Seagate Computer Drive ST160LT007 9ZV14D User Guide

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes will not contribute to battery

power consumption.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.2

FORMATTED CAPACITY

Formatted capacity*

Guaranteed logical blocks (LBA) - 512 emulation

Bytes per physical sector

ST320LT007 - 9ZV142

ST320LT009 - 9WC142

ST320LT014 - 9YK142

625,142,448

4096

ST250LT007 - 9ZV14C

ST250LT009 - 9WC14C

ST250LT014 - 9YK14C

488,397,168

312,581,808

ST160LT007 - 9ZV14D

ST160LT009 - 9WC14D

ST160LT014 - 9YK14D

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

2.2.1

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of

guaranteed logical blocks (LBA) as defined above.

See Section 5.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing support of

drives with capacities over 137GB.

2.3

DEFAULT LOGICAL GEOMETRY

CYLINDERS

16,383

READ/WRITE HEADS

SECTORS PER TRACK

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of

guaranteed logical blocks (LBA) as defined above.

2.4

PHYSICAL ORGANIZATION

Models

READ/WRITE HEADS

NUMBER OF DISKS

320GB models

250GB models

160GB models

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.5

RECORDING AND INTERFACE TECHNOLOGY

4K SECTOR MODELS

Interface

Serial ATA (SATA)

Recording method

Perpendicular

Recording density BPI (bits/in avg)

Track density TPI (tracks/in avg)

1397k

315k

Areal density (Gb/in avg)

425

Spindle speed (RPM) ( 0.2%)

Maximum Internal transfer rate (Mb/s)

I/O data-transfer rate (Gb/s max)

Interleave

7200

1247

3.0

1:1

Cache buffer

16 MB (16,384 KB)

2.6

PHYSICAL CHARACTERISTICS

DRIVE SPECIFICATION

Height

Width

(mm)

(in)

6.8 +/-0.2

0.268 +/-0.0079

(mm)

(in)

69.85 +/-0.25

2.75 +/-0.0098

Length

(mm)

(in)

100.35 +0.20/-0.25

3.951 +0.008/-0.010

Weight (max)

All models

92.0 g

0.203 lb

2.7

SEEK TIME

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The

specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead.

Table 2 Typical seek times

TYPICAL SEEK TIMES (MS)

Track-to-track

READ

1.5

Average

Average latency

4.17

These drives are designed to consistently meet the seek times represented in this manual. Physical

seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values.

However, due to the manner in which these drives are formatted, benchmark tests that include

command overhead or measure logical seeks may produce results that vary from these specifications.

NOTE

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.8

START/STOP TIMES

TIME TO READY

TYPICAL

3.5

MAX @ 25°C

Power-on to Ready (sec)

Standby to Ready (sec)

4.0

3.0

2.9

POWER SPECIFICATIONS

The drive receives DC power (+5V) through a native SATA power connector.

2.9.1

Power consumption

Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested,

under nominal conditions, at 25°C ambient temperature. These power measurements are done with Interface Power Management modes

like HIPM and DIPM enabled.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does not execute a read or write

operation. Servo electronics are active. Seek mode power is measured based on three random seek operations every 100ms. This mode

is not typical.

• Read/write power and current

Read/write power is measured with the heads on track, based on three 63 sector read or write operations every 100ms.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-

down model

Table 3 DC power

POWER DISSIPATION

Spinup (max)

Seek

+5V INPUT AVERAGE (25° C)

1.00A

1.6W

Read

1.6W

Write

1.9W

Idle, performance*

Idle, active*

Idle, low power mode*

Standby**

1.3W

0.90W

0.66W

0.15W

Sleep

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

**Standby power is measured at steady state (after 200ms from transition)

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.9.1.1

Typical current profile

Figure 1. Typical +5V only startup and operation current profile

2.9.2

Deferred spinup

Momentus Thin drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade

Server family of drives.

2.9.3

Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line.

Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10

MHz.

Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.

NOTE

2.9.4

Voltage tolerance

Voltage tolerance (including noise):

5V ± 10%

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.9.5

Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power

management through the system setup program. The drive features the following power-management modes:

Table 4 Power management modes

POWER MODES

Active (operating)

Idle, performance

Idle, active

HEADS

Tracking

Floating

Parked

SPINDLE

Rotating

Stopped

BUFFER

Full power

Self refresh—low power

Idle, low power

Standby

Sleep

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby timer, the drive can

also enter Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is

established using a Standby or Idle command. In Standby mode, the drive buffer is in Self Refresh Low Power mode, the heads are

parked and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disk access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is in Self Refresh Low

Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset

from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down

from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transi-

tion to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disk access is

necessary.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.10 ENVIRONMENTAL SPECIFICATIONS

2.10.1 Ambient temperature

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.

Operating:

0° to 60°C (32° to 140°F)

Nonoperating:

–40° to 70°C (–40° to 158°F)

2.10.2 Temperature gradient

Operating

20°C per hour (68°F per hour max), without condensation

35°C per hour (95°F per hour max), without condensation

Nonoperating

The recommended storage period:

• 1 year under controlled conditions of 34°C 90%RH or less

• 90 days in uncontrolled storage conditions

NOTE

2.10.3 Humidity

2.10.3.1 Relative humidity

Operating

5% to 95% noncondensing (30% per hour max)

Nonoperating

2.10.3.2 Wet bulb temperature

Operating

37.7°C (99.86°F max)

Nonoperating

40°C (104°F max)

2.10.4 Altitude

Operating

–304.8 m to 3,048 m (–1000 ft to 10,000+ ft)

–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)

Nonoperating

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.10.5 Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may

be applied in the X, Y or Z axis.

2.10.5.1 Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs

based on half-sine shock pulses of 2ms. Shocks should not be repeated more than two times per second.

2.10.5.2 Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when

subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2ms duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when

subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock pulse of 1ms duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when

subsequently put into operation is 600 Gs based on a nonrepetitive half-sine shock pulse of 0.5ms duration.

2.10.6 Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws.

Vibration may be applied in the X, Y or Z axis.

2.10.6.1 Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are

specified below.

5–500 Hz

1.0 Gs (0 to peak). Max displacement may apply below 10Hz.

2.10.6.2 Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in

performance when subsequently put into operation are specified below.

5–500 Hz:

5.0 Gs (0 to peak). Max displacement may apply below 22Hz.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.11 ACOUSTICS

Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is conducted at room

temperature (approximately 25°C). Emission levels are reported as the total A-weighted sound power levels for steady state, idle, and

active seek modes of operation.

Table 5 Drive A-weighted Sound Power Levels (SWL, BA)

IDLE*

PERFORMANCE SEEK

2.3 bels (typ)

2.5 bels (max)

2.5 bels (typ)

2.7 bels (max)

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Test for Prominent Discrete Tones (PDTs)

Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the

absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the

inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards.

*Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies.

2.12 ELECTROMAGNETIC IMMUNITY

When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected

to the radio frequency (RF) environments defined in the following table:

Table 6 Radio frequency environments

PERFORMANC REFERENCE

TEST

DESCRIPTION

E LEVEL

STANDARD

Electrostatic discharge

Radiated RF immunity

Contact, HCP, VCP: 4 kV; Air: 8 kV

EN 61000-4-2: 95

80 to 2000 MHz, 10 V/m,

80% AM with 1 kHz sine

900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz

EN 61000-4-3: 96

ENV 50204: 95

Electrical fast transient

Surge immunity

1 kV on AC mains, 0.5 kV on external I/O

1 kV differential, 2 kV common, AC mains

EN 61000-4-4: 95

EN 61000-4-5: 95

EN 61000-4-6: 97

Conducted RF immunity

150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz

sine

Power Frequency H-field

immunity

1 A/m, 50Hz/60Hz, 3 axes

EN 61000-4-8: 97

EN 61000-4-11: 94

Voltage dips, interrupts

30% Reduction for 25 cycles

>95% Reduction for 250 cycles

>95%, 0.5 cycles

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.13 RELIABILITY

MEASUREMENT TYPE

SPECIFICATION

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Load/Unload (U/UL)

1 per 10 bits read, max

<0.48%

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

32°C, 80% relative humidity

5°C, 80% relative humidity

5°C, 10% relative humidity

55°C, 16% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

To determine the warranty for a specific drive, use a web browser to access the

following web page:

Warranty

http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance

You will be asked to provide the drive serial number, model number (or part number) and coun-

try of purchase. After submitting this information, the system will display the warranty informa-

tion for your drive.

2.14 AGENCY CERTIFICATION

2.14.1 Safety certification

These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.

2.14.2 Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic

Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are

defined by EN 55024.

Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the

test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly

designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and

system integrators should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the

Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the

Radio Research Laboratory (RRL) Communications Commission, Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B

products. Drives are tested in a representative, end-user system by a Korean-recognized lab.

• Certificate number:STX-MomentusThin (B)

• Trade name or applicant:Seagate Technology LLC

• Certificate date:

May 14, 2010

• Manufacturer/nationality:USA, Singapore and China

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the

Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).

2.14.3 FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As

such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal

Communications Commission verification or certification of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive,

motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC

rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict

accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television,

which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective

measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find

helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television

Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington,

DC 20402. Refer to publication number 004-000-00345-4.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

2.15 ENVIRONMENTAL PROTECTION

Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical

substances.

2.15.1 European Union Restriction of Hazardous Substances (RoHS)

The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including

Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is

manufactured with components and materials that comply with the RoHS Directive.

2.15.2 China Restriction of Hazardous Substances (RoHS) Directive

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information

mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products"

Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined

by the China RoHS MCV Standard.

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by

the China RoHS MCV Standard.

2.16 CORROSIVE ENVIRONMENT

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments

containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot

duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic

drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate

products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging.

In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly

(PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber,

that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by

replacing materials near circuitry with sulfide-free alternatives.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

3.0 CONFIGURING AND MOUNTING THE DRIVE

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

HANDLING AND STATIC-DISCHARGE PRECAUTIONS

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.

Observe the following standard handling and static-discharge precautions:

•

Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD.

Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer

that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•

Handle the drive only by its edges or frame.

The drive is fragile—handle it with care. Do not press down on the drive top cover.

Always rest the drive on a padded, antistatic surface until you mount it in the computer.

Do not touch the connector pins or the printed circuit board.

CAUTION

Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some

factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2

CONFIGURING THE DRIVE

Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/

slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA

host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This means both

drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation. It is normally not necessary to set any jumpers on this drive for proper operation. If

the host system does not support SATA 3Gb/s operation, place a jumper on pins 1 and 2 to limit the drive to 1.5Gb/s operation.

3.0 Gbits per second operation

Limit data transfer rate to

1.5 Gbits per second

Jumper block

SATA power connector

SATA interface connector

Figure 2. Serial ATA connectors

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

3.3

SERIAL ATA CABLES AND CONNECTORS

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be

30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 7 for connector pin definitions. Either end of the SATA

signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle

incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 3.

SATA interface connector

Power connector

SATA interface cable

Power cable

Figure 3. Attaching SATA cabling

Each connector is keyed to ensure correct orientation.

3.4

DRIVE MOUNTING

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure Figure 4.

for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:

• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

• Use only M3 x 0.5 mounting screws.

• Do not overtighten the mounting screws. Maximum torque: 4.0 in-lb (0.4519 N-m).

• Four (4) threads (0.080 inches, 2.032 mm) minimum screw engagement recommended.

• Avoid excessive drive distortion when mounting. Refer to the following specifications for stiffness/deflection information:

TOP COVER STIFFNESS/DEFLECTION

Operating with no performance degradation, emitted noise,

mechanical damage, or hard errors

10 mm probe: 1.02kgf or

5 mm probe: 0.92kgf

Non-operating with no hard errors

20 mm probe: 2kgf at any point of top cover

20 mm probe: 15kgf at top cover edges only

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Measurements shown in Figures 4 and 5 are inches and (mm).

Figure 4. Mounting dimensions (for FIPS 140-2 models) — top, side and end view

FIPS 140-2 Models Contain 3 Tamper Evident Stickers with the marking "Tamper Indicator - Do

Not Remove". These stickers must remain attached to provide the tamper evidence throughout the

life of the drive. Removing these stickers will indicate tampering and void the drive warranty.

WARNING

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 5. Mounting dimensions (for standard models) — top, side and end view

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

4.0 ABOUT FIPS

The Federal Information Processing Standard (FIPS) Publication 140-2, FIPS PUB 140-2, is a U.S. government computer security

standard used to accredit cryptographic modules. It is titled “Security Requirements for Cryptographic Modules”. The initial publication

was on May 25, 2001 and was last updated December 3, 2002.

Purpose

The National Institute of Standards and Technology (NIST) issued the FIPS 140 Publication Series to coordinate the requirements and

standards for cryptography modules that include both hardware and software components.

Federal Information Processing Standard (FIPS) 140-2 Level 2 Certification requires drives to go through government agencies

certifications to add requirements for physical tamper-evidence and role-based authentication.

Level 2 security

Level 2 improves upon the physical security mechanisms of a Level 1 (lowest level of security) cryptographic module by requiring

features that show evidence of tampering, including tamper-evident coatings or seals that must be broken to attain physical access to the

plaintext cryptographic keys and critical security parameters (CSPs) within the module, or pick-resistant locks on covers or doors to

protect against unauthorized physical access.

Figure 6. Example of FIPS tamper evidence labels.

May not represent actual drive.

NOTE

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

5.0 SERIAL ATA (SATA) INTERFACE

These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output

(PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to

provide reliable high-speed data transfers.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification.

5.1

HOT-PLUG COMPATIBILITY

Momentus Thin drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed

Serialized AT Attachment specification revision 2.0. This specification can be downloaded from http://www.serialata.org. This device

requires a COMRESET from the host after a hotplug event.

5.2

SERIAL ATA DEVICE PLUG CONNECTOR PIN DEFINITIONS

Table 7 summarizes the signals on the Serial ATA interface and power connectors.

Table 7 Serial ATA connector pin definitions

Segment Pin

Function

Ground

A+

Definition

Signal

2nd mate

Differential signal pair A from Phy

A-

Ground

2nd mate

Differential signal pair B from Phy

B-

B+

Ground

2nd mate

Key and spacing separate signal and power segments

Power

P10

P11

3.3V power

3.3V power, pre-charge, 2nd mate

1st mate

V₃₃

Ground

V₅

2nd mate

5V power, pre-charge, 2nd mate

5V power

Ground

2nd mate

Reserved

The pin corresponding to P11 in the backplane receptacle connector is also reserved

The corresponding pin to be mated with P11 in the power cable receptacle connector

shall always be grounded

P12

P13

P14

P15

Ground

V₁₂

1st mate.

12V power, pre-charge, 2nd mate

12V power

V₁₂

1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2. The comments on the mating sequence apply to the case of backplane blindmate connector only.

In this case, the mating sequences are:

• the ground pins P4 and P12.

• the pre-charge power pins and the other ground pins.

• the signal pins and the rest of the power pins.

NOTE

3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge

when installed in a blind-mate backplane configuration.

4. All used voltage pins (V_x) must be terminated.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

5.3

SUPPORTED ATA COMMANDS

The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to

the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 30.for details and

subcommands used in the S.M.A.R.T. implementation.

COMMAND NAME

COMMAND CODE (IN HEX)

ATA-STANDARD COMMANDS

Device Configuration Restore

Device Configuration Freeze Lock

Device Configuration Identify

Device Configuration Set

Download Microcode

Execute Device Diagnostics

Flush Cache

B1h/C0h

B1h/C1h

B1h/C2h

B1h/C3h

92h

90h

E7h

Flush Cache Extended

Identify Device

EAh

ECh

91h

Initialize Device Parameters

Read Buffer

E4h

Read DMA

C8h

Read DMA Extended

Read DMA without Retries

Read Long with Retries

Read Long without Retries

Read Multiple

25h

C9h

22h

23h

C4h

Read Multiple Extended

Read Native Max Address

Read Native Max Address Extended

Read Sectors

29h

F8h

27h

20h

Read Sectors Extended

Read Sectors without Retries

Read Verify Sectors

24h

21h

40h

Read Verify Sectors Extended

Read Verify Sectors without Retries

Seek

42h

41h

70h

Set Features

EFh

Set Max Address

F9h

Note: Individual Set Max commands are identi-

fied by the value placed in the Set Max Fea-

tures register as defined to the right.

Address:

Password:

Lock:

Unlock:

Freeze Lock:

Set Multiple Mode

C6h

S.M.A.R.T. Disable Operations

B0h/D9h

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMAND NAME

COMMAND CODE (IN HEX)

B0h/D2h

B0h/D8h

B0h/DBh

B0h/E0h

B0h/D4h

B0h/D1h

B0h/D0h

B0h/D5h

B0h/DAh

B0h/D3h

B0h/D7h

B0h/E1h

B0h/D6h

E8h

S.M.A.R.T. Enable/Disable Autosave

S.M.A.R.T. Enable Operations

S.M.A.R.T. Enable/Disable Auto Offline

S.M.A.R.T. Enable One Attribute Modification

S.M.A.R.T. Execute Offline

S.M.A.R.T. Read Attribute Thresholds

S.M.A.R.T. Read Data

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Return Status

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Write Attribute Thresholds

S.M.A.R.T. Write Attribute Values

S.M.A.R.T. Write Log Sector

Write Buffer

Write DMA

CAh

Write DMA Extended

35h

Write DMA without Retries

Write Long with Retries

CBh

32h

Write Long without Retries

Write Multiple

33h

C5h

Write Multiple Extended

39h

Write Sectors

30h 31h

Write Sectors Extended

34h

45h

Write Uncorrectable

ATA-STANDARD POWER-MANAGEMENT COMMANDS

Check Power Mode

Idle

E5h

E3h

E1h

E6h

E2h

E0h

Idle Immediate

Sleep

Standby

Standby Immediate

ATA-STANDARD SECURITY COMMANDS

Security Set Password

Security Unlock

F1h

F2h

F3h

F4h

F5h

F6h

Security Erase Prepare

Security Erase Unit

Security Freeze Lock

Security Disable Password

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

5.3.1

Identify Device command

The Identify Device command (command code EC ) transfers information about the drive to the host following power up. The data is

organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All reserved bits or words should be set

to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.

The following commands contain drive-specific features that may not be included in the Serial ATA specification.

WORD

DESCRIPTION

VALUE

0C5A

Configuration information:

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

Number of logical cylinders

16,383

ATA-reserved

0000

Number of logical heads

Retired

0000

Retired

Number of logical sectors per logical track: 63

Retired

003F

7–9

10–19

0000

Serial number: (20 ASCII characters, 0000 = none)

ASCII

Retired

Obsolete

0000

0400

0000

x.xx

23–26

Firmware revision (8 ASCII character string, padded with

blanks to end of string)

27–46

Drive model number: (40 ASCII characters, padded with

blanks to end of string)

ST320LT007 - 9ZV142

ST320LT009 - 9WC142

ST320LT014 - 9YK142

ST250LT007 - 9ZV14C

ST250LT009 - 9WC14C

ST250LT014 - 9YK14C

ST160LT007 - 9ZV14D

ST160LT009 - 9WC14D

ST160LT014 - 9YK14D

(Bits 7–0) Maximum sectors per interrupt on Read multiple

and Write multiple (16)

8010

Reserved

0000

Standard Standby timer, IORDY supported and may be dis-

abled

2F00

ATA-reserved

0000

0200

0007

PIO data-transfer cycle timing mode

Retired

Words 54–58, 64–70 and 88 are valid

Number of current logical cylinders

Number of current logical heads

Number of current logical sectors per logical track

Current capacity in sectors

xxxx

57–58

Number of sectors transferred during a Read Multiple or

Write Multiple command

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

WORD

DESCRIPTION

VALUE

60–61

Total number of user-addressable sectors

ST320LT007 = 0FFFFFFFh

ST320LT009 = 0FFFFFFFh

ST320LT014 = 0FFFFFFFh

ST250LT007 = 0FFFFFFFh

ST250LT009 = 0FFFFFFFh

ST250LT014 = 0FFFFFFFh

ST160LT007 = 0FFFFFFFh

ST160LT009 = 0FFFFFFFh

ST160LT014 = 0FFFFFFFh

This field contains a value that is one greater than the total

number of user-addressable sectors. The maximum value

that shall be placed in this field is 0FFFFFFFh. The

0FFFFFFFh value applies to all capacities over 137GB (see

Section 2.2 and 2.3 for related information).

Retired

0000

Multiword DMA active and modes supported

(see note following this table)

xx07

Advanced PIO modes supported (modes 3 and 4 supported)

0003

0078

Minimum multiword DMA transfer cycle time per word

(120 nsec)

Recommended multiword DMA transfer cycle time per word

(120 nsec)

0078

Minimum PIO cycle time without IORDY flow control

(120 nsec)

69–74

Minimum PIO cycle time with IORDY flow control (120 nsec)

ATA-reserved

0078

0000

Queue depth

001F

0F06

Serial ATA capabilities

ATA-reserved

0000

0048

0040

Serial ATA features supported

Serial ATA features enabled

Major version number

01F0

Minor version number

0029

Command sets supported

Command sets support extension

Command sets enabled

Command sets enable extension

746B

7D09

61E3

7469

0001

61E3

Ultra DMA support and current mode

(see note following this table)

xx7F

Security erase time

0000

Enhanced security erase time

Master password revision code

FFFE

Hardware reset value

(see description following this table)

xxxx

Auto acoustic management setting

ATA-reserved

xxxx

95–99

0000

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

WORD

DESCRIPTION

VALUE

100–

103

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

These words are required for drives that support the 48-bit

addressing feature. Maximum value: 0000FFFFFFFFFFFFh.

ST320LT007 = 625,142,448

ST320LT009 = 625,142,448

ST320LT014 = 625,142,448

ST250LT007 = 488,397,168

ST250LT009 = 488,397,168

ST250LT014 = 488,397,168

ST160LT007 = 312,581,808

ST160LT009 = 312,581,808

ST160LT014 = 312,581,808

104–

118

ATA-reserved

0000

119

Free Fall Protection support (bit 5)

Free Fall Protection enable/disable (bit 5)

ATA reserved

1 = Free Fall Protection supported

0 = Free Fall Protection not supported

120

1 = Free Fall Protection feature is enabled

0 = Free Fall Protection feature is disabled

121–

127

0000

128

Security status

0021

129–

159

Seagate-reserved

xxxx

160–

254

ATA-reserved

Integrity word

0000

xxA5

255

See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:

NOTE

Description (if bit is set to 1)

BIT

WORD 63

Multiword DMA mode 0 is supported.

Multiword DMA mode 1 is supported.

Multiword DMA mode 2 is supported.

Multiword DMA mode 0 is currently active.

Multiword DMA mode 1 is currently active.

Multiword DMA mode 2 is currently active.

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

BIT

WORD 88

Ultra DMA mode 0 is supported.

Ultra DMA mode 1 is supported.

Ultra DMA mode 2 is supported.

Ultra DMA mode 3 is supported.

Ultra DMA mode 4 is supported.

Ultra DMA mode 5 is supported

Ultra DMA mode 6 is supported

Ultra DMA mode 0 is currently active.

Ultra DMA mode 1 is currently active.

Ultra DMA mode 2 is currently active.

Ultra DMA mode 3 is currently active.

Ultra DMA mode 4 is currently active.

Ultra DMA mode 5 is currently active.

Ultra DMA mode 6 is currently active.

WORD 93

BIT

1 = 80-conductor cable detected, CBLID above VIH

0 = 40-conductor cable detected, CBLID below VIL

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

5.3.2

Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets

BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a

feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.

The acceptable values for the Features register are defined as follows:

Table 8 Set Features command values

Enable write cache (default).

Set transfer mode (based on value in Sector Count register).

Sector Count register values:

00 Set PIO mode to default (PIO mode 2).

01 Set PIO mode to default and disable IORDY (PIO mode 2).

08 PIO mode 0

09 PIO mode 1

0A PIO mode 2

0B PIO mode 3

0C PIO mode 4 (default)

20 Multiword DMA mode 0

21 Multiword DMA mode 1

22 Multiword DMA mode 2

40 Ultra DMA mode 0

41 Ultra DMA mode 1

42 Ultra DMA mode 2

43 Ultra DMA mode 3

44 Ultra DMA mode 4

45 Ultra DMA mode 5

46 Ultra DMA mode 6

Disable read look-ahead (read cache) feature.

Disable write cache

Enable read look-ahead (read cache) feature (default).

Disable the Free Fall Protection feature (41 above enables the Free Fall Protection feature)

Report full capacity available

At power-on, or after a hardware or software reset, the default values of the features are as indicated above.

NOTE

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

5.3.3

S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive

attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status

report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For

more information on S.M.A.R.T. commands and implementation, see the Draft ATA-8 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that eliminates unnecessary drive

returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to

enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 9 S.M.A.R.T. commands

CODE IN FEATURES

S.M.A.R.T. COMMAND

S.M.A.R.T. Read Data

Vendor-specific

S.M.A.R.T. Enable/Disable Attribute Autosave

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Execute Off-line Immediate (runs DST)

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Write Log Sector

Vendor-specific

S.M.A.R.T. Enable Operations

S.M.A.R.T. Disable Operations

S.M.A.R.T. Return Status

If an appropriate code is not written to the Features Register, the

command is aborted and 0x04 (abort) is written to the Error register.

NOTE

MOMENTUS THIN PRODUCT MANUAL, GEN-2 REV. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

data-transfer rates 2

DC power 8

ACA 15

Default logical geometry 6

density 4

acoustics 5, 13

Active mode 10

Address 2 3

AFR 1 4

Device Configuration Freeze Lock 2 3

Device Configuration Restore 2 3

Device Configuration Set 2 3

Diagnostics 2 3

Agency certification 1 4

dimensions 1 9, 2 0

Disks 4

Altitude 11

Altitude, nonoperating 4

dissipation 8

Altitude, operating 4

Download Microcode 2 3

Ambient temperature 4, 11

ambient temperature 7

Annualized Failure Rate 1 4

Annualized Failure Rate (AFR) 5

Areal density 4, 7

Electrical fast transient 13

Electromagnetic compatibility 1 4

Electromagnetic Compatibility (EMC) 1 4

Electromagnetic Compatibility control Regulation 1 4

Electromagnetic Compatibility Directive (2004/108/

EC) 1 4

ATA commands 2 3

ATA data-transfer modes supported 4

Australia/New Zealand Standard AS/NZ CISPR22 15

Australian Communication Authority (ACA) 15

Australian C-Tick 15

Electromagnetic immunity 13

Electrostatic discharge 13

electrostatic discharge (ESD) 1 7

EN 55022, Class B 1 4

Average seek time 7

Average seek, read 4

EN 55024 1 4

bels 5

EN60950 1 4

Environmental protection 1 6

Environmental specifications 11

error-correction algorithms 2

errors 5, 1 4

BPI 4

buffer 4, 7

Bytes per physical sector 4, 6

ESD 1 7

EU 1 4

European Union (EU) requirements 1 4

European Union Restriction of Hazardous Substanc-

es 1 6

cables and connectors 1 8

Cache 4

cache 7

evice Configuration Identify 2 3

Execute Device Diagnostics 2 3

capacity 6

CE mark 1 4

certification 1 4

Check Power Mode 24

chemical substances 1 6

China RoHS directive 1 6

Class B computing device 15

compatibility 1 4

Conducted noise 9

Conducted RF immunity 13

Configuring the drive 1 7

connectors 1 8

FCC verification 15

features 2

Federal Communications Commission 15

Federal Information Processing Standard 2 1

FIPS 2 1

Flush Cache 2 3

Flush Cache Extended 2 3

Formatted capacity 4, 6

Freeze Lock 2 3

CSA60950-1 1 4

current 4

cycles 1 4

Cylinders 6

geometry 6

gradient 4

Momentus Thin Product Manual, Gen-2 Rev. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Guaranteed lba 4, 6

guaranteed sectors 6

National Institute of Standards and Technology 2 1

NIST 2 1

noise 9

handling 1 7

Handling precautions 1 7

heads 6

nominal power 7

Nonoperating shock 1 2

Nonoperating vibration 1 2

Nonrecoverable read errors 5

nonrecoverable read errors 1 4

Height 4

height 7

Humidity 11

humidity 4

Operating shock 1 2

Operating vibration 1 2

I/O data-transfer rate 4, 7

Identify 2 3

Identify Device 2 3

Physical characteristics 7

Physical organization 6

Physical read/write heads 4

point-to-point 3, 1 7

Identify Device command 2 5

Idle 8, 24

Idle and Standby timers 10

Idle Immediate 24

Power consumption 8

power dissipation 8

Idle mode 4, 10

Idle mode power 8

Information Technology Equipment (ITE) 1 4

Initialize Device Parameters 2 3

Input noise ripple 9

Interface 7

power management 10

power on/off cycles 1 4

Power specifications 8

Power-management modes 10

Power-on to Ready 8

interface 22

Power-on to ready 4

Interleave 7

precautions 1 7, 1 8

Internal data transfer rate 4

Internal data-transfer rate 7

ITE 1 4

programmable power management 10

quick reference 4

KCC 1 4

Korean Communications Commission 1 4

Korean RRL 1 4

Radiated RF immunity 13

Radio and television interference 15

radio frequency (RF) 13

random track location 8

Read Buffer 2 3

latency 4

LBA mode 6

Length 4

Read DMA 2 3

Read DMA Extended 2 3

Read DMA without Retries 2 3

read errors 5, 1 4

length 7

Load/Unload 1 4

logical geometry 6

Read Long with Retries 2 3

Read Long without Retries 2 3

Read Multiple 2 3

Max Address 2 3

Read Multiple Extended 2 3

Read Native Max Address 2 3

Read Native Max Address Extended 2 3

Read Sectors 2 3

maximum temperature 11

Microcode 2 3

mounting 1 8

mounting screws 1 2

mounting the drive 1 7

Read Sectors Extended 2 3

Read Sectors without Retries 2 3

Read Verify Sectors 2 3

Momentus Thin Product Manual, Gen-2 Rev. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Read Verify Sectors Extended 2 3

Read Verify Sectors without Retries 2 3

Read/write heads 6

Read/write power 4

read/write power and current 8

Recording density 4, 7

Recording method 7

Recording technology 7

Relative humidity 4, 11

Reliability 1 4

Standby 8, 24

Standby Immediate 24

Standby mode 4, 8, 10

Standby to Ready 8

Standby to ready 4

Start/stop times 8

Startup current 4

static-discharge 1 7

Surge immunity 13

resistance 9

Retries 2 3

tamper evident stickers 1 9

temperature 4, 7, 11

Temperature gradient 4, 11

timers 10

RF 13

RoHS 1 6

RPM 4

RRL 1 4

TPI 4

Track density 4, 7

Track-to-track seek time 4, 7

S.M.A.R.T. 24

S.M.A.R.T. implementation 2 3

Safety certification 1 4

SATA 7, 22

UL60950-1 1 4

screws 1 2, 1 8

Seagate Technology Support Services 1

sector 6

Vibration 1 2

Sectors per track 6

Security Disable Password 24

Security Erase Prepare 24

Security Erase Unit 24

Security Freeze Lock 24

Security Set Password 24

Security Unlock 24

Seek 2 3

Vibration, nonoperating 5

Vibration, operating 5

Voltage dips, interrupts 13

Voltage tolerance 4, 9

Warranty 1 4

Weight 4

seek mode 8

weight 7

Seek time 7

Wet bulb temperature 4, 11

Width 4

seek time 4

Seeking 8

width 7

Self refresh, low power 10

Serial ATA 7

Write Buffer 24

Write DMA 24

Serial ATA (SATA) interface 22

servo electronics 8

Set Features 2 3

Write DMA Extended 24

Write Long with Retries 24

Write Long without Retries 24

Write Multiple 24

Write Sectors 24

Write Sectors Extended 24

write uncorrectable 24

Set Max Address 2 3

Set Multiple Mode 2 3

Shock 1 2

Shock, nonoperating 5

Shock, operating 5

single-track seeks 7

Sleep 8, 24

Sleep mode 4, 10

sound power 5

Specification summary table 4

Spindle speed 4, 7

Spinup 8

spinup power 8

Momentus Thin Product Manual, Gen-2 Rev. G

Download from Www.Somanuals.com. All Manuals Search And Download.

Seagate Technology LLC

AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000

ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888

EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00

Publication Number: 100625253, Rev. G

November 2012

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Musical Instrument Amplifier PPG460A User Guide
Raypak Swimming Pool Heater 183A User Guide
Rotel Turntable RP 900 User Guide
Ryobi Trimmer 767r User Guide
Samsung All in One Printer Msys 835P User Guide
Samsung Washer H1245A H1290A User Guide
Sanus Systems Flat Panel Television VF2012 B1 User Guide
Sanyo Security Camera VCC XZ200P User Guide
Scag Power Equipment Lawn Mower STT 25CH LP User Guide
Sears Drill 11321308 User Guide