INSTALLATION/OPERATION MANUAL
XP-50
XP-OPAL50
XP-65
XP-OPAL65
High Definition, 1080p Flat Panel Plasma Displays
with
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare™ Standard Two Year Limited
Warranty
Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years
of unparalleled video performance.
This RuncoCare Standard Limited Warranty is provided free of charge by Runco International with the purchase of a covered
Runco product. The following sets forth Runco’s Standard Limited Warranty applicable to all Runco projectors, processors,
1
LCD and plasma display products, with the exception of the following models: XP-103DHD, SC-1, SC-1a and VW-100HD .
The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us, Runco
International and you, the customer who has purchased a Runco product. This contract applies to purchases of covered
Runco products occurring on or after September 1, 2008. Runco reserves the right to change the terms of this contract, and
such changes shall apply to purchases of covered Runco products that occur on or after any future effective date.
RuncoCare Standard Features
• Two-year protection from defects in material and workmanship
• Access to 24x7 phone support
• Complimentary, second-day one-way shipping
Warranty Coverage
Runco warrants its products to be free from defects in material and workmanship during the warranty period provided below.
If, in Runco’s determination, a product proves to be defective in material or workmanship during the warranty period, Runco
will repair the product, replace the product with a similar new or like new product, or refund a prorata share of the purchase
2
price (calculated based on the remainder of the warranty period and the then-current MSRP of a similar product), if repair or
replacement of the product is determined by Runco to not be feasible.
Length of Warranty
Runco products are warranted for two (2) years from the date of shipment from Runco. Lamps are warranted six (6) months
from the date of shipment or 1000 hours, whichever comes first. All other accessories, which includes, but is not limited to,
cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product, are warranted for ninety (90)
days from the date of shipment. Repaired product or replacement lamp is subsequently warranted for the remaining portion (if
any) of the original warranty term or 90 days from the date the product was shipped to you, whichever is longer.
Eligibility
This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an
authorized Runco dealer or distributor. This warranty is not transferable. You may be required to provide proof of purchase in
order to receive warranty services.
1. Runco may update this list of products excluded from this warranty from time to time at Runco’s sole discretion, but updates to
the list of covered products will not apply on a retroactive basis.
2. MSRP is defined as the most recent product price listed on Runco’s price list.
CinemaWall Installation/Operation Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare Claim Procedure
In the event of a product defect, please follow the warranty claim procedure provided below:
1. The Customer is required to contact a Runco dealer or Runco Technical Support via E-mail at [email protected] or via
in Europe for product service.
2. Be prepared to provide the date of purchase, the place of purchase, serial number, product model number, description of
the problem and troubleshooting steps already attempted.
3. Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem. If Runco is
unable to fix the problem to the customer’s satisfaction, Runco will issue a Return Material Authorization (RMA) if it is
determined that the claim was made within the coverage period of the Standard Limited Warranty.
4. The customer will need to return the defective product to the Runco repair depot location specified by the Runco technical
support representative. The customer will need to properly package the defective product, consisting of the product only,
and not include any accessories (e.g., cables, remotes, carrying cases, lens, lens cap and other peripherals) and return it
to the Runco repair depot specified by the technical support representative. It is the customer’s responsibility to properly
package the hardware, include all appropriate materials, and return it to the location specified by the Runco technical
support department. The customer will need to address and resolve any shipping damage claims directly with the shipping
company.
5. The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot.
Boxes may be purchased from a Runco technical support representative.
6. The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot.
7. Runco will pay freight charges to return the repaired/replacement product to the customer from the Runco repair depot.
8. Once an RMA has been created, the customer may contact [email protected] for follow-up questions or
confirmation status of the claim process.
Warranty Exclusions
This RuncoCare Standard Limited Warranty does not include or is limited by the following:
1. Products not purchased from an authorized Runco dealer
2. Rental costs incurred by the customer in the event of product defect or failure
3. Any product with a defaced, modified, or removed serial number
4. Damage, deterioration, or malfunction resulting from:
a Accident, abuse, misuse, neglect, improper ventilation, fire, water, disaster, lightning, or other acts of nature, smoke
exposure (cigarette or otherwise), unauthorized product modification (including use of an unauthorized mount), or failure
to follow instructions supplied with the product
b Repair or attempted repair by anyone not authorized by Runco
c Any damage to the product due to shipment
d Removal or installation of the product
e Causes external to the product, such as electric power fluctuations or failure
f Use of supplies or parts not meeting Runco’s specifications
g Normal wear and tear
h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed
i
Customer caused defects, including but not limited to, scratched/defaced/altered plastics
iv
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
j
Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for
regular cleaning of the product
k Opening the product and/or tampering with internal circuitry
Products lost, stolen or discarded
l
m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be
the result of customer use patterns
n Any other cause, which does not relate to a product defect in material or workmanship
5. Removal, installation, and setup service charges are excluded from this Standard Limited warranty
6. Runco’s warranty does not cover black uniformity issues or other LCD issues associated with usage outside the Runco
recommended guidelines and specifications for the product
7. Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver
to PO Box and FPO Box addresses
Extended Service Options
Runco offers extended and expanded service plans. For information on additional product protection, please E-mail
[email protected] or call (toll free) 800-23RUNCO (800-237-8626).
Online Product Registration
Limitation of Implied Warranties
RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLIED, EXCEPT THOSE EXPRESSLY PROVIDED HEREIN. RUNCO
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
CinemaWall Installation/Operation Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Exclusion of Damages
RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT.
1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS,
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR
OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
2. RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR OTHERWISE.
3. RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of Local Law
This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities
do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the
above limitations and exclusions may not apply to you.
COPYRIGHT AND TRADEMARKS:
© Copyright 2009 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright,
trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of Runco.
The trademarks reproduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are
licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco.
Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents
Pending.
vi
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Thank you for your purchase of this quality Runco product! For best performance, please read this manual carefully as it is your
guide through the menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
11. Only use the attachments/accessories specified by Runco.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
CinemaWall Installation/Operation Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance Information
DECLARATION OF CONFORMITY:
Manufacturer’s Name: Runco International, LLC
Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992
hereby declares that the products Model Numbers:
XP-50, XP-OPAL50, XP-65 and XP-OPAL65
conform with the provisions of:
Council Directive 2004/108/EC on Electromagnetic Compatibility;
EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment”
1998;
EN 55024 “Limits and methods of measurements of immunity characteristics of information technology equipment” 1998;
Including:
• EN 61000-4-2 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2:
Electrostatic discharge immunity test”
• EN 61000-4-3 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated,
Radio-Frequency, Electromagnetic Field Immunity Test”
• EN 61000-4-4 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 4: Electrical
fast transient/burst immunity test”
• EN 61000-4-5 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 5: Surge
immunity test”
• EN 61000-4-6 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 6: Conducted
disturbances induced by radio-frequency fields immunity test”
• EN 61000-4-8 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 8: Conducted
disturbances induced by power frequency magnetic fields immunity test”
• EN 61000-4-11 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 11: Voltage
dips, short interruptions and voltage variations immunity tests”
And:
• EN 61000-3-2 “Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment
input current up to and including 16 A per phase)” 2000;
• EN 61000-3-3 “Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage
fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A
and not subject to conditional connection” 1995;
Council Directive 2006/95/EC and amended by M1 and C1 on Low Voltage Equipment Safety;
EN 60950 “Safety of information technology equipment, including electrical business equipment”
The Technical Construction file required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc.,
1195 NW Compton Drive, Beaverton, OR 97006.
Date of Declaration: September 2009
viii
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC PART 15:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA (ICES-003):
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IMPORTANT RECYCLE INSTRUCTIONS
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be
hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws.
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European
Union and other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not be treated as
household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences to the environment and human health, which could
otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve
natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please
contact your local authorities or dealer and ask for the correct method of disposal.
CinemaWall Installation/Operation Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
x
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
RuncoCare™ Standard Two Year Limited Warranty ...................................................iii
Compliance Information .............................................................................................. viii
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
If You Have Comments About This Manual.............................................................1
Parts List ...............................................................................................................4
2. Controls and Functions ............................................................................................5
CinemaWall at a Glance ...............................................................................................5
CinemaWall Remote Control ........................................................................................9
3. Installation ...............................................................................................................11
Notes on Batteries................................................................................................11
Quick Setup ...............................................................................................................12
Ventilation.............................................................................................................14
Other Considerations............................................................................................15
Connections to the CinemaWall .................................................................................16
RS-232 Controller Connection..............................................................................19
CinemaWall Installation/Operation Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation .................................................................................................................21
Setting the Day and Time ...........................................................................................21
Selecting an Input Source ..........................................................................................23
Using Picture-In-Picture (PIP) .....................................................................................26
Using the On-Screen Menus ......................................................................................27
POS./SIZE............................................................................................................35
5. Maintenance and Troubleshooting ........................................................................53
6. Serial Communications ..........................................................................................55
RS-232 Connection and Port Configuration ...............................................................55
7. Specifications ..........................................................................................................63
CinemaWall Specifications .........................................................................................63
APPENDIX A. Default Settings ...................................................................................A-1
xii
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
3-2. HDMI Source Connections.........................................................................................16
3-7. AC Power Connection................................................................................................20
CinemaWall Installation/Operation Manual
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Notes:
xiv
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This Owner’s Manual describes how to install, set up and operate a Runco CinemaWall
Flat-Panel Plasma Display Monitor (Model XP-50, XP-OPAL50, XP-65 or XP-OPAL65).
1.1
About This Manual
Throughout this manual, the Runco CinemaWall Flat-Panel Plasma Display Monitor is
referred to as the “CinemaWall.” Except where otherwise indicated, the information in this
manual applies to all CinemaWall models.
Runco has prepared this manual to help home theater installers and end users get the
most out of the CinemaWall.
Target Audience
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
If You Have Comments
About This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Textual and Graphic
Conventions
• Remote control button identifiers are set in upper-case bold type; for example, “Press
EXIT to return to the previous menu.”
• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Letterbox, send the command DAM:ZOOM.”
• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc>
and <Tab>.
• <Enter>indicates that you may press either the RETURN or ENTER key on your
computer keyboard if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
A carriage return must be used after each command or string.
Note
CinemaWall Installation/Operation Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or
death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
... Turn to page:
Information about obtaining service
General information about the CinemaWall
Flat-Panel Plasma Display Monitor
Installation instructions
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Specifications for the CinemaWall Flat-Panel
Plasma Display Monitor
2
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The CinemaWall Flat-Panel Plasma Display Monitor takes picture quality to a whole new
level, boasting our brightest picture, best contrast ratio, deepest black levels and most
spot-on high definition colorimetry ever! In addition, sophisticated 16-bit digital video
processing, a new milestone, results in 4096 steps of graduation for seamless images
completely devoid of the primitive “solarization” and “stair stepping” characteristics
previously plaguing digital flat panel displays.
1.3
Description, Features
and Benefits
The CinemaWall features all of the Runco technologies you have come to expect from the
World's Finest Home Theater Products. Discrete, multiple aspect ratio control includes
VirtualWide™ for viewing 4:3 content in widescreen without appreciable picture
degradation, as well as ISF(ccc) calibration modes to easily maintain ISF standards. The
automation interface includes RS-232 control with discrete aspect ratio, input and power
on/off selection.
The CinemaWall not only represents a leap forward in high definition flat-panel technology,
but our engineering advances in plasma design ensure that it will enjoy a long life in any
installation, with operation extending to as much as 60,000 hours. At less than 4-1/4
inches thin, the CinemaWall provides unlimited installation flexibility as well.
The CinemaWall offers these key features and benefits:
• 16:9 Native Resolution: 1920 x 1080
Key Features and Benefits
• Models XP-OPAL50 and XP-OPAL65 feature Runco-exclusive Optical Path Alignment
(OPAL) technology, which delivers extreme glare reduction and enhanced contrast for
high ambient light environments
• Multiple Aspect Ratios with VirtualWide™ Mode
• Less than 4-1/4 inches thin
• High-altitude compliant to 9,000 feet
• Exceptional detail and artifact-free video enhancement
• ViVix™ video processing with 3:2 film detection circuitry
CinemaWall Installation/Operation Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Your CinemaWall is shipped with the following items. If any items are missing or damaged,
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.
➤
• CinemaWall Flat-Panel Plasma Display Monitor
• AC Power Cord
• Remote Control Unit and two (2), AA-size batteries
• CinemaWall Installation/Operation Manual (this document)
Optional Accessories – XP-50 and XP-OPAL50:
• Wall Mount Kit (part number 956-0081-00)
• Table Stand (part number 956-0082-00)
Optional Accessories – XP-65 and XP-OPAL65:
• Wall Mount Kit (part number 956-0103-00)
• Table Stand (part number 956-0105-00)
4
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Controls and Functions
2.1
CinemaWall at a
Glance
Controls and Indicators
(behind
front bezel)
2
4
3
1
Figure 2-1. CinemaWall XP-50 and XP-OPAL50 Front-Panel Controls and
Indicators
3
4
2
(behind
front bezel)
1
Figure 2-2. CinemaWall XP-65 and XP-OPAL65 Front-Panel Controls and
Indicators
CinemaWall Installation/Operation Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DISPLAY STAND
Optional accessory for table-top installations.
2. POWER BUTTON
Connects or disconnects the display panel from the AC power source.
3. STANDBY/ON INDICATOR
- Lights solid green to indicate normal operation;
- Flashes green to indicate that a Power-On Screen delay has been set (waiting to
power up);
- Lights orange to indicate that the PC INPUT is currently selected and the power
management function is active (no signal present);
- Lights red to indicate that the CinemaWall is in standby mode.
4. REMOTE CONTROL SENSOR
Receives the signals from the remote control.
6
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-3 shows the rear-panel connector locations on the CinemaWall.
Connectors
XP-50 / XP-OPAL50
6
XP-65 / XP-OPAL65
6
A
B
A
B
R
AUDIO
L
PR/CR/R
PB/CB/B
Y/G
AUDIO
AV IN
AV IN
COMPONENT/RGB IN
SLOT1
SLOT2
SLOT3
PC IN
SERIAL
1
2
3
4
5
Figure 2-3. CinemaWall Rear Panel
1. SLOT 1 (Dual HDMI input)
Two, HDCP-compliant digital video inputs.
2. SLOT 2 (Dual HDMI input)
Two, HDCP-compliant digital video inputs.
CinemaWall Installation/Operation Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. SLOT 3 (COMPONENT/RGB input)
Video/audio input (3 x BNC, 2 x RCA) for connecting either RGB (with sync on green)
or component high-definition television signals.
4. PC IN
Provides a 15-pin VGA connection and a 3.5-mm, stereo audio connection to a
personal computer. The CinemaWall automatically detects the signal resolution.
5. SERIAL
A male, 9-pin D-sub connector for interfacing with a PC or home theater
automation/control system.
6. POWER INPUT
Connect the CinemaWall to AC power here.
8
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-4 shows the CinemaWall remote control and describes its functionality.
2.2
CinemaWall Remote
Control
SURROUND button
Press the SURROUND button to turn surround-sound mode on or off.
ON
OFF
Note:
The surround settings are memorized separately for each AUDIO MENU setting
(STANDARD, DYNAMIC, CLEAR).
SURROUND
ON
ACTION button
Press ACTION to confirm a menu
selection.
OFF TIMER button
The CinemaWall can be preset to
switch to stand-by after a fixed
period. The setting changes to
30 minutes, 60 minutes, 90 minutes
and 0 minutes (off timer cancelled)
each time the button is pressed.
ASPECT button
Press this button repeatedly to select an
aspect ratio.
POWER button
30
60
90
The CinemaWall must first be plugged into
the wall outlet and turned on at the power
switch.
Press this button to turn the CinemaWall
on from Standby mode. Press it again to
put the CinemaWall into Standby mode.
0
When three minutes remain,
“OFF TIMER 3” appears on-screen.
The off timer is cancelled if a power
interruption occurs.
POS./SIZE button
Press this button to display the
POS./SIZE menu.
PICTURE button
Press this button to display the PICTURE
menu.
SET UP button
Press this button to display the
SET UP menu.
SOUND button
Press this button to display the
SOUND menu.
Volume Adjustment buttons
Press + or – to increase or decrease
the sound volume level.
MUTE
RESET
RETURN
Press this button to mute the sound.
Press again to reactivate sound.
Sound is also reactivated when power is
turned off or volume level is changed.
RETURN button
Press RETURN to return to the
previous menu screen.
RESET button
Press this button to restore settings for
the current menu to their factory- default
values.
RECALL button
Press RECALL to display the
current operating status:
Adjustment/Selection buttons
Use these buttons to select menu items
and adjust settings.
1
2
3
Input
Aspect Ratio
Off timer
The off timer indicator is displayed
only when the off timer has been set.
INPUT button
Press to select INPUT1A, INPUT1B,
INPUT2A, INPUT 2B, INPUT3 and PC
input slots sequentially.
Clock display
4
PC
4:3
1
2
MULTI PIP buttons
Use these buttons to control various
aspects of multi-PIP (picture-in-picture)
operation.
4
10:00
OFF TIMER 90
3
MOVE/ZOOM button
Press this button to change the PIP
window position or to display the
digital image zoom controls.
Figure 2-4. CinemaWall Remote Control
CinemaWall Installation/Operation Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
10
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
To install batteries in the remote control:
3.1
Remote Control
1. Press on the tab on the battery compartment cover and lift the cover in the direction
of the arrow.
2. Insert the included batteries. Ensure that the polarities correctly match the
markings inside the battery compartment.
and
3. Close the battery compartment cover and press the tab on the cover until it clicks in
place.
1
2
3
“AA” size
-
+
+
-
• When installing batteries, make sure that the battery polarities are correct.
• Do not mix an old battery with a new one or different types of batteries.
Notes on Batteries
• If you will not use the remote control for a long time, remove the batteries to avoid
damage from battery leakage.
• Do not drop the remote control or expose it to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. If that occurs, move the
plasma display away from the fluorescent lamp.
• Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the plasma display.
The signal from the remote control can be reflected by walls or
other surfaces.
Note
• If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
• Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the plasma display and repeat the operation.
CinemaWall Installation/Operation Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 gives a quick overview of the CinemaWall installation process. The sections
following this one provide detailed instructions.
3.2
Quick Setup
Installation must be performed by a qualified custom video
installation specialist.
Note
Table 3-1. Installation Overview
For Details, refer to
page...
Step
Procedure
1
2
3
Mount the CinemaWall on a wall or table stand
Connect signal sources to the CinemaWall
Connect external controller to CinemaWall SERIAL port
(optional)
4
5
Apply power to the CinemaWall
If using the CinemaWall with a computer, adjust computer
display properties
6
Display calibration: adjust the following for each input:
• Aspect ratio
• Picture Level
• Brightness
• Color level
• Tint
• Sharpness
• White Balance
12
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your CinemaWall will ensure the highest possible picture quality.
Whether you are installing the CinemaWall temporarily or permanently, you should take
the following into account to ensure that it performs optimally.
3.3
Installation
Considerations
Due to the design of all plasma glass panels made by every manufacturer, and the
interaction between ambient air pressure and the plasma gases contained inside of the
panel, reliable operation of your plasma display cannot be assured during operation at
certain high-altitude locations.
High-Altitude Operation
At higher elevations, each panel may react differently, depending upon the altitude, air
pressure, humidity and other meteorological factors. If you are planning to use this
product at a high-altitude location (above 9,000 feet), please contact Runco technical
support for further information.
To install the CinemaWall, you will need either an optional table stand or wall-mounting kit.
Mounting the CinemaWall
on a Wall or Table Stand
If you do decide to wall-mount the CinemaWall, ensure that the wall-mount bracket is
installed according to the instructions included with it. The wall must be capable of
supporting a redundant weight factor five (5) times the weight of the display, or be
reinforced.
Runco recommends that this be done by a custom installation specialist.
Use only a Runco-approved wall-mount kit, table stand or floor
pedestal that is specifically designed for your display. Refer to
Note
You can attach your optional mounts or stand to the CinemaWall in either of two ways:
• While it is upright.
CinemaWall Installation/Operation Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• As it lies flat with the screen face
down. Place the protective sheet,
which was wrapped around the
plasma monitor when it was
packaged, between the screen and
your work surface to avoid
scratching or otherwise damaging
the screen surface.
Ambient Light
Ventilation
In general, minimize or eliminate light sources directed at the display. Contrast ratio in your
images will be noticeably reduced if light directly strikes the display, such as when a shaft
of light from a window or floodlight falls on the image. Images may then appear washed
out and less vibrant.
➤
➤
If you are mounting the CinemaWall in an enclosure, leave sufficient space on all sides
maintaining the proper operating temperature.
Wall
50mm (2")
50mm (2")
Wall
50mm (2")
Figure 3-1. Ventilation Requirements for Enclosure Mounting
14
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are some other considerations and tips that can help improve your installation, avoid
damage and prolong operating life:
Other Considerations
• Keep the ambient temperature constant and below 35°C (95°F). Keep the display away
from heating and/or air conditioning vents. Changes in temperature may cause drifts in
the display circuitry, which may affect performance.
• Keep the CinemaWall away from devices that radiate electromagnetic energy such as
motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
• Handle the unit carefully when installing or carrying it. Use the built-in handles; DO NOT
touch or hold the screen face.
• Set the unit away from heat, excessive dust, and direct sunlight.
• Protect the inside of the unit from liquids and small metal objects. In case of accident,
unplug the power cord and have it serviced by an authorized Service Center.
• Do not hit or scratch the panel surface as this causes flaws on the surface of the
screen.
• For correct installation and mounting it is strongly recommended to use a trained,
authorized dealer.
• To avoid sulfurization, it is strongly recommended not to place the unit in a dressing
room in a public bath or hot spring bath.
CinemaWall Installation/Operation Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to connect the CinemaWall to your video sources, external controller(s)
– if present – and AC power.
3.4
Connections to the
CinemaWall
When connecting your equipment:
• Turn off all equipment before making any connections.
• Use the correct signal cables (sold separately) for each source.
• Ensure that the cables are securely connected. Tighten the thumbscrews on
connectors that have them.
Connecting Source
Components to the
CinemaWall
Connect your video sources to the CinemaWall as shown and described in the sections
that follow.
➤
HDMI Connections: The CinemaWall has four (4) HDMI video inputs for connecting a
BD/DVD player, DTV decoder or any other device with a DVI or HDMI output. Connect
Use the HDMI inputs whenever possible. This ensures the highest
Tip
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
into the display.
R
AUDIO
L
PR/CR/R
PB/CB/B Y/G
COMPONENT/RGB IN
SLOT1
SLOT2
SLOT3
PC
HDMI
AV OUT
HDMI
AV OUT
HDMI
AV OUT
HDMI
AV OUT
HDMI sources (BD, DVD, DTV Set-Top Box etc.)
Figure 3-2. HDMI Source Connections
16
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT VIDEO OUT
P
R
DVD
P
B
Y, PB, PR
OUT
,
DTV-Set-Top Box
(DTV-STB)
Y
RCA-BNC
adapter
plug
L
AUDIO
OUT
R
R
AUDIO
L
P
R/CR/R
PB/CB/B Y/G
COMPONENT/RGB IN
SLOT3
Computer
RGB Camcorder
or
Figure 3-3. RGB and Component Video Connections
1. Change the “COMPONENT/RGB-IN SELECT” setting in the
SET UP menu to “COMPONENT” or “RGB” according to the color
space used by the source.
Note
2. The CinemaWall supports only “sync-on-green” RGB signals on
this input. If your source outputs composite sync or separate
horizontal and vertical sync, connect it to the PC input.
CinemaWall Installation/Operation Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog (Computer) RGB Connections: The CinemaWall has an RGB input and a
signals compatible with the CinemaWall. Use with signals other
Note
than those listed may cause some functions not to work.
2. Some Macintosh computers may require a Macintosh video
adapter. Contact your nearest authorized service center or dealer.
3. The PC input supports the VESA Display Data Channel (DDC 2B)
standard. This standard provides “Plug and Play” capability; the
display and a VESA DDC-compatible computer communicate their
setting requirements, allowing for quick and easy setup.
In order for Plug and Play to work correctly, you must turn on the
CinemaWall before you turn on the connected computer.
4. This CinemaWall may not be able to display images from some
notebook computers in simultaneous (CRT/LCD) mode. Should
this occur, switch the notebook computer to “CRT only” mode. If
you are unsure how to do this, refer to your notebook computer’s
user manual.
(Female)
AUDIO
PC IN
Mini D-sub 15p
RGB
PC cable
(Male)
Conversion adapter
(if necessary)
Audio
Stereo plug
Connect a cable which matches
the audio output terminal on the computer.
Figure 3-4. Analog RGB Connections
18
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Use a straight-through RS-232 cable with a 9-pin male connector to connect a PC or
home theater control/automation system (if present) to the RS-232 port on the
RS-232 Controller
Connection
Personal Computer
(or Control/Automation System)
(Male)
SERIAL
RS-232C Straight Cable
9-pin
Connector Pin Assignments:
2
3
5
Receive Data
Transmit Data
Ground
1
2
3
4
5
6
7
8
9
1, 4, 6, 9
7, 8
Not Connected
(shorted together)
Figure 3-5. RS-232 Control System Connection
Connect the (positive) and (negative) speaker wires to the SPEAKER-R and
Connecting External
Speakers (Optional)
information, refer to the owner’s manual for your speakers.
1
2
1
Speaker
Terminal (R)
2
Speaker Terminal (R)
Figure 3-6. External Speaker Connection
CinemaWall Installation/Operation Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting AC Power
Plug the female end of the power cord into the AC receptacle on the rear of the
CinemaWall. Connect the other end to your AC power source.
➤
XP-50 / XP-OPAL50
XP-65 / XP-OPAL65
Figure 3-7. AC Power Connection
20
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation
1. Turn on your source components.
4.1
Turning on the Power
standby/on indicator lights green.
3. After a brief warm-up period (approximately five seconds), the CinemaWall will display
an image.
4. Press the POWER button on the remote
control to put the CinemaWall into standby
mode. The power indicator lights solid red.
5. Press the POWER button again to return to
normal operation.
The CinemaWall OSD language is initially set to English, but can also display the menus in
Russian, German, French, Italian or Spanish. To change the OSD language:
4.2
Changing the OSD
Language
2. Press
3. Press
or to select the desired language. The change takes effect immediately.
You can program the CinemaWall to perform various actions, such as turning on or off, at
specific times of the day and days of the week. In order to take advantage of this
capability, the CinemaWall internal clock must be set correctly. To do this:
4.3
Setting the Day and
Time
2. Press
or
3. Press the ACTION ( ) button.
4. Press
or
repeatedly to highlight DAY
to select the current day of
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99:99
in the menu.
SET
5. Press or
the week.
DAY
PRESENT TIME OF DAY
TUE
10:00
time of day.
RETURN
SET
SELECT
7. Press
or
repeatedly to highlight SET
in the menu, then press the ACTION (
)
button.
CinemaWall Installation/Operation Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To maximize image quality when using the CinemaWall with a personal computer, you
may need to adjust the display properties of your computer’s video card. To do this on a
Microsoft® Windows®-based PC:
4.4
Setting the Computer
Display Properties
1. Choose Settings from the Windows Start
Menu and click on “Control Panel.”
2. Double click on the Display icon.
3. Click the Settings tab on the display dialog
box.
4. Set the Screen area to 1024x768 pixels.
5. Click the Advanced button and click the
Monitor tab on the dialog box. Set the
Refresh Frequency to 60Hz and click
OK.
22
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. The native resolution of the CinemaWall is 1920 x 1080. Other
horizontal or vertical resolutions may be scaled upward or
downward to fit the display.
Note
2. With most computers, you can get the best picture at
1024 x 768 @ 60Hz.
To prevent image retention (burn) on your display, ALWAYS use a
screen saver and set it to the shortest possible time.
WARNING
To select an input source, press the INPUT button on
the remote control repeatedly.
4.5
Selecting an Input
Source
To change the aspect ratio (size and shape) of the
4.6
displayed image, press the ASPECT (
) button
Changing the Aspect
Ratio
repeatedly on the remote control.
Select the appropriate aspect ratio for the type of
Note that some aspect ratios are unavailable and/or not useful with certain types of
source material. The optimal setting depends on a number of factors, such as:
• The aspect ratio of the source material, as broadcast or encoded on the playback
medium.
• The “display type” (16:9 or 4:3) and output resolution settings at the source
component. Most modern DVD/BD players and set-top boxes have such controls.
• Viewer preference (original aspect ratio with “black bars,” or a full-screen presentation
with some distortion or cropping).
The aspect ratio selection is saved independently for each input.
Note
CinemaWall Installation/Operation Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Aspect Ratio Setting
(Note)
Input Image -> Displayed Image
Description
All Aspect All Aspect
= ON
= OFF
16:9 linearly scales the
source active image hori-
zontally and vertically to fill a
16:9 screen.
16:9
16:9
With standard-definition
(SD) signals, 4:3 images are
stretched horizontally to fill
the screen.
Letterbox pictures with a
14:9 aspect ratio are
enlarged vertically and hori-
zontally so that they fill the
screen vertically and are
slightly smaller than the
screen horizontally. The top
and bottom edges of the
image are cut off. Side pan-
els appear at the left and
right edges of the screen.
14:9
–
VIRTUALWIDE and
VIRTUALWIDE1 scale a 4:3
image NON-linearly (more
on the sides than in the
center) to fit a 16:9 screen.
With 16:9 images, the cen-
ter area is horizontally com-
pressed by a small amount.
VIRTUAL- VIRTUAL-
WIDE1
WIDE
VIRTUALWIDE2 scales a
16:9 image NON-linearly
(more on the sides than in
the center) to fit a 16:9
screen. The left and right
edges of the image are cut
off.
VIRTUAL-
WIDE2
–
Note: To make all of the aspect ratio selections listed here available to the viewer, set All Aspect in
24
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Aspect Ratio Setting
(Note)
Input Image -> Displayed Image
All Aspect All Aspect
Description
= ON
= OFF
4:3 (4:3(1)) linearly scales
the source image horizon-
tally and vertically to fill a 4:3
screen. Side panels are dis-
played at the left and right
edges of the screen.
4:3(1)
4:3
4:3(2) displays a 16:9
source image in its original
aspect ratio and masks the
left and right sides.
4:3(2)
FILL
–
FILL is similar to
VIRTUALWIDE2 (see
above), but employs a lin-
ear, horizontal stretch.
FILL
Note: This setting is not
available with SD signals.
LETTERBOX
(LETTERBOX1) scales
(zooms in on) a 4:3 image
linearly (by the same
amount on all sides) to fill a
16:9 display, cropping the
top and bottom of the
image.
LETTER- LETTER-
BOX1
BOX
16:9 images are vertically
scaled by a factor of
approximately 1.33, but the
width is unchanged.
LETTER-
BOX2
–
LETTERBOX2 scales
(zooms in on) a 16:9 image
linearly (by the same
amount on all sides) to fill a
16:9 display, cropping the
image on all sides.
Note: To make all of the aspect ratio selections listed here available to the viewer, set All Aspect in
the OPTIONS menu (described on page 51) to On.
CinemaWall Installation/Operation Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Aspect Ratio Setting
(Note)
Input Image -> Displayed Image
All Aspect All Aspect
Description
= ON
= OFF
LETTER-
BOX3
–
LETTERBOX2 scales
(zooms in on) a 2.35:1
image linearly (by the same
amount on all sides) to fill a
16:9 display, cropping the
image on all sides.
Select CINEMA to view
2.35:1 source material in its
native aspect ratio.
CINEMA masks the upper
and lower portions of the
screen to create a viewable
area with a 2.35:1 aspect
ratio.
CINEMA
CINEMA
The geometry of the active
image area is unchanged.
Note: To make all of the aspect ratio selections listed here available to the viewer, set All Aspect in
the OPTIONS menu (described on page 51) to On.
Use PIP to display an image from two sources at the same time in a variety of ways.
4.7
Using
Picture-In-Picture (PIP)
Activating PIP
To activate PIP, press the MULTI PIP (
) remote control button.
➤
➤
Swapping the Main and
PIP Images
Press SWAP (
) to replace the main image with the secondary sub-image and vice
versa.
[Picture and Picture]
Main picture Sub picture
[Picture out Picture]
[Picture in Picture]
Main picture
Sub picture Main picture Sub picture
B
A
A
A B
B
A
B
B
B A
A
26
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Press SELECT (
) to choose a target
Selecting a PIP Target
Main picture label is bright
Sub picture label is bright
screen (main or sub) for PIP operations.
Screen or Input Source
INPUT1A
PC
INPUT1A
PC
The audio signal associated with the target
screen is heard through the speakers.
A
A
B
B
Input modes switching is possible
Press INPUT ( ) to select an input to
display on the target screen (main or sub).
Main picture label is changed
Sub picture label is changed
INPUT1B
PC
INPUT1A
INPUT3
C
A
B
D
Picture is changed
To change the PIP window position, press
Changing the PIP Window
Position
MOVE/ZOOM (
) repeatedly until the window is in
the desired position.
The CinemaWall On-Screen Display (OSD) controls are
grouped into five (5) menus: POS./SIZE, PICTURE,
SOUND, SET UP and OPTIONS.
4.8
Using the On-Screen
Menus
The PICTURE, ADVANCED SETTINGS (in the
PICTURE menu), SET UP and OPTIONS menus
consist of multiple “pages,” to limit the amount of space
those menus occupy on the screen.
To access the POS./SIZE, PICTURE, SOUND or
SET UP menus, press the remote control button
corresponding to that menu. Press that same button
again to hide the menu.
To access the OPTIONS menu:
1. Press SET UP.
2. Press
or
3. Press and hold the SURROUND (
) button until the page 1 of the OPTIONS menu
appears (approximately four seconds).
• Press
• When navigating a multi-page menu (PICTURE,
SET UP or OPTIONS), the button takes you from
or
to highlight a menu item.
Menu Navigation
RESET
RETURN
the bottom of one menu page to the top of the next
one. Likewise, the button takes you from the top of
one menu page to the bottom of the previous one.
• Press
or
to change the selected setting.
• Some menu items lead to sub-menus containing
more options. Press the ACTION ( ) button to
access a sub-menu. To return to the previous menu, press RETURN.
CinemaWall Installation/Operation Manual 27
Download from Www.Somanuals.com. All Manuals Search And Download.
• The OSD menu closes after 60 seconds of inactivity.
The CinemaWall OSD menus are arranged hierarchically, as shown in Figure 4-1.
Depending on the selected input source and signal characteristics, some menu options
may not be available.
H-POS
H-SIZE
V-POS
V-SIZE
-124, -123 ... 0 ... 123, 124
-62, -61 ... 0 ... 61, 62
-32, -31 ... 0 ... 31, 32
DOT CLOCK
(INPUT3/PC INPUT only)
POS./SIZE
CLOCK PHASE
(INPUT3/PC INPUT only)
-16, -15 ... 0 ... 15, 16
1:1 PIXEL MODE
(1080i/1080p signals only)
ON / OFF
PICTURE MENU
PICTURE
STANDARD, ISF DAY, ISF NIGHT or MONITOR
BRIGHTNESS
COLOR
-30, -29 ... 0 ...29, 30
TINT
SHARPNESS
COLOR TEMP
COLOR MANAGEMENT
-15, -14 ... 0 ... 14, 15
NORMAL, COOL or WARM
ON/OFF
PICTURE
ADVANCED SETTINGS
(OFF)
--
BLACK EXTENSION
INPUT LEVEL
0, 1, 2 ... 8
-32, -31, -30 ... 0 ... 30, 31, 32
2.0, 2.2, 2.5 or S-CURVE
OFF/ON
GAMMA
ADVANCED SETTINGS
(ON)
AGC
R/G/B GAIN
-30, -29 ... 0 ...29, 30
R/G/B OFFSET
STANDARD, DYNAMIC or CLEAR
AUDIO MENU
BASS
MID
-15, -14, -13 ... 0 ... 13, 14, 15
TREBLE
SOUND
BALANCE
SURROUND
AUDIO OUT (PIP)
-30, -29, 28 ... 0 ... 28, 29, 30
ON/OFF
MAIN or SUB
SYNC
(PC INPUT only)
AUTO, ON G or VBS
OFF/ON
3:2 PULLDOWN
XGA MODE
(INPUT3/PC INPUT only)
1024x768, 1280x768 or 1366x768
SIGNAL
NOISE REDUCTION
OFF, MIN, MID or MAX
VIDEO NR (OFF, MIN, MID or MAX)
BLOCK NR (OFF, MIN, MID or MAX)
MOSQUITO NR (OFF, MIN, MID or MAX)
NOISE REDUCTION - ADVANCED
START
SCROLLING BAR ONLY, OVERLAY SCROLLING
BAR, WHITE SCREEN or NEGATIVE IMAGE
FUNCTION
MODE
ON, OFF, INTERVAL or TIME OF DAY
0:00 ... 23:59 / 0:00, 0:15, 0:30 ... 23:45
0:00 ... 23:59 / 0:00, 0:15, 0:30 ... 23:45
OFF, DARK, MID or BRIGHT
OFF, ON1 or ON2
START TIME/SHOW DURATION
FINISH TIME/SAVER DURATION
SIDE BAR ADJUST
WOBBLING
SCREENSAVER
SET UP
(1/2)
PEAK LIMIT
OFF/ON
COMPONENT/RGB IN SELECT
INPUT LABEL
COMPONENT or RGB
INPUT[n], VIDEO[n], COMPONENT[n], RGB[n],
DIGITAL [1A/1B/2A/2B], PC[n], DVD[n],
CATV[n], VCR[n], STB[n]
POWER SAVE
STANDBY SAVE
OFF/ON
POWER MANAGEMENT
AUTO POWER OFF
ENGLISH (US), Русский (RUSSIAN), Deutsch
(GERMAN), Français, (FRENCH), italiano
(ITALIAN) or Español (SPANISH)
OSD LANGUAGE
Figure 4-1. OSD Menu Structure for CinemaWall
28
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
ON/OFF
x2, x3, x4 or x5
MULTI DISPLAY SETUP
(Note: Must set
MULTI PIP SETUP -> DISPLAY
MODE to “-” (normal)
x1, x2, x3, x4 or x5
ON/OFF
A1, A2, A3, A4, A5, B1, B2 ... E3, E4, E5
ON/OFF
AI SYNCHRONIZATION
MULTI PIP
PIP, ADVANCED PIP, BLEND PIP
MULTI PIP = PIP:
- (normal), P IN P, P AND P, P OUT P
MULTI PIP = ADVANCED PIP:
- (normal) or 1-8
DISPLAY MODE
MULTI PIP = BLEND PIP:
- (normal), P IN P, FULL
MULTI PIP SETUP
TRANSPARENCY
TRANSPARENCY LEVEL
INSERT
ON/OFF
(2/2)
0%, 5%, 10%, 15% ... 95%, 100%
ON/OFF
INSERT LEVEL
1%, 2%, 3% ... 10%
ON/OFF
PORTRAIT SETUP
SEAM HIDES VIDEO
VIEWING AREA
PORTRAIT SETUP
(Note: Must set
MULTI PIP SETUP -> DISPLAY
MODE to “-” (normal)
ON/OFF
4:3 (SD sources only) or 16:9
1, 2, or 3
LOCATION
AI SYNCHRONIZATION
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
DAY
ON/OFF
ON/OFF
0:00, 0:01, 0:02... 23:58, 23:59
ON/OFF
SET UP TIMER
0:00, 0:01, 0:02... 23:58, 23:59
MON, TUE, WED, THU, FRI, SAT or SUN
0:00, 0:01, 0:02... 23:58, 23:59
On/Off
PRESENT TIME SETUP
PRESENT TIME OF DAY
Function
Monday, Tuesday ... Sunday
---, Program1, Program2, Program3 ... Program7
Program Select (1, 2 ... 7)
Command Select (01, 02, 03 ... 64)
Time (--:-- or 0:00 ... 23:59)
Weekly Command Timer
Program Edit
On/Off
Command Assign
Onscreen Display
Initial INPUT
Off, PC, INPUT1A, INPUT1B, INPUT2A,
INPUT2B or INPUT3
Initial VOL level
On (0, 1, 2 ... 63) or Off
Maximum VOL level
Off, PC, INPUT1A, INPUT1B, INPUT2A,
INPUT2B or INPUT3
INPUT lock
Button lock
Off, MENU&ENTER, On (n/a)
Off, User1, User2 or User3
Enable/Disable
OPTIONS
Remocon User level
Off-timer function
Initial Power Mode
ID select
Normal, On or Standby
0, 1, 2, 3 ... 99, 100
Remote ID
Serial ID
Display size
On/Off
Studio W/B
Studio Gain
Slot power
Off, Auto or On
Power On Screen Delay
Clock Display
All Aspect
Off or 1 ... 30 seconds
On/Off
Rotate
Serial Slot Select
Slot1, Slot2 or Slot3
CinemaWall Installation/Operation Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
quality.
➤
The CinemaWall has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards to
obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF-certified installation
technician.
All signal types require separate processing. Therefore, you need to calibrate each input
separately.
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Runco recommends using the following calibration tools for best
results:
• External test pattern source – Ovation Multimedia, Video Essentials or AVIA test DVD
(or equivalent).
• A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input that you are calibrating and proceed as
follows. Perform the adjustments in the order listed here.
PICTURE
1/2
RESET
PICTURE MENU
PICTURE
NORMAL
STANDARD
26
BRIGHTNESS
COLOR
0
0
TINT
SHARPNESS
0
5
RESET
RETURN
ADJUST
SELECT
PICTURE
2/2
COLOR TEMP
COLOR MANAGEMENT
ADVANCED SETTINGS
NORMAL
OFF
OFF
RESET
CHANGE
SELECT
RETURN
30
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE MENU: The CinemaWall provides four picture memories per input for storing
and recalling image quality settings. To store settings in a picture memory, highlight
MONITOR. The CinemaWall “remembers” any adjustments you make when you switch to
a different picture memory, then switch back.
Select the MONITOR mode to disable the CinemaWall’s
Tip
“brightness variation” function, which automatically controls the
display brightness according to the average brightness level and
peak brightness level of the input signal. MONITOR mode is useful
to content creators and viewers who prefer to see content as it was
created, without any brightness enhancement.
PICTURE: On your external test pattern source, select a stepped, gray-bar pattern like
Figure 4-2. Typical Gray Bar Pattern for Adjusting Picture Level (Contrast)
) buttons,
adjust the Picture level (contrast) to a point just below which the white rectangle starts to
increase in size.
MONITOR.
Note
CinemaWall Installation/Operation Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIGHTNESS: On your external test pattern source, select a PLUGE pattern. (PLUGE is
PLUGE pattern.
Below Black
Above Black
Figure 4-3. Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
buttons, adjust the brightness so that:
)
• The darkest black bars disappear into the background.
• The dark gray areas are barely visible.
• The lighter gray areas are clearly visible.
• The white areas are a comfortable level of true white.
• The image contains only black, gray and white (no color).
Brightness and Picture level controls are interactive. A change to
one may require a subtle change to the other in order to achieve
the optimum setting.
Note
32
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
blue filter, adjust the color saturation level until the outermost (gray and blue) color bars
appear to be a single shade of blue:
TINT: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image
color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color
bars (on either side of the green bar) appear to be a single shade of blue.
Like the brightness and contrast controls, the color and tint controls
are interactive. A change to one may require a subtle change to the
other in order to achieve the optimum setting.
Note
CinemaWall Installation/Operation Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
white edges around the transitions from black to gray and different sized lines in the
“sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
PICTURE menu. (Color temperature defines the “color of gray.”) The choices are
For most situations, the appropriate setting is NORMAL. COOL produces a “bluer”
picture; WARM a “warmer” picture with more pronounced red and orange hues.
set it to ON to have the CinemaWall automatically manage color balance. For more direct
control of color balance, set it to OFF.
to perform
the following picture quality adjustments:
brightness of the displayed image. Its effect is similar to a backlight control on an LCD.
compensate.
34
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
conditions. If excess ambient light washes out the image and it becomes difficult or
impossible to see details in dark areas, lower the gamma setting to compensate. This
will improve contrast while maintaining good details for blacks. Conversely, if the image
is washed out and unnatural, with excessive detail in black areas, increase the setting.
Again, good gamma improves contrast while maintaining good details for blacks and
whites.
automatically. To enable AGC, set it to ON. To disable it, set it to OFF.
correct color imbalances in the bright areas of the image. A good way to do this is to
use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window”
pattern. If the white areas contain traces of red or blue, decrease the Gain for that
color.
correct color imbalances in the dark areas of the image. A good way to do this is to use
a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern.
If the gray areas contain traces of red or blue, decrease the Offset for that color.
size.
remote control unit with the menu on-screen. Or, press
or
repeatedly to highlight
RESET in the menu, then press the ACTION ( ) button.
The CinemaWall memorizes position and size settings separately
for different input signal formats. Adjustments for component
signals are memorized for 525 (480) / 60i · 60p, 625 (575) / 50i ·
50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF,
1250 (1080) / 50i, 750 (720) / 60p · 50p each. RGB/PC/Digital
signals are memorized for each frequency.
Note
POS./SIZE
RESET
AUTO SETUP
NORMAL
H-POS
H-SIZE
0
0
V-POS
0
V-SIZE
0
DOT CLOCK
CLOCK PHASE
0
-16
RESET
ADJUST
SELECT
RETURN
CinemaWall Installation/Operation Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO SETUP (PC INPUT only): To automatically adjust the position, size, clock and
phase of incoming computer signals for optimum picture quality, press or repeatedly
to highlight AUTO SETUP in the menu, then press the ACTION ( ) button.
or
buttons to fine-tune the
displayed image position.
or
buttons to fine-tune the
display device aspect ratio.
Note
pixel sampling clock, indicated by the number of incoming pixels per line, so that all pixels
generated by a particular source are sampled.
Steady flickering or several soft vertical stripes or bands across the entire image indicates
poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent
across the screen, that aspect ratio is maintained and that pixel phase (see below) can be
optimized.
DOT CLOCK cannot be adjusted if the incoming signal pixel clock
frequency is 108 MHz or greater.
Note
sampling clock relative to the incoming signal. Adjust the phase when an RGB or
Tip
shimmer from a video or HDTV source persists, use the NOISE
high-frequency noise from the signal.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image. Adjust the
slidebar until the image stabilizes and each pixel is clearly defined. You may notice that
you can stabilize the image at more than one point. Use either setting in such cases.
the CinemaWall map a 1920x1080 input signal to 1080p HD
panel pixels, displaying 100% of the original content. By
skipping the scaling process, the CinemaWall can produce
high-definition images in their original, 1:1 pixel form.
1:1 PIXEL MODE = ON
scaled for over-scanning and 97% of the original is displayed.
Use this setting to minimize or eliminate image flicker.
1:1 PIXEL MODE = OFF
36
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. 1:1 PIXEL MODE is available only when the input signal is 1080i
Note
PIXEL MODE is enabled.
remote control unit with the menu on-screen. Or, press
or
repeatedly to highlight
RESET in the menu, then press the ACTION ( ) button.
SOUND
RESET
AUDIO MENU
BASS
MID
TREBLE
BALANCE
SURROUND
AUDIO OUT (PIP)
DYNAMIC
0
0
0
0
ON
MAIN
RESET
RETURN
ADJUST
SELECT
AUDIO MENU: The CinemaWall provides three audio memories for storing and recalling
“remembers” any adjustments you make when you switch to a different audio memory,
then switch back.
frequencies respectively in the audio signal.
menu. Use the
or
buttons to make one channel louder than the other.
SOUND menu and set it to ON.
AUDIO OUT (PIP): To swap the main and PIP audio programs when using the
CinemaWall Installation/Operation Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
access various other CinemaWall features.
➤
SET UP
1/2
SIGNAL
SCREENSAVER
COMPONENT/RGB-IN SELECT
COMPONENT
INPUT LABEL
DVD3
POWER SAVE
ON
STANDBY SAVE
OFF
ON
ON
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
ENGLISH (US)
RETURN
SELECT
ACCESS
SET UP
2/2
MULTI DISPLAY SETUP
MULTI PIP SETUP
PORTRAIT SETUP
SET UP TIMER
PRESENT TIME SETUP
RETURN
ACCESS
SELECT
signal and to adjust the following settings:
INPUT.
In most cases, the AUTO setting works well. However, if you know that your source
outputs an RGB with sync-on-green signal and the AUTO setting does not produce a
stable image, select ON G. Likewise, select VBS for a source that outputs an RGB with
composite sync signal.
CinemaWall attempts to reproduce a more natural interpretation of sources such as
movie pictures, which are recorded at 24 frames per second. If the image is not stable,
38
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SIGNAL menu and set it to 1024x768, 1280x768 or 1366x768.
images from interlaced SD sources. Set it to OFF, MIN, MID or MAX as needed. Or, if
you need more precise control over noise reduction, set it to ADVANCED, then press
to access the following controls:
• Video NR: Video NR is temporal and spatial noise reduction for all types of inputs.
The scene is analyzed for differences from frame to frame and reduces those
differences that are not determined to be motion.
• Block NR: Use this control to reduce or eliminate so-called “block artifacts” in
MPEG-compressed video signals (digital broadcasts or DVDs). Set it as needed to
minimize distortion within horizontal and vertical block boundaries.
• Mosquito NR: Use this control to reduce or eliminate so-called “mosquito noise” in
MPEG-compressed video signals. Set it as needed to minimize distortion around the
edges of moving objects, moving artifacts around edges and/or blotchy noise
patterns superimposed over the objects.
burn-in prevention settings on the CinemaWall.
To prevent image retention (burn) on your display, ALWAYS use a
screen saver and set it to the shortest possible time.
WARNING
following burn-in prevention methods:
• NEGATIVE IMAGE: An inverse image is displayed on the screen.
• SCROLLING BAR ONLY: The source image is replaced by a white bar scrolling
from left to right.
• OVERLAY SCROLLING BAR: The source image is dimmed and a white bar
scrolling from left to right is superimposed on it.
OVERLAY SCROLLING BAR cannot be selected when MULTI PIP
is active.
Note
• WHITE SCREEN: The source image is replaced by a white screen.
saver function becomes active.
• OFF: The screen saver is disabled.
• INTERVAL: The screen saver function becomes active after the selected SHOW
DURATION and remains active for the selected SAVER DURATION (see below). This
cycle repeats indefinitely.
• TIME OF DAY: The CinemaWall activates the screen saver function daily at the
selected START TIME and returns to normal operation at the selected FINISH TIME
(see below).
• ON: Select ON to activate the screen saver on demand. Then, press
or
repeatedly to highlight START in the menu and press the ACTION ( ) button.
CinemaWall Installation/Operation Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
set START TIME to the time of day that you want the screen saver to activate. When
presentation” interval (no screen saver).
Press or to change the SHOW DURATION interval in 15-minute increments, or to
change the START TIME in one-minute increments. Press and hold
the START TIME interval in 15-minute increments.
or
to change
set FINISH TIME to the time of day that you want the screen saver to deactivate. When
saver interval.
Press or to change the SAVER DURATION interval or FINISH TIME in one-minute
increments. Press and hold
or
to change the SAVER DURATION interval or
FINISH TIME in 15-minute increments.
RETURN
1. To deactivate the screen saver at any time, press RETURN (
on the remote control unit, or cycle power to the CinemaWall.
)
Note
2. You must set the day and time in order to use the INTERVAL or
TIME OF DAY screen saver mode; refer to Setting the Day and
an image in 4:3 mode for an extended
period, as this can cause image
side bars
4:3 mode
retention in the inactive areas of the
display. The same is true of P OUT P
and P AND P multi-screen modes.
image
retention
To help prevent this, select SIDE BAR
menu and set it to BRIGHT. (Other
choices are OFF, DARK and MID.)
Inactive areas
P OUT P
P AND P
protection against image retention.
unnoticeable to the eye) to prevent image retention. ON1 shifts the image every 30
seconds; ON2 shifts the image at a dot level pitch depending on screen detection.
SET UP menu to choose the color space of the for RGB and component source signals.
INPUT LABEL: You can give each CinemaWall input a descriptive name, to indicate the
type of component connected to it (for example, “DVD3” instead of “INPUT3”). To do this,
40
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
the overall image intensity by a small amount, thereby reducing power consumption.
minimize power consumption during standby mode.
set it to ON to activate the power management function for the PC INPUT. This feature,
when enabled, operates as follows:
• When no video or sync signals are detected on the PC INPUT for approximately 30
seconds, the power is turned off (standby) and the power indicator lights orange.
• When a signal is subsequently detected, power is restored and the power indicator
lights green.
to have the CinemaWall power itself off after 10 minutes when no signal is present on the
PC INPUT.
the PC INPUT and only under the following conditions:
Note
• MULTI PIP is off.
MULTI DISPLAY SETUP: You can create a video wall consisting of up to 25 (5x5)
CinemaWall displays and display an enlarged image across all of them. To do this, select
Then, configure each display in the video wall as follows:
SETUP menu, the set it to ON to activate multi-display mode.
In order to activate multi-display mode, you must first set the
Note
SETUP menu to specify the number of displays in each row of the video wall.
to specify the number of displays in each column of the video wall.
CinemaWall Installation/Operation Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
menu and set it to ON when displaying moving images on a video wall.
SEAM HIDES VIDEO joins the edges of adjacent displays in a video wall together in
such a way as to compensate for the gap between them. This causes moving objects
to appear to move “behind” the gap, for better continuity of motion across the wall:
ON hides joints between displays:
OFF shows joints between displays:
(suitable for moving image display)
(suitable for still image display)
CinemaWall’s position in the video wall. This determines which segment of the enlarged
image this panel will display.
Columns are numbered left to right from 1 to 5; rows are numbered top to bottom from
A to E:
2 × 1
2 × 3
4 × 2
4 × 4
5 × 5
A1
B1
C1
D1
E1
A2
B2
C2
D2
E2
A3
B3
C3
D3
E3
A4
B4
C4
D4
E4
A5
B5
C5
D5
E5
brightness setting to all CinemaWall displays in the video wall. Set it to OFF if you want
the ability to adjust the brightness of each display independently of the others.
OFF allows the brightness of each
ON equalizes the
display to be adjusted independently.
brightness of all displays.
42
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI PIP SETUP: The CinemaWall can display an image from two sources at the same
menu and press the ACTION ( ) button.
function. To switch to a different multi-PIP display mode, press the MULTI PIP remote
control button repeatedly.
• PIP: With PIP, three multi-PIP display modes are available:
[NORMAL]
[Picture and Picture]
Main picture Sub picture
[Picture out Picture]
[Picture in Picture]
Main picture
Sub picture Main picture Sub picture
B
A
A
A
A B
B
• ADVANCED PIP: Advanced PIP provides eight different multi-PIP display modes:
[NORMAL]
[1]
[2]
[3]
[4]
Sub screen Main screen
[8]
[7]
[6]
[5]
• BLEND PIP: Use Blend PIP to create a composite image from two sources. For
example, you can use a computer to display a caption over a movie or still image, in
either full-screen or picture-in-picture display mode:
[NORMAL]
[FULL]
[Picture in Picture]
B
C
D
Be aware that if you install the CinemaWall in a public place for
commercial purposes or a public showing, using Blend PIP to
create a composite image may violate copyright laws. It is
prohibited to show or alter copyrighted materials for commercial
purposes without the copyright owner’s permission.
Note
choose one of the multi-PIP display modes shown above. (This control has the same
effect as pressing the MULTI PIP remote control button repeatedly.)
CinemaWall Installation/Operation Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
you can make the overlay (sub) image transparent so that the main (background) image
shows through.
degree to which you want the main image to show through.
TRANSPARENCY = 0%
TRANSPARENCY = 50%
TRANSPARENCY = 90%
A B C D
Note
overlay (sub) image into transparent and non-transparent areas. The CinemaWall then
“inserts” only the non-transparent areas of the overlay image into the main
(background) image.
level threshold for distinguishing between the transparent and non-transparent areas of
the overlay image.
INSERT LEVEL = 1%
INSERT LEVEL = 5%
INSERT LEVEL = 10%
A B C D
A B C D
A B C
Note
44
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
displays in “portrait” mode and display an enlarged image across all of them.
1 2 3
)
button. Then, configure each display in the video wall as follows:
set it to ON to activate portrait mode.
In order to activate portrait mode, you must first set the MULTI-PIP
Note
CinemaWall’s position in the video wall. This determines which segment of the enlarged
image this panel will display. Select 1 for the left portion of the image, 2 for the center
portion or 3 for the right portion.
SET UP TIMER: To program the CinemaWall to turn on and/or off at specific times each
Note
to select POWER ON
TIME.
Press
hold
or
or
to select POWER OFF
TIME.
Press
hold
or
or
CinemaWall Installation/Operation Manual 45
Download from Www.Somanuals.com. All Manuals Search And Download.
perform other advanced, installation-related tasks.
➤
To access the OPTIONS menu:
1. Press SET UP.
2. Press
or
3. Press and hold the SURROUND (
) button until the page 1 of the OPTIONS menu
appears (approximately four seconds).
Opꢀons
1/3
Weekly Command Timer
Onscreen display
Iniꢀal INPUT
On
DVD3
Iniꢀal VOL level
Maximum VOL level
INPUT lock
Off
Off
0
0
INPUT1A
Off
Buꢁon lock
Remocon User level
User1
RETURN
ACCESS
SELECT
Opꢀons
2/3
Off-ꢀmer funcꢀon
Iniꢀal Power Mode
ID select
Enable
Normal
0
Remote ID
Off
Display size
Off
Studio W/B
On
Studio Gain
RETURN
CHANGE
SELECT
Opꢀons
3/3
Slot power
On
Off
Off
Power On Screen Delay
Clock Display
All Aspect
On
Rotate
Off
Serial Slot Select
Slot1
RETURN
CHANGE
SELECT
46
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Weekly Command Timer: You can program the CinemaWall to perform a series of
actions at specific times of the day and days of the week. To do this, you create
command sequences or “programs” consisting of a series of up to 64 individual
commands. You can create up to seven such programs and specify when they are
executed.
For example, you can store the following command sequence as a program:
1. 8:00 - Power On
2. 8:01 - Select INPUT1A
3. 8:01 - Set Volume to 30
4. 8:15 - Enable Multi-PIP
5. 8:20 - Activate Screen Saver
6. 8:30 - Deactivate Screen Saver
7. 9:00 - Power Off
ACTION ( ) button.
On to use this method to automate CinemaWall operation.
UP TIMER, nor can you use the INTERVAL or TIME OF DAY screen
saver modes.
Note
(Program1 ... Program7) that you want to use that day to control the CinemaWall. Or,
select “---” for manual operation.
CinemaWall Installation/Operation Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
a Program: Press
or
to select a
Weekly Command Timer
1/8
Program
1
PON
IMS:SL1A
OMS:SCR1
---
---
---
---
---
program to edit.
01
02
03
04
05
06
07
08
6:30
6:30
6:35
--:--
--:--
--:--
--:--
--:--
b To define the first command in the
program, press to select “01” and
press the ACTION ( ) button.
RETURN
CHANGE
SELECT
c Press
to select “Time.”
Weekly Command Timer
d Press or to change the time of day
at which you want the CinemaWall to
execute the command, in one-minute
Program
01
6:30
IMS:SL1A
1
Command No
Time
Command
increments. Or, press and hold
to change the time in 15-minute
increments.
or
RETURN
CHANGE
SELECT
e Press
to select “Command.”
f Press
or
RETURN
g Press RETURN ( ).
i
Edit menu. Or, to move between “pages” of the command list (there are eight
commands per page), press
or
.
Repeat this procedure as needed to create additional programs.
enable the display of the following on-screen indications:
• Current input and aspect ratio on power-up
• Input switch
• No signal display
• Mute and the remaining time on the off-timer when RECALL (
) remote control
button is pressed twice.
switch to a specific input every time it is turned on. Set it to Off to have the CinemaWall
display whichever input was active when it was turned off.
In order to select an initial input, you must set INPUT lock to Off
Note
48
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
sound volume level upon power-up.
Press or to set it to On, then use the VOL- or VOL+ (
) button to set the desired
initial volume level. When you do, the volume changes so you can preview your selection
before exiting the menu.
level (see below).
Note
the sound volume from being set higher than a preferred threshold.
Press
or
to set it to On, then use the VOL- or VOL+ (
) button to set the
maximum volume level. When you do, the volume changes so you can preview your
selection before exiting the menu.
Note
2. The volume display can go up to 63 regardless of the Maximum
VOL level setting. However, increasing the volume setting
to be displayed and prevent the others from being selected. Set it to Off to allow any input
to be selected.
OSD menu access via the remote control. Choose one of the following:
• Off: No restriction. All remote control buttons are functional.
• User1: Only the POWER, INPUT, RECALL, SURROUND, MUTE, VOL- and VOL+
remote control buttons are functional.
• User2: Only the POWER button is functional.
• User3: Disables the remote control altogether.
Use this feature with caution. Once you select User3, the only
way to change it to something other than User3 is via the serial
Caution
currently active.
Note
CinemaWall Installation/Operation Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
the CinemaWall recovers from a power interruption (resulting either from a power failure or
from being unplugged, then plugged back in):
• Normal: The CinemaWall returns to whatever power-on state it was in before the
power interruption.
• Standby: The CinemaWall comes on in standby mode. The power indicator lights red
or orange.
• On: The CinemaWall returns to “power on” mode. The power indicator lights green.
When using multiple displays – such as in a video wall – Runco
recommends setting this to “Standby” in order to minimize power
load.
Note
CinemaWall.
size of the displayed image by approximately five percent (5%).
1. This setting is not available when MULTI-PIP, Digital Zoom or
MULTI-DISPLAY is active.
Note
aspect ratios can be selected.
temperature to a level appropriate for television broadcast applications.
Note
contrast for a better view when a part of the image is too light to see.
transmitted to the terminal boards installed in SLOT1, SLOT2 and SLOT3. Choose one of
the following:
• Off: Power is not transmitted to the slot power.
• Auto: Power is transmitted to the slot power only when main power is on.
• On: Power is transmitted to the slot power when main power is on or in the standby
state.
In some cases, power is transmitted to the slot when the
CinemaWall is on or in the standby state regardless of the Slot
power setting.
Note
50
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power On Screen Delay: In a large video wall installation, it may be advisable to turn the
displays on one at a time rather than all at once, so as not to overload the power source.
To make this easier, you can set the CinemaWall to wait up to 30 seconds after you press
OPTIONS menu. Select from 1 to 30 seconds of delay. For example, in a 2x2 video wall
you might set a 4-second delay on display “A1,” an 8-second delay on display “A2,” a
12-second delay on display “A3” and no delay (Off) on display “A4.”
During the delay period, the power indicator flashes green.
Note
Clock Display: To have the CinemaWall display the time of day (in addition to the current
Until you set the day and time (refer to Setting the Day and Time
Note
All Aspect: This option controls which aspect ratio selections are available to the viewer.
the viewer does not need that level of aspect ratio control, set it to Off for the sake of
simplicity.
Rotate: If the CinemaWall is suspended from a ceiling, you may want to mount it upside
down and run the cables upward (toward the ceiling) to make them less visible. If you do,
OSD menus 180 degrees.
Serial Slot Select: This menu option does not currently apply to the CinemaWall.
The CinemaWall allows you to zoom in on a
portion of the displayed image. To use this
feature:
4.9
Using Digital Zoom
1. Press the MOVE/ZOOM ( ) button.
2. An on-screen guide appears. Press the
ACTION ( ) button to select a zoom level
EXIT
(x1, x2, x3 or x4).
1
3. Press
,
,
or to select an area of the
image to enlarge. The on-screen guide
shows you the selected area as you do this.
RETURN
4. To return to normal viewing mode, press RETURN ( ) or MOVE/ZOOM ( ).
CinemaWall Installation/Operation Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
52
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Maintenance and Troubleshooting
Regular cleaning will extend the life and performance of the CinemaWall. Before cleaning,
be sure to unplug the power cord from the power outlet.
5.1
Cleaning
Do not under any circumstances use solvents such as benzene or thinner to clean the
CinemaWall. Doing so may cause deterioration or peeling of paint from the display or
remote control unit.
Cleaning the Display
Panel Body and Remote
Control
Wipe the display and remote control gently with a soft cloth. In the case of excessive dirt
buildup, dampen a soft cloth with a diluted neutral cleaning detergent and after wringing
the cloth thoroughly, wipe the component and then dry it with a dry soft cloth.
After dusting, wipe the screen gently using a soft cloth (cotton, flannel etc.). Do not use
tissue or a rough cloth. The screen surface is easily scratched; do not rub it or hit it with a
hard object.
Cleaning the Screen
Cleaning the Vents
If you clean the surface of the screen with a wet cloth, water droplets on the surface may
enter into the product and cause a malfunction.
As a general rule, use a vacuum cleaner about once a month to clean the vents on the
rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting
when doing this). If not removed, accumulated dust can cause the internal temperature to
increase, resulting in possible breakdown or fire.
CinemaWall Installation/Operation Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the CinemaWall. If the suggested solutions fail to resolve the problem or if
you encounter an issue not described here, please contact your Runco dealer or Runco
Technical Support.
5.2
Troubleshooting Tips
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
The display does not turn on
after initial installation.
• The CinemaWall is not
plugged in or the AC outlet
is not active.
• Ensure that the
CinemaWall is plugged in
and that the AC outlet is
active.
• The remote control
batteries have run out.
• Replace the batteries.
The display is on and menus
appear, but there is no
picture.
• Incorrect source selection.
• Source component is not
turned on.
• Select the correct source.
• Turn on the source
component.
• Source component is
connected incorrectly or
not at all.
• Check connections from
source component to
CinemaWall.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Picture level (contrast) is
set too high.
• Lower the contrast setting
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high.
• Lower the brightness
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
CinemaWall.
• Ensure that the source
outputs are connected to
the correct CinemaWall
input.
RGB-HD images appear
“noisy.”
• Clock and Phase settings
need adjustment.
• Adjust Clock and Phase
settings (refer to SIGNAL
Computer images do not dis-
play correctly.
• The resolution and
frequency of the video
card in the computer are
not compatible with the
CinemaWall.
• Select a compatible
resolution and vertical
frequency (refer to
page 66).
The image is too large, too
small or positioned incor-
rectly.
• Image size and/or position
needs adjusting.
• Adjust the image size
and/or position (refer to
54
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Serial Communications
To interface the CinemaWall with a home theater automation/control system or a PC
running terminal emulation software, connect it to your control system or PC as shown in
6.1
RS-232 Connection
and Port Configuration
Configure the RS-232 controller or PC serial port as follows:
• 9600 baud
• No parity
• Eight (8) data bits
• One (1) stop bit
• No flow control
Serial commands to the CinemaWall take the following form:
• You can send commands in either hexadecimal or ASCII format.
• ASCII commands are case-sensitive and must be in UPPERCASE.
6.2
Serial Command
Syntax
• Commands begin with the “Start of Text” (STX) character (02h or <Ctrl> Bin ASCII),
followed by the command data, the colon character (3Ah or :in ASCII), command
or <Ctrl> Cin ASCII). Not all commands require parameters to be sent with them;
examples of such commands are PON(power on), POF(power off) and IMS(toggle
input selection).
• You do not need to send a carriage return after the command.
• When sending multiple commands, be sure to wait for a response to the first command
to come from the CinemaWall before sending the next command.
• When you send a valid command, the CinemaWall executes it and echoes the
command (without the parameter) back to the controller.
• If you send an invalid command, the CinemaWall sends ER401back to the controller.
To select the PC input, send the following sequence:
Examples
STX
02
Command (3 bytes)
49 4D 53
Parameter (3 bytes)
50 43 31
ETX
03
3A
:
Hex
<Ctrl> B
I M S
P C 1
<Ctrl> C
ASCII
To set the Picture Level (contrast) to its highest possible level (+30), send the following
sequence:
STX
02
Command (3 bytes)
56 50 43
Parameter (6 bytes)
50 49 43 30 33 30
P I C 0 3 0
ETX
03
3A
:
Hex
<Ctrl> B
V P C
<Ctrl> C
ASCII
CinemaWall Installation/Operation Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1 lists the CinemaWall serial command set.
Table 6-1. Serial Commands
ASCII
AAC:BAL030
AAC:BAL-30
AAC:BAS015
AAC:BAS-15
AAC:MENCLR
AAC:MENDYN
AAC:MENSTD
AAC:MID015
AAC:MID-15
AAC:SURMON
AAC:SUROFF
AAC:TRE015
AAC:TRE-15
AMT:0
Hex
Description
Balance = 30 (right channel only)
Balance = -30 (left channel only)
Bass = 15 (max)
41 41 43 3A 42 41 4C 30 33 30
41 41 43 3A 42 41 4C 2D 33 30
41 41 43 3A 42 41 53 30 31 35
41 41 43 3A 42 41 53 2D 31 35
41 41 43 3A 4D 45 4E 43 4C 52
41 41 43 3A 4D 45 4E 44 59 4E
41 41 43 3A 4D 45 4E 53 54 44
41 41 43 3A 4D 49 44 30 31 35
41 41 43 3A 4D 49 44 2D 31 35
41 41 43 3A 53 55 52 4D 4F 4E
41 41 43 3A 53 55 52 4F 46 46
41 41 43 3A 54 52 45 30 31 35
41 41 43 3A 54 52 45 2D 31 35
41 4D 54 3A 30
Bass = -15 (min)
Audio Menu = CLEAR
Audio Menu = DYNAMIC
Audio Menu = STANDARD
Midrange = 15 (max)
Midrange = -15 (min)
Surround = ON
Surround = OFF
Treble = 15 (max)
Treble = -15 (min)
Audio Mute = OFF
AMT:1
41 4D 54 3A 31
Audio Mute = ON
ASO:M
41 53 4F 3A 4D
Audio out when in PIP mode =
Main Picture
ASO:S
41 53 4F 3A 53
Audio out when in PIP mode =
Sub Picture
AUD
41 55 44
Audio Volume Down
Audio Volume Up
AUU
41 55 55
AVL:00
AVL:10
AVL:20
AVL:30
AVL:40
AVL:50
AVL:60
DAM:FULL
DAM:JUST
DAM:NORM
41 56 4C 3A 30 30
41 56 4C 3A 31 30
41 56 4C 3A 32 30
41 56 4C 3A 33 30
41 56 4C 3A 34 30
41 56 4C 3A 35 30
41 56 4C 3A 36 30
44 41 4D 3A 46 55 4C 4C
44 41 4D 3A 4A 55 53 54
44 41 4D 3A 4E 4F 52 4D
Audio Volume = 00
Audio Volume = 10
Audio Volume = 20
Audio Volume = 30
Audio Volume = 40
Audio Volume = 50
Audio Volume = 60
Aspect Ratio = 16:9
Aspect Ratio = VIRTUALWIDE
Aspect Ratio = 4:3
56
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
ASCII
Hex
Description
Aspect Ratio = LETTERBOX
Aspect Ratio = CINEMA
Phase = 16 (max)
DAM:ZOOM
DAM:CINE
44 41 4D 3A 5A 4F 4F 4D
44 41 4D 3A 43 49 4E 45
DGE:CLK0016
DGE:CLK-016
DGE:HPO0124
DGE:HPO-124
DGE:HSZ0062
DGE:HSZ-062
DGE:VPO0124
DGE:VPO-124
DGE:VSZ0062
DGE:VSZ-062
DWA:OFF
44 47 45 3A 43 4C 4B 30 30 31 36
44 47 45 3A 43 4C 4B 2D 30 31 36
44 47 45 3A 48 50 4F 30 31 32 34
44 47 45 3A 48 50 4F 2D 31 32 34
44 47 45 3A 48 53 5A 30 30 36 32
44 47 45 3A 48 53 5A 2D 30 36 32
44 47 45 3A 56 50 4F 30 31 32 34
44 47 45 3A 56 50 4F 2D 31 32 34
44 47 45 3A 56 53 5A 30 30 36 32
44 47 45 3A 56 53 5A 2D 30 36 32
44 57 41 3A 4F 46 46
Phase = -16 (min)
Horiz. Position = 124 (max)
Horiz. Position = -124 (min)
Width = 62 (max)
Width = -62 (min)
Vert. Position = 124 (max)
Vert. Position = -124 (min)
Height = 62 (max)
Height = -62 (min)
Dual Picture mode = OFF
Advanced PIP mode = 1
Advanced PIP mode = 2
Advanced PIP mode = 3
Advanced PIP mode = 4
Advanced PIP mode = 5
Advanced PIP mode = 6
DWA:OVL1
44 57 41 3A 4F 56 4C 31
DWA:OVL2
44 57 41 3A 4F 56 4C 32
DWA:OVL3
44 57 41 3A 4F 56 4C 33
DWA:OVL4
44 57 41 3A 4F 56 4C 34
DWA:OVL5
44 57 41 3A 4F 56 4C 35
DWA:OVL6
44 57 41 3A 4F 56 4C 36
DWA:OVLOF
44 57 41 3A 4F 56 4C 4F 46
Advanced PIP mode = OFF (nor-
mal two-screen display mode)
DWA:OVLON
DWA:PIN0
DWA:PIN1
DWA:PIN2
DWA:PIN3
DWA:PIP
44 57 41 3A 4F 56 4C 4F 4E
44 57 41 3A 50 49 4E 30
44 57 41 3A 50 49 4E 31
44 57 41 3A 50 49 4E 32
44 57 41 3A 50 49 4E 33
44 57 41 3A 50 49 50
Advanced PIP mode = ON
PIP window position = lower right
PIP window position = lower left
PIP window position = upper left
PIP window position = upper right
Dual Picture mode = Picture in
Picture
DWA:POP
DWA:SWP
DWA:TWN
44 57 41 3A 50 4F 50
44 57 41 3A 53 57 50
44 57 41 3A 54 57 4E
Dual Picture mode = Picture out
Picture
Swap main picture and sub pic-
ture when PIP mode
Dual Picture mode = Picture and
Picture
CinemaWall Installation/Operation Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
ASCII
IMS:PC1
Hex
Description
49 4D 53 3A 50 43 31
Input select = PC1 (Main Picture
when PIP mode)
IMS:SL1A
IMS:SL1B
IMS:SL2A
IMS:SL2B
IMS:SL3
49 4D 53 3A 53 4C 31 41
49 4D 53 3A 53 4C 31 42
49 4D 53 3A 53 4C 32 41
49 4D 53 3A 53 4C 32 42
49 4D 53 3A 53 4C 33
Input select = SLOT1A (Main Pic-
ture when PIP mode)
Input select = SLOT1B (Main Pic-
ture when PIP mode)
Input select = SLOT2A (Main Pic-
ture when PIP mode)
Input select = SLOT2B (Main Pic-
ture when PIP mode)
Input select = SLOT3 (Main Pic-
ture when PIP mode)
ISS:PC1
49 53 53 3A 50 43 31
Sub Picture Input Select = PC1
ISS:SL1A
49 53 53 3A 53 4C 31 41
Sub Picture Input Select =
SLOT1A
ISS:SL1B
ISS:SL2A
ISS:SL2B
49 53 53 3A 53 4C 31 42
49 53 53 3A 53 4C 32 41
49 53 53 3A 53 4C 32 42
Sub Picture Input Select =
SLOT1B
Sub Picture Input Select =
SLOT2A
Sub Picture Input Select =
SLOT2B
ISS:SL3
49 53 53 3A 53 4C 33
4F 53 50 3A 4F 53 44 30
4F 53 50 3A 4F 53 44 31
Sub Picture Input Select = SLOT3
OSP:OSD0
OSP:OSD1
OSD OFF
OSD ON
OSP:RCM0
OSP:RCM1
4F 53 50 3A 52 43 4D 30
4F 53 50 3A 52 43 4D 31
Remote Control User Level = Off
Remote Control User Level =
User1
OSP:RCM2
OSP:RCM3
4F 53 50 3A 52 43 4D 32
4F 53 50 3A 52 43 4D 33
Remote Control User Level =
User2
Remote Control User Level =
User3
OSP:SCR0
OSP:SCR1
4F 53 50 3A 53 43 52 30
4F 53 50 3A 53 43 52 31
Screen Saver SCROLLING BAR
ONLY = OFF
Screen Saver SCROLLING BAR
ONLY = ON
POF
50 4F 46
Power OFF
Power ON
PON
50 4F 4E
SSC:0000
53 53 43 3A 30 30 30 30
Screen Saver Duration = 0:00
(Interval Mode) or Finish Time =
0:00 (Time of Day Mode)
58
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
ASCII
Hex
Description
SSC:2359
53 53 43 3A 32 33 35 39
Screen Saver Duration = 23:59
(Interval Mode) or Finish Time =
11:59PM (Time of Day Mode)
SSC:FNC0
53 53 43 3A 46 4E 43 30
Screen Saver function =
SCROLLING BAR ONLY
SSC:FNC1
53 53 43 3A 46 4E 43 31
Screen Saver function =
NEGATIVE IMAGE
SSC:INT0000
SSC:INT2345
53 53 43 3A 49 4E 54 30 30 30 30
53 53 43 3A 49 4E 54 32 33 34 35
Screen Saver Show Duration =
0:00 (Interval Mode)
Screen Saver Show Duration =
23:45 (Interval Mode)
SSC:MOD0
SSC:MOD1
SSC:MOD2
SSC:MOD3
SSC:SPC0
SSC:SPC1
SSC:SPC2
SSC:SPC3
SSC:TIM0000
53 53 43 3A 4D 4F 44 30
53 53 43 3A 4D 4F 44 31
53 53 43 3A 4D 4F 44 32
53 53 43 3A 4D 4F 44 33
53 53 43 3A 53 50 43 30
53 53 43 3A 53 50 43 31
53 53 43 3A 53 50 43 32
53 53 43 3A 53 50 43 33
53 53 43 3A 54 49 4D 30 30 30 30
Screen Saver Mode = OFF
Screen Saver Mode = Interval
Screen Saver Mode = Time of Day
Screen Saver Mode = ON
Side Bar Adjust = OFF
Side Bar Adjust = DARK
Side Bar Adjust = MID
Side Bar Adjust = BRIGHT
Screen Saver Start Time = 0:00
(Time of Day Mode)
SSC:TIM2359
53 53 43 3A 54 49 4D 32 33 35 39
Screen Saver Start Time =
11:59PM (Time of Day Mode)
SSG:SNCGRN
SSG:SNCHAV
SSG:SNCVID
53 53 47 3A 53 4E 43 47 52 4E
53 53 47 3A 53 4E 43 48 41 56
53 53 47 3A 53 4E 43 56 49 44
Sync Mode (PC IN) = ON G
Sync Mode (PC IN) = AUTO
Sync Mode (PC IN) = VBS (Com-
posite)
SSU:CMPRGB
SSU:CMPYBR
53 53 55 3A 43 4D 50 52 47 42
53 53 55 3A 43 4D 50 59 42 52
Component/RGB In Select = RGB
Component/RGB In Select =
COMPONENT
TIM:DAYMON
TIM:DAYSUN
54 49 4D 3A 44 41 59 4D 4F 4E
Present Day = Monday
Present Day = Sunday
54 49 4D 3A 44 41 59 53 55 4E
TIM:NOW00000
TIM:NOW02359
TIM:POF00000
TIM:POF10000
54 49 4D 3A 4E 4F 57 30 30 30 30 30
54 49 4D 3A 4E 4F 57 30 32 33 35 39
54 49 4D 3A 50 4F 46 30 30 30 30 30
54 49 4D 3A 50 4F 46 31 30 30 30 30
Present Time of Day = 0:00
Present Time of Day = 11:59PM
Power Off Time = None
Power Off Time = 0:00
CinemaWall Installation/Operation Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
ASCII
TIM:POF12359
TIM:PON00000
TIM:PON10000
TIM:PON12359
VDO
Hex
Description
Power Off Time = 11:59PM
Power On Time = None
Power On Time = 0:00
Power On Time = 11:59PM
OSD clear
54 49 4D 3A 50 4F 46 31 32 33 35 39
54 49 4D 3A 50 4F 4E 30 30 30 30 30
54 49 4D 3A 50 4F 4E 31 30 30 30 30
54 49 4D 3A 50 4F 4E 31 32 33 35 39
56 44 4F
VMT
56 4D 54
Picture Mute (toggle)
VMT:0
56 4D 54 3A 30
Picture Mute = OFF
VMT:1
56 4D 54 3A 31
Picture Mute = ON
VPC:BLK030
VPC:BLK-30
VPC:MENSTD
VPC:MENDYN
VPC:MENCNM
VPC:MENMON
VPC:PAJ0
56 50 43 3A 42 4C 4B 30 33 30
56 50 43 3A 42 4C 4B 2D 33 30
56 50 43 3A 4D 45 4E 53 54 44
56 50 43 3A 4D 45 4E 44 59 4E
56 50 43 3A 4D 45 4E 43 4E 4D
56 50 43 3A 4D 45 4E 4D 4F 4E
56 50 43 3A 50 41 4A 30
56 50 43 3A 50 41 4A 31
56 50 43 3A 50 49 43 2D 33 30
Brightness = 30 (max)
Brightness = -30 (min)
Picture Menu = Standard
Picture Menu = ISF Day
Picture Menu = ISF Night
Picture Menu = Monitor
Color management = OFF
Color management = ON
VPC:PAJ1
VPC:PIC-30
Picture Level (Contrast) = -30
(min)
VPC:PIC000
VPC:PIC030
56 50 43 3A 50 49 43 30 30 30
56 50 43 3A 50 49 43 30 33 30
Picture Level (Contrast) = 0
Picture Level (Contrast) = 30
(max)
VPC:SHP015
VPC:SHP-15
VPC:TMPCOL
VPC:TMPMID
VPC:TMPWRM
VWB:BCT030
VWB:BCT-30
VWB:BDR030
VWB:BDR-30
VWB:BEX000
VWB:BEX008
VWB:GCT030
56 50 43 3A 53 48 50 30 31 35
56 50 43 3A 53 48 50 2D 31 35
56 50 43 3A 54 4D 50 43 4F 4C
56 50 43 3A 54 4D 50 4D 49 44
56 50 43 3A 54 4D 50 57 52 4D
56 57 42 3A 42 43 54 30 33 30
56 57 42 3A 42 43 54 2D 33 30
56 57 42 3A 42 44 52 30 33 30
56 57 42 3A 42 44 52 2D 33 30
56 57 42 3A 42 45 58 30 30 30
56 57 42 3A 42 45 58 30 30 38
56 57 42 3A 47 43 54 30 33 30
Sharpness = 15 (max)
Sharpness = -15 (min)
Color Temp = COOL
Color Temp = NORMAL
Color Temp = WARM
Blue Offset = 30 (max)
Blue Offset = -30 (min)
Blue Gain = 30 (max)
Blue Gain = -30 (min)
Black Extension = 0 (min)
Black Extension = 8 (max)
Green Offset = 30 (max)
60
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
ASCII
Hex
Description
Green Offset = -30 (min)
Green Gain = 30 (max)
Green Gain = -30 (min)
Gamma = 2.0
VWB:GCT-30
VWB:GDR030
VWB:GDR-30
VWB:GMM20
VWB:GMM22
VWB:GMM25
VWB:GMMSC
VWB:ILV032
VWB:ILV-32
VWB:RCT030
VWB:RCT-30
VWB:RDR030
VWB:RDR-30
VWB:TEC0
56 57 42 3A 47 43 54 2D 33 30
56 57 42 3A 47 44 52 30 33 30
56 57 42 3A 47 44 52 2D 33 30
56 57 42 3A 47 4D 4D 32 30
56 57 42 3A 47 4D 4D 32 32
56 57 42 3A 47 4D 4D 32 35
56 57 42 3A 47 4D 4D 53 43
56 57 42 3A 49 4C 56 30 33 32
56 57 42 3A 49 4C 56 2D 33 32
56 57 42 3A 52 43 54 30 33 30
56 57 42 3A 52 43 54 2D 33 30
56 57 42 3A 52 44 52 30 33 30
56 57 42 3A 52 44 52 2D 33 30
56 57 42 3A 54 45 43 30
Gamma = 2.2
Gamma = 2.5
Gamma = S-Curve
Input Level = 32 (max)
Input Level = -32 (min)
Red Offset = 30 (max)
Red Offset = -30 (min)
Red Gain = 30 (max)
Red Gain = -30 (min)
Advanced Settings = OFF
Advanced Settings = ON
VWB:TEC1
56 57 42 3A 54 45 43 31
CinemaWall Installation/Operation Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
62
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Table 7-1 lists the CinemaWall specifications.
7.1
CinemaWall
Specifications
Table 7-1. CinemaWall Specifications
Native Resolution:
Screen Size:
1920 x 1080
XP-50, XP-OPAL50:
43.50 in. W x 24.50 in. H (1106.0 x 622.0 mm)
50 in. (1270.0 mm) diagonal
XP-65, XP-OPAL65:
56.50 in. W x 31.80 in. H (1434.0 x 807.0 mm)
65 in. (1646.0 mm) diagonal
Screen Aspect Ratio:
Available Aspect Ratios:
DTV Compatibility:
16:9
Refer to Table 4-1
480p, 720p, 1080i, 1080p
30,000:1 maximum
Contrast Ratio:
Data/Graphics Compatibility:
VGA, SVGA, XGA, SXGA, UXGA (compressed)
Horiz. scan frequency = 15 to 110 kHz
Vert. scan frequency = 48 to 120 Hz
Video Inputs:
(4) Digital Video (HDMI 1.2A with HDCP)
(1) Component/RGB (BNCx3) with Stereo Audio (RCAx2)
(1) PC (15-pin D-Sub)
(1) RS-232 (9-pin, D-sub male)
Audio System
Internal amplifier
Output Power = 10W RMS x 2 at 8Ω
Power Requirements:
Power Consumption:
100 to 240 VAC, 50/60Hz
XP-50, XP-OPAL50: 605 W (0.9 W in standby), maximum
XP-65, XP-OPAL65: 755 W (1.0 W in standby), maximum
Operating Environment:
40ºF to 95ºF (5ºC to 35ºC);
20% to 80% humidity (non-condensing)
Ambient air pressure = 720 hPa, minimum
Altitude = up to 9,100 feet (2,774 meters)
Dimensions:
XP-50, XP-OPAL50: See Figure 7-1
XP-65, XP-OPAL65: See Figure 7-2
Weight
XP-50, XP-OPAL50: 93.0 lbs. (42.18 kg)
(panel only, without stand):
XP-65, XP-OPAL65: 163.1 lbs. (73.98 kg)
Regulatory Approvals:
Complies with FCC Part 15 Class B, ICES-003, UL6500
Ver.2
Specifications are subject to change without notice.
CinemaWall Installation/Operation Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
0
0
1.98
.55
2.35
3.69
7.81
12.31
50.14
54.64
61.90
62.45
62.45
0
.55
10.06
16.95
38.10
52.39
61.90
62.45
Figure 7-2. CinemaWall Model XP-65 and XP-OPAL65 Dimensions (with Optional
Table Stand)
CinemaWall Installation/Operation Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2 lists the signal types supported by each input on the CinemaWall.
7.3
Supported Timings
Table 7-2. Supported Signal Timings by Input
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
HDMI 1A
RefreshRate
(Hz)
Pixel Frequency
(MHz)
Format
Resolution
HDMI 1B
HDMI 2A
HDMI 2B
COMPONENT
PC IN
/RGB
60.00
66.67
72.00
75.00
85.00
56.00
60.00
72.00
75.00
85.00
74.54
60.00
60.00
70.00
75.00
85.00
75.00
75.06
60.00
85.00
60.00
75.00
85.00
60.00
60.00
65.00
31.469
35.000
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.720
31.726
48.363
56.476
60.023
68.677
67.500
68.680
60.000
85.938
63.981
79.976
91.146
48.360
75.000
81.250
25.175
30.240
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
34.010
65.000
75.000
78.750
94.500
108.000
100.330
108.000
148.500
108.000
135.000
157.500
80.000
161.200
162.000
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
640x480
640x480
800x600
800x600
832x624
852x480
832x624
852x480
1024x768
1024x768
1152x864
1152x870
1152x864
1152x870
1280x960
1280x960
1280x1024
1280x1024
1366x768
1366x768
1600x1200
1600x1200
(displays at
1125/60p)
1920x1080
1920x1080
60.00
67.470
148.550
–
–
66
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2. Supported Signal Timings by Input (continued)
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
HDMI 1A
HDMI 1B
HDMI 2A
HDMI 2B
RefreshRate
(Hz)
Pixel Frequency
Format
Resolution
COMPONENT
/RGB
(MHz)
PC IN
480/60i
480/60p
576/50i
720x487
720x483
59.94
59.94
50.00
50.00
50.00
60.00
50.00
15.734
31.469
13.500
27.000
√
√
√
√
√
√
√
√
√
√
√
√
–
√
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
720x576
15.625
14.750
576/50p
720/50p
720/60p
1080/50i
1080/60i
1080/24p
1080/24sF
1080/50p
1080/60p
720x576
31.250
29.000
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
37.500
75.250
45.000
74.250
28.125/31.250
74.250/72.000
74.175/74.250
74.175/74.250
74.175/74.250
148.500
59.94/60.00 33.716/33.750
23.98/24.00 26.978/27.000
47.92
50.00
27.000
56.250
59.94/60.00 67.433/67.500 148.350/148.500
CinemaWall Installation/Operation Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
68
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Default Settings
Table A-1 lists the CinemaWall factory-default image settings. All of these settings are in
Table A-1. Runco Factory Default Settings for CinemaWall
Models XP-50 and XP-OPAL50
Model XP-65 and XP-OPAL65
Menu Setting
MONITOR ISF Night STANDARD ISF DAY
ISF Night STANDARD ISF DAY
MONITOR
PICTURE
30
30
30
–
30
30
30
–
BRIGHTNESS
COLOR
-5
-2
-2
0
-6
-4
-4
0
-2
-2
-2
0
0
-2
-2
-2
0
0
TINT
0
3
0
3
0
3
0
5
0
5
0
5
SHARPNESS
COLOR TEMP
0
0
NORMAL
OFF
NORMAL
OFF
NORMAL
OFF
WARM
OFF
NORMAL
OFF
NORMAL
OFF
NORMAL
OFF
WARM
OFF
COLOR
MANAGEMENT
ADVANCED SETTINGS
BLACK EXTENSION
INPUT LEVEL
GAMMA
ON
0
ON
ON
OFF
–
ON
0
ON
ON
OFF
–
0
0
0
0
0
0
0
0
0
–
0
–
2.2
OFF
3
S-Curve
OFF
3
S-Curve
OFF
3
–
2.2
OFF
-2
S-Curve
OFF
-2
S-Curve
OFF
-2
–
AGC
–
–
R GAIN
–
–
G GAIN
0
0
0
–
0
0
0
–
B GAIN
-18
-11
-7
-18
-11
-7
-18
-11
-7
–
-14
-1
-14
-1
-14
-1
–
R OFFSET
G OFFSET
B OFFSET
–
–
–
-2
-2
-2
–
0
0
0
–
0
0
0
–
1:1 Pixel Mode
On
On
On
Off
On
On
On
Off
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
A-2
CinemaWall Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
020-0970-01 Rev. A
September 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
|