Multimedia Projector
MODEL PLC-XP57L
✽ Projection lens is optional.
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCE
Federal Communication Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: PLC-XP57L
: Sanyo
: SANYO FISHER COMPANY
: 21605 Plummer Street, Chatsworth, California 91311, U.S.A.
Telephone No.
: (818)998-7322
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of
the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating,
ASA
marked thus
. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover
is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers
are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
COMPUTER INPUT
24
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
24
25
PREPARATION
7
PC ADJUSTMENT
26
26
27
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
NAME OF EACH PART OF PROJECTOR
7
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
LENS INSTALLATION
8
PICTURE IMAGE SELECT
29
8
IMAGE LEVEL SELECT
29
9
PICTURE SCREEN ADJUSTMENT
30
30
ADJUSTABLE FEET
INSTALLING PROJECTOR IN PROPER POSITION
MOVING PROJECTOR
10
10
11
PICTURE SCREEN SELECT
VIDEO INPUT
31
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
31
32
CONNECTING PROJECTOR
12
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTERS
CONNECTING TO VIDEO EQUIPMENT
12
13
14
PICTURE IMAGE SELECT
33
IMAGE LEVEL SELECT
33
PICTURE SCREEN ADJUSTMENT
34
34
PICTURE SCREEN SELECT
BEFORE OPERATION
15
PICTURE IMAGE
35
REMOTE CONTROL OPERATION
LASER POINTER FUNCTION
15
15
16
PICTURE IMAGE ADJUSTMENTS
35
REMOTE CONTROL BATTERIES INSTALLATION
SETTING
38
TOP CONTROLS AND INDICATORS
ON-SCREEN MENU
17
18
18
18
19
SETTING MENU
38
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
APPENDIX
45
WIRELESS MOUSE
MAINTENANCE
45
BASIC OPERATION
20
46
46
47
47
WARNING TEMP. INDICATOR
AIR FILTERS CARE AND CLEANING
CLEANING PROJECTION LENS
TURNING ON/OFF PROJECTOR
TURNING ON THE PROJECTOR
TURNING OFF THE PROJECTOR
20
20
21
LAMP REPLACEMENT
48
49
ADJUSTING SCREEN
ZOOM ADJUSTMENT
22
22
22
22
22
23
23
23
LAMP REPLACE COUNTER
TROUBLESHOOTING
50
52
54
55
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE CORRECTION
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
P-TIMER FUNCTION
MENU TREE
COMPATIBLE COMPUTER SPECIFICATIONS
INDICATORS AND PROJECTOR CONDITION
TECHNICAL SPECIFICATIONS
CONFIGURATIONS OF TERMINALS
OPTIONAL PARTS
57
58
59
59
59
60
61
SOUND ADJUSTMENT
23
LENS REPLACEMENT
PJ LINK NOTICE
PIN CODE NUMBER MEMO
DIMENSIONS
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD)
technology.
◆ Compact Design
◆ Digital Zoom (for Computer)
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.
Digital Zoom function adjusts image size to approx.
1/4–49 times of an original image size, allowing you to
focus on a crucial information at the presentation.
◆ Compatibility
◆ Keystone Correction
This projector widely accepts various video and
computer input signals such as:
Positioning of the projector may result in distorted image
being displayed in a trapezoid shape. Keystone function
solves this problem by digitally altering the projection to
produce undistorted images.
● Computers
IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.
◆ Power Management
● 6 Color Systems
Power management function is provided to reduce power
consumption when the projector is not in use.
NTSC, PAL, SECAM, NTSC 4.43, PAL-M, or PAL-
N color system can be connected.
The Power management function operates to turn the
projection lamp off when the projector detects a signal
interruption or when no button is pressed for a certain
period. The projection lamp is automatically turned on
again when the projector detects a signal or any
operation button is pressed.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, or 1080i, can be
connected.
● S-Video
This projector is shipped with this function ON.
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
◆ Digital Visual Interface
◆ High Resolution Image
This projector is equipped with the DVI 24-pin terminal
for connecting DVI output from a computer.
This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer with more than XGA (1024 x 768) is
compressed into 1024 x 768 dots. This projector cannot
display image of over 1920 x 1080 dots. When resolution
of your computer is over 1920 x 1080, lower the
resolution for a computer output.
◆ Laser Pointer Function
Remote control supplied with this projector includes the
Laser Pointer function. This function helps you to make a
smart presentation on a projected screen.
◆ Wireless Mouse
◆ Multi-Scan System
Remote control supplied with this projector has the
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with the remote control only.
This projector has the Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for a troublesome manual adjustment of frequency
and other settings.
◆ Multilanguage Menu Display
◆ One-Touch Auto PC Adjustment
Operation menu is available in 12 languages: English,
German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean, or Japanese.
Incoming computer video signals are recognized and the
best adjustment is automatically set by the Auto PC
Adjustment function. No complicated setup is necessary
and the projection is always precise.
◆ PJ-Net Organizer (Optional)
PJ-Net Organizer enables the projector to display the
image of the computer screen and the image data stored
in the computer via a network. The projector can also be
controlled and maintained through a web browser.
◆ Motor-driven Lens Shift
Projection lens can be moved up and down with the
motor-driven lens shift function. This function makes it
easy to provide projected image where you want.
Zoom and focus can also be adjusted with a motor-
driven operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
SPEAKERS
FRONT OF CABINET
TOP CONTROLS
AND INDICATORS
PROJECTION LENS ✽
Kensington Security Slot
This slot is for a Kensington
lock used to deter theft of
the projector.
✽ optional
CAUTION
* Kensington is a registered
trademark of ACCO Brands
Corporation.
Do not turn on the projector with
the lens cap attached. High
temperature from light beam
may damage the lens cap and
result in fire hazard.
AIR INTAKE
VENT
INFRARED
REMOTE RECEIVER
BACK OF CABINET
POWER CORD
CONNECTOR
TERMINALS
AND CONNECTORS
INFRARED
REMOTE RECEIVER
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot.
When using or installing the projector, the
following precautions should be taken.
● Do not put a flammable object near this vent.
● Keep the rear grills at least 3.3’ (1 m) away
from any object, especially from heat-
sensitive objects.
● Do not touch this area, especially screws
and metallic parts. This area will become hot
when the projector is in use.
CARRYING
HANDLE
LAMP COVER
This projector detects internal temperature
and automatically controls operating power
of the cooling fans.
When attaching the PJ-Net Organizer
(optional) to the projector, remove the these
parts. Refer to the owner's manual of the
optional PJ-Net organizer.
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protecting from
overheating. Pay attention to the following matters to ensure
proper ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slots.
● Keep this side clear of any objects. Obstructions may block
cooling the air.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100–120 V or
200–240 V AC and it automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning
it on. (See pages 12–14 for connection.)
CAUTION
For safety, unplug the AC power cord when the projector is not
in use. When the projector is connected to an outlet with AC
power cord, an appliance is in stand-by mode and consumes a
little electric power.
Connect AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and
must be easily accessible.
NOTE ON POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and a proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada For Continental Europe
For the U.K.
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(200–240 V AC)
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200–240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
LENS INSTALLATION
Before setting up the projector, install a projection lens on
the projector.
1. Before installation, check the area where the projector is
used and prepare a suitable lens. For the specifications of
a projection lens, contact sales dealer where you
purchased the projector.
COVER CAP
2. For installation, refer to the installation manual of the
optional lens.
NOTE:
• When installing the lens, remove the cover cap of the projector.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ADJUSTABLE FEET
Projection angle can be adjusted up to 10.5 degrees with the
ADJUSTABLE FEET.
Lift the front of the projector and pull the FEET LOCK
LATCHES in each side of the projector.
1
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to a
proper height, and tilt.
2
To retract the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
3
Keystone distortion of the projected image can be corrected
by the Menu Operation. (See pages 22, 38.)
ADJUSTABLE FEET
FEET LOCK
LATCHES
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.
10˚
Do not tilt the projector more than 10 degrees from side to side.
10˚
Do not put the projector on either side to project an image.
NO SIDEWAYS
10˚ 10˚
When projecting vertically (up or down), keep the projector’s tilt within 10 degrees.
Tilting more than 10 degrees in either direction may affect the projector life.
10˚ 10˚
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING PROJECTOR
Use the Carrying Handle when moving the projector.
Replace the lens cap and retract the ADJUSTABLE FEET
when moving the projector to prevent damages to the lens
and cabinet.
When this projector is not in use for an extended period, put
it into a suitable case (not supplied with this projector).
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
● Do not drop or bump the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a suitable carrying case.
● Do not transport the projector by courier or any other transport service in an unsuitable transport case.
This may cause damage to the projector. To transport the projector by courier or any other transport
service, consult your dealer for the best way.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer
to the figures on pages 12–14 and connect properly.
COMPUTER INPUT/MONITOR
OUTPUT TERMINAL (ANALOG)
COMPUTER INPUT
TERMINAL (DIGITAL)
COMPUTER AUDIO
INPUT 2 JACK
COMPUTER AUDIO INPUT 1/
AUDIO MONITOR OUTPUT
JACK
This terminal is switchable and
can be used as Computer Input
or Monitor Output. Set up the
terminal as either Computer Input
or Monitor Output properly before
using this terminal.
Connect a computer output Connect an audio
(Digital DVI-D type) to this output (stereo) from a
terminal.
The HD (HDCP Compatible) (See page 13.)
signal can also be connected.
(See page 13.)
This terminal is switchable and
can be used as Computer
Audio Input 1 or Audio Monitor
Output (variable).
Set up the terminal as either
Computer Audio Input 1 or
Audio Monitor Output properly
before using this terminal.
(See pages 13, 24.)
computer to this jack.
(See pages 13–14, 24.)
Note: This terminal outputs from the
5 BNC type computer input on
INPUT 2 jacks only.
Note: This terminal does not
output audio from INPUT 3.
R/C JACK
When using the Wired/Wireless
remote control as wired,
connect the Wired remote
control to this jack with a
remote control cable (optional).
USB CONNECTOR (Series B)
When controlling a computer
with the remote control of this
projector, connect USB terminal
of your personal computer to
this terminal. (See page 13.)
CONTROL PORT CONNECTOR
When controlling a computer
with the remote control of this
projector, connect the mouse
port of your personal computer
to this connector.
RESET BUTTON
This projector uses
a
micro
processor to control the unit, and
only occasionally, this micro
processor may malfunction and
need to be reset. This can be done
by pressing the RESET button with
a pen, which will shut down and
restart the unit. Do not use the
RESET function excessively.
(See page 13.)
VIDEO INPUT JACKS
AUDIO INPUT JACKS
S-VIDEO INPUT JACK
Connect composite video Connect an audio output Connect S-VIDEO
output from video equipment from video equipment to output from video
5 BNC INPUT JACKS
to VIDEO/Y jack or connect these jacks.
component video outputs to (See page 14.)
VIDEO/Y, Cb/Pb and Cr/Pr
equipment to this
jack. (See page 14.)
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync, and
Vert. Sync.)} from computer to
G, B, R, H/V, and V jacks.
(See pages 13, 14.)
jacks. (See page 14.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTERS
Cables used for connection (✽ = Cables or adapters not supplied with this projector.)
• VGA Cable (HDB 15 pin)
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• BNC Cable ✽
• Control Cable for PS2 Port ✽, or ADB Port ✽
• USB Cable
• Audio Cables (Mini Plug [stereo] x 2) ✽
• Control Cable for Serial Port
IBM-compatible computer or Macintosh computer (VGA/SVGA/XGA/SXGA/SXGA+/WXGA/UXGA )
Desktop type
Laptop type
Monitor Output
or
Monitor Output
Monitor Output USB port
Audio Output Serial port
PS/2 port
ADB port
Monitor Input
Control Cable
for Serial Port
Control Cable Control Cable
for PS/2 Port ✽ for ADB Port ✽
USB
Cable
Audio
Cable ✽
(stereo)
DVI
Cable ✽
VGA Cable
Terminal
Terminal
Terminal
BNC
Cable ✽
COMPUTER
AUDIO IN 1 or 2
Use one of these control
cables corresponding to the
terminal of your computer.
USB
COMPUTER IN ANALOG
COMPUTER IN DIGITAL
CONTROL
PORT
INPUT 1
DIGITADVI-D)
ANALOIN/OUT
R/C JACK
NOTE:
This terminal is switchable. Set up
the terminal as either Computer
Audio Input 1 or Audio Monitor
Output (variable) before using this
terminal. (See page 24.)
CONTRL PORT
RESET
UB
AUDIO 1
IN/OUT
AUDIO 2
NOTE:
This terminal is switchable.
Set up the terminal as either
Computer input or Monitor
output before using this
terminal.(See page 24.)
AUDIO OUT
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
Audio Cable
(stereo) ✽
(
)
MONO
INPUT 3
Terminals
of the Projector
Audio Input
External Audio Equipment
NOTE:
Audio Speakers
(stereo)
Unplug the power cords of both the projector and
external equipment from the AC outlet before
connecting cables. Turn a projector and peripheral
equipment on before computer is switched on.
Audio Amplifier
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection (✽ = Cables not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• Audio Cable (Mini Plug [stereo]) ✽
• Scart Cable ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x 2) ✽
Video Source (Example)
Video Cassette Recorder
Component video output equipment.
(such as DVD players or high-definition TV sources.)
Video Disc Player
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
RGB Scart
21-pin Output Video Output
Composite
Composite
Video Output
S-VIDEO
Output
Audio Output Audio Output
Video Cables
(RCA x 1 or
Scart Cable ✽
RCA x 3) ✽
Audio
Audio Cable
S-VIDEO
Cable ✽
(stereo)
(RCA x 2) ✽
Cable ✽
BNC Cable ✽
Y - Cb/Pb - Cr/Pr
Y - Cb/Pb - Cr/Pr
VIDEO
VIDEO
AUDIO IN
AUDIO IN
S-VIDEO
COMPUTER IN ANALOG
AUDIO OUT
Audio Cable
(stereo) ✽
NOTE:
This terminal is switchable.
Set up the terminal as either
Computer input or Monitor
output before using this
terminal.(See page 24.)
Terminals
of the Projector
Audio Input
External Audio Equipment
NOTE:
Audio Speakers
(stereo)
Unplug the power cords of both the projector and
external equipment from the AC outlet before
connecting cables.
Audio Amplifier
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
REMOTE CONTROL OPERATION
LASER POINTER
(DRAG ON) INDICATOR
Left Side
POWER ON-OFF BUTTON
Used to turn the projector on
or off. (p.20, 21)
Lights red while the laser
beam is emitted from the
Laser Light Window.
Lights green when dragged
to the “ON” position. (p.45)
AUTO PC ADJ. BUTTON
Use to operate the AUTO PC
Adjustment function. (p.26)
MUTE BUTTON
Used to mute the sound.
(p.23)
IMAGE BUTTON
Used to select the image
level. (pp.29, 33)
DRAG ON/OFF BUTTON
Used to select the DRAG
ON/OFF position. (p.45)
ALL OFF SWITCH
When using the remote control, turn
this switch to “ON.” And turn it to
“ALL OFF” when it is not in use.
KEYSTONE BUTTON
Used to correct keystone
distortion. (pp.22, 38)
LEFT CLICK BUTTON
INSIDE THE BATTERY
COMPARTMENT BOX
Used as a PC mouse in
Wireless Mouse Operation.
Press this button and the
mouse pointer button to drag
the selected screen object.
(p.45)
MOUSE POINTER
Used as a PC mouse in
Wireless Mouse Operation.
(p.45)
This Remote Control provides the DIP
switches into the battery compartment
box.
Slide the SW4 (LASER ON/OFF
switch) to the “OFF” position. The
Laser Pointer function is not operated.
Set the Switches 1–3 as shown in table
below depending on the Code No. that
you want to select as the remote
control code. (See page 41.)
RIGHT CLICK BUTTON
LASER BUTTON
Used as a PC mouse in
Wireless Mouse Operation.
(p.45)
Used to operate the Laser
Pointer function. The laser
beam is emitted when
pressing this button for one
minute.
When using the Laser Pointer
for more than one minute,
release this button and press
it again.
LENS SHIFT BUTTON
Used to select the Lens Shift
function. (p.22)
DIP SWITCH SETTING
SW4 ........ LASER ON/OFF
SW1 SW2 SW3 Code No.
WIRED REMOTE JACK
ON
ON
ON
ON
ON
OFF ON
ON
Code 1
Code 2
Code 3
When using as
a
Wired
OFF
Remote Control, connect a
remote control cable (not
supplied) to this jack.
FOCUS BUTTON
Used to adjust focus. (p.22)
ON
OFF OFF
Code 4
Code 5
Code 6
Code 7
Code 8
OFF ON
OFF ON
ON
OFF
Battery installation is required
OFF OFF ON
OFF OFF OFF
when using as
Remote Control.
a
Wired
LASER POINTER FUNCTION
This remote control emits laser beam from the Laser Light Window when used as a Laser Pointer. When the
LASER button is pressed, the laser light goes on. When the LASER button is being pressed for more than one
minute or it is released, the light goes off. The LASER POINTER INDICATOR lights RED and LASER is emitted
with RED light to indicate the laser beam is being emitted.
The Laser emitted is the Cass II laser. Do not look into the Laser Light Window or shine laser beam onto yourself
or other people. The three marks shown below are caution labels for the laser beam.
CAUTION: Use of controls, adjustments, or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
These caution labels are put on the remote control.
LASER POINTER INDICATOR
LASER LIGHT WINDOW
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
D.ZOOM BUTTON
Operating Range
Used to select the
DIGITAL ZOOM +/– mode
and resize the image.
(p.30)
Point the remote control toward
the projector (a Receiver
Window) when pressing any
button. Maximum operating
range for the remote control is
about 16.4’ (5 m) and 60° in front
and rear of the projector.
NO SHOW BUTTON
Used to turn the picture
into a black image. (p.23)
SELECT BUTTON
FREEZE BUTTON
Used to freeze the picture.
(p.23)
Used to execute the
selected item, or expand/
compress the image in the
DIGITAL ZOOM +/- mode.
(p.30)
POINT (VOLUME +/-)
BUTTONS
Used to select an item or
adjust a value in On-Screen
Menu. They are also used to
pan the image in the
DIGITAL ZOOM +/- mode.
(p.30)
60°
MENU BUTTON
Used to select the MENU
Operation. (pp.18, 19)
The POINT LEFT/ RIGHT
buttons are also used as
VOLUME +/- buttons. (p.23)
16.4’
(5 m)
P-TIMER BUTTON
Used to operate the P-
TIMER function. (p.23)
INPUT 1 BUTTON
Used to select an input
source (INPUT 1). (p.24)
INPUT 2 BUTTON
ZOOM BUTTON
Used to adjust zoom.
(p.22)
Used to select an input
source (INPUT 2).
(pp.25, 31)
16.4’
(5 m)
INPUT 3 BUTTON
Used to select an input
source (INPUT 3). (p.31)
COLOR MANAGEMENT
BUTTON
Used to operate the Color
management function.
(pp.35–36)
60°
NETWORK BUTTON
Used to select a network
input (optional).
REMOTE CONTROL BATTERIES INSTALLATION
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the compartment lid.
1
2
3
Two AA size batteries
Press the lid downward
and slide it.
For correct polarity (+ and
–), be sure battery terminals
are in contact with pins in
the compartment.
To insure safe operation, please observe following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture, or heat.
● Do not drop the remote control.
● If a battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to batteries manufacturers instructions and local rules.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
LAMP REPLACE INDICATOR WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns to yellow when the Blinks red when the internal Lights green when the Becomes dim when the
projection lamp reaches its temperature of the projector projector is ready to be projector is turned on.
end of life.
Blinks yellow when the lamp
cannot light up.
is too high. (pp.46, 55–56)
turned on. And it blinks And it becomes bright
green in the Power when the projector is in
management mode.
(pp.40, 46, 55–56)
stand-by mode.
(pp.20, 21, 55-56)
(pp.48, 55–56)
POWER ON–OFF BUTTON
MENU BUTTON
Used to turn the projector
on or off. (pp.20, 21)
Used to open or
close the On-Screen
Menu. (pp.18, 19)
INPUT BUTTON
Used to select an input
source. (pp.24, 31)
ZOOM BUTTON
Used to adjust zoom.
(p.22)
AUTO PC ADJ. BUTTON
Used to operate the Auto
PC Adjustment function.
(p.26)
FOCUS BUTTON
Used to adjust focus.
(p.22)
IMAGE BUTTON
Used to select the
image level.
(pp.29, 33)
LENS SHIFT BUTTON
SELECT BUTTON
Used to select the Lens
Shift function. (p.22)
Used to execute the
selected item. It is also
used to expand/compress
the image in the DIGITAL
ZOOM mode. (p.30)
POINT (VOLUME + / – ) BUTTONS
Used to select an item or adjust a
value in On-Screen Menu. They are
also used to pan the image in the
DIGITAL ZOOM +/– mode. (p.30)
The POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.
(p.23)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
REMOTE CONTROL
You can control and adjust this projector with On-Screen
Menu. Refer to the relevant pages to operate each
adjustment.
1. DISPLAY MENU
POINT BUTTONS
Press the MENU button to display the On-Screen Menu.
Used to move the
Pointer UP/DOWN/
RIGHT/LEFT.
2. MOVING POINTER
Move the pointer (✽ see below) or adjust a value of an item by
pressing the POINT buttons on the top control or on the remote
control.
✽ The Pointer is an icon in the On-Screen Menu for selecting
an item. See figures in “FLOW OF ON-SCREEN MENU
OPERATION” below.
MENU BUTTON
SELECT BUTTON
Used to select the item.
TOP CONTROL
3. SELECT ITEM
Select an item or set the selected function by pressing the
SELECT button.
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
MENU BUTTON
SELECT BUTTON
Used to select the item.
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
MENU ICON
Display ON-SCREEN MENU
Press the MENU button to display the On-Screen Menu
(a MENU BAR). A red frame is a POINTER.
1
POINTER
(red frame)
Select Menu to be adjusted
POINTER (red frame)
Press the POINT UP/DOWN
buttons to move the POINTER.
Move the POINTER (red frame) to a MENU ICON that
you want to select by pressing the POINT RIGHT/LEFT
buttons.
2
ITEM
Control or adjust items through ON-SCREEN MENU
SELECT
BUTTON
Press the POINT UP/DOWN buttons and move the
3
POINTER (red frame or red arrow) to an ITEM that you
want to adjust, and then press the SELECT button to
show the ITEM DATA.
Adjust the ITEM DATA by pressing the POINT
RIGHT/LEFT buttons.
Refer to the relevant pages for details of respective
adjustments.
4
ITEM DATA
Press the POINT LEFT/RIGHT
buttons to adjust a value or set a
function.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
GUIDE WINDOW
Press the MENU button when connecting to the PC input source.
IMAGE SELECT MENU
SCREEN MENU
SETTING MENU
Used to select an
image level among
Standard, Real, and
Image 1–10.
Used to adjust the
size of an image.
[Normal/True/Wide/ or reset the Lamp
Full/Digital zoom replacement counter.
+/–] (See page 30.) (See pages 38–44.)
Used to change
settings of the projector
PC SYSTEM MENU
Shows the
selected item of
On-Screen Menu.
Used to select a
computer system.
(See pages 24–25.)
(See page 29.)
IMAGE ADJUST MENU
SOUND MENU
INPUT MENU
PC ADJUST MENU
Used to adjust the computer Used to adjust
Used to select an
input source (Input 1, parameters to
Used to adjust the
image. [Contrast/
the volume,
Brightness/Color/Tint/Color
management/Auto picture
control/Color temp./White
switch the Built-
in SP. On/Off, or
mute the sound.
Input 2, or Input 3).
(See page 24.)
match with the input
signal format.
(See pages 26–28.)
balance (R/G/B)/Sharpness/ (See page 23.)
Gamma/Noise reduction/
Progressive]
(See pages 35–37.)
FOR VIDEO SOURCE
Press the MENU button when connecting to the VIDEO input source.
INPUT MENU
IMAGE SELECT MENU
Used to select an
input source
(Input 1, Input 2,
or Input 3).
Used to select an
image level among
Standard, Cinema,
and Image 1–10.
(See page 33.)
SCREEN MENU
Used to adjust the size
of image to Normal or
Wide. (See page 34.)
(See page 31.)
AV SYSTEM MENU
IMAGE ADJUST MENU
Same function as
menu for PC source.
Same function as
menu for PC source.
Used to select the
system of selected
video source.
Used to adjust the picture
image. [Contrast/Brightness/
Color/Tint/Color management/
Auto picture control/Color
temp./White balance (R/G/B)/
Sharpness/Gamma/Noise
reduction/Progressive]
(See page 32.)
(See pages 35–37.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON THE PROJECTOR
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.
1
2
16
Connect the projector’s AC power cord into an AC outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
Press the POWER ON-OFF button on the top control or on
the remote control. The LAMP indicator dims, and the cooling
fans start to operate. The preparation display appears on the
screen and the countdown starts.
3
4
The preparation display disappears after 30 seconds.
Selected Input Source and Lamp control
After the countdown, the input source that was selected the
last time and the Lamp control status icon (see page 41)
appear on the screen.
Lamp control status
If the projector is locked with a PIN code, a PIN code Input
Dialog Box appears. Enter a PIN code as instructed below.
PIN code Input Dialog Box
To Enter a PIN code
Select a number by pressing the POINT LEFT/RIGHT button and
fix the number with the SELECT button. The number changes to
“✳.” If you fixed a wrong number, move the pointer to “Set” or
“Clear” once by pressing the POINT DOWN button, then return to
“PIN code.” Enter the correct number.
Pointer
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer automatically
moves to “Set.” Press the SELECT button so that you can start to
operate the projector.
If you entered a wrong PIN code, “PIN code” and the number
(✳✳✳✳) turn red and disappear. Enter a PIN code all over again.
After the OK icon
disappears, you can
operate the projector.
What is PIN code?
PIN (Personal Identification Number) code is a security code that
allows the person who knows it to operate the projector. Setting a
PIN code prevents unauthorized use of the projector.
A PIN code consists of a four-digit number. Refer to the PIN code
lock function in SETTING Menu on page 43 for locking operation
of the projector with your PIN code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take special care in setting a new
PIN code; write down the number in a column on
page 60 of this manual and keep it at hand. Should
the PIN code be missing or forgotten, consult your
dealer or service center.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING OFF THE PROJECTOR
Press the POWER ON-OFF button on the top control or on
the remote control, and “Power off?” appears on the screen.
1
2
Press the POWER ON-OFF button again to turn off the
projector. The LAMP indicator lights bright and the READY
indicator turns off. After the projector is turned off, the cooling
fans operate (for 90 seconds). During this “cooling down”
period, the projector cannot be turned on.
“Power off?” disappears after 4 seconds.
When the projector has cooled down, the READY indicator
lights GREEN again and you can turn projector on. After
cooling down completely, unplug the AC power cord.
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU
TURN THE PROJECTOR ON, WAIT AT LEAST FIVE
MINUTES BEFORE TURNING IT OFF.
DO NOT UNPLUG THE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE THE
READY INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING THE
LAMP LIFE.
Note:
• The projector cannot be turned on during the cooling period with the READY
indicator turned off. You can turn it on again after the READY indicator becomes
GREEN again.
• When the On start function is “On,” this projector is turned on automatically by
connecting the AC power cord to an AC outlet. (See page 41 for the On start
function.)
• Continuous use may result in shortening the lamp life. Turn off the projector
and rest it for about an hour in every 24 hours.
• The running speed of cooling fans is changed according to the temperature
inside the projector.
• If the WARNING TEMP indicator blinks RED, see “WARNING TEMP
INDICATOR” on page 46.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press the ZOOM button on the top control or ZOOM ▲/▼
buttons on the remote control. “Zoom” appears on the screen.
1
2
Press the ZOOM ▲ button or POINT UP button to make the
image larger, and press the ZOOM ▼ button or POINT DOWN
button to make the image smaller.
“Zoom” disappears after 4 seconds.
FOCUS ADJUSTMENT
Press the FOCUS button on the top control or FOCUS ▲/▼
buttons on the remote control. “Focus” appears on the screen.
1
2
Adjust the focus of image by pressing the FOCUS ▲/▼ buttons
or POINT UP/DOWN buttons.
“Focus” disappears after 4 seconds.
NOTE:
• Focus adjustment may not function properly if the image is corrected by the
Keystone function.
LENS SHIFT ADJUSTMENT
Press the LENS SHIFT button on the top control or LENS SHIFT
▲/▼ buttons on the remote control. “Lens shift” appears on the
screen.
1
2
Press the POINT UP button or LENS SHIFT ▲ button to move
the image up, press the POINT DOWN or LENS SHIFT ▼ button
to move the image down.
“Lens shift” disappears after 4 seconds.
KEYSTONE CORRECTION
If a projected picture has keystone distortion, correct the image with the Keystone function.
Press the KEYSTONE button on the remote control or select
Keystone in the SETTING Menu. (See page 38.) The Keystone
dialog box appears.
1
Correct keystone distortion by pressing the POINT
UP/DOWN/LEFT/RIGHT buttons. Press the POINT UP button to
reduce the upper part of the image; press the POINT DOWN
button to reduce the lower part. Press the POINT LEFT button to
reduce the left part; press the POINT RIGHT button to reduce
the right part.
2
• Arrows are white when no correction.
• Arrow(s) in the corrected direction turn(s) red.
• Arrow(s) disappear(s) at the maximum correction.
• If you press the KEYSTONE button on the remote
control once more while the Keystone dialog box is
being displayed, the Keystone function is canceled.
• “Keystone” disappears after 10 seconds.
Reduce the upper width
with POINT UP button.
Reduce the lower width
with POINT DOWN button.
Reduce the left part with
POINT LEFT button.
Reduce the right part with
POINT RIGHT button.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press the FREEZE button on the remote control to freeze the picture on the screen. To cancel the FREEZE
function, press the FREEZE button again or press any other button.
NO SHOW FUNCTION
Press the NO SHOW button on the remote control to black out
the image. To restore to normal, press the NO SHOW button
again or press any other button.
“No show” disappears after 4 seconds.
P-TIMER FUNCTION
Press the P-TIMER button on the remote control. A Timer
display “00 : 00” appears on the screen and starts to count time
(00 : 00–59 : 59).
To stop the P-TIMER, press the P-TIMER button. Press the P-
TIMER button again to cancel the P-TIMER function.
SOUND ADJUSTMENT
Indicates an approximate level of the volume.
DIRECT OPERATION
Volume
Press the VOLUME (+/–) buttons on the top control or on the remote
control to adjust the volume. A Volume dialog box appears on the
screen for a few seconds.
Press the VOLUME (+) button to increase the volume; press the
VOLUME (–) button to decrease the volume.
Mute
Press the MUTE button to set
the Mute function On or Off.
Press the MUTE button on the remote control to turn off the sound. To
restore the sound to its previous level, press the MUTE button again
or press the Volume (+/–) buttons.
The Volume dialog box disappears after 4 seconds.
MENU OPERATION
Press the MENU button to display the On-Screen Menu. Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to the SOUND Menu icon.
1
SOUND MENU
Press the POINT UP/DOWN buttons to move the red frame
pointer to the desired item, and then press the SELECT button.
2
SOUND Menu icon
Indicates an approximate
level of the volume.
Volume
To increase the volume, press the POINT RIGHT button; to decrease
the volume, press the POINT LEFT button.
Closes the SOUND Menu
Built-in SP.
Press the POINT LEFT/RIGHT buttons to switch the built-in speaker
On or Off.
Mute
Press the POINT LEFT/RIGHT buttons to turn off the sound. The
Dialog box display is changed to “On” and the sound is turned off. To
restore the sound to its previous level, press the POINT LEFT/RIGHT
buttons again.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
INPUT button
Input 1
Select an INPUT source by pressing the INPUT button on
the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons
on the remote control.
✽
If the projector cannot reproduce proper image, select a
correct input source with the MENU OPERATION (see
below).
Input 2
Input 3
NOTE:
• Input 1 terminal is switchable and can be used as Computer Input or Monitor
Output.
✽Input 1 is not displayed when the Input 1 is used as
Monitor out.
MENU OPERATION
WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS )
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the INPUT Menu icon.
1
2
3
INPUT MENU
Press the POINT UP/DOWN buttons to move the red arrow
pointer to Input 1 and then press the SELECT button. A
Source Select Menu appears.
INPUT Menu icon
Move the pointer (red arrow) to Input 1
and press the SELECT button.
Move the pointer to a source that you want to select and then
press the SELECT button.
RGB (PC analog)
Input 1
When your computer is connected to the INPUT 1 (ANALOG)
terminal, select RGB (PC analog).
Source Select Menu
Move the pointer (red arrow)
to a source and press the
SELECT button.
RGB (Scart)
When scart video equipment is connected to the INPUT 1
(ANALOG) terminal, select RGB (Scart).
RGB (PC digital)
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB (PC digital).
RGB (AV HDCP)
If a HDCP-compatible signal source is connected to the
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).
Monitor out
If the INPUT 1 ANALOG terminal is being used as a
MONITOR OUT terminal, select Monitor out.
NOTE:
• INPUT SOURCE changes if the INPUT 1 button on the remote control is
pressed.
• HDCP (High-bandwidth Digital Content Protection) is a system for protecting
digital entertainment content which is delivered by DVI (Digital Visual Interface)
from being copied. The specification of HDCP is decided and controlled by
Digital Content Protection, LLC. Should the specification be changed, this
projector may not display the digital content protected by HDCP.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
When connecting a computer output [5 BNC Type (Green,
Blue, Red, Horiz. Sync, and Vert. Sync.)] from a computer to
G, B, R, H/HV, and V jacks:
INPUT MENU
INPUT Menu icon
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the INPUT Menu icon.
1
Move the pointer (red arrow) to Input 2
and press the SELECT button.
Press the POINT UP/DOWN buttons to move the red arrow
pointer to Input 2 and then press SELECT button. A Source
Select Menu appears.
2
Input 2
Press the POINT UP/DOWN buttons and a red-arrow icon
appears. Move the arrow to “RGB,” and then press the
SELECT button.
3
Source Select Menu
Move the pointer (red arrow)
to RGB and press the
SELECT button.
NOTE:
• INPUT SOURCE changes if the INPUT 2 button on the remote control is
pressed.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+,
WXGA, or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on pages 54–55). When Computer
is selected, this projector automatically detects the incoming signal and projects proper image without any
additional setting. (Some computers need to be set manually.)
The projector displays one of these: Auto, -----, Mode 1–10, or the system provided in the projector.
When the projector cannot recognize a connected signal
as PC system provided in this projector, the Auto PC
Auto
PC SYSTEM MENU
Adjustment function operates to adjust the projector and
“Auto” is displayed on the SYSTEM Menu icon.
When the image is not provided properly, a manual
adjustment is required. (See pages 27–28.)
PC SYSTEM Menu icon
Displays system being selected.
There is no signal input from the computer. Make sure
the connection of a computer and the projector is set
correctly. (See “TROUBLESHOOTING” on page 50.)
-----
The User preset adjustment in MANUAL PC
ADJUSTMENT. The Adjusted data can be stored in
the Mode 1–10.
Mode 1
SVGA 1
PC systems provided in this projector. The projector
chooses proper system and displays it.
✽ Mode 1 and SVGA 1 are examples.
PC SYSTEM MENU
SELECTING COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those
provided in this projector, however, PC system can be also
selected manually.
PC SYSTEM Menu icon
Displays system being selected.
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the PC SYSTEM Menu icon.
Systems in this dialog box can be
selected.
1
Custom Mode (1–10) set in PC
ADJUST Menu. (pp.27–28)
Press the POINT UP/DOWN buttons to move the red arrow
pointer to the desired system, and then press SELECT button.
2
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical
positions to conform to your computer. Auto PC Adjustment function can be operated as follows.
Auto PC adj.
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the PC ADJUST Menu icon.
1
PC ADJUST MENU
Press the POINT UP/DOWN buttons to move the red frame
pointer to the AUTO PC adj. icon and then press the SELECT
button.
PC ADJUST Menu icon
2
This Auto PC Adjustment can be also executed by pressing
the AUTO PC ADJ. button on the top control or on the remote
control.
Move the red frame pointer to the Auto PC
adj. icon and press the SELECT button.
To store the adjusted parameters.
The system parameters from Auto PC Adjustment can be memorized in this
projector. Once the parameters are stored, the setting can be done just by
selecting Mode in PC SYSTEM Menu (p.25). See MANUAL PC
ADJUSTMENT on pages 27–28.
NOTE:
• Fine sync, Total dots, and Picture Positions of some computers can not be fully
adjusted with the Auto PC Adjustment function. When the image is not provided
properly with this function, manual adjustments are required. (See pages
27–28.)
• Auto PC Adjustment function cannot be operated in Digital Signal Input on the
DVI terminal and “480p,” “575p,” “480i,” “575i,” “720p (HDTV),” “1035i
(HDTV),” or “1080i (HDTV)” is selected on the PC SYSTEM Menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed.
However, some computers employ special signal formats which may not be tuned by the Multi-Scan system of
this projector. If this happens, the projector cannot reproduce proper image and it may be recognized as a
flickering; non-synchronized; non-centered; or skewed picture.
Manual PC Adjustment of this projector enables you to precisely adjust several parameters to match with those
special signal formats. This projector has 10 independent memory areas to store those parameters manually
adjusted, which allows you to recall setting for a specific computer whenever you use it.
Note: The PC ADJUST Menu cannot be operated when the digital signal input on the DVI terminal is selected
on PC SYSTEM Menu. (p.25)
PC ADJUST MENU
Press the MENU button to display the On-Screen Menu.
1
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the PC ADJUST Menu icon.
PC ADJUST Menu icon
Press the POINT UP/DOWN buttons to move the red frame
2
pointer to the desired item, and then press the SELECT
Move the red frame pointer to an item
button. An Adjustment dialog box appears. Press the POINT
and press the SELECT button.
LEFT/RIGHT buttons to adjust the value.
Fine sync
Eliminate a flicker from the display. Press the POINT LEFT/RIGHT
buttons to adjust the value (from 0 to 31).
Shows status (Stored/Free)
of the selected Mode.
Total dots
Adjust the number of total dots in one horizontal period. Press the
POINT LEFT/RIGHT buttons to adjust the number to match your
PC image.
Selected Mode
Position H
Press the POINT LEFT/RIGHT
Press the POINT LEFT/RIGHT buttons to adjust the horizontal
buttons to adjust the value.
picture position.
Press the SELECT button at this icon
to adjust “Clamp,” “Display area H,” or
Position V
“Display area V.”
Press the POINT LEFT/RIGHT buttons to adjust the vertical picture
position.
Current mode
Press the SELECT button to show H-sync freq. and V-sync freq. of
the connected computer.
Current mode
Clamp
Adjusts the clamp level. When the image has a dark bars, try this
adjustment.
Press the SELECT
button at the Current
mode icon to show
information of the
Display area H
Adjusts the horizontal area displayed by this projector. Press the
POINT LEFT/RIGHT buttons to decrease/increase the value.
computer connected.
Press the SELECT button at this icon
to display the previous items.
Display area V
Adjusts the vertical area displayed by this projector. Press the
POINT LEFT/RIGHT buttons to decrease/increase the value.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
Reset
To store adjustment data.
To reset the adjusted parameters, select Reset and press the
SELECT button. A confirmation box appears. Select [Yes]. All
the adjustments return to their previous figures.
This Mode has parameters being stored.
Mode free
To clear adjusted parameters previously set, move the red frame
pointer to the Mode free icon and then press the SELECT
button. Move the red arrow pointer to a Mode that you want to
clear and then press the SELECT button.
Store
To store the adjusted parameters, move the red frame pointer to
the Store icon and then press the SELECT button. Move the red
arrow pointer to any of the Mode 1 to 10 in which you want to
store the parameters and then press the SELECT button.
Close this dialog box.
Vacant
Shows the values of “Total
dots,” “Position H,” “Position V,”
“Display area H,” and “Display
area V.”
Quit
Exit the PC ADJUST Menu.
A confirmation box appears
and then select [Yes].
To clear adjustment data.
Close this dialog box.
A confirmation box appears
and then select [Yes].
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT
DIRECT OPERATION
IMAGE button
Select an image level from among Standard, Real, and
Image 1 to Image 10 by pressing the IMAGE button on the
top control or on the remote control.
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Real
Picture level with improved halftone for graphics.
Image 10
IMAGE 1–10
User preset picture adjustment in the IMAGE ADJUST Menu.
(pp.35–37)
MENU OPERATION
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
Press the POINT UP/DOWN buttons to move the red frame
pointer to the desired level and then press the SELECT
button.
2
IMAGE SELECT Menu icon
Standard
Move the red frame pointer to a level and
press the SELECT button.
Normal picture level preset on this projector.
Real
Picture level with improved halftone for graphics.
IMAGE 1–10
User preset picture adjustment in the IMAGE ADJUST Menu.
(pp.35–37)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
PICTURE SCREEN SELECT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the SCREEN Menu icon.
SCREEN MENU
1
Press the POINT UP/DOWN buttons and move the red frame
pointer to the desired function and then press the SELECT
button.
2
SCREEN Menu icon
Move the red frame pointer to a function and
press the SELECT button.
Normal
Provides the image to fit the screen size.
NOTE:
True
• True, Full, and Digital zoom +/– cannot be operated when
“480i,” “575i,” “480p,” or “575p” is selected on the PC
SYSTEM Menu. (p.25)
Provides image in its original size.
• The Screen Menu cannot be operated when “720p
(HDTV),” “1035i (HDTV),” or “1080i (HDTV)” is selected
on the PC SYSTEM Menu. (p.25)
• This projector cannot display any resolution higher than
1600 x 1200. If your computer’s screen resolution is
higher than 1600 x 1200, lower the resolution before
connecting the projector.
Wide
Provides the image to fit the wide video aspect ratio (16:9) by
expanding the image width uniformly. This function can be used to
provide the squeezed video signal at 16:9.
Full
• The image data other than XGA (1024 x 768) is modified to
fit the screen size in initial mode.
• The Panning function may not operate properly if the
computer system prepared on the PC ADJUST Menu is
used.
Provides the full screen image.
Digital zoom +
When the Digital zoom + is selected, the On-Screen Menu
disappears and “D. Zoom +” appears. Press the SELECT button to
expand the image size. Press the POINT UP/DOWN/LEFT/RIGHT
buttons to pan the image. The Panning function can work only
when the image is larger than the screen size.
The projected image can be also expanded by pressing the
D.ZOOM ▲ button on the remote control.
Digital zoom –
When the Digital zoom – is selected, the On-Screen Menu
disappears and “D. Zoom –” appears. Press the SELECT button to
compress the image size.
The projected image can be also compressed by pressing the
D.ZOOM ▼ button on the remote control.
To cancel the Digital Zoom +/– mode, press any button except
D.ZOOM ▲/▼, SELECT, POINT, and LASER buttons.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
INPUT button
Select an INPUT source by pressing the INPUT button on
the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons
on the remote control.
If the projector cannot reproduce proper image, select a
correct input source with the MENU OPERATION (see
below).
Input 1
Input 2
Input 3
✽Input 1 is not displayed when the Input 1 is used as
Monitor out.
MENU OPERATION
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
When connecting to video equipment, select a type of Video
source in the Source Select Menu.
INPUT MENU
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the INPUT Menu icon.
1
INPUT Menu icon
Move the pointer (red arrow) to Input 2
and press the SELECT button.
Press the POINT UP/DOWN buttons to move the red arrow
pointer to Input 2 and then press the SELECT button. A
Source Select Menu appears.
2
Input 2
Move the pointer to a source that you want to select and then
3
press the SELECT button.
Source Select Menu
When the video input signal is connected to the
VIDEO jack, select Video.
Video
Move the pointer (red arrow)
to Video or Y, Pb/Cb, Pr/Cr
and press the SELECT
button.
When the video input signal is connected to the Y-
Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y, Pb/Cb, Pr/Cr
NOTE:
• INPUT SOURCE changes if the INPUT 2 button on the remote control is
pressed.
WHEN SELECTING INPUT 3 (AV TERMINALS )
When connecting to video equipment, select a type of Video
source in the Source Select (Video) Menu.
INPUT MENU
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the INPUT Menu icon.
1
INPUT Menu icon
Press the POINT UP/DOWN buttons to move the red arrow
pointer to Input 3 and then press the SELECT button. A
Source Select Menu appears.
2
Move the pointer (red arrow) to Input 3
and press the SELECT button.
Input 3
Move the pointer to a source that you want to select and then
3
press the SELECT button.
Source Select Menu
Move the pointer (red arrow)
to a source and press the
SELECT button.
When the video input signal is connected to the
Video
VIDEO jack, select Video.
When the video input signal is connected to the Y-
Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y, Pb/Cb, Pr/Cr
When the video input signal is connected to the S-
VIDEO jack, select S-Video.
S-Video
NOTE:
• INPUT SOURCE changes if the INPUT 3 button on the remote control is
pressed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING VIDEO SYSTEM
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the AV SYSTEM Menu icon.
1
2
Press the POINT UP/DOWN buttons to move the red arrow
pointer to the desired system and then press the SELECT
button.
VIDEO JACK OR S-VIDEO JACK
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
The projector automatically detects an incoming video system, and
adjusts itself to optimize its performance.
AV SYSTEM Menu icon
This box indicates system being
selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce proper video image, select a
specific broadcast signal format from among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move the pointer (red arrow) to
system and press the SELECT button.
Y, Pb/Cb, Pr/Cr JACKS
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
The projector automatically detects an incoming video signal, and
adjusts itself to optimize its performance.
When the Video System is 1035i or 1080i, select the system
manually.
AV SYSTEM Menu icon
This box indicates system being
selected.
COMPONENT VIDEO SIGNAL FORMAT
Move the pointer (red arrow) to
system and press the SELECT button.
If the projector cannot reproduce proper video image, select a
specific component video signal format from among 480i, 575i,
480p, 575p, 720p, 1035i, and 1080i.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT
DIRECT OPERATION
IMAGE button
Standard
Select an image level from among Standard, Cinema, Image
1 to Image 10 by pressing the IMAGE button on the top
control or on the remote control.
Cinema
Image 1
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
Image 10
IMAGE 1–10
User preset picture adjustment in the IMAGE ADJUST Menu.
(pp.35–37)
MENU OPERATION
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the IMAGE SELECT Menu icon.
1
IMAGE SELECT MENU
Press the POINT UP/DOWN buttons to move the red frame
pointer to the desired level and then press the SELECT
button.
IMAGE SELECT Menu icon
2
Move the red frame pointer to a level and
press the SELECT button.
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1–10
User preset picture adjustment in the IMAGE ADJUST Menu.
(pp.35–37)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE SCREEN ADJUSTMENT
PICTURE SCREEN SELECT
This projector has a picture screen resize function, which enables you to customize the image size.
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the SCREEN Menu icon.
1
SCREEN MENU
Press the POINT DOWN button and move the red frame
pointer to the desired function and then press the SELECT
button.
SCREEN Menu icon
2
Move the red frame pointer to a function and
press the SELECT button.
Normal
Provides image at the normal video aspect ratio of 4:3.
NOTE:
• SCREEN Menu can not be operated when “720p,”
“1035i,” or “1080i” is selected on AV SYSTEM Menu
(p.32).
Wide
Provides image at the wide screen ratio of 16:9.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
PICTURE IMAGE ADJUSTMENTS
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the IMAGE ADJUST Menu icon.
1
2
IMAGE ADJUST MENU
Press the POINT UP/DOWN buttons to move the red frame
pointer to the desired item and then press the SELECT
button. The level of each item is displayed. Adjust each level
by pressing POINT LEFT/RIGHT buttons.
IMAGE ADJUST Menu icon
Move the red frame pointer to item to be
selected and then press SELECT button.
Contrast
Press the POINT LEFT button to decrease contrast; press the
POINT RIGHT button to increase the contrast (from 0 to 63).
Brightness
Press the POINT LEFT button to decrease the brightness; press
the POINT RIGHT button to increase the brightness (from 0 to 63).
Color
Press the POINT LEFT button decrease the intensity of the color;
press the POINT RIGHT button to increase the intensity of the color
(from 0 to 63).
Tint
Press the POINT LEFT/RIGHT buttons to adjust the tint value to
obtain proper color balance (from 0 to 63).
Color Management
Press the POINT LEFT/RIGHT buttons to
adjust the value.
The Color management function can be used to adjust the LEVEL,
PHASE, and GAMMA of the selected display colors (except for
black, white, and gray) on the screen and replace these colors with
other colors if required.
You can store up to eight (8) color management data.
Press the POINT UP/DOWN buttons to move the red frame
pointer to Color management, and then press the SELECT
button. The image being projected freezes, and the COLOR
MANAGEMENT POINTER appears.
1
POINTER MODE
Use the POINT UP/DOWN/LEFT/RIGHT buttons to move the
pointer to a spot where you want to adjust the color and then
press the SELECT button. The COLOR SELECTION window
appears, and the color in the center of the pointer is selected
and you can adjust the color.
2
COLOR MANAGEMENT
POINTER
NOTE:
Use the POINT UP/DOWN/LEFT/RIGHT buttons to adjust the
Press the COLOR M. button on the remote control
to display the COLOR MANAGEMENT POINTER.
If you would like to check or readjust the color
management setting that has already been made,
press the COLOR M. button on the remote control
once more to display the COLOR MANAGEMENT
LIST.
3
LEVEL and PHASE of the color, and then press the SELECT
button to confirm the setting. Then use the POINT UP/DOWN
buttons to adjust the GAMMA for the color and press the
SELECT button to accept the setting. After adjusting, press
the SELECT button to go to the COLOR MANAGEMENT
LIST.
COLOR SELECTION MODE
LIST
Go to the COLOR MANAGEMENT LIST.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
COLOR SELECTION MODE (continued)
COLOR SELECTION MODE
COLOR M.
Level and phase
Gamma
adjustment palette.
adjustment palette.
Return to the COLOR MANAGEMENT POINTER. (If you
press the MENU button on the top control or the remote
control, it returns to the COLOR MANAGEMENT POINTER
and you will need to reselect and readjust the color.)
MENU
Return to the IMAGE ADJUST Menu. But any settings that
have been changed will not be stored. To store the changed
settings, be sure to select “LIST” and go to the COLOR
MANAGEMENT LIST.
In the COLOR MANAGEMENT LIST, the adjusted color data
are check marked. You can decide whether or not to apply
the adjusted color data in the list to the projected image (see
below).
4
LIST
COLOR M.
MENU
LIST MODE
LIST MODE
Clear the check mark if you do not want to apply the adjusted
color data; select the check mark and then press the SELECT
button. The check make disappears.
COLOR PALETTE
DEL
COLOR PALETTE
Return to the COLOR SELECTION mode so that you can
readjust the setting for the color in that line. (This option is not
available if the check mark is cleared.)
DEL
Select the DEL box if you want to delete the adjusted data.
Press the SELECT button and a confirmation box appears
and then select [Yes]
ALL DEL
Delete all the data in the list. Press the SELECT button and a
confirmation box appears and then select [Yes].
MENU
ALL DEL
NOTE:
MENU
COLOR M.
The same function as stated above.
COLOR M.
If you press the COLOR M. button on the remote
control, the display returns to the normal projection
screen, but any settings that have been changed
will not be stored. To store the changed settings,
be sure to select “MENU” to return to the IMAGE
ADJUST Menu and store the settings.
The same function as stated above.
Auto picture control
Press the POINT LEFT/RIGHT buttons to select the desired Auto
picture control position (Off, L1 or L2).
Off . . . . Auto picture control OFF position.
L1 . . . . . Auto picture control LEVEL 1 position.
L2 . . . . . Auto picture control LEVEL 2 position.
Color temp.
Press either the POINT LEFT/RIGHT buttons to select the desired
Color temp. level (XLow, Low, Mid or High).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
White balance (Red)
Press the POINT LEFT button to lighten red tone; press the POINT
RIGHT button to deepen red tone (from 0 to 63).
White balance (Green)
Press the POINT LEFT button to lighten green tone; press the
POINT RIGHT button to deepen green tone (from 0 to 63).
White balance (Blue)
Press the POINT LEFT button to lighten blue tone; press the
POINT RIGHT button to deepen blue tone (from 0 to 63).
Press the SELECT button at this icon to
display other items.
Sharpness
Press the POINT LEFT button to decrease the sharpness of the
image; press the POINT RIGHT button to increase the sharpness of
the image (from 0 to 31).
Press the SELECT button at this
icon to display the previous items.
Gamma
Press the POINT LEFT/RIGHT buttons to adjust the gamma value
to obtain better balance of contrast (from 0 to 15).
Press the POINT LEFT/RIGHT
buttons to adjust the value.
Noise reduction
Noise interference on the screen can be reduced. Press the POINT
LEFT/RIGHT buttons to change the noise reduction mode.
Off . . . . Noise reduction mode is “Off”
L1 . . . . . For lower reduction
L2 . . . . . For higher reduction
Progressive
An interlaced video signal can be displayed in progressive. Press
the POINT LEFT/RIGHT buttons to change the progressive scan
mode.
Off . . . . Progressive scan mode is “Off.”
On . . . . Progressive scan mode is “On.”
Film . . . Select for watching a film. With this function, the
projector reproduces pictures faithful to the original film
quality.
NOTE:
• The Film mode in the Progressive function cannot be selected when the video
signal format is 1080i or 1035i.
Reset
To reset the adjusted parameters, select Reset and press the
SELECT button. A confirmation box appears. Select [Yes]. All the
adjustments return to their previous figures.
Image Level Menu
Move the red frame pointer to any of
Image 1 to 10 where you want to set
and then press the SELECT button.
Store
To store the manually preset image, move the red frame pointer to
the Store icon and press the SELECT button. The Image Level
Menu appears. Move the red arrow pointer to any of the Image 1 to
10 in which you want to set and press the SELECT button.
Store icon
Press the SELECT button at this
icon to store the adjustment.
Quit
Exit the IMAGE ADJUST Menu.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
This projector has Setting menu that allows you to set up the other various functions described as follows:
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move the red frame
pointer to the Setting Menu icon.
1
SETTING MENU (LANGUAGE)
Press the POINT DOWN button to move the red frame pointer
2
SETTING Menu icon
to the desired item that and then press the
SELECT button.
The Setting dialog box appears.
Set the red frame pointer
to the item and press the
SELECT button.
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
Keystone
This function corrects distortion of a projected image. Select either
Store or Reset with the POINT LEFT/RIGHT buttons, and then
press the Select button. The Keystone dialog box appears. Correct
keystone with the POINT UP/DOWN/LEFT/RIGHT buttons. (p.22)
Store . . . stores the keystone correction even if the AC power
cord is unplugged.
When pressing the SELECT
button at Language, the
Language Menu appears.
Reset . . resets the keystone correction when the AC power cord
is unplugged.
Background
Three background settings are available in this projector. Select
one of the following options when no input source is connected to
the projector or no input signal is coming from the connected
equipment.
Blue . . . blue colored background
User . . . the image you captured
Black . . black colored background
Display
This function decides whether to display On-Screen Displays.
On . . . . . . . . . . . . shows all the On-Screen Display.
Count-down Off . . hide the Count-down Display.
Off . . . . . . . . . . . . hide the On-Screen Display except:
● On-Screen Menu
● “Power off?” (p.21)
● P-TIMER (p.23)
● ”Please wait....”
● Color management operation screen
(pp.35–36)
● “No signal” for Power management (p.40)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Logo
Logo
This function allows you to customize the screen logo with Logo
select, Capture, and Logo PIN code lock functions.
Logo select
This function decides the start-up display as follows:
User . . . the image you captured
Default . the factory-set logo
Off . . . . count-down only
Capture
This function enables you to capture the image being projected
and use it for a starting-up display.
After capturing the projected image, go to the Logo select function
and set it to “User.” Then the captured image will be displayed
when turning on the projector the next time.
Select [Yes] to
capture the
projected image.
To capture the image, select [Yes]. To cancel the Capture
function, select [No].
NOTE:
Select [Yes] to stop
capturing.
• Before capturing an image, select Standard in the IMAGE SELECT Menu to
capture proper image. (See pages 29, 33.)
• A signal from a computer can be captured up to XGA (1024 X 768).
• Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the Keystone function,
the adjusted data is automatically reset and the projector captures an image
without keystone correction.
• When starting to capture a new image, the previously stored image is cleared
even if you cancel the capturing.
• Once you exit the Logo Menu after setting the Logo lock to "On," you are
required to enter the PIN code every attempting to change the Logo setting.
Logo PIN Code Lock Dialog Box
Logo PIN code lock
Pointer
This function prevents an unauthorized person from changing the
Logo setting.
Off . . . . the Logo setting can be changed freely from the Logo
function.
Quit
On . . . . the Logo setting cannot be changed without a Logo
PIN code.
After a correct Logo PIN code is entered, the following dialog box
appears.
If you want to change the Logo PIN code lock setting, enter a
Logo PIN code by following the steps below. The initial Logo PIN
code is set to “4321” at the factory.
To Enter a Logo PIN code
Select On/Off by pressing the POINT LEFT/RIGHT buttons or
change the Logo PIN code.
Select a number by pressing the POINT LEFT/RIGHT buttons and
fix the number with the SELECT button. The number changes to
“✳.” If you fixed a wrong number, move the pointer to “Set” or
“Clear” once by pressing the POINT DOWN button, then return to
“Logo PIN code.” Enter the correct number.
To Change the Logo PIN code
Logo PIN code can be changed to your desired
four-digit number. Select “Logo PIN code change”
with the POINT DOWN button and press the
SELECT button. Set a new Logo PIN code.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer automatically
moves to “Set.” Press the SELECT button so that you can change
the Logo PIN code lock setting.
Be sure to write down the new Logo PIN code and
keep it at hand. If you lost the number, you could
no longer change the Logo PIN code setting. For
details on the PIN code setting, refer to the
relevant instructions of the PIN code lock function
on page 43.
If you entered a wrong Logo PIN code, “Logo PIN code” and the
number (✳✳✳✳) turn red and disappear. Enter a Logo PIN code
all over again.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Ceiling
Ceiling
When this function is “On,” the picture is top/bottom and left/right
reversed. This function is used to project the image from a ceiling-
mounted projector.
Rear
Rear
When this function is “On,” the picture is left/right reversed. This
function is used to project the image to a rear projection screen.
Anamorphic
When this function is “On,” the screen image is forcibly changed to
the 4:3 image, even if the input signal is HDTV.
Simple menu
When this function is “On,” the value adjustment bar in the picture
IMAGE ADJUSTMENT Menu is displayed on the bottom left of the
screen.
Menu position
This function is used to adjust the On-Screen Menu display
position. When the SELECT button is pressed, the adjustment
screen is displayed (arrows appear). Use the POINT UP/DOWN/
LEFT/RIGHT button(s) to adjust the position. After making the
adjustment, press the SELECT button to return to the Menu screen.
Power management
Power management
For reducing power consumption as well as maintaining the lamp
life, the Power management function turns off the projection lamp
when the projector is not used for a certain period.
If the input signal is interrupted and no button is pressed for more
than 30 seconds, the timer display with “No signal” appears on the
screen to start the countdown. The countdown time can be set
between 1 and 30 minutes.
Time left until lamp off
Select one of the following operations:
Ready . . . . . When the lamp has been fully cooled down, the
READY indicator starts blinking. In this condition,
the projection lamp is turned on if the input signal is
reconnected or any button on the top control or
remote control is pressed.
Shutdown . . When the lamp has been fully cooled down, the
power is turned off.
Off . . . . . . . The Power Management function is off.
Press the SELECT button at Power
management and this box appears.
Choose one of three settings with
the POINT LEFT/RIGHT buttons,
and go to the timer with the POINT
DOWN button and set time with the
POINT LEFT/RIGHT buttons.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
On start
When this function is “On,” the projector is automatically turned on
just by connecting the AC power cord to an AC outlet.
NOTE:
• Be sure to turn the projector off properly (see “TURNING OFF THE PROJECTOR”
on page 21). If the projector is turned off in the incorrect sequence, such as
unplugging the AC power cord before completing the cool-down etc., the On
start function does not operate properly.
Lamp control
This function allows you to change the brightness of the screen.
. . . . brightness according to the input signal.
. . . . normal brightness.
. . . . lower brightness reduces the lamp power consumption
and extends the lamp life.
Remote control
Remote control
The eight different remote control codes (Code 1–8) are assigned
to this projector: the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8). This switching function prevents
interference from other remote controls when several projectors or
video equipment next to each other are operated at the same time.
For example, when operating the projector in “Code 7”, the code for
both the projector and the remote control must be switched to
“Code 7.”
To change the code of the projector:
Select from Code 1 to Code 8 in the SETTING Menu.
To change the code of the remote control:
Set the DIP switches 1–3 inside the battery compartment of the
remote control. (See page 15.)
When pressing the SELECT button at
Remote control, the Remote control
code menu appears.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
USB
This Projector has a USB port for interactive operation between the
projector and computers. Set the mode by following the steps
below.
Wireless Mouse mode
Select “
” when controlling a computer with the remote control of
this projector.
Projector mode:
“
” Not used.
Security
Security
Key lock
This function locks operation of the top control and remote
control. It helps to prevent operation by an unauthorized
person.
. . . . unlocked.
. . . . locks operation of the top control.
To unlock, use the remote control.
. . . . locks operation of the remote control.
To unlock, use the top control.
Key lock
If the top control accidentally becomes locked and you do not
have the remote control nearby, unplug the AC power cord
from the AC outlet, and then hold down the SELECT button
and reinsert the AC power cord. This will cancel the top
control lock.
Select Key lock and
this box appears.
Choose one of the
alternatives with the
POINT UP/DOWN
buttons and select
[Yes] to activate it.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
PIN code lock
PIN code lock
This function prevents the projector from being operated by an
unauthorized person and provides the following settings for
security options.
Off . . . . the projector is not locked with the PIN code.
On1 . . . requires to enter the PIN code every time turning on
the projector.
On2 . . . requires to enter the PIN code to operate the projector
once the power cord is disconnected; as long as the
AC power cord is connected, the projector can be
operated without a PIN code.
When the projector is
locked with the PIN
code, the PIN code
lock mark appears on
the menu bar.
Whenever you change the PIN Code Lock setting or the PIN code
(the four-digit number), you are required to enter the PIN code.
“1234” is set as the initial PIN code at the factory.
To Enter a Logo PIN code
Select a number by pressing the POINT LEFT/RIGHT buttons and
fix the number with the SELECT button. The number changes to
“✳.” If you fixed a wrong number, move the pointer to “Set” or
“Clear” once by pressing the POINT DOWN button, then return to
“PIN code.” Enter the correct number.
Entering a PIN code
Pointer
Quit
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer automatically
moves to “Set.” Press the SELECT button so that you can change
the PIN code lock settings.
The input numbers
change to “✳” for security.
If you entered a wrong PIN code, “PIN code” and the number
(✳✳✳✳) turn red and disappear. Enter a Logo PIN code all over
again.
When the pointer
automatically moves to
“Set,” press the SELECT
button.
To Change the PIN Code Lock setting
Select “Off,” “On1,” or “On2” with the POINT LEFT/RIGHT buttons
and then go to “Quit” with the POINT DOWN button. Press the
SELECT button to close the dialog box.
To Change the PIN Code
Changing the PIN code lock setting
The PIN code can be changed to your desired four-digit number.
Select “PIN code change” with the POINT DOWN button, and
press the SELECT button. A New PIN code input dialog box
appears.
Select a desired setting
with the POINT
LEFT/RIGHT buttons.
Select a number with the POINT LEFT/RIGHT buttons and fix the
number with the SELECT button. Repeat it to complete entering a
four-digit number. When the four-digit number is fixed, the pointer
automatically moves to “Set.” Then press the SELECT button.
Change the PIN code
Select PIN code
change and press the
SELECT button. The
New PIN code input
dialog box appears.
CAUTION:
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN
A NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO
ON PAGE 60, AND KEEP IT SECURELY. SHOULD THE PIN
CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO
LONGER BE OPERATED.
The input numbers
are being displayed
for confirmation.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Factory default
Lamp counter
This function is used to reset the Lamp replacement counter. When
replacing the projection lamp, reset the Lamp replacement counter
with this function. See page 49 for operation.
Select Factory default and this box
appears. Select [Yes], and the next
box appears.
Factory default
This function returns all setting values except for the User logo,
Key lock, PIN code lock, Logo PIN code lock, and the Lamp counter
to the factory default settings.
Quit
Exit the SETTING Menu.
Select [Yes] to
activate it.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
WIRELESS MOUSE
Remote control is not only able to operate this projector but also functions as a wireless mouse for most
personal computers. The MOUSE POINTER, DRAG ON/OFF button, and two CLICK buttons are used for
wireless mouse operation.
The Wireless mouse function is available only when the PC mouse pointer is displayed on the screen.
INSTALLATION
To use the remote control as a wireless mouse for a computer, installation of a mouse driver (not supplied) is
required. Make sure that the mouse driver is properly installed on your computer and that the mouse port (or
USB port) of the computer is activated.
Connect the mouse port (or USB port) of your computer to the
CONTROL PORT (or USB connector) of this projector with
Note:When your computer has no mouse port,
1
connect the Serial port of your computer to
the Control cable (or USB cable). (See pages 12–13 for
the Control port of the projector with the
connection.)
Control cable for Serial port (supplied).
Turn on the projector first, and then turn your computer on. If
the computer is switched on first, the Wireless mouse function
may not work properly.
2
OPERATING WIRELESS MOUSE
When controlling the PC mouse pointer, use the MOUSE POINTER, DRAG ON/OFF button, LEFT CLICK
button, and RIGHT CLICK button on the remote control.
MOUSE POINTER
Used to move the PC mouse pointer. The pointer moves to the
direction you are pressing.
DRAG ON
INDICATOR
LEFT CLICK button
This button has the same function as the left button in a PC mouse.
To drag a selected screen object, hold down this button and press
the MOUSE POINTER.
RIGHT CLICK button
This button has the same function as the right button in a PC
mouse.
DRAG ON/OFF
button
DRAG ON/OFF button
MOUSE POINTER
(Moves the pointer)
Use this button and the MOUSE POINTER to drag a selected
screen object. Press and release the DRAG ON/OFF button, then
the DRAG ON INDICATOR lights green and the remote control is in
Drag mode. Use the MOUSE POINTER to drag an screen object.
Press and release the DRAG ON/OFF button again or press any
other button to drop the object.
LEFT CLICK button
(left button of the mouse)
RIGHT CLICK button
(right button of the mouse)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
The Warning Temp. indicator blinks red to let you know the internal
temperature of the projector exceeds a normal level. If the temperature
goes up further, the projector will be turned off automatically and the
Ready indicator goes out. (The Warning Temp. indicator continues
blinking.) After the cooling-off period, the Ready indicator lights on again
and the projector can be turned on by pressing the POWER ON-OFF
button on the top control or the remote control. When you turn on the
projector, the Warning Temp. indicator goes out.
TOP CONTROL
Warning Temp.
Indicator
Ready
Indicator
If the Warning Temp. indicator is still blinking, check the following matters:
– The ventilation slots of the projector may be blocked. In such a case,
reposition the projector so that the ventilation slots are not obstructed.
–The air filters may be clogged with dust particles. Clean them by
following the section “AIR FILTER CARE AND CLEANING” on the next
page.
– If the WARNING TEMP. indicator remains on after performing above
checks, the cooling fans or internal circuits may be malfunctioning.
Contact the service station.
When both of the Warning Temp. and Ready indicators are blinking:
When the projector detects an internal problem, it shuts down automatically and both the Warning Temp. and
Ready indicators start blinking. In this condition, the projector cannot be turned on even if you press the POWER
ON-OFF button on the top control or remote control. If this happens, unplug and reconnect the AC power cord,
and then turn on the projector again to check the operation. If the projector shuts down again or cannot to be
turned on, internal checking and repair is required. Unplug the AC power cord and contact the service station.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
AIR FILTERS CARE AND CLEANING
Air filters help prevent dust from accumulating on the optical elements inside the projector. To whatever extent
the air filters become clogged with dust particles, the cooling fans’ effectiveness is reduced, which may result in
an internal heat build-up and adversely affect the life of the projector. Therefore, for appropriate care and use of
the projector, regular cleaning of the air filters is necessary.
How often the air filters should be cleaned really depends upon the environment in which the projector is being
operated. As a rough guide, under a normally clean operating environment, the air filters should be cleaned
approximately every 200 hours of use. However, if the projector is being operated in a somewhat dusty or
smoky environment, the air filters should be cleaned more often; for consistently good projector operation and
performance, timely cleaning of the air filters is a very important factor. When appropriate, clean the air filters
following the steps below.
Turn off the projector and unplug the AC power cord from an
AC outlet.
1
A
B
Turn over projector and remove the air filters by pulling the
latches upward.
2
Clean the air filters with a brush or rinse them softly. When
rinsing the air filters, dry them well.
3
Replace the air filters properly. Make sure that the air filters
are fully inserted to the projector.
4
CAUTION
AIR FILTERS
Do not operate the projector with the air filters
Pull up and remove.
removed. Dust may accumulate on the LCD Panel and
projection mirror degrading the picture quality. Do not
put anything into the air intake vents. It may result in
malfunction of the projector.
NOTE: If the dust cannot be removed by
cleaning, it is probably time to replace
the air filters with new ones. Please
consult your dealer.
Air Filter (A) Parts No. 610 303 8773
Air Filter (B) Parts No. 610 303 8780
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments
may cause a poor image quality.
When using the projector under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical
elements inside the projector. Such condition may degrade the quality of the projected image.
When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean the projection lens:
Turn off the projector and unplug the AC power cord from an AC outlet.
1
Apply a non-abrasive camera lens cleaner to a dry soft cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents ,or other harsh chemicals might scratch the surface of the lens.
2
Gently wipe with the cleaning cloth over the projection lens.
3
When the projector is not in use, put the lens cap.
4
47
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
When the projection lamp of this projector reaches its
end of life, the LAMP REPLACE indicator lights yellow. If
this indicator lights yellow, replace the projection lamp
with a new one promptly.
TOP CONTROL
This indicator lights yellow
when the projection lamp
reaches its end of life.
Replace the projection lamp
with a new one promptly.
CAUTION
Allow the projector to cool for at least 45 minutes
before you open the lamp cover. The inside of the
projector can become very hot.
CAUTION
For continued safety, replace with a lamp
assembly of the same type.
Do not drop the lamp assembly or touch a glass
bulb! The glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
Turn off the projector and unplug the AC power cord.
Allow the projector to cool for at least 45 minutes.
1
Loosen the two (2) screws with a screwdriver and open
the lamp cover.
2
Loosen the two (2) screws with a screwdriver and pull out
the lamp assembly by using the built in handle.
3
LAMP COVER
Replace the lamp assembly with a new one and tighten
the two (2) screws. Make sure that the lamp assembly is
set properly. Put back the lamp cover and tighten the two
(2) screws.
LAMP
ASSEMBLY
HANDLE
4
Connect the AC power cord to the projector and turn on
the projector.
5
Reset the Lamp replacement counter (refer to”LAMP
REPLACE COUNTER” on the next page).
6
NOTE:
• Do not reset the Lamp replacement counter when the projection lamp is
not replaced.
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
● Model No. of your projector
:
:
PLC-XP57L
● Replacement Lamp Type No.
POA-LMP101
(Service Parts No. 610 328 7362)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACE COUNTER
Be sure to reset the Lamp replacement counter after the lamp assembly is replaced. When the Lamp
replacement counter is reset, the LAMP REPLACE indicator stops lighting.
Lamp counter
Turn the projector on and press the MENU button to display
the On-Screen Menu. Press the POINT LEFT/RIGHT buttons
to move the red frame pointer to the SETTING Menu icon
1
2
3
Press the POINT UP/DOWN buttons to move the red frame
pointer to Lamp counter and then press the SELECT button.
The next box appears.
Press the POINT UP/DOWN buttons to select Reset and then
press the SELECT button. The “Lamp replacement counter
reset?” appears. Move the pointer to [Yes] and then press the
SELECT button.
Select Lamp counter and this box
appears. Select [Reset], and the
next box appears.
Another confirmation dialog box appears and select [Yes] to
reset the Lamp replacement counter.
4
Select [Yes], and then another
confirmation box appears.
NOTE:
• Do not reset the Lamp replacement counter until after the projection lamp is
replaced.
Select [Yes] again
to reset the lamp
counter.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow
carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the
lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
● Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have connected the projector to your computer or video equipment as described in
“CONNECTING PROJECTOR” on pages 12–14.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly
connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the
projector. Turn on equipment in the order of the projector and computer.)
6. If a problem still persists, check the following solutions.
Problem:
No power.
Try these Solutions
● Plug the power cord of the projector into an AC outlet.
● Make sure the READY indicator lights.
● Wait 90 seconds after the projector is turned off to restart the projector.
NOTE: After pressing the POWER ON-OFF button to “OFF”, make sure the projector works
as follows:
1. LAMP indicator lights bright and the READY indicator turns off.
2. After 90 seconds, the READY indicator lights green again and the projector may
be turned on by pressing the POWER ON-OFF button.
● Check the WARNING TEMP. and READY indicators. If both indicators blink, the projector
cannot be turned on.
(See “TURNING ON/OFF PROJECTOR” on pages 20–21.)
● Check the projection lamp. (See page 48.)
● Adjust the focus of the projector.
● Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.
● Check the projection lens to see if it needs cleaning.
Image is out of
focus.
NOTE: Moving the projector from a cool to a warm place may result in moisture
condensation on the projection lens. If this happens, leave the projector off and wait
until condensation evaporates.
● Check the Ceiling/Rear function. (See page 40.)
Picture is left/right
reversed.
● Check the Ceiling function. (See page 40.)
Picture is top/bottom
reversed.
● Check the Display function.(See page 38.)
Some displays are
not seen during
operations.
● Check the connection between your computer or video equipment and the projector.
● When turning the projector on, it takes about 30 seconds to display the image.
● Check the system you selected is corresponding to your computer or video equipment.
● Make sure the temperature is not out of specified operating temperature (41˚F–95˚F
[5˚C–35˚C]).
No image.
● Check the audio cable connection from an audio input source.
● Adjust the audio source.
No sound.
● Press the VOLUME (+) button.
● Press the MUTE button.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote control does
not work.
Try these Solutions
● Check the batteries.
● Check if the ALL-OFF switch on the remote control is set to “ON.”
● Make sure there is no obstruction in between the Infrared remote receiver of the projector
and the remote control.
● Make sure you are not too far from the projector when using the remote control.
Maximum operating range is 16.4’ (5 m).
● Check the remote control code in the remote control.
(See page 41.)
● Check the cable connection between the projector and your computer.
● Check the mouse setting on your computer.
● Turn the projector on before turning on a computer.
Wireless mouse
function does not
work.
SERVICE
WARNING:
High voltages are used to operate this projector. Do not attempt to open the cabinet.
You can usually correct operating problems by yourself. If the projector fails to work properly, see
“TROUBLESHOOTING” on pages 50–51 and try “Solutions” to correct failures.
If you find that service is necessary after following all operating instructions, contact the Sanyo Service Station or
a store where you purchased the unit.
Specify the model number and explain about the problem. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty, and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MENU TREE
Computer Input/Video Input
(1)
Input 1
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Monitor out
Video
Go to System
Input
(2)
(3)
(1)
(2)
(3)
(2)
Input 2
Input 3
Go to System
Go to System
Go to System
Go to System
Go to System
Go to System
Y, Pb/Cb, Pr/Cr
RGB
Video
Y, Pb/Cb, Pr/Cr
S-Video
Computer Input
(1)
Mode 1
Mode 2
SVGA 1
SVGA 2
SVGA 3
Standard
Real
System
Image Select
Image 1
Image 10
✽ System displayed in the System Menu varies depending on the input signal.
Auto PC adj.
Normal
PC Adjust
Screen
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
0–31
True
Wide
Full
Digital zoom +
Digital zoom -
Display area - H
Display area - V
Reset
Yes/No
Mode free
Store
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Quit
Quit
52
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Video Input
Computer Input/Vide Input
(2)
Auto
Language
English
German
French
Italian
System
System
Setting
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
Spanish
Portuguese
Dutch
Swedish
(3)
Auto
1080i
1035i
720p
575p
480p
575i
Russian
Chinese
Korean
Japanese
Quit
Keystone
Background
Display
Store/Reset
Blue/User/Black
Off/Countdown Off/On
480i
Logo
Logo select
Standard
Cinema
Image 1
Capture
Image Select
Logo PIN code lock
On/Off
Logo PIN code change
Quit
Image 10
Quit
Ceiling
On/Off
On/Off
On/Off
On/Off
Normal
Wide
Rear
Screen
Anamorphic
Simple menu
Menu position
Power management
Off
Computer Input/Vide Input
Ready
Shut down
1–30 Min.
Quit
Contrast
0–63
Image Adjust
Brightness
Color
0–63
0–63
Tint
0–63
On start
On/Off
Color management
Color
Lamp control
Auto/Normal/Eco
Gamma
List
Remote Control
All Del
Code 1
Color M.
Menu
Off/L1/L2
High
Menu
Color M.
Code 8
Quit
Auto picture control
Color temp.
USB
Mouse
Projector
Mid
Low
Security
Key lock
Off
XLow
0–63
Projector
Remote Control
Quit
Red
Green
0–63
Blue
0–63
Sharpness
Gamma
Noise reduction
Progressive
Reset
0–31
PIN code lock
Off/On1/On2
PIN code change
Quit
0–15
Off/L1/L2
Off/On/Film
Yes/No
Image 1
Lamp counter
Factory default
Quit
Yes/No
Yes/No
Store
Image 10
Quit
Quit
Volume
Built-in SP.
Mute
0–63
Sound
On/Off
On/Off
Quit
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V-, H-Frequency mentioned below, and less
than 140 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480i
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
31.47
31.25
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
60.24
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
60.00
50.00
59.88
50.00
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
77.07
75.70
86.96
58.20
58.30
72.00
75.08
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
SXGA 19 1280 x 1024
SXGA 20 1280 x 1024
SXGA 21 1400 x 1050
SXGA+ 1 1400 x 1050
SXGA+ 2 1400 x 1050
SXGA+ 3 1400 x 1050
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.90
63.97
65.35
65.12
75.00
80.00
48.36
47.70
48.36
56.16
75.00
81.25
87.50
93.75
45.00
37.50
33.75
33.75
28.125
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
86.00
94.00
60.01
72.00
66.00
86.70
60.18
85.024
60.00
60.19
60.12
59.90
75.08
75.08
60.00
60.00
60.00
72.00
60.00
65.00
70.00
75.00
60.00
50.00
60.00
60.00
50.00
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Progressive)
––––––––
(Progressive)
575i
480p
575p
1280 x 1024
(Interlace)
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
(Interlace)
1152 x 900
1280 x 1024
(Interlace)
MAC
MAC
1280 x 960
1280 x 1024
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
WXGA 1
WXGA 2
WXGA 3
WXGA 4
UXGA1
UXGA2
UXGA3
UXGA4
720p
720p
1035i
1080i
1080i
1024 x 768
(Interlace)
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
MAC 19
1024 x 768
1024 x 768
––––––––
(Progressive)
––––––––
(Progressive)
––––––––
(Interlace)
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
1024 x 768
––––––––
(Interlace)
––––––––
(Interlace)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
When a input signal is digital from DVI terminal, refer to the chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
✳
✳
D-VGA
D-480p
D-575p
D-SVGA
D-XGA
640 x 480
31.47
31.47
31.25
37.879
43.363
48.36
47.70
48.36
46.50
63.98
59.94
59.88
50.00
60.32
60.00
60.00
60.00
60.00
50.00
60.02
D-SXGA2
D-SXGA+ 1
D-720p
1280 x 1024
1400 x 1050
60.276
63.97
45.00
37.50
33.75
33.75
28.125
33.75
28.125
27.00
58.069
60.19
60.00
50.00
60.00
60.00
50.00
60.00
50.00
48.00
720 x 480
(Progressive)
1280 x 720
768 x 575
(Progressive)
(Progressive)
1280 x 720
(Progressive)
D-720p
800 x 600
1920 x 1035
(Interlace)
D-1035i
1024 x 768
1920 x 1080
(Interlace)
D-1080i
D-WXGA1 1366 x 768
D-WXGA2 1360 x 768
D-WXGA3 1376 x 768
D-WXGA5 1368 x 768
D-SXGA1 1280 x 1024
1920 x 1080
(Interlace)
D-1080i
D-1080psf/30
D-1080psf/25
D-1080psf/24
1920 x 1080
1920 x 1080
1920 x 1080
✳
✳ Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
NOTE: Specifications are subject to change without notice.
INDICATORS AND PROJECTOR CONDITION
Check the indicators for projector condition.
Indicators
WARNING
TEMP.
red
LAMP
REPLACE
yellow
Projector Condition
READY
green
LAMP
red
The projector is OFF. (The AC power cord is unplugged.)
The projector is ready to be turned on with the POWER ON-
OFF button.
✽
✽
The projector is operating normally.
The Warning Temp. indicator blinks red to let you know the
internal temperature of the projector exceeds a normal level. If
the temperature goes up further, the projector will be turned
off automatically and the Ready indicator goes out. When the
projector is cooled down enough and the temperature returns
to normal, the READY indicator lights green and the projector
can be turned on again. (The WARNING TEMP. indicator
keeps blinking.) Check and clean the air filters.
✽
The projector is cooled down enough and the temperature
returns to normal. When turning on the projector, the
WARNING TEMP. indicator stops blinking. Check and clean
the air filters.
✽
• • • on
• • • blinking
• • • dim
• • • off
55
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Indicators
WARNING
READY
TEMP.
green
LAMP
REPLACE
yellow
Projector Condition
LAMP
red
red
The projector is in cooling mode. It cannot be turned on until
the READY indicator lights green.
✽
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC power cord and plug it again to turn
on the projector. If the projector is turned off again, disconnect
the AC power cord and contact the dealer or the service
center for service and checkup. Do not leave the projector on.
It may cause electric shock or a fire hazard.
The projector is in the Power management mode.
✽
✽
The temperature inside the projector is abnormally high.
The lamp cannot light up. (The projector is preparing for
stand-by or the projection lamp is in cooling mode. The
projector cannot be turned on until the cooling process is
completed.)
The lamp cannot light up. (The lamp has been cooled down
enough and the projector is in stand-by mode and ready to be
turned on with the POWER ON-OFF button.)
The projection lamp reaches its end of life.
Replace the lamp and then reset the Lamp replacement
counter. The indicator is turned off.
✽
• • • on
• • • blinking
• • • dim
• • • off
*When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator
lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replacement counter after
replacing the lamp.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
12.6” x 6.6” x 16.8” (319 mm x 168 mm x 429.5 mm)
17.4 lbs (7.9 kg)
(W x H x D)
Dimensions
Net Weight
1.3” TFT Active Matrix type, 3 panels
1024 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 kHz–100 kHz, V-sync. 48–100 Hz
Up and Down
High Definition TV Signal
Scanning Frequency
Motorized Lens Shift
Horizontal Resolution
Projection Lamp
Input 1 Jacks
800 TV lines (HDTV)
300 watt type
DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H/V, and V),
Stereo Mini Type Jack (Audio)
Input 2 Jacks
Input 3 Jacks
Other Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack
and PJ-Net Organizer Connector
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
0˚ to 10.5˚
Built-in Speakers
Feet Adjustment
Voltage and Power
Consumption
AC 100–120 V (5.7 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200–240 V (2.7 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
41˚F–95˚F (5˚C–35˚C)
Operating Temperature
Storage Temperature
14˚F–140˚F (-10˚C–60˚C)
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA or LR6 ALKALINE Type x 2
16.4’ (5 m) / 30˚
2.0” x 1.4” x 7.6” (50 mm x 36 mm x 193 mm)
0.35 lbs (160 g) (including batteries)
Remote Control Transmitter
(Max. Output: 1mW/Wave length: 650 20nm)
Class II Laser
Owner’s Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Accessories
Wireless/Wired Remote Control Transmitter and Batteries
VGA Cable
USB Cable
Control Cable for Serial Port
Lens Attachment
Lens Replacement And Installation Manual
PIN Code Label
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are
effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
● Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by side, you may recognize different
white balance and color uniformity on each projector.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINALS (ANALOG)
Terminal: HDB15-PIN
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
+5V Power
Pin Configuration
10 Ground (Vert. sync.)
11 Sense 0
12 DDC Data
2
1
5
4
3
10
9
8
7
6
15
Ground (Horiz.sync.) 13 Horiz. sync.
14
13
12
11
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 DDC Clock
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal: DVI 24-pin
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
Pin Configuration
10 T.M.D.S. Data1+
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
1
9
2
3
4
5
6
7
8
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)
16 Hot Plug Detect
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
No Connect
CONTROL PORT CONNECTOR
Terminal: Mini DIN 8-PIN
PS/2
-----
Serial
R X D
-----
ADB
-----
Pin Configuration
1
2
3
4
5
6
7
8
CLK
DATA
GND
-----
ADB
-----
-----
8
7
6
GND
GND
-----
5
4
3
RTS/CTS
T X D
GND
2
1
-----
-----
GND
-----
-----
GND
GND
USB CONNECTOR (Series B)
Pin Configuration
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
58
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, specify the item name and its Type
No. to the sales dealer.
● HDB 15 pin-SCART 21 pin Cable Type No. : POA-CA-SCART
● Standard Zoom Lens
● Long Zoom Lens
Type No. : LNS-S30
Type No. : LNS-T31A
Type No. : LNS-T32
● Ultra Long Zoom Lens
● Short Zoom Lens
● Short Fixed Lens
Type No. : LNS-W31A
Type No. : LNS-W32
Type No. : POA-CA-RC30
Type No. : POA-PN03
Type No. : POA-FBOX-130
● Remote Control Cable
● PJ-Net Organizer
● External Air Filter Kit
LENS REPLACEMENT
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector
for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by
yourself as it may cause injury.
After installing the lens, attach the lens cap to the lens when setting up the projector.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.
To the sales and service engineers:
Referring to the attached lens replacement and installation manual, replace or install the lens properly.
PJ LINK NOTICE
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information
System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified
conformance with PJLink Standard Class 1.
SANYO Projector Input
PJLink Input
RGB 1
Parameter
Input1
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Video
11
12
31
32
21
22
13
23
24
25
RGB 2
DIGITAL 1
DIGITAL 2
VIDEO 1
VIDEO 2
RGB 3
Input2
Input3
Y, Pb/Cb, Pr/Cr
RGB
Video
VIDEO 3
VIDEO 4
VIDEO 5
Y, Pb/Cb, Pr/Cr
S-video
PJLink is a registered trademark of JBMIA.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
PIN CODE NUMBER MEMO
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost
the number and unable to use the projector, contact the service station.
PIN Code Lock No.
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
* Should the four-digit number be
changed, the factory set number will
be invalid.
While the projector is locked with the PIN code...
Put on the label below (supplied) in a prominent place of the
projector’s body while it is locked with a PIN code.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
DIMENSIONS
12.6 (319.0)
5.59 (142.0)
Unit : inch (mm)
2.39 (60.6)
4.55 (115.5)
4.61 (117.0)
Screw Holes for Ceiling Mount
Screw: M6
Depth: 0.393 (10.0)
3.74 (95.0)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYO Electric Co., Ltd.
1AA6P1P5225-- KE6A
Download from Www.Somanuals.com. All Manuals Search And Download.
|