ITP-5107S
IP Keyset
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ITP-5107S User Guide
For OfficeServ™ 100, OfficeServ™ 500,
OfficeServ™ 7000 Series
05/2006
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright 2006 Samsung Telecommunications America.
All rights reserved. No part of this manual may be reproduced in any form or by any means—graphic,
electronic or mechanical, including recording, taping, photocopying or information retrieval systems—
without express written permission of the publisher of this material.
Samsung Telecommunications America reserves the right without prior notice to revise information in
this guide for any reason. Samsung Telecommunications America also reserves the right without prior
notice to make changes in design or components of equipment as engineering and manufacturing
may warrant. Samsung Telecommunications America disclaims all liabilities for damages arising from
the erroneous interpretation or use of information presented in this guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ABOUT THIS BOOK ....................................................................................1
THINGS YOU SHOULD KNOW ................................................2–6
ASSEMBLING YOUR KEYSET ........................................................7
ITP-5107S SETUP....................................................................................8–13
OUTSIDE CALLS
Making an Outside Call................................................................................................14
Answering an Outside Call..........................................................................................14
Universal Answer ..........................................................................................................14
Recall/Flash ......................................................................................................................15
Busy Line Queuing with Callback ............................................................................15
Canceling Callback ........................................................................................................15
INTERCOM CALLS
Calling Other Stations ..................................................................................................16
Answering Intercom Calls ..........................................................................................16
Answer Modes ................................................................................................................16
Busy Station Callback....................................................................................................17
Busy Station Camp-on..................................................................................................17
Calling Your System Operator....................................................................................18
CALL PROCESSING
Holding Calls ............................................................................................................19–20
Transferring Calls ....................................................................................................20–21
Transfer with Camp-On................................................................................................21
Transfer to Voice Mail....................................................................................................21
Call Waiting ......................................................................................................................21
Conference Calls ............................................................................................................22
Forwarding Calls......................................................................................................23–24
Call Pickup ........................................................................................................................25
My Group Pickup............................................................................................................25
Privacy Release................................................................................................................26
Download from Www.Somanuals.com. All Manuals Search And Download.
DIALING FEATURES
Speed Dialing ..................................................................................................................27
Programming Personal Speed Dial Numbers ..............................................27–28
One Touch Speed Dialing............................................................................................28
Last Number Redial ......................................................................................................28
Manual Retry with Redial ............................................................................................29
Save Number with Redial............................................................................................29
Chain Dialing....................................................................................................................29
Automatic Redial/Retry................................................................................................29
Pulse to Tone Changeover ..........................................................................................30
Memo Redialing..............................................................................................................30
PAGING AND MESSAGING
Making an Internal Page..............................................................................................31
Making an External Page ............................................................................................31
All Page ..............................................................................................................................31
Meet Me Page..................................................................................................................32
Call Park and Page..........................................................................................................32
Messages—Set and Cancel ........................................................................................33
Returning Messages......................................................................................................33
Programmed Messages................................................................................................34
CONVENIENCE FEATURES
Do Not Disturb ................................................................................................................35
One Time DND ................................................................................................................35
Mute ....................................................................................................................................35
Background Music ........................................................................................................35
Established Call Pick-Up ..............................................................................................36
Appointment Reminder/Alarm Clock ....................................................................36
Door Phone Calls............................................................................................................37
Executive/Secretary Hotline ......................................................................................37
Group Listening ..............................................................................................................38
Account Codes ................................................................................................................38
Locking Your Keyset ......................................................................................................38
Manual Signalling ..........................................................................................................39
Off-Hook Voice Announce ..........................................................................................39
OHVA Block ......................................................................................................................40
OHVA Reject ....................................................................................................................40
In Group/Out of Group ................................................................................................40
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMIZING YOUR KEYSET
AME Password ................................................................................................................41
Auto Camp-On ................................................................................................................41
Select Ring Tone ............................................................................................................41
Change Your Passcode ................................................................................................41
Set Answer Mode (Intercom) ....................................................................................42
Set Answer Mode (CO) ................................................................................................42
Automatic Hold ..............................................................................................................42
Headset Operation ........................................................................................................42
Hot Keypad ......................................................................................................................43
Key Confirmation Tone ................................................................................................43
Rejoining a Page ............................................................................................................43
Ring Preference ..............................................................................................................43
Auto Answer CO Calls ..................................................................................................44
Display Speed Dial Name............................................................................................44
Caller ID Review All........................................................................................................44
Secure OHVA ....................................................................................................................44
DISPLAY FEATURES
Interactive Display Keys ..............................................................................................45
Directory Information ................................................................................................ 45
Call Log ..............................................................................................................................46
Dial by Name....................................................................................................................46
Call Progress Displays ..................................................................................................47
Display Number Dialed ................................................................................................47
Call Duration Timer........................................................................................................47
Auto Timer ........................................................................................................................47
Timer Function ................................................................................................................47
Viewing Message Indications ....................................................................................48
Alarm Reminder Messages..................................................................................48–49
Personal Speed Dial Names........................................................................................49
Station Names .................................................................................................................49
Managing Key Assignments .......................................................................................50
LCR with Clear .................................................................................................................50
Backspace with LCR ......................................................................................................50
Text Messaging ......................................................................................................51–52
Caller ID .....................................................................................................................53–57
ANI .............................................................................................................................54–57
CLI ..............................................................................................................................54–57
Download from Www.Somanuals.com. All Manuals Search And Download.
SVMi E-Series....................................................................................................58
Accessing your Mailbox ............................................................................................59
SVMi E-Series Subscriber Services Menu Diagram ....................................60–61
Getting Started ...............................................................................................................62
Listen to your Messages .............................................................................................62
Subscriber Services Menu .........................................................................................62
Listening to Old or New Messages .........................................................................63
Group New or Old Messages .....................................................................................64
Record and Send a Message......................................................................................64
Access Manager ......................................................................................................65
Personal Greetings ................................................................................................67
Mailbox Administration .......................................................................................69
Message Broadcast ......................................................................................................71
Personal Services ....................................................................................................72
Personal Administration Settings ............................................................................73
Keyset User Features ....................................................................................................74
Shortcuts ..........................................................................................................................76
Interactive Displays .......................................................................................................76
PERSONAL SPEED DIAL NUMBERS ............................77–78
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THIS BOOK
Samsung’s new OfficeServ Technology keyset model, ITP-5107S, is part of the
OfficeServ 100, OfficeServ 500, and OfficeServ 7000 Series.
The ITP-5107S IP keyset represents a new concept of Internet phone, in that it uses
an IP address to Send/Receive voice and data. For voice communications, the ITP-
5107S uses the data network line already in place in most offices and increasing
number of homes.
The ITP-5107S keysets incorporate an LCD screen, which provides important infor-
mation for the user, to make using the keyset easier and more convenient.
Your keyset is the most visible part of your telephone system. Please take the time
to study this guide and to become familiar with the operation of your keyset. Keep
this guide handy, as you may need to look up instructions for infrequently used
features.
Learning to use your keyset correctly will make everyday telephone communica-
tions a breeze.
This book is written based on the factory default settings for the feature access
codes. Sometimes, due to programming requirements, these codes may be
changed. If you find that a feature code does not work as described in this book,
please contact your installation and service company to determine the correct
code.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
THINGS YOU SHOULD KNOW
USER ORIENTATION
The ITP model telephones are called IP keysets.The IP keyset incorporates buttons
or“keys”that are used to access or activate the many features of your office phone
system. The ITP-5107S keyset incorporates 7 programmable buttons. Any of the
system features or functions can be programmed to these buttons.
The three buttons above the row of programmable buttons are soft keys. These
buttons assist in the use of the system features and functions.
Lines from the telephone company are“C.O. lines.”Calls on these lines are referred
to as “outside calls.”Your system can have individual C.O. line keys or lines may be
assigned to groups. When they are in a group, you access a line by dialing an
access code or pressing a route button. For example, dial 9 or press a“LOCAL”but-
ton to get a local outside line. If Least Cost Routing is used, pressing the“LCR”but-
ton will automatically select a preprogrammed C.O. line according to what digits
are dialed. Each line in the system is numbered, beginning with 701, then 702, 703,
etc.
Direct Station Selection (DSS) buttons are programmed to ring specific stations.
You can press a DSS button instead of dialing the extension number.
CALL INDICATIONS
The buttons on your phone have light emitting diodes (LEDs).These are tri-colored
LEDs that light green, red or amber (green and red together).
Intercom calls, also called internal calls, always appear on your CALL buttons.They
will always light green.You can have up to eight CALL buttons, but at least two are
recommended.
Outside calls appear on individual line buttons if they are assigned. When an indi-
vidual line is not assigned to its own button, it will appear on a CALL button.
Your outside calls will light green on your keyset and red on other keysets. You
never lose sight of your calls while they are on hold.They stay right where you put
them and are identified with a green flashing light.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Some simple rules to remember:
•
•
•
•
Any steady LED indicates the line or feature is in use.
A fast flashing green LED indicates a new call ringing in.
A slow flashing green or red LED indicates a call is on hold.
A slow flashing amber LED indicates a recall to your keyset.
FULL DUPLEX SPEAKERPHONE
All ITP keysets are speakerphones. Pressing the FLASHING CALL BUTTON will
answer an incoming call on the speakerphone. Pressing the SPEAKER button will
release the call on the speakerphone.
Switching from the handset to the speakerphone is easy. Simply press the SPEAK-
ER button and hang up the handset.
VOLUME CONTROLS
The ITP-5107S keyset uses the UP and DOWN buttons to adjust the ringer volume
while the keyset is ringing, the speaker volume while the speakerphone is in use
and the handset volume while you are listening. These three levels will be stored
in memory until changed. If background music is turned on at your keyset, the vol-
ume buttons will also control the level of music. The volume of pages heard
through the speaker of a keyset can be adjusted during a page announcement by
using the volume buttons.There are 16 levels for each volume setting.The volume
of off-hook ring is controlled by a user-programmable setting.
TERMINAL STATUS INDICATOR
The terminal status indicator light is positioned on the top right corner of the key-
set above the display. The terminal status indicator is a tri-colored (red, green, and
amber) light that provides greater visibility of your keysets status than the indi-
vidual button LEDs. The terminal status indicator provides the following indica-
tions:
•
•
•
•
•
•
Busy/Off Hook
Intercom Ring
Outside Call Ring
Recall Ring
Message Waiting
Do Not Disturb
Steady Red
Flashing Red
Flashing Green
Flashing Amber
Flashing Red
Fast Flash Red at 1 Second Intervals
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFERENCE BUTTON
The CONFERENCE button allows the user to set up a call with up to 5 parties (sta-
tion or trunk).
TRANSFER BUTTON
Transfer is used to send any call to another extension in one of two ways.You can
do a screened transfer by informing the other extension who is calling or you can
do a blind transfer without notification.
HOLD BUTTON
The HOLD button maintains the call at your keyset, while enabling you to call
other stations or consult coworkers in confidence.
SPEAKER BUTTON
The SPEAKER button allows you to initiate a conversation from the keyset with-
out lifting the handset or switch to speaker phone mode if you are currently on
handset.
FEATURE ACCESS CODES
This user guide is written based on the default access code for using system fea-
tures. If the system numbering plan has been changed some of the access codes
may not be correct.Your installing company can inform you of the correct codes.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM TONES
The system provides several tones to assist you. Some of these tones are already
familiar to you.
Intercom Dial Tone—A steady tone that indicates you can begin dialing.
DIAL TONE
CONTINUOUS
Ringback Tone—Indicates the station you dialed is ringing.
RINGBACK TONE—1000 ms ON/3000 ms OFF
CONTINUOUS
Busy Tone—Indicates the station you dialed is busy.
BUSY TONE—500 ms ON/500 ms OFF
CONTINUOUS
DND/No More Calls Tone—Fast busy tone indicates the station you dialed
is in the Do Not Disturb mode or cannot receive any more calls.
DND/NO MORE CALLS TONE—250 ms ON/250 ms OFF
FOR TEN SECONDS
Transfer/Conference Tone—Indicates your call is being held and you
can dial another party.
TRANSFER/CONF TONE—100 ms ON/100 ms OFF
CONTINUOUS
Confirmation Tone—Very short beeps followed by dial tone indicate you
have correctly set or canceled a system feature.
CONFIRMATION TONE—50 ms ON/50 ms OFF
FOR ONE SECOND
(programmable)
Error Tone—A distinctive two level beeping tone indicates you have done
something incorrectly.Try again.
ERROR TONE—50 ms of tone 1/50 ms of tone 2
FOR THREE SECONDS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ITP-5107S
Soft Button
LCD Panel
Status Indicator
Scroll Button
Programmable
Buttons (7)
Keyset
Support
Volume Button
Redial Button
Conference Button
Transfer Button
Hold Button
Dial Button
Microphone
Speaker Button
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING YOUR KEYSET
•
•
Place the keyset face down on a flat surface.
Insert notched ends of the support bracket into the channels located in the
upper section of the bottom panel. Push towards the top of the keyset to lock
in.
•
•
Plug the handset cord into the jack marked with the
symbol.
Route the handset cord out the RIGHT side of the keyset as you look at it face
down.
•
•
Plug an eight-conductor ethernet cable, from the wall, into the jack marked
LAN on the back of the keyset.(Connect the ITP keyset to any port on the local
network).
Plug the power connector, from the power adapter provided, into the power
jack on the back of the keyset. The power adapter is not required if the ITP is
connected to a LAN connection that provides power over the ethernet. The
ITP-5107S supports the power over ethernet feature when it is connected to
a IEEE 802.3af compliant LAN switch or power injector port.
IMPORTANT NOTE:
•
To prevent damaging the keyset, only use the Power Adapter that came with
the 5107S keyset.
•
This manual assumes that the ITP keysets are connected to a functioning local
IP network. The local IP network must be able to communicate with the MCP
and MGI card in the OfficeServ 100, OfficeServ 500, or in the OfficeServ 7000
Series systems over IP. This is assumed regardless of whether the IP keyset is
on a local or remote network.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ITP-5107S SETUP
INITIALIZING THE ITP-5107S
Initially the ITP-5107S IP keyset will need to be setup to operate within the users
network.The Setup Menu is also used to make changes to the keyset, in the event
that the system information should change. The option chosen via scroll key will
be highlighted.
The station numbers will be automatically set by the OfficeServ 100, OfficeServ
500, and the OfficeServ 7000 Series systems once the necessary information has
been entered into the IP keyset. Enter ID and password of the server, as described
below to register the phone.
See your system administrator for specific Network and Server addresses. The
addresses necessary to set up the ITP-5107S are:
•
•
•
•
•
•
IP Address of the ITP
Network Gateway Address
Subnet Mask
IP Address of System’s MCP
User ID
Password
SETUP MENU
TO GET TO THE SET-UP MENU, UNPLUG THE POWER FROM THE ITP-5107S
PHONE OR UNPLUG THE LAN CABLE IF USING POWER OVER ETHERNET,
PRESS AND HOLD THE , BUTTON ON THE DIAL PAD WHILE PLUGGING IN THE
POWER CORD OR LAN CABLE IF USING POWER OVER ETHERNET BACK INTO
THE PHONE. NOW RELEASE THE , BUTTON.
>1.SYSTEM EASY WIZARD
2.SYSTEM INFORMATION
Other items not shown on screen when scrolling down.
3.NETWORK SETUP
5.SYSTEM SERVER SETUP
6.FACTORY RESET
4.LOAD & UPGRADE SETUP
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6.FACTORY RESET
7.REBOOT
NAVIGATING THE MENUS
Once the IP setup menu is displayed, you can move to each menu by using the
buttons as described below:
•
•
•
•
•
•
The [0]~[9] dial buttons are used to directly choose a menu, or sub-menu
options.
The volume [M]~[L] buttons are used to move the cursor up or down to
scroll through menu items.
The SPEAKER button is used to select a menu item or to save data after entry.
It functions as an “ENTER” or “OK” button.
The HOLD button will take you out of the current sub-menu to one menu
level up to previous screen. It functions as an “ESCAPE” or “CANCEL” button.
In some entry fields, the HOLD button is used to backspace the cursor or to
delete entered data.
G
The [,] button on the dial pad is used to enter [ ] between IP address octets.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU STRUCTURE
The IP SETUP MENU is configured as follows:
1. SYSTEM EASY WIZARD
This option will guide you through setting up all required parameters for con-
necting the ITP keyset to your system.
2. SYSTEM INFORMATION
1. Version Info: Provides boot rom, software, DSP, and hardware version
information.
2. Network Info: Displays network mode, IP address of phone, network, and
gateway information.
3. Netmask
4. Gateway
Note that items 2 to 4 are only displayed when setting Manual IP.
3. NETWORK SETUP
This menu allows you to individually setup the same parameters found in the
Easy Wizard.
4. LOAD & UPGRADE SETUP
1. Upgrade TFTP Server:The IP address of the TFTP server containing the ITP
software.
2. Upgrade Start: Starts the ITP software upgrade process.
5. SYSTEM SERVER SETUP
1. Server IP Address:The MCP’s IP address.
2. Server ID: The ID assigned to your ITP (see your phone administrator for
this information).
3. Server Pass:The password assigned to your ITP (see your phone adminis-
tratror for this information).
6. FACTORY RESET
This option resets ITP to factory default settings.
7. REBOOT
This option reboots the ITP.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE NETWORK PARAMETERS
Utilize the following programming steps to program the ITP-5107S keyset to
operate within the users network. YOU CAN SELECT THE SYSTEM EASY WIZARD
TO PROGRAM ALL REQUIRED NETWORK PARAMETERS IF YOU WANT TO SET
UP THESE PARAMETERS INDIVIDUALLY FOLLOW THE INSTRUCTIONS BELOW.
Network Parameter Setup
Get into the SETUP MODE as shown on page
8. From the Setup, Main Menu, select [3. NET-
3.NETWORK MODE SET UP
WORK SETUP] to set or modify the network
parameters. Scroll to this option using the
volume [M]~[L] button and press SPEAKER.
Select the Network Mode Setup and press
SPEAKER, the LCD will display this message.
>1.MANUAL IP
2.DHCP
•
•
If [1. MANUAL IP] is selected, the user must enter the IP address of the IP key-
set. Then enter the subnet mask, and gateway value for the customer net-
work.
If [2. DHCP] is selected, the IP address, subnet mask, and gateway value will
be obtained automatically (if a DHCP server is present).
Setting IP Manually
•
From the “Network Mode Setup” Menu,
select [1. MANUAL IP] and press
SPEAKER. Next, press the HOLD button
twice to get to the NETWORK SETUP
MENU as seen here.
1.NETWORK MODE SET UP
2.IP ADDRESS SET UP
3.NETMASK SETUP
4.GATEWAY SETUP
Enter the IP keyset’s IP address, the net-
work’s netmask and gateway as shown.
•
Select the [2. IP ADDRESS SET UP]
menu and press SPEAKER, the LCD will
display this message and the user can
enter its IP address.
INPUT IP ADDRESS& PRESS OK
xxx.xxx.xxx.xxx
Check if there is any currently saved IP address of the phone on the LCD. If the IP
address has not been set, the LCD displays nothing. The user can enter the IP
address using [0]-[9] dial buttons and [,] button for entering a “.” Save that IP
address by pressing the SPEAKER button. Use the HOLD button to backspace.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Select the [3. NETMASK SET UP] menu
and press SPEAKER, the LCD will display
the following message and the user can
enter a new Netmask IP address. Use the
HOLD button to backspace.
INPUT NETMASK & PRESS OK
xxx.xxx.xxx.xxx
Check if there is any currently saved subnet mask address of the phone on the
LCD. If the subnet mask address has not been set, the display will show nothing.
Press any dial buttons from [0]-[9] and [,] button to enter the subnet mask IP
address and then save that subnet mask IP address by pressing the SPEAKER but-
ton. Use the HOLD button to backspace.
•
Select [4. GATEWAY SET UP] menu and
press SPEAKER, the LCD will display the
following message and the user can
enter a new gateway address.
INPUT GATEWAY & PRESS OK
xxx.xxx.xxx.xxx
Check if there is any currently saved Gateway IP address of the phone on the LCD.
If the gateway IP address has not been set, the LCD displays nothing.The user can
enter the gateway IP address by using [0]-[9] and [,] button and can save that IP
address by pressing the SPEAKER button. Use the HOLD button to backspace.
NOTE: In the [3. NETWORK SET UP MENU], [1. NETWORK MODE SETUP] option,
when [2. DHCP] is selected the IP address, Netmask, and Gateway will not be dis-
played on the LCD. Press HOLD to exit to Main Menu.
Load and Upgrade Set/Modify
The fourth item [4. LOAD & UPGRADE SET UP] sets or modifies the IP phone’s
software version. Use extreme caution when upgrading the keyset. Only use this
if you are upgrading your IP keyset firmware.
Select the [4. LOAD & UPGRADE SET UP] item and move to the lower level. The
screen below is displayed.
1.UPGRADE TFTP SERVER
2.UPGRADE START
Select option [1. UPGRADE TFTP SERVER] and enter the IP address of the TFTP
server containing the ITP software. Use [0]-[9] and [,] button to enter the IP
address. Press SPEAKER to save.
Select option [2. UPGRADE START] and press SPEAKER to start the upgrade
process. Press HOLD to exit.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
System Server Setup
From the Main Setup Menu, the fifth item [5. SYSTEM SERVER SET UP] sets or
modifies settings related to registering the phone to the MCP. You can obtain this
information from your system administrator. The screen below is displayed.
1.SERVER IP ADDRESS
You can set/modify the IP address of the MCP at the [1. SERVER IP ADDRESS] item.
The screen below is displayed when you enter the item. The server IP is the IP
address of the MCP2/MCP.
INPUT SERVER IP ADDRESS
xxx.xxx.xxx.xxx
You can confirm the current IP address of the MCP at the LCD panel. The address
is left blank if it is not set. Use the dial buttons from [0]-[9], and [,] to set the IP
address and press the SPEAKER button to save and exit. Select the [2. SERVER
ID] menu. Use the HOLD button to backspace.
INPUT SYSTEM ID
You must input the ID assigned to your ITP phone. See your phone system admin-
istrator to get this value. Press the SPEAKER button to save and exit. Select the [3.
SERVER PASS] item.
INPUT SYSTEM PASSWORD
You must input the password associated with your ID. See your phone system
administrator to get this value. Press HOLD to backspace. Press the SPEAKER but-
ton to save and exit.
Completion of Settings
From the main menu, select the seventh item [7. REBOOT] to save all modified
settings and reboot the ITP-5107S phone.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTSIDE CALLS
MAKING AN OUTSIDE CALL
•
Lift the handset and press an idle outside line button,line group button or dial
a line access code to receive dial tone—OR—press an idle outside line button,
line group button or dial a line access code to receive dial tone through the
speaker—OR—press SPEAKER, receive intercom dial tone and dial a line
access code.
•
•
Dial the telephone number.
Finish the call by replacing the handset.
NOTE: You will receive No More Calls tone when you attempt to make a call and
there is no button available for that line.
•
•
•
If Least Cost Routing is enabled on your phone system, this button may be
labeled LCR or accessed by dialing an access code (usually 9).
If your system is programmed to require an authorization code before making
a call, dial , plus a valid code before selecting a C.O. line.
If your system is programmed to require an account code before making a
call, press the ACC button or dial 47 plus a valid bin number, press the ACC
button again and then select a C.O.line.See Account Codes for more information.
For more information on authorization and account codes, see your system
administrator.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
ANSWERING AN OUTSIDE CALL
•
Lift the handset and you are automatically connected to the ringing call.
See Ring Preference under Customizing Your Keyset—OR—press the FLASHING
CALL button to automatically answer on the speakerphone.
NOTE: If a call is flashing at your keyset but not ringing, you must press the flash-
ing button to answer.
UNIVERSAL ANSWER
Outside lines may be programmed to ring a general alerting device. To answer
calls ringing this device, dial 67 or press the UA button.This device can operate in
any one of the six different ring plans.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RECALL DIAL TONE
Press the NEW button to disconnect your existing call, wait for dial tone and then
make a new call on the same line.
NOTE: If this button does not appear on your keyset, the FLASH button may be
programmed to recall dial tone.
SENDING A FLASH
While on an outside call, press the FLASH button to send a flash to the telephone
company. This is required for some custom calling features or CENTREX use.
NOTE: Flash is not available on an ISDN circuit.
BUSY LINE QUEUING WITH CALLBACK
If you receive a busy signal when you are selecting an outside line, this means that
the line or group of lines is busy.
•
Press the CBK button, if programmed, or dial 44. You will hear confirmation
tone.
•
•
When the line becomes free, the system will call you back.
Lift the handset to answer, wait for dial tone and dial the telephone number
or speed dial number again.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set
a callback, your CBK button will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
CANCELING CALLBACK
A callback will be canceled if not answered within 30 seconds. If you have set a
callback, your CBK button will light.
Your phone may have a maximum of five callbacks to lines and/or stations set at a
time. To cancel a callback:
•
•
Press the CBK button, if programmed, or dial 44. You will hear confirmation
tone.
While you are listening to confirmation tone, press the HOLD button.This will
cancel the oldest set callback.
NOTE: If the hot keypad feature is turned off,you must first lift the handset or press
the SPEAKER button before dialing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERCOM CALLS
CALLING OTHER STATIONS
•
•
Dial the extension number or group number.
Wait for the party to answer. If you hear a brief tone burst instead of ringback
tone, the station you called is set for Voice Announce or Auto Answer. Begin
speaking immediately after the tone.
•
Finish the call by replacing the handset.
NOTES:
1. If you have a DSS button assigned to an extension or station group, you may
press this button instead of dialing the number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
ANSWERING INTERCOM CALLS
•
When your keyset rings, simply lift the handset—OR—press the FLASHING
CALL button to be connected to the calling station.
To finish the call, replace the handset.
•
See Ring Preference under Customizing Your Keyset.
VOICE ANNOUNCE MODE
When another station calls you, your keyset will sound a brief attention tone and
you will hear the caller’s announcement.
•
•
Press the FLASHING CALL button to turn on the microphone and speak
handsfree—OR— lift the handset to reply.
To finish the call, replace the handset.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
ON.
AUTO ANSWER MODE
When another station calls you, your keyset will sound a brief attention tone and
then automatically answer the call.
•
•
Your microphone and speaker are turned on and you can speak handsfree.For
privacy, use the handset.
To finish the call, replace the handset.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
ON.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BUSY STATION CALLBACK
When you call another station and receive a busy signal:
•
•
•
Press the CBK button, if programmed, or dial 44.
When the busy station becomes free, your keyset will ring.
Lift the handset to call the now idle station.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set
a callback, your CBK button will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
BUSY STATION CAMP-ON
When you call another station and receive a busy signal but you do not want to
wait for a callback:
MANUAL CAMP-ON
•
•
Press the CAMP button or dial 45.
The called station will receive off-hook ring tone repeated every few seconds
and its first available CALL button will flash green to indicate your call is wait-
ing.
•
•
Wait for the called party to answer.
The called station must release its first call or place it on hold before answer-
ing your camp-on.
NOTES:
1. If you receive No More Calls tone, that station has no available button to
accept your call. Hang up or leave a message.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
AUTO CAMP-ON
When you want to automatically camp on to a busy station without pressing the
camp on button every time you call a busy station, you can set your phone for
auto camp-on.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 081 to turn on auto camp-on or 080 to turn it off.
Press TRANSFER to store your selection.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLING YOUR SYSTEM OPERATOR
•
•
Dial 0 to call your system operator or group of operators.
If you want to call a specific operator, dial that person’s extension number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press the SPEAKER button before you begin dialing.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CALL PROCESSING
SYSTEM HOLD
•
When you are connected to any call, press HOLD. The call will flash green at
your keyset.If this call appears on a line button at other keysets, it will flash red
at those keysets.
•
To take the caller off hold, press that button and the green flashing light will
go steady green again. Resume the conversation.
NOTE:While on a call, pressing a line button, route button or flashing CALL button
will automatically put your first call on hold and connect you to the new call. See
Automatic Hold under Customizing Your Keyset.
EXCLUSIVE HOLD
To place an outside call on hold at your phone so that other users cannot get it:
•
Press the HOLD button twice.The call will flash green on your keyset and this
line will show a steady red light on other keysets.
•
To retrieve the call, press the flashing green line button or press the HOLD
button a third time.
NOTE: Intercom calls will always be placed on exclusive hold.
REMOTE HOLD
When you wish to place a call on hold at another station. Press TRANSFER and a
dial the station number (or press the appropriate DSS button). Press the HOLD
button.This will place the call on system hold on an available CALL button or Line
Button at the remote station and return you to dial tone.
NOTES:
1. If the destination station does not have any free CALL buttons or line buttons
you will hear No More Calls tone and must return to the other party by press-
ing the TRANSFER button (or the RETURN soft key in the display).
2. Intercom calls cannot be remote held.
HOLD RECALL
If you leave a call on hold longer than the hold timer, it will recall your station.The
button that the call appears on will have a slow flashing amber light.
•
When your phone rings, lift the handset or press the FLASHING CALL button
to answer the recall.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
•
If you do not answer this recall within a pre-programmed period of time, it will
go to the system operator.
CONSULTATION HOLD
When you are talking on an outside line and it is necessary to consult with anoth-
er extension:
•
Press the TRANSFER button; you will receive transfer dial tone. Your call is
placed on transfer hold.
•
•
•
Dial the extension number.
Consult with the internal party.
Press TRANSFER to return to the outside party or hang up to transfer the call.
NOTE:Repeatedly pressing the TRANSFER button will toggle between the outside
party and internal extension. If necessary you may disconnect either one of the
parties by pressing the DROP button.
RETRIEVING CALLS HELD AT
ANOTHER STATION
When a line is on hold and it appears on your keyset, press the line button with the
red flashing light.
When a line is on hold and it does not appear on your keyset, dial 12 plus the line
number or the extension number of the station that placed the call on hold.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
TRANSFERRING CALLS
Transfer is used to send any call to another extension in one of two ways. You can
do a screened transfer by informing the other extension who is calling or you can
do a blind transfer without notification.
•
•
While on a call, press the TRANSFER button and dial an extension number or
group number.Your call is automatically put on transfer hold. OR
Press a DSS button or station group button. Your call is automatically put on
transfer hold.
Hang up when you hear ringing (this is an unscreened or blind transfer).
OR
Wait for the called party to answer and advise him/her of the call and hang up.
If the transfer is refused, you will be reconnected to the outside line when the
called station hangs up or you can press TRANSFER to return to the outside
party. If you wish to send the call to another extension without waiting for the
20
Download from Www.Somanuals.com. All Manuals Search And Download.
first station to hang up, simply press another DSS button. OR
Press the CALL button or C.O. line button to return to the outside party and
begin the transfer process again.
When you are transferring a call to a keyset set for Voice Announce or Auto
Answer, the transferred call will always ring.
NOTES:
1. After the inside party answers, you may alternate back and forth between the
parties by pressing the TRANSFER button.
2. If you receive No More Calls tone, that station has no button available to re-
ceive another call. Press TRANSFER to return to the other party.
3. You cannot transfer an Intercom call by pressing a DSS button.You must press
the TRANSFER button and dial the destination extension number.
TRANSFER WITH CAMP-ON
When you are transferring a call to another station and you receive a busy signal,
you may camp the call on to this station. Simply hang up when you hear the busy
signal. The called party will be alerted that a call is waiting for them.
NOTE: If you receive No More Calls tone, that station has no button available to
receive another call. Press TRANSFER to return to the outside caller.
TRANSFER TO VOICE MAIL
This feature is used to send a call directly to a voice mailbox.Your keyset must have
a correctly programmed VT button to accomplish this.To transfer a call directly to
a voice mailbox:
•
•
While on a call, press the VT button and dial the mailbox number.
Hang up when dialing is completed.
CALL WAITING
If an outside call has been camped-on to your phone or another station has
camped-on to you:
•
•
You will hear a tone in the earpiece and the call that is waiting for you
(camped-on) will flash. In addition the bottom line of the display will indicate
the number of the station or trunk party camped-on.
Press the flashing button to answer; your other call will go on hold automati-
cally if your station has the Automatic Hold feature set. If not, you must press
HOLD and then the flashing button OR
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Finish the first call and hang up; the waiting call will ring.
Lift the handset.
•
NOTE: Intercom calls will not go on Automatic Hold.
CONFERENCE CALLS
You may conference up to five parties (you and four others) in any combination of
outside lines and internal stations in any order.
•
•
While engaged in a conversation, press the CONF button and receive confer-
ence tone.
Make another call, either intercom or outside, press the CONF button and
receive conference tone.
•
•
Make another call or press the CONF button to join all parties.
Repeat the last step until all parties are added.
NOTE: When attempting to add another party to the conference and you are not
able to reach the desired person, hang up. Simply press the CONF button again to
return to your previous conversation.
To drop a party from your conference call:
•
•
Press CONF and dial the extension or line number that is to be dropped.
Press CONF again to reestablish the conference.
NOTE:To leave the conference, hang up. Control is passed to the next internal sta-
tion. If there are no internal stations and you wish to leave outside lines connect-
ed together in a trunk to trunk conference, press the CONF button plus the CALL
button that the call appears on or follow the instructions to drop a party and use
your extension number. When they hang up, the lines will release automatically.
Press CONF to rejoin a trunk to trunk conference.
CONFERENCE SPLITTING
If you are the controlling party of a conference and your keyset has the Auto Hold
feature turned on (See Customizing Your Keyset) and all of the outside lines involved
in the conference appear as buttons on your keyset, you can split the conference
into separate calls as follows:
•
Press any one of the outside line buttons.That outside line will remain steady
green to indicate you are still connected to it. All other outside lines in the
conference will be placed on system hold at your keyset. All intercom callers
in the conference will be disconnected. You may now speak with each caller
privately and transfer them as usual or reestablish another conference.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
FORWARDING CALLS
You may forward your calls to another station, group of stations or an external
telephone number. Program a destination for the type of forwarding you want as
detailed below. If you have FWD ALL, FWD BUSY and FWD NO ANSWER buttons,
press one to turn that forward feature on. A steady red light reminds you what for-
ward condition is activated.
You can clear all call forward conditions set at your station by lifting the handset
and dialing 600.
FORWARD ALL CALLS
To forward all your calls under any condition to another station:
•
•
Dial 601 plus the extension or group number.
Receive confirmation tone and hang up.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. The station that receives a Forwarded All call can transfer the call to the for-
warded station. This is useful when you are expecting an important call but
you do not wish to be disturbed by other calls.
3. When a station user places his/her keyset in Forward All mode and he/she
does not have a FORWARD ALL button, the TRANSFER button will light to in-
dicate Forward All has been set and calls to this station have been transferred
elsewhere.
FORWARD BUSY
To forward calls to another station when you are on the phone:
•
•
Dial 602 plus the extension or group number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPEAKER before you begin dialing.
FORWARD NO ANSWER
To forward calls to another station when you do not answer:
•
•
Dial 603 plus the extension or group number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FORWARD BUSY/NO ANSWER
If you have both a Forward on Busy destination and a Forward No Answer desti-
nation programmed, you may set both of these at the same time:
•
•
Dial 604.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
FORWARD FOLLOW ME
When you want all calls to your extension forwarded to the extension where you
are now:
•
•
Dial 606 plus your extension number.
Receive confirmation tone and hang up.
If you want a specific extension's calls forwarded to your phone (Remote Call
Forward):
•
•
Dial 606 plus the desired extension number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
FORWARD DND
To forward your phone when you activate DND.
•
•
Dial 605 plus the extension number or group number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off you must first lift the handset
or press the SPEAKER button before you begin dialing.
CALL FORWARD OPTIONS
A display keyset may review or change call forward options and destinations. Call
forward access can be done via the keypad or by accessing the keyset display fea-
tures. To review or change call forward options:
•
Press TRANSFER 102.
The display will indicate the current call forward condition and destination
OR
Show 0:FORWARD CANCEL to indicate no forward is set.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Dial 0 to cancel current condition OR
Dial 1-5 to select the forward type OR
Press UP or DOWN to select the forward type.
Press the right soft key to move the cursor.
Dial the destination number (e.g., 202) OR
Press UP or DOWN to select the destination
Press the right soft key to move the cursor
Dial 1 to set OR
•
•
Press UP or DOWN to select YES or NO
Press TRANSFER to store and exit
STATION CALL PICKUP
To pick up (answer) a call ringing at another station, lift the handset and dial 65
plus the extension number of the ringing phone.
If you have a DP key assigned with a station number, you only need to press this
DP key with the flashing light to answer this ringing station.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
GROUP CALL PICKUP
To pick up (answer) a call ringing in any pickup group, lift the handset and dial 66
plus the desired group number or press the flashing GROUP PICKUP button if
available.
GROUP NUMBERS
01-20
01-99
01-99
01-99
OfficeServ 100
OfficeServ 500 M
OfficeServ 500 L
OfficeServ 7000 Series
NOTES:
1. A group pickup button can have an extender for a specific pickup group.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing the access code.
MY GROUP PICKUP
If desired, a new access code can be assigned to pickup ringing calls in the same
pickup group as you are in. Like “66” above except you do not need to dial the
desired group number. See your installation company for the assigned access
code. MY GROUP PICKUP: __________________.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PRIVACY RELEASE
This feature will allow another station to join in our conversation by releasing pri-
vacy on the C.O. from your phone.
To Release Privacy:
While you are talking on a C.O. line and you wish to have other internal parties (or
up to three) join the conversation.
•
Press the PRB button (the PRB button will light steady red). Inform the other
party that he/she may now join the conversation.
After the other party (or parties) has joined the conversation and you wish to
return privacy to the line so that no one else can join the conversation, press the
PRB button a second time, the PRB button will be off.
To Join a Non-Private Conversation:
When someone has informed you that you can join a conversation:
•
•
Press the C.O. line button that he/she has indicated.
OR
Dial the C.O. line number that he/she has indicated.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DIALING FEATURES
SPEED DIALING
You can dial a preprogrammed telephone number stored in the system-wide
speed dial list of numbers 500~999 or from your personal list of numbers 00~49.
Your system may be set for 950 system wide numbers. If so the system speed dial
access codes are 050~999 and the station speed dial codes are 000~049.
•
•
•
With the handset on-hook, press the MEMORY button or dial 16.
Dial the desired speed dial number.
The telephone number is automatically dialed for you.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
PROGRAMMING PERSONAL SPEED
DIAL NUMBERS
You can program frequently dialed telephone numbers in a personal speed dial
list. A station may be assigned up to fifty numbers, 00–49. See your system admin-
istrator to determine the amount assigned to your station.
•
•
•
•
While on-hook, press TRANSFER and then dial 105.
Dial a speed dial number (00–49).
Dial a line or line group access code.
Dial the telephone number to be stored (24 digits maximum). It can include #,
,, FLASH and PAUSE.
•
Press TRANSFER to store the number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
For the purposes of pro-
gramming speed dial num-
bers, the programmable but-
tons are known as A, B, C, D, E
and F.
A B C D E F
•
•
The A button is not used.
The B button inserts a
flash.
•
•
The C button inserts a
pause.
The D button is used for
pulse to tone conversion.If your system uses rotary (or pulse) dialing C.O.lines,
pressing D while entering a speed dial number causes all subsequent digits to
be sent as DTMF tones.
•
The E button is used to hide digits. Display keyset users may want to hide
some speed dial numbers so that they will not show in the display. When you
are entering a telephone number, press E. All subsequent digits will be hid-
den. Press E again to begin displaying digits.
•
•
The F button is used to enter a name. See Personal Speed Dial Names under
Display Features.
Use the HOLD button to clear a speed dial number.
ONE TOUCH SPEED DIALING
You may assign any speed dial number to an already existing One Touch Speed
Dial button for quick and easy dialing of frequently used numbers.
•
•
•
While on-hook, press TRANSFER and then dial 107.
Press a One Touch Speed Dial button.
Dial the speed dial number (00–49 or 500–999) that you want assigned to
this button.
•
Press TRANSFER to store your selection.
To call this telephone number, just press the One Touch Speed Dial button.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
LAST NUMBER REDIAL
To redial the last telephone number you dialed, press the REDIAL buttonordial 19.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. Redial does not apply to intercom calls.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL RETRY WITH REDIAL
While you are on an outside call listening to a busy signal and you want to redial
the same number dialed.
•
Press the REDIAL button.
This will hang up your existing call and manually redial the same number dialed.
You can repeat this operation for a limited number of attempts.
NOTE: If your keyset is programmed with Call Log Blocks then the Redial will
access the call log when pressed.
SAVE NUMBER WITH REDIAL
To save the number you just dialed for later use, press the SNR button before
hanging up.
To redial this saved number at any time, press the SNR button or dial 17.The same
line will be selected for you.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. The saved telephone number is stored in memory until you save another
number.
3. Redial does not apply to intercom calls.
CHAIN DIALING
You may manually dial additional digits following a speed dial number or chain as
many speed dial numbers together as required:
•
After the first speed number is dialed, press MEMORY again and dial another
speed number OR manually dial additional digits following a speed dial num-
ber.
AUTOMATIC REDIAL/RETRY
When you are making an outside call and you receive a busy signal, the system
can automatically redial the number for you. It will automatically redial at a pre-
programmed interval for up to 15 attempts.
•
•
When you hear a busy signal, press the RETRY button.
The system will reserve the line and automatically redial the same number for
you.You will hear the call being made through the keyset speaker.The micro-
phone is muted.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
•
When the called party answers, lift the handset or press the flashing SPEAK-
ER to begin speaking.
NOTES:
1. If you make another call, auto-redial is canceled.
2. To cancel a retry, lift and replace the handset.
PULSE TO TONE CHANGEOVER
When making an outside call on a dial pulse line, press #. All digits dialed after the
# with be sent as tones.
MEMO REDIALING
When you are calling directory information, you can store the number you are
given using the SAVE feature. There is no need for pencil and paper.
•
•
•
While you are talking on an outside call, press SAVE.
Dial the telephone number as it is dictated to you on the keypad.
Press SAVE to store the number.
To dial the number, press the SNR button. It will select the same line and dial the
stored number. If necessary, you can select a different line and then press the SNR
button.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PAGING AND MESSAGING
MAKING AN INTERNAL PAGE
To make an announcement through the keyset speakers in the idle condition:
•
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial the desired zone number 0, 1, 2, 3 or 4.
After the attention tone, make your announcement.
NOTE: If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
MAKING AN EXTERNAL PAGE
To make an announcement through the external paging speakers:
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial the desired zone number 5, 6, 7 or 8.
OR
Dial 9 to page all external zones.
After the attention tone, make your announcement.
•
NOTE: If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
ALL PAGE
To page all designated keysets in internal zone 0 and all external zones at the same
time:
•
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial , or press the ALL PAGE button.
After the attention tone, make your announcement.
NOTE:The LED on the PAGE button will only light when an All Page is in progress.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
MEET ME PAGE
•
•
•
•
•
•
•
Lift the handset.
Press the Meet Me Page (MMPG) button or dial 54.
Dial the desired zone number.
After the attention tone, instruct the paged person to dial 56.
Press WAIT or TRANSFER.
Remain off-hook until the person dials 56 from any phone.
The paged person will be automatically connected with you.
CALL PARK AND PAGE
When you have an outside call for someone who is not at his/her desk, you can
park the call prior to paging. There are two different methods:
MANUAL PARK ORBITS
•
•
While in conversation, press the PARK button.
Entered a desired orbit number (0-9), if the orbit number is busy dial another
orbit number. Display users can press , to automatically place the call in any
available orbit number and see the number in the display.
Remember the selected orbit number.
Replace the handset when finished.
Lift the handset and make a page announcement as previously described
(example:“John Smith park two”).
•
•
•
To retrieve a parked call from orbit:
•
•
Press the PARK button and dial the announced orbit number (0-9).
You will be connected to the parked call.
NOTES:
1. You must have a PARK button or park access code to retrieve and place calls
in park orbits.
2. If the parked call is not retrieved within a pre-programmed period of time, it
will recall your keyset and have a slow flashing amber light. You cannot park
and page intercom calls.
3. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
AUTOMATIC PARK WITH PAGE BUTTON
•
While in conversation, press the PAGE button.The call is automatically parked
at your station.
•
•
Receive page tone and dial a desired page zone number.
Make announcement indicating your extension number or the line number.
Hang up.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
To retrieve an automatically parked call:
•
Dial 10 plus the number that was announced. If you have a PAGPK button,
press it and dial the number that was announced. If you have a PARK button,
press it and dial the announced orbit number.
•
You will be connected to the parked call.
NOTES:
1. If the call is not retrieved within a pre-programmed period of time, it will recall
your keyset and have a slow flashing amber light. You cannot park and page
intercom calls.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
SETTING A MESSAGE INDICATION
When you are calling another station and no one answers or you receive a busy
signal, you can leave a message indication:
•
•
Press the MESSAGE button or dial 43 and receive confirmation tone.
Hang up. The MESSAGE button on the called station will light. Standard tele-
phones receive special dial tone as a message indication or a lit message
lamp,if the phone is equipped with one and they are connected to an 8MWSLI
card (not available on the OfficeServ 100 or OfficeServ 7000 Series) or a
16MWSLI card on the system.
NOTES:
1. A station can have up to five message indications.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
CANCELING MESSAGES
To cancel a message indication that you left at another station, dial 42 plus the
extension number of the station at which you left a message. To cancel all mes-
sage indications left at your keyset, dial 42 plus your extension. Your MESSAGE
light will go out.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
RETURNING MESSAGES
•
Press the MESSAGE button or dial 43.The first station that left a message will
be called automatically. If that station does not answer, your MESSAGE light
will stay on.
•
•
Repeat until all messages have been returned in the order received.
Your MESSAGE light will turn off when all messages have been returned.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
1. Display keyset users can view message indications and return them in any
order. See Viewing Message Indications under Display Features.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
3. If a message has been left at your keyset by a keyset in Auto Answer, you must
manually cancel the message after it has been returned.
PROGRAMMED MESSAGES
When you will be away from your phone for any length of time, you can leave a
programmed station message. Display stations calling you will see this message
and be informed of your status or follow your instructions.
•
Dial 48 plus any of the message codes (01–20) listed on the back of this user
guide.
•
•
To cancel any of these messages you might have selected, dial 48 plus 00.
Press TRANSFER to exit and store your selection.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button.
You can have multiple programmed message buttons (PMSG) and each one can
have a different message code:
•
•
Press any programmed message (PMSG) button. The message is set and the
button will light red. Press the button again to turn off.
Pressing another programmed message (PMSG) button will turn the previous
one off and set a different programmed message.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVENIENCE FEATURES
DO NOT DISTURB
Use this feature when you want to block calls to your keyset.
•
•
While on-hook, press the DND button or dial 401. The DND button lights
steady red to remind you of this mode.
To cancel DND, press the DND button again or dial 400. The DND light turns
off.You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button.
2. If you place your keyset in DND mode and you do not have a DND button,
your TSI button will flash to indicate DND status.
ONE TIME DND
If you are on a call and you do not wish to be interrupted while on that call, you
can press the DND button and place your station in Do Not Disturb. When you
hang up at the end of the call, DND will be automatically canceled and your key-
set will be able to receive new calls. This feature requires a DND button.
MUTE
You can mute the handset transmitter or the microphone during any conversa-
tion:
•
•
Press the MUTE button. It will light red.
To resume speaking, press the MUTE button again. The light turns off.
BACKGROUND MUSIC
When a music source is supplied, you may listen to music through the speaker in
your keyset:
•
•
While on-hook, press the HOLD button to hear music.
Press the HOLD button again to turn music off.
You can set the level of background music by using the VOLUME buttons while lis-
tening to the music. This does not affect the speakerphone level.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ESTABLISHED CALL PICKUP
To pick up an established call in progress at a single line extension connected to a
computer modem on your PC.
•
•
Press the EP button for that station on your keyset and the call is automati-
cally moved to your keyset.
The single line extension on your modem will be disconnected.
NOTE: You must have an assigned (EP button) button on your regular keyset, for
the single line station.
APPOINTMENT REMINDER/ALARM CLOCK
This feature works like an alarm clock. Use it to remind yourself of an appointment
later in the day (TODAY ONLY) or as a daily reminder every day (DAILY).You can set
up to three alarms. Each one can be either a TODAY ONLY or a DAILY alarm.
When the alarm rings, you will hear three short rings repeated three times. Lift the
handset to answer the alarm. If you do not, the alarm will alert you two more times
at five minute intervals.
To set alarms:
•
•
•
Press TRANSFER and then dial 112.
Dial the alarm number 1, 2 or 3.
Dial the time at which you want the alarm to sound. Enter the time as HHMM
(hours and minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY ONLY) or 2 (DAILY) to select the alarm type.
Press TRANSFER to save.
•
•
•
Repeat for each alarm if needed.
To cancel individual alarms:
•
•
•
Press TRANSFER and then dial 112.
Dial alarm number 1, 2 or 3.
Press the HOLD button.
NOTE: Display keysets can show a reminder message. See Alarm Reminder
Messages under Display Features.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
ANSWERING THE DOOR PHONE
When you are programmed to receive calls from a door phone:
•
•
•
You will receive three short rings repeated.
Lift the handset.You are connected to the door phone.
If an electric door lock release is installed, dial 13 to unlock the door.
CALLING THE DOOR PHONE/
ROOM MONITOR
You may call the door phone and listen to what may be happening outside or in
another room.
•
•
Dial the extension number of the door phone.
You will be connected to the door phone and you can listen or have a con-
versation.
•
If an electric door lock release is installed, dial 13 to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button.
EXECUTIVE/SECRETARY HOT LINE
If programmed, an executive and a secretary can have a hot line between them.
When the executive station is in the DND mode, all of its calls will ring the secre-
tary station.
•
•
Either person can press the BOSS button to make a voice call to the other sta-
tion.
Using the hot line will override DND at the other station.This button will light
red when the other station is in use.
To transfer a call to a Boss in DND:
•
•
Press the TRANSFER button followed by the BOSS button.
Wait for the BOSS to answer to announce the call and hang up to complete
the transfer OR
•
Hang up to complete a blind transfer after pressing the BOSS button.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUP LISTENING
When you are engaged on a call and you are using the handset, you may want
other people to hear the distant party’s voice over the speaker:
•
Press the LISTEN button to turn on the speaker.The microphone is not in use,
so the distant party does not hear other parties present in your office.
Press LISTEN again to turn the speaker off and resume private conversation.
Repeat if necessary.
•
•
NOTE: Depending on speaker volume and the acoustics of your office, it may be
advisable to turn the group listening feature off before hanging up.This will elim-
inate a momentary squeal.
ACCOUNT CODES
When equipped with optional equipment, your system will allow calls to be
charged to a specific account.
•
•
During any outside C.O. call, press the account (ACC) button.
Enter the 3 digit account code bin number when prompted, OR
If your button has an extender of 000 enter the account code (maximum 12
characters including Q and #) and press ACC000 again, OR
If your button has an extender other than 000 (001~999) account code con-
tained in that bin will automatically be entered for your.
LOCKING YOUR KEYSET
You can lock your keyset to control misuse of your phone while you are away.You
can unlock it when you return.Your default station passcode is 1234.
•
•
•
•
While on-hook, press TRANSFER and then dial 100.
Dial your four digit station passcode.
Dial 1 to locking outgoing, 2 for locked all calls, or 0 to unlock.
Press TRANSFER to store your selection.
1
2
0
LOCKED
OUTGOING
LOCKED
ALL CALLS
UNLOCKED
NO
Make outside calls
Receive outside calls
YES
YES
YES
YES
NO
ACCESS DENIED
YES
NO
NO
NO
Make intercom calls
YES
YES
Receive intercom calls
38
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SIGNALLING
Use this feature when you want to send a brief 500ms ring burst to another sta-
tion, regardless of the status of your phone (on-hook, off-hook, handsfree, DND, or
ringing).
To send a signal to another station:
•
•
Press the Manual Signalling (MS) button.
You may press the MS button repeatedly to send multiple signals to the des-
ignated station.
NOTE: Your phone must have a Manual Signalling (MS) button with a station
number extender assigned to it.
OFF-HOOK VOICE ANNOUNCE
Keysets may receive a voice announcement while on another call. The calling sta-
tion must have an OHVA button. When you are in DND, you cannot receive OHVA
calls. The OHVA feature will work with intercom and transferred calls.
When you receive an OHVA and secure OHVA is ON, you will hear the announce-
ment in the handset receiver, if you are using the handset. If secure OHVA is OFF
then you will hear the announcement on the speaker, if you are talking on the
handset. If you are using the speakerphone the announcement will always be
heard through the speaker.
To make an off-hook voice announcement:
•
•
•
•
•
Dial the extension number or press the DSS button.
When you receive a busy signal, press the OHVA button.
After the attention tone, begin speaking.
Finish the call by replacing the handset.
Press the flashing CALL button on your keyset. This will place the original
party on hold and allow you to talk to the announcing party.
To return to your first party, press the button corresponding to your original
call. This will disconnect the OHVA call.
•
NOTES:
1. When you are voice announcing to a station close to you, use the handset to
avoid an echo effect.
2. You cannot off-hook voice announce to single line telephones.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (BLOCK) button. Pressing
this button will prevent anyone from making an OHVA to you until you press the
button again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (REJECT) button. Pressing
this button while receiving an OHVA call will disconnect the voice announcing
party and return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group, you can remove your keyset from
the group and then put it back in.While you are out of the group, you can receive
calls to your extension number but not calls to the group number. If you have an
IN/OUT button with the group number assigned.
•
•
Press the IN/OUT button. It will light red when your keyset is in the group.
Press the IN/OUT button again to exit the group and turn the light off. Repeat
as necessary.
If you do not have an IN/OUT button:
•
Dial the IN/OUT access code number ________________, then the group
number, then 0 to exit the group or 1 to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press SPEAKER button.
The IN/OUT button can include an extender to indicate the specific group that
this button will affect. This means that if you are in multiple groups, you can de-
cide for which groups you will receive calls.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME feature to enable password protection.
This will prevent unauthorized people from listening to your messages being left.
The passcode is the same as your station passcode. This feature only applies if
there is an SVMi card installed in the system and your keyset has a programmed
AME button.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 101 to turn on AME PASSCODE or 100 to turn it off.
Press TRANSFER to store your selection.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on, if possible, when
a busy station is called.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Press 081 to turn CAMP-ON on or 080 to turn it off.
Press TRANSFER to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
•
•
While on-hook, press TRANSFER and then dial 111.
Dial 1–8 or press the UP and DOWN buttons to hear each tone.
When you hear the tone that you prefer, press TRANSFER to save it.
NOTE: Specific lines or stations may be programmed to ring with a different
tone than what you have selected for your keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234.You can change your station pass-
code whenever you desire.
•
•
•
•
While on-hook, press TRANSFER and then dial 101.
Dial your old passcode.
Dial a new passcode (must be four characters).You can use 0–9.
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
Press TRANSFER to store the new passcode.
•
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes (see Answering Intercom Calls
under Intercom Calls for descriptions):
•
•
•
While on-hook, press TRANSFER and then dial 103.
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
Press TRANSFER to store your selection.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
•
•
•
While on-hook, press TRANSFER and then dial 110
Dial 15 to access AUTO ANS CO.
Press the VOLUME UP or DOWN key to change status.
Press TRANSFER to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line button, route button or a flashing CALL
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 001 to turn Automatic Hold on or 000 to turn it off.
Press TRANSFER to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing TRANSFER.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the FLASHING CALL button to answer and release calls.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 021 to use the headset or 020 to use the handset.
Press TRANSFER to store your selection.
Your keyset may be equipped with a Headset mode button. If it is so equipped
pressing this button while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the button while the
light is lit will cause the keyset to return to handset mode and the light will go out.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
HOT KEYPAD
On your phone system your keyset’s keypad can be made“live”or“hot”so that it is
not necessary to lift the handset or press the SPEAKER button before you begin
dialing. Calls can be made and features activated by simply dialing the C.O. line
number, trunk group access code, intercom number or feature access code. To ac-
tivate this feature:
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 031 to turn the Hot Keypad on or 030 to turn it off.
Press TRANSFER to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button on the
dial pad. This tone can be turned on or off.
•
•
•
While on-hook, press TRANSFER and then dial 110.
Dial 040 to turn tones off or 041 to turn tones on.
Press TRANSFER to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 051 to turn this feature on or 050 to turn it off.
Press TRANSFER to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset. This
method will always answer calls in the order they arrived at your keyset.When you
turn ring preference off, you must press the flashing button to answer a call, allow-
ing you to answer calls in the order you choose.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 061 to turn ring preference on or 060 to turn it off.
Press TRANSFER to store your selection.
AUTO ANSWER CO CALLS
This option will allow CO calls that directly ring your phone to auto answer. When
a CO call arrives at your station and this option set for ON your phone will sound
two beeps, the same as when a screened transfer is completed, and you will be
43
Download from Www.Somanuals.com. All Manuals Search And Download.
connected to the CO call. In order for this option to work the station must also be
programmed for auto answer (see SET ANSWER MODE).
•
•
•
While on hook, press TRANSFER and then dial 110.
Dial 151 to turn Auto Answer CO on or 150 to turn it off.
Press TRANSFER to store your selection.
NOTE: Outside lines must ring your station directly for the Auto Answer CO to
work. Lines ringing a station group will not cause your phone to Auto Answer.
DISPLAY SPEED DIAL NAME
This option allows you to view the name associated with a speed dial number as
it is dialed.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 111 to turn DISP SPDNAME on or 110 to turn it off.
Press TRANSFER to store your selection.
CALLER ID REVIEW ALL
This feature allows display keyset users to review Caller ID information for calls
sent to their stations.This list can be from ten to fifty calls in a first in,first out basis.
The list includes calls that you answered and calls that rang your station but that
you did not answer.When reviewing this list, you can press one button to dial the
person back. The system must be using LCR to dial the stored number.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 121 to turn CID REVIEW ALL on or 120 to turn it off.
Press TRANSFER to store your selection.
SECURE OHVA
This option allows you to receive OHVA calls via the speaker while you are on the
handset.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 131 to turn AUTO CAMP-ON on or 130 to turn it off.
Press TRANSFER to store your selection.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY FEATURES
INTERACTIVE DISPLAY KEYS
The three keys below the display are substitutes for dedicated feature keys and ac-
cess codes. Pressing one of these buttons has the same effect as pressing a pro-
grammable button. These buttons are called soft keys as their functions are not
fixed.They change to present you with the best options for that call condition.The
use of soft keys allows the programmable buttons to be used for more DSS and
speed dial buttons.
The SCROLL button is used to display options available to the user at a particular
time or during a specific procedure. Press this button once while in the idle state
to view the three main categories available.
201: STN NAME
CALL OTHER ANS
ANSWER: Guides you through the options to answer calls.
OTHER: Guides you through features other than making or answering calls.
CALL: Guides you through the options to make a call.
Select one of the main categories: CALL, OTHER or ANS (ANSWER). Press the
SCROLL button to display additional options available under each of the three
main categories.The symbol ¬ displayed as the last character on the lower line of
the display indicates that there are additional options. Press the SCROLL button to
display these additional options.
User instructions will be displayed in lower case letters. Options assigned to soft
keys will be in upper case letters.
DIRECTORY INFORMATION
An 11 character directory name can be assigned to each extension number.
Display keyset users can view the name of the called or calling station before an-
swering.
Each outside line can have an 11 character directory name. Incoming calls can be
easily identified and answered with different greetings.
Outside and internal calls ringing to a station group will display [CALL FOR xxx]
where xxx is the station group number.This allows you to answer calls directed to
you differently than calls directed to your group.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CALL LOG
The system can log both incoming and outgoing calls placed from or to your tele-
phone. You must have a LOG button programmed on your keyset and assigned a
review list.
Each IN and OUT list can be up to 50 numbers maximum. They are assigned in
blocks of 10 each.
•
•
•
Press the LOG key.
Press either the IN or OUT key.
View the first IN/OUT telephone number. At this point you may select one of
the three options related to this number or use the UP/DOWN keys to scroll
through your list of calls.
•
•
Press the CLEAR button to erase this number from the list.
Press the NND key repeatedly to view the Name, Number, or Date associated
with this call.
•
Press the DIAL key to call this number.
These options are the same for the incoming or outgoing call logs.
DIAL BY NAME
Each station or speed dial number can have an associated directory name. A sta-
tion or speed dial number can be selected by scrolling alphabetically through a
directory name list. This on-line “phone book” allows the user to look up and dial
any station or speed dial number in seconds.
•
•
Press the DIR button (DIRECTORY).
Select the directory you wish to use: PERS (personal speed dial numbers), SYS
(system speed dial numbers) or STN (station names).
Dial the key on the keypad that corresponds to the first letter of the name you
wish to search for.
•
•
•
Use the UP and DOWN arrows to scroll through the names.
Press the DIAL soft key to dial the number.
NOTE: A DIR button can have an extender to take you directly to one of the above
lists (PERS, SYS, or STN).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
CALL PROGRESS DISPLAYS
During everyday call handling, your keyset display will provide information that is
helpful and in some cases invaluable. Displays like [CALL FROM 203], [TRANSFER
TO 202], [701: RINGING], [TRANSFER FM 203], [708 busy], [Camp on to 204], [Recall
from 204], [Call for 501], [message frm 204] and [FWD ALL to 204] keep you in-
formed of what is happening and where you are. In some conditions you are
prompted to take an action and in other cases you receive directory information.
DISPLAY NUMBER DIALED
Display keysets begin showing digits as they are dialed. They will stay in the dis-
play until the call duration timer comes on automatically or the TIMER button is
pressed. If the call duration timer is not used, the number dialed will be displayed
until the call is released, transferred or put on hold.
CALL DURATION TIMER
The system can be set to automatically time outside calls. A few seconds after you
dial a telephone number, the timer appears in the display. It appears immediately
for incoming calls. The call timer continues for the duration of the call. Call dura-
tion times are displayed in minutes and seconds. If a call lasts longer than 60 min-
utes, the timer restarts.
You can press the TIMER button to manually begin timing a call. Press it again to
stop timing. If you press it while the automatic timer is on, the call duration time is
restarted.
AUTO TIMER
Display keyset users may have the timer automatically start when they answer
incoming calls or after a short delay on an outgoing call.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 011 to turn the auto timer on or 010 to turn it off.
Press TRANSFER to store your selection.
TIMER FUNCTION
Display keyset users may use this feature as a simple stopwatch.
•
•
•
•
When the keyset is idle, press the TIMER button to start timing.
Press the TIMER button again to stop timing.
Read the elapsed time in the display.
Lift the handset and replace it. The display will return to date and time.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
VIEWING MESSAGE INDICATIONS
You can view all of your message indications before you return them:
•
With the handset on-hook, press the MESSAGE button with the red flashing
light.
•
•
The first station that left a message indication will be displayed.
Press the UP and DOWN arrows to scroll through the stations that left mes-
sage indications. Use the soft keys to reply, clear or advance to the next mes-
sage.
ALARM REMINDER MESSAGES
(See also Special Application Menu-Name Search)
When you use the alarm/appointment reminder feature, you create a 16 charac-
ter reminder message. When the alarm rings, your message will appear instead of
[ALARM REMINDER]. To program reminder messages:
•
•
•
Press TRANSFER and then dial 116.
Dial the alarm number 1, 2 or 3.
Dial the time you want the alarm to go off.Enter the time as HHMM (hours and
minutes) using the 24 hour clock.
•
•
Dial 0 (NOT SET), 1 (TODAY) or 2 (DAILY) to select the alarm type.
Write your message using the dial pad keys. Each press of a key selects a char-
acter. Pressing the next key moves the cursor to the next position. For exam-
ple, if your message is “TAKE MEDICATION,” press 8 once to get the letter “T.”
Press 2 once to get “A.” Press 5 twice to get “K.” Continue selecting characters
from the following table to complete your message.
•
•
Press the TRANSFER button to store the alarm and reminder message.
Repeat for each alarm if needed.
COUNT
DIAL 0
DIAL 1
DIAL 2
DIAL 3
DIAL 4
DIAL 5
DIAL 6
1
2
>
?
3
.
4
)
5
0
1
2
3
4
5
6
<
space
,
!
A
D
G
J
B
E
C
F
I
@
#
$
%
^
H
K
N
L
O
M
48
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAL 7
DIAL 8
DIAL 9
DIAL ,
NOTES:
P
T
W
:
Q
U
X
=
R
V
Y
[
S
Q
Z
]
7
8
9
,
1. When the character you want appears on the same dial pad key as the previ-
ous character, press UP to move the cursor one space to the right.
2. Other symbols are available for DIAL #.
To cancel an individual alarm and reminder message:
•
•
•
•
Press TRANSFER and then dial 112.
Dial alarm number 1, 2 or 3.
Press the HOLD button.
Press the TRANSFER button.
PERSONAL SPEED DIAL NAMES
Each personal speed dial number can have an 11 character name assigned to it.
This name is used to select the speed dial bin when you are dialing by directory.
•
•
•
Press TRANSFER and then dial 106.
Dial the speed dial bin number 00–49.
Write your message using the procedure described in Alarm Reminder Mes-
sages.
•
•
Press the TRANSFER button to store the speed dial name.
Repeat for each speed dial bin if necessary.
STATION NAMES
You can assign an 11 character name to your keyset.This allows other display key-
set users to call you using the directory dial feature.
To program a station name:
•
•
Press TRANSFER and then dial 104.
Enter the 11 character name using the procedure described in Alarm Remind-
er Messages.
•
Press TRANSFER to store the name.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
MANAGING KEY ASSIGNMENTS
You can view your key assignments and add extenders to some of your program-
mable keys for easy one touch operation of frequently used features.
•
•
While on-hook, press TRANSFER and then dial 107.
Use the VOLUME buttons to scroll through all of your programmable buttons
OR press the programmable button to which you want to add the extender.
When you reach a key listed below, dial the corresponding extender.
Press TRANSFER to store and exit programming.
•
•
Please refer to the Enhanced Display Programming Section provided by your instal-
lation company when requested for a complete list of descriptions and extenders
for any keys you may have programmed on your keyset.
NOTE: Confirm that the cursor is placed correctly before you enter the extender.
LCR WITH CLEAR
When you are making an outside call using LCR and dial an incorrect digit, you can
press the CLEAR soft key to reenter the telephone number. You do not need to
redial 9 to reaccess LCR.
BACKSPACE WITH LCR
If you misdial while using LCR, you can delete digits shown in the display by press-
ing the BSPC soft key as many times as necessary.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TEXT MESSAGING
This feature allows two digital keyset users to respond to each other with prepro-
grammed text messages. After receiving an Off Hook Voice Announcement or
Station Camp-On, you may respond with a text message while continuing to talk
and listen to your outside party.The other station can view this message and take
the appropriate action or respond back with another text message.
You must be permitted to use the Text Messaging feature. See your System
Administrator or Technician to be assigned this feature. They will assign you ten
(10) blank messages.You can create any 16 character messages (01 to 10) that are
appropriate for your use.
NOTE: See ALARM REMINDER MESSAGES for instructions on how to enter charac-
ters to create a text message.
Familiarization with the two digit message numbers you will use the most will
make this procedure quick and easy. However if you do not know them, use the
UP/DOWN button to scroll to the desired message, then press SEND.
The basics steps in text messaging are:
1. Press TMSG soft key to begin text messaging.
2. Dial the 2 digit number for the desired message.
3. Confirm this is the intended message then press SEND.
4. Wait for a reply from the other station (steps 1, 2 & 3)
5. When any station presses EXIT the displays at both stations return to their
previous call progress condition.
At all times after step 1 you can talk and listen to your caller while repeating steps
2.
The following example will better demonstrate how to use Text Messaging. In this
example station 201 is making an off hook voice announcement to station 205
who after hearing the announcement will respond with a text message.
STATION 201: LINDA
STATION 205: JOHN
received a call on line 702
is talking on line 701
Talking on line 702
702:
01:15
701:
05:25
CONF PAGE MUTE
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Press TRANSFER
Transfer:
RETURN
Dial 205
205:busy
OHVA
CAMP ON
ꢀ
OHVA to 205
OHVA from 201
TMSG REJECT
Wait for reply
GIVE THE CALL
TMSG:01
SEND
Dial 03 or press ꢁ twice
ASK THEM TO HOLD
TMSG:03
SEND
ꢀ
ASK THEM TO HOLD
Wait for reply
TMSG
EXIT
ꢀ
702:
01:45
701:
05:55
CONF PAGE MUTE
CONF PAGE MUTE
52
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLER ID
WHAT IS CALLER ID?
Caller ID is the name given to the telephone company-provided feature that de-
livers the telephone number and sometimes the name of the person calling your
phone. There are two types of Caller ID; the first delivers the calling party’s tele-
phone number only and the second (sometimes referred to as “Deluxe” Caller ID)
delivers both the calling party’s telephone number and name as listed in the tele-
phone directory.
The phone system can handle both types of Caller ID; in fact, in the case of num-
ber only delivery, the system can be programmed to insert a name for a specific
telephone number. However, even though you are paying to receive Caller ID
information, there are some circumstances that mean you will not receive this in-
formation. The six most common reasons are listed below along with the display
information that the system will provide.
PRIVATE
The caller does not wish his/her name or number to be re-
vealed to you. This type of call can be stopped at the tele-
phone company by dialing an access code on your outside
lines. This will redirect these PRIVATE calls to an announce-
ment that states that you do not wish to receive calls that
have had Caller ID blocked.The code to block these calls can
usually be found in the front section of the telephone direc-
tory.
OUT OF AREA
PAYPHONE
The caller is calling from an area that cannot provide Caller
ID information (for example, international calls) or he/she is
calling from a type of circuit that cannot provide Caller ID
information, for example, some outbound WATS lines.
The caller is calling from a coin-operated telephone. The
telephone company will send this information as there are
no directory listings for pay phones.The number will be de-
livered as usual.
INVALID CID INFO
NO CID RECEIVED
This is a message that will be displayed when CID informa-
tion is sent on the line but was somehow corrupted.
This is a message that will be displayed when there was no
CID information sent on the line.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
NO CID DSP
Caller ID Digital Signal Processors (CIDDSP’s) are resources
in the OfficeServ 100, OfficeServ 500, and OfficeServ 7000
Series systems required for receiving CID data. If there are
no CIDDSP’s available at the time a call comes in, this is the
message you will see on your display.
NOTE:The Caller ID features require optional software and/or hardware.Please see
your service and installation company for details.
WHAT IS ANI?
ANI (Automatic Number Identification) is a feature offered by some telephone
service providers that provides the calling party’s telephone number. This service
is only available on E&M Tie Lines on a T1, digital trunk. ANI is similar to Caller
Identification (CID) but the format and information of the calling person is differ-
ent. CID uses FSK signalling and ANI uses DTMF signalling. Usually, with ANI, a call-
ing party’s identity is the Listed Directory Number (LDN) unless a separate bill-to-
number has been specified, (in which case the bill-to-number will be sent). Note
that ANI does not provide calling party NAME,only the number.The phone system
can provide calling number to name translation table.
WHAT IS CLI?
On ISDN circuits, calling party information is called CLI and is supported on both
BRI and PRI type circuits. On BRI circuits the system only supports number deliv-
ery and, like ANI, a name can be attached to the telephone number of frequent
callers via the Caller ID translation table. On 5ESS and NI2 PRI circuits both name
and number support is provided on the OfficeServ 100, OfficeServ 500, and
OfficeServ 7000 Series systems.
SELECTING YOUR CALLER ID
DISPLAY
You can decide if you want to see the Caller ID name or Caller ID number in the
display.Regardless of which one is selected,you can press the NND button to view
the other pieces of Caller ID information. To select the type of Caller ID informa-
tion you wish to view first:
•
•
•
With the handset on-hook, press TRANSFER and then dial 119.
Dial 0 for CID options, 1 for ANI options, or 2 for CLI options.
Dial 0 if you do not wish to view CID information, 1 to view the NUMBER first
or 2 to view the NAME first.
•
Press TRANSFER to exit and store your selection.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
VIEWING THE NEXT CALLER ID CALL
In the event that you have a call waiting or a camped-on call at your keyset, you
can press the NEXT button to display the Caller ID information associated with
the call in queue at your keyset. Either the CID name or CID number will show in
the display depending on your Name/Number selection.
To view Caller ID information for calls that have been camped-on to your keyset,
press the NEXT button. If your keyset does not have a NEXT button, press the CID
button and then the NEXT soft key.
SAVING THE CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may press
the SAVE button to save the CID number.If your keyset does not have a SAVE but-
ton, press the CID button, the SCROLL button and then the SAVE soft key.The sys-
tem must be using LCR to dial the saved number.
REDIALING A SAVED CALLER ID
NUMBER
To redial a number that has been saved, press the SNR button or dial 17.
NOTES:
1. Your telephone system must have LCR correctly programmed to redial the
saved number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
STORING A CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may save
the CID number as a speed dial number in your personal speed dial list.To store a
Caller ID number in a personal speed dial bin:
•
Press the STORE button. The system displays the speed dial bin in which the
number was stored, OR
•
•
•
Press the CID button and then press the SCROLL button.
Press the STORE soft key.
The system displays the speed dial bin in which the number was stored.
NOTE: Your telephone system must have LCR correctly programmed to redial the
saved number. If LCR is not being used on your system, you will not be allowed to
STORE CID numbers.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
INQUIRE CALLER ID PARK/HOLD INFO
If you are informed that an incoming call is on hold or has been parked for you,
you may view the Caller ID information before you retrieve the call.This may influ-
ence how you choose to handle the call.
From an idle keyset:
•
Press the INQUIRE button, OR
Press the CID button and then the INQUIRE soft key.
Dial the trunk number.
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
•
•
If you are on a call:
•
Press the INQUIRE button.Your existing call will go on hold, OR
Press the CID button and then the INQUIRE soft key to place the first call on
hold.
•
•
Dial the trunk number.
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
NOTES:
1. If you are on an intercom call or you have Automatic Hold turned off, you
must finish the existing call or place it on hold before inquiring.
2. If you inquire about an outgoing call, you will receive a [call no longer avail-
able] display.
REVIEWING PAST CALLER ID CALLS
This feature allows you to review CID information for calls sent to your keyset.This
list can contain 10–50 calls in a last-in,first-out basis.The list includes calls that you
answered and calls that rang your keyset but that you did not answer. When
reviewing this list, you can press one button to dial the person back. The system
must be using LCR to dial the stored number.To access the CID information stored
in your REVIEW list:
•
Press the REVIEW button, OR
Press the CID button and then press the REVIEW button.
If you have entries in your review list, the most recent call will be shown first.
You can now CLEAR this entry, OR
•
•
Use NND to view more information about this call, OR
Press DIAL to call this person back, OR
Press SCROLL and then press STORE to save this number in a personal speed
dial bin.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
1. Each keyset defaults with ten review bins. Please see your system administra-
tor to determine the number of bins assigned to your keyset.
2. Your system must have LCR correctly programmed to allow you to DIAL num-
bers from the review list or to STORE entries from the review list.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
SVMi E-Series
This section describes how to setup and use the various features available to a
Subscriber. A Subscriber is a person that has been authorized access to the vari-
ous features and services available in the SVMi E-Series. Please review this section
carefully before you use your Authorized Features and Services, known as
Subscriber Services.
Voice Mail is one of the Subscriber Services available. Your voice mail box has the
capability of storing private messages, and offers a number of options for sending
or redirecting messages as well as provides several ways to notify you of new mes-
sages.
Another very common Subscriber Service is Access Manager.This allows you con-
trol over when and where you receive your calls as well as what to speak to your
callers in the event you are unable to speak to them directly. The ‘events’ are
referred to as “Call Conditions”. No-Answer, Busy, and Blocked are the most com-
monly used Call Conditions.
This guide can be used by Subscribers from within the office or from telephones
outside the office. The basic operation is the same, but the access method will be
different. See the SVMi E-Series Subscriber Services Menu Diagram for more
details.
Note that some features and prompts detailed here may not be available to all
Subscribers. See your System Administrator if you have questions about feature
availability.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSING YOUR MAILBOX
[Also known as Subscriber Services Menu]
Inside Callers [Subscriber logging in from their Desk]
•
Dial the SVMi E-Series access number or press the key assigned to ring
SVMi E-Series [VMMSG].
•
Enter your personal password when prompted (the default password is
0000).
Outside Callers [Subscribers calling from Cell Phones or outside of the
office environment]
•
•
•
Dial the phone number that will be answered by the SVMi E-Series.The main
greeting will answer.
At the main greeting dial [#] plus your Subscriber (or mailbox) number
(Subscriber and Mailbox numbers will usually match your extension number).
Enter your personal password when prompted (the default password is
0000).
Access your Subscriber Services (or Mailbox) from a Station
other than your Own (or checking a mailbox associated with a
different station)
•
Press the [VMMSG] key or dial the SVMi E-Series group number. You will be
prompted to enter a password.
•
•
Press [,]. This will take you to the Main Auto Attendant Menu.
Press [#] plus the Subscriber number of your choice.You will be prompted to
enter you password.
At this point the inside and outside callers follow the same instructions. You will
hear a message stating the number of messages left in your mailbox.You will then
hear the Subscriber Services Menu with the following options:
1
2
3
4
5
6
#
,
Listen to New Messages - See Listening to your Message.
Record and Send Message - See Sending Messages.
Review Saved Messages - See Listening to your Message.
Access Manager - See Access Manager.
Personal Greetings - See Personal Greetings.
Mailbox Administration - See Mailbox Administration.
Personal Services - See Personal Services.
Return to Main Menu.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
SVMi E-Series Subscriber Services Menu
r
NOTE: All options shown MAY NOT be authorized. If an option is not available
please speak to your system administrator.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Using your new SVMi E-Series Subscriber Services is as simple as following a few
simple spoken instructions. First time users should read this section as a tutorial.
You should start with the following steps:
•
Access your Subscriber Services Menu - You already know how to do this.
From the Subscriber Services Menu:
•
•
•
•
•
Record a Primary/No-Answer Personal Greeting. Dial [5][1].
Record a Mailbox Greeting. Dial [5][7].
Change your access code (Password). Dial [#][7][1].
Record your name. Dial [#][7][2].
Enter your directory name. Dial [#][7][3].
After you have completed the steps above your Subscriber Services are set up and
ready to use.
LISTEN TO YOUR MESSAGES
If there are new messages in your mailbox your [VMMSG] key will be lit. Call the
SVMi E-Series by pressing this key, and when prompted enter your password.You
will then be at the Subscriber Services Menu. Select [1] to listen to new messages
or [3] to listen to saved messages.
Note:After you enter your password, if“Autoplay of New Messages”is enabled and
you have new messages the SVMi E-Series will begin to play them automatically.
A subscriber can control this feature. From the Subscriber Services Menu [6] [5]
toggles “Autoplay of New Messages” ON/OFF.
SUBSCRIBER SERVICES MENU
The following is a list of all the options available in the Subscriber Main Menu.
1
LISTENING TO NEW MESSAGES
GROUP NEW MESSAGES
RECORD AND SEND A MESSAGE
LISTENING TO OLD MESSAGES
GROUP OLD MESSAGES
ACCESS MANAGER
11
2
3
33
4
5
PERSONAL GREETINGS
6
MAILBOX ADMINISTRATION
PAUSE / RESUME
8
62
Download from Www.Somanuals.com. All Manuals Search And Download.
0
,
#
PLAY MENU OPTIONS
EXIT TO AUTO ATTENDANT
PERSONAL SERVICES
1 or 3
LISTENING TO OLD OR NEW MESSAGES
1
Play / replay the message you just heard.
Play the previous message.
11
2
Save the message you just heard and listen to the next message.
Delete the message you just heard and listen to the next message.
Reply to the message.
3
4
This will allow you to leave a message in the mailbox of the sender (if the
sender has a mailbox on this system).
5
Return the call directly to the telephone number that left the message.
This will work for internal and external callers, but Caller ID service is need-
ed to use this feature on an outside call.
55
Deliver a fax copy.
This will allow you to receive attached faxmail document(s). Faxmail docu-
ments can be delivered to any fax machine of your choice as long as out
calling is authorized. You can also have faxmail messages automatically
delivered to the fax machine of your choice.
6
Forward the message and saves a copy.
The subscriber can be selected by dialing their mailbox number (nnn),
using the directory service (#) or you may also add comments and leave it
as a memo to yourself (##).
The Send and Copy Service (option 6) allows a user to send copies of a mes-
sage to multiple recipients easily. A different introduction message may be
left for each recipient.
7
Rewind the message 5 seconds.
77
Change playback volume of the recording.
There are two levels of volume during playback. Dialing this code will tog-
gle between the two levels.
8
9
Pause or resume during message playback.
Fast forward the message 5 seconds.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
99
0
Change playback speed of the recording.
There are two levels of speed during playback. Dialing this code will toggle
between the two speeds.
Play options.
Pressing this key will play all the menu options available to you from this
point.
00
#
Hear the time and date, and sender's information of the message you just
heard. Sender information is not available on outside calls.
Move to the next message. This does not Save or Discard the current mes-
sage - it is retained as new.
##
Scan. Plays first 7 seconds of a message then skips to next message. This is
similar to the scan button on a radio. It will allow you to find a specific mes-
sage quickly. To stop scanning press [1].
,
Cancel and return to previous menu.
11 or 33
GROUP NEW OR OLD MESSAGES
Messages can be grouped as either Reminders, press [3] or Messages from a spe-
cific sender, press [9].
Additionally you can press [#] and hear a summary of your mailbox contents:
a) Number of messages
b) Number of reminders
c) Number of urgent messages
d) Number of messages needing a callback
e) Number of private messages
f) Number of fax messages
2
RECORD AND SEND A MESSAGE
This option is used to send a message to another subscriber.The steps are simple:
a) Enter the recipient’s mailbox number, or if this is not known enter [#] to use
the system directory.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
b) Record your message at the tone. After recording the message, you will hear
the Send Menu with the following functions:
1
2
3
4
5
6
#
Review
Continue Recording
Discard and Re-Record
Set Message Attributes (Delivery Options)
Schedule Future Delivery
Save and Send then Send a Copy to Someone Else
Save and Send the Recording
Setting Message Attributes
If after recording a message you select [4] you can set up any combination of the
following delivery options:
1
2
3
4
5
,
Urgent Delivery
Return Receipt Requested
Request a Call Back
Private Delivery
Reply Required
Exit
Scheduling Future Delivery
If after recording a message you select [5] to schedule future delivery, you will be
able to set message attributes and set this message as:
#
1
2
3
4
5
,
Immediate Delivery
Next Few Hours
End of Current Business Day (based on your Availability Schedule)
Beginning of Next Business Day (based on your Availability Schedule)
A Coming Day of the Week
Specific Day / Time
Exit
4
ACCESS MANAGER
The Access Manager allows the subscriber to set a number of options for when,
where and how, and/or if the SVMi E-Series contacts you when a caller dials your
extension number.All of the options are toggled on/off based on their current sta-
tus when you access them.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: ALL Access Manager options MUST be individually allowed by the System
Administrator for each Subscriber. They are:
1
Follow Me
Allows the subscriber to enter an alternate location and set how long the new
destination (Designated Location) will be active. This number may be an
internal or external number. This is useful if you are frequently traveling or
changing the number where you can be reached.
When Follow Me is activated, the transfer will be supervised and confirmed.
This means that if the call is not answered or if rejected by the Subscriber at
the designated location it will be recalled to the Subscriber’s mailbox.
3
4
Call Blocking
When this feature is active, callers will not be transferred to your extension,
they will hear your 'blocked' greeting (if recorded) and will go directly to your
mailbox if they do not select any or are not offered any other options.
Call Forwarding
Unlike Follow Me where the subscriber wants to take their calls at an alter-
nate location this feature allows the subscriber to pass control of his calls to
another Subscriber. The “Forwarded To” Subscriber will now be in control of
the caller and the caller will NOT return to originating Subscriber’s Mailbox. If
the “Forwarded To” Subscriber does not answer the caller it will now follow
what ever the “Forwarded To” Subscriber has set up for their call conditions.
The Caller will hear“Forwarding to”“{Subscriber Name}”before actually being
forwarded.
5
6
Call Screening
If this is turned on, the caller will be asked their name and the SVMi E-Series
will play this name to you before the transfer, giving you an option to accept
or reject the call.
Find Me
Find Me, when enabled, will attempt to locate the subscriber by calling a list
of preprogrammed phone numbers. The stored phone numbers are entered
in 'Personal Services' [#][2] (if allowed by the Administrator). The stored tele-
phone number list can contain up to 9 preprogrammed telephone numbers.
The Find Me feature only use the first five.
7
Night Intercept
This feature is dependent on your weekly availability schedule, which is
entered in 'Personal Services' [#][3] (if allowed by the Administrator). When
Night Intercept is active the SVMi E-Series will first ring your extension then
66
Download from Www.Somanuals.com. All Manuals Search And Download.
play your primary, No Answer greeting during the day (when you are avail-
able) and will NOT ring your extension but simply play your Night greeting
during the night (when you are not available).
Note: This does NOT use the Day and Night schedules of the phone system. It
is solely controlled by the Subscriber’s Availability Schedule.
8
,
0
#
Pause / Resume
Exit from Access Manager
Play All Options
Play Access Coverage
This feature is useful for finding out how you current access settings are set.
It will also tell you what greetings will play under each of the call conditions
you have setup.
5
PERSONAL GREETINGS
The options available in this menu will be determined by your System
Administrator, and not all of them may be available to you. In the simplest sys-
tems, only a mailbox greeting will be available, additional greetings may be acces-
sible in more complex systems.
Your Personal Greeting will be played every time someone dials your extension
and you do not answer.
You may record up to 9 Personal Greetings, and you may assign any one of them
to be active. There are several different 'Call Coverage' conditions to which you
may assign any of your 9 greetings.The Call Coverage Conditions are: No-Answer,
Busy, and Do Not Disturb (or Forwarded All). This will allow different greetings to
play depending on the type of call forward that you have set, or the condition of
your telephone.
The Call Coverage conditions that you can assign specific greetings to are select-
ed by the following digits:
1
Primary/No Answer Greeting
Used when in your office, away from your desk or during the time period you
are scheduled available. If this is the only Personal Greeting you record, it will
play for all call coverage conditions.
This option is available only if the Administrator has assigned you the 'Basic
Greeting' feature.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Example:“Hi this is John Smith.I'm sorry I am not available to answer your call.
If someone else can help you, please enter the extension number now. Or, to
leave me a message, press 1.”
2
Busy Greeting
Played to a caller when you are already talking to someone on your extension
or the telephone at your Designated Location.
This option is available only if the Administrator has assigned you the 'Busy
Greeting' feature.
Example:“Hi, this is John Smith. I'm on another line right now. If someone else
can help you, please enter the extension number now. Or, to leave a message,
press 1.”
3
Call Blocking Greeting
Used while Call Blocking is enabled in your Access Manager or if your phone
is forwarded ALL or DND.
This option is available only if the Administrator has assigned you the 'Call
Blocking' feature.
Example:“Hi, this is John Smith. Sorry I missed your call, but I'm going to be
out of the office for the next few hours. If someone else can help you, please
enter the extension number now. Or, to leave me a message, press 1.”
4
Night Greeting
Used during the time period you are scheduled UNAVAILABLE, usually after
business hours during the evening and at night.
This option is available only if the Administrator has assigned you the
'Scheduling' feature.
Example:“Hi, this is John Smith. I've left the office for the evening. If you would
like to try someone else, please enter the extension number now. Or, to leave
me a message, press 1.”
5
Call Screening Greeting
Used while Call Screening is enabled, and you REJECT a caller after listening
to the caller's record name.
This option is available only if the Administrator has assigned you the 'Call
Screening' feature.
Example:“Hi, this is John Smith. I'm sorry, but I am not available to speak with
you at this time. If someone else can help you, please enter the extension
number now. Or, to leave me a message, press 1.”
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Edit Personal Greetings
You may also edit/record each one of the greetings (1-9) at any time.
Select a greeting number to edit and follow the instructions to record your
greeting. When you are done recording your greeting, you will be able to lis-
ten to the greeting you recorded, save the greeting you recorded and return
to the previous menu, record the greeting again, or exit without saving the
greeting.
Note: If you record only the greeting assigned to the No-Answer Call
Coverage Condition,then that greeting will play to callers for all Call Coverage
Conditions (No-Answer, Busy, Blocked, Night, and Rejected Caller). In this case,
the salutation part of the greeting should be very general.
7
Edit Mailbox Greeting
Used whenever a caller reaches your mailbox or if you have not recorded any
of the Call Coverage greetings.The way a caller is transferred to your mailbox
greeting directly, is by another subscriber transferring the caller to your mail-
box using the VT (VoiceMail Transfer) key.
This option is available only if the Administrator has assigned you the
'Mailbox Greeting Option' feature.
Example:“Hi, this is John Smith. Please leave me a message, I will call you as
soon as I can.”
Note: This greeting will only play if none of the 5 personal greetings has
played to the caller. A common usage for this Greeting is when another
Subscriber is talking with a caller and uses the VT key on their phone to trans-
fer the caller directly to your Mailbox.
6
MAILBOX ADMINISTRATION
The Mailbox Administration menu is used to turn on and off your pager notifica-
tion, message alert options and other message control features.
1
Message Alert
When this function is activated, the SVMi E-Series will call any outside or
inside telephone number, after each message is left in your voice mailbox.
To hear your message at the remote location when the SVMi E-Series calls
you, after you pick up the telephone and answer you will be instructed that
there is a message and to enter your password. Simply enter your password
and you will now be logged in.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Message Alert:
■
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [1] for Message Alert.
There are 4 options available to you:
Press [1] to toggle message alert on and off.
Press [2] to set the schedule when you would like to be notified.
Press [3] to be notified on urgent messages only.
Press [4] to set the destination phone number.
2
Pager Notification
When this function is activated, the SVMi E-Series will call your beeper service
and notify you after each message is left in your voice mailbox.
■
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [2] for pager notification.
There are 4 options available to you:
Press [1] to toggle pager notification on and off.
Press [2] to set the schedule when you would like to be paged.
Press [3] to be notified on urgent messages only.
Press [4] to set the pager phone number.
3
Undelete
When this function is activated, the SVMi E-Series will allow you to undelete
any messages that you have recently deleted (up to the programmed Daily
Maintenance Time, which is set to 3 a.m. by Default the following morning).
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [3] for Deleted Messages.
Deleted voice mail messages are temporarily stored in memory until 3 a.m.
the following day. Select this option to recover ("undelete") previously delet-
ed messages, during this period of time.
4
Undelivered Retrieval
When this function is activated, the SVMi E-Series will allow you to recall any
messages you have sent that have NOT yet been picked up by the recipient.
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [4] for Undelivered Messages.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
This useful feature will allow you to cancel any messages that have NOT yet
been picked up by the recipient.
5
6
Auto Play New Messages
If this option is enabled, after you enter your password correctly any new
messages will immediately begin to play.To enable (or if already enabled tog-
gle and disable) this feature:
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [5] to Set Auto Play of New Messages.
Auto Play Message Information
If this option is enabled, the date, time and sender’s name will be played auto-
matically before each message. If this is disabled, the information must be
requested manually by pressing ‘00’. To enable (or if already enabled toggle
and disable) this feature:
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [6] to Set Auto Play of Message Information.
9
MESSAGE BROADCAST
This option will only be available if it has been allowed by the System
Administrator.
Broadcast to All Mailboxes
If you have been designated as a Subscriber Administrator, you may send a
message to ALL mailboxes in the system.
■
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [9] for Broadcast Messages.
This option will only be available if your mailbox has been assigned
Subscriber Administration privileges.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
#
PERSONAL SERVICES
The Personal Administration Menu is used to set your password and record your
name. Many of these features must be allowed by the System Administrator.
1
Workload Management
Allows you to access to all reminders, both Active and Pending. If authorized
you can group your reminders as Commitments, Follow-Ups or Tasks for bet-
ter organization. The system will flag each reminder as Active or Pending
(pending means scheduled for future delivery).
2
Stored Numbers
Allows you to enter up to 9 stored phone numbers. The first five of these are
used in the 'Find Me' feature, but any of them (1-9) can be easily dialed using
only one digit followed by the pound key, to be used by many other features
from within your subscriber space. (ie: “Follow Me, “Message Alert”, “Pager
Alert”, and “Direct Call”).
3
5
Schedule Availability
Allows you to enter a weekly availability schedule for use with Night Personal
Greeting and the Auto Night Intercept feature. Follow the spoken directions
to enter the days of the week and times you are generally available to talk to
your callers. All other times you will be considered unavailable.
Place a Direct Call
Allows you to place a direct call out of the SVMi E-Series from anywhere. You
may either dial the number or dial a single digit 1-5 that corresponds to a
stored number (See Personal Services, 2 - Stored Numbers).This feature must
be authorized by the System Administrator and can be limited or opened to
internal, local, and long distance calls.
7
Personal Administration
This area is used during the initial set up of your Subscriber Settings (see next
section).
72
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL ADMINISTRATION SETTINGS
This menu allows you to make changes to basic setup settings, that are rarely
changed. Use these when you initially set up your personal Subscriber settings.
You probably will not need to change them after that.
1
Setting your Password
■
■
From the Subscriber Services Menu press [#][7][1].
The current password will be played and you will have the chance to
change it.
2
Recording your Name
Use this option to record your name.Your recorded name is played in several
different situations. It is important to record your name for proper operation
of the SVMi E-Series system.
■
■
From the Subscriber Services Menu press [#][7][2].
The current name will be played and you will have the chance to change
it.
Note: It is possible that if you do not record your name and/or enter your
Directory Name (described below), you will not be included in the Dial by
Name Directory.
3
Entering your Directory Name
Use this option to enter your Directory Name.Your Directory Name is used by
callers to find you if they do not know your extension number.
■
■
From the Subscriber Services Menu press [#][7][3].
The current Directory Name will be played as a string of digits that are
equal to your name spelled out on your telephone keypad. Follow the
instructions to enter a new name.You will be prompted to enter your last
name and then your first name.
This must be done in order for the directory feature to work correctly.
Note: It is possible that if you do not record your name (described above)
and/or enter your Directory Name, you will not be included in the Dial by
Name Directory.
4
Extended Prompting
Use this option to drastically reduce the number of prompts played in the
subscriber interface (mailbox prompts). Change this setting only if you are
very familiar with the user operation of the SVMi E-Series.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Remember if you know what digits to press, you can enter them at any
time you do not have to wait to be prompted. This feature can be toggled
on/off at anytime. Also if it is off you will be prompted within each subscriber
menu to press zero for more options. This enables you to still be able to find
out what to do if you were to get lost and extended prompting was disabled.
KEYSET USER FEATURES
The following options are available if you have a display keyset.They require setup
by the System Administrator.
Message Waiting Lights
When new messages are left in your mailbox,the voice mail message light on your
keyset will flash. Press this flashing key [VMMSG] and follow the prompts to
retrieve messages.This key may be pressed at any time to log into your Subscriber
Main Menu.
Answer Machine Emulation
If you have an Answer Machine Emulation key programmed on your keyset, you
can use it to monitor calls going to your voice mail, and optionally answer them.
The operation of this feature is similar to screening a call on a home answering
machine.
Your keyset must be set to forward on no answer to voice mail. After ringing your
station the caller will be connected to your voice mail and hear your personal
greeting before leaving a message. During this time you will be monitoring the
connection between the caller and your voice mail box. At this time you will only
be monitoring the call, you can not talk to the other party until you answer. You
may pick up the call at any time or ignore it.
To activate this feature press the AME button. The associated indicator will be lit
steady. Press again to turn off. If this key is pressed while a station is ringing (dur-
ing forward no answer), the feature will be turned on for the current call only.
While the caller is leaving a message or ringing you may:
■
■
Press [#] to immediately put the caller in your voice mailbox and monitor it.
Press [,] to immediately disconnect your station. The caller continues to
leave a message normally.
■
Pick up the handset and monitor privately.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
AME Password
If your keyset has AME PASSWORD (MMC 110) set to YES, you must enter your
station password to listen to messages being left. This will prevent unauthorized
people from listening to messages being left for you.
If the password option is turned on, while a message is being left, press the flash-
ing AME indicator and enter your station password (not your SVMi E-Series pass-
word).You will then hear the message being left.
Call Record
If you have a call record button assigned to your phone, you may press it at any
time, to record the conversation in progress. If you have a display keyset, you will
also have the soft key options to pause and time the message.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
SHORTCUTS
Calling
Calling a station that is busy or does not answer you can press [#] to immediately
send the call to the called parties mailbox.
Call Divert to Voicemail
While receiving an incoming (ringing) call, dial [,] to immediately send the caller
to your personal voicemail box. This will override the call forward no answer set-
ting.
Direct Messaging
[#] + DSS To make it easy to leave messages for others in your office without hav-
ing to dial their extension number first, keyset users may simply dial [#] plus a
mailbox (extension) number and leave a message directly.If you dial a busy exten-
sion press [#] to connect directly with the mailbox.
Self Memo (Reminder)
Pressing [##] will leave a message in your own mailbox. This is useful to remind
yourself of things to do now or in the future. Messages can be sent with future
delivery so you can have the system call you when items become due.
INTERACTIVE DISPLAYS
Display keyset users have the added advantage of using the soft keys and displays
to play, save, delete, reply, call, forward, rewind, pause, fast forward, change the vol-
ume, get message information, or help.
Viewing Mailbox Contents
If you have new messages, in addition to the Terminal Status Indicator (TSI) you
will be able to use the keyset displays and soft keys to communicate with the
SVMi E-Series.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SPEED DIAL NUMBERS
CODE
NAME
TELEPHONE NUMBER
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
77
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SPEED DIAL NUMBERS
CODE
NAME
TELEPHONE NUMBER
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
78
Download from Www.Somanuals.com. All Manuals Search And Download.
System Feature Codes
Line Groups
Local/LCR
Feature Access Codes
9
10 + xxx
12 + xxx
13
16 + xxx
17
Pick Up A Parked Call
800 ____________________________
801 ____________________________
802 ____________________________
Pick Up A Held Call
Door Lock Release
Speed Dialing
Save And Redial Number
New Call (Recall)
Station Groups
18
19
400
401
42 + xxx
43
Last Number Redial
Cancel Do Not Disturb
Set Do Not Disturb
Cancel Message Wait
Return Message
501 _____________________________
502 _____________________________
503 _____________________________
504 _____________________________
44
45
46
47
48 + xx
49
53 + xxx
54
56
600
601 + xxx
602 + xxx
603 + xxx
604 + xxx
605 + xxx
606 + xxx
65 + xxx
66 + xx
67
Callback
Busy Station Camp-On
Conference
Paging Zones - Dial 55 plus
0
1
2
3
4
5
6
7
8
9
*
All Internal Zones
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
_____________________________
All External Zones
Account Code
Programmed Messages
Send Flash To C.O. or PBX
In/Out of Group
Meet Me Page
Meet Me Page Answer
Cancel All Call Forward
Set Forward All Calls
Set Forward Busy
Set Forward No Answer
Set Fwd Busy/No Answer
Set Forward on DND
Set Forward Follow Me
Pick Up Ringing Extension
Group Call Pick Up
Universal Answer
All External Zones and Internal Zone 0
Programmed Messages - Dial 48 plus
00 Cancel Message
01 In A Meeting
02 Out On A Call
03 Out To Lunch
04 Leave A Message
05 Page Me
*
Authorization Code
06 Out Of Town
07 In Tomorrow
08 Return Afternoon
09 On Vacation
10 Gone Home
11 _____________________________
12 _____________________________
13 _____________________________
14 _____________________________
15 _____________________________
16 _____________________________
17 _____________________________
18 _____________________________
19 _____________________________
20 _____________________________
ITP-5107S KUG 01 05/06
w w w . s a m s u n g . c o m / b c s
Download from Www.Somanuals.com. All Manuals Search And Download.
|