Instruction Manual
AVL-209
HD (high-definition)*
LCD TV
* HD Cable or Satellite receiver required.
Before connecting, operating or adjusting this product, please read the manual completely.
Please keep this manual for future reference.
Call our HELPLINE 1-800-263-2244 for further assistance.
SANYO Canada Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Thank-you for choosing SANYO. This model has many features to enha nce your viewing, such as HDTV (via suitable
cable or satellite receiver) and computer monitor capability. Please read all instructions.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of
CAUTION
RISK OF ELECTRIC SHOCK
uninsulated dangerous voltage within the
product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION-To reduce the risk of electric shock, do
not perform any servicing other than that
contained in the operating instructions
unless you are qualified to do so.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
"Note to CATV system installer: This reminder is provided to call the CATV system installer's a ttention to Article 820-40 of
the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder and fluorescent lamp containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please
FCC STATEMENT
FCC Notice
LCD TV: A CLASS B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC CAUTION:
Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications to this monitor not expressly
approved by the manufacturer could cause harmful interference and would void the user's authority to operate
this device.
WARNING: This is a CLASS B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures to
counter interference.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
Electrical energy can perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest priority
on safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to
prevent potential danger, please observe the following instructions when installing, operating and cleaning
the product. To ensure your safety and prolong the service life of your LCD TV product, please read the
following precautions carefully before using the product.
5. Do not use this apparatus near water---for example, near a
bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool, and the like.
Do not use immediately after moving from a low temperature to high
temperature environment, as this causes condensation, which may
result in fire, electric shock, or other hazards.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
6. Clean only with dry cloth---Unplug this product from the wall
outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
7. Ventilation---Do not block any ventilation openings. Install in
accordance with the manufacturer instructions. The vents and other
openings in the cabinet are designed for ventilation. Do not cover or
block these vents and openings since insufficient ventilation can cause
overheating and/ or shorten the life of the product. Do not place the
product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings. This product is not designed for built-in
installation; do not place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
8.Heat sources---Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.Grounding or Polarization---Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Power cord protection---Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.Attachments---Only use attachments/ accessories specified by the manufacturer. Do not use attachments
not recommended by the manufacturer. Use of improper attachments can result in accidents.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions (continued)
12. Stand---Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer or sold with the apparatus. Do not place the product on an
unstable trolley, stand, tripod or table. Placing the product on an unstable base
can cause the product to fall, resulting in serious personal injuries as well as
damage to the product. When mounting the product on a wall, be sure to
follow the manufacturer’s instructions. Use only the mounting hardware
recommended by the manufacturer.
13. Move Carefully---When a cart is used, use caution when moving the
cart/ apparatus combination to avoid injury from tip-over. Sudden stops,
excessive force and uneven floor surfaces can cause the product to fall from the
trolley.
14. Lightning---Unplug this apparatus during lightning storms or when
unused for long periods of time.
For added protection for this television equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna. This will prevent damage to the
15. Servicing---Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way; for example, if the power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
16. Replacement parts---In case the product needs replacement parts, make sure that the service person
uses replacement parts specified by the manufacturer, or those with the same characteristics and performance
as the original parts. Use of unauthorized parts can result in fire, electric shock and/ or other danger.
17. Overloading---Do not overload wall outlets, extension cords, or convenience receptacles on other
equipment as this can result in a risk of fire or electric shock.
18. Entering of objects and liquids---Never insert an object into the product through vents or openings.
High voltage flows in the product, and inserting an object can cause electric shock and/ or short internal parts.
For the same reason, do not spill water or liquid on the product.
19. Damage requiring service---If any of the following conditions occur, unplug the power cord from the AC
outlet, and request a qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid is spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of
controls not described in the instructions can cause damage, which often requires extensive adjustment work
by a qualified technician.
e. If the product has been dropped or the cabinet has been damaged in any way.
f. When the product displays an abnormal condition or exhibits a distinct change in performance. Any
noticeable abnormality in the product indicates that the product needs servicing.
20. Safety checks---Upon completion of service or repair work, request the service technician to perform
safety checks to ensure that the product is in proper operating condition.
21. Wall or ceiling mounting---When mounting the product on a wall or ceiling, be sure to install the
product according to the method recommended by the manufacturer. This is a safety feature.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions (continued)
22. Power source---This product is intended to be supplied by a listed power supply indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power
company. For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will
prevent damage to the product due to lightning and power line surges. When the unit has to be used with
another power supply voltage, the power cable must be changed. Consult your product dealer. The socket
outlet should be installed near the equipment and easily accessible. Use only the power cord designated by our
dealer to ensure safety and EMC. When connecting other products such as VCRs and personal computers, you
should turn off the power of the unit for protection against electric shock.
23. Panel protection---The LCD panel used in this product is made of glass.
Therefore, it can break when the product is dropped or impacted upon by other
objects. Be careful not to be injured by broken glass pieces in case the LCD
panel breaks.
24. Pixel defect---The LCD panel is a very high technology product, giving you finely detailed pictures.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please
note that this does not affect the performance of your product.
<If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as
to provide some protection against voltage surges and built-up static charges. Section 810 of the National
Electrical Code provides information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
NEC—NATIONAL ELECTRICAL CODE
<An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can collide
with such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or
circuits, as contact with them might be fatal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Using the Remote Control
<Use the remote control by pointing it towards the remote sensor window of the
set. Objects between the remote control and sensor window may prevent
Note: This illustration is for reference only. The remote sensor may be in
different locations on different models.
3
0
0
3
5m
Cautions regarding use of remote control
<Do not expose the remote control to shock. In addition, do not expose the
remote control to liquids, and do not place in an area with high humidity.
<The remote control may not work properly if the remote sensor window of the main unit is under direct
sunlight or strong lighting. In such a case, change the angle of the lighting or LCD TV set, or operate the
remote control closer to the remote sensor window.
Batteries for the Remote Control
If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control.
Replace the battery cover.
3
Open the battery cover.
Insert two size-AAA batteries.
2
1
In s t a ll t w o "AAA"
batteries matching the
+ / - polarities of the
battery to the + / - marks
in sid e th e b a tte ry
compartment.
Precaution on battery use
Improper use of batteries can result in a leakage of chemicals and/ or explosion. Be sure to follow the
instructions below.
<Place batteries with their terminals corresponding to the (+ ) and (–) indications.
<Different types of batteries have different characteristics. Do not mix batteries of different types.
<Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/ or
cause old batteries to leak chemicals.
<Remove batteries as soon as they are non-operable. Chemicals that leak from batteries can cause a rash. If
chemical leakage is found, wipe with a cloth.
<The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
<If the remote control is not used for an extended period of time, remove the batteries from the remote
control.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation (continued)
Antenna Connection
CABLE TV (CATV) CONNECTION
A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75- ohm coaxial cable
to the set, screw the 75-ohm cable to the ANT. Terminal.
Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay channels are
scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company.
This converter/descrambler is necessary for normal viewing of the scrambled channels. For more specific instructions
on installing cable TV, consult your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable TV company is explained below. Please note: An RF switch provided with two inputs (A and B)
is required (not supplied).
RF switch (not supplied)
Two-set
signal
Cable TV Line
splitter
(not
supplied)
IN
OUT
Cable TV converter/
descrambler
(not supplied)
“A” position on the RF switch (not supplied) : You can view all unscrambled channels by using the TV’s channel keys.
“B” position on the RF switch (not supplied) : You can view the scrambled channels via the converter/ descrambler by
using the converter’s channel keys.
Note:
Consult your Dealer or Service Center for the type of splitter, RF switch or combiner that might be required.
ANTENNAS
The antenna requirements for good color television reception are more important than those for black & white
television reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna systems.
F-type connector
1. A 75-ohm system is generally a round cable with F-type connector that can
easily be attached to a terminal without tools (not supplied).
75-ohm coaxial cable (round)
2. A 300-ohm system is a flat “twin-lead” cable that can be attached to a 75-
ohm terminal through a 300-75-ohm adapter (not supplied).
300-ohm twin-lead cable (flat)
OUTDOOR ANTENNA CONNECTION
A. CombinationVHF/ UHF Antenna
300/ 75-ohm
adapter
(not supplied)
Use one of the following two diagrams if you connect an outdoor
antenna.
A: Using a VHF/ UHF combination outdoor antenna.
B: Using separate VHF and/ or UHF outdoor antennas.
VHF/ UHF
antenna
VHF/ UHF
antenna
or
300-ohm
twin-lead
75-ohm
coaxial cable
B. Separate VHFand/ or
UHF Antennas
UHF
antenna
VHF
antenna
300-ohm
twin-lead
Combiner
(not supplied)
300-ohm
twin-lead
OUT
IN
Antenna cable
or
75-ohm
coaxial cable
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls
Main Unit
CH+
CH-
Channel Up
Channel Down
Volume Up
VOL+
VOL-
Volume Down
MENU
MENU
SOURCE
Remote Sensor
Power Indicator
Select Input Signal
Power On/ Standby
1. SOURCE
To select the input signal source.
2. MENU
Press this button to access the MENU main page.
3. CH+/-
Press these two buttons to directly change the TV channel;
In OSD MENU, press these buttons to choose the OSD items.
4. VOL+/-
Press the VOL+ or VOL- button to directly increase or decrease the sound volume level;
In OSD MENU, press these buttons to adjust the value or setting of each item.
5. POWER
Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to
STANDBY.
Note:
Functions of VOL+/-, CH+/-, MENU, SOURCE and POWER are also provided to the remote control. This
operationmanualprovidesadescriptionbasedonoperatingfunctionswiththeremotecontrol.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls (continued)
Main Unit
1. D-Sub input/Audio Line in
Connect to the D-Sub/ audio output jacks on your PC.
2. Component Inputs (Y, Pb/ Cb, Pr/ Cr, Audio L, R)
Connect to the audio and component output jacks of a DVD player or Set-Top Box.
3. Antenna input
Allows you to connect cable or outdoor antenna.
4. S-Video input
Receive a S-Video signal from external source such as VCR or DVD player.
5. AV inputs (Video, Audio L, R)
Receive video/ audio signals from external sources such as VCR or DVD player.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls (continued)
Remote Control
To display channel status
or signal information
To select Stereo mode
Sound mute
Turn the unit on or off
[0-9] number buttons:
Direct channel select
To access the MENU main page
or exit menu operation
To quickly jump between current
channel and last selected channel.
To adjust volume;
To switch channels;
In MENU operation, use CH+/-
to select menu item
In MENU operation, use ENTER
or VOL+ / - to adjust selected
item
To confirm your operation
To set sleep timer
To select input signal source
Picture mode select
Audio mode select
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Cautions Before Connecting
Carefully check the terminals for position and type before making any connections.
The illustration of the external equipment may be different depending on your model.
Loose connectors can result in image or color problems. Make sure that all connectors are securely inserted into
their terminals.
Refer to the operating manual of the external device as well.
When connecting an external device, turn the power off on the panel to avoid any issues.
Connect a VCR
Rear of the VCR
AV IN
L
-
S VIDEO
ANT OUT
ANT IN
R
AUDIO
VIDEO
VCR
Y
W
R
Yellow (VIDEO)
White (AUDIO L)
Red (AUDIO R )
AV OUT
AUDIO
R
L
VIDEO
R
W
Y
S-Video
cable
Audio
cable
Video
cable
How to connect:
Connect the Audio/ Video cables between the Audio (L/ R)/ Video jacks on the unit and VCR.
Note:
For better video, you can use the S-video jack if your source supports it.
The unit automatically identifies S-Video if you are using S-Video jack. We recommend you to disconnect S-Video
cable before you use Video jack.
To play VCR
1. Turn on your LCD TV, press SOURCE
2. Turn on your VCR , insert a videotape and press the Play button.
button repeatedly to select Video.
Input Source
Video
Source-switch
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a Camcorder
OUT
IN
Y
W
R
Yellow (VIDEO)
White (AUDIO L)
Red (AUDIO R )
AUDIO
R
L
VIDEO
R
W
Y
Audio
cable
Video
cable
How to connect:
Connect the Audio/ Video cables between the Audio (L/R)/ Video jacks on the unit and camcorder.
To playback Camcorder
1. Turn on your LCD TV, press SOURCE
button repeatedly to select Video.
2. Turn on your camcorder and set it to output mode. (For details, refer to your camcorder owner's manual.)
3. Insert the tape into the camcorder and press Play button.
Input Source
Note:
Video
The operations of the camcorder may be different and is dependent on your
model. Please read the owner's manual of your camcorder to confirm
Source-switch
operation.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a DVD player
G
R
W
R
B
COMPONENT
Pb
AUDIO
AUDIO
Y
P
L
R
Y
Yellow (VIDEO)
R Red (AUDIO R, P / C )
r r
AV OUT
L
-
S
VIDEO
AUDIO
R
VIDEO
G Green (Y)
B
Blue (P / C )
b
b
Rear of the DVD player
or HD receiver
How to connect a DVD Player or HDTV Cable/Satellite receiver using Component
Video Connections:
Connect the Video cable between the Y, Pb, Pr input jacks on the unit and Y, Pb, Pr ( or Y, Cb, Cr) output jacks
on the DVD player or HDTV receiver.
Connect the Audio cable between the AUDIO input jack on the unit and AUDIO output jacks on the DVD
player. Set the DVD player/ HD receiver screen menu to 16:9 widescreen.
To play DVD/HDTV Receiver
1. Turn on your LCD TV, press SOURCE
2. Turn on your DVD player or HD receiver.
3. Insert a disc and press PLAY button, or select a channel on the HD receiver.
button repeatedly to select YPbPr.
Input Source
YPbPr
Source-switch
Note: There may be some movies or programs that are formatted in “super wide-
screen”, where a bit of the top and bottom portions of the TV screen might not be
filled.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a PC
How to connect:
Connect a D-Sub cable between the D-Sub jack on the PC and the D-Sub input jack on the unit.
Connect an Audio cable between the AUDIO output on the PC and AUDIO input jack on the unit.
To Watch the PC screen
1. Turn on your LCD TV, press SOURCE
button repeatedly to select D-Sub.
Input Source
D-Sub
2. Turn on your PC and check for PC system requirements.
3. Adjust the screen resolution and settings on your computer to the required
settings for this model: 1280 x 768 resolution with 60 Hz vertical scanning
frequency (or refresh rate).
Source-switch
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Unit On and Off
Turning the Unit On and Off
Turning On
Insert the power cord into the wall outlet.
Press the Power button on the remote control.
The unit will be turned on and you will be ready to use its features.
Turning Off
With the power on, press the Power button on the remote control
to turn off.
Note:
Youcanalsousethe Power buttononthecontrolpanelonthemainunit.
Viewing the MENUs and Displays
Your LCD TV has a simple, easy-to-use menu system that appears on the screen. This system makes it convenient
and fast to use features on the unit. The unit also lets you display the status of many of your LCD TV features.
Viewing the MENUs
Picture
With the power on, press the MENU button on the remote
control. The main menu appears on the screen. The picture
menu is selected.
1
Picture Mode
Brightness
Contrast
Color
Normal
50
75
60
50
12
Tint
Sharpness
Use the CH+/- to select submenu page. Use ENTER or
VOL+/- to access the selected submenu page.
2
3
Move
Select
Menu to exit
Use the CH+/- to select menu item. Use VOL+/- to adjust value of
item. Use ENTER or VOL+/- to confirm.
You can press the MENU button repeatedly to return or exit the menu
operations.
Note:
• To clearly introduce the menu operations, this operation manual
provides a description based on operation with the remote control.
• When performing confirmation in MENU operation, you may press
either ENTER or VOL+/- button.
Displaying Status Information
Press the DSP button on the remote; the unit will display current status information such as channel number, audio
mode or signal source, etc.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorizing the Channels
Your LCD TV can memorize and store all the available channels for both antenna and cable channels. After the
available channels are memorized, use CH+ / - to scan the channels.
Selecting the Signal Source
Before your LCD TV can memorize the available channels, you must specify the type of signal source that is
connected to the unit. (i.e., an antenna or cable system)
Channel
Press MENUto display the menu main page.
1
2
Auto Searching
Source
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
On
Press CH+/- repeatedly to select Channel page.
Frequency
55.25 MHz
Move
Select
Menu to exit
Press ENTER or VOL+/- to access the submenu.
Press CH+/- to select Source item.
3
4
5
Channel
Auto Searching
Source
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
Press ENTER or VOL+/- to toggle between Antenna or Cable.
On
Frequency
55.25 MHz
If you are connected to an antenna, please select Antenna. If you
connect cable, please select Cable.
Move
Select
Menu to exit
Storing Channels in Memory Automatically
Channel
Auto Searching
Source
Repeat steps 1~ 3 in [Selecting the Signal Source] to access Channelpage.
1
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
The Auto Searching item will be highlighted automatically.
On
Frequency
55.25 MHz
Press ENTER or VOL+/- to store channels in memory automatically.
2
Move
Select
Menu to exit
The unit will begin memorizing all the available channels. During the process
of the Auto Search, you can press Menu to exit.
Auto Searching
Menu to exit
CH No 11
Setting Auto Frequency Control (AFC)
Channel
Repeat steps 1~ 3 in [Selecting the Signal Source] to access Channelpage.
1
Auto Searching
Source
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
On
Press CH+/- repeatedly to select AFC item.
2
Frequency
55.25 MHz
Press ENTER or VOL+/- to select On or Off.
When the AFC is set to On, the unit will automatically tune the program
frequency to provide the best possible picture and sound.
Move
Select
Menu to exit
3
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorizing the Channels (continued)
Manual Fine Tuning
Channel
Auto Searching
Repeat steps 1~ 3 in [SelectingtheSignalSource] to access Channel page.
1
2
3
Source
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
On
Press CH+/- repeatedly to select Fine Tune item.
Frequency
55.25 MHz
Press VOL+/- to fine tune till the best possible picture and sound are
obtained.
Move
Select
Menu to exit
If you fine tune a program manually, the AFCwill be turned off automatically.
Adding and Erasing Channels
Channel
Use numberbuttonsto directly select a channel that will be added or erased.
1
Auto Searching
Source
Cable
On
Channel Skip
Fine Tune
AFC
Off
Off
Repeat steps 1~ 3 in [Selecting the Signal Source] to access Channelpage.
2
On
Frequency
55.25 MHz
Press CH+/- repeatedly to select Channel Skip item.
3
Move
Select
Menu to exit
Press ENTERor VOL+/- to select Onor Off.
4
When the item is set to on, the selected channel will be era sed.
When the item is set to off, the selected channel will be added.
The erased channels can not be selected by using the CH+/- buttons unless you use number buttons to
input channel number directly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Changing Channels
Using the Channel Buttons (CH+ or CH-)
Press the CH+orCH- to change channels.
When you press the CH+ or CH-, the unit changes channels in sequence. You will see all the channels that the unit
has memorized.
You will not see channels that were erased.
Direct Accessing Channels
Press the numberbuttonsto go directly to a channel.
To select a one-digit channel: press the 0-9 number buttons to input the channel number and press ENTER or
wait for some seconds to go to the selected channel.
To select a two-digit channel: press the 0-9 number buttons to input the channel number and press ENTER or
wait for some seconds to go to the selected channel.
To select a three-digit channel: press the 0-9 number buttons to input the channel number one by one, then the
unit goes to the selected channel.
Note:
When you use the number buttons, you can directly select channels that were erased.
Using the Return
button
Press this button to switch between the current cha nnel a nd the pre vious cha nne l.
Adjusting the Volume
Using the volume buttons (VOL+ and VOL-)
Press the VOL+or VOL- to increase or decrease the volume.
Using the MUTE button
At any time, you can temporarily cut off the sound using the MUTE button.
Press the MUTEbutton and the sound cuts off.
1
To resume sound, press the MUTEbutton again.
2
Selecting a MENU Language
Display
English
Press MENU to display the menu main
Language
1
Transparency
Back Light
Factory Reset
DCDi
Bright
Yes
On
Press CH+/- repeatedly to select Display page.
2
Off
Off
Captions
Off
CC When Mute
Press ENTER or VOL+/- to access the submenu.
3
Move
Select
Menu to exit
Press ENTER or VOL+/- to toggle between English, French and Spanish.
4
Press Menu to exit.
5
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Picture
Using the Preset Picture Mode
Picture
Press MENU to display the menu main
The picture page will be displayed automatically.
1
Picture Mode
Brightness
Contrast
Color
Normal
50
75
60
50
12
Press ENTER or VOL+/- to access the Picture submenu.
The PictureModeitem is highlighted automatically.
2
Tint
Sharpness
Press ENTERor VOL+/- to select a desired picture mode.
You may also use the P.Mbutton to quickly select picture mode.
3
Move
Select
Menu to exit
There are three preset picture modes (Bright, Soft and Normal) and one user-set picture mode (User). Each
preset mode has its own picture settings.
Bright: Select for a bright picture.
Soft: Select for a finely detailed picture.
Normal: Select for a normal picture.
Adjusted settings are stored in User mode.
When viewing regular (not HDTV) TV channels or sources via video/ S-Video, there will be a slight widening of
the image in order to fill the 16:9 screen.
Customizing the Picture
Picture
Picture Mode
Brightness
Contrast
Color
User
55
90
50
49
12
Pr e s s MENU to d is p la y th e m e n u m a in page.
The picture page will be displayed automatically.
1
Tint
Sharpness
Press ENTERor VOL+/-to access the Picturesubmenu.
Pre ss CH+/ - to se le ct the ite m you wish to cha nge .
Press VOL+/- to adjust the value of the item.
Press Menu to exit.
2
3
4
5
Move
Select
Menu to exit
In TV/Video mode
Option
Operation
Range
Function
Adjusts screen brightness for easier viewing of
darkpicturesuchasnightscenesandblackhair.
Brightness
VOL+ lighter
VOL- darker
0~ 100
VOL+ stronger
VOL- weaker
0~ 100
Adjusts image contrast.
Contrast
Color
Tint
VOL+ deeper
VOL- paler
Adjusts color saturation.
Adjusts tint for image.
0~ 100
0~ 100
VOL+ greenish
VOL- purplish
Sharpness
Adjusts image sharpness and displays a sharp
image.
0~ 24
VOL+ sharper
VOL- softer
In D-Sub mode
Option
Operation
Range
Function
Adjusts screen brightness for easier viewing of
darkpicturesuchasnightscenesandblackhair.
Brightness
VOL+ lighter
VOL- darker
0~ 100
VOL+ stronger
VOL- weaker
0~ 100
0~ 100
Adjusts image contrast.
Adjusts color saturation.
Contrast
Color
VOL+ deeper
VOL- paler
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Image in D-Sub (computer) mode
With working in D-Sub mode, this unit allows you to perform several adjustments for image
Adjusting the Picture Automatically
Image
Auto Adjustment
Image Position
Phase
Press MENUto display the menu main page.
1
30
Clock
1328
Press CH+/- repeatedly to select Image page.
2
Press ENTER or VOL+/- to access the Image page.
The Auto Adjustment item will be highlighted automatically.
3
Move
Select
Menu to exit
Auto Adjustment
Auto Adjustment: Yes
Press ENTER or VOL+/- again to access the Auto Adjustment page.
The Auto Adjustment / Yes item will be highlighted automatically.
4
Press ENTER or VOL+/- again to start Auto Adjustment.
5
The unit automatically adjusts phase, clock or position, etc.
Move
Select
Menu to exit
Adjusting Clock and Phase
Image
Auto Adjustment
Image Position
Phase
Repeat steps 1~ 3 in [Adjusting the Picture Automatically] to access Image page.
1
30
1328
Clock
Press CH+/- repeatedly to select Clock or Phase item.
2
Press VOL+/- to adjust the value of the item until the screen is well-aligned.
Move
Select
3
Menu to exit
Adjust the clock frequency of the set's interna l clock signa l. If shimmering or ra inbow-like noise is
a ppa rent in the ima ge, try a djusting the clock frequency setting.
You ma y find tha t ima ges blur, depending on the clock pha se of your PC's Processor. If you experience
blurring , you ca n obta in a clea rer ima ge by a djusting the pha se setting.
Note: Your computer settings should be 1280 x 768 resolution with 60Hz refresh ra te.
Adjusting the Image Position
The unit allows you to adjust the image position of the screen if it is not well-aligned.
Image Position
Repeat steps 1~ 3 in [Adjusting the Picture Automatically] to access Image page.
1
0
Press CH+/- to select Image Position item.
2
0
Press ENTER or VOL+/- to access the Image Position page.
3
Move
Select
Menu to exit
Press CH+/- or VOL+/- to adjust the image position until the screen is well-
aligned.
4
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Sound
Customizing the Sound
Sound
Press MENUto display the menu main page.
1
2
Bass
14
16
43
Treble
Balance
MTS
Press CH+/- repeatedly to select Sound page.
Mono
Press ENTER or VOL+/- to access the submenu.
3
Move
Select
Menu to exit
Press CH+/- to select Bass, Treble or Balance item.
4
Press VOL+/- to adjust the value of the item.
5
Option
Function
Operation
VO L+ stronger
Range
Adjusts Bass (low sounds)
0~ 31
0~ 31
Bass
VOL- weaker
VOL+ stronger
VOL- weaker
Adjusts Treble (high sounds).
Treble
VOL+ Higher volume from right speaker.
VOL-Higher volume from left speaker.
Adjusts volume balance (left and
right volumes).
Balance
0~ 100
Using the Preset Sound Mode
Use the S.Mbutton to quickly select Sound mode.
There are three preset Sound modes (News, Movie and Music ) and one user-set Sound mode (User). Each
preset mode has its own audio settings.
Movie: Select for a movie program.
Music: Select for a music program.
News: Select for a speech or conversation program.
Adjusted settings are stored in Usermode.
Setting Stereo Mode
This function is available in TV mode only.
Sound
Repeat steps 1~ 3 in [CustomizingtheSound] to access Soundpage.
Bass
14
16
43
1
2
3
Treble
Balance
MTS
Mono
Press CH+/- repeatedly to select MTS item.
Press ENTER or VOL+/- to select a proper stereo mode.
Move
Select
Menu to exit
You may also use the STEREO
button to quickly select a proper stereo mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Adjusting Menu Transparency
Display
English
Press MENUto display the menu main page.
Language
Transparency
Back light
1
2
3
Bright
Yes
Press CH+/- repeatedly to select Display page.
Factory Reset
DCDi
On
Off
Off
Off
Captions
Press ENTER or VOL+/- to access the submenu.
CC When Mute
Move
Select
Menu to exit
Press CH+/- to select Transparency item.
4
Press VOL+/- to adjust transparency.
5
Adjusting Back Light
Display
English
Language
Repeat steps 1~ 3 in [Adjusting Menu Transparency] to access Display page.
1
Transparency
Back Light
Factory Reset
DCDi
Bright
Yes
On
Off
Press CH+/- repeatedly to select Back Light item.
2
Off
Captions
Off
CC When Mute
Press ENTER or VOL+/- to adjust panel back light.
3
Move
Select
Menu to exit
Setting DCDi Function
Display
English
Language
Repeat steps 1~ 3 in [Adjusting Menu Transparency] to access Display page.
1
Transparency
Back Light
Bright
Yes
On
Factory Reset
DCDi
Off
Press CH+/- repeatedly to select DCDi item.
2
Off
Captions
Off
CC When Mute
Press ENTER or VOL+/- to select On or Off.
3
Move
Select
Menu to exit
You may set this function to On when viewing motion picture, which helps
to enhance picture quality by reducing sawtooth in the motion picture.
Loading Default Values
You may quickly load default values by using the Factory Resetitem.
Caution: Please be careful to use the Factory Reset item. Once you confirm to use this function, all your settings
will be reset and the unit loads default values.
Display
Repeat steps 1~ 3 in [Adjusting Menu Transparency] to access Display page.
1
Language
English
Transparency
Back Light
Factory Reset
DCDi
Bright
Yes
On
Press CH+/- repeatedly to select Factory Reset item.
2
3
Off
Off
Captions
Off
CC When Mute
Press ENTER or VOL+/- to load default values.
Move
Select
Menu to exit
Setting Sleep Timer
Press the SLP button repeatedly to set a sleep time to automatically turn off
the unit. Each press of the button, the value changes as below.
Off
30 min.
60 min.
90 min.
120 min.
Sleep Time: Off
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Closed Captions
The unit decodes and displays the closed captions that are broadcast with certain TV shows. These captions are usually
subtitles for the hearing impaired or foreign language translations. All VCRs record the closed caption signal from
television programs, so home-recorded video tapes also provide closed captions. Most prerecorded commercial video
tapes provide closed captions as well. Check for the closed caption symbol in your television schedule and on the tape’s
packaging:
.
Note:
The Caption feature does not work with YPbPr, D-Sub.
Not all programs and videos will offer closed captioning. Please look for the
symbol to ensure that captions will be shown.
Setting Closed Caption
Display
Language
English
Transparency
Press MENUto display the menu main page.
1
2
3
Back light
Factory Reset
DCDi
Bright
Yes
Press CH+/- repeatedly to select Display page.
On
Off
CC1
Off
Captions
CC When Mute
Press ENTER or VOL+/- to access the submenu.
Move
Select
Menu to exit
Press CH+/- repeatedly to select Captions item.
4
Press ENTER or VOL+/- to select a desired mode.
You may select between Off, CC1, CC2, CC3, CC4, T1, T2, T3 and T4.
5
The Closed Caption broadcasts can be viewed in two modes: CAPTION and TEXT. For each mode, four channels
are available.
The [CAPTION] mode shows subscripts of dialogues and commentaries of TV dramas and news programs while
allowing a clear view of the picture.
The [TEXT] mode displays various information over the picture (such as TV program schedule, weather forecast,
etc.) that is independent of the TV programs.
Setting CC When Mute
Display
Press MENUto display the menu main page.
Language
Transparency
Back light
English
1
2
3
4
5
Bright
Yes
Press CH+/- repeatedly to select Display page.
Factory Reset
DCDi
On
Off
CC1
Off
Captions
CC When Mute
Press ENTER or VOL+/- to access the submenu.
Move
Select
Menu to exit
Press CH+/- repeatedly to select CC When Mute item.
Press ENTER or VOL+/- to select On or Off.
If you set this item to On, the unit displays closed caption when you mute the sound.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Controls
Parental Controls
This function allows TV programs to be restricted and TV usage to be controlled based on FCC data. It prevents
children from watching violent or sexual scenes that may be harmful.
Restriction of TV programs includes two ratings that contain information about the program: the MPAA rating and the
TV Parental Guidelines. The MPAA rating is restricted by age. TV Parental Guidelines are restricted by age and content.
Since a TV program may use either the MPAA rating or the TV Guidelines, both should be adjusted for complete
control.
[1] Movie Rating (MPAA)
Rating
G
GENERAL AUDIENCES. All ages admitted.
PG
PARENTAL GUIDANCE SUGGESTED. Some material may not be suitable for children.
PARENTAL STRONGLY CAUTIONED. Some material may be inappropriate for children under 13.
RESTRICTED. Under 17 requires accompanying parent or adult guardian.
NO ONE 17 AND UNDER ADMITTED.
PG-13
R
age
based
NC-17
X
X Rating is an older rating that is unified with NC-17 but may be encoded in the data of older movies
Note:
The Movie rating is only age-based.
Example 1:
Movie Rating
Movie Rating: NA
“PG-13” in the age based rating is blocked, this will automatically block the
higher ratings “R”, “NC-17”, “X” also.
G
PG
PG-13
R
NC-17
X
Move
Select
Menu to exit
Example 2:
Movie Rating
“R” in the age based rating is blocked, this will automatically block
the higher rating “NC-17”, “X” also.
Movie Rating: NA
G
PG
PG-13
R
NC-17
X
Move
Select
Menu to exit
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Controls (continued)
[2] TV Rating
Rating
content based
D
L
S
V
FV
TV-Y (All children)
TV-Y7 (Direct to Older Children)
TV-G (General Audience)
age
based
TV-PG (Parental Guidance Suggested)
TV-14 (Parents Strongly Cautioned)
TV-MA (Mature Audience Only)
Content Rating can be set but this Rating is not D: Suggestive Dialog
normally broadcast by TV Station.
L: Foul Language
S: Sexual Content
V: Violence
Content Rating can be set.
FV: Fantasy Violence
Note:
Age-based ratingscan be modified bythe content-based ratingsbutonlyin the combinationsindicated byan in the table above.
Choosing lowerage-based rating blocksthe higherage-based ratingsregardlessofcontentratingssettings.
Example 1:
TV Rating
When TV-Y7 in the age-based rating is set to BLOCK, this will automatically
block the higher ratings: TV-G, TV-PG, TV-14 and TV-MA.
TV Rating: None
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Move
Select
Menu to exit
TV-Y7
F Violence
TV-Y7:
Example 2:
TV-PG
TV-PG: Violence
When TV-14 in the age-based rating is set to BLOCK, this will automatically
block the higher ratings: TV-MA.
In addition, if you block “L” sub-rating in TV-PG, then the TV-14 and TV-MA will
automatically be blocked.
Sexual Content
Foul Language
Suggestive Dialog
ALL
Move
Select
Menu to exit
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Controls (continued)
Accessing the Parental Controls Menu
Parental Controls
Enter Password
Press MENU to display the menu main page.
1
Press CH+/-to display Parental Controlspage.
2
Move
Select
Menu to exit
Press ENTER or VOL+/- to access the password checking page.
3
Parental Controls
Parental Lock
Clear All
On
Yes
None
NA
E
Off
Input the correct password with 0-9numberbuttons.
4
TV Rating
The default password is 1111, you may change the password yourself.
Movie Rating
CA-FR-Rating
CA-EN-Rating
Change Password
E
Press ENTER or VOL+/- to access the Parental Controlsmenu.
5
Move
Select
Menu to exit
Changing the Password
Change Password
From the Parental Controls menu, press CH+/- repeatedly to select
ChangePassworditem.
1
New Password
Re-Enter Password
Press ENTER or VOL+/- to confirm.
2
Input a new password and press ENTER or VOL+/- to confirm.
3
Move
Select
Menu to exit
Re-input the new password and press ENTERor VOL+/-to confirm.
4
Now the password is changed successfully.
Be sure to write down your password and retain it for future use.
Turn On or Off Parental Lock Control Function
Parental Controls
Parental Lock
Clear All
On
Yes
None
NA
E
Off
From the Parental Controls menu, press CH+/- repeatedly to select
ParentalLockitem.
1
TV Rating
Movie Rating
CA-FR-Rating
CA-EN-Rating
Change Password
Press VOL+/- to select On or Off.
If you want to validate Parental Lock Control settings, you need to set this item
2
E
to On.
Move
Select
Menu to exit
Clear Parental Control Settings
Parental Controls
Parental Lock
Clear All
On
Yes
None
NA
E
Off
From the Parental Controls menu, press CH+/- repeatedly to select Clear
Allitem.
1
TV Rating
Movie Rating
CA-FR-Rating
CA-EN-Rating
Change Password
Press ENTERor VOL+/-to clear all your parental control settings.
2
E
Caution: Please be careful to use this function. Once you confirm to use this
Move
Select
Menu to exit
function, all your settings will be cleared.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Controls (continued)
Adjusting the Movie Rating
Parental Controls
Parental
On
Yes
None
NA
E
Off
Repeat steps 1~ 5 in [Accessing the Parental Controls Menu].
1
Clear All
TV Rating
Movie Rating
CA-FR-Rating
CA-EN-Rating
Change Password
Press CH+/- to select MovieRating item.
2
E
Press ENTER or VOL+/- to display MovieRatingpage.
3
Move
Select
Menu to exit
Movie Rating
Press CH+/- to select a movie rating to be set.
4
Movie Rating: NA
G
PG
Press ENTER or VOL+/- to confirm blocking and MENUto return.
5
PG-13
R
When “PG-13” in the age-based rating is blocked, this will automatically
block the higher ratings “R”, “NC-17”, “X” also.
NC-17
X
Move
Select
Menu to exit
Adjusting the TV Rating
Parental Controls
Repeat steps 1~ 5 in [Accessing the Parental Controls Menu].
Parental
On
Off
1
Clear All
Yes
None
NA
TV Rating
Movie Rating
Press CH+/- to select TVRating item.
CA-FR-Rating
2
E
E
CA-EN-Rating
Change Password
Press ENTERor VOL+/- to display TVRatingpage.
3
Move
Select
Menu to exit
TV Rating
Press CH+/-to select an age rating to be set.
4
TV Rating: None
TV-Y
TV-Y7
Press ENTER or VOL+/-to confirm blocking.
5
TV-G
When TV-Y in the age-based rating is set to BLOCK, this will automatically
block the higher ratings: TV-Y7, TV-G, TV-PG, TV-14 and TV-MA.
For those ratings with content sub-rating, the sub-rating page appears on for
your further setting, for example, TV-PG.
TV-PG
TV-14
TV-MA
Move
Select
Menu to exit
Press CH+/-to select a content rating to be set.
6
TV Rating
TV Rating: None
TV-Y
Press ENTER or VOL+/- to confirm blocking.
When TV-PG in the age-based rating is set to BLOCK, this will automatically
block the higher ratings: TV-14 and TV-MA.
7
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Note:
Move
Select
Menu to exit
Since a TV program may use either the MPAA rating or the TV Guidelines,
both should be adjusted for complete control.
TV-PG
TV-PG: Violence
Sexual Content
Foul Language
Suggestive Dialog
ALL
Move
Select
Menu to exit
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Controls (continued)
Adjusting Canadian English Rating
CanEng Rating
CanEng Rating: E
From the Parental Controls menu, press CH+/- repeatedly to select CA-
EN-Ratingitem.
1
C
C8+
G
Press ENTER or VOL+/- to access the CanEngRatingpage.
PG
14+
18+
2
Press CH+/- to select a desired rating to be set.
3
Move
Select
Menu to exit
Press ENTER or VOL+/- to confirm blocking and MENUto return.
4
CANADIAN ENGLISH RATING CHART
Exempt - Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
E
C
Programming intended for children under age 8. No offensive language, nudity or sexual
Programming generally considered acceptable for children 8 years and over. No profanity,
nudity or sexual content.
C8+
G
General programming, suitable for all audiences.
PG
Parental Guidance suggested. Some material may not be suitable for children.
Programming contains themes or content which may not be suitable for viewers under the age of 14.
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens.
14+
18+
Intended for viewers 18 years and older and might contain depictions of violence.
Adjusting Canadian French Rating
CanFR Rating
CanFR Rating: E
From the Parental Controls menu, press CH+/- repeatedly to select CA-
FR-Ratingitem.
1
G
8 ans+
13 ans+
16 ans+
18 ans+
Press ENTER to access the CanFRRatingpage.
2
Press CH+/- to select a desired rating to be set.
3
Move
Select
Menu to exit
Press ENTER or VOL+/- to confirm blocking and MENUto return.
4
CANADIAN FRENCH RATING CHART
E
Exempt - Exempt programming.
General - Programming intended for audience of all ages. Contains no violence, or the
violence content is minimal or is depicted appropriately.
G
8+ General - Not recommended for young children. Programming intended for a broad
audience but contains light or occasional violence. Adult supervision recommended.
8 ANS+
Programming may not be suitable for children under the age of 13 - Contains either a few violent scenes
or one or more sufficiently violent scenes to affect them. Adult supervision strongly suggested.
Programming may not be suitable for children under the age of 16 - Contains frequent scenes
of violence or intense violence.
13 ANS+
16 ANS+
18 ANS+
Only for adult viewing.Could contain frequent violent scenes and extreme violence.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before ca lling for repa ir service, check the following items for possible remedies to the
encountered symptoms.
Symptoms
Check item
• This may be caused by obstruction to the antenna due to high rise
buildings or hills. Using a highly directional antenna may improve the
“Ghost” or double images
• Check that the AC power cord is plugged into the mains socket.
• Unplug the power cord, wait for 60 seconds. Then re-insert plug
into the mains socket and turn on the unit again.
No power
• Check antenna connections at the rear of the unit to see if it is
properly connected to the unit.
• Possible broadcast station trouble. Try another channel.
• Adjust the contrast and brightness settings.
• Check the Closed Captions control. Some TEXT modes could block
the screen.
No picture
• Select a correct input.
• Is a non-compatible signal being input?
Good picture but no sound
• Increase the VOLUME.
• Check that the unit is not muted.
Good sound but poor color
Poor picture
• Adjust the contrast, color and brightness
• Sometimes, poor picture quality occurs when having activated an S-VHS
camera or camcorder connection and having connected another peripheral
at the same time. In this case, switch off one of the other peripherals.
• Check whether the room is too bright.
• This may be caused by electrical interference (e.g. hairdryer, nearby
neon lights, etc.)
Horizontal dotted line
• Turn off the equipment.
• Check whether the batteries are working. Replace if necessary.
• Clean the remote control sensor lens on the unit.
• Do not use the remote control under strong or fluorescent lighting.
• The batteries should be inserted with polarity (+ , -) aligned.
Television not responding to
remote control
Snowy picture and noise
• Check the antenna connection.
No stable or not
synchronized D-Sub picture
• Check if you have selected the correct D-Sub mode in your PC.
No output from one
of the speakers
• Adjust Balance in the SOUND menu.
• Unplug the power cord, wait for some seconds. Then re-plug the
power cord and turn on the unit again.
Control buttons do not work
Do not use in hot or cold rooms (locations)
• When the unit is used in rooms (locations) with low temperature, the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight
or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
(Storage temperature: 0°C to + 50°C
Working temperature: 5°C to + 40°C )
Note:
If your problem is not solved, turn your unit off and then on aga in once.
Never attempt to repair a defective unit yourself.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
LCD Display panel information
Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.
The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel.
This background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible
LCD panel deterioration can be limited by observing the following steps:
A. Reduce the brightness/ contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
Note:
The marking or retained image on the LCD panel resulting from fixed image use is not an operating defect and as
such is not covered by Warranty. This product is not designed to display fixed image patterns for extended periods
of time.
Cleaning and Maintenance
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soap and water solution or a weak detergent solution.
• Use eyeglass cleaner to remove stubborn dirt from the LCD.
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using a chemically treated cloth, read the instructions that came with the cloth carefully.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply:
AC 100-240V 50/60Hz
Power Consumption:
Dimensions:
70W
22.4 (W) x 6.4 (D) x 17.1(H) (inch)
Weight:
19.8 lb
Screen:
20”
Computer settings:
TV system & channel coverage:
1280 x 768 with 60 Hz refresh rate
SYSTEM
NTSC-M
VHF
2-13
UHF
CATV
1-125
14-69
TV system:
Speaker:
NTSC-M
8W, 8W x 2
Accessories:
Operating manual X 1
Note: Design and specification are subject to change without notice.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYOCOMFORTWARRANTY
WARRANTY APPLICATION
New, unused Sanyo Color Television products purchased in Canada through a Sanyo authorized dealer are
warranted against manufacturing defects in materials and workmanship for ONE YEAR for parts and labor, from
the date of purchase by the original retail purchaser for non-commercial use. This warranty only applies in favor of
theoriginalretailpurchaserofthewarrantedproduct.
SANYOCANADAINC.'SRESPONSIBILITY
During the warranty period, SANYO Canada Inc. will repair, or at our option, replace a Color Television product
whichshowsevidenceofamanufacturingdefectinmaterialsorworkmanship.
ReplacementPARTSarewarrantedfortheremainingportionofthewarrantyperiod.
WHATISNOTCOVERED
(a)
(b)
(c)
(d)
(e)
(f)
ColorTelevisionproductspurchasedoutsideCanada.
ColorTelevisionproductspurchasedinausedcondition.
Problemsduetoproductset-upandinstallation.
AdjustmentsthatareoutlinedintheOperatingManual.
Accessoryitemsincludingantenna, batteriesandconnectingcables.
Damageinorduetotransportation.
(g)
(h)
Damageduetoimpropermaintenance, accident, abuse, misuseornegligence.
Damagecausedbylightningandpowersurges.
ORIGINALRETAILPURCHASER'SRESPONSIBILITY
You, the original retail purchaser, must present your original, dated bill-of-sale together with this warranty to
SANYOCanadaInc. ortoanauthorizedSanyoServiceDepot*whenyoumakeaclaimunderthiswarranty.
You, the original retail purchaser, are responsible for any costs of TRANSPORTING the product to and from
SANYO Canada Inc. or an authorized Sanyo Service Depot. You also are responsible for the cost of any
MAINTENANCEnecessaryinrespectoftheproduct.
*In-home service is only available to the units whose screen size is 25 inches or over, and limited to the locations
withina30-kmradiusofanyauthorizedSanyoServiceDepot, throughoutCanada.
WARRANTY BECOMES VOID This warranty becomes void if the product's serial numbers are altered or
removed or if any repair to the product is made other than by SANYO Canada Inc. or by an authorized Sanyo
ServiceDepot.
LIMITATIONS
(a)
SANYO Canada Inc. reserves the right to changeor improve the design of the model of the product
warranted hereunderwithout incurring any obligation to make any modifications to orto install any
improvementin oron the product.
In no eventshall SANYOCanada Inc. or any of its Authorized Dealers be liable forspecial or
consequential damage arising fromthe useof this product.
(b)
STATUTORY WARRANTIES
The above provisions do not preclude the operation of any applicable provincial statute which in certain
circumstances may not allow some of the limitations and exclusions described in this Warranty. Where any terms
of this Warranty are prohibited by such a statute, they shall be deemed null and void but the remainder of this
warrantyshallremainineffect.
HOWTOOBTAINWARRANTYSERVICE
Please contacttheSanyoAuthorizedDealer from whom the product was purchased or contact us directly at:
SANYOCanadaInc.
300 ApplewoodCres.
Concord Ont. L4K5C7
(905) 760-9944
1-800-263-2244
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED ON
RECYCLED PAPER
604-L20Y197-00
Ver 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|