Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Features
Control Locations
2
3
Choosing a Power Supply
Preliminary Settings
5
7
Tuning Modes
12
21
23
26
29
34
36
Clock Radio Operation
Special Tuning Techniques and Controls
Using Your Cassette Recorder
Special SSB/CW Reception Techniques
Care and Maintenance
Specifications
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Continuous Tuning allows continuous
reception of all stations and bands.
Band Select Buttons offer instant selec-
tion of any desired frequency bandwidth
on SW.
Fast response, Three Color LCD in-
dicates station frequency in large easy-
to-read numbers, including dual time,
memory location, signal strength and bat-
tery life.
Tuning Speed Select Switch permits
you to tune stations at either a fast or slow
speed.
Adjustable Sleep Timer allows you to
fall asleep to music or other programming
DirectAccess Keypad permits instant
tuning of any desired frequency from 87.5
to 108MHz on the FM band and from 150
to 29,999 KHz on the AM band.
Standby Mode turns on the radio
automatically at a pre-set time either by
buzzer or radio program.
Fifty-Four Memory Pre-sets offer ins-
tant access to your favorite stations on
LW,MW, FM and SW.
Stereo Headphone Jack permits recep-
tion of FM multiplex stereo broad-casts.
Folding Stand alows you to position the
radio either vertically or at an angle while
maintaining stability.
AC/DC Power Supplies for use
virtually anywhere in the world.
Special Tuning Controls further im-
proves radio reception.
BFO Control (beat Frequency Oscillator)
allows reception of SSB (Single Side
Band) and CW(Continuous Wave Morse
Code) transmisisons.
Dual Time Setting allows you to pre-set
your local time and UTC World Time, or
any two time zones with instant recall.
Standby Recording function provides
recording at pre-programmed time.
Scanning Circuit permits you to check
various frequencies on a certain band-
width and lock on to it at random.
Sensitive Built-in Microphone provides
recording anywhere without an extra
microphone.
Cancel Button allows you to instantly
change incorrect information keyed into
the microprocessor.
FullyAuto Stop on tape playing, fast-
forwarding and rewinding.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL LOCATIONS
1.Display Light Button
2.Radio Power on/off Button.
3.Sleep Timer.
4.Time Set.
5.Dual Time Set
24.Tape Playing LED Indicator
25.Cassette Tape Compartment
26.Tape Recording Button
27.Tape Playing Button
28.Tape Rewinding Button
29.Tape Fast Forward Button
30.Stop/Eject Button.
6.Manual Tuning/Auto Scan Button
7.Band Selector.
8.Frequency Select Button.
9.Standby Button.
31.Pause Button
32.Telescopic A n t e n n a
33.Carrying Handle
34.Rotary Tuning Knob.
35.Tuning Speed Control
36.Lock Switch
10.BFO on/off Selector
11.FM Stereo/Mono Mode Selector.
AM Wide/Narrow Mode Selector.
12.Alarm By Radio/Buzzer Selector.
13.BFO Pitch
37.Volume Control
14.RF Gain Control
15.Tone Control
16.Cancel Button
38.CrO2/Normal/Tape Select Switch
39.Timer Recording on/off Switch
40.Beat Cut Switch
17.Enter Command Button
18.Memory Entry Button
19.Numeric & Bandwidth Button
20.Meter Select Button
21.Built-in Microphone
22.LCD Display
41.AM External A n t e n n a jack
42.Stereo Headphone Jack.
43DC Input Jack/6 volts
44.Folding Stand
45.Battery Compartment.
23.Tape Recording LED Indicator
25
24
23
22
1
2
3
4
5
6
7
9
11
10
12
8
20
13
21
18 19 17 16 15
14
3
Download from Www.Somanuals.com. All Manuals Search And Download.
31
30 29 28 27 26
32
44
45
33
34
38
39
40
35
36
41
42
43
37
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING A POWER SUPPLY
You can operate the receiver using:
4 Alkaline “D”size Batteries
HouseholdAC[With optional AC Adaptor]
12 Volt DC Automobile Battery [With
optional DC adaptor]
2.Insert 3 "AA" batteries in the "Back-up"
compartment and 4 "D" size batteries in
the "Radio" compartment. Be sure to
position them as illustrated on the back
of the radio, and on top of the "lift-out"
ribbons for easy removal.
3.Replace the battery compartment cover
and press down until you hear it snap
closed.
USING BATTERIES
1.Press latch marked“OPEN”on battery
compartment cover in the direction of the
arrow and lift off cover.
NOTE
Whenever the radio is turned off, the battery
indicator will flash for about five seconds to
show battery condition.
When the "MAIN' batteries become ex-
hausted, the micro-processor will automa-
tically be powered by the "BACK-UP"
batteries.
If the indicator falls below #2, the 4MAIN
"D" size batteries should be replaced.
When the display on the micro-processor
begins to fade, replace the 3 "AA" batteries
in the "BACK-UP" circuit. During battery
replacement make sure the Lock Switch (26)
is in the locked position (
). This will
prevent any memory presets from being lost
during the battery replacement. Battery
replacement should be completed within 2
minutes.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USING HOUSE CURRENT [AC]
The receiver may be powered by AC current
using the AC adaptor (not included).Insert
the small barrel shaped plug into the jack on
the side of the radio marked "DC IN 6V" .
Plug the other end of the adaptor into a
standard household outlet.Whenever AC
is used, the batteries are automatically
disconnected.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PRELIMINARY SETTINGS
SETTING THE CLOCK
The time is displayed in the 24 hour mode
since most shortwave stations operate
according to UTC. This is the standard that
is used throughout the world.
The clock will start when 3 AA size
batteries are installed. The display shows
0:00
1.Press "TIME SET" . "0:00" . disappears
& for 12 seconds TIME SET flashes.
2.While FLASHING set the correct time
by pressing the numbered buttons. As
you press the corresponding button the
number shows up on the LCD display.
3.If you press the wrong number, press the
" C" [CANCEL] button which deletes
one number at a time. Repeat step #2
again.
NOTE
Time can only be adjusted when TIME
SET is in flashing mode.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4 . N o w p r e s s b u t t o n m a r k e d " E N T E R " .
D i s p l a y s h o w s h o u r s a n d m i n u t e s .
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING DUALTIME
A second time zone can be programmed
into this unit such as your home time
if you are travelling, or UTC World Time for
instant access to short-wave broadcasts or
the local time where ever you may be.
1.Press right side "DUAL TIME" button
then the display will show the secondary
TIME and
appears.
2.Press "TIME SET" button. Clock time
will disappear & "TIME SET" will flash
for 12 seconds.
3.While "FLASHING" set the correct time
by pressing the numbered buttons.As
you press the corresponding button the
number shows up on the LCD display.
4.If you press the wrong number, press the
"C" [CANCEL] button which deletes one
number at a time. Repeat step # 3 again.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Now press button marked "ENTER" ,
Display shows hours and minutes.
6.By pressing the right side "DUAL TIME"
button now, the LCD display will once
again show the clock time.
7.To verify "DUAL TIME" , press the left
side 'DUAL TIME" button to display your
"OTHER" time zone. When you release
the button the clock will show your current
local time.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BAND SELECTION
There are four band selector buttons located
Just beneath the LCD display.
BAND
FRIQUENCY RANGE
FROGRAM TYPE
FM
LW
MW
SW
87.5~108 MHz
150~519 kHz
520~1710 kHz
Standard FM
Longwave
StandardAM
1.711~29.999 MHz
SW/13 Sub-Bands
1.Turn radio on by pressing "POWER{
button. Display will show last band and
frequency selected.
2.By pressing any one of the four band
selector buttons the display shows the
band selected and a random frequency
within that band.
NOTE
When you select SWyou only have to press
The button marked "METET" , and then any
one of the numbered buttons depending
upon what band you want to listen to. The
display will show the band you selected and
a random frequency within that band.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNING MODE
ADJUSTING THE ANTENNA
Locate the band you want to listen to in the
following chart and adjust the antenna as
indicated
FREQUENCY
BAND
ILLUSTRATION
ANTENNA TYPES
RANGE
INTERNAL
Rotate radio
for best reception
MW
520-1710 kHz
INTERNAL
Rotate radio
for best reception
LW
FM
SW
150- 519 kHz
TELESCOPIC
Extend antenna all
the way & rotate it
for best reception
87.5- 108 MHz
TELESCOPIC
Extend antenna all
the way for best
reception & do not
rotate
1.711-29.999 MHz
12
Download from Www.Somanuals.com. All Manuals Search And Download.
You may select any frequency using four different tuning methods:
Direct Tuning
Manual Tuning
Scan Tuning
Memory Tuning
DIRECT TUNING
You may "KEY IN" a specific band (120m,
49m,16m) by pressing the appropriate
button. The exact station is then selected by
pressing the buttons corresponding to the
station frequency.
Example :To tune 100.70 MHz on the FM band, follow this procedure:
1.Press the POWER button to turn on the
radio.
2.Press the button marked, FREQ
( "Frequency" )
3.Press the corresponding buttons,
marked [1], [0], [0], [.],[7],[0].That
exact frequency will now show up in
the display.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Press the button marked "ENTER"
within twelve seconds. The frequency
and band will now show up in the display.
The SIGNAL STRENGTH will also show.
NOTE: Be sure to press the decimal point
[.] in 100.70 MHz, otherwise the display will
show "SW" , [10.070 MHz] automatically.
5.Extend the antenna all the way and rotate
for best FM reception.
6.Adjust the VOLUME and TONE controls
for the desired sound.
7.When selecting a stereo FM station,
make sure the FM mode switch is in
the STEREO position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUALTUNING
To select a station you do not know the
frequency of , use the MANUAL TUNING
[V] button or the ROTARY TUNING control
on the side of the radio .
1.Press the POWER button to turn on
radio .
2.Select a band.
] [ V
or [V] buttons to
3.Press repeatedly the
reach a desired frequency. Press and
] [ V
hold the or [V] buttons for at least a
half second or more to change
frequencies rapidly.
OR Rotate the TUNING knob until the
desired frequency or station is tuned in
using the SIGNAL STRENGTH
INDICATOR in the display for the best
reception.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
[V]
When you repeatedl press the[ ]
buttons, the frequencies change in
increments of :
or
Turning the ROTARY TUNING Knob with
D
the TUNING SPEE CONTROL set on
FAST wil l change each band as follows:
FM : 100 kHz
LW : 9 kHz
MW : 9 kHz/10 kHz
SW : 5 kHz
FM: 50 kHz (or 100 kHz)
LW: 9 kHz
MW: 9 kHz or 10 kHz
SW: 5 kHz
When set on SLOW , the frequencies
change as follows:
F M : 50 kHz
LW : 1kHz
MW : 1kHz
SW : 1kHz
With the TUNING SPEED CONTROL set on
G
LOCK , ROTARY TUNIN wil l not function.
4.Adjust the VOLUM E and TON E controls
as you like.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SCAN TUNING
Use scan tuning to quickly locate a station
or to monitor several stations within a
specific band.
1. Turn o n r a d i o b y p r e s s i n g P O W E R
b u t t o n .
2 . S e l e c t a b a n d .
3 . A d j u s t a n t e n n a o r r a d i o p o s i t i o n d e -
p e n d i n g o n s e l e c t e d b a n d .
AM
SW
FM
17
Download from Www.Somanuals.com. All Manuals Search And Download.
[
[
4.Press and hold the
or [V] buttons for
at least a half second or more and the
radio will scan all the frequencies in that
band, and will stop automatically each
time it lands on an active station. Signal
strength is recorded on the SIGNAL
STRENGTH INDICATOR.
1
2
3
4
5
6
7
[
[
5.Press and hold the
or [V] buttons again
to resume scanning. When you reach the upper
or lower limits of the band, the scanning starts
all over again as long as the button is depressed
once more.
6.Adjust the VOLUME and TONE controls
as you like.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMORY TUNING
Yo u m a y s t o r e u p to e i g h t e e n d i f f e r e n t
f r e q u e n c i e s o n t h e S W / F M b a n d s a n d
u p t o n i n e d i f f e r e n t f r e q u e n c i e s o n e a c h
o f LW/ M W b a n d s fo r i n s t a n t s e l e c t i o n
o f y o u r f a v o r i t e s t a t i o n s .
S t o r i n g a F r e q u e n c y
1.Press POWER button to turn on radio .
2.Turn to any frequency using any of the
previously mentioned tuning methods.
3.Press the button marked "M" for
MEMORY it will start flashing in the
ddisplay for 15 seconds during which time
press any of the buttons marked 1-9 on
the keyboard and your station will be
stored in that memory position. For the
SW/FM bands frequencies press 1-9 and
then 01-09 for each 18 memory positions
on FM and SWbands. The display will show
the memory position the station is now stored
in. You may store your stations in any
sequence you want. You do not have
to start with
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECALLING A FREQUENCY
1. Press POWER button to turn on radio.
2.Select a band in which a station is stored
that you want to recall.
3.Press any of the NUMBERED buttons for
a desired station and the radio will
instantly tune to it and display that
frequency and the MEMORY position
number. If you want to change to
another stored station, just press any
other numbered button for access.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK RADIO OPERATION
With this receiver you can fall asleep to your
favorite station by pressing the SLEEP
button, or wake you to the morning, news,
or an alarm buzzer. Make the following
settings with the POWER off!!
Setting theAlarm
1.Press STANDBY button so display shows
0:00.STANDBY will flash for 15 seconds.
1
2
3
4
5
6
7
2.Press the numbered buttons to activate
turn-on time using 24 hour time, in hours
and minutes. For example, to set the
radio to turn on at 1:30 PM each day,
press the buttons until the display shows
13:30. If the wrong number was keyed-
in, delete it by pressing the CANCEL
button marked "C" . One time for each
number. Then press the correct
number for the time you want.
3.Whenyoureachyourdesiredturn-on
time, press ENTER, STANDBY stops
flashing, your turn-on time is locked in.
For 2 to 3 seconds, the clock returns to
the current time automatically.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4.To verify, press STANDBY button again.
Press STANDBY once more and the
clock returns to the current time.
DIRECT ACCESS
5.You may select radio or buzzer alarm to
wake you by setting STANDBY:BUZZER/
RADIO selector switch .
6. To cancel the ALARM time, press
DIRECT ACCESS
STANDBY and "C" [CANCEL] button.
Setting the Sleep Timer
1 . T h e s l e e p t i m e r a l l o w s t h e u s e r t o
s e t t h e a u t o - s h u t off i n 3 0 o r 1 5
m i n u t e s d e c r e m e n t s f r o m 9 0 m i n u t e s
t o 1 5 m i n u t e s .
To s e t a u t o - s h u t off , p r e s s S L E E P
b u t t o n 3 , L C D w i l l s h o w
f r e q u e n c y r e a d - o u t , 6 0 ( a u t o s h u t off
Time) a n d t h e i c o n .
Press SLEEP button to change the
required auto-shut off time, release the
button when shut off time desired is
reached.
2.To turn off the radio before it automati-
cally turns itself off, press the POWER
button.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIALTUNING TECHNIQUES AND CONTROLS
In addition to the standard tuning oper-
AMNARROW/WIDE
Aations described previously , use the
following controls for special operations.
SELECTIVITY SWITCH
Some stations transmit their signal so that
very little space exists between their
RF G A I N CONTROL
airspace and the station next to them on the
band. If, while tuning, you encounter
interference, caused by the signal from an
adjacent station, press the button for the
band you are listening to and select the
NARROW position. The interference is
reduced or muted.
This control adjusts the receiver's
Sensitivity. For LW,MW SWreception
rotate the control to the MAX position,
this provides the maximum sensitivity.
when you listen to the MW, standard
aM band, or LW band through external
antenna, rotate the control only as far as
needed to obtain a good signal .If you
turn the knob further you might hear a
distorted signal . For weak stations,
rotate the control to the MAX position.
For full reception, leave the switch in the
WIDE position.
If you encounter interference, adjust the
control in both directions until you obtain
the best compromise between your station
and the interference.
If you plan to listen to Morse code, referred
to as CW (continuous wave), set the BFO
switch to ON position. If you encounter
too much noise as you tune, set the AM
NARROW/WIDE switch to NARROW
position.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HEADPHONE USE
LOCK SWITCH USE
Using the LOCK Switch prevents
While not a control, you may consider using
HEADPHONES to obtain the best audio
clarity when listening to SW. Since many
SW stations broadcast only marginal
signals, using HEADPHONES will enable
you to distinguish between the signal and
the noise usually encountered at night. Be
sure that the HEADPHONES terminate in a
1/8 inch plug, which is inserted into the
HEADPHONE jack located on the left side
of the radio, marked with symbol
When the HEADPHONES are plugged in,
the speaker is muted.
unauthorized operation of the radio and will
also prevent the station you are listening to
from being changed. When the LOCK
switch is moved to its up
position, the
POWER button and TUNING controls are
completely disabled. If the radio is on when
the LOCK switch is moved to its up
position, you will not be able to turn it off.
If the radio is off, with the LOCK Switch in
its up
position, you will not be able to
turn it on. This will also prevent it from being
turned on by accident, when packed in a
attache case. To release the LOCK Switch,
simply move the switch down.
Because the radio is capable of receiving
FM multiplex stereo, Stereo HEADPHONES
Should be used.Whenlistening to stereo
FM, be sure that the FM: STEREO/MONO
switch is set to the STEREO position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNA
R SWITCH
Located in battery compartment of the unit,
is a switch marked, 9K/10K. This switch
selects the incremental frequency STEPS
for the MWband, depending upon your
geographic location. In the USA, 10K STEPS
are used, so the switch should be set to its
10K Position. In other parts of the world
where they use 9K STEPS, move the switct
to the 9K Position.
To obtain optimum performance from this
unit, especially when listening to SW/SSB/
CWanexternal antenna should be used, if
at all possible. The antenna is connected to
the EXTERNALANTENNAADAPTER and
then plugged into the EXTERNALANTENNA
jack located on the left side of the radio.
AM EXT ANT
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Cassette Recorder
The Sangean Cassette Recorder built in to your Sangean Model ATS-818ACS is a top quality,
precision cassette recorder providing a number of features to further enhance your use and
enjoyment of your Sangean radio .Your Recorder can:
A: Allow you to play your favorite cassettes.
B:Allow you to record using the built-in microphone.
C:Allow you to record any program formAM(MW,LW or SW) FM.
D: Allow you to record any program fromAM(MW,LW or SW)/FM at any preprogrammed time
To Play a Cassette Tape
1.Press STOP/EJECT [30] to open the
cassette door.
31
30 29 28 27 26
32
2.Insert a cassette with the full reel on the
right, the side to be played facing you and
the exposed tape pointing upward.
3.Close the cassette compartment door.
4.Press PLAY[27].
5.Adjust the Volume Control[37] to your
desired listening level.
Using Fast-Forward (FF) and Rewind.
1.To Fast-Forward the tape ,press FAST-
FORWARD[29].
2.Press STOP/EJECT [30] to stop
Fast-Forward.
3.To Rewind rapidly press REWIND[28].
4.Press STOP/EJECT to stop the rewind
motion.
31
30 29 28 27 26
32
Caution: In either Fast-Forward or Rewind,
always press the STOP/EJECT [30] before
changing tape motion. Do not switch from
Fast-Forward to Rewind without pressing the
STOP/EJECT button between the two
operations. If you let the tape come to the
end in either Fast-Forward or Rewind the
tape will automatically stop.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
To Record with the Built-in Microphone
Your cassette recorder has a built-in condenser microphone [21] on the front of the cabinet.
To record with the built-in microphone follow the following steps:
1.Select CrO2/NORMAL Tape Selection
Switch [38]
2.Press RECORD [26] and PLAY [27] but-
tons simultaneously. RECORD will re-
main in the locked position and the
31
30 29 28 27 26
32
RECORD LED [23] will illuminate in-
dicating recording is in progress.
Note: The tape will stop automatically when
it comes to the end of a side. At this point
the RECORD button and the PLAY button
will disengage and the recording will be
terminated.
3. To listen to your recording it will be
necessary to Rewind the tape, Stop the
tape, and then press the PLAY button
[27].
To Record from the Radio
To record the current tuned program follow these steps:
1.Install blank tape and select CrO2/
NORMAL Tape Selection Switch [38].
2.To reduce interference when recording
AM(MW,LW or SW) switch BEAT CUT
Switch [40] to on position.
31
30 29 28 27 26
32
3.To listen to recording, rewind tape and
press PLAY [27].
Note: The volume and balance controls
have no effect during recording .They only
Effect the play operation. The recording level
is set automatically by the alc (Automatic
Level Control) circuit.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To Record from the Radio using the Program Feature
1.Turn on radio and tune to the desired
station.
2.Turn off the radio, push STANDBY but-
ton [9] and set time for required start of
recording.
31
30 29 28 27 26
32
3.Switch Standby Buzzer /Radio Switch [12]
to the Radio position.
4.Switch Timer Recording On/Off Switch
[39] to On position.
5.Select CrO2/NORMAL Tape Selection
Switch [38].
6.Push RECORD [26] Play [27] Buttons
simultaneously.
Note: The recording will continue until the
cassette tape reaches the end of a side and
It will then cease automatically and
disengage the tape.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL SSB/CW RECEPTION TECHNIQUES
Many stations transmit unmodulated
telegraph transmissions in the shortwave
band. To receive these special Morse code
characters, the radio uses a special circuit
a beat-frequency oscillator, to modify the
transmitted signal so that you can hear it.
this particular type of telegraph trans-
mission is called continuous wave(CW)
transmission .
Many stations transmit voice signals with a
suppressed carrier in the single side band.
(SSB), part of the radio transmission
spectrum that lies to the side of the primary
frequency signal. Many amateurs who
operate transmit below 10 Mhz general ly
use the lower side band (LSB). Above 10
MHz, they usually use the upper side band
(USB). Commercial utility stations generally
use the USB. A carrier has to be added to
make these signals audible.
-
TO RECEIVE CW
1.Turn on the radio
2.Extend the antenna fully straight up
3.Set the BFO switch to ON.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Rotate the BFO PITCH control to the
midpoint
-
5.Rotate the RF GAIN control to the MAX
position.
6.Press the SW band button to select the
S W b a n d .
7.Tune in the CW station using the tuning
knob, or enter the frequency using the
direct access buttons.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
8.Adjust the CWtone using the BFO PITCH
control.
9.Reduce strong signals by using the
RF GAIN control. This also reduces
interference and noise.
TO RECEIVE SSB VOICE
1.Turn on the radio.
2.Extend the antenna fully, in a straight up
position.
3.Set the BFO switch to the ON position.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Rotate the BFO PITCH control to the
midpoint.
5.Rotate the RF GAIN control to the MAX
position.
6.Press the SWbutton to select the SW
band.
7.Tune in the SSB station using the tuning
knob, or enter the frequency using the
direct access buttons.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
8.Rotate the BFO PITCH control to adjust
the signal quality.
9.Rotate the RF CAIN control to dampen
strong signals. This can improve signal
clarity as well.
Note :Before choosing another band, set
the RF GAIN control to MAX, and move the
BFO switch to the OFF position.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
This receiver is an example of superior
design and craftsmanship. The following
suggestions will help you care for the
receiver so that you can enjoy it for years.
Keep the product dry .If it does get wet, wipe
it dry immediately. Liquids might contain
minerals that can corrode the electronic
circuits.
Use and store the product only in normal
Temperature environments. High tempera-
tures can shorten the life of electronic
devices, damage batteries, and distort or
melt plastic parts.
Handle the product gently and carefully.
Dropping it can damage circuit boards and
cases and can cause the product to work
improperly.
Keep the product away from dust and dirt,
Which can cause premature wear of parts.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Wipe the product with a dampened cloth
occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or
strong detergents to clean to product.
Use only fresh batteries of the recommend-
ed size and type. Always remove old or
weak batteries .They can leak chemicals
that destroy electronic circuits.
Modifying or tampering with the product's
internal components can cause a malfunc-
tion and might invalidate the product's
warranty.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Semi conductors:
1 LSI .
8 FET.
12 IC
65 Transistors
60 Diodes.
2 LEDS.
Circuit:
F M
AM( LW ,M W, SW )
:Heterodyne
Double-conversion heterodyne
Frequenc y range:
FM :
LW :
MW :
S W
87.5-108 MHz
150-519 kHz
520-1710 kHz
1.711-29.999 MHz
i n which divided into 13 shortwave bands
120M 2.300- 2.495 MHz
90M 3.200- 3.400 MHz
75M 3.900- 4.000 MHz
60M 4.750- 5.060 MHz
49M 5.900- 6.200 MHz
41M 7.100- 7.350 MHz
31M 9.400- 9.990 MHz
25M 11.600-12.100 MHz
21M 13.570-13.870 MHz
19M 15.100-15.800 MHz
16M 17.480-17.900 MHz
13M 21.450-21.750 Mhz
11M 25.600-26.100 MHz
Antennas:
LW/M W
S W
built- i n Ferrite bar Antenna
Telescopic Antenna or external Antenna(not included)
F M
Telescopic Antenna
Output:
Nominal 800 mW at 10% T .H.D.
Jacks:
1.D C jack for external power(6V)
2.Headphone jack -3. 5 for mini stereo headphones
3.A M Ex t .Ant . jack.
Recordin g System:
Erasin g System:
Tap e Speed:
A C bias.
Magnetic Erasing
4.76cm/ sec 3%
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Wow & Flutter:
0.35%W/RMS.
125-8000 Hz.
35dB.
Frequency Response:
Signal to Noise Ratio:
Power sources:
DC: 4 each D size batteries
3 each AA size batteries
AC: 6 volt DC (optional adapter negative center)
Dimension:
Weight:
296(L) x 192(H) x 68(T)mm
2000g without batteries
Accessories:
Adaptor (except for certain areas like United
Kingdom, New Zealand,Australia, SouthAfrica, etc.)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
|