1. Lay the sound seal cover upside
down on the printer.
2. Fit one of the holes of the cover to
the stud of the L-angle hinge on one
side of the printer.
3. Fit the other hole to the other stud
by pressing the L-angle hinge
inward then out through the hole.
L-angle Hinge
Note
Make sure that both studs are out through the hole completely,
otherwise, the sound seal cover will be stuck in place.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
Installing the ribbon cassette
Turn OFF the printer's power and remove the used ribbon cassette, if necessary, by pulling straight
upward.
1. Open the printer cover.
2. Manually move the print head to the extreme right side of the printer for easy installation of the
ribbon. Do not try to move the print head if the power is on.
CAUTION
Do not touch the print head if the printer has been running for a long time. Wait until
the print head is cooled off.
3. Turn the ribbon feed knob in the direction of the arrow on the knob to remove any slack in the
ribbon.
Remove any slack from ribbon
Ribbon Feed Knob
4. Place the ribbon cassette on the left and right cassette holders, such that the ribbon rests on the
ribbon guide. Check to be sure that the ribbon drive shaft on the left cassette holder is inserted in the
hole on the bottom of the ribbon cassette.
5. Turn the ribbon feed knob in the direction of the arrow on the knob to remove any slack in the
ribbon.
6. Replace the front printer cover and set the head adjustment lever to the proper position for the best
print quality.
Ribbon Guide
Ribbon Mask
Cassette Holders
Cassette Holder
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
Connecting the computer
The printer has a parallel interface connector (Centronics) and a serial interface connector (RS232C).
Before you connect an interface cable to your computer, you need to know what type of printer
driver is supported by your software applications and what type of connector is needed to attach the
printer to the computer.
❏ Parallel Interface
36-pin plug
CAUTION
1
220-240V
120V
25
14
❏ Serial Interface
25-pin plug
13
1
25
14
Connecting the power cord
Check the power requirement printed on the rating plate on the rear of the printer before attaching
the power cord and turning on the printer. Both POWER and P.OUT lamps light up when the
printer is switched on correctly. The voltage selector should be set correctly as follows.
120V : USA, Canada
Voltage Selector
230V : Europe, Asia, Oceania
CAUTION
220-240V
120V
Note
For continued protection against risk of fire and
destruction of Power PCB Assembly, switch the
voltage selector according to using voltage.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
Loading the paper
❏ Fanfold continuous paper
1. Move the paper select lever
the fanfold paper setting.
toward the front of the printer to set
1
2
2. Set the print head adjustment lever
used for one-part paper. (See page 15)
.
In general, position 1 is
3. Remove the rear cover
of the printer or open the rear cover to
lock the cover in the open position.
4. Release the tractor lock levers
(upward), and move the right tractor to
the marked position as shown in the figure, and lock it in place.
5. Open both tractor covers and place the fanfold paper so that the tractor pins are aligned with the
holes in the paper. Carefully close both tractor covers.
CAUTION
Be careful not to catch your finger when closing the tractor covers.
6. After the paper is properly installed, re-adjust the left tractor to a position to keep the paper taut (but
not too taut) between the left and right tractors.
7. To load the paper, press the FF key on the front panel. The fanfold paper is fed to the top-of-form
position 14/60 inch (6mm) below the top edge of the paper. The top-of-form position can be
adjusted from 0/60 inch to 480/60 inches (8 inches = 203mm) in the basic setup options on page 31.
8. The paper bail automatically lowers to press the paper against the platen when the leading edge of
the paper feeds more than one inch onto the platen.
3
Rear Cover
Not Too Taut !!
5
Left Tractor Cover
Left Margin Marker
Right Tractor
Releasing direction
5
Tractor Cover
4
Tractor Lock Lever
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
❏ Single sheet paper
1. Move the paper select lever
sheet setting.
toward the rear of the printer to the single
1
2. Set the print head adjustment lever
for one-part paper. See page 15.
. In general, position 1 is used
2
3. Raise the paper rack to the vertical position and adjust the left
paper guide
used.
to the proper position for the size of the paper being
Note
If the paper is not loaded on the proper mark, the printer may
not detect the paper and will display PAPER ERROR.
4. Place single sheet paper against the paper rack and let it slide behind the platen.
5. Adjust the right paper guide
guides.
so that it comfortably holds the paper in between the two paper
Paper Size Marker
Extension Arm
4
Right Paper Guide
A3
B4
3
Left Paper Guide
6. Press the FF key to load the single sheet paper to the top-of-form position 14/60 inch (6mm) below
the top edge of the paper. The top-of-form position can be adjusted from 0/60 inch to 480/60 inches
(8 inches = 203mm) by using the front panel controls in the basic setup options on page 31.
Note
If the paper is not completely fed in, slightly push the paper downward. If it is still not fed in,
look in the TROUBLESHOOTING section.
7. The paper bail automatically lowers to press the paper against the platen when the leading edge of
the paper feeds more than one inch onto the platen.
Notes
1. Extension Arm
The extension arm is used to keep large size (Legal, B4) single sheets from falling behind the
paper rack. When using the extension arm, pull the arm until it clicks and locks in place.
2. TEAR OFF key is invalid with single sheet paper.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting up
❏ Paper alignment
Current print line location
The current printing line (DDD...) is the third line down from the top of the ribbon guide (line
spacing is 1/6 line: 6 LPI).
Ribbon Guide
C
C
C
D
D
C
D
D
Adjusting the print head position
The head adjustment is used to obtain the best print quality possible for the specific paper
being used. The print head position can be adjusted to accommodate printing on single and
multipart forms. When using multipart forms, move the print head adjustment lever toward the
front of the printer to widen the gap between the print head and the platen.
In general, position 1 is used for one-part paper. Moving the head adjustment lever one notch
adjusts the print head gap an amount corresponding to the addition of one more paper part.
Re-adjustment of the lever may be required depending on the quality of the actual printout:
If the ribbon smears on the paper, the gap is too narrow.
•
•
If the printed image is too light to read, the gap is too wide.
1 part-paper: 2nd click
6 part-paper: 9th click
1
(This scale is the suggested
1
5
6
9
number of sheets
for non-carbon part-paper.)
Head Adjustment Lever:
Move toward the front of
the printer for thicker paper
Notes
1. The print head adjustment lever should be set before loading the paper to avoid paper
jams.
2. If the printed image on the last copy of a multipart form is too light to read, set the
MULTIPART mode in the basic setup options (see page 26). This will increase the
striking intensity on multipart forms.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
3. Control panel and operations
Control panel and indicators
Standard Panel
LCD
Alternate up-side down reverse panel
LCD
Note: The alternate reverse panel installation instruction is described in Appendix D.
❏ Indicators
• Display window
Liquid Crystal Display (LCD)
Displays status and errors during operation and menus in the setup options.
The followings are some examples of the display messages.
Status message
P.OUT FANFOLD
COVER OPEN
This indicates that the printer is in offline and paper out status.
Warning message
This indicates that the printer cover is open. Close the cover to
resume the operation .
If the printer is in the offline mode, the following appears on the display.
FANFOLD 11 15
Status message for fanfold continuous paper
This column indicates the page length; and the paper widlh.
This indicates the type of paper selected is fanfold continuous
paper.
MANUAL: A4 P
Status message for single sheets paper
This indicates a paper size; B5 through A3 depending on the
designated paper size (default A4) selected in the setup options.
This indicates the type of paper selected is single sheet paper.
MANUAL, BIN 1, BIN 2, BIN 1+2
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
• Indicator lamps
Lamp
On
Off
Blinking
POWER
ONLINE
P.OUT
POWER
(green)
Power On
Power Off
—
ON LINE
(green)
Online
Offline
Cover open, or Head overheat
protection activating
ONLINE
P.OUT
(umber)
Out-of-paper Paper-in
Home sensor error, RAM error,
or paper error.
❏ Function Keys
•
ON LINE
Pressing this key places the printer offline so that the printer can perform
some functions independent from the host system. In the offline mode, data
is not received. When the printer is offline, pressing the key places the
printer online and ready to receive data from the host system.
ON LINE
•
RESET
When the RESET key is pressed, the printer immediately enters the reset
state and prepares for the initialize operation, which is nearly the same
initialize operation as when the power is turned on.
RESET
The following keys are active only in the offline mode:
•
LF/RLF
(Line feed and reverse line feed)
When the LF/RLF key is pressed, paper is fed per the line spacing at the 6
line per inch forward or backward, respectively.
While this key is pressed and held, the paper is continuously fed forward or
backward, respectively.
LF
RLF
•
FF
(Form feed)
Pressing this key feeds the paper to the next top of form position when the
paper is already loaded. Single sheet paper is fed to eject. Pressing this key
loads the paper when the paper is not loaded.
FF
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
•
M.LF/M.RLF
(Micro line feed/micro reverse line feed)
When the M.LF/M.RLF key is pressed, the paper is fed 1/360 inch forward
or backward, respectively. This key is used to set the paper position.
M.LF
M.RLF
To set the TOF SET (top-of-form set) function, press the FF key and then
simply advance the loaded paper forward or reverse to your desired print
position using the M.LF/M.RLF keys. Hereafter until you reload paper, the
first print position of the form is always fed at the same place.
•
TEAR OFF
[Used only for fanfold paper]
Pressing this key advances the perforation of the form to the paper cutter so
that the leading form can be torn off from the rest.
TEAR OFF
If this key is pressed after the form is torn off, the paper is fed backwards
and the mode is returned to offline. If the ON LINE key is pressed instead
of the TEAR OFF key, the paper is fed backwards and the mode is changed
to the online mode.
•
PARK
TOF SET
PARK
(Paper parking)
Pressing this key unloads the paper if the paper is already loaded.
Fanfold continuous paper (paper select lever in fanfold setting)
The paper is moved to the park station in the back of the printer by pressing
this key.
Single sheet paper (paper select lever in single sheet setting)
The paper in the print station will be ejected.
•
BIN
(ALT+SETUP keys)
This key is for selecting the active paper tray of the cut sheet feeder or the
paper feed type:MANUAL, BIN1, BIN2 or BIN1+2. BIN1, BIN2, BIN1+2
appears only when the cut sheet feeder (CSF) option is set.
BIN
EXIT
SETUP
+
Note
ENTER
ALT
The paper select lever must be switched to the single sheet setting.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
•
TOF SET
(ALT+PARK keys)
The TOF SET key is valid only when paper is loaded. When the TOF SET
key is pressed in the offline state, the TOF position is set to the top of the
ribbon guide, and the buzzer
TOF SET
PARK
sounds.
TOF Position
Ribbon Guide
+
After two seconds, the paper is
fed backward so that the TOF
position is at the current
ENTER
ALT
C
D
C
D
printing position.
C
D
C
D
When the TOF position is set,
the setting of “7 TOF ADJUST”
is changed to this set automatically.
*TOF:Top of form
•
•
SETUP
When the SETUP key is pressed the printer enters the setup options. The
setup options are explained later in the "Basic setup options" section.
BIN
EXIT
SETUP
QUALITY
This key is for selecting the print quality: LQ, NLQ, HQDR (high quality
draft), DRAFT, SD (speed draft), or SSD (super speed draft). To set your
desired print quality simply scroll and stop where your selection is
displayed. The printer beeps once for an acknowledgment.
QUALITY
Software commands can override the print quality setting of this key.
However, "#26 Quality Lock" option described on page 41 can lock-in the
ESC x 1
LQ is selected Draft is selected
ESC x 0
LCD
Graphic print speed
LQ
LQ
NLQ
LQ
LQ
S.D.
S.S.D.
Draft
Draft
HQDR
Draft
S.D.
Normal✽
High speed 1
High speed 2
High speed 2
High speed 2
High speed 2
NLQ
HQDR
DRAFT
S.D.
S.S.D.
S.S.D.
selection by this key and disable software commands.
This key also selects the graphic print speed.
*The graphic print speed is selected only by “31 GRAPHIC QUALITY”
in the extended setup options.
•
Others
The ←, →, ↓, ↑ EXIT and ENTER keys become effective only in the setup options entered by
pressing the SETUP key. For more information refer to "Basic setup options."
Control Levers
•
Head adjustment Lever
This lever adjusts the gap between the print head and the platen. The correct
gap adjustment for a different paper thickness is required to obtain optimum
print quality. See also page 15.
1
6
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
• Paper Select Lever
The paper select lever serves to switch between the fanfold continuous paper
setting and the single sheet paper setting (or CSF setting when CSF
installed).
Note: Switching this lever to continuous paper setting will mechanically
release the pressure roller for single sheets and engage gear trains for
continuous paper.
Paper parking
This function moves fanfold paper back to the push tractor position (park station) so that single
sheet paper can be used. Specifically it is useful when switching from fanfold paper to single
sheet paper.
•
•
•
Pressing the PARK key removes the fanfold paper from the print station so that single sheet
paper can be used.
Switching of the paper select lever is required for the actual mechanical switching of the paper
select.
Pressing the FF key when the printer is in the paper-out state loads the selected paper (fanfold
or single sheet) to the top-of-form position.
The following table explains the paper handling of the FF and the PARK key in the offline
state:
Friction Lever
P.OUT Lamp Function Key
Action
Autoload the paper
Ignore the key
Feed to the next TOF
Park the paper in the push tractor
Autoload the paper
Ignore the key
FF
PARK
ON
Continuous
Paper
FF
PARK
OFF
FF
PARK
ON
Single Sheets
FF
PARK
Eject the paper
Eject the paper
OFF
Notes
1. Make sure that the setting of the paper select lever corresponds to the type of paper being
used.
2. The paper park function causes PAPER ERROR in the following situations:
a) when the fanfold paper is not set in the park station (at the push tractors) after moving
more than 22 inches backward.
b) when the paper (fanfold or single sheet) is not autoloaded to the print station after
feeding more than 8 inches. (At this time, the printer tries to sense the paper in the
printer.)
c) when single sheet paper is not ejected from the printer after advancing more than 22
inches.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
Printing test pattern
Before performing the printer's self test, be sure the ribbon cassette and paper are properly
installed in the printer. The self test prints a continuous pattern of printable characters (ASCII
character pattern) in either draft or letter quality (LQ).
While test printing is executed, the ON LINE lamp blinks and the LCD indicates “SELF TEST”.
SELF TEST DRAFT
❏ To run the draft self test
Press the LF key while turning ON the printer's power. If the printer is already turned ON, the
draft self test may be performed by pressing the LF key together with the RESET key.
Keep pressing the LF key until the self test begins.
❏ To run the LQ self test
Press both the LF and ON LINE keys simultaneously while turning ON the printer. If the
printer is already turned ON, the LQ self test may be performed by pressing both the LF and
ON LINE keys simultaneously together with the RESET key.
Keep pressing the LF and ON LINE keys until the self test begins.
❏ To stop the self test temporarily
Press the ON LINE key to stop printing.
❏ To resume the self test
Press the ON LINE key again to restart printing.
❏ To terminate this function
Press the RESET key or turn off the power.
Note
Before initiating the self test, make sure that the width of the paper, especially fanfold paper
loaded in the printer corresponds to the setting selected in the extended setup options.
44 PAPER WIDTH
Maximum printable columns at 10cpi
....................
....................
....................
136 columns
80 columns
36 columns
WIDTH: 15 IN
WIDTH: 10 IN
WIDTH:
5 IN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
Demonstration print-out
To see what this printer can do, you may run this demonstration print-out (Letter or A4 paper
size) for checking the printer's performance. Press and hold the RLF and the M.RLF keys
while turning on the printer's power.
Tearing off a form
(Used only with fanfold continuous paper)
This function is activated by the TEAR OFF key and feeds fanfold paper so that the
perforation is aligned with the paper cutter located at the top rear of the printer, thus enabling
simple paper tearing. During the tear off
operation, the M.LF, and M.RLF keys are
used to correctly align the paper to the paper
cutter.
Paper Cutter
After tearing off the form, pressing the
TEAR OFF key a second time reversely
feeds the paper to the top of the next
available form.
Note
Pressing the TEAR OFF key (or the ONLINE key) the second time may return the paper to
the original print position when the top edge of the form does not pass above the paper
location prior to the first TEAR OFF operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Control panel and operations
Power-on operation summary
Operation (reference page)
Self test, draft (P21)
Self test,LQ (P21)
Hex dump, draft (P62)
Hex dump,LQ (P62)
Extended setup options (P33)
Demo printout (P22)
Loading MEMO 1 (P31)
Loading MEMO 2 (P31)
Loading MEMO 3 (P31)
Vertical alignment (P66)
EEPROM initialize 1
EEPROM initialize 2
Notes
1. Use either the RESET key or power switch when the circle is in both the RESET and
POWER columns.
2. EEPROM initialize 2 operation requires the vertical alignment operation after the
execution of the EEPROM initialize 2.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options
4. Basic setup options
About basic setup options
The setup options serve to define various initial states of the printer that are executed when the
power is turned on or when the RESET key is pressed. In addition, this mode serves to
redefine the font type, character spacing, and other parameters for the printer's current
operating conditions. The parameters set in the setup options are stored in the memory of the
printer and used as the default values in initialize operations.
❏ To set this option
When the SETUP key is pressed in the offline mode, the printer enters the function setup
option, where various functions can be set. The keys used in the function setup mode are
described below.
Exit setup to offline
Select menu
Select function
TOF SET
POWER
ON LINE
P.OUT
PARK
BIN
QUALITY
M.LF
LF
FF
MAIN SETUP
EXIT
ENTER
ALT
SETUP
M.RLF
RLF
TEAR OFF
ON LINE
RESET
Choose selected function
Exit setup to online
← and →
↓ and ↑
ENTER
EXIT
[Alternate to the PARK and QUALITY]
These keys are used to go over menus in the display, but cannot be used to select
a menu item.
[Alternate to the M.LF/M.RLF]
These keys are used to go over items within a menu in the display, but cannot be
used to set an item parameter.
[Alternate to the ALT]
When this key is pressed, an asterisk (*) indicating that the item is the currently
selected parameter is added at the end of the item.
[Alternate to the SETUP]
When this key is pressed, the content of the item is stored in the memory of the
printer. Then, the printer exits from the setup options and enters the offline
mode.
ONLINE
This key's function is similar to the EXIT key in that the printer saves the
selected item and exits from the setup options. At that time, if no errors or
irregular conditions exist, the printer enters the online mode.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options
❏ Selection procedure example
The following example illustrates the correct procedure to select a letter-portrait paper size
from the front panel:
1. Press the ON LINE key to enter the offline state. The ON LINE lamp is put out:
2. Press the SETUP key to enter the SETUP options. The LCD displays:
1 MULTIPART
3. Press the Right Arrow (→ ) key to select the menu and to display:
3 PAGE SINGLE
4. Press the Down Arrow ( ↓ ) key to step down the function items, and to display:
SIZE: LETTERp
5. Press the ENTER key to select letter-size portrait as the desired PAPER SIZE. The LCD
briefly displays the paper size with an asterisk at the end.
SIZE: LETTERp*
6. Press the EXIT key to store the selection, terminate the setup options, and return to the offline
state or press the ON LINE key to return to the on line state.
❏ Setup Memory
Current memory
The printer contains one current memory for automatically storing the preset setup states and
three user memories for storing data that is designated by the user.
The current memory automatically stores the configuration when the setup options are
terminated. When the power is turned on or when the RESET key is pressed, the printer
automatically sets the configuration per the current memory. Thus, when entering the setup
options, the contents of the current memory can be altered.
User memory
The user memories can store three different configurations. The user can set and recall the
contents of the memory to configure the printer. When the power is turned on or when the
RESET key is pressed, the contents stored in the user memories are not used as the initial
values. To use the contents of the user memories as the initial values, it is necessary to select
one of the user memories, MEMO 1 to MEMO 3, in the setup options and evoke the contents as
the preset condition.
To use the contents of the user memory as the current setup, it is necessary to display the “8
SELECT SETUP” on the menu and select one of the user memories. Exiting from the setup
options with a user memory selected will cause the contents of the user memory to be stored in
the current memory which then becomes the printer initial values.
To store a configuration in a user memory, display the “86 SAVE SETUP” selection in the
extended setup options and select one of the user memories. The current setup content is stored
in the specified memory when exiting the setup options.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (1-2)
Printing multipart paper
The multipart mode increases the print intensity on multipart forms.
1 MULTIPART
........... With one pass printing, normal speed
........... With one pass printing, reduced speed
........... With two pass printing
COPY: NORMAL
COPY: DARK 1
COPY: DARK 2
Selecting page length for fanfold paper
The page length selection varies from 2 inches to 16.5 inches with a 0.5 inch increment. The
page length is the same as the distance between two perforations.
The page length can be changed by software commands, but when the "Page Lock" option in
the extended setup options is set enabled, this page length selection becomes the fixed length
and software commands are ignored.
2 PAGE FANFOLD
PAGE: 2 IN
PAGE: ...
TOF(Top Of Form)
PAGE: 11 IN
PAGE: ...
PAGE: 16.5IN
Default page length is 11 inches
Printable area
Perforation
Printable area
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (3)
Selecting single sheet paper size
This function sets a paper size (page length, the right and left margins) of single sheet paper.
The "Page Lock" option in the extended options can lock-in the character spacing selected in
this option and ignores the related software command.
3 PAGE SINGLE
........... "P" denotes portrait.
........... "I" denotes landscape
........... Default page size is A4 portrait.
SIZE:
SIZE:
SIZE:
SIZE:
SIZE:
SIZE:
B5 p
B5 l
A4 p
A4 l
B4 p
B4 l
SIZE: LETTERp
SIZE: LETTERl
SIZE: LEGAL p
SIZE: LEGAL l
SIZE:
SIZE:
A3 p
A3 l
Note
A3 landscape can not be used with CSF.
Number of Lines / Page
item
EPSON/IBM
HP
Override OFF Override ON Override OFF Override ON
TOF Adj. TOF Adj. TOF Adj. TOF Adj.
0/60" 14/60" 0/60" 14/60" 0/60" 14/60" 0/60" 14/60"
Paper Size
B5 Portrait
B5 Landscape
A4 Portrait
1
1
1
68 68
98 98
80 80
238
163
278
191
345
238
261
197 8.5"
337 14"
197 8.5"
257
182
297
210
364
257
11"
56 55 58
38 37 40
65 64 67
45 43 47
81 80 83
56 55 58
61 60 63
46 45 48
79 78 81
46 45 48
94 93 96
65 64 67
56 56 55
39 38 37
66 65 64
45 45 43
82 81 80
56 56 55
62 61 60
47 46 45
80 79 78
47 46 45
95 94 93
66 65 64
60 59
43 41
70 69
49 48
86 84
60 59
66 64
51 49
84 82
51 49
99 98
70 69
A4 Landscape 1 114 114
B4 Portrait 98 98
B4 Landscape 1 136 136
Letter Portrait 82 82
Letter Landscape 1 108 108
Legal Portrait 82 82
Legal Landscape 1 136 136
A3 Portrait 1 114 114
A3 Landscape 1 136 136
1
1
1
401
278
420
297
CONDITIONS
•
•
•
•
•
Character Pitch: 10 CPI
Line Feed Pitch: 6 LPI
Page Length(in Epson/IBM) : = Paper form length - 0mm (top margin) - 17mm (bottom margin) - 2mm (tolerance)
Page Length and Number of Lines in HP depend on the TOF position and override function.
Right and Left Margin: correspond to the scale on the paper bail. (The unit is the number of characters).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (4)
Selecting font style
This selection is effective only in the LQ or NLQ print mode. There are 10 resident fonts
provided.
When the OCR-A or OCR-B font is selected, either 10 cpi or 12 cpi character spacing can be
selected. The "Font Lock" option in the extended options can lock-in the font selected in this
option and ignores the related software command.
4 FONT SELECT
........... Default font is Roman.
........... Sans Serif
FONT: ROMAN
FONT: S.SERIF
FONT: COURIER
FONT: PRESTIGE
FONT: SCRIPT
FONT: OCR-B
FONT: OCR-A
FONT: GOTHIC
FONT: ORATOR
FONT: ORATORs
Note:
1. If the current 'QUALITY' selection is SD, SSD, DRAFT, or
HQDR, the font selection depends on the EMULATION
currently selected:
HP mode — FONT SELECT selection is accepted and
QUALITY is automatically changed to LQ.
EPSON or IBM mode — FONT SELECT selection will not
take effect until QUALITY selection is changed to either
NLQ or LQ.
2. If the current 'CHAR PITCH' is set to 15, 16, 17.1, 20, or
24 and OCR-A or OCR-B is selected, the ROMAN font
will be automatically substituted.
PRINT SAMPLE
FONT
ROMAN
SANS SERIF
COURIER
PRESTIGE
SCRIPT
OCR-B
OCR-A
GOTHIC
ORATOR
ORATOR-S
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (5)
Selecting character spacing
This function selects one of the fixed spaced characters and proportional spaced characters.
The "Pitch Lock" option in the extended setup options can lock-in the character spacing
selected in this option and ignores the related software command.
When SD (speed draft) or SSD (super speed draft) is set the character spacing automatically
changes to 12 cpi or 15 cpi, respectively.
When OCR-A or OCR-B font is selected, either 10 cpi or 12 cpi can be selected.
5 CHAR PITCH
........... Default character spacing is 10 cpi printing
PITCH: 10 CPI
PITCH: 12 CPI
PITCH: 15 CPI
PITCH: 16.7 CPI
PITCH: 17 CPI
PITCH: 20 CPI
PITCH: 24 CPI
PITCH: PROP.
Letter Quality
Dot-spacing (V x H) Character structure (V x H)
Character pitch
10 cpi
1/180 X 1/360
1/180 X 1/360
1/180 X 1/360
1/180 X 1/720
1/180 X 1/720
1/180 X 1/720
1/180 X 1/720
1/180 X 1/720
1/180 X 1/720
1/180 X 1/360
1/180 X 1/720
24 X 36
24 X 30
16 X 24
24 X 36(+12)
24 X 36(+7)
24 X 36(+6)
24 X 30(+6)
16 X 24(+6)
24 X 24(+6)
24 X N
12 cpi
15 cpi (EPSON)
15 cpi (HP/IBM)
16.7 cpi
17 cpi
20 cpi
24 cpi (EPSON)
24 cpi (HP/IBM)
Proportional
1/2 Proportional
PITCH: 1/2PROP.
24 X N
Character Picth
10 CPI
Print Sample
12 CPI
15 CPI (EPSON )
15 CPI (HP/ IBM)
16.7 CPI
17.1 CPI
20 CPI
24 CPI(EPSON )
24 CPI (HP/ IBM)
Proportional
1/2 Proportional
The Proportional character width is twice the 1/2 Proportional width. In the Epson mode,
the print quality is changed to the high quality one. In the IBM or HP mode, print quality
does not change the print quality.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (6)
Enlarging/compressing print
Enlarges or compresses the text size.
Any setting other than 100% will cancel the double height printing mode. The relationships
between the paper sizes with their enlargement and compressing ratio are described below.
Note: The expansion displayed on the LCD has some allowance. Enlarged or reduced
characters are printed in a different font from the specified font.
ZOOM OUT
6 ZOOM IN/OUT
66%
79%
83%
ZOOM OUT: 66 %
ZOOM OUT: 79 %
ZOOM OUT: 83 %
ZOOM OUT: 91 %
NO ZOOM: 100 %
ZOOM IN: 116 %
ZOOM IN: 120 %
ZOOM IN: 141 %
ZOOM IN: 200 %
ZOOM IN: 400 %
ZOOM IN: 600 %
ZOOM IN: 800 %
ZOOM IN: 1000 %
ZOOM IN: 1200 %
ZOOM IN: 1400 %
ZOOM IN: 1600 %
B4 B5
A3 A4
A4 B5
B4 A4
A3 B4
ZOOM IN
120%
116%
141%
B5 A4
B4 A3
A4 B4
A4 A3
66%
79%
83%
91%
100%
116%
120%
141%
4 point character size
200%
400%
600%
800%
1000%
1200%
1400%
1600%
Note: This sample illustrates only a scale image.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (7-8)
Setting top of form position
The top-of-form (TOF) can be set using this function, anywhere from a minimum of 0 inch to a
maximum of 480/60 inches (8 inches = 203mm) by increments of 1/60 inch.
Press the Up or Down arrow keys to increase or decrease the TOF setting, respectively. Press
the ENTER key to select the desired setting.
7 TOF ADJUST
TOF: + 0/60IN
TOF: +nnn/60IN
TOF: +480/60IN
........... Defaults to 14/60 inch
Note: Any improper setting of TOF position will set it back to the default value. The top of
form differs from the top margin in that the top of form determines the first line of the print
station where the top margin can be moved anywhere between the top of the form and the
bottom margin. See "40 TOP MARGIN" on page 47.
Note
When using settings less then 14/60", the printer is more susceptible to a paper jam,
depending on forms type being used.
Loading user & factory setup options
Loads one of three user designed setup options to the current active memory. This will erase
and replace setup contents in the current memory. The printer has three setup storage areas that
can store different setups. If you need to save the current setups before replacement, it is
necessary to select the “86 SAVE SETUP” item in the extended setup options on page 56.
8 SELECT SETUP
Equivalent short cut operation can be performed when:
SETUP: MEMO 1
SETUP: MEMO 2
SETUP: MEMO 3
SET.: FACTORY
........... pressing the PARK key with the RESET key,
........... pressing the QUALITY key with the RESET key,
........... pressing the M.LF key with the RESET key.
Note: When this setting is executed, the printer will be initialized.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Basic setup options (8)
Factory Default Setting
Option Menu
Factory Default
Option Menu
Factory Default
38 PCL MODE
PCL3+
LINE-DRAW
0 LINE
0 LINE
0 COLUMN
0 COLUMN
15 INCH
NO SCROLL
YES
<Basic options>
1 MULTIPART
NORMAL
11"
A4 PORTRAIT
ROMAN
10 CPI
100%
14/60 INCH
39 CHR TB2 HP
40 TOP MARGIN
41 BOTTOM MARGIN
42 LEFT M.
2 PAGE FANFOLD
3 PAGE SINGLE
4 FONT SELECT
5 CHAR PITCH
6 ZOOM IN/OUT
7 TOF ADJUST
43 RIGHT M.
44 PAPER WIDTH
45 AUTO SCROLL
46 OVERRIDE BM
47 LABEL MODE
48 P.OUT DTCT
49 CSF OPTION
50 SCROLL POS
51 LF SPEED
60 INTERFACE
61 SLCT IN CMD
62 PARITY BIT
63 DATA LENGTH
64 STOP BIT
NO
<Extended options>
10 EMULATION
11 CHR TB HP
12 CHR TB EPSON
13 CHR TB IBM
14 NATIONAL FONT
15 CODE PAGE
16 AGM IBM
17 CR SETTING
18 LF SETTING
19 LF PITCH
20 ZERO STYLE
21 TABULATION
22 PAGE LOCK
23 QUALITY
24 FONT LOCK
25 PITCH LOCK
26 QLTY LOCK
27 BC/L.CHR
28 BC TYPE
29 BC SIZE
30 LARGE CH.SIZE
31 GR QLTY
32 ACCENT CHR
33 FF CODE/TOF
EPSON
ROMAN-8
ITALIC
SET 1
USA
ANY POS
NOT INSTALLED
ANY POS
NORMAL
PARALLEL
NO
NON
8 BITS
1 BIT
437(USA)
NO
CR ONLY
LF+CR
6 LPI
NO-SLASHED
8 CHAR.
NO
LQ
NO
NO
NO
65 PROTOCOL
66 BAUD RT
DTR
9600 BPS
PRINT *
NO
NO
NO
67 SERIAL ERROR
68 CTS ENABLE
69 CD ENABLE
70 DSR ENABLE
71 BUFFER SIZE
72 BUSY/ACK
73 DATA LATCH
74 ERROR STATUS
80 PRINT DIR
81 DISPLAY LANG
82 INVERT DISP
83 SOFTWARE SET
84 RESET LOCK
85 SLEEP MODE
64 KB
TYPE 2
TYPE F
YES
BI-DIRECTION
ENGLISH
NO
YES
NO
YES
MODE 1
CODE39
1
8
MODE 2
SIMPLE
YES
Option Menu
CURRENT
MEMO1
MEMO2
MEMO3
<Basic options>
4 FONT SELECT
ROMAN
COURIER
COURIER
COURIER
<Extended options>
10 EMULATION
18 LF SETTING
32 ACCENT CHR.
38 PCL MODE
EPSON
LF+CR
SIMPLE
PCL3+
NO
HP
HP
IBM
LF ONLY
COMPO.
PCL3+
NO
LF ONLY
COMPO.
PCL3
NO
LF ONLY
SIMPLE
PCL3+
YES
61 SLCT IN ENBL
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options
5. Extended setup options
About extended setup options
The extended setup options contain various setup options which are used less frequently than
the basic setup options. The function in these options are categorized to four functional blocks:
Items numbering in 10's through 30's are for "Print enhancement" which defines the emulation
type or character tables.
Items numbering in 40's and 50's are for "Paper handling enhancement" which defines the paper
characteristics or print area.
Items numbering in 60's and 70's are for "Communication enhancement" which defines the
interface control parameters.
Items numbering in 80's are for other functional items to "Miscellaneous".
For the overview of the extended setup options, refer to the extended setup options summary on
page 34 and 35.
•
•
•
•
Note: You may have noticed that some option numbers are skipped in the display. Those
skipped item numbers are reserved for special use and they do not affect regular operation of
this printer.
❏ To set this option
By pressing and holding the SETUP key when the RESET key is pressed, the printer enters the
extended setup options, where various functions including the basic setup options can be set.
The keys and operation method in the extended setup options are the same as those in the basic
setup options. However, when exiting from the extended setup options, the initialization of the
printer will be conducted by printing the RESET key.
Select menu
Select function
Exit setup to offline
TOF SET
POWER
ON LINE
P.OUT
PARK
BIN
QUALITY
M.LF
LF
FF
EXTENDED SETUP
EXIT
ENTER
ALT
SETUP
M.RLF
RLF
TEAR OFF
ON LINE
RESET
Store selected function
Enter extended setup options
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options
Extended setup options summary
Press both the SETUP and RESET keys to enter the extended setup options.
GBasic setup options #1-#8 GExtended setup options #1-#87
1
2
3
5
6
4
PAGE LENGTH
(FANFOLD)
FONT SELECT
PAGE LENGTH
(SINGLE)
CHARACTER
PITCH
ZOOM IN/OUT
MULTIPART
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
B5 PORT
B5 LAND
A4 PORT *
A4 LAND
B4 PORT
66
79
83
91
100 % *
116
120
141
200
400
600
%
%
%
%
ROMAN *
SANS SERIF
COURIER
PRESTIGE
SCRIPT
OCR-B
OCR-A
GOTHIC
ORATOR
10 CPI *
12 CPI
15 CPI
16.7CPI
17.1CPI
20 CPI
24 CPI
PROPORTIONAL
1/2 PROPORTIONAL
NORMAL *
DARK 1
10
10.5
11*
11.5
12
12.5
13
13.5
14
14.5
15
DARK 2
B4 LAND
%
%
%
%
%
%
%
%
%
%
%
LETTER PORT
LETTER LAND
LEGAL PORT
LEGAL LAND
A3 PORT
ORATOR-S
A3 LAND
800
15.5
16
16.5
The asterisk (*) indicates
the factory default setting.
1000
1200
1400
1600
9.5
7
8
10
11
EMULATION
CHARACTER
TABLE (HP)
TOF
ADJUSTMENT
IRV
ITALY
SELECT SETUP
MEMORY
SWEDEN1
SWEDEN2
SPAIN
FRANCE
GERMAN
U.K.
PORTUGAL
NORWAY1
NORWAY2
FRANC2
GERMAN2
SPAIN2
SPAIN3
JAPAN
EMULATION MODE
EPSON *
IBM
EMULATION MODE
ROMAN-8 *
CODE PG
PC-8D/N
ECMA
TOP OF FORM
+ n/60 inches
MEMO 1
MEMO 2
MEMO 3
FACTORY
HP
0
≤ n ≤ 480
PORTUGAL2
Default: n=14
LEGAL
12
13
15
14
16
CHARACTER
TABLE (EPSON)
CHARACTER
TABLE (IBM)
NATIONAL
FONT
CODE PAGE
AGM
(IBM)
CHARA.TABLE
ITALIC *
GRAPHICS
DOWNLOAD
CODE PAGE
NATIONAL FONT
USA *
FRANCE
GERMANY
U.K.
DENMARK
SWEDEN
CHARA. TABLE
CHAR.SET1 *
CHAR.SET2
ALTERNATE GRAPHIC
NO *
YES
863:CANADIAN-FRENCH
865:NORWAY
BRASCII
CODE PAGE
437:USA *
850:MULTILINGUAL
857:TURKEY
858
SPAIN
JAPAN
NORWAY
DENMARK2SPAIN 2
LATIN AMERICA
KOREA
TURKEY
LEGAL
860:PORTUGAL
861
ABICOMP
ISO-8859-1
ITALY
18
17
20
21
22
19
LF SETTING
CR SETTING
LF PITCH
ZERO STYLE
TABULATION
PAGE LENGTH
LOCK
TABULATION
LF SETTING
LF ONLY
LF+CR *
PITCH
6 LPI *
8 LPI
9 LPI
3 LPI
4 LPI
CR SETTING
CR ONLY *
CR+LF
ZERO STYLE
NO-SLASHED *
SLASHED
PAGE LOCK
NO *
YES
2
4
6
8
CHAR.
CHAR.
CHAR.
CHAR.*
AUTOFEED
10 CHAR.
12 CHAR.
27
24
25
28
23
26
BARCODE/
ENLARGED
CHARACTER
BARCODE
TYPE
QUALITY
FONT LOCK
QUALITY LOCK
PITCH LOCK
BC/L.CHR
IGNORED
MODE1 *
MODE2
QUALITY TYPE
LQ *
NLQ
PITCH LOCK
NO *
YES
FONT LOCK
NO *
YES
BARCODE TYPE
INDSTRIAL 20F5
INTERLEAVED 20F5
MATRIX 20F5
CODABAR
CODE11
CODE39*
CODE93
CODE128
QUALITY LOCK
NO *
YES
HQDR
DRAFT
S.D
S.S.D.
EAN13
UPC-A
UPC-E
POSTNET
ELEMENT
29
31
32
30
EAN8
GRAPHIC PRINT
MODE
ENLARGED CHAR
SIZE
ACCENT CHAR
BARCODE
SIZE
PRINT SPEED
MODE1
MODE2*
PRINT METHOD
SIMPLE*
COMPO
1*
1.5
2
1
2
4
MODE3
2.5
8*
12
16
24
32
Next page
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options
Previous page
40
36
35
39
38
34
37
41
33
42
CHR TB2 HP
PCL MODE
FF CODE
AT TOF
TOP MARGIN
LEFT MARGIN
BOTTOM MARGIN
2ND CHARACTER TABLE
BOTTOM MARGIN
+ n LINE
LEFT MARGIN
+ n COLUMN
TOP MARGIN
+ n LINE
VALID
YES*
NO
PCL MODE
PCL3+ *
PCL3
LINE DRAW *
MATH-7
0
n
15
0
n
63
0
n
15
DEFAULT: n=0
DEFAULT: n=0
DEFAULT: n=0
PCL3+D
45
47
48
43
44
46
FANFOLD
PAPER WIDTH
RIGHT MARGIN
LABEL MODE
AUTO SCROLL
P.OUT
DETECTION
OVERRIDE BM
AUTO SCROLL
NO SCROLL *
0.5 SEC
1 SEC
RIGHT MARGIN
+ n COLUMN
WIDTH
LABEL MODE
NO *
YES
DETECTION
ANY POS*
PAGE END
OVERRIDE
NO
YES *
15 INCH *
10 INCH
5 INCH
0
n
63
DEFAULT: n=0
5 SEC
10 SEC
15 SEC
49
51
50
60
62
61
CSF OPTIONS
LF SPEED
AUTO SCROLL
VALID POSITION
SELECT IN
CMD
INTERFACE
PARITY BIT
LF SPEED
NORMAL*
1/2
CSF TYPE
NOT INSTALLED *
SINGLE
DOUBLE
INTERFACE
PARALLEL*
SERIAL
SELECT IN COMMAND
YES
NO *
I/F
ANY POS *
TOF ONLY
PARITY
NONE *
EVEN
AUTO
ODD
64
65
68
67
63
66
CTS ENABLE
DATA LENGTH
STOP BIT
PROTOCOL
SERIAL ERROR
BAUD RATE
CTS SIGNAL
NO *
YES
PROTOCOL
DTR *
XON/XOFF 1
XON/XOFF 2
ETX/ACK
ERROR
PRINT *
IGNORED
BAUD RATE
38400 BPS
19200 BPS
9600 BPS *
4800 BPS
2400 BPS
1200 BPS
600 BPS
LENGTH
8 BITS *
7 BITS
STOP BIT
1
2
BIT *
BITS
300 BPS
73
74
69
72
70
71
DATA LATCH
TIMING
ERROR
STATUS
DSR ENABLE
BUFFER SIZE
BUSY /ACK
TIMING
CD ENABLE
STROBE
TYPE F.*
TYPE R.
STATUS SIGNAL
YES*
NO
BUFFER
64KB *
8KB
TIMING
TYPE 1
TYPE 2 *
TYPE 3
CD SIGNAL
NO *
YES
DSR SIGNAL
NO *
YES
128B
80
84
83
85
81
82
PRINT
DIRECTION
RESET KEY
LOCK
SOFT WARE
SETUP
SLEEP MODE
DISPLAY
LANGUAGE
INVERT
DISPLAY MODE
SOFTWARE
COMMAND
NO
LCD LANGUAGE
ENGLISH *
DEUTSCH
FRANCAIS
ESPANOL
RESET KEY LOCK
NO *
YES
SLEEP
YES*
NO
INVERT
NO *
YES
DIRECTION
PRE-DIRECTION
UNI-DIRECTION
BI-DIRECTION *
YES *
ITALIANO
87
86
SETUP MENU
LIST
SAVE SETUP
LIST
SAVE
MAIN *
MEMO 1
MEMO 2
MEMO 3
EXTENDED
ALL SETUP
FACTORY
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (10-11)
Print enhancement
Emulation
The desired emulation mode of the printer can be selected using this function.
10 EMULATION
EML: EPSON
EML: IBM
EML: HP
........... Epson LQ-2550 compatible
........... IBM 2391 compatible
........... RuggedWriter 480 compatible
Character table (HP mode)
This function selects one of character sets provided in the HP emulation.
11 CHR TB HP
PCL3, PCL3+, PCL3+D mode
ROMAN-8 (8U)
CODE PAGE
PC-8 (11U)
(ISO 8859-1,0N)
(HP SET,1U)
(ISO-10,0S)
(ISO-11,3S)
(ISO-17,2S)
(ISO-69,1F)
(ISO-21,1G)
(ISO-4,1E)
TBL: ROMAN-8
TBL: CODE PG
TBL: PC-8D/N
TBL: ECMA
TBL: LEGAL
TBL: SWEDEN1
TBL: SWEDEN2
TBL: SPAIN1
TBL: FRANC1
TBL: GERMAN
TBL: U.K.
TBL: PORTU1
TBL: NORWAY1
TBL: NORWAY2
TBL: IRV
TBL: ITALY
TBL: FRANC2
TBL: GERMN2
TBL: SPAIN2
TBL: SPAIN3
TBL: JAPAN
TBL: PORTU2
Setup menu #15 CODE PAGE:
CODE PAGE 437 PC-8(10U)
CODE PAGE 850 PC-850(12U)
CODE PAGE 857 TURKEY
CODE PAGE 858 EURO SYMBOL
CODE PAGE 860 PORTUGAL
CODE PAGE 861 ICELANDIC
CODE PAGE 863 CANADIAN-FRENCH
CODE PAGE 865 NORDIC
CODE PAGE BRASCII
CODE PAGE ABICOMP
ISO-8859-1
(ISO-16,4S)
(ISO-60,0D)
(ISO-61,1D)
(ISO-2,2U)
See page 38
(ISO-15,0I)
(ISO-25,0F)
(HP SET,OG)
(HP SET,1S)
(ISO-85,6S)
(ISO-14,0K)
(ISO-84,5S)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (12-13)
Character table (Epson mode)
This function selects one of character sets provided in the Epson emulation.
12 CHR TB EPSON
........... Sets italic table (see page 127)
........... Sets graphic table (see page 127)
........... Sets user defined download table
........... This selection replaces the ASCII character area 80h-FFh
with the code page selected in "15 CODE PAGE"
TBL: ITALIC
TBL: GRAPHIC
TBL: DOWN LD
TBL: CODE PG
Character table (IBM mode)
This function selects between the IBM character set 1 and set 2.
Refer to the character set tables in Appendix C.
13 CHR TB IBM
........... Sets IBM character set 1 table (see page 128)
........... Sets IBM character set 2 table (see page 129)
TBL: SET 1
TBL: SET 2
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (14-15)
National font style
One of the following 16 national fonts can be selected.
ASCII HEXADECIMAL
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
14 NATIONAL FONT
CNTRY: USA
CNTRY: FRANCE
CNTRY: GERMANY
CNTRY: U.K.
CNTRY: DENMRK
CNTRY: SWEDEN
CNTRY: ITALY
CNTRY: SPAIN
CNTRY: JAPAN
CNTRY: NORWAY
CNTRY: DNMRK 2
CNTRY: SPAIN 2
CNTRY: LATN AM
CNTRY: KOREA
CNTRY: TURKEY
CNTRY: LEGAL
Code page
The default code page can be selected using this function. Refer to the code page table in
Appendix C.
15 CODE PAGE
........... USA (see page 133)
........... Multilingual (see page 133)
........... Turkey (see page 133)
........... Multilingual Euro symbol(see page 134)
........... Portugal (see page 134)
........... Icelandic (see page 134)
........... Canadian-French (see page 134)
........... Norway (see page 135)
C.P.: 437
C.P.: 850
C.P.: 857
C.P.: 858
C.P.: 860
C.P.: 861
C.P.: 863
C.P.: 865
........... BRASCII (see page 135)
........... ABICOMP (see page 135)
........... ISO-8859-1(see page 135)
C.P.:
C.P.:
C.T.: ISO-1
BRASCII
ABICOMP
38
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (16-18)
IBM Alternate graphic mode (AGM) (Valid in IBM mode)
This function enables the IBM emulation to work similar to the Epson emulation in high
density graphics. The table below describes the differences in their related control codes.
16 AGM IBM
AGM: NO
AGM: YES
Command
AGM: NO
AGM: YES
ESC 3 n
ESC J n
ESC A n
ESC *
Set n/216" line spacing
Line feed n/216"
Set n/72" line spacing
Not supported
Set n/180" line spacing
Line feed n/180"
Set n/60" line spacing
Set various graphic modes
Carriage return (CR)
A carriage return (ASCII code 0Dh or 13) causes data in the buffer to be printed and the
carriage to be moved to the left most print position at the same line. The following option can
be selected when issuing a carriage return. Refer to the specification of your application for
correct selection.
17 CR SETTING
........... Carriage return without a line feed
........... Carriage return with a line feed
........... Autofeed signal enabled
CR: CR ONLY
CR: CR+LF
CR: AT FEED
Note: Autofeed is effective for the system using parallel interface with AUTO FEED signal to
control the the carriage return with or without a line feed. The autofeed signal must be low
when the printer is initialized in order to add a line feed to every CR code.
Line feed (LF)
This function selects whether to execute the carriage return operation when receiving the line
feed command (LF code).
18 LF SETTING
........... Line feed without a carriage return
........... Line feed with a carriage return
LF: LF ONLY
LF: LF+CR
39
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (19-22)
Line feed spacing
This function selects the default line feed spacing. When no line feed spacing is set in the
software command, this value is used as a linefeed.
19 LF PITCH
LF: 6 LPI
LF: 8 LPI
LF: 9 LPI
LF: 3 LPI
LF: 4 LPI
Slashed zero
The zero style is selected as either “0” (no-slash) or “Ø” (slashed).
20 ZERO STYLE
........... “0” (no-slash) is selected
........... “ ” (slashed) is selected
ZERO: NO-SLSH
ZERO: SLASHED
Ø
Set default tab stops
The default horizontal tab stops are selected from different tab intervals. This tab setting
becomes effective when the printer receives tab commands from the host system.
21 TABULATION
TAB:
TAB:
TAB:
TAB:
2 CHAR
4 CHAR
6 CHAR
8 CHAR
TAB: 10 CHAR
TAB: 12 CHAR
Lock-in the page length
The page length and the top and bottom margins set on the front control panel are locked-in.
Any page layout related software command cannot override this setting.
22 PAGE LOCK
LOCK:
LOCK:
YES
NO
40
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (23-26)
Print quality
The letter or draft quality printing or their variations can be selected. This function performs
the same way as when the QUALITY key is pressed on the front control panel.
This function selects the graphic print speed. See the page 19.
23 QUALITY
QLTY: LQ
........... Letter quality printing
........... Near letter quality printing
........... High quality draft printing
QLTY: NLQ
QLTY: HQDR
QLTY: DRAFT
QLTY: S.D
QLTY: S.S.D
........... Speed draft printing (12cpi)
........... Super speed draft printing (15cpi)
Lock-in the font
The character font set in the "Selecting font style" option on page 28 are locked-in, so any
character font related software command cannot override this setting.
24 FONT LOCK
LOCK:
LOCK:
YES
NO
Lock-in the character spacing
The character spacing set the "Selecting character spacing" option on page 29 are locked-in, so
any character spacing related software command cannot override this setting.
25 PITCH LOCK
LOCK:
LOCK:
YES
NO
Lock-in the print quality
The print quality set the "print quality" option on page 41 are locked-in, so any print quality
related software command cannot override this setting.
26 QLTY LOCK
LOCK:
LOCK:
YES
NO
41
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (27-28)
Bar code print enhancement
Enable Bar code print and Enlarged character
This function enables the printer to accept the control commands of the barcode and enlarged
character.
27 BC/L. CHR
........... ESC SO and ESC SI can not be used for the bar code data start or stop command.
........... ALL control command are valid.
........... Bar code and Enlarged character are invalid.
BC:
BC:
BC:
MODE 1
MODE 2
IGNORED
Codabar
Bar code type
This function selects a type of bar code.
Bar code type element enables you to
print bar codes by varying the width of the
narrow bar, wide bar, narrow space,
wide bar, or intercharacter gap.
See Appendix B, "Bar code control
code" for details.
CODE 11
CODE 39
CODE 93
CODE 128
EAN-8
28 BC TYPE
*
*
TYPE: INDST25
TYPE: INTRL25
TYPE: MATRIX
TYPE: CODABA
TYPE: CODE11
TYPE: CODE39
TYPE: CODE93
TYPE: C128
TYPE: EAN-8
TYPE: EAN-13
TYPE: UPC-A
TYPE: UPC-E
TYPE: POSTNET
TYPE: ELEMENT
EAN-13
UPC-A
UPC-E
Industrial 2 of 5
Interleaved 2 of 5
Matrix 2 of 5
POSTNET
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (28)
❏ Bar code specifications
The table below shows the specifications of thirteen types of bar codes available for the printer. Bar
code printing examples are shown on the previous page.
Remark
Check character
Bar code
Industrial 2/5
Structure ICG letters (#)
Sample data
1234567
5B4S
Yes
0-9
Yes
(Mod 10)
Yes
Even number, including
check character. Data
length is variable.
Interleaved 2/5
5B5S
No
0-9
1234567
(2 characters
as one unit)
(Mod 10)
Start and end codes are
sent by the user.
Codabar
Matrix 2/5
Code 11
Code 39
Code 93
Code 128
EAN-8
4B3S
3B2S
3B2S
5B4S
3B3S
3B3S
2B2S
2B2S
2B2S
2B2S
2LB3SB
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
0-9,
Yes
(Mod 16)
Yes
1234567
1234567
Special
characters: 24
0-9
(Mod 10)
Yes
Start and end codes are (
code. Dual check character
Start and end codes are
asterisk (*) codes.
)
0-9,"-"
1234567
(Mod 11)
Yes
0-9,
AB,...(43)
ASCII
(128)
1234567
(Mod 43)
Yes
Two check characters
1234567
(Mod 47)
Yes
ASCII
(128)
1234567
(Mod 103)
Yes
8 digits (2 prefix code +5
0-9
4912345
data code+Check character)
13 digits (2 prefix code +10
data code+Check character)
12 digits (NSC+10 data+
Check character)
UPC-A (12-digit) data is
automatically converted into
UPC-E (10-digit) data.
(Mod 10)
Yes
EAN-13
UPC-A
0-9
0-9
0-9
0-9
491234567890
01234500006
01234500006
123456789
(Mod 10)
Yes
(Mod 10)
Yes
UPC-E
(Mod 10)
Yes
6, 10 or 12 digits
Postnet
(data +Check character)
(Mod 10)
"B" and "S" in the "Structure" column show the number of bars
and spaces which consist of one or two characters. LB and SB
mean long bar and shot bar, respectively.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (29-30)
Bar code size
This function specifies the default bar code size.
29 BC SIZE
BC SIZE: 1
BC SIZE: 1.5
BC SIZE: 2
BC SIZE: 2.5
The tables below show bar code sizes and attributes.
SIZE
1
1.5
2
2.5
NARROW BAR
WIDE BAR
2/120inch 3/120inch 4/120inch 5/120inch
6/120inch 9/120inch 12/120inch 15/120inch
NARROW SPACE 2/120inch 3/120inch 4/120inch 5/120inch
WIDE SPACE 6/120inch 9/120inch 12/120inch 15/120inch
INTER CHARA.GAP 2/120inch 3/120inch 4/120inch 5/120inch
BAR HEIGHT
8/12inch 8/12inch 12/12inch 12/12inch
HRI PRINT
HRI FONT
BELOW
OCR-B
CHECK CHARACTERS Added
PRINT DENSITY
1/120 inch
Enlarged character size
This function specifies the default size of enlarged characters.
30 LARGE CH.SIZE
SIZE : 1
SIZE : 2
SIZE : 4
SIZE : 8
SIZE : 12
SIZE : 16
SIZE : 24
SIZE : 32
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (31-33)
Graphic Print Speed
This function selects the print speed of the 120 DPI/240DPI and 180 DPI/360DPI graphics.
31 GR QLTY
QLTY: MODE1
QLTY: MODE2
QLTY: MODE3
120/240DPI
180/360DPI
SPEED Min.Dot pitch SPEED Min.Dot pitch
MODE1 15.7IPS 1/120"
MODE2 18.0IPS 1/120"
MODE3 31.5IPS 1/60"
10.5IPS 1/180"
18.0IPS 1/120"
24IPS 1/60"
Accent character
This function specifies the method of printing accent characters.
32 ACCENT CHR.
........... The accent character of the resident font is printed.
........... The accent symbol and the character are printed
........... separately to add the accent symbol in the proper position.
PRINT:SIMPLE
PRINT:COMPO
Setting of the FF (Form Feed) code at TOF
33 FF CODE / TOF
FF CODE/TOF:YES
FF CODE/TOF:NO
Establish the setting whether or not FF(Form Feed) is to be executed.
When "YES"is set, the FF code performs Form Feed even if the present position is at TOF.
When "NO" is set, the FF code is ignored when the present position is at TOF.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (38-39)
HP mode enhancement
PCL Mode (HP mode)
This function selects the emulation level in HP mode.
38 PCL MODE
MODE: PCL3+
MODE: PCL3
MODE: PCL3+D
Fully compatible with the Rugged Writer 480. The character pitches(15, 17.1 and 24)
and print quality modes (HQDR, NLQ, S.D., S.S.D.) cannot be selected by software
commands.
PCL3
PCL3+
Extra capability to the Rugged Writer 480. In this mode, additional character pitches,
print quality modes, and raster graphics resolutions may be selected by software
command.
Limited DESK-JET compatibility. In this mode, the commands "ESC * p # Y" and
"ESC * p # X" define units in 1/360".
PCL3+D
If you want print DESK-JET application data, you can make use of PCL3+D. The print
position and graphics of the PCL3+D are closer than the other two modes to the DESK
JET.
Secondary character table (HP mode)
This function selects symbol set of the secondary font table.
39 CHR TB2 HP
........... Line draw
........... MATH-7
TBL:
TBL:
LINE
MATH
46
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (40-42)
Paper handling enhancement
Set the top margin
This function sets the top margin by lines with fixed line spacing of 6 lines per inch in the
range between 0 to 15 lines (2.5") from the top of the form.
40 TOP MARGIN
T.M.: 0 LINE
T.M.: nn LINE
T.M.: 15 LINE
Set the bottom margin
This function sets the bottom margin by lines with fixed line spacing of 6 lines per inch in the
range between 0 to 15 lines (2.5") from the bottom edge of the form.
41 BOTTOM MARGIN
Note
The bottom edge of the form is determined by the page
length or the paper size set by the PAPER key in the
front control panel or in the associated paper size
options in the basic setup options. See the paper size
table on page 27.
B.M.: 0 LINE
B.M.: nn LINE
B.M.: 15 LINE
Set the left margin
This function sets the left margin by columns with fixed character spacing of 10 characters per
inch in the range between 0 to 63 columns (6.3") from the left-most printable location.
Left most printable location
Left most printable location
42 LEFT M.
Left Margin
Left Margin
0 - 63 columns
0 - 63 columns
L.M.: 0 COL
L.M.: nn COL
L.M.: 63 COL
Print Area
Print Area
Print Area
47
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (43-45)
Set the right margin
This function sets the right margin by columns with fixed character spacing of 10 characters
per inch in the range between 0 to 63 columns (6.3") from the right-most printable location.
Right most printable location
Right most printable location
43 RIGHT M.
Right Margin
Right Margin
0 - 63 columns
0 - 63 columns
R.M.: 0 COL
R.M.: nn COL
R.M.: 63 COL
Print Area
Print Area
Note
Print Area
The right edge of the form is
determined by the paper size set
in the stup options on page 27 or
the paper width set in the setup
options on this page.
Fanfold paper width
This function sets the paper width to be used in the printer. Depending on the paper width, the
print head will shift to the one half of the print width selected in this function to properly hold
the paper in place, and eliminates the possibility of paper jams during loading.
44 PAPER WIDTH
Maximum printable column at 10 cpi
...........
...........
...........
136 columns
80 columns
36 columns
WIDTH: 15 IN
WIDTH: 10 IN
WIDTH:
5 IN
Autoscroll delay
The Autoscroll function automatically advances the paper to the tear off position when no data
exists in the communication buffer and no new data is received for a period of 0.5, 1, 5, 10, or
15 seconds.
The printer automatically aligns the paper to the top of the next form when data is received.
This feature is very beneficial when it is necessary to print a single invoice, and tear it off
immediately following printing.
45 AUTO SCROLL
NO SCROLL
SCROLL: 0.5SEC
SCROLL: 1 SEC
SCROLL: 5 SEC
SCROLL: 10 SEC
SCROLL: 15 SEC
Note
Autoscroll becomes invalid when the label protect mode is
set active.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (46)
Override bottom margin
The effect of this function varies depending whether you are using Cut Sheet or Fanfold paper.
The operation of this function is also varied depending upon the Emulation setting (and if in
HP emulation, the PCL mode setting).
46 OVERRIDE BM
TOF Adjustment 0/60 - 480/60 inches
OVERRIDE: NO
OVERRIDE: YES
Top Margin 0/6 - 15/6 inches
•See Table
below for Page
Length B5, B4,
A4, LETTER,
LEGAL, or A3
Printable area
(EPSON/IBM)
Override BM (OFF)
17mm
When using Cut Sheet paper, the bottom
margin is set 17 mm from the bottom of
the page. The bottom margin setting can
be overridden by this function, however,
there may be some degradation of print
registration in the override print area.
Refer to the sketch and Table shown
below for details of printable area and
number of lines/page as affected by the
setting of this function.
TOF Adjustment value
TOF Adjustment value
(PCL3)
Override BM (ON)
0mm
(PCL3+/PCL3+D)
Paper Width
5, 10, or 15 inches
TOF Adjustment
When using Fanfold paper, this function
only affects the printer's operation on the
last sheet of paper when a paper out
condition occurs. When remove the
fanfold paper from the tracters, printing
will stop approximately 4 inches from
the bottom edge of the paper. When a
paper out condition occurs you may
either move the Friction Lever to the Cut
Sheet position and remove the form from
the tractors, or you may place the printer
back Online and continue printing in the
override print area.
0/60 - 480/60 inches
(TOF)
Top Margin
0/6 inch - 15/6 inches
Page Length
2 - 16.5 inches
(default 11")
Printable area
Bottom Margin
0/6 - 15/6 inches
Bottom Margin setting
ends at perforation.
Perforation
TOF Adjustment
0/60 - 480/60 inches
BM=Bottom Margin
Printable area
Override BM
8mm(ON) or 17mm(OFF)
Final form
(EPSON/IBM)
13 mm
13 mm
Override BM(ON)
0mm
Final form
(PCL3+/PCL+D)
Override BM(ON)
-6mm
Final form
(PCL3)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (47-50)
Label mode (valid only in fanfold setting)
Label mode is designed to prevent continuous forms labels from being peeled from the backing
sheet and becoming jammed in the printer.
47 LABEL MODE
........... Set the label protect mode off.
........... Set the label protect mode on.
LABEL MD: NO
LABEL MD: YES
When the bottom edge of the label is positioned on the round surface of the platen for more
than 10 seconds, the label is automatically repositioned away from the platen. When data is
received by the printer, the labels are automatically positioned to the top of the next available
label before printing begins. This function becomes effective when each label is equally apart
and the same page length (min. 2 inches) is set for a single label.
Setting of "Paper out" detection
48 P.OUT DTCT
DETECT: PAGE END
DETECT: ANY POS
In the "ANY POS" setting, "Paper out" detection is functioning at the any position.
In the case of "PAGE END":
For fanfold paper:
"Paper out" detection functions near the perforation only. After
the detection, the print line feed data are not executed. With this
function the printing format is maintained even after the sheet
change.
For cut sheet paper: "Paper out" detection does not function within the paper size.
The "Paper out" detection functions when the LF is exceeded
over the paper size.
When a sheet shorter than the selection sheet size is printed. the
printing is made even if paper out.
Cut sheet feeder type
A function for defining the CSF configuration. The CSF type, single tray can be set when the CSF is
installed.
When single is selected, the paper tray (bin 1) can be selected by the BIN key on the front control panel.
49 CSF OPTION
NOT INSTALL
CSF: SINGLE
CSF: DOUBLE
Setting of the auto-scrolling position
Set the position for executing auto-scrolling.
In the case of "TOF ONLY" : Auto-scrolling is performed only
when the present position is at TOF .
50 SCROLL POS.
"ANY POS" : If the perforation is between the paper cutter and
printing head position, auto-scroll is performed at any position
after a prescribed time after the printing.
SCROLL:ANY POS
SCROLL:TOF ONLY
50
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (51-62)
Line Feed Speed
This function specifies the line feed speed.
The 1/2 LF speed feeds paper more stably. It is useful for thick paper, labeled sheets and
multipart paper in comtinuous printing.
51 LF SPEED
SPEED: NORMAL
SPEED: 1/2
Communication enhancement
Interface type
This function selects the type of interface; the parallel interface or the serial interface. When
this function is executed, the printer is initialized. See "Connecting the computer" section on
page 12 for correct selection and connection of the interface cable.
60 INTERFACE
I/F: PARALLEL
I/F: SERIAL
I/F: AUTO
........... Parallel and serial interface are switched automatically.
SELECT IN signal (parallel interface)
When “SLCT IN: YES” is selected, the printer accepts the “select” or "deselect” command
codes regardless of the SELECT IN signal from host system.
When “SLCT IN: NO” is selected, the printer ignores the “select” or "deselect” command codes
regardless of the SELECT IN signal from host system.
When “SLCT IN: I/F” is selected, the printer functions according to the SELECT IN signal
from host system.
61 SLCT IN CMD
SLCT CMD: YES
SLCT CMD: NO
SLCT CMD: I/F
Parity bit (serial interface)
This function selects the appropriate parity bit in the transmission data frame.
62 PARITY BIT
PARITY: NON
PARITY: EVEN
PARITY: ODD
51
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (63-66)
Data length (serial interface)
This function selects the appropriate data length.
63 DATA LENGTH
LENGTH: 8 BITS
LENGTH: 7 BITS
Stop bit (serial interface)
This function selects the appropriate number of stop bits.
64 STOP BIT
STOP BIT: 1 BIT
STOP BIT: 2 BITS
Communication protocol (serial interface)
This function selects the appropriate communication protocol. Refer to the specification of
your host system for selecting proper communication protocol.
65 PROTOCOL
........... BUSY/READY protocol
........... Set XON/XOFF 1
........... Set XON/XOFF 2
PROT.: DTR
PROT.: XON/OF1
PROT.: XON/OF2
PROT.: ETX/ACK
Note: The difference in XON/XOFF 1 and 2: XON/XOFF 1 protocol sends XON code (11h) to
host system at power-on while XON/XOFF 2 does nothing.
Communication speed (serial interface)
This function selects the appropriate baud rate for the data transmission speed.
66 BAUD RT
SPEED: 38400 B
SPEED: 19200 B
SPEED: 9600 B
SPEED: 4800 B
SPEED: 2400 B
SPEED: 1200 B
SPEED:
SPEED:
600 B
300 B
52
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (67-70)
Serial error check (serial interface)
This function selects the printer's response to a serial data transmission error. The serial data
transmission error includes a parity error, framing error, and over-run error. If "PRINT" is
enabled, the data in error is printed as an asterisk(*). If "IGNORED" is enabled, the data in
error is discarded.
67 SERIAL ERROR
S.ERROR: PRINT
S.ERROR:IGNORED
CTS signal (serial interface)
This function accepts or ignores the CTS (Clear to Send) signal from the host.
68 CTS ENABLE
........... Ignores the CTS signal
CTS: NO
........... Functions according to the CTS signal from the host
CTS: YES
CD signal (serial interface)
This function accepts or ignores the CD (Carrier Detect) signal from the host.
69 CD ENABLE
........... Ignores the CD signal
........... Functions according to the CD signal from the host
CD: NO
CD: YES
DSR signal (serial interface)
This function accepts or ignores the DSR (Data Set Ready) signal from the host.
70 DSR ENABLE
........... Ignores the DSR signal
DSR: NO
........... Functions according to the DSR signal from the host
DSR: YES
53
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (71-74)
Communication buffer size
This function selects the maximum size of the input buffer.
When the selection of this function is completed, the printer is initialized.
The buffer size affects the signal protocol in serial data communication. In these protocols the
printer's busy/ready state changes according to the data remaining values in the input buffer
described below.
Ready to Busy
(CIN)
BUFFER
SIZE
Busy to Ready
(CRN)
71 BUFFER SIZE
64k byte
8k byte
B.SIZE: 64 KB
B.SIZE: 8 KB
B.SIZE: 128 B
1k byte
32 byte
3k byte
64 byte
128 byte
Note: When the remaining data capacity of the input buffer is
smaller than CIN, the printer becomes busy. This state continues
until the remaining capacity of the buffer is larger than CRN.
Busy/ACK timing (parallel interface)
This function selects timing to activate the ACK signal for 8µ seconds (type 1) before, 4µ
seconds (type 2) before, or simultaneously synchronized (type 3) with the busy signal going
low.
Type
Timing
72 BUSY/ACK
BUSY
ACK
8 µs
TYPE 1
TIMING: TYPE 1
TIMING: TYPE 2
TIMING: TIPE 3
BUSY
ACK
TYPE 2
TYPE 3
BUSY
ACK
Data latch timing (parallel interface)
This function selects timing to latch the data signals at the rising edge (type R) or falling edge
(type F) of the STROBE signal.
Type
Timing
73 DATA LATCH
STROBE
TYPE F
DATA 1~8
LTCH: TYPE F.
LTCH: TYPE R.
STROBE
TYPE R
DATA 1~8
Setting of whether ERROR/PE signals are output or not
Setting is made whether or not ERROR and PE signals for the parallel interface are
output.
When "NO" is selected,
ERROR signal remains HIGH, and PE signal remains LOW, even if Error status.
74 ERROR STATUS
STATUS SIG.:YES
STATUS SIG.:NO
54
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (80-82)
Miscellaneous
Print direction
This function selects either pre-directional printing, bi-directional printing, or uni-directional
printing. Software commands to control the printing direction will override this selection.
Particular characters such as IBM graphic characters are always printed unidirectional.
80 PRINT DIR
PRINT: PRE-DIR
PRINT: UNI-DIR
PRINT: BI-DIR
........... Defaults to bi-directional printing
•
Pre-directional printing:
Whenever a double pass of the print head is required, the direction of the second pass is the
same as that of the first pass. This logic-seeking, unidirectional printing can be used,
therefore, in modes such as double strike and double height printing. The logic seeking
capability is executed before the first pass of the print head. The printing direction of all
passes is the same as that of the first pass.
•
•
Bi-directional printing:
Successive passes of the print head alternate between the left-right and right-left direction.
Uni-directional printing:
Data is always printed in a single direction from the left to the right.
LCD display language
This function selects the display language for the printer's display window (LCD).
81 DISPLAY LANG
LANG: ENGLISH
LANG: DEUTSCH
........... English
........... Germany
LANG: FRANCAIS ........... French
LANG: ESPANOL
........... Spanish
LANG: ITALIANO ........... Italian
Invert LCD display
This function sets up-side down text display in the LCD. Use with the reverse control panel
sheet. (See page 136)
82 INVERT DISP
INVERT: NO
INVERT: YES
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Extended setup options (83-87)
Software controlled setup
This function enables/disables the special software commands that are designed to control most
of the extended setup options from host. See "Printer setup command codes" section in
Appendix B.
83 SOFTWARE SET
SOFTWARE: NO
SOFTWARE: YES
Lock the RESET key
This function locks up the RESET key during the online mode in order to avoid an accidental
reset during printing.
84 RESET LOCK
LOCK:
LOCK:
NO
YES
Setting ENERGY STAR
Set the power conservation standby mode.
When this mode is valid, if the standby mode continues about 14 minutes after printing, the
power conservation mode is engaged. Switching to the normal mode is effected when any print
action is performed.
85 SLEEP MODE
SLEEP MODE:YES
SLEEP MODE:NO
Saving user setup options
This function saves the current setup into one of three memory areas.
Press the ENTER key to store the current setup in the desired memory area. This does not
affect the current setting. See "Loading user setup option" for the preprogrammed setups.
86 SAVE SETUP
SAVE: MEMO 1
SAVE: MEMO 2
SAVE: MEMO 3
Printing list of setup options
This function prints the list of the current basic setup options, extended setup options, factory
setup contents, or all the setups in the memory areas.
Press the ENTER key to start the selected item listing. This does not affect the current setting.
87 SETUP LISTING
........... Lists current basic setup options
........... Lists current extended setup options
........... Lists all setup listings including user setups
........... Lists factory setup contents
LIST: MAIN
LIST: EXTEND
LIST: ALL SET
LIST: FACTORY
56
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Setting the application software
6. Setting the application software
About printer driver
Printer Driver is a section of your software that automatically translates instructions from the
software to your printer.
For example, when using some application softwares, if you want to boldface or underline a
word, the printer driver automatically translates your specific boldface or underline instruction
on your application software to printer control command.
Different printers use different control codes for designating print styles. Therefore, it is
important that when you install your software, you select the appropriate printer driver
designed for your printer.
When WINDOWS 3.1, WINDOWS NT 3.51, 4.0, or WINDOWS 95, 98 is used, please install
the Printer Driver attached to this printer.
When this printer is used in the MS-DOS or other environment, such as UNIX or OS/2, proceed
as follows.
Printer driver selection
Select a suitable printer driver from the list of supported printers. This would include either
the Hewlett Packard RuggedWriter 480, Epson LQ-2550 or IBM 2391. Each of these printer
drivers should allow you to access many of the features on your printer.
If this printer is not listed, look for the following printer drivers. While this should allow you
to print your document with your printer, it probably will not allow you to access many features
of the printer. A few of the choices you may see are given below in order of preferences.
Hewlett Packard
RuggedWriter 480
DeskJet 500
Epson
LQ-2500/2550
LQ-1050/1000
IBM
2390/2391
Proprinter XL24E
Proprinter XL24
Notes:
1. Set the emulation type in the extension setup options according to the selection of printer
driver. For example, when you select the Epson LQ-2550 printer driver, you should set the
emulation type to the Epson mode.
2. If the Desk Jet 500 driver, is selected, it is recommended to set up the printer's PCL
MODE(extended setup 38) to PCL3+D.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Setting the application software
Connecting the BX-900 printer in the HP environment
❏ Introduction
The HP emulation of the BX-900 printer provides full compatibility with the HP2235A
RuggedWriter 480 printer.
The BX-900 also provides features and capabilities beyond those ever provided by the HP
RuggedWriter printer. SEIKO Precision Inc. has provided a means for you to access these extra
capabilities for any new applications that you may chose to print on the BX-900.
The extra capabilities of the BX-900 printer are enabled for access through a special control panel
menu setting entitled "38 PCL MODE".
❏ PCL Mode
•
•
PCL3 MODE -Provides the basic RuggedWriter 480 emulation command set.
PCL3+ MODE –Provides extra capability to the RuggedWriter 480 command set that allows you
to access many BX-900 printer features through extensions of the command set.
•
PCL3+D MODE –Provides all features of PCL3+ and allows the vertical and horizontal
positioning to be set in increments of 1/360". This mode provides a "limited" Deskjet capability,
and is mainly intended for printing from Windows using the Deskjet 500 driver. Print output
from this mode will not be identical to that of a Deskjet printer (300 vs. 360 dpi) but will be
closer than the other 2 modes for this type of application.
❏ Setup
The information provided below gives setup information of the basic printer RuggedWriter
emulation, details of the command set extensions provided with PCL3+ and PCL3+D Mode, and
information on configuring the Serial I/O to the various Term Types used by the HP System.
Refer to the setup sections 4 and 5 for details on using the Basic and Extended Setup configuration
modes.
❏ Configuring the Printer with the RuggedWriter Emulation
1. Set the printer menu item 10 EMULATION to "HP".
2. Set the printer menu item 38 PCL MODE to "PCL3".
Setting the PCL MODE to "PCL3" provides the command set identical
with that of the HP RuggedWriter 480.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Setting the application software
❏ Extra Capabilities for new Applications
Listed below is a summary of the expanded command sets available for new applications. Refer to
the Appendix B, page 115 through 121 for details of using the expanded command sets.
PCL3+ Mode
This operation mode provides the following extended capabilities:
Escape
Description
Added Capability:
Bell is now active
Command
BEL
Activates the printer's bell
Controls the print direction
Assign the primary font
ESC & k # W
ESC ( # id
Unidirectional, Bidirectional, Predirectional
PC-850, ISO25, France 2, German2,
Spain 3, Legal, Math7, Math-Symbol,
ISO84 Portugal 2, ISO85 Spain 2
PC-850, ISO25, France 2, German2,
Spain 3, Legal, Math7, Math-Symbol,
ISO84 Portugal 2, ISO85 Spain 2
15, 17.1, 24 cpi
ESC ) # id
Assign the secondary font
ESC ( s # H
ESC ) s # H
Sets the character pitch
Sets the character pitch
(primary)
15, 17.1, 24 cpi
(secondary)
ESC ( s # T
ESC ) s # T
ESC * b # M
ESC * t # R
Sets the primary typeface
Script, Orator, Orator-s, OCR-A, OCR-B
Script, Orator, Orator-s, OCR-A, OCR-B
Off, Mode1, Mode2, Mode3
60, 360 dpi
Sets the secondary typeface
Select graphics data compression
Designates raster graphics resolution
PCL3+D Mode
This mode provides all of the capabilities described above plus the following:
Escape
Description
Added Capability:
Command
ESC * p # X
ESC * p # Y
Sets horizontal positioning by dot
Sets vertical positioning by dot
1/360"
1/360"
Saving Your Setup
Once you have completed your printer set-up, the configuration can be saved as a User setup.
Use the printer's Extended Setup menu 86 SAVE SETUP and save your setting as either MEMO 1,
MEMO 2, or MEMO 3.
This saved setup may be re-initialized at any time using 8 SELECT SETUP to select the applicable
User setup MEMO 1, MEMO 2, or MEMO 3.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Troubleshooting
7. Troubleshooting
If an error occurs during printing, you will get several warnings. A buzzer sounds, P.OUT
lamp blinks, and an error message appears in the display window of the front control panel.
❏ Error Messages
Error Message
Cause and Solution
The printer cannot detect the print head position.
CARRIAGE ERROR
❏
Turn off the printer immediately. After a brief wait, turn on
the printer again.
Internal RAM does not function properly.
RAM ERROR
(NO LCD DISPLAY
The P.OUT lamp blinks and the
buzzer sounds after power on. )
❏
Turn the printer off and back on again. If the error persists,
consult your dealer.
Abnormal fan operation is detected.
FAN ERROR
Long continuous printing may overheat the print head.
HEAD PROTECTION
❏
The printer stops temporarily and restarts automatically
when the print head temperature lowers to a safe level.
(ON LINE lamp blinks.)
Paper jam or improper paper operation has occurred.
PAPER ERROR
❏
If paper parking is not completed, press the PARK key.
(Buzzer sounds 3 times.)
Otherwise reload the paper.
Paper is not loaded in the printer.
Load paper (pages 13 and 14).
PAPER OUT
❏
One of the printer covers is open.
Close the cover to restart the operation.
COVER OPEN
POWER DOWN
❏
Abnormal current is detected.
❏
The printer is automatically turn off. Stop using the printer,
and contact the dealer.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Troubleshooting
❏ Troubleshooting guide
Problem
Cause and Solution
❏
❏
Power cord not connected.
Blown fuse in the printer.
POWER lamp fails to light
❏
Print head has overheated. Wait until it has cooled down.
Printer stops or slows
down on printing
❏
❏
Paper detect sensor may be damaged.
Sensor hole is clogged.
P.OUT lamp lights
incorrectly
❏
❏
❏
Old or worn out ink ribbon needs to be replaced.
Head adjustment lever is not set correctly.
Head may need to be cleaned or replaced.
Poor quality printing or
smudging of the paper
❏
❏
Ribbon cassette is not properly installed.
Some characters miss
printing
Host system control and data code may not match the
printer's setup.
Incorrect character
printed
❏
❏
❏
❏
Incorrect paper select lever setting.
Paper not advancing
Fanfold paper slips
Stack of fanfold paper behind the printer is placed
crookedly.
The paper select lever is in the single sheet setting.
The automatic carriage return option in the extended setup
options is set incorrectly.
Extra line feed
Paper jam
❏
❏
Paper is curled.
Move the paper select lever to the continuous paper setting
and carefully remove the jammed paper.
❏
Turn off the printer and wait one minute, and then turn it
back on again. Consult your dealer if the error persists.
Paper bail abnormal
operation
61
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Troubleshooting
❏ Input hexadecimal dump mode
The Input hexadecimal dump capability of the printer enables monitoring of data as it is sent to
the printer. Each Escape Sequence, Control Code, and ASCII character sent from the computer
to the printer is printed in a two-digit hexadecimal format. Such printing is initiated after 16
bytes of data have been transmitted to the printer. Hexadecimal values and their corresponding
ASCII characters between the values 20h to 7Eh are printed on each line.
HEX DUMP LQ
To run this mode in draft printing
Press the FF key while turning ON the printer or pressing the RESET key. Hold down the FF
key until the LCD displays "HEX DUMP DRAFT"
To run this mode in LQ printing
Press the FF and ON LINE keys simultaneously while turning ON the printer or pressing the
RESET key. Hold down the both FF and ON LINE keys until the LCD displays "HEX DUMP
LQ"
To terminate this mode
Press the RESET key or turn off the power.
Example
10 REM HEXADECIMAL DUMP LIST EXAMPLE
20 OPEN "LPT1:"AS #1
30 WIDTH #1,255
40 PRINT #1,"ABC";CHR$(13);CHR$(10);
50 PRINT #1,"123";CHR$(13);CHR$(10);
60 PRINT #1,"HENRY IS HANDSOME"
70 END
00000 41 42 43 0D 0A 31 32 33 0D 0A 48 45 4E 52 59 20 ABC..123..HENRY
00010 49 53 20 48 41 4E 44 53 4F 4D 45 0D
IS HANDSOME.
ASCII characters are printed according to hexadecimal codes of the data. Codes other than
1Bh and 20h to 7Eh are printed as “.” (2Eh). For the code 1Bh, “IE” is printed in draft mode
and “ESC” is printed in LQ mode.
During the hexadecimal mode, the SETUP, and QUALITY keys are disabled.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
8. Maintenance
❏ Cleaning
Minimum periodical cleaning will ensure the maximum performance from your printer. Do not
spill or splash cleaning liquid inside the printer. Please refer to the "Printer cover removal" on
page 64 to remove the covers for cleaning.
Before cleaning the printer, be sure to turn off the power and disconnect the power cord.
Power may be required to clean the platen.
Platen
❏
Use a platen cleaner, or any weak alcohol solvents, to remove any
ink from the platen and bail rollers. Do not apply any other liquid
chemical to the platen.
Even with a specified platen cleaner, frequent use of the liquid
is not recommended. Apply only when it is necessary.
❏
❏
Use a vacuum cleaner to remove paper dust and particles inside the
printer. A small brush is suitable for removing paper dust from
hard-to-get-at areas.
Inside the printer
Exterior Casings
Clean with a soft cloth dampened with a mild detergent. Never
use organic solvents such as alcohol or thinner.
FPC cable plastic binder
Make sure that the binder clamps the cable securely.
Exterior Casings
Inside the printer
Clean with a soft cloth dampened
with a mild detergent.
Thoroughly vacuum these areas.
Remove any collected paper dust and particles.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance (Lubrication)
❏ Lubrication
In the case of heavy use of the printer, apply a specified lubricating oil only to the front and
rear metal carriage bar. When applying the lubricant to the carriage bars, spread the oil by
manually moving the print head back and forth along the carriage bar.
Consult your dealer to obtain the recommended lubricating oil. Do not use an unspecified oil,
or it may reduce the printer's performance drastically.
Oiling
Clean thorougly with a dry cloth,
then apply specific type of lubricants:
Cosmo Hydro (HV#22) recommended.
Ref. P/N 298269-001
Rear bar
Front bar
❏ Printer cover removal
Rear Top Cover Removal
❏
❏
Remove the Rear Cover.
Open the Rear Cover to the level
position and pull it.
Remove the two stoppers for the Rear
Top Cover.
Detach the two screws to remove the
two Stoppers.
Remove the Rear Top Cover.
Slide the Rear Top Cover toward the
rear and raise it to vertical position and
lift straight upward.
Stopper
Stopper
❏
64
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance (Printer cover removal)
Printer Cover
Guide
❏
Open the front cover to an upright
position, then lift and remove the
cover.
Pivot
Rear Cover
Open the rear cover from the
❏
bottom edge of the cover and pull it
away from the printer to remove.
Paper Rack
Slide both paper guides to the
❏
extreme left and right edges of the
paper rack. Raise the rear end to
stand vertically and lift straight
upward to remove.
Sound Seal Cover
Push out on the outer edge of the
❏
sound seal cover where it connects
to the L-angle from the printer
while pushing the stud of the L-
angle out of the hole. Then remove
the whole cover.
L-angle Hinge
65
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance (Vertical alignment mode)
❏ Vertical alignment mode
The vertical alignment mode serves to compensate for the slippage of the vertical printing
positions, that occurs due to individual differences and age distortion of the printer.
This mode has two features: print start alignment as A-MODE and bidirectional print alignment
as B-MODE. The print start adjustment aligns the print position of two different print modes at
the left margin. While the bidirectional print adjustment aligns the vertical dot mis-positioning
within one print mode in bidirectional printing. Because of their correlation, always set the
bidirectional alignment after the print start adjustment.
The print mode used for these adjustments is categorized as 11 and 12 groups (A-MODE 1 to
11, B-MODE 0 to 11) that differ in printing speed. By aligning characters with the typical
character mode of each group, the character modes within the group are automatically adjusted,
e.g. Draft pica printing mode belongs to MODE 0 group.
Operation and printing pattern
Before performing the adjustment mode, make sure that the ribbon cassette and at least 10-inch
wide paper are properly installed in the printer.
Select mode No.
Select pattern No.
Exit alignment mode
TOF SET
POWER
ON LINE
P.OUT
PARK
BIN
QUALITY
M.LF
LF
FF
ALIGN ADJUST
EXIT
ENTER
ALT
SETUP
M.RLF
RLF
TEAR OFF
ON LINE
RESET
Enter alignment mode
Set printing conditions
1 Press the SETUP and ALT keys simultaneously while turning ON the printer or pressing the
RESET key. Hold down the both SETUP and ALT keys until the LCD displays "ALIGN
ADJUST".
SETUP + ALT + RESET or Power ON
key
ALIGN. ADJUST
MENU indication
A: START POS ADJ
B:
VERT. ADJ
2 Press the left or right arrow key to select A-MODE for print start adjustment or B-MODE for
bidirectional print adjustment. Then press the ENTER key to enter. The operation on either
alignments is done in the same manner. Always select B-MODE after A-MODE is set or has
been set correctly.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance (Vertical alignment mode)
3 13 patterns from 0 to 12 are printed in accordance with the printing conditions. The pattern of
the present printing condition is indicated with asterisks (*).
PRINTED PATTERNS EXAMPLE
Description of Patterns
•
•
A pattern describes the type of printing conditions for each mode.
A number with “*” in the printing example represents the printing condition
being set at present.
•
The dots pattern (" " ") indicates the printing condition in between the adjacent
patterns, the setting is valid.
" " "
4 Make sure, the vertical alignment of the chosen print pattern which is marked with "*" is the
best aligned among the 0-12 patterns.
If not the best, you may change to the best aligned one among 0-12.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance (Vertical alignment mode)
A-MODE 1: NO. 6
LCD Description
Key Operation
Pattern No. (0-12)
Mode No. (1-11or 0-11)
Up and down arrow keys
Left and right arrow keys
EXAMPLE (To change the pattern No. 6 to 7 in A-MODE 4.)
A-MODE 3
0
1
2
3
4
5
6
7
8
9
10
11
12
*
>---->
HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH
>----> HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH
Best aligned is chosen
A-MODE 4
0
1
2
3
4
5
6
7
8
9
10
11
12
*
>---->
>---->
HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH
HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH HHH
Best aligned
Bad aligned is chosen
5 Pressing the Left and Right arrow key changes the Mode number
between 1 to 11 to select the best pattern within the mode.
A-MODE 3: NO.6
QUALITY
PARK
A-MODE 4: NO.6
6 Pressing the Up and Down arrow key changes the pattern number
between 0 to 12 to select the best pattern within the mode.
A-MODE 4: NO.6
M.LF
M.RLF
A-MODE 4: NO.7
7 By scrolling to the desired pattern number and pressing the ENTER key, the selected printing
condition is set. When the condition is set, the corrected pattern of the selected print mode is
printed out.
8 Repeat the steps 5 through 7 until the start position adjustment is completed.
9 Pressing the EXIT key to exit from the start position adjustment (A-MODE). The bidirectional
printing adjustment (B-MODE) takes place automatically and the LCD indicates "B: VERT
ADJ".
10 Press the ENTER key to enter the bidirectional printing adjustment (B-MODE).
11 Repeat the steps 5 through 7 until the bidirectional printing adjustment is completed.
12 After all adjustments are completed, press the EXIT key, then the LCD indicates "PRESS
RESET SW". By pressing the RESET key, the printer exits from this vertical alignment mode.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
9. Bar code and enlarged character
Bar code function
The printer can print bar codes and enlarged characters.
To activate the bar code and enlarged character function, set #27 BARCODE/ENLARGED CHAR to
MODE 1 or MODE 2 in the EXTENDED SETUP MODE.
This function is applicable to the EPSON or IBM or HP mode. This section describes the outline and
details of the bar code and enlarged character function.
Outline of bar code function
The printer has 14 types of bar codes.
Software commands and options #27 to #29 on the EXTENDED SETUP MODE are used to print bar
codes and enlarged characters.
The software commands are unique to the printer. See the following pages for details of these commands.
1. Industrial 2 of 5
2. Interleaved 2 of 5
3. Matrix 2 of 5
4. Codabar
8. Code 128
9. EAN-8
10. EAN-13
11. UPC-A
5. Code 11
12. UPC-E
6. Code 39
13. Postnet
7. Code 93
14. Element (Created in elements.)
❏ Makeup of bar code
(Example) CODABAR
ICG
ICG
Check
STOP
START
Character
Character
Character
DATA
HRI
Margin
Barcode
Margin
Start Character : Initial character of data
DATA : Alphanumeric data
Check Character : Character for check errors in read data
Stop Character : Last character of data
HRI : Human Readable Interpretation
ICG : Gap between characters (Inter Character Gap)
Margin : Data-free portions must be provided on both sides.
Each data-free portion must be approximately ten
times as wide as the narrow space (NS).
69
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Specified items on Bar Code
(Example) CODABAR
Inter Character Gap
START
Character
STOP
Character
Wide Space
Narrow Space
Wide Bar
Narrow Bar
Check Character
HRI
Bar Code command
Function
Command
DC4 DC4 T
DC4 DC4 E
DC4 DC4 H
DC4 DC4 I
DC4 DC4 F
DC4 DC4 C
ESC SI
1.
Bar code type
2.
3.
Element width
Bar code height
Setting HRI on and off
HRI font
4.
5.
6.
Check character
7.
Starting the bar code data sequence
Ending the bar code data seqence
Bar code data sequence
8.
ESC SO
9.
DC4 DC4 B
DC4 DC4 D
DC4 DC4 G
DC4 DC4 N
DC4 DC4 R
DC4 DC4 S
DC4 DC4 V
DC4 DC4 @
10.
11.
12.
13.
14.
15.
Printing density
Guard bar expansion
Start and stop characters
Bar code rotational angle
Disabling HRI of the start and stop characters
Value input mode
16.
Initializing the bar code mode
(1)
Bar code type: DC4 DC4 T
Format: ASCII
DC4
14
20
DC4
14
20
T
54
84
n
n
n
Hex
Decimal
Function: Specifies the bar code type
n =0 Industrial 2 of 5
1 Interleaved 2 of 5
2 Matrix 2 of 5
3 Codabar
7 Code128
8 EAN-8
9 EAN-13
10 UPC-A
4 Code11
11 UPC-E
5 Code39
12 Postnet
6 Code93
255 Element Print
Parameter 255 (Element print) is used to print a bar code which is input element by element. It can print a bar
code which is not supported by the printer and is represented by combining elements. Since data is input by
elements, HRI printing is not performed and no check digit is added to the bar code. The start and stop
characters is also not added.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(2) Element width: DC4 DC4 E
Format: ASCII DC4 DC4
E
n1 n2
Hex
Decimal
14
20
14 45 n1 n2
20 69 n1 n2
Function: Specifies the n2/120” or n2/180” width of the element n1.
1 ≤ n2 ≤ 127)
120” or 180” is specified with the DC4 DC4 D command.
(
n1 = 0: Narrow bar
3: Wide space
1: Wide bar
4: Inter-character gap
2: Narrow space
The narrow bar width or narrow space is used as the element width for
Code 93, Code 128, EAN-8, EAN-13, UPC-A, and UPC-E.
One element width of bar 1: Narrow bar width
One element width of space 1: Narrow space width
The midium bar or wide space width is used as the midium element
width for Code 11. The wide element width is (wide bar width x 2 -
narrow bar width).
This setting is not valid for Postnet.
The inter-character gap means the space between each set of codes of a
bar code which begins with a bar and ends with a bar.
(3) Bar code height: DC4 DC4 H
Format: ASCII
Hex
DC4
14
20
DC4
14
20
H
48
72
n
n
n
Decimal
Function: Sets the bar code height to n/12”. (0 ≤ n ≤ 120)
The currently set line feed pitch serves as the bar code height when
is set to 0. This setting is not valid for Postnet.
(4) Setting HRI on and off: DC4 DC4 I
Format: ASCII
DC4
14
20
DC4
14
20
I
49
73
n
n
n
Hex
Decimal
Function: Specifies whether or not to print an HRI. Also specifies the
HRI printing position if an HRI is to be printed.
n = 0: HRI not printed.
1: HRI printed below the bar code symbol.
2: HRI printed above the bar code symbol.
No HRI printed for Postnet or Element regardless of this setting.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(5) HRI font: DC4 DC4 F
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
F
46
70
n
n
n
Function: Selects the font of printing the HRI.
n = 0: Currently selected font
1: OCR-A
2: OCR-B
This setting is not valid for Postnet or Element.
(6) Check character: DC4 DC4 C
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
C
43
67
n
n
n
Function: Specifies whether to add a check character automatically.
n = 0: No check character is added. (If a check character is needed, the
user must send bar code data.)
1: A check character is added. (The check character is not printed
in the HRI when Code 93 or Code 128 is selected.)
If the Codabar or Element is selected, no check character is added regardless of
this setting.
The following shows the methods of determining the check characters and bar code
types. (For details, see “Calculating the check character” below.)
Modulus 10 Industrial 2 of 5, Interleaved 2 of 5, Matrix 2 of 5, EAN, UPC,
Postnet
Modulus 11 Code 11 (Dual Check character)
Modulus 16 Codabar
Modulus 43 Code 39
Modulus 47 Code 93 (Dual Check character)
Modulus 103 Code 128
(7) Starting the bar code data sequence: ESC SI
Format: ASCII
ESC
1B
27
SI
0F
15
Hex
Decimal
Function: Indicates the starting the bar code data sequence.
Data between this and the end command of the bar code data sequence
is regarded as bar code data.
This command is valid only when #27 BARCODE/LABEL MODE is
set to MODE 2 in the EXTENDED SETUP MODE.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(8) Ending the bar code data sequence:
Format:
ESC SO
ASCII
Hex
ESC
1B
SO
0E
14
Decimal
27
Function: Indicates the ending the bar code data sequence.
This command is valid only when #27 BARCODE/LABEL MODE is set
to MODE 2 in the EXTENDED SETUP MODE.
(9) Bar code data sequence: DC4 DC4 B
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
B
42
66
n
n
n
d1
d2 ... dk
Function: Specifies the number (“n”) of data to be regarded as bar code data.
00 ≤ ≤ 68
00 ≤ dk ≤ 255
00 ≤ ≤ 68
n
k
If the Element is selected; 0
≤
n, dk, k ≤ 255
This comand is valid when #27 BARCODE/LABEL MODE is set to MODE1 or
MODE2 in the EXTENDED SETUP MODE.
(10) Printing density: DC4 DC4 D
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
D
44
68
n
n
n
Function: Specifies the density of printing bar code symbols (in the horizontal
direction).
Specifies the unit of element width.
n = 0:
1:
Bar code symbols are printed at 120 dpi. (Default value)
Bar code symbols are printed at 180 dpi.
If a bar code is rotated by 90 or 270 degrees using the DC4 DC4 R (bar code
rotational angle) command, a bar code is printed at 120 dpi horizontally and 180
dpi vertically.
(11) Guard bar expansion: DC4 DC4 G
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
G
47
71
n
n
n
Function: Specifies whether or not to expand EAN or UPC guard bars.
n = 0: Guard bars are not expanded.
1: Guard bars are expanded. (Default value)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(12) Start and stop characters: DC4 DC4 N
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
N
4E
78
n1
n1
n1
n2
n2
n2
Function: Specifies the Codabar start or stop character. n1 selects the
start or stop character. n2 specifies a code of the start or stop
as shown below.
n1 = 0: Start character
1: Stop character
✽
n2 = a, b, c, d, t, n, , or e.
When power is turned on, “a” is selected as the start or stop character.
(13) Bar code rotational angle: DC4 DC4 R
Format:
ASCII
Hex
DC4
14
20
DC4
14
20
R
52
82
n
n
n
Decimal
Function: Specifies the rotational angle of the bar code in units of 90 degrees.
n = 0: 0° (Default value)
1: 90°
2: 180°
3: 270°
(14) Disabling HRI of the start and stop characters: DC4 DC4 S
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
S
53
83
n
n
n
Function: Specifies whether or not to print the start or stop character in the
for Codabar, Code 11, Code 39 or Code 93.
n = 0: The start or stop character is printed in the HRI.
(Default value)
1: The start or stop character is not printed in the HRI.
(15) Value input mode: DC4 DC4 V
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
V
56
86
n
n
n
Function: Specifies whether bar code sequence data is regarded as the normal
character code or a character value when Code 128 is selected.
n = 0: Data is regarded as normal character code. (Default value)
1: Data is regarded as a character value.
If data is regarded as the normal character code, the printer
automatically move the subset or inserts a shift code according to
the data.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(16) Initializing the bar code mode: DC4 DC4 @
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
@
40
64
Function: Initializes the bar code mode.
The following show the default settings for bar code.
Bar code type:
SETUP
Narrow bar width:
Wide bar width:
Narrow space width:
Wide space width:
Inter- character gap:
Bar code height:
Setting HRI:
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
Below the bar code symbol
OCR-B
HRI font
Check character:
Printing density:
Added
1/120”
Data processing in the bar code data sequence
✽ In a bar code data sequence following ESC SI, any codes
other than the ESC code are regarded as bar code data.
Continuous two-byte ESC codes (ESC + ESC) are
regarded as a one-byte ESC bar code.
✽
In a barcode data sequence following ESC SI, SO ESC+
SI and ESC + ESC are valid and the other ESC sequence
are ingnored. The ESC code and the following data, two
bytes in all, are discarded.
✽
When a start or stop character code (e.g., ‘*’ code of
Code 39) is input in a bar code data sequence, the bar
code data sequence stops if bar code data has already
been input in that sequence. The data that was input is
valid (and converted into a bar code). If not, the bar code
data sequence does not stop and the code is discarded.
✽
When 68 bytes of data is input, the bar code data
sequence ends automatically.
When Code 93 or Code 128 is selected, the bar code data
sequence ends when the amount of input data, including the
automatically inserted control character, reaches 68
75
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Printing bar codes
✽
Bar codes are printed at 236 cps print speed when the printing density is 120 dpi or at 158 cps
print speed when the printing density is 180 dpi. (This does not apply to printing paths involving
HRI printing or duty control.)
✽
Bar codes and normal characters are printed separately. When the bar code data
sequence start code is processed, print data other than bar code data contained in the
buffer is printed. When print data other than bar code data is input, bar code data
contained in the buffer is printed.
✽
Like the right margin overflow processing for character data, data preceding bar code
data is printed and the bar code data is printed from the left margin on the following line
if the data exceeds the right margin.
If bar code data cannot be printed between the left and right margins, the bar code data
is ignored.
✽
✽
If the vertical line feed pitch is smaller than the bar code height, reverse feeding is
performed to move to the following printing position. (If an out-of-paper error is detected
in a bar code printing path, the following paths are printed on the following form.)
HRI
The HRI is adjusted to the center of the bar code symbol width and printed at 10 cpi
unless EAN or UPC guard bar expansion is executed. If EAN or UPC guard bar
expansion is executed, an HRI is printed at the equal space between the center guard bar
and the left or right guard bar.
If the HRI width is greater than the bar code symbol width, the HRI printing pitch is
reduced to print the HRI in the same width as the bar code symbol width.
✽
The HRI is printed below a bar code symbol, the vertical printing position is lower than
the printing start position by (bar code height - 1/6”). If it is printed above the bar code
symbol, the vertical printing position is higher than the printing start position by (1/6” -
24/180”).
✽
✽
When Code 11 is selected, small triangle ( ) and large triangle ( ) are printed as the
start and stop characters, respectively. (This does not depend on the setting of the check
character.)
When Code 93 is selected, white squares ( ) are printed as the start and stop characters,
and a black square ( ) is printed as the control character. A printable character
expressed in combination with the control character is printed as is. (For example, 61H is
printed as ‘a’, not ‘ A’.)
✽
When Code 128 is selected, black rhombuses a (✽) are printed instead of non-printable
76
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Error processing
✽
If a character code that is not valid for the selected bar code type is input, the character
code is not converted into a bar code symbol but is printed as a character. If the bar code
has a start or stop character added to the HRI, the start or stop character is printed.
‘
’ is printed instead of an invalid character.
✽
✽
If an incorrect number of data are input to form a bar code which should have a specific
number of data, are input data is not converted into a bar code symbol but is printed as
is.
If incorrect data is input in the UPC-A format and cannot be converted into the UPC-E
format, the input data is not converted into a bar code symbol but is printed as is. (For
the rules of converting the UPC-A format into the UPC-E format, see “UPC-E
conversion rule” below.)
Code 128 subset transition rule
✽
The following shows the transition conditions from subset A to subset B.
1. Input a character code unique to subset B (60H to 7FH) when subset A is
selected.
2. Then input a character code unique to subset B (60H to 7FH) without inputting
a character code unique to subset A (00H to 1FH). (If a character code unique
to subset A is input in this step, subset B is not selected. The character code
unique to subset B input in step 1 is expressed with the shift code.)
✽
The following shows the transition conditions from subset B to subset A.
1. Input a character code unique to subset A when subset B is selected.
2. Then input a character code unique to subset A without inputting a character
code unique to subset B. (If a character code unique to subset B is input in this
step, subset A is not selected. The character code unique to subset A input in
step 1 is expressed with the shift code.)
✽
✽
Subset C is selected when four continuous character codes (30H to 39H) are input.
If a code common to subset A and subset B is input when a subset is not determined or
subset C is selected, subset B is selected temporarily selected.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
UPC-E conversion rule
G
NSC, manufacturer’s codes (M1 M2 M3 M4 M5), and product item codes (X1 X2 X3 X4
X5) are input data.
1. NSC must be 0 or 1.
2. When the manufacturer’s code data is input, the rule is determined and zero
checking of the product item codes is performed.
✽
NZ: Non-zero
UCP-A Type
: 0 to 9
M1 M2 M3 M4 M5 X1 X2 X3 X4 X5
Rule 1
Rule 2
Rule 3
Rule 4
✽
✽
✽
✽
✽
✽
✽
✽
✽
✽
NZ
0
NZ
0
0
0
0
0
0
0
0
0
0
0
0
0
0
✽
0
0
✽
✽
5~9
✽
✽
3~9
0~2
✽
0
✽
3. The following table shows print data if the rule shown above is met.
UCP-E Type
Rule 1
M1 M2 M3 M4 M5 X5 (5~9)
Rule 2
Rule 3
Rule 4
M1 M2 M3 M4 X5
M1 M2 M3 X4 X5
M1 M2 X3 X4 X5 M3 (0~2)
'4'
'3'
Calculating the check character
• Modulus 10
a. The data at the odd-numbered position counted from the right are weighed as 3. The sum of the data
character values is determined.. (The sum is determined without weighing for Postnet.)
b. The remainder of deviding the value determined in step a by 10 is determined.
c. A character having a character value equal to the remainder of subtracting the value determined in
step b from 10 is the check character.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
• Modulus 11
a. Data characters are weighed from the right to the left, as, example,1, 2, ..., 10, 1, 2 ... 10, 1,
2 and so forth. The sum of the data character values is determined. (The symbol ‘-’ has a
character value of 10.)
b. A character having a character value equal to the remainder of dividing the value
determined in step a by 11 is the first check character (C).
c. Data characters are weighed from the right to the left, beginning with C, as, for example, 1,
2, ..., 9, 1, 2 ... , 9, 1, 2 and so forth. The sum of the data character values is determined.
d. The character with a character value equal to the remainder of dividing the value determined
in step c by 11 is the second check character (K).
• Modulus 16
a. The sum of the all characters including start and stop characters values is determined. The
following table shows the conversion of character into value.
Value Character Value Character Value Character Value Character
0
4
8
12
16
0
4
8
:
1
5
9
13
17
1
5
9
/
2
6
10
14
18
2
6
-
.
C
3
7
11
15
19
3
7
$
+
D
A
B
b. The remainder X of deviding the value determined in step a by 16 is determined. The
remainder Y of subtracting the remainder X from 16 is determined.
c. Convert the remainder Y into the character Z according to the conversion table in a. The
character Z is the check character.
• Modulus 43
a. The sum of the data character values is determined.
b. The character with a character value equal to the remainder of dividing the value
determined in step a by 43 is the check character.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
• Modulus 47
a. Data characters are weighed from the right to the left, as, for example, 1, 2, ..., 20, 1, 2 ...
20, 1, 2 and so forth. The sum of the data character values determined..
b. The character with a character value equal to the remainder of dividing the value determined
in step a by 47 is the first check character (C).
c. Data characters are weighed from the right to the left, beginning with C, as, for example, 1,
2, ..., 15, 1, 2 ... , 15, 1, 2 and so forth. The sum of the data character values is determined.
d. The character with a character value equal to the remainder of dividing the value found in
step c by 47 is the second check character (K).
• Modulus 103
a. The sum of the products of the data character values and position values is determined. (The
leftmost character has a position value of 1.)
b. The start character value is added to the sum determined in step a above.
c. The character with a character value equal to the remainder of dividing the value
determined in step c by 103 is the check character.
Other
G
G
After executing a BS command input immediately after bar code data, printing starts from
the position by one character to the left of the currently set character pitch.
When a margin is specified, bar code data in the buffer is cleared.
Element printing
G
G
The element printing function prints bar codes by inputting data element by element.
This function allows the user to print bar codes which are not supported by the printer but
are expressed by combining elements. No HRI is printed, no check digit is added, and a
start or stop character is not added, since data is input element by element.
G
The following show the codes expressing elements.
00H:
01H:
02H:
03H:
04H:
Narrow bar
Wide bar
Narrow space
Wide space
Inter-character gap
80
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Element printing example
[Example]
The following shows a BASIC program for printing Code 39 bar codes using the element printing
function. This example shows how to print “CODE39”. (Replace NB, WB, NS and WS in the data
statements in the following example with 0, 1, 2 and 3, respectively.)
100 OPEN "LPT1:" AS #1: WIDTH #1,255
110 DC4$=CHR$ (&H14): ESC$=CHR$(&H1B)
120 SI$=CHR$(&HF):SO$=CHR$(&HE): ICG=4
130 '
140 PRINT #1, DC4$;DC4$;"@";
' Initialize
150 PRINT #1, DC4$;DC4$;"T";CHR$(255); ' Barcode Type: Element Print
160 PRINT #1, DC4$;DC4$;"E";CHR$(0);CHR$(2); ' Narrow Bar: 2/120"
170 PRINT #1, DC4$;DC4$;"E";CHR$(1);CHR$(6); ' Wide Bar: 6/120"
180 PRINT #1, DC4$;DC4$;"E";CHR$(2);CHR$(2); ' Narrow Space: 2/120"
190 PRINT #1, DC4$;DC4$;"E";CHR$(3);CHR$(6); ' Wide Space: 6/120"
200 PRINT #1, DC4$;DC4$;"E";CHR$(4);CHR$(2); ' Inter Char Gap: 2/120"
210 PRINT #1, DC4$;DC4$;"H";CHR$(6);
220 '
' Barcode Height: 6/12"
230 PRINT #1, DC4$;DC4$;"B";CHR$(9*8+7); ' Barcode Data Sequence Start
240 RESTORE 440
250 FOR I=1 TO 9:READ A:PRINT CHR$(A);:NEXT I
260 PRINT #1, CHR$(ICG);
270 FOR J=1 TO 6
280 IF J=1 THEN RESTORE 450
290 IF J=2 THEN RESTORE 460
300 IF J=3 THEN RESTORE 470
310 IF J=4 THEN RESTORE 480
320 IF J=5 THEN RESTORE 490
330 IF J=6 THEN RESTORE 500
340 FOR I=1 TO 9:READ A: PRINT #1, CHR$(A);:NEXT I
350 PRINT #1, CHR$(ICG);
360 NEXT J
370 RESTORE 440
380 FOR I=1 TO 9:READ A: PRINT #1, CHR$(A);:NEXT I
400 PRINT #1,CHR$(13);CHR$(10);
410 CLOSE #1
' CR+LF
420 END
430 '
440 DATA 0, 3, 0, 2, 1, 2, 1, 2, 0
450 DATA 1, 2, 1, 2, 0, 3, 0, 2, 0
460 DATA 1, 2, 0, 2, 1, 2, 0, 3, 0
470 DATA 0, 2, 0, 2, 1, 3, 0, 2, 1
480 DATA 1, 2, 0, 2, 1, 3, 0, 2, 0
490 DATA 1, 2, 1, 3, 0, 2, 0, 2, 0
500 DATA 0, 2, 1, 3, 0, 2, 1 ,2, 0
81
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Enlarged character function
If #27 BARCODE/ENLARGED CHAR is set to MODE 1 or MODE 2 in the EXTENDED SETUP MODE,
enlarged characters can be printed. The enlarged character function is valid for the EPSON or IBM or HP
mode.
Outline of enlarged character function
When the enlarged character mode is selected with the DC4 DC4 l 1 command, any
commands other than those shown below are ignored.
Only three print codes are available: LF, CR and FF. If 521 or more characters of data are
sent without inputting a print command, printing is performed automatically.
Enlarged character command list
Function
Executing backspacing
Command
BS
1.
2.
Executing line feeding
LF
3.
Executing form feeding
FF
4.
Executing carriage return
CR
5.
Initializing the enlarged character mode
Arrangement of enlarged characters
Cell expansion for enlarged characters
All-character set for enlarged characters
Selecting an enlarged character font
Height expansion for enlarged characters
HMI for enlarged characters
DC4 DC4 @
DC4 DC4 a
DC4 DC4 c
DC4 DC4 d
DC4 DC4 f
DC4 DC4 h
DC4 DC4 i
DC4 DC4 j
DC4 DC4 l
DC4 DC4 o
DC4 DC4 p
DC4 DC4 q
DC4 DC4 r
DC4 DC4 s
DC4 DC4 t
DC4 DC4 u
DC4 DC4 w
DC4 DC4 x
DC4 DC4 y
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
VMI for enlarged characters
Setting and canceling the enlarged character mode
Enlarged character cell offset
Enlarged character pitch
Enlarged character quality
Enlarged character rotational angle
Setting and canceling enlarged character smoothing
Enlarged character top offset
Setting and canceling underline for enlarged characters
Enlarged character width expansion
Horizontal printing position for enlarged characters
Vertical printing position for enlarged characters
82
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(1) Executing backspacing: BS
Format:
ASCII
Hex
Decimal
BS
08
08
Function: Executes backspacing.
When the BS command is executed, the printing position moves to the
previous character position on the left. The BS command is valid up to
the left margin. A BS command issued on the left margin is ignored.
When a BS command is issued when there is a character on the left with
proportional printing selected, the printer backspaces to that character. If
there is no character or another BS command has just been executed, the
printer backspaces by one space.
(2) Executing line feeding: LF
Format:
ASCII
Hex
Decimal
LF
0A
10
Function: Executes line feeding.
After printing data, the printer feeds one line by the enlarged character
line feed pitch, which differs depending on whether VMI is valid (by the
DC4 DC4 j command) or not.
VMI valid: Preset VMI amount
VMI not valid: (24 + cell offset)/180” x cell expansion
Line feeding involves a carriage return if the LF SETTING option is set
to LF + CR in the EXTENDED SETUP MODE.
If the bottom margin is specified and the cell size (i.e., 24/180” x cell
expansion) is greater than the printable area in the CSF, cut sheet, or
fanfold paper mode, form feeding is executed and then printing is
executed. If the printing position is at the TOF position, printing is
executed up to the bottom margin without executing form feeding, and
excess data is not printed.
The default pitch is “1/6” x cell expansion”.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(3) Executing form feeding: FF
Format:
ASCII
Hex
Decimal
FF
0C
12
Function:
Executes form feeding.
This command feeds the page to the next TOF position. If there are still enlarged
characters to be printed, they are printed, then form feeding is executed.
(4) Executing carriage return: CR
Format:
ASCII
Hex
Decimal
CR
0D
13
Function:
Executes carriage return.
This command moves the printing position to the left margin without printing any
characters. If the CR SETTING option is set to CR + LF in the EXTENDED
SETUP MODE, a carriage return is executed out after printing.
(5) Initializing the enlarged character mode: DC4 DC4 @
Format: ASCII DC4
DC4
14
20
@
40
64
Hex
14
20
Decimal
Function:
Initializes the enlarged character mode.
The following show the default settings for enlarged characters:
Cell expansion:
Height expansion:
Width expansion:
Font:
SETUP expansion
SETUP expansion
SETUP expansion
SETUP font
Character pitch:
HMI:
10 cpi
Invalid
Cell offset:
6/180”
VMI:
Invalid
Character quality:
Character layout:
Rotational angle:
Smoothing:
Standard
Adjusted to the base line
0°
Valid
Top offset:
0/180”
Underline:
Canceled
Character set:
Right and left margins:
Page length:
Enlarged character mode selected
Enlarged character mode selected
Enlarged character mode selected
Enlarged character mode selected
Top and bottom margins:
84
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(6) Arrangement of enlarged characters: DC4 DC4 a
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
a
61
97
n
n
n
Function: Specifies the standard position for adjusting enlarged
characters in the vertical direction.
n = 00H, 30H: Base line is adjusted to the N’th dot from the top.
(N = 20 x cell expansion)
01H, 31H:
02H, 32H:
03H, 33H:
Descender is adjusted to the N’th dot from the
top. (N = 24 x cell expansion)
Center is adjusted to the N’th dot from the top.
(N = 12 x cell expansion)
Ascender is adjusted to the N’th dot from the top.
(N = 1 x cell expansion)
The MSB of the parameter is masked. Any parameters other than those
shown above are ignored.
The arrangement and position specified here are valid if the enlarged
character rotational angle is not 0 degree. The default setting is n =
00H,30H.
(7) Cell expansion for enlarged characters: DC4 DC4 c
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
c
63
99
n
n
n
Function: Specifies cell expansion for enlarged characters.
≤
≤
0
n
127
The cell has the size of (24/180” x cell expansion). The MSB of the
parameter is masked.
If n = 0, the expansion specified in the setup mode is selected.
The cell expansion is specified at the beginning of the line. If there is
character data on the line, it becomes valid on the following line.
Enlarged character cell expansion takes priority over the height expansion.
If the height expansion exceeds cell expansion when enlarged character
data is input, the characters are enlarged to the cell expansion value.
The default setting is the expansion specified in the setup mode.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(8) All-character set for enlarged characters: DC4 DC4 d
Format:
ASCII
DC4
DC4
14
20
d
64
100
n
n
n
d1
d1
d1
d2...dn
d2...dh
d2...dn
Hex
14
Decimal
20
Function: Specifies the all-character set for enlarged characters.
≤
≤
≤
≤
1
0
n
d
255
255
Data with a number specified with the parameter “n” is processed as
character codes. If n = 0, this sequence is ignored.
(9) Selecting an enlarged character font: DC4 DC4 f
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
f
66
102
n
n
n
Function: Specifies the font (typeface) of enlarged characters as shown
below.
n = 0: Roman
1: Sans Serif
2: Courier
3: Prestige
4: Script
5: OCR-B
6: OCR-A
7: Gothic
8: Orator
9: Orator-S
The MSB of the parameter is masked. Any parameters other than those
shown above are ignored.
If the FONT LOCK option is set to YES in the EXTENDED SETUP
MODE, this command is ignored.
The default is the setting selected in the setup mode.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(10) Height expansion for enlarged characters: DC4 DC4 h
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
h
68
104
n
n
n
Function: Specifies the height expansion of enlarged characters.
≤
≤
0
n
127
The MSB of the parameter is masked.
If n = 0, the expansion specified in the setup mode is selected.
Enlarged character cell expansion takes priority over height expansion. If
the height expansion exceeds the cell expansion when enlarged character
data is input, the characters are enlarged to the cell expansion.
The default setting is the expansion specified in the setup mode.
(11) HMI for enlarged characters: DC4 DC4 i
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
i
69
105
n1
n1
n1
n2
n2
n2
Function: Specifies the HMI (horizontal motion index) of enlarged
characters.
≤
≤
≤
0
0
n1 255
≤
n2 15
The HMI indicates the horizontal distance between two adjacent
characters, i.e., the width the print head moves after printing one
character.
The HMI is (n1 + n2 x 256)/180”.
The high-order four bits of parameter n2 (bit 7 to bit 4) are ignored. The
HMI can be set to zero.
After specifed command have priority over DC4 DC4 p or DC4 DC4 i.
If the PITCH LOCK option is set to YES in the setup mode, this
command is ignored.
The default setting is “10 cpi x width expansion”.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(12) VMI for enlarged characters: DC4 DC4 j
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
j
6A
106
n1 n2
n1 n2
n1
n2
Function: Specifies the VMI (vertical motion index) of enlarged
characters.
≤
≤
≤
0
0
n1 255
≤
n2 127
The VMI indicates the distance between two lines, i.e., the length the print
head moves after printing one line.
The VMI is (n1 + n2 x 256)/180”. The MSB of parameter n2 is masked.
The VMI can be set to zero.
The VMI is not dependent on the length expansion of enlarged characters.
After specifed command have priority over DC4 DC4 j or DC4 DC4 o.
The VMI is invalid and the cell offset 6 line feed pitch is selected (i.e.,
1/6” x cell expansion) by default.
(13) Setting and canceling the enlarged character mode: DC4 DC4 l
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
l
6C
108
n
n
n
Function: Sets and cancels the enlarged character mode.
n = 00H, 30H: Cancels the enlarged character mode.
01H, 31H: Sets the enlarged character mode.
The MSB of the parameter is masked. Any sequences other than the
above parameters are ignored.
When the enlarged character mode establish command is issued, the
special effects, character pitch, line feed pitch, length and width double-
size printing settings specified for the emulation become invalid the
enlarged character mode is canceled.
When the enlarged character mode starts, characters are printed in the
conditions selected when the enlarged character mode was last canceled.
If there are non-enlarged characters or bar codes when enlarge character
data is input the non-enlarged character are printed.
In the enlarged character mode, automatic printing is not performed if the
printing position exceeds the right margin. Excess data is abandoned and
the printing position is set at the right margin when the right margin is
exceeded.
If the right margin is exceeded while a single enlarged character is being
printed, the character is printed up to the right margin.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(14) Enlarged character cell offset: DC4 DC4 o
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
o
6F
111
n
n
n
Function: Specifies the cell offset for enlarged characters.
≤
≤
0
n
255
This command specifies the cell offset for the enlarged characters in
1/180”. The cell offset is used to execute a line feed (LF) command.
In the enlarged character mode, the line is fed by a pitch of (24 + cell
offset)/180” x cell expansion.
The VMI is invalid and the cell offset is 6 by default.
(15) Enlarged character pitch: DC4 DC4 p
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
p
70
112
n
n
n
Function: Specifies the pitch of enlarged characters.
n = 00H, 30H: 10 cpi
01H, 31H: 12 cpi
02H, 32H: Proportional
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
If the fixed pitch is selected, enlarged characters have the following width:
10 cpi: (18 180”) x width expansion
x
12 cpi: (15 180”) x width expansion
x
In the proportional mode, proportional characters are expanded by the
same ratio.
When the rotational angle for enlarged characters is set to 90 or 270
degrees, characters other than graphic character are printed at a pitch of
(24/180”) x length expansion. If the PITCH LOCK option is set to YES in
the setup mode, this command is ignored.
The HMI is invalidated and the character pitch is 10 cpi by default.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(16) Enlarged character quality: DC4 DC4 q
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
q
71
113
n
n
n
Function: Specifies the quality of enlarged characters as shown below.
n = 00H, 30H: Standard quality
01H, 31H: High-speed 1 quality
02H, 32H: High-speed 2 quality
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
The character quality is specified at the beginning of a line. If there is
character data on the line, this command is reserved and becomes valid on
the following line.
If the QUALITY LOCK option is set to YES in the setup mode, this
command is ignored.
The standard quality is selected by default.
(17) Enlarged character rotational angle: DC4 DC4 r
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
r
72
114
n
n
n
Function: Specifies the rotational angle of enlarged characters as shown
below.
n = 00H, 30H
01H, 31H
02H, 32H
03H, 33H
0°
90°
180°
270°
Enlarged characters are rotated counterclockwise.
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
Printing starts from the position specified with the DC4 DC4 a command
shown above.
Unless the rotational angle is set to 0 degree, no characters are underlined
even when underlines are input.
Pixels are printed at a rotational angle of 0 degree even if the rotational
angle is set to 90, 180, or 270 degrees.
This command is ignored if the PITCH LOCK option is set to YES in the
EXTENDED SETUP MODE and the length and width expansion values of
enlarged characters are different.
The default rotational angle is 0 degree.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(18) Setting and canceling enlarged character smoothing: DC4 DC4 s
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
s
73
115
n
n
n
Function: Sets and cancels smoothing of enlarged characters.
n = 00H, 30H: Cancels smoothing.
01H, 31H: Sets smoothing.
The MSB of the parameter is masked. Any sequences other than the
above parameters are ignored.
Smoothing is set by default.
(19) Enlarged character top offset: DC4 DC4 t
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
t
74
116
m
m
m
n1
n1
n1
n2
n2
n2
Function: Specifies the top offset of enlarged characters.
m = (20)H
≤
≤
≤
0
0
n1 255
≤
n1 15
The top offset refers to the vertical distance between the top of the cell
and the top of a character. This determines the character position in the
cell.
It is specified by (n1 + n2 x 256)/180”.
The high-order four bits of parameter n2 (bit 7 to bit 4) are masked.
The top offset is effective for only one characterafter this sequence.
The top offset is canceled when a line feed (LF) command, form feed (FF)
command, or vertical print position (DC4 DC4 y) command is issued.
The top offset is not dependent on the enlarged character arrangement.
It is always based on the top of the cell (corresponding to the ascender-
based position).
The top offset is not dependent on cell expansion or length expansion.
The bottom of a character (i.e., 24th pin position, regardless of character
type, even for a 30-dot pixel) does not extend beyond the bottom of the
cell. If the top offset is too large and the bottom of the character extends
below the bottom of the cell, the top offset is reduced.
Any sequences other than m = 20H are ignored.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
(20) Setting and canceling underline for enlarged characters: DC4 DC4 u
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
u
75
117
n
n
n
Function: Sets and cancels the underline function.
n = 00H, 30H: Cancels underlining.
01H, 31H: Specifies the underlining.
The MSB of the parameter is masked. Any sequences other than the
above parameters are ignored.
An underline is drawn on the 25th pin line at a thickness of (1 dot x length
expansion of the character).
No underlines are printed if the enlarged character rotational angle is not
set to 0 degree. Underscoring is off by default.
(21) Enlarged character width expansion: DC4 DC4 w
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
w
77
119
n
n
n
Function: Specifies the width expansion of enlarged characters.
≤
≤
0
n
127
The MSB of the parameter is masked.
If n is set to 0, the expansion specified in the setup mode is selected.
This command is ignored if the PITCH LOCK option is set to YES in the
EXTENDED SETUP MODE.
The expansion specified in the setup mode is set by default.
(22) Horizontal printing position for enlarged characters: DC4 DC4 x
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
x
78
120
m
m
m
n1
n1
n1 n2
n2
n2
Function: Specifies the horizontal position for printing enlarged
characters by (n1 + n2 x 256)/180” as shown below.
m = SP(20)H:
-(2D)H: Relative lefthand printing position
+(2B)H: Relative righthand printing position
Absolute printing position
≤
≤
≤
0
0
n1 255
≤
n2 15
The MSB of parameter m and the four high-order bits of n2 (bit 7 to bit 4)
are masked.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
If parameter m is different than shown above, this sequence is ignored.
The absolute print position is based on the left margin. If the specified
position exceeds the right margin, the print position is located at the right
margin.
If a relative lefthand printing position to the left of the left margin is
specified, left margin becomes the printing position.
If a relative righthand printing position to the right of the right margin is
specified, the right margin becomes the printing position.
The movement distance is not dependent on the width expansion of
enlarged characters.
(23) Vertical printing position for enlarged characters: DC4 DC4 y
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
y
79
121
m
m
m
n1 n2
n1 n2
n1 n2
Function: Specifies the vertical position for printing enlarged characters
by (n1 + n2 x 256)/180” as shown below.
m = SP(20)H:
-(2D)H: Relative reverse printing position
+(2B)H: Relative forward printing position
Absolute printing position
≤
≤
≤
≤
0
0
n1
n2
255
127
The MSBs of parameters m and n2 are masked. If parameter m is other
than shown above, this sequence is ignored.
The absolute print position is based on the TOF position. If the specified
position extends below the bottom margin, the bottom margin becomes
the print position.
If a relative reverse printing position exceeding the TOF position is
specified, the TOF position becomes the print position.
If a relative forward printing position that extends below the bottom
margin is specified, the print position is located at the bottom margin.
The movement distance is not dependent on the length expansion of
enlarged characters.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Bar code and enlarged character
Enlarged character print samples
This page shows examples of a BASIC program for printing enlarged
characters and the printed enlarged characters (actual size).
100 OPEN "LPT1:"AS #1
110 DC4$=CHR$(&H14)
120 '
130 PRINT #1, DC4$;DC4$;"@";
140 PRINT #1,DC4$;DC4$;"c";CHR$(8);
150 PRINT #1,DC4$;DC4$;"f";CHR$(4);
160 PRINT #1,DC4$;DC4$;"p";CHR$(1);
170 PRINT #1,DC4$;DC4$;"l";CHR$(1);
180 '
'
'
'
'
'
Initializing
Expansion of cell: x8
Font typeface: SCRIPT
Character pitch: 12 CPI
Expansion mode on
190 PRINT #1,"8";
'
Default size print
200 PRINT #1,DC4$;DC4$;"h";CHR$(2); ' Vertical expansion: x2
210 PRINT #1,DC4$;DC4$;"w";CHR$(2);
220 PRINT #1,DC4$;DC4$;"a";CHR$(3);
230 PRINT #1,"ASCE";
'
'
Horizontal expansion: x2
Alignment: ascender
240 PRINT #1,DC4$;DC4$;"a";CHR$(2);
250 PRINT #1,"CENT";
260 PRINT #1,DC4$;DC4$;"a";CHR$(1);
270 PRINT #1,"DESC";
280 PRINT #1,DC4$;DC4$;"a";CHR$(0);
290 PRINT #1,"BASE";
'
'
'
Alignment: center
Alignment: descender
Alignment: baseline
300 '
310 PRINT #1,DC4$;DC4$;"w";CHR$(8);
320 PRINT #1,"H";
330 PRINT #1,DC4$;DC4$;"w";CHR$(1);
340 FOR N=1 TO 8
350 PRINT #1,DC4$;DC4$;"h";CHR$(N);
360 PRINT #1,RIGHT$;(STR$(N),1); '
370 NEXT N
'
'
'
Horizontal expansion: x8
Horizontal expansion: x1
Vertical expansion: xn
380 PRINT #1,DC4$;DC4$;"w";CHR$(8); ' Horizontal expansion: x8
390 PRINT #1,DC4$;DC4$;"r";CHR$(1); Rotate: 90 degree
400 PRINT #1, "R"
'
;
410 PRINT #1,CHR$;(13);CHR$(10); ' CR+LF
420 '
430 PRINT #1,DC4$;DC4$;"l";CHR$(0);
440 CLOSE #1
'
Expansion mode off
450 END
94
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
Appendix A. Specifications
❏ Printing specifications
•
•
Impact dot matrix and bidirectional logic seeking printing
Printing method
Print Head
24 pins, movable-type (parallel/staggered orientation.)
Estimated life expectancy: 500 million dots/wire
•
•
•
Epson LQ-2550
IBM 2391
Hewlett Packard RuggedWriter 480
Emulation
•
•
Draft, High quality draft, Speed draft, Super speed draft
Roman, Sans Serif, Courier, Prestige, Script, OCR-B, OCR-
A, Gothic, Orator, Orator-S
Resident fonts
•
•
•
Epson character sets (up to 128 characters downloadable)
IBM character sets and code pages (32kB download area)
HP character sets (up to 256 characters (32kB)
downloadable)
Down load character sets
Bit Image Printing (EPSON/IBM)
11 Categories (8 or 24 pin graphics):
dpi: dot per inch
Graphic printing
•
•
•
•
•
•
•
•
•
60 dpi
80 dpi — 8-pin only
90 dpi
120 dpi — 8-pin only *
120 dpi
180 dpi — 24-pin only
240 dpi — 8-pin only *
360 dpi — 24-pin only *
360 dpi — 48-pin only (IBM mode) *
* Horizontally adjacent dots can not be printed.
Raster Graphics Printing (HP)
4 Categories:
•
•
•
•
60 dpi (60h x 60v dpi), raster graphic mode
90 dpi (90h x 90v dpi), raster graphic mode
180 dpi (180h x 180v dpi), raster graphic mode
360 dpi (360h x 360v dpi), raster graphic mode
Character spacings
•
•
•
•
•
•
•
•
•
10 cpi Pica print mode
Print mode
12 cpi Elite, Speed draft print mode
15 cpi Super speed draft print mode
16.7 cpi Condensed print mode
17.1 cpi Condensed pica print mode
20 cpi Condensed elite print mode
24 cpi print mode
Proportional print mode
One half proportional print mode
95
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
Character Tables in the EPSON mode
•
•
•
Italic character table
Graphic character table
Graphic character table, extended
Character table (EPSON mode)
Character Tables in the IBM mode
•
•
•
IBM character set 1 table
IBM character set 2 table
IBM all character set table
(IBM mode)
(HP mode)
Character Tables in the HP mode
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ROMAN-8 (8U)
PC-8 (10U)
PC-850 (12U)
ECMA 94
LATIN1 (ISO 8859-1 , 0N)
PC-8 DENMARK/NORWAY (11U)
LINE-DRAW (0L,0B)
MATH-7 (0A, 0M)
ROMAN-EXTENSION (0E)
SWEDEN 1 (ISO-10, 0S)
SWEDEN 2 (ISO-11, 3S)
NORWAY 1 (ISO-60, 0D)
NORWAY 2 (ISO-61, 1D)
UK (ISO-4, 1E)
FRANCE 2 (ISO-25, 0F)
FRANCE 1 (ISO-69, 1F)
GERMAN 2 (0G)
GERMAN 1 (ISO-21, 1G)
ITALY (ISO-15, 0I)
SPAIN 3 (1S)
SPAIN 1 (ISO-17, 2S)
SPAIN 2 (ISO-85, 6S)
PORTUGAL 1 (ISO-16, 4S)
PORTUGAL 2 (ISO-84, 5S)
IRV (ISO-2, 2U)
JAPAN (ISO-14, 0K)
ASCII (ISO-6, 0U)
LEGAL (1U)
USA, FRANCE, GERMANY, U.K., DENMARK, SWEDEN,
ITALY, SPAIN, JAPAN, NORWAY, DENMARK2, SPAIN2,
LATIN-AMERICAN, KOREA, TURKEY, LEGAL
International character set
(EPSON mode)
437(USA), 850(MULTILINGUAL), 857(TURKEY), 858,
860(PORTUGUESE), 861, 863(CANADA-FRENCH), 865
(NORDIC), BRASCII, ABICOMP, ISO-8859-1
Codepage Character table
(HP, EPSON, IBM mode)
Industrial 2 of 5, Interleaved 2 of 5, Matrix 2 of 5,
Codabar, Code 11, Code 39, Code 93, Code 128, EAN 8,
EAN 13, UPC-A, UPC-E, and Postnet.
Barcode type
(HP, EPSON, IBM mode)
•
•
•
•
•
•
Draft (10cpi) :
HQDR (10cpi) :
NLQ (10cpi) :
LQ (10cpi) :
Speed draft (Elite) : 220 lpm
Super speed draft :
195 lpm
165 lpm
120 lpm
97 lpm
Throughput
235 lpm
96
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
Throughput
Evaluation conditions:
Data of 100 lines by 132 columns, all ASCII rolling
pattern characters, and 1/6-inch line feed is input from a
host and is stored in the 64K-byte communication buffer
of the printer. With that condition, the number of
printing lines per minute is measured.
Paper feed method
Paper width
Paper weight
Friction method:
•
•
•
•
Single cut sheet (A3, B4, A4, B5, letter, legal)
55 kg - 90 kg in Japan
17 lbs. - 28 lbs. in USA
64 g/m2 - 105 g/m2 in Europe
Tractor method:
•
•
•
45 kg - 90 kg in Japan
14 lbs. - 28 lbs. in USA
53 g/m2 - 105 g/m2 in Europe
CSF mode (option):
•
•
•
55 kg - 70 kg in Japan
15 lbs. - 21 lbs. in USA
60 g/m2 - 81 g/m2 in Europe
Label paper
•
•
Paper stiffness of less than 125 kg or equivalent
Total thickness of less than 0.12 mm
Multiple copies
•
•
Original plus 5, non-carbon, 34 Kg or equivalent
Total thickness of less than 0.35 mm
Line feed pitch
Line feed speed
Print speed
•
•
•
Minimum of 1/360 inch
60 lines/second (6 lines/inch)
Super Speed Draft (15 cpi): 900 cps (character per
second)
•
•
•
•
•
Speed Draft (12 cpi):
Draft Pica (10 cpi):
HQDR Pica (10 cpi):
NLQ Pica (10 cpi):
LQ Pica (10 cpi):
720 cps
600 cps
473 cps
315 cps
236 cps
Recommended
print area
Single sheet Paper
Fanfold Paper
TOF
TOF Adjustment
14/60 inch (6 mm)
Print
recommended
area
Print
recommended
area
for
continuous form
for single sheets
Override BM
17 mm
Perforation
Near perforation
1 inch (25.4 mm)
Override BM
4 inches (101.6 m
Final form
13 mm
13 mm
97
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
Print mode specifications
Note: (+n) indicates the number of space added.
Dot
Spacing
(inches)
Max No.
of
Columns
Character
Structure
(V x H)
Printing
Speed
(cps)
Print mode
10 cpi
12 cpi
1/180 x 1/90
1/180 x 1/144
1/180 x 1/180
1/180 x 1/240
1/180 x 1/240
1/180 x 1/240
1/180 x 1/360
1/180 x 1/144
1/180 x 1/360
1/180 x 1/120
1/180 x 1/120
1/180 x 1/120
1/180 x 1/144
1/180 x 1/180
1/180 x 1/240
1/180 x 1/240
1/180 x 1/240
1/180 x 1/360
1/180 x 1/144
136
163
204
227
233
272
326
----
----
163
204
136
163
204
227
233
272
326
----
24 x 8
24 x 12
600
473
473
395
404
473
567
----
----
720
900
473
473
473
395
404
473
567
----
----
315
378
15 cpi
24 x 12
Draft
16.7 cpi
17 cpi
24 x 12(+2.3)
24 x 12(+2)
24 x 12
20 cpi
24 cpi
24 x 12(+3)
24 x N
Proportional
1/2 Proportional
12 cpi
24 x N
Speed Draft
24 x 8(+2)
24 x 8
S.Speed Draft 15 cpi
10 cpi
12 cpi
24 x 12
24 x 12
15 cpi
HQDR
24 x 12
16.7 cpi
24 x 12(+2.3)
24 x 12(+2)
24 x 12
17 cpi
20 cpi
24 cpi
24 x 12(+3)
24 x N
Proportional
1/2 Proportional
10 cpi
1/180 x 1/360
1/180 x 1/360
----
136
24 x N
x
24 36
12 cpi
1/180 x 1/360
1/180 x 1/360
163
204
24 x 30
15 cpi
(EPSON)
x
16 24
473
354
15 cpi
(HP/IBM)
x
1/180 x 1/720
204
24 36(+12)
Near Letter
Quality
16.7 cpi
17 cpi
1/180 x 1/720
1/180 x 1/720
1/180 x 1/720
227
233
272
24 x 36(+7)
24 x 36(+6)
24 x 30(+6)
395
404
473
20 cpi
24 cpi
(EPSON)
x
1/180 x 1/720
326
16 24(+6)
567
24 cpi
x
1/180 x 1/720
1/180 x 1/360
1/180 x 1/720
326
----
----
24 30
567
----
----
(HP/IBM)
x
x
Proportional
24
24
N
N
1/2 Proportional
98
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
Note: (+n) indicates the number of space added.
Dot
Spacing
(V X H)
Max No.
of
Columns
Character
Structure
(V X H)
Printing
Speed
(cps)
Print mode
10 cpi
12 cpi
1/180 x 1/360
1/180 x 1/360
1/180 x 1/360
136
163
204
24 x 36
24 x 30
16 x 24
236
284
354
15 cpi
(EPSON)
15 cpi
(HP/IBM)
1/180 x 1/720
204
24 x 36(+12)
354
Letter
Quality
16.7 cpi
17 cpi
1/180 x 1/720
1/180 x 1/720
1/180 x 1/720
1/180 x 1/720
227
233
272
326
24 x 36(+7)
24 x 36(+6)
24 x 30(+6)
16 x 24(+6)
395
404
473
567
20 cpi
24 cpi
(EPSON)
24 cpi
(HP/IBM)
1/180 x 1/720
326
24 x 24(+6)
567
Proportional
1/180 x 1/360
1/180 x 1/720
----
----
24 x N
----
----
1/2 Proportional
24 x N
Graphic Print Specifications
Graphic type
Density Pins
60dpi
Horizontal
dot pitch
Print speed (inch / second)
MODE 1
47.3
MODE 2 MODE 3 / High speed 1 High speed 2/3
8/24
8
1/60 inch
1/80 inch
1/90 inch
1/60 inch
1/120 inch
1/180 inch
1/120 inch
1/180 inch
47.3
35.4
31.5
47.3
23.6
23.6
23.6
23.6
47.3
35.4
31.5
47.3
47.3
31.5
47.3
31.5
47.3
35.4
31.5
47.3
47.3
47.3
47.3
47.3
80dpi
35.4
31.5
47.3
23.6
90dpi
8/24
8
8/24
24
8
120dpi
120dpi
180dpi
240dpi
360dpi
15.8
23.6
15.8
24
MODE 1, 2 or 3 is set by “31 GRAPHIC QUALITY”.
High speed 1 or 2 is set by the QUALITY key or “23 QUALITY”.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
❏ Parallel interface specifications
•
Input connector (36-pin parallel)
18171615141312 1110 9
8
7
6
5
4
3
2
1
363534333231302928272625242322212019
PIN
1
SIGNAL
STROBE
IN/OUT
IN
PIN
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
SIGNAL
GND
IN/OUT
2
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
ACK
IN
GND
3
IN
GND
4
IN
GND
5
IN
GND
6
IN
GND
7
IN
GND
8
IN
GND
9
IN
GND
10
11
12
13
14
15
16
17
18
OUT
OUT
OUT
OUT
IN
GND
BUSY
GND
PE
HIGH
INITIAL
ERROR
HIGH
NC
SELECT
AUTOFEED
HIGH
IN
OUT
LOW
CHASSIS GND
HIGH
HIGH
SELECT IN
IN
Notes:
1. HIGH is pulled up to + 5V by 2.2k Ω resistor.
2. LOW is pulled down to GND by 2.2kΩ resistor.
3. NC stands for no connection.
4. CHASSIS GND and GND are connected in the printer.
5. SELECT IN signal is HIGH to accept a control code.
Bidirectional (IEEE1284 Nibble mode) is available.
•
Data input timing chart and input condition
Data input
STROBE
DATA1-8
AUTO FEED
SELECT IN
+5V
74LS04
or equivalent
2.2k
DATA 1-8
Input
BUSY
ACK
+5V
0 µs min.
STORBE
74LS14
or equivalent
1 µs
max.
2.2k
100
4-6µs
1 µs min.
4-6 µs
1 µs min.
1-50 µs
7 - 10 µs
Input
Input
330pF
Initialization
+5V
INITIAL
74LS14
or equivalent
INITIAL
2.2k
100
BUSY
ACK
50 µs max.
50 µs min.
4-6 µs
4-6 µs
1000pF
7 - 10 µs
Inside printer
100
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
❏ Serial interface specifications
•
Input connector (25-pin serial)
13
1
25
14
RS-232C Pin assignments
PIN
1
SIGNAL
IN/OUT
PIN
14
15
16
17
18
19
20
21
22
23
24
25
SIGNAL IN/OUT
CHASSIS GND
NC
NC
NC
NC
NC
NC
2
TXD
RXD
OUT
IN
3
4
RTS
OUT
IN
5
CTS
6
DSR
IN
7
SIGNAL GND
CD
DTR
NC
OUT
8
IN
9
NC
NC
10
11
12
13
NC
NC
SRTS
NC
OUT
NC
INC
NC
Notes:
1. NC stands for no connection.
2. CHASSIS GND and GND are connected in the printer.
•
•
Handshake protocol
One of the following four protocols can be selected:
- DTR protocol (Busy/Ready protocol)
- X ON/X OFF protocol I
- X ON/X OFF protocol II
- ETX/ACK protocol
Logic level
ON=Space (0)=High:
12V (+3 through +15V)
OFF=Mark (1)=LOW:
Input signal
75189 or equivalent
Input
330pF
-12V (-3 through -15V)
Output signal
75188 or equivalent
Output
Inside printer
•
Baud Rate
In the setup options, one of the following baud rates can be selected:
300, 600, 1200, 2400, 4800, 9600, 19200, and 38400 BPS.
Data frame
+3 +15V
D2
D1
D3 D4 D5 D6 D7 D8
STOP
START
-3 -15V
101
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Specifications
❏ Other specifications
•
•
64k byte, 8k byte, 128 byte
(Changeable buffer size from the setup #71)
Buffer size
2 levels of fan speed control capability
Cooling fan
•
•
100 - 120VAC:
220 - 240VAC:
For Japan, USA and Canada
For Australia, Asia, Europe and Others
Power supply
•
•
41°F - 104°F (during Operation)
5°C - 40°C
Temperature
•
20 % - 80 % RH (no condensation)
Humidity
[Model A]
External dimensions
•
24.4"(Width) x 10.2"(Height) x 12.0"(Depth)
620(W) x 260(H) x 305(D) mm
With the paper rack and sound seal cover
24.4"(W) x 11.6"(H) x 17.9"(D)
620(W) x 295(H) x 455(D) mm
•
[Model B]
•
24.4"(Width) x 10.2"(Height) x 13.0"(Depth)
620(W) x 260(H) x 330(D) mm
With the paper rack and sound seal cover
24.4"(W) x 11.6"(H) x 18.9"(D)
620(W) x 295(H) x 480(D) mm
•
•
•
Approximately 21 kg [46.3 lbs.]
Weight
LQ self test
Power Consumption
100-120 V AC 4.2A(320 watts)
220-240 V AC 1.9A(300 watts)
stand - by
100-120 V AC 0.5A(36 watts)
220-240 V AC 0.3A(36 watts)
sleeping mode
•
•
100-120 V AC 0.2A(12 watts)
220-240 V AC 0.1A(12 watts)
102
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
Appendix B. Control code summary
❏ IBM mode
ITEM SYMBOL
Hexadecimal & Decimal
FUNCTION
[1]
[2]
BEL
BS
[07] H [7] D
[08] H [8] D
Activates the alarm.
Backspaces one character.
[3]
HT
[09] H [9] D
Moves to next horizontal tab.
[4]
LF
[0A] H [10] D
[0B] H [11] D
[0C] H [12] D
[0D] H [13] D
[0E] H [14] D
[0F] H [15] D
[11] H [17] D
[12] H [18] D
[14] H [20] D
[18] H [24] D
[1B,19,n] H [27,25,n] D
Linefeeds after printing.
[5]
VT
Linefeeds to next vertical tab position after printing.
Form feeds after printing.
[6]
FF
[7]
CR
Carriage return after printing.
[8]
SO
Sets double width character mode for 1 line.
Sets condensed pica character mode (17.1 cpi).
Selects printer that has been deselected by ESC Q (23).
Selects pica (10cpi) mode.
[9]
SI
[10]
[11]
[12]
[13]
[14]
DC1
DC2
DC4
CAN
ESC EM n
Cancels double width character mode set by SO.
Clears data in buffer.
Control cut sheet feeder.
n=1: selects bin 1
n=2: selects bin 2
n=R: ejects single sheet paper loaded in the priner
This command is effective at the following conditions.
The paper select lever is set to the single sheet setting.
#49 CSF OPTION is set to SINGLE or DOUBLE.
[15]
ESC *m n1 n2
[1B,2A,m,n1,n2] H
[27,42,m,n1,n2] D
Sets various graphic modes.
This command is effective only when AGM mode is
set to ON in the extended setup options.
m
Graphic Type
Number
Maximum Horizontal
of Pins
Columns
816
Density
60
120
120
240
80
90
60
120
90
180
360
0
1
2
3
4
Standard-density
Double-density
Double-speed double-density*
Quadruple-density *
CRT I
8
8
8
8
8
1632
1632
3264
1088
1224
816
1632
1224
2448
4896
6
CRT II
8
32
33
38
39
40
Standard-density
Double-density
CRT III
Triple-density
Quadruple-density*
24
24
24
24
24
Note (*): Horizontal adjacent dots can not be printed.
The total column number is calculated by n1+n2 × 256 for 8-pin graphics and
(n1+n2×256) x 3 for 24-pin graphics.
Each bit data in the 8-pin graphics corresponds to 2 print pins of the print head.
The following figure shows one column of data and its corresponding print position.
Bit Data (MSB)
1
1
1
0
1
1
1
(LSB)
0
Print Pin (Top)
(Bottom)
[16]
ESC – n
[1B,2D,n] H [27,45,n] D
Sets or cancels underline mode.
n=0: underline is cancelled.
n=1: underline is set.
[17]
[18]
[19]
[20]
ESC 0
ESC 1
ESC 2
ESC 3 n
[1B,30] H [27,48] D
[1B,31] H [27,49] D
[1B,32] H [27,50] D
[1B,33,n] H [27,51,n] D
Sets line spacing to 1/8".
Sets line spacing to 7/72".
Linefeeds with the line spacing set by ESC A.
Sets line spacing in the basic spacing set by ESC [ \.
The default is n/216" (1≤n≤255) in standard mode
or n/180" (0≤n≤255) in AGM mode.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[21]
[22]
ESC 4
[1B,34] H [27,52] D
Sets the top-of-form (TOF) at the current print line.
ESC 5 n
[1B,35,n] H [27,53,n] D
Sets/cancels auto linefeed with CR
n=0: Carriage return without linefeed.
n=1: Carriage return with linefeed.
[23]
[24]
[25]
[26]
ESC 6
ESC 7
ESC :
[1B,36] H [27,54] D
[1B,37] H [27,55] D
[1B,3A] H [27,58] D
Selects IBM character set 2.
Selects IBM character set 1.
Sets elite (12cpi) mode.
ESC = n1 n2
id lo hi data
[1B,3D,n1,n2,23,lo,hi] H
[27,61,n1,n2,35,lo,hi] D
Defines download character.
When n1=n2=0, the download area is cleared.
The number of data bytes following n2 is defined as
n1+n2×256 (including three bytes of id, lo, hi ).
id is always 23h.
lo and hi compose two-byte address where the first
downloading character is to be stored and the follow-
ing data are stored in the successive addresses.
[27]
[28]
[29]
ESC A n
[1B,41,n] H [27,65,n] D
Sets line spacing to n/72" (1≤n≤255)
or to n/60" (1≤n≤255) in AGM mode.
ESC B n1 n2...
n64 NUL
[1B,42,n1,n2,...n64,00] H
[27,66,n1,n2,...n64,0] D
Sets vertical tab positions beginning from n1 and end
with NUL [00]H. n1=1 is the first line at the TOF.
ESC C n
[1B,43,n] H [27,67,n] D
Sets page length in lines (1≤n≤255).
The current print line becomes TOF (top-of-form).
The bottom margin set by ESC N is cancelled.
[30]
[31]
ESC C NUL n
[1B,43,00,n] H [27,67,0,n] D
Sets page length in inches (1≤n≤182).
The current print line becomes TOF (top of form).
ESC D n1
n2...n28 NUL
[1B,44,n1,n2,...n28,00] H
[27,68,n1,n2,...n28,0] D
Sets horizontal tab position (1≤n≤255).
n indicates the number of spaces from the left margin
with the character width at the command execution.
Left/right margins clear the tab positions.
n1=1 is at the first column from the left margin.
[32]
ESC E
[1B,45] H [27,69] D
Sets emphasized character mode.
Underline and graphic characters are also emphasized.
[33]
[34]
ESC F
ESC G
[1B,46] H [27,70] D
[1B,47] H [27,71] D
Cancels emphasized character mode.
Sets double strike character mode.
[35]
[36]
ESC H
ESC I n
[1B,48]H [27,72] D
[1B,49] H [27,73] D
Cancels double strike character mode.
Selects one of font styles.
n=0: draft 10cpi
n=2: LQ 10cpi
n=3: LQ proportional
n=4: download Draft 10cpi
n=6: download LQ 10cpi
n=7: download LQ proportional
n=8: draft 12cpi
n=10: LQ 12cpi
n=12: download draft 12cpi
n=14: download LQ 12cpi
n=16: condensed draft
n=18: condensed LQ
n=20: download condensed draft
n=22: download condensed LQ
[37]
ESC J n
[1B,4A,n] H [27,74,n] D
Linefeeds in the basic spacing set by ESC [ \ after
printing. The default is n/216" (1≤n≤255) in
standard mode or n/180" (0≤n≤255) in AGM mode.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[38]
ESC K n1 n2
data
[1B,4B,n1,n2,data] H
[27,75,n1,n2,data] D
Prints the 8-pin Standard-density graphic mode(60dpi)
The total number of dots in the data is set by
n1+n2×256.
[39]
ESC L n1 n2
data
[1B,4C,n1,n2,data] H
[27,76,n1,n2,data] D
Prints the 8-pin Double-density graphic mode(120dpi)
The total number of dots in the data is set by
n1+n2×256.
[40]
ESC N n
[1B,4E,n] H [27,78,n] D
Sets bottom margin (1≤n≤255).
n specifies the number of lines not to be printed at the
end of a page.
For example: If the line spacing is 1/6 inch and the page length is 66 lines,
an ESC N 6 command causes the printer to print 60 lines, then skip 6 lines.
The space to be skipped is 1 inch (1/6 inch 6).
x
[41]
[42]
ESC O
[1B,4F] H [27,79] D
[1B,50] H [27,80] D
Cancels the bottom margin set by ESC N.
ESC P n
Sets/cancels proportional mode.
n=0: the proportional mode is cancelled
n=1: the proportional mode is selected
[43]
ESC Q n
[1B,51,23] H [27,81,35] D
Deselects the printer. DC1 selects the printer.
n=23h: the printer is deselected
n≠23h: this command is ignored
[44]
[45]
ESC R
[1B,52] H [27,82] D
Initializes horizontal tabs to every 8th column
starting from 9th column and clears vertical tabs.
ESC S n
[1B,53,n] H [27,83,n] D
Sets superscript or subscript character mode.
n=0: the superscript character mode is set
n=1: the subscript character mode is set
[46]
[47]
ESC T
[1B,54] H [27,84] D
Cancels super/subscript character mode.
ESC U n
[1B,55,n] H [27,85,n] D
Sets or cancels unidirectional printing.
n=0: the unidirectional printing is cancelled and the
bidirectional or predirectional is set according
to the setup options
n=1: unidirectional printing is set
[48]
[49]
[50]
[51]
ESC W n
[1B,57,n] H [27,87,n] D
Sets or cancels double width character mode.
n=0: the double width character mode is cancelled
n=1: the double width character mode is set
ESC X n m
[1B,5C,n,m] H
[27,92,n,m] D
Sets left and right margins (0≤n<m≤255)
n: left margin, m: right margin
The print area is between the nth and mth column.
ESC Y n1 n2
data
[1B,59,n1,n2,data] H
[27,89,n1,n2,data] D
Prints 8-pin double-speed double-density graphic
mode (120dpi). The total number of dots in the data is
set by n1+n2×256.
Prints 8-pin quadruple-density graphic mode (240dpi).
The total number of dots in the data is set by
ESC Z n1 n2
data
[1B,5A,n1,n2,data] H
[27,90,n1,n2,data] D
n1 + n2 256.
x
[52]
ESC [ - n1 n2
m1 m2
[1B,5B,2D,n1,n2,m1,m2] H
[27,91,45,n1,n2,m1,m2] D
Sets various line modes.
n1=2 and n2=0
m1=01h:
m1=02h:
m1=03h:
Underline is set
Strike-through is set
Overscore is set
m2=00h:
m2=01h:
m2=02h:
m2=FFh:
line mode at m1 is cancelled
Single line is set
Double line is set
all line modes are cancelled
105
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
ITEM SYMBOL
[53] ESC [ @ n1 n2
Hexadecimal Decimal
FUNCTION
[1B,5B,40,n1,n2,m1,..,m4] H
[27,91,64,n1,n2,m1,..,m4] D
Sets single or double height/width/line-spacing mode.
n1=4, n2=0, and m2=0.
m1...m4
m1=00h: no change
m1=01h: italic style is set
m1=02h: italic style is cancelled
m1=04h: outline style is set
m1=08h: outline style is cancelled
m1=10h: shadow style is set
m1=20h: shadow style is cancelled
m3=00h: no change
m3=01h: single character height
m3=02h: double character height
m3=10h: single line spacing
m3=11h: single char. height/single line spacing
m3=12h: double char. height/single line spacing
m3=20h: double line spacing
m3=21h: single char. height/double line spacing
m3=22h: double char. height/double line spacing
m4=00h: no change
m4=01h: single character width.
m4=02h: double character width.
Selects character attributes (font, character spacing/
size, and/or code page in the following format.
The number of parameter bytes following n1 and n2
is defined by n1+n2×256.
[54]
ESC [ I n1 n2
Hf, Lf, Hs, Ls
Sm, 00, Hc, Lc
[1B,5B,49,n1,n2,Hf,Lf,
Hs,Ls,Sm,00,Hc,Lc] H
[27,91,73,n1,n2,Hf,Lf,
1. Select a font, character style, and spacing in the following tables: (n1=2 and n2=0)
Normal Character Style Table (Hf: Upper byte, Lf: Lower byte)
Hf/Lf (Hex)
10cpi
12cpi
15cpi
17cpi
20cpi
24cpi
Proportional
Courier
Prestige
Gothic
Orator-S
Orator
Script
00/0B
00/0C
00/24
00/19
00/05
01/D4
01/EB
01/EF
01/8F
01/D0
01/CB
01/D5
01/EC
01/F0
01/8E
01/D1
01/CC
01/D6
01/ED
01/C9
01/8D
01/D2
01/CD
01/D7
01/EE
01/CA
01/8C
01/D3
01/CE
01/D8
01/1E
01/1F
01/20
01/23
01/21
01/24
01/AB
00/A4
00/AE
00/C7
00/C6
00/C8
Various Character Style Table (Hf: Upper byte, Lf: Lower byte)
Character Styles Normal
Hf/Lf (Hex)
Italic
Emphasized Emphasized Double-Width Double-Width Double-Width
Italic
Double-Height Double-Height Double-Height
Emphasized Double-Strike
Courier 10 cpi
Courier 12 cpi
Courier 15 cpi
Courier 17 cpi
Courier Prop.
Prestige 10 cpi
Prestige 12 cpi
Prestige 15 cpi
Prestige 17 cpi
Gothic 10 cpi
Gothic 12 cpi
Gothic 15 cpi
Gothic 17 cpi
Gothic 20 cpi
Gothic Prop.
—
00/12
00/5C
00/D7
—
00/AC
—
00/70
—
—
—
00/6D
—
—
—
00/2E
00/6C
00/D6
00/FD
00/B8
00/3C
00/6F
—
—
—
00/6E
—
—
00/39
00/74
00/D8
—
00/B9
—
—
—
—
—
00/F4
—
—
—
—
—
—
—
—
00/F1
—
—
—
—
00/F5
—
—
—
—
—
—
—
—
00/F2
—
—
—
—
—
—
—
—
—
—
—
—
—
00/F3
—
—
—
—
00/55
00/DF
00/FE
—
—
00/56
00/DD
01/00
—
00/57
00/DE
00/FF
01/19
—
—
—
—
—
—
00/9D
00/A2
—
—
—
—
106
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
2. Select a character style, and spacing in the following tables (Hf, Lf is ignored):
(n1=6, n2=0, Hf=0, Lf=0, and S=1)
Character Spacing and Style Table (Hs: Upper byte, Ls: Lower byte)
Hs
Ls
Hs
Ls
00
00
00
00
00-41 24 cpi, Subscript
42-4D 20 cpi, Subscript
4E-59 17 cpi, Normal
5A-6B 15 cpi, Normal
00
00
00
00
84-9B 10 cpi, Normal
9C-B3 17 cpi, Double-Width
B4-D7 15 cpi, Double-Width
D8-FE 12 cpi, Double-Width, Double-
Height
3. Select a proportional spaced character: (n1=6, n2=0, Hf=Lf=Hc=Lc, and S=2)
(n1=6, n2=0, Hf=Lf=Hc=Lc="Don't care", and S=2 or 3)
4. Select a code page in the following tables:
(n1=8, n2=0, and Hf=Lf=Hc=Lc=S="Don't care")
Code Page Table (Hc: Upper byte, Lc: Lower byte)
Hc
Lc
Code page
01h B5h
03h 52h
03h 5Ch
03h 5Fh
03h 61h
03h 59h
40h 00h
03h 5Ah
03h 5Dh
437
850
860
863
865
857
ISO-1
858
861
0Fh 07h BRASCII
0Fh 08h ABICOMP
[55]
ESC [ K n1 n2
m1...m4
[1B,5B,4B,n1,n2,m1,..,m4] H
[27,92,75,n1,n2,m1,..,m4] D
Software initialization.
The number of data bytes following n2 is defined as
n1+n2×256.
Code
Initialize condition
m1
m2
00h, 04h, FEh
01h, 05h, FFh
03h, 16h, 23h
24h, B1h, B4
initializes without clearing download area
initializes with clearing download area
indicates information defined by m3 and m4
following m2.
m3 and m4 indicates the combination of each parameters:
m3
m4
bit7 valid (0) or invalid (1) of m3
valid (0) or invalid (1) of m4
bit6
bit5
—
—
Code page 437 (0) or 850 (1)
—
bit4 LF=LF (0) or LF=CR+LF (1)
bit3 CR=CR (0) or CR=CR+LF (1)
bit2 Page length of 11" (0) or 12" (1)
bit1 Non-slash zero (0) or
—
—
—
Print line width of 13.6" (0) or 8" (1)
slashed zero (1)
bit0 Character set 1 (0) or set 2 (1)
—
[56]
ESC [ T n1 n2
m1...m4
[1B,5B,54,n1,n2,m1,..,m4] H
[27,92,84,n1,n2,m1,..,m4] D
Selects code page.
n1=4, n2=0, m1=0, and m2=0.
m3 m4 Code page
m3
m4 Code page
01h B5h
03h 52h
03h 5Ch
03h 5Fh
03h 61h
03h 59h
40h 00h
437
850
860
863
865
03h 5Ah
03h 5Dh
0Fh 07h BRASCII
0Fh 08h ABICOMP
858
861
857
ISO-1
107
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (IBM)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[57]
ESC [ \ n1 n2
m1...m4
[1B,5B,5C,n1,n2,m1,...m4] H
[27,91,92,n1,n2,m1,...m4] D
Sets basic line spacing to 1/180", 1/216", or 1/360".
n1=4, n2=0, m1=0, and m2=0
The basic line spacing affects the amount of the line
feeding at ESC J and ESC 3.
m3
m4
Basic line spacing
180
216
104
0
0
1
1/180" line spacing (AGM)
1/216" line spacing
1/360" line spacing
[58]
[59]
ESC [ d n1 n2
m
[1B,5B,64,n1,n2,m] H
[27,91,100,n1,n2,m] D
Selects print character quality.
n1=1 and n2=0
m=00h: no change
m=01h-7Fh: draft character quality
m=80h-BFh and FFh: LQ character quality
m=C0h-FEh: emphasized LQ character quality
ESC [ g n1 n2
m data
[1B,5B,67,n1,n2,m,data] H
[27,91,103,n1,n2,m,data] D
Sets various graphic modes.
m
Graphic Type
Number
of Pins
Maximum Horizontal
Columns
Density
0
1
2
3
8
Standard-density
Double-density
Double-speed double-density **
Quadruple-density **
Standard-density
Double-density
Triple-density
Hex-density**
Hex-density**
8
8
8
816
1632
1632
3264
816
1632
2448
4896
4896
60
120
120
240
60
120
180
360
360
8
24
24
24
24
48
9
11
12
16
Note (**): Horizontal adjacent dots can not be printed.
The number of data bytes following n1 and n2 is defined as the total column number for
8-pin graphics (one byte/column) plus one extra parameter byte (m). 24-pin graphics
takes three bytes/column and 48-pin graphics takes six bytes/column.
Each bit data in the 8-pin and 48-pin graphics corresponds to 2 print pins of the print
head. The following figure shows one column of data and its corresponding print
position.
Bit Data (MSB)
Print Pin (Top)
1
1
1
1
0
0
1
(LSB)
1
(Bottom)
*)
Note ( : These pins become active when both adjacent print pins are activated.
[60]
ESC \ n1 n2
data
[1B,5C,n1,n2,data] H
[1B,92,n1,n2,data] D
Prints characters from all character set.
The number of character to be printed is defined by
n1+n2×256.
[61]
[62]
ESC ]
[1B,5D] H [27,92] D
Reverse line feeds by the current line spacing.
ESC ^ n
[1B,5E,n] H [27,94,n] D
Prints one character (n: character code) from all
character set.
[63]
ESC _ n
[1B,5F,n] H [27,95,n] D
Sets or cancels overscore mode.
n=0: the overscore mode is cancelled
n=1: the overscore mode is set
[64]
[65]
ESC d n1 n2
ESC j
[1B,64,n1,n2] H
[27,100,n1,n2] D
Sets relative print position.
(n1+n2×256)/120" from current position
Stops printing and sets the printer in offline.
[1B,6A] H [27,106] D
108
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
❏ EPSON mode
ITEM SYMBOL
Hexadecimal & Decimal
FUNCTION
[1]
[2]
BEL
BS
[07] H [7] D
[08] H [8] D
Activates the bell.
Backspace one character.
[3]
HT
[09] H [9] D
Moves to next horizontal tab.
[4]
[5]
[6]
[7]
[8]
LF
VT
FF
CR
[0A] H [10] D
[0B ]H [11] D
[0C] H [12] D
[0D] H [13] D
Linefeeds after printing.
Linefeeds to next vertical tab position after printing.
Form feeds after printing.
Carriage return after printing.
SO
[0E] H [14] D
Sets double width character mode for 1 line.
ESC SO
[1B,0E] H [27,14] D
DC4, LF, FF, ESC N, and ESC ! cancel this mode.
[9]
SI
[0F] H [15] D
Sets condensed character mode.
ESC SI
[1B,0F] H [27,15] D
10 and 12 cpi becomes 17.1 and 20 cpi, respectively.
[10]
[11]
[12]
[13]
[14]
DC1
DC2
DC3
DC4
CAN
[11] H [17] D
[12] H [18] D
[13] H [19] D
[14] H [20] D
[18] H [24] D
Selects printer that has been deselected by DC3.
Cancels condensed character mode.
Deselects printer.
Cancels double width character mode set by SO.
Clears data in buffer and move print head to home
position.
[15]
[16]
DEL
[7F] H [127] D
Deletes one character.
ESC EM n
[1B,19,n] H [27,25,n] D
Controls cut sheet feeder.
n=1: selects bin 1
n=2: selects bin 2
n=R: ejects single sheet paper loaded in the printer
This command is effective at the following conditions.
The paper select lever is set to the single sheet setting.
#49 CSF OPTION is set to SINGLE or DOUBLE.
[17]
[18]
ESC SP n
ESC ! n
[1B,20,n] H [27,32,n] D
0≤n≤127
Sets intercharacter space in dot units.
The dot width in pica mode is 1/120 inch.
Print mode
Dot width
1/120 inch
1/180 inch
Draft
LQ/Proportional
[1B,21,n] H [27,33,n] D
Sets multiple print modes.
n is specified by the following bit combination.
(0≤n≤255)
Print modes
Pica
Elite
Proportional
Condensed
Emphasized
Double strike
Double width
Italic
Dec.
0
Hex.
00
01
02
04
08
10
20
40
80
Correspond command
ESC P
ESC M
ESC p
SI, DC1
ESC E, ESC F
ESC G, ESC H
ESC W
ESC 4, ESC 5
ESC -
1
2
4
8
16
32
64
128
Underline
[19]
ESC #
[1B,23] H [27,35] D
Cancels MSB control set by ESC = or ESC >.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[20]
[21]
[22]
ESC $ n1 n2
[1B,24,n1,n2] H
[27,36,n1,n2] D
Sets absolute dot position. The dot spacing is 1/60"
and its position is n1+n2x256 dots from the left
margin.
ESC % n
[1B,25,n] H [27,37,n] D
Sets resident characters or download characters.
n=0 : the resident character set is set.
n=1 : the download character set is set.
ESC & NUL n
m a0 a1 a2 data
[1B,26,00,n,m,a0,a1,a2,data] H
[27,38,0,n,m,a0,a1,a2,data] D
Defines download character(s).
n:
m:
first code of download character (00-127)
last code of download character (00-127)
a0: front space (00-255)
a1: body length
(draft: 00-15, LQ/proportional: 00-37)
a2: rear space (00-127)
Note: Total character spacing is limited as;
0 < a0+a1 (+a2) < 42 for LQ/proportional, and
0 < a0+a1 (+a2) < 18 for draft.
PIN 1
MSB
PIN 8
PIN 9
3 bytes
PIN 16
PIN 17
LSB
PIN 24
Front Space
(0-255)
Body
(0-15, 0-37)
Rear Space
(0-127)
Note: Super/subscript downloading character needs
two bytes in each vertical dot column (height).
[23]
ESC ( - n1 n2
m d1 d2
[1B,28,2D,n1,n2,m,d1,d2] H
[27,40,45,n1,n2,m,d1,d2] D
Sets various line modes.
n1=3, n2=0, and m=1
d1=01h:
d1=02h:
d1=03h:
Underline is set.
Strike-through is set.
Overscore is set.
d2=00h:
d2=01h:
d2=02h:
d2=05h:
d2=06h:
Line mode is cancelled.
Single line is set.
Double line is set.
Single broken line is set.
Double broken line is set.
[24]
[25]
ESC ( ^ n1 n2
data
[1B,28,5E,n1,n2,data] H
[27,40,94,n1,n2,data] D
Prints character from all character set table.
The number of character following n2 to be printed is
defined by n1+n2x256.
This command is valid only when the character table
is set to CODE PAGE in the extended setup options.
ESC (t
n1n2 d1 d2 d3
[27,40,116,n1 n2 d1 d2 d3] D
[1B,28,74,n1 n2 d1 d2 d3] H
Specifies a character set.
d1:Displys ESC tn command table No.
d2, d3:Specifies the character set.
d2=0,d3=0 : ITALIC
d2=1,d3=0 : PC-437
d2=3,d3=0 : PC-850
d2=7,d3=0 : PC-860
110
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
d2=8,d3=0 : PC-863
d2=9,d3=0 : PC-865
d2=11,d3=0 : PC-857
d2=17,d3=0 : ISO-8859-1
Sets various graphic modes.
d2=44,d3=0 : PC-858
d2=24,d3=0 : PC-861
d2=25,d3=0 : BRASCII
d2=26,d3=0 : ABICOMP
[26]
ESC *m n1 n2
data
[1B,2A,m,n1,n2,data] H
[27,42,m,n1,n2,data] D
m
Graphic Type
Number
Maximum Horizontal
of Pins
Columns
816
Density
60
120
120
240
80
90
60
120
90
180
360
0
1
2
3
4
Standard-density
Double-density
Double-speed double-density*
Quadruple-density *
CRT I
8
8
8
8
8
1632
1632
3264
1088
1224
816
1632
1224
2448
4896
6
CRT II
8
32
33
38
39
40
Standard-density
Double-density
CRT III
Triple-density
Hex-density*
24
24
24
24
24
Note (*): Horizontal adjacent dots can not be printed.
The total column number is calculated by n1+n2 x 256 for 8-pin graphics and
(n1 + n2x256) x3 for 24-pin graphics.
Each bit data in the 8-pin graphics corresponds to 2 print pins of the print head.
The following figure shows one column of data and its corresponding print position.
Bit Data (MSB)
1
1
1
0
1
1
1
(LSB)
0
Print Pin (Top)
(Bottom)
[27]
[28]
ESC + n
ESC - n
[1B,2B,n] H [27,43,n] D
[1B,2D,n] H [27,45,n] D
Sets line spacing to n/360" (0≤n≤255).
Sets or cancels underline.
n=0: underline is cancelled
n=1: underline is set
[29]
[30]
[31]
[32]
[33]
ESC / c
ESC 0
ESC 2
ESC 3 n
ESC 4
[1B,2F,c] H [27,47,c] D
[1B,30] H [27,48] D
[1B,32] H [27,50] D
[1B,33,n] H [27,51,n] D
[1B,34] H [27,52] D
Selects a channel (c: 0-7) of vertical tab.
Sets line spacing to 1/8".
Sets line spacing to 1/6".
Sets line spacing to n/180" (0≤n≤255).
Sets italic character mode.
Download characters and graphic characters
(B0h-DFh, F4h, and F5h) are not italicized.
[34]
[35]
ESC 5
ESC 6
[1B,35] H [27,53] D
[1B,36] H [27,54] D
Cancels italic character mode.
Enlarges the print code area.
Control code area (80h-9Fh) is printed as characters.
[36]
[37]
ESC 7
[1B,37] H [27,55] D
Clears ESC 6 command.
ESC : NUL
n NUL
[1B,3A,00,n,00] H
[27,58,0,n,0] D
Copy RAM download character set from ROM
character set.
n=00h: ROMAN is copied
n=01h: SANS SERIF is copied
n=02h: COURIER is copied
n=03h: PRESTIGE is copied
n=04h: SCRIPT is copied
n=05h: OCR-B is copied
n=06h: OCR-A is copied
n=07h: ORATOR is copied
n=08h: ORATOR-S is copied
n=14h: GOTHIC is copied
[38]
[39]
[40]
ESC <
ESC =
ESC >
[1B,3C] H [27,60] D
[1B,3D] H [27,61] D
[1B,3E] H [27,62] D
Moves print head to home position.
Sets MSB of data to "0".
Sets MSB of data to "1".
111
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[41]
ESC ? n m
[1B,3F,n,m] H
[27,63,n,m] D
Re-assign graphic type for ESC K, ESC L,
ESC Y, and ESC Z commands.
n: specifies the former graphic type assigned
by "K", "L", "Y", or "Z"
m: specifies the new graphic type in table below
m
Graphic Type
Number
Maximum Horizontal
of Pins
Columns
816
Density
60
120
120
240
80
90
60
120
90
180
360
0
1
2
3
4
Standard-density
Double-density
Double-speed double-density*
Quadruple-density *
CRT I
8
8
8
8
8
1632
1632
3264
1088
1224
816
1632
1224
2448
4896
6
CRT II
8
32
33
38
39
40
Standard-density
Double-density
CRT III
Triple-density
Hex-density*
24
24
24
24
24
Note (*): Horizontal adjacent dots can not be printed.
[42]
[43]
[44]
ESC @
[1B,40] H [27,64] D
Initializes printer.
Sets line spacing to n/60" (0≤n≤127).
Sets vertical tab positions beginning from n1 and end
with NUL [00]H. n1=1 is at the second line from TOF.
Downloaded data and communication buffer are not
cleared. The current print line becomes the top of the
form.
ESC A n
[1B,41,n] H [27,65,n] D
ESC B n1 n2...
n16 NUL
[1B,42,n1,n2,...n16,00] H
[27,66,n1,n2,...n16,0] D
[45]
[46]
[47]
ESC C n
[1B,43,n] H [27,67,n] D
Sets page length in line unit (1≤n≤127).
The current print line becomes TOF (top of form).
ESC C NUL n
[1B,43,00,n] H [27,67,0,n] D
Sets page length in inch unit (1≤n≤22).
The current print line becomes TOF (top of form).
ESC D n1
n2...n32 NUL
[1B,44,n1,n2,...n32,00] H
[27,68,n1,n2,...n32,0] D
Sets horizontal tab position (1≤n≤255).
n indicates the number of spaces from the left margin
with the character width at the command execution.
n1=1 is at the second column from the left margin.
[48]
[49]
[50]
[51]
[52]
[53]
ESC E
ESC F
ESC G
ESC H
ESC J n
[1B,45] H [27,69] D
[1B,46] H [27,70] D
[1B,47] H [27,71] D
[1B,48]H [27,72] D
[1B,4A,n] H [27,74,n] D
Sets emphasized character mode.
Cancels emphasized character mode.
Sets double strike character mode.
Cancels double strike character mode.
n/180" linefeeds after printing (0≤n≤255).
ESC K n1 n2
data
[1B,4B,n1,n2,data] H
[27,75,n1,n2,data] D
Prints the 8-pin Standard-density graphic mode.
The total number of dots in the data is set by
n1+n2 256.
x
[54]
[55]
[56]
ESC L n1 n2
data
[1B,4C,n1,n2,data] H
[27,76,n1,n2,data] D
Prints the 8-pin Double-density graphic mode.
The total number of dots in the data is set by
n1+n2 256.
x
ESC M
[1B,4D] H [27,77] D
Selects elite (12cpi) mode.
The condensed pica character (17.1 cpi) also becomes
the condensed elite character (20 cpi).
ESC N n
[1B,4E,n] H [27,78,n] D
Sets skip over perforation (1≤n≤127).
n specifies the number of lines to be skipped at the
end of a page.
For example: If the line spacing is 1/6 inch and the page length is 66 lines,
an ESC N 6 command causes the printer to print 60 lines, then skip 6 lines.
The space to be skipped is 1 inch (1/6 inch 6).
x
112
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[57]
ESC O
[1B,4F] H [27,79] D
Cancels skip over perforation.
[58]
ESC P
[1B,50] H [27,80] D
Selects pica mode (10cpi).
The condensed elite character (20 cpi) also becomes
the condensed pica character (17.1 cpi).
[59]
[60]
ESC Q n
ESC R n
[1B,51,n] H [27,81,n] D
[1B,52,n] H [27,82,n] D
Sets right margin at the nth horizontal space in the
current print mode from the left-most print position.
(1≤n≤255)
Selects International character.
n
Country
Hexadecimal Character Code
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
0
1
2
3
4
5
6
7
8
9
U.S.A.
#
#
#
£
#
#
#
Pt
#
#
#
#
#
#
#
#
$
$
$
$
$
€
$
$
$
€
$
$
$
$
ı
$
@
à
§
@
@
É
@
@
@
É
É
á
á
[
°
Ä
[
Æ
Ä
°
¡
[
Æ
Æ
¡
¡
[
Ç
°
\
ç
Ö
\
Ø
ö
\
Ñ
]
§
Ü
]
Å
Å
é
¿
]
Å
Å
¿
¿
]
ˆ
ˆ
ˆ
ˆ
ˆ
Ü
ˆ
ˆ
ˆ
Ü
Ü
é
é
ˆ
Ü
¶
`
`
`
`
`
é
ù
`
`
è
è
`
ü
`
{
é
ä
{
æ
ä
à
¨
{
æ
æ
í
í
{
ç
©
|
ù
ö
|
ø
ö
ò
ñ
|
ø
ø
ñ
ñ
|
ö
®
}
è
ü
}
å
å
è
}
}
å
å
ó
ó
}
s,
†
~
¨
ß
~
~
ü
ì
~
~
ü
ü
ú
ú
~
ü
™
FRANCE
GERMANY
U.K.
DENMARK
SWEDEN
ITALY
SPAIN
JAPAN
NORWAY
Ø
Ø
Ñ
Ñ
10 DENMARK 2
11 SPAIN 2
12 LATIN AMERICA
13 KOREA
31 TURKEY
64 LEGAL
—
—
W
@
.
v
I
Ö
'
S
g
`
,
§
"
Note: n=64 is invalid when code page is selected.
[61]
ESC S n
[1B,53,n] H [27,83,n] D
Sets superscript or subscript character mode
n=0: the superscript character mode is set
n=1: the subscript character mode is set
[62]
[63]
ESC T
[1B,54] H [27,84] D
Cancels super/subscript character mode printing.
ESC U n
[1B,55,n] H [27,85,n] D
Sets or cancels unidirectional printing.
n=0: the unidirectional printing is cancelled and the
bidirectional or predirectional is set according
to the setup options
n=1: unidirectional printing is set
[64]
[65]
[66]
[67]
ESC W n
[1B,57,n] H [27,87,n] D
Sets or cancels double width character mode
n=0: the double width character mode is cancelled
n=1: the double width character mode is set
ESC Y n1 n2
data
[1B,59,n1,n2] H
[27,89,n1,n2] D
Prints 8-pin double-speed double-density graphic
mode (120dpi). The total number of dots in the data is
set by n1+n2 256.
x
ESC Z n1 n2
data
[1B,5A,n1,n2] H
[27,90,n1,n2] D
Prints 8-pin quadruple-density graphic mode (240dpi).
The total number of dots in the data is set by
n1+n2 256.
x
ESC \ n1 n2
[1B,5C,n1,n2] H
[27,92,n1,n2] D
Sets relative dot position to the current position.
The dot spacing is 1/120 inch in draft mode and
1/180 inch in LQ/proportional mode.
For Example:
If n1+n2 256< 32768 (8000h), then move n1+n2 256 dots to the right.
x
x
If n1+n2 256 ≥ 32768, then move 65536 - {n1+n2 256} dots to the left
x
x
from the current position.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Epson)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[68]
ESC a n
[1B,61,n] H [27,97,n] D
Justification mode.
n=0: left justification is set (default)
n=1: centering is set
n=2: right justification is set
n=3: full justification is set
When n is other than 0, the printer performs one
linefeed after printing.
[69]
ESC b c n1 n2
...n16 NUL
[1B,62,c,n1,n2,...,n16,00] H
[27,98,c,n1,n2,...,n16,0] D
Sets vertical tab position in channels beginning from
n1 and end with NUL [00]H as in ESC b command.
c specifies one of channels 0 to 7 to be set.
[70]
[71]
ESC g
[1B,67] H [27,103] D
Sets 15cpi mode.
ESC j n
[1B,6A,n] H [27,106,n] D
n/180" reverse linefeed after printing (0≤n≤255).
This command is ignored in the cut sheet feeder mode.
[72]
ESC k n
[1B,6B,n] H [27,107,n] D
Selects font type.
n=00h: ROMAN is selected
n=01h: SANS SERIF is selected
n=02h: COURIER is selected
n=03h: PRESTIGE is selected
n=04h: SCRIPT is selected
n=05h: OCR-B is selected
n=06h: OCR-A is selected
n=07h: ORATOR is selected
n=08h: ORATOR-S is selected
n=14h: GOTHIC is selected
Sets left margin at the nth horizontal space in the
current print mode.
[73]
ESC l n
[1B,6C,n] H [27,108,n] D
The left margin can be set a distance of up to 8" from
the left end of the carriage.
[74]
[75]
ESC p n
ESC q n
[1B,70,n] H [27,112,n] D
[1B,71,n] H [27,113,n] D
Sets or cancels proportional mode.
n=0: the proportional mode is cancelled
n=1: the proportional mode is set
Sets character style.
n=0: plain style is set
n=1: outline style is set
n=2: shadow style is set
n=3: outline with shadow style is set
Selects character code table.
[76]
ESC t n
[1B,74,n] H [27,116,n]D
n=00,30:Selects the italic character table.
n=01,31:Selects the graphic character table.
n=02,32:Selects the downloaded character table.
n=03,33:Selects the graphic character table.
If downloaded characters cannot be printed when the
downloaded character table is selected, italic
characters are printed. The selected character table is
chantged eith the ETS(t command.
[77]
[78]
ESC w n
ESC x n
[1B,77,n] H [27,119,n] D
[1B,78,n] H [27,120,n] D
Sets or cancels double height character mode.
n=0: the double height character mode is cancelled
n=1: the double height character mode is set
Selects character quality.
n=0: draft character mode is set
n=1: LQ character mode is set
114
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
❏ PCL mode
ITEM SYMBOL
Hexadecimal & Decimal
[07] H [7] D
[08] H [8] D
FUNCTION
Activates the bell. (Valid for PCL3+, PCL+D)
Backspace one character.
[1]
BEL
[2]
BS
[3]
[4]
HT
LF
[09] H [9] D
Moves to next horizontal tab.
Linefeeds after printing.
[0A] H [10] D
[0B] H [11] D
[0C] H [12] D
[0D] H [13] D
[0E] H [14] D
[0F] H [15] D
[1B] H [27] D
[20] H [32] D
[7F] H [127] D
[1B,26,61,#,43]H
[27,38,97,#,67]D
[1B,26,61,#,48]H
[27,38,97,#,72]D
[1B,26,61,#,4C]H
[27,38,97,#,76]D
[1B,26,61,#,4D]H
[27,38,97,#,77]D
[1B,26,61,#,52]H
[27,38,97,#,82]D
[1B,26,61,#,56]H
[27,38,97,#,86]D
[1B,26,64,#,44]H
[27,38,100,#,68]D
[1B,26,64,40]H
[27,38,100,64]D
[1B,26,6B,#,45]H
[27,38,107,#,69]D
[1B,26,6B,#,46]H
[27,38,107,#,70]D
[5]
[6]
[7]
[8]
VT
FF
CR
SO
SI
ESC
SP
DEL
Linefeeds to next vertical tab position after printing.
Form feeds after printing.
Carriage return after printing.
Selects secondary font.
Selects primary font.
Designate start of escape sequence.
Space one character.
[9]
[10]
[11]
[12]
[13]
To print the ASCII DEL character.
Horizontal positioning by column.
ESC & a # C
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
ESC & a # H
ESC & a # L
ESC & a # M
ESC & a # R
ESC & a # V
ESC & d # D
ESC & d @
Horizontal positioning by 1/720".
Sets left margin.
Sets right margin.
Vertical positioning by VMI.
Vertical positioning by 1/720".
Designate underline mode.
Cancel underline mode.
ESC & k # E
ESC & k # F
Designates/Cancels the auto- cancellation of underline.
Designates/Cancels the auto- cancellation of secondary font.
Note: If # is set to "0" , current secondary font set
changes automatically to primary font when vertical
position changes .
[23]
[24]
ESC & k # G
ESC & k # H
[1B,26,6B,#,47]H
[27,38,107,#,71]D
Designates line termination .
# = 0 (30H) :CR=CR,LF=LF,FF=FF
# = 1 (31H) :CR=CR+LF,LF=LF,FF=FF
# = 2 (32H) :CR=CR,LF=LF+CR,FF=FF+CR
# = 3 (33H) :CR=CR+LF,LF=LF+CR,FF=FF+CR
[1B,26,6B,#,48]H
[27,38,107,#,72]D
Sets HMI(Horizontal motion index ).
- HMI is set by 1/120 inch.
- HMI is defined as the distance where the
print position moves when the character code
is input. If # is 12, the input characters are
printed in 10 cpi.
[25]
ESC & k # S
[1B,26,6B,#,53] H
[27,38,107,#,83] D
Designates character spacing.
- Character spacing is set.
# = 0 (30H) :Normal (10 cpi)
# = 1 (31H) :Double width(5 cpi)
# = 2 (32H) :Compressed (16.7 cpi)
# = 4 (34H) :12 cpi spacing
115
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[26]
ESC & k # W
[1B,26,6B,#,57] D
[27,38,107,#,87] D
Controls print direction. (Valid for PCL3+, PCL+D)
- Print direction is set as follows.
# = 0 (30H) :Unidirectional Print(left to right)
# = 1 (31H) :Bidirectional Print
# = 2 (32H) :Pre-directional Print
[27]
ESC & l # A
[1B,26,6C,#,41] H
[27,38,108,#,65] D
Designates paper size.
- Paper size is set as follows.
# = 0 (30H) :(Setting in the setup mode)
# = 2 (32H) :Letter
# = 3 (33H) :Legal
# = 26 (32H,36H) :A4
# = 81 (38H,31H) :ENVELOP Business(Com 10)
[28]
ESC & l # C
[1B,26,6C,#,43] H
[27,38,108,#,67] D
Sets VMI(Vertical motion index).
- VMI is set by 1/48 inch.
- VMI is defined as the distance where the
print position moves when the LF code is
input. If # is 8, the print position moves in 6
lpi vertically.
[29]
[30]
ESC & l # D
ESC & l # E
[1B,26,6C,#,44] H
[27,38,108,#,68] D
Sets the line spacing. VMI(Vertical motion index)
# = The number of LPI (lines per inch).
ex. # = 8 (38H) :8 LPI
[1B,26,6C,#,45] H
[27,38,108,#,69] D
Sets Top margin by VMI. (where # = “1 , 2 ,...)
When the top margin is set, the text length to be default.
In case of Skip perforation ON
Text length = page length- Top margin-1/2"
(Bottom margin set to 1/2")
In case of Skip perforation OFF
Text length = page length- Top margin
(Bottom margin set to 0")
Sets Text length.
- Text length is set by line by VMI.
Sets paper path.
[31]
[32]
ESC & l # F
ESC & l # H
[1B,26,6C,#,46] H
[27,38,108,#,70] D
[1B,26,6C,#,48] H
[27,38,108,#,72] D
- The mode set as follows.
# = 0 (30H) :Eject Paper
# = 1 (31H) :Feed from BIN 1
# = 2 (32H) :Feed from manual insertion
# = -1 (2DH,31H) :Select fanfold paper
# = 8 : BIN 2
# = 9 : BIN1+2
Note:When the "NOT INSTALLED" is selected in the
" SETUP #49 CSF OPTIONS" the CSF command is the
same as #=0.
[33]
ESC & l # L
data
[1B,26,6C,#,4C] H
[27,38,108,#,76] D
Designates/Cancels skip perforation mode.
- Paper path is set as follows.
# = 0 (30H) :Cancels the mode
# = 1 (31H) :Designates the mode
[34]
[35]
[36]
ESC & l # P
ESC & p # X
ESC & s # C
[1B,26,6C,#,50] H
[27,38,108,#,80] D
[1B,26,70,#,58] H
[27,38,112,#,88] D
[1B,26,73,#,43] H
[27,38,115,#,67] D
Sets page length by VMI.
Receives data as text.
Designates/Cancels wraparound..
# = 0 (30H) :Designates wraparound
# = 1 (31H) :Cancels wraparound
116
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
Assign font to the primary/secondary font set.
[37]
ESC ( # id
ESC ) # id
[1B,28,#,id] H [27,40,#,id] D
[1B,29,#,id] H [27,41,#,id] D
# id
8 U
0 U
0 N
10U
12U
11U
0 S
3 S
0 D
1 D
1 E
1 F
1 G
0 I
Font
ROMAN-8
ASCII
ECMA-94,LATIN1(ISO8859.1)
PC-8 (PC-437)
# id
4 S
2 U
0 K
1 U
0 L
0 M
0 A
0 E
Font
ISO,PORTUGAL 1
ISO,IRV
ISO14, JIS, ASCII
LEGAL
PC-850
LINE-DRAW
MATH7
PC-8,DENMARK/NORWAY
ISO11,SWEDEN 1
ISO10,SWEDEN 2
ISO60,NORWAY 1
ISO61,NORWAY 2
ISO4,UK
ISO69,FRANCE 1
ISO21,GERMANY 1
ISO15,ITALY
ISO17,SPAIN 1
LINE-DRAW
ISO25,FRANCE 2
GERMAN 2
MATH-SYMBOL
ROMAN-EXTENSION
ISO84,PORTUGAL 2
ISO85,SPAIN 2
PC-857
PC-858
PC-860
PC-861
PC-863
5 S
6 S
80U
93U
81U
94U
82U
83U
95U
96U
2 S
0 B
0 F
0 G
1 S
PC-865
BRASCII
ABICOMP
SPAIN 3
The 12U,0F,0G,1S,1U,0M,0A,5S and 6S are
available only when PCL3+ or PCL3+D modes.
[38]
ESC ( # @
[1B,28,#,40] H
[27,40,#,64] D
Designates primary font.
# = 0 or “1 (30H or 31H)
Copy the default primary symbol set to the
current primary symbol set.
# = 2 (32H)
Copy the current primary symbol set to the
current primary symbol set.
# = 3 (33H)
Copy the default primary font to the current
primary font.
[39]
[40]
ESC ( 0 X
ESC ) 0 X
ESC ( s # B
ESC ) s # B
[1B,28,30,58] H [27,40,48,88] D
[1B,29,30,58] H [27,41,48,88] D
[1B,28,73,#,42] H [27,40,115,#,66] D
[1B,29,73,#,42] H [27,41,115,#,66] D
Assigns the download font to the current primary/
secondary font.
Bold or emphasized.
- Designates/Cancels bold or emphasized
attributes as follows.
# = 0 (30H) :Bold off/Emphasized off
# = 3 (33H) :Bold on /Emphasized off
# = 7 (37H) :Bold off/Emphasized on
117
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[41]
ESC ( s # H
ESC ) s # H
[1B,28,73,#,48] H [27,40,115,#,72] D
[1B,29,73,#,48] H [27,41,115,#,72] D
Sets character spacing.(# = Font pitch(CPI))
PCL mode = PCL3+, PCL3+D or PCL3
# = 5
:5 cpi (0.01≤#<5.01)
:10 cpi (5.01≤#<10.01)
:12 cpi (10.01≤#<12.01)
# = 10
# = 12
PCL mode = PCL3+ or PCL3+D
# = 15
# = 16.7
# = 17.1
# = 20
:15 cpi (12.01≤#<15.01)
:16.7 cpi (15.01≤#<16.71)
:17.1 cpi (16.71≤#<17.11)
:20 cpi (17.11≤#<20.01)
:24 cpi (20.01≤#)
# = 24
PCL mode = PCL3
# = 16.7
# = 20
:16.7 cpi (12.01≤#<16.71)
:20 cpi (16.71 ≤#)
[42]
[43]
[44]
ESC ( s # P
ESC ) s # P
[1B,28,73,#,50] H [27,40,115,#,80] D
[1B,29,73,#,50] H [27,41,115,#,80] D
Selects proportional or fixed character spacing
# = 1 (31H) :Proportional pitch
# = 0 (30H) :Fixed pitch
ESC ( s # Q
ESC ) s # Q
[1B,28,73,#,51] H [27,40,115,#,81] D
[1B,29,73,#,51] H [27,41,115,#,81] D
Sets Print quality.
# = 0 (30H) :Draft
# = 2 (32H) :Letter Quality
Sets italic character.
ESC ( s # S
ESC ) s # S
[1B,28,73,#,53] H [27,40,115,#,83] D
[1B,29,73,#,53] H [27,41,115,#,83] D
# = 0 (30H) :Cancels italic character
# = 1 (31H) :Designates italic character
# = 2 (32H) :Designates italic character
Sets typeface.
[45]
ESC ( s # T
ESC ) s # T
[1B,28,73,#,54] H [27,40,115,#,84] D
[1B,29,73,#,54] H [27,41,115,#,84] D
# = 0 (30H) LINE PRINTER DRAFT
# = 3 (33H) COURIER
# = 4 (34H) SANS SERIF
# = 5 (35H) ROMAN
# = 6 (36H) GOTHIC
# = 7 (37H) SCRIPT
*
# = 8 (38H) PRESTIGE
# = 10
# = 11
# = 20
# = 21
ORATOR (31H,30H) *
ORATOR-S (31H,31H)*
OCR-A (32H,30H)
OCR-B (32H,31H)
*
*
*= Available in PCL3+ or PCL3+D
[46]
[47]
ESC ( s # U
ESC ) s # U
[1B,28,73,#,55] H [27,40,115,#,85] D
[1B,29,73,#,55] H [27,41,115,#,85] D
Sets super/Sub-script.
# = + 1 (2BH,31H) :Designates superscript
# = 0 (30H) :Cancels super/subscript
# = - 1 (2DH,31H) :Designates subscript
Sets character point size
# = 1 , 2 (31H,32H) :Other fonts
ESC ( s # V
ESC ) s # V
[1B,28,73,#,56] H [27,40,115,#,86] D
[1B,29,73,#,56] H [27,41,115,#,86] D
# = 8 (38H)
:Micro font
:Other font
# = 9 (31H,32H)
118
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
1B,28,73,#,57] H
[data]
27,40,115,#,87] D
[data]
FUNCTION
Download character descriptor and data.
[48]
ESC ( s # W
[data]
[
[
- The parameter # consists of 3 bytes of the descriptor
<Attribute data format>
1 st
8
0
1
(Attribute format)
2 nd
3 rd
(Continuation)
(Acknowledge for the attribute data)
- Dot pattern data stream is translated as follows;
Data stream
•••••••
AAAAAAAA
CCCCCCCC
BBBBBBBB
1 byte
•••••••
1 byte
1 byte
36 dots
12 dots
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
F
G
G
G
G
G
G
G
G
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
1/360 dpi
1/120 dpi
DRAFT
LQ
[49]
ESC ) # @
[
[
1B,29,#,40] H
27,41,#,64] D
Designates secondary font.
- The default primary font which is currently selected
in the setup mode is set.
# = ”0”(30H)
Copy the default secondary symbol set to the
current secondary symbol set.
# = ”1”(31H)
Copy the default primary symbol set to the
current secondary symbol set.
# = ”2”(32H)
Copy the current primary symbol set to the
current secondary symbol set.
# = ”3”(33H)
Copy the default secondary font to the
current secondary font.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
FUNCTION
[50]
ESC ) s # W
[DATA]
[
[
1B,29,73,#,57] H DATA
27,41,115,#,87] D DATA
Download font descriptor.
- ESC ) s 0 W command resistors a blank LQ font.
The format is as follows
Byte 0-1
Byte 2-3
Byte 3-4
Byte 5-6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Byte 7-8
Byte 9-10
Byte 10-11
Byte 12-13
Byte 14-15
Byte 16-17
Byte 18-19
Byte 20-21
Byte 22-23
Byte 24-25
Byte 26-27
Byte 28-29
[ SYMBOL SET (2 BYTES)]
0
0
[ POINT SIZE (2 BYTES)]
0
0
0
0
0
0
[ TYPEFACE ]
0
0
[LQ/DRAFT]
Symbol set : Byte 14-15 represent the symbol set # and
ID for the download character to be selected by [37]
ESC ( # id command.
Example:Roman-8
8U”
32 x 8 + 85 - 64 = 277 (01H,15H)
Point size(character height): Point size in decimal is
registered.
Typeface:Parameter used in the typeface selection
command is registered.
LQ/DRAFT:Print Quality, LQ or Draft is registered by
the following definition;
0:DRAFT 1:LQ
[51]
ESC * b # M
[
[
1B,2A,62,#,4D] H
27,42,98,#,77] D
Selects format for the graphic data compression.
- Raster graphics data are registered.
(Valid for PCL3+, PCL+D)
# = 0
# = 1
# = 2
# = 3
:compression off
:mode 1
:mode 2
:mode 3
[52]
[53]
[54]
[55]
ESC * b # W
[DATA]
[
[
1B,2A,62,#,57] H DATA
27,42,98,#,87] D DATA
Raster graphic data transmission
- Raster graphics data are registered.
Sets temporary graphics X-offset.
ESC * b # X
[1B,2A,62,#,58]H
[27,42,98,#,88]D
[1B 2A 62 # 59]H
[27 42 98 # 89]D
[1B,2A,63,#,45]H
[27,42,99,#,69]D
ESC * b # Y
ESC * c # E
Sets temporary graphics Y-offset.
Sets download character code.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (HP)
ITEM SYMBOL
Hexadecimal Decimal
[1B,2A,63,#,46]H
[27,42,99,#,70]D
FUNCTION
[56]
ESC * c # F
Download font control
- Controls download font as follows.
# = 0 (30H) :Delete all download font
# = 3 (33H) Delete data of current download
code.
# = 6 (36H) :Copy ROM font to download
font.
[57]
[58]
[59]
ESC * p # X
ESC * p # Y
ESC * r # A
[1B,2A,70,#,58]H
[27,42,112,#,88]D
Sets horizontal positioning by dot
# = 1/180" units : PCL3 or PCL3+
# = 1/360" units : PCL3+ D
Sets vertical positioning by dot
# = 1/180" units : PCL3 or PCL3+
# = 1/360" units : PCL3+ D
[1B,2A,70,#,59]H
[27,42,112,#,89]D
[1B,2A,72,#,41]H
[27,42,114,#,65]D
Sets start raster graphics printing
- Raster graphics printing starts as follows
# = 0(30H) :Prints from the left most
printable position
# = 1(31H) :Prints from the current position
[60]
[61]
ESC * r B
ESC * r K
[1B,2A,72,42]H
[27,42,114,66]D
Sets terminates raster graphics printing
- Raster graphics printing is terminated
[1B,2A,72,4B]H
[27,42,114,65]D
Model number request(Serial I/F only)
- Model number is requested.
- The printer sends back the following answer
when this data is recognized. “2235A 2712CRLF”
[62]
[63]
ESC * r # S
ESC * t # R
[1B,2A,72,#,53]H
[27,42,114,#,83]D
Designates raster graphics width.
- Raster graphics width is defined by dot.
[1B,2A,74,#,52]H
[27,42,117,#,82]D
Designates raster graphics resolution.
-Raster graphics resolution is defined as follows.
When PCL3+ or PCL3+D is selected.
# = 6 , 0 (36H,30H)
# = 9 , 0 (39H,30H)
:60 dpi
:90 dpi
# = 1 , 8 , 0 (31H,38H,30H) :180 dpi
# = 3 , 6 , 0 (33H,36H,30H) :360 dpi
When PCL3 is selected.
# = 9 , 0 (39H,30H)
# = 1 , 8 , 0 (31H,38H,30H) :180 dpi
Clear left and right margin.
:90 dpi
[64]
[65]
[66]
ESC 9
[1B,39]H [27,57]D
ESC =
[1B,3D]H [27,61]D
[1B,3F,11]H [27,63,17]D
Half line feed -- Half line feed is executed.
Request I/O status(Serial I/O only)
ESC ? DC1
- Printer status is requested.
- The printer sends back the following data to the host
computer as the printer status.
MSB
6
0
LSB
0
1/0 1/0 1/0 1/0
7
0
5
0
4
0
3
2
1
Paper out or cover open
printer busy
on line alway
:1
:1
:0
:1
I/O DATA error
[67]
[68]
[69]
[70]
ESC E
ESC Y
ESC Z
ESC z
[1B,45]H
[27,69]D
Reset - The printer is initialized.
[1B, 59]H [27,89]D
[1B,5A]H [27,90]D
[1B,7A]H [27,122]D
Designate display function- Display function is set on.
Cancels display function - Display function is set off.
Self test - Self test print is executed for 1 page.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Setup options)
❏ Setup options control codes
This command is specially designed to assist you in utilizing the printer to its fullest
potential. Most of printer's setup options can be accessed and changed through the
following command sequence.
Setup command sequence
Setup command codes
1B 7C 60 m1 m2 a1...ak
header
Setup terminate codes
1B 7C 60 01 00 12h
Setup declare codes
1B 7C 60 01 00 11 h
m1,m2: Number of data bytes in
the function commands
and parameters(a1..ak).
k = (m1 + (256 x m2))
1 . This command sequence is only valid when the Software setup is set to YES (enabled) in
the extended options at the front control panel. The command is treated as regular print
data if the Software setup is disabled.
2 . Always start the software setup commands with the setup declare code and end by the setup
terminate code.
3 . Insert "46. Dont save" command before the setup terminate codes if the setup command
sequences are used frequently. Otherwise, EEPROM ERROR may occur due to exceeding the
number of the allowable write cycle of the EEPROM.
Setup command sequence
ITEM Mode
Code & Hexadecimal
n (Hex.) = selection
n: 0 = 100% n: A = 116% n: 14 = 600%
[1]
Zoom in/out
Header SI n
1B, 7C, 60, 02, 00, 0F, n
1 = 91%
2 = 83%
3 = 79%
4 = 66%
B
C
= 120%
= 141%
16 = 800%
18 = 1000%
1A = 1200%
1C = 1400%
1E = 1600%
10 = 200%
12 = 400%
n: 0 = MODE 1
1 = MODE 2
2 = MODE 3
HIGH Quality Low Speed
Normal Quality Normal SPeed
LOW Quality Hight Speed
[2]
Graphic Print
Mode
Header # n
1B, 7C, 60, 02, 00, 23, n
n: 0 = no slash "0"
[3]
[4]
[5]
[6]
Zero style
Header 0 n
1B, 7C, 60, 02, 00, 30, n
n: 1 = slashed "
Ø"
n: 0 = SIMPLE (1PASS FONT)
1 = Comp (2PASS FONT)
Accent Character Header 1 n
1B, 7C, 60, 02, 00, 31, n
n: 0 = YES (FF Code Valid)
1 = NO (FF Code invalid)
FF Code at TOF
Line spacing
Header 2 n
1B, 7C, 60, 02, 00, 32, n
n: 0 = 6 lpi
n: 2 = 9 lpi
n: 4 = 4 lpi
Header 3 n
1B, 7C, 60, 02, 00, 33, n
1 = 8 lpi
3 = 3 lpi
Note: The set-up declare codes will reset the printer to its default state.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Setup options)
ITEM Mode
Code & Hexadecimal
n (Hex.) = selection
n: 0 = CR only n: 2 = Autofeed
1 = CR + LF
Header 5 n
1B, 7C, 60, 02, 00, 35, n
[7]
CR setting
n: 0 = LF only
1 = CR + LF
Header 6 n
1B, 7C, 60, 02, 00, 36, n
[8]
LF setting
n: 0 = DETECT at any position
1 = DETECT only page end
Header 8 n
1B, 7C, 60, 02, 00, 38, n
[9]
P.out detection
n: 0 = No (Unlock)
1 = Yes (Lock)
Header > a n
1B, 7C, 60, 03, 00, 3E, 61, n
[10]
[11]
[12]
[13]
[14]
[15]
Page length
lock
n: 0 = No (Unlock)
1 = Yes (Lock)
Header > b n
1B, 7C, 60, 03, 00, 3E,62,n
Font lock
n: 0 = No (Unlock)
1 = Yes (Lock)
Header > c n
1B, 7C, 60, 03, 00, 3E, 63, n
Pitch lock
n: 0 = No (Unlock)
1 = Yes (Lock)
Header > d n
1B, 7C, 60, 03, 00, 3E, 64, n
Quality lock
Reset key lock
Page length
n: 0 = No (Unlock)
1 = Yes (Lock)
Header > e n
1B, 7C, 60, 03, 00, 3E, 65, n
(m = 0: Fanfold)
Header C m n
1B, 7C, 60, 03, 00, 43, m, n
n: 0 = 11"
1 = 2"
n: 8 = 5.5" n: 10 = 9.5" n: 18 = 13.5"
9 = 6"
11 = 10"
12 = 10.5" 1A = 14.5
13 = 11" 1B = 15"
14 = 11.5" 1C = 15.5"
15 = 12" 1D = 16"
16 = 12.5" 1E = 16.5"
17 = 13" 20 = 12"
19 = 14"
2 = 2.5"
3 = 3"
A = 6.5"
B = 7"
4 = 3.5"
5 = 4"
6 = 4.5"
7 = 5"
C = 7.5"
D = 8"
E = 8.5"
F = 9"
(m=1: Single sheets paper)
n: 0 = A4 portrait
1 = B5 portrait
2 = A4 portrait
3 = B4 portrait
4 = Letter portrait
5 = Legal portrait
6 = A3 portrait
n: 11 = B5 landscape
12 = A4 landscape
13 = B4 landscape
14 = Letter landscape
15 = Legal landscape
16 = A3 landscape
n: 0 = Epson
1 = IBM
3 = HP
Header E n
1B, 7C, 60, 02, 00, 45, n
[16]
[17]
[18]
Emulation
n: 0 = Normal
1 = Normal
n: 2 = Dark 1
3 = Dark 2
Header G n
1B, 7C, 60, 02, 00, 47, n
Multipart
n: 0 = 0 line
1 = 1 line
n: 5 = 5 lines
6 = 6 lines
n: 10 = 10 lines
Header N n
1B, 7C, 60, 02, 00, 4E, n
Bottom margin
11 = 11 lines
12 = 12 lines
13 = 13 lines
14 = 14 lines
15 = 15 lines
2 = 2 lines
3 = 3 lines
4 = 4 lines
7 = 7 lines
8 = 8 lines
9 = 10 lines
n: 0 = No
1 = Yes
Header O n
1B, 7C, 60, 02, 00, 4F, n
[19]
[20]
Override
n: 0 = 10cpi
1 = 10cpi
2 = 12cpi
n: 5 = 20cpi
6 = 24cpi
Header P n
1B, 7C, 60, 02, 00, 50, n
Character
spacing
7 = Proportional
8 = 1/2 Proportional
9 = 16.7cpi
3 = 15cpi
4 = 17.1cpi
123
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Setup options)
ITEM Mode
Code & Hexadecimal
n (Hex.) = selection
00 ≤ ml ≤ 63
00 ≤ mr ≤ 63
Left margin
Right margin
[21]
Left/right
margin
(Header) Q ml mr
1B, 7C, 60, 03, 00, 51, ml, mr
n: 0 = USA
1 = France
2 = Germany
3 = U.K
n: 5 = Sweden n: A = Denmark2
[22]
International
character
Header R n
1B, 7C, 60, 02, 00, 52, n
6 = Italy
B = Spain2
C = Latin America
D = Korea
E = Turkey
F = Legal
7 = Spain
8 = Japan
9 = Norway
4 = Denmark
n: 0 = No scroll
1 = 0.5 second
2 = 1 second
n: 3 = 5 seconds
4 = 10 seconds
5 = 15 seconds
[23]
Auto scroll
Header S n
1B, 7C, 60, 02, 00, 53, n
n: 0 = Valid at any position
1 = Valid at any TOF position
[24]
[25]
[26]
[27]
[28]
[29]
[30]
Auto scroll Valid
Position
Header S [FF] n
1B, 7C, 60, 03, 00,53, FF, n
00 ≤ n ≤ 15
Top margin
Header T [00] n
1B, 7C, 60, 03, 00, 54, 00, n
n: 0 = Pre-direction
n: 2 = Uni-direction
Print direction
Paper width
Header U n
1B, 7C, 60, 02, 00, 55, n
1 = Pre-direction
3 = Bi-direction
n: 0 = 15 inches
n: 2 = 5 inches
Header W n
1B, 7C, 60, 02, 00, 57, n
1 = 10 inches
n: 0 = Invalid
1 = Valid
IBM graphics
AGM
Header Y n
1B, 7C, 60, 02, 00, 59, n
n: 0 = No
1 = Yes
Label mode
Header [ n
1B, 7C, 60, 02, 00, 5B, n
n: 0 = 1
1 = 2
2 = 4
n: 4 = 12
Enlarged
Character Size
Header ] X n
1B, 7C, 60, 03, 00,5D, 58, n
5 = 16
6 = 24
7 = 32
3 = 8
n: 0 = MODE2
1 = Ignored
2 = MODE1
[31]
[32]
Barcode
/
Header ] m n
Enlarged character 1B, 7C, 60, 03, 00, 5D, 6D, n
command
n: 0 = INDSTRAL 2/5
1 = INTRLVD 2/5
2 = MATRIX 2/5
3 = CODABAR
4 = CODE 11
n: 7 = CODE 128
8 = EAN 8
9 = EAN 13
10 = UPC-A
11 = UPC-E
Barcode type
Header ] n n
1B, 7C, 60, 03, 00, 5D, 6E, n
5 = CODE 39
6 = CODE 93
12 = POSTNET
13 = ELEMENT
124
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Setup options)
ITEM Mode
Code & Hexadecimal
n (Hex.) = selection
n: 0 = PCL3+
1 = PCL3
n: 2 = PCL3+D
[33]
PCL Mode
Header ] w n
1B, 7C, 60, 03, 00, 3C, 65, n
n: 0 = 1
1 = 1.5
2 = 2
[34]
Bar Code Size
Header ] x n
1B, 7C, 60, 03, 00,5D, 78, n
3 = 2.5
n: 0 = Sleep Mode Valid
1 = Sleep Mode invalid
[35]
[36]
[37]
Sleep Mode
Line feed Speed
Code page
Header e n
1B, 7C, 60, 03, 00,65, n
n: 0 = Normal Speed
1 = Half Speed
Header f n
1B, 7C, 60, 03, 00,66, n
n: 0 = 437 (USA)
1 = 850 (Multi-lingual)
3 = 860 (Portuguese)
Header i n
1B, 7C, 60, 02, 00, 69, n
4 = 863 (Canadian-French)
5 = 865 (Nordic)
6 = 857 (Turkey)
20h = ISO-8859-1
7 = 858
8 = 861
9 = BRASCII
0A = ABICOMP
n: 0 = Roman
1 = Roman
2 = Sans Serif
3 = Courier
4 = Prestige
5 = Script
n: 6 = OCR-B
[38]
[39]
Font select
Header k n
1B, 7C, 60, 02, 00, 6B, n
7 = OCR-A
8 = Gothic
9 = Orator
A = Orator-S
m:0
Option
Header o m n
n: 0 = CSF not installed
1 = Single bin
2 = Double bin
1B, 7C, 60, 03, 00, 6F, m, n
n = n1 + 256 × n2
[40]
[41]
TOF
adjustment
Header p n1 n2
1B, 7C, 60, 03, 00, 70, n1, n2
n/60" (0 ≤ n ≤ 480)
Character table
Header t m n
1B, 7C, 60, 03, 00, 74, m, n
m:0 = (Epson)
n: 0 = Italic
m:1 = (IBM)
n: 0 = IBM Set 1
1 = IBM Set 2
1 = Graphic
2 = Download
3 = Code page
m:3 = (HP)(PRIMARY FONT)]
n: 0 = ROMAN-8
1 = CODE PG
2 = PC-8D/N
3 = ECMA
4 = LEGAL
(8U)
CODE PAGE
PC-8 Denmark/Norway(11U)
ECMA LATIN 1(ISO 8859-1,0N)
(HP SET,1U)
5 = SWEDEN1
6 = SWEDEN2
7 = SPAIN
8 = FRANCE
9 = GERMAN
A = U.K.
(ISO-10,0S)
(ISO-11,3S)
(ISO-17,2S)
(ISO-69,1F)
(ISO-21,1G)
(ISO-4,1E)
B = PORTU
PORTUGAL(ISO-16,4S)
(ISO-60,0D)
(ISO-61,1D)
C = NORWAY1
D = NORWAY2
E = IRV
(ISO-2,2U)
125
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Control code summary (Setup options)
ITEM Mode
Code & Hexadecimal
n (Hex.) = selection
F = ITALY
10 = FRANC2
11 = GERMN2
12 = SPAIN2
13 = SPAIN3
14 = JAPAN
15 = PORTU2
(ISO-15,0I)
FRANCE 2(ISO-25,0F)
GERMAN 2(HP SET,OG)
(ISO-85,6S)
(HP-SET,1S)
(ISO-14,0K)
PORTUGAL(ISO-84,5S)
m:4 = (HP)(SECONDARY FONT)
n: 0 = LINE-DRAW
1 = MATH-7
(0L)
(0M)
[42]
[43]
Tabulation
Header w n
1B, 7C, 60, 02, 00, 77, n
n: 0 = 2 characters
1 = 4 characters
2 = 6 characters
n: 3 = 8 characters
4 = 10 characters
5 = 12 characters
Quality
Header x n
1B, 7C, 60, 02, 00, 78, n
n: 0 = LQ
1 = Draft
2 = LQ
n: 4 = Draft
5 = Speed draft (SD)
6 = Super speed draft (SSD)
7 = HQDR
3 = NLQ
[44]
[45]
Invert display
Header y n
1B, 7C, 60, 02, 00, 79, n
n: 0 = No (normal)
1 = Yes (upside-down)
Display
language
Header z n
1B, 7C, 60, 02, 00, 7A, n
n: 0 = English
1 = Deutsch
2 = Français
n: 3 = Español
4 = Italiano
[46]
Dont save
Header [7F]
1B, 7C, 60, 01, 00, 7F
By inserting this command before the setup terminate
codes, all the setup changes are not saved in the
EEPROM but only in the current memory.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
Appendix C. Character sets
Epson, Italic character set
H
0 1 2 3 4 5 6 7 8
9 A
B C D E F
(0) (16) (32) (48) (64) (80) (96) (112)(128)(144)(160)(176)(192)(208)(224)(240)
L
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Note: This character set is selected with ESC t 0. Refer to Control code summary section.
Epson, Graphic character set, extended
H
0 1 2 3 4 5 6 7 8
9 A
B C D E F
(0) (16) (32) (48) (64) (80) (96) (112)(128)(144)(160)(176)(192)(208)(224)(240)
L
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Note: This character set is selected with ESC 6 and ESC t 1. Refer to Control code summary section.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
International character set (EPSON)
Hex
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
Country
U.S.A.
FRANCE
GERMANY
U.K.
DENMARK
SWEDEN
ITALY
SPAIN
JAPAN
NORWAY
DENMARK 2
SPAIN 2
LATIN AMERICA
KOREA
TURKEY
LEGAL
Note: This character set is selected with ESC R n in the epson mode or from the front control panel. Refer to
Control code summary or the extended setup options.
IBM character set 1
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(0) (16) (32) (48) (64) (80) (96) (112)(128) (144)(160) (176)(192)(208)(224)(240)
L
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Note: This character set is selected with ESC 7. Refer to Control code summary section.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
IBM character set 2
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(0) (16) (32) (48) (64) (80) (96) (112)(128) (144)(160) (176)(192)(208)(224)(240)
L
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Note: This character set is selected with ESC 6. Refer to Control code summary section.
IBM all character set
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(0) (16) (32) (48) (64) (80) (96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
L
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Note: This character set is selected with ESC \. Refer to Control code summary section.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
HP Mode
PC-8 (Danish / Norwegian) Character sets (PCL)
ROMAN-8 Character sets (PCL)
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
A
B
C
D
E
F
A
B
C
D
E
F
The (00)H-(1F)H and (7F)H normally function as control code.
ECMA-94 Latin 1 (ISO 8859-1)
Character sets (PCL)
LEGAL character sets (PCL)
L/H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
A
B
C
D
E
F
A
B
C
D
E
F
The character of (A0)H-(FF)H are, respectively, the same as those
of (20)H-(7F)H.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
MATH 7 character sets (PCL)
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
LINE DRAW character sets (PCL)
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
The character of (A0)H-(FF)H are, respectively, the same as those of (20)H-(7F)H.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
International character set [ISO] (PCL)
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
ISO ID
ASCII
6 0U
69 1F
- 0F
FRANCE
FRANCE2
GERMANY 21 1G
GERMANY2 - 0G
U.K.
4 1E
SWEDEN
11 0S
SWEDEN2 10 3S
ITALY
15 0I
17 2S
85 6S
SPAIN
SPAIN2
SPAIN3
JAPAN
NORWAY
-
1S
14 0K
60 0D
NORWAY2 61 1D
PORTUGAL 16 4S
PORTUGAL2 84 5S
IRV
2 2U
•The character of (A0)H-(FF)H are respectively, the same as those of (20)H-(7F)H.
•The characters with (20)H-(7F)H codes which are not shown in the International character set above are the same as those
of (20)H-(7F)H in ROMAN-8.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
Code 00H ~ 7FH (Common)
Code Page 437 (U.S.A.)
Code Page 850 (Multilingual)
Code Page 857 (Turkish)
PCL mode
The (00)H-(1F)H and (7F)H normally function as control code.
The DEL(7F)H code as " " character in PCL.
While TRANSPARENT mode is character font available. These characters are printable only while in TRANSPARENT
mode.
EPSON/IBM mode
•The (00)H-(1F)H and (80)H-(9F)H function as control codes only while in IBM character set 1 is selected.
•The (03)H-(06)H,(15)H and (80)H-(9F)H are printable only while in IBM character set 2 is selected.
•The all of the font table are printable only while in IBM all character set is selected.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
Code Page 858 (Multilingual-Euro)
Code Page 860 (Portuguese)
Code Page 861 (Icelandic)
Code Page 863 (Canadian French)
PCL mode
The (00)H-(1F)H and (7F)H normally function as control code.
The DEL(7F)H code as " " character in PCL.
While TRANSPARENT mode is character font available. These characters are printable only while in TRANSPARENT
mode.
EPSON/IBM mode
•The (00)H-(1F)H and (80)H-(9F)H function as control codes only while in IBM character set 1 is selected.
•The (03)H-(06)H,(15)H and (80)H-(9F)H are printable only while in IBM character set 2 is selected.
•The all of the font table are printable only while in IBM all character set is selected.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Character Sets
Code Page 865 (Nordic)
BRASCII
ABICOMP
ISO-1 (ISO-8859-1)
135
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Reverse control panel sheet
Appendix D. Reverse control panel sheet
LCD
❏ Installation
The reverse control panel sheet allows you to easily read the function key labels from the back
of the printer. In situations where working from the back of the printer is convenient, simply
lay the reverse control panel sheet in position over the standard control panel.
Note:
If you set the invert display mode in the extended setup options, the display messages also
become upside down orientation.
ON
LINE
ON P.OUT
POWER
LINE
TEAR
OFF
FF
RLF
LF
M.RLF
M.LF
ALT
QUALITY
SETUP
PARK
L
C
D
RESET
136
Download from Www.Somanuals.com. All Manuals Search And Download.
This unit complies with the Low Voltage Directive 73/23/EEC and the EMC Directive
89/336/EEC.
Dies Gerät entspricht den Bedingungen der Niederspannungs-Vorschrift 73/23/EEC und dem
EMVG nach 89/336/EEC.
Maschinenlärminformationsverordnung 3. GSGV, 18. 01. 1991:
Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß ISO 7779.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTER DIVISION
1-1-1, AKANEHAMA, NARASHINO-SHI, CHIBA 275-8558 JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Python GPS Receiver GPS tracking User Guide
Radica Games Board Games 73013UK User Guide
Radica Games Games 72045 User Guide
RCA Camcorder EZ4000 User Guide
RCA Car Video System DRC220N User Guide
Rockford Fosgate Stereo Amplifier 250, 360, 400, 500, 600, 800, 1000 User Guide
Samsung CD Player EV 1 User Guide
Samsung CRT Television UN40EH6000 User Guide
Samsung MP3 Player YP R1 User Guide
Senco Air Compressor PC1010 User Guide