Samsung Home Security System SVD 4120A AW User Guide

Vandal-Proof Color Dome Camera  
INSTRUCTION MANUAL  
SVD-4120A/AW  
About this manual  
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.  
SALES NETWORK  
SAMSUNG TECHWIN CO., LTD.  
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,  
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703  
SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)  
Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,  
U.S.A  
TEL: 82-31-740-8137~41 FAX: 82-31-740-8145  
TEL : (201) 902-0347 FAX: (201) 902-0429  
SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)  
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)  
Samsung House, 1000 Hillswood Drive Hillswood Business  
Park Chertsey Surrey KT16 OPS  
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China  
Post Code : 300190  
TEL: 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325  
TEL : 86-22-2761-9698 FAX: 86-22-2761-6514  
P/No. : 6806-0458-01B  
VAN 04. 10  
SAMSUNG CCTV CAMERA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning  
Features  
The camera needs periodic inspection.  
Fine Picture Condition Under Very  
Low Illumination (SENSE UP)  
IP66 Approved / Dust and Rain  
Resistant  
Contact an authorized technician for inspection.  
1/3 high density CCD and digital  
processor permit high quality pictures to  
be captured in very low light condition.  
With dust and rain resistant design, the  
camera can be installed outside under  
building eaves or places that are exposed  
to the dust and rain.  
Stop using your camera when you find a malfunction.  
If you use your camera around smoke or unusual heat for a long time, a fire may  
be caused.  
SSNR(Samsung Super Noise  
Reduction) CHIP  
High Resolution  
The horizontal resolution of 500TV lines  
can be achieved by using a high density  
CCD having Double Speed 410,000 pixels  
SONY CCD, which provides clean,  
noiseless and reliable pictures.  
SVD-4120A/AW has an assistant DSP  
chip that can remove image noise  
efficiently and it shows clean and obvious  
image in low luminance  
Do not Install the camera on a surface that can not support it.  
Unless the surface is suitable, it could cause falling or other hazards.  
Auto Iris Vari-Focal Lens Built In  
Electronic DAY/NIGHT  
Do not hold plug with wet hands.  
The focal length of lens is 3.8 to 9.5 mm,  
equivalent to 2.5x zoom.(2.5 to 6.0mm,  
equivalent to 2.4x zoom/SVD-4120AW)  
The built-in lens allows the camera to  
have a Wider Dynamic Range, therefore  
you can use in various applications.  
In normal or high luminance, camera  
maintains color mode. On the contrary, it  
get changed into B/W mode in low  
luminance.  
It could cause an electric shock.  
Do not disassemble the camera.  
It may result in fire, electric shock or other hazards.  
Wide Range ATW  
The White Balance can be automatically  
adjusted in response to light condition so  
that you can observe in an appropriate  
color balance.  
Do not use the camera close to a gas or oil leak.  
It may result in fire or other hazards.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Setting Up The Menu  
CAMERA ID  
16  
17  
20  
21  
22  
25  
26  
27  
28  
28  
30  
8
Precautions  
BACKLIGHT  
10  
11  
13  
Composition  
WHITE BALANCE  
• MOTION DETECTION  
• IRIS LEVEL CONTROL  
SHUTTER SPEED CONTROL  
SESE UP  
Name and Function of Each Section  
Connection  
GAIN  
Connecting to Monitor  
Connecting to Power  
13  
14  
SSNR  
SPECIAL  
32  
Operating Your Camera  
15  
15  
Troubleshooting  
Configuration of The Menu  
34  
35  
Dimention  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
Do not install the camera in  
extreme temperature conditions.  
Do not install or use the camera in an  
environment where the humidity is high.  
Do not drop the camera or  
subject them to physical shocks.  
Never keep the camera face to  
strong light directly.  
Only use the camera under conditions  
where temperatures are between -10˚C  
and +50˚C. Be especially careful to provide  
ventilation when operating under high  
temperatures.  
It can cause the image quality to be poor.  
It can cause malfunctions to occur.  
It can damage the CCD.  
Do not expose the camera to  
radioactivity.  
Do not install the camera under  
unstable lighting conditions.  
Do not touch the front lens of  
the camera.  
If it is exposed to radioactivity, For  
heated CCD, it will be out of order.  
Not es  
• If the camera is exposed to spotlight or object reflecting strong light, smear or  
blooming may occur.  
Please check that the power satisfies the normal specification before connecting  
the camera.  
Severe lighting change or flicker can cause  
the camera to work improperly.  
It is one of the most important parts of  
the camera. Be careful not to be stained  
by fingerprint.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
8
9
Name and Function of Each Section  
Composition  
1. SVD-4120A/AW  
2. Instruction Manual  
3. Quick Install Guide  
4. Wrench  
5. Ø5 Tapping Screws 4EA  
6. Template  
7. Video Output Cable for installer  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
10  
11  
Connection  
Name and Function of Each Section  
Pan Base  
control panning angle of camera  
Connecting to Monitor  
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.  
Tilt Base Holding Serews  
fix tilted position.  
Pan Base Holding Screws (Color : Silver)  
fix panned position  
Zoom Handle  
adjust zoom between WIDE and TELE  
Focus Handle  
after adjusting zoom, adjust focus  
CCTV Camera  
Monitor  
SET Button  
confirm the status of the selected feature  
As the connecting method varies with the instruments, refer to the manual  
supplied with the instrument.  
RIGHT Button  
move cursor to the right, change the status of the selected feature  
If necessary, you can connect the monitor to the REMOTE jack on the back of  
your camera.  
DOWN Button  
move cursor to the down, select the desired feature item  
Only connect the cable when the power is turned off.  
UP Button  
move cursor to the up, select the desired feature item  
Set the 75/ Hi-Z selection switch as shown below if you have an intermediate  
device.  
LEFT Button  
move cursor to the left, change the status of the selected feature  
Intermediate End monitor  
Video Output Terminal  
Video Output Terminal to Monitor  
Video Output Jack  
Power Input Jack  
Shield Case  
CCTV Camera  
Dome Cover  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
12  
13  
Connection  
Operating Your Camera  
Connecting to Power  
Configuration of The Menu  
SETUP MENU  
CAMERA ID (see page 17)  
OFF • ON  
Use AC 24V / 300mA or DC 12V / 500mA power source.  
BACKLIGHT (see page 20)  
WDR • BLC • OFF  
WHITE BAL. (see page 21)  
W-ATW • S-ATW • AWC • MANUAL  
MOTION DET. (see page 22)  
OFF MD1 • MD2  
IRIS LEVEL CONTROL (see page 25)  
• LEVEL  
For DC Power Type  
SHUTTER (see page 26)  
For DC power as the voltage drop according to the length of the cable in the  
above table, a camera may malfunction if there is an excessively long cable run.  
OFF 1/100 (1/120) • MANUAL  
SENSE UP (see page 27)  
Auto OFF  
Resistance of copper wire [at 20C˚ (68˚F)]  
2
Copper wire size (AWG)  
Resistance ( / m)  
Voltage Drop (V/m)  
#24(0.22mm )  
#22(0.33mm2)  
#20(0.52mm2)  
0.030  
#18(0.83mm2)  
0.018  
0.078  
0.050  
GAIN (see page 28)  
OFF • AGC-L AGC-H  
0.028  
0.018  
0.011  
0.006  
* Voltage for camera operation: 12V DC 10%  
* Voltage drops in the above table are variable according to types of cable manufacturer.  
SSNR (see page 28)  
OFF LOW MIDDLE • HIGH  
Not es  
SPECIAL (see page 30)  
COLOR • SYNC • PRIVACY • RESET  
Be sure to connect power only after all the installation is complete.  
Note that AC or DC adaptor is not supplied with camera.  
Use the UL listed, class 2 power transformer of AC 24V adaptor.  
Ground should be connected to the GND terminal.  
END  
EXIT  
EXIT  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
14  
15  
Operating Your Camera  
SETUP  
Setting Up The Menu  
CAMERA ID  
OFF  
Change the status using  
the LEFT or RIGHT button.  
Select the function using  
the UP or DOWN button.  
BACKLIGHT  
WHITE BAL.  
WDR  
Use the five SETUP MENU buttons on back of the camera.  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
AGC-L  
MIDDLE  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
LEFT button  
UP button  
DOWN button  
RIGHT button  
SSNR  
SPECIAL  
EXIT  
3. Change the status of the selected feature using the LEFT or RIGHT button.  
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.  
SET button  
Not es  
For the mode with you can access submenu.  
You can access submenu using SET button.  
1. Press the SET button to access the SETUP mode.  
SETUP menu is displayed on the monitor screen.  
SETUP  
CAMERA ID  
OFF  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
WDR  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
If you enter a CAMERA ID, the name will be displayed in the screen monitor.  
1. Press the SET button to display the SETUP menu and move the arrow  
indicator to 'CAMERA ID' using the UP or DOWN button.  
2. Set 'CAMERA ID' to 'ON' using the LEFT or RIGHT button.  
AGC-L  
MIDDLE  
SSNR  
SPECIAL  
EXIT  
Not es  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
OFF  
• If the CAMERA ID feature is set to 'OFF', the name  
will not displayed in the monitor.  
WDR  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
2. Select the desired feature using the UP or DOWN button.  
Each time you press the UP or DOWN button, the arrow indicator moves up  
or down.  
AGC-L  
MIDDLE  
SSNR  
SPECIAL  
EXIT  
Move the arrow indicator to the desired feature item.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
16  
17  
Operating Your Camera  
3. Press SET button.  
5. Select the position at which the CAMERA ID will be located on the screen.  
Move the cursor to 'POS' and press SET button.  
CANERA ID  
CAMERA ID  
POS  
CLR RESET END  
POS  
CLR RESET END  
4. You can enter up to 16 characters.  
The CAMERA ID is displayed on the bottom-left of the monitor screen.  
(Default position)  
Move the cursor to character-enter location by using the LEFT or RIGHT button.  
Select the desired character by using UP or DOWN button.  
The factory defualt characters are A, B, ···, a, b, ···, ., -, ··· 0, 1···, 8, 9  
CAMERA ID  
FRONT DOOR  
POS  
CLR RESET END  
Select the position by using the 4-directional buttons, then press the SET  
button to confirm the position.  
Press the SET button to confirm the blinking character. The first character is  
saved and the cursor in the bottom of the screen moves to the next position.  
Repeats steps  
,
and until you create the full name you want.  
FRONT DOOR  
Not es  
• If you make a mistake while entering name  
Move the cursor to ‘CLR’, press ‘SET’ button.  
After erasing the character from right to left, correct the character again.  
6. When completed, move the cursor to 'END' and press SET button.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
18  
19  
Operating Your Camera  
4. When completed, press the SET button.  
BACKLIGHT  
Not es  
SV-II DSP chip built-in provides intelligent light level control to overcome the  
severe Backlight conditions.  
• If you select WDR mode, the following phenomenon may appear by lighting  
condition. In these cases do not select WDR mode.  
1. Press the SET button to display the SETUP menu and move the arrow  
indicator to ‘BACKLIGHT’ using the UP or DOWN button.  
Unnatural color change or unnatural phenomenon on the screen  
Noise of bright part on the screen  
SETUP  
According to the area of bright part on the screen there may be the difference of  
WDR performance so be sure to adjust the degrees of the visual angle when  
installing your camera.  
CAMERA ID  
OFF  
BACKLIGHT  
WDR  
WHITE BAL.  
W-ATW  
• If you increase WDR level, unnatural phenomenon may appear.  
2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.  
WDR: In case that bright and dark parts exist on the screen at the same time,  
your camera allows you to see both parts clearly  
BLC: When the image is in front of strong background lighting, your camera  
allows you to get the clear image  
WHITE BALANCE CONTROL  
Your camera provides 4 ‘WHITE BAL.’ control modes. You can select the most  
suitable one. You can adjust the white balance.  
OFF: Deactivation  
1. Press the SET button to display the SETUP menu and move the arrow indicator  
to 'WHITE BALANCE' using the UP or DOWN button.  
2. Set WHITE BAL.’ to the desired mode using LEFT or RIGHT button.  
SETUP  
WDR  
BLC  
OFF  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
WDR  
3. Press the ‘SET’ button.  
When WDR’ is chosen, you can adjust the level.  
W-ATW  
OFF  
LEVEL  
WDR SET  
The six WHITE BALANCE control modes are as follows :  
LEVEL  
PRESS SET TO RETURN  
You can select the level from -4 to 4. WDR sensitivity is increased or decreased.  
0
W-ATW(Wide Auto Tracking White balance):  
When color temperature is 2400~12000K, select this mode. (EX. a fluorescent  
lamp, outdoor)  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
20  
21  
Operating Your Camera  
S-ATW(Special Auto Tracking White balance): When color temperature is  
1800~6000K, specially in sodium lamp, select this mode. (EX. sodium lamp,  
inside the tunnel)  
2. Set MOTION DET.’ to the desired mode using LEFT or RIGHT button.  
SETUP  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
WDR  
AWC(Auto White balance Control): The white balance is automatically  
adjusted in a specific environment. In order to obtain the best result, press the SET  
button while the camera focuses on white paper. If the environment including the  
light source is changed, you have to adjust the white balance again.  
W-ATW  
OFF  
LEVEL  
OFF  
SHUTTER  
MANUAL : To fine adjust, select the Manual mode. You can increase or  
decrease the red or blue factor while monitoring the difference on the screen.  
Set to 'MANUAL' mode and press the SET button. Increase or decrease the  
value for RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and  
press the SET button when you obtain the best color.  
MD1: Your camera detects the object’s motion by outline or difference of a  
color tone, so this mode is very useful for the daytime or observing  
small moving object.  
Press SET button.  
Not es  
Proper White Balance may not be obtained under the following conditions, in these  
cases select the AWC mode.  
When the scene contains mostly high color temperature object, such as a blue  
sky or sunset.  
When the scene is dim.  
If your camera faces fluorescent lamp directly or is installed in the place of the  
changing illumination.  
Move the arrow indicator to ‘AREA SET’ using UP and DOWN button, and  
then press the SET button.  
Set the areas you want to observe.  
· You can adjust the top, bottom, left and right base lines by 13 steps from top to  
bottom, 18 steps from left to right with an increment of 1.  
MOTION DETECTION  
Whenever your camera detects motion of object displaying ‘MOTION DETECTED’  
with the number counted up on the screen.  
1. Press the SET button to display the SETUP menu and move the arrow  
indicator to 'MOTION DET.' using the UP or DOWN button.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
22  
23  
Operating Your Camera  
· Move the arrow indicator to 'TOP' using the UP or DOWN button and increase or  
decrease the value using the LEFT or RIGHT button. Repeat the procedure for  
bottom, left and right.  
Tips on Using the Motion Detection Feature  
As you increase or decrease MD LEVEL, the areas’ sensitivity is increased or  
decreased for object.  
18  
6
After selecting zone and sensitivity, perform a test operation to make sure it  
works properly.  
• If the lighting flickers, the motion detection feature might not work properly.  
13  
5
The object should occupy 10% or more of its zone. The bigger the object, the  
higher sensitivity.  
• If the brightness of an object changes rapidly by sudden lighting change, the  
camera may detect it as a motion.  
Maximum  
Minimum  
· When completed, press SET button.  
Your camera can count up to 999. If you reset your camera with selecting  
RESET’ in SPECIAL menu or turn it off and on, your camera’ll count up from 0.  
MD2: Your camera detects object’s motion by the variation of brightness, so  
this mode is very useful for night or observing large moving object.  
Also MD2 enables you to set seperated areas.  
When this feature is activated, another algorithm may take more time to be operated.  
This system does not guarantee prevention of fires or thefts. The manufacturer  
is not responsible for any accident or damage.  
Press SET button.  
Move the arrow indicator to ‘AREA SET’ like MD1.  
Set the areas you want to observe of the 48 areas.  
IRIS LEVEL CONTROL  
You can control the brightness of the screen.  
1. Press the SET button to display the setup menu and move the arrow indicator  
to 'IRIS' using the UP or DOWN button and press SET button.  
2. Set LEVEL’ to the desired brightness using LEFT or RIGHT button.  
· Move the cursor to the area you want to observe, and then press the SET button.  
· After setting, move the cursor to edge in any direction and then press the button  
just one more, let ‘END’ blink.  
SETUP  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
WDR  
· Press the SET button.  
W-ATW  
OFF  
Not es  
LEVEL  
OFF  
SHUTTER  
If you set some areas of 48 areas, your camera detects the object’s motion within  
the areas you set.  
3. When completed move the arrow indicator to ‘END’ and press the SET button.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
24  
25  
Operating Your Camera  
4. When completed, press the SET button.  
SHUTTER SPEED CONTROL  
You can control brightness of the screen by the shutter speed.  
1. Press the SET button to display the setup menu and move the arrow indicator  
to SHUTTER’ using the UP or DOWN button.  
Not es  
For effective 1/100(1/120) mode set WDR mode in BACKLIGHT menu to OFF.  
1/100(1/120) mode is not effective with WDR mode.  
• If you choose MANUAL mode, you can’t use WDR mode in ‘BACKLIGHT’ menu.  
• If you select MANUAL mode, SENSE UP is not operated.  
2. Set SHUTTER’ to the desired mode using the LEFT or RIGHT button.  
OFF: Deactivation  
1/100(1/120: PAL Models): Flickerless mode (When WDR is on, the image  
can flicker a little)  
MANUAL: When setting shutter speed manually  
SENSE UP  
SETUP  
You can always get the clear image with this function under night or low-  
lighting level.  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
WDR  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
1. Press the SET button to display the setup menu and move the arrow  
indicator to 'SENSE UP' using the UP or DOWN button.  
2. Set SENSE UP’ to the desired mode using the LEFT or RIGHT button.  
AUTO: When your camera is under night or low-lighting level, select this  
AGC-L  
mode.  
OFF: Deactivation  
3. If you choose ‘MANUAL’, select the optimal shutter speed.  
You can select speed from ‘1/60’ to ‘1/200,000’sec (NTSC Models), ‘1/50’ to  
‘1/200,000’sec (PAL Models).  
SETUP  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
WDR  
When the shutter speed is increased or decreased using the LEFT or RIGHT  
button, you can find the difference by monitoring the brightness of the  
screen.  
W-ATW  
OFF  
LEVEL  
OFF  
SHUTTER  
SENSE UP  
GAIN  
OFF  
MANUAL SET  
VALUE : 1/60  
MANUAL SET  
VALUE : 1/50  
AGC-L  
MIDDLE  
SSNR  
SPECIAL  
EXIT  
PRESS SET TO RETURN  
PRESS SET TO RETURN  
NTSC Models  
PAL Models  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
26  
27  
Operating Your Camera  
MIDDLE: middle reduction of the noise  
GAIN  
HIGH: high reduction of the noise  
OFF: Deactivation  
To get brighter picture.  
1. Press the SET button to display the setup menu and move the arrow indicator  
to GAIN’ using the UP or DOWN button.  
SETUP  
CAMERA ID  
OFF  
2. Set gain’ to desired mode using the LEFT or RIGHT mode.  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
WDR  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
AGC-H: Gain is increased or decreased from 0 to 30dB automatically as  
following the illumination.  
AGC-L: Gain is increased or decreased from 0 to 27dB automatically as  
following the illumination.  
AGC-L  
MIDDLE  
OFF: Deactivation  
SSNR  
SPECIAL  
EXIT  
SETUP  
CAMERA ID  
OFF  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
IRIS  
SHUTTER  
SENSE UP  
GAIN  
WDR  
W-ATW  
OFF  
LEVEL  
OFF  
OFF  
Not es  
• If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is increased as well  
as noise on the screen.  
Afterimage may appear with SSNR.  
AGC-L  
MIDDLE  
SSNR  
SPECIAL  
EXIT  
SSNR(Samsung Super Noise Reduction)  
To reduce the noise on the screen.  
1. Press the SET button to display the setup menu and move the arrow indicator  
to SSNR’ using the UP or DOWN button.  
2. Set SSNR’ to desired mode using the LEFT or RIGHT mode.  
LOW: low reduction of the noise  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
28  
29  
Operating Your Camera  
Not es  
SPECIAL  
When the power frequency is 50Hz, you can not use line-lock mode(NTSC Models).  
When the power frequency is 60Hz, you can not use the line-lock mode(PAL Models).  
• ‘Sync.’ mode is fixed to ‘INT’ in DC 12V input power.  
PRIVACY: To mask area which you want to mask  
- OFF: Deactivation  
- ON: Privacy mode activated  
1.Press the SET button to display the setup menu and move the arrow indicator to  
‘SPECIAL’ using the UP or DOWN button.  
· Press the SET button.  
2. Press the SET button.  
COLOR : choose color or B/W mode  
- ON : color mode  
- OFF : B/W mode  
- AUTO1 : generally color mode, B/W mode in low luminance.  
- AUTO2 : AUTO2 is identical with AUTO1 under SENSE UP : AUTO condition.  
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and  
EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronizes the  
video signal between cameras without a synchronous generator.  
The line-lock synchronization is only used in the areas of 60Hz  
(NTSC Models) / 50Hz (PAL Models).  
- INT : Internal synchronization  
- OFF : External line-lock synchronization  
· Move the arrow indicator to area you want to mask.  
· Set ON’ using LEFT or RIGHT button.  
· Press the SET button and then set the areas bounds with the method like  
MD1 Set. (see page 23)  
· When completed, press the SET button.  
RESET: To reset your camera to factory default condition  
END: To move Top-menu  
· If you choose ‘L/L, you can adjust the desired phase. Press the SET button.  
-You can adjust the desired phase from 0 to 270.  
EXIT: To finish setting menu  
LINE LOCK  
PHASE : 225  
PRESS SET TO RETURN  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
30  
31  
Troubleshooting  
If you have trouble operating your camera, refer to the following table. If the  
guidelines do not enable you to solve the problem, contact an authorized  
technician.  
Problem  
Solution  
The color of the picture  
is not matched.  
Check that you have properly set the WHITE BAL.’  
menu. (refer to page 21)  
Problem  
Solution  
The image on the screen  
flickers.  
Is the camera facing to direct sunlight or fluoresent  
lighting? Change the camera position.  
Nothing appears on  
the screen.  
Check that the power cord and line connection  
between the camera and monitor are fixed properly.  
Check that you have properly connected VIDEO  
cable to the camera VIDEO output jack.  
Have you connected your camera to DC power  
source? Connect it to AC power source.  
L/L mode isn’t able to  
be selected.  
The image on the  
screen is dim.  
Is lens stained with dirt? Clean your lens with soft,  
clean cloth.  
Set the monitor to proper condition.  
If the camera is exposed to too strong light, change  
the camera position.  
Adjust the lensfocus properly.  
The image on the  
screen is dark.  
Adjust the contrast feature of the monitor.  
If you have an intermediate device, set the 75/ Hi-z  
properly. (refer to page 13)  
The camera is not  
working properly, and  
the surface of the  
camera is hot.  
Check that you have properly connected the camera  
to an appropriate power source.  
Have you set MOTION DET.menu to OFF?  
Have you set MD LEVELto too low?  
Have you set MD AREAproperly?  
MOTION DETECTION  
function is not active.  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
32  
33  
Dimension  
Specifications  
Ø 148mm  
SVD-4120AN  
SVD-4120AP SVD-4120AWN SVD-4120AWP  
Item  
Power Source  
DC 12V / AC 24V compatible  
280mA(DC) / 3.8W(AC)  
Power Consumption  
Image Sensor  
1/3”, Vertical double density interline CCD  
Total Pixels  
811(H)x508(V), 1/3”CCD 759(H)x596(V), 1/3”CCD 811(H)x508(V), 1/3”CCD 759(H)x596(V), 1/3”CCD  
768(H)x494(V), 1/3”CCD 752(H)x582(V), 1/3”CCD 768(H)x494(V), 1/3”CCD 752(H)x582(V), 1/3”CCD  
Effective Pixels  
LENS TYPE  
2.5X Vari-Focal,f=3.8~9.5  
1:1.3~2.0  
2.4X Vari-Focal,f=2.5~6.0  
1:1.3~1.9  
Maximum Aperature Ratio  
Angle of View  
126mm  
H: 74.2˚~30.0˚, V: 54.0˚~22.4˚, D: 96.8˚~37.4˚  
H: 108.2˚~47.6˚, V: 80.4˚~35.6˚, D:136.6˚~59.4˚  
Scanning System  
2:1 Interlaced 525  
2:1 Interlaced 625  
2:1 Interlaced 525  
2:1 Interlaced 625  
Lines/60Fields/30Frames Lines/50Fields/25Frames Lines/60Fields/30Frames Lines/50Fields/25Frames  
Internal / Line Lock selectable  
Synchronization  
Video Output  
1.0V[p-p]NTSC composite, 1.0V[p-p]PAL composite, 1.0V[p-p]NTSC composite, 1.0V[p-p]PAL composite,  
75W/BNC Connector  
75W/BNC Connector  
75W/BNC Connector  
75W/BNC Connector  
Resolution  
500TV Lines  
Wide Dynamic Range  
Gain Control  
ON / OFF / AUTO  
85mm  
AGC-L, AGC-H, OFF selectable  
Electric Shutter Speed  
SENSE UP  
1/60~1/200,000sec  
1/50~1/200,000sec  
1/60~1/200,000sec  
1/50~1/200,000sec  
Built-in(selectable limit~X128)  
DC Drive  
IRIS MODE  
WHITE BALANCE  
Min. Illumination  
S/N(Y signal)  
W-ATW / S-ATW / AWC / MANUAL  
0.003Lux(Sense Up) / 0.3Lux(F1.3)  
50dB (Weight ON)  
83.5mm  
Motion Detection  
O.S.D  
MD1 / MD2 / OFF  
Built-in  
SSNR  
LOW / MIDDLE / HIGH /OFF  
ON / OFF(4 Programmable Zone)  
-10˚C ~ +50˚C (14˚F ~ 122˚F)  
30% ~ 90% RH  
PRIVACY Function  
Operating Temperature  
Operating Humidity  
Dimension(mm)  
Weight(W/O Lens & Power Cord)  
Angle  
f150(W) x 130(H)  
1.4kg  
Panning : 340˚ , Tilt : 70˚  
85mm  
* Design and specifications are subject to change without notice  
Users MDanouawl nload from Www.Somanuals.com. All Manuals Search And DCoOwLOnRlDoOaMdE .CAMERA  
COLOR DOME CAMERA  
Users Manual  
34  
35  
DECLARATION OF CONFORMITY  
M E M O  
Application of Council Directive(s)  
89 / 336 / EEC  
Manufacturer's Name  
Manufacturer's Address  
SAMSUNG TECHWIN CO., LTD  
SAMSUNG TECHWIN CO., LTD  
42, SUNGJU-DONG CHANGWON-CITY,  
KYUNGNAM, KOREA, 641-120  
European Representative Name  
European Representative Address  
Equipment Type/Environment  
Model Name  
CCTV Camera  
SVD-4120A/AW  
Beginning Serial NO.  
S4100002  
Year of Manufacture  
2004. 1. 2  
Conformance to  
EN 50081-1 : 1992  
EMC-Directive 89/336 EEC and 92/31/EEC  
EN 50130-4 : 1996  
We, the undersigned, here by declare that the equipment specified above conforms  
to the above Directive(s).  
Manufacturer SAMSUNG TECHWIN CO., LTD  
Signature  
Legal Representative in Europe  
Signature  
Full Name  
Position  
Place  
Full Name  
Position  
Place  
YOUNG TAEK SON  
QUALITY CONTROL MANAGER  
CHANGWON, KOREA  
2004. 1. 2  
Date  
Date  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M E M O  
M E M O  
Download from Www.Somanuals.com. All Manuals Search And Download.  

RCA Flat Panel Television R52WM24 User Guide
RCA Headphones WHP150 User Guide
Runco Flat Panel Television XP 50 User Guide
Samsung Camcorder 07660 2112 User Guide
Samsung Cell Phone C414 User Guide
Samsung Flat Panel Television 400DX 3 User Guide
Sanyo Battery Charger UF 811 User Guide
Sanyo Vacuum Cleaner SC B1230 User Guide
Saris Bike Rack 2 bike User Guide
SECO LARM USA Garage Door Opener SD C141S User Guide