INSTRUCTION MANUAL
VCB-3374
B/W CCD Camera
About this manual
•
Before installing and using the camera, please read this manual carefully. Be sure to
keep it handy for later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the conditions of use,
installation and environment, please be
sure to make the appropriate settings and
adjustments. If you need help with
installation and/or settings, please consult
your dealer.
FEATURES
• Built-in interline transfer method 1/3"
CCD, approx. 410,000 picture elements
• Low smear, anti-blooming, low lag, no
burning and no geometric distortion
using the CCD solid state image device.
• 100% solid state components giving
excellent immunity to shock and
vibration
• Not subject to interference from
magnetic or electrostatic fields
• High sensitivity, minimum required
illumination of 0,1 lux with F1.2 lens
• Horizontal resolution, more than 570 TV
lines
• New backlight compensation function
(Active when using an auto-iris lens)
• Externally adjustable flange back
(mechanical focus)
CONTENTS
INFORMATION TO USER ..................................2
PRECAUTIONS...................................................3
PARTS NAMES...................................................4
MOUNTING THE LENS......................................6
POWER SUPPLY.................................................8
CONNECTIONS..................................................9
SETTINGS.........................................................10
TROUBLESHOOTING.......................................12
SPECIFICATIONS .............................................13
• Low power consumption and quick start
• 24 V AC operation
(Commarcially available 24 V AC
adaptor)
ACCESSORIES
1 C mount adaptor (5 mm)................1 pc.
The C mount adaptor must be used to
be able to install a C mount lens on the
camera.
2 Lens iris plug (4-pin) ........................1 pc.
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
English
1
INFORMATION TO USER
This equipment has been tested and
Safety Guard
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules.
THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT
OPERATING AND
MAINTENANCE INSTRUCTIONS
IN THE LITERATURE
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause
harmful interference to radio
ACCOMPANYING THIS UNIT.
WARNING:
TO PREVENT THE RISK OF FIRE OR
ELECTRIC SHOCK , DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to
try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
For the customers in Canada
This Class B digital apparatus complies
with Canadian ICES-003.
Pour la clientèle canadienne
– Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
Cet appareil numerique de la Classe B
est conforme a la norme NMB-003 du
Canada.
– Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
This installation should be made by a
qualified service person and should
conform to all local codes.
Changes or modifications not expressly
approved by Sanyo may void the user’s
authority to operate this camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
English
PRECAUTIONS
In case of problem
Protect from high temperatures
Do not use the camera if smoke or a
strange odour comes from the unit, or if it
seems not to function correctly. Disconnect
the power cord immediately, and consult
your dealer (or a Sanyo Authorized Service
Centre).
Do not install close to stoves, or other heat
generating devices, such as spotlights, etc.,
or where it could be subject to direct
sunlight, as that could cause deformation,
discoloration or other damages.
Be careful when installing close to the
ceiling, in a kitchen or boiler room, as the
temperature may raise to high levels.
Do not open or modify
Do not open the cabinet, as it may be
dangerous and cause damage to the unit.
For internal settings and repairs, consult
your dealer (or a Sanyo Authorized Service
Centre).
Install where the temperature range will
stay between –10˚C and 50˚C.
(no condensation)
Cleaning
• Dirt can be removed from the cabinet
by wiping it with a soft cloth. To
remove stains, wipe with a soft cloth
moistened with a soft detergent
solution and wrung dry, then wipe dry
with dry soft cloth.
• Do not use benzine, thinner or other
chemical product on the cabinet, as that
may cause deformation and paint
peeling. Before using a chemical cloth,
make sure to read all accompanying
instructions. Make sure that no plastic
or rubber material comes in contact
with the cabinet for a long period of
time, as that may cause damage or
paint peeling.
Do not put objects inside the unit
Make sure that no metal objects or
flammable substance get inside the camera.
If used with a foreign object inside, it could
cause a fire, short-circuits or damages.
If water or a liquid gets inside the camera,
disconnect the power cord immediately,
and consult your dealer (or a Sanyo
Authorized Service Centre). Be careful to
protect the camera from rain, sea water,
etc.
Be careful when handling the unit
To prevent damages, do not drop the
camera or subject it to strong shock or
vibration.
Install away from electric or
magnetic fields
If installed close to a TV, radio transmitter,
magnet, electric motor, transformer, audio
speakers the magnetic field they generate
will distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not
install it where there is greasy smoke or
steam, where the dampness may get too
high, or where there is a lot of dust.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3
PARTS NAMES
Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor
with a VIDEO IN connector.
Line phase adjustment screw (LINE PHASE)
When using two cameras or more, the image on the
monitor may roll vertically when switching sources. This
rolling can be minimized by turning this screw.
24 V AC input terminal (24 V AC, GND)
External sync composite video signal input connector
(VS IN: BNC type)
Connect to this connector the synchronizing signal output
from a synchronizing signal device or the composite signal of
a video distributor.
Power indicator (POWER)
2
1
3
2
Comes on when the power to the camera is on.
Lens mount cap
1
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold
separately).
Camera installation bracket
The bracket can be fixed at the top or bottom of the
camera. When fixing the bracket, be sure to use the longer
screws and install the shorter screws on the opposite side to
seal the openings.
1 Shorter screws: M3 x 4
2 Longer screws: M3 x 6
3 Camera mounting
screw hole: 1/4"-20
UNC
CAUTION:
When installing the camera support, select a location
that can support the total weight of the camera and
accessories.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
English
PARTS NAMES
Lens iris output connector (4 pin)
This 4-pin connector is used to send the DC control signal
and power supply to an auto-iris type lens.
Camera setup section (under the cover)
1
2
3
4
This unit factory settings are as indicated below. These
settings are for when using a 1/3 inch CS mount DC
(without EE internal amplifier) type lens. However, if due to
installation conditions or environment the settings may need
to be modified for best results (see "SETTINGS"). To access
the controls, remove the cover fixing screw, then remove the
cover.
Control name
Position
OFF
Electronic iris (EI)/
Backlight compensation (BLC)
switch
a
c
VR401
L
E
V
E
L
Auto-iris lens switch
(A.I. LENS)
DC
EI
b
c
L
H
ON
OFF
ON
DC
VIDEO
BLC
A. I.
LENS
Lens iris level volume (LEVEL)
about centre
Note:
a b
• The EI/BLC switch is used for an auto-iris lens, therefore
the two settings cannot be used simultaneously.
• When using a 1/2 or 2/3 inch C mount VIDEO (with EE
internal amplifier) auto-iris type lens, set the A.I. LENS
switch to the VIDEO position.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5
Flange-back adjustment screw (FLANGE BACK ADJ.)
Flange-back lock screw (FLANGE BACK LOCK)
1
Flange-back adjustment
If the pick-up surface is not correctly positioned with relation
to the lens focal point, the picture will be out of focus (in
particular when using auto-iris power zoom lenses, sold
separately). If that is the case, adjust the flange-back position
as described below.
ADJ.
LOCK
2
1
3
1 Using a + screwdriver, loosen the FLANGE BACK LOCK
screw (M2:+).
Set the zoom lens to the maximum telephoto position,
set the focus using the focus ring on the lens.
2 Set the zoom lens to the maximum wide angle position,
set the focus using the FLANGE BACK ADJ. screw.
3 Repeat steps 2 and 3, until the image stays in focus when
changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE
BACK LOCK screw.
MOUNTING THE LENS
Check the lens mount
Do not use a lens if the length “L” is more than 7 mm.
That may damage the camera and prevent proper
installation.
L
Installation of a DC type auto-iris lens (sold
separately)
A 1/3 inch CS mount type lens without EE amplifier circuit
that only uses a DC power source. This camera can receive
(the A.I. LENS switch to the DC type) a CS mount type lens
without the need of an adaptor.
If the lens plug shape or wiring does not correspond, please
install the supplied plug as indicated in the pin layout table.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
English
MOUNTING THE LENS
Installation of a VIDEO type auto-iris lens
(sold separately)
A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit
that uses the video signal and a DC power source.
2 (A)
(B)
1 Remove the lens mount cap.
2 Attach the supplied C mount adaptor (A) to the
auto-iris lens (B), then install the assembly on the camera.
3 Connect the lens plug to the LENS connector on the side
3
of the camera.
1
2
3
If the lens plug shape or wiring does not correspond to
the specifications below, connect the supplied plug as
indicated.
• When using lenses from other makers, make sure that
the pins connections in the plug correspond to the
ones of the camera.
4
Refer to the lens specifications to check the pins
connections in the plug.
• If they are different than indicated, remove the original
plug and connect the supplied plug according to the
diagram.
4
4 Set the A.I. LENS switch in the camera setup section to
the VIDEO position.
DC
VIDEO
Pin layout
DC type lenses
Brake coil (–)
VIDEO type lenses
+12 V DC (50 mA max.)
Not used
1
2
3
Brake coil (+)
Drive coil (+)
Video output (1.0 Vp-p, high
impedance)
Drive coil (–)
Ground (for video signal and DC
power)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7
Compatible auto-iris lenses
1/3 inch Sanyo DC type lens
1/2 or 2/3 inch VIDEO type lens
Standard angle, f= 9 mm
VCL-CS8LY: Standard angle, f= 8 mm
VCL-CS4LY: Wide angle,
f= 4 mm
Telephoto angle, f= 12 mm
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm
More telephoto angle,
f= 16 mm
If using a VIDEO type auto-iris lens
• Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume
should be turned all the way to Av (Average).
• Depending on the type of lens used, the lens may not perform properly. In such a case,
adjust the LEVEL volume on the lens casing to correct.
POWER SUPPLY
With this camera use only the 24 V AC power adaptor
model No. VPT-115 available from Sanyo.
Power supply connections
Use a 3 wire grounded cable (22 AWG or more), and
connect as shown by the illustration.
GND
AC
AC
CAUTION:
• To prevent camera and/or AC adaptor failure, pay
close attention to polarity when making the
connections.
• To prevent fire hazard any UL listed wire rated VW-1,
should be used for the 24 V AC cable input terminal.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
English
CONNECTIONS
Basic connection for monitoring or recording
(A)
1
The peripheral devices (VCR, monitor, lens, etc.) and
cables are sold separately.
1 Make the video signal connection between the camera
and the monitor or time lapse VCR.
2
2 Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on
the monitor using the Brightness and Contrast controls.
Coaxial cable type and maximum length
• Cable type RG-59U, 100 m maximum.
• Cable type RG-39U, 200 m maximum.
CAUTION:
The RG-59U type cable should not be run through electrical
conduits or through the air.
(Video signal connections)
: VIDEO IN
: VIDEO OUT
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTINGS
VR401
L
E
V
E
L
EI
L
H
ON
OFF
ON
DC
VIDEO
BLC
A. I.
LENS
Electronic iris function setting
EI
Use a manual or fixed iris lens and set the lens aperture to the
shortest F stop. Set the EI/BLC switch to EI-ON position.
ON
OFF
ON
Note:
BLC
Please refer to the specifications for dynamic range of the electronic
iris.
CAUTION:
• The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set to the
EI-ON position, do not use an auto-iris lens.
• If used under fluorescent light, the image may flicker. In such a case, change to
incandescent lighting or set the EI/BLC switch to the OFF position and use an auto-iris
lens.
• When shooting bright subjects, pay attention to the light angle in order to avoid or
minimize the smear phenomenon effect.
When using an auto-iris lens (for indoor/outdoor use)
Set the EI/BLC switch to the OFF position.
CAUTION:
If conditions are outside the electronic iris operation range or more than the maximum
illumination, it will cause saturation of the CCD. In that case, use a manual iris lens.
Lens iris adjustment
If using a DC type auto-iris lens, you will need to set the LEVEL
(VR401) volume when shooting in the conditions described below.
L (counterclockwise): To decrease the contrast
VR401
L
E
V
E
L
H (clockwise): To increase the contrast
• If shooting simultaneously in a dark room and through a bright
L
H
window.
• If the subject background is extremely bright or dark.
• If the brightness of the picture on the monitor is not correct.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
English
SETTINGS
Backlight compensation setting
EI
Use an auto-iris lens and set the EI/BLC switch to the BLC-ON
position, to engage the backlight compensation function.
Use an auto-iris lens. Set the EI/BLC switch to BLC-ON switch to
the ON position.
ON
OFF
ON
BLC
If using a VIDEO type auto-iris lens
• The ALC volume on the lens should be turned all the way to Av (Average).
• If the backlight compensation function does not compensate properly for the conditions,
set using the LEVEL volume on the lens.
CAUTION:
The electronic iris function and the backlight compensation function cannot operate
simultaneously.
LINE PHASE ADJUSTMENT
When using a camera switcher to connect 2 cameras or more to
one monitor, there may be a vertical roll of the images when
switched. In such a case, set as described below.
Switch the display on the monitor from camera 1 to camera 2.
Adjust the LINE PHASE volume on camera 2 until the vertical roll
of the image stops.
If more than two cameras are used, please repeat this procedure
for all the cameras.
CAUTION:
If the vertical roll cannot be corrected by setting the LINE PHASE
volume on camera 2, try setting the LINE PHASE volume on
camera 1. If it still cannot be corrected, please check that the
polarity of the power cords of all connected devices is correct.
TROUBLESHOOTING
Before taking the camera for repairs, please check below to make sure that the camera is
used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo
Authorized Service Centre.
No picture on the monitor screen
• Is the power turned on to all connected devices? Is the voltage correct?
• Are all the signal connecting cables correctly connected?
• Is the lighting sufficient?
• Has the lens cap been removed?
• Is the lens type (DC or VIDEO) correctly selected?
Depending on the type of lens, the A. I. LENS switch must be set accordingly.
• Is the iris control correctly set?
A: When using a DC type lens, the LEVEL volume (inside the camera casing) should be
adjusted.
B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.
The picture is not clear
• Is the monitor correctly adjusted?
• Is the flange-back position correctly set?
• Is the lens focus correctly adjusted?
• Are the lens surfaces clean?
If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the
lens use a soft cloth or a commercially available lens cleaning set.
SERVICE
This camera is a precision instruments and if treated with care, will provide years of
satisfactory performance. However, in the event of a problem, the owner is advised not to
attempt to make repairs or open the cabinet. Servicing should always be referred to your
dealer or Sanyo Authorized Service Centre.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
English
SPECIFICATIONS
Scanning system : EIA standard (525 TV lines, 30 frames/sec.)
Interlace : PLL 2:1 interlace
Image device : 1/3 inch solid state image device CCD
Picture elements : 811 (H) x 508 (V)
Effective picture elements : 768 (H) x 494 (V)
Synchronizing system : Line lock/External sync (Automatic switching)
Resolution : 570 TV lines horizontally, 350 TV lines vertically
Video output level : 1.0 Vp-p/75 ohms, composite
Video S/N ratio : More than 50 dB
Minimum required illumination : Approx. 0.1 lux with a F 1.2 lens,
(incandescent lighting)
approx. 0.14 lux with a F 1.4 lens
Backlight compensation : Manual ON/OFF switching, zone light measuring system
(Active when using an auto-iris lens)
Electronic iris function : Manual ON/OFF switching
Electronic iris range : 0.1 lux to 26,000 (F 1.2, lens)
0.14 lux to 34,000 (F 1.4, lens)
Flange-back : 12.5 mm 0.8 mm
Gamma correction : = 0.45
Lens mount : CS mount (or C mount with the supplied adaptor)
Environmental conditions : Temperature: –10˚C ~ +50˚C
Humidity: less than 90% (no condensation)
Power supply : 24 V AC, (–4 to +4 V) 60 Hz
Power consumption : Approx. 3.1 W
Weight : Approx. 330 g (without lens)
Dimensions
56
108.5
99.5
1.5
VIDEO OUT
VS IN
POWER
45
SEE INSTRUCTION MANUAL
GND 24V AC
LINE
PHASE
CLASS2WIRING 24V AC
11
1/4”–20 UNC
28
12
22
Features and specifications are subject to change without prior notice or obligations.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
13
|