Sanyo Security Camera VCC ZM400 User Guide

INSTRUCTION MANUAL  
MANUEL D’INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
VCC-ZM400  
COLOR CCD ZOOM camera  
Caméra CCD COULEURS avec ZOOM  
Cámara CCD ZOOM A COLOR  
About this manual  
Before installing and using the camera, please read this manual  
carefully. Be sure to keep it handy for later reference.  
Acerca de este manual  
Lea cuidadosamente este manual antes de instalar y usar  
la cámara. Asegúrese de guardarlo a su alcance para  
futuras consultas.  
À propos de ce manuel  
Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel  
attentivement. Gardez-le à portée de main pour toute référence  
ultérieure.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INFORMATION TO USER  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
Safety Guard  
These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications.  
THIS SYMBOL INDICATES THAT THERE ARE  
IMPORTANT OPERATING AND MAINTENANCE  
INSTRUCTIONS IN THE LITERATURE  
ACCOMPANYING THIS UNIT.  
WARNING:  
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or  
more of the following measures:  
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and  
receiver.  
For the customers in Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
– Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Pour la clientèle canadienne  
Cet appareil numerique de la Classe B est conforme à la  
norme NMB-003 du Canada.  
– Consult the dealer or an experienced radio/TV technician for  
help.  
This device complies with Part 15 of the FCC Rules. Operation  
is subject to the following two conditions: (1) This device may  
not cause harmful interference, and (2) this device must  
accept any interference received, including interference that  
may cause undesired operation.  
This installation should be made by a qualified service person and  
should conform to all local codes.  
Changes or modifications not expressly approved by Sanyo  
may void the user’s authority to operate this camera.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
In case of problem  
Protect from high temperatures  
Do not use the camera if smoke or a strange odour comes from  
the unit, or if it seems not to function correctly. Disconnect the  
power cord immediately, and consult your dealer (or a Sanyo  
Authorized Service Centre).  
Do not install close to stoves, or other heat generating devices,  
such as spotlights, etc., or where it could be subject to direct  
sunlight, as that could cause deformation, discoloration or other  
damages.  
Be careful when installing close to the ceiling, in a kitchen or  
boiler room, as the temperature may raise to high levels.  
Do not open or modify  
Do not open the cabinet, as it may be dangerous and cause  
damage to the unit. For internal settings and repairs, consult your  
dealer (or a Sanyo Authorized Service Centre).  
Install where the temperature range will stay between –10°C and  
50°C. (no condensation)  
Cleaning  
Do not put objects inside the unit  
Dirt can be removed from the cabinet by wiping it with a soft  
cloth. To remove stains, wipe with a soft cloth moistened with  
a soft detergent solution and wrung dry, then wipe dry with a  
dry soft cloth.  
Make sure that no metal objects or flammable substance get  
inside the camera. If used with a foreign object inside, it could  
cause a fire, short-circuits or damages.  
If water or a liquid gets inside the camera, disconnect the power  
cord immediately, and consult your dealer (or a Sanyo Authorized  
Service Centre). Be careful to protect the camera from rain, sea  
water, etc.  
Do not use benzine, thinner or other chemical product on the  
cabinet, as that may cause deformation and paint peeling.  
Before using a chemical cloth, make sure to read all  
accompanying instructions. Make sure that no plastic or  
rubber material comes in contact with the cabinet for a long  
period of time, as that may cause damage or paint peeling.  
Be careful when handling the unit  
To prevent damages, do not drop the camera or subject it to  
strong shock or vibration.  
Install away from electric or magnetic fields  
If installed close to a TV, radio transmitter, magnet, electric motor,  
transformer, audio speakers the magnetic field they generate will  
distort the image.  
Protect from humidity and dust  
To prevent damages to the camera, do not install it where there is  
greasy smoke or steam, where the dampness may get too high,  
or where there is a lot of dust.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS NAMES AND FUNCTIONS  
4 SET button (SET) (See p8)  
Control  
3
Connect the camera to the monitor, then press the SET  
button for about 3 seconds to display the on-screen menu.  
5 RS-485 control push-lock terminals (RS485, A, B, G)  
terminals  
SET  
4
Use a cable thicker than AWG22.  
IN  
ZOOM  
COM  
OUT  
FOCUS  
ALARM  
RS485  
2
1
A: Twisted-pair cable terminal  
G: Ground terminal  
VIDEO OUT  
POWER  
AC24V  
B: Twisted-pair cable terminal  
5
6
A
GND  
B
G
6 24 V AC or 12 V DC input terminals (AC 24 V, DC 12 V,  
GND)  
DC12V  
CLASS 2 WIRING  
Lens cap  
1 Video output connector (VIDEO OUT: BNC type)  
The cap is installed to protect the lens section. Remove the cap  
when using the camera.  
Connect this connector to a device such as a time lapse VCR or  
monitor with a VIDEO IN connector.  
2 Power indicator (POWER)  
Comes on when the power to the camera is on.  
Note: After connecting the power supply the POWER indicator  
will blink for 5 seconds. During this time no adjustments  
using the menus or any other operation are possible.  
3 Cursor button (See p8)  
j: Press this button to move the cursor up.  
c: Press this button to move the cursor to the right, or to  
turn the settings ON/OFF etc.  
d: Press this button to move the cursor to the left, or to turn  
the settings ON/OFF etc.  
l: Press this button to move the cursor down.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS NAMES AND FUNCTIONS  
Camera installation bracket  
Control terminals  
The bracket can be fixed at the top or bottom of the camera.  
1 Zoom terminal (ZOOM)  
Sets the zoom to wide angle or telescoping.  
2 Focus terminal (FOCUS)  
CAUTION: When installing the camera bracket, select a location  
that can support the total weight of the camera and  
accessories.  
Sets the focus to infinite or close range.  
3 Grounding terminal (COM)  
4 Alarm output terminal (ALARM OUT)  
A detection alarm based on the motion sensor is sent to  
connected equipment such as a buzzer or lamp or a time  
lapse VCR device.  
5 Alarm input and color/black & white selection  
terminal (ALARM IN)  
When using this terminal for alarm input, connect an  
external alarm switch for detecting intruders.  
This terminal can also be used for selecting color or black &  
white input. It can be used to force selection of color or  
black & white mode by external operation.  
Note: The ALARM IN terminal can only receive one type of  
input at a time. When using this terminal, use the  
ALARM settings to set the type of input. (See p57)  
12345  
ZOOM  
COM IN  
FOCUS  
ALARM OUT  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Basic connection for monitoring or recording  
TV monitor  
(sold separately)  
AC 24 V connection  
DC 12 V connection  
(A)  
AC24V  
AC24V  
GND  
GND  
DC12V  
CLASS  
2
WIR  
DC12V  
CLASS  
2
WIR  
Fig. 1  
Fig. 2  
(Video signal connections)  
Time lapse VCR or  
: VIDEO IN  
Digital video recorder  
: VIDEO OUT  
(sold separately)  
The peripheral devices (VCR, monitor, lens, etc.) and cables  
are sold separately.  
CAUTION:  
To prevent camera and/or power supply failure, pay close  
attention to polarity when making the connections.  
1 Make the video signal connection between the camera  
and the monitor or time lapse VCR.  
2 Power supply choices  
3 Insert the plug of this power supply into a wall outlet.  
When using a commercially available 24 V AC adaptor,  
make sure to use a cable with an earth line (22AWG or  
more) to connect to the grounding terminal. (Fig.1.)  
The POWER indicator (A) will light. Adjust the picture on the  
monitor using the Brightness and Contrast controls.  
When using a DC 12 V power supply, make the  
connections as indicated in Fig. 2.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Coaxial cable type and maximum length  
Cable type RG-59U (3C-2V), 250 m maximum.  
Cable type RG-6U (5C-2V), 500 m maximum.  
Cable type RG-11U (7C-2V), 600 m maximum.  
Connection of peripheral equipment and  
controller terminal  
External alarm  
switch or color/  
black & white select  
switch  
CAUTION:  
Buzzer or lamp  
The RG-59U type cable should not be run through electrical  
conduits or through the air.  
• Focus adjustment  
DC+6V/12V: Infinite  
DC–6V/12V: Close range  
Using CCTV/Video-grade coaxial cable.  
• Zoom adjustment  
DC+6V/12V: Wide angle  
DC–6V/12V: Telescoping  
G
A B  
CAMERA IN  
terminal  
Multiplexer  
(sold separately)  
GAB  
RS-485 connector  
System controller (sold separately)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISPLAYING/CLOSING THE MENU SCREEN  
MAIN MENU screen  
Sub-menu screen  
MAIN MENU  
LANGUAGE  
LANGUAGE  
CAMERA ID  
SYNC  
SET ‚  
OFF  
LANGUAGE  
ENGLISH  
FRENCH  
SET  
LANGUE  
IDIOMA  
INT  
SPANISH  
PRIVACY MASK  
LENS  
SET ‚  
SET ‚  
OFF  
MIRROR  
VIEW SETTING  
OPTION  
1
SET ‚  
OFF  
PRESET  
MENU  
END  
MENU  
BACK  
Cursor button SET button  
1 Press the SET button for about 3 seconds.  
3 Switching to sub-menu screens  
The MAIN MENU screen will appear.  
Use the cursor button (j l d c) until an item with a “y”  
next to it is flashing, then press the SET button.  
2 Using the cursor button  
4 Closing a settings screen  
1 Use the cursor button (l) to move the cursor down.  
When the cursor reaches the bottom of the screen, it goes  
back up to the top of the screen.  
To return to the previous screen, use the cursor button (l)  
to select BACK for MENU, then press the SET button.  
2 Use the cursor button (j) to move the cursor up. When  
the cursor reaches the top of the screen, it goes back  
down to the bottom of the screen.  
To return to the normal screen, use the cursor button (d or  
c) to select END for MENU, then press the SET button.  
Returning to the default setting  
Use cursor button (l, then d or c) to change the PRESET  
setting to ON, then press the SET button.  
3 Use the cursor button (c) to move the cursor to the right.  
This button is also used to change ON/OFF settings etc.  
4 Use the cursor button (d) to move the cursor to the left.  
This button is also used to change ON/OFF settings etc.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU ITEM FLOW AND MENU OPERATION  
MAIN MENU  
1 2 3 4 5 6 7 8  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
MIRROR  
VIEW SETTING  
OPTION  
PRESET  
MENU  
1
LANGUAGE setting (See p10)  
6
MIRROR setting (See p32)  
Choose from among English, French and Spanish.  
The image can be rotated horizontally then vertically or vertically  
then horizontally.  
2
3
CAMERA ID setting (See p11)  
SYNC setting (See p12)  
7
VIEW SETTING (See p33)  
Different detailed settings can be made for each camera (9  
screens). After they are set, these are linked to “VIEW SETTING  
(0 – 8)” settings for preset positions.  
Sets camera to internal synchronization (INT) or power source  
synchronization (L-L).  
Power source synchronization, the vertical synchronization phase  
as adjusted on a sub-menu screen.  
8
OPTION setting (See p56)  
For setting communications conditions and alarms.  
4
PRIVACY MASK setting (See p13)  
This covers an area of the screen with a gray pattern for areas  
that may infringe on privacy.  
Gray patterns can be placed on up to 4 areas.  
5
LENS setting (See p17)  
This lets you make settings such as automatic and manual focus  
settings, zoom speed and zoom ratio. In addition, it can also be  
used for automatic switching to color images during daytime, or  
to black and white images at times of low luminance such as  
nighttime.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
LANGUAGE SETTING  
Select one of the languages shown on the menu screen (English, French, Spanish).  
1
MAIN MENU  
2
LANGUAGE  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
LANGUAGE  
ENGLISH  
FRENCH  
SPANISH  
LANGUE  
IDIOMA  
PRIVACY MASK  
LENS  
MIRROR  
VIEW SETTING  
OPTION  
3
LANGUE  
PRESET  
LANGUAGE  
LANGUE  
ANGLAIS  
FRANCAIS  
ESPAGNOL  
MENU  
IDIOMA  
MENU  
RETOUR  
1 In the MAIN MENU, use the cursor button (j or l) to  
select SET for LANGUAGE, then press the SET button.  
The LANGUAGE screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
language (e.g. FRENCH) then press the SET button.  
The interface language becomes French.  
3 Use the cursor button (j or l) to select RETOUR for  
MENU, then press the SET button.  
The MENU PRINCIPAL screen will reappear.  
Information in the MAIN MENU screen will appear in the  
selected language.  
Use the cursor button (l) to select FIN, then press the  
SET button. The display will return to the normal  
monitor screen.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA ID SETTING  
Camera ID setting  
Camera ID screen  
Example: Setting the Camera ID to “CAM 1”  
CAMERA ID SETTING  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
0123456789 :-‚  
1
MAIN MENU  
2
CAMERA ID SETTING  
1
LANGUAGE  
CAMERA ID  
SYNC  
SET  
ON  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
0123456789 :-‚  
ID ????????????????  
-
2
3
4
PRIVACY MASK  
LENS  
POSITION  
SET  
ID ????????????????  
-
MIRROR  
PRESET  
MENU  
OFF  
BACK  
VIEW SETTING  
OPTION  
POSITION  
SET  
PRESET  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Character selection palette:  
By moving the cursor to letters or numbers in this palette,  
you can select characters.  
1 Use the cursor button (j or l) to move the cursor to  
CAMERA ID, and then use the cursor button (d or c) to  
change the setting to ON. Then press the SET button.  
Selected characters will appear in the corresponding field  
under ID.  
The CAMERA ID SETTING screen will appear.  
2 ID:  
2 Use the cursor button (j l d c) to move the cursor to  
the letter “C” in the character selection palette, then  
press the SET button.  
When CAMERA ID is set to “OFF”, the 16 characters in the  
ID field will all change to “?” but will not be displayed on  
the screen. In addition, when the setting is “ON”, “?”  
characters will appear on the screen when no ID has been  
entered.  
After at least one character is displayed in the ID field,  
the carriage return mark (y) will appear at the lower  
right corner of the character selection palette. Selecting  
this mark between the characters of the field will create  
a new line at that place.  
3 POSITION:  
After characters are displayed in the ID field, moving the  
cursor to the POSITION field with the cursor button and  
pressing the SET button will display the camera ID on the  
normal screen.  
3 Use the same steps to select “A”, “M” and “1” from the  
palette, then press the SET button.  
4 PRESET:  
The characters “CAM1” appear in the ID field.  
When this item is turned to ON, the ID fields are cleared  
(question marks appear). Use this function when you want  
to change the ID.  
ID CAM1????????????  
-
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA ID SETTING  
SYNC SETTING (SYNC)  
Default setting is internal synchronization (INT), so it does not  
need to be set again. Follow the steps below to change the  
setting to power source synchronization (L-L).  
4 Use the cursor button (j or l) to move the cursor to  
POSITION, and then press the SET button.  
The camera ID will be displayed on one line.  
Power source synchronization (L-L) setting  
CAMERA ID SETTING  
CAM1  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
0123456789 :-‚  
1
MAIN MENU  
2
L-L SETTING  
(V SYNC PHASE)  
ú------+------ü  
Camera ID  
ID CAM1????????????  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
POSITION  
SET  
0
PRESET  
MENU  
OFF  
BACK  
PRIVACY MASK  
LENS  
MIRROR  
VIEW SETTING  
OPTION  
(Displaying the ID on 2 lines.)  
PRESET  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (d or c) to move the cursor to the  
location in the ID field where the carriage return is wanted.  
1
Use the cursor button (j l d c) to select L-L for  
SYNC, then press the SET button.  
The L-L SETTING screen will appear.  
2 Use the cursor button (j l d c) to move the cursor to  
the carriage return mark (y) at the lower right corner of  
the character selection palette, and then press the SET  
button.  
2
Use the cursor button (d or c) to adjust the position  
of the vertical synchronization indicator shown on the  
screen.  
The numerical value will change, allowing adjustment of  
vertical synchronization.  
5 Moving the on-screen title display position  
Use the cursor button (j l d c) to move the title  
display to the preferred position on the screen, then  
press the SET button.  
The CAMERA ID SETTING screen will reappear.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRIVACY MASK SETTING (PRIVACY MASK)  
Mask setting  
1
MAIN MENU  
2
PRIVACY MASK SETTING  
PASSWORD LOCK ON ‚  
3
MASK NO.SELECT  
MASK 3 SET  
(POSITION)  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
MASK  
MASK  
MASK  
MASK  
1
2
3
4
OFF  
OFF  
SET  
OFF  
MIRROR  
VIEW SETTING  
OPTION  
MASK NO.SELECT  
OFF  
PRESET  
MENU  
PRESET  
MENU  
OFF  
BACK  
SET  
MASK  
MASK  
MASK  
MASK  
1
2
3
4
OFF  
OFF  
OFF  
1 Use the cursor button (j or l) to select SET for  
3 Use the cursor button (j or l) to move the cursor to a  
mask number (e.g. MASK 3), and then use the cursor  
button (c) to change the setting to SET. Then press the  
SET button.  
PRIVACY MASK, then press the SET button.  
The PRIVACY MASK SETTING screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
The MASK 3 SET (POSITION) screen will appear, and SETy  
will be blinking. The gray mask will appear in the center of the  
screen.  
SET for MASK SET and press the SET button.  
The MASK NO. SELECT screen will appear.  
Cursor button operation  
Note: When PASSWORD LOCK is ON, moving the cursor to  
MASK SET and press the SET button to bring up a  
password access screen. The password must be entered in  
this screen.  
OFF: to c side (ON appears), to c side again (SET appears)  
SET: Mask POSITION and SIZE can be set  
ON: Masks can be displayed  
OFF: Masks can be deleted  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRIVACY MASK SETTING (PRIVACY MASK)  
(About the POSITION screen)  
4
MASK 3 SET  
(SIZE)  
5
MASK 3 SET  
It is possible to set as many as 4 masks on the same POSITION  
screen.  
MASK 1  
2
SET  
PRESET  
MENU  
OFF  
BACK  
4 Use the cursor button (j l d c) to move the gray  
mask, then press the SET button.  
The SIZE screen will appear, and the mask that was positioned  
in the POSITION screen will be displayed.  
3
4
5 Use the cursor button (j l d c) to adjust the size of  
the gray mask, then press the SET button.  
PRESET and MENU will appear at the bottom of the screen.  
Move the cursor to BACK for MENU and press the SET button.  
The screen will return to MASK NO. SELECT.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRIVACY MASK SETTING (PRIVACY MASK)  
PASSWORD setting  
You can lock the privacy masks in place as gray patterns after they have been set. The password requirement is initially set to OFF, but to  
begin using it, you must enter the factory set password “1234”.  
1
PRIVACY MASK SETTING  
PASSWORD LOCK OFF ‚  
PASSWORD  
3
PASSWORD  
PRIVACY MASK SETTING  
PASSWORD LOCK ON  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
¤¤¤¤  
-
SET ‚  
1234  
-
SET ‚  
BACK  
OK  
MENU  
BACK  
MENU  
BACK  
MENU  
MENU  
BACK  
1 Use the cursor button (j or l) to move the cursor to  
OFF for PASSWORD LOCK in the PRIVACY MASK  
SETTING screen. Then press the SET button.  
3 Use the same steps to enter “2”, “3” and “4”, then press  
the SET button.  
OK” will appear and BACK for MENU will be blinking. Press  
the SET button again. The PRIVACY MASK SETTING screen  
will reappear and “ON” will be blinking for PASSWORD LOCK.  
The PASSWORD screen will appear.  
2 Enter the factory set password “1234”.  
Use the cursor button (j or l) to select “1”, then use  
Note: If a different password is required, “NG” will appear.  
Please carefully maintain the password so that it will not be  
forgotten.  
the cursor button (c).  
To move the cursor to the next “*” digit.  
1¤¤¤  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRIVACY MASK SETTING (PRIVACY MASK)  
PASSWORD LOCK cancellation  
PASSWORD changes  
For use when PASSWORD LOCK is ON  
You can change the password with PASSWORD LOCK in either  
the ON or OFF setting.  
1
PASSWORD  
3
PASSWORD  
1
PRIVACY MASK SETTING  
PASSWORD LOCK ON  
2
PASSWORD  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
(NOW PASSWORD)  
¤¤¤¤  
-
SET ‚  
BACK  
1234  
-
SET ‚  
1234  
-
SET ‚  
OK  
MENU  
PASSWORD  
PASSWORD  
PRIVACY MASK SETTING  
PASSWORD LOCK OFF ‚  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
(NOW PASSWORD)  
**** SET ‚  
(NEW PASSWORD)  
****  
SET ‚  
-
-
1 Press the SET button.  
1 Use the cursor button (j or l) to move the cursor to  
SET for PASSWORD CHANGE and press the SET button.  
The PASSWORD screen will appear.  
The PASSWORD (NOW PASSWORD) screen will appear.  
2 Enter the factory set password “1234”.  
2 Use the cursor button (d or c, j) to enter the current  
Use the cursor button (j or l) to select “1”, then use  
password (e.g. 1234), then press the SET button.  
the cursor button (c).  
The PASSWORD (NEW PASSWORD) screen will appear.  
To move the cursor to the next “*” digit.  
3 Use the cursor button (d or c, j) to enter a new  
3 Use the same steps to enter “2”, “3” and “4”, then press  
password (e.g. 4321), then press the SET button.  
the SET button.  
OK” will appear and BACK for MENU will be blinking. Press  
the SET button again.  
The PRIVACY MASK SETTING screen will reappear.  
OK” will appear and BACK for MENU will be blinking. Press  
the SET button again. The PRIVACY MASK SETTING screen  
will reappear and “OFF” will be blinking for PASSWORD LOCK.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING ITEM FLOW  
A FOCUS: (See p18)  
MAIN MENU  
These settings let you select automatic focus (AUTO) or manual focus. Change the focus settings in  
accordance with the monitoring conditions.  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
PRIVACY MASK  
LENS  
B ZOOM: (See p21)  
MIRROR  
VIEW SETTING  
OPTION  
These settings let you adjust the speed and zoom ratio when using electronic zoom.  
PRESET  
MENU  
C DAY/NIGHT: (See p23)  
These settings can be used for automatic switching to color images during daytime, or to black and  
white images at times of low luminance such as nighttime. Three modes (AUTO, COLOR and B/W) can  
be selected. Change the settings in accordance with the monitoring conditions.  
A
B
C
D
LENS  
FOCUS  
MANU ‚  
SET  
D VIEW ANGLE: (See p31)  
ZOOM  
These settings are for setting the image angle.  
If “OVER” is set, the image angle is set to approximately 1.05.  
DAY/NIGHT  
VIEW ANGLE  
AUTO ‚  
OFF  
PRESET  
MENU  
OFF  
BACK  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
This item allows adjustment of focus (for manual focus or autofocus) and adjustment of zoom when needed.  
A FOCUS setting  
Setting the manual focus (MANU)  
Sets a limit for near distance focusing and sets focus speed for manual focus.  
FOCUS SETTING  
FOCUS SETTING  
1
MAIN MENU  
2
FOCUS SETTING  
3
4
LIMIT NEAR  
SPEED  
3M  
2
LIMIT NEAR  
3M  
3
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
LIMIT NEAR  
1M  
2
SPEED  
SPEED  
LENS  
FOCUS  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MANU ‚  
SET  
ZOOM  
1 Use the cursor button (j or l) to select SET for LENS,  
4 SPEED of focus setting  
then press the SET button.  
Use the cursor button (j or l) to move the cursor to  
SPEED, then use the cursor button (d or c) to select the  
focus adjustment speed value. (e.g. 3)  
The LENS screen will appear.  
2 Use the cursor button (d or c) to select MANU, then  
press the SET button.  
Available settings: 1, 2, 3, 4 (Quickest speed)  
The FOCUS SETTING screen will appear.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
3 LIMIT NEAR focus distance setting  
Use the cursor button (j or l) to move the cursor to  
LIMIT NEAR, then use the cursor button (d or c) to  
change the distance value. (e.g. 3M)  
Available settings: 1M (meter), 3M, 10C (centimeters), 30C,  
50C  
Note: Focusing becomes difficult when near distance limit is set  
to less than “1M”.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
Setting the autofocus (AUTO)  
Sets a limit for near distance focusing and sets focusing sensitivity and focus target area.  
Note: As a normal practice, use manual focus when keeping the camera focused on the same target object for a long period of time  
(over 24 hours). This can be used with the one-push autofocus function when needed (operated from the system controller). Long  
periods of surveillance with the autofocus in operation will shorten the work life of the lens.  
1
MAIN MENU  
2
LENS  
3
FOCUS SETTING  
4
FOCUS SETTING  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
LIMIT NEAR  
SENSITIVITY  
AREA  
3M  
HIGH  
SET  
FOCUS  
ZOOM  
AUTO ‚  
LIMIT NEAR  
SENSITIVITY  
AREA  
3M  
LOW  
SET  
SET  
MIRROR  
FOCUS SETTING  
VIEW SETTING  
OPTION  
LIMIT NEAR  
SENSITIVITY  
AREA  
1M  
PRESET  
MENU  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
HIGH  
SET  
1 Use the cursor button (j or l) to select SET for LENS,  
4 Setting focus SENSITIVITY  
then press the SET button.  
Use the cursor button (j or l) to move the cursor to  
SENSITIVITY, then use the cursor button (d or c) to  
change the setting. (e.g. LOW)  
The LENS screen will appear.  
2 Use the cursor button (d or c) to select AUTO, then  
Available settings:  
press the SET button.  
HIGH: High sensitivity focusing  
LOW: Low sensitivity focusing  
The FOCUS SETTING screen will appear.  
3 LIMIT NEAR focus distance setting  
Note: When focus SENSITIVITY is set to HIGH, it may react to  
even slight movements of the target object. In this case,  
change the setting to LOW.  
Use the cursor button (j or l) to move the cursor to  
LIMIT NEAR, then use the cursor button (d or c) to  
change the distance value. (e.g. 3M)  
Available settings: 1M (meter), 3M, 10C (centimeters), 30C,  
50C  
Note: Focusing becomes difficult when near distance limit is set  
to less than “1M”.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
5
FOCUS SETTING  
AREA SETTING  
6
AREA SETTING  
LIMIT NEAR  
3M  
LOW  
SET  
AREA  
2
AREA  
3
SENSITIVITY  
AREA  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
5 Use the cursor button (j or l) to move the cursor to  
6 Use the cursor button (d or c) to select the focus target  
SET for AREA, and press the SET button.  
area. (e.g. 3)  
The AREA SETTING screen for AREA 2 (default setting) will  
appear to allow setting of focus target area.  
The focus target area will become narrow.  
Available settings: 1/full screen, 2/center of screen,  
3/smaller center  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
B ZOOM setting  
Sets zooming speed and magnification power of the electronic zoom. This item also has a setting for improvement of vertical resolution  
sensitivity of still pictures.  
3
ZOOM SETTING  
4
4
ZOOM SETTING  
SPEED 4  
1
MAIN MENU  
2
LENS  
SPEED  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
FOCUS  
MANU ‚  
SET  
EL ZOOM  
OFF  
OFF  
EL ZOOM  
x4  
V-RESO.UP  
V-RESO.UP  
OFF  
ZOOM  
PRIVACY MASK  
LENS  
DAY/NIGHT  
AUTO ‚  
OFF  
MIRROR  
VIEW ANGLE  
VIEW SETTING  
OPTION  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
3 Zoom speed setting  
1 Use the cursor button (j or l) to select SET for LENS,  
then press the SET button.  
Use the cursor button (d or c) to select the zooming  
speed. (e.g. 4)  
The LENS screen will appear.  
Available settings: 1, 2, 3, 4 (Quickest speed)  
2 Use the cursor button (j or l) to select SET for ZOOM,  
then press the SET button.  
4 EL ZOOM (Electronic zoom) magnification setting  
The ZOOM SETTING screen will appear.  
Use the cursor button (j or l) to move the cursor to EL  
ZOOM, then use the cursor button (d or c) to select the  
electronic zoom magnification power. (e.g. x4)  
Available settings: OFF, x2, x4, x8, x16 (16 power)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
5
ZOOM SETTING  
SPEED  
4
x4  
EL ZOOM  
V-RESO.UP  
ON  
PRESET  
MENU  
OFF  
BACK  
5 V-RESO.UP (Vertical resolution sensitivity) setting  
Use the cursor button (j or l) to move the cursor to  
V-RESO.UP, then use the cursor button (d or c) to  
select the vertical resolution sensitivity. (e.g. ON)  
Note: When V-RESO.UP is set to “ON”, vertical resolution  
sensitivity for still pictures in the electronic zoom field will  
be improved but afterimages of moving objects will be  
more conspicuous.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
Note:  
V-RESO. UP will be automatically set to OFF when any of the  
following settings is made.  
IRIS SETTING: SENSE UP (x2...)(See p40)  
VIEW SETTING: SHUTTER (LONG)(See p47)  
D/N SETTING: DNR (ON)(See p25)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
C DAY/NIGHT setting  
The DAY/NIGHT mode can be set to one of three settings (AUTO, COLOR or B/W) to improve the appearance of images. This lets you set  
the filming mode to color mode during times of normal brightness, or to black & white mode to increase sensitivity when there is less light.  
When you select a mode, you may then need to make detailed settings for the respective mode used.  
LENS  
FOCUS  
MANU ‚  
SET  
ZOOM  
DAY/NIGHT  
VIEW ANGLE  
AUTO ‚  
OFF  
AUTO,  
COLOR,  
B/W  
PRESET  
MENU  
OFF  
BACK  
(Fig. 1)  
AUTO: Automatic mode; The mode switches automatically  
between color mode and black & white mode depending on  
the luminance of the objects being monitored. (See p24)  
Note:  
A sound may be heard when the colour image or black and  
white image is switched. Also, the image will be distorted as  
shown in Fig. 1. This is normal and does not indicate a  
problem.  
COLOR: Color mode; Images are filmed in color regardless of  
the luminance of the objects being monitored. (See p27)  
B/W: Black & white mode; Images are filmed in black & white  
regardless of the luminance of the objects being monitored.  
(See p28)  
When using infrared lighting, if there is a strong reflection on  
the subject, the optical filter may switch from black and white  
to colour mode. Use only enough infrared lighting so that the  
mode is not switched.  
Note: When “COLOR” is selected, the mode is fixed at color and  
you can only view images that are in color. The same  
applies to B/W mode. However, you can also use the  
ALARM IN terminal on the rear panel to force the mode to  
change from COLOR to B/W or from B/W to COLOR. Refer  
to the “Color/black & white selection setting” for  
details on the setting method. (See p59)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
AUTO mode setting  
Note:  
If the backlight compensation has been set to “MULTI”, the backlight compensation will be canceled when the mode is switched to  
B/W.  
If “SENSE UP” has been activated, SENSE UP mode will be activated after the mode switches to B/W mode.  
1
MAIN MENU  
2
D/N SETTING - AUTO  
LENS  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
AGC MAX GAIN  
DNR  
+9·  
OFF  
OFF  
1
FOCUS  
MANU ‚  
SET  
1
2
BURST  
ZOOM  
3
PRIVACY MASK  
LENS  
FOCUS  
LEVEL  
4
MID  
DAY/NIGHT  
AUTO ‚  
OFF  
5
MIRROR  
VIEW SETTING  
OPTION  
VIEW ANGLE  
PRESET  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
3 Sets burst suppression. If other peripheral devices (such  
as a multiplexer) are connected to the system, bursts  
(distortion of image color) can occur when switching  
between color and black & white. If this happens,  
change the BURST setting to “ON”.  
1 Use the cursor button (j or l) to select SET for LENS,  
then press the SET button.  
The LENS screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
DAY/NIGHT, use the cursor button (d or c) to select  
the mode (e.g. AUTO), and then press the SET button.  
4 Sets the focus when switching to black & white mode.  
5 Sets the switching level for color mode and black & white  
mode. The three available settings are LOW, MID or HIGH.  
In addition, the switching level can be set manually (ADJ).  
The D/N SETTING - AUTO screen will appear, and the “+9dB”  
setting for “AGC MAX GAIN” will be blinking.  
1 Sets the maximum AGC gain.  
2 Sets the digital noise reduction.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
3
D/N SETTING - AUTO  
4
D/N SETTING - AUTO  
5
D/N SETTING - AUTO  
6
D/N SETTING - AUTO  
AGC MAX GAIN  
DNR  
+9·  
OFF  
OFF  
1
AGC MAX GAIN  
DNR  
+9·  
ON  
OFF  
1
AGC MAX GAIN  
DNR  
+9·  
ON  
AGC MAX GAIN  
DNR  
+9·  
ON  
BURST  
BURST  
BURST  
ON  
BURST  
ON  
FOCUS  
LEVEL  
FOCUS  
LEVEL  
FOCUS  
1
FOCUS  
1
MID  
MID  
LEVEL  
MID  
LEVEL  
MID  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
3 AGC MAX GAIN setting  
5 BURST setting  
Use the cursor button (j or l) to move the cursor to  
AGC MAX GAIN, and then use the cursor button (d or  
c) to select the gain.  
Use the cursor button (j or l) to move the cursor to  
BURST, and then use the cursor button (d or c) to  
select the burst setting (e.g. ON).  
Available settings:  
Available settings: Select the maximum AGC gain from  
ON: The color burst signal is turned on.  
OFF: This should normally be set to “OFF”.  
+9dB, +12dB or +15dB.  
4 DNR setting  
6 FOCUS setting  
Use the cursor button (j or l) to move the cursor to  
DNR, and then use the cursor button (d or c) to select  
the digital noise reduction setting (e.g. ON).  
Use the cursor button (j or l) to move the cursor to  
FOCUS, and then use the cursor button (d or c) to  
select the focus setting (e.g. 1).  
Available settings:  
Available settings:  
ON: DNR (digital noise reduction) is applied. This reduces  
interference at low luminance levels.  
1: Near-infrared wavelength correction is set.  
(around 900 nm)  
OFF: DNR is not applied.  
2: Visible light spectrum is set.  
Note: Digital noise reduction operates when the gain control  
increases. In addition, blurring and ghosting of images  
can occur when moving images are being monitored,  
and so the resolution is also reduced slightly.  
Note: This is set to “1” at the time of shipment from the  
factory. If the images are out of focus, change it to 2”.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
7
D/N SETTING - AUTO  
LEVEL SETTING  
(COLOR†B/W)  
8
LEVEL SETTING  
(COLOR†B/W)  
AGC MAX GAIN  
DNR  
+9·  
OFF  
OFF  
1
4
4
4
4
BURST  
FOCUS  
LEVEL  
(B/W†COLOR)  
(B/W†COLOR)  
ADJ  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
7 LEVEL setting  
8 Use the cursor button (j or l) to move the cursor to  
COLOR†B/W, and then use the cursor button (d or c)  
to select the value.  
Use the cursor button (j or l) to move the cursor to  
LEVEL, use the cursor button (d or c) to select the level  
setting (e.g. ADJ) and then press the SET button.  
Available settings: 1 – 7  
The LEVEL SETTING screen will appear.  
Available settings:  
Note:  
The larger the value, the darker the switching level.  
LOW: The mode switches when the luminance of the  
Changing the setting for one of the switching level settings  
(from color mode to black & white mode or from black &  
white mode to color mode) causes the other setting to  
change also.  
objects being monitored is comparatively dark.  
MID: The mode switches when the luminance of the  
objects being monitored is between the LOW and  
HIGH levels.  
Set the switching level from black & white mode to color  
mode in the same way.  
HIGH: The mode switches when the luminance of the  
objects being monitored is comparatively bright.  
ADJ: The switching level for color mode to black & white  
mode and for black & white mode to color mode  
respectively can be set manually.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
COLOR mode setting  
1
MAIN MENU  
2, 3  
D/N SETTING - COLOR  
LENS  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
AGC MAX GAIN  
DNR  
0·  
OFF  
FOCUS  
MANU ‚  
SET  
1
2
ZOOM  
PRIVACY MASK  
LENS  
DAY/NIGHT  
COLOR‚  
OFF  
MIRROR  
VIEW SETTING  
OPTION  
VIEW ANGLE  
PRESET  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (j or l) to select SET for LENS,  
3 AGC MAX GAIN setting  
then press the SET button.  
Use the cursor button (j or l) to move the cursor to  
AGC MAX GAIN, and then use the cursor button (d or  
c) to select the gain.  
The LENS screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
DAY/NIGHT, use the cursor button (d or c) to select  
the level setting (e.g. COLOR) and then press the SET  
button.  
Available settings: Select the maximum AGC gain from OFF,  
–6dB, 0dB, +6dB or +9dB.  
Setting fixed gain manually  
The D/N SETTING - COLOR screen will appear, and the “ 0dB”  
setting for “AGC MAX GAIN” will be blinking.  
1 Sets the maximum AGC gain.  
Set AGC MAX GAIN to “OFF” and then press the SET  
button.  
The GAIN SETTING screen will appear. You can use this screen  
to set the gain value manually to within a range of 0 – 30 dB.  
2 Sets the digital noise reduction.  
Note:  
If “OFF” is selected, no maximum gain will be set.  
If “OFF” is selected, the SENSE UP function will be forcibly set  
to “OFF”. However, the setting display will not change.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
B/W mode setting  
4
D/N SETTING - COLOR  
AGC MAX GAIN  
DNR  
0·  
OFF  
1
MAIN MENU  
LENS  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
FOCUS  
MANU ‚  
ZOOM  
SET  
B/W  
OFF  
DAY/NIGHT  
PRESET  
MENU  
OFF  
BACK  
MIRROR  
VIEW SETTING  
OPTION  
VIEW ANGLE  
PRESET  
MENU  
PRESET  
MENU  
OFF  
BACK  
4 DNR setting  
Use the cursor button (j or l) to move the cursor to  
DNR, and then use the cursor button (d or c) to select  
the digital noise reduction setting (e.g. ON).  
1 Use the cursor button (j or l) to select SET for LENS,  
then press the SET button.  
The LENS screen will appear.  
Available settings:  
ON: DNR (digital noise reduction) is applied. This reduces  
interference at low luminance levels.  
OFF: DNR is not applied.  
Note:  
Digital noise reduction operates when the gain control  
increases. In addition, blurring and ghosting of images can  
occur when moving images are being monitored, and so the  
resolution is also reduced slightly.  
If AGC MAX GAIN is set to “OFF”, DNR will be forcibly set to  
OFF”.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
2
D/N SETTING - B/W  
3
D/N SETTING - B/W  
AGC MAX GAIN  
DNR  
+6·  
AGC MAX GAIN  
DNR  
+6·  
1
OFF  
OFF  
1
OFF  
OFF  
1
2
BURST  
BURST  
3
4
FOCUS  
FOCUS  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
2 Use the cursor button (j or l) to move the cursor to  
DAY/NIGHT, use the cursor button (d or c) to select  
the level setting (e.g. B/W) and then press the SET  
button.  
3 AGC MAX GAIN setting  
Use the cursor button (j or l) to move the cursor to  
AGC MAX GAIN, and then use the cursor button (d or  
c) to select the gain.  
The D/N SETTING – B/W screen will appear, and the “+6dB”  
setting for “AGC MAX GAIN” will be blinking.  
1 Sets the maximum AGC gain.  
Available settings: Select the maximum AGC gain from OFF,  
–6dB, 0dB, +6dB, +9dB, +12dB or  
+15dB.  
2 Sets the digital noise reduction.  
Setting fixed gain manually  
3 Sets burst suppression. If other peripheral devices (such  
as a multiplexer) are connected to the system, bursts  
(distortion of image color) can occur when switching  
between color and black & white. If this happens,  
change the BURST setting to “ON”.  
Set AGC MAX GAIN to “OFF” and then press the SET  
button.  
The GAIN SETTING screen will appear. You can use this screen  
to set the gain value manually to within a range of 0 – 30 dB.  
Note:  
4 Sets the focus when switching to black & white mode.  
If “OFF” is selected, no maximum gain will be set.  
If “OFF” is selected, the SENSE UP function will be forcibly set  
to “OFF”. However, the setting display will not change.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
4
D/N SETTING - B/W  
5, 6  
D/N SETTING - B/W  
5 BURST setting  
AGC MAX GAIN  
DNR  
+6·  
AGC MAX GAIN  
DNR  
+6·  
Use the cursor button (j or l) to move the cursor to  
BURST, and then use the cursor button (d or c) to  
select the burst setting (e.g. ON).  
ON  
OFF  
1
ON  
ON  
1
BURST  
BURST  
FOCUS  
FOCUS  
Available settings:  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
ON: The color burst signal is turned on.  
OFF: This should normally be set to “OFF”.  
4 DNR setting  
6 FOCUS setting  
Use the cursor button (j or l) to move the cursor to  
DNR, and then use the cursor button (d or c) to select  
the digital noise reduction setting (e.g. ON).  
Use the cursor button (j or l) to move the cursor to  
FOCUS, and then use the cursor button (d or c) to  
select the focus setting (e.g. 1).  
Available settings:  
Available settings:  
ON: DNR (digital noise reduction) is applied. This reduces  
1: Near-infrared wavelength correction is set.  
interference at low luminance levels.  
(around 900 nm)  
OFF: DNR is not applied.  
2: Visible light spectrum is set.  
Note:  
Note: This is set to “1” at the time of shipment from the factory.  
Digital noise reduction operates when the gain control  
increases. In addition, blurring and ghosting of images can  
occur when moving images are being monitored, and so the  
resolution is also reduced slightly.  
If the images are out of focus, change it to “2”.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
If AGC MAX GAIN is set to “OFF”, DNR will be forcibly set to  
OFF”.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LENS SETTING (LENS)  
D VIEW ANGLE setting  
Day/Night mode operation from the system controller  
The VIEW ANGLE setting should normally be left at “OFF”.  
The Day/Night setting (AUTO, COLOR and B/W) can be  
switched using “CAMERA” operating range of the system  
controller. Press the following buttons in the order given to  
change the mode setting.  
1
MAIN MENU  
2
LENS  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
FOCUS  
MANU ‚  
SET  
ZOOM  
COLOR mode:  
AUXAUX1Enter+” button  
B/W mode:  
DAY/NIGHT  
AUTO ‚  
OFF  
MIRROR  
VIEW SETTING  
OPTION  
VIEW ANGLE  
PRESET  
MENU  
PRESET  
MENU  
OFF  
BACK  
AUXAUX2Enter+” button  
AUTO mode:  
AUXAUX3Enter+” button  
1 Use the cursor button (j or l) to select SET for LENS,  
then press the SET button.  
The LENS screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
VIEW ANGLE, and then use the cursor button (d or c)  
to select the setting (e.g. OFF).  
Available settings:  
OVER: The image angle for images being monitored is set  
to 1.05.  
OFF: This should normally be set to “OFF”.  
Note: This should normally be set to “OFF”. However, vignetting  
may occur in the corners of the images because of the  
zoom position. This is not normally a problem, but if you  
are concerned about it, change the setting to “OVER”. The  
vignetting will then be less apparent.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MIRROR SETTING  
1
MAIN MENU  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
PRIVACY MASK  
LENS  
MIRROR  
VIEW SETTING  
OPTION  
PRESET  
MENU  
1 Use the cursor button (j or l) to move the cursor to  
MIRROR, then use the cursor button (d or c) to select  
the mirror image effect (e.g. H).  
The image will change as described below each time the  
cursor button is pressed.  
OFF: Normal image  
V: Inverted vertically  
H: Inverted horizontally HV: Inverted horizontally and  
vertically  
OFF  
H
V
HV  
2 To return to the normal screen, use the cursor button  
(l) to select END at the bottom of the screen, then press  
the SET button.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING ITEM FLOW  
A IRIS setting (See p35)  
MAIN MENU  
This setting allows selection of IRIS to either autoiris (AUTO) or manual iris (MANU). Default setting is  
autoiris.  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
PRIVACY MASK  
LENS  
B WHITE BALANCE adjustment (See p42)  
MIRROR  
Three white balance methods are available: auto trace white balance (ATW), one-push automatic  
white balance (AWC), and manual white balance (MWB). Default setting is auto trace white balance.  
VIEW SETTING  
OPTION  
PRESET  
MENU  
C Electronic SHUTTER setting (See p46)  
This setting chooses either a fast shutter speed (SHORT) for target objects that may be moving quickly  
or a slower shutter speed (LONG) for darker target objects.  
A
B
C
D
E
VIEW SETTING 1  
IRIS  
AUTO ‚  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
OFF  
OFF  
ON  
D MOTION detector setting (See p48)  
APERTURE  
GAMMA  
This function generates an alarm when a suspicious figure is detected. Each of the settings will enable  
certain kinds of detection based on the natural image (swaying trees, flickers of light, etc.). It is also  
possible to enable zooming in on target objects and intruders that have unusual brightness levels  
(moving, bright) or are fast-moving.  
ON  
PRESET  
MENU  
OFF  
BACK  
F
E Profile compensation setting (APERTURE) (See p54)  
This setting emphasizes the target object profile (horizontally or vertically).  
Setting the VIEW SETTING  
Signifies that VIEW  
F GAMMA correction setting (See p55)  
This setting enables contrast sensitivity to be boosted by controlling the gamma characteristics. Three  
gamma controls are available: gamma correction (ON), smart gamma correction 1 (SMART 1), and  
smart gamma correction 2 (SMART 2). Default setting is ON.  
SETTING 1 is the camera  
setting 1. The cursor  
button can be used (d or  
c) to select one of the  
nine VIEW SETTING  
patterns (0 – 8).  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING ITEM FLOW  
(About creating image setting files in VIEW SETTING)  
Note: When each of the following functions is ON (shown by  
single circle), it may be possible to use other functions in  
conjunction with it (shown by double circle). View columns  
vertically to determine which functions can be used  
together.  
You can set 9 different patterns with view files. Use the cursor  
button (d or c) to change the file number (1) for VIEW SETTING  
and press the SET button. The selected image setting file will  
appear. Neither the mask function nor the motion detector  
function can be used with image setting file “0”, so they will not  
appear as options in the screen for pattern 0.  
IRIS  
AUTO: SENSE UP (activated)  
MANU: EI (ON)  
F
T
T
T
T
T
F
T
T
E
T
T
F
T
T
T
T
T
F
E
T
E
T
MAIN MENU  
VIEW SETTING 1  
IRIS AUTO ‚  
SHUTTER LONG  
SHORT  
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
WHITE BALANCE  
SHUTTER  
ATW  
OFF  
OFF  
ON  
E
F
MOTION  
APERTURE  
GAMMA  
MOTION  
MIRROR  
ON  
VIEW SETTING  
OPTION  
F: Function is set T: Not allowable E: Allowable  
PRESET  
MENU  
PRESET  
MENU  
OFF  
BACK  
(Screen for image setting 1 – 8)  
VIEW SETTING 0  
IRIS  
AUTO ‚  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
OFF  
---  
ON  
APERTURE  
GAMMA  
ON  
PRESET  
MENU  
OFF  
BACK  
(Screen for image setting 0)  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
A IRIS setting  
There are 2 possible settings for IRIS, autoiris (AUTO) and manual iris (MANU).  
Autoiris setting (AUTO)  
Sets backlight compensation, magnification of electronic  
sensitivity and iris level.  
VIEW SETTING 1  
1
IRIS  
AUTO ‚  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
OFF  
OFF  
ON  
APERTURE  
GAMMA  
ON  
PRESET  
MENU  
OFF  
BACK  
1 Use the cursor button (j or l) to move the cursor to  
2 Press the SET button.  
VIEW SETTING, then press the SET button. (e.g. 1)  
The IRIS SETTING screen will appear.  
The VIEW SETTING 1 screen will appear and AUTO for IRIS will  
be blinking.  
Available settings:  
AUTO: Sets automatic adjustment of iris.  
MANU: Sets manual adjustment of iris.  
Note:  
When AUTO is selected, the following 3 types of detailed  
backlight compensation settings will be available.  
Multi-spot evaluative metering (MULT)  
5 spot centerweighted average metering (CENT)  
48 multi-spot metering (MASK)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Backlight compensation additional settings 1  
IRIS SETTING  
BLC SETTING  
1
2
3 Use the cursor button (j or l) to move the cursor to  
BRIGHT, and then use the cursor button (d or c) to  
select the compensation level.  
BLC  
SENSE UP  
MULT ‚  
OFF  
(BLC WEIGHT)  
í------ú------ü  
7
7
(LEVEL)  
í-----ú+------ü 40  
(BRIGHT)  
í------ú------ü  
Available settings: 0 – 15  
Note: When the number becomes larger, it brightens, and the  
compensation level can be set for the brightness of the  
backlighting.  
Backlight compensation settings  
MULT (Multi-spot evaluative metering): Evaluates the entire  
screen and corrects according to the best image obtained.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
CENT (5 spot centerweighted average metering): Measures  
light mainly at the center and corrects according to the best  
image obtained. (See p37)  
MASK (48 multi-spot metering): Covers bright areas such as  
persons with mask patterns and treats light measurement  
output as irrelevant. (See p39)  
Note:  
When using multi-spot evaluative metering, the background  
behind the target object will become very dark. If a target  
image in the center of the image is too bright while using the  
multi-spot evaluative metering mode, switch to the 5 spot  
centerweighted average metering mode.  
Multi-spot evaluative metering (MULT)  
1 Use the cursor button (j or l) to move the cursor to  
BLC, then use the cursor button (d or c) to select a  
backlight compensation method. (e.g. MULT) Then press  
the SET button.  
If DAY/NIGHT is set to “AUTO” and the images are in black &  
white mode, multi-spot evaluative metering will not operate.  
The BLC SETTING screen will appear.  
2 Use the cursor button (d or c) to select the value of  
BLC WEIGHT. (Sets backlight and brightness level.)  
Available settings: 0 – 15  
Note: The larger the number, the more backlighting works.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Backlight compensation additional settings 2  
5 spot centerweighted average metering (CENT)  
IRIS SETTING  
BLC SETTING  
(POSITION)  
BLC SETTING  
(SIZE)  
1
2
4
BLC  
SENSE UP  
CENT ‚  
OFF  
(LEVEL)  
í-----ú+------ü 40  
PRESET  
MENU  
OFF  
BACK  
1 Use the cursor button (d or c) to select CENT, then  
4 Use the cursor button (j l d c) to adjust the size of  
press the SET button.  
the central light sensing zone.  
The BLC SETTING (POSITION) screen will appear.  
5 Press the SET button.  
2 Use the cursor button (j l d c) to shift the position  
The BLC WINDOW WEIGHTING screen will appear.  
of the central light sensing zone.  
The zone can be moved up or down and left or right.  
Note:  
If the zone fills the right side it will become smaller.  
If the zone fills the bottom side it will become smaller.  
3 Press the SET button.  
The BLC SETTING (SIZE) screen will appear.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Example of setting the mask in the center weighting position.  
1
2
3
4
6
BLC WINDOW WEIGHTING  
BLC WINDOW WEIGHTING  
BLC WINDOW WEIGHTING  
BLC WINDOW WEIGHTING  
TOP  
0
0
0
0
7
TOP  
0
0
0
0
7
TOP  
0
0
0
0
7
TOP  
0
0
0
0
7
BOTTOM  
LEFT  
BOTTOM  
LEFT  
BOTTOM  
LEFT  
BOTTOM  
LEFT  
RIGHT  
CENTER(FIX)  
RIGHT  
CENTER(FIX)  
RIGHT  
CENTER(FIX)  
RIGHT  
CENTER(FIX)  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
1 TOP: Weighting is at top.  
2 BOTTOM: Weighting is at bottom.  
3 LEFT: Weighting is at left.  
4 RIGHT: Weighting is at right.  
5
BLC WINDOW WEIGHTING  
TOP  
0
0
0
0
7
BOTTOM  
LEFT  
5 CENT (FIX): Center weighting is fixed by the number 7.  
RIGHT  
CENTER(FIX)  
If this is set to “0”, the light intensity will be ignored. The larger the setting value, the  
greater is the weighting given to light coming from the respective side.  
Note:  
PRESET  
MENU  
OFF  
BACK  
6 Use the cursor button (j or l) to select a zone, then  
use the cursor button (d or c) to adjust weighting.  
Each setting will change as shown in the illustration.  
The area from each of the zones 0 – 7, except CENTER, can  
be adjusted.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Backlight compensation additional settings 3  
48 multi-spot metering (MASK)  
IRIS SETTING  
BLC MASKING  
BLC MASKING  
1
2
BLC  
SENSE UP  
MASK ‚  
OFF  
(LEVEL)  
í-----ú+------ü 40  
CONTINUE (ñ)  
CONTINUE (ñ)  
PRESET  
MENU  
OFF  
BACK  
1 Use the cursor button (d or c) to select MASK, then  
3 Finishing mask pattern setting  
press the SET button.  
Use the cursor button (j or l) to move a mask pattern to  
the bottom area of the screen and continue holding it for 3  
seconds. The PRESET and MENU items will appear on the  
screen.  
The BLC MASKING screen will appear and the mask pattern  
will be blinking.  
2 Use the cursor button (j l d c) to move the cursor to  
move the mask pattern over the area not to be sensed,  
then press the SET button.  
Use the cursor button (l) to select BACK for MENU and  
press the SET button. The IRIS SETTING screen will  
reappear.  
The mask pattern will be set. You can use the same steps to  
set additional mask patterns.  
Use the cursor button (l) to move the cursor to BACK for  
MENU, use the cursor button (d or c) to select END, and  
then press the SET button. The normal screen will reappear.  
Note: The initial mask pattern is at the upper left of the screen,  
and it is not set. To clear a mask pattern after it is set,  
press the SET button again.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
SENSE UP setting  
LEVEL setting  
IRIS SETTING  
MULT  
IRIS SETTING  
BLC  
SENSE UP  
MULT  
x4  
BLC  
SENSE UP  
x4  
(LEVEL)  
í----ú-+------ü 40  
(LEVEL)  
í-----ú+------ü 40  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
Use the cursor button (j or l) to move the cursor to  
LEVEL, then use the cursor button (d or c) to adjust the iris  
level.  
Use the cursor button (j or l) to move the cursor to  
SENSE UP, then use the cursor button (d or c) to select the  
power of the electronic sensitivity. (e.g. x4)  
Available settings: 0 – 100  
Available settings: OFF, x2, x4, x8, x16, x32  
Note: The larger the number, the more it brightens.  
Note:  
Electronic sensitivity boosting (SENSE UP) automatically  
lengthens the CCD exposure time in dark situations.  
Accordingly, do not use for light target objects. Because  
exposure time is lengthened while in operation, moving target  
objects may cause conspicuous afterimages and blurs.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
It is not possible to set SENSE UP (activated) or SHUTTER  
(LONG) when MOTION is set to “ON”.  
When SENSE UP is activated for IRIS SETTING, the electronic  
shutter cannot be forcibly moved.  
If DAY/NIGHT is set to “AUTO” and the images are in color  
mode, electronic sensitivity boosting will not operate.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Manual iris setting  
Sets electronic iris ON/OFF, lens aperture and iris level.  
MAIN MENU  
VIEW SETTING 1  
IRIS SETTING  
ON  
IRIS SETTING  
ON  
1
2
3
5
LANGUAGE  
CAMERA ID  
SYNC  
PRIVACY MASK  
LENS  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
IRIS  
MANU ‚  
EI  
EI  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
LONG ‚  
OFF  
(IRIS STOP)  
í------+------ú 17  
(IRIS STOP)  
í------+------ú 17  
APERTURE  
GAMMA  
ON  
ON  
MIRROR  
(LEVEL)  
í----ú-+------ü 40  
(LEVEL)  
í----ú-+------ü 40  
VIEW SETTING  
OPTION  
SET  
1 Use the cursor button (j or l) to move the cursor to  
5 Use the cursor button (j or l) to move the cursor to  
LEVEL, then use the cursor button (d or c) to select the  
value.  
VIEW SETTING, then press the SET button. (e.g. 1)  
The VIEW SETTING 1 screen will appear.  
Available settings: 0 – 100 (Level of opening)  
2 Use the cursor button (d or c) to select MANU, then  
press the SET button.  
Note:  
The IRIS SETTING screen will appear.  
The smaller the value the more the video level drops,  
becoming darker.  
3 Electronic IRIS setting  
The LEVEL setting controls both AGC circuit gain and shutter  
speed, changing the amount of exposure.  
Use the cursor button (d or c) to select El. (e.g. ON)  
Note: When SENSE UP is activated for IRIS SETTING, the  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
electronic shutter cannot be forcibly moved.  
4 Lens aperture setting  
Use the cursor button (j or l) to move the cursor to IRIS  
Note:  
STOP, then use the cursor button (d or c) to select the value.  
If the iris views an unusually bright image, it can cause a  
smear that cannot be corrected by adjusting the light entering  
through the lens. In this case, arrange the physical angle of  
lighting in a way that will prevent on-screen smearing.  
Available settings: 1 – 17 (Aperture opening)  
Note:  
The smaller the value the more the aperture closes and the  
image darkens.  
If flickering of the target object occurs because of florescent  
lighting in the camera location, changing to incandescent  
lighting will prevent the flickering.  
Changes to the value directly control the aperture of the lens.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
B WHITE BALANCE adjustment  
Adjustments can be made to 3 methods of white balance correction: Auto trace white balance (ATW), one-push automatic white balance  
(AWC), and manual white balance (MWB).  
MAIN MENU  
VIEW SETTING 1  
IRIS AUTO ‚  
1
2
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
WHITE BALANCE  
SHUTTER  
MWB  
OFF  
OFF  
ON  
PRIVACY MASK  
LENS  
MOTION  
APERTURE  
GAMMA  
MIRROR  
ON  
VIEW SETTING  
OPTION  
PRESET  
PRESET  
MENU  
OFF  
BACK  
MENU  
The following methods are available for white balance correction.  
See the corresponding reference sections for additional setting  
options.  
1 Use the cursor button (j or l) to move the cursor to  
VIEW SETTING, then press the SET button. (e.g. 1)  
The VIEW SETTING 1 screen will appear.  
Available methods:  
2 Use the cursor button (j or l) to move the cursor to  
WHITE BALANCE, then use the cursor button (d or c)  
to select a white balance type “MWB”. Then press the  
SET button.  
ATW (Auto trace white balance)  
Even when light sources change, automatic adjustment assures  
capture of most suitable colors. When a bright light source  
prevents effective white balance, a mask can be placed over the  
light source. (See p43)  
The MWB SETTING screen will appear.  
AWC (One-push automatic white balance)  
White balance is adjusted automatically with one-push activation.  
AWC is usually set for white target objects (walls, paper, etc.) that  
do not return color faithfully in the ATW method. (See p45)  
MWB (Manual white balance)  
Fine adjustments for preferred colors can be done manually. This  
method is preferable when suitable colors cannot be obtained  
with the ATW method. (See p43)  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
White balance additional settings 1  
MWB setting  
White balance additional settings 2  
ATW setting  
Automatic white balance settings are completed when ATW is  
selected. However, white balance will not be suitably adjusted if a  
bright light source or an excessively dark area from the  
environment is in the image. In this case, the bright light source or  
dark area should be masked so that it will not be detected.  
VIEW SETTING 1  
MWB SETTING  
(OFFSET)  
1
2
IRIS  
AUTO ‚  
WHITE BALANCE  
SHUTTER  
MOTION  
MWB  
LONG ‚  
OFF  
R í---ú--+------ü 70  
B í---ú--+------ü 66  
APERTURE  
GAMMA  
ON  
ON  
VIEW SETTING 1  
AUTO ‚  
ATW SETTING  
1
2
1 Use the cursor button (j or l) to move the cursor to  
WHITE BALANCE, then use the cursor button (d or c)  
to select a white balance type (e.g. MWB). Then press  
the SET button.  
IRIS  
MASKING  
SMART ATW  
ON  
WHITE BALANCE  
SHUTTER  
ATW  
OFF  
OFF  
ON  
OFF  
MOTION  
APERTURE  
GAMMA  
ON  
The MWB SETTING screen will appear.  
1 Use the cursor button (j or l) to move the cursor to  
2 Use the cursor button (d or c) to adjust the value for  
ATW for WHITE BALANCE and press the SET button.  
“R” (red).  
The ATW SETTING screen will appear.  
Available settings: 0 – 255  
2 Use the cursor button (d or c) to select ON for  
Note: The larger the number, the stronger red becomes.  
MASKING, then press the SET button.  
3 Use the cursor button (j or l) to move the cursor to  
“B”, then use the cursor button (d or c) to adjust the  
“Blue” value.  
The ATW MASKING screen will appear with the mask pattern  
blinking in the upper left corner of the screen.  
Available settings: 0 – 255  
Note: The larger the number, the stronger blue becomes.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
ATW MASKING  
ATW MASKING  
ATW SETTING  
ATW SETTING  
3
4
5
MASKING  
ON  
MASKING  
ON  
ON  
SMART ATW  
OFF  
SMART ATW  
CONTINUE (ñ)  
CONTINUE (ñ)  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
SMART ATW setting  
If saturation is high or a scene is bright, the most suitable colors  
may not be obtained. In this case, set the SMART ATW to ON.  
3 Use the cursor button (j l d c) to move the mask  
pattern over the bright light source, then press the SET  
button.  
Use the same steps to place addition masks as needed.  
5 Use the cursor button (j or l) to move the cursor to  
SMART ATW, then use the cursor button (d or c) to set  
ON.  
Note: Initial settings place no masks on the screen. To cancel the  
placement of masks, press the SET button again.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
4 Use the cursor button (j or l) to move a mask pattern  
to the bottom area of the screen and continue holding  
the cursor button straight down for 3 seconds.  
The PRESET and MENU items will appear on the screen. Use  
the cursor button (j or l) to select BACK, then press the  
SET button. The ATW SETTING screen will reappear.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
White balance additional settings 3  
AWC setting  
VIEW SETTING 1  
AWC SETTING  
AWC SETTING  
MWB SETTING  
(OFFSET)  
1
2
3
4
IRIS  
AUTO ‚  
AWC LOCK  
GO TO MWB  
SET  
SET  
AWC LOCK  
GO TO MWB  
SET  
SET  
WHITE BALANCE  
SHUTTER  
MOTION  
AWC  
OFF  
OFF  
ON  
R í---ú--+------ü 70  
B í---ú--+------ü 66  
APERTURE  
GAMMA  
ON  
1 Use the cursor button (j or l) to move the cursor to  
3 GO TO MWB setting  
AWC for WHITE BALANCE and press the SET button.  
Use the cursor button (j or l) to move the cursor to  
The AWC SETTING screen will appear.  
SET for GO TO MWB and press the SET button.  
The MWB SETTING screen will appear and the “R” value will  
be blinking.  
2 With SET blinking for AWC LOCK, press the SET button.  
SET will light and adjustment of white balance will begin. After  
about 3 seconds, SET will begin blinking again, signaling that  
adjustment is complete.  
4 Use the cursor button (d or c) to adjust the value for  
“R” (red).  
Available settings: 0 – 255  
Note:  
Note: The larger the number, the stronger red becomes.  
For even finer adjustment of coloration, choose SET for GO TO  
MWB. White balance mode will become MWB for fine  
adjustment. After fine adjustment with GO TO MWB, the white  
balance mode will automatically switch to MWB.  
5 Use the cursor button (j or l) to move the cursor to  
“B”, then use the cursor button (d or c) to adjust the  
“Blue” value.  
Note: Full adjustment may not be possible with just one  
activation of SET for AWC LOCK. In that case, press the  
SET button again.  
Available settings: 0 – 255  
Note: The larger the number, the stronger blue becomes.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
C Electronic SHUTTER setting  
Sets the electronic shutter to either the fast shutter speed mode (SHORT) or the slow shutter speed mode (LONG).  
Fast shutter speed (SHORT) mode setting  
MAIN MENU  
VIEW SETTING 1  
MANU ‚  
ES SETTING  
1
2
3
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
IRIS  
SHUTTER SPEED  
60  
WHITE BALANCE  
SHUTTER  
ATW  
SHORT‚  
OFF  
PRIVACY MASK  
LENS  
MOTION  
APERTURE  
GAMMA  
ON  
MIRROR  
OFF  
VIEW SETTING  
OPTION  
PRESET  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (j or l) to move the cursor to  
3 Use the cursor button (d or c) to select a electronic  
VIEW SETTING, then press the SET button. (e.g. 1)  
shutter speed.  
The VIEW SETTING 1 screen will appear.  
Available settings: 60, 100, 250, 500, 1000, 2000, 4000,  
10000  
2 Use the cursor button (j or l) to move the cursor to  
SHUTTER, then use the cursor button (d or c) to select  
the speed mode for the electronic shutter. (e.g. SHORT)  
Then press the SET button.  
Note: SHORT mode cannot be set if SENSE UP is activated or IRIS  
is “ON”.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
The ES SETTING screen will appear and 60 (1/60 sec) will be  
blinking. This setting is suitable for fast moving target objects.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
Slow shutter speed (LONG) mode setting  
VIEW SETTING 1  
ES SETTING  
1
2
IRIS  
MANU ‚  
SHUTTER SPEED  
x1  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
LONG ‚  
OFF  
APERTURE  
GAMMA  
ON  
ON  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
Note:  
1 Use the cursor button (j or l) to move the cursor to  
SHUTTER, then use the cursor button (d or c) to select  
the speed mode for the electronic shutter. (e.g. LONG)  
Then press the SET button.  
SHUTTER (LONG) cannot be set if any of the following settings is  
active.  
MOTION: ON  
The ES SETTING screen will appear and x1 (1/60 sec) will be  
blinking. This setting is suitable for dark target objects.  
IRIS: AUTO item SENSE UP (activated) or MANU item El  
(ON)  
Note: When setting the electronic shutter, the ELS button on the  
system controller can only be used to turn the electronic  
shutter on and off.  
2 Use the cursor button (d or c) to select a electronic  
shutter speed.  
Available settings: x1, x2, x4, x8, x16, x32 (Field times  
shown as multiples.)  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
D MOTION detector setting  
This function divides the monitor screen into 48 zones (8 x 6). Based on information from the separate zones, target images tha t show  
intruder movements are detected and an alarm is generated. The degree of motion to be detected can be finely set.  
Note:  
Before activating this setting, use the cursor button to select a surveillance location that will not detect motion.  
When SHUTTER speed is in LONG mode and IRIS SETTING has SENSE UP activated, the MOTION function cannot be turned ON.  
MAIN MENU  
VIEW SETTING 1  
MANU ‚  
MOTION SETTING  
MOTION SIZE  
1
2
3
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
IRIS  
SIZE  
SET  
WHITE BALANCE  
SHUTTER  
ATW  
MASKING  
SENSITIVITY  
ZOOM  
ON  
V
H
1
1
LONG ‚  
SET  
OFF  
5S  
PRIVACY MASK  
LENS  
MOTION  
APERTURE  
GAMMA  
ON  
ON  
ON  
INTERVAL  
ALARM SIGN  
MIRROR  
OFF  
VIEW SETTING  
OPTION  
PRESET  
MENU  
OFF  
BACK  
PRESET  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (j or l) to move the cursor to  
3 MOTION SIZE setting  
VIEW SETTING, then press the SET button. (e.g. 1)  
Sets the target object size desired for detection in the 48 zone  
screen.  
The VIEW SETTING 1 screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
MOTION, and then use the cursor button (d or c) to  
select ON. Then press the SET button.  
Press the SET button again.  
The MOTION SIZE screen appears and the “1” for “V” will be  
blinking.  
The MOTION SETTING screen will appear and SET for SIZE will  
be blinking.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
MOTION SIZE  
MOTION SIZE  
MOTION SIZE  
4 Set the size of the target object desired for detection  
1 Determine the vertical size  
V
H
1
1
V
H
2
1
V
H
6
1
Tilt the cursor button to the right (c).  
PRESET  
MENU  
OFF  
PRESET  
MENU  
OFF  
PRESET  
MENU  
OFF  
BACK  
BACK  
BACK  
The “V” value (vertical pattern) will change to “2” and the  
detection pattern will expand downward. Repeating this  
motion will expand the pattern in the up and down  
direction. Tilting the cursor button to the left will reduce  
the pattern size.  
V1, H1  
V2, H1  
V6, H1  
MOTION SIZE  
MOTION SIZE  
MOTION SIZE  
V
H
2
2
V
H
2
3
V
H
3
3
2 Determine the horizontal size  
PRESET  
MENU  
OFF  
PRESET  
MENU  
OFF  
PRESET  
MENU  
OFF  
Use the cursor button (l) to move the cursor to the  
“1” for “H”, then tilt the cursor button to the right  
(c).  
BACK  
BACK  
BACK  
V2, H2  
V2, H3  
V3, H3  
MOTION SIZE  
MOTION SIZE  
MOTION SIZE  
The “H” value (horizontal pattern) will change to “2” and the  
detection pattern will expand to the left. Repeating this  
motion will expand the pattern in the left and right direction.  
Tilting the cursor button to the left will reduce the pattern  
size.  
V
H
1
2
V
H
1
3
V
H
1
8
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
V1, H2  
V1, H3  
V1, H8  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
MOTION MASKING setting  
Masking target objects that are not desired for detection (swaying trees, flickers of light , etc.) will prevent unwanted alarms from being  
generated. This is done in the MOTION SETTING screen.  
MOTION SETTING  
MOTION MASKING  
MOTION MASKING  
1
2
SIZE  
SET  
MASKING  
SENSITIVITY  
ZOOM  
ON  
SET  
OFF  
5S  
INTERVAL  
ALARM SIGN  
OFF  
CONTINUE (ñ)  
CONTINUE (ñ)  
PRESET  
MENU  
OFF  
BACK  
1 Use the cursor button (j or l) to move the cursor to  
MASKING, and then use the cursor button (d or c) to  
select ON. Then press the SET button.  
3 Finishing motion pattern setting  
Use the cursor button (j or l) to move a mask pattern to  
the bottom area of the screen and continue holding it for 3  
seconds. The PRESET and MENU items will appear on the  
screen.  
The MOTION MASKING screen will appear, and the mask  
pattern will be blinking in the upper left corner of the screen.  
2 Use the cursor button (j l d c) to move the mask  
pattern to the target object that is not to be detected,  
then press the SET button.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
Repeat these steps to set mask patterns in other locations.  
Note: To clear a mask pattern, press the SET button again on  
the pattern.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
When noise from a dark screen is causing erroneous detections,  
make the value larger.  
SENSITIVITY setting  
Set the degree of sensitivity for motion detection corresponding  
to MOTION SIZE. Sensitivity can be set so that natural motions on  
the screen such as wind and light changes will not be detected.  
When this is necessary, activate the following setting.  
Available settings: 1 – 10  
Brightness differences (Y-DIFFER)  
Use the cursor button (j or l) to move the cursor to  
Y-DIFFER, then use the cursor button (d or c) to adjust the  
brightness differences.  
MOTION SETTING  
SENSITIVITY  
í---ú----ü  
Y-LEVEL í---ú----ü  
Y-DIFFER í---ú----ü  
DURATION ú--------ü  
SIZE  
SET  
MOVE  
5
5
5
1
MASKING  
SENSITIVITY  
ZOOM  
ON  
SET  
OFF  
5S  
Changes in brightness can sometimes be mistakenly detected as  
motion. To avoid detection of the turning on and off of lighting,  
make the value larger.  
INTERVAL  
ALARM SIGN  
OFF  
DEMO  
OFF  
Available settings: 1 – 10  
Use the cursor button (j or l) to move the cursor to  
SENSITIVITY, and then use the cursor button (d or c) to  
DURATION setting  
select SET. Then press the SET button.  
Use the cursor button (j or l) to move the cursor to  
DURATION, then use the cursor button (d or c) to adjust  
the detection time duration.  
The SENSITIVITY screen will appear.  
When necessary, adjust the following settings.  
To avoid detecting fast movements, make the value larger.  
Motion sensitivity (MOVE) setting  
Available settings: 1 – 60  
Use the cursor button (j or l) to move the cursor to  
MOVE, then use the cursor button (d or c) to adjust the  
movement value.  
Detected motion confirmation mode (DEMO)  
Use the cursor button (j or l) to move the cursor to OFF for  
DEMO, then use the cursor button (d or c) to change ON.  
To avoid detection of small movements such as wind, make the  
value larger.  
When a motion is detected, patterns are shown in that location.  
While the detected motion is being confirmed, the SENSITIVITY  
settings are optimized. This mode can only be activated in the  
SENSITIVITY setting screen.  
Available settings: 1 – 10  
Brightness level (Y-LEVEL)  
Use the cursor button (j or l) to move the cursor to  
Y-LEVEL, then use the cursor button (d or c) to adjust the  
brightness level.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
ZOOM setting  
INTERVAL setting  
This item is set in the MOTION SETTING screen.  
This item is set in the MOTION SETTING screen.  
MOTION SETTING  
MOTION SETTING  
SIZE  
SET  
ON  
SIZE  
SET  
ON  
MASKING  
SENSITIVITY  
ZOOM  
MASKING  
SENSITIVITY  
ZOOM  
SET  
OFF  
5S  
SET  
OFF  
5S  
INTERVAL  
ALARM SIGN  
INTERVAL  
ALARM SIGN  
OFF  
OFF  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
Use the cursor button (j or l) to move the cursor to  
INTERVAL, then use the cursor button (d or c) to select the  
time interval (e.g. 15S).  
Use the cursor button (j or l) to move the cursor to  
ZOOM, then use the cursor button (d or c) to select the  
zoom magnification power (e.g. x2).  
Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,  
Available settings: OFF, x1.4, x2, x2.8, x4, x6  
5M  
Note:  
Note: When a motion is detected, no other motions will be  
When a suspicious motion is detected, the camera zooms in  
according to the set magnification power. The zoom takes  
effect for 5 seconds and then returns to the previous  
magnification level.  
detected within the set interval of time.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
The zoom focuses on the center of the screen. If the  
maximum optical performance is exceeded, zooming will stop  
at maximum magnification.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
ALARM SIGN setting  
This item is set in the MOTION SETTING screen.  
MOTION SETTING  
SIZE  
SET  
ON  
MASKING  
SENSITIVITY  
ZOOM  
SET  
OFF  
5S  
INTERVAL  
ALARM SIGN  
OFF  
PRESET  
MENU  
OFF  
BACK  
Use the cursor button (j or l) to move the cursor to OFF  
for ALARM SIGN, and then use the cursor button (d or c)  
to select ON.  
Available settings:  
ON: The camera ID display blinks when motion is detected.  
OFF: The camera ID display does not blink when motion is  
detected.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
E Profile compensation setting (APERTURE)  
Set this function to further emphasize the profile of the target object. The amount of compensation can be adjusted for horizontal or  
vertical directions.  
MAIN MENU  
VIEW SETTING 1  
AUTO ‚  
APERTURE SETTING  
H í------ú------ü  
V í------ú------ü  
1
2
3
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
IRIS  
8
8
WHITE BALANCE  
SHUTTER  
ATW  
OFF  
OFF  
ON  
PRIVACY MASK  
LENS  
MOTION  
APERTURE  
GAMMA  
MIRROR  
ON  
VIEW SETTING  
OPTION  
PRESET  
PRESET  
MENU  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (j or l) to move the cursor to  
3 Select the amount of profile compensation  
Available settings: 1 – 15 (Compensation intensity)  
1 Set the horizontal profile compensation  
VIEW SETTING, then press the SET button. (e.g. 1)  
The VIEW SETTING 1 screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
APERTURE and then use the cursor button (d or c) to  
select ON. Then press the SET button.  
Use the cursor button (d or c) to adjust the value for  
H” (horizontal).  
2 Set the vertical profile compensation  
The APERTURE SETTING screen will appear and the “H” value  
will be blinking.  
Use the cursor button (j or l) to move the cursor to “V”  
(vertical), then use the cursor button (d or c) to adjust  
the value for “V”.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEW SETTING  
F GAMMA correction setting  
In addition to turning gamma correction ON or OFF, contrast sensitivity can be boosted at 2 levels.  
MAIN MENU  
VIEW SETTING 1  
IRIS AUTO ‚  
1
2
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
WHITE BALANCE  
SHUTTER  
ATW  
OFF  
OFF  
ON  
PRIVACY MASK  
LENS  
MOTION  
APERTURE  
GAMMA  
MIRROR  
ON  
VIEW SETTING  
OPTION  
PRESET  
PRESET  
MENU  
OFF  
BACK  
MENU  
1 Use the cursor button (j or l) to move the cursor to  
VIEW SETTING, then press the SET button. (e.g. 1)  
The VIEW SETTING 1 screen will appear.  
2 Use the cursor button (j or l) to move the cursor to  
ON for GAMMA, then use the cursor button (d or c) to  
select the gamma correction.  
Available settings:  
OFF: No gamma correction  
ON: Gamma correction (γ = 0.45)  
SMART 1: Correction 1  
SMART 2: Correction 2 (improves contrast for dark  
locations)  
Note: When using SMART 1 or SMART 2, the target object may  
be too bright, so determine which setting is better for the  
target object.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
MAIN MENU  
OPTION  
RS-485 SETTING  
BAUD RATE  
RS-485 SETTING  
BAUD RATE  
1
2
3
4
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
CONTROL  
ADDRESS  
ALARM  
485  
0
SET  
19200  
OFF  
19200  
OFF  
TERMINATE  
TERMINATE  
PRIVACY MASK  
LENS  
MIRROR  
VIEW SETTING  
OPTION  
SET  
Option settings  
2 Use the cursor button (j or l) to move the cursor to  
485 for CONTROL, use the cursor button (d or c) to  
select the device to be operated (e.g. 485), and then  
press the SET button.  
CONTROL setting: This sets whether other peripheral devices  
can be used to operate the camera by means of the RS-485  
interface or a linked coaxial cable.  
ADDRESS setting: Use this to set the address for this camera  
when more than one camera is connected or when other  
peripheral devices or a system controller have been connected.  
(See p57)  
The RS-485 SETTING screen will appear.  
Available settings:  
485: For operation by the System Controller  
COAX: For operation of device by linked coax cable.  
ALARM setting: This is used for settings related to alarm  
input and alarm output. In addition, it is also used to force  
selection of COLOR mode or B/W mode when the  
3 Use the cursor button (d or c) to select 19200 for BAUD  
RATE.  
DAY/NIGHT setting function is being used. (See p57)  
Available settings: 19200, 9600, 4800, 2400  
4 Use the cursor button (j or l) to move the cursor to  
TERMINATE, and then use the cursor button (d or c) to  
select the terminate setting.  
CONTROL setting  
1 Use the cursor button (j or l) to move the cursor to  
SET for OPTION, then press the SET button.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
The OPTION screen will appear.  
Note: The PRESET ON setting cannot be used when OPTION  
settings are in use.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
ALARM setting  
MAIN MENU  
OPTION  
1
2
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
CONTROL  
ADDRESS  
ALARM  
485  
0
SET  
A Alarm input setting (ALARM IN)  
Make the following settings for alarm detection.  
PRIVACY MASK  
LENS  
MIRROR  
Connect the external alarm switch to the alarm input terminal on  
the back of the camera.  
VIEW SETTING  
OPTION  
SET  
ADDRESS setting  
1
MAIN MENU  
2
OPTION  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
CONTROL  
ADDRESS  
ALARM  
485  
0
SET  
1 Use the cursor button (j or l) to move the cursor to  
PRIVACY MASK  
LENS  
SET for OPTION, then press the SET button.  
MIRROR  
The OPTION screen will appear.  
VIEW SETTING  
OPTION  
SET  
Note: The PRESET ON setting cannot be used when OPTION  
1 Use the cursor button (j or l) to move the cursor to  
settings are in use.  
SET for OPTION, then press the SET button.  
2 Use the cursor button (j or l) to move the cursor to  
ADDRESS, and then use the cursor button (d or c) to  
select the address.  
The OPTION screen will appear.  
Note: The PRESET ON setting cannot be used when OPTION  
settings are in use.  
Available settings: 0 (d) – 127 (c)  
2 Use the cursor button (j or l) to move the cursor to  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
SET for ALARM, then press the SET button.  
The ALARM SETTING screen will appear.  
3 Alarm input setting  
Use the cursor button (j or l) to move the cursor to  
ALM for ALARM IN, and then use the cursor button (d  
or c) to set the input (e.g. ALM).  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
1
2
ALARM SETTING  
3, 4  
ALARM IN  
POLARITY  
MOTION  
ALM  
NO  
DURATION  
OFF  
5S  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
OFF  
NO  
ALARM OUT  
5S  
ALARM TIME  
OFF  
1 External alarm input  
4 POLARITY setting  
2 Motion sensor detection  
Use the cursor button (j or l) to move the cursor to  
POLARITY, then use the cursor button (d or c) to select  
“NO” or “NC”.  
OR: Outputs an alarm if either an external alarm or a  
motion sensor alarm is detected.  
6 Alarm duration setting (DURATION)  
Available settings:  
Use the cursor button (j or l) to move the cursor to  
DURATION, then use the cursor button (d or c) to  
select the alarm duration.  
NO: Normal open (Normally open so closed condition is  
detected as input.)  
NC: Normal closed (Normally closed so open condition is  
Set the duration for the following alarm input reception.  
detected as input.)  
Available settings: 5S (default setting), 10S, 15S, 20S, 30S,  
5 Motion sensor input setting (MOTION)  
1M, 2M, 3M, 4M, 5M  
Use the cursor button (j or l) to move the cursor to  
MOTION, then use the cursor button (d or c) to select  
the input.  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
Matches information from the camera’s motion sensor and  
the external alarm and outputs it.  
Available settings:  
OFF: Does not output a motion sensor alarm.  
AND: Outputs an alarm when an external alarm input and  
motion sensor alarm are detected at the same time.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
B Color/black & white selection setting (DAY/NIGHT)  
3 POLARITY setting  
The ALARM IN terminal on the rear panel can be used to force  
the image mode to color mode or black & white mode. Use this  
setting when using this terminal to force the mode selection.  
However, when this setting is being used, external alarm input  
cannot be received.  
Use the cursor button (j or l) to move the cursor to  
POLARITY, then use the cursor button (d or c) to select  
“NO” or “NC”.  
Available settings:  
NO: Normally open (Normally open, and mode switches  
between color and black & white when closed)  
1
LENS  
2, 3  
ALARM SETTING  
NC: Normally closed (Normally closed, and mode switches  
FOCUS  
MANU ‚  
SET  
ALARM IN  
POLARITY  
MOTION  
ALM  
NO  
between color and black & white when opened)  
ZOOM  
OFF  
5S  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
PRESET  
DAY/NIGHT  
COLOR‚  
OFF  
OFF  
NO  
Between ALARM  
IN - COM terminals  
Mode after  
selection  
POLARITY setting  
VIEW ANGLE  
5S  
OFF  
OFF  
BACK  
PRESET  
MENU  
OFF  
BACK  
MENU  
When set to NO Open  
COLOR  
Closed  
B/W  
1 Set DAY/NIGHT in the LENS setting screen to “COLOR”.  
When set to NC  
Open  
COLOR  
B/W  
First change the DAY/NIGHT setting in the LENS setting screen  
to “COLOR”. (See p23)  
Closed  
2 Color/black & white selection setting  
Note:  
Use the cursor button (j or l) to move the cursor to  
ALM for ALARM IN, and then use the cursor button (d  
or c) to set the input (e.g. COLOR).  
If DAY/NIGHT has been set to “COLOR”, color/black &  
white selection will not be possible.  
If COLOR is selected, settings relating to external alarm  
input will not be displayed, and it will not be possible to  
receive external alarm inputs.  
ALM: The control terminal (ALARM IN) is used for alarm input.  
COLOR: The control terminal (ALARM IN) is used for  
color/black & white selection input. External operations can  
then be used to forcibly switch the mode to color mode or  
black & white mode.  
The color/black & white selection setting is applied from the  
point after the menu is exited.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
C Alarm output setting (ALARM OUT)  
1
ALARM SETTING  
2
ALARM SETTING  
3
ALARM SETTING  
ALARM IN  
POLARITY  
MOTION  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
ALM  
NO  
ALARM IN  
POLARITY  
MOTION  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
ALM  
NO  
ALARM IN  
POLARITY  
MOTION  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
ALM  
NO  
OFF  
5S  
OFF  
5S  
OFF  
5S  
OFF  
NO  
OFF  
NO  
OFF  
NO  
5S  
5S  
5S  
OFF  
OFF  
OFF  
1 ALARM OUT setting  
3 ALARM TIME setting  
Use the cursor button (j or l) to move the cursor to  
ALARM OUT, then use the cursor button (d or c) to  
select “ON” or “ OFF”.  
Use the cursor button (j or l) to move the cursor to  
ALARM TIME, then use the cursor button (d or c) to  
select the amount of time for external alarm output.  
Available settings:  
Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,  
5M  
ON: Output an alarm (for activation of buzzer or lamp)  
OFF: Does not output an alarm  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
2 POLARITY setting  
Use the cursor button (j or l) to move the cursor to  
POLARITY, then use the cursor button (d or c) to select  
“NO” or “NC”.  
Available settings:  
NO: Normal open (Normally open so closed condition is  
detected as input.)  
NC: Normal closed (Normally closed so open condition is  
detected as input.)  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTION SETTING  
D Operation of alarm signal output to the System  
Controller setting (LINE OUT)  
Outputs alarm signal to the System Controller. The ALARM lamp  
on the System Controller will blink when it receives an alarm  
signal. An alarm list can be displayed to show information such as  
date/time alarm was received, the device sending the alarm and  
the alarm type.  
1
ALARM SETTING  
ALARM IN  
POLARITY  
MOTION  
ALM  
NO  
OFF  
5S  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
OFF  
NO  
5S  
OFF  
Use the cursor button (j or l) to move the cursor to LINE  
OUT, then use the cursor button (d or c) to select “ON” or  
“OFF”.  
Available settings:  
ON: Outputs alarm signal to the System Controller  
OFF: Does not output alarm signal to the System Controller  
To close the menu screen or return to the previous  
screen, select BACK or END for MENU and press the SET  
button.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU FLOW  
LANGUAGE  
CAMERA ID SETTING  
L-L SETTING  
(V SYNC PHASE)  
ú------+------ü  
LANGUAGE  
LANGUE  
ENGLISH  
FRENCH  
SPANISH  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
0123456789 :-‚  
IDIOMA  
0
ID ????????????????  
POSITION  
SET  
MENU  
BACK  
PASSWORD  
PASSWORD  
(NEW PASSWORD)  
1234  
-
SET ‚  
****  
-
SET ‚  
MAIN MENU  
PRIVACY MASK SETTING  
PASSWORD LOCK ON ‚  
OK  
LANGUAGE  
CAMERA ID  
SYNC  
SET  
OFF  
INT  
SET  
SET  
OFF  
1
SET  
OFF  
END  
PASSWORD CHANGE SET ‚  
MASK SET SET ‚  
PASSWORD  
PRIVACY MASK  
LENS  
MIRROR  
(NOW PASSWORD)  
MASK 3 SET  
(POSITION)  
VIEW SETTING  
OPTION  
****  
-
SET ‚  
PRESET  
MENU  
MENU  
BACK  
MASK NO.SELECT  
MASK  
MASK  
MASK  
MASK  
1
2
3
4
OFF  
SET  
OFF  
OFF  
OFF  
OPTION  
CONTROL  
ADDRESS  
ALARM  
485  
0
SET  
LENS  
FOCUS SETTING  
AREA SETTING  
FOCUS  
MANU ‚  
LIMIT NEAR  
SENSITIVITY  
AREA  
1M  
AREA  
3
RS-485 SETTING  
HIGH  
SET  
ZOOM  
SET  
BAUD RATE  
TERMINATE  
19200  
OFF  
MANU  
DAY/NIGHT  
AUTO ‚  
OFF  
VIEW ANGLE  
PRESET  
MENU  
OFF  
BACK  
ZOOM SETTING  
FOCUS SETTING  
LIMIT NEAR 1M  
PRESET  
MENU  
OFF  
BACK  
SPEED  
EL ZOOM  
V-RESO.UP  
3
OFF  
OFF  
SPEED  
2
ALARM SETTING  
ALARM IN  
POLARITY  
MOTION  
DURATION  
ALARM OUT  
POLARITY  
ALARM TIME  
LINE OUT  
ALM  
NO  
AUTO, COLOR, B/W  
OFF, ON  
OFF  
5S  
ON  
NO  
5S  
See page 63  
OFF  
A
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU FLOW  
A
CENT  
MASK  
BLC MASKING  
VIEW SETTING 1  
IRIS SETTING  
BLC SETTING  
BLC SETTING  
(POSITION)  
IRIS  
AUTO ‚  
BLC  
SENSE UP  
OFF  
OFF  
(BLC WEIGHT)  
í------ú------ü  
WHITE BALANCE  
SHUTTER  
MOTION  
ATW  
OFF  
OFF  
ON  
7
7
(LEVEL)  
(BRIGHT)  
í------ú------ü  
MULT  
APERTURE  
GAMMA  
ON  
í------ú------ü 40  
CONTINUE (ñ)  
PRESET  
MENU  
OFF  
BACK  
IRIS SETTING  
OFF  
EI  
(IRIS STOP)  
í------ú------ü 17  
MANU  
BLC SETTING  
(SIZE)  
BLC WINDOW WEIGHTING  
(LEVEL)  
í------ú------ü 60  
TOP  
0
0
0
0
7
BOTTOM  
LEFT  
RIGHT  
CENTER(FIX)  
PRESET  
MENU  
OFF  
BACK  
ATW SETTING  
AWC SETTING  
MWB SETTING  
(OFFSET)  
MASKING  
OFF  
OFF  
AWC LOCK  
GO TO MWB  
SET  
SET  
SMART ATW  
R í---ú--+------ü 70  
B í---ú--+------ü 66  
ES SETTING  
ES SETTING  
SHUTTER SPEED  
SHORT  
LONG  
SHUTTER SPEED  
60  
x1  
MOTION SETTING  
MOTION SIZE  
MOTION MASKING  
SENSITIVITY  
í---ú----ü  
Y-LEVEL í---ú----ü  
Y-DIFFER í---ú----ü  
DURATION ú--------ü  
SIZE  
SET  
ON  
SET  
OFF  
5S  
MOVE  
5
5
5
1
MASKING  
SENSITIVITY  
ZOOM  
V
H
1
1
INTERVAL  
ALARM SIGN  
OFF  
DEMO  
OFF  
PRESET  
MENU  
OFF  
BACK  
CONTINUE (ñ)  
PRESET  
MENU  
OFF  
BACK  
APERTURE SETTING  
H í------ú------ü  
V í------ú------ü  
8
8
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Pickup device  
Effective pixels  
Horizontal resolution  
Lens  
: 1/4"  
: 768 (H) x 494 (V)  
: Over 520 TV lines  
: x22 zoom lens, f=3.6 – 79.2mm (F1.6 – 3.8)  
Electronic zoom and gearing  
Motion detector  
Privacy masking  
: ON/OFF, ON allows setting of detection  
patterns on a 48 zone screen for 6 motion  
settings (size, masking, sensitivity, zoom,  
interval, alarm sign)  
: ON/OFF, max of 4 masked locations  
Password lock possible  
Zoom speed setting possible  
Alarm input/output  
(back panel control  
terminals)  
Electronic zoom  
: 16 power (combined with optic zoom gives  
352 power max)  
Max zoom magnification setting possible  
Vertical resolution ON/OFF setting  
: AUTO/MANUAL  
AF area setting possible (3 step)  
: Alarm input: 1 (for external alarm switch)  
Alarm output: 1 (for sending a signal to the  
system controller or an alarm detection  
device such as a buzzer)  
Autofocus  
Iris control  
Mirror image effect  
: Horizontally (H), vertically (V), horizontally  
and vertically (HV)  
: AUTO/MANUAL, 1/2 EV steps  
Synchronization method : Internal synchronization/Line lock,  
Camera ID  
View settings  
: ON/OFF, 16 characters  
: 9 (0 – 8) screen files can be established, and  
each file can set 7 capturing characteristics  
such as iris  
V phase adjustment possible  
Lowest image illumination: 1.2 lx (F1.6, AGC gain at maximum, COLOR  
mode)  
0.06 lx (F1.6, B/W mode)  
0.04 lx (F1.6, x32 electronic sensitivity  
increased, COLOR mode)  
Communications  
Operational  
temperature/humidity  
Power source  
Power consumption  
Weight  
: Coaxial control, RS-485  
: –10 – +50°C/below 90% RH  
: 24 V AC, 60 Hz/12 – 15 V DC  
: 4.5 W  
0.002 lx (F1.6, x32 SENSE UP, B/W mode)  
S/N  
Backlight compensation : Multi-spot evaluative metering  
5 spot centerweighted average metering  
: Over 48dB  
: 380 g  
48 multi-spot metering  
Day/Night  
Electronic shutter  
: AUTO / COLOR / B/W settings available  
SERVICE  
:
Fast shutter speed mode (SHORT);  
1/60, 1/100, 1/250, 1/500, 1/1000,  
1/2000, 1/4000, 1/10000  
This camera is a precision instruments and if treated with care,  
will provide years of satisfactory performance. However, in the  
event of a problem, the owner is advised not to attempt to make  
repairs or open the cabinet. Servicing should always be referred to  
your dealer or Sanyo Authorized Service Centre.  
Slow shutter speed mode (LONG);  
x1, x2, x4, x8, x16, x32  
Electronic sensitivity  
boosting  
: AUTO/OFF, works with auto iris  
Up to x32 max setting possible  
White balance  
AGC gain  
: ATW/AWC/MWB  
: OFF/–6/ 0/+6/+9/+12/+15dB  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
MAIN FEATURES  
Dimensions  
Built in Interline transfer method 1/4” CCD, approx. 410,000  
picture elements.  
54 mm  
6 mm  
125.3 mm  
116 mm  
High sensitivity, minimum required illumination is 1.2 lux.  
(F1.6, gain max)  
9.3 mm  
More than 520 TV lines of horizontal resolution.  
Equipped with intelligent Backlight compensation.  
Special Gamma mode (contrast up)  
Built in high speed electronic shutter and slow shutter.  
32X Electronic sensitivity  
Built in Digital Motion Detection  
Built in Privacy masking function  
1/4"-20UNC  
12VDC/24V AC dual operation(electrically isolate) .  
Internal sync. / Line Lock.  
External appearance and specifications subject to change  
without notice.  
22x optical zoom and 16x electronic zoom.  
Coaxial control or RS485, operation via SSP.  
The Day/Night function is a function that can adapt to a wide  
range of changing luminance levels by automatically switching  
to color during daytime, or to black and white at times of low  
luminance such as nighttime.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SANYO INDUSTRIAL VIDEO  
COLOR VIDEO CAMERA LIMITED WARRANTY  
OBLIGATIONS  
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and  
addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.  
For product operation, authorized service center referral, service assistance or problem resolution, call  
CUSTOMER INFORMATION 1-800-421-5013  
Weekdays 8:30 AM – 5:00 PM Pacific Time  
For accessories and/or parts, call  
PARTS ORDER INFORMATION 1-800-726-9662  
Weekdays 8:30 AM – 5:00 PM Pacific Time  
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES  
ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER  
AT THE TIME WARRANTY SERVICE IS REQUESTED.  
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or  
replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.  
LABOR  
3 YEARS  
PARTS  
3 YEARS  
IMAGE DEVICE  
3 YEARS  
EXCLUSIONS  
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced  
or removed.  
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.  
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.  
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized  
service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,  
flood or other Acts of God, or normal wear and tear.  
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.  
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE  
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS  
WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH  
THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT,  
SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.  
ATTENTION  
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.  
Model No._____________________________________________________________________  
Date of Purchase _______________________________________________________________  
Serial No. _____________________________________________________________________  
(Located on back or bottom side of unit.)  
Purchase Price _________________________________________________________________  
Where Purchased _________________________________________________________________________________________________________________________________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed on recycled paper  
Imprimé sur du papier recyclé  
Impreso en papel reciclado  
SANYO Electric Co., Ltd.  
1AC6P1P2630--  
Printed in Japan  
L5AD2/US(1202KP-CZ)a  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Clock Radio 12 1632 User Guide
Rival Can Opener CN738 User Guide
Roberts Radio Radio RD 59 User Guide
Roland Printer SJ 645EX User Guide
Rover Lawn Mower ProCut 50 User Guide
Samsung Cable Box DCB B270R User Guide
Samsung Fax Machine SF4000 User Guide
Samsung Tablet GTP3100TSLTTT User Guide
Sanyo Computer Monitor VMC 8114PA User Guide
Screenlife Video Games Seinfeld User Guide