Multimedia Projector
MODEL PDG-DHT100L
✽ Projection lens is optional.
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective
corporation.
DLP is a registered trademark ofTexas Instruments. BrilliantColor and DynamicBlack are trademarks ofTexas Instruments.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ToThe Owner
Safety Precaution
WARNING: l THIS APPARATUS MUST BE EARTHED
Before installing and operating the projector, read this
manual thoroughly.
The projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in good condition for
many years to come.
Improper operation may result in not only shortening the
product life, but also malfunctions, fire hazard, or other
accidents.
lTO REDUCETHE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSETHIS APPLIANCETO
RAIN OR MOISTURE
–
This projector produces intense light from the projection lens.
Do not stare directly into the lens, otherwise eye damage could
result. Be especially careful that children do not stare directly
into the beam.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and
try the solutions in the “Troubleshooting” section in the
back of this manual. If the problem still persists, contact the
dealer where you purchased the projector or the service
center.
–
–
Install the projector in a proper position. Otherwise it may
result in a fire hazard.
Allowing the proper amount of space on the top, sides, and
rear of the projector cabinet is critical for proper air circulation
and cooling of the unit. The diagrams shown here indicates the
minimum space required. If the projector is to be built into a
compartment or similarly enclosed, these minimum distances
must be maintained.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
– Do not cover the ventilation slots on the projector. Heat build-
up can reduce the service life of your projector, and can also be
dangerous.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK) NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
SIDE andTOP
REAR
1.5’ (50cm)
3.3’ (1m)
1.5’ (50cm)
1.5’ (50cm)
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHINTHIS UNIT.
–
If the projector is unused for an extended time, unplug the
projector from the power outlet.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER’S MANUAL WITH
THIS UNIT.
CAUTION ON HANGING FROMTHE CEILING
When hanging the projector from the
ceiling, clean the air intake vents and
top of the projector periodically with a
vacuum cleaner. If you leave the projector
unclean for a long time, the cooling fans
can be clogged with dust, and it may
cause a breakdown or a disaster.
The symbol mark and recycling systems described below
apply to EU countries and do not apply to countries in other
areas of the world.
Your product is designed and manufactured with high qual-
ity materials and components which can be recycled and/or
reused.
The symbol mark means that electrical and electronic
equipment, batteries and accumulators, at their end-of-life,
should be disposed of separately from your household
waste.
DO NOT SET THE PROjECTOR IN GREASy, WET, OR
SMOKy CONDITIONS SUCH AS IN A KITCHEN TO
PREVENT A BREAKDOWN OR A DISASTER IF THE
PROjECTOR COMES IN CONTACT WITH OIL OR
CHEMICALS, IT MAy BECOME DETERIORATED
Note:
If a chemical symbol is printed beneath the symbol mark,
this chemical symbol means that the battery or accumula-
tor contains a heavy metal at a certain concentration. This
will be indicated as follows: Hg: mercury, Cd: cadmium, Pb:
lead.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
In the European Union there are separate
collection systems for used electrical and
electronic equipment, batteries and accumu-
lators.
Please, dispose of them correctly at your
local community waste collection/recycling
centre.
Ne peut être utilisé dans une salle d’ordinateurs telle
que définie dans la norme ANSI/NFPA 75 Standard for
Protection of Electronic Computer/Data Processing
Equipment.
Please, help us to conserve the environment we live in!
READ AND KEEPTHIS OWNER'S MANUAL FOR LATER USE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read
before the product is operated.
This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a child
or adult, and serious damage to the projector. Use only with
a cart or stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
e. If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance and
cart combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to ensure reliable operation of the
equipment and to protect it from overheating.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety
checks to determine that the projector is in safe operating
condition.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
NOTE FOR CUSTOMERS INTHE US
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Hg LAMP(S) INSIDETHIS PRODUCT CONTAIN MERCURY
ANDMUSTBERECYCLEDORDISPOSEDOFACCORDING
TO LOCAL, STATE OR FEDERAL LAWS.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
IMPORTANT!
Filter Maintenance!!
Openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect
it from overheating, these openings must not be
blocked or covered.
The projector uses a lamp which generates
significant heat. The cooling fans and air vents are
provided to dissipate the heat by drawing air into the
housing and the filter is located in the intake vents to
prevent dust from getting inside of the projector.
CAUTION
In order to care for the projector appropriately,
regular cleaning is required. Remove any dirt or dust
that has accumulated on the projector.
Hot air is exhausted from the exhaust vent. When
using or installing the projector, the following
precautions should be taken.
If the projector reaches a time set in the timer
setting, a Filter replacement icon (Fig. 1) appears on
the screen and WARNING FILTER indicator on the
top panel lights up (see below), indicating that the
filter replacement is necessary.
–Do not put any flammable object or spray can near
the projector, hot air is exhausted from the air vents.
–Keep the exhaust vent at least 3’ (1 m) away from
any objects.
–Do not touch peripheral parts of the exhaust vent,
especially screws and metallic parts. These areas will
become hot while the projector is being used.
–Do not put anything on the cabinet. Objects put on
the cabinet will not only get damaged but also may
cause fire hazard by heat.
–Do not cover vents with papers or other materials.
–Make sure that there are no objects under the
projector. An object under the projector may prevent
the projector from taking cooling air through bottom
vent.
If the projector detects that the filter is clogged and
no scroll is left in the filter cartridge, a Filter cartridge
replacement icon (Fig. 2) appears on the screen and
WARNING FILTER indicator on the top panel lights
up (see below). Stop using the projector immediately
and replace the filter cartridge.
Blocking the air vents and leaving the projector
uncleaned for a long time may not only damage the
projector and may require costly repairs but may also
cause accidents or fire.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
For maintenance of the filter, refer to “Filter counter”
on page 61 and “Maintenance and Care” on pages
62–64.
Damages to the projector caused by using an
uncleaned filter or improper maintenance will
void the warranty on the projector
Top Panel
Fig 1 Filter replacement icon
AIR INTAKE VENT
EXHAUST VENT
Fig ꢀ Filter cartridge replacement
icon
WARNING FILTER
indicator
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Installing the Projector in Proper Directions
Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in
severe accident or fire hazard.
This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the
horizontal plane.
✔Note:
•To inverse or reverse the image, set the ceiling function to “On.” (pp.41, 45)
•The projector cannot be operated at an altitude above 3,000 meters.
Positioning Precautions
Avoid positioning the projector as described below when installing.
10˚
10˚
20˚
20˚
Do not roll the projector more
than 20 degrees from side to
side.
In upward projection, do
not tilt the projector over 10
degrees right and left.
Do not put the projector
on either side to project an
image.
In downward projection, do
not tilt the projector over 10
degrees right and left.
10˚
10˚
CAUTION ON CEILING MOUNTING
For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted
properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty
on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit
or installation of the ceiling mount kit in an improper location.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Moving the Projector
Retract the adjustable feet to prevent damage
How to move the projector by one person
to lens and cabinet. For safety, holding the
projector on both sides by 2 or more people is
recommended to move the projector because
the projector is heavy. When moving the
projector by one person from necessity, hold
the handle carefully. Moving it improperly may
result in damage of cabinet or person's injury.
CAUTION IN CARRyING OR
TRANSPORTINGTHE PROjECTOR
–Do not drop or bump the projector, otherwise
damages or malfunctions may result.
–When carrying the projector, use a suitable carrying
case.
–Do not transport the projector by courier or any
other transport service in an unsuitable transport
case. This may cause damage to the projector. For
information about transporting the projector by
courier or any other transport service, consult your
dealer.
When moving the projector by one person, grip
handles and carry it with lens side up. Then, lay
it down on the correct position.
–Do not put the projector in a case before it is
cooled enough.
–Do not transport the projector with a replacement
lens installed.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instructions. If such changes or modifications should be made, you could be required to stop operation
of the equipment.
Canadian Radio Interference Regulations
This Class A digital apparatus meets all requirements of the Canadian ICES-003.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin
face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the
ASA
same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e.
red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted.
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············· Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
WARNING:THIS APPARATUS MUST BE EARTHED
THE SOCKET-OUTLET SHOULD BE INSTALLED NEARTHE EQUIPMENT AND EASILy ACCESSIBLE
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
q Projection Lens (Option)
w Indicators
e Infrared Remote Receiver (Front)
r Handle
Front
!
t Adjustable Feet
y Side Control
u Terminals and Connectors
i Main On/Off Switch
o Power Cord Connector
! Lamp Cover
✽
✽Kensington Security Slot
This slot is for a Kensington lock used to
deter theft of the projector.
*Kensington is a registered trademark of ACCO Brands
Corporation.
q
w e
r
t
y
u
i o t
! Infrared Remote Receiver (Rear)
! Air IntakeVent
! Air Filter Cover
Back
! !
! ExhaustVent
CAUTION
Hot air is exhausted from the exhaust
vent. Do not put heat-sensitive objects
near this side.
!
!
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Terminals and Connectors
q
w
e
r
t
y
u
i
o
!
!
!
q USB CONNECTOR (Series B)
u S-VIDEO INPUT jACK
USB connector is used to service the projector.
Connect the S-VIDEO output signal from video
equipment to this jack. (p.21)
w 5 BNC INPUT jACKS
Connect the component or composite video
output signal from video equipment to VIDEO/Y,
Pb/Cb, and Pr/Cr jacks or connect the computer
output signal (5 BNCType [Green, Blue, Red, Horiz.
Sync, and Vert. Sync.]) to G, B, R, H/V, and V jacks.
(pp.20–21)
i
o
SERIAL PORT INTERMINAL
If you control the projector by computer, you must
connect a cable (not supplied) from your computer
to this terminal.
SERIAL PORT OUT TERMINAL
This terminal outputs signal from SERIAL PORT IN.
More than two projectors can be controlled with
one computer by connecting SERIAL PORT IN of
another projector to this terminal.
e
D-sub 15-PIN INPUT TERMINAL
Connect computer output (Analog D-sub 15-pin
type) to this terminal. (pp.20-21)
r
MONITOR OUT TERMINAL
! R/C jACK
This terminal can be used to output the incoming
analog RGB, component, or composite video
out signals from INPUT 1-2 terminal to the other
monitor. (pp.20-21)
When using the wired remote control, connect the
wired remote control to this jack with a remote
control cable (not supplied).
t
DVI INPUT TERMINAL
Connect computer output (Digital/DVI-D type) to
this terminal. (p.20)
! LAN port
Connecting the LAN cable. See the owner's
manual of the Network Board for details.
HDTV (HDCP Compatible) signal can be also
connected. (p.21)
! Serial port
This is used when controlling the external
equipment via the network.
y HDMI
Connect the HDMI output signal from video
equipment to this terminal. (p.21)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Side Control and Indicators
Indicators
Side Control
Side Control
i
o
!
q
w
e
r
t
y
u
!
!
q
w
button
u
button
AUTO PC ADj
ON/STAND-By
Turn the projector on or off. (pp.24,25)
Automatically adjust the computer image to its
optimum setting. (pp.28, 36)
SHUTTER button
Close and open up the built-in shutter. (p.28)
i
button
LIGHT
Light the side control and around terminals. (p.28)
e ZOOM button
button
o LENS SHIFT
Zoom in and out the images. (p.28)
Select the LENS SHIFT function. (p.28)
r
button
FOCUS
Adjust the focus. (p.28)
!
!
button
INPUT
Select an input source INPUT 1, INPUT 2, Input 3
or Input 4. (pp.32-34)
t
y
button
MENU
Open or close the On-Screen MENU. (pp.26, 27)
button
SELECT
Used to execute the selected item. (p.26) It is also
used to expand image in DIGITAL ZOOM mode. (p.41)
buttons
POINT
- Select an item or adjust the value in the On-
Screen MENU. (p.26)
- Pan the image in DIGITAL ZOOM + mode. (p.41)
! INFORMATION button
Display the input source information (p.29).
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Indicators
q
w
POWER indicator
This indicator lights green when the projector
is ready to be turned on. And it flashes green in
Power Management mode. (pp.57, 77-79)
q
w
e
r
t
y
u
LAMP Indicator
This indicator is dim when the projector is turned
on. And bright when the projector is in stand-by
mode. (pp.77-79)
e
r
WARNINGTEMP indicator
This indicator flashes red when internal projector
temperature is too high. (pp.70, 77-79)
WARNING FILTER indicator
–Blink slow when the filter is being scrolled.
(pp.62, 77)
–Blink fast when the filter scroll is not working
properly or the filter cartridge is not installed.
(pp.62, 79)
–Light orange when the clogging of the filter is
detected or the filter counter reaches a time set
in the timer setting, urging immediate filter/ filter
cartridge replacement. (pp.61, 62, 79)
t
y
SHUTTER indicator
Light blue when the shutter is closed. (p77)
LAMP 1 REPLACE indicator
Turn orange when the life of the projection lamp1
draws to an end. (pp.66, 78)
u
LAMP ꢀ REPLACE indicator
Turn orange when the life of the projection lamp2
draws to an end. (pp.66, 78)
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control
q
w
ON/STAND-By button
Turn the projector on or off. (pp.24-25)
AUTO PC button
Automatically adjust the computer image to its optimum setting.
(pp.30, 36)
e
w
q
e
r
LIGHT button
Light the buttons on the remote control for about 10 seconds.
MENU button
Open or close the On-Screen MENU. (pp.26-27)
r
t
!
!
t POINT ed 7 8 buttons
–Select an item or adjust the value in the ON-SCREEN MENU. (p.26)
–Pan the image in DIGITAL ZOOM +/– mode. (p.41)
y
u
i
o
LENS SHIFT button
Select the LENS SHIFT function. (p.30)
FOCUS buttons
Adjust the focus. (p.30)
!
!
ZOOM buttons
Zoom in and out the images. (p.30)
y
u
FREEZE button
Freeze the picture on the screen. (p.30)
i
!
! D ZOOM
button
Select the Digital zoom +/- mode and resize the image. (pp.30, 41)
!
!
P-TIMER button
Operate the P-TIMER function. (p.31)
o
!
!
!
!
KEySTONE button
Correct keystone distortion. (pp.31, 41, 45)
! FILTER button
!
Scroll the filter. (p.31)
@
@
!
!
SHUTTER button
Close the built-in shutter for light blocking. (pp.28, 31)
button
SELECT
–Execute the selected item. (p.26)
–Expand or compress the image in the DIGITAL ZOOM mode. (p.41)
! SCREEN button
Select the screen size. (pp.40-41, 44-45)
@
!
!
IMAGE ADj button
Enter the image level adjustment mode. (pp.31, 46-48)
✔Note:
To ensure safe operation, observe the
following precautions:
INPUT 1, ꢀ, ꢁ, 4 buttons
Select an input source. (pp.32-34)
•Do not bend, drop, or expose the
remote control to moisture or heat.
•For cleaning, use a soft dry cloth. Do
not apply benzene, thinner, spray, or
any other chemical materials.
! INFO button
Display the input source information. (p.30)
@
@
@
IMAGE SEL button
Select the image level. (pp.31, 39, 43)
PIP button
Operate the Picture In Picture function. (p.30)
Wired Remote jack
Connect the remote control cable (not supplied) to this jack when
using as a wired remote control.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
1
2
3
Two AA size batteries
For correct polarity (+ and –),
Pull up the lid
and remove it.
be sure battery terminals are
in contact with pins in the
compartment.
To ensure safe operation, please observe the following precautions :
l Use two (2) AA or LR6 type alkaline batteries.
l Always replace batteries in sets.
l Do not use a new battery with a used battery.
l Avoid contact with water or liquid.
l Do not expose the remote control to moisture or heat.
l Do not drop the remote control.
l If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
l Risk of an explosion if battery is replaced by an incorrect type.
l Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Remote Control Receivers and Operating Range
Point the remote control toward the projector (to
Infrared Remote Receivers) when pressing the buttons.
Maximum operating range for the remote control is
about 16.4’ (5 m) and 60 degrees from the front, rear or
top of the projector.
Infrared Remote Receivers are provided in the front
and back and on the top of the projector. You can
conveniently use these receivers. (pp.10, 56)
16.4’
(5 m)
✔Note:
•
•
When hanging the projector from the ceiling, select the
Infrared Remote Receiver which is located farther away
from the fluorescent light. (p.56)
When using the projector in the horizontal position without
hanging from the ceiling, it is recommended to deactivate
the top Infrared Remote Receiver to avoid the effects of
the fluorescent light. (p.56)
16.4’
(5 m)
Wired Remote Control
The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside
of the operating range (16.4’/ 5 m). Connect the remote control and the projector with the remote control cable (sold
separately). Connected with the remote control cable, the remote control does not emit wireless signal.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Code
The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the remote
control codes prevents interference from other remote controls when several projectors or video equipment
next to each other are operated at the same time. Change the remote control code for the projector first before
changing that for the remote control. See “Remote control” in the Setting Menu on page 56.
Use position
Reset position
Check the Reset Switch to "Use position" in the
compartment lid on the back of the remote control.
1
2
While holding down the MENU button, press
and release the IMAGE ADJ. button the number
of corresponding times you would like to set the
number of the remote control code for the projector.
Reset switch
Number ofTimes
Remote Control Code Pressing IMAGE ADj
button
Code 1
Code ꢀ
Code ꢁ
Code 4
Code 5
Code 6
Code 7
Code ꢂ
1
ꢀ
ꢁ
4
5
6
7
ꢂ
MENU button
IMAGE ADj
button
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
Before installation, check where the projector is used and prepare a suitable lens. For the specifications of
Projection Lens, contact sales dealer where you purchased the projector.
- Lens installation and replacement should be made by the qualified service personnel
- When setting the projector after lens installation, be sure to replace a Lens Cap to protect a surface.
- When carrying or holding up the projector, be careful not to put your hands on lens part. It may
damage lens, cabinet, or mechanical parts.
✔Note:
•When the lens is not installed properly, ‘Lens incorrectly
fitted!‘ message appears on the screen.
Positioning Projector
SCREEN
This projector is designed to project on a flat projection
surface.
✔Note:
•
Brightness in room has a great influence on picture quality.
It is recommended to limit ambient lighting in order to
provide the best image.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lens Shift Adjustment
Projection lens can be moved from side to side and up and down with the motor-driven lens shift function. This
function makes the positioning of images easy on the screen. (See page 28)
The display position can be
shifted upward up to 67.7%
elevation of the display.
The display position can
be shifted downward up to
67.7% low level of the display.
When the lens is shifted to bottom
When the lens is shifted to top
The display position can be
shifted to the left in up to
41.6% width of the display.
The display position can be
shifted to the right in up to
41.6% width of the display.
When the lens is shifted to rightmost
When the lens is shifted to leftmost
Picture Level and Pitch Adjustment
The projection angle is adjustable up to 5 degrees upward
and downward respectively by rotating front and back
feet.
To raise the projector, rotate the feet clockwise.
To lower the projector or to retract the adjustable feet,
rotate the feet counterclockwise.
To correct keystone distortion, press the KEYSTONE
button on the remote control or select Keystone from the
menu (see pages 14, 31, 41, 45).
REAR
ADJUSTABLE
FEET (Refer to
p.10)
ADJUSTABLE
FEET
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Terminals of Projector
The projector has two replaceable Interface board slots. The projector's functions can be extended by installing
the optional interface boards into the terminal slots. 1 vacant slot (Input 3) is provided in your purchasing the
projector. For the Optional Interface Boards, contact sales dealer where you purchased the projector.
INPUT/OUTPUT
TERMINALS
2TERMINAL SLOTS (Factory set)
Replacement ofTerminal
✔Note:
• In the event of replacement of interface board, turn off
the projector, press the Main On/Off Switch to Off and
unplug the AC power cord from the AC outlet.
Remove 2 Screws from an interface board.
1
Pull out the interface board.
2
Replace the interface board. Insert a new interface
board along Guide to fit Plug into Socket.
Screws
3
Tighten screws to secure the interface board.
4
Guide
NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD
Socket
When ordering or using Optional Interface Board, contact
your sales dealer. When contacting the sales dealer, tell the
Option Control Number (Op.cont.No.) in the menu that is
located on the bottom of the information menu.
(See page 29)
Plug
Figure shows HD DATA WIRELESS Receiver Board
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Computer
Cables used for connection
• VGA Cable (D-sub 15 pin) *
• DVI Cable
• BNC Cable (BNC x 5)
( *One cable is supplied; Other cables are not supplied with this projector.)
Laptop type
Desktop type
Monitor Output
Monitor
Output
Monitor
Input
Monitor
Output
v
BNC Cable
VGA
Cable
VGA
Cable
DVI
Cable
B
H/HV
G
R
V
MONITOR
ANALOG
DIGITAL
OUT
Terminals of
the projector
v
Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables.
See the next page for the signals that can output
to the MONITOR OUT terminal.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting toVideo Equipment
Monitor Out SignalTable
Cables used for connection
• Video Cable (BNC x 3, BNC x 1)
• SCART-VGA Cable
• DVI Cable
• S-Video Cable
• HDMI Cable
InputTerminal
Monitor Out
YES
Cable
RGB (PC analog)
D-sub15
RGB (SCART)
RGB (PC digital)
RGB (AV HDCP)
HDMI
NO
NO
NO
Input 1
Input 2
DVI-D
HDMI
Q
A cable with one
end D-sub 15 and
the other end (Black
box) compatible with
each equipment is
necessary.
NO
YES
YES
YES
( Cables are not supplied with the
projector.)
RGB
Video
Y-Pb/Cb-Pr/Cr
S-video
5BNC
Q
Q
NO
S-video
Video Source (example)
Video Cassette Recorder
Component video output equipment.
(such as DVD player or
DVD Player
high-definitionTV source.)
Composite
Video
Output
Component Video Output
Pb/Cb Pr/Cr
RGB SCART
21-pin Output
Digital
S-Video
Output
Output
HDMI
Output
(HDCP
compatible)
Y
Refer to the
Monitor Out
SignalTable
(above).
BNC
Cable
BNC
Cable
SCART-VGA
Cable
DVI
Cable
S-Video
Cable
HDMI
Cable
S-VIDEO
VIDEO
Y-Pb/Cb-Pr/Cr
ANALOG MONITOR DIGITAL
OUT
HDMI
Terminals of
the projector
Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Attaching the Cable Cover
Cover
insertion slot
It is recommended to attach the cable covers to protect the
terminal area from dust when hanging the projector from the
ceiling. Please connect the covers to the projector with the
provided straps to prevent the covers from falling off.
Strap
Follow these steps to attach the support cover and cable cover.
Tie a strap (supplied) to the lower bracket on the right side
of the projector’s terminal area. (See the right figure.)
1
Screw
Support
Cover
Fix the opposite end of the strap to the hole inside the
support cover with a screw (supplied).
2
Insert the support cover into the cover insertion slot and
slide it to the left.
3
Cable tie
Dress and secure all cables to a cable tie (supplied). The
cable tie is reusable and can be opened and closed as
many times as needed.
4
Tie another strap (supplied) to the upper bracket on the
right side of the projector’s terminal area.
5
Fix the opposite end of the strap to the hole inside the
cover with a screw (supplied).
6
To attach the cover, insert the rods inside the cover into
the holes on the side cover until it clicks. (See the right
figure.)
Strap
7
✔Note:
Screw
•Attach the support cover first, otherwise the cover cannot
be fixed properly.
Cover
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-120 or 200–240
V AC. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce the risk of
electrical shock, do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult
your authorized dealer or service station.
Holes
Connect the projector with all peripheral equipment before turning
on the projector.
Fixing
bracket
A fixing bracket is provided to prevent the AC power cord from
coming loose. Follow these steps to attach the fixing bracket
and connect the AC power cord to the projector.
Fit a fixing bracket in each hole.
1
Connect the AC power cord to the projector.
2
Turn the fixing bracket to lock the AC power cord in place.
(See the right figure.)
3
CAUTION
The AC outlet must be near this equipment and must be easily
accessible.
✔Note:
•Unplug the AC power cord or turn off the MAIN ON/OFF
Switch when the projector is not in use. When the projector
is in stand-by mode, it consumes a little electric power.
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U S A and Canada
For Continental Europe
For the U K
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(1ꢀ0V AC)
To the AC Outlet.
(ꢀ00–ꢀ40V AC)
To the AC Outlet.
(ꢀ00–ꢀ40V AC)
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
16
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
1
2
Connect the projector’s AC power cord into an AC
outlet and turn on the MAIN ON/OFF Switch. The
LAMP indicator lights red and the POWER indicator
lights green.
The preparation display will disappear after 20
seconds.
Press the ON/STAND-BY button on the side control
or on the remote control. The LAMP indicator
dims red and the cooling fans start to operate. The
preparation display appears on the screen and the
countdown starts.
3
4
Selected Input Source and Lamp control
After the countdown, the input source that was
selected the last time and the Lamp status icon
(see page 65) appear on the screen.
Lamp status
See page 65 for the Lamp mode status
If the projector is locked with a PIN code, PIN code
Input Dialog Box will appear. Enter the PIN code as
instructed below.
✔Note:
•The Lamp replacement icon and the Filter warning
icon may appear on the screen depending on the
usage state of the projector.
Enter a PIN code
Use the Point ed buttons on the side control or on the
remote control to enter a number. Press the Point 8
button to fix the number and move the red frame pointer
to the next box. The number changes to “✳.” Repeat
this step to complete entering a four-digit number. After
entering the four-digit number, move the pointer to “Set.”
Press the SELECT button so that you can start to operate
the projector.
PIN code Input Dialog Box
After the OK icon
disappears, you can
operate the projector.
If you fixed an incorrect number, use the Point 7 button
to move the pointer to the number you want to correct,
and then enter the correct number.
✔Note:
•When the Logo select function is set to “Off,” the
logo will not be shown on the screen (p.54).
•When the “Countdown off” or “Off” is selected
in the Display function, the countdown will not be
shown on the screen (p.49).
If you entered an incorrect PIN code, “PIN code” and the
number (✳✳✳✳) will turn red for a moment. Enter the
correct PIN code all over again.
•During the countdown period, all operations
except for Zoom, Focus, and Lens-shift functions
are invalid. If the projector has been locked with a
PIN code, however, Zoom, Focus, and Lens-shift
functions are also invalid.
•If you press the ON/STAND-BY button on the side
control or the remote control during the countdown
period, you can skip the countdown and go to the
normal operations.
•If the PIN code number is not entered within three
minutes after the PIN code dialog box appeared,
the projector will be turned off automatically.
•The “1234” is set as the initial PIN code at the
factory.
What is PIN code?
PIN (Personal Identification Number) code is a security
code that allows the person who knows it to operate the
projector. Setting a PIN code prevents unauthorized use
of the projector.
A PIN code consists of a four-digit number. Refer to the
PIN code lock function in the Setting Menu on pages 58-
59 for locking operation of the projector with your PIN
code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take special care in setting a
new PIN code; write down the number in a column
on page 86 of this manual and keep it on hand.
Should the PIN code be missing or forgotten,
consult your dealer or service center.
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning Off the Projector
Press the ON/STAND-BY button on the side control
1
or on the remote control, and “Power off?” appears
on the screen.
Press the ON/STAND-BY button on the side control
2
or on the remote control again to turn off the
projector. The LAMP indicator lights bright and the
POWER indicator turns off. After the projector is
turned off, the cooling fans operate. You cannot turn
on the projector during this cooling down period.
“Power off?” disappears after 4 seconds.
When the projector has cooled down enough, the
3
POWER indicator lights green and then you can
turn on the projector. To turn off the MAIN ON/OFF
Switch, wait until the projector is completely cooled
down.
Unplug the AC power cord from the AC outlet.
4
TO MAINTAINTHE LIFE OFTHE LAMP, ONCEYOU
TURNTHE PROJECTOR ON, WAIT AT LEAST FIVE
MINUTES BEFORETURNING IT OFF.
DO NOT UNPLUGTHE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORETHE
POWER INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING OF
THE LAMP LIFE.
✔Note:
•When the On start function is set to “On,” the projector
will be turned on automatically by connecting the AC power
cord to an AC outlet (p.57).
•The running speed of cooling fans is changed according to
the temperature inside the projector.
•Do not put the projector in a case before the projector is
cooled enough.
•If the WARNINGTEMP. indicator blinks red, see “Warning
Indicators” on page 70.
•The projector cannot be turned on during the cooling
period with the POWER indicator turned off. You can turn it
on again after the POWER indicator becomes green again.
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
Side Control
The projector can be adjusted or set via the On-Screen
Menu. For each adjustment and setting procedure, refer
to the respective sections in this manual.
MENU button
POINT buttons
Press the MENU button on the side control or the
remote control to display the On-Screen Menu.
1
Use the Point 7 8 buttons to select a Menu icon.
Use the Point ed buttons to select an item in the
selected menu.
2
SELECT button
Press the SELECT button to show the item data.
Use the Point 7 8 buttons to adjust the values.
3
Remote Control
MENU button
To close the On-Screen Menu, press the MENU
button again.
✔Note:
POINT buttons
SELECT button
•The selected item is not active until the SELECT button is
pressed.
On-Screen Menu
Menu icon
Menu bar
Pointer
(red frame )
Pointer (red frame )
Press the Point ed buttons
to move the pointer.
Item
SELECT
button
Press the SELECT button here
to display previous items.
Item data
Press the Point 7 8
buttons to adjust the
value.
Press the SELECT button here
to display next items.
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Bar
For detailed functions of each menu, see “MenuTree” on pages 74-76.
For Computer Source
q
w
e
r
t
y
u
i
o
!
q GuideWindow
y Image Adjust Menu
Used to adjust the computer image. [Contrast/ Brightness/
Color management/Auto picture control/BrilliantColor/Color
temp./White balance (R/G/B)/Offset (R/G/B)/Sharpness/
Gamma/Reset/Store] (pp.46-48).
Show the selected Menu of the On-Screen Menu.
w
Input Menu
Used to select an input source Computer or Video (pp.32-34).
PC System Menu
Used to select computer system (p.35).
PC Adjust Menu
u Screen Menu
Used to adjust the size of the image. [Normal/True/Full/
Custom/Digital zoom +/–/Keystone/Ceiling/Rear/Reset/]
(pp.40-41).
e
r
i Setting Menu
Used to set the projector’s operating configurations (pp.49-61).
Used to adjust the parameters to match with the input signal
format (pp.36-38).
o Information Menu
t Image Select Menu
Display the input source information (p.29).
Used to select an image level among Standard, Real,
Dynamic, and Image 1–10 (p.39).
! Network Menu
See the owner's manual of the Network Board.
For Video Source
q
w
e
r
t
y
u
i
o
t Image Adjust Menu
q GuideWindow
Used to adjust the picture image. [Contrast/Brightness/
Color/Tint/Color management/Auto picture control/
BrilliantColor/Color temp./White balance (R/G/B)/ Offset (R/
G/B)/Sharpness/Gamma/Noise reduction/Progressive/Reset/
Store] (pp.46-48).
Show the selected Menu of the On-Screen Menu.
w
Input Menu
Used to select an input source Computer or Video (pp.32-34).
y Screen Menu
Used to adjust the size of the image. [Normal/Zoom/Natural
Wide/Full/Custom/Keystone/Ceiling/Rear/Reset] (pp.44-45).
e
AV System Menu
Used to select the system of selected video source (p.42).
u Setting Menu
r Image Select Menu
Used to set the projector’s operating configurations (pp.49-61).
Used to select an image level among Standard, Cinema,
Dynamic, and Image 1–10 (p.43).
i Information Menu
Display the input source information (p.29).
o Network Menu
See the owner's manual of the Network Board.
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Operating with Projector Control
Zoom Adjustment
Side Control
Display “Zoom” on the screen. Press the ZOOM button
and then press the point ed buttons to zoom in and out
the image.
SHUTTER button
LIGHT button
ZOOM button
LENS SHIFT
button
FOCUS button
Focus Adjustment
Display “Focus” on the screen. Press the FOCUS button
and then press the point ed buttons to adjust the focus
of the image.
POINT buttons
Lens Shift Adjustment
Display “Lens shift” on the screen. Use the Point ed7 8
buttons to position the screen to the desired point without
having picture distortion.
The screen can be moved up or down to 67.7 percent, or
sideways up to 41.6 percent from the central axis of the
lens shift. Press and hold the LENS SHIFT button for more
than 5 seconds to return to the central position. See page
18 for details.
INFORMATION
button
AUTO PC ADj
button
Zoom
Focus
Auto PC Adjustment
Operate the Auto PC Adj. function. The computer screen
adjustment can be done easily by pressing this button.
See page 36 for details.
Light Function
Light function is used to turn on the lights on the side
control and around terminals. To turn off the lights, press
the Light button again.
✔Note:
•The buttons on the side control except for the LIGHT button
and ON/STAND-BY button do not light up when the projector
is in stand-by mode or during the cooling down period.
✔Note:
•The arrow disappears at the maximum lens shift in each
direction.
•The arrow turns red when the lens shift comes to the
center position of the screen.
Shutter Function
Shutter function allows you to completely block out light
to the screen. Press the SHUTTER button to close the
shutter inside the projector. To open up the shutter, press
the SHUTTER button again. Refer to p.60 for detail of
setting for the Shutter function.
✔Note:
• The SHUTTER button on the side control and the remote
control cannot be effective when Shutter Protection is "On"
in the Setting menu. (p.60)
• The SHUTTER indicator on the projector's top lights blue
when the shutter is closed. (pp.13, 77)
• The projector will shut down automatically when the set
time on Shutter management has passed. (p.60)
•The Power management function does not work when the
shutter is closed. (p.57)
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Information
Information Menu
Information display can be used to confirm the current
operating condition of the projector and the signal being
projected through the projector.
Information Menu
Press the INFORMATION button to display the
information window on the screen. Press the Point d
button or the INFORMATION button again to display the
next page. To hide the information window, press the
INFORMATION button again or Point 7 8 buttons.
The information window can also be selected from the
menu.
Press the Point ed buttons
to display the next or previous
page.
✔Note:
•The H- and V-sync freq. values described in this figure
may be different from the actual values.
•SERIAL NO. is used to service the projector.
•When the lamp life reaches a recommended lamp
replacement time, the time shown in Lamp1 or Lamp2
turns red.
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Operating with Remote Control
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the On-Screen Menu.
AUTO PC button
Press the AUTO PC button on the remote control to
operate the Auto PC Adj. function. The computer screen
adjustment can be done easily by pressing this button.
See page 36 for details.
Remote Control
LENS SHIFT button
AUTO PC
button
See page 28 for details.
ZOOM buttons
Press the ZOOM buttons on the remote control to zoom
in and out the image. See page 28 for details.
POINT ed7 8
buttons
FOCUS buttons
SCREEN
button
Press the FOCUS buttons on the remote control to adjust
focus of the image. See page 28 for details.
LENS SHIFT
button
FREEZE button
ZOOM
buttons
FOCUS
buttons
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the FREEZE function,
press the FREEZE button again or press any other button.
FREEZE
button
D ZOOM
button
SCREEN button
Press the SCREEN button on the remote control to select
the desired screen size. The selected screen size mode
appears on the screen for 4 seconds. See pages 40 to 41
and 44 to 45 for details.
INFO
button
PIP
button
Press and hold the SCREEN button for more than 5
seconds to return all the screen size adjustment setting
to the factory default setting.
✔Note:
•See the next page for the description of other
buttons.
D ZOOM button
Press the D.ZOOM button on the remote control to enter
to the Digital zoom +/– mode. See page 41 for details.
INFO button
Press the INFO. button on the remote control to display
the information window on the screen. See the previous
page for details.
PIP button
Press the PIP button on the remote control several times
until the desired mode of Picture in Picture appears.
Press and hold the PIP button for more than 3 seconds
to display the setting dialog box of Picture in Picture. See
page 51 for details of Picture in Picture function.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Remote Control
SHUTTER button
See page 28 for details.
SHUTTER
button
FILTER button
Press and hold the FILTER button for more than five
seconds to replace the filter mechanically. See page 56
for details.
✔Note:
IMAGE ADj
button
•The filter cannot be rewound.
•When the filter is replaced, the total accumulated time of
the filter use is automatically set to 0.
IMAGE ADj button
Press the IMAGE ADJ. button on the remote control to
adjust a image level of the screen.
KEySTONE
button
P-TIMER
button
IMAGE SEL
button
For more detail, see pp.46-48.
FILTER
button
IMAGE SEL button
Press the IMAGE SEL. button on the remote control to
select a desired image level of the screen.
For more detail, see pp.39, 43.
✔Note:
•See the previous page for the description of
other buttons.
P-TIMER button
Press the P-TIMER button on the remote control. The
Timer display “00 : 00” appears on the screen and starts
to count time (00 : 00–59 : 59).
P-Timer display
To stop the P-TIMER, press the P-TIMER button.
To cancel the P-TIMER, press the P-TIMER button again.
KEySTONE button
Press the KEYSTONE button on the remote control. The
“Keystone” appears on the screen.
• The white arrows indicate that there is no correction.
• A red arrow indicates the direction of correction.
• An arrow disappears at the maximum correction.
• If you press the KEYSTONE button on the remote
control again while the Keystone dialog box is being
displayed, the keystone adjustment will be canceled.
•The adjustable range can be limited depending on the
input signal.
Use the Point ed7 8 buttons to correct keystone
distortion. The keystone adjustment can be stored
(pp.41, 45).
• “Keystone” disappears after 10 seconds.
Reduce the upper width with
Point e button.
Reduce the lower width
with Point d button.
Reduce the left part with
Point 7 button.
Reduce the right part with
Point 8 button.
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Input
Side Control
Side Control button operation
INPUT button
INPUT 1
INPUT ꢀ
INPUT ꢁ
INPUT button
INPUT 4
Side Control Operation
Press the INPUT button on the side control. It switches to
INPUT 1, INPUT 2, INPUT 3 and INPUT 4 as you press the
INPUT button.
Remote Control button operation
Before using the INPUT button on the side control, you
must select a correct input source by On-Screen Menu
and the latest input source will be displayed.
Remote Control
INPUT 1 button
Input 1
INPUT buttons
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
HDMI
Remote Control Operation
Press the INPUT 1, INPUT 2, INPUT 3 or INPUT 4 button
on the remote control. The input source appears on the
screen as you press each button. Select the connected
input source.
✔Note:
INPUT ꢀ button
•Empty slots cannot be selected.
•When a slot is empty, the input is displayed in grayout.
Input ꢀ
RGB
y,Pb/Cb,Pr/Cr
Video
S-video
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Computer Input Source Selection
Menu Operation
When Selecting the INPUT 1 with DVI/D-sub 15 terminals
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the INPUT Menu icon.
INPUT MENU
1
2
Input Menu icon
Use the Point ed buttons to move the red arrow pointer
to the desired input and then press the SELECT button.
Then you can switch to the desired input.
Move the pointer (red arrow) to Input
1 and press the SELECT button.
Press the select button again. The Source Select Menu
appears.
3
4
Input 1
Use the Point ed buttons to select the desired source
and then press the SELECT button.
Source Select Menu
Move the pointer (red
arrow) to the desired source
and press the SELECT
button.
RGB (PC analog)
When your computer is connected to the INPUT 1 (ANALOG)
terminal, select RGB (PC analog).
RGB (PC digital)
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB (PC digital).
When Selecting the INPUT ꢀ with 5-BNC/Video/S-video terminals
INPUT MENU
Input Menu icon
Move the pointer (red arrow) to Input
2 and press the SELECT button.
RGB
When your computer is connected to the INPUT 2 (5 BNC
INPUT JACKS) terminal, select RGB.
Input ꢀ
Source Select Menu
Move the pointer (red
arrow) to RGB and press the
SELECT button.
✔Note:
•When a slot is empty, the input is displayed in grayout.
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Video Input Source Selection
Menu Operation
When Selecting the INPUT 1 with DVI/D-sub 15 terminals
INPUT MENU
When connecting to video equipment, select the type of
Video source in the Source Select Menu.
Input Menu icon
RGB (Scart)
When scart video equipment is connected to the INPUT 1
(ANALOG) terminal, select RGB (Scart).
Move the pointer (red arrow) to Input
1 and press the SELECT button.
RGB (AV HDCP)
If the HDCP-compatible signal source is connected to the
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).
Input 1
HDMI
Source Select Menu
Move the pointer (red
When the video signal is connected to the HDMI terminal,
select HDMI.
arrow) to RGB (Scart), RGB
(AV HDCP), or HDMI and
press the SELECT button.
When Selecting the INPUT ꢀ with 5-BNC/Video/S-video terminals
When connecting to video equipment, select the type of
Video source in the Source Select Menu.
INPUT MENU
y, Pb/Cb, Pr/Cr
Input Menu icon
When the video input signal is connected to theY-Pb/Cb-
Pr/Cr jacks, selectY, Pb/Cb, Pr/Cr.
Move the pointer (red arrow) to Input
2 and press the SELECT button.
Video
When the video input signal is connected to the VIDEO
jack, select Video.
Input ꢀ
S-video
Source Select Menu
When the video input signal is connected to the S-VIDEO
jack, select S-video.
Move the pointer (red
arrow) toY, Pb/Cb, Pr/Cr ,
Video, or S-video and press
the SELECT button.
✔Note:
• HDCP (High-bandwidth Digital Content Protection) is a
system for protecting digital entertainment content which is
delivered by DVI (Digital Visual Interface) from being copied.
The specification of HDCP is decided and controlled by
Digital Content Protection, LLC. Should the specification be
changed, this projector may not display the digital content
protected by HDCP.
•When a slot is empty, the input is displayed in grayout.
ꢁ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
Automatic Multi-Scan System
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+,
WXGA, UXGA, or WUXGA (refer to “Compatible Computer Specifications” on pages 80-81). If a computer is
selected as a signal source, this projector automatically detects the signal format and tunes to project a proper
image without any additional settings. (Some computers need to be set manually.)
One of the following messages may appear when:
The projector cannot recognize the connected
signal conforming to the provided PC Systems.
The “Auto” is displayed on the PC System Menu
icon and the Auto PC Adjustment function works to
display proper images. If the image is not projected
properly, a manual adjustment is required. (pp.37–
38.)
PC SySTEM MENU
Auto
PC System Menu icon
Selected system is displayed.
There is no signal input from the computer. Check
the connection between your computer and the
projector. (See “Troubleshooting” on page 71.)
-----
The preset system is manually adjusted in the PC
Adjust Menu. The adjusted data can be stored in
the Mode 1–10. (pp.37-38)
Mode 1
SVGA 1
PC systems provided in this projector is chosen.
The projector chooses a proper system provided in
the projector and displays it.
✽ Mode 1 and SVGA 1 are examples.
PC SySTEM MENU
Selecting Computer System Manually
PC system can also be selected manually.
PC System Menu icon
Selected system is displayed
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the PC System Menu icon.
1
Systems in this dialog box can be
selected.
Custom Mode (1–10) set in PC Adjust
Menu. (pp.37-38)
Use the Point ed buttons to move the red arrow pointer
to the desired system, and then press SELECT button.
2
ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical
positions to conform to your computer.
Remote Control
Direct Operation
The Auto PC adjustment function can be operated
directly by pressing the AUTO PC button on the remote
control or the AUTO PC ADJ. button on the side control.
AUTO PC button
Side Control
AUTO PC ADj
button
Menu Operation
Auto PC adj
PC ADjUST MENU
Press the MENU button to display the On-Screen Menu.
1
Use the Point 7 8 buttons to move the red frame pointer
to the PC Adjust Menu icon.
Use the Point ed buttons to move the red frame pointer
to the AUTO PC adj. icon and then press the SELECT
button twice.
PC Adjust Menu icon
2
Move the red frame pointer to the Auto PC
adj. and press the SELECT button twice.
“Please wait...” appears while the Auto PC
adjustment is in process.
To store the adjusted parameters
The adjusted parameters from the Auto PC Adjustment can
be stored in the projector. Once the parameters are stored,
the setting can be done just by selecting Mode in PC SYSTEM
Menu (p.35). See Manual PC Adjustment on pages 37-38.
✔Note:
•Fine sync, Total dots, Horizontal and Vertical position of
certain computers cannot be fully adjusted with the Auto
PC Adjustment function. When the image is not provided
properly with this operation, manual adjustments are
required. (pp.37-38.)
•Auto PC Adjustment cannot be operated in Digital Signal
Input on the DVI terminal and “480p,” “575p,” “480i,” “575i,”
“720p,” “1035i,” “1080p,” or “1080i” is selected on the PC
SYSTEM Menu.
•Depending on the condition of signals and the type and
length of cables, the signals may not be properly viewed.
ꢁ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal
formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It
allows you to recall the setting for a specific computer.
✔Note: The PC Adjust Menu cannot be operated when the digital signal input on the DVI terminal is selected on PC
System Menu.
PC ADjUST MENU
Press the MENU button to display the On-Screen Menu.
1
Use the Point 7 8 buttons to move the red frame pointer
to the PC Adjust Menu icon.
PC Adjust Menu icon
Use the Point ed buttons to move the red frame pointer
to the desired item and then press the SELECT button
to display the adjustment dialog box. Use the Point 7 8
2
Move the red frame pointer to the
desired item and press the SELECT
button.
buttons to adjust the setting value.
Fine sync
Use the Point 7 8 buttons to adjust the value, eliminating a
flicker from the image displayed (from 0 to 31).
Status (Stored/Free) of the
Selected Mode.
Total dots
Use the Point 7 8 buttons to adjust the number of total dots in
one horizontal period to match your PC image.
Selected Mode
Position H
Press the Point 7 8 buttons to adjust
the value.
Use the Point 7 8 buttons to adjust the horizontal picture
position.
PositionV
Press the SELECT button at this icon
to adjust “Clamp,” “Display area H,” or
“Display area V.”
Use the Point 7 8 buttons to adjust the vertical picture position.
Current mode
Press the SELECT button to show H-sync freq. and V-sync freq.
of the connected computer.
Clamp
Current mode
Use the Point 7 8 buttons to adjust the clamp level. When the
image has dark bars, try this adjustment.
Display area H
Press the SELECT
button at Current
mode icon to show
the information of the
connected computer.
Use the Point 7 8 buttons to adjust the horizontal area displayed
by this projector.
Display areaV
Press the SELECT button at this icon
to display the previous items.
Use the Point 7 8 buttons to adjust the vertical area displayed
by this projector.
ꢁ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Reset
To reset the adjusted data, select Reset and press the SELECT
button. A confirmation box appears and then select [Yes]. All
adjustments will return to their previous figures.
To clear the adjusted data
Mode free
To clear the adjusted data, select Mode free and then press the
SELECT button. Move the red arrow pointer to the Mode that
you want to clear and then press the SELECT button.
Store
To store the adjusted data, select Store and then press the
SELECT button. Move the red arrow pointer to one of the Mode
1 to 10 in which you want to store, and then press the SELECT
button.
Close this dialog box.
Confirmation box appears
and then select [Yes].
Quit
Exit the PC Adjust Menu.
To store the adjusted data
This Mode has stored parameters.
Close this dialog box.
Vacant
Values of “Total dots,” “Position
H,” “Position V,” “Display area
H,” and “Display area V.”
Confirmation box appears
and then select [Yes].
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Selection
Direct Operation
Press the IMAGE SEL. button on the remote control to
select the desired image level.
Remote Control
Standard
Real
IMAGE SEL
button
Dynamic
Image1
•
•
•
Image 10
Menu Operation
IMAGE SELECT MENU
Press the MENU button to display the On-Screen Menu.
1
Use the Point 7 8 buttons to move the red frame pointer
to the Image Select Menu icon.
Image Select Menu icon
Use the Point ed buttons to move the red frame pointer
2
to the desired image level and then press the SELECT
button.
Standard
Move the red frame pointer to the desired
level and press the SELECT button.
Normal picture level preset on the projector.
Real
Picture level with improved halftone for graphics.
Dynamic
For viewing contrasty images in a bright room.
IMAGE 1–10
User preset picture adjustment in the Image Adjust Menu.
(p.48)
ꢁ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Screen Size Adjustment
Select the desired screen size that conforms to the input signal source.
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the Screen Menu icon.
SCREEN MENU
1
2
Use the Point ed buttons to move the red frame pointer
to the desired function and then press the SELECT
button.
Screen Menu icon
Move the red frame pointer to the desired
function and press the SELECT button.
Normal
Provide the image at the normal computer aspect ratio of 4:3.
True
Provide the image in its original size. When the original image
size is larger than the screen size (1920 x 1080), the projector
enters to the panning mode automatically. Use the Point ed7
✔Note:
•True, Full, and Digital zoom +/– cannot be selected
when no signal is detected in the PC System
Menu. (p.35)
8 buttons to pan the image. When adjusted, the arrows will
turn red. When reached to the correction limits, the arrows will
disappear.
•The projector cannot display the resolution higher
than 1920 x 1080. If your computer’s screen
resolution is higher than 1600 x 1200, lower the
resolution before connecting the projector.
•The image data other than 1920 x 1080 dots are
modified to fit the screen size in initial mode.
•The panning function may not operate properly if
the stored Mode in the PC Adjust Menu is used.
(p.38)
Full
Provide the full screen image.
Custom
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the “Custom” is
displayed on the screen for a few seconds. To display the
Aspect dialog box, press the SELECT button at Custom again
and then the Aspect dialog box appears.
Scale H/V.............. Adjust the Horizontal/Vertical screen scale.
H&V...................... When set to “On,” the aspect ratio is
fixed. The “Scale V” appears dimmed and
becomes unavailable. Adjust “Scale H,”
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V.......... Adjust the Horizontal/Vertical screen
position.
Common .............. Save the adjusted scale to all the inputs.
Press the SELECT button at Common to
display a confirmation box. To save the
scale, press the SELECT button at “Yes.”
When Custom is selected, the saved scale
is used.
Reset.................... Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at “Yes.”
Press the SELECT button at Common or
Reset, to display a confirmation box.
✔Note:
•When no signal is detected, “Normal” is set
automatically and the Aspect dialog box disappears.
•The adjustable range for Scale H/V and Position H/V
is limited depending on the input signal.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
SCREEN MENU
Keystone
This function is used to store or reset the keystone correction
when the Main On/Off Switch is pressed to Off or the AC
power cord is unplugged. Use the Point 7 8 buttons to switch
between each option.
Store. . . Keep the keystone correction even when the Main
On/Off Switch is pressed to Off or the AC power
cord is unplugged.
Move the red frame pointer to the desired
function and press the SELECT button.
Reset . . Release the keystone correction when the Main On/
Off Switch is pressed to Off or the AC power cord is
unplugged.
Ceiling
To correct keystone distortion, press the SELECT button. The
Keystone dialog box appears. Use the Point ed7 8 buttons to
correct keystone distortion. (p.31)
Ceiling
When this function is set to “On,” the picture is top/bottom and
left/right reversed. This function is used to project the image
from a ceiling-mounted projector.
Rear
Rear
When this function is set to “On,” the picture is left/right
reversed. This function is used to project the image from the
rear of the screen.
Reset
This function returns all adjusted values to the factory default
settings. Press the SELECT button at Reset to display a
confirmation box. To reset, press the SELECT button at “Yes.”
✔Note:
•The panning function may not operate properly if
the stored Mode in the PC Adjust Menu is used.
(p.38)
Quit
•The minimum compression ratio can be limited
depending on the input signal or when the
Keystone function is working or when the custom
is selected for the screen size.
•Digital zoom +/– cannot be selected when Full or
True is selected.
Exit the Screen Size Adjustment Menu.
For zooming in and out the images
Digital zoom +
Select Digital zoom +. The On-Screen Menu disappears and
“D. zoom +” appears. Press the SELECT button to expand the
image size. Use the Point ed7 8 buttons to pan the image.
The Panning function can work only when the image is larger
than the screen size.
You can also enter the Digital zoom + mode by pressing the
D.ZOOM button on the remote control.
Digital zoom –
Select Digital zoom –. The On-Screen Menu disappears and
“D.zoom –” appears. Press the SELECT button to compress the
image size.
You can also enter the Digital zoom – mode by pressing the
D.ZOOM button on the remote control.
To exit the Digital Zoom +/– mode, press any button except the
D.ZOOM , SELECT, and Point buttons.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Video System Selection
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the AV System Menu icon.
1
2
Use the Point ed buttons to move the red arrow pointer
to the desired system and then press the SELECT button.
Video jack or S-Video jack
AV SySTEM MENU (VIDEO OR S-VIDEO)
Auto
The projector automatically detects an incoming video system,
and adjusts itself to optimize its performance.
AV System Menu icon
The selected system is displayed
PAL/SECAM/NTSC/NTSC4 4ꢁ/PAL-M/PAL-N
If the projector cannot reproduce proper video image, select
a specific broadcast signal format from among PAL, SECAM,
NTSC, NTSC 4.43, PAL-M, and PAL-N.
Move the pointer to the desired
system and press the SELECT button.
y, Pb/Cb, Pr/Cr jacks
AV SySTEM MENU (COMPONENTVIDEO)
Auto
The projector automatically detects an incoming video signal,
and adjusts itself to optimize its performance.
When the Video System is 1035i or 1080i, select the system
manually.
AV System Menu icon
The selected system is displayed.
Move the pointer to the desired
system and press the SELECT button.
COMPONENTVIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select a
specific component video signal format from among 480i, 575i,
480p, 575p, 720p, 1035i, 1080p, and 1080i.
✔Note:
•The AV System menu cannot be selected when
selecting RGB(Scart).
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Selection
Direct Operation
Press the IMAGE SEL. button on the remote control to
select the desired image level.
Remote Control
Standard
Cinema
Dynamic
Image1
IMAGE SEL
button
•
•
•
Image 10
Menu Operation
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the Image Select Menu icon.
IMAGE SELECT MENU
1
Use the Point ed buttons to move the red frame pointer
to the desired image level and then press the SELECT
button.
Image Select Menu icon
2
Move the red frame pointer to the desired
level and press the SELECT button.
Standard
Normal picture level preset on the projector.
Cinema
Picture level adjusted with fine tone.
Dynamic
For viewing contrasty images in a bright room.
IMAGE 1–10
User preset picture adjustment in the Image Adjust Menu.
(p.48)
4ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Screen Size Adjustment
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the Screen Menu icon.
SCREEN MENU
1
2
Use the Point ed buttons to move the red frame pointer
to the desired function and then press the SELECT
button.
Screen Menu icon
Move the red frame pointer to the desired
function and press the SELECT button.
Normal
Provide the image at the normal video aspect ratio of 4:3.
Zoom
Expand the image to fit the width of screen. The images may be
displayed with their top and bottom areas cut off.
✔Note:
•Zoom can work only when the aspect ratio of
video input signal is 4:3 (Width:Height). The input
signal of 4:3 Letter Box will be expanded to fit
the width of screen by expanding the image
uniformly.
NaturalWide
Expand the right and left side of images naturally without
changing the center areas.
•Zoom cannot be selected when the input signal
is “720p,” “1035i,” “1080p”, or “1080i”.
•Natural Wide can work only when the aspect
ratio of video input signal is 4:3 (Width:Height).
The input signal of 4:3 will be converted to 16:9
and projected.
Full
Provide the full screen image.
Custom
•Natural Wide cannot be selected when the input
signal is “720p,” “1035i,” “1080p”, or “1080i”.
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the “Custom” is
displayed on the screen for a few seconds. To display the
Aspect dialog box, press the SELECT button at Custom again
and then the Aspect dialog box appears.
Scale H/V.............. Adjust the Horizontal/Vertical screen scale.
H&V...................... When set to “On,” the aspect ratio is
fixed. The “Scale V” appears dimmed and
becomes unavailable. Adjust “Scale H,”
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V.......... Adjust the Horizontal/Vertical screen
position.
Common .............. Save the adjusted scale to all the inputs.
Press the SELECT button at Common to
display a confirmation box. To save the
scale, press the SELECT button at “Yes.”
When Custom is selected, the saved scale
is used.
Reset.................... Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at “Yes.”
Press the SELECT button at Common or
Reset, to display a confirmation box.
✔Note:
•When no signal is detected, “Normal” is
set automatically and the Aspect dialog box
disappears.
•The adjustable range for Scale H/V and Position
H/V is limited depending on the input signal.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Keystone
SCREEN MENU
This function is used to store or reset the keystone correction
when the Main On/Off Switch is pressed to Off or the AC
power cord is unplugged. Use the Point 7 8 buttons to switch
between each option.
Store. . . Keep the keystone correction even when the Main
On/Off Switch is pressed to Off or the AC power
cord is unplugged.
Reset . . Release the keystone correction when the Main On/
Off Switch is pressed to Off or the AC power cord is
unplugged.
Move the red frame pointer to a function and
press the SELECT button.
To correct keystone distortion, press the SELECT button. The
Keystone dialog box appears. Use the Point ed7 8 buttons to
Ceiling
correct keystone distortion. (p.31)
Ceiling
When this function is set to “On,” the picture is top/bottom and
left/right reversed. This function is used to project the image
from a ceiling-mounted projector.
Rear
Rear
When this function is set to “On,” the picture is left/right
reversed. This function is used to project the image from the
rear of the screen.
Reset
This function returns all adjusted values to the factory default
settings. Press the SELECT button at Reset to display a
confirmation box. To reset, press the SELECT button at “Yes.”
Quit
Exit the Screen Size Adjustment Menu.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
Image Adjustment
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the Image Adjust Menu icon.
IMAGE ADjUST MENU
1
2
Use the Point ed buttons to move the red frame pointer
to the desired item and then press the SELECT button
to display the adjustment dialog box. Use the Point 7 8
Image Adjust Menu icon
buttons to adjust the setting value.
Move the red frame pointer to the desired
item and then press SELECT button.
Contrast
Press the Point 7 button to decrease contrast; press the Point
8 button to increase the contrast (from 0 to 63).
Brightness
Press the Point 7 button to decrease the brightness; press the
Point 8 button to increase the brightness (from 0 to 63).
✽
Color
Press the Point 7 button to decrease the intensity of the color;
press the Point 8 button to increase the intensity of the color
(from 0 to 63).
✽
Tint
Press the Point 7 8 buttons to adjust the tint value to obtain
proper color balance (from 0 to 63).
Color Management
The Color Management function can be used to adjust the
LEVEL, PHASE, and GAMMA of the selected display colors
(except for black, white, and gray) on the screen and replace
these colors with other colors if required.
Use the Point 7 8 buttons to adjust the
setting value.
You can store up to eight (8) color management data.
Use the Point ed buttons to move the red frame pointer
to Color Management, and then press the SELECT
button. The projected image freezes, and the COLOR
MANAGEMENT POINTER appears.
1
POINTER MODE
Use the Point ed7 8 buttons to move the pointer to the
spot where you want to adjust the color and then press
the SELECT button. The COLOR SELECTION window
appears, and the color in the center of the pointer is
selected and you can adjust the color.
2
COLOR MANAGEMENT
POINTER
Use the Point ed7 8 buttons to adjust the LEVEL and
PHASE of the color, and then press the SELECT button
to confirm the setting. Then use the Point ed buttons to
adjust the GAMMA for the color and press the SELECT
button to accept the setting. After adjusting, press the
SELECT button to go to the COLOR MANAGEMENT LIST.
3
✔Note:
✽ Displayed in grayout in the computer Input.
•Tint cannot be selected when the video
system is PAL, SECAM, PAL-M, or PAL-N
(p.42).
•Color management is displayed in grayout
when there is no signal.
COLOR SELECTION MODE
LIST
Go to the COLOR MANAGEMENT LIST.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
COLOR SELECTION MODE (continued)
COLOR SELECTION MODE
COLOR M
Level and phase
adjustment palette.
Gamma
adjustment palette.
Return to the COLOR MANAGEMENT POINTER. (If you
press the MENU button on the side control or the remote
control, it returns to the COLOR MANAGEMENT POINTER
and you will need to reselect and readjust the color.)
MENU
Return to the IMAGE ADJUST Menu. Any settings that
have been changed will not be stored. To store the
changed settings, be sure to select “LIST” and go to the
COLOR MANAGEMENT LIST.
In the COLOR MANAGEMENT LIST, the adjusted color
data are checkmarked. You can decide whether or not to
apply the adjusted color data in the list to the projected
image (see below).
4
LIST
COLOR M
MENU
LIST MODE
LIST MODE
Clear the check mark if you do not want to apply the
adjusted color data; select the check mark and then press
the SELECT button. The check mark disappears.
COLOR PALETTE
DEL
COLOR PALETTE
Return to the COLOR SELECTION mode so that you can
readjust the setting for the color in that line. (This option is
not available if the check mark is cleared.)
DEL
Select the DEL box if you want to delete the adjusted
data. Press the SELECT button and a confirmation box
appears and then select [Yes].
ALL DEL
Delete all the data in the list. Press the SELECT button and
a confirmation box appears and then select [Yes].
MENU
The same function as stated above.
ALL DEL
MENU
COLOR M
COLOR M
The same function as stated above.
Auto picture control
Use the Point 7 8 buttons to select the desired Auto picture
control position (Off, L1 or L2).
Off . . . . Auto picture control OFF position.
L1 . . . . . Auto picture control LEVEL 1 position.
L2 . . . . . Auto picture control LEVEL 2 position.
BrilliantColor
✔Note:
•
will be displayed in grayout when
‘Dynamic‘ is selected in the Image level
selection (pp.39, 43).
Color temp.
BrilliantColor extends the exposure range and sharpens detail
for grain free images. Use the Point 7 8 buttons to select from
(Off/On).
Color temp
Use the Point 7 8 buttons to select the desired Color temp.
level (XLow, Low, Mid, or High).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
White balance (Red/Green/Blue)
Press the Point 7 button to lighten red/green/blue tone; press the
Point 8 button to deepen red/green/blue tone (from 0 to 63).
Offset (Red/Green/Blue)
Press the Point 7 button to lighten red/green/blue tone of the
black level of an image; press the Point 8 button to deepen red/
green/blue tone of the black level of an image (from 0 to 63).
Sharpness
Press the SELECT button at this icon to
display other items.
Press the Point 7 button to decrease the sharpness of the image;
press the Point 8 button to increase the sharpness of the image
(from 0 to 31).
Gamma
Use the Point 7 8 buttons to adjust the gamma value to obtain a
better balance of contrast (from 0 to 15).
Press the SELECT button at this
icon to display the previous items.
✽
Noise reduction
Noise interference on the screen can be reduced. Press the Point
7 8 buttons to change the noise reduction mode.
Off . . . . Noise reduction mode is “Off”
On . . . . Noise reduction mode is “On”
Press the Point 7 8 buttons to
adjust the setting value.
✽
Progressive
An interlaced video signal can be displayed in progressive mode.
Press the Point 7 8 buttons to change the progressive scan mode.
Off . . . . Progressive scan mode is “Off.”
On . . . . Progressive scan mode is “On.”
Film . . . For watching a film. With this function, the projector
reproduces pictures faithful to the original film quality.
✔Note:
•Picture is distorted at the moment of On/Off /Film switching.
Reset
To reset the adjusted data, select Reset and press the SELECT
button. A confirmation box appears and then select [Yes]. All
adjustments will return to their previous figures.
Store
Image Level Menu
Move the red frame pointer
to an image item to be set
and then press the SELECT
button.
To store the adjusted data, move the red frame pointer to the
Store icon and press the SELECT button. The Image Level Menu
appears. Move the red arrow pointer to any of the Image 1 to
10 in which you want to set and press the SELECT button. A
confirmation box appears and then select [Yes].
Store icon
Press the SELECT button at this
icon to store the adjustment.
Quit
✔Note:
Exit the Image Adjust Menu.
✽ Displayed in grayout in the computer Input.
•When the Color matching function is set to ‘On’ and
the White balance Red, Green, or Blue is adjusted,
the Color temp. level will change to “Adj.”
•Progressive cannot be selected when “480p,” “575p,”
“720p”, or “1080p” is selected (p.42).
•Noise reduction cannot be selected with the
computer input and when the video signal format is
1080p.
4ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Setting
This projector has a Setting menu that allows you to set up other various functions.
Press the MENU button to display the On-Screen Menu.
Use the Point 7 8 buttons to move the red frame pointer
to the Setting Menu icon.
1
SETTING MENU (Language)
Use the Point ed buttons to move the red frame pointer
2
to the desired item and then press the
The Setting dialog box appears.
SELECT button.
Setting Menu icon
Set the red frame pointer
to the item and press the
SELECT button.
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean, or Japanese.
Menu
This function allows you to adjust the position and size of the
On-Screen Display and the value adjustment bar in the Picture
Image Adjustment Menu.
Position
Press the SELECT button at
Language, then the Language
Menu appears.
This function is used to adjust the On-Screen Menu display
position. Press the SELECT button and the adjustment
screen appears (arrows appear). Use the Point ed7 8
buttons to adjust the position. After making the adjustment,
press the SELECT button to return to the Menu screen.
Simple menu
When this function is set to “On,” the value adjustment bar in
the Picture Image Adjustment Menu appears on the screen.
Menu size
You can enlarge the size of On-Screen display to two times
the normal size. Use the Point 7 8 buttons to select from
(Normal/Double).
Display
This function decides whether to display On-Screen Displays.
On . . . . . . . . . . . . Show all the On-Screen Displays. Use this
function when you want to project images
after the lamp becomes bright enough. The
factory default setting is in this option.
Countdown Off. . . Show the input image instead of the
countdown when turning on the projector.
Use this function when you want to project
the image as early as possible even when
the lamp is not bright enough.
Menu
Off . . . . . . . . . . . . Hide the On-Screen Displays except:
l On-Screen Menu
l “Power off?” (p.25)
l Color management operation screen
(pp.46-47)
l “No signal” for Power management (p.57)
l P-TIMER (p.31)
l ”Please wait....” for Auto PC adjustment
(p.36)
Set the red frame pointer
to the item and press the
SELECT button.
l Arrows for panning mode
l Warnings for lens and color wheel
installations.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Background
The selected background screen will be displayed when no
input signal is detected.
Blue . . . Blue colored background.
User . . . The image you captured.
Black. . . Black colored background.
✔Note:
•“User” cannot be selected when the image is not
captured.
Lamp mode
✔Note:
This projector is equipped with 2 projection lamps and the
number of using lamps can be switched to 2 lamps or 1 lamp.
Using 1 lamp maintains the life of projection lamps.
• When switching from one of lamps to the other
(e.g. when switching from Lamp1 to Lamp2), both
lamps will light until the brightness of the lamps
are stabilized.
• When neither of the two lamps is lighted, the
projector will shutdown automatically.
• When either of the two lamps does not light up,
the LAMP 1/2 REPLACE indicator blinks orange
and the projector will light the other automatically.
(X mark will appear on the unlighted lamp in the
Lamp Status Display. See page 65 for details.)
Press the SELECT button at Lamp mode to display a dialog
box. Use the Point ed buttons to select "2-Lamps", "Lamp1" or
"Lamp2" and press the SELECT button. Then the confirmation
message appears. Select [Yes] and press the SELECT button.
2-Lamps . . Two lamps turn on.
Lamp1 . . . Only Lamp1 turns on.
Lamp2 . . . Only Lamp2 turns on.
Lamp control
Lamp control
✔Note:
This function allows you to change brightness of the screen.
•The fan noise becomes louder in Eco 2 than in
Eco 1. Select the suitable mode for the used
environment.
Normal . . . Normal brightness.
Eco 1. . . . . Lower brightness and Fan speed decrease.
Lower brightness reduces the lamp power
consumption and extends the lamp life.
Eco 2. . . . . Lower brightness and Fan speed increase.
Lower brightness reduces the lamp power
consumption and extends the lamp life. It is
recommended to use Eco 2 when using the
projector continuously over a long period of
time.
✔Note:
• If Mode 2 has been selected and either of two
lamps exceeded its recommended total hours
of use, Lamp interval mode will be fixed to ‘Off’.
Also, ‘2-Lamps’ icon in the Lamp mode and the
icon of lamp which exceeded its recommended
total hours of use will be displayed in grayout.
• If Mode 2 has been selected and both lamps
exceeded the recommended total hours of use,
the warning icon will be displayed at the time of
power-on. Then the projector will turn off after 3
minutes.
Lamp life control
Select the lamp operation when the total lighting time of a
lamp exceeds the recommended total hours of use.
Mode 1 . . . A lamp can be turned on even after exceeding
the recommended total hours of use.
Mode 2 . . . A lamp is not turned on after exceeding the
recommended total hours of use.
Lamp interval
✔Note:
• When either of the two lamps is out, the projector
will light the other automatically even if 'Off' is
selected.
• When ‘AUTO’ is selected, the projector
automatically detects which lamp is used less
often than the other at the time of power-on and
lights it.
This function can be used to automatically switch the lamp
that is turned on after a certain period of time in order to
reduce the lamp deterioration when 'Lamp1' or 'Lamp2' has
been selected in 'Lamp mode' setting.
Use the Point 7 8 buttons to select from (Off/Auto/24h/200h/
500h/1000h/2000h).
•The setting values of time interval may not be
accurate, and should be used only as a guide.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Picture in Picture
Picture in Picture
Status (Stored /Free/
Selected Mode
This function is used to project two videos simultaneously
by placing a separate small sub screen within the main
screen.
Adj.) of the selected
mode.
Use the Point ed buttons to move the red frame pointer
to Picture in Picture and then press the SELECT button to
display a dialog box. Use the Point 7 8 buttons to adjust the
setting value.
Use the Point 7 8
buttons to adjust
the setting value.
Picture in Picture . . .Show the selected mode (Off/User1-5)
and its status (Stored /Free/Adj.).
Mode. . . . . . P in P: Provide the images of Main picture
and Sub picture at the ratio of 16:9.
P by P: Provide the images of Main picture
and Sub picture at the ratio of 4:3.
Main picture/
Sub picture .. Input:
Select an input from Input 1-4.
Source: Select an input source. The display
varies depending on the selected
input.
Size:
Select the display size. Main picture
can be changed between 10 and
100%, and Sub picture can be
changed between 10 to 50% in
increments of 10%. When P by P
is selected in Mode, the projection
size is fixed to 50%.
Active
frame
(White)
Position: Press the SELECT button at
Position and the display position
Center line
display
setting screen appears. Use the
Point ed7 8 buttons to adjust
the display position of active frame
indicated in white. The frame will
disappear after 10 seconds or when
the SELECT button is pressed.
Frame Lock . . . Set the Frame Lock to Main picture or Sub
picture.
To store the adjusted data
This mode
has stored
data.
Reset. . . . . . . . Press the SELECT button at Reset to
display a confirmation box. To reset, press
the SELECT button at [Yes].
Vacant
Mode free . . . . Delete the data stored in the Mode and
return to the ‘Free‘ state. Use the Point 7
8 buttons to select Mode free and press
the SELECT button to show the 'Where
to free?' dialog box. Move the red arrow
pointer to one of the mode (Mode 1 - 5)
which you want to delete and press the
SELECT button. Then the Confirmation box
appears. To delete, select [Yes].
Close this dialog box.
Confirmation box appears
and then select [Yes].
Store . . . . . . . . Store the adjusted data in the User 1–5.
Use the Point 7 8 buttons to select Store
and press the SELECT button to show the
‘Where to store?‘ dialog box. Move the red
arrow pointer to one of the mode (Mode 1
- 5) in which you want to store and press
the SELECT button. Then the Confirmation
box appears. To store adjusted data, select
[Yes].
✔Note:
•The Picture in Picture function is not available depending
on the input signals and the selected input terminals. Refer
to ‘List of Picture in Picture‘ for details. (p.82)
• When the input signal(s) is/are incompatible, X mark will
be displayed on the Main/Sub picture.
• While the Main and Sub pictures are being displayed,
System, Image select, Image adj. and Screen menus
(except for ‘Keystone’, ‘Ceiling’ and ‘Rear’) are inoperative.
Quit . . . . . . . . . Exit the Picture in Picture menu.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Edge blending
This function allows multiple projector images to be seamlessly
overlapped.
Edge blending
Use the Point ed buttons to move the red frame pointer to
Edge blending and then press the SELECT button to display a
dialog box. Use the Point ed7 8 buttons to adjust the setting
value.
Edge blending . . Set to ‘On‘ to activate the Edge blending
function.
Width. . . . . . . . . Adjust the width of correction.
Right/Left: Set the width. (from 0 to 960).
Top/Bottom: Set the width. (from 0 to 540).
Black level . . . . . Adjust the black level of projected image.
All:
The values of R, G, and B will be
changed simultaneously.
R/G/B: Adjust the value ( 127).
Test pattern . . . . Select ‘On‘ to display a suitable pattern.
Reset. . . . . . . . . Select ‘Reset’ and press the SELECT button.
Then ‘Return to factory default of Edge
Close this dialog box.
Blending?‘ message appears. To reset, press
the SELECT button at [Yes].
Quit . . . . . . . . . . Exit the Edge blending menu.
Color matching
When multiple sets are used simultaneously, this projector
allows the user to correct the difference of colors among the sets.
Color matching
Use the Point ed buttons to move the red frame pointer to
Color matching and then press the SELECT button to display a
dialog box. Use the Point ed7 8 buttons to adjust the setting
value.
Color matching . . . .Set to ‘On‘ to activate the Color matching
function. When the color matching is set
to ‘Off‘, all items except for Advanced
color matching are displayed in grayout
and cannot be adjusted.
Color adjustment. . .Adjust the color setting of Red/Green/
Blue/White. The chromatic coordinate
(X,Y) of Red, Green, Blue, and White can
be adjusted respectively. The adjustable
range is from 0.000 to 1.000.
Close this dialog box.
Auto test pattern . . .Select ‘On‘ to display a suitable pattern
when setting items.
Reset. . . . . . . . . . . .Select ‘Reset’ and press the SELECT
button. Then the confirmation message
appears. Press the SELECT button at [Yes]
to reset to the previously stored values.
Store . . . . . . . . . . . .Select ‘Store’ and press the SELECT
button to display the Confirmation box. To
store adjusted data, select [Yes].
Advanced
color matching . . . . .Select ‘Advanced color matching’ and
press the SELECT button for more
detailed settings. Another setting screen
will appear.
5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Advanced
color matching. . . . .Set to ‘On‘ to activate the ‘Advanced color
matching’. When it is set to ‘Off‘, all items
except for ’Test pattern’ are displayed in
grayout and cannot be adjusted.
Advanced color matching
Measured . . . . . . . .When using the color wheel set optimized
for high brightness, the chromatic
coordinate (X,Y) and the brightness (L) of
Red, Green, Blue, Half white, and White
are displayed. When using the color wheel
set optimized for rich color reproduction,
the chromatic coordinate (X,Y) and the
brightness (L) of Red, Green, Blue, and
White are displayed.
Target . . . . . . . . . . .Adjust the chromatic coordinate (X,Y) and
the gain value (g) of Red, Green, Blue,
Cyan, Magenta, Yellow, and White. Use
the Point ed7 8 buttons to move the
red frame pointer to an item of which you
want to adjust the value and then press
the SELECT button. Use the Point ed
buttons to adjust the value. To move to
the next digit, use the Point 7 8 buttons.
Press the SELECT button to set the value.
Auto test pattern . . .Select ‘On‘ to display a suitable pattern
when setting items.
Close this dialog box.
Reset. . . . . . . . . . . .Select ‘Reset’ and press the SELECT
button. Then the confirmation message
appears. Press the SELECT button at [Yes]
to reset to the previously stored values.
Store . . . . . . . . . . . .Select ‘Store’ and press the SELECT
button. Then the Confirmation box
appears. To store adjusted data, select
[Yes].
Test pattern . . . . . . .When using the color wheel set optimized
for high brightness, use the Point ed
buttons to select from (Measured) Red/
Green/Blue/Half white/White/(Target) Red/
Green/Blue/ Cyan/Magenta/Yellow/White.
When using the color wheel set optimized
for rich color reproduction, use the Point
ed buttons to select from (Measured)
Red/Green/Blue/White/(Target) Red/
Green/Blue/Cyan/Magenta/Yellow/White.
Quit . . . . . . . . . . . . .Exit the Color matching menu.
DynamicBlack
DynamicBlackTM improves the black level of the projector. Black
level is the darkest part of a picture and varies between viewing
devices and environments. Set DynamicBlack Off/Low/High.
5ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
HDMI setup
HDMI setup
Select Normal or Enhanced according to the output signal
of video equipment. Press the Point 7 8 buttons to switch
between each option.
Normal . . . . When the output of video equipment is set to
“STANDARD.”
Enhanced . . When the output of video equipment is set to
“ENHANCED.”
The names for the output setting of video equipment vary
from equipment to equipment. For details, refer to the owner’s
manual of video equipment.
Press the Point 7 8 buttons
to select Normal or Enhanced
according to the output signal of
video equipment.
When the black parts of the image are destroyed or stand out,
please switch to "Normal" or "Enhanced", and then switch the
output type of the HDMI video output equipment.
Logo
Logo
This function allows you to customize the screen logo with Logo
select, Capture, and Logo PIN code lock functions.
Logo select
This function decides on the starting-up display from
among the following options.
Off . . . . Show the countdown display only.
Default . Show the factory-set logo.
User . . . Show the image you captured.
Capture
Set the red frame pointer
to the item and press the
SELECT button.
This function enables you to capture an image being
projected to use it for a starting-up display or interval of
presentations.
✔Note:
Select Capture and press the SELECT button.
A confirmation box appears and select [Yes] to capture the
projected image.
•When “On” is selected in the Logo PIN code lock function,
Logo select and Capture functions cannot be selected.
After capturing the projected image, go to the Logo select
function and set it to “User”. Then the captured image will
be displayed the next time you turn on the projector.
Capture
To cancel the Capture function, select [No].
✔Note:
Set the pointer (red
arrow) to the item and
press the SELECT button.
•Before capturing an image, select “Standard” in the Image
Select Menu to capture a proper image. (pp.39, 43)
•A signal from a computer can be captured up to 1920 x
1080 dots.
•Certain signals may not be captured properly.
•When capturing the image that has been adjusted by the
Keystone function, the adjusted data is automatically reset
and the projector captures an image without keystone
correction.
Select [Yes]
to capture
the projected
image.
•When starting to capture a new image, the previously
stored image is cleared even if you cancel the capturing.
•Once you exit the Logo Menu after setting the Logo lock
to "On," you are required to enter the PIN code every
attempting to change the Logo setting.
Select [Yes] to stop
capturing.
•“User” cannot be selected when the image is not
captured.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo PIN Code Lock
Logo PIN code lock
This function prevents an unauthorized person from changing
the screen logo.
Off . . . . The screen logo can be changed freely from the
Logo Menu.
On . . . . The screen logo cannot be changed without a
Logo PIN code.
If you want to change the Logo PIN code lock setting, press
the SELECT button and the Logo PIN code dialog box appears.
Enter a Logo PIN code by following the steps below. The initial
Logo PIN code is set to “4321” at the factory.
Enter a Logo PIN code
Enter a Logo PIN code
Use the Point ed buttons on the side control or on
the remote control to enter a number. Press the Point
8 button to fix the number and move the red frame
pointer to the next box. The number changes to “✳.”
Repeat this step to complete entering a four-digit
number. After entering the four-digit number, move the
pointer to “Set.” Press the SELECT button so that you
can change the Logo PIN code lock setting.
After a correct Logo PIN code is
entered, the following dialog box
appears.
Change the Logo PIN code lock setting
If you fixed an incorrect number, use the Point 7 button
to move the pointer to the number you want to correct,
and then enter the correct number.
Use the Point 7 8 buttons to switch On/Off,
If you entered an incorrect Logo PIN code, “Logo
PIN code” and the number (✳✳✳✳) will turn red for a
moment. Enter the correct PIN code all over again.
Change the Logo PIN code
Change the Logo PIN code lock setting
Use the Point 7 8 buttons to switch On/Off, and then press
the Point d button to move the pointer to “Quit.” Press the
SELECT button to close the dialog box.
Change the Logo PIN code
CAUTION:
Logo PIN code can be changed to your desired four-digit
number. Press the Point d button to select “Logo PIN code
change” and then press the SELECT button. The New Logo
PIN code input dialog box appears. Set a new Logo PIN code.
WHENyOU HAVE CHANGEDTHE LOGO PIN
CODE,WRITE DOWNTHE NEW PIN CODE
IN COLUMN OFTHE LOGO PIN CODE NO
MEMO ON PAGE ꢂ6, AND KEEP IT SECURELy
SHOULDTHE LOGO PIN CODE BE LOST OR
FORGOTTEN,THE LOGO PIN CODE SETTING
CAN NO LONGER BE CHANGED
Be sure to note the new Logo PIN code and keep it on hand.
If you lost the number, you could no longer change the Logo
PIN code setting. For details on PIN code setting, refer to “PIN
code lock” on pages 58–59.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Filter control
✔Note:
You can replace the filter with this function. Press the SELECT
button at Filter control to display a confirmation box. To replace,
press the SELECT button at “YES” and the electrically operated
filter starts to scroll.
•Filter replacement icon and “Please wait...”
message appear on the screen when the filter is
being scrolled.
•The filter cannot be rewound.
•When the filter is replaced, the total accumulated
time of the filter use is automatically set to 0.
You can also replace the filter by using the remote control
(p.31).
Fan control
Choose the running speed of cooling fans from the following
options.
Normal....... Normal speed.
Max ........... Faster than the normal speed.
Remote control
The eight different remote control codes (Code 1–Code 8) are
assigned to the projector; the factory-set, initial code (Code 1)
and the other seven codes (Code 2 to Code 8).
Remote control
The same code should be set on both the projector and the
remote control. For example, operating the projector in “Code
7”, the remote control code also must be switched to “Code 7”.
To change the code for the projector;
Select a remote control code in this Setting Menu.
To change the code for the remote control;
Check the Reset Switch to "Use position" in the compartment
lid on the back of the remote control.
And then while holding down the MENU button, press and
release the IMAGE ADJ. button the number of corresponding
times you would like to set the number of the remote control
code for the projector. (See page 16)
When pressing the SELECT button at
Remote control, the Remote control
code menu appears.
To reset the code for the remote control;
Slide the Reset Switch to "Reset position" in the compartment
lid on back of the remote control.
RC sensor
Select a location of the infrared remote receiver of the remote
control. See “Remote Control Receivers and Operating Range”
on page 15 for details.
All . . . . . . . . . . .Activate all of the front, top and back receivers.
Front &Top . . . .Activate the front and top receivers.
Top & Back . . . .Activate the top and back receivers.
Front & Back. . .Activate the front and back receivers.
Front . . . . . . . . .Activate only the front receiver.
Top . . . . . . . . . .Activate only the top receiver.
Back . . . . . . . . .Activate only the back receiver.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Power management
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not used for a certain
period.
Time left before the lamp is off
If the input signal is interrupted and no button is pressed for
more than 30 seconds, the timer display with “No signal”
appears. It starts the countdown until the lamp is turned off. The
countdown time can be set between 1 and 30 minutes.
Use the Point 7 8 buttons to set the countdown timer.
Press the SELECT button at Power
Select one of the following options:
management and the dialog box
appears. Use the Point 7 8 buttons
to choose one of the three options.
Press the Point d button to select
the timer, and then use the Point 7
8 buttons to set the timer.
Ready . . . . When the lamp has been fully cooled down,
the POWER indicator starts blinking. In this
condition, the projection lamp is turned on if the
input signal is reconnected or any button on the
side control or remote control is pressed .
Shutdown. . When the lamp has been fully cooled down, the
power is turned off.
Off . . . . . . . Power Management function is off.
✔Note:
•Factory default is “Ready: 5 min.”
•When the shutter is closed while the Power
management function is working, the Power
management function is released.
On start
When this function is set to “On,” the projector will be
automatically turned on just by connecting the AC power cord to
the wall outlet.
✔Note:
• Make sure that the MAIN ON / OFF switch is ON, otherwise the
On start function does not work.
• Be sure to turn off the projector properly (see “Turning Off the
Projector” on page 25). If the projector is turned off in the incorrect
sequence, the On start function does not work properly.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Security
Security
Key lock
This function locks the side control and remote control buttons
to prevent operation by unauthorized persons.
. . . . . Unlocked.
. . . . . Lock the side control buttons.
To unlock, use the remote control.
. . . . . Lock the remote control buttons.
To unlock, use the side control.
Set the red frame
pointer to the item
and press the
SELECT button.
Key lock
If the side control accidentally becomes locked and you
do not have the remote control nearby and unable to
operate the projector, contact the service station.
Select Key lock and
this box appears.
Choose one of the
alternatives with the
Point ed buttons
and select [Yes] to
activate it.
PIN code lock
This function prevents the projector from being operated
by unauthorized persons and provides the following setting
options for security.
Off . . . . Unlocked.
On1 . . . Enter the PIN code every time turning on the
projector.
PIN code lock
On2 . . . Enter the PIN code to operate the projector once
the Main On/Off Switch is pressed to Off or the
power cord is unplugged ; as long as the AC power
cord is connected and the Main On/Off Switch
is pressed to ON, the projector can be operated
without a PIN code.
Whenever you change the PIN code lock setting or the PIN
code (the four-digit number), you are required to enter the PIN
code. “1234” is set as the initial PIN code at the factory.
When the projector
is locked with a PIN
code, the PIN code
lock symbol appears
on the menu bar.
If you want to change the PIN code lock setting, press the
SELECT button and the PIN code dialog box appears. Enter a
PIN code by following the steps on the next page.
5ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Enter a PIN code
Enter a PIN code
Use the Point ed buttons on the side control or on
the remote control to enter a number. Press the Point
8 button to fix the number and move the red frame
pointer to the next box. The number changes to “✳.”
Repeat this step to complete entering a four-digit
number. After entering the four-digit number, move
the pointer to “Set.” Press the SELECT button so that
you can change the PIN code lock setting .
After a correct Logo PIN code is
entered, the following dialog box
appears.
If you fixed an incorrect number, use the Point 7
button to move the pointer to the number you want
to correct, and then enter the correct number.
Change the PIN code lock setting
Use the Point 7 8
buttons to switch
between the options.
If you entered an incorrect PIN code, “PIN code” and
the number (✳✳✳✳) will turn red for a moment. Enter
the correct PIN code all over again.
Change the PIN Code Lock setting
Use the Point 7 8 button to select Off, On1, or On2 and then
move the pointer to “Quit” with the Point d button. Press the
SELECT button to close the dialog box.
Change the PIN Code
The PIN code can be changed to your desired four-digit
number. Press the Point d buttons to select “PIN code
change” and press the SELECT button. The New PIN code
input dialog box appears. Set a new PIN code.
Change the PIN code
CAUTION:
WHENyOU HAVE CHANGEDTHE PIN CODE,WRITE
DOWN A NEW PIN CODE IN COLUMN OFTHE PIN CODE
NO MEMO ON PAGE ꢂ6, AND KEEP IT SECURELy IF
yOU FORGETyOUR PIN CODE,THE PROjECTOR CAN NO
LONGER BE STARTED
Projector ID
This feature allows users to set serial communication
configuration (Projector ID) when several projectors are
connected via the RS-232C terminal (serial port) of the
projector.
Use the Point 7 8 buttons to adjust the Projector ID.
l Projector ID ... 1 - 999. (Factory default setting : Projector ID 1)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Shutter
Shutter function is available to block out light to the
screen, so that the screen can be used for the other
presenters.
Protection
Prohibits the shutter operation from the remote control
and the projector's side control.
Remote control . . . Selecting "On" prohibits the shutter
operation from the remote control.
Projector . . . . . . . . Selecting "On" prohibits the shutter
operation from the side control.
It is possible to prohibit the shutter operation from both of
the remote control and the side control.
Management
The Shutter Management function turns off the projection
lamp when the projector is left with the shutter closed and
the set time has passed away. The count-down time can be
set between 5 and 180 minutes. When the count-down time
has elapsed, the shutter will be opened up automatically and
the lamp will be turned off to cool itself down. The SHUTTER
indicator is blinking blue during this cooling-off period. When
the lamp has been fully cooled down, the POWER indicator
turns green lighting and the SHUTTER indicator keeps
blinking. Should the ON / STAND-BY button be pressed in
this condition, the projection lamp will be turned on and the
SHUTTER indicator turns off.
✔Note:
•The Factory default value is set to 180
minutes for the count down time.
•The Shutter Management function cannot be
halted.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Filter counter
Filter counter
This function is used to set a time for the filter replacement.
Use the Point ed buttons to move the red frame pointer to Filter
counter and then press the SELECT button. A dialog box appears
showing the Used time option and the Scrolls remaining option.
Set the red frame pointer
to the item and press the
SELECT button.
UsedTime . . . . . . Show the total accumulated time of the
filter use, timer setting option and the Reset
options. When the projector reaches a time
set in the timer setting, the Filter replacement
icon (Fig. 1) appears on the screen and the
total accumulated time turns red, indicating
that the filter replacement is necessary. If
the filter is out of scroll and the projector
reaches a time set in the timer setting, Fig.
2 appears on the screen, indicating that the
Use the Point 7 8 buttons
to set the timer. Select from
(Off/1000H/2000H/3000H)
depending on the use
environment
Fig 1 Filter replacement icon
filter cartridge replacement is necessary.
Scrolls remaining . . Show the scroll counter and the Reset
options. When the filter scroll is counted
Filter replacement icon appears on the screen
at a set time.
down to 1 (Scroll counter on the screen is
showing “0 scroll(s)” , the last scroll icon
Fig ꢀ
(Fig. 3) appears on the screen. When the
filter scroll is counted down to 0, the Filter
cartridge replacement icon (Fig. 4) appears
on the screen and the WARNING FILTER
indicator lights orange, indicating that the
filter cartridge replacement is necessary.
Fig ꢁ Last scroll icon
Last scroll icon appears on the screen when
the filter is down to the last scroll.
To set a timer, press the SELECT button on Used time option.
Move the red arrow pointer to the timer setting option and use
the Point 7 8 buttons to select from (Off/1000H/2000H/3000H)
Fig 4 Filter cartridge replacement icon
Filter cartridge replacement icon appears on
the screen when the filter scroll is counted
down to 0 scroll.
depending on the use environment.
When replacing the Filter cartridge, reset the Filter counter and the
Scroll counter (p.64).
✔Note:
•Fig.1, Fig. 2, Fig. 3 or Fig. 4 will appear at turning on
and selecting input source.
✔Note:
•Do not reset the Filter counter and the Scroll counter
without replacing the Filter cartridge. Be sure to reset the
Filter counter and the Scroll counter only after replacing
the Filter cartridge.
•Fig.1, Fig. 2, Fig. 3 or Fig. 4 will not appear
when the Display function is set to “Off” (p.49),
or during “Freeze” (p.30).
Factory default
•Timer setting notifies that the filter needs replacement. To
replace the filter, use the filter control function (p.56).
Set the red frame pointer
to the item and press the
SELECT button.
Test pattern
Various test patterns are available for use when setting up the
projector.
Select Factory default and this box
appears. Select [Yes], and the next
box appears.
Factory default
This function returns all setting values except for the user logo,
PIN code lock, Logo PIN code lock, lamp counter, filter counter
and filter timer to the factory default settings.
Quit
Select [Yes] to
activate it.
Exit the Setting Menu.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter becomes
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup
and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to
replace the filter easily. The projector monitors the condition of the filter at all time and replaces a filter with a
new one automatically when it detects the clogging.
If the projector reaches a time set in the timer setting (p.61),
a Filter replacement icon (Fig.1) appears on the screen and
the WARNING FILTER indicator on the top panel lights up
(p.79). When you see this icon, replace the filter as soon
as possible (pp.31, 56). If the filter is out of scroll and the
projector reaches a time set in the timer setting, Fig. 2
appears on the screen, indicating that the filter cartridge
replacement is necessary.
Fig 1 Filter replacement icon
When the filter scroll is counted down to 1, the Last scroll
icon (Fig.3) appears on the screen, indicating that there is
one scroll left in the filter cartridge (p.61).
Fig ꢀ
If the projector detects that the filter is clogged and no scroll
is left in the filter cartridge, a Filter cartridge replacement
icon (Fig. 4) appears on the screen and the WARNING
Fig ꢁ Last scroll icon
FILTER indicator on the top panel lights up (p.79). When you
see this icon, replace the filter cartridge (p.63) and reset the
Filter counter (p.64) and the Scroll counter (p.64).
When the filter is being scrolled by the remote control (p.31)
Fig 4 Filter cartridge replacement icon
or the Filter control function in the setting menu (p.56), a
Filter replacement icon and “Please wait...” message (Fig.5)
appear on the screen and the WARNING FILTER indicator
blinks slow (approx. 2 seconds ON, 2 seconds OFF) (p.77).
Fig 5 Filter replacement icon and
The WARNING FILTER indicator blinks fast when the
projector detects an abnormal condition, the filter cartridge
is not installed properly, or the filter scroll is not working
properly (p.79).
“Please wait...” message.
✔Note:
•Do not use the filter cartridge with other projector. The filter
counter and the scroll counter do not recognize the correct
number of remaining scrolls of the used filter cartridge and the
reset function cannot work properly. It may cause a breakdown.
•Make sure that the projection lamps are turned off when you
are replacing the filter cartridge. If you replace the filter cartridge
when the projection lamps are turned on, the projector will be
shut down automatically for safety purposes.
•Do not forget to reset the filter counter and the scroll counter in
the setting menu after replacing the filter cartridge. If you forget
to reset the filter counter and the scroll counter, the projector
cannot recognize the correct number of remaining scrolls and it
may cause a breakdown.
•Fig.1, Fig.2, Fig.3 or Fig. 4 will not appear when the Display
function is set to “Off” (p.49), or during “Freeze” (p.30).
•The filter cannot be rewound.
•The filter can be scrolled 9 times since the filter cartridge has
10 scrolls.
•The filter cartridge is disposable. Do not clean and reuse the
filter cartridge.
•Do not expose the filter cartridge to water or liquid, or it may
cause a breakdown.
•Replace the filter cartridge after all the scroll is used up. If you
replace the filter cartridge when there are some scrolls left in
the filter cartridge, the filter counter and the scroll counter do
not recognize the correct number of remaining scrolls and the
reset function cannot work properly. It may cause a breakdown.
•The used part of the filter can be seen on the edge of the Filter
cartridge after scrolling the filter, but there is no problem for the
use of the projector.
•When the projector is kept used for 3 minutes without getting
the filter cartridge replaced after the Fig.4 appears on the screen,
the projector is turned off automatically to prevent the damage of
optical components.
6ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Replacing the Filter Cartridge
Turn off the projector, press the Main On/Off Switch to
Off and unplug the AC power cord from the AC outlet.
1
Filter cover
First, clean up the dust on the projector and around the
air vents.
2
Open the filter cover. (See the right figure.)
3
Pull out the filter cartridge. When taking out
the filter cartridge, put your finger on the filter
cartridge’s tab and then pull.
4
Put the new one back into the position and close
the filter cover. Make sure that the filter cartridge is
properly and fully inserted.
5
Filter cartridge
Connect the AC power cord to the projector and turn
6
on the projector.
Reset the filter counter and the scroll counter (p.64).
7
CAUTION
Make sure the filter cartridge is inserted in the
projector. If the filter cartridge is not inserted, the
projector cannot be turned on.
Do not put anything into the air vents. Doing so
may result in malfunction of the projector.
Tab
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
operating the projector Usage in these environments may
cause a poor image quality
When using the projector under dusty or smoky conditions, dust
may accumulate on a lens or optical elements inside the projector.
Such condition may degrade the quality of the projected image.
When the symptoms above are noticed, contact your authorized
dealer or service station for proper cleaning.
ORDER REPLACEMENT FILTER CARTRIDGE
Replacement filter cartridge can be ordered through your
dealer. When ordering, give the following information to the
dealer.
l Model No of your projector
PDG-DHT100L
l Replacement Filter Cartridge
Type No : POA-FIL-1ꢁ1
(Service Parts Code: 610 ꢁꢁ4 ꢁ747)
6ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Resetting the Filter Counter
Filter counter
Be sure to reset the Filter counter after replacing the filter
cartridge.
Press the MENU button to display the On-Screen Menu. Use
the Point 7 8 buttons to move the red frame pointer to the
Setting Menu icon.
1
Use the Point ed buttons to move the red frame pointer to
Filter counter and then press the SELECT button.
A dialog box appears showing the Used time option and the
2
Select “Used time” and the
dialogue box below appears.
Scrolls remaining option. Use the Point ed buttons to select
Used time.
Used time shows the total accumulated time of the filter
use, a timer setting option, and the Reset option. Select
Reset and the “Filter counter Reset?” appears. Select [Yes]
to continue.
3
Select Reset and the “Filter
counter Reset?” appears.
Another confirmation dialog box appears, select [Yes] to
4
reset the Filter counter.
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Filter counter.
Resetting the Scroll Counter
Scroll counter
Be sure to reset the Scroll counter after replacing the filter
cartridge.
Press the MENU button to display the On-Screen Menu. Use
the Point 7 8 buttons to move the red frame pointer to the
Setting Menu icon.
1
Use the Point ed buttons to move the red frame pointer to
Filter counter and then press the SELECT button. A dialog
box appears showing the Used time option and the Scrolls
2
Select “Scrolls remaining” and
the dialogue box below appears.
remaining option. Use the Point ed buttons to select
Scroll(s) remaining.
Scroll(s) remaining shows the number of the remaining
scrolls and the Reset option. Select Reset and the “Scroll
counter Reset?” appears. Select [Yes] to continue.
3
Select Reset and the “Scroll
counter Reset?” appears.
Another confirmation dialog box appears, select [Yes] to
4
reset the Scroll counter.
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Scroll counter.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Lamp Management
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled by
the Lamp Management Function. The Lamp Management Function detects the status of lamps and shows the
status on screen or on the LAMP 1/2 REPLACE indicators. This function also automatically controls the Lamp
Mode when any of lamps is out for the end of life or malfunctions.
LAMP 1/2 REPLACE
INDICATORS
Lamp status
Lamp 1/ꢀ Replace Indicators
The LAMP 1/2 REPLACE indicators light orange when any of Projection Lamps is nearing its end, and flash
when any of them becomes out. Check the number of lamp on the Lamp Status Display or the LAMP 1/2
REPLACE indicators and replace the lamp.
Lamp Status Display
The Lamp Status Display appears on screen when the projector is turned on or the input position (input 1, input
2, Input 3 or input 4) is switched. This shows the status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to
the following for each status.
yellow Lamp
Dim Lamp
Red Lamp
Projection Lamp lights normally.
Projection Lamp is turned off.
Projection Lamp is nearing its end. When the image
becomes darker or the color becomes unnatural,
replace lamp. (LAMP 1/2 REPLACE indicator lights
orange.)
LAMP STATUS
DISPLAY
X Mark on Lamp
(LAMP 1/2 REPLACE indicator flashes orange.)
Projection lamp is defective or fails to be turned on.
Restart the projector on, and make sure lamp is on.
If this mark still appears, replace lamp corresponding
with number marked X.
Lamp Mode Changeover
The Lamp Management Function automatically changes the lighting lamp (Lamp Mode) by detecting the status of lamp.
When either of the 2 lamps is out, the projector operates with 1 lamp. The Lamp Mode can be switched to 2 lamps or 1
lamp manually. Refer to the SETTING section on page 50.
When Lamp 1 is burnt out.
1 LAMP MODE
2 LAMP MODE
When Lamp 2 is burnt out.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Lamp Replacement
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the
screen and LAMP 1/2 REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing
when the LAMP 1/2 REPLACE indicators should light is depending on the lamp mode.
Indicators
WARNING:
TURN OFFTHE UV LAMP BEFORE
OPENINGTHE LAMP COVER.
Lamp replacement icon
Allow the projector to cool, for at least 45 minutes
before you open Lamp Cover. The inside of the
projector can become very hot.
LAMP 1 / ꢀ REPLACE indicators
CAUTION
✔Note:
For continued safety, replace with a lamp assembly
•The Lamp replacement icon will not appear
of the same type.
when the Display function is set to “Off” (p.49),
or during “Freeze” (p.30).
Do not drop the lamp assembly or touch a glass
bulb!The glass can shatter and may cause injury.
Follow these steps to replace the lamp.
Check the number of lamp to be replaced on the Lamp
Status Display.
1
Turn off the projector, press the Main On/Off Switch to Off
and unplug the AC power cord from the AC outlet. Let the
projector cool for at least 45 minutes.
2
SCREW
Loosen a screw on the Lamp Cover. Slide and open the
Lamp Cover until it makes a clicking sound. (See the right
figure.)
LAMP
COVER
3
4
Loosen two screws and pull out the Lamp to be replaced
by grasping handle.
LAMP 1
Replace the Lamp with a new one and tighten two
screws. Make sure the Lamp is set properly.
5
6
Put the Lamp Cover back and tighten a screw.
SCREWS
LAMP 2
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.
CAUTION : DO NOT OPERATETHE PROjECTORWHILE ANy OF LAMPS IS REMOVED IT MAy RESULT IN
MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we
recommend replacing both ꢀ lamps at a time
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following
information to the dealer.
l Model No of your projector
:
:
PDG-DHT100L
l Replacement LampType No
POA-LMP1ꢁ0
(Service Parts No. 610 343 5336)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
l Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
l If the projector indicates that the lamp should be replaced, i.e., if the LAMP 1/2 REPLACE indicators
light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp
with the LAMP 1/2 REPLACE indicators lighted may increase the risk of lamp explosion.
l Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES,THE FOLLOWING SAFETy PRECAUTIONS SHOULD BETAKEN
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Optional ColorWheel Installation
The projector comes with the high brightness color
wheels installed. Additional rich color reproduction
color wheels are supplied. To replace the color wheels,
refer to the following steps.
SCREW
Turn off the projector, press the Main On/Off Switch to Off
and unplug the AC power cord from the AC outlet. Let the
projector cool for at least 45 minutes.
1
LAMP
COVER
Loosen a screw on the Lamp Cover. Slide and open the
Lamp Cover until it makes a clicking sound. (See the right
figure.)
2
COLOR WHEELS
Loosen three screws and pull out the color wheel to be
replaced by grasping handle.
3
Replace the color wheel with a new one and tighten three
screws. Make sure the color wheels are set properly.
4
Put the Lamp Cover back and tighten a screw.
5
✔Note:
SCREWS
•
•
Wait until the lamp house and the color wheel cool off.
Make sure to install the same type of two color wheels at
the same time. When different types of color wheels are
installed, ‘Non-matching color wheels!‘ message appears
on the screen.
Allow the projector to cool, for at least 45 minutes
before you open Lamp Cover. The inside of the
projector can become very hot.
6ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Cleaning the Projection Lens
Turn off the projector, press the Main On/Off Switch to Off
and unplug the AC power cord from the AC outlet before
cleaning.
Gently wipe the projection lens with a cleaning cloth that
contains a small amount of non-abrasive camera lens
cleaner, or use a lens cleaning paper or commercially
available air blower to clean the lens.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the lens.
Cleaning the Projector Cabinet
Turn off the projector, press the Main On/Off Switch to Off
and unplug the AC power cord from the AC outlet before
cleaning.
Gently wipe the projector body with a soft dry cleaning
cloth. When the cabinet is heavily soiled, use a small amount
of mild detergent and finish with a soft dry cleaning cloth.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the cabinet.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Warning Indicators
The WARNING indicators show the state of the function which protects the projector. Check the state of the
WARNINGTEMP. indicator and the LAMP indicator to take proper maintenance.
The projector is shut down and the WARNING TEMP.
indicator is blinking red.
Indicators
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down
to protect the inside of the projector. The LAMP indicator
turns red brighter and the WARNINGTEMP indicator
blinks while the projector is being cooled down. When the
projector has cooled down enough (to its normal operating
temperature), it can be turned on again by pressing the ON/
STAND-BY button.
✔Note:
WARNINGTEMP
blinking red
•The WARNINGTEMP. indicator continues to blink even after
the temperature inside the projector returns to normal. When
the projector is turned on again, the WARNINGTEMP. indicator
stops blinking.
Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if the air
vents of the projector are not blocked.
– Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the
projector away from the duct or vent.
– Is the filter clean? Replace the filter with a new one.
The projector is shut down; and the LAMP indicator is
lighting and other indicators are blinking.
Indicators
When the projector detects an abnormal condition, it
will be automatically shut down to protect the inside of
the projector and the LAMP indicator lights on and other
indicators blink. In this case, unplug the AC power cord and
plug it, and then turn on the projector once again to verify
operation. If the projector cannot be turned on and these
indicators are still lighting and blinking, unplug the AC power
cord and contact the service station.
CAUTION
LAMP indicator lights on
and other indicators blink
DO NOT LEAVETHE PROJECTOR WITHTHE
AC POWER CORD CONNECTED UNDER AN
ABNORMAL CONDITION. IT MAY RESULT IN FIRE
OR ELECTRIC SHOCK.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly
connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the
projector. Turn on equipment in the order of the projector and computer.)
6. If a problem still persists, check the following solutions.
Problem:
Solutions
– Plug the power cord of the projector into the AC outlet.
–Turn the MAIN ON/OFF switch to ON.
– Press the ON/STAND-BY Button to ON.
– Make sure the POWER indicator lights.
No power.
– Check the indicators. If the LAMP indicator lights and the other indicators blink, the
projector cannot be turned on. (Refer to page 70.)
– Check the projection lamp. (Refer to page 66.)
PIN code dialog box
appears at start-up.
– PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set (see
pages 24, 58-59)
The initial display is not
shown.
– Make sure “Off ” or “Countdown Off” are not chosen at Display function.
(See “SETTING” section on page 49)
The initial display is not
same with the default
one.
– Make sure “User” or “Off” are not chosen at Logo select function.
(See “SETTING” section on page 54)
When the projector is on
and you press the input
button, an icon other
than the Lamp mode icon
appears.
– That is the Filter warning icon. Refer to page 61.
An icon other than Input
mode or Lamp mode icon
appears.
– That is the Lamp replacement icon or the Filter warning icon. See pages 61, 66.
– Check the connection between your computer or video equipment and the projector.
– See if the input signal is correctly output from your computer. Some laptop computers
may need to be changed the setting for monitor output when connected to the
projector. See your computer’s instruction manual for the setting.
No image.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video equipment.
– Select correct input source once again through menu operation (See pages 32, 42).
– Make sure the temperature is not out of Operating Temperature
(41˚F–104˚F [5˚C–
40˚C]).
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
–
–
The end of lamp life is approaching. Replace the lamp with a new one promptly.
(See page 66)
appears on the screen
The filter is out of scroll. Replace the filter cartridge with a new one promptly.
(See pages 62-63)
appears on the screen
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
✔Note: Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such cases,
leave the projector OFF and wait until condensation evaporates.
– Projecting from excessive slant angle to the screen may cause keystone distortion and
partial imperfect focus.
The image is out of focus.
– Check if “Contrast” or “Brightness” are adjusted properly. (See page 46)
– Check if “Image level” is selected properly. (See pages 39, 43)
– Check the Lamp control function. ( See “SETTING” section on page 50)
– Check the Lamp 1/2 replace indicators. If it lights, the end of lamp life is approaching.
Replace the lamp with a new one promptly. (See page 66)
The image is not bright
enough.
–The image is darker when 1 lamp mode is selected, compared with 2 lamp mode.
Check the lamp mode at SETTING section on page 50.
– Check the Input signal, color system, video system, or computer system mode.
– Check the Ceiling / Rear function. (See pages 41, 45)
The color is strange.
The image is Left/Right
reversed.
The image isTop/Bottom
reversed.
– Check the Ceiling function. (See pages 41, 45)
The image is distorted or
runs off.
– Check “PC Adjust” menu or “ Screen” menu and adjust them.
– Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p,
720p, 480i, 575i, 1035i, 1080p, or 1080i is selected or when the digital signal is input
into DVI terminal. (See page 36)
Auto PC adjustment
function does not work.
Some displays are not
seen during the operation.
– Check the Display function (see page 49).
The setting does not
remain after turning off
power.
– Make sure you selected “Store” after adjusting settings. Some settings cannot be
stored if not registered with “Store”.
Power management
function does not work.
– Power management function cannot work while “Freeze” function is running or the
shutter is closed.
Image disappears
automatically.
– Check the power management function in the Setting. The power management is set
to "On" at the factory.
Capture function does not
work.
– Check the connection to see if there is signal.
Some menus cannot be
selected.
– Each of the Video Input and Computer Input has a limit on selectable menus.
7ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
The power is turned off
automatically.
– Power management function runs by initial setting. Check “SETTING” section on page
57.
You cannot operate with
the side control.
–The side control is not available If the side control is locked at “Key lock” under
“Security” of SETTING section. Please check “SETTING” section on page 58.
– Check the batteries.
– Check if the RC sensor is set properly. (See page 56)
– Make sure no obstruction is between the projector and remote control.
– Make sure you are not too far from the projector when using the remote control.
Maximum operating range is 16.4’ (5m).
– Make sure that the remote control code conforms to the projector’s code.
(See “SETTING” section on page 56.)
The Remote Control does
not work.
– Make sure the reset switch in the compartment lid on back of the remote control is set
to use position.
– Unlock the Key lock function for the remote control. (See page 58)
– Wireless remote control does not work when the remote control cable is connected to
the projector. (See page 15)
– Check the status of the projector with referring to “ INDICATORS AND PROJECTOR
CONDITION” on pages 77-79.
Indicators blinks or lights.
appears on the screen
–Your operation is invalid. Operate correctly.
Unable to unlock the Logo
PIN code lock, Security
key lock or Security PIN
code lock.
– Contact the dealer where you purchased the projector or the service center.
– Contact the dealer where you purchased the projector or the service center.
Forget the Logo PIN code
or Security PIN code.
WARNING:
High voltages are used to operate this projector Do not attempt to open the cabinet
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector
or the service center. Specify the model number and explain about the problem. We will advise you how to obtain
service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty, and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used.
7ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
MenuTree
Computer Input/Video Input
(1)
(1)
Input 1
RGB (PC analog)
RGB (Scart)
Go to System
Input
RGB (PC digital)
RGB (AV HDCP)
HDMI
Go to System
Go to System
Go to System
Go to System
Go to System
(1)
(1)
(1)
(3)
RGB
Input 2
Y, Pb/Cb,Pr/Cr
Video
(2)
(2)
Go to System
S-video
Go to System
Input 3
Input 4
(For Optional Interface Boards)
(For Optional Interface Boards)
Information
Image Adjust
Image Adjust
Contrast
Brightness
Color ✽
0–63
0–63
0–63
0–63
Color
Input
Information
H-sync freq.
V-sync freq.
Screen
Language
Lamp mode
Tint ✽
Color
management
Gamma
List
Color M.
Lamp control
Lamp interval
Lamp 1
MAllidDel
LMoewnu
Menu
Lamp 2
Color M.
Filter counter
Power management
Security
Off/L1/L2
Auto picture
control
Key lock
PIN code lock
BrilliantColor
Color temp.
Off/On
HXLigohw
MLoiwd
LMoiwd
High
Remote control
Shutter management
Remote Control
Projector
5 - 180 Min
Color wheel type
Lens type
SERIAL NO.
Adj.
Red
Green
Blue
0–63
0–63
0–63
Offset
Red/Green/Blue/Quit
Network
Sharpness
Gamma
0–31
0–15
Network
Network PIN code
Off/On
Network
Noise reduction ✽ Off/On
Progressive ✽
Off/On/Film
Reset
Store
Yes / No
Image 1
Image 10
Quit
Quit
✽
Displayed in grayout in the computer Input.
✔Note:
•The Menu display varies depending on the input signal.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Computer Input
(1)
Mode 1
Mode 2
SVGA 1
SVGA 2
SVGA 3
Standard
Real
System
Image Select
Dynamic
Image 1
Image 10
✽ System displayed in the System Menu varies depending on the input signal.
Auto PC adj.
Normal
True
PC Adjust
Screen
Fine sync.
Total dots
0–31
Full
Position H
Position V
Scale
H & V
Position
Common
Reset
H / V
On/Off
H / V
Custom
H-sync freq.
V-sync freq.
Quit
Current mode
Quit
Digital zoom +
Digital zoom -
Clamp
Display area - H
Display area - V
Reset
Keystone
Store
Reset
On/Off
On/Off
Yes/No
Ceiling
Rear
Mode free
Store
Mode 1
Reset
Quit
Yes/No
Mode 10
Quit
Quit
Video Input
(2)
(3)
Auto
Auto
System
System
PAL
1080p
1080i
1035i
720p
575p
480p
575i
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
480i
Standard
Cinema
Dynamic
Image 1
Normal
Zoom
Image Select
Screen
Natural Wide
Full
Custom
Scale
H / V
H & V
On/Off
Image 10
Position
Common
Reset
H / V
Quit
Keystone
Store
Reset
On/Off
On/Off
Yes/No
Ceiling
Rear
✔Note:
Reset
Quit
•The Menu display varies depending on the input signal.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Computer Input/Video Input
Fan control
Normal/Max
Code 1
Setting
Remote Control
Code 8
Language
12 languages provided.
Quit
Quit
RC sensor
All/Front &Top/Top & Back/Front & Back/
Front/Top/Back
Menu
Position/Simple Menu/Menu size/Quit
Off/Countdown Off/On
Display
Off/Ready/Shut down
1–30 Min.
Quit
Power management
Background
Lamp mode
Lamp control
Blue/User/Black
2-Lamps/Lamp1/Lamp2
Lamp control
Normal/Eco1/Eco2
Mode 1/Mode 2
On start
Security
On/Off
Lamp life control
Key lock
Off
Lamp interval
Off/Auto/24H/200H/500H/1000H/2000H
Projector
Remote Control
PIN code lock
Quit
Off/On1/On2
PIN code change
Quit
Picture in Picture
Off/User1-5
P in P/P by P
Main Picture/Sub picture
Input1-4
Size
Projector ID
Shutter
1–999
Position
Protection
Remote control
Projector
On / Off
On / Off
Main picture/Sub picture
Frame lock
Store
Yes/No
Yes/No
Yes/No
Management
5 - 180 Min.
Reset
Quit
Mode free
Quit
[ ] Hour(s)
Filter counter
Used time
Off/1000H/2000H/3000H
Edge blending
On/Off
0-960
Reset
Quit
Yes/No
Left/Right width
Top/Bottom width
Black level
0-540
All
Scrolls remaining
Scroll(s)
127
R/G/B
On/Off
Yes/No
Yes/No
Reset
Quit
Test pattern
Reset
Quit
Quit
Test pattern
8 test patterns provided
Quit
Color matching
On/Off
Factory default
Quit
Yes/No
Red/Green/Blue/White
Auto test pattern
0.000-1.000
On/Off
Reset
Store
Yes/No
Yes/No
Advanced color matching
Advanced color matching
On/Off
Quit
Measured
Red/Green/Blue/Half white/White
or
Red/Green/Blue/White
Red/Green/Blue/Cyan/Magenta/Yellow/White
Target
On/Off
AutoTest pattern
Reset
Yes/No
Yes/No
Store
(Measured) Red/Green/Blue/Half white/White
or
(Measured) Red/Green/Blue/White
(Target) Red/Green/Blue/Cyan/Magenta/Yellow/White
Test pattern
Quit
DynamicBlack
HDMI setup
Logo
Off/Low/High
Normal/Enhanced
Off/Default/User
Logo select
Capture
Yes/No
On/Off
Logo PIN code lock
Logo PIN code change
Quit
Quit
Filter control
Yes/No
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for the projector condition.
The projector is operating normally
Indicators
WARNING WARNING
LAMP 1/2
REP.
orange
Projector Condition
LAMP
red
POWER
green
SHUTTER
blue
TEMP.
FILTER
red
orange
The projector is off. (The main On/Off switch is OFF
position or the AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/
STAND-BY button to turn on the projector.
✽
✽
✽
✽
✽
The projector is operating normally.
(The Shutter is open)
The projector is operating normally.
(The Shutter is closed)
✽
✽
✽
✽
The projector is preparing for stand-by or the
projection lamp is being cooled down. The projector
cannot be turned on until cooling is completed and
the POWER indicator lights green.
✽
The projection lamp is being cooled down in the
Power management mode.
✽
✽
✽
✽
✽
The projector is in the Power management mode.
The projection lamp is being cooled down in the
Shutter management mode.
✽
✽
✽
The projector is in the Shutter management mode.
Press the ON/STAND-BY button to turn on the
projector.
✽
✽
The filter is scrolled using the FILTER button on
the remote control or the Filter control function in
the setting menu. When the filter is being scrolled,
the Filter replacement icon and “Please wait...”
message (Fig. 1) appear on the screen.
Fig 1 Filter replacement icon and “Please wait...”
• • • on
• • • blinking slow
(approx. 2 seconds ON,
• • • blinking at the normal rate
(approx. 1 second ON,
1 second OFF)
2 seconds OFF)
• • • dim
• • • off
• • •blinking fast
• • • Differs according to conditions.
✽
(approx. 0.5 seconds ON,
0.5 seconds OFF)
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
The projector is detecting abnormal condition
Indicators
WARNING WARNING
LAMP 1/2
REP.
orange
Projector Condition
LAMP
red
POWER
green
SHUTTER
blue
TEMP.
FILTER
red
orange
The temperature inside the projector is elevated
close to the abnormally high level.
✽
✽
✽
✽
✽
✽
The temperature inside the projector is abnormally
high. The projector cannot be turned on. When
the projector is cooled down enough and the
temperature returns to normal, the POWER
indicator lights green and the projector can be
turned on. (The WARNINGTEMP. indicator keeps
blinking.)
The projector has been cooled down enough and
the temperature returns to normal. When turning on
the projector, the WARNINGTEMP. indicator stops
blinking. Check and replace the filter.
✽
✽
✽
✽
✽
The lamp cannot light up. (The projector is preparing
for stand-by or the projection lamp is being cooled
down. The projector cannot be turned on until
cooling is completed.)
The lamp cannot light up. (The lamp has been
cooled down enough and the projector is in stand-
by mode and ready to be turned on with the ON/
STAND-BY button.)
✽
✽
✽
✽
✽
✽
When either of the 2 lamps is out, the projector
operates with 1 lamp.
✽
✽
The lamp has been used overtime. Replace the
lamp immediately.
✽
✽
WARNING FILTER
When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING
FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cartridge with a new
one promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.64).
LAMP REPLACE 1 and ꢀ
When the LAMP 1 REPLACE indicator and the LAMP 2 REPLACE indicator light orange, replace the projection lamps
with new ones promptly. See page 66.
7ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
The projector is detecting abnormal condition
Indicators
WARNING WARNING
LAMP 1/2
REP.
orange
Projector Condition
LAMP
red
POWER
green
SHUTTER
blue
TEMP.
FILTER
red
orange
If the Filter counter reached a time set in the timer
setting, a Filter replacement icon (Fig.2) appears
on the screen and the WARNING FILTER indicator
on the top panel lights up. Replace the filter as
soon as possible. If the filter is out of scroll and the
projector reaches a time set in the timer setting, Fig.
3 appears on the screen and the WARNING FILTER
indicator lights up. Replace the filter cartridge as
soon as possible.
✽
✽
Fig ꢀ Filter replacement icon
If the filter is clogged and no scroll is left in the filter
cartridge, a Filter cartridge replacement icon (Fig.4)
appears on the screen and the WARNING FILTER
indicator lights up. Replace the filter cartridge as
soon as possible.
Fig ꢁ
✔Note:
Fig 4 Filter cartridge replacement icon
•Fig.2, Fig.3 and Fig.4 icon will not appear when
the Display function is set to “Off” (p.49), or during
“Freeze” (p.30).
The projector detects an abnormal condition during
filter scroll.
✽
✽
✽
✽
✽
✽
The projector is being cooled down after detecting
an abnormal condition during filter scroll.
The projector has been cooled down enough and is
in the stand-by mode after detecting an abnormal
condition during filter scroll.
The filter cartridge is not installed in the projector.
Check the filter compartment to see if the filter
cartridge is installed in the projector. When the filter
cartridge is installed and the indicators continue to
light and blink, read the column below.
The projector detects an abnormal condition and
cannot be turned on. Unplug the AC power cord and
plug it again to turn on the projector. If the projector
is turned off again, unplug the AC power cord and
contact the dealer or the service center. Do not
leave the projector on. It may cause an electric
shock or a fire hazard.
✽
✽
The shutter is out of control.
✽
✽
✽
The shutter is out of control. (The projector is in the
cooling mode.)
✽
✽
✽
The shutter is out of control. (The projector is in the
stand-by mode.) In that case, contact the service
station immediately.
✽
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below
and less than 230 MHz of Dot Clock.
ON-SCREEN
DISPLAy
VGA 1
ON-SCREEN
DISPLAy
SXGA 8
RESOLUTION H-Freq (kHz) V-Freq (Hz)
RESOLUTION H-Freq (kHz) V-Freq (Hz)
640x480
720x400
640x400
640x480
640x480
640x480
640x480
640x480
640x480
640x480
768x575
31.470
31.470
31.470
37.860
37.860
37.500
43.269
34.970
35.000
31.470
31.250
59.880
70.090
70.090
74.380
72.810
75.000
85.000
66.600
66.670
59.880
50.000
1280x1024
1280x1024
1280x960
1152x900
1152x900
63.980
79.976
60.000
61.200
71.400
60.020
75.025
60.000
65.200
75.600
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480p
SXGA 9
SXGA 10
SXGA 11
SXGA 12
1280x1024
(Interlace)
SXGA 13
50.000
86.000
1280x1024
(Interlace)
1280x1024
1280x1024
1152x900
SXGA 14
50.000
94.000
SXGA 15
SXGA 16
SXGA 17
63.370
76.970
61.850
60.010
72.000
66.000
575p
768x576
(Interlace)
575i
15.625
50.000
1280x1024
(Interlace)
SXGA 18
46.430
86.700
640x480
(Interlace)
480i
15.734
60.000
SXGA 19
SXGA 20
SXGA+ 1
SXGA+ 2
SXGA+ 3
SXGA+ 4
SXGA+ 5
MAC 21
MAC
1280x1024
1280x1024
1400x1050
1400x1050
1400x1050
1400x1050
1400x1050
1152x870
1280x960
1280x1024
1366x768
1360x768
1376x768
1360x768
1280x768
1280x768
1280x768
1280x800
1280x800
1280x800
1920x1200
1920x1200
1680x1050
1440x900
1440x900
1600x1200
1600x1200
1600x1200
1600x1200
1600x1200
1280x720
1280x720
63.790
91.146
63.970
65.350
65.120
64.030
62.500
68.680
75.000
80.000
48.360
47.700
48.360
56.160
47.776
60.289
68.633
49.600
41.200
49.702
74.556
74.038
65.290
55.935
74.918
75.000
81.250
87.500
93.750
106.250
45.000
37.500
60.180
85.024
60.190
60.120
59.900
60.010
58.600
75.060
75.080
75.080
60.000
60.000
60.000
72.000
59.870
74.893
84.837
60.050
50.000
59.810
59.885
59.950
59.954
59.887
60.000
60.000
65.000
70.000
75.000
85.000
60.000
50.000
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
832x624
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
35.156
37.880
46.875
53.674
48.080
37.900
34.500
38.000
38.600
32.700
38.000
49.720
48.360
68.677
60.023
56.476
60.310
48.500
44.000
63.480
56.250
60.320
75.000
85.060
72.190
61.030
55.380
60.510
60.310
51.090
60.510
74.550
60.000
84.997
75.030
70.070
74.920
60.020
54.580
79.350
MAC
WXGA 1
WXGA 2
WXGA 3
WXGA 4
WXGA 6
WXGA 7
WXGA 8
WXGA 9
WXGA 10
WXGA 11
WUXGA 1
WUXGA 2
WSXGA+ 1
WXGA+ 1
WXGA+ 2
UXGA 1
UXGA 2
UXGA 3
UXGA 4
UXGA 5
720p
✽
1024x768
(Interlace)
XGA 9
36.000
87.170
XGA 10
XGA 11
1024x768
1024x768
62.040
61.000
77.070
75.700
✽
✽
✽
✽
✽
✽
1024x768
(Interlace)
XGA 12
35.522
86.960
XGA 13
XGA 14
XGA 15
MAC 19
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
1024x768
1024x768
1024x768
1024x768
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x1024
1280x1024
46.900
47.000
58.030
60.240
64.200
62.500
63.900
63.340
63.740
71.690
81.130
58.200
58.300
72.000
75.080
70.400
58.600
60.000
59.980
60.010
67.190
76.107
720p
1920x1035
1035i
1080i
33.750
33.750
28.125
60.000
60.000
50.000
(Interlace)
1920x1080
(Interlace)
1920x1080
(Interlace)
✽
“True” cannot be selected when WUXGA1, WXGA+2, UXGA1, UXGA2, UXGA3, UXGA4 and UXGA5 are
selected. (p.40)
ꢂ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
ON-SCREEN
DISPLAy
RESOLUTION H-Freq (kHz) V-Freq (Hz)
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
33.750
28.125
27.000
67.500
56.250
33.750
28.125
27.000
30.000
25.000
24.000
60.000
50.000
60.000
50.000
48.000
1080p
1080psf/30
1080psf/25
1080psf/24
When an input signal is digital from the DVI terminal, refer to the chart below.
ON-SCREEN
DISPLAy
ON-SCREEN
DISPLAy
RESOLUTION H-Freq (kHz) V-Freq (Hz)
RESOLUTION H-Freq (kHz) V-Freq (Hz)
D-VGA
D-480p
D-575p
D-SVGA
640x480
720x480
720x575
31.470
31.470
31.250
37.879
43.363
48.360
47.700
48.360
56.160
46.500
47.776
60.289
68.633
49.600
41.200
49.702
63.980
60.276
63.970
65.350
65.120
59.940
59.880
50.000
60.320
60.000
60.000
60.000
60.000
72.000
50.000
59.870
74.893
84.837
60.050
50.000
59.810
60.020
58.069
60.190
60.120
59.900
D-WUXGA 2
D-WSXGA+ 1
D-WXGA+ 1
D-720p
1920x1200
1680x1050
1440x900
1280x720
1280x720
1920x1035
(Interlace)
1920x1080
(Interlace)
1920x1080
(Interlace)
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
74.038
65.290
55.935
45.000
37.500
59.950
59.954
59.887
60.000
50.000
800x600
D-XGA
1024x768
1366x768
1360x768
1376x768
1360x768
1366x768
1280x768
1280x768
1280x768
1280x800
1280x800
1280x800
1280x1024
1280x1024
1400x1050
1400x1050
1400x1050
D-720p
D-WXGA 1
D-WXGA 2
D-WXGA 3
D-WXGA 4
D-WXGA 5
D-WXGA 6
D-WXGA 7
D-WXGA 8
D-WXGA 9
D-WXGA 10
D-WXGA 11
D-SXGA 1
D-SXGA 2
D-SXGA+ 1
D-SXGA+ 2
D-SXGA+ 3
D-1035i
33.750
33.750
28.125
60.000
60.000
50.000
D-1080i
D-1080psf/30
D-1080psf/25
D-1080psf/24
33.750
28.125
27.000
33.750
28.125
27.000
67.500
56.250
60.000
50.000
48.000
30.000
25.000
24.000
60.000
50.000
D-1080p
✔Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
•Specifications are subject to change without notice.
When the input signal is digital from the HDMI terminal, refer to the chart below.
H-Freq
(kHz)
V-Freq
(Hz)
System
mode
H-Freq
(kHz)
V-Freq
(Hz)
System
mode
RESOLUTION
RESOLUTION
D-575p
D-720p
D-720p
D-1080i
D-1080i
D-1080p
D-1080p
D-1080p
720x575
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
−
−
−
−
−
−
−
−
50.00
59.94/60
50.00
D-VGA
D-WXGA6
D-WXGA7
D-WXGA8
D-WXGA9
D-WXGA10
D-480i
640x480
1280x768
1280x768
1280x768
1280x800
1280x800
720x480
720x575
720x480
−
59.94/60
59.870
74.893
47.776
60.289
68.633
49.572
41.200
−
59.94/60
50.00
84.837
59.870
50.000
59.94/60
50.00
59.94/60
50.00
24.00
D-575i
−
D-480p
−
59.94/60
✔Note:
•You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.
ꢂ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
List of Picture in Picture
On-Board
Optional Interface Board
Dsub
-DVI
Component
HDCP
-DVI
HD
wireless
Input1
Input2
Dsub
Component
SDI
-S-video
Analog PC
Scart
o
o
o
o
o
o
o
o
o
-
o
-
o
-
o
-
o
o
-
o
-
o
-
o
-
o
-
o
-
o
-
o
-
o
o
-
o
o
-
o
o
-
On-Board
Input1
Digital
o
o
o
o
o
o
o
-
o
o
o
o
-
o
o
o
-
-
o
o
o
-
o
o
o
-
o
o
o
-
o
o
o
-
o
o
o
-
o
o
o
-
-
Analog PC
Component
o
o
o
o
o
-
o
o
o
o
o
-
o
o
o
o
o
o
o
o
o
On-Board
Input2
Video/
S-Video
o: Picture in Picture combinations are enabled
- : Picture in Picture combinations are disabled
✔Note:
•You cannot select Input 3 and Input 4 (e.g. SDI and HD wireless) simultaneously as images of Main picture and Sub
picture.
• When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture.
• Depending on the frequency or signal type of PC/AV input, the display resolution may be lowered or images may not be
displayed on the Main/Sub picture.
<Display resolution is lowered when;>
• Inputting PC analog signals: Between 100-160 MHz
• Inputting AV analog signals: 1080p
<Images are not displayed and X mark appears when;>
• Inputting PC analog signals: More than 160MHz
• Inputting PC digital signals: More than 100MHz
• Inputting AV digital signals: 1080p
ꢂꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Mechanical Information
ProjectorType
Multi-media Projector
Dimensions (W x H x D)
Net Weight
15.75” x 9.55” x 20.61” (400.0 mm x 242.5 mm x 523.5 mm)
43.65lbs (19.8 kg)
0˚ to 5˚
Feet Adjustment
DLPChip
Projection System
0.95” Single DLP chip, High brightness color wheel x 2
2,073,600 pixels (1,920 x 1,080 dots)
Number of Pixels
Signal Compatibility
Color System
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, 1080p, and 1080i
H-sync. 15 kHz–120 kHz, V-sync. 48 Hz–120 Hz
High DefinitionTV Signal
Scanning Frequency
Optical Information
Projection Lamp
330 W UHP lamp x 2
Interface
Input 1
DVI-DTerminal (Digital), Mini D-Sub 15-pinTerminal (Analog), HDMI
Input 2
BNCType x 5 (VIDEO/Y/G, B/Pb/Cb, R/Pr/Cr, H/HV and V), S-Video
Input 3
Vacant
Input 4
Network Board
Monitor Output
Other Jacks
Mini D-sub 15 pin
Serial port in (D-sub 9), Serial port out (D-sub 9), USB port, and Wired Remote Jack
Power
Voltage and Power Consumption
AC 100–120 V (9.2A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200-240 V (4.4A Max. Ampere), 50/60 Hz (Continental Europe andThe U.K.)
Operating Environment
OperatingTemperature
StorageTemperature
41˚F–104˚F (5˚C–40˚C)
14˚F–140˚F (-10˚C–60˚C)
Remote Control
Battery
AA or LR6Type x 2
Operating Range
Dimensions
16.4’ (5 m/ 30˚)
1.79” (W) x 1.03” (H) x 6.24” (D) (45.5 mm x 26.2 mm x 158.5 mm)
4.1 oz (117 g) (including batteries)
Net Weight
Accessories
Owner’s Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Remote Control and Batteries
VGA Cable
PIN Code Label
Cable covers (support cover & cover)
Fixing bracket for power cord
Rich color reproduction color wheel x 2
Ferrite core (for LAN cable)
Strap x 2
Cable tie x 3
Real Color Manager Pro (CD-ROM)
ꢂꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
lThe specifications are subject to change without notice.
l Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by side, you may recognize different white balance
and color uniformity on each projector.
Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Model No.
Wired Remote Cable(30m)
: POA-CA-RC30
Optional Interface Board (DVI)
: POA-MD18DVI
Optional Interface Board (5-BNC)
: POA-MD16VD1
: POA-MD04VGA
: POA-MD17SDID
: POA-MD23ADI
: POA-MD25VD3
: POA-MD26HDWL
: POA-HDTM01
Optional Interface Board (D-sub 15)
Optional Interface Board (Dual-SDI)
Optional Interface Board (DVI / D-sub 15)
Optional Interface Board (5-BNC / VIDEO)
Optional Interface Board (HD DATA Wireless Receiver)
HD DATA Wireless Transmitter Box
✔Note:
• Between the two features of the provided Real Color Manager Pro (CD-ROM); "Color Correction" and "Gamma Correction", "Color
Correction" is not available with this projector.
ꢂ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configurations ofTerminals
ANALOG (Mini D-sub 15 pin)
Input
Red Input
Green Input
Blue Input
+5V Power
Ground (Vert. sync.)
Ground
DDC Data
Horiz. sync.
Vert. sync.
1
ꢀ
ꢁ
4
5
6
7
ꢂ
9
2
5
1
4
3
10
9
8
7
6
10
11
1ꢀ
1ꢁ
14
15
15
12
11
14
13
No Connect
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
DDC Clock
Output
Red Output
Green Output
Blue Output
No Connect
Ground (Vert.sync.)
No Connect
1
ꢀ
ꢁ
4
5
6
7
ꢂ
9
10
11
1ꢀ
1ꢁ
14
15
No Connect
No Connect
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
Horiz. sync. Output
Vert. sync. Output
No Connect
DIGITAL DVI-D (DVI ꢀ4 PIN)
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
No Connect
DDC Clock
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
No Connect
+5V Power
T.M.D.S. Data0–
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
1
ꢀ
ꢁ
4
5
6
7
ꢂ
9
17
1ꢂ
19
ꢀ0
ꢀ1
ꢀꢀ
ꢀꢁ
ꢀ4
10
11
1ꢀ
1ꢁ
14
15
16
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
No Connect
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
DDC Data
No Connect
Ground (for +5V)
Hot Plug Detect
USB CONNECTOR (Series B)
HDMI
1
ꢀ
ꢁ
4
Vcc
- Data
+ Data
Ground
1
3
5
7
9
11 13 15 17 19
10 12 14 16 18
2
3
1
4
2
4
6
8
19 PinType A
1
2
3
4
5
6
7
8
9
TMDS Data 2+ Input 11 Ground (TMDS Clock)
Ground (TMDS Data 2) 12 TMDS Clock- Input
TMDS Data 2- Input
TMDS Data 1+ Input 14
13
-----
-----
CONTROL PORT CONNECTOR (D-sub 9 pin)
Ground (TMDS Data 1) 15 SCL
TMDS Data 1- Input
16 SDA
TMDS Data 0+ Input 17 Ground (DDC/CEC)
Ground (TMDS Data 0) 18 +5V Power
Serial
1
ꢀ
ꢁ
4
5
6
7
ꢂ
9
-----
R X D
T X D
-----
SG
-----
RTS
CTS
-----
TMDS Data 0- Input
19 Plug insert detection
10 TMDS Clock+ Input
ꢂ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or
lost the number and unable to operate the projector, contact the service station.
PIN Code Lock No.
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
*Should the four-digit number be
changed, the factory set number will
be invalid.
While the projector is locked with the PIN code...
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN code.
ꢂ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
Unit: inch (mm)
Screw Holes for Ceiling Mount
Screw: M8
Depth: 0.393 (10.0)
6.81(173.0) 6.81(173.0)
6.02(153.0) 5.63(143.0)
15.75(400.0)
5.0º
96.0º
19.96(507.1)
4.92(125.0) 5.79(147.0)
5.0º
6.50(165.0) 6.50(165.0)
ꢂ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial
port.
Operation
Connect a RS-232C serial cross cable to SERIAL
PORT IN on the projector and serial port on the PC.
(See p.11)
Baud rate
Parity check
Stop bit
: 9600 / 19200 bps
: none
: 1
1
Flow control
Data bit
: none
: 8
Launch a communication software provided with PC
and setup the communication condition as follows:
2
3
✔Note:
Type the command for controlling the projector and
then enter the "Enter" key.
•The default of the baud rate is set to 19200 bps. If an
error occurs in the communication, change the serial
port and the communication speed (baud rate).
•ꢀEnter with ASCII 64-byte capital characters and one-
byte characters.
Example
When you want to change the input to INPUT 2,
Type 'C' '0' '6' 'Enter'.
Functional Execution Command
Format
The command is sent from PC to the projector with
the format below;
'C' [Command] 'CR'
Command: two characters (refer to the
command table below.
-The projector decodes the command and returns the
'ACK' with the format below;
'ACK' 'CR'
-When the projector cannot decode the command, it
returns with format below.
Command
C3B
C3C
C3D
C3F
Function
Pointer LEFT
Pointer UP
Pointer DOWN
Enter
‘?’ ‘CR’
Command
C00
Function
Turn the projector ON
C46
C47
Zoom DOWN
Zoom UP
Turn the projector OFF
(immediately OFF)
C01
C4A
C4B
C5D
C5E
C5F
C60
C89
C8E
C8F
C90
Focus DOWN
Focus UP
C05
C06
C07
C08
C0D
C0E
C0F
C10
C1C
C1D
C3A
Select Input 1
Select Input 2
Select Input 3
Select Input 4
Video mute ON
Video mute OFF
Aspect 4:3
Aspect 16:9
Menu ON
Menu OFF
Pointer RIGHT
Lens shift UP
Lens shift DOWN
Lens shift LEFT
Lens shift RIGHT
Auto PC Adj.
Keystone UP
Keystone DOWN
Keystone RIGHT
Keystone LEFT
C91
ꢂꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Status Read Command
Format
The command is sent from PC to the projector with
the format below;
'CR' [Command] 'CR'
Command: one character (refer to the command
table below.
The projector decodes the command and returns the
'Character string' with the format below;
Projector
Return
Command
Function
Projector status
Power On
00
80
40
20
10
28
02
24
04
Stand-by mode
Countdown
Cooling down
Power Malfunction
Cooling down at the temperature anomaly
Unable to receive the RC232C command.
Cooling down at Power Management mode
Power Management mode after Cooling down
CR0
Status Read
Cooling down after the projector is turned off when the lamps
are out.
Stand-by mode after Cooling down when the lamps are out.
21
81
88
Stand-by mode after Cooling down at the temperature
anomaly.
Cooling down when the projector is turned off by the shutter
management function.
2C
8C
Stand-by mode after Cooling down by the shutter
management function.
S1 =Temperature at Sensor 1 (˚C)
S2 =Temperature at Sensor 2 (˚C)
S3 =Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C, S2 = 23.4˚C, S3 = 34.5˚C
-->The projector displays “12.3 23.4 34.5”
CR6
Temperature Read
S1 S2 S3
(For each sensor, two digit and the tenth place numbers are
displayed with a space between each temperature.)
Communication failure
?
The tables on pages 88 and 89 show the typical command lists for controlling the projector. Please consult your
local dealer for further information of other commands.
ꢂ9
Download from Www.Somanuals.com. All Manuals Search And Download.
KT5AL-A
SANyO Electric Co , Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
|
