Printer Unit Type40
RCP40
Operating Instructions
Printer Reference 1
Getting Started
Installing the Printer Driver and Software
Basic Printing
For safe and correct use of this machine, please be sure to read the Safety Information in the
Operating Instructions that comes with the machine before you use it.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manuals for This Machine
The following manuals describe the operational procedures and maintenance of
this machine.
To enhance safe and efficient operation of this machine, all users should read
and follow the instructions carefully.
❖ Printer Reference 1 (this manual)
Describes the system settings, procedures and functions for using this ma-
chine. This manual is also included as a PDF file on the CD-ROM labeled
“Printer Drivers and Utilities”.
❖ Printer Reference 2
Describes the procedures and provides necessary information about using
this machine. This manual is included as a PDF file on the CD-ROM labeled
“Printer Drivers and Utilities”.
❖ Network Printing Guide
Describes the procedures and provides necessary information about setting
up and using the printer under the network environment. We recommend
this manual as your first choice to read, and it is included as a PDF file on the
CD-ROM labeled “Printer Drivers and Utilities”.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read This Manual
Symbols
In this manual, the following symbols are used:
R WARNING:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, may result in minor or moderate injury or damage to property.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might be misfed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparations required before op-
erating.
Note
This symbol indicates precautions for operation, or actions to take after misop-
eration.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[
]
Keys that appear on the machine's display panel.
Keys and buttons that appear on the computer's display.
{
}
Keys built into the machine's control panel.
Keys on the computer's keyboard.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Manuals for This Machine......................................................................................i
How to Read This Manual .....................................................................................ii
1. Getting Started
Printer Drivers for This Machine ..........................................................................1
Guide to This Machine...........................................................................................3
Type A........................................................................................................................3
Type B........................................................................................................................6
Network Settings....................................................................................................9
Setting on the Control Panel ......................................................................................9
Other Settings ..........................................................................................................14
Connecting the Machine .....................................................................................16
Requirements...........................................................................................................17
Connecting the Network Cable to the Machine........................................................18
Installing the Printer Driver and Software .........................................................21
Windows 95/98/Me - Installing the Raster Printer Language Printer Driver.............23
3. Basic Printing
Printing.....................................................................................................................31
Changing the Number of Prints During Printing.......................................................34
Printing (Master Making) with the Different Size of Paper from the Original............35
INDEX......................................................................................................... 36
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Getting Started
Printer Drivers for This Machine
Printing requires installation of a printer driver for your operating system. The
following drivers are included on the CD-ROM labeled “Printer Drivers and
Utilities” that comes with the machine.
Printer Language
Raster Printer
Language
Operating system
Windows 95 *1
√
√
√
√
√
√
Windows 98 *2
Windows Me *3
Windows 2000 *4
Windows XP *5
Windows NT 4.0 *6
*1
Microsoft Windows 95 operating system
Microsoft Windows 98 operating system
Microsoft Windows Millennium Edition
Microsoft Windows 2000 Professional
Microsoft Windows 2000 Server
Microsoft Windows XP Professional
Microsoft Windows XP Home Edition
*2
*3
*4
*5
*6
Microsoft Windows NT Server operating system version 4.0, Microsoft Windows NT
Workstation operating system version 4.0 in a computer using x86 processors.
❖ Raster Printer Language printer drivers
See p.24 “Windows 2000/Windows XP- Installing the Raster Printer Lan-
guage Printer Driver”
See p.28 “Windows NT 4.0 - Installing the Raster Printer Language Printer
Driver”
The Printer driver varies depending on the machine model.
Machine model
Type A 600 dpi
Machine resolution
600 dpi
Priter driver
Type40 600
Type A 400 dpi
Type B
400 dpi
400 dpi
Type40 400 A
Type40 400 B
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Software and Utilities Included on the CD-
ROM
1
There is a CD-ROM that comes with the machine. The CD-ROM is labeled
“Printer Drivers and Utilities”. The following items are included on the CD-
ROM:
❖ SmartDeviceMonitor for Admin
This utility is for the system administrator to manage printers on the network.
Reference
See SmartDeviceMonitor for Admin online Help for more information
about using the SmartDeviceMonitor for Admin.
❖ SmartDeviceMonitor for Client
This utility is for users to manage their own print status on the network.
Reference
See SmartDeviceMonitor for Client online Help for more information
about using the SmartDeviceMonitor for Client.
❖ Acrobat Reader
This utility allows you to read PDF (Portable Document Format).
Note
❒ Documentation about using the machine is included on the CD-ROM in
PDF. See Acrobat Reader online Help for more information about using
Acrobat Reader.
Important
❒ If you upgrade to Windows 2000 from Windows 95/98/Me or Windows NT
4.0, the software and utilities must be uninstalled prior to installing Windows
2000. Reinstall them in the Windows 2000 environment.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to This Machine
Guide to This Machine
Note
❒ The location of keys and indicators vary depending on machine models, Type
1
A and Type B.
Type A
Control panel
1
2 3
4
5
Auto On Line
lay
Original Storage
14 13
12 11
10 9 8
7
6
ZDZS200N
1. {User Tools} key
3. {Auto On Line} key
Press to change the default to meet your
requirements.
You can select whether the machine auto-
matically switches to On Line mode
when it receives data from a computer.
2. {On Line} key
Allows data on a computer to be printed
on this machine (online status).
When pressing this key to turn on Auto
On Line, the indicator will light. Then,
when data from a computer is received,
the machine will automatically enter the
On Line status (In this case, it is not nec-
essary to press the {On Line} key).
Note
❒ When the Auto On Line indicator is
lit, the machine will automatically en-
ter the online status when receiving
data from a computer without having
to press the {On Line} key.
4. Display Panel
Shows operation status, error messages,
and function menus.
5. {Clear Modes/Energy Saver} key
Press to cancel the current settings. The
machine settings return to their default.
When the machine is in Energy Saver sta-
tus, press {Clear Modes/Energy Saver} key
to cancel Energy Saver status and to re-
turn to the normal status.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
6. {Print} key
12. Function keys
Press to start printing.
These keys correspond to the selectable
items on the display panel.
7. {Start} key
Press to start master making.
13. Data In indicator (Green)
Indicates the status of this machine:
• On: Data waiting for Master Making
1
8. {#} key
Press to confirm an entered value.
and printing is in the machine.
9. {Clear/Stop} key
Press to delete a number entered or to
stop printing.
• Blinking: Data is being received, or
Master Making or printing is in
progress.
• Off: Master Making and printing are
10. Number keys
completed.
Press to enter the desired number of
prints and data for selected modes.
14. Error indicator (Red)
Indicates the status of this machine:
• On: An error has occurred. Master
Making and printing stop.
• Off: Normal status
11. {~}{}}{|}{{} keys
Use to highlight items you wish to select
on the display panel.
Display panel
The display panel shows the status of the machine, error messages and function
menus.
Important
❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to
the display panel. Otherwise, the display can get damaged.
Displays and key operations
The display panel shows the machine status, error messages, and function men-
us.
1. Items for the selected function.
3. Machine status or messages.
2. These keys correspond to the se-
lectable items shown above them on
the display panel. To select an item
shown on the display panel, press
the key directly below it.
4. Items which can be selected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to This Machine
❖ Common key explanations
[OK]
Confirms a function selection or an entered value.
[Cancel]
Cancels a function selection or an entered value and returns
to the previous display.
1
[Prev.][Next]
When there are too many items to fit on the display panel, use
these keys to move between pages.
{~}{}}{|}{{}[←][→]
Press to highlight items you wish to select on the display pan-
el.
[Select]
Selects a value.
[Exit]
Returns to the previous display.
Note
❒ When you select an item on the display panel, it is highlighted (e.g.
).
Items shown dimmed (e.g.
) cannot be selected.
Offline/Online
The screens displayed are different in the online status and offline status.
Note
❒ When the machine is offline, it cannot receive data from a computer.
❒ When the machine is online, it can receive data from a computer.
1. [Pnt.Size]
Reference
The paper size in the Paper Feed Tray can
For information about the other
setting items on the display panel,
see Operating Instructions.
be selected.
Note
❒ When “Auto” is selected, the paper
size in the Paper Feed Tray will be au-
tomatically detected.
2. [Ppr.Type]
You can specify the type of paper on Pa-
per Feed Tray.
❒ A message “Paper size mismatch...”
appears on the display panel when the
paper size in the Paper Feed Tray is
different from the paper size of data
set on the computer. Set paper of the
correct size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Setting the size of paper
The machine automatically detects the size of paper on Paper Feed Tray, and
then the size of paper appears on the display panel.
1
Type B
Control panel
ZLKS010N
1. {User Tools} key
Press to change the default to meet your
requirements.
4. Display Panel
Shows operation status, error messages,
and function menus.
2. {On Line} key
5. {Cancel} key
Allows data on a computer to be printed
on this machine (online status).
Cancels a function selection or an entered
value and returns to the previous dis-
play.
Note
6. {~}{}} keys
❒ when the Auto On Line indicator is lit,
the machine will automatically enter
the online status when receiving data
from a computer without having to
press the {On Line} key.
Use to highlight items you wish to select
on the display panel.
7. {OK} key
Press to confirm a function selection or an
entered value.
3. {Auto On Line} key
You can select whether the machine auto-
matically switches to On Line mode
when it receives data from a computer.
When pressing this key to turn on Auto
On Line, the indicator will light. Then,
when data from a computer is received,
the machine will automatically enter the
On Line status (In this case, it is not nec-
essary to press the {On Line} key).
8. {Clear Modes/Energy Saver} key
Press to cancel the current settings. The
machine settings return to their default
settings.
When the machine is in Energy Saver sta-
tus, press {Clear Modes/Energy Saver} key
to cancel Energy Saver status and to re-
turn to the normal status.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to This Machine
9. {Print Start} key
Press to start printing.
14. {Job Reset} key
Press to cancel master making.
10. {Make Master} key
Press to start master making.
15. Data In indicator (Green)
Indicates the status of this machine:
1
On: Data waiting for Master Making and
printing is in the machine.
Blinking: Data is being received, or Mas-
ter Making or printing is in progress.
Off: Master Making and printing are
completed.
11. {Clear/Stop} key
Press to delete a number entered or to
stop printing.
12. {#} key
Press to confirm an entered value.
13. Number key
Press to enter the desired number of
prints and data for selected modes.
16. Error indicator (Red)
Indicates the status of this machine:
On: An error has occurred. Master Mak-
ing and printing stops.
Off: Normal status.
Display panel
The display panel shows the status of the machine, error messages and function
menus.
Important
❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to
the display panel. Otherwise, the display can get damaged.
Displays and key operations
The display panel shows the machine status, error messages, and function men-
us.
1. Items for the selected function.
3. Items which can be selected.
2. Machine status or messages.
❖ Common key explanations
{OK} key
Confirms a functions selection or an entered value.
{Cancel} key
Cancels a function selection or an entered value and returns
to the previous display.
{~}{}} key
Press to highlight items you wish to select on the display pan-
el.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Offline/Online
The screens displayed are different in the online status and offline status.
Note
1
❒ When the machine is offline, it cannot receive data from a computer.
❒ When the machine is online, it can receive data form a computer.
1. Paper Size
The size of paper on Paper Feed Tray is
displayed.
2. Print Size
The paper size in the Paper Feed Tray can
be selected.
Note
❒ When “Auto” is selected, the paper
size in the Paper Feed Tray will be au-
tomatically detected.
❒ A message “Paper size mismatch...”
appears on the display panel when the
paper size in the Paper Feed Tray is
different from the paper size of data
set on the computer. Set paper of the
correct size.
Setting the size of paper
The machine automatically detects the size of paper on Paper Feed Tray, and
then the size of paper appears on the display panel.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
Network Settings
You can make the necessary network settings using the control panel of this ma-
chine.
1
It is also possible to use “SmartDeviceMonitor for Admin” when making set-
tings for IP addresses in environments you can use TCP/IP.
Setting on the Control Panel
Make the settings for necessary items for the network environment you are go-
ing to use.
The followings are the items that can be set as well as the factory settings:
Item
Factory settings
011.022.033.044
None
IP Address
Network boot
Type A
A Press the {User Tools} key.
Image Density
Lighter
Stamp
On Line
Normal
Darker 1
Darker 2
Auto On Line
Make-Up
ZDZS110N
The User Tools screen appears.
B Press [Next].
C Select [7 Set O/L Paramet's] using the {~}, {}}, {|} or {{} keys.
D Press [OK].
The Online Parameter Settings items appear.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
E Press [Next].
1
F Set the IP address.
A Select [5 IP Address] using the {~}, {}}, {|} or {{} key.
B Press [OK].
The IP address setting screen appears.
C Enter the IP address using the number keys.
• You can change the numbers that are highlighted.
• The cursor can be moved using the {~} key or the {}} key.
• The numbers are entered 3 digits at a time.
D Press [OK].
After finishing the IP address settings, the screen returns to the screen on
step .
E
G If necessary, make the Network boot settings.
A Select [7 Network] using the {~}, {}}, {|} or {{} keys.
B Press [OK].
The network boot settings screen appears.
C Select the Network boot to be set using the {~}, {}}, {|} or {{} keys.
Valid method *1
Item
AP
b
b
b
RA
BO
DH
ARP+PING
ARP&RARP
ARP&BOOTP
b
b
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
Valid method *1
Item
AP
RA
BO
DH
ARP&RARP&BOOTP
None (Factory Settings)
RARP+TFTP
b
b
b
1
b
b
BOOTP
b
b
RARP&BOOTP
DHCP
b
*1
The valid methods are in order from the left: ARP+PING, RARP+TFTP,
BOOTP, DHCP.
Note
❒ It is necessary to set the server when using RARP+TFTP, BOOTP, and
DHCP.
❒ When setting the IP address on the control panel, use None.
Reference
See Network Printing Guide when using DHCP.
D Press the [OK].
This completes the Network boot settings.
H Press the {User Tools} key.
Image Density
Lighter
Stamp
On Line
Normal
Darker 1
Darker 2
Auto On Line
Make-Up
ZDZS110N
A message “Parameter settings have been changed. You must restart the ma-
chine before the new settings take effect.” appears on the display panel.
I Turn off and on the main power switch of the machine.
The set items become valid.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Type B
A Press the {User Tools} key
1
The User Tools screen appears.
B Select [6 Online Paramet's] using the {~} key or the {}} key.
C Press the {OK} key.
The Online Parameter Settings items appear.
D Set the IP address.
A Select [5 IP Address] using the {~} key or the {}} key.
B Press the {OK} key.
The IP address setting screen appears.
C Enter the IP address using the number keys.
• You can change the numbers that are highlighted.
• The cursor can be moved using the {~} key or {}} key.
• The numbers are entered 3 digits at a time.
D Press the {OK} key.
After finishing the IP address settings, the screen returns to the screen on
step C.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
E If necessary, make the Network boot settings.
A Select [7 Network] using the {~} key or {}} key.
B Press the {OK} key.
The network boot settings screen appears.
1
C Select the Network boot to be set using the {~} key or {}} key.
Valid method *1
Item
AP
b
b
b
b
RA
b
b
b
b
BO
DH
ARP+PING
ARP&RARP
ARP&BOOTP
ARP&RARP&BOOTP
None (Factory Settings)
RARP+TFTP
b
b
BOOTP
b
b
RARP&BOOTP
DHCP
b
*1
The valid methods are in order from the left: ARP+PING, RARP+TFTP,
BOOTP, DHCP.
Note
❒ It is necessary to set the server when using RARP+TFTP, BOOTP, and
DHCP.
❒ When setting the IP address on the control panel, use None.
Reference
See Network Printing Guide when using DHCP.
D Press the {OK} key.
This completes the Network boot settings.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
F Press the {User Tools} key.
1
A message “Parameter settings have been changed. You must restart the ma-
chine before the new settings take effect.” appears on the display panel.
G Turn off and on the main power switch of the machine.
The set items become valid.
Other Settings
The followings are other items you can set using the control panel besides the IP
address and the Network boot:
Note
❒ The settings are performed in Web Status Monitor or SmartDeviceMonitor
for Admin. See the corresponding online Help for details.
Items
Factory Settings
000.000.000.000
Subnet mask
Default gateway address
Access control address
Access control mask
Frame Type (Netware)
Valid protocol
000.000.000.000
000.000.000.000
000.000.000.000
Automatic selection
All valid
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
-About addresses
❖ Subnet mask
Mask value for using one part of an IP Address as a network address.
1
❖ Default gateway address
Host or router address used as a gateway when negotiating with (printing, in-
formation gathering) a workstation on a different network.
Note
❒ Check with your network administrator for the address to be set.
❒ If you do not know the address to be set, use the factory settings.
-About access control
The access control address and the access control mask are used to limit a print-
able workstation, by using an IP address. If it is not necessary to limit printing,
set “0.0.0.0”.
Note
❒ If the access control address mask and the mask of the address of the work-
station trying to print is the same, then access will be granted.
❒ For example, if the access control address is set to 192.168.15.16, depending
on the mask value, the address of the accessible workstation is as follows:
(XXX can be any value).
Access control mask
Accessible Addresses
XXX.XXX.XXX.XXX
192.XXX.XXX.XXX
192.168.XXX.XXX
192.168. 15.XXX
192.168. 15. 16
0. 0. 0. 0
255. 0. 0. 0
255.255. 0. 0
255.255.255. 0
255.255.255.255
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the Machine
❖ Type A
1
2
1
ZGAH140E
❖ Type B
1
2
ZJXH150E
1. Ethernet Interface
2. Parallel Interface
Connector for the 100BASE-TX or
10BASE-T cable used when connect-
ing to the network.
Connector for the parallel interface ca-
ble used when connecting to a compu-
ter.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Machine
Requirements
Requirements
1
Before using this machine, make sure that all the environmental and electrical
requirements have been met. Connect the machine to the host computer using
the parallel port, Network Interface Board, or both.
Make sure that all the cables, connectors, and electrical outlets necessary to at-
tach the machine to the host computer or network are present.
Important
Reference
For Ethernet Board connection, see p.18 “Connecting the Network Cable to
the Machine”.
For more information about using the parallel port, see p.20 “Connecting the
Machine to the Host Using the Parallel Cable”.
Interface cable requirements
As the cables may differ depending on the type of computer, make sure you
check your computer and prepare the appropriate cable.
Note
❒ Use a shielded cable for the interface cable. Using another cable, instead of
shielded cables, may cause radio interference.
Parallel cable requirements
Connect the machine to the host computer using a parallel port. This machine
does not provide the parallel cable to connect the machine to the host computer.
The machine's parallel interface is a standard bidirectional interface. It requires
a standard 36-pin parallel cable compliant with IEEE 1284 and a parallel port
available on the host computer.
Note
❒ Do not use a parallel cable that is longer than 3 meters (10 feet).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the Network Cable to the Machine
Important
❒ Before connecting an interface cable between the machine and a computer,
make sure that the machine is not operating, and then turn off the main power
switches of the machine and the computer.
1
❒ Be sure to use the designated interface cable. Using another cable may cause
radio interference.
After setting up this machine to support the network environment, connect the
Ethernet interface cable. Connect a 10BASE-T or 100BASE-TX cable to the Ether-
net board.
A Connect the Ethernet interface cable into the Ethernet interface at the right
side of the back of the machine.
❖ Type A
❖ Type B
ZJXH170J
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Machine
B Turn on the main power switch.
❖ Using the switches and understanding the LEDs
❖ Type A
1
1
2
3
ZJXH131E
❖ Type B
3
2
1
ZJXH141E
1. Is on while the Ethernet board is
3. Is on while the machine is proper-
working properly.
ly connected to the network.
2. Is on while the 100BASE-TX is
working, and off when the 10BASE-
T is working.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the Machine to the Host Using the Parallel Cable
Connect the machine to the host computer using a parallel cable compliant with
IEEE 1284 (available separately).
1
Follow these steps to connect the machine to the host computer.
Important
❒ Before connecting an interface cable between the machine and a computer,
make sure that the machine is not operating, and then turn off the main power
switches of the machine and the computer.
❒ Be sure to use the designated interface cable. Using another cable may cause
radio interference.
A Plug the 36-pin end of the parallel cable into the parallel port at the right
side on the back of the machine.
B Squeeze the wire clips on each side of the connector together until they
snap into place. The clips hold the cable securely in place.
❖ Type A
❖ Type B
ZJXH160J
C Plug the other end of the parallel cable into the computer's parallel port.
If there are the wire clips, squeeze them on each side of the connector to-
gether.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installing the Printer Driver
and Software
Installing the Printer Driver and Software
This manual assumes that you are familiar with general Windows procedures
and practices. If you are not, see the documentation that comes with Windows
for details.
Note
Reference
For more information about the printer drivers, see p.1 “Printer Drivers for
This Machine”.
For more information about the software and utilities, see p.2 “Software and
Utilities Included on the CD-ROM”.
Important
❒ Before starting the installation, close all documents and applications. In a net-
work environment, make sure that users who are logged on are disconnected.
❒ After installing a printer driver, you must restart the computer.
Note
❒ Use the appropriate language on the CD-ROM folder: ENGLISH (English),
DEUTSCH (German), FRANCAIS (French), ITALIANO (Italian), ESPANOL
(Spanish), NEDRLNDS (Dutch).
❒ The languages displayed in the WSMHLP folder (Web Status Monitor Help)
in the Help folder on the CD-ROM are as follows: DE (German), EN (English),
ES (Spanish), FR (French), IT (Italian), NL (Dutch).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver and Software
-Using the shared printer on Windows 2000/Windows XP or Windows
NT 4.0 for Windows 95/98/Me Client or Windows NT 4.0 Client
❖ Windows 2000/Windows XP
If you want to share the machine on Windows 2000/Windows XP, install the
printer driver of Windows 95/98/Me or Windows NT 4.0 as an alternate
driver.
2
❖ Windows NT 4.0
If you want to share the machine on Windows NT 4.0, install the printer driv-
er of Windows 95/98/Me as an alternate driver.
Note
For more information about installing the printer driver as an alternate driver,
see p.24 “Windows 2000/Windows XP- Installing the Raster Printer Language
Printer Driver”, p.28 “Windows NT 4.0 - Installing the Raster Printer Language
Printer Driver”.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Raster Printer Language Printer Driver
Installing the Raster Printer Language
Printer Driver
This section describes basic instructions for installing the Raster Printer Lan-
guage printer driver. The actual procedure may vary depending on the operat-
ing system. Follow the appropriate procedure below.
2
Important
❒ When updating the printer driver by installing the latest version, you should
uninstall the former version . See “Uninstalling the Printer Driver and Soft-
ware” in Printer Reference 2.
Windows 95/98/Me - Installing the Raster Printer Language
Printer Driver
Preparation
The Windows 95/98 CD-ROM may be required during installation. Make
sure to have the CD-ROM ready before installation.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Double-click the [Add Printer] icon.
[Add Printer Wizard] starts.
D Click [Next].
E Check [Local printer] and click [Next].
A dialog box for selecting the manufacturer and model name appears.
F Click [Have Disk].
A dialog box for installing the printer driver from a disk appears.
G Insert the CD-ROM into the CD-ROM drive.
H Click [Browse].
I Use the [Drives] list box to select the CD-ROM drive.
J In the [Folders] box, double-click [Drivers], and then [WIN9x_ME]. Then dou-
ble-click the folder of the appropriate language for the operating system.
K Click [OK].
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver and Software
L Click [OK].
A dialog box for selecting the machine model appears.
M Click to select the name of the machine whose driver you want to install,
and then click [Next].
Important
❒ Select the printer driver for your machine as shown.
2
Machine model
Type A 600 dpi
Machine resolution
600 dpi
Priter driver
Type40 600
Type A 400 dpi
Type B
400 dpi
400 dpi
Type40 400 A
Type40 400 B
N In the [Available ports] box, click to select [Printer Port], and then click [Next].
A dialog box for changing the printer name appears.
O Change the name of the machine if you want, and then click [Finish].
P The installation is complete.
Windows 2000/Windows XP- Installing the Raster Printer
Language Printer Driver
Limitation
❒ Installing a printer driver requires Manage Printers permission. Members of
the Administrators and Power Users groups have Manage Printers permis-
sion by default. When you install a printer driver, log on using an account
that has Manage Printers permission.
Note
❒ If you want to share the machine on Windows 2000/Windows XP, use the
[Sharing] tab in the [Printer Properties] dialog box to specify the alternate printer
driver. For details, see the operating instructions for Windows 2000/Win-
dows XP.
❒ When prompted for the alternate printer driver location, select the following
folder on the CD-ROM:
• Windows 95/98/ME:\ Drivers \ WIN9x_ME \(Language)
• Windows 2000, Windows XP:\ Drivers \ WIN2000_XP \(Language)
• Windows NT4.0:\ Drivers \ WINNT40 \(Language)
❒ When Raster Printer Language driver of Windows 95/98/Me is shared on
Windows 2000, follow ARTICLE -ID:Q142667 of Microsoft Knowledge Base
to install a printer driver.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Raster Printer Language Printer Driver
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional, access the [Printers and Faxes] window
from [Start] on the taskbar.
2
❒ With Windows XP Home Edition, access the [Printers and Faxes] window by
clicking [Start] on the taskbar. Then click [Control Panel], [Printers and Other
Hardware] and then [Printers and Faxes].
C Double-click the [Add Printer] icon.
[Add Printer Wizard] starts.
Note
❒ With Windows XP, Click [Add a printer].
D Click [Next].
E After making sure that the [Local Printer] option has been selected, click
[Next].
A dialog box for selecting the printer port appears.
F Select the port you want to use, and then click [Next].
A dialog box for selecting the manufacturer and model name appears.
G Click [Have Disk].
A dialog box for installing the driver from a disk appears.
H Insert the CD-ROM into the CD-ROM drive.
I Change the drive name in the list box to the name of the CD-ROM drive,
and then click [Browse].
J Double-click [DRIVERS], and then [WIN2000_XP]. Then double-click the fold-
er of the appropriate language for the operating system.
K Click [Open].
L Click [OK].
A dialog box for selecting the machine model appears.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver and Software
M Click to select the name of the machine whose driver you want to install,
and then click [Next].
A dialog box for changing the printer name appears.
Important
❒ Select the printer driver for your machine as shown.
Machine model
Type A 600 dpi
Machine resolution
600 dpi
Priter driver
Type40 600
2
Type A 400 dpi
Type B
400 dpi
400 dpi
Type40 400 A
Type40 400 B
N Change the name of the machine if you want, and then click [Next].
O If you want to share this machine over the network, select [Share as]. If not,
select [Do not share this printer]. Press [Next] to continue.
Note
❒ When selecting [Share as], if necessary enter the location of the machine
and a comment about the machine.
P In the next dialog box you will be asked to print a test page. Select [No] and
then click [Next].
A confirmation dialog box appears.
Note
❒ Print a test page after completing installation and restarting Windows.
Q Make sure that the settings you have set are correct, and then click [Finish].
Note
❒ If the [Digital Signature Not Found] dialog box appears, click [Yes] to continue
the installation.
R The installation is complete.
Note
❒ When the machine (Type A) is equipped with certain options, make set-
tings for them. See p.27 “Setting up options (Type A only)”.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Raster Printer Language Printer Driver
Setting up options (Type A only)
Limitation
❒ Changing the settings of the machine requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Print-
ers permission by default. When you set up options, log on using an account
that has Manage Printers permission. For details about access authority, see
Help for Windows.
2
Important
❒ If the machine is equipped with certain options, you should set up the options
with the printer driver.
Note
❒ When setting up options, you should access the [Printer Properties] dialog box
from Windows. You cannot set up options by accessing the [Printer Properties]
dialog box from an application.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional, access the [Printers and Faxes] window
from [Start] on the taskbar.
❒ With Windows XP Home Edition, access the [Printers and Faxes] window by
clicking [Start] on the taskbar. Then click [Control Panel], [Printers and Other
Hardware] and then [Printers and Faxes].
B Click the icon of the machine you want to use.
C On the [File] menu, click [Properties].
D Click the [Device Settings] tab.
E Use the [Installable Options] group to select the option, and then select the ap-
propriate setting for the option from the drop-down list box.
F After making the setting you want, click [OK].
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver and Software
Windows NT 4.0 - Installing the Raster Printer Language Printer
Driver
Preparation
The Windows NT CD-ROM may be required during installation. Make sure
to have the CD-ROM ready before installation.
2
Limitation
❒ Installing a printer driver requires Full Control access permission. Members
of the Administrators, Server Operators, Print Operators, and Power Users
groups have Full Control permission by default. When you install a printer
driver, log on using an account that has Full Control permission.
Note
❒ If you want to share the machine on Windows NT 4.0, use the [Sharing] tab in
the [Printer Properties] dialog box to specify the alternate printer driver. For de-
tails, see the operating instructions for Windows NT 4.0.
❒ When prompted for the Windows 95/98/Me alternate printer driver loca-
tion, select the following folder on the CD-ROM:
• \ DRIVERS \ WIN9x_ME \(Language)
❒ When Raster Printer Language driver of Windows 95/98/Me is shared on
Windows NT4.0, follow ARTICLE-ID:Q142667 of Microsoft Knowledge Base
to install a printer driver.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Double-click the [Add Printer] icon.
[Add Printer Wizard] starts.
D After making sure that the [My Computer] option has been selected, click
[Next].
A dialog box for selecting the printer port appears.
E Select the check box of the port you want to use, and then click [Next].
A dialog box for selecting the manufacturer and model name appears.
F Click [Have Disk].
A dialog box for installing the driver from a disk appears.
G Insert the CD-ROM into the CD-ROM drive.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Raster Printer Language Printer Driver
H Change the drive name in the list box to the name of the CD-ROM drive,
and then click [Browse].
I Double-click [DRIVERS], and then [WINNT40]. Then double-click the folder of
the appropriate language for the operating system.
J Click [Open].
K Click [OK].
2
A dialog box for selecting the machine model appears.
L Click to select the name of the machine whose driver you want to install,
and then click [Next].
A dialog box for changing the printer name appears.
Important
❒ Select the printer driver for your machine as shown.
Machine model
Type A 600 dpi
Machine resolution
600 dpi
Priter driver
Type40 600
Type A 400 dpi
Type B
400 dpi
400 dpi
Type40 400 A
Type40 400 B
M Change the name of the machine if you want, and then click [Next].
N If you want to share this machine over the network, select [Shared]. If not,
select [Not shared]. Press [Next] to continue.
Note
❒ When selecting [Shared], if necessary enter the location of the machine and
a comment about the machine.
O In the next dialog box you will be asked to print a test page. Select [No] and
then click [Finish].
Note
❒ Print a test page after completing installation and restarting Windows.
P The installation is complete.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver and Software
2
30
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic Printing
Printing Data from Your Computer on the
Printer
For general printing, printing done with the Auto On Line function is used as an
example for explanation purposes.
Note
❒ Auto On Line is a function that starts printing automatically once printing
starts from a computer. Pressing the {Auto On Line} key on the control panel
lights its indicator and enables the function.
Reference
See Operating Instructions for information about operation details.
Printing
Create some data beforehand to be printed from your computer.
A Make sure that the machine is turned on, and press the {Auto On Line} key if
the Auto On Line indicator is not lit.
Note
❒ When the machine is in Auto On Line status, the indicator will be lit.
B Display the data to be printed on the computer, and then click [Print] from
the [File] menu.
The [Print] dialog box appears.
C Select the machine you want to use in the [Printer] box.
Note
❒ When using Windows 95/98/Me, select the machine you want to use in
the [Name] list box.
D Click [Preference] to display the [Printer Properties] dialog box, and then click
[Advanced] on [Paper/Quality] tab or [Layout] tab.
Note
❒ When using Windows 95/98/Me/NT 4.0, enter the number of prints re-
quired, and select the print range, and then click [OK] to start printing.
❒ When using Windows 2000, click [Advanced] on the [Paper/Quality] tab or the
[Layout] tab.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Printing
Printing without proof printing
Note
❒ “Auto-Print after Master Making” in Auto On Line status is available to Win-
dows 2000/XP only.
A Click “Auto-Print after Master Making” in [Printer features], and then select
“On” in the [Change Setting for] box.
B Click [Apply], and then [OK].
3
C Enter the number of prints required, and select the print range.
D Click [OK] to start printing.
When the machine receives data from the computer, it enters the online status
and Data In indicator flashes.
Note
❒ To stop the machine before Master Making, press [Job Reset] (When using
Type B, press the {Job Reset} key). However, for a page where Master
Making has begun, Master Making cannot be cancelled even if [Job Reset]
(When using Type B, press the {Job Reset} key) is pressed.
❒ To stop the machine during printing, press the {Clear/Stop} key. If there is
incoming data from the computer to the machine, press [Job Reset] (When
using Type B, press the {Job Reset} key) to clear it.
Printing after proof printing
Note
❒ “Auto-Print after Master Making” in Auto On Line status is available to Win-
dows 2000/XP only.
A Click “Auto-Print after Master Making” in [Printer features], and then select
“Off” in the [Change Setting for] box.
B Click [Apply], and then [OK].
C Enter the number of prints required, and select the print range.
D Click [OK] to start printing.
When the machine receives data from the computer, it enters the online status
and Data In indicator flashes. The Proof Printing page is output.
Note
❒ To stop the machine before Master Making, press [Job Reset] (When using
Type B, press the {Job Reset} key).
❒ If the {Proof} key is pressed, Proof Printing can be performed again.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Data from Your Computer on the Printer
E Check the result of the proof print.
F Press the {Print} key (When using Type B, press the {Print Start} key).
Printing starts.
Note
❒ To stop the machine during printing, press the {Clear/Stop} key. If there is
incoming data from the computer to the machine, press [Job Reset] (When
using Type B, press the {Job Reset} key) to clear it.
❒ When there is no data to be printed afterwards, “Ready for Master Mak-
ing/Printing” is displayed on the display panel.
3
❒ As this machine performs Proof Printing, one more set than the set number
will be printed. For example, if the set number was two, three print sets
will be printed and delivered.
Printing a “waiting” print job
❖ Type A
When a print job acquires “waiting” status during printing, these three dis-
plays will appear alternately.
A Press the {Print} key.
Note
❒ When the printing is finished, the machine starts master making and print-
ing the next job. When all jobs are finished, the initial display returns.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Printing
❖ Type B
When a print job acquires “waiting” status during printing, these three dis-
plays will appear repeatedly.
3
A Press the {Print Start} key.
Note
❒ When the printing is finished, the machine starts master making and print-
ing the next jobs. When all jobs are printed, the initial display returns.
Changing the Number of Prints During Printing
You can change the number of prints on the machine while it is printing.
Important
❒ Change the number of prints for individual pages. For example, when the
machine is printing the second page and you change the number of prints
from one to two, the second page will be printed twice. The first page and
pages from the third page on will only be printed once.
A Press the {Clear/Stop} key when printing a page for which you want to
change the number of prints.
When printing is interrupted, “Processing” will be displayed.
Note
❒ When canceling printing from the following pages, press [Job Reset]
(When using Type B, press the {Job Reset} key).
B Enter the number of prints using the number keys on the machine.
C Press the {Print} key (When using Type B, press the {Print Start} key).
Printing restarts. When the specified number has been printed, Master Mak-
ing of the next page begins.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Data from Your Computer on the Printer
Printing (Master Making) with the Different Size of Paper from the
Original
When printing data with the different size of paper from the original, an error
message will appears on the machine's display panel, however, you can print it
forcibly.
Type A
A Print data from your computer.
3
The error message appears.
B Press [MakeMstr].
The status message appears.
C Set the paper to use on Paper Feed Tray, and then press [OK].
Note
❒ When you want to cancel printing, press [JobReset].
Type B
A Print data from your computer.
The error message appears.
B Press the {Make Master} key.
The status message appears.
C Set the paper to use on Paper Feed Tray, and then press the {OK} key.
Note
❒ When you want to cancel printing, press the {Job Reset} key.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
I
Access Control, 15
Access control address, 14
Access control mask, 14
Auto On Line key
Type A, 3
IP Address, 9
K
# key
Type B, 6
Type A, 4
Type B, 7
C
Cancel key (Type B), 6
Cancel (Type A), 5
Clear Modes/Energy Saver key
Type A, 3
M
Type B, 6
Clear/Stop key
Type A, 4
N
Network Settings, 9
Next (Type A), 5
Number key
Type B, 7
Number keys
Type A, 4
Type B, 7
Connecting the Machine, 16
Control panel
Type A, 3
Type B, 6
D
Data In indicator (Green)
Type A, 4
On Line key
Type B, 7
Display, 4
Display Panel
Type A, 3
Type A, 3
Type B, 6
Type B, 6
Display panel, 4
E
Pnt.Size, 5
Prev. (Type A), 5
Prinnt Size, 8
Error indicator (Red)
Type A, 4
Type B, 7
Ethernet Interface, 16
Exit (Type A), 5
Windows, 31
Print key (Type A), 4
Print Start key (Type B), 7
F
Frame Type (Netware), 14
Function keys, 4
36
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Raster Printer Language, 1
Windows 2000, Install, 24
Windows 95/98/Me, Install, 23
Windows XP, Install, 24
S
Select (Type A), 5
SmartDeviceMonitor for Admin, 2
SmartDeviceMonitor for Client, 2
Start key (Type A), 4
Subnet mask, 14
U
User Tools key
Type A, 3
Type B, 6
V
Valid protocol, 14
W
Windows 2000
Raster Printer Language, Install, 24
Windows 95/98/Me
Raster Printer Language, Install, 23
Windows NT 4.0
Raster Printer Language, Install, 28
Windows XP
Raster Printer Language, Install, 24
37
Download from Www.Somanuals.com. All Manuals Search And Download.
38
EN
USA
C624-8617
Download from Www.Somanuals.com. All Manuals Search And Download.
Note to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Caution (in case of 100BaseTX environment):
Network interface cable with ferrite core must be used for RF interference suppression.
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Copyright © 2003
Download from Www.Somanuals.com. All Manuals Search And Download.
EN USA C624-8617
Download from Www.Somanuals.com. All Manuals Search And Download.
|