R
Portland
Oregon USA
Tested and
Listed by
Model:
O-T L
EDGE™ 60
ZERO CLEARANCE PELLET FIREPLACE
C
US
OMNI-Test Laboratories, Inc.
EDGE60
Owner’s Manual - Installation and Operation
Tuscan
Studio
Natural
Curved
NOTICE
DO NOT DISCARD THIS MANUAL
DO NOT
DISCARD
•
Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
•
Leave this manual with
party responsible for use
and operation.
• Important operating and
maintenance instruc-
tions included.
WARNING
WARNING
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND
cool down.
Hot glass will cause burns.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
•
•
•
•
Do not touch glass until it is cooled
NEVER allow children to touch glass
Keep children away
CAREFULLY SUPERVISE children in same room
as fireplace.
• Do not overfire - If any external part starts to
glow, you are overfiring. Reduce flame height
(feed rate). Overfiring will void your warranty.
•
Alert children and adults to hazards of high
temperatures.
• Comply with all minimum clearances to com-
bustibles as specified. Failure to comply may
cause house fire.
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other
flammable materials away.
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies recommends NFI certified
professionals, or technicians supervised by an
NFI certified professional.
CAUTION
Tested and approved for wood pellets, shelled field
corn, wheat and black oil sunflower seeds. Burning
of any other type of fuel voids your warranty.
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Safety Alert Key:
!
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates practices which may cause damage to the fireplace or to property.
TABLE OF CONTENTS
Congratulations ...............................................................2
Sample of Safety/Serial Numer Label .............................2
Safety Alert Key...............................................................3
Limited Warranty .............................................................4-5
Section 6: Framing & Clearances
A. Recommended Locations ................................26
B. Hearth Extension...............................................26
C. Sealing at Penetration of Building Envelope.....27
D. Frame the Fireplace .........................................27
E. Construct a Chase ............................................28
F. Finishing Material..............................................29
G. Door Opening Clearances.................................30-31
H. Combustible Mantel & Fuel Loading Clearance..32
Section 1: Listing and Code Approvals
A. Appliance Certifications.....................................6
B. Mobile Home Approved.....................................6
C. Glass Specifications..........................................6
D. Electrical Rating................................................6
E. Outside Air Required.........................................6
F. BTU & Efficiency Specifications........................6
I.
Non-Combustible Materials...............................33
J. Combustible Materials.......................................33
Section 7: Installation of Fireplace
User’s Guide
Section 2: Operating Instructions
A. Position the Fireplace........................................34
B. Sub-Floor Material & Securing Fireplace..........34
C. Junction Box and Wiring Diagram.....................35
D. Connecting Wall Control to Fireplace................35
E. Thermostat Wall Control Installation.................35
F. Flue Collar Installation.......................................36-37
A. Fire Safety.........................................................8
B. Combustible/Non-Combustible Material............8
C. Fuel Material & Fuel Storage ............................8-9
D. General Operation Information..........................9
E. Power Switch ....................................................9
F. Before Your First Fire........................................9
G. Filling the Hoper with Fuel.................................10
H. Starting Your First Fire......................................10
Ignition Cycles...................................................10-11
J. Fire Characteristics & Flame Height
Adjustment........................................................12
K. Battery Back-Up System...................................12-13
L. Clear Space ......................................................13
Section 8: Vent Information
A. Venting Termination Requirements...................38
B. Avoiding Smoke and Odors ..............................39
C. Negative Pressure.............................................40
D. Draft ..................................................................40
E. Chimney & Exhaust Connection .......................41
F. Equivalent Feet of Pipe.....................................41
G. Pipe Selection Chart .........................................42
H. Outside Air Locations & Considerations............43
I.
Section 3: Maintaining & Servicing Appliance
A. Proper Shutdown Procedures...........................14
B. Quick Reference Maintenance Chart................14
C. High Ash Fuel Content Maintenance ................15
D. Accessing Components for Maintenance..........15
E. General Maintenance & Cleaning.....................16-20
I.
Outside Air Installation......................................44
J. Vertical, Interior, Typical Installation .................45
K. Through the Wall & Vertical, Exterior................45
L. Through the Wall...............................................46
Section 9: Mobile Home Installation..................47
Section 10: Appliance Set-Up
Section 4: Troubleshooting for Homeowner
A. Frequently Asked Questions .............................21
B. Wall Control Error Messages ............................22
A. Log Set Placement............................................48
B. Front Installation Instruction..............................49
Section 11: Replacement Parts
Installer’s Guide
Section 5: Getting Started
A. Glass Replacement...........................................50
B. Combustion (Exhaust) Blower ..........................50
C. Convection Blower............................................51
D. Baffle Removal & Replacement........................51
A. Design, Installation & Location
Considerations and Floor Support ....................23
B. Locating Your Thermostat Wall Control............24
C. Tools & Supplies Needed..................................24
D. Inspect Appliance and Components .................24
E. Checklist to Help Determine Location...............24
F. Recommended Sequence of Installation .........25
G. Items to Verify During Test Burn.......................25
Section 12: Troubleshooting for Installers ........52
Section 13: Reference Materials
A. Fireplace Dimensions........................................53
B. Component Functions.......................................54-55
C. Component Locations.......................................56
D. Exploded Drawings...........................................57
E. Service Parts & Accessories.............................58-62
F. Service & Maintenance Log..............................63
G. Contact Information...........................................64
Page 3
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Page 4
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Page 5
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Listing and Code Approvals
1
A. Appliance Certification
F. BTU & Efficiency Specifications
Model
EDGE™ 60 Pellet Fireplace
OMNI Test Laboratories, Inc.
061-F-75-6.2
Laboratory
Report No.
Type
Emissions Rating: EPA Compliance
BTU Input*:
Efficiency:
14,620 - 52,000 / hr
83.3%
Solid Fuel Room Heater/Pellet Type
Standard
ASTM E1509-04, ULC S627-00 and
ULC/ORD-C1482 Room Heater Pellet
Fuel Burning type and (UM) 84-HUD,
Mobile Home Approved.
Heating Capacity: 2,400 - 3,800 square feet depend-
ing on climate zone
Hopper Capacity: 120 lbs
Fuels:
Pellets, Shelled Field Corn, Wheat
FCC
Complies with Part 15 of FCC Rules.
Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that
may cause undesired operation.
and Black Sunflower Seeds
450 lbs (empty hopper)
add approximately 120 lbs
Shipping Weight:
Weight with Full
Hopper:
*BTU will vary, depending on the type of fuel you use in
your fireplace. Consult your Quadra-Fire dealer for best
results.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
ASTM E1509-04, ULC S627-00, (UM) 84-HUD and
ULC/ORD-C-1482.
WARNING! Risk of Fire! Hearth & Home Technologies dis-
claims any responsibility for, and the warranty and agency
listing will be voided by the below actions.
DO NOT:
• Install or operate damaged appliance
• Modify appliance
B. Mobile Home Approved
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is used.
• Install other than as instructed by Hearth & Home
Technologies
• Operate the appliance without fully assembling all
components
The structural integrity of the mobile home floor, ceiling, and
walls must be maintained.
• Overfire
• Install any component not approved by Hearth &
Home Technologies
The appliance must be properly grounded to the frame of
the mobile home and use only Listed pellet vent Class “L”
or “PL” connector pipe.
• Install parts or components not Listed or approved.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
A Quadra-Fire Outside Air Kit must be installed in a mobile
home installation. You must order the Outside Air Kit sepa-
rately.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
Note: The appliance is also approved for installation
into a shop.
NOTICE: Hearth & Home Technologies, manufacturer
of this appliance, reserves the right to alter its prod-
ucts, their specifications and/or price without notice.
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
Quadra-Fire is a registered trademark
of Hearth & Home Technologies.
D. Electrical Rating
115 VAC, 60 Hz, Start 5 Amps, Run 1.25 Amps
E. Outside Air Kit
Outside Air is required on all installations. You must order
the Outside Air Kit separately.
Page 6
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
User’s Guide
Operating Instructions
2
WARNING
HOT SURFACES!
Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns.
•
•
•
•
•
Do not touch glass until it is cooled
NEVER allow children to touch glass
Keep children away
CAREFULLY SUPERVISE children in same room as fireplace.
Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable materials.
Keep clothing, furniture, draperies and other flammable materials away.
•
WARNING! Do not operate appliance before reading and
understanding the operating instructions in both of the
Owner’s and Thermostat Wall Control manuals. Failure to
operate appliance according to operating instructions could cause
fire or injury.
CAUTION
Use only approved fuel. This unit was tested and
approved for wood pellets, shelled field corn, wheat
and black oil sunflower seeds. Burning of any other
type of fuel voids your warranty.
Page 7
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
A. Fire Safety
Shelled Field Corn
• Must be 15% or less moisture content.
• Must be clean and free from debris
• Never burn corn straight from the field
To provide reasonable fire safety, the following should be
given serious consideration:
• Install at least one smoke detector and CO monitor on each
floor of your home.
• Stalk parts, excessive fines and cob remnants, etc. will
clog the auger mechanism
• Corn with excessive grain dust must be screened by sifting
with 3/16 inch (4.7mm) mesh screening
• Locate detectors away from the heating appliance and close
to the sleeping areas.
CAUTION! Do not burn fuel that contains an additive;
(such as soybean oil).
• Follow the detector’s manufacturer’s placement and
installation instructions and maintain regularly.
• May cause hopper fires
• Damage to product may result
• Conveniently locate a Class A fire extinguisher to contend
with small fires.
Read the ingredients list on the package. If you are buying
corn or wheat the only ingredient that should be listed is
corn or wheat.
•
In the event of a hopper fire:
• Evacute the house immediately.
• Notify fire department.
WARNING! Risk of Chemical Poisoning!
Do NOT burn treated seed corn
• Chemical pesticides are harmful or fatal if swallowed
• Burning treated seed corn will void your warranty
B. Combustible/Non-Combustible Materials
•
Combustible Material
Material made of or surfaced with wood, compressed
paper, plant fibers, plastics, or any material capable
of igniting and burning, whether flame-proofed or not,
plastered or unplastered.
Clinkers
Minerals and other non-combustible materials such as sand
will turn into a hard, glass-like substance called a clinker when
heated in the firepot.
•
•
Non-combustible Material
Trees from different areas will vary in mineral content. That
is why some fuels produce more clinkers than others.
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, slate,
glass or plasters, or any combination thereof.
Moisture
Non-combustible Sealant Material
Always burn dry fuel. Burning fuel with high moisture content
takes heat from the fuel and tends to cool the appliance,
robbing heat from your home. Damp pellet fuel can clog the
feed system.
Sealants which will not ignite and burn: Rutland, Inc.
Fireplace Mortar #63, Rutland 76R, Nuflex 304, GE
RTV106 or GE RTB116 (or equivalent).
Size
C. Fuel Material and Fuel Storage
•
Pellets are either 1/4 inch or 5/16 inch (6-8mm) in diameter
Pellet fuel quality can greatly fluctuate. The EDGE 60
appliance has been designed to burn a wide variety of fuels,
giving you the choice to use the fuel that is most economical
in your region.
• Length should be no more that 1-1/2 inches (38mm)
• Pellet lengths can vary from lot to lot from the same
manufacturer
• Due to length variations, the flame height (feed rate) may
need adjusting occasionally. See page 12 for instructions.
Hearth & Home Techonologies strongly recommends only
using Pellet Fuel Institute (PFI) certified fuel.
Performance
Fuel Material
• Higher ash content requires the ash drawer to be emptied
more frequently
• Hardwoods require more air to burn properly
• Set wall control to “Utility Pellet” if the firepot and ash pan
are filling quickly. This will cause the auto-clean system
to empty the firepot more often.
•
•
•
Made from sawdust or wood by-products
Shelled field corn & other biomass fuels
Depending on the source material it may have a high or
low ash content.
Higher Ash Content Material
• Premium wood pellets produce the highest heat output.
• Burning pellets longer than 1-1/2 inches (38mm) can cause
an inconsistent fuel feed rate and/or missed ignitions.
•
•
•
Hardwoods with a high mineral content
Fuel that contains bark
Standard grade pellets, high ash pellets, corn and other
biomass fuels
We recommend that you buy fuel in multi-ton lots whenever
possible. However, we do recommend trying various brands
before purchasing multi-ton lots to ensure your satisfaction.
Lower Ash Content Material
•
•
•
Softwoods
Fuels with low mineral content
Premium grade pellets
Page 8
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
CAUTION! Tested and approved for wood pellets, shelled
field corn, wheat and black oil sunflower seeds. Burning of
any other type of fuel voids your warranty.
2. Thermostat Wall Control - Manual Setting
When you select “Manual” on theAUTO/MANUALscreen the
appliance will still automatically turn on and off according to
the temperature setting.
Changing to Different Fuel Type
However, you will be able to manually control the heat output
levels. Adjust the heat output levels by using the HEAT
OUTPUT LEVEL screen. Figure 9.2.
• Empty the hopper of the previous fuel
•
Thoroughly vacuum hopper before filling with the new
fuel
• Select the appropriate setting on the FUEL SELECTION
screen on the thermostat wall control
Medium
The burn rate, BTU content and heat output will all vary
depending on the fuel selected.
Storage
Figure 9.2
• Wood pellets should be left in their original sealed bag
until using to prevent moisture absorption.
3. Auto-Clean Firepot System
Your appliance is equipped with an automatic firepot cleaning
system that will change the frequency of cleaning based on
the fuel being burned.
• Shelled corn, wheat or sunflower seeds should be stored
in a tight container to prevent it from absorbing moisture
from damp or wet floors.
The auto-clean system will clean itself immediately on initial
plug in. If there is a power outage, as soon as power is
restored it will recycle and clean itself if there is no fire in the
firepot.
• This will also prevent rodents from becoming a problem
.
• Do not store any pellet fuel within the clearance
requirements or in an area that would hinder routine
cleaning and maintenance.
NOTE: User is responsible for removing the ash from the
ash drawer.
D. General Operating Information
E. Power Switch
Read and understand the Thermostat
Wall Control manual for detailed operating
instructions. The wall control is an intregal
part of how to operate this appliance.
The power switch is located at the bottom right hand corner of
the fireplace. It turns the power on and off to the fireplace.
Before servicing the fireplace this power switch must be in
the off position. When the power switch is OFF there will be
no display on the wall control screen.
1. Thermostat Wall Control - Automatic Setting
The appliance is like most modern furnaces; when the
thermostat wall control calls for heat, your appliance will
automatically light and deliver heat.
Power Switch
When the room is up to temperature and the wall control is
satisfied the appliance will shut down.
Power
Switch
= ON
I
In the automatic setting the heat output level is controlled by
the wall control. Select “Automatic” on the AUTO/MANUAL
screen. Figure 9.1.
0
= OFF
Figure 9.3
F. Before Your First Fire
Automatic
Manual
Off
•
•
•
First, make sure your appliance has been properly installed
and that all safety requirements have been met.
Pay particular attention to the fire protection, venting and
thermostat wall control installation instructions.
Double check that the ash pan, hopper and firebox are
empty and then close the firebox door.
Figure 9.1
NOTICE: The tip of thermocouple must be in contact with the
inside end of the thermocouple cover or missed ignitions can
occur.
Page 9
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
G. Filling the Hopper with Fuel
3. Automatic or Manual Setting
•
Check the hopper and make sure it is empty before filling
with fuel.
The automatic setting will control the heat output based on
the comfort level selection. The manual setting allows you to
manually control the heat output settings.
•
Open the front to expose the hopper door. Pull down on the
hopper door to open and fill with fuel. The hopper door can
now serve as a shelf to support the bag of fuel
I. Ignition Cycles
•
•
Do not over fill the hopper. The hopper door must be com-
pletely closed to maintain proper vacuum and for the feed
motor to operate. An error ICON will appear on the wall
control if the hopper door is not properly closed.
The fireplace engine is controlled by the digital thermostat
wall control. The digital display on the wall control will tell
you what your appliance is doing in the upper left corner
(System Status). Figure 10.3.
Do not leave any part of the fuel bag on the appliance after
filling hopper.
System Status
NOTICE: RAISED PLATFORM INSTALLATIONS
12:30 PM
Set at: 73
READY
Consideration must be given for filling the hopper with fuel
when determining the height of the raised platform. It must
not be so high that it interferes with the safety of filling the
hopper with fuel.
73
MENU
HEAT OUTPUT
Figure 10.3
H. Starting Your First Fire
1. Fuel Selection
Every time the thermostat calls for heat, the appliance steps
through five cycles:
To start your first fire, you must:
• Select the appropriate fuel on the FUEL SELECTION screen
on the thermostat wall control to match the fuel you have
chosen to burn.
1
2
3
Start-Up Cycle
Soft-Start Cycle
Heating Cycle
4 Shutdown Cycle
5 Auto-Clean Cycle
• If the proper fuel is not selected your appliance will not
operate properly.
The duration and characteristics of these cycles may be dif-
ferent with each type of fuel selected.
• For example, if you have selected wood pellets and you are
burning corn, the appliance may not light, it may go out or
overfeed. Figure 10.1.
WARNING! RISK OF FIRE!
NOTE: If you are lighting your appliance for the first time:
Do NOT operate appliance:
• With appliance door open
• With firepot floor open
• With ash pan removed
• Without the two slide rail attachment bolts secured to
fireplace
•
The feed tube will be empty and it can take some time to fill
it with fuel before you will see a fire
•
Put a handful of fuel in the firepot (priming) to speed up the
process. You can also do this when you have run com-
pletely out of fuel.
FUEL SELECTION
Corn
Utility Pellet
Softwood Pellet
Sunflower Seeds
1. Start-Up Cycle
Wheat
Hardwood Pellet
During this cycle:
DONE
SELECT
• Igniter turns on for 90 seconds to heat up the air in the
firepot
Figure 10.1
• Combustion blower starts
• Vacuum switch comes on
2. Comfort Level Selection
Once your fuel is selected, select the temperature at the desired
setting on the SET COMFORT LEVEL screen. Figure 10.2.
• Feed motor turns on adding fuel to the firepot and the
appliance waits for the fire to start
The duration of start-up depends on the type and quality
of fuel used. It is normal to see some smoke during the
ignition process as moisture evaporates and the fuel lights.
The smoke will stop once the fire starts.
Figure 10.2
Page 10
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
5. Auto-Clean Cycle
2. Soft Start Cycle (SS-Low / SS-Med)
The firepot auto-clean system will cycle:
• When the appliance is first plugged in
Once the fire is lit:
• The appliance moves into the low soft-start cycle as it
continues to build the fire
• When the house reaches temperature and the appliance
shuts down
• More fuel will be added
• At prescribed intervals, depending on the type of fuel se-
lected
• As the fire builds, the appliance will change to medium
soft-start mode
• When starting up after an electrical interruption
• The heating cycle begins
If your appliance is running and the auto-clean cycle is initi-
ated, the appliance will revert to shutdown cycle.
3. Heating Cycle ( Auto / Man - L, ML, M, MH, H)
• The floor of the firepot will open and dump the ash into
the ash pan
There are two choices in the Automatic / Manual menu of
how your appliance will operate:
• It takes approximately 2 minutes to complete the auto-
clean cycle
Automatic Mode
• The floor will then shut, and if the thermostat is still call-
ing for heat, the fire will start again
• The wall control will turn the heat output level up or down
depending on how far the room temperature is from the
desired temperature
• During this auto-clean cycle, the convection blower may
continue to run. The combustion blower will continue to
run.
• The digital display will read AUTO:M, i.e. automatic-me-
dium level
• As the room temperature approaches the desired tem-
perature, the appliance will turn down to lower settings
Additional Screen Messages:
READY It is telling you that the home is up to temperature
and doesn’t need any heat.
• When the home reaches your set temperature, the appli-
ance will go into the shutdown cycle
- - - - - The screen will show 5 dashes when the wall
control and the control board are NOT communicating with
each other. Check that the wiring on the thermostat is prop-
erly connected.
Manual Mode
• Set the heat output setting from the main screen
• The right bottom button will read HEAT OUTPUT
• You can operate the appliance from any of the 5 levels
MAINTENANCE BURN This indicates the appliance is
operating on battery backup, prior to the auto-clean. The
maintenance burn will keep the system from shutting down
as the appliance will not automatically re-light in battery
back-up mode.
• On the lowest level (MAN: L) the appliance will stay on
longer, burn less fuel per hour, and will take longer to
bring the home up to your desired temperature
• On the highest setting (MAN:H) the appliance will burn
more fuel per hour, and bring your home up to tempera-
ture more quickly
OFF The AUTO/MANUAL SETTING screen has been set
to OFF. Set the appliance to OFF when performing periodic
maintenance to prevent an unexpected startup.
•
In Manual mode the heat output does not change but
will stay at the setting you chose until the comfort level
is reached (meaning the thermostat has been satisfied).
Turn to OFF to stop operation.
BLANK SCREEN The ON/OFF switch may in OFF posi-
tion. Turn to ON position.
4. Shutdown Cycle
Once your home has reached your set temperature:
CAUTION
• Appliance will stop feeding fuel and allow the fire to dimin-
ish
Tested and approved for wood pellets, shelled field
corn, wheat and black oil sunflower seeds. Burning
of any other type of fuel voids your warranty.
• Convection blower will continue to run until the appliance
cools to appropriate temperature
•
Appliance will begin the auto-clean cycle
Page 11
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Instructions to Hook Up to Battery Back-Up
J. Fire Characteristics and Flame Height
(Feed Rate) Adjustment
Open Front to expose battery plug on bottom left side of
fireplace. Plug in the battery. Figure 12.2. Be sure the bolts
securing the unit in place are installed and secured.
A properly adjusted fire will have an active flame pattern
and the flame will rise and fall somewhat. This is normal.
• On HIGH setting, the flame will extend approximately
203mm out of the firepot. If it is not 203mm tall, in-
crease the flame height.
Left Side
Firebox Door
• On MEDIUM or LOW setting the flame will be shorter.
Battery Plug In
• Reduce the flame height if the fire has tall flames with
black tails and seems somewhat lazy. This may also
indicate that the firepot and/or heat exchanger needs
to be cleaned. Refer to Section 3 for Maintenance and
Cleaning Instructions.
Ash Door
Figure 12.2
Adjusting the Flame Height (Feed Rate)
• Set your appliance to “MANUAL” mode on the wall
control.
Operating on Battery Back-Up
• A battery icon appears on your wall control to let you
know you are now operating on battery power. Figure
12.3
• Set the heat output level to HIGH.
• Adjust the flame height using the “FLAME HEIGHT
ADJUST” screen on the wall control. Figure 12.1.
• The fire must be manually lit as the appliance will no
longer automatically light. Follow the instructions in the
Wall Control Manual.
• Use only approved fire starting gel to start the fire.
• The high burn rate is no longer available on battery
back-up.
• Each level drops down one level, i.e the high burn be-
comes medium-high burn and so on.
Figure 12.1
• If the battery charge falls below 10 volt it can no longer
sustain the appliance operation and the appliance will
shut down. You must disconnect and reconnect the bat-
tery to start it up again.
K. Battery Back-up System (Optional)
CAUTION!
• Hook up to battery terminals BEFORE you plug battery
into appliance.
Recommended Battery
• 12 volt deep cycle battery, (i.e., marine or RV type).
• Damage to internal electronic components may occur.
• A 12 volt battery cable is available through your local
dealer.
The appliance has been designed to operate on an optional
battery back-up system.
If you have frequent power outages in your region, hook
the appliance up to a 12 volt battery and it will automatically
switch to battery power in the event of a power failure. The
12 volt power cord, sold as a separate accessory, does not
charge the battery.
Battery
Below
13 Volts
12 Volts
11 Volts
10 Volts
WARNING! Risk of Injury!
Figure 12.3
• Do not operate in the battery back-up mode with the
appliance pulled out on the slide rails.
• Blowers may continue to run and would be exposed to
human contact.
Page 12
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
K. Battery Back-up System (Cont’d)
Wall Control Display
The wall control will display the battery icon when operating in
the battery back-up mode. Figure 13.1.
“Maint Burn” will display when
the thermostat has reached the
set room temperature and will
run on low until it reaches its
auto-clean cycle time.
MAINT BURN
12:30 PM
Set at: 73
73
MENU
HEAT OUTPUT
Battery icon.
Figure 13.1
L. Clear Space
WARNING! RISK OF FIRE! Do NOT place combustible
objects in front of the appliance. High temperatures may
ignite clothing, furniture or draperies. Maintain a minimum
clearance of 3ft in front of appliance.
Mantel: Avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these
objects.
NOTICE: Clearances may only be reduced by means ap-
proved by the regulatory authority having jurisdiction.
WARNING! RISK OF FIRE! Keep combustible materials,
gasoline and other flammable vapors and liquids clear of
appliance.
• Do NOT store flammable materials in the appliance’s
vicinity.
• Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids to start or “freshen up” a fire
in this heater.
Keep all such liquids well away from the heater while it is in
use as combustible materials may ignite.
Page 13
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Maintaining & Servicing Your Appliance
3
A. Proper Shutdown Procedure
Before Servicing Your Appliance
• Set wall control to OFF on AUTOMATIC / MANUAL SET-
CAUTION! SHOCK AND SMOKE HAZARD!
TING screen. Figure 14.1.
• Proper Shutdown Procedure must be followed.
• Wall control screen will scroll through the following mes-
sages after setting to OFF.
• Smoke spillage into room can occur if appliance is not
cool before turning off power switch.
• Shutdown
• Auto-Clean
• Off
• Risk of shock if appliance is not turned off before servic-
ing appliance.
Approximately 45 minutes after setting the wall control to
OFF, the appliance should be cool enough to touch. If so,
now you can turn the power switch to OFF and pull the
appliance foward on the rails.
Automatic
Manual
Off
There is an interlock switch next to the power switch that as
you slide the appliance out it will ensure the auto-clean system
and the auger will not run, but the blowers will operate.
After servicing, restart with the AUTO/MANUAL SETTINGS
screen. Figure 14.1.
Figure 14.1
Follow the detailed instructions found in this
section for each step listed in the chart below.
B. Quick Reference Maintenance Chart
Cleaning or Inspection
Frequency
Daily Weekly Every 2 Monthly Yearly
Weeks
Ash Pan - Burning Wood Pellets
Ash Pan - Burning Alternate Fuels
Ash Removal from Firebox
Every 5 bags of fuel
Every 1 bag of fuel
OR
OR
X
X
More frequently depending on the OR
fuel type or ash build-up
X
Auto-Clean Inspection
Blower, Combustion (Exhaust)
Blower, Convection
More frequently depending on the OR
fuel type
X
X
More frequently depending on the OR
fuel type
X
X
More frequently depending on the OR
operating environment
Door Latch Inspection
Prior to heating season
OR
OR
OR
OR
OR
OR
Firebox - Prepare for Non-Burn Season At end of heating season
X
Firepot - Burning Softwood Pellets
Firepot - Burning Hardwood Pellets
Firepot - Burning Alternate Fuels
Glass
Every 5 bags
Every 3 bags
Every 1 bag
X
X
X
When clear view of firepot
becomes obscured
X
Heat Exchanger & Drop Tube
Hopper
Every 1 ton of fuel
OR
X
Every 1 ton of fuel or when chang- OR
ing fuel types
X
Venting System
More frequently depending on the OR
fuel type
X
NOTICE: These are recommendations. Clean more frequently if you encounter heavy
build-up of ash at the recommended interval or you see soot coming from the
vent. Not properly cleaning your appliance on a regular basis will void your
warranty.
Page 14
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Pull fireplace toward you until
fully extended
C. High Ash Fuel Content Maintenance
•
Frequency: When the ash build-up exceeds the half
way point in the firepot
•
By: Homeowner
If the ash build-up exceeds the half way point in the firepot
before it automatically cleans, then the firepot is not being
cleaned often enough.
Another symptom is if clinkers are adhering to the sides of
the firepot.
Slide Rails
Double check the wall control to ensure the proper setting
has been selected for the fuel you are burning. If that is cor-
rect, change the setting to “Utility Pellet”.
NOTE: You will need to empty the ash pan more fre-
quently if using the “Utility Pellet” setting.
Figure 15.3
WARNING! Risk of Fire and Smoke!
Attachment brackets shown in open position.
Fireplace is not secure and can roll forward
on the rails. Also the exhaust gaskets are
not sealed properly and combustion leakage
will occur.
• High ash fuels or lack of maintenance can cause firepot to
overfill. Follow proper shutdown procedure if ash buildup
exceeds half way point in firepot.
• Failure to do so could result in smoking, sooting and pos-
sible hopper fires.
Brackets separated
Pellets Back-Up
in Feed Tube
Firepot Overfills
Figure 15.4
Ash Build-Up in Firebox
Attachment brackets are tightly fastened to one another so
fireplace is secure and will not roll forward on the rails. It also
ensures the exhaust gaskets are sealed properly to prevent
combustion leakage.
Figure 15.1
D. Accessing Components for Maintenance
1. Follow the proper shutdown procedure found on page 14.
2. Remove the Front. Lay it on a soft surface to prevent
scratching.
3. Remove both bolts located on each lower side of the fire-
place with a Phillips head screwdriver or socket wrench
and set aside. Figure 15.2.
4. Pull the fireplace towards you until fully extended. Figure
15.3.
Figure 15.5
One bolt located on each side of fireplace
5. Components are now exposed for service.
6. Slide the fireplace back into the outer can. Re-attach the
bolts ensuring that the attachment brackets are securely
fastened. This will prevent the fireplace from unexpect-
edly sliding out on the rail system. Figures 15.4 and
15.5.
7. Double check the bolts and brackets are correctly
positioned to ensure the exhaust gaskets are prop-
erly sealed to prevent combustion leakage.
Figure 15.2
Page 15
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
2. Cleaning Ash Pan
E. General Maintenance and Cleaning
•
Frequency: Wood Pellets: Weekly or every 3-5 bags
Alternate Fuel: Daily or every 1 bag
By: Homeowner
1. Auto-Clean System Inspection & Cleaning
•
•
Frequency: Monthly or every ton (aprx. 50 bags) or
more frequently depending on the type of fuel
By: Homeowner
a Locate the ash pan underneath the firepot.
b. Slide the ash pan straight out.
•
c. Empty into a non-combustible container and re-install ash
pan.
a. Be sure the wall control screen says OFF, the appliance
is allowed to cool and the power switch is in the OFF
position.
d. When replacing ash pan push it back until it catches on
the 2 side latches.
b. Open the Front and firebox door. Inspect the auto-clean
springs: (See item #33 on Figure C on page 57 for the e. Clinkers filling the ash pan will have to be cleaned out
location of the springs).
more often than ash. See Disposal of Ashes.
3. Disposal of Ashes
• Inspect for any degradation or deformation
•
•
Frequency: As needed
By: Homeowner
• As the springs heat up and cool down they can lose
tension
a. Ashes should be placed in a metal container with a tight-
fitting lid.
• If there is a gap showing above the firepot bottom,
approximately 1/16 inch (1.59mm) or more, it means
the springs have lost their tension
b. The closed container of ashes should be placed on a
non-combustible floor or on the ground, well away from
all combustible materials, pending final disposal.
• Lost tension can not keep the floor in the proper
position causing ignition problems and fuel falling
into the ash pan.
c. If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have been thoroughly cooled.
• Call your dealer to replace the springs.
c. Inspect the holes in the firepot floor for any debris.
• The holes must be kept clear.
WARNING! RISK OF FIRE! Keep combustible materials,
gasoline and other flammable vapors and liquids clear of
appliance.
• Burning corn will cause the holes to fill with particles
and will need to be removed.
• Do NOT store flammable materials in the appliance’s
d. How often the firepot cleans itself depends on:
vicinity.
• The type of fuel you selected on the thermostat wall
control
• Never use gasoline, gasoline-type lantern fuel, kerosene
charcoal lighter fluid or similar liquids to start or “freshen
up” a fire in this heater.
• How long the apliance burns before satisfying set point
on the the wall control.
Keep all such liquids well away from the heater while it is in
use as combustible materials may ignite.
• Burning biomass fuels may require a more thorough
cleaning during the burn season.
e. Excessive clinkers will eventually jam the auto-clean
system and generate an error message on the wall
control.
WARNING! RISK OF FIRE!
Do NOT store fuel:
• Closer than required clearances to combustibles to ap-
pliance.
• Within space required for loading or ash removal.
WARNING
Handle glass doors with care.
•
Inspect the gasket to ensure it is
undamaged.
•
•
Do NOT strike, slam or scratch glass.
Do NOT operate appliance with glass door
removed, cracked, broken or scratched.
Figure 16.1
Page 16
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
4. Cleaning Heat Exchanger, Drop Tube & Exhaust
•
Frequency: Monthly or every 1 ton of fuel (aprx. 50
bags).
•
By: Homeowner
NOTE: There are heavy duty vacuum cleaners specifically
designed for solid fuel appliance cleaning.
WARNING! Hopper Fire Risk!
For trouble free use of your pellet appliance you must per-
form cleaning as called for in these instructions. Not doing
so will result in:
Figure 17.2
• Poor operating performance
• Smoke spillage into the home
• Overheating of components
3. Assemble the crevice tool from the micro cleaning kit
to attach to a Shop Vac. Figure 17.3.
Not properly cleaning your appliance on a regular basis will
void your warranty.
Tools Needed: A Shop Vac and generic micro cleaning
kit; flat head and Phillips screwdriver; 11/32 Nut-driver or
wrench.
Figure 17.3
4.
Use the crevice tool to finish cleaning the heat exchanger
fins. It is critical that the 2 exhaust exits at the back of the
firebox floor (left and right) be thoroughly cleaned. Figure
17.4. There are several ways this can done.
a. Use the crevice tool.
b. Attach a hose 1/2 inch (12.7mm) in diameter and
approximately 2 feet (607mm) in length to your vacuum
hose.
c. Use a bottle brush and push the ash down to the
bottom. Remove the combustion (exhaust) blower
and then vacuum out the ash. Figures 18.1 and 18.2
on page 18.
Micro Cleaning Kit*
Example
* Can be purchased at your local hardware store.
Shop Vac* Example
1. It is necessary to remove the baffle to gain access to the
heat exchanger. Follow instructions for baffle removal
on page 50.
2. Vacuum the ash from the heat exchanger with an
upholstery brush to remove the majority of the ash. Be
sure to vacuum the back of the baffle also. Inspect the
drop tube and remove any residue build-up in the drop
tube. Figure 17.1.
2 exhaust exits (left and right side) must
be thoroughly cleaned. Each exit is
approximately 4 inches wide, 1 inch
across and 3 inches deep.
Figure 17.1 - Example of a dirty heat exchanger
Figure 17.4
Page 17
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
5. Cleaning Firepot with Firepot Clean-Out Tool
Cleaning Heat Exchanger, Drop Tube & Exhaust (Cont’d)
•
Frequency:
Softwood Pellets: Weekly or every 5 bags
Hardwood Pellets: Weekly or every 3 bags
Alternate Fuel: Daily or every 1 bag
By: Homeowner
5. The combustion blower must be removed to clean
the exhaust path. Follow the instructions on page 49
however you do not need to disconnect the wires.
•
a Vacuum out the exhaust area. Figure 18.2. You
may need to replace the gasket at this time also.
See Parts List for part number.
a. Be sure the wall control screen says OFF, the appliance
is allowed to cool and the power switch is in the OFF
position.
b. Use a brush to clean out the exhaust transition
path.
b. It may be necessary to use your firepot clean-out tool
to chip away material that has built up on the sides of
the firepot and to push out any clinkers.
• Larger clinkers may have to be removed from the
top of the firepot.
•
Corn clinkers can be especially difficult to break up.
• If the clinker adheres to the sides of the firepot, you
will need to manually clean the firepot.
c. After power is restored, the auto-clean system will
recycle and then clean itself.
d. The firepot floor plate must be fully closed when
finished.
Figure 18.1
Vacuum out the exhaust area.
Clinker
Figure 18.3 - Large Clinker
6. Ash Removal from Firebox
•
Frequency: Weekly or more frequently depending on
ash build-up
By: Homeowner
Figure 18.2
•
Be sure the wall control screen says OFF, the appliance
is allowed to cool and power switch is in the OFF
position.
There must not be any hot ashes in the firebox during
cleaning.
Frequent cleaning of the ash in the firebox with a vacuum
cleaner will help slow down the build-up of ash in the
exhaust blower and vent system.
Page 18
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
7. Cleaning the Hopper
11. Cleaning Convection Blower - Do Not Use
Lubrication
•
Frequency: Monthly or after burning 1 ton of fuel
(aprx. 50 bags) or when changing fuel types
By: Homeowner
•
•
Frequency: Yearly or as needed
By: Homeowner
•
a. Be sure the wall control screen says OFF, the appliance
is allowed to cool andthe power switch is in the OFF
position.
a. Be sure the wall control screen says OFF, the appliance
is allowed to cool and the power switch is in the OFF
position.
b. Use a soft brush and vacuum to clean the
propellers.
b. After burning approximately 1 ton of fuel you will need to
clean the hopper to prevent sawdust and/or fines build-
up.
12. Preparing Firebox for Non-Burn Season
b. A combination of sawdust/fines and pellets on the auger
reduces the amount of fuel supply to the firepot.
•
•
Frequency: Yearly
By: Homeowner
c. This can result in nuisance shut downs and mis-starts.
a. Be sure the wall control screen says OFF, the appli-
ance is allowed to cool andthe power switch is in the
OFF position.
• Empty the hopper of any remaining pellets.
• Vacuum the hopper and feed tube.
b. Remove all ash from the firebox and vacuum thor-
oughly.
8. Cleaning the Glass
•
Frequency: When clear view of firepot becomes
obscure
By: Homeowner
c. Paint all exposed steel, including cast-iron.
•
Use the Touch-Up paint supplied with the appliance;
or,
•
a. Be sure the wall control screen says OFF, the
appliance is allowed to cool and the power switch is
in the OFF position.
•
•
Purchase paint from your local dealer
Must use a high-temperature paint made specifi-
cially for heating appliances
b. Clean glass with a non-abrasive commercially
available cleaner. Wipe down with dry towel.
d. Cleaning the flue at the end of the burn season will
prevent corrosives to build-up and damage the flue.
Caution! Handle glass assembly with care. Glass is
breakable.
e. Outside temperatures should have no affect on the
performance of the appliance under freezing condi-
tions.
•
•
•
Avoid striking, scratching or slamming glass
Avoid abrasive cleaners
Do not clean glass while it is hot
13. Soot and Fly Ash: Formation & Need for Removal
in Exhaust Venting System.
•
Frequency: Prior to each burn season and after pro-
longed shut down.
9. Door Latch Inspection
•
By: Qualified Service Technician/Homeowner
•
•
Frequency: Prior to heating season
By: Homeowner
The products of combustion will contain small particles
of flyash. The flyash will collect in the exhaust venting
system and restrict the flow of the flue gases. Incom-
plete combustion, such as occurs during startup, shut-
down, or incorrect operation of the room heater will lead
to some soot formation which will collect in the exhaust
venting system. The exhaust venting system should be
inspected at least once every year to determine if clean-
ing is necessary.
The door latch is non-adjustable but the gasketing between
the glass and firebox should be inspected periodically to
make sure there is a good seal.
If the gasket is frayed or damaged, replace with a new
one.
10. Cleaning Exhaust Blower - Do Not Use
Lubrication
•
•
Frequency: Yearly or as needed
By: Homeowner
The venting system may need to be cleaned at least
once a year or more often depending upon the quality
of your fuel or if there is a lot of horizontal pipe sections.
Ash will build up more quickly in the horizontal sections.
a. Be sure the wall control screen says OFF, the
appliance is allowed to cool and the power switch is
in the OFF position.
b. Use a soft brush and vacuum to clean the
propellers.
Page 19
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
14. Chimney Inspection and Cleaning..
Cover area around opening to prevent staining of rugs,
furniture, etc… Work the brush up and down sev-
eral times until the chimney is clean. Use a powerful
flashlight to look into the chimney to be sure you have
cleaned it completely. Follow clean-up directions below.
•
Frequency: Prior to each burn season and after pro-
longed shut down.
By: Qualified Service Technician/Homeowner
•
In order to properly clean your chimney you will need
the following items. Make sure you have a Correctly
sized chimney brush, chimney brush rods or rope and
pull rings (depending on method used), fireplace cover
(for use with an ash vacuum or to contain dust), protec-
tive covering for furniture and rugs, tape, metal bucket,
small shovel and broom, vacuum cleaner, and a power-
ful flashlight.
For All Methods: Sweep or vacuum up all residues
prior to using stove or fireplace. Be especially careful
to check the debris behind the damper and smoke shelf
area, in elbows or “T” connections. Special hand held
chimney cleaning brushes are available to reach hard-
to-clean areas. Clean a wire bristle chimney brush after
use and coat with a rust preservative. During the burn-
ing season we highly recommend the use of Anti-Creo-
Soot or another creosote remover product to reduce the
build-up of creosote deposits.
There are four common methods used to control the
brush for effective cleaning.
1. Flexible Rod Method, Top Down (Preferred
Method): Seal off fireplace or stove opening to prevent
soot from entering the home. For fireplaces a Fireplace
Cover is a great way to seal off the opening and allow
a vacuum cleaner to attach to keep the dust out of your
home. Attach the brush securely to the flexible rod and
lower into the top of the chimney, add more rods as nec-
essary to reach the flue bottom. Work the brush up and
down several times until the chimney is clean. Use a
powerful flashlight to look into the chimney to be sure
you have cleaned it completely.
2. Flexible Rod Method, Bottom-up: Insert brush and
rod up through the fireplace damper or chimney clean-
out door. Add more rods as necessary to reach the top
of the chimney. This method is often messy since seal-
ing the opening cannot be done during cleaning. Cover
area around opening to prevent staining rugs, furniture,
etc. Use a powerful flashlight to look into the chimney to
be sure you have cleaned it completely. Work the brush
up and down several times until the chimney is clean.
3. Line and Weight Method: Seal off fireplace or
stove opening to prevent soot from entering the home.
Securely attach a compact 20-pound (minimum) weight
to one end of the brush with one accessory pull ring and
attach a rope that is more than long enough to reach
the bottom of the flue, to the other brush end. Lower the
brush into the chimney and up again until the chimney is
clean. Use a powerful flashlight to look into the chimney
to be sure you have cleaned it completely.
4. Dual Line Method: This method requires two
people, one on the roof and one below at the clean-out
or fireplace opening. Attach one rope to each end of the
brush. Drop one rope down the chimney to the person
below. Cleaning is done by alternately pulling the ropes
to vigorously move the brush up and down in the flue.
This method is often messy since sealing off the open-
ing cannot be done during cleaning.
Page 20
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Troubleshooting for Homeowner
4
A. Frequently Asked Questions
ISSUES
SOLUTIONS
1. Noise is caused by metal expanding and contracting as it heats
up and cools down, similar to the sound produced by a furnace or
heating duct. This noise does not affect the operation or longevity
of your appliance.
1. Metallic noise
2. This is normal. Clean the glass.
2. Ash buildup on glass
3. Glass has turned dirty
3. Excessive build up of ash. The lower burn settings will produce
more ash, the higher burn settings produce less. The more it burns
on low the more frequent cleaning of the glass is required.
4. The flame height adjustment needs to be reduced or the firepot
needs cleaning. Heat exchanger & combustion blower needs
cleaning.
4. Fire has tall flames with black tails and is lazy
5. Either the firepot is dirty or there is too much fuel at start-up and not
enough air.
5. Excessive smokey start-up
6. Large flame at start-up
7. Mechanical Noise
6. This is normal. Flame will settle down once the fire is established.
Some smoke is normal.
7. The floor of the firepot in the auto-clean system may make some
noise as it scrapes the ash into the ash pan.
NOTICE: Odors and vapors are released during initial operation due to the curing of high tem-
perature paint. Open windows for air circulation. Odors may be irritating to sensitive individuals.
Page 21
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
B. Wall Control Error Codes
Error Message
Possible Cause
Corrective Action
Overheat sensor (snap disc) has tripped
Turn power off to appliance and manually reset snap
disc then turn back on. If that doesn’t work, call your
dealer.
SNAP DISC TRIPPED
Convection blower may need cleaning
Auger jammed, feed motor bad
Clean convection blower if needed.
Use clean-out tool to clear jam.
AUGER JAMMED
Empty hopper and look for foreign objects and
remove
Turn the power switch OFF and then back ON to
clear error code
Out of fuel or fuel has clumped together to form Break up pellets that have clumped together
MISSED IGNITION
a dam in hopper
Refill hopper if fuel level is low
Out of fuel
Refill hopper
MIN FIREPOT TEMP
Add handful of pellets to firepot
Wrong fuel table setting
Confirm setting matches burning fuel
Adjust flame height
MAX DROP TUBE TEMP
CHECK ASHPAN
Flame height set too high
Components may need cleaning
Clean the firebox, heat exhanger, convection blower,
firepot and ash pan. If problem persists, call your
dealer.
Auto-clean jammed
Turn the power switch OFF and then back ON to
clear error code.
If ash pan is empty, check for a jam. Use the clean-
out tool and firmly push in the firepot floor holes and
flex spring and push toward home (closed position)
to release jam. If problem persists, call your dealer.
Static discharge or nearby lightening or Electric Wait 25 seconds and press any key. If the screen
SCREEN GOES BLANK
Fast Transients at the input mains
Power switch in OFF position
Hopper lid not closed all the way.
does not come back on, call your dealer.
Turned to ON position.
Close the lid. If that didn’t work the switch is out,
call your dealer.
Firebox door is not latched properly
Check the latch, if OK the door switch may be out,
call your dealer.
Fireplace may not be rolled in completely
If fireplace is completely rolled in, interlock switch
may be out, call your dealer.
Slide Rail bolts may not be installed
Out of fuel
Install bolts
Check fuel level, if OK the switch may be out, call
your dealer.
Page 22
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Installer’s Guide
Getting Started
5
tion is to vent above roof line when possible. This mini-
mizes the affects of wind loading.
A
.
Design, Installation & Location Considerations
1. Appliance Location
Since pellet exhaust can contain ash, soot or sparks, you
must consider the location of:
NOTICE: Contact local building or fire officials about
restrictions and installation inspection requirements in your
area.
• Windows
• Air Intakes
• Air Conditioner
• Overhang, soffits, porch roofs, adjacent walls
• Landscaping, vegetation
• Horizontal or vertical vent termination
•
Installation MUST comply with local, regional, state and
national codes and regulations.
•
Consult insurance carrier, local building inspector, fire
officials or authorities having jurisdiction over restrictions,
installation inspection and permits.
2. Floor Support
It is a good idea to plan your installation on paper, using
exact measurements for clearances and floor protection,
before actually beginning the installation. Location of the
appliance and chimney will affect performance.
The supporting floor under the appliance must be able to
handle the weight of the fireplace, fuel load and the weight
of the chimney.
Ensure that your floor will suport these weights prior to in-
stallation. Add sufficient additional support to meet this
weight requirment prior to installation. The weight of the
fireplace is 450 lbs and with a full hopper of fuel weighing
120 lbs, the total for the fireplace and fuel is 570 lbs.
Consideration must be given to:
• Safety, convenience, traffic flow
• Placement of the chimney and chimney connector and
to minimize the use of chimney offsets.
WARNING! Risk of Fire Damaged parts could impair safe
operation. Do NOT install damaged, incomplete or substitute
components.
• Place the appliance where there will be a clear passage
for a Listed chimney through the ceiling and roof (verti-
cal) or through exterior wall (horizontal).
• Installing the required outside air kit will affect the loca-
tion of the vent termination.
CAUTION! If burning shelled field corn, you must use ap-
proved venting specifically designed for corn to prevent
corrosion or degradation. Follow the instructions from the
venting manufacturer.
When locating vent and venting termination, the ideal loca-
Recommended Location:
• Above peak
• Inside heated space
Recommended Location:
• Above peak
Marginal Location:
Wind loading possible
•
Marginal Location:
• Below peak
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Recommended:
• Insulated exterior chase
in cooler climates
Windward
Leeward
Multi-level Roofs
Recommended:
Outside Air Intake
on windward side
NOT recommended:
Outside Air Intake
on leeward side
Figure 22.1
Page 23
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
E. Checklist to Help Determine Location
B. Thermostat Wall Control Location
The thermostat wall control’s location will have some affect
on the appliance’s operation.
Description
Vent termination location - vertical or horizontal
Venting clearances
• Maximum wire length from appliance is 100 feet (30.48m)
continuous unspliced wire. Recommended 20 gauge wire,
solid copper .
Outside air location (3 options)
Electrical connection
• When located close to the appliance, it may require a
slightly higher temperature setting to keep the rest of the
house comfortable.
Location of thermostat wall control
Clearance to combustibles
• When located in an adjacent room or on a different floor
level, you will notice higher temperatures near the appli-
ance.
Mantel projection fuel loading clearances
Sidewalls, surrounds and trim clearances
Hearth extension floor protection
CAUTION! The wall control is an integral part of the appli-
ance. No other wall control or thermostat can be substi-
tuted.
Height for loading fuel into hopper if installed on a
raised platform
Allow enough clearance to open front when
installing finishing material that protrodues
beyond the mounting frame.
C. Tools And Supplies Needed
Thickness of finishing material
Service space clearances
Tools and building supplies normally required for instal-
lation.
Reciprocating Saw
Hammer
Phillips Screwdriver
Tape Measure
Plumb Line
Wire Nuts
7/16 inch Socket Wrench
Framing Square
Electric Drill & Bits
Self-Tapping Screws
Outside Air Required
Class L or PL Pellet Vent
WARNING
DO NOT INSTALL IN SLEEPING ROOM
Level
Framing Material
Hi-temp Caulking Material
Gloves
May also need:
Vent Support Straps
Safety Glasses
D. Inspect Appliance and Components
WARNING! Risk of Fire! Damaged parts could impair safe
operation. Do NOT install damaged, incomplete or substitute
components.
•
Open the appliance and remove all the parts and articles
packed inside the Component Pack. Inspect all the parts
and glass for shipping damage.
•
•
•
Report to your dealer any parts damaged in shipment.
All labels have been removed from the glass door.
Plated surfaces have been wiped clean with a soft cloth,
if applicable.
•
Read all the instructions before starting the installation.
Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
•
Follow pipe manufacturer instructions for installation
and air clearance requirments.
Page 24
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
G. Items to Verify During Test Burn
F. Recommended Sequence of Installation
• Check for leaks in the exhaust venting system. Do you
see any smoke?
NOTICE:
• Read and understand Sections 6 through 10 for detailed
Remember on a first burn odors and vapors
are released due to the curing of the high tem-
perature paint. The focus is on the venting
system.
information before installing the fireplace.
• Follow all clearances as specified.
• The choice of finishing material and decorative front
must be determined before installation can begin as it
will determine the placement of the fireplace.
• Check overall operation, are there any error codes on
the Wall Control?
• Outside air is required on all installations and the Outside
Air Kit must be ordered separately.
• Confirm that outside air is hooked up and properly sealed.
Is there cold air infiltration?
Recommended Sequence
WARNING
1. Identify the exhaust vent and outside air locations
and install necessary venting components including
wall thimble, fire stop or roof flashing for a verti-
cal termination. NOTE: Outside Air Kit must be
ordered separately.
Crush Hazard!
To avoid tipping over, this
appliance must be securely
fastened to the floor.
2. Complete the framing.
3. Install the electrical junction box near the electrical
opening on the left side of the appliance. Maximum
distance of 9 inches (229mm) from appliance.
4. Identify the location of the wall control and run the
wire (25 ft [7.62 meters] in length) to the left side of
the appliance.
•
•
•
The fireplace must be secured in place as outlined in
Section 6 and 7.
When servicing the fireplace, the fireplace slides
foward on the rail system.
5. Prepare the fireplace for the exhaust vent adapter.
Install adapter, seal with high temp silicone and
screws and install all cover plates.
Tipping can occur if fireplace is not properly secured
to the floor.
6. Preset the nailing flanges depending on the thick-
ness of your finishing material.
7. Ensure that fireplace is level before securing in
place. If not level the decorative front will not swing
out properly.
8. IT IS CRUCIAL FIREPLACE IS ROBUSTLY
SECURED. Slide the fireplace into place and
secure to the floor with the securing brackets and to
the wall. See page 33 for detailed instructions.
9. Attach the exhaust and outside air venting to the
appliance.
10. Hook up power and the wall control.
11. Slide the fireplace out on the rail system to validate
that it is secure and there is no deflection in the
outer can.
12. Slide the fireplace back into the outer can. Re-attach
the bolts and brackets. Double check they are cor-
rectly positioned to ensure the exhaust gaskets are
properly sealed to prevent combustion leakage.
13. A burn test must be performed before finishing
material is installed. (See Item “G”).
14. Install the finishing material.
15. Install the decorative front.
Page 25
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Framing Dimensions & Clearances
6
A. Recommended Locations
10-1/8 in (257mm)
Top/Rear Vent & Rear
Outside Air
14-1/4 in (362mm)
Junction Box
27-1/4 in (692mm)
Outside Air, Right
& Left
43-1/2 in
(1105mm)
26-7/8 in
(682mm)
Top Vent
29-3/4 in
(756mm)
61-1/2 in
(1563mm)
27-1/2 in
(699mm)
30 in (762mm)
Recommended for
Service Space
30 in (762mm)
Recommended for
Service Space
61-1/2 in
(1563mm)
27-1/2 in
(699mm)
See Section 8 for outside air
locations.
87 in
(2210mm)
Outside Air Kit is REQUIRED for
all installations.
30 in (762mm)
Recommended for
Service Space
48 in
(1219mm)
30 in (762mm)
Recommended for
Service Space
30 in (762mm)
Recommended for
Service Space
27-1/2 in
(699mm)
27-1/2 in
(699mm)
30 in (762mm)
Recommended for
Service Space
Figure 25.1
WARNING
Any hearth extension is to be installed as illus-
trated in Figure 25.2
B. Hearth Extension
•
•
If employing a hearth extension, any parts or
materials used in construction must be non-
combustible.
Location
Inches Millimeters
D
Floor protection hearth extension from
door opening
6
6
152
152
E
Floor protection to the side of door
opening
D
E
Figure 25.2
Page 26
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
NOTE
•
•
It is necessary to use sealing strips of non-combustible
materials between the fireplace hearth and factory-built
hearth extension.
The use of a sand-cement grout between the hearth
and an on-site constructed hearth extension is also
necessary.
C. Sealing at the Penetration of Building
Envelope
The first step for successfully creating an air barrier system is to seal all of the holes in the building envelope. Too
often, builders concentrate on air leakage through windows, doors, and walls, and ignore areas of much greater
importance. A key source of leakage—called a bypass—is hidden from view behind chases for flues and ductwork. It
is important to make sure these areas are sealed to prevent leakage. A common way to seal areas behind chases for
flues and ductwork is to attach and caulk a piece of plywood or foam sheathing material that covers the entire opening.
Seal penetrations. If a flue requires a noncombustible clearance, use a noncombustible metal collar, sealed in place to
span the gap.
Sealing these bypasses is critical to reducing air leakage in a home and maintaining the performance of insulation materials.
D. Frame the Fireplace
Figure 26.1 shows typical framing using combustible materials (2x4 lumber shown).
•
•
Framing across the top of fireplace must be above top standoffs.
See page 33 for detailed information regarding sub-floor material requirements.
See Section 8 for outside air locations.
Outside Air is REQUIRED for all installations.
A
B*
30
C**
38-1/4
972
D
7
inches
mm
27-1/2
699
762
178
*
If interior of chase will be drywalled, add the thick-
ness to this measurement.
** Adjust header height for a raised platform under
fireplace, Taking into consideration the maximum
height allowed for loading fuel into the hopper.
Header MUST NOT
be notched!
D = extra space needed
C
for securing fireplace to the floor
and for outside air connection if
it is installed on side of fireplace
D
A
B
Figure 26.1 - Framing the Fireplace
Page 27
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
E. Construct the Chase
You may enclose the vent system in a chase. See Figures
27.1 & 27.2.
Termination Cap
Metal Chase Top
1. Appliance and chimney enclosed in an exterior chase.
2. Chimney offset through exterior wall and enclosed in chase.
3. Chase constructed on roof on non-combustible material.
Ceiling
Firestop
Note: In cooler climates, all chase walls should be insulated.
False Ceiling
Attic
Insulation
Shield
Tabs
Insulation in the
outside walls
of the chase
Ceiling
Firestop
2
1
3
Insulation
Insulation
False Ceiling
Chimney
Figure 27.1- Chase Constructions
False Ceiling
•
•
Check local/regional building codes for compliance.
Construct ouside wall of chase as you would the outside
walls of the building to prevent cold air drafting problems.
The chase should not break the outside building envelope
in any manner. All outer walls need to be insulated.
Figure 27.2 - Chase Assembly
WARNING! You must install false ceilings and ceiling
firestops at each floor of the chase or every 10 ft (3.05 m)
to control spread of fire.
•
•
Install vapor and air infiltration barriers per local/regional
building codes.
Holes and other openings should be caulked with high
temperature caulk or filled with unfaced fiber glass
insulation.
•
Hearth & Home Technologies Inc. suggests you sheetrock
and tape (or use an equivalent method) all inside surfaces
of first level for maximum air tightness.
COOLER CLIMATES
•
•
•
In cooler climates, Hearth & Home Technologies Inc.
recommends you insulate walls, ceiling, base plate,
cantilever floor. Use batt type insulation between the
joists.
WARNING! Risk of Fire! You must maintain the pellet pipe
manufacturer’s minimum air space clearance to insulation
and other materials surrounding the chimney system.
Place a sheet of plywood or a raised platform on
cement slab under appliance only. You need to secure
the appliance to the cement slab so do not extend the
plywood so as to interfer with the attachment.
• Insulation and other materials must be firmly secured
to prevent accidental contact with chimney system.
• Failure to prevent contact between insulation or other
materials and chimney system may cause overheat-
ing and fire.
A firestop spacer should be installed in an insulated
false ceiling at the 8 ft. (2.4m) level above the fireplace
assembly. This reduces heat loss through the chase. It is
required that firestops be installed every 10 ft (3.05m) to
control spread of fire, but 8 ft is recommended to prevent
heat loss.
Page 28
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
F. Finishing Material
2. Flush with the Mounting Frame
NOTICE: Non-combustible material is not needed to finish
The finish material can not be thicker than 1-1/2 inches
this appliance.
(38mm) to use this method. Figure 28.3.
• Set the nailing flanges for sheet rock thickness and
install the appliance.
It is important that the finishing material is determined before
the appliance is secured to the floor. Depending on the fin-
ishing material and installation method, the appliance may
need to be positioned further in or out of the wall.
• Install the mounting frame.
• Install the finishing material to edge of the mounting
frame.
There are three ways finishing material can be applied:.
1. Behind the mounting frame
2. Flush with the mounting frame
3. Protrudes beyond the mounting frame
Finishing Material Flush
with Mounting Frame
1. Behind the Mounting Frame
The mounting frame is designed to have a 1/2 inch (13mm)
overlap on the sides and the top of the framing opening.
Figure 28.1.
Mounting Frame
Finishing Material Behind
the Mounting Frame
Figure 28.3.
3. Protrudes Beyond the Mounting Frame
Mounting Frame
This method is mainly used for a brick or stone installa-
tion. When finishing material is protrudes of the mounting
frame and front, there must be a 1-1/4 inch (32mm) airflow
clearance in front of the mounting frame. Figure 28.4.
Figure 28.1.
Finishing Material Beyond Door Frame
Masonry Spacer
Positioning the nailing flanges:
• Slide the nailing flanges all the way to the front and this
will set the appliance for 1/2 inch (13mm) sheet rock.
Door Frame
Maintain 1-1/4 inch (32mm) air
clearance in front of door frame
• If tile, marble or other flat surface finish material is desi-
ered and you want the mounting frame to cover the cut
edge, set the nailing flanges at a dimension of the sheet
rock thickness plus the finishing material thickness.
Figure 28.2.
Example: Sheetrock = 1/2 inch (13mm)
Finish Material = 3/8 inch (9.5mm)
Figure 28.4.
Move flange: 7/8 inch (22.5mm)
Use the masonry spacer supplied with the Front to position
the finishing material at the proper dimension. Remember
to keep the Front opening clearances in mind when finishing
material is protrudes of the Front. (See pages 29-30) .
Front of Fireplace
Adjustment Screw
7/8 in
• Set the nailing flanges for sheet rock thickness and
install the appliance.
(22.5mm)
• Install the mounting frame.
Adjustable Nailing Flange
• Install the finishing material to edge of the mounting
frame.
• Complete the installation following all specified clear-
ances to combustibles.
Figure 28.2
December 6, 2011
Page 29
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
G. Front Opening Clearance
Curved Front
Natural Front
Tuscan Front
TOP VIEW
Appliance
Nailing Flange
Drywall
Finishing Material
Masonry Spacer
*
3 in
(76mm)
1-1/4 in
(32mm)
1/2 in
(13mm)
Mounting
Frame
3-1/2 in
(89mm)
Opening Clearances for the Curved,
Tuscan and Natural Fronts
5-1/2 in
(140mm)
6-1/2 in
(165mm)
3-1/2 in (89mm)
4 in (102mm)
8 in
(203mm)
*Note: The Masonry Spacer is used
when the finishing material is brick or
stone or any material that is proud to
the mouting frame. See page 28 for
details.
9 in
(229mm)
Edge of
appliance
outer skin
4-1/2 in (1
14mm)
5 in (127mm)
5-1/2 in (140mm)
6 in (152mm)
Mantel Leg
Figure 29.1
Page 30
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
G. Front Opening Clearance (Cont’d)
Studio Front
TOP VIEW
Appliance
Nailing Flange
Drywall
Finishing Material
Masonry Spacer*
1/2 in
(13mm)
Mounting Frame
5-1/4 In (133mm)
7-1/2 In (190mm)
Opening Clearances
for the Studio Front
Edge of appliance
outer skin
9 in (229mm)
*Note: The Masonry Spacer is used
when the finishing material is brick or
stone or any material that is proud to the
mounting frame. See page 28 for
details.
Mantel Leg
Figure 30.1
Page 31
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
H. Mantel Fuel Loading Clearances
NOTE: Be sure to consider the process of loading fuel when choosing and locating a mantel.
Mantel
Finishing Material
24 in (610mm)
Drywall
9 in (229mm)
8 in (203mm)
7 in (178mm)
6 in 152mm)
5 in (127mm)
(1:1 rise to run ratio)
4 in (102mm)
3 in (76mm)
2 in (51mm)
1 in (25mm)
1/2 in (13mm)
Masonry Spacer
10-1/2 in
(267mm)
74 in
(1880mm)
to Floor
4-1/2 in
(114mm)
2-1/2 in
(64mm)
8-1/2 in
(216mm)
6-1/2 in
(165mm)
9-1/2 in
(241mm)
1-1/4 in
(32mm)
5-1/2 in
(140mm)
3-1/2 in
(89mm)
7-1/2 in
(191mm)
Appliance
Side View
Floor Line
Figure 31.1
Page 32
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
I. Non-Combustible Materials
•
Materials which will not ignite and burn, composed of any
combination of the following:
-
-
-
-
Steel
Brick
Concrete
Glass
- Iron
- Tile
- Slate
- Plasters
•
•
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C.
Non-Combustible Sealant Material
-
-
-
-
-
Sealants which will not ignite and burn:
Rutland, Inc. Fireplace Mortar #63,
Rutland 76R,
Nuflex 304,
GE RTV106 or GE RTB116 (or equivalent).
J. Combustible Materials
•
Materials made of or surfaced with any of the following
materials:
-
-
-
-
Wood
Plant fibers
Plastic
Compressed paper
•
Any material that can ignite and burn; flame proofed or
not, plastered or un-plastered
WARNING! Risk of Fire! You must maintain
clearances.
•
Do NOT cover metal fireplace front with combustible
materials.
•
Install combustible materials only to specified clearances
on top front, sides and back edges.
Page 33
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Installation of Fireplace
7
be turned around so the longer flange attaches to the floor. We
recommend that the brackets are turned around for a concrete
attachment. Figure 33.1.
Caution! Risk of Cuts/Abrasions. Wear protective
gloves and safety glasses during installation. Sheet
metal edges are sharp.
There are 4 holes on each flange. Secure each flange with 2
bolts. Choose the holes that best secures the fireplace to the floor.
Please note that you always want to include the washer on the
bolts that attach to the floor.
A. Position the Fireplace
•
Place the fireplace on a continuous flat surface or install on a
raised platform.
You can re-use the same bolts and washers that attach the fire-
place to the pallet. However, there is also a full set of bolts and
washers included in the component pack.
•
Follow framing instructions in Section 6.
WARNING! Risk of Fire! Prevent contact with sagging, loose
insulation.
After properly securing the fireplace to the floor, the 2 slide rail “L”
brackets that hold the rails in place for shipping may be removed
and discarded. Figure 33.2.
• DO NOT install against vapor barriers or exposed insula-
tion.
• Secure insulation and vapor barriers.
• Provide minimum air space clearances at the sides, top
Front & rear bracket on each side
securing fireplace to pallet
and back of the fireplace assembly as outlined in Section 6
.
B. Sub-Floor Material & Securing Fireplace
NOTE: Finish material and installation method must be selected
before securing the fireplace to the floor.
WARNING
Crush Hazard!
Figure 33.1
To avoid tipping over, this
appliance must be securely
fastened to the floor.
Flooring Material Under Appliance:
“L” Shipping Bracket Holding
Rails in Place. One on each
side.
Concrete subflooring is the most secure method. Follow the manu-
facturing instructions that come with the concrete anchor bolts for
properly securing fireplace to the concrete. In cooler climates place
a sheet of plywood or a raised platform on cement slab under appli-
ance only. You need to secure the appliance to the cement slab so
do not extend the plywood so as to interfer with the attachment.
Figure 33.2
Wood Flooring
Testing for Deflection & Removing Handles
Non-Raised Hearth
•
Minimum 19mm thickness plywood of C-C plugged grade
or better exterior glue plywood.
Remove the 2 bolts from each lower side of the fireplace and slow-
ly roll out the fireplace on the rail system.
Raised Hearth
Inspect attachment of brackets to the floor and fireplace to ensure
there is zero deflection in the outer can when it is rolled out on the
rails.
• Minimum of 2 layers of 19mm thickness plywood of C-C
plugged grade or better exterior glue plywood.
• The raised base must be firmly secured to the house
framing members.
CAUTION!
• If there is any deflection, this could cause damage to the finish-
ing material such as tile, mortar, etc.
CDX or OSB plywood or particle board are not acceptable in
either installation.
• If fireplace is not properly secured, finishing materials will not be
covered under warranty.
Securing Fireplace
Remove the lift handles as they could rattle if left in place. Re-
install the bolts in the firebox sides to prevent leaks after removing
the handles.
NOTE: Fireplace MUST be level before securing in place.
The fireplace is secured to the pallet with 4 brackets, 2 on each
side. Re-use these same brackets to secure the fireplace to the
floor.
Slide the fireplace back into the outer can. Re-attach the bolts and
brackets. Double check they are correctly positioned to ensure
the exhaust gaskets are properly sealed to prevent combus-
tion leakage.
The brackets are attached with the short flange attached to the
pallet and the long flange attached to the fireplace. These may
Figure 34.1
Page 34
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
D. Connecting Wall Control To Fireplace
C. Junction Box & Wiring Diagram
Caution! The fireplace should be securely attached to the
floor prior to making final electrical connections.
1. There is a 5 screw terminal connection bar that is located
in the lower left side of the fireplace above the slide rails.
Figure 34.3.
2. Route the 25 foot (7.62m) long white wall control wire that
is supplied in the component pack through the rubber
grommet in the left side of the fireplace outer can. Figure
34.1
WARNING
Shock Hazard
•
•
•
A grounded metal outlet power supply box is
required for all installations.
3. The center 3 screws are for the thermostat wall control
wires and the 2 outer screws are mounting screws and
should not have wires attached to them.
Provides a positive ground path to earth for
outer can of the fireplace.
The thermostat wires are color coded. The green wire
is on the top, the white in the middle and the red on the
bottom.
Protects against possible electrical shock.
5. Attach the wall control wire to the thermostat wall control
Follow the directions on page 35. Do not pinch the con-
trol wires with any staples between the fireplace and wall
control. Figure 35.1 on page 35.
1. Disconnect power supply providing power to the outlet
box you intend to use.
2. The power supply cord is inside a 7-1/2 foot (2.29m)
long 3/8 inch (9.5mm) flexible conduit cable located and
attached to the left side of the outer can. Figure 34.1.
The cable comes with an insulated snap-in connection.
6. Bend back the 3 red spade connectors towards inside of
outer can and away from the fireplace. Wires should not
be in the way when the fireplace is rolled out on the rail
system.
3. Locate the metal outlet box within 7-1/2 feet (2.29m) of
the fireplace. (Note: Metal outlet box not supplied).
4. Feed the power cord into the 1/2 inch (12.7mm) standard
knockout of the outlet box and then press the connection
into the metal outlet box.
5. The power supply cord has black, white and green wires
to connect to the outlet box.
Black wire: Connects to 120V AC 15-20 amp circuit
White wire: Connects to neutral wire
Green wire: Connects to ground wire and outlet box
6. Ensure the 2 green grounding wires are securely attached
to the grounding screw. Figure 34.2.
Power Supply Cord inside 7.5 ft
(2.29m) Flexible Cable
White
Wires
Black
Wires
Matching
Color Dots
Green
White
Red
Grounding
Screw
Fireplace Left Lower Front
Thermostat Wall Control Wire
Both Green Grounding Wires
Attach to Grounding Screw
Figure 34.1 - Power Supply Cord
and Wall Control Wire
Figure 34.3 - Terminal Connec-
tion Bar
Figure 34.2 - Metal Outlet Box
Page 35
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
F. Installing Flue Collar, Vertical or Horizontal
E. Thermostat Wall Control Installation
The fireplace ships from the factory without the flue collar
and gasket attached. They are located in the component
pack inside the firebox. Follow the steps below for a vertical
or horizontal installation.
NOTICE: The thermostat wall control should be mounted
on an inside wall and not in direct line with the appliance
convection air.
NOTICE: If the thermostat wall control is located too close
to the appliance, you may need to set the temperature setting
slightly higher to maintain the desired temperature in your
home.
Vertical Installation
1. Remove the flue collar and gasket from the component
pack. Push out the 6 slugs in the gasket.
Consideration should be given to the mounting material
when installing the wall control.
2. Remove both the top and rear cover plates. Save screws
and plates for later re-attachment.
If mounting the wall control to a sheet rock surface you
should use the provided anchors for mounting.
3. Place the orange flue gasket over the locating pins on
the exhaust flue transition on the back of the fireplace.
Figure 35.2.
If mounting the wall control to a wood surface or an electri-
cal outlet box then the fasteners provided will suffice and
the anchors need not be used.
4. Insert the flue pipe through the top cover plate.
5. Before inserting the flue collar into the pipe, liberally
silicone the end of the flue collar with Hi-Temp silicone
about 1-1/2 inches (38mm) wide. Figure 36.1 on page
36.
1. Remove the front cover of the wall control by prying the
cover off with a small screwdriver or your fingernail. Place
the front side to the packaging to protect it from damage
while installing the sub base.
NOTE: You will need to install one section of 3 inch (76mm)
diameter vent pipe to clear the outer can cover plate before
installing a 3 to 4 inch (76-102mm) pellet pipe adapter for
the balance of the venting.
2. Route the wires into the wall control leaving only the
amount necessary to make the connection to the terminal
block in the upper left hand corner remaining. The wires are
routed to the terminal block according to the letters printed
in the thermostat sub base.
6. Lay the first section of pipe on its side for screw attach-
ment. The 2 screws need to be directly above the locat-
ing pins, 180 degrees apart. Figure 36.2 on page 36.
Red at the top
Green in the middle
White at the bottom
7. Drill holes through the pipe walls directly into the flue
collar. Attach screws through pipe into flue collar.
3. Push as much extra wire as possible back into the wall
and seal the hole in the wall with putty or insulation.
8. Carefully feed the flue collar and pipe through the outer
can top flue opening and guide the flue collar base plate
over the 2 locating pins. Secure with 4 screws provided
in component pack.
4. When re-installing the cover make sure that the wire
routing does not interfere with any of the components.
Make adjustments as needed and snap cover back into
place making sure that all locking tabs snap into place.
9. Re-attach the top cover plate to the top of the fireplace
and the rear cover to the back of the outer can. Figure
36.4 on page 36.
Top
4 screws in outer corner holes
Red Wire
Green Wire
White Wire
Locating Pins
Bottom
Figure 35.1- Back Side of Wall Control with
Cover Off
Figure 35.2- Install Orange Flue Gasket
Page 36
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Vertical Installation (Cont’d)
Horizontal Installation
Pipe
1. Remove the flue collar and orange gasket from the component
pack. Push out the 6 slugs in the gasket.
2. Remove the rear cover plate. Save screws and plate for later
re-attachment.
Flue Collar
Liberally silicone
all around flue
collar before
3. Place the orange flue gasket over the locating pins on the
exhaust flue transition on the back of the fireplace. Figure
35.2 on page 35.
inserting into pipe
4. Position the flue collar over the gasket and secure in place.
Top Cover Plate
Figure 36.5.
5. Position the rear cover plate,secure in place. Figure 36.6.
Figure 36.1
6. Before placing the pipe over the flue collar, liberally silicone
the end of the flue collar with Hi-Temp silicone about 1-1/2
inches (38mm) wide.
Drill Holes for Screws
above Locating Pins
7. Drill holes through the pipe walls directly into the flue collar
one on each side, 180 degrees apart. Screw the pipe to the
flue collar with 2 screws. Figure 36.7.
X
Locating Pins each Side
Locating Pin
on Each Side
Rear Cover Plate
Installed with Hole
at the Bottom
Figure 36.2
Flue Collar in Horizontal Position
Insert assemblied
pipe and flue collar
through top of outer
can and over gasket.
Figure 36.5
Figure 36.6
Secure in place
with 4 screws
Liberally silicone flue collar
before placing pipe over collar.
Figure 36.3
Secure top
cover plate in
place.
Secure pipe to flue collar with 2
screws, 180 degrees apart
Attach rear cover plate
with hole at the top and
secure in place.
Figure 36.7
Figure 36.4
December 6, 2011
Page 37
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Vent Information
8
A. Venting Termination Minimum Requirements
V
N
N
N
Electrical
Service
V
V
Inside Corner
N
V
G
V
A
H
D
P
E
O
L
C
B
FIXED
CLOSED
FIXED
CLOSED
V
OPEN
V
OPEN
B
G
F
V
M
V
I
X
V
A
B
B
J or K
Figure 37.1
V
G
Termination Cap
X
Restricted Area
Air Supply Inlet
Gas Meter
An Outside Air Kit is required on all installations. Outside Air Kit must be ordered separately.
A
12 in.
Above Finish Grade (the grade surface
must be a non-combustible material
24 in.
Above grass, top of plants, wood or any other com-
bustible
B
B
C
12 in.
12 in.
6 in.
Open door or window: below or to the side
Open door or window: above
12 in.
Clearance from any forced air intake of other appli-
ance
12 in.
15 in.
Clearance horizontally from combustible wall
Permanently closed window: above, below
or to the side
Vented directly through a wall, minimum length of
horizontal pipe
D
18 in.
Vertical clearance to a ventilated soffit
located above the terminal within a hori-
zontal distance of 2 ft from the center-line
of the terminal
12 in. horizontal Minimum horizontal or vertical terminations must
12 in. vertical
protrude from wall
NOTICE:
E
F
12 in.
12 in.
12 in.
36 in.
Clearance to unventilated soffit
Clearance to outside corner
Clearance to inside corner
Do NOT Terminate Vent:
G
H
•
In any location that will allow flue gases or soot to enter
or stain the building.
Above gas meter/regulator measured from
horizontal center-line of regulator
•
•
In any location which could create a nuisance or hazard.
I
36 in. USA
72 in. Canada
Clearance to service regulator vent outlet
In any enclosed or semi-enclosed area such as a carport,
garage, attic, crawl space, under a sun deck or porch,
narrow walkway.
J
12 in.
Clearance to non-mechanical air supply
inlet to the building or the combustion air
inlet to any other appliance
•
Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
K
L
10 ft horizontal Clearance to mechanical air supply
3 ft vertical
7 ft.
Above paved sidewalk, paved driveway
located on public property
NOTICE:
Termination must exhaust above air inlet elevation.
M
N
12 in.
Under an open veranda, porch, deck or
balcony
•
It is recommended that at least 60 inches (1.52m) of vertical
pipe be installed when appliance is vented directly through a
wall. This will create a natural draft, which will help prevent
the possibility of smoke or odor venting into the home during
a power outage.
See Note
below*
Electric service: above, below or to the
side (location must not obstruct or interfere
with access)
O
P
24 in.
12 in.
Adjacent building, fences and protruding
parts of the structure
Clearance above roof line for vertical
terminations
•
•
It will also keep exhaust from causing a nuisance or hazard
by exposing people or shrubs to high temperatures.
*NOTE: Consult local building, fire officials or authorities having
jurisdiction. Local codes or regulations may require different
clearances.
The safest and preferred venting method is to extend the
vent vertically through the roof or above the roof.
Page 38
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
B. Avoiding Smoke and Odors
Vent Configurations
To reduce probability of reverse drafting during shut-down
conditions Hearth & Home Technologies strongly recom-
mends:
Negative Pressure, Shut-Down and Electrical Power
Failure
To reduce the probability of back-drafting or burn-back in
the pellet appliance during power failure or shut down con-
ditions, it must be able to draft naturally without exhaust
blower operation.
•
Installing the pellet vent with a minimum vertical run
of 5 feet (1.52m). Preferably terminating above the
roof line.
•
Installing the outside air kit at least 4 feet (1.22m)
below the vent termination.
Negative pressure in the house will resist this natural draft
if not accounted for in the pellet appliance installation.
To prevent soot damage to exterior walls of the house and
to prevent re-entry of soot or ash into the house:
Heat rises in the house and leaks out at upper levels. This
air must be replaced with cold air from outdoors which
flows into lower levels of the house.
•
•
Maintain specified clearances to windows, doors and
air inlets, including air conditioners.
Vents and chimneys into basements and lower levels of the
house can become the conduit for air supply and reverse
under these conditions.
Vents should not be placed below ventilated soffits.
Run the vent above the roof.
•
•
Avoid venting into alcove locations.
Outside Air
Vents should not terminate under overhangs, decks
or onto covered porches.
An outside air kit is required in ALL installations. The Out-
side Air Kit must be ordered seperately.
•
Maintain minimum clearance of 12 inches (305mm)
from the vent termination to the exterior wall. If you
see deposits developing on the wall, you may need
to extend this distance to accommodate your installa-
tion conditions.
Per national building codes, consideration must be given
to combustion air supply to all combustion appliances.
Failure to supply adequate combustion air for all appli-
ance demands may lead to backdrafting of those and other
appliances.
Optional Battery Back-Up
When the appliance is roof vented (strongly recommended):
The air intake is best located on the exterior wall ori-
ented towards the prevailing wind direction during the
heating season.
Hearth & Home Technologies supplies an optional battery
back-up system that operates the fireplace during power
failure conditions to prevent smoking. In shutdown mode,
the battery back-up will not prevent smoking. See Section
2 for details.
When the appliance is side-wall vented:
The air intake is best located on the same exterior wall
as the exhaust vent outlet and located lower on the wall
than the exhaust vent outlet.
Hearth & Home Technologies assumes no responsibil-
ity for, nor does the warranty extend to, smoke damage
caused by reverse drafting of pellet appliances under shut
down or power failure conditions.
The outside air supply kit can supply most of the demands
of the pellet appliance, but consideration must be given to
the total house demand.
House demand may consume the air needed for the appli-
ance. It may be necessary to add additional ventilation to
the space in which the pellet appliance is located.
Consult with your local HVAC professional to determine the
ventilation demands for your house.
Page 39
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
C. Negative Pressure
D. Draft
WARNING! Risk of Asphyxiation! Negative pressure can
cause spillage of combustion fumes and soot.
Draft is the pressure difference needed to vent fireplaces
successfully. When a fireplace is drafting successfully, all
combustion byproducts are exiting the home through the
chimney.
Negative pressure results from the imbalance of air avail-
able for the fireplace to operate properly. It can be strongest
in lower levels of the house.
Install through the warm airspace enclosed by the building
envelope. This helps to produce more draft, especially dur-
ing lighting and die-down of the fire.
Causes include:
•
•
•
Exhaust fans (kitchen, bath, etc.)
Range hoods
Considerations for successful draft include:
•
•
Preventing negative pressure
Location of fireplace and chimney
Combustion air requirements for furnaces, water heaters
and other combustion appliances
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of the chimney
system caused by:
•
•
•
•
Clothes dryers
Location of return-air vents to furnace or air conditioning
Imbalances of the HVAC air handling system
Upper level air leaks such as:
- Recessed lighting
•
•
•
•
Inadequate draft due to environmental conditions
Downdrafts
Tight sealing construction of the structure
Mechanical exhausting devices
- Attic hatch
- Duct leaks
To minimize the effects of negative air pressure:
•
•
•
•
Install the outside air kit with the intake facing prevailing
winds during the heating season
Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the fireplace
Avoid installing the appliance near doors, walkways or
small isolated spaces
•
•
•
Recessed lighting should be a “sealed can” design
Attic hatches weather stripped or sealed
Attic mounted duct work and air handler joints and seams
taped or sealed
Page 40
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
E. Chimney and Exhaust Connection
WARNING! RISK OF FIRE!
•
•
Only LISTED venting components may be used.
NO OTHER vent components may be used.
CAUTION!
•
DO NOT CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING ANOTHER APPLIANCE.
DO NOT INSTALL A FLUE DAMPER IN THE EX-
HAUST VENTING SYSTEM OF THIS UNIT.
• Substitute or damaged vent components may impair
safe operation.
•
WARNING
Vent surfaces get HOT, can cause burns
if touched. Non-combustible shielding or
guards may be required.
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type "L" or "PL" venting system. It can be vented
vertically or horizontally.
2. Mobile Home: Approved for all Listed pellet vent. As
with all installations a Quadra-Fire Outside Air Kit must
be used with manufactured home installations.
WARNING! RISK OF INJURY OR PROPERTY
DAMAGE!
3. INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
•
•
•
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
4. Exhaust Venting System: Secure to the appliance with
at least 2 screws 180 degrees apart. Also secure all
connector pipe joints with at least 3 screws through each
joint.
Refer to the owner’s information manual provided with this
appliance.
For assistance or additional information consult a qualified
installer, service agency or your dealer.
NOTE: All pipe must be welded seam pipe whenever
possible. Seal pipe joints with high temperature silicone
(500°F [260°C] minimum rated only).
NOTE: If burning shelled field corn, you must use
approved venting specifically designed for corn. Follow
the instructions from the venting manufacturer.
F. Equivalent Feet of Pipe
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent size.
Figure 40.1.
Example of 3 Elbow-Rear Vent Termination Calculation
Pellet Venting
Component
# of
Elbows
Feet of Multiplied Equivalent
Components
Equivalent Feet
2 ft.
Pipe
By
Feet
o
90 Elbow or Tee
3
X
5
15
o
45 Elbow
X
3
3 ft.
Horizontal Pipe
Vertical Pipe
7
2
X
1
7
1
X
0.5
Total Equivalent Feet
23
2 ft.
Note: This is a generic example and is not
intended to represent any specific fuel type.
2 ft.
Figure 40.1
Page 41
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
G. Pipe Selection Chart
WARNING! RISK OF FIRE!
The chart will help you in determining proper venting size
according to the equivalent feet of pipe calculated previously
and the altitude above sea level of this installation.
Figure 41.1.
Do NOT pack insulation or other combustibles between
firestops.
•
ALWAYS maintain specified clearances around venting
and firestop systems.
a. Locate the calculated equivalent feet of pipe on the verti-
cal left side of the chart.
•
Install firestops as specified.
Failure to keep insulation or other material away from vent
pipe may cause fire.
b. Move to the right horizontally on the chart until you reach
your altitude above sea level.
WARNING
c. If you fall below the diagonal line, 3 or 4 inch (76 to
102mm) pipe may be used.
It is critical to have a working smoke detector
installed in the home of unit operation.
d. If it is anywhere above the diagonal line, a 4 inch (102mm)
diameter pipe is required.
•
Smoke alarms that are properly installed and
maintained play a vital role in reducing fire deaths and
injuries. Having a working smoke alarm reduces the
chance of fire related injuries..
NOTICE:
•
•
A90° elbow is 5 times as restrictive to the flow of exhaust
gases under positive pressure as 1 foot (305mm) of hori-
zontal pipe.
A foot of horizontal pipe is twice as restrictive as a foot of
vertical pipe.
WARNING
Products of combustion generate carbon monoxide and
different fuels generate different levels. Carbon monoxide
Only use approved fuels in this appliance.
Always keep door shut during operation. Operating this unit
with doors open can allow CO to leak into the home.
•
•
30
4 in. (102mm) Diameter Pipe Only
Example 1
CO can kill you before you are aware it is in your home. At
lower levels of exposure, CO causes mild effects that are often
mistaken for the flu. These symptoms include headaches,
dizziness, disorientation, nausea and fatigue. The effects of CO
exposure can vary greatly from person to person depending on
age, overall health and the concentration and length of exposure.
20
Equivalent Pipe
Length In Feet
Example 2
10
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
0
1
2
3
4
5
6
7
8
9
10
ALTITUDE IN THOUSANDS OF FEET
Figure 41.1
Example 1: If the equivalent length of pipe is 23 feet (7m) with altitude
of 8,000 feet (2438m) you must use 4 inch (102mm) diameter type “L”
or “PL” vent.
Example 2: If the equivalent length of pipe is 12 feet (3.7m) with altitude
of 6,000 feet (1829m) you may use 3 or 4 inch (76 to 102mm) diameter
type “L” or “PL” vent.
Page 42
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
H. Outside Air Locations & Considerations
Door
Door
Rear Vent
C
L
C
L
C
L
C
C
L
C
L
L
C
C
L
4-7/8 in.
(124mm)
L
4-7/8 in.
(125mm)
4-7/8 in.
(24mm)
9-1/4 in.
(235mm)
1-3/4 in.
(44mm)
Outside Air
1-3/4 in.
(44mm)
Outside Air
Outside Air
Rear of Fireplace
Right Rear Corner
Left Rear Corner
Figure 42.1 - Outside Air Inlet Locations
NOTE: The fireplace ships from the factory with the left and right outside
air covers installed. Once the location for the outside air inlet has been
choosen, install the outside air covers over the two unused air inlets.
NO
NO
Outlet blocked by
snow, leaves, etc.
Garage or
combustible
liquids storage
NO
Attic space
NO
Outlet placed
higher than 3 ft
below the
termination cap
YES
Clear area
outside
Fireplace
house or in
“ventilated”
crawl space
Figure 42.2 - Outside Combustion Air Placement
Page 43
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
I. Outside Air Kit Installation
Included in Kit: 2 wire ties, 1 collar assembly, 1 termina-
Outside air is required on ALL installations. The Out-
side Air Kit must be ordered seperately.
tion cap assembly, 1 trim ring, fasteners.
NOTE: 3 Inch (75mm) Aluminum Flex Pipe Not Supplied.
CAUTION! Risk of Fire or Asphyxiation! Do not draw
outside combustion air from wall, floor or ceiling cavity, or
enclosed spaces such as an attic or garage.
Tools Needed: Phillips Head screwdriver; wire cutters;
hole saw or jig saw.
• Do not place outside air inlet close to exhaust vents
or chimneys. Fumes or odors could be drawn into the
room.
1. Measure distance from floor to air vent opening in appli-
ance and mark location on wall.
Use saw to cut opening in wall.
• Locate outside air inlet to prevent blockage from
leaves, snow/ice, or other debris. Blockages could
cause combustion air starvation.
• Cut a 3-1/2 to 4 inches (89-102mm) opening on inside
wall.
* Cut a 4 to 4-1/2 inches (102-114mm) opening on out-
side of house.
Install Outside Air Kit
•
Keep duct runs short and straight to minimize restriction.
2. Use wire tie to secure flex pipe to collar assembly.
3. Slide trim ring over flex pipe and run pipe through wall.
•
The outside air kit can be installed in three different
locations - the left or right side or from the back of the
fireplace. Figure 42.1 on page 42.
4. Attach flex pipe (not supplied) to outside termination
cap with second wire tie.
•
Locate the air inlet in a clear area, preferably into prevailing
wind during the heating season. Figure 42.2 on page 42.
5. Secure termination cap to outside surface.
6. Secure trim ring to the wall.
•
•
Install as shown in Figure 43.1.
The air duct may be run vertically.
Collar
Wire Ties
3 inch Aluminum Flex
Pipe (not included)
Trim Ring
Termination Cap
Figure 43.1 - Outside Air Installation
Page 44
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
J. Vertical - Interior - Typical Installation
We recommend a minimum of 60 inches (1.52m) verti-
cal, however above the eave is preferred.
Termination
Cap
Both installations are approved for mobile home instal-
lations. Must use 3 or 4 inch (76mm to 102mm) “L”
or “PL” Listed pellet venting or Listed double wall pipe
and Quadra-Fire Outside Air Kit in all installations.
Single wall pipe is approved for residential installa-
tions only.
12 in.
Flashing
(305mm)
Minimum
*NOTE: Clearance to combustibles are for 1 inch
(25mm) clearance approved pellet pipe. If pellet pipe
has a 2 inch or 3 inch (51mm or 76mm) air clearance
to combustibles, increase the clearance from rear
standoff accordingly to meet pipe manufacturer clear-
ance requirements
Firestop
1 in. (25mm)
Minimum
6 in.
(152mm)
Min.
*See Note
0 in. (0mm) to
Standoff
Non-combustible
Hearth Extension
K. Through the Wall & Vertical - Exterior
Figure 44.1
Termination
Cap
12 in.
(305mm)
minimum
Flashing
Support
Bracket
0 in. (0mm) to Standoff
every 60 in.
(1524mm)
6 in. (152mm)
minimum
Wall Thimble
Tee
Clean-out
Cover
Non-combustible
Hearth Extension
Figure 44.2
Page 45
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
L. Through the Wall
NOTE:
Horizontal termination cap must be a minimum of 12 inches
(305mm) from the wall. Approved for mobile home installations.
Must use 3 or 4 inch (76mm-102mm) “L” or “PL” Listed pellet
venting and a Quadra-Fire Outside Air Kit in ALL installations.
In Canada, where passage through a wall or partition of
combustible construction is desired, the installation shall
conform to CAN/CSA-B365
Straight Out
0 in. (0mm) to Standoff
Horizontal
Wall
Thimble
Termination
Cap
6 in.
(152mm)
Minimum
From Glass
12 in.
(305mm)
Minimum
Non-combustible
Hearth Extension
Figure 45.1
NOTICE! See Section 8 “Avoiding Smoke and Odors” to minimize soot
damage to exterior walls of the house and to prevent re-entry of soot or ash
into the house for horizontal vent configuration
45 Degree
Illustration shows venting going in both directions.
Choose which one is best for your installation.
12 in. (305mm)
Minimum
12 in. (305mm)
Minimum
Wall
Thimble
1-1/6 in.( 27mm)
Minimum
1-16 in.
(27mm)
Minimum
Figure 45.2
Page 46
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Mobile Home Installation
9
WARNING! Risk of Asphyxiation!
CAUTION
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAIN-
TAINED
•
Never install in a sleeping room.
Consumes oxygen in the the room.
Do NOT cut through:
1. An outside air intake must be provided for the combus-
tion air and must:
•
•
Floor joist, wall, studs or ceiling trusses.
Any supporting material that would affect the structural
integrity.
• Remain clear of leaves, debris, ice and/or snow.
• Be unrestricted while the appliance is in use to pre-
vent room air starvation which causes smoke spill-
age.
This unit is to be connected to a factory-built chimney
conforming to CAN/ULC-S629, Standard for 650°C
Factory-Built Chimneys.
For removal of the chimney for mobile home transporta-
tion, contact the proper transportation officials.
• Smoke spillage can also set off smoke alarms.
2. The combustion air duct system must be made of metal
and it must:
• Permit zero clearance to combustible construction.
SparkArrestor Cap
• Prevent material from dropping into the inlet or into
the area beneath the dwelling.
• Must contain a rodent screen.
Storm Collar
3. The appliance must be secured to the mobile home
structure by bolting it to the floor. See page 33 for
detailed instructions on securing fireplace to the
floor.
Roof Flashing
4. The appliance must be grounded with #8 solid copper
grounding wire or equivalent, terminated at each end
with an NEC approved grounding device.
Joist Shield/Firestop
Approved Class L
or PL Pellet Vent
5. Refer to Clearances to Combustibles and floor protec-
tion requirements in Section 6 for listings to combus-
tibles and appropriate chimney systems.
6. Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the the exterior of the structure.
7. Follow the chimney manufacturer’s instructions when
installing the vent system for use in a mobile home.
Figure 46.1
8.
Installation shall be in accordance with the Manufacturers
Home & Safety Standard (HUD) CFR 3280, Part 24.
Page 47
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Appliance Set-Up
10
A. Optional Log Set Placement Instructions
2 PIECE LOG SET INSTALLATION
1. Place the left log as shown. There are 2 indentations in
the bottom of the log to fit over the screw heads in the
firebox. Figures 47.1 and 47.2.
Right Log
2. Place the right log in front of the 2 screw heads in the
firebox. Figures 47.3 and 47.4.
CAUTION! Logs are FRAGILE. Use extreme care when
handling or cleaning logs.
Log rests in front of screws
Figure 47.3
Left Log
Log fits over screws
Figure 47.1
Figure 47.4
Log has indentations on the
bottom to fit over the screw heads.
NOTICE:
Due to the abrasive nature of a pellet appliance fire, the logs
are not covered under warranty.
Any placement variation other than shown here can cause
excessive heat and shall void the appliance warranty.
Figure 47.2
Page 48
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Installing Front onto Mounting Frame
EDGE 60 Pellet Fireplace
B. Front - Installation
Included in Kit: Front, mounting frame, masonry spacer,
fasteners and glove
Hinges Aligned
Tools Required: Phillips Head screwdriver
CAUTION! BURN HAZARD. Allow the front to cool
before touching. Do NOT touch without wearing protective
glove.
Installing Mounting Bracket on Fireplace
1. Use a Phillips Head screwdriver and attach the mount-
ing frame to the face of the fireplace with 5 screws on
the top and bottom and 4 on each side. Figure 48.1
2. The front is attached to the mounting frame via the
hinges.
Figure 48.3
3. All 4 fronts are mounted the same way.
Push Up on
Spring Loaded
Hinge Pin
Front
Mounting
Frame
Figure 48.4
Figure 48.1
Push Locking Tab into
Place to Hold Hinge Pin
Hinge on Fireplace
Locking Tab
Hinge on Front
Start with Bottom Hinge
Alignment and then Top
Figure 48.5
Figure 48.2
Page 49
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Replacement Parts
11
B. Combustion (Exhaust) Blower
Replacement
A. Glass Replacement
WARNING! Risk of Injury!
1. Follow the proper shut down procedures as outlined on
• Glass is 5mm thick high temperature heat-resistant ceramic
glass.
page 14, Section 3.A
2. The combustion blower is mounted in the lower right
• DO NOT REPLACE with any other material.
• Alternate material may shatter and cause injury
rear of the appliance. Figure 49.2.
3. Use an 11/32 nut driver to loosen all six nuts, but do
not remove. Rotate the blower and remove from the
housing. Figure 49.3.
1. To remove the door:
a. Swing open the front.
4. Disconnect the wires.
b. Remove the door by lifting it off the hinge pins.
c. Lay on a flat surface face down.
5. You will also need to replace the gasket, see Parts List
for part number.
2. Using a Phillips head screwdriver, remove 4 screws, 2
on the top and 2 on the bottom. Figure 49.1.
6. Install replacement blower in reverse order and re-con-
nect the wires.
3. Remove metal bracket.
4. Remove the glass.
5. Replace with new glass with gasket.
6. Re-attach metal bracket with 4 screws.
7. Re-install door over hinge pins and close front.
Combustion Blower Located
Right Lower Side of Fireplace
Combustion Blower
Remove 4 screws
Figure 49.2
Loosen all 6 nuts, but do NOT Remove
Metal Bracket
Glass with Gasket
Figure 49.1
Figure 49.3
Page 50
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
D. Baffle Removal & Replacement
C. Convection Blower Replacement
WARNING! Risk of Injury! Cast iron is a very heavy
material. The baffle is made of cast iron and therefore is
heavy and awkward at times to maneuver. Clear and prepare
your work area before you begin.
1. Follow the proper shut down procedures as outlined on
page 14, Section 3.A.
2. Remove the 2 bolts from the bottom left and right side
of the fireplace and slide the fireplace out.
1. Follow the proper shut down procedures as outlined
3. Locate the convection blower on the bottom left rear of
the fireplace. Reach behind the blower and release the
latch by pushing the top of the latch towards the blower.
Figure 50.1.
on page 14, Section 3.A.
2. Open front and open firebox door.
3. The baffle is located at the top inside of firebox.
4. To remove the baffle:
4. Rock the top of the blower slightly and lift up and out.
The blower will pass around the control board and out
the side of the fireplace.
a. Place a flat head screwdriver into the slot of the
latches located in the upper corners. Figure
50.3.
5. Disconnect the wire harness from the bottom of the
blower by depressing the tabs on the sides of the con-
nector and then pulling to remove.
b. Push down and the bottom of the latch will fall
forward off of the post.
6. Re-connect wire harness to the new replacement
blower. Install the blower by placing the bottom flange
into the opening first then rotate blower up into posi-
tion.
c. Lift the baffle up and then out toward you.
5. To replace the baffle:
a. Place the 2 locating ears behind the bottom edge.
b. Tilt the baffle up and into place.
7. Whentheblowerisproperlypositionedthelatchwillengage
the notch to hold the blower in place. Figure 50.2.
The baffle must be centered in the firebox before
latching it in place.
8. Slide appliance back in position and re-install bolts.
c. If it is not centered the latch is trapped between
the baffle and side of the firebox instead of latch-
ing properly.
d. The bottom of the latches will fit over the posts.
Release the Latch
e. Push the top of the latch forward to lock latch into
place.
Baffle
Figure 50.1
Latches
Locating ears - 1 on
each side. Fit behind
bottom edge.
Insert flat head screw driver into “V”
section and push down and the bottom
of the latch will fall forward off of post
Figure 50.3
Figure 50.2
December 6, 2011
Page 51
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
With proper installation, operation, and maintenance your appli-
ance will provide years of trouble-free service. This trouble-
shooting guide shall be used by a qualified service technician
only).
Troubleshooting For Installers
12
Possible Cause
Corrective Action
Error Message
Bad wall control or control board
Replace wall control or control board
3 wires have loose connections or installed
wrong
Check connections
BAD TC DROP TUBE
Drop tube thermocouple is broken or leads are Check connections
reversed
(TC = Thermocouple)
Replace thermocouple
BAD TC FIREPOT
Firepot thermocouple is broken or leads are
reversed
Check connections
(TC = Thermocouple)
Replace thermocouple
SNAP DISC TRIPPED
Overheat sensor (snap disc) has tripped
Turn power off to appliance and manually
reset snap disc then turn power back on
Clean convection blower if needed
Convection blower may need cleaning
Vacuum switch is bad
VACUUM SW ERROR
Check connections. Bypass vacuum with
jumper wire, if runs, switch is bad. Replace
switch
(SW = Switch)
Check vacuum hose
Vacuum hose is plugged/disconnected
COMB BLOWER JAMMED Combustion blower is blocked/jammed
Remove blockage
Replace blower if necessary
Turn the power switch OFF and then back
ON to clear the error
AUGER JAMMED
MISSED IGNITION
Auger jammed, feed motor bad
Pull the feed system and inspect
Clear jam and Press Retry
Igniter bad or poor harness connection
Out of fuel or fuel is bridging in hopper
Check connections, if OK replace igniter
Break up bridging pellets. Refill hopper
Faulty firepot thermocouple connection has
shorted.
Replace the thermocouple
Press Retry
MIN FIREPOT TEMP
Out of fuel
Refill hopper
Add handful of pellets to firepot to prime it
Press Retry
MAX DROP TUBE TEMP
Stove in over-heat condition
Flame height set too high
Confirm setting matches burning fuel
Adjust flame height
Components may need cleaning
Clean the firebox, heat exchanger, convec-
tion blower, firepot and ash pan
CONV BLOWER JAMMED
CHECK ASHPAN
Convection blower blocked/jammed
Remove blockage
Replace blower if necessary
Turn the power switch OFF and then back
ON to clear the error
Auto-clean jammed
If ashpan is empty, check for a jam. Use a
screw driver and firmly push in the firepot
floor holes and flex spring and push toward
home to release jam
Auto-clean switch is bad
Replace switch
Linkage has become disconnected
Reconnect linkage
SCREEN GOES BLANK
Static discharge or nearby lightning or
Electric fast transients at the input mains
Power switch in OFF position
Wait 25 seconds and press any key to
refresh the screen.
Turn to ON position
Hopper lid not closed all the way
Close the lid. If that didn’t work replace the
switch
Switch is out of adjustment (auger will not
function)
Adjust or replace switch
Firebox door is not latched properly
Fireplace not rolled in completely
Slide rail bolts not installed
Out of fuel
Adjust or replace door switch
Replace interlock switch or magnet
Install bolts
Check fuel level, if OK the switch may be
out, replace switch
Page 52
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
Reference Materials
13
A. Fireplace Dimensions
Front View
(shown without a Front)
Top View
Rear View
9-1/4 in.
(235mm)
26 in.(660mm)
Rear Vent
3/4 in.
(19mm)
9-1/4 in.
(234mm)
3/4 in.
(19mm)
C
Top Vent
L
C
L
29 in.
(737mm)
26-7/8 in.
(682mm)
C
L
Outside Air
4-7/8 in.
(24mm)
9-1/4 in.
(235mm)
Left Side View
Right Side View
3/4 in.
(19mm)
Front
Front
Junction Box
37-1/2 in.
(953mm)
C
L
C
L
21-3/8 in.
(543mm)
Outside
Air
Outside Air
C
C
L
L
16-1/2 in.
(419mm)
C
L
C
L
C
L
4-7/8 in.
(125mm)
4-7/8 in.
(124mm)
1-3/4 in.
(44mm)
14-1/4 in.
(362mm)
1-3/4 in.
(44mm)
Page 53
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
When describing the location of a component,
it is always AS YOU FACE THE FRONT OF
THE APPLIANCE.
B. Component Functions
1. Auto-Clean Motor
9. Firepot
Location: Behind and under the firepot on the left side, inside
the convection air chamber
Location: Inside firebox and is made of high quality ductile
iron.
Function: It automatically opens and closes the firepot floor
so ashes can fall into the ash pan.
Function: The floor of the firepot automatically opens for
cleaning and is operated by the auto-clean firepot system.
The floor needs to return to a completely closed position or
the appliance will not operate properly.
2. Auto-Clean Switch
Location: On top of the auto-clean motor
Function: Communicates to the control board when the firepot
floor is open and when the auto-clean system has completed
its cycle and is back in the home (closed) position.
10. Fuses
Location: One AC fuse and one DC fuse is located on the
inside of the control board and a third fuse is located in the
power supply. Figures 54.1 & 54.2 on page 54.
3. 12 Volt Battery Back-Up Cable (Optional Accessory)
Location: Plugs into the appliance at the lower left front of
the appliance.
Function: The AC fuse operates the igniter and the DC
fuse operates all of the other components. The third fuse
protects the components in the power supply. A fuse will
blow should a short occur and shut off power to the appli-
ance. The fuses can only be replaced by an authorized
dealer.
Function: An icon will display on the wall control when the
appliance has lost main power and is running on battery
back-up.
4. Combustion (Exhaust) Blower
11. Heat Exchanger
Location: Mounted in the bottom right rear of appliance.
Location: Behind the baffle. Remove the cast iron baffle
to access the heat exchanger.
Function: Pulls the exhaust from the appliance and pushs it
out through the venting system.
Function: Transfers heat from the exhaust system into the
convection air chamber.
5. Control Board
Location: Lower left side of appliance.
12. Hopper Lid Switch
Function: Controls the functioning of the appliance and
communicates with the wall control. The control board can
only be opened by an authorized dealer.
Location: Lower front right side of appliance on the power
switch cover.
Function: Senses whether the hopper lid is open and dis-
plays an icon on the wall control and will turn off the feed
motor.
6. Convection Blower
Location: Mounted at the bottom left rear of the appliance
Function: Pushes heated air through the heat exchange
system into the room.
13. Interlock Switch
Location: Lower front right side of appliance behind power
switch.
7. Door Switch
Location: Mounted on the right side of the firebox behind
the door handle
Function: Causes the auger to stop functioning and will be
opened when the appliances slides are extended.
Function: Senses when the door is open and will display an
icon on the wall control and will turn off the auto-clean system
and feed motor for safety.
14. Igniter (Heating Element)
Location: Mounted on the base of the firepot.
Function: Combustion air travels over the red hot igniter
creating super heated air that ignites the pellets or other
fuels.
8. Feed System
Location: On the right side of the appliance and can be
removed as an entire assembly. The assembly includes
the feed motor, mounting bracket, bearing and feed spring
(auger).
15. Power Receptacle
Location: Lower rear of the appliance
Function: The hollow feed spring (auger) pulls pellets up the
feed tube from the hopper area and drops them down the
feed chute into the firepot
Function: Check the wall receptacle for 120 volt, 60 Hz
(standard current). Make sure the outlet is grounded and
has the correct polarity.
Page 54
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
16. Power Supply
20. Thermocouple - Drop Tube
Location: At the rear of the appliance
Location: Bottom of the drop tube on the right side and
Function: Converts 120 volt AC current to 15 volt DC current to
attached with a wing nut
power the appliance.
Function: Turns the convection blower on and off, varies
the speed of the convection blower and will shut down
appliance if internal heat exceeds set temperature.
17. Power Switch
Location: Lower front right side of appliance
Function: Turns the power on and off to the appliance
21. Vacuum Switch
Location: Right side of the appliance under the feed
motor behind right side panel and connects to the drop
tube with a hose
18. Overheat Sensor (Snap Disc)
Location: Mounted on the back of the drop tube in the center
of the appliance and has a reset button. Remove the right side
panel to access.
Function: Turns the feed system on when vacuum is
present in the firebox. The vacuum switch is a safety
device to shut off the feed motor if the exhaust or the
heat exchanger system is dirty, plugged or if the firebox
door is open.
Function: If the fire tries to burn back into the feed system or
push exhaust up the feed tube, this sensor will shut the appli-
ance down, however the wall control will still display messages.
This sensor must be manually re-set. Disconnect power before
resetting.
22. Wall Control, Thermostat
Location: Interior wall of the home
19. Thermocouple - Firepot
Function: The appliance is designed to run on a custom
designed 3.3 volt DC thermostat wall control. It will not
operate on any other wall control. Refer to the instruc-
tions supplied with the appliance, located in the compo-
nent pack.
Location: On top of the firepot inside the thermocouple cover
(ceramic protection tube)
Function: Sends a millivolt signal to the control board telling the
control board there is a fire in the firepot.
23. Wiring Schematic for Power Supply
See Figure 54.1 below.
24. Wiring Schematic for Control Board
See Figure 54.2 below.
Heat sinks are taped to cover for
shipping. Slowly lift cover and cut the
n/a
6
13 12
11
10
9
5
8
7
tape holding them in place and then
you can remove the cover.
Fuse 15A 250V
(need to remove
4
cover)
3
2
Fuse 15A 120V,
under the cover
14
1
Fuse 15A 120V,
under the cover
120V AC out to
Control Board
15V DC out to
Control Board
120V AC in
15
16
17
Figure 54.1 - Power Supply
Figure 54.2 - Control Board
Control Board Schematic
#
Description
#
7
8
9
Description
Thermostat Wall Control
Combustion Blower (feedback)
Firepot Thermocouple
#
Description
1
Combustion Blower
12 Igniter
2
3
4
5
6
Auto-Clean System
Feed/Auger Motors
Hopper/Door Switches
13 AC Power In for Igniter
14 Convection Blower Power
15 Overheat Sensor (Snap Disc)
16 DC Power In from Power Supply
10 Drop Tube Thermocouple
Auger/Auto Clean/Vacuum Switches n/a Not Used
Low Fuel 11 Convection Blower (feedback)
17
12 Volt Battery Back-up
Page 55
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
C. Component Locations
Hopper
Exhaust
Transition
Exhaust
Feed Motor
with Gasket
Convection
Blower
Battery
Backup
Outside Air Intake
w/Gasket (left side)
Combustion
Blower
Power
Supply
Figure 55.1 - View of Left Rear
Figure 55.2 - View of Right Rear
Heat Exchanger,
Front & Back
One bolt located on each side of fireplace
Baffle
Pull fireplace toward you until
fully extended
Slide Rails
Ash Pan
Firepot
Thermocouple and
Thermocouple Cover
Figure 55.3 - Rail System
Figure 55.4
Page 56
7051-158B
December 6, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
R
EDGE 60 Pellet Fireplace
F. Service And Maintenance Log
Date of Service
Performed By
Description of Service
Page 63
December 6, 2011
7051-158B
Download from Www.Somanuals.com. All Manuals Search And Download.
R
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
visit our web site at www.quadrafire.com
NOTICE
DO NOT DISCARD THIS MANUAL
•
Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
•
Leave this manual with
party responsible for use
and operation.
• Important operating and
maintenance instruc-
tions included.
We recommend that you record the following pertinent
information for your EDGE 60 PELLET FIREPLACE
Date purchased/installed:
Serial Number:
Location on appliance:
Dealer phone:
Dealership purchased from:
Notes:
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534,
5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099,
6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441,
6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264,
2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
7051-158B
December 6, 2011
Page 64
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Ricoh All in One Printer JP5000 User Guide
Roland Musical Instrument HandSonic 10 User Guide
Rubbermaid Outdoor Storage P0 5L20 P0 User Guide
Samsung All in One Printer SL C460FW User Guide
Samsung Home Theater System HT E550 User Guide
Samsung Laptop Q35 User Guide
Samsung Security Camera SSC C6433 User Guide
Schumacher Battery Charger SE 6242A User Guide
Sears Snow Blower 486248392 User Guide
Senco Nail Gun SCN125 User Guide