1502/1802/1802d
Operating Instructions
Copy Reference
ZENH010E.eps
Read this manual carefully before you use this product and keep it handy for future
reference.
For safety, please follow the instructions in this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine all operators should carefully read and follow the instructions in
this manual. Please keep this manual in a handy place near the machine.
Please read the Safety Information in the Copy Reference before using this machine. It contains im-
portant information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Notes
Some illustrations may be slightly different from your machine.
Certain options may not be available in some countries. For details, please contact your local dealer.
Operator Safety
This machine is considered a CDRH class I laser device, safe for office/EDP use. The machine con-
tains a 5-milliwatt, 760-800 nanometer wavelength, GaAIAs laser diode. Direct (or indirect reflected )
eye contact with the laser beam might cause serious eye damage. Safety precautions and interlock
mechanisms have been designed to prevent any possible laser beam exposure to the operator.
Laser Safety:
The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical unit
in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite
equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser
chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis
and laser subsystems to the factory or service depot when replacement or the optical subsystem is re-
quired.
Warning:
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details, see P.iv “Machine Types”.)
•
•
Type 1: 15 copies/minute (A4K, 81/2" × 11"K)
Type 2: 18 copies/minute (A4K, 81/2" × 11"K)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as above. For details about power source,
see P.69 “Power Connection”.
Download from Www.Somanuals.com. All Manuals Search And Download.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
When using your equipment, the following safety precautions should always be
followed.
Safety During Operation
In this manual, the following important symbols are used:
R WARNING:
Indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
Indicates a potentially hazardous situation which, if instructions are not
followed, may result in minor or moderate injury or damage to property.
R WARNING:
•
•
•
Connect the power cord directly into a wall outlet and never use an ex-
tension cord.
Disconnect the power plug (by pulling the plug, not the cable) if the
power cable or plug becomes frayed or otherwise damaged.
To avoid hazardous electric shock or laser radiation exposure, do not
remove any covers or screws other than those specified in this man-
ual.
•
Turn off the power and disconnect the power plug (by pulling the plug,
not the cable) if any of the following conditions exists:
•
•
•
You spill something into the equipment.
You suspect that your equipment needs service or repair.
Your equipment's cover has been damaged.
•
•
•
Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
Disposal can take place at our authorized dealer or at appropriate col-
lection sites.
Dispose of the used toner cartridge in accordance with the local reg-
ulation.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
R CAUTION:
•
•
Protect the equipment from dampness or wet weather, such as rain, snow,
and so on.
Unplug the power cord from the wall outlet before you move the equipment.
While moving the equipment, you should take care that the power cord will
not be damaged under the equipment.
•
•
•
•
When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
Do not allow paper clips, staples, or other small metallic objects to fall inside
the equipment.
Keep toner (used or unused) and toner cartridge out of the reach of chil-
dren.
For environmental reasons, do not dispose of the equipment or expended
supply waste at household waste collection points. Disposal can take place
at an authorized dealer or at appropriate collection sites.
•
•
The inside of the machine could be very hot. Do not touch the parts with a
label indicating the “hot surface”. Otherwise it could cause a personal burn.
Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you only use the expendable supplies avail-
able at an authorized dealer.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Manual
Symbols
In this manual, the following symbols are used:
R WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury when you misuse the machine without following the in-
structions under this symbol. Be sure to read the instructions, all of which are de-
scribed in the Safety Information section.
R CAUTION:
This symbol indicates a potentially hazardous situation that might result in mi-
nor or moderate injury or property damage that does not involve personal injury
when you misuse the machine without following the instructions under this
symbol. Be sure to read the instructions, all of which are described in the Safety
Information section.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might be misfed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparations required before op-
erating.
Note
This symbol indicates precautions for operation, or actions to take after misop-
eration.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
{
}
Keys built into the machine's operation panel.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Types
This machine comes in two models which vary in copy speed.
Type 1
Type 2
15 copies/minute (A4K, 81/2" 18 copies/minute(A4K, 81/2"
Copy speed
× 11"K)
Option
Option
× 11"K)
Option
Option
Fax unit
Printer unit
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
What You Can Do with This Machine
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Guide to Components............................................................................... 1
Options....................................................................................................... 3
Operation Panel......................................................................................... 4
Panel Display ............................................................................................. 6
Displays and Key Operations........................................................................ 6
1.Basics
Turning on the Power................................................................................ 7
Turning on the Main Power........................................................................... 7
Starting the Machine ..................................................................................... 8
Changing Modes........................................................................................ 9
Originals................................................................................................... 10
Sizes and Weights of Recommended Originals.......................................... 10
Sizes Difficult to Detect ............................................................................... 11
Original Sizes and Scanning Area/Missing Image Area.............................. 12
Copy Paper............................................................................................... 13
Recommended Paper Sizes and Types...................................................... 13
Non-recommended Paper........................................................................... 15
Paper Storage............................................................................................. 16
Toner......................................................................................................... 17
Handling Toner............................................................................................ 17
Toner Storage ............................................................................................. 17
Used Toner ................................................................................................. 17
2.Copying
Basic Procedure ...................................................................................... 19
Setting Originals...................................................................................... 21
Placing Originals on the Exposure Glass.................................................... 21
Loading Originals in the Document Feeder................................................. 22
Setting Custom Original Size in the Document Feeder............................... 23
Basic Functions....................................................................................... 25
Adjusting Copy Image Density.................................................................... 25
Selecting an Original Type.......................................................................... 25
Selecting Copy Paper ................................................................................. 26
Auto Reduce/Enlarge.................................................................................. 28
Sort ........................................................................................................... 29
Sort.............................................................................................................. 29
Copying from the Bypass Tray .............................................................. 31
Other Functions....................................................................................... 35
User Codes ................................................................................................. 35
Auto Start .................................................................................................... 35
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Reduce/Enlarge ........................................................................... 36
Zoom......................................................................................................... 37
Combine................................................................................................... 38
Series Copies........................................................................................... 40
Book→1 Sided ............................................................................................ 40
Combination Chart .................................................................................. 41
3.Troubleshooting
If Your Machine does not Operate as You Want................................... 43
Message...................................................................................................... 43
Display ........................................................................................................ 44
If You Cannot Make Clear Copies .......................................................... 45
If You Cannot Make Copies as You Want.............................................. 46
Combine...................................................................................................... 46
B Loading Paper..................................................................................... 47
Loading paper in the optional paper tray unit.............................................. 47
D Changing the Toner Cartridge........................................................... 49
x Clearing Misfeeds............................................................................... 51
Changing the Paper Size ........................................................................ 54
Changing the Paper Size in the Paper Tray................................................ 54
Changing the Paper Size in the Optional Paper tray unit............................ 56
4.User Tools (Copier Features)
Accessing the User Tools (Copier Features)........................................ 59
Exiting the User Tools................................................................................. 60
User Tools Menu (Copier Features)....................................................... 61
Settings You Can Change with the User Tools .................................... 62
Copier Features .......................................................................................... 62
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Remarks
Do's and Don'ts ....................................................................................... 67
Where to Put Your Machine.................................................................... 68
Machine Environment ................................................................................. 68
Power Connection....................................................................................... 69
Access to Machine...................................................................................... 70
Maintaining Your Machine...................................................................... 71
Cleaning the Exposure Glass...................................................................... 71
Cleaning the Platen Cover .......................................................................... 71
Cleaning the Document Feeder .................................................................. 71
6.Specification
Mainframe................................................................................................. 73
Document Feeder (ADF) (Option) .......................................................... 77
Paper Tray Unit (1-tray type) (Option) ................................................... 78
Paper Tray Unit (2-tray type) (Option) ................................................... 79
16MB Copier Memory Unit (Option)....................................................... 80
32MB DIMM (Option) ............................................................................... 81
INDEX........................................................................................................ 82
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Components
1. Platen cover or document feeder
5. Main power switch
(ADF) (option)
If the machine does not operate after
turning on the operation switch, check if
the main power switch is turned on. If it
is off, turn it on. However, if the machine
is installed with the fax option, do not
turn the main power off.
Lower the platen cover over originals
placed on the exposure glass for copying.
If you have the document feeder, insert a
stack of originals here. They will be fed
automatically.
6. Main Power indicator
2. Exposure glass
This indicator lights up when the main
power switch is turned on, and goes off
when the switch is turned off.
Position originals here face down for cop-
ying. See P.10 “Originals”.
3. Internal tray
Copied paper is delivered here face
down.
7. On indicator
This indicator lights up when the opera-
tion switch is turned on, and goes off
when the switch is turned off.
4. Ventilation hole
Prevents overheating. Do not obstruct
the ventilation hole by placing or leaning
an object near it. If the machine over-
heats, a fault might occur.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation switch
11. Paper tray
Press this switch to turn the power on
(the On indicator lights up). To turn the
power off, press this switch again (the On
indicator goes off).
Set paper here. See P.47 “B Loading Pa-
per”.
12. Paper tray unit (option)
There are two types of paper tray unit, 1–
tray type and 2–tray type, and each tray
holds 500 sheets of paper.
9. Operation panel
See P.4 “Operation Panel”.
10. Front cover
Open to access the inside of the machine.
1. Bypass tray
3. Lower right cover (Type 2 only)
Use to copy onto OHP transparencies,
adhesive labels, translucent paper, post
cards, and non-standard size paper. See
P.31 “Copying from the Bypass Tray”.
Open this cover to remove jammed paper
fed from the paper tray unit.
4. Lower right cover
Open this cover to remove jammed paper
from the optional paper tray unit.
2. Right cover
Open this cover to remove jammed paper
fed from the paper tray.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
1. Platen cover
3. Paper tray unit (1-tray type)
Lower this cover over originals for copy-
ing.
Holds 500 sheets of paper.
4. Paper tray unit (2-tray type)
Holds up to 1,000 sheets of paper. Each
paper tray holds 500 sheets of paper.
2. Document feeder (ADF)
Insert a stack of originals here.
They will be fed automatically.
Other options:
• 16MB copier memory unit (Type 1 only)
Increases copier features, allowing you to use Sort or Combine features.
Note
❒ For North American users, a 16MB copier memory unit is installed as the
standard.
• 32MB DIMM
Increases memory capacity, allowing you to increase the data of originals to
be stored. For Type 1, it is available only when the optional 16MB copier
memory unit is installed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Panel
❖ Copier only
❖ Fax or printer installed
1. Indicators for fax mode (for ma-
chines with the optional fax func-
tion)
6. Indicators
These indicators show errors or the status
of the machine. See P.43 “Troubleshoot-
ing”.
See the Facsimile Reference manual.
7. {Cancel} key
Press to cancel an operation or return to
the previous display.
2. {Facsimile} key (for machines
with the optional fax function)
Press to use facsimile functions.
8. Panel display
3. {Printer} key (for machines with
the optional printer function)
Press to use printer functions.
Shows operation status, error messages,
and function menu. See P.6 “Panel Dis-
play”.
4. {Copy} key (for machines with the
optional fax or printer function)
Press to use copy functions.
9. 01 keys (Cursor keys)
Press to select an item on the panel dis-
play.
5. {Auto R/E} key
Enlarges or reduces the image automati-
cally according to the specified paper
size.
10. {OK} key
11. {User Tools/Counter} key
Press to change the default settings and
conditions to meet your requirements.
See P.59 “User Tools (Copier Features)”.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
12. {
Clear/Stop}
key
19. {
Reduce} key
Press to make reduced copies. See P.36
While entering numbers, press to cancel a
number you have entered. While copy-
ing, press to stop copying.
“Preset Reduce/Enlarge”.
20. {Enlarge} key
Press to make enlarged copies. See P.36
“Preset Reduce/Enlarge”.
13. {Clear Modes} key
Press to clear the previously entered copy
job settings.
21. {Zoom} key
Changes the reproduction ratio in 1%
steps.
14. On indicator
This indicator lights up when the opera-
tion switch is turned on, and goes off
when the operation switch is turned off.
22. {Full Size} key
For making full size copies.
15. Fax function keys (Fax installed
23. {Select Paper Tray} key
Press to select the paper tray.
machine only)
Press to change modes. To use copy func-
tions, press the {Copy} key.
24. {Lighter} and {Darker} keys
Adjusts the copy image density.
16. Printer function keys (Printer in-
stalled machine only)
25. {Original Type} key
Press to select the type of your originals.
Press to change modes. To use copy func-
tions, press the {Copy} key.
26. Dial Function keys (for ma-
chines with the optional fax func-
tion)
17. {Sort} key
Automatically sorts copies. Type 1 re-
quires the optional 16MB copier memory
unit.
See the Facsimile Reference manual.
27. Number keys
Use to enter the desired number of copies
and data for selected modes.
18. {Combine/Series} key
•
Combine (Type 1 requires the option-
al 16MB copier memory unit)
Press to make combine copies. See
P.38 “Combine”.
28. {Start} key
Press to start copying. Also use to initiate
Auto Start. See P.35 “Auto Start”.
•
Series (Type 1 requires the optional
16MB copier memory unit)
Press to make series copies. See P.40
“Series Copies”.
29. Operation switch
Press this switch to turn the power on or
return from the low power mode (the On
indicator lights up). To turn the power
off, press this switch again (the On indi-
cator goes off).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Display
The panel display shows the status of the machine, error messages, and function
menus.
Important
❒ Do not apply a strong shock or force of about 30N (about 3kgf) or more to the
panel display. Otherwise, the display might be damaged.
Note
❒ By default, the machine is in Copy mode when you switch on. This can be
changed. See “Settings You Can Change with the User Tools” in the System
Settings manual.
Displays and Key Operations
❖ Copy display
1. Upper line: The machine status or
currently selected functions appear
here.
3. Number of copies set.
2. Bottom line: Items which can be
selected or specified, or messages
appear here. Currently selected
items are displayed with brackets.
❖ Common keys
0 or 1
Press to move between pages or select function.
{Cancel}
Press to cancel an operation or return to the previous display.
{Clear /Stop}
While entering numbers, press to cancel a number you have entered.
While copying, press to stop copying.
{Clear Modes}
Press to cancel the settings and return to the standby mode.
Press to sets a selected function or entered value.
{OK}
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Basics
Turning on the Power
To turn the machine on, press the operation switch.
Note
❒ This machine automatically enters Energy Saver mode or turns itself off if you
do not use the machine for a while. See “6.Auto Off Timer” in the System Set-
tings manual.
-Power switches
This machine has two power switches.
❖ Operation switch (right side of the operation panel)
Press this switch to activate the machine. When the machine has warmed up,
you can make copies.
❖ Main power switch (left side of the machine)
When the machine is not to be used for an extended period of time, turn off
the main power switch.
Turning on the Main Power
A Make sure that the power cord is firmly plugged into the wall outlet.
B Turn on the main power switch.
The main power indicator on the operation panel goes on.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Starting the Machine
A Press the operation switch to make the On indicator go on.
The display panel will come on.
1
Note
❒ If the power is not turned on when the operation switch is pressed, check
if the main power switch is on. If off, turn it on.
❒ During the warm-up period (less than 20 seconds), you can use the Auto
Start function. See P.35 “Auto Start”.
❒ You can set up a copy job and press the {Start} key while the “Select Modes
and Press Start” message is displayed.
❒ When “Input User Code and Press OK” is displayed, enter your user code.
Shutting Down the Machine
A Press the operation switch to make the On indicator go off and change to
Low Power mode.
Turning Off the Main Power
A Turn off the main power switch.
The main power indicator of the operation panel goes off.
Important
❒ Fax files stored in memory will be lost an hour after you turn the main
power switch off or you unplug the power cord.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Modes
Changing Modes
You can use this machine not only as a copier, but optionally as a fax machine or
a printer as well. Press the {Copy} key to use copy functions, or press the {Fac-
simile} key to use facsimile functions.
1
If the display shows a mode other than copy mode, press the {Copy} key to
switch to copy mode.
For how to change the mode the machine starts in when you turn the operation
switch on, see “1.Function Priority” in the System Settings manual.
Limitation
❒ You cannot switch modes in any of the following cases:
• When scanning in a fax message for transmission.
• During immediate transmission.
• When accessing the user tools.
• During on hook dialing for fax transmission.
• During Energy Saver mode.
• When the fax handset is lifted.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Originals
Sizes and Weights of Recommended Originals
1
❖ Metric version
Where original is set
Exposure glass
Original Size
Original Weight
Up to A3
--
40 – 128g/m2
Document feeder
1-sided originals:
A3L – A5KL
❖ Inch version
Where original is set
Exposure glass
Original Size
Original Weight
Up to 11" × 17"
--
Document feeder
1-sided originals: 11" × 17"L – 11 – 34 lb
51/2" × 81/2"KL
Non-recommended originals for the document feeder
Setting the following originals in the document feeder might cause paper mis-
feeds or damage to the originals. Set these originals on the exposure glass.
• Originals other than those specified in P.10 “Sizes and Weights of Recommended
Originals”
• Stapled or clipped originals
• Perforated or torn originals
• Curled, folded, or creased originals
• Pasted originals
• Originals with any kind of coating, such as thermal fax paper, art paper, alu-
minum foil, carbon paper, or conductive paper
• Originals with indexes, tags, or other projecting parts
• Sticky originals such as translucent paper
• Thin originals that have low stiffness
• Originals of inappropriate weight P.10 “Sizes and Weights of Recommended
Originals”
• Bound originals such as books
• Transparent originals such as OHP transparencies or translucent paper
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Originals
Sizes Difficult to Detect
It is difficult for the machine to detect the sizes of the following originals, so se-
lect the paper size manually.
1
• Originals with indexes, tags, or other projecting parts
• Transparent originals such as OHP transparencies or translucent paper
• Dark originals with many letters and drawings
• Originals which partially contain solid images
• Originals which have solid images at their edges
• Originals other than those (marked by ❍) in the table below. See P.11 “Sizes
detectable by the Auto Paper Select”.
Sizes detectable by the Auto Paper Select
❖ Metric version
81/2" 81/2" 81/2" 51/2"
Size A3
L
B4
JIS
L
A4
K
L
B5
JIS JIS
K
B5
A5
K
A5
L
11" 11"
×
×
×
×
×
×
81/2"
K
L
17" 15"
14" 13" 11"
Where
setting
original
L
L
L
L
K
L
L
Exposure
glass
❍
❍
❍
❍
❍
❍
❍
×
×
×
×
×
×
❍
×
×
×
Document
feeder
❍
❍
❍
❍
×
×
×
❍
×
❖ Inch version
81/2" 81/2" 81/2"
51/2"
×
Size A3
L
B4
JIS
L
A4
K
L
B5
JIS
K
L
A5
K
11"
×
17"
L
10"
×
14"
L
8"
×
10"
K
×
×
13"
L
×
Where
setting
original
81/2"
K
L
14"
L
11"
K
L
L
Exposure
glass
×
×
×
×
×
×
×
×
×
❍
❍
×
×
❍
❍
❍
❍
❍
❍
×
×
×
Document
feeder
×
❍
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Original Sizes and Scanning Area/Missing Image Area
❖ Exposure glass
1
Reference
A3
position
Horizontal size
Maximum Scanning area
A3
(297x420mm)
(279x432mm)
11"x17"
A4 A3
CP01AEE
❖ Document feeder
Limitation
❒ Even if you correctly set originals in the document feeder or on the exposure
glass, 4mm, 0.2" margins on all four sides might not be copied.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy Paper
Copy Paper
Recommended Paper Sizes and Types
1
The following limitations apply to each tray:
Metric version
Inch version
Paper weight
Paper capacity
60 – 90g/m2,
16 – 24 lb
250 sheets *1
Paper Tray 1, 2
A3L, B4JISL, A4KL, B5JISKL,
A5K, 11" × 17"L, 81/2" × 14"L,
81/2" × 13"L, 81/4" × 14"L, 81/4" ×
13"L, 8" × 13"L, 81/2" × 11"KL,
71/4" × 101/2"L, 51/2" × 81/2"K,
8KL *3 , 16KKL *4
Note
❒
You can specify the paper size
with the user tools or the paper
size selector. See P.54 “Changing
the Paper Size”.
60 – 105g/m2,
500 sheets *1
Paper tray unit
(option)
A3L , B4JISL , A4KL , B5JISKL
, A5KL , 11" × 17"L, 81/2" × 14"L, 16 – 28 lb
81/2" × 13"L, 81/4" × 14"L, 81/4" ×
13"L, 8" × 13"L, 81/2" × 11"KL,
71/4" × 101/2"KL, 51/2" × 81/2"L,
8KL *3 , 16KKL *4
Note
❒
You can specify the paper size
with the user tools or the paper
size selector. See P.54 “Changing
the Paper Size”.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Metric version
Inch version
Paper weight
Paper capacity
10 sheets *1
52 – 162g/m2,
14 – 43 lb
Bypass
tray
Standard
Sizes
A3L , B4JISL
100 sheets *1
A4KL,
B5JISKL,
A4KL,
B5JISKL,
1
A5KL, B6JISL A5KL,
B6JISL
11"
×
17"L *2
,
11"
81/2"
13"(F4)L, 81/2"
×
17"L *2
,
81/2"
81/2"
81/4"
×
×
×
14"L,
×
×
×
14"L,
13"(F4)L,
13"L, 8"
13"L, 8"
×
81/4"
×
13"(F)L, 81/2"
11"KL, 71/4"
×
×
13"(F)L, 81/2"
11"KL, 71/4"
×
×
101/2"KL, 51/2" 101/2"KL, 51/2"
×
81/2"L, 8KL*3
,
×
81/2"L, 8KL*3
16KKL *4
,
16KKL *4
60 – 157g/m2,
16 – 42 lb
10 sheets *1
40 sheets *1
A3L, B4JISL
A4KL, B5JISKL, A5KL,
B6JISL
11" × 17"L, 81/2" × 14"L, 81/2" ×
13"L, 81/4" × 13"L, 8" × 13"L, 81/2"
× 11"KL, 71/4" × 101/2"KL, 51/2"
× 81/2"L, 8KL *3 , 16KKL *4
Note
❒
You can specify the paper size.
See P.31 “Copying from the Bypass
Tray”.
Non-stand- Translucent paper (A3L , B4JISL),
10 sheets
40 sheets
1 sheets
ard sizes *5
OHP transparencies
Translucent paper (A4KL,
B5JISKL), postcards
Adhesive labels (B4JISL, A4L)
*1
Paper weight: 80g/m2, 20 lb
*2
When you set non-standard size paper in the bypass tray, You can specify the size.
See P.31 “Copying from the Bypass Tray”.
*3
*4
*5
8K(Ba-Kai) = 267 × 390 mm, 10.6" × 15.4"
16K(Shi-Lui-Kai) = 195 × 267 mm, 7.7" × 10.6"
Set one sheet at a time for your needs. See P.31 “Copying from the Bypass Tray”.
Important
❒ If you use damp or curled paper, a misfeed might occur. In such a case, try
turning over the paper stack in the paper tray. If there is no improvement,
change to copy paper with less curl.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy Paper
Note
❒ When you use the bypass tray, it is recommended to set the copy paper direc-
tion to L.
❒ Postcards should be fed from the bypass tray.
1
❒ If you load paper of the same size and in the same direction in two or more
trays, the machine automatically shifts to another tray when the tray in use
runs out of paper. This function is called Auto Tray Switch. This saves inter-
rupting a copy run to replenish paper even when you make a large number
of copies. You can cancel this setting. See “10Auto Tray Switch” of the System
Settings manual.
Reference
If you want to add paper, see P.47 “B Loading Paper”.
If you want to change the paper size, see P.54 “Changing the Paper Size”.
Non-recommended Paper
R CAUTION:
•
Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or equipment failure.
Important
❒ Do not use any of the following kinds of paper or a fault might occur.
• Thermal fax paper
• Art paper
• Aluminum foil
• Carbon paper
• Conductive paper
❒ Do not use copy paper that has been already copied on. Otherwise, a paper
misfeed might occur.
Note
❒ Do not use any of the following kinds of paper or a misfeed might occur.
• Bent, folded, or creased paper
• Torn paper
• Slippery paper
• Perforated paper
• Rough paper
• Thin paper that has low stiffness
• Paper with much paper dust on its surface
❒ If you make copies on rough grain paper, the copy image might be blurred.
❒ Do not use paper which has been copied or printed on.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Paper Storage
Note
❒ When storing paper, the following precautions should always be followed:
1
• Do not store paper where it will be exposed to direct sunlight.
• Avoid storing paper in humid areas (humidity: 70% or less).
• Store on a flat surface.
❒ Keep open reams of papers in the package, and store as you would unopened
paper.
❒ Under high temperature and high humidity, or low temperature and low hu-
midity conditions, store papers in a plastic bag.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Toner
Toner
Handling Toner
1
R WARNING:
•
Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations for plastics.
R CAUTION:
•
Keep toner (used or unused) and toner containers out of reach of children.
R CAUTION:
•
Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you only use the expendable supplies availa-
ble at an authorized dealer.
Important
❒ If you use toner other than that recommended type, a fault might occur.
Reference
If you want to add toner, see P.49 “D Changing the Toner Cartridge”.
Toner Storage
Note
❒ When storing toner, the following precautions should always be followed:
• Store toner containers in a cool, dry place free from direct sunlight.
• Store on a flat surface.
Used Toner
Note
❒ Used toner cannot be re-used.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Copying
Basic Procedure
A Make sure that the machine is in
F Enter the number of copies re-
Copy mode.
quired with the number keys.
Note
❒ If not, press the {Copy} key.
B When the machine is set for user
codes, enter the user code with
the number keys and then press
the {#} or {OK} key.
Note
Reference
❒ The maximum copy quantity
can be set between 1 and 99 (de-
fault: 99). See “2.Max. Copy
Q’ty” in P.62 “Copier Features”.
See P.35 “User Codes”.
C Make sure that there are no previ-
ous settings remaining.
❒ To change the number entered,
press the {Clear/Stop} key and
enter the new number.
Note
❒ To clear settings, press the
{Clear Modes} key.
G Press the {Start} key.
D Set your originals.
The machine starts copying.
Reference
See P.21 “Setting Originals”.
Note
❒ To stop the machine during the
multi-copy run, press the {Clear/
Stop} key.
E Set the desired settings.
❒ To return the machine to the in-
itial condition after copying,
press the {Clear Modes} key.
❒ For Type 1 without the optional
16MB copier memory unit, you
cannot copy more than 1 page
from the document feeder.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
-System Reset
The machine returns to its prioritized
mode automatically after your job is
finished, after a certain period of
time. This function is called “System
Reset”.
2
Note
❒ You can change the System Reset
time. See “3.System Reset” in the
System Settings manual.
-Auto Off
The machine turns itself off automat-
ically after your job is finished, after a
certain period of time. This function is
called “Auto Off”.
Note
❒ How to exit Auto Off mode de-
pends on your machine configura-
tion:
• Copier only — press the main
power switch
• Copier and fax or printer —
press the operation switch
❒ You can change the Auto Off time.
See “6.Auto Off Timer” in the Sys-
tem Settings manual.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Originals
Setting Originals
Limitation
Placing Originals on the
Exposure Glass
❒ Set originals after correction fluid
and ink has completely dried. Not
taking this precaution could mark
the exposure glass and cause
marks to be copied.
A Lift the platen cover or the docu-
2
ment feeder.
Note
Note
❒ Basically the originals should be
aligned to the rear left corner.
However, some copy functions
may produce different results de-
pending on the direction of the
originals. For details, see explana-
tions of each function.
❒ Be sure to open the platen cover
or the document feeder by more
than 30°, otherwise the original
size might not be detected cor-
rectly.
B Set the original face down on the
exposure glass. The original
should be aligned to the rear left
corner.
Originals
Document Exposure
feeder glass
1. Reference mark
2. Scale
Reference
See P.10 “Originals”.
C Lower the platen cover or the doc-
ument feeder.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Setting a stack of originals in the
document feeder
Loading Originals in the
Document Feeder
A Adjust the guide to the original
Note
size.
❒ The original might become dirty if
it is written with a pencil or similar
tools.
B Set the aligned originals face up
into the document feeder.
2
❒ You cannot set a multi-page origi-
nal with pages of different sizes in
the document feeder. If your origi-
nal contains pages of different siz-
es, use the SADF function and set
each page one at a time. Alterna-
tively, set pages one at a time on
the exposure glass.
❒ Do not place any foreign objects on
the document feeder or cover it
with your hand. This could cause
the size not to be detected proper-
ly.
1. Limit mark
2. Document guide
❖ ADF
Note
❒ Do not stack originals above the
limit mark.
❒ To avoid a multi-sheet feed,
shuffle the originals before set-
ting them in the document feed-
er.
1. Sensor
Reference
Regarding originals that the docu-
ment feeder can handle, see P.10
“Originals”.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Originals
When SADF mode is selected
Setting Custom Original Size
in the Document Feeder
A Set one original face up into the
document feeder. Then press the
{Start} key.
Limitation
❒ Enter the size of your original if it
is not one of the following: A3L ,
B4JISL, A4KL, B5JIS KL,
A5KL, 11"× 17"L, 11"× 15"L,
81/2" × 14"L, 81/2" × 13"L, 81/2" ×
11"KL, 51/2" × 81/2"L
❒ For ADF, the paper size that can be
set with this function is vertical
105–297mm, 4" × 12", horizontal
128–1,260mm, 5" × 50".
B When the machine instructs you
to set another original, set the
next page.
2
The second and subsequent origi-
nals can be fed automatically with-
out pressing the {Start} key.
❒ The maximum copy paper size is
Note
297 × 432mm, 11" × 17".
❒ You can adjust the time the ma-
chine waits before being ready
for the next original. See
“6.SADF Auto Reset”in P.62
“Settings You Can Change with
the User Tools”.
❒ You cannot use the Auto Paper Se-
lect function with this function.
A Set one original face up into the
document feeder.
B Press the {Select Paper Tray} to se-
lect your desired paper tray or by-
pass tray.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
D Enter the vertical size of the
original with the number keys,
then press the {OK} or {#} key.
Selecting paper from a paper tray
A Press the {#} key.
C Press the {Start} key.
B Enter the horizontal size of the
original with the number keys,
then press the {OK} key.
2
C Enter the vertical size of the
original with the number keys,
then press the {OK} or {#} key.
Selecting paper from the bypass
tray
A Press the {#} key.
B Press the 0 or 1 key until
“3.Custom Orig. Size" is dis-
played, then press the {OK}
key.
C Enter the horizontal size of the
original with the number keys,
then press the {OK} key.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
Basic Functions
The following basic functions are ex-
plained in this section.
Adjusting Copy Image Density
❖ Adjusting Copy Image Density
You can adjust the copy image densi-
ty to match your originals.
❖ Selecting an Original Type
Text and Photo
2
If you require darker or lighter cop-
ies, adjust the image density yourself.
❖ Selecting Copy Paper
Auto Paper Select and Manual Pa-
per Select
A Press the {Lighter} or {Darker} key
to adjust the image density.
❖ Auto Reduce/Enlarge
The machine can choose an appro-
priate reproduction ratio based on
the paper and original sizes you se-
lect.
Note
❒ You can select functions to be acti-
vated when System Reset is turned
on, when Energy Saver is turned
off, or after the machine is pow-
ered on. See P.62 “Copier Features”.
Selecting an Original Type
❒ You can change default settings for
basic functions. See P.62 “Settings
You Can Change with the User
Tools”.
There are two ways to match your
originals:
❖ Text
If you do not select either mode,
your originals will be scanned
with the settings suitable for text
originals (Text mode).
❖ Photo
Delicate tones of photographs and
pictures can be reproduced with
this mode.
Note
❒ You can change the detailed set-
tings for Text and Photo each with
the User Tools. See P.62 “Settings
You Can Change with the User
Tools”.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❖ Manual Paper Select
A Press the {Original Type} key and
You can select the desired copy pa-
per size manually. You can also se-
lect the bypass tray.
select the original type.
Reference
See P.31 “Copying from the By-
pass Tray”.
2
Note
❒ When you use Auto Paper Select,
refer to the following table for pos-
sible copy paper sizes and direc-
tions (if the ratio is 100%).
Note
❖ Metric version
❒ Press the {Original Type} key to
step through the following
types:
Where original
is set
Paper size and di-
rection
Exposure glass
A3 L, B4JIS L, A4
KL, B5JIS K, 81/2"
× 13" L
Upper indicator lit Text
Lower indicator lit Photo
Document feeder A3 L, B4JIS L, A4
KL, B5JISKL, A5
KL, 81/2" × 13"L
Selecting Copy Paper
There are two ways to select copy paper:
❖ Inch version
❖ Auto Paper Select
Where original
is set
Paper size and di-
rection
The machine selects a suitable size
of copy paper automatically based
on the original size and the repro-
duction ratio.
11"× 17"L, 81/2" ×
14" L, 81/2" × 13"
L, 81/2" × 11" KL
Exposure glass
Note
11"×17"L, 81/2" ×
14" L, 81/2" × 13"
L, 81/2" × 11" KL,
51/2" × 81/2"KL
Document feeder
❒ When the original is set at a dif-
ferent direction from the copy
paper in the paper tray the ma-
chine automatically rotates the
original image by 90 to match
°
❒ For some originals, the original
size might not be detected correct-
ly. See P.11 “Sizes Difficult to De-
tect”.
the copy paper direction (Type 1
requires the optional 16MB cop-
ier memory unit). This applies to
the following paper sizes:
❒ If you specify all papers trays as
containing special paper, you can-
not use the Auto Paper Select func-
tion.
Metric version
A4 KL, B5JIS
KL, A5 KL
81/2" × 11" KL,
Inch version
51/2" × 81/2"KL
(document feeder)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
Original
orientation
Paper
orientation
Rotates the
image and
copies it
A Select the copy paper.
Auto Paper Select
A Make sure that “Auto Paper”
(Auto Paper Select) is selected.
R
GCROTA0E
2
Limitation
❒ You cannot use the Rotated Copy
function when enlarging onto
B4JIS or A3 size paper. In this case,
set your original in the landscape
direction.
Manual Paper Select
A Select the paper tray or bypass
tray by pressing the {Select Pa-
per Tray} key.
You cannot However,
rotate:
you can ro-
tate:
Original
Size and
Direction
A4, B5JIS,
or A5 por-
trait *1
A4, B5JIS,
or A5 land-
scape
↓ when en- ↓ when en-
larging to
larging to
B4JIS, A3 *1
Copy paper
Size and
B4JIS, A3
Direction
-Rotate Copy (Type 1 requires
the optional 16MB copier
memory unit)
*1
For inch version, 11" × 17", 81/2" ×
14", 8 1/2" × 13", 81/4" × 14", 81/4" ×
13" and 8" × 13".
If the direction in which your original
is set (landscape or portrait) is differ-
ent from the paper you are copying
onto, this function rotates the original
image by 90° and fits it on the copy
paper. This function works when
Auto Paper Select or Auto Reduce/
Enlarge are selected. See “Auto Paper
Select” in P.26 “Selecting Copy Paper”
and P.28 “Auto Reduce/Enlarge”.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ You can change the reproduction
ratio from 50 – 200 %.
Auto Reduce/Enlarge
❒ For some originals, the original
size might not be detected correct-
ly. See P.11 “Sizes Difficult to De-
tect”.
The machine can choose an appropri-
ate reproduction ratio based on the
paper and original sizes you select.
A Press the {Auto R/E} key.
2
Limitation
❒ You cannot use the bypass tray
with this function.
B Select the paper tray by pressing
the {Select Paper Tray} key.
Note
❒ When you use Auto Reduce/En-
large, refer to the following table
for possible original sizes and di-
rections:
C Press the {Start} key.
❖ Metric version
Where
Original size and
original is set direction
Exposure
glass
A3L , B4JIS L, A4 KL,
B5JIS K, 81/2" × 13" L
Document A3 L, B4JIS L, A4 KL,
B5JIS KL, A5 KL, 81/2"
feeder
× 13"L
❖ Inch version
Where
Original size and direc-
original is set tion
11" × 17" L, 81/2" × 14" L,
Exposure
glass
81/2" × 13" L, 81/2" × 11"
KL
11" × 17"L, 81/2" × 14" L,
Document
feeder
81/2" × 11" KL, 51/2" × 81/
2" KL
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort
Sort
Type 1 requires the optional 16MB copier memory unit.
The machine can scan your originals
into memory and automatically sort
the copies.
Sort
Copies can be assembled as sets in se-
quential order.
2
• Sort
• Rotate Sort
❖ Sort
Limitation
❒ The maximum paper length for the
sort function is less than 433 mm.
❒ You cannot use the bypass tray
with the Rotate Sort.
Note
❒ The maximum tray capacity is as
follows. When the number of cop-
ies exceeds the tray capacity, re-
move copies from the tray.
❖ Rotate Sort
❖ Metric version
Internal tray
•
•
B4JIS or larger: 250
sheets (80g/m2)
A4 or smaller: 500
sheets (80g/m2)
Two sorting methods are available:
❖ Inch version
❖ Sort
Copies can be assembled as sets in
sequential order.
Internal tray
•
•
81/2" × 14" or larger:
250 sheets (20 lb)
81/2" × 11" or small-
er: 500 sheets (20 lb)
❖ Rotate Sort
Every other copy set is rotated by
90°KL and delivered to the copy tray.
❒ The maximum tray capacity might
be less than the above when you
use the Rotate Sort.
Note
❒ To switch between Sort and Rotate
Sort modes, access the user tools.
See “9.Sort” in P.62 “Settings You
Can Change with the User Tools”.
❒ The maximum tray capacity might
also be reduced when copy paper
is considerably curled.
❒ The paper sizes that can be used with
the Rotate Sort function are as follows:
Metric version
Inch version
A4KLB5JISKL
81/2" × 11"KL
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ To use the Rotate Sort function,
two paper trays identical in size
and different in direction (K L)
are required.
When setting an original on the
exposure glass or in the
document feeder
A Press the {Sort} key.
Reference
See P.23 “When SADF mode is se-
lected”
2
A Set the original, then press the
{Start} key.
B Set the next original, then
press the {Start} key.
Note
❒ Set the original in the same
direction as the first one.
C After all originals are scanned,
B Enter the number of copy sets
press the {#} key.
with the number keys.
The copies are delivered to the
tray.
Note
❒ By default, the maximum
number of sets is 99. You can
change the default number with
“2.Max. Copy Q’ty” in the copi-
er features. See P.62 “Settings
You Can Change with the User
Tools”.
C Set your originals.
When setting a stack of originals
in the document feeder
A Set a stack of originals in the
document feeder, then press
the {Start} key.
After all the originals are
scanned, the copies are deliv-
ered to the tray.
Note
❒ If an original is misfed, reset
your originals in the docu-
ment feeder according to the
instruction on the display.
The display will indicate the
number of originals you
should return.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Bypass Tray
Copying from the Bypass Tray
Use the bypass tray to copy onto OHP
B Push up the paper guide release
transparencies, adhesive labels, trans-
lucent paper, post cards, and copy pa-
per that cannot be set in the paper tray.
lever.
Note
2
❒ The machine can automatically de-
tect the following sizes as standard
size copy paper:
Metric version A3L, A4L, A5L, 8" ×
13"L
Inch version
11" × 17"L, 8 1/2" ×
14"L, 81/2" × 13"L,
81/2" × 11"L, 51/2" ×
81/2" L
1. Paper guide release lever
❒ If you do not use standard size
copy paper, you should input ver-
tical and horizontal dimensions.
The sizes that you can input are as
follows:
C Lightly insert the copy paper face
down and adjust the paper
guides.
Metric version
•
Vertical: 90 –
305mm
•
Horizontal: 148 –
1,260 mm
Inch version
•
•
Vertical: 3.5" – 12"
Horizontal: 5.8" –
49.6"
Reference
For details about paper capacity of the
bypass tray, see P.13 “Copy Paper”.
1. Horizontal size
2. Vertical size
3. Extender
A Open the bypass tray.
4. Paper guides
Important
❒ If the guides are not flush with
the copy paper, a skew image or
paper misfeeds might occur.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Note
D Push down the paper guide re-
lease lever.
❒ Set the direction of the copy pa-
per to L.
“
Bypass” is selected automati-
cally.
❒ Swing out the extender to sup-
port paper sizes larger than
A4L, 81/2" × 11"L.
❒ Fan paper to get air between the
sheets and avoid a multi-sheet
feed.
2
When copying onto OHP
transparencies
A Lightly insert the OHP trans-
parencies face down and ad-
just the paper guide.
Note
❒ If you set A4, 81/2" × 11" or larg-
er copy paper, hold the edge of
the paper and push down the
paper guide release lever.
❒ If you do not push down the pa-
per guide release lever, a mis-
feed might occur.
Important
❒ The side of OHP transparen-
cies that is copied is fixed. Be-
fore you set the OHP
transparencies in the bypass
tray, check the cutting posi-
tion of the OHP transparen-
cies.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Bypass Tray
E Enter the vertical size of the pa-
per with the number keys, then
press the {OK} key.
When copying onto custom size
copy paper
Important
❒ You should specify the size of
copy paper to avoid paper mis-
feeds.
Note
2
❒
To change the number entered,
press the Clear/Stop key and
enter the new number.
A Press the {#} key.
{
}
When copying onto non-detected
standard size paper
Important
❒ You should specify the size of
paper to avoid paper misfeeds.
A Press the {#} key.
B Make sure that “1.Paper Size”
is displayed, then press the
{OK} key.
C Press the 0 or 1 key until
”Custom Size”is displayed,
then press the {OK} key.
D Enter the horizontal size of the
paper with the number keys,
then press the {OK} key.
B Make sure that “1.Paper Size”
is displayed, then press the
{OK} key.
Note
C Press the 0 or 1 key until
”Standard Size”is displayed
and press the {OK} key.
❒ To change the number en-
tered, press the {Clear/Stop}
key and enter the new
number.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
D Press the 0 or 1 key until the
desired size is displayed, then
press the {OK} key.
2
When copying onto envelopes
Note
❒ Use envelopes approximately
100mm, 4” wide.
A Press the {#} key.
B Press the 1 key to select ”2. Pa-
per Type”, then press the {OK}
key.
C Press the 0 or 1 key until
“Special” the desired paper
type is displayed, then press
the {OK} key.
E Set your originals, then press the
{Start} key.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Other Functions
C Press the
0
or
1
key until
User Codes
“12Key Op. Tools” is displayed,
then press the {OK} key.
When user codes are turned on, oper-
ators must input their user codes be-
fore the machine can be operated. The
machine keeps count of the number
of copies made under each user code.
2
D Press the 0 or 1 key until “7.Pro-
gram User Code” is displayed,
then press the {OK} key.
Note
❒ When user codes are turned on,
the machine will prompt you for
your user code after the power
switch is turned on or System Re-
set comes into effect.
❒ To prevent others from making
copies using your user code, press
the {Clear Modes} and {Clear/Stop}
keys simultaneously after copying.
E Enter the desired user code with
the number keys, then press the
{OK} key.
Reference
For details about user codes, see
P.62 “Settings You Can Change with
the User Tools”.
Auto Start
If you press the {Start} key during the
warm-up period, the {Start} key will
blink and your copies will be made as
soon as warm-up finishes.
Setting the User Code
A Press the {User Tools/Counter} key.
A Make any adjustments to copy
settings during the warm-up peri-
od.
B Set your originals.
C Press the {Start} key.
The {Start} key indicator alternate-
ly flashes red and green.
Note
B Press the 0 or 1 key to display
“3.Copier Features”, then press
the {OK} key.
❒ To cancel Auto Start, press the
{Clear/Stop} key.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Preset Reduce/Enlarge
You can select a preset ratio for copying.
❖ Inch version
Ratio (%)
Original →Copy paper size
155 (enlarge 51/2" × 81/2"→81/2" × 14"
area by 2)
2
129
121
93
81/2" × 11"→11" × 17"
81/2" × 14"→11" × 17"
A little reduced. (Create
Margin)
78
65
81/2" × 14"→81/2" × 11"
11" × 17"→81/2" × 11"
11" × 17"→51/2" × 81/2"
50 (reduce
Note
area by 1/4)
❒ You can select one of 7 preset ratios (3
enlargement ratios, 4 reduction ratios).
A
Press the
{
Reduce
}
or {Enlarge} key.
❒ You can change the preset ratios to
other ratios you frequently use. See
“4.Set Ratio” in P.62 “Copier Fea-
tures”.
❒ You can select a ratio regardless of
the size of an original or copy pa-
per. With some ratios, parts of the
image might not be copied or mar-
gins will appear on copies.
❒ Copies can be reduced or enlarged
as follows:
❖ Metric version
1. Reduce key
Ratio (%)
Original → Copy paper size
2. Enlarge key
200 (enlarge A5→A3
area by 4)
141 (enlarge A4→A3, A5→A4
area by 2)
122
93
8”× 13”→A3, A4→B4JIS
A little reduced. (Create
Margin)
82
8”× 13”→A4, B4JIS→8”×
13”
B
Press the
sired reduce/enlarge size is displayed.
0
or
1
key until the de-
71 (reduce
A3→A4, A4→A5
area by 1/2)
C Press the {OK} key.
50 (reduce
A3→A5, F→A5
area by 1/4)
D Set your originals, then press the
{Start} key.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom
Zoom
You can change the reproduction ra-
tio in 1% steps.
B Enter the ratio.
When using the 0 or 1 key
A Enter the desired reproduction
2
ratios with the 0 or 1 key.
When using the number keys
Note
A Enter the desired ratio with the
❒ You can change the reproduction
ratio from 50–200 %.
number keys.
Note
❒ You can select a ratio regardless of
the size of an original or copy pa-
per. With some ratios, parts of the
image might not be copied or mar-
gins will appear on copies.
❒ To change the ratio entered,
press the {Clear/Stop} key
and enter the new ratio.
C Press the {OK} key.
❒ You can select a preset ratio which
is near the desired ratio, then ad-
just the ratio with the 0 or 1 key.
D Set your originals, then press the
{Start} key.
A Press the {Zoom} key.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Combine
The optional 16MB copier memory unit is required for Type 1 to use this function .
Use this feature to combine several
original images onto one or more
pages.
• Originals reading from top to bot-
tom
2
❖ 1sided 2 pages→Combine 1 Side
Limitation
❒ You cannot use the bypass tray
with this function.
❒ The machine cannot copy originals
different in size and direction.
Note
❖ 1sided 4 pages→Combine 1 Side
❒ The number of originals copied
(combined) can be 2 or 4.
❒ In this mode, the machine selects
the reproduction ratio automati-
cally. This reproduction ratio de-
pends on the copy paper sizes and
the number of originals.
❒ You can change the reproduction
ratio from 50-200 %.
❒ If the calculated ratio is under the
minimum ratio, it is corrected
within the range of the ratio auto-
matically. However, with some ra-
tios, parts of the image might not
be copied or blank margins appear
on copies.
❖ Setting originals (Originals set in the
document feeder)
• Originals reading from left to
right
❒ Even if the direction of originals is
different from that of the copy pa-
per, the machine will automatical-
ly rotate the image by 90° to make
copies properly. (When the Auto
Reduce/Enlarge function is select-
ed)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
❒ When the number of originals
placed is less than the number
specified for combining, the last
page(s) will be copied blank as
shown in the illustration.
B Make sure that “Combine”is se-
lected, then press the {OK} key.
C Press the 0 or 1 key until the de-
sired combine mode is displayed,
then press the {OK} key.
2
❒ Direction of the originals and ar-
rangement of combined images.
D Press the {Select Paper Tray} key to
select the copy paper.
❖ Portrait (K) originals
E Set your originals.
When setting an original on the
exposure glass or in the
document feeder
A Set the original, then press the
{Start} key.
❖ Landscape (L) originals
B Set the next original, then
press the {Start} key.
Note
❒ To finish copying, press the
{#} key to eject the copy.
When setting a stack of originals
in the document feeder
A Press the {Combine/Series} key.
A Set your originals, then press
the {Start} key.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Series Copies
The optional 16MB copier memory unit is required for Type 1 to use this function .
You can make one-sided copies from
two facing pages of bound (book)
originals.
❖ Inch version
Original
Copy paper
11" × 17"L
2
81/2" × 11"K × 2
sheets
❖ Book→1 Sided
You can make one-sided copies
from two facing pages of a bound
original (book).
81/2" × 11"L
51/2" × 81/2"K × 2
sheets
A Press the {Combine/Series} key.
Limitation
❒ You cannot use the bypass tray
with this function.
Book→1 Sided
You can make 1–sided copies from 2
facing page of a bound original
(Book).
B Press the 1 key to select “Series”,
then press the {OK} key.
Note
❒ Refer to the following table when
you select original and copy paper
sizes with a ratio of 100%:
C Make sure that “Book→1 Sided”is
selected, and press the {OK} key.
❖ Metric version
Original
A3L
Copy paper
D Select the paper by pressing the
{Select Paper Tray} key until the
paper you require is displayed.
A4K× 2 sheets
B5JISK × 2 sheets
A5K × 2 sheets
B4JISL
A4L
E Set your originals, then press the
{Start} key.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Combination Chart
Combination Chart
The combination chart given below shows which modes can be used together.
When you read the chart, please refer to the following table.
✩
means that these modes can be used together.
→
means that these modes cannot be used together. The mode after
you select will be the mode you're working in.
2
×
means that these modes cannot be used together. The mode before
you select will be the mode you're working in.
The following shows the combinations of functions.
Mode after you select
Mode before you select
Non-standard Originals
Original Type Selection
Auto Paper Select
Auto Reduce/Enlarge
Sort
--
✩
--
×
✩
✩
→
--
✩
✩
✩
✩
--
✩
✩
→
×
✩
✩
✩
→
✩
×
✩
✩
→
✩
✩
×
✩
✩
→
✩
✩
×
✩
✩
→
→
✩
×
✩
×
✩
--
×
✩
✩
✩
✩
✩
✩
✩
✩
✩
✩
✩
✩
✩
✩
→
✩
×
✩
×
✩
--
Copying From The Bypass Tray
Zoom
✩
✩
✩
✩
→
✩
×
✩
×
--
→
--
→
→
→
✩
→
--
Combine
✩
✩
Series Copies
Book → 1-sided
×
×
→
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
2
42
Download from Www.Somanuals.com. All Manuals Search And Download.
|