Congratulations on your purchase of the RF-QS2-T
Bluetooth Speakerphone. This speakerphone enables
comfortable, hands-free communication with a
Bluetooth-compatible phone.
Voice dialing
When no call is in progress, quickly press and release
Power/Send/End. When you hear a tone, speak the
number or voice tag for the number you want to call.
(The phone must have a voice dial feature and have
recorded voice tags.)
Package contents
• RF-QS2-T speakerphone • Car charger adapter
Making a call
• USB charging cable
• Quick Setup Guide
To...
Make a call
Redial
Answer a call
End a call
Refuse a call
Change the speaker
volume
Do this...
Features
Press Power/Send/End.
Double-press Power/Send/End.
Press Power/Send/End.
Press Power/Send/End.
Double-press Power/Send/End.
Press the volume up button (+) to increase
volume or press the volume down (-) button to
decrease.
Indicator
Volume down
Power/Send/End
button
Charger
connector
QS2-T Car Speakerphone
RF-QS2-T
Volume up
Visor clip
Microphone
Charging the battery
Mute or unmute a call Press and hold the Volume down (-) button until
a tone is heard.
Switch a call between Press and hold Power/Send/Endfor
the phone and the
speakerphone
Before using your speakerphone, you must charge it
for about two hours. When the battery is fully charged,
it provides up to 11 hours of talk time and up to
1,400 hours of standby time.
two seconds.
1
USB charging: use the USB cable to plug your QS2-T
speakerphone into a computer or other USB power
port.
Turning the indicator on or off
•
Press the power and volume up buttons at the same
time for about four seconds. The indicator turns on.
Press the power and volume down buttons at the
same time for about four seconds. The indicator
turns off. You can enable or disable the indicator
when the speakerphone is connected with your
phone.
2
Car charging: use the car charger adapter and USB
charging cable to charge your QS2-T speakerphone
in your car.
Turning the speakerphone on
Press and hold the Power/Send/End for about
two seconds. RF-QS2-T beeps and the yellow-green
indicator light starts blinking. (First time use requires
pressing it for 4 seconds.)
Disconnecting the speakerphone from the phone
To disconnect the speakerphone from the phone, do
one of the following:
Turning the speakerphone off
Press and hold the Power/Send/End for about
four seconds, RF-QS2-T beeps and the red indicator light
is displayed briefly.
•
•
•
Turn off the speakerphone.
Disconnect the RF-QS2-T in the phone’s menu.
Move the speakerphone more than 33 ft. (10 m)
away from the phone.
Note: You do not need to delete the pairing to
disconnect the speakerphone. When you reconnect a
paired speakerphone, you will not be asked for its PIN
again.
If you want to pair your speakerphone with new phones,
you don’t need to erase all paired device information.
There can be up to eight different paired devices
information stored.
Pairing the speakerphone
1
Make sure that the compatible phone is turned on
and within 33 ft. (10 m) of the speakerphone.
Turn on the QS2-T and make sure it’s fully charged.
Press and hold the Power/Send/End button for
about four seconds. The yellow-green indicator
flashes rapidly. Release the button. The
speakerphone is now in pairing mode.
Activate the Bluetooth connection from the phone.
See your phone’s documentation for more
information.
2
3
4
To erase paired devices from your speakerphone:
•
When the speakerphone turned off, press and hold
the Power/Send/End and volume up (+) buttons
simultaneously for more than six seconds. A tone
plays, and the indicator flashes red and yellow-green.
The speakerphone then enters the pairing state
automatically.
Set the phone to start searching for Bluetooth
devices.
5
6
Select RF-QS2 from the list.
Enter the PIN 0000 to connect (or“pair”) the
speakerphone to the phone. The speakerphone
beeps once, and the indicator blinks yellow-green to
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK SETUP GUIDE
indicate the Bluetooth connection is active.
|