SCC-B5397
SCC-B5399
DIGITAL COLOR DOME
CAMERA
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
1. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
2. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify
this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or
attempted repair.)
S
3. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to
excessive vibrationor magnetic interference.
nt
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high
humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or
damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
er
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
WARNING
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
13.Unplug this apparatus when a card is used. Use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
4 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction
Features
Product & Accessories
Part Names and Functions
6
7
8
Installation
Before installation
Installation procedure
Adjusting the camera direction
11
11
12
How to use OSD Menu
Using Icons in the Menu
Main Menu
14
14
15
17
24
27
28
29
29
e
Profile
Camera Setup
Intelligence
nd
Privacy Zone Setup
Other Set
System Information
Language
Specifications
Specifications
30
ve
or
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
FEATURES
C
❖
❖
❖
❖
❖
High Resolution
•
This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm
technologies.
VPS(Virtual Progressive Scan)
•
This is an advanced technology that reproduces a sharp progressive image. This is appropriate to high quality recording and file
transfer via the Internet.
Intelligent Motion Detection & Tracking
•
This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it displays an alert if an object
passes / enters /exits the virtual fence or virtual area.
WDR
WDR extends the contrast range as it takes a picture of each of dark and bright areas before compositing the two, which is useful if
you take a picture of windows inside a building. Namely, it improves the picture quality of the outdoor scenery as well as indoor.
XDR (eXtended Dynamic Range)
•
•
Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine
the optimal visibility.
❖
❖
❖
DAY/NIGHT
This function can make the IR Cut filtering function inactive under the illumination below the normal value.
High Sensitivity
It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.
Low Illumination
•
•
•
It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify objects even in the
worst environment.
❖
❖
Superior Backlight Adjustment
When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality.
Digital Power Synchronization
•
•
The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operationability and reliability of
this camera.
❖
Output Signal Setting
•
You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling,
and digital zooming.
❖
❖
OSD(On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the functions interactively.
Coaxial Cable Communication
•
•
This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the control signal. In installation or repair, this
helps you control the communication controller (optional) without additional cabling.
6 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Components
Checking components in the package
Camera
Test Monitor Cable
User’s Guide
f
e
Image
Part name
Standard
Quantity
4 (EA)
8
Usage
Attach each piece to screw connection holes for
strengthening connection
Plastic anchor
HUD 5
BH M5 X L6.
(White+o-ring)
ASSY screw
machine
Used for filling in the holes when installing
pipe and wall mount
TH M4xL30 (Black+
o-ring)
ASSY screw
tapping
Used when installing your camera on the
4
1
ceiling or wall。
f
Used for assembling/disassembling the
Dome cover
L-Wrench
TROX T-20
Template
1
1
Used for guiding the installation
Used to make a wiring hole when installing
the camera on the ceiling or wall
Gasket-pipe hole
T2.5 W56
–
NOTE
The test monitor cable is used to test the camera by connecting to a portable display. If you
really want to connect the camera to a monitoring display, use the BNC cable.
s
–
。
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Dome cover: Covers the inner cover, lens, and
1.
Components of your camera
❖
main body to protect them.
Your camera has the following components:
Cover screw: Use it to assemble or
2.
disassemble both dome cover and case.
Inner cover: Covers the main body to protect it.
3.
1
3
.Wing locker: Push a long thin screwdriver into
4
its narrow spot and press it outward when you want
to remove the inner cover.
Main body: Includes a lens, a switch board, a
5.
PCB board, screws, and such.
2
4
5
Screws for assembly and disassembly: Using
6.
these 2 screws, the Main
7
body is closely connected to the Case.
6
6
Hooker: By pulling the left/right levers in the
7.
arrow direction, the Main body can be detached
from the Case.
7
Case: Used as a ceiling or wall fixture. It is
8.
8
fixed using four screws provided in the package.
Zoom lever: Using this lever, the lens zoom can
9.
be adjusted and fixed.
Focus lever: Using this lever, the lens focus can
10.
be adjusted and fixed.
Lens
•
Tilt fixing screw: Using this screw, the slope of
11.
the lens can be adjusted and fixed.
Cable: Connect the Video connector to BNC
12.
cable and Power connector to power adapter.
9
10
11
12
Video connector
Power connector
8 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
❖ Setting switches
•
SETUP Switch
This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the
MAIN MENU appears.
ef (Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the
displayed value.
cd (Up/Down) : By pressing this switch up or down, you can move up or down on the menu.
ꢀ: When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press
this button.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
I
Be
ar
Installing camera
Before installation
To
1.
Before installing your camera, you have to read the following cautions:
ꢁ
ꢁ
You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may
cause a breakdown or fire. You can use wall mount adaptor (SADT-102WM), and pole mount adaptor (SADT-
100PM) for installing the camera on the wall or pipeline.
ꢁ
When installing your camera, don’t allow any person to approach the installation site. If you have any valuable
em away.
things under the place, move th
About the installation holes
A:Use these holes when directly installing your camera on the ceiling or
wall.
ꢂ
While those are not used, fill in the holes using the screw machine (M5
X L6.) for waterproofing.
Bottom of camera
B: Use four holes when directly installing your camera on the junction box
ꢂ
You can use the 4 1/8 diameter round type junction box for assembly.
(The junction box, gasket, and cover are separately purchased items.)
2.
A
B
C: Use these holes when installing the wall mount adapter (SADT-
102WM)
ꢂ
While those are not used, fill in the holes using the screw machine (M5
for waterproofing.
X L6.)
The holes that are not used should be tightly
C
sealed up using the screws provided for
waterproofing. When the screws don’t have rubber
rings inside or are not closely attached, note that it
can cause waterproofing problem.
F o r a t t a c h i n g s c r e w s , s e e p a g e 1 6
“Disassembling/assembling the Main body from
the Case.”
10 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
n
Installation
Installing on a pipe
Before installation, you have to be familiar with the above cautions and fill in the holes that
are not used for installation.
To install your camera bottom on a pipe
3. Attach the Dome cover. (Screw the connection bolts
tightly using the L-Wrench for waterproofing.)
1.
After connecting the power and video cables,
ꢂ
To change the SAMSUNG logo position, move the
location of the connection rubber band as show
below and rotate for assembly. (The rotation limit
is 180 degree.)
throw them inside the pipeline and screw the male
thread pipe into the female pipe thread in your
camera tightly to fix the Main body. (In this case,
be sure to tape with Teflon tape before assembly for
waterproofing. Be careful for the wiring cable not to
be stuck in the connection area.)
2. Adjust the angle of the camera in search of a better
view.
1) Separate the Dome cover using the L-Wrench
provided. (To make loose the screws, rotate
counterclockwise.)
2) Adjust the lens direction. For more information,
see page 17 “Adjusting the camera direction.”
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
When the camera is fixed on the ceiling, you can adjust the camera viewing angle.
You can rotate your camera leftward or rightward (Panning), and can change the
slope of your camera upward or downward (Tilting).
H
Adjusting the camera direction
U
•
In case of panning, the rotation limit of your camera is set to 355 degree (100
degree clockwise and 255 degree counterclockwise). The rotation is stopped by
the Stopper inside of the camera. For panning control, first unfasten two screws
located on the bottom and rotate in the direction you want, and then fasten them to
fix the camera.
•
•
In case of tilting, you can change the slope of your camera from zero to 90 degree.
However if the slope angle is under 17 degree, you can encounter a partial image
hide problem. To fix the location after adjusting the tilting angle, use the Tilt fixing
screws.
•
To adjust the focus and zoom of your camera, use the Zoom lever and Focus
lever. When you install the camera on the inclined ceiling or wall, you can rotate the
camera lens to see a correct direction image.
Panning
•
Tilting
Lens rotation
12 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
USING ICONS IN THE MENU
MAIN MENU
e.
e
•
ꢀ (EXIT)
ꢃꢃMAIN MENUꢃꢃ
PROFILE
CAMERA SETꢅ
INTELLIGENCEꢅ
PRIVACY ZONEꢅ
OTHER SETꢅ
Exits the menu setting.
Before you exits the menu setting, select SAVE to
save your settings, or select QUIT to cancel.
ꢅ
0
by
ws
to
•
•
ꢁ (RET)
Returns to the previous menu.
SYSTEM INFOꢅ
LANGUAGEꢅ
ꢂ (HOME)
e.
e
g
ꢀ
Returns to the main menu.
ꢃ (SAVE)
•
•
PROFILE
You can set a mode according to the camera
Used to save your settings of MASK AREA,
PRIVACY ZONE and more.
installation conditions.
us
e
Once you save your settings, they will remain
even if you select QUIT in the menu.
•
•
CAMERA SET
Configure Camera related functions and data.
•
ꢄ (DEL)
INTELLIGENCE
You can configure the settings of motion
detection, tracking and more.
Used to deletes your settings of MASK AREA,
PRIVACY ZONE and more.
Once you delete your settings, they will not be
restored even if you select QUIT in the menu.
•
•
•
PRIVACY ZONE
You can configure the privacy related settings.
OTHER SET
You can configure for Factory Defaults, and more.
SYSTEM INFO.
Displays the system information including the
camera version and communication settings.
•
LANGUAGE
Select a preferred one from the supported
languages.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
PROFILE
ePROFILEf
ꢃSTANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
D
CUSTOM
ꢁ
ꢀ
W
In the PROFILE menu, you can configure the following camera settings at once.
CAMERA SET Menu
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
Previous
Menu
Sub-menus
VPS
IRIS
OFF
ALC
-
ON
ALC
-
OFF
ALC
-
OFF
ALC
-
OFF
ALC
-
ALC
LENS
DC
0
OFF
-
DC
0
OFF
-
DC
0
WDR
-
DC
0
OFF
-
DC
0
OFF
-
LEVEL
BACKLIGHT
WDR
❖
User setting
User setting
User setting
User setting
WEIGHT
WDR LEVEL
WHITE BAL
MID
0
allowed
allowed
allowed
allowed
User setting
allowed
User setting
allowed
(F.FAST)---
MID
User setting
allowed
User setting
allowed
(F.FAST)---
MID
User setting
allowed
User setting
allowed
(F.FAST)---
MID
User setting
allowed
User setting
allowed
SLOW
MID
❖
❖
❖
User setting
allowed
NORM
MID
MOTION
DNR
14 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
CAMERA SET Menu
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
Previous
Sub-menus
Menu
SHUTTER
SENS-UP
XDR
OFF
AUTOx4
MID
AUTO1/250
AUTOx2
MID
OFF
AUTOx4
MID
OFF
AUTOx4
MID
OFF
AUTOx4
MID
DAY/NIGHT
AUTO
AUTO
DAY
AUTO
DAY
NIGHT
BURST
-
-
ON
-
-
-
OFF
OFF
OFF
OFF
WHITE BAL
DAY
DAY/NIGHT
DAY
DAY/NIGHT
DAY
DAY
-
-
-
-
-
MODE
RED
BLUE
NIGHT
ATW2
ATW1
ATW1
ATW1
ATW1
0
0
-
0
0
-
0
0
-
0
0
-
0
0
-
User setting
User setting
User setting
BRIGHTNESS
MODE
MID
ATW2
0
MID
ATW2
0
allowed
allowed
allowed
OFF
User setting
allowed
OFF
User setting
allowed
OFF
User setting
allowed
RED
User setting
allowed
User setting
allowed
User setting
allowed
BLUE
0
2
0
2
DETAIL
ITS
It will be set automatically so you can easily check the traffic conditions.
BACKLIGHT
It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.
2
2
2
❖
❖
❖
DAY/NIGHT
It will be set automatically so it optimizes to the day or night conditions, respectively.
❖
GAMING
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
Setup the general functions of zoom camera module.
Use the cdef switch to select a menu item.
•
CAMERA SETUP
eCAMERA SETf
❖
CAMERA ID
[OFF, ON]
CAMERA ID
VPS
IRIS
MOTION
DNR
OFF
OFF
ꢀCAMERA IDꢀ
ALCꢅ
(F.FAST)---
ABCDEFGHIJKLMNOPQRSTUVWXYZ0
123456789 :?-+*()/
MID
OFF
SHUTTER
SENS-UP
FLICKERLESS
XDR
AUTO X4
(OFF)---
MID
SPffeeSP LOCATIONꢅ
CAMERA-1..................
ꢁ
ꢀ
d
...........................
ꢁ
ꢂ
ꢀ
c
DAY/NIGHT
WHITE BAL
DIGITAL ZOOM
DETAIL
AUTOꢅ
ꢅ
OFF
The CAMERA ID menu is used for you to assign
a unique name to a camera. If you press the
SETUP switch with the CAMERA ID menu
selected, you will see the appropriate screen.
[2]
V-SYNC
INT
AGC COLOR SUP
REVERSE
POSI/NEGA
PIP
LOW
H/V
+
OFF
ꢀ
You can enter up to 54 alphanumeric or
special characters for the CAMERA ID. Select
LOCATION and press the SETUP switch to
move the display position of the CAMERA ID.
ꢁ
d
c
❖
❖
VPS
[OFF, ON]
DIS
OFF
If you set the VPS (Virtual Progressive Scan)
option, the camera will display the image in
progressive format.
IRIS
[ALC]
The IRIS menu is used if you want to adjust the
intensity of radiation incoming to the camera.
ꢁ
ꢀ
16 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
e.
•
ALC (Automatic Light Control)
If you use an ordinary camera in a scene
with an intensive backlight, the object will be
① If you press the SETUP switch with an ALC-
based sub menu selected, you will see the
appropriate screen.
displayed dark on the monitor affected by the
backlight. To solve this problem, you can use
the BLC(Back Light Compensation) function
to improve the sharpness of the image in
such a high contrast scene.
ꢀALCꢀ
LEVEL
[00]----I----
OFF
BACKLIGHT
③
If you set the BACKLIGHT option to WDR, you will
see a menu where you can set the WDR options.
You can adjust the shutter speed in WDR LEVEL
and the brightness in WEIGHT.
ꢁ
ꢂ
ꢀ
You can also select any of OUTDOOR, and
INDOOR in WHITE BAL.
ꢀALCꢀ
The LEVEL menu is used to adjust the
overall brightness, where “+” will increase the
brightness and “–” will decrease it.
n
LENS
DC
LEVEL
BACKLIGHT
WEIGHT
[ 00]----I----
WDR
MID
[ 0]----I----
INDOOR
② If you set the BACKLIGHT option to BLC,
you will see a menu where you can set the
BLC area.
WDR LEVEL
WHITE BAL
ꢁ
ꢂ
ꢀ
you can set the desired BLC zone by defining
the size and location.
WDR(Wide Dynamic Range) extends the gain range of
the screen that is mostly useful if you take a simultaneous
picture of both indoor and outside of the window.
Namely, it improves the sharpness of the
picture in outdoor scenery as well as indoor.
ꢀALCꢀ
LEVEL
BACKLIGHT
AREA
[00]----I----
BLC
USER
<SIZE>ꢅ
<LOCATION>ꢅ
Note :
–
If you use the VPS (Virtual Progressive Scan) function, the CCD
ꢁ
ꢂ
ꢀ
reads differently so you can not use WDR simultaneously.
If you set VPS to ON, WDR will be automatically set to OFF.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
[OFF, VERY LOW, LOW, MID, HIGH, VERY
HIGH, USER, FIX]
❖
AGC
ꢀAGC FIXꢀ
[01]
LEVEL
The AGC (Auto Gain Control) menu is used to
set the AGC level of the camera. When the AGC
is active, the camera automatically increases the
sensitivity by amplifying the Video signal when
the strength of the signal falls below the normal
value.
❖
ꢁ
ꢂ
ꢀ
If OFF or FIX mode is selected in the SENS-UP
If you press the SETUP switch with a FIX sub
menu, you can specify the AGC level.
menu selected, you will see the appropriate screen.
If you press the SETUP switch with a USER
sub menu selected, you will see the appropriate
screen.
❖
As a fixed value of the AGC gain is used in FIX
mode, you can select one of the 16 detailed levels
from VERY LOW to VERY HIGH before fixing it.
ꢀAGC USERꢀ
FIX mode is not available if you set the
BACKLIGHT function to WDR.
LEVEL
[16]
Note :
–
If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the AGC menu will be deactivated.
–
If FLICKERLESS is set to ON, the AGC FIX mode will be disabled.
ꢁ
ꢂ
ꢀ
❖
MOTION
[S.SLOW, SLOW, NORM, FAST, F.FAST]
The MOTION menu is used to adjust the strength
of the AGC level for a control of the camera motion.
This is available only if the SENS-UP menu is set
to AUTO.
You can select one from S.SLOW, SLOW, NORM,
FAST and F.FAST for the AGC level.
In USER mode, you can break down the level in
16 steps from VERY LOW to VERY HIGH to your
preference.
If you monitor a fast moving object in a low contrast
scene, select F.FAST while select S.SLOW for a
hardly moving object in the same lighting condition.
18 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
Note :
If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the MOTION menu will be deactivated.
Note :
–
–
–
–
If the SENS-UP function is set to AUTO, only items of
OFF and AUTO are available in the SHUTTER menu.
If the SENS-UP mode is set to FIX, the SHUTTER menu
will be deactivated.
❖
DNR
[OFF,LOW,MID,HIGH, USER(1~16)]
You can configure the DNR (Digital Noise
If the FLICKERLESS function is set to ON, the SHUTTER menu
will be deactivated.
Reduction) related settings.
Reduces the noise on the screen.
This is especially useful for a severely distorted
screen.
❖
SENS-UP
[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO
X8, AUTO X12, AUTO X16, AUTO X24, AUTO
X32, AUTO X48, AUTO X64, AUTO X96, AUTO
X128, AUTO X256, AUTO X512, FIX X2, FIX
X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24,
FIX X32, FIX X48, FIX X64, FIX X96, FIX X128,
FIX X256, FIX X512]
You can set the level if you set DNR to USER.
n.
s
❖
SHUTTER
[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,
AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO
1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]
Automatically detects the ambient level of
darkness in the dark or low contrast scene to
extend the accumulated time, keeping the image
bright and sharp; It can be also used as FIX mode.
The SHUTTER menu is used to configure settings
of the fixed / auto high-speed electronic shutter.
You can select one of 7 options from 1/100(PAL:1/120)
to 1/10K for the fixed high speed electronic shutter,
which is mostly used for imaging a fast moving object.
Note :
d.
–
–
–
–
If the SHUTTER menu is set to fixed electronic shutter
ST]
mode, the SENS-UP menu will not be available.
The auto high speed electronic shutter operates
as the fixed high speed shutter in a high contrast
scene but automatically focuses the target if the
iris opens fully in a low contrast scene like in ELC
mode. When it gets brighter back, the mode will
switch to the fixed high speed electronic shutter
mode.
If FLICKERLESS is set to ON, the FIX mode of the SENS-
UP menu will be disabled.
n.
If the SHUTTER menu is set to AUTO, the SENS-UP
menu can be set to either OFF or AUTO mode.
M,
If the BACKLIGHT function is set to WDR, the SENS-UP menu
can not be set to FIX.
st
n.
However, the auto high speed shutter operates
properly only in a camera featuring a DC or VIDEO lens.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
❖
FLICKERLESS
[OFF, ON]
If you press the SETUP switch with a NIGHT sub
menu selected, you will see a menu where you can
set Burst to OFF/ON.
If BURST is set to ON, the Burst signal will output
together with the black-and-white composite video
signal. If BURST is set to OFF, the Burst signal does
not output.
You can set the BURST option to OFF/ON, or
select to output the Burst signal in NIGHT mode.
If set to ON, the shutter speed will be fixed to
1/100(PAL:1/120) second. This will prevent possible screen
distortion due to a mismatch between the vertical sync
frequency and the blinking frequency of the lighting.
Note :
–
–
–
If the SHUTTER menu is set to AUTO or FIX mode, the
FLICKERLESS menu will not be available.
If the SENS-UP function is set to FIX mode, the Flickerless
menu will be deactivated.
•
AUTO
The camera will automatically switch between
DAY and NIGHT mode, according to the lighting
condition.
If AGC is set to FIX mode, the FLICKERLESS function will
be disabled.
❖
XDR (eXtended Dynamic Range)
[OFF, LOW, MID, HIGH]
If you press the SETUP switch with an AUTO-
based sub menu selected, you will see the
appropriate screen.
Actively controls the gamma compensation in the
way it operates the ambient luminance contrast
in a certain pixel unit to determine the optimal
visibility.
ꢀAUTOꢀ
BURST
OFF
DAYÆNIGHT
BRIGHTNESS
DWELL TIME
NIGHTÆDAY
BRIGHTNESS
DWELL TIME
MASK AREA
MID
2S
Select one from OFF, LOW, MID and HIGH.
Closing to HIGH will increase the compensation
level.
MID
5S
2
1
❖
DAY/NIGHT
[DAY,NIGHT,AUTO,EXT]
ꢁ
ꢂ
ꢀ
•
DAY
If set to DAY, it will be fixed to DAY mode
You can set the BURST option to OFF/ON, or
regardless of the ambient conditions.
select to output the Burst signal in NIGHT mode.
•
NIGHT
The BRIGHTNESS of DAYÆNIGHT sets the
brightness degree of color to BW switching,
for which you can select from LOW, MID, and
If set to NIGHT, it will be fixed to Black-and-White
mode regardless of the ambient conditions.
20 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
HIGH. As you adjust it from HIGH to LOW, the
The MASK is only for determining the mode
switching, and any excessive bright area at night
will be excluded by the configured MASK.
screen switches to black and white mode under
the darker situation.
DWELL TIME of DAYÆNIGHT sets the time to
maintain switched black and white mode.
Note :
–
If BACKLIGHT is set to BLC, the MASK AREA function will
es
be deactivated.
The BRIGHTNESS of NIGHTÆDAY sets the
brightness degree of BW to color switching, for
which you can select from LOW, MID, and HIGH.
As you adjust it from HIGH to LOW, the screen
switches to color mode under the darker situation.
•
DAY
This enables an auto switch between DAY and NIGHT
mode using the interface with the external sensor.
DWELL TIME of NIGHTÆDAY sets the time to
❖
WHITE BAL
[DAY/NIGHT]
maintain switched color mode.
g
If you want to adjust the color scheme, use the
WHITE BALANCE function.
The MASK AREA menu is used to prevent
unintended mode switching or inability of
determining the switching due to existence of
high spot light source at night.
•
DAY
In DAY mode, you can set the color values of
RED and BLUE. The screen will be displayed in
colors according to your settings.
If you press the SETUP switch in item 1 or 2 of
the MASK AREA menu, you will see a menu
where you can specify an area to MASK.
ꢀWHITE BALꢀ
DAY/NIGHT
MODE
DAY
AWCꢅ
ꢀ
MASK AREAꢀ
RED
[00]----I----
[00]----I----
[0248]
<SIZE>
ꢅ
BLUE
<LOCATION>ꢅ
R-GAIN
B-GAIN
[0247]
ꢁ
ꢂ
ꢀ
e.
ꢁ
ꢃ
ꢄ
ꢂ
ꢀ
Note :
–
You can set the values of R-GAIN and B-GAIN only in
AWC mode.
You can specify MASK 1 and 2 simultaneously.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
•
NIGHT
the ambient conditions. The color temperature
ranges from approx. 2500K to 9300K.
ATW2: The color temperature ranges from
approx. 2,000K to 10,000K.
AWC ( Auto White Balance Control): If you
press the SETUP switch in the appropriate item
position, Auto White Balance will perform once.
3200K : Set color temperature to 3200K
5600K : Set color temperature to 5600K
RED : Adjusts the strength of the red color.
BLUE : Adjusts the strength of the blue color.
R-GAIN/B-GAIN : Enables you to set the current
color temperature manually.
BRIGHTNESS : Select a brightness level in
switching from setting in DAY mode to setting in
NIGHT mode.
Use the NIGHT mode if you want to set the white
balance differently according to the ambient
luminance.
If the NIGHT mode is set to OFF, the white
balance will always operate as set in DAY mode;
if not to OFF, the camera will switch to as set in
DAY/NIGHT mode according to the brightness.
In NIGHT mode, you can set the values of RED,
BLUE and BRIGHTNESS. The screen will be
displayed in colors according to your settings.
•
•
•
•
–
–
–
-
L
c
r
ꢀWHITE BALꢀ
e
DAY/NIGHT
BRIGHTNESS
MODE
NIGHT
MID
AWCꢅ
–
RED
[00]----I----
[00]----I----
[0248]
BLUE
R-GAIN
B-GAIN
❖
DIGITAL ZOOM
[ON/OFF]
[0247]
ꢁ
ꢂ
ꢀ
You can set the digital zoom factor and position.
If you press the SETUP switch with the DIGITAL
ZOOM function set to ON, you will see the
appropriate screen.
❖
❖
Note :
–
You can set the values of R-GAIN and B-GAIN only in
AWC mode.
When the zoom factor and position are defined,
the digital zoom function will operate.
–
If AGC is set to OFF or FIX, you can not access the
NIGHT menu.
–
For adjusting the white balance, the following
5 modes are provided:
•
ATW1(Auto Tracing White Balance mode
1): The camera can automatically adjust the
color temperature in real time, according to
22 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
Note :
Use of DC 12V will fix V-SYNC to INT, which can not be
changed.
e
ꢀDIGITAL ZOOMꢀ
–
RATIO
[X1.0]
< LOCATION >
ꢅ
❖
AGC COLOR SUP
[LOW , MID, HIGH]
Adjust the color scheme according to the AGC value.
m
e.
❖
❖
❖
REVERSE [OFF, H, V, H/V]
Mirrors video signals horizontally, vertically, or both.
POSI/NEGA [+, -]
Output as it is or mirror the video brightness signal.
PIP [OFF, ON]
ꢁ
ꢂ
ꢀ
-
LOCATION : If you press the SETUP switch in the
condition where the image is enlarged as much as the
ratio setting, you can watch an invisible area of the
effective screen as well using the cdef switch.
t
Displays a sub image together with the main image on
the same screen using the Picture In Picture function.
Note :
Note :
–
–
If the digital zoom factor is set to larger than 1x, the FENCE
function will be deactivated.
If more than one privacy zone is set and the PRIVACY SET is
set to ON, the PIP function will be deactivated.
The DIGITAL ZOOM function enlarges the pixel itself, which can
cause deterioration of the quality.
–
If the INTELLIGENCE function is set to FENCE mode, the PIP
menu will be deactivated.
.
L
❖
DETAIL
[0~3]
❖
DIS
[OFF, ON]
Controls the horizontal or vertical distinction.
Digital Image Stabilization will set the anti-shake
compensation.
❖
V-SYNC [INT, LINE]
Select the vertical sync mode for INT or LINE.
Note :
If you select INT, the camera will use the internal
synchronization.
–
If you set DIS to ON, the compensation area will be enlarged as
set in the digital zoom factor.
If selecting LINE, the camera will use the external
If you set the digital zoom factor to greater than the enlarged
zoom factor for the compensation, the DIS function will be
deactivated.
power source frequency for the synchronization.
You can adjust the LL-PHASE.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
•
FENCE
INTELLIGENCE
This is to detect if a moving object passes
through the specified LINE or AREA.
eINTELLIGENCEf
In a condition where a moving object is detected
in an analysis of the previous and current frames
whose movement overlaps a certain area, the
system displays “PASS” if the object’s center line
passes through the line while it displays “ENTER” or
“EXIT” if the center point passes through the area.
MOTION
OFF
OFF
2 3 4
ON
ADVANCED
MASK AREA
DISPLAY
SENSITIVITY
RESOLUTION
1
[4]
[5]
ꢁ
ꢀ
ꢀFENCEꢀ
LINE
AREA
OFF
OFF
You can set the motion detection and tracking in the
INTELLIGENCE menu.
❖
MOTION
[OFF,TRACKING,DETECTION]
ꢁ
ꢂ
ꢀ
•
TRACKING
Detects and tracks a moving object.
You can set the position and detection direction of the
•
DETECTION
Detects a moving object.
LINE, and the size and position of the AREA.
- How to set the line
Note :
If it is set to DETECTION, you can not set such functions as
FIXED/MOVED and FENCE in the ADVANCED menu.
ꢀLINEꢀ
–
PIXEL LEVEL
<POINT>
[4]
ꢅ
DIRECTION
§¨
❖
ADVANCED
[OFF, FIXED/MOVED, FENCE]
Detects a motion of an object and displays an
image of any moving object before tracking the
moving route.
ꢁ
ꢂ
ꢀ
24 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
① If you press the SETUP switch with the LINE
and size of the area.
option set to ON, you can specify the position
② If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a
single pressure of the cdef switch.
and detection direction of the line.
② If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a
single pressure of the cdef switch.
③
In <SIZE>, press the SETUP switch and use
the cdef switch to adjust the size.
Press the SETUP switch again to complete the
sizing.
③
In <POINT>, you can specify the first position of
the line by pressing the SETUP switch once, and
the second position by pressing the switch again.
Use the cdef switch to specify the
position.
Set each position of the two points and press the
SETUP switch to complete the positioning.
or
④
In <LOCATION>, press the SETUP switch and
use the cdef switch to specify the position.
Press the SETUP switch again to complete
the positioning.
Note :
④
If you change the DIRECTION, you can specify
the detection direction. The detection direction
based on the defined two points will be
displayed on the screen.
–
If you set the LINE of the FENCE to ON, PRIVACY 12 will
not be available.
Functions of FENCE, PIP, DIS and DIGITAL ZOOM (if the
digital zoom factor is set to larger than 1x) can not be
used simultaneously.
- How to set the area
e
–
In the boundary of the defined AREA and LINE, a FENCE
detection error may occur if two or more moving objects
overlap with each other or one object separates in
multiple directions.
ꢀ
AREAꢀ
PIXEL LEVEL
<SIZE>
[4]
ꢅ
<LOCATION>ꢅ
•
FIXED/MOVED
If an object on the screen suddenly disappears or
an object comes out of nowhere and stays for a
certain time, the area will be displayed.
ꢁ
ꢂ
ꢀ
A detection (FIXED/MOVED) error may occur if :
- multiple motions occur continuously in random
directions
① If you press the SETUP switch with the AREA
option set to ON, you can specify the position
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
- a fixed object moves in one position continuously
Us
PR
PRIVACY ZONE SETUP
- a second object screens the first moving object
Se
SE
sp
ePRIVACY ZONEf
❖
MASK AREA [1~4]
Specify a detection exception area to mask.
1
7
2
3
4
5
6
8
9
10 11 12
LE
Select a mask number and specify the size and
position.
PRIVACY SET
STYLE
ON
MOSAIC1
ꢀ
MASK AREAꢀ
ꢁ
ꢀ
<SIZE>
ꢅ
<LOCATION>ꢅ
The PRIVACY function will protect your privacy by
screening the privacy area that you have specified
during monitoring. You can specify up to 12 privacy
zones.
ꢁ
ꢃ
ꢄ
ꢂ
ꢀ
If you set the PRIVACY SET to ON, your PRIVACY
ZONE settings will be applied.
❖
DISPLAY
[ON, OFF]
You can change the style to adjust the mosaic size
and color of the PRIVACY ZONE.
With the DISPLAY option set to ON, a motion or
a set ADVANCED function will be displayed on
the screen, if detected.
ePRIVACY ZONEf
1
2
3
4
5
6
7
8
9
10 11 12
❖
❖
SENSITIVITY
[1~7]
PRIVACY SET
STYLE
Y-LEVEL
RED
BLUE
ON
COLOR
[128]
[128]
[128]
Set the sensitivity of the motion detection.
RESOLUTION
[1~5]
ꢁ
ꢀ
If setting it to high, the camera can detect even a
trivial movement of the target.
26 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
① By pressing the SETUP switch in
<POSITION>, you can move the overall
position of the privacy zone.
Use the cdef switch to select one from
PRIVACY 1 through 12.
Select one from PRIVACY 1~12 and press the
SETUP switch to confirm your setting. You can
specify a pixel that moves as you change the PIXEL
LEVEL to set the position.
② Use the cdef switch to move the
position and press the SETUP switch to
confirm it.
Note :
ꢀPRIVACY ZONE SET1ꢀ
–
If more than one PRIVACY ZONE is specified and the
PRIVACY SET is set to ON, the PIP function will be
deactivated.
PIXEL LEVEL
<POINT>ꢅ
<POSITION>ꢅ
[4]
–
If the 12th PRIVACY ZONE is specified, the LINE function
of FENCE will be deactivated.
OTHER SET
ꢁ
ꢃ
ꢄ
ꢂ
ꢀ
eOTHER SETf
EXTERNAL TRG
FACTORY DEFAULTS
OSD COLOR
OFF
ꢅ
BW
- How to set the point
You can set each position of the 4 points.
① If you press the SETUP switch in <POINT>,
you will see the points available in the
PRIVACY ZONE. Each time you press the
SETUP switch, the points available will move.
ꢁ
ꢀ
② Use the cdef switch to set the position
of each point. Set each position of the four
points and press the SETUP switch to
complete the positioning.
❖
EXTERNAL TRG
Set the EXTERNAL TRG menu to ON and press
the SETUP switch to display the appropriate
screen.
- How to set the position
You can move the position of the overall area.
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
❖
SYSTEM INFORMATION
ꢀEXTERNAL TRGꢀ
STILL TIME
DELAY TIME
OFF
FIX
eSYSTEM INFOf
3_VAR_WDR_
TYPE
P
SERIAL NO. 000000000000000
CAMERA VER.
0.50_090101
ꢁ
ꢀ
ꢁ
ꢀ
You can set the STILL TIME to 0~4 seconds.
If DELAY TIME is set to FIX, the DELAY TIME will
be set in sync with the STILL TIME; if set to USER,
the DELAY TIME will be set to your setting.
You can check the system information such as
SERIAL NO and CAMERA VER.
Note :
–
If VPS is set to OFF, the EXTERNAL TRG menu will be
deactivated.
LANGUAGE
eLANGUAGEf
❖
FACTORY DEFAULTS
All the settings will be restored to the factory
default.
However, the settings of PROTOCOL, BAUD
RATE, ADDRESS and LANGUAGE will not be
restored to the default.
ꢃENGLISH
PУCCKNЙ
POLSKI
ČESKY
TÜRKÇE
ꢁ
ꢀ
❖
OSD COLOR
[BW, R/G/B]
You can set the OSD(On-screen Display) color to
COLOR or B/W.
The camera supports 5 different languages.
Select a preferred language.
28 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use OSD Menu
❖ Initial Configuration Table
Camera Configuration
•
CAMERA ID
VPS
OFF
OFF
ALC
IRIS
AGC
VERY HIGH
(F.FAST)
MID
MOTION
DNR
SHUTTER
SENS-UP
FLICKERLESS
XDR
OFF
AUTO x4
(OFF)
MID
DAY/NIGHT
DIGITAL ZOOM
DETAIL
AUTO
OFF
[2]
AGC COLOR SUP
REVERSE
POSI/NEGA
PIP
MID
H/V
+
OFF
DIS
OFF
V-SYNC
INT
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
SPECIFICATIONS
Items
Sub-items
SCC-B5397N/SCC-5399N
Camera Type
CCTV Camera (WDR & DAY/NIGHT)
Device
1/3” Super-HAD PS CCD
811 x 508
Image
Total
Pixels
Effective
768 x 494
System
Interlace/Progressive
525 lines
Scanning Line
Frame
30frame/1sec
Scanning
Internal Mode
15,734 Hz
Horizontal
Frequency
Line-lock Mode
Internal Mode
Line-lock Mode
Condition
15,750 Hz
59.94 Hz
Vertical
Frequency
60 Hz
Min. Scene illumination
Sens-up
OFF
OFF
F No.
1.2
1.2
Level
DAY
0.4
0.24
NIGHT
0.04
0.024
50
30
IRE
IRE
Lux
Lux
Lux
Lux
Min. Scene
Illumination
OFF
1.2
1.2
1.2
1.2
15
50
30
15
IRE
IRE
IRE
IRE
0.12
0.0008
0.0005
0.00023
Lux
Lux
Lux
Lux
0.012
0.00008
0.00005
0.000023
Lux
Lux
Lux
Lux
512 times
512 times
512 times
Number of Privacy Zone
Day/Night
12 (Polygonal Method)
DAY/NIGHT/AUTO/EXT
OFF/Tracking/Detection
Off/On (Level Setting)
Off/On (x128)
Motion Detection
eXtended Dynamic Range(XDR)
Wide Dynamic Range(WDR)
Virtual Progressive Scan(VPS)
D-Zoom
Functions
Off/On
x1 ~ x16 (x0.1 STEP)
Off/On
PIP
High Speed Shutter
Flickerless
1/60 ~ 1/10Ksec (OSD/External Control)
Off/On
30 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
s
Items
Sub-items
Sens-Up
SCC-B5397N/SCC-5399N
x2 ~ x512
AGC
Off/On (Max.Level Setting)
Off/On (Phase Control)
Off/On (Max.54ea/2Line)
ATW1/ATW2/AWC/3200K/5600K
Off/On (Adaptive 3D+2D)
Off/On
Line Lock
Camera ID
White Balance
Digital Noise Reduction(DNR)
Digital Image Stabilization(DIS)
Intelligent Video
Etc. Function
Horizontal
Fixed/Moved, Fence
Detail, Reverse(H/V), Posi/Nega
600 TV Lines
Resolution
Vertical
350 TV Lines
Video Output
S/N Ratio
-
VBS 1.0Vp-p, 75 Ω
Approx. 52dB
S/N Ratio
Auto Iris (DC)
Lens
Lens Drive Type
SCC-B5397 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2
SCC-B5399 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2
0 ~ 355°(100° in CW(Clockwise) direction,
255° in CCW (Counterclockwise) direction)
PAN
TILT
Range
Range
0 ~ 90°
Remote
Control
Coaxitron (Data On Coax cable)
Yes (with SCX-RD100)
Operating Temperature
Humidity
-10˚C ~ +50˚C
Less than 90%
AC24V 10%(60Hz 0.3Hz)
DC12V 10%
About 2.6W
Environmental
Conditions
Power Requirement
Power
Power Consumption
Dimensions (Ø x H)
Weight
150(Ø) x 121(H)mm
980g
Physical
Specification
Color
White
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Items
Sub-items
SCC-B5397P/SCC-5399P
CCTV Camera (WDR & DAY/NIGHT)
Camera Type
Device
1/3” Super-HAD PS CCD
795 x 596
Image
Total
Pixels
Effective
752 x 582
System
Interlace/Progressive
625 lines
Scanning Line
Frame
25frame/1sec
Scanning
Internal Mode
15,625 Hz
Horizontal
Frequency
Line-lock Mode
Internal Mode
Line-lock Mode
Condition
15,625 Hz
50 Hz
Vertical
Frequency
50 Hz
Min. Scene illumination
Sens-up
OFF
OFF
F No.
1.2
1.2
Level
DAY
0.4
0.24
NIGHT
0.04
0.024
50
30
IRE
IRE
Lux
Lux
Lux
Lux
Min. Scene
Illumination
OFF
1.2
1.2
1.2
1.2
15
50
30
15
IRE
IRE
IRE
IRE
0.12
0.0008
0.0005
0.00023
Lux
Lux
Lux
Lux
0.012
0.00008
0.00005
0.000023
Lux
Lux
Lux
Lux
512 times
512 times
512 times
Number of Privacy Zone
Day/Night
12 (Polygonal Method)
DAY/NIGHT/AUTO/EXT
OFF/Tracking/Detection
Off/On (Level Setting)
Off/On (x160)
Motion Detection
eXtended Dynamic Range(XDR)
Wide Dynamic Range(WDR)
Virtual Progressive Scan(VPS)
D-Zoom
Off/On
Functions
Max. x16
PIP
Off/On
High Speed Shutter
Flickerless
1/50 ~ 1/10Ksec (OSD/External Control)
Off/On
x2 ~ x512
Sens-Up
BLC
Off/On (Area Setting)
32 – DIGITAL COLOR DOME CAMERA
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Items
Sub-items
AGC
SCC-B5397P/SCC-5399P
Off/On (Max.Level Setting)
Off/On (Phase Control)
Off/On (Max.54ea/2Line)
ATW1/ATW2/AWC/3200K/5600K
Off/On (Adaptive 3D+2D)
Off/On
Line Lock
Camera ID
White Balance
Digital Noise Reduction(DNR)
Digital Image Stabilization(DIS)
Intelligent Video
Etc. Function
Horizontal
Fixed/Moved, Fence
Detail, Reverse(H/V), Posi/Nega
600 TV Lines
Resolution
Vertical
350 TV Lines
Video Output
S/N Ratio
-
VBS 1.0Vp-p, 75 Ω
Approx. 52dB
S/N Ratio
Auto Iris (DC)
Lens
Lens Drive Type
SCC-B5397 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2
SCC-B5399 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2
0 ~ 355°(100° in CW(Clockwise) direction,
255° in CCW (Counterclockwise) direction)
PAN
TILT
Range
Range
0 ~ 90°
Remote
Control
Coaxitron (Data On Coax cable)
Yes (with SCX-RD100)
Operating Temperature
Humidity
-10˚C ~ +50˚C
Less than 90%
Environmental
Conditions
AC24V 10%(50Hz 0.3Hz)
DC12V 10%
Power Requirement
Power
Power Consumption
Dimensions (Ø x H)
Weight
About 2.6W
150(Ø) x 121(H)mm
980g
Physical
Specification
Color
White
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
|