Sanyo Flat Panel Television LCE 24C100FK User Guide

INSTRUCTION MANUAL  
LCE-24C100F(K)  
LCE-24C100F(N)  
LCE-24C100F(R)  
LCE-24C100F(S)  
LED LCD TV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Before operating this LCD TV, read this manual thoroughly and operate the LCD TV properly. This LCD TV provides many convenient  
features and functions. Operating the LCD TV properly enables you to manage those features and maintains it in better condition for a  
considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.  
If your LCD TV seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the  
“Troubleshooting” section on page 17 of this booklet. If the problem still persists, contact the dealer where you purchased the LCD TV or the  
service center.  
Safety Precaution  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN  
OR MOISTURE.  
WARNING :  
Install the LCD TV in a proper position. If not, it may result in a fire hazard.  
Provide appropriate space on the top, sides and rear of the LCD TV cabinet for allowing  
air circulation and cooling the LCD TV. Minimum clearance must be maintained. If the  
LCD TV is to be built into a compartment or similarly enclosed, the minimum distances  
must be maintained. Do not cover the ventilation slot on the LCD TV. Heat build-up can  
reduce the service life of your LCD TV, and can also be dangerous.  
If the LCD TV is not to be used for an extended time, unplug the LCD TV from the power  
outlet.  
SIDE and TOP  
10 cm  
REAR  
6 cm  
10 cm  
10 cm  
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.  
Caution In Installing  
Handle the  
carefully when installing it and do not drop.  
LCD TV  
Locate set away from heat, excessive dust, and direct sunlight.  
For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow correct mounting  
procedures could result in damage to the equipment or injury to the installer.  
NOTE :  
When LCD TV is not used for a long period of time, unlighted dots may be observed. This is caused by characteristic of the LCD TV. If this  
occurs, turn the LCD TV on and leave it on about 1 hour. These dots will gradually disappear.  
T H I S S Y M B O L I N D I C AT E S T H AT  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
DISPOSAL PRECAUTIONS  
DANGEROUS VOLTAGE CONSTITUTING  
R I S K O F E L E C T R I C S H O C K  
A
I S P R E S E N T W I T H I N T H I S U N I T.  
CONTAINS MERCURY  
LAMPS, DISPOSE OF  
PROPERLY  
THIS SYMBOL INDICATES THAT THERE  
A R E I M P O RTA N T O P E R AT I N G A N D  
MAINTENANCE INSTRUCTIONS IN THE  
OWNER'S MANUAL WITH THIS UNIT.  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE  
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
All the safety and operating instructions should be read before the product is operated.  
Read all of the instructions given here and retain them for later use. Unplug this LCD TV from AC power supply before cleaning. Do not use  
liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the LCD TV. For added protection to  
the LCD TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will  
prevent damage due to lightning and power line surges.  
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the manufacturer as they may cause hazards.  
Do not place this LCD TV on an unstable cart, stand, or table. The LCD TV may fall, causing serious injury to a child or adult,  
and serious damage to the LCD TV. Use only with a cart or stand recommended by the manufacturer, or sold with the LCD  
TV. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the  
manufacturers.  
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause  
the appliance and cart combination to overturn.  
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and  
to protect it from overheating. The openings should never be covered with cloth or other materials, and the bottom opening should not  
be blocked by placing the LCD TV on a rug, or other similar surface. This LCD TV should never be placed near or over a radiator or heat  
register. This LCD TV should not be placed in a built-in installation such as a book case unless proper ventilation is provided. Never push  
objects of any kind into this LCD TV through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a  
fire or electric shock. Never spill liquid of any kind on the LCD TV. Do not place items such as vases containing liquid on top of the LCD TV.  
Do not install the LCD TV near the ventilation duct of air-conditioning equipment.  
This LCD TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power  
supplied, consult your authorized dealer or local power company.  
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord.  
Do not locate this LCD TV where the cord may be damaged by persons walking on it.  
Do not attempt to service this LCD TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer  
all servicing to qualified service personnel.  
Unplug this LCD TV from wall outlet and refer servicing to qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilLCD into the LCD TV.  
c. If the LCD TV has been exposed to rain or water.  
d. If the LCD TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the  
operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified  
technician to restore the LCD TV to normal operation.  
e. If the LCD TV has been dropped or the cabinet has been damaged.  
f. When the LCD TV exhibits a distinct change in performance-this indicates a need for service.  
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the  
same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.  
Upon completion of any service or repairs to this LCD TV, ask the service technician to perform routine safety checks to determine that the  
LCD TV is in safe operating condition.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE  
FEATURE AND DESIGN.......................................4  
PREPARATION........................................5  
PICTURE MODE  
SPORTS MODE  
OFF TIMER  
WIDE  
10  
10  
10  
10  
PART NAMES AND FUNCTIONS  
5
CONNECTING LCD TV......................6  
INSTALLING & UNINSTALLING  
MENU OPERATION............................................... 11  
STAND BASE  
6
6
7
CHANNEL  
PICTURE  
SOUND  
11-12  
12  
CONNECTING AC POWER CORD  
CONNECTING A COMPUTER  
CONNECTING VIDEO EQUIPMENT &  
AERIAL  
13  
TIMER  
13  
7
OSD  
13  
BASIC OPERATION.............................................8  
SETUP  
14  
OPERATION OF REMOTE CONTROL  
REMOTE CONTROL BATTERIES  
INSTALLATION  
8
SETUP (PC MODE)  
DEALER MODE  
14-15  
15-16  
8
8
APPENDIX..............................................................16  
CLEANING LCD TV 16  
FUNCTION OF PRODUCT SAFETY FEATURE 16  
TURNING ON/OFF LCD TV  
PLUG & PLAY  
9
SELECTING INPUT SOURCE  
CHANNEL RECALL  
CHANNEL SELECTION  
INFO  
9
TROUBLESHOOTING  
17  
18  
19  
9
9
TECHNICAL SPECIFICATIONS  
SIGNAL MODE COLUMN (Recommended)  
10  
10  
10  
10  
10  
VOLUME CONTROL  
MUTE  
STEREO/MONO  
SOUND MODE  
is registered trademarks of HDMI Licensing, LLC.  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.  
Feature and Design  
¡ Picture  
SHOP Mode  
Picture mode will be Dynamic and ECO mode  
will be OFF in SHOP MODE.  
High Definition LCD with LED Backlight Panel  
1920 x 1080 pixel FHD LCD LED Backlight Panel with high  
contrast ratio and wide viewing angle.  
¡ Compatibilty  
VIZON Engine  
Full Multi System  
VIZON Engine, SANYO High Quality Image Processing  
Technology reproduces clear, dynamic, natural and realistic  
picture along with FHD LCD Panel Technology.  
PAL, SECAM, NTSC, NTSC 4.43 system can be connected.  
HD-Ready  
1080p, 1080i, 720, Full High Definition signals are receivable.  
Dynamic AI  
HDMI  
HDMI provides complete transmission of digital  
image and sound signals without any quality deterioration.  
DVI can be connected to HDMI.  
PC Input  
Personal Computer/Laptop can be connected with automatic  
resolution adjustment.  
The AI (Automatic Image Control) circuit compensates picture  
contrast and brightness level dynamically and reproduces bright  
and high-contrast picture.  
¡ Sound  
NICAM/A2 Stereo  
It's the Stereo Sound PAL Color TV Broadcasting System upgrading  
mono-sound TV service to stereo or dual-language sound.  
Terminals  
HDMI for BluRay Player etc.  
D-SUB 15-pin for PC input etc.  
Component Video for DVD  
Video for VCR/DVD  
Bass Expander  
Bass Expander reinforces bass effect to improve overall sound quality.  
¡ Feature  
¡ Others  
Sports Mode  
Just by pressing the button, sports mode optimizes picture and sound  
settings suitable for each sports program.  
ƒ OFF  
Normal setting.  
ƒ Football  
Use to watch football program, golf program or etc.  
ƒ Winter Sport  
Suitable setting for skiing program or etc.  
ƒ Marine Sport  
Wall Mounting  
It's designed for VESA Standard (200 x 200) wall hanging bracket.  
Light Commercial Mode  
By entering Dealer mode, Volume Lock, Tuning Lock, Start Mode,  
OSD, RC, AC Power Mode, Start Volume Level, Music Mode and  
Reset can be selected.  
Convenient for placing in Hotel, Hospital, School, Store, Bank etc.  
Suitable setting for swimming, diving program or etc.  
ƒ Indoor Sport  
Suitable setting for basketball, badminton program or etc.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
PART NAMES AND FUNCTIONS  
FRONT  
Panel  
Side Control  
Infrared  
Remote  
Receiver  
Power/Timer  
Indicator  
CARE FOR USING LCD TV  
Do not bump or scratch the panel surface as this causes flaws on the surface of the screen.  
There may be some tiny black points and/or bright points on the SCREEN. These points are normal.  
SIDE CONTROL  
POWER ON/ OFF button  
-Used to turn the LCD TV on or off.  
MENU button  
-Open or close the On-Screen Menu.  
INPUT MODE button  
Used to select input source: TV/AV1/ AV2(DVD) /HDMI(DVI)/PC.  
-Used to confirm the selected item on On-Screen Menu.  
VOLUME buttons  
Each button on the control  
panel has the same function  
with its counterpart on the  
remote control.  
-
(+/-)  
-Used to adjust the volume.  
-Used to adjust the value of the selected item on On-Screen Menu.  
-Used to execute the selected item on On-Screen Menu.  
(
) buttons  
CHANNEL UP/DOWN /▼  
-Used to Change channels.  
-Used to select items on On-Screen Menu.  
BACK TERMINAL  
HDMI Input Terminal  
Connect video and audio outputs  
from video equipment.  
PC Input Terminals  
Connect computer outputs to these  
terminals.  
RGB (D-SUB)  
Audio (L/R)  
AV1 Terminals  
Connect video and audio outputs from  
video equipment.  
Video (RCA type)  
AV2 Terminals  
Connect video and audio outputs  
from video equipment.  
DVD component (RCA type)  
Audio L and R (RCA type)  
Audio L and R (RCA type)  
Monitor Output Terminals  
Aerial Jack  
Connect a television, video recorder or  
external audio amplifier to these jacks.  
Video (RCA type)  
Connect the cable with a plug from  
aerial jack to the aerial socket on  
the cabinet back.  
Audio L and R (RCA type)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING LCD TV  
INSTALLING & UNINSTALLING STAND BASE  
Please according to the following procedure to install stand.  
Be careful of the panel. Suggest to put down the panel side on the cushion or other soft material before installing  
the stand.  
1
To align the corresponding pilot holes and fix the stand by screws.  
Screws (M4x8) for LCE-24C100F(K)/(N)/(R)/(S): 2 pcs  
2
Installing of stand is completed.  
Screw M4 X 8 :  
3
Model LCE-24C100F(K)/(N)/(R)/(S):  
Screw : M4 X 8  
Screw : M4 X 8  
CAUTION IN INSTALLING & UNINSTALLING STAND BASE  
Through in installing or uninstalling work, handling with more than two people is recommended.  
When holding (moving or lifting) the LCD Display, hold the display's body. Do not handle the LCD TV by holding the attached accessory parts,  
otherwise it may result in damage.  
Before installing or uninstalling, provide a desk (or a part of it) which is strong enough to support the weight of the LCD TV and this stand. The  
desk must be larger than the LCD Display screen size. The desk's surface must be flat and maintained with soft material (such as a blanket) for  
protecting the screen surface.  
Before putting the LCD Display on the desk, make sure there is no object on it. Leaving any object under the screen may cause damage on the  
screen.  
The LCD TV with this stand should be installed or uninstalled on flat and level place. Do not place on such as a non flat, unlevel or unstable cart or  
stand. The display may fall, causing not only serious damage to the products but serious injury to a person.  
SAFETY NOTE  
For correct installing, mounting and uninstalling LCD TV Stand, it is strongly recommended to use a trained, authorized dealer. Failure to follow  
correct procedures could result in damage to the equipment or injury to the installer.  
CONNECTING AC POWER CORD  
This LCD TV uses nominal input voltages of 110-240V AC. This LCD TV  
automatically selects the correct input voltage. It is designed to work with single-  
phase power systems. To reduce risk of electrical shock, do not plug into any  
other type of power system. Consult your authorized dealer or service station if  
you are not sure of the type of power being supplied.  
Connect the LCD TV with all peripheral equipment before turning the LCD TV on.  
Note:  
AC Power Cord types vary between countries.  
CAUTION  
For safety, unplug AC power cord when the LCD  
TV is not in use.  
AC POWER CORD  
To the AC Outlet (110 - 240V AC).  
Pulls the AC power cord out from  
the LCD TV. The AC outlet must be  
near this equipment and must be  
easily accessible.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING LCD TV  
CONNECTING A COMPUTER  
Cables used for connection (These cables are not  
supplied with this LCD TV.)  
PC/VGA Cable (D-SUB 15pin)  
HDMI Cable: HDMI Input  
MAC Adapter (in the case of connecting Macintosh  
computer)  
NOTE:  
When connecting the cables, AC Power Cords  
of both LCD TV and external equipment should  
be disconnected from AC outlet. Turn LCD  
TV and peripheral equipment on before your  
computer is switched on.  
Audio Cable [Mini Plug (L/R)]  
Desktop  
type  
Laptop  
type  
IBM-compatible  
computers  
Monitor Output  
PC Input  
or Macintosh  
computers  
MAC  
Adapter  
(VGA / SVGA /  
XGA )  
HDMI Output  
HDMI Input  
Note:  
1. You can connect the DVI source to HDMI input  
terminal by using the DVI to HDMI converter.  
2. When inputting 1080p signal to HDMI terminal,  
please use High Speed HDMI Cables to avoid  
picture/ sound noise and no picture/sound.  
3. When connect to HDMI Input terminal, it needs few  
seconds to display picture.  
Audio Output  
(stereo)  
Audio Input  
(stereo)  
CONNECTING VIDEO EQUIPMENT & AERIAL  
Component Video Source  
(example)  
Cables used for connection (These cables are not supplied with this LCD TV.)  
Video Cable(RCA X1), Audio Cable (RCA X2) : Video 1 or Video 2  
Video Cable(RCA X3), Audio Cable (RCA X2) : DVD (Component Video)  
Video Cable(RCA X1), Audio Cable (RCA X2) : Monitor Output  
HDMI Cable: HDMI Input  
DVD video equipment.  
(such as DVD player or high-definition  
TV source)  
DVD Player  
Video 1 signal is output from AV1 terminals;  
Video 2 signal is output from Y/L/R terminals of AV2.  
R
L
CR/PR,CB/PB, Y  
NOTE : When connecting the cable, AC Power Cords  
of both LCD TV and external equipment should  
be disconnected from AC outlet.  
DVD  
(RCA X 3)  
Audio cable  
(RCA X 2)  
MONITOR OUT  
Note:  
Video (RCA) output is for  
TV, or AV only.  
Audio Amplifier  
Composite Video  
and Audio Output  
Video cable  
(RCA x1)  
Audio  
Speaker  
(stereo)  
Outdoor Aerial  
Audio cable  
(RCA x 2)  
External  
monitor  
External Audio  
Equipment  
Video and Audio  
cable (RCA x 3)  
Aerial Cable  
Video Source (example)  
Video Disc  
Player  
Video Cassette  
Recorder  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
OPERATION OF REMOTE CONTROL  
POWER ON/OFF button  
SOUND button  
INPUT button  
INFO / VA·B button  
PICTURE button  
WIDE button  
SPORTS button  
TIMER button  
NUMERIC buttons  
CHANNEL UP/DOWN buttons  
CHANNEL RECALL button  
VOLUME +/- buttons  
MUTE button  
BACK button  
DIGIT button  
MENU button  
ENTER button  
▼ ◄  
/ /buttons  
POINT /  
REMOTE CONTROL BATTERIES INSTALLATION  
Remove the battery compartment cover.  
1
Insert two size AA batteries (1.5V) according to "+" and "-" polarity markings inside  
the battery compartment.  
2
Close the battery compartment cover.  
3
Note:  
Do not expose batteries (battery pack or batteries installed) to excessive heat such  
as sunshine, fire or the like.  
TURNING ON / OFF LCD TV  
SIDE CONTROL  
Complete the peripheral connections before turning on LCD TV. (Please refer to "CONNECTING  
1
LCD TV".)  
Connect LCD TV's AC Power Cord into an AC outlet.  
2
3
POWER ON/ OFF  
button  
Press POWER ON/OFF button on Side Controls of LCD TV or on  
Remote Control to turn it ON. The POWER indicator will light up  
(green). Press POWER ON/OFF button again to shift it to stand-by  
status, the POWER indicator will become red.  
REMOTE CONTROL  
NO SIGNAL SHUT OFF  
This TV set incorporates the NO SIGNAL SHUT OFF function.  
If no signal is input in TV mode, "OFF 00:10" will display for about 10 minutes and TV will be  
turned off automatically.  
POWER ON/  
OFF button  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
PLUG & PLAY  
By PLUG & PLAY, when the TV reset and powered on for the first time, it will automatically  
search and preset all the receivable TV programs.  
I AM SEARCHING ALL PROGRAMMES  
PLEASE WAIT!  
Plug the power, connect the antenna, and press Main Power ON/OFF button, the TV set will  
1
1
automatically search the programs.  
MENU  
:
CANCEL  
After programs searching, SHOP MODE menu will appear. Press POINT ◄► buttons to select  
2
and press ENTER button for SHOP MODE or HOME MODE. Then the pop up menu disappears.  
Auto searching completed and message "AUTO SET-UP COMPLETED HAPPY VIEWING!"  
appears. About 5 seconds later, the TV set will automatically return to programme position “1”.  
3
PLEASE SELECT AND PRESS ENTER BUTTON  
HOME MODE SHOP MODE  
Message "NO STATION PLEASE CONNECT ANTENNA PLUG!" will appear if there is no TV stations  
are searched after automatically programs searching.(see Figure A.) Then SHOP MODE menu  
appears, the same operations as step 2 above will be excuted and returns to normal TV picture.  
Press MENU button while searching programs, message "PLEASE SELECT AND PRESS ENTER  
BUTTON" appears (see Figure B), press POINT◄► buttons to select "TEMPORAL CANCEL" or  
"PERMANENT CANCEL".  
:
SELECT  
:
ENTER  
ENTER  
AUTO SET-UP COMPLETED  
HAPPY VIEWING!  
TEMPORAL CANCEL to cancel temporary PLUG & PLAY function. The PLUG & PLAY function is  
actived only in TV mode while turning on the LCD TV.  
Figure A.  
PERMANENT CANCEL to cancel permanetly PLUG & PLAY function. When turn on television the  
PLUG & PLAY is not actived. Press ENTER button to enter SHOP MODE menu. the same operations  
as step 2 above will be excuted and returns to normal TV picture.  
NO STATION  
PLEASE CONNECT ANTENNA PLUG!  
Figure B.  
PLEASE SELECT AND PRESS ENTER BUTTON  
TEMPORAL CANCEL PERMANENT CANCEL  
:
SELECT  
ENTER  
:
ENTER  
SELECTING INPUT SOURCE  
Select mode "TV", "AV1", "AV2", "HDMI" or "PC" by pressing INPUT button on Remote Control or on Side Controls, you can also press  
POINT ▲▼ buttons to select different mode. To enter the selected mode, press ENTER button or POINT ◄► buttons.  
REMOTE CONTROL  
Note:  
SIDE CONTROL  
INPUT  
1. TV  
2. AV1  
3. AV2  
4. HDMI  
5. PC  
User can directly displayed  
selected input source by  
pressing NUMERIC buttons  
(1-5) on Remote Control.  
INPUT  
button  
INFO  
button  
1~5  
: SELECT  
: EXIT  
INPUT  
button  
BACK  
NUMERIC  
buttons  
CHANNEL RECALL  
Press CHANNEL RECALL button to switch between the previous channel and the current channel.  
For example, now you are watching channel "4", but you watched channel "2" previously. If you  
press CHANNEL RECALL button, channel "2" will appear immediately.  
CHANNEL  
UP/DOWN  
(▲▼) buttons  
CHANNEL SELECTION  
There are 256 channels can be selected on the LCD TV.  
CHANNEL  
RECALL  
button  
DIRECT SELECTION  
For direct access to programmes using the (0-9) numeric buttons.  
1) For selection of channel position 0 - 9. Example: For channel position 8, press “8” button.  
DIGIT  
button  
2) For selection of channel position 10 - 99. Example:  
For channel position 25, press the DIGIT button to display "- -", then press “2” and “5” buttons.  
3) For selection of channel position 100 - 199. Example:  
For channel position 125, press the DIGIT button twice to display "1 - -", then press “2” and “5” buttons.  
4) For selection of channel position 200 - 255. Example:  
For channel position 225, press the DIGIT button three times to display "2 - -", then press “2” and “5”  
buttons.  
CHANNEL UP/ DOWN  
Press CHANNEL UP/DOWN (▲▼) buttons on Side Control or on Remote Control to select programs.  
Press CHANNEL UP () button to select next channel.  
Press CHANNEL DOWN () button to select previous channel.  
Note:  
CHANNEL RECALL and CHANNEL SELECTION function only use in TV mode.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
INFO  
Press INFO button on Remote Control to display the status of LCD TV. Press again to remove the display.  
Channel  
11  
Colour System  
Sound System  
STEREO/MONO  
AUTO  
B/G  
MONO  
VOLUME CONTROL  
To adjust the volume value desired by pressing VOLUME(+/-) buttons on Remote Control or on Side  
Control. The volume dialogue box will appear on the screen for a short while. VOLUME(+) button  
to increase volume, and VOLUME(-) button to decrease volume.  
REMOTE CONTROL  
MUTE  
SOUND button  
VA·B button  
Should you wish to mute the sound, press MUTE button. To switch the sound back on, press  
MUTE button again or press VOLUME(+/-) buttons on Side Control or on Remote Control.  
PICTURE button  
SPORTS button  
STEREO/MONO  
Press the VA·B button on Remote Control to show the information display. And then press VA·B  
button to select the following audio signals: "STEREO", "MONO", "NICAM", "A", and "B".  
SOUND MODE  
Select sound level by pressing SOUND button on Remote Control.  
STANDARD: Normal sound state preset on LCD TV.  
NEWS: Select this mode for talk programs.  
VOLUME(+/-)  
buttons  
MUSIC: Select this mode for music programs.  
PERSONAL: Select this mode for user to call out the preset sound adjustment in SOUND  
menu.  
MUTE button  
PICTURE MODE  
Select image level by pressing PICTURE button on Remote Control.  
STANDARD: Natural and splendid picture level preset on this LCD TV.  
VIVID: Present colourful and lively picture level.  
SOFT: Inhibit strong contrast and color, it is beneficial for eye protection.  
PERSONAL: User presets picture adjustment in PICTURE MODE.  
DYNAMIC: Bright and dynamic picture. It is suitable for nice playback, such as DVD program.  
Note:  
Select ECO in SETUP menu. Then press ◄► buttons to select "ON". While in ECO status, press PICTURE button to choose any of options  
of "ECO LOW/STANDARD", "ECO LOW/VIVID", "ECO LOW/SOFT", "ECO LOW/PERSONAL" and "ECO HIGH/DYNAMIC", or "ECO HIGH/  
STANDARD", "ECO HIGH/VIVID", "ECO HIGH/SOFT", "ECO HIGH/PERSONAL" and "ECO HIGH/DYNAMIC".  
SPORTS MODE  
Just by pressing the button, sports mode optimizes picture and sound settings suitable for each sports program.  
ƒ OFF: Normal setting.  
ƒ Football: Use to watch football program, golf program or etc.  
ƒ Winter Sport: Suitable setting for skiing program or etc.  
ƒ Marine Sport: Suitable setting for swimming, diving program or etc.  
ƒ Indoor Sport: Suitable setting for basketball, badminton program or etc.  
Note:  
Press SOUND button in SPORTS mode, only current SPORTS mode is displayed.  
OFF TIMER  
To set OFF TIMER by pressing TIMER button on Remote  
REMOTE CONTROL  
Control. The timer dialogue box will appear on the screen for a short while.  
To select "OFF", "30 MIN", "60 MIN", "90 MIN" or "120 MIN" with TIMER buttons.  
WIDE button  
TIMER button  
WIDE  
Select screen size among "FULL", "ZOOM", "ZOOM[CAPTION-IN]", and "NORMAL" by pressing WIDE button  
on Remote Control.  
*
*
*
This function doesn't work in TV/ AV/ DVD/ HDMI/ PC modes when no signal is input.  
Only "FULL" mode can be selected when the input mode is "HDMI" or "DVD" and the input signal is 1080i, 720p or 1080p.  
"FULL" and "NORMAL" can be selected in PC mode.  
FULL: Provides image to fit width of screen by expanding image width uniformly. This function can be used  
for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen. When your video equipment  
(such as DVD) has 16 : 9 output mode, select 16 : 9 and select "Full" to provide better quality.  
ZOOM: Provides image to fit screen size (16 : 9 aspect ratio) by expanding image width and height uniformly.  
This function can be used for enjoying a letter box mode picture (4 : 3 aspect picture with black bar on top and  
bottom edges) with wide video aspect of 16 : 9 screen.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION  
ZOOM[CAPTION-In]: Provides the image that is expanded as "ZOOM" mode and moved up to show more  
image to include captions. This function can be used for enjoying a letter box picture with captions.  
NORMAL: Provides real 4 : 3 image on 16 : 9 screen.  
CHANNEL  
Press MENU button and the main menu will appear. Whenever MAIN MENU is accessed initially,  
CHANNEL will be the default selection.  
CHANNEL MENU  
1
Press POINT ▲▼ buttons or ENTER button to enter into CHANNEL menu.  
2
Press POINT ▲▼ buttons to select the item desired.  
CHANNEL  
3
AUTO SEARCH  
Press POINT ◄► buttons to adjust the item.  
SEMI-AUTO SEARCH  
MANUAL SEARCH  
COLOUR SYSTEM  
4
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
AUTO  
SOUND SYSTEM  
SKIP  
B/G  
OFF  
CHANNEL SWAP  
Note:  
"CHANNEL" menu doesn't work in HDMI mode and PC mode.  
In AV mode, only "COLOUR SYSTEM" in "CHANNEL" menu can be selected.  
The settings for "SOUND SYSTEM", "COLOUR SYSTEM" or "SKIP" are automatically memorized in  
the programme position.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
AUTO SEARCH  
AUTO SEARCH MENU  
All receivable channels are automatically tuned in and memorized in consecutive programme  
position.  
The Automatic Tuning operation can be cancelled at any time by pressing BACK button or  
MENU button.  
AUTO SEARCHING, PLEASE WAIT…  
55.25  
MHZ  
CH  
2
: EXIT  
: BACK  
After all receivable channels have been found and stored, the TV set will automatically return  
to programme position “1”.  
Note:  
POINT ◄► buttons or ENTER button: Start or Restart AUTO SEARCH.  
SEMI-AUTO SEARCH  
Use to preset a receivable channel in any desired programme position, e.g. the position with  
the same number as the channel.  
SEMI-AUTO SEARCH MENU  
Select channel “15”.  
SEMI-AUTO SEARCHING  
1
2
CHANNEL  
SEARCH  
15  
Enter into CHANNEL menu, press POINT ▲▼ buttons to select "SEMI-AUTO SEARCH".  
Press POINT ◄► buttons to enter into the SEMI-AUTO SEARCH menu.  
55.25 MHZ  
BACK  
:
:
:
SELECT  
ADJUST  
Press POINT ▲▼ buttons to select "SEARCH". Press POINT ◄► buttons to start the  
channel searching.  
3
Press POINT button and the tuning will go to the higher frequencies. Press POINT ◄  
button and the tuning will go to the lower frequencies. Use POINT button or POINT  
4
button to search for required TV station. Once a station is located, searching will  
automatically stop. Continue till desired channel is located.  
SEMI-AUTO SEARCH COMPLETED  
CHANNEL  
SEARCH  
15  
Press BACK button to return to the previous menu.  
Press MENU button to exit menu operation.  
55.25 MHZ  
BACK  
:
:
:
SELECT  
ADJUST  
MANUAL SEARCH  
Manual search a channel if it cannot be automatically tuned, such  
as when the signal is poor.  
MANUAL SEARCH MENU  
Select channel “15”.  
1
MANUAL SEARCH  
Enter into CHANNEL menu, press POINT ▲▼ buttons to select "MANUAL SEARCH".  
Press POINT ◄► buttons to enter into the MANUAL SEARCH menu.  
2
CHANNEL  
SEARCH  
15  
55.25 MHZ  
Press POINT ▲▼ buttons to select "SEARCH". Press POINT ◄► buttons to start the  
channel searching.  
3
:
:
:
SELECT  
:
BACK  
ADJUST ENTER STORE  
Press and hold POINT or POINT button to search for required TV station. Press  
ENTER button to save desirable station.  
4
Press BACK button to return to the previous menu.  
Press MENU button to exit menu operation.  
MANUAL SEARCH  
CHANNEL  
15  
SEARCH  
55.25 MHZ  
:
:
:
SELECT  
:
BACK  
ADJUST ENTER STORE  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION  
COLOUR SYSTEM  
The setting for colour system is only active in TV or AV mode. Usually, the colour system is set to  
the position of "AUTO". In case of abnormal colour, repeatedly press POINT ◄► buttons to select  
"AUTO", "PAL", "SECAM", "NTSC" or "NTSC4.43" until the best colour effect is reached.  
CHANNEL  
SOUND SYSTEM  
AUTO SEARCH  
The setting for sound system is only active in TV mode. Usually, the sound system is set to the  
position of "B/G". In case of abnormal sound, repeatedly press POINT ◄► buttons to select "D/K",  
"I", "M" or "B/G" until the best sound effect is reached.  
SEMI-AUTO SEARCH  
MANUAL SEARCH  
COLOUR SYSTEM  
AUTO  
SOUND SYSTEM  
SKIP  
B/G  
OFF  
SKIP  
CHANNEL SWAP  
This feature is used to remove unwanted channels from the channel scanning memory.  
You can skip the unused or undesired channels when you are  
selecting a channel using CHANNEL UP/DOWN (▲▼) buttons.  
This function is only active in TV mode.  
:
:
:
:
EXIT  
SELECT  
BACK  
ADJUST  
CHANNEL SWAP  
To swap the channels between two stored programme positions.  
Press MENU button to display the main menu.  
1
Enter into "CHANNEL" menu, press POINT ▲▼ buttons to select CHANNEL SWAP.  
2
CHANNEL  
CHANNEL SWAP  
Press POINT ◄► buttons or ENTER button to enter into the CHANNEL SWAP menu. Press  
3
CURRENT CHANNEL  
TARGET CHANNEL  
SWAPPING  
12  
16  
POINT ▲▼ buttons to select the CURRENT CHANNEL or TARGET CHANNEL, then press  
POINT ◄► buttons to select the swap channel. And then press POINT ▲▼ buttons to select  
SWAPPING item, then press POINT ◄► buttons or ENTER button to select "OK".  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
Note:  
:
:
:
:
EXIT  
SELECT  
BACK  
ADJUST  
When enter into CHANNEL SWAP menu again, TARGET CHANNEL will be turn to 0.  
PICTURE  
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select  
"PICTURE", and will display PICTURE menu.  
1
Press POINT ▲▼ buttons or ENTER button to enter into PICTURE menu.  
CHANNEL  
CHANNEL SWAP  
2
Press POINT ▲▼ buttons to select the item desired.  
CURRENT CHANNEL  
12  
3
TARGET CHANNEL  
SWAPPING  
16  
Press POINT ◄► buttons to adjust the item.  
OK  
4
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
PICTURE MODE: Used for selecting "STANDARD", "VIVID", "SOFT", "PERSONAL" or "DYNAMIC"  
.
CONTRAST: Used to decrease and increase contrast.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
BRIGHTNESS: Used to adjust darken and brighten image.  
PICTURE MENU (TV/AV/HDMI MODE)  
COLOUR: Used for lighten and darken colour. (Only in TV/AV/HDMI mode).  
TINT: Used to obtain proper colour.  
SHARPNESS: Used for soften and sharpen the image. (Only in TV/AV/HDMI mode).  
COLOUR TONE: Used for selecting colour temperature. Select "NORMAL", "WARM" or "COOL".  
PICTURE  
GAMMA: This function is used for adjusting the gamma value to obtain a better balance of  
contrast. Select "LOW", "MIDDLE", or "HIGH".(Only in TV/AV/HDMI mode).  
PICTURE MODE  
STANDARD  
CONTRAST  
BRIGHTNESS  
COLOUR  
COLOUR-R: Used to lighten and deepen red tone. (Only in PC mode).  
COLOUR-G: Used to lighten and deepen green tone. (Only in PC mode).  
COLOUR-B: Used to lighten and deepen blue tone. (Only in PC mode).  
TINT  
SHARPNESS  
COLOUR TONE  
GAMMA  
NORMAL  
LOW  
Note:  
"TINT" cannot be selected except for NTSC/ NTSC4.43 system.  
Only COLOUR TONE and GAMMA are available when SPORTS mode is ON.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
PICTURE MENU (PC MODE)  
PICTURE  
PICTURE MODE  
STANDARD  
NORMAL  
CONTRAST  
BRIGHTNESS  
COLOUR TONE  
COLOUR - R  
COLOUR - G  
COLOUR - B  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION  
SOUND  
SOUND  
SOUND  
SOUND  
SOUND MODE  
STANDARD  
EQUALIZER  
SOUND MODE  
EQUALIZER  
BALANCE  
STANDARD  
EQUALIZER  
BALANCE  
500 Hz  
1.5K Hz  
5K Hz  
BASS EXPANDER  
AUTO VOLUME  
BASS EXPANDER  
AUTO VOLUME  
OFF  
OFF  
OFF  
OFF  
10K Hz  
:
:
:
:
:
:
:
:
SELECT  
BACK  
EXIT  
SELECT  
BACK  
EXIT  
ADJUST  
ADJUST  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
SOUND MODE: Press POINT buttons to select  
"STANDARD", "NEWS", "MUSIC" or "PERSONAL".  
Press MENU button and the main menu will appear. Press POINT  
◄► buttons to select "SOUND", and will display SOUND menu.  
1
2
EQUALIZER: Select different frequency ranges of sound  
separately by pressing POINT ◄► buttons or ENTER button.  
Adjust values of "500 Hz", "1.5 K Hz", "5K Hz", "10K Hz" by pressing  
POINT ◄► buttons.  
Press POINT ▲▼ buttons or ENTER button to enter into SOUND  
menu.  
Press POINT ▲▼ buttons to select the item desired.  
3
4
BALANCE: Adjust the balance of the left and right channels.  
(-15~15).  
Press POINT ◄► buttons to enter the item selected.  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
BASS EXPANDER: Switch Bass Expander ON or OFF.  
AUTO VOLUME: Switch Auto Volume ON or OFF.  
Note:  
SOUND MODE, EQUALIZER and BASS EXPANDER is disabled when SPORTS mode is ON.  
TIMER  
Press MENU button and the main menu will appear. Press POINT ◄► buttons to  
select "TIMER", and will display TIMER menu.  
TIMER MENU  
1
Press POINT ▲▼ buttons or ENTER button to enter into TIMER menu.  
2
TIMER  
Press POINT ▲▼ buttons to select the item desired.  
3
OFF TIMER  
ON TIMER  
OFF  
12 : 30  
01  
Press POINT ◄► buttons to enter the item selected.  
4
ON TIMER CH  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
OFF TIMER: Once OFF TIMER has been set, when the set time is reached, the TV will  
shift to stand-by status. To select "OFF", "30 MIN", "60 MIN", "90 MIN" or "120 MIN"  
with POINT ◄► buttons or TIMER button. To cancel "OFF TIMER ", you can choose  
any option by the following ways.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
- Setting "OFF" in OFF TIMER menu.  
- Pressing POWER ON/OFF button on Side Control.  
- Pressing POWER ON/OFF button on Remote Control.  
ON TIMER: Once ON TIMER has been set, you won't miss any opportunity to watch the program you like. To set channel position, you can  
use NUMERIC buttons or DIGIT button. After ON TIMER has been set, ON TIMER INDICATOR will be light. To cancel "ON TIMER MODE", you  
can choose any option by the following ways.  
- Setting "- - : - -" in ON TIMER.  
- Disconnecting the AC power cord.  
ON TIMER CH: This function is only active that ON TIMER has been set. When the set time in ON TIMER is reach, the TV will turn on and  
enter the channel position you set directly. To set channel position, you can use NUMERIC buttons or DIGIT button.  
When OFF TIMER countdown time reach 1 minute, OFF TIMER OSD always showed for user information about power off time remain.  
OFF TIMER will be cancel when press any button during the countdown time dsplay.  
If ON TIMER didn't set, ON TIMER CH function will not actived.  
OFF TIMER and ON TIMER will be automatically cancelled during searching channels.  
The settings for OFF TIMER and ON TIMER will be automatically cancelled after the settings has been operated for one time.  
In case you left TV without any operation for 2 hours after power on by ON timer, TV will automatically power off itself.  
OSD  
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select "OSD"  
and will display OSD menu.  
,
1
OSD  
ENGLISH  
5 SEC  
LANGUAGE  
H - POSITION  
V - POSITION  
DURATION  
Press POINT ▲▼ buttons or ENTER button to enter into OSD menu.  
2
3
4
Press POINT ▲▼ buttons to select the item desired.  
INPUT LABEL  
Press POINT ◄► buttons to enter the item selected.  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION  
LANGUAGE: Press POINT ◄► buttons to choose ENGLISH, THAILAND, VIETNAM, or INDONESIA. For  
Middle East destination, it will be displayed: ENGLISH, ARABIC or PERSIAN.  
H-POSITION: OSD moves to the left side when POINT button is pressed. OSD moves to the right side  
OSD  
INPUT LABEL  
when POINT button is pressed. (0~100).  
OFF  
OFF  
OFF  
AV1  
V-POSITION: OSD moves up when POINT button is pressed. OSD moves down when POINT button  
is pressed. (0~100).  
AV2  
HDMI  
DURATION: Use this function to set the display time of the MENU when there is no operation on the TV.  
Press POINT button to decrease time, press POINTbutton to increase time. (5~60 seconds).  
INPUT LABEL: Use this function to give input source tag name follows input source device (ex: DVD player,  
Blu-Ray player, etc). Press POINT ◄► buttons or ENTER button to enter into INPUT LABEL menu. Press  
POINT ▲▼ buttons to select INPUT source, press POINT ◄► buttons to select "OFF"(blank), VCR, DVD,  
AUX, STB or GAME.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
Note:  
User can switch off or fill INPUT LABEL names with blank, by choosing "OFF" at INPUT LABEL menu option.  
SETUP  
INPUT MENU  
Press MENU button and the main menu will appear.  
Press POINT ◄► buttons to select "SETUP", and will display SETUP menu.  
1
INPUT  
Press POINT ▲▼ buttons or ENTER button to enter into SETUP menu.  
2
1. TV  
- VCR  
- GAME  
- DVD  
2. AV1  
3. AV2  
4. HDMI  
5. PC  
Press POINT ▲▼ buttons to select the item desired.  
3
4
Press POINT ◄► buttons to enter the item selected.  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
1~5  
: SELECT  
Note:  
BACK  
: EXIT  
"PC ADJUST" can not be selected except for PC mode.  
SETUP MENU  
CHILD LOCK: When CHILD LOCK is set "ON", the Side Control buttons will be locked except for  
POWER ON/OFF button. When Press the Side Control buttons, TV will display "LOCKED".  
ECO: This mode adjust panel backlight that can reduce the power consumption. Set it ECO "OFF",  
"LOW", or "HIGH".  
SETUP  
CHILD LOCK  
ECO  
ON  
OFF  
DYNAMIC AI: Automatically adjust video quality by video scene. Used to adjust contrast and color  
parameters until the display looks good. Set it ON or OFF.  
DYNAMIC AI  
ACTIVE CONTRAST  
PC ADJUST  
ON  
OFF  
ACTIVE CONTRAST: Used to improve poor contrast level quality from source signal in certain  
condition. Set it "OFF", "LOW, or "HIGH".  
SHOP MODE  
SHOP MODE: Press POINT ◄► buttons to choose HOME MODE or SHOP MODE. Press ENTER  
button to enter into HOME MODE or SHOP MODE.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
HOME MODE: In this mode, the adjustments you have set of "Picture mode" and "ECO" will be  
stored as the last memory automatically. The initial settings are "DYNAMIC" and "OFF".  
SHOP MODE: In this mode, 30 minutes later after you made some adjustments of "Picture mode" and "ECO" and no other operation on  
the LCD TV, the initial setting will be recalled. (The initial settings are "DYNAMIC" and "OFF".) The message of "INITIAL SETTING  
RECALLED FOR DEMO" will appear on the screen for 3 seconds.  
PLEASE SELECT AND PRESS ENTER BUTTON  
HOME MODE  
SHOP MODE  
INITIAL SETTING RECALLED FOR DEMO  
:
SELECT  
:
ENTER  
ENTER  
Note:  
When Active Contrast is select "HIGH" mode, the picture may be too darkness. In this case, select "OFF" or "LOW" mode.  
When in PC mode, "ACTIVE CONTRAST" can not be adjusted in the "SETUP" menu.  
Shop mode setting will be continued even after power off /on by Remote control, LCD TV or AC power plug.  
At the first power on and just after plug and play channel set-up, SHOP MODE menu will appear. Press POINT ◄► buttons to select and press  
ENTER button for SHOP MODE or HOME MODE. Then the pop up menu disappears.  
SETUP (PC MODE)  
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select "SETUP", and  
will display SETUP menu.  
SETUP MENU  
1
Press POINT ▲▼ buttons or ENTER button to enter into SETUP menu.  
2
3
Press POINT ▲▼ buttons to select the item desired.  
SETUP  
CHILD LOCK  
ECO  
ON  
OFF  
Press POINT ◄► buttons to enter the item selected.  
4
DYNAMIC AI  
ON  
ACTIVE CONTRAST  
PC ADJUST  
OFF  
Press BACK button to return to the previous menu.  
Press MENU button or wait for 5~60 seconds to exit menu operation.  
SHOP MODE  
Note:  
"PC ADJUST" is only active in PC mode.  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
PC ADJUST  
This function is used to adjust the position of image displayed on screen. It can be selected when the LCD TV could be received PC signal and in PC  
mode. Press POINT ◄► buttons or ENTER button to enter PC ADJUST menu. It can be select "AUTO ADJUST", "H-POSITION", "V-POSITION",  
"PHASE", "CLOCK" or "AUTO SHUT DOWN" to adjust.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DEALER MODE  
AUTO ADJUST: Press POINT ◄► buttons, and the TV automatically detects incoming signal, and  
adjust itself to optimize its performance. If the image is not displayed properly, a manual adjustment  
is required (Refer to following adjustments).  
SETUP  
CHILD LOCK  
ECO  
ON  
H-POSITION: The horizontal picture position will be moved to the left side by pressing POINT ◄  
OFF  
button. And it will be moved to the right side by pressing POINT button. (0~100).  
DYNAMIC AI  
ON  
ACTIVE CONTRAST  
PC ADJUST  
OFF  
V-POSITION: The vertical picture position will be moved down side by pressing POINT button.  
And it will be moved up side by pressing POINT button. (0~100).  
SHOP MODE  
PHASE: Eliminate disorder from the image. Press POINT ◄► buttons to adjust PHASE. (0~100).  
CLOCK: Eliminate flicker from the image. Press POINT ◄► buttons to adjust CLOCK. (0~100).  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
AUTO SHUT DOWN: Press POINT ◄► buttons to set AUTO SHUT DOWN ON or OFF. When  
PC is switched Off, ''NO SIGNAL'' appears for 30 seconds, TV will be automatically switched to  
Backlight off mode. During Backlight Off Mode within 10 minutes, TV will be switched to On Mode  
if PC is switched On. After Backlight Mode continues for 10 minutes, it will be switched to Standby  
Mode. During Standby mode, TV will not be switched to On mode even if PC is switched On. During  
Backlight Off mode, POWER indicator will become green.POWER ON/OFF button, NUMERIC (0-9)  
buttons and CHANNEL up/down buttons are enabled to switch On TV.  
SETUP  
PC ADJUST  
AUTO ADJUST  
H
V
-
-
POSITION  
POSITION  
DEALER MODE  
TO DISPLAY DEALER MODE:  
PHASE  
CLOCK  
Press INFO button on remote control while holding MENU button on Side control to display Dealer  
AUTO SHUT DOWN  
ON  
mode menu.  
The Dealer Mode has 9 different modes: VOLUME LOCK, TUNING LOCK, START MODE, OSD,  
RC, AC POWER MODE, START VOLUME LEVEL, MUSIC MODE SETUP and RESET.  
Take the way of setting VOLUME LOCK for example:  
:
:
:
:
SELECT  
BACK  
EXIT  
ADJUST  
Press POINT ◄► buttons to select a maximal volume.  
1
AUTO ADJUST  
Press INFO button on remote control while holding MENU button on Side control to display  
2
Dealer mode menu.  
VOLUME LOCK will be the default selection. (When you adjust others, press POINT ▲▼  
buttons to select the item desired.)  
REMOTE CONTROL  
3
Press POINT ◄► buttons to select "ON". (The maximal volume is the set value by step 1.)  
4
Press menu button to exit menu operation.  
5
INFO button  
VOLUME LOCK  
This function is used to limit the maximal volume.  
TUNING LOCK  
The way to prevent user from executing the Tuning function.  
POINT  
///►  
buttons  
START MODE  
The LCD TV will automatically enter to the setting mode while being turned on. You can select  
OFF, TV(0-10), AV1, AV2(DVD), HDMI or PC in START MODE. When it is set "OFF", it will  
keep the mode before being turning off.  
OSD  
When it is set "OFF", Corresponding OSD cannot display on the screen while operating.  
SIDE CONTROL  
RC  
You can set "ON" or "OFF" in RC MODE. Use this feature to set Remote Control Function  
including Power ON/OFF function.  
ON  
- Set Remote Control to normal function.  
OFF  
MENU button  
-
Set buttons on the Remote Control to prohibit to use include Power button.  
AC POWER MODE  
You can set "STAND", "LAST" or "ON" in AC POWER MODE.Use this feature to set TV  
condition when AC cord plug-in.  
STAND  
- When AC cord plug-in, LCD TV always STAND-BY.  
LAST  
DEALER MODE MENU  
- When AC cord plug-in, the LCD TV will depend on last TV condition. (ON or Stand-by)  
ON  
DEALER MODE  
- When AC cord plug-in, LCD TV always ON.  
VOLUME LOCK  
TUNING LOCK  
START MODE  
OFF  
OFF  
OFF  
ON  
START VOLUME LEVEL  
You can select "OFF" or "1-100" in START VOLUME LEVEL.  
Use this feature to set volume bar level position every time TV turned on.  
OSD  
ON  
STAND  
OFF  
RC  
Note:  
AC POWER MODE  
START VOLUME LEVEL  
MUSIC MODE SETUP  
RESET  
Even Start Volume Level set to higher value then Volume Lock, the Start  
Volume Level value automatically set to Volume Lock value.  
:
SELECT  
:
ADJUST  
:
EXIT  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DEALER MODE  
MUSIC MODE SETUP  
DEALER MODE  
MUSIC mode is used to block picture on channel program.Use this feature to set Music  
Mode condition in set 5 Position Channel.  
VOLUME LOCK  
TUNING LOCK  
START MODE  
OFF  
OFF  
OFF  
ON  
Press and hold Menu button on Side Controls, and press INFO button on remote control to  
display Dealer mode menu. Press POINT ▲▼ buttons to select MUSIC MODE SETUP.  
1
OSD  
ON  
STAND  
OFF  
RC  
Press POINT ◄► buttons or ENTER button to enter into MUSIC MODE SETUP menu.  
2
3
AC POWER MODE  
START VOLUME LEVEL  
MUSIC MODE SETUP  
RESET  
Press POINT ▲▼ buttons to select the item desired.  
Press POINT ◄► buttons to enter the item selected.  
4
:
SELECT  
:
ADJUST  
:
EXIT  
Press BACK button to return to the previous menu.  
Press MENU button or wait to exit menu operation.  
Note:  
MUSIC MODE SETUP  
When the channel set with Music mode is selected, Eco mode is ON.  
MUSIC MODE POS1  
MUSIC MODE POS2  
MUSIC MODE POS3  
1
255  
255  
255  
RESET  
This function returns all setting values to the factory default settings.  
MUSIC MODE POS4  
MUSIC MODE POS5  
255  
:
SELECT  
:
ADJUST  
BACK  
:
BACK  
: EXIT  
APPENDIX  
CLEANING LCD TV  
Be sure to disconnect the AC Power cord from AC outlet before cleaning the LCD TV.  
Clean your LCD TV as follows:  
Gently wipe the screen and cabinet with dry soft cloth.  
The screen is likely to be damaged if it is not maintained properly. Do not use hard objects  
like a hard cloth or paper. Do not use solvents or abrasions.  
CAUTION :  
Do not use benzene, thinner, or any volatile substances to clean the LCD TV. These  
chemicals may damage the cabinet finish.  
FUNCTION OF PRODUCT SAFETY FEATURE  
For protecting product safety, protection feature provided inside LCD TV. Refer to the  
following please.  
AUTO POWER OFF  
When a trouble is detected in the LCD TV, the protection function works and turn the LCD TV  
OFF automatically. When the LCD TV is turned OFF with this function, the POWER indicator  
becomes red and LCD TV's power cannot be turned ON.  
Disconnect Power cord and contact sales dealer where you purchased the LCD TV or the  
service center.  
To turn on LCD TV again for checking:  
1) Disconnect Power cord from AC outlet and plug it on again.  
2) Refer to "TURNING ON/OFF LCD TV" to attempt to turn on LCD TV.  
If LCD TV is not turned on, disconnect Power cord and contact to service center.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check the matters below once again.  
1. Make sure you have connected LCD TV to your equipment as described in the section "CONNECTING LCD TV".  
2. Check cable connection. Verify that all external equipment and power cords are properly connected.  
3. Verify that all power is switched on.  
4. If LCD TV still does not produce an image, re-start the external equipment.  
5. If the image still does not appear, unplug LCD TV from the external equipment and check the external  
equipment. The problem may be with your graphics controller rather than with LCD TV. (When you reconnect  
LCD TV, remember to turn the external equipment and TV off before you power up LCD TV. Power  
the equipment back on in order of : LCD TV and external equipment.)  
6. If the problem still exists, check the following chart.  
Problem:  
Try these Solutions  
Plug this LCD TV into the AC outlet.  
NO  
Press ON/STAND-BY button on SIDE Control or on Remote Control to open this LCD TV.  
Check POWER Indicator. If this indicator flashes, LCD TV has any trouble.  
POWER  
Check the batteries.  
Remote  
Control  
does not  
work  
Make sure nothing is between the Remote Receiver and the Remote Control.  
Make sure you are not too far from LCD TV when using Remote Control.  
Maximum operating range is 16.4' (5m).  
Is direct sunlight or strong artificial light shining on LCD TV's Infrared Remote  
Receiver? Eliminate the light by closing curtains, pointing the light in a different  
direction, etc.  
Check the connection between the external equipment and LCD TV.  
When turning LCD TV on, it takes a few seconds to display the image.  
Check the system that you select is corresponding with the external equipment or the video  
equipment.  
No image  
Make sure the temperature is not out of the Operating Temperature (0°C ~ 40°C).  
Turn off power, then turn on again, re-start LCD TV.  
Check Audio cable connection from Audio input source.  
Adjust the Audio source.  
No sound  
Press VOLUME (+) button.  
Press MUTE button.  
There are  
tiny black  
points  
and/or  
bright  
Dark or bright points of light (red, green, or blue) may appear on the screen. This is a  
characteristic of the LCD panels, not a malfunction of the LCD TV.  
point on  
the TV  
Abnormal  
colour of  
image  
Adjust the value of colour.  
Select different colour system.  
WARNING :  
High voltages are used to operate this LCD TV. Do not attempt to open the cabinet.  
If the problem still persists after following all operating instructions, contact the sales dealer where you  
purchased LCD TV or the service center. Give the model number and explain the difficulty. We will advise you  
how to obtain service.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Model  
LCE-24C100F(K)/(N)/(R)/(S)  
Maximum Visible Range  
Picture Resolution  
Voltage  
61cm (Screen Diagonal Size)  
1920(H) x 1080(V)  
AC110-240V 50/60Hz  
Power Consumption  
Power Management  
Colour System  
Sound System  
Channel Coverage  
LCE-24C100F(K)/(N)/(R)/(S): 44W  
VESA DPMS  
PAL/SECAM/NTSC/NTSC4.43  
D/K, I, M, B/G  
- VHF: E2-E12, R1-R12, K1-K9, J1-J12, A2-A13  
- UHF: 21-69, A14-A69, J13-J62  
- CATV: S1-S41, X, Y, Z, Z+1, Z+2  
75Ω  
Mains: 80mm x 20mm x 2pcs  
Maximum Output Power is 3W+3W  
Total Harmonic Distortion(THD)10%  
Aerial input impedance  
Speaker Size  
Sound speciality  
Input and Output terminals  
AV1 Input  
Video Input: Composite video Input (RCA Jack) x1  
Audio Input: L/R Stereo Input (RCA Jack) x 1 set  
Video Input: Component Y (combined with composite video input),  
CB, CR Input (RCA Jack) x1 set  
AV2 Input  
Audio: L/R Stereo Input (RCA Jack) x 1 set  
HDMI Terminal 19 pin x1  
Video Input: D-SUB 15 pin x1  
HDMI Input  
PC Input  
Audio Input: Mini stereo jack x 1  
Output Terminals  
Video Monitor Output: RCA jack x 1  
Audio Monitor Output: L/R Stereo Output (RCA jack) x 1 set  
Dimensions  
(Width x Height x Depth)  
LCE-24C100F(K)/(N)/(R)/(S): 580 x 396 x 156 mm (Including Stand)  
Net Weight  
g
(Including Stand )  
LCE-24C100F(K)/(N)/(R)/(S): 4.25 k  
Wall Mounting  
VESA Standard (200 x 200) wall hanging bracket.  
Operating Environment  
Operating Temperature  
Operating Humidity  
Storage Temperature  
Storage Humidity  
0ºC~40ºC 32ºF~104ºF  
20~80%  
-10ºC~50ºC 14ºF~122ºF  
20~80%  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
SIGNAL MODE COLUMN (Recommended)  
This LCD TV can correspond to the signals below. After connecting with the computer, LCD TV can automatically  
recognize the signal from the connected PC( computer)/ HDMI.  
PC SIGNAL MODE COLUMN (recommended)  
Note:  
In case LCD TV can not display properly due to the connecting cable or the graphic hardware, please make  
adjustments about phase, clock and so on.  
In principle, LCD TV can not display the signal mode which not described in the above column. But sometimes  
it can display a signal very similar with one of the signal described.  
If you want to change the definition and colour of PC, please select one from the column.  
It is not the trouble of LCD TV if interference appears on the picture while switching the signal mode.  
It is different from CRT Monitor that it is no blink of the picture when the V-Freq. of the signal s 60Hz. It is  
recommended to select 60Hz V-Freq. of your computer to display better pictures.  
The Dot Clock of the computer's signal must be less than 100 MHz.  
Specifications are subject to change without notice.  
In case of the following things, some messages will display on the screen.  
When the input signal from PC is out of the display range, "OUT OF RANGE" will display.  
When input signal is digital from DVD terminal, refer to the chart below.  
When input signal is digital from HDMI terminal, refer to the chart below.  
Frame  
NO.  
Resolution  
Frequency  
60.00HZ  
EIA1920×1080i@60  
EIA1920×1080p@60  
EIA1920×1080i@50  
EIA1920×1080p@50  
33.750  
67.500  
28.125  
60.00HZ  
50.00HZ  
56.250  
45.000  
37.500  
31.500  
31.250  
50.00HZ  
60.00HZ  
50.00HZ  
60.00HZ  
50.00HZ  
EIA1280×720p@60  
EIA1280×720p@50  
EIA720x480p(w)@60  
EIA720x576p(w)@50  
Audio Freq. Format :  
HDMITM(V.1.3 with Deep Color  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SANYO Electric Co., Ltd.  
Printed in Indonesia  
(
)
Part No: 1AA6P1P5969-- Z5YJ UE7-D  
Download from Www.Somanuals.com. All Manuals Search And Download.  

RCA CD Player RCU500 User Guide
RedMax Pole Saw PSZ2450S User Guide
Ricoh Printer SP C410DN User Guide
Ryobi Grinder BGH615 User Guide
Samsung Cell Phone 07212010 User Guide
Samsung Printer ML 4050ND User Guide
Samsung Vacuum Cleaner SR8845 User Guide
Sanyo Flat Panel Television LCD 27XA2 User Guide
Seagate Computer Drive ST980412AS User Guide
Senco Nail Gun SFN2 User Guide