Identifying Codes
FCC Compliance
Controlling Volume
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
To Program for Volume Control
You can program the remote control to
control the volume and mute functions
through the EXPLORER 2000 DHCT, or
through your TV. The default is
through the TV.
To Identify Programmed Codes
You can find out which code you used to
program your TV or VCR. You can
determine the code by counting the
number of times the LED blinks during the
following procedure.
Note: This equipment has been tested and found
to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment gener-
ates, uses, and can radiate radio frequency
energy and, if not installed and used in accor-
dance with the instructions, may cause harmful
interference to radio communication. However,
there is no guarantee that interference will not
occur in a particular installation If this equip-
ment does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the use is
encourage to try to correct the interference by
one or more of the following measures:
Model ER1
Remote Control
User’s Guide
1. Point the remote control away from
the EXPLORER 2000 DHCT, the TV,
and the VCR.
1. Point the remote control away from the
EXPLORER 2000 DHCT , the TV, and
the VCR.
2. Press and hold the CBL key and the
SELECT key at the same time, until
the LED on the remote control
blinks twice.
2. Do one of the following:
•
To identify the TV code, press and
hold the TV key and the SELECT
key at the same time until the LED
on the remote control blinks twice,
or
3. Using the remote control keypad,
enter 993. The LED on the remote
blinks twice.
•
To identify the VCR code, press and
hold the VCR key and the SELECT
key at the same time until the LED
on the remote control blinks twice.
4. Press the TV key or the CBL key,
depending on which device you
want to control the volume. The
LED on the remote control blinks
twice to confirm a valid selection.
POWER
TV
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and the receiver.
3. Using the remote control keypad, enter
990. The LED on the remote blinks
twice.
•
•
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
I
SELECT
5. Point the remote toward the device
on which you chose to control the
volume, and adjust the volume to
confirm operation.
4. Press 1 on the keypad; then, count the
LED blinks. The number of blinks
indicates the first number in the code.
For example, 4 blinks indicates the first
number in the code is 4. If the LED
does not blink, the digit is 0 (zero).
Any changes or modifications not expressly
approved by Scientific-Atlanta could void the
user’s authority to operate this equipment.
A
B
2
5
8
0
C
Record of Codes
1
3
6
Record your setup codes
in the following table.
5. Press 2 on the keypad; then, count the
LED blinks. The number of blinks
indicates the second number in the
code.
4
7
9
A
United States: Scientific-Atlanta, Inc.
4261 Communications Drive, P.O. Box 6850,
Norcross, GA 30091-6850
Tel: 770.903.5000 TWX: 810.799.4912 Telex: 0542898
Europe: Scientific-Atlanta Western Europe Limited,
Home Park Estate, Kings Langley, Herts WD4 8LZ,
England Tel: +44.1.923.266133 Fax: +44.1.923.269018
Asia-Pacific: Scientific-Atlanta (HK), Ltd. Suite 56-57,
5/ F New Henry House, 10 Ice House Street, Central,
Hong Kong Tel: 852.2522.5059 Fax: 852.2522.5624
TV
6. Press 3 on the keypad; then, count the
LED blinks. The number of blinks
VCR
CBL
indicates the third number in the code.
C
7. Write down the code in the table
provided for future reference.
O
© 2000 Scientific-Atlanta, Inc.
All rights reserved.
Printed in USA January 2000 Part Number 716360 Rev D
ER1 Remote Control Quick Reference
Power
Channels
Screens
27
DHCT on or off
VCR on or off
Displays channel
Pages Up/Pages Down
1
2
3
26
information
25
24
1
2
Selects channels, up or
down
6
25
Hides interactive screen
4
Enter channel numbers
8
TV on or off
LED
Makes on-screen
decisions
7
(also used to enter your
26
27
23
3
personal identification
number [PIN] for
parental control)
Displays interactive
program guide
24
22
21
20
4
5
6
7
Sound
Views favorite channels
Displays DHCT settings
9
23
5
Mutes sound
22
Returns to last channel
viewed
19
Moves through interactive
screen choices
Adjusts volume
20
VCR/VOD
8
Chooses interactive
screen item
21
Fast forwards VCR/VOD
10
Device Control
Notes:
Records VCR program
19
18
17
9
11
Switches control between
your VCR and Video On
Demand (VOD) program
•
Program the remote control
13
10
11
before you use the DHCT. See
Programming the Remote
Control for programming
procedures.
Stops VCR/VOD
12
Rewinds VCR/VOD
Controls your VCR’s
TV/VCR function.
18
14
15
16
15
12
13
14
Plays VCR/VOD
16
•
Make sure you use only alkaline
batteries in the remote control. See
Inserting the Batteries for more
information.
Controls the BYPASS
option (See Optional
Bypass Feature)
Pauses VCR/VOD
17
T8101
Inserting the Batteries
1. Press forward then lift up on the lever
on the back cover of the remote control.
The battery cover releases, and you can
pull the cover up to remove it.
2. Remove and safely dispose of the old
batteries.
3. Insert and firmly seat two new AA
batteries (alkaline required) into the
battery compartment.
Procedure
Your remote control requires two AA
alkaline batteries.
4. Slide the front of the battery cover back
onto the remote control and snap
the back of the cover into place.
CAUTION:
Make sure you correctly align
the positive (+) and negative (-)
terminals on the batteries to the
corresponding terminals in the
remote control.
T6435
T6434
T6436
Download from Www.Somanuals.com. All Manuals Search And Download.
|