Owner’s Manual
HD DATA WIRELESS Transmitter Box
Model POA-HDTM01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Basic Setting and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Single Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Broadcast Mode Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Other Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Maintenance and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Before operating this transmitter, read
this manual thoroughly and operate the
transmitter properly.
Operating the transmitter properly
enables you to manage those features
and maintains it in better condition for a
considerable time.
Safety Precaution
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR
MOISTURE.
Improper operation may result in not
only shortening the product-life, but
also malfunctions, fire hazard, or other
accidents.
– If the transmitter is unused for an
extended time, unplug the transmitter
from the AC power outlet.
If your transmitter seems to operate
improperly, read this manual again, check
operations and cable connections and
try the solutions in the "Troubleshooting"
section in the end of this manual. If the
problem still persists, contact the dealer
where you purchased the transmitter or the
service center.
NOTE:
This symbol and recycle
system are applied only
to EU countries and not
applied to the countries
in the other area of the
world.
Your SANYO product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
CAUTION
RISK OF ELECTRONIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Please dispose of this equipment at
your local community waste collection/
recycling centre.
In the European Union there are separate
collection systems for used electrical and
electronic products.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
Please help us to conserve the
environment we live in!
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München,
Germany
Important Notice
There are restrictions on the channels
and frequencies in the countries and
regions at which you can use the wireless
communication. So it is forbidden to take
the transmitter and the receiver outside
the country or region where you purchased
them.
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka
574-8534, Japan
READ AND KEEP THIS OWNER'S
MANUAL FOR LATER USE.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions
should be read before the product is
operated.
Slots and openings in the back and
bottom of the cabinet are provided for
ventilation, to ensure reliable operation
of the equipment and to protect it from
overheating.
Read all of the instructions given here
and retain them for later use. Unplug this
transmitter from AC power supply before
cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
The openings should never be covered with
cloth or other materials, and the bottom
opening should not be blocked by placing
the transmitter on a bed, sofa, rug, or other
similar surface. This transmitter should
never be placed near or over a radiator or
heat register.
Follow all warnings and instructions marked
on the transmitter.
For added protection to the transmitter
during a lightning storm, or when it is left
unattended and unused for long periods
of time, unplug it from the wall outlet. This
will prevent damage due to lightning and
power line surges.
This transmitter should not be placed in
a built-in installation such as a book case
unless proper ventilation is provided.
Never push objects of any kind into this
transmitter through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a fire or
electric shock. Never spill liquid of any kind
on the transmitter.
Do not expose this unit to rain or use near
water... for example, in a wet basement,
near a swimming pool, etc...
Do not use attachments not recommended
by the manufacturer as they may cause
hazards.
Do not install the transmitter near the
ventilation duct of air-conditioning
equipment.
Do not place this transmitter on an unstable
cart, stand, or table. The transmitter may
fall, causing serious injury to a child or adult,
and serious damage to the transmitter. Use
only with a cart or stand recommended
by the manufacturer, or sold with the
transmitter. Wall or shelf mounting should
follow the manufacturer's instructions, and
should use a mounting kit approved by the
manufacturers.
This transmitter should be operated only
from the type of power source indicated
on the marking label. If you are not sure of
the type of power supplied, consult your
authorized dealer or local power company.
Do not overload wall outlets and extension
cords as this can result in fire or electric
shock. Do not allow anything to rest on the
power cord. Do not locate this transmitter
where the cord may be damaged by
persons walking on it.
An appliance and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the appliance and cart
combination to overturn.
Do not attempt to service this transmitter
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified
service personnel.
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Unplug this transmitter from wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a. When the power cord or plug is
damaged or frayed.
b. If liquid has been spilled into the
transmitter.
c. If the transmitter has been exposed to
rain or water.
d. If the transmitter does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operating
instructions as improper adjustment
of other controls may result in damage
and will often require extensive work
by a qualified technician to restore the
transmitter to normal operation.
e. If the transmitter has been dropped or
the cabinet has been damaged.
f. When the transmitter exhibits a distinct
change in performance-this indicates a
need for service.
When replacement parts are required,
be sure the service technician has
used replacement parts specified by
the manufacturer that have the same
characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock, or injury to persons.
Upon completion of any service or
repairs to this transmitter, ask the service
technician to perform routine safety checks
to determine that the transmitter is in safe
operating condition.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
CAUTION IN CARRYING OR TRANSPORTING THE TRANSMITTER AND THE
RECEIVER
- The transmitter and the receiver are precision equipment. Do not drop, bump, or subject
it to strong forces. Doing so may cause damage or malfunction of the transmitter or the
receiver.
- When transporting the projector, make sure that the receiver is removed from the
projector. Do not transport the projector with the receiver installed. To do so may cause
damage or malfunction of the receiver or the projector.
CAUTION IN HANDLING THE RECEIVER
When the receiver is inserted into the projector, the cover of the receiver protrudes from the
cabinet of the projector.
- Do not push or hit the receiver.
- Do not put anything on the receiver.
- Do not hold it when lifting or moving the projector. Doing so may cause damage to the
receiver or the projector.
CAUTION IN HANDLING THE TRANSMITTER
- Do not put anything on the cabinet of the transmitter. To do so may cause damage or
malfunction of the transmitter.
Air Circulation
- The openings in the cabinet are provided for ventilation. To ensure reliable operation of
the transmitter and to protect it from overheating, these openings must not be blocked or
covered.
- Keep the openings at least 10cm away from any objects.
Caution about Radio Wave
This unit operates in 5.2 GHz band, the same frequency band used for industrial, scientific,
and medical equipment (such as pacemaker).
Please make sure the following cautions.
1. Be sure that there are no other devices in the area that may use the same frequency band
as Transmitter.
2. If any other devices are causing radio interferences, move to other location.
3. Do not set up this unit outside. This unit operates in 5.2 GHz band, so it is designated for
indoor use only.
Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
HD DATA WIRELESS TRANSMITTER BOX
ꢅ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the
following two conditions: (1) the device may not cause interference, and (2) the device must accept
any interference, including interference that may cause undesired operation of this device.
CAUTION: Properly shielded a grounded cables and connectors must be used for connection to host
computer and /or peripherals in order to meet FCC emission limits.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RF Exposure Warning
- This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
- This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment
and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This
equipment must be installed and operated with at least 20cm and more between the radiator and
person’s body (excluding extremities: hands, wrists, feet and ankles).
For Canadian Users
This Class A digital apparatus complies with Canadian ICES-003.
Cet apparei numérique de la classe A est conforme à la norme NMB-003 du Canada.
ꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
The CE Mark is a Directive conformity mark of the
European Community (EC).
The Alert Mark is a Directive conformity mark of the
European Community.
Hereby, SANYO FISHER Sales (Europe) GmbH, declares that this Wireless Tx Module (AMN11100) is in
compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
SANYO FISHER Sales (Europe) GmbH tímto prohlašuje, že tento WLAN Module (AMN11100) je ve
shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede SANYO FISHER Sales (Europe) GmbH erklærer herved, at følgende udstyr WLAN
Module (AMN11100) overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt SANYO FISHER Sales (Europe) GmbH, dass sich das Gerät WLAN Module (AMN11100)
in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
English
Česky
[Czech]
Dansk
[Danish]
Deutsch
[German]
Käesolevaga kinnitab SANYO FISHER Sales (Europe) GmbH seadme WLAN Module (AMN11100)
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
Eesti
[Estonian]
Por medio de la presente SANYO FISHER Sales (Europe) GmbH declara que el WLAN Module
(AMN11100) cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Español
[Spanish]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ SANYO FISHER Sales (Europe) GmbH ΔΗΛΩΝΕΙ ΟΤΙ WLAN Module (AMN11100)
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Ελληνική
[Greek]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvių
Par la présente SANYO FISHER Sales (Europe) GmbH déclare que l’appareil WLAN Module (AMN11100) est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente SANYO FISHER Sales (Europe) GmbH dichiara che questo WLAN Module (AMN11100) è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo SANYO FISHER Sales (Europe) GmbH, deklarē, ka WLAN Module (AMN11100) atbilst Direktīvas
1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo SANYO FISHER Sales (Europe) GmbHdeklaruoja, kad šis WLAN Module (AMN11100) atitinka
[Lithuanian] esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands Hierbij verklaart SANYO FISHER Sales (Europe) GmbH dat het toestel WLAN Module (AMN11100) in
[Dutch]
Malti
[Maltese]
Magyar
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Hawnhekk, SANYO FISHER Sales (Europe) GmbH, jiddikjara li dan WLAN Module (AMN11100) jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, SANYO FISHER Sales (Europe) GmbH nyilatkozom, hogy a WLAN Module (AMN11100)
[Hungarian] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym SANYO FISHER Sales (Europe) GmbH oświadcza, że WLAN Module (AMN11100) jest
zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Polski
[Polish]
Português SANYO FISHER Sales (Europe) GmbH declara que este (AMN11100) está conforme com os requisitos
[Portuguese] essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko SANYO FISHER Sales (Europe) GmbH izjavlja, da je ta (AMN11100) v skladu z bistvenimi zahtevami in
[Slovenian] ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
Suomi
SANYO FISHER Sales (Europe) GmbH týmto vyhlasuje, že (AMN11100) spĺňa základné požiadavky a
všetky príslušné ustanovenia Smernice 1999/5/ES.
SANYO FISHER Sales (Europe) GmbH vakuuttaa täten että (AMN11100) tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar SANYO FISHER Sales (Europe) GmbH att denna (AMN11100) står I överensstämmelse
med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
[Finnish]
Svenska
[Swedish]
Islenska
Hér með lýsir SANYO FISHER Sales (Europe) GmbH yfir því að (AMN11100) er í samræmi við
[Icelandic] grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Norsk
SANYO FISHER Sales (Europe) GmbH erklærer herved at utstyret (AMN11100) er i samsvar med de
[Norwegian] grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
HD DATA WIRELESS TRANSMITTER BOX
ꢇ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Declaration of Conformity
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Before use
Package contents
The package contains following items. Check each item when unpacking the package. If
you have any of the following items missing, contact the sales dealer.
❑ HD DATA WIRELESS Transmitter
1 piece
❑ AC-DC Converter
❑ AC Power Cord
❑ Stand
1 piece
1 piece
2 pieces
1 piece
❑ Owner's Manual
Trademarks and Copyright
Each name of corporation or product in this Owner’s Manual is either a registered trademark or a
trademark of its respective corporation.
Notes
- The contents of this manual are subject to change without notice.
- We shall not be responsible for any damages caused by reliance on this manual.
- The word "projector" found in this manual means "projector provided with the HD DATA WIRELESS
Board" unless otherwise noted.
- The word "receiver" in this manual means "HD DATA WIRELESS Receiver Board: POA-MD26HDWL".
HD DATA WIRELESS TRANSMITTER BOX
11
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Part Names and Functions
Front
q
w
e
r
t
y
u
i
o
!
LINK INDICATOR
RESET BUTTON
y
q
- When the wireless configuration
is set up correctly and the wireless
communication is established with
the wireless receiver at the single
mode, this indicator lights orange.
- This indicator lights orange during
operation in the broadcast mode.
A built-in micro processor which
controls this unit may occasionally
malfunction and need to be reset.
This can be done by pressing this
RESET button with a pen, which will
shut down and restart the unit. Do
not use the RESET function exces-
sively.
LCD DISPLAY
INPUT INDICATORS
u
w
Display the selected menu. The back
light LED will be turned off when
the transmitter is not operated for 3
minutes.
An indicator of the selected input
lights blue.
POINT
BUTTONS
INPUT BUTTON
e
r
t
i
o
!
ed7 8
Select an item or adjust the value on
the menu on the display.
Select an input source.
MENU BUTTON
SELECT BUTTON
Open or close the menu on the
display.
Execute the selected menu.
ON/STAND-BY BUTTON
POWER INDICATOR
Turn the transmitter on or off.
- Lights red when the transmitter is
in stand-by mode.
- Lights green during operation.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
q
w
e
Rear
r
t
y
INPUT 1 COMPONENT
DC 16V
q
r
t
Connect component output signal
(Y-Pb/Cb-Pr/Cr) from video equip-
ment to this terminal.
Connect the AC adapter (supplied).
SERIAL
- This terminal is used to service the
transmitter.
- If you control the transmitter by
computer, you must connect a se-
rial cross cable (not supplied) from
your computer to this terminal.
INPUT 2 DIGITAL (DVI-D)
w
e
Connect DVI digital output signal
from computer to this terminal.
INPUT 3 HDMI
Connect HDMI output signal from
video equipment to this terminal.
This input is only available in the
single mode.
VENTILATION SLOT
y
Do not cover the ventilation slot
during operation.
This input cannot be selected in the
broadcast mode.
✐ -
- When selecting this input in the single
mode, the "Broadcast Mode" cannot
be selected in "Mode Select".
Note:
When you want to use the transmitter in the upright position, you
can use the supplied 2 stands. The antenna is provided near the
ventilation slot, so it is recommended to stand the transmitter as
shown in the figure for keeping the wireless communication in
good condition.
HD DATA WIRELESS TRANSMITTER BOX
1ꢁ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connection to external equipment
Cables used for connection
BNC Cable (BNC x 3)
DVI Cable
q
w
e
r
Unplug the power cords of both the
transmitter and external equipment
from the AC outlet before
HDMI Cable
Serial Control Cable
Cables are not supplied with this unit.
connecting cables.
Component Output
BNC Cable
HDMI Output
HDMI Cable
INPUT 1
INPUT 3
COMPONENT
HDMI
INPUT 2 SERIAL
DVI-D
DVI Cable
Serial Control Cable
Monitor Output Serial Control Output
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This transmitter uses nominal input
Connect the AC adaptor with following
voltages of 100–120 V or 200–240 V AC.
steps q to e.
When disconnecting, reverse the order.
✔Note:
- The AC outlet must be near this
equipment and must be easily
accessible.
- Use only the supplied AC
adaptor, and do not use any
other AC adaptor. Otherwise, a
malfunction may occur.
- Be sure to turn off the transmitter, before
disconnecting the AC power cord.
- Unplug the AC power cord when the
transmitter is not in use. When the
transmitter is connected to an outlet with
the AC power cord, it is in stand-by mode
and consumes a little electric power.
e
w
AC power cord
AC adaptor
q
DC16V 2.5A
Note on the AC Power Cord
AC power cord must meet the requirements of the country where you use the transmitter.
Confirm the AC plug type with the chart below and proper AC power cord must be used. If
the supplied AC power cord does not match your AC outlet, contact your sales dealer.
AC adapter side
AC outlet side
For Continental
Europe
For the U.S. and
Canada
For the U.K.
To the AC outlet
(120 V AC)
To the AC outlet
(200 - 240 V AC)
To the AC outlet
(200 - 240 V AC)
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the Receiver into the Projector
Part Names and Functions
q
w
Receiver
LINK INDICATOR
POWER INDICATOR
q
w
When the wireless configuration is set
up correctly and the wireless communi-
cation is established with the transmit-
ter, this indicator lights orange.
When this receiver is selected in the
projector, this indicator lights green
during operation.
Replacement of the Receiver Board
Insert the HD DATA WIRELESS Receiver
board.The cover of the board protrudes
from the cabinet of the projector.
We recommend that the HD DATA WIRE-
LESS Receiver board is inserted into the
top slot for preventing influence from
the cables of other slots.
Slot Cover or
Interface Board
✔Note:
- ꢀInꢀtheꢀeventꢀofꢀreplacementꢀofꢀinterfaceꢀ
board,ꢀturnꢀoffꢀtheꢀprojector,ꢀpressꢀtheꢀ
MainꢀOn/OffꢀSwitchꢀtoꢀOffꢀandꢀunplugꢀ
theꢀACꢀpowerꢀcordꢀfromꢀtheꢀACꢀoutlet.
Screws
Guide
Socket
1 Remove 2 Screws from an interface
board or a slot cover.
2 Pull out the interface board. or a slot
cover.
3 Insert the HD DATA WIRELESS Receiver
board along Guide to fit Plug into
Socket.
Plug
4 Tighten 2 screws to secure the HD
DATA WIRELESS Receiver board.
Screws
✐
1(one) HD DATA WIRELESS Receiver Board is available in 1(one) projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢄ
Basic Setting and Operation
Projector Operation
Turning on the Projector
1. Connect the projector’s AC power cord into an AC outlet and turn on the MAIN ON/OFF
Switch. The LAMP indicator lights red and the READY indicator lights green.
2. Press the ON/STAND-BY button on the side control or on the remote control. The LAMP
indicator dims red and the cooling fans start to operate. The preparation display appears
on the screen and the countdown starts.
3. After the countdown, the input source that was selected the last time and the Lamp
mode icon appear on the screen.
If the projector is locked with a PIN code, PIN code Input Dialog Box will appear. Enter the
PIN code.
Input Selection
1. Press the INPUT 1/2/3/4 buttons on the remote control or INPUT 1/2 or 3/4 buttons on
the side control to select the HD DATA Wireless Board. (You can also select it with Menu
operation, refer to the owner's manual of the projector.)
2. Check the status of the POWER indicator on the HD DATA Wireless Board. When the HD
DATA Wireless Board is selected correctly, the POWER indicator lights green.
Receiver
INPUT MENU
Input Menu icon
Move the pointer (red arrow) to the
input which the HD DATA Wireless
Board is inserted and press the
SELECT button.
POWER Indicator
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setting and Operation
Turning on the Transmitter
1. Complete peripheral connections before turning on the
transmitter.
2. Connect the AC power cord into an AC outlet. (see p.13) The
POWER indicator blinks red and then becomes red in stand-by
mode.
3. Press the ON/STAND-BY button. The POWER indicator
becomes green and the message "Hello HD Data Wireless"
appears on the LCD display for 4 seconds and then the input
source that was selected the last time appears on the LCD
display.
POWER indicator
Hello
HD Data Wireless
after 4 seconds
4. When the wireless communication is established with the
receiver, the LINK indicator lights up.
INPUT SIGNAL >>
[S]
XGA 1
5. If the transmitter is locked with the Key Lock function, release
Lock Key. Refer to the Key Lock function on pages 32 - 33.
✐ If the Lock Key is not entered for 3 minutes after "Input Lock Key"
appeared, the transmitter will be turned off automatically.
Input Lock Key
[#]### OK
Turning off the transmitter
1. Press the ON/STAND-BY button. The POWER indicator
becomes red and the display will disappear.
2. Unplug the AC power cord from the AC outlet.
1ꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setting and Operation
Input Source Selection
1. Choose either INPUT 1 (COMPONENT), INPUT 2 (DVI) or INPUT
3 (HDMI) by pressing the INPUT button.
INPUT button
INPUT 1
COMPONENT
2. The Indicator of the selected input lights blue.
INPUT 2
DVI
INPUT 3
HDMI
INPUT indicators
INPUT button
✐ "INPUT 3 HDMI" cannot be selected in the Broadcast Mode.
How to Operate the Menu
1. Press the MENU button to show the LCD Display.
Point button
MENU button
2. Press the Point
buttons to select a Main Menu and press
de
the SELECT button. A Sub Menu appears on the LCD Display.
3. Press the Point
de
the SELECT button.
buttons to select a Sub Menu and press
✐ Press the point button in a Sub Menu to return to a Main Menu..
7
4. Press the Point
buttons to set up or adjust the item data.
7 8
SELECT button
5. To quit the Menu, press the MENU button again and Input
Source appears on the LCD Display.
Page Number
Bracket [ ]
Examples of LCD Display
Authentication
Yes [NO]
INPUT SIGNAL >>
Image
2/6
[B]
XGA 1
Adjust
Signal Information
Menu Guide
de buttons are available.
Menu Guide
7 8 buttons are available.
Selected Mode
[B] . . . . . . in Broadcast Mode
[S] . . . . . . in Single Mode
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
1ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setting and Operation
Menu Tree
TRANSMITTER
MAIN MENU
SUB MENU
Authentication
Initialize
Single Mode
1/6
1/2
2/2
Yes/No
Yes/No
Setup
Broadcast Mode
Output Level
Select
1/6
1,2,3,4,5
1/1
Setup
2/6 Image Adjust
3/6 Information
1/2 Contrast Setting
2/2 Brightness Setting
UP/DOWN
UP/DOWN
Link On / Link Off
H freq. / V freq.
H resol. / V resol.
4/6 ID Number
ID Number
v
5/6
Key Lock
Input Lock Key
OK
1/2
Key Lock
ON/OFF
2/2 Change Lock Key
Change Lock Key
OK
OK
New Lock Key
6/6 Mode Select
Single Mode
Broadcast Mode
v "Input Lock Key" is displayed when a lock key is not set.
Single mode /
Broadcast mode
HD DATA
WIRELESS
PROJECTOR
Mode select
Authentication
Input ID
Execute / Reset
Set / Cancel
Reception level
Reset
Yes / No
Quit
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setting and Operation
Flow of Installation Mode
TRANSMITTER
PROJECTOR
Single Mode Operation
When using a pair of transmitter and receiver for the first time.
Select "Single Mode" in
"Mode Select"..
Select "Single mode" in
"Mode select".
Step 1:
Step 1:
Step 2:
Step 3:
Select "Execute" in
"Authentication".
Step 2: Execute "Authentication".
"Please wait ..." >>> Success
icon
Step 3: "Please wait ..." >>> "Success"
When changing a pair of transmitter and receiver,
Execute "Initialize" to reset
Step 1:
Select "Reset" in
"Authentication".
Step 1:
Step 2:
Step 3:
the authentication.
Select "Execute" in
"Authentication".
Step 2: Execute "Authentication".
"Please wait ..." >>> Success
icon
Step 3: "Please wait ...">>> "Success"
Broadcast Mode Operation
When using a transmitter and receivers in broadcast mode.
Select "Broadcast Mode" in
"Mode Select"..
Select "Broadcast mode" in
"Mode select".
Step 1:
Step 1:
Input the same ID Number
Step 2: Check the "ID Number".
Step 5: Adjust "Output Level".
Step 3: of the transmitter into "Input
ID".
Step 4: Check "Reception Level".
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Single Mode Operation
6/6: Mode Select & 1/6: Single Mode Setup
TRANSMITTER
When using a pair of transmitter and receiver for the first time
Select the installation mode according to the situation in which the projector is installed.
When using in the single mode, it is necessary to perform the mutual authentication be-
tween the transmitter and the receiver. Setup them side by side as described below.
Main Menu 6/6: Mode Select
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu 6/6: Mode Select and then press the SELECT button.
2. Press the Point buttons to select the Single Mode.
7 8
3. Input signal will be displayed [S] in the lower left-hand corner.
Mode
6/6
Single
Mode
INPUT SIGNAL >>
Select
[S]
XGA 1
Broadcast
Mode
Main Menu 1/6: Single Mode Setup
a Sub Menu 1/2: Authentication
1. Press the MENU button to show the Menu. Press the Point
button to select Main
de
Menu 1/6: Single Mode Setup and then press the SELECT button.
2. Press the Point
SELECT button.
buttons to select Sub Menu 1/2: Authentication and then press the
de
3. Press the Point
buttons to move the bracket to [YES] and then press the SELECT
7 8
button to perform the authentication.
4. The message "Please wait ..." will be displayed and the transmitter is waiting for the
response from the receiver.
5. Set up the authentication of the receiver.
6. If the authentication is completed, the message "Success" will be displayed for 5 seconds
and the LINK indicator lights orange.
If it is not completed within about 5 minutes, the message "Failure" will be displayed for
5 seconds.
Authentication
YES [NO]
SingleMode 1/6
Authenti- 1/2
cation
ꢀꢀꢀꢀꢀꢀꢀ
Setup
Authentication
[YES] NO
Success
Failure
Please wait...
✐
If you press Menu button during authentication, the authentication will be cancelled.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Single Mode Operation
PROJECTOR
Mode select
1. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to
move the red frame pointer to the HD DATA WIRELESS icon.
2. Use the Point de buttons to move the
red frame pointer to the Mode Select
icon and then press the SELECT button
twice. A dialog box appears.
Mode Select Menu
3. Use the Point de buttons to select
Single mode and then press the SELECT
button.
Authentication
1. Use the Point de buttons to move the red frame pointer to the Authentication icon
and then press the SELECT button. A dialog box appears.
2. Use the Point de buttons to select
Execute and then press the SELECT
Authentication Menu
button. The receiver starts to establish
communication with the transmitter.
The message "Please wait ..." will be
displayed until the establishment.
3. Set up the authentication of the
transmitter.
4. If the authentication is completed, the
Success icon will be displayed for 4
seconds.
If it is not completed within about
5 minutes, the Failure icon will be
displayed for 4 seconds. Please check
the settings of the transmitter or the
receiver.
Success icon
Failure icon
5. When the communication is established,
the LINK indicator lights orange.
✐
If you press any button on the projector or the remote control during authentication, the
authentication will be cancelled.
HD DATA WIRELESS TRANSMITTER BOX
ꢀꢁ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Single Mode Operation
TRANSMITTER
When changing a pair of transmitter and receiver
If you want to communicate with the other receiver, you should reset the current
authentication.
Main Menu 6/6: Mode Select
If not set to the Single Mode, set to the Single Mode. Refer to page 22.
Main Menu 1/6: Single Mode Setup
a Sub Menu 2/2: Initialize
1. Press the MENU button to show the Menu. Press the Point
button to select Main
de
Menu 1/6: Single Mode Setup and then press the SELECT button.
2. Press the Point
SELECT button.
buttons to select Sub Menu 2/2: Initialize and then press the
de
3. Press the Point
buttons to move the bracket to [YES] and then press the SELECT
7 8
button to perform the initialization.
SingleMode 1/6
Initialize 2/2
Initialize
[YES] NO
ꢀꢀꢀꢀꢀ
Setup
Main Menu 1/6: Single Mode Setup
a Sub Menu 1/2: Authentication
Perform the Authentication again. Refer to page 22.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Single Mode Operation
PROJECTOR
Mode select
If not set to the Single mode, set to the Single mode. Refer to page 23.
Authentication
1. Use the Point de buttons to move the red frame pointer to the Authentication icon
and then press the SELECT button. A dialog box appears.
2. Select Reset and then press the SELECT
button. The authentication will be reset.
Authentication Menu
Authentication
Perform the Authentication again. Refer to page 23.
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadcast Mode Operation
Select the installation mode according to the situation in which the projector is installed.
When using in the broadcast mode, it is necessary to set up the ID number into the receiver
which is conformed to that of the transmitter.
Setup them side by side as described below.
6/6: Mode Select & 4/6: ID Number
TRANSMITTER
Main Menu 6/6: Mode Select
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu 6/6: Mode Select and then press the SELECT button.
2. Press the Point
orange.
buttons to select the Broadcast Mode. The LINK indicator lights
7 8
3. Input signal will be displayed [B] in the lower left-hand corner.
Mode
6/6
Single
Mode
Select
Broadcast
Mode
INPUT SIGNAL >>
[B]
XGA 1
Main Menu 4/6: ID Number
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu 4/6: ID Number and then press the SELECT button.
2. An eight-digit ID Number will be displayed. Note it and set up the same ID number in
the projector.
ID Number 4/6
ID Number
****-****
3. Press the MENU button to exit this Menu.
✐ When selecting "INPUT 3 HDMI" in Single Mode, Broadcast Mode cannot be selected..
✐ ID Number characters : 0 to 9, A to F
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadcast Mode Operation
PROJECTOR
Mode select
1. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to
move the red frame pointer to the HD DATA WIRELESS icon.
2. Use the Point de buttons to move the
Mode Select Menu
red frame pointer to the Mode Select
icon and then press the SELECT button
twice. A dialog box appears.
3. Use the Point de buttons to select
Broadcast mode and then press the
SELECT button.
Input ID
1. Before inputting the ID Number, check
the ID Number in the transmitter.
Input ID Menu
2. Use the Point
buttons to select
de
Input ID and then press the SELECT
button.
3. Input the ID Number as follows;
Select a number by pressing the Point
buttons. And then press the Point
de
button to fix the number and move
8
the pointer. If you fixed the incorrect
number, move the pointer to the
number you want to correct by pressing
the Point button, and then select the
7
correct number by pressing the Point
buttons.
de
4. Repeat this step to complete entering an
eight-digit number.
5. After entering the eight-digit number,
move the pointer to "Set" by pressing
the Point button. Press the Select
8
button to continue.
6. Confirmation box appears, select [Yes] to
confirm the ID Number.
✐ Once authenticated in Single mode, the ID Number of the transmitter which has been set in Single
mode will be displayed as a default. When switching from Single mode to Broadcast mode, change the
ID Number to the new one of the transmitter.
HD DATA WIRELESS TRANSMITTER BOX
ꢀꢅ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadcast Mode Operation
TRANSMITTER
1/1: Output Level Select
Noise or interference may appear on images of some projectors when using in the
broadcast mode depending on whether the signal reception level of receiver is too high or
low. Try to adjust the output level of the transmitter to get the best reception condition for
all projectors.
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu "1/6: Broadcast Mode Setup" Menu and then press the SELECT button.
2. Press the Point
buttons to select Sub Menu "1/1: Output Level Select" and then
de
press the SELECT button.
3. Press the Point
buttons to select the Output Level (1 to 5) and then press the
7 8
SELECT button to perform the adjustment.
1 . . . . . .minimum output level
5 . . . . . .maximum output level
Broadcast 1/6
Mode Setup
Output
1/1
Output Level
1
Level Select
Output Level
5
ꢀꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadcast Mode Operation
PROJECTOR
Reception Level
1. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to
move the red frame pointer to the HD DATA WIRELESS icon.
Reception Level Menu
2. Use the Point de buttons to move the
red frame pointer to Reception level
icon and then press the SELECT button.
3. The Reception Level (0 to 7) display
appears.
0. . . . . . minimum reception level
7. . . . . . maximum reception level
Reception Level
4. If necessary, try to adjust the output
level of the transmitter.
Level 7
5. When any button is pressed on the
side panel or the remote control, the
Level 5 (Level 5 to 7 = green)
reception level disappears.
Level 3 (Level 3 to 4 = yellow)
Level 1 (Level 1 to 2 = red)
Level 0 ( = white)
HD DATA WIRELESS TRANSMITTER BOX
ꢀꢇ
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Basic Operation
5/6: Key Lock
TRANSMITTER
This function allows you to lock the key operation on the transmitter.
To enter a new Lock Key
At first, set up a new Lock Key in the transmitter to operate Key Lock function.
"Input Lock Key [#]### OK"
✐ If a Lock Key is already set, this menu
will not be displayed.
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu "5/6: Key Lock" and then press the SELECT button. "Input Lock Key [#]### OK"
will be displayed.
2. Use the Point
buttons to enter a number (0 ~ 9). Press the Point button to fix the
ed
8
number and move to the next box.
3. Repeat this step to complete entering a four-digit number.
4. Press the Point
button.
buttons to move the bracket to [OK] and then press the SELECT
7 8
5. "1/2: Key Lock" will be displayed.
Key Lock 5/6
Input Lock Key
[#]### OK
Input Lock Key
#### [OK]
Key Lock 1/2
To set Key Lock
1. While Sub Menu "1/2: Key Lock" is displayed, press the SELECT button. "Key Lock ON
[OFF]" will be displayed.
2. Move the bracket from [OFF] to [ON] by pressing the Point
the SELECT button.
buttons and then press
7 8
2. "Key Lock" will be displayed.
3. While Key Lock is set to ON, when any button is pressed, "Input Lock Key #### OK" will
be displayed.
Key Lock 1/2
Key Lock
ON [OFF]
Key Lock
[ON] OFF
Key Lock
Input Lock Key
[#]### OK
✐ Even when the AC power was shutdown, the key lock function is still available. If the transmitter is
locked with a lock key, "Input Lock Key" appears at turning on the transmitter. If the Lock Key is not
entered for 3 minutes after "Input Lock Key" appeared, the transmitter will be turned off automatically.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Basic Operation
TRANSMITTER
To change Lock Key
1. Press the MENU button to show the Menu. Press the Point
Menu "5/6: Key Lock" and then press the SELECT button.
buttons to select Main
de
2. Press the Point
buttons to select Sub Menu "2/2: Change Lock Key" and then press
de
the SELECT button.
3. Enter the current four-digit number. Use the Point
buttons to enter a number. Press
ed
the Point button to fix the number and move to the next box.
8
4. Press the Point
button.
buttons to move the bracket to [OK] and then press the SELECT
7 8
5. "New Lock Key" will be displayed. Enter a new four-digit number.
6. Press the Point
button.
buttons to move the frame to [OK] and then press the SELECT
7 8
Key Lock 5/6
Change
2/2
Change Lock Key
[#]### OK
Lock Key
New Lock Key
[#]### OK
To release Lock Key
1. Press a button on the transmitter. "Input Lock Key" will be displayed.
2. Enter the current four-digit number, the Lock Key will be released and you can operate
the transmitter.
Menu Tree of Key Lock
Key Lock 5/6
Input Lock Key
[#]### OK
Input Lock Key
#### [OK]
Key Lock 1/2
Key Lock
ON [OFF]
Key Lock
[ON] OFF
Key Lock
Input Lock Key
[#]### OK
Change
2/2
Change Lock Key
[#]### OK
New Lock Key
[#]### OK
Lock Key
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Basic Operation
2/6: Image Adjust
TRANSMITTER
You can adjust contrast and brightness of the output signal from the transmitter.
1. Press the MENU button to show the Menu. Press the Point
buttons to select Main
de
Menu "2/6: Image Adjust" and then press the SELECT button.
Contrast 1/2
Setting
Contrast
+32
Image
2/6
Adjust
Brightness 2/2
Setting
Brightness
-32
1/2: Contrast Setting
After the step 1;
2. Press the Point
buttons to select Sub Menu "1/2: Contrast Setting" and then press
de
the SELECT button.
3. Press the Point
buttons to adjust the contrast (-32 to +32).
7 8
2/2: Brightness Setting
After the step 1;
2. Press the Point
buttons to select Sub Menu "2/2: Brightness Setting" and then
de
press the SELECT button.
3. Press the Point buttons to adjust the brightness (-32 to +32).
7 8
3/6: Information
Information display can be used to confirm the current output signal from the transmitter.
1. Press the MENU button to show the Menu. Press the Point
de
Menu "3/6 Information" and then press the SELECT button.
buttons to select Main
2. The information "Link On / RF Frequency", "Link Off RF Frequency", "H/V Frequency"
and "H/V Resolution" will be displayed periodically.
Information 3/6
Link On
Link Off
or
RF Freq. ****MHz
RF Freq. ****MHz
H Freq. ****
V Freq. ****
H Resol. ****
V Resol. ****
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Basic Operation
Reset Function of the projector
PROJECTOR
Reset
1. Press the MENU button to display the
Reset Menu
On-Screen Menu. Use the Point 7 8
buttons to move the red frame pointer
to the HD DATA WIRELESS icon.
2. Use the Point de buttons to select
Reset and the “Return to Wireless
factory default?”appears. Select [Yes] to
continue.
3. Another confirmation dialog box
appears, select [Yes] to reset the Wireless
setting of Mode select, Input ID and
Authentication.
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Cleaning the cabinet
Turn off the transmitter and unplug the AC power cord from the AC outlet before cleaning.
Gently wipe the transmitter body with a soft dry cleaning cloth. When the cabinet is heavily
soiled, use a small amount of mild detergent and finish with a soft dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals
might scratch the surface of the cabinet.
Indicators
When the transmitter detects an abnormal condition, it is automatically shut down to
protect the inside of the transmitter and three INPUT indicators and LINK indicator start
blinking. In this case, unplug the AC power cord and reconnect it, and then turn the
transmitter on once again to verify operation. If the transmitter cannot be turned on,
unplug the AC power cord and contact the service station.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
- Make sure you have properly connected the transmitter to peripheral equipment.
- Make sure all equipment is connected to the AC outlet and the power is turned on.
Problem
Solutions
No power
-
-
Plug the AC power cord into the AC outlet.
Check the connection of the AC adaptor and try to
re-connect the AC adaptor.
-
-
-
Check the LINK indicator.
No image
Check the authentication in the single mode.
Check both ID numbers in the transmitter and the
projectors in the broadcast mode.
Check the compatible signals of the transmitter. (see
p.38)
-
-
-
Check the reception level of the projectors.
Try to increase the output level in the broadcast
mode.
Poor (noisy) Image
-
-
Make sure there is no obstruction between the
transmitter and the projector.
Try to move the transmitter or the projector.
Maximum operation range is within about 30 m.
Block-noise of Images
-
Try to adjust the output level in the broadcast
mode.
-
-
Try to move the transmitter or the projector.
When the transmitter detects an abnormal
condition, three INPUT indicators and LINK indicator
blinks. In this case, unplug the AC power cord and
reconnect it, and then turn the transmitter on once
again to verify operation. If the transmitter cannot
be turned on, unplug the AC power cord and
contact the service station.
Some Indicators are blinking.
Buttons do not work.
Key Lock Number is required at
start-up.
-
-
Unlock the key lock function.
The key lock function is being set. Enter the 4-digit
number you have set.
Unable to select INPUT 3(HDMI)
-
-
When using the broadcast mode, HDMI cannot be
selected.
Unable to select the secondary
HD DATA WIRELESS Receiver
Board.
1(one) HD DATA WIRELESS Receiver Board is
available in 1(one) projector. When using multiple
HD DATA WIRELESS Receiver Boards, only a slot with
the smallest number is available for use.
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Interface
Component Input Jacks
Computer Digital Input Jack
HDMI Input Jack
DC IN Jack
BNC Type x 3
DVI-D Terminal x 1
HDMI Terminal x 1
DC 16 V (AC Adaptor)
Power
Voltage
100 - 120 V or 200 - 240V, 50/60 Hz
DC 16V 1.0A
11.8 [W] at normal, 2.43 [W] at stand-by mode
Power Consumption
Operating Environment
Operating Temperature
Storage Temperature
Mechanical Information
Dimensions ( W x H x D )
Net Weight
41ºF - 95ºF (5ºC - 35ºC)
14ºF - 140ºF (-10ºC - 60ºC)
10.63" x 1.97" x 8.66" (270 x 50 x 220 mm)
2.87 lbs (1.3 kg)
Wireless Information
Interface
IEEE802.11a/n
AdHoc
Communication Mode
US
EU
5.18, 5.20, 5.22, 5.745, 5.765, 5.785, 5.805, 5.825 GHz
5.18, 5.20, 5.22 GHz
Wireless Frequency
Modulation Form
Security
IEEE802.11a OFDM
256bit AES
about 98' (30 m) (line-of-sight without disturbance)
Differs according to the operating environment.
Service area
✐ The specifications are subject to change without notice.
ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compliance
JAPAN: VCCI Class A, TELEC (Wireless)
USA: FCC Part15 Subpart C (Wireless)
FCC Part15 Subpart C, Class A
Countries and Standards
Canada: IC RSS-210 (Wireless), IC ICES-003 Class A
Europe: R&TTE, EMC, LVD
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Signals Specifications
H-Freq.
[kHz]
V-Freq.
[Hz]
LCD
DISPLAY
TERMINAL
SIGNAL
RESOLUTION
INPUT 1 : COMPONENT
INPUT 3 : HDMI
480p
575p
31.47
31.25
37.50
45.00
28.125
33.75
31.47
37.88
43.363
47.776
41.20
59.88
50.00
50.00
60.00
50.00
60.00
59.94
60.32
60.00
59.87
50.00
480p
575p
720p - 50
720p - 60
1080i - 50
1080i - 60
VGA 1
720p
720p
1080i
1080i
INPUT 2 : DVI-D
640 x 480
800 x 600
1024 x 768
1280 x 768
1280 x 800
VGA 1
SVGA 2
XGA 1
WXGA 6
WXGA 10
SVGA 2
XGA 1
WXGA 6
WXGA 10
ꢁꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configurations of Terminals
INPUT 2 : DIGITAL DVI-D (DVI 24 Pin)
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
No Connect
DDC Clock
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
No Connect
+5V Power
T.M.D.S. Data0–
1
2
3
4
5
6
7
8
9
17
18
19
20
21
22
23
24
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
10
11
12
13
14
15
16
No Connect
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
DDC Data
No Connect
Ground (for +5V)
Hot Plug Detect
INPUT 3 : HDMI (19 PinType A)
1
2
3
4
5
6
7
8
9
11
TMDS Data 2+ Input
Ground (TMDS Data 2)
TMDS Data 2- Input
TMDS Data 1+ Input
Ground (TMDS Data 1)
TMDS Data 1- Input
TMDS Data 0+ Input
Ground (TMDS Data 0)
TMDS Data 0- Input
TMDS Clock+ Input
Ground (TMDS Clock)
TMDS Clock- Input
No Connect
No Connect
SCL
12
13
14
15
16
17
18
19
1
3
5
7
9
11 13 15 17 19
10 12 14 16 18
2
4
6
8
SDA
Ground (DDC/CEC)
+5V Power
Plug insert detection
10
SERIAL CONTROL PORT (Mini D-sub 9 pin)
Serial
No Connect
R X D
T X D
No Connect
SG
1
2
3
4
5
6
7
8
9
No Connect
RTS
CTS
No Connect
HD DATA WIRELESS TRANSMITTER BOX
OWNER'S MANUAL
ꢁꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S MANUAL POA-HDTM01
1AA6P1P5524-- (IFFZ)
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|