Samsung Flat Panel Television HPN5039 User Guide

Owner’s Instructions  
HPN 5 0 3 9 / HPN 6 3 3 9  
SERVICE DIVISION  
400 Valley Road, Suite 201  
Mount Arlington, NJ 07856  
TEL : 1-800-SAMSUNG (1-800-726-7864)  
BN68-00476A-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC In fo rm a tio n  
• Protect the power cord. Power supply cords should be routed so that they wont be walked on or pinched  
by objects placed on or against them. Pay particular attention to cords at plugs, convenience recepta-  
cles, and the point where they exit from the unit.  
Use r In stru ctio n s  
Wa rn in g  
The Federal Communications Commission Radio  
Frequency Interference Statement includes the fol-  
lowing warning:  
User must use shielded signal interface cables to  
maintain FCC compliance for the product.  
Provided with this monitor is a detachable power  
• Unplug the PDP from the wall outlet and disconnect the antenna or cable system during a lightning storm  
or when left unattended and unused for long periods of time. This will prevent damage to the unit due to  
lightning and power-line surges.  
NOTE: This equipment has been tested and found supply cord with IEC320 style terminations.  
to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a resi-  
dential installation. This equipment generates,  
uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with  
It may be suitable for connection to any UL Listed  
personal computer with similar configuration.  
Before making the connection, make sure the volt-  
age rating of the computer convenience outlet is  
the same as the monitor and that the ampere rat-  
ing of the computer convenience outlet is equal to  
or exceeds the monitor voltage rating.  
• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead  
power lines or other electric light or power circuits or where it can fall into such power lines or circuits.  
When installing an outside antenna system, be extremely careful to keep from touching the power lines  
or circuits. Contact with such lines can be fatal.  
the instructions, may cause harmful interference to For 120 Volt applications, use only UL Listed  
radio communications. However, there is no guar- detachable power cord with NEMA configuration  
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.  
antee that interference will not occur in a particu-  
lar installation .  
5-15P type (parallel blades) plug cap. For 240  
Volt applications use only UL Listed Detachable  
power supply cord with NEMA configuration  
6015P type (tandem blades) plug cap.  
• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points  
or damage parts. Never spill liquid of any kind on the PDP.  
If this equipment does cause harmful interference  
to radio or television receptions, which can be  
determined by turning the equipment off and on,  
the user is encouraged to try to correct the inter-  
ference by one or more of the following mea-  
sures:  
Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the  
antenna or cable system is grounded so as to provide some protection against voltage surges and built-  
up static charges. Section 810 of the National Electrical Code, ANSI/ NFPA No.70-1984, provides infor-  
mation about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an  
antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to  
grounding electrodes, and requirements for the grounding electrode.  
IC Co m p lia n ce N o tice  
This Class B digital apparatus meets all require-  
ments of the Canadian Interference-Causing  
Equipment Regulations of ICES-003.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment  
and receiver.  
• Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
Cet appareil Numérique de classe B respecte  
toutes les exigences du Règlemont NMB-03 sur les  
équipements produisant des interférences au  
Canada.  
• Do not attempt to service the PDP yourself. Refer all servicing to qualified service personnel. Unplug the  
unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:  
- when the power-supply cord or plug is damaged  
- if liquid has been spilled on the unit or if objects have fallen into the unit  
- if the PDP has been exposed to rain or water  
- if the PDP does not operate normally by following the operating instructions  
- if the PDP has been dropped or the cabinet has been damaged  
- when the PDP exhibits a distinct change in performance  
• Consult the dealer or an experienced radio/ TV  
technician for help.  
N o tice d e Co n fo rm ité IC  
Cet appareil numérique de classe B respecte  
toutes les exigences du Règlement ICES-003 sur  
les équipements produisant des interférences au  
Canada.  
Use r In fo rm a tio n  
Changes or modifications not expressly approved  
by the party responsible for compliance could  
VCCI  
void the users authority to operate the equipment. This is a Class B product based on the standard  
If you make adjustments yourself, adjust only those controls that are covered by the operating instruc-  
tions. Adjusting other controls may result in damage and will often require extensive work by a qualified  
technician to restore the PDP to normal.  
If necessary, consult your dealer or an experi-  
enced radio/ television technician for additional  
of the Voluntary Control Council for Interference  
by Information Technology Equipment (VCCI). If  
suggestions. You may find the booklet called How this is used near a radio or television receiver in a  
to Identify and Resolve Radio/ TV Interference  
Problems helpful. This booklet was prepared by  
the Federal Communications Commission. It is  
available from the U.S. Government Printing  
Office, Washington, DC 20402, Stock Number  
004-000-00345-4 .  
domestic environment, it may cause radio interfer-  
ence. Install and use the equipment according to  
the instruction manual.  
When replacement parts are required, be sure the service technician uses replacement parts specified by  
the manufacturer or those that have the same characteristics as the original part. Unauthorized substitu-  
tions may result in additional damage to the unit.  
• Upon completion of any service or repairs to this PDP, ask the service technician to perform safety checks  
to determine that the PDP is in a safe operating condition.  
The party responsible for product compliance:  
SAMSUNG ELECTRONICS CO., LTD  
America QA Lab of Samsung  
The PDP can properly operate in a temperature range of 32~104°F(0~40°C) and 80% humidity.  
Do not use in a hot and humid place.  
3351 Michelson Drive,  
Suite #290, Irvine, CA92612 USA  
Before moving the PDP equipped with speakers, separate the speakers from the PDP. If you move the PDP  
with the speakers attached, it may result in damage or injury.  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Im p o rta n t W a rra n ty In fo rm a tio n  
Re g a rd in g Te le visio n Fo rm a t Vie w in g  
Ta b le o f Co n te n ts  
Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily  
designed to view wide screen format full-motion video.The images displayed on them should primarily be  
in the wide screen 16:9 ratio format,or expanded to fill the screen if your model offers this feature and con-  
stantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on non-  
expanded standard format television video and programming, should be limited to no more than 5% of the  
total television viewing per week.  
General Information  
Channel Control  
Fine Tuning Channels ..................................62  
Your New Plasma Display Panel ....................10  
Remote Control Buttons ................................12  
Wall Installation Instructions ..........................14  
LNA (Low Noise Amplifier) ..........................63  
Connecting a PC and Operation  
Additionally,viewing other stationary images and text such as stock market reports, video game  
displays,station logos,web sites or computer graphics and patterns,should be limited as described above  
for all televisions. Disp la y in g sta tio n a r y im a g e s th a t e x ce e d th e a b o ve g u id e lin e s ca n  
ca u se u n e ve n a g in g o f PDP Disp la y s th a t le a ve su b tle ,b u t p e rm a n e n t b u rn e d -in  
g h o st im a g e s in th e PDP p ictu re .To a vo id th is,va r y th e p ro g ra m m in g a n d im a g e s,  
a n d p rim a rily d isp la y fu ll scre e n m o vin g im a g e s,n o t sta tio n a r y p a tte rn s o r d a rk b a rs.  
On PDP models that offer picture sizing features,use these controls to view different formats as a full screen  
picture.  
Connections  
Connecting to a PC ....................................66  
Adjusting the PC Screen ..............................70  
Changing the Position of the Image................71  
Changing the Size of the Image ..................72  
Information ................................................73  
Picture Quality Adjustment ..........................74  
Connecting VHF and UHF Antennas ..............20  
Connecting Cable TV ..................................20  
Connecting Speakers ..................................22  
Connecting a VCR ......................................24  
Connecting a Camcorder ............................25  
Connecting a DVD Player ............................26  
Connecting a DTV Receiver ..........................27  
Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a  
result of format selection and use,as well as burned-in images, are not covered by your Samsung limited  
warranty.  
Time Setting  
Setting the Clock ........................................78  
Setting the Sleep Timer ................................79  
Setting the Timers ........................................80  
Setting the Preferred Channel and Volume Level ....82  
Operation  
Turning the PDP On and Off ........................30  
Memorizing the Channels ............................32  
Setting Up Your Remote Control ....................37  
Function Description  
Use r In stru ctio n s  
Picture Control  
Selecting a Menu Language ........................84  
Viewing Closed Captions ............................85  
Digital Noise Reduction ..............................86  
Setting Auto Power Off ................................87  
Using the V-Chip..........................................88  
Selecting the Film Mode ..............................94  
Customizing the Picture ..............................40  
Using Automatic Picture Settings ..................41  
Selecting the Color Tone ..............................42  
DNIe (Digital Natural Image engine) ............43  
Viewing the Picture-in-Picture ........................44  
Changing the Screen Size ..........................50  
Freezing the Picture ...................................51  
Screen Image retention  
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma  
display panel for more than several minutes as it can cause screen image retention. This image retention is  
also known as screen burn”. To avoid such image retention, refer to page 40 of this manual to reduce the  
degree of brightness and contrast of this screen when displaying a still image.  
Cell Defect  
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9  
Appendix  
percent active cells, there may be some cells that do not produce light or remain lit.  
Troubleshooting ..........................................96  
Care and Maintenance ................................97  
Specifications..............................................98  
Sound Control  
Altitude  
Customizing the Sound ................................54  
Using Automatic Sound Settings ...................55  
Choosing a Multi-Channel Sound (MTS)Soundtrack ......56  
Using the Auto Volume ................................57  
Using Dolby Virtual......................................58  
Using a Subwoofer ......................................59  
The PDP will not operate normally at altitudes above 6500 ft.  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Ge n e ra l In fo rm a tio n  
Your New Plasma Display Panel ....................................................10  
Remote Control Buttons ................................................................12  
Wall Installation Instructions ..........................................................14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Yo u r N e w Pla sm a Disp la y Pa n e l  
Front Panel  
Rear Panel  
HPN5039  
ŒService jack  
ØComponent Video/ Audio Input jacks  
For service only.  
b
r
(Y/ P / P / Audio L/ Audio R)  
Connect to the audio and component output  
jacks of a DVD player or Set-Top Box.  
´DVI Input jacks  
Receives the digital video/ audio signals  
from a set top box or PC.  
External Speaker Out jacks  
Connect external speakers.  
ˇPC(RGB) Input jacks(15pin)  
Connect to the video/ audio output jacks  
on your PC.  
HPN6339  
Antenna jack  
Connect to antenna.  
¨S-Video Input jacks  
Connect S-Video/ audio signals from external  
sources such VCRs or DVD players.  
Sub-woofer speaker output jack  
Connect to the Sub-woofer speaker jack.  
˝Power Input jack  
ˆVideo Input jacks  
Connect the supplied power cord.  
Connect video/ audio signals from external  
sources such VCRs or DVD players.  
Checking Accessories  
Once you have unpacked your TV, check to make sure that you have all the parts shown here.  
If any piece is missing or broken, call your dealer.  
ŒSOURCE button  
ˆPOWER button  
Press to display all of the available video  
sources (ie., Video, S-Video, Component1,  
Component2, PC ).  
Press to turn the PDP on and off.  
ØPower Indicator  
Power Off : LED Red  
´MENU button  
Displays the main on-screen menu.  
Power On (Timer On) : LED Green  
Power On (Timer Off) : LED Off  
Remote Control/ AAA Batteries  
Antenna Cable  
Speaker Cables  
ˇVOL(+,-) button  
Remote Control Signal Receiver  
Aim the remote control towards  
this spot on the PDP.  
Press to increase or decrease the volume. Also  
used to select or adjust items on the on-screen  
menu.  
Speakers (optional)  
¨CH(M,M) button  
Press CHMMor CHM to change Channels.  
Also used to move up or down in the On-screen  
menu.  
Power Cord  
Ferrite Cores; 3EA  
(HPN5039)  
Owners Instructions  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Re m o te Co n tro l Bu tto n s  
¸SURROUND button  
Press the hear the Dolby surround effect.  
˛ MTS button  
Press to choose stereo, mono or Separate Audio Pro-  
gram (SAP broadcast).  
Remote Control  
AUTO PROG. button  
The TV automatically cycles through all of the avail-  
able channels and stores them in memory.  
ŒPOWER button  
Turns the PDP on and off.  
ADD/ DEL button  
´ASPECT button  
Press to add or delete channels in the TV’s memory.  
Press to change the screen size.  
DNIe button  
ˇNumber buttons  
Activates DNIe (Digital Natural Image engine).  
¨+100 button  
CAPTION button  
Press to select channels over 100. For example, to select  
channel 121, press “+100”, then press “2” and “1.”  
Controls the caption decoder.  
SET button  
ˆMUTE button  
Used during set up of this Samsung remote control,  
so that it will work compatibly with other devices  
(VCR, cable box, DVD)  
Press to mute the PDP sound.  
ØVOL (Volume) buttons  
Use it to adjust volume.  
÷PIP control buttons  
SLEEP button  
SWAP : Exchanges the video signal that is currently  
displayed on the main screen with the  
signal in the PIP window.  
Press to select a preset time interval for automatic shutoff.  
MENU button  
Displays the main on-screen menu.  
SIZE  
: Press to make the PIP window Large, Small  
or Double.  
ENTER button  
Confirms a selection.  
CHL,L : Displays the available channels in  
sequence. (These buttons change channels  
in the PIP window only).  
˝PIP button  
Activates picture in picture.  
ÔSTILL button  
®VCR, DVD control buttons  
Press to pause the current screen.  
Controls VCR tape or DVD disc functions: Stop,  
Rewind, Play/ Pause, Fast Forward.  
LED Display  
When you press a button, ‘ appears along with  
selected mode (TV, CATV, DVD or STB) and remaining  
batteries on LED.  
RESET button  
If your remote control is not functioning properly, take  
out the batteries and press the reset button for about  
2~3 seconds. Re-insert the batteries and try using the  
remote control again.  
ÒP.MODE button  
Adjust the PDP picture by selecting one of the preset  
factory settings (or select your personal, customized  
picture settings.)  
ÚMODE button  
Selects a target device to be controlled by the Samsung  
remote control (ie., VCR, Cable, DVD players or STB).  
If you change modes, the new mode is momentarily  
displayed on LED.  
Installing the Batteries in Your Remote Control  
Slide the back cover  
Install two AAA size batter-  
Slide the cover back into  
1 to open the battery  
2 ies. Make sure to match the  
3 place.  
ÆPRE-CH button  
compartment of the  
remote control.  
“+” and “-ends of the bat-  
teries with the diagram  
inside the compartment.  
Tunes to the previous channel.  
ıTV/ VIDEO button  
Press to display all of the available video sources  
(ie., Video, S-Video, Component1, Component2, PC, DVI).  
˜CH (Channel) buttons  
Use it to switch channels.  
¯INFO button  
Press to display information on the PDP screen.  
˘EXIT button  
Remote Control Operation Range.  
Press to exit the menu.  
You can use your remote control within a distance of 23 feet and an angle of 30 degrees  
from the left and right sides of the PDPs remote control receiver.  
¿Up/ Down Left/ Right buttons  
Control the cursor in the menu.  
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wa ll In sta lla tio n In stru ctio n s  
Installation Notes  
Fixing the PDP panel to the wall attachment panel bracket  
Remove the screws on the rear of the PDP panel.  
Do not install the PDP in any location other than a vertical wall.  
1
1
2
To protect the performance of the PDP and prevent problems, avoid the following  
places.  
HPN5039  
HPN6339  
• Do not install next to smoke and fire detectors.  
• Do not install in an area subjected to vibration.  
• Do not install in an area subjected to high voltage.  
• Do not install near or around any heating apparatus.  
Use only recommended parts and components.  
Removing four screws  
Removing six screws  
3
Connect Insulation holders to screws. (see the illustration below)  
2
3
Parts  
(Wall attachment panel is sold separately. Check with your dealer)  
Wall attachment panel  
HPN5039  
HPN6339  
Tighten the screws connected to the Insulation holders on the rear of the PDP panel.  
HPN5039  
HPN6339  
Connecting six screws  
Connecting four screws  
Insulation holders  
(HPN5039; 4 EA  
HPN6339; 6 EA)  
Screws  
(HPN5039; 4 EA  
HPN6339; 6 EA)  
14  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Adjust Mounting Angle  
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on  
the PDP (Œ) to secure it to the wall mount bracket. (´) Tighten the screws as shown  
(ˇ) so that the PDP cannot be separated from wall mount bracket.  
N o tice : Please secure the mounting bracket on the wall surface after setting its angle at 0°  
4
Factory default  
HPN5039  
HPN5039  
HPN6339  
PDP panel  
Wall  
Wall attachment  
panel bracket  
The wall mount bracket is delivered separately.Please tighten the captive screw in the direction of  
the arrow after assembling the bracket.  
HPN6339  
PDP panel  
Changeing the angle  
Secure the PDP to the wall mount  
bracket.(Please refer to the following  
instructions.)  
1
Wall  
Set the angle by pulling the upper end of  
the PDP attached to bracket in the direction  
of the arrow.  
2
Wall attachment  
panel bracket  
The angle can be adjusted from 0° to 20°  
by ±2°.  
3
1. Contact an authorized technician when installing the wall attachment panel.  
2. After hanging the PDP panel on the wall attachment panel, make sure that  
the Insulation holders are completely hung.  
3. Be careful so that fingers are not caught.  
4. Make sure the wall attachment panel brackets are tightened.  
Otherwise, the PDP panel may fall down and you might be hurt.  
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Connections  
Connecting VHF and UHF Antennas ..............................................20  
Connecting Cable TV....................................................................20  
Connecting Speakers.................................................................. ..22  
Connecting a VCR........................................................................24  
Connecting a Camcorder ..............................................................25  
Connecting a DVD Player..............................................................26  
Connecting a DTV Receiver ..........................................................27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g VHF a n d UHF An te n n a s  
Antennas with 75-ohm Round Leads  
If your antenna looks like this:  
Cable with a Cable Box that Descrambles Some (But Not All) Channels  
To complete this connection you will need a two-way splitter, an RF (A/ B) switch, and four coaxial  
cables (which you can buy from your Samsung dealer or any electronics store).  
it has 75-ohm round leads.  
Find and disconnect the cable that is con-  
nected to the ANTENNA IN terminal of  
your cable box.  
This terminal might be labeled "ANT IN",  
"VHF IN", or simply, "IN". Connect this  
cable to a two-way splitter.  
Plug the antenna lead into the VHF/ UHF terminal  
on the PDP.  
Use the Antenna Cable, an accessory included  
in the product package.  
1
1
Connect a coaxial cable between an OUT-  
PUT terminal of the splitter and the IN termi-  
nal of the cable box.  
2
Co n n e ctin g Ca b le TV  
You can connect different cable systems to your PDP, including cable without a cable box,  
and cable with a cable box that descrambles some or all channels.  
Connect a coaxial cable between the  
ANTENNA OUT terminal of the cable box  
and the B-IN terminal of the A/ B switch.  
3
Cable without a Cable Box  
Plug the incoming cable into the VHF/ UHF terminal on  
the PDP.  
1
Use the Antenna Cable, an accessory included  
in the product package.  
Connect a coaxial cable between the  
ANTENNA OUT terminal of the cable box  
and the B-IN terminal of the A/ B switch.  
4
Cable with a Cable Box that Descrambles All Channels.  
Connect the last coaxial cable between the  
OUT terminal of the RF (A/ B) switch and  
the VHF/ UHF terminal on the PDP.  
5
Find the cable connected to the ANTENNA OUT  
terminal on your cable box. This terminal might be  
labeled "ANT OUT", "VHF OUT", or simply "OUT".  
1
Connect the cable to the VHF/ UHF terminal on the  
PDP.  
Use the Antenna Cable, an accessory included  
in the product package.  
After you've made this connection, set the A/ B switch to the "A" position for normal viewing.  
Set the A/ B switch to the "B" position to view scrambled channels. (When you set the A/ B switch  
to "B", you will need to tune your Set-Top Box to the cable box's output channel, which is usually  
channel 3 or 4.)  
2
20  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g Sp e a k e rs  
External speakers are sold seperately. Check with your dealer.  
HPN5039  
Connecting PDP and Speakers  
SSppeeaakkeerr AAuuddiioo CCaabbllee  
HPN5039  
Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.  
1
After removing the four screws on the rear of PDP.  
2
As shown in figure, insert the loop on a speaker into the groove on the PDP.  
3
Clamp the speaker and the PDP together and fasten the screws.  
4
Powered Subwoofer  
(Option)  
External speakers MUST have a power handling  
Guide  
pole  
capability of 10 watts minimum (impedance 8 ohm).  
Guide  
pole  
Please use the speaker-built in amplified audio.  
HPN6339  
SSppeeaakkeerr AAuuddiioo CCaabbllee  
HPN6339  
Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.  
1
After removing the three screws on the PDP, clamp the speaker and the PDP together and  
fasten the screws.  
2
Guide  
pole  
Powered Subwoofer  
(Option)  
External speakers MUST have a power handling  
capability of 10 watts minimum (impedance 8 ohm).  
Guide  
pole  
Please use the speaker-built in amplified audio.  
How to Connect  
Connect the speaker audio cable to the external speaker output jack on the PDP matching the  
“+” and “-ends of the cable with the diagram on the PDP.  
22  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g a VCR  
Co n n e ctin g a Ca m co rd e r  
Connecting a VCR to the Video or S-Video/Audio jack  
Viewing camcorder tapes  
PDP  
VCR  
Camcorder  
PDP  
Power Plug  
Audio Cable  
S-Video Cable  
Power Plug  
Ferrite Cores(HPN5039)  
Video Cable  
Video Cable  
Audio Cable  
Ferrite Cores(HPN5039)  
How to Connect  
Connect the Video/ Audio cables between the AUDIO(L/ R)/ VIDEO jacks on the PDP and  
AUDIO/ VIDEO OUT jacks on the VCR. (Note: For better video, you can use an S-Video cable.)  
How to Connect  
Videotape Playback:  
1. Turn on your PDP, and press the TV/ VIDEO button on the remote control.  
Connect a Video/ Audio cable between the AUDIO(L/ R)/ VIDEO jacks on the PDP and the  
VIDEO/ AUDIO OUTPUT jacks on the camcorder.  
2. Press the UP or DOWN button to select “Video” or “S-Video”, then press the ENTER button.  
3. Turn on your VCR, insert a videotape and press the play button.  
Viewing Tapes  
1. Turn on your PDP, and press the TV/ VIDEO button on the remote control.  
2. Press the UP or DOWN button to select the “Video”, then press the ENTER button.  
3. Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder  
owner's instructions.)  
Ferrite Cores (HPN5039)  
The ferrite cores are used to attenuate undesired signals. When connecting the audio cable  
4. Set the IN/ OUT switch on your camcorder to OUT.  
(PC, DVI, S-Video, Video), attach one of these ferrite cores to the cable near the connector.  
5. Insert the tape into the camcorder and press the Play button.  
When you connect the audio cable (PC, DVI, S-Video, Video,  
Component1, Component2) to the connectors, bind the ferrite core  
around the cable to secure it.  
24  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g a DVD Pla y e r (4 8 0 i, 4 8 0 p )  
Co n n e ctin g a DTV Re ce ive r  
This PDP displays the optimum picture in 720p mode.  
(4 8 0 p , 7 2 0 p , 1 0 8 0 i)  
This PDP displays the optimum picture in 720p mode.  
Playing DVD  
Watching DTV  
PDP  
DVD Player  
PDP  
DTV Receiver  
Power  
Plug  
Power Plug  
Video Cable  
Video Cable  
or  
Audio Cable  
Audio Cable  
DVI Cable  
Ferrite Cores(HPN5039)  
Use the DVI-D connection cable. (sold separately)  
How to Connect  
How to Connect  
Connect a Video Cable between the Y, Pb, Pr (COMPONENT1, 2) input jacks on the PDP  
Connect the cable or antenna to the antenna input jack on the DTV.  
1
2
B
R
1
and Y/ P / P output jacks on the DVD players.  
Connect a Video cable between the Y, Pb, Pr (COMPONENT 1, 2) or DVI jack on the PDP  
Connect a Audio Cable between the AUDIO L/ R(COMPONENT1, 2) input jacks on the PDP  
and the AUDIO OUT jacks on the DVD player.  
2
B
R
and the Y, P , P (VIDEO OUTPUT JACKS) on the DTV receiver.  
Connect an Audio cable between the COMPONENT 1, 2 (L/ R AUDIO) or DVI jacks on the  
PDP and the AUDIO OUTPUT jacks on the DTV.  
3
To Play DVD:  
1. Turn on your PDP, and press the TV/ VIDEO button on the remote control.  
To Watch DTV:  
2. Press the UP or DOWN button to select “COMPONENT1” or “COMPONENT2,  
then press the ENTER button.  
1. Turn on your PDP, and press the TV/ VIDEO button on the remote control.  
3. Turn on your DVD player, insert a DVD disc and press the Play button.  
• For an explanation of Component video, see your DVD owners instructions.  
2. Press the UP or DOWN button to select “COMPONENT1, “COMPONENT2” or  
“DVI”, then press the ENTER button.  
3. Turn on your DTV receiver.  
• For an explanation of Component video, see your DTV receiver owners instructions.  
26  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
O p e ra tio n  
Turning the PDP On and Off ..........................................................30  
Memorizing the Channels..............................................................32  
Setting Up Your Remote Control ....................................................37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the PDP On a nd Off  
Displaying Status Information  
Turning the PDP On and Off  
Press the Power button on the remote control.  
The PDP will be turned on and you will be ready to use it’s  
features.  
Press the INFO button on the remote control. The PDP will  
display the Picture mode, Sound mode, MTS, Signal and  
Caption.  
Press the INFO button on the remote control again.  
The PDP will display the Clock.  
Ant 6  
Picture  
Sound  
MTS  
Signal  
Caption  
:
:
:
:
:
Custom  
Custom  
Mono  
Mono  
Off  
You can also use the POWER(  
PDP.  
) button on the front of the  
Notes:  
If your PDP isn’t turned on when the power button is  
pressed: Press the MODE button to check if the TV mode  
has been chosen ( ).  
07 : 30 am  
Viewing the Menus and Displays  
Your PDP has a simple, easy-to-use menu system that appears on the PDP screen. This system makes it con-  
venient and fast to use features on the PDP. Your PDP also lets you display the status of many of your PDPs  
features.  
Viewing the Menus  
With the power on, press the MENU button on the  
Picture  
remote control. The main menu appears on the screen.  
The Picture menu is selected.  
1
Mode  
Custom  
Adjust  
Color Tone  
DNIe  
Normal  
On  
Move  
Enter  
Menu  
Press the UP/ DOWN buttons to move items in the menu.  
Press the LEFT/ RIGHT buttons to display, change, or use  
the selected items.  
2
Press the ENTER (  
) button to enter items in the menu.  
On screen menus disappear from the screen  
automatically after about thirty seconds, or you can  
press the EXIT button on your remote control to exit  
the menu.  
30  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Me m o rizin g th e Ch a n n e ls  
Your PDP can memorize and store all of the available channels for both “off-air” (antenna)  
and cable channels. After the available channels are memorized, use the CH  
and CH  
buttons to scan through the channels. This eliminates the need to change channels by entering  
the channel digits. There are three steps for memorizing channels: selecting a broadcast  
source, memorizing the channels (automatic) and adding and deleting channels (manual).  
Storing Channels in Memory (Automatic Method)  
First, select the correct signal source (Ant, STD, HRC,  
IRC). See steps on previous page.  
Press the MENU button. Press the UP or DOWN button  
to select “Channel”, then press the ENTER button.  
Channel  
Ant  
Selecting the Video Signal-source  
1
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
Before your television can begin memorizing the available channels, you must specify the type of  
signal source that is connected to the PDP (i.e., an antenna or a cable system).  
0
Off  
Ch. Scan  
Quick way to access the Automatic Channel Setting : Just press the  
AUTO PROG.” button on the remote control.  
Press the MENU button. Press the UP or DOWN  
button to select “Channel”, then press the ENTER  
button.  
Channel  
Move  
Select  
Menu  
1
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
Ant  
0
Off  
Press the UP or DOWN button to select “Auto Pro-  
gram”, then press the ENTER button.  
Ch. Scan  
Channel  
Ant  
2
3
Ant / CATV  
Auto Program  
Fine Tune  
LNA  
Move  
Select  
Menu  
0
Off  
Ch. Scan  
Press the LEFT or RIGHT button to select “Ant”,  
“STD”, “HRC” or “IRC”.  
Channel  
STD  
Move  
Enter  
Menu  
2
3
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
If you are connected to an antenna, leave "Ant"  
displayed. If you connected cable, press the  
LEFT or RIGHT button to the display the type of  
cable system: "STD", "HRC", or "IRC".  
(If you are not sure which type of cable system you  
have, contact your cable company).  
0
Off  
Ch. Scan  
The PDP will begin memorizing all of the available  
channels.  
After all the available channels are stored, the  
Auto program menu reappears. Press the RIGHT  
button to stop.  
Move  
Select  
Menu  
Ant 50  
Auto Program  
: Stop  
Press the MENU button to exit.  
Note  
The PDP automatically cycles through all of the available channels and stores them in memory.  
This takes about one to two minutes.  
Note  
STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company  
to identify the type of cable system that exists in your particular area.  
At this point the signal source has been selected. Proceed to “Storing Channels in Memory”  
(next page).  
32  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adding and Erasing Channels (Manual Method)  
To View Memorized Channel (PIP Mode)  
Use the number buttons to directly select the channel that  
will be added or erased.  
Press the MENU button. Press the UP or DOWN  
button to select “Channel”, then press the ENTER  
button.  
Channel  
Ant  
Ant 4  
1
1
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
0
Ex) Channel “4”  
Off  
Ch. Scan  
Move  
Select  
Menu  
Press the ADD/ DEL button:  
Repeatedly pressing this button will alternate between  
“Added” and “Erased.”  
Press the UP or DOWN button to select “Ch Scan”,  
then press the ENTER button.  
Only the memorized channels are chosen.  
Press the RIGHT button to stop.  
Channel  
Ant  
2
2
Ant / CATV  
Auto Program  
Fine Tune  
LNA  
0
Off  
Ch. Scan  
Move  
Enter  
Menu  
Ch. Scan  
Ant  
: Stop  
7
Ant 4  
Added  
Note  
You can view any channel (including an erased channel) by using the number buttons on the remote  
control.  
34  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se ttin g Up Yo u r Re m o te Co n tro l  
This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up  
properly, your remote control can operate in four different modes :TV, VCR, Cable or DVD.  
Pressing the corresponding button on the remote control allows you to switch between these modes,  
and control whichever piece of equipment you choose.  
Changing Channels  
Using the Channel Buttons  
Note :  
The remote control may not be compatible with all DVD Players, VCRs, Cable boxes.  
The remote control can operate only on STB made by Samsung.  
Press the CH  
or CH  
buttons to change channels.  
or CH buttons, the PDP changes channels  
When you press the CH  
in sequence. You will see all the channels that the PDP has memorized.  
(The PDP must have memorized at least three channels.)  
Setting Up the Remote to Operate Your VCR, Cable box or DVD player  
You will not see channels that were either erased or not memorized.  
Turn off your VCR. (or Cable box, DVD player)  
1
Directly Accessing Channels  
Press the number buttons to go directly to a channel. For example, to select  
channel 27, press “2” then “7. The TV will change channels when you  
press the second number.  
Press the MODE button. Mode is changed whenever  
MODE button is pressed(New mode is displayed on  
LED screen).  
When you use the number buttons, you can directly select channels that were  
either erased or not memorized. To change to single-digit channels (0~9) faster,  
press “0” before the single digit. (For channel “4” press “0”, then “4”.  
2
Press the SET button on your TV's remote control.  
Using the Pre-CH button to select the previous channel  
3
Press the PRE-CH button. The TV will switch to the last channel viewed.  
To quickly switch between two channels that are far apart, tune to one  
channel, then use the number button to select the second channel. Then,  
use the PRE-CH button to quickly alternate between them.  
Using the number buttons on your remote control,  
enter three digits of the VCR (or Cable box, DVD  
4
player) code listed on page 38 of this manual for  
your brand of VCR (or CATV, DVD). Make sure you  
enter three digits of the code, even if the first digit  
is a "0".  
Adjusting the Volume  
Using the Volume Buttons  
(If more than one code is listed, try the first one.)  
Press the VOL + or VOL – buttons to increase or decrease the volume.  
Press the Power button on the remote control.  
Your VCR (or CATV, DVD) should turn on if your  
5
Using Mute  
remote is set up correctly. If your VCR (or CATV,  
DVD) does not turn on after setup, repeat steps  
2, 3, and 4, but try one of the other codes listed for  
your brand of VCR (or CATV, DVD).  
If no other codes are listed, try each code, 000  
through 089 (or Cable box: 000 through 077,  
DVD player: 000 through 008).  
Using the MUTE Buttons  
At any time, you can temporarily cut off the sound using the MUTE button.  
Press the MUTE button and the sound cuts off.  
The word “Mute” will appear in the lower-left  
corner of the screen.  
1
Notes  
When your remote control is in “VCRmode, the VCR control buttons (Stop, REW, Play/ Pause, FF)  
still operate your VCR.  
To turn mute off, press the MUTE button again, or  
simply press the VOL + or VOL – button.  
When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (Stop, REW,  
Play/ Pause, FF) still operate your VCR.  
2
Mute  
36  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Codes  
VCR Codes  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Cable Box Codes  
Pictu re Co n tro l  
Customizing the Picture ................................................................40  
Using Automatic Picture Settings ....................................................41  
Selecting the Color Tone................................................................42  
DNIe (Digital Natural Image engine) ............................................43  
Viewing the Picture-in-Picture ..........................................................44  
Changing the Screen Size ............................................................50  
Freezing the Picture ......................................................................51  
DVD Codes  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cu sto m izin g th e Pictu re  
Usin g Au to m a tic Pictu re Se ttin g s  
You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color,  
and Tint settings of your PDP.  
Your PDP has automatic picture settings that allow you to adjust the video display easily.  
Press the MENU button, then press the ENTER  
button.  
Press the MENU button, then press the ENTER  
button.  
Picture  
Custom  
Picture  
Custom  
Mode  
1
2
3
4
5
1
2
3
Mode  
Adjust  
Adjust  
Color Tone  
DNIe  
Custom  
On  
Color Tone  
DNIe  
Custom  
On  
Quick way to access the picture setting: Just press the “P.MODE”  
button under the cover of the remote control.  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Adjust”,  
then press the ENTER button.  
You will also see the items “Contrast”, “Brightness”,  
“Sharpness”, “Color” and “Tint”.  
Press the LEFT or RIGHT button to select “Custom”,  
“Dynamic”, “Standard” or “Movie” picture setting.  
You can select “High”, “Middle”, “Low” or  
“Custom” in PC/ DVI mode.  
Picture  
Dynamic  
Picture  
Custom  
Mode  
Mode  
Adjust  
Adjust  
Color Tone  
DNIe  
Custom  
On  
Color Tone  
DNIe  
Normal  
On  
Move  
Select  
Menu  
Move  
Enter  
Menu  
Press the UP or DOWN button to select the item you  
wish to change.  
Press the MENU button to exit.  
Adjust  
Contrast  
Brightness  
Sharpness  
Color  
80  
50  
50  
50  
Tint  
R 50  
G 50  
Move  
Adjust  
Menu  
Press the LEFT or RIGHT button to change the value  
of the item.  
Contrast  
82  
Press the MENU button to exit.  
Note  
In the PC/ DVI mode, you cant adjust the Sharpness, Color and Tint.  
The Tint cannnot be adjusted in Component(480p, 720p, 1080i) mode.  
40  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se le ctin g th e Co lo r To n e  
DN Ie (Dig ita l N a tu ra l Im a g e e n g in e )  
Samsung’ s New Technology brings you more detailed images with contrast and  
white enhancement and 3D noise reduction.  
Press the MENU button, then press the ENTER  
button.  
Press the MENU button, then press the ENTER  
button.  
Picture  
Custom  
Picture  
Custom  
1
2
1
2
Mode  
Mode  
Adjust  
Adjust  
Color Tone  
DNIe  
Custom  
On  
Color Tone  
DNIe  
Custom  
On  
Quick way to select DNIe : Simply press the “DNIe” button under  
the cover of the remote control.  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Color  
Tone”, then press the LEFT or RIGHT button to select  
Normal”, “Warm1, “Warm2, “Cool2” or  
“Cool1.  
Press the UP or DOWN button to select “DNIe”,  
then press the LEFT or RIGHT button to select  
On”, “Off” or “Demo”.  
Picture  
Custom  
Picture  
Custom  
Mode  
Mode  
Adjust  
Adjust  
Color Tone  
DNIe  
Normal  
On  
Color Tone  
DNIe  
Normal  
On  
You can select “Custom”, “Color1, “Color2” or  
“Color3” in PC mode.  
You can select “Color1”, “Color2” or “Color3” in  
DVI mode.  
On : Switches on the DNIe mode.  
• Demo : The screen before applying DNIe  
appears on the right and the screen after  
applying DNIe appears on the left.  
Off : Switches off the DNIe mode.  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
DNIe Demo  
3
DNIe On  
DNIe Off  
.
Press the MENU button to exit.  
3
Note  
The DNIe function doesn’t operate in the DVI modes.  
42  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Vie w in g th e Pictu re -in -Pictu re  
Selecting the PIP Screen  
Selecting an External Signal  
You can use PIP to view a signal from an external source, such as a VCR.  
Press the MENU button. Press the UP or DOWN  
button to select “PIP”, then press the ENTER button.  
PIP  
Off  
1
Select  
Press the MENU button. Press the UP or DOWN  
PIP  
button to select “PIP”, then press the ENTER button.  
1
Select  
On  
TV  
Quick way to access the PIP mode: Just press the “PIP” button on  
the remote control.  
Source  
Swap  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Select  
Menu  
Ant  
5
Move  
Select  
Menu  
Press the LEFT or RIGHT button to select “On”.  
The PIP image will appear in the corner of the  
screen.  
• Pressing the LEFT or RIGHT button will alternate  
between “Onand “Off.”  
PIP  
Press the UP or DOWN button to select “Source”.  
PIP  
Select  
On  
TV  
2
3
Source  
Swap  
2
Select  
On  
TV  
Source  
Swap  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Ant  
5
Move  
Select  
Menu  
Ant  
5
Move  
Select  
Menu  
Press the MENU button to exit.  
Press the LEFT or RIGHT button to cycle through  
all of the available signal sources:  
TV, “Video”, “S-Video”, “Component 1”,  
“Component 2”, “PC” and “DVI.  
PIP  
3
Select  
Source  
Swap  
Size  
On  
Video  
Large  
Locate  
O : PIP and Swap Operate  
X : PIP doesnt Operate  
The signal from these inputs will not appear if you  
have not connected any equipment to the PDP's  
respective input jacks.  
PIP Settings  
Move  
Select  
Menu  
Main screen  
PIP screen  
TV  
Video  
S-Video  
Component 1 Component 2  
PC  
DVI  
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
X
X
X
X
O
O
O
X
X
X
X
O
O
O
X
X
X
X
O
O
O
X
X
X
X
TV  
Press the MENU button to exit.  
Video  
S-Video  
4
Component 1  
Component 2  
PC  
Note  
The PIP function operates in Wide screen.  
DVI  
Using Multi-Screen in the Normal, Zoom1 or Zoom2 screen will change the size of the main screen  
to Wide screen.  
44  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Swapping the Contents of the PIP Image and Main Image  
Changing the Size of the PIP Window  
Press the MENU button. Press the UP or DOWN  
button to select “PIP”, then press the ENTER button.  
Press the MENU button. Press the UP or DOWN  
button to select “PIP”, then press the ENTER button.  
PIP  
PIP  
1
1
Select  
On  
TV  
Select  
On  
TV  
Source  
Swap  
Source  
Swap  
Quick way to access swapping: Just press the “SWAP” button under  
the cover of the remote control.  
Quick way to access the PIP size: Just press the “SIZE” button  
under the cover of the remote control.  
Size  
Large  
Ant  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Locate  
Ant/CATV  
Channel  
Ant  
5
Ant  
5
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Swap,  
then press the ENTER button.  
The image in the PIP window will appear on the  
main screen, and vice versa.  
Press the UP or DOWN button to select “Size”.  
PIP  
PIP  
Select  
On  
TV  
2
3
2
3
4
Select  
On  
TV  
Source  
Swap  
Source  
Swap  
Size  
Large  
Ant  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Locate  
Ant/CATV  
Channel  
Ant  
5
Ant  
5
Move  
Select  
Menu  
Move  
Enter  
Menu  
Press the MENU button to exit.  
Press the LEFT or RIGHT button to select “Small”,  
“Double” or “Large”.  
PIP  
Select  
On  
TV  
Source  
Swap  
Size  
Small  
Ant  
Locate  
Ant/CATV  
Channel  
Ant  
5
Move  
Select  
Menu  
Press the MENU button to exit.  
46  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Location of the PIP Image  
Changing the PIP Channel  
Press the MENU button. Press the UP or DOWN  
Press the MENU button. Press the UP or DOWN  
PIP  
PIP  
button to select “PIP”, then press the ENTER button.  
button to select “PIP”, then press the ENTER button.  
1
1
Select  
On  
TV  
Select  
On  
TV  
Source  
Swap  
Source  
Swap  
Size  
Large  
Ant  
Size  
Large  
Ant  
Quick way to change the PIP channel: Just press the “CH  
or  
Locate  
Ant/CATV  
Channel  
Locate  
Ant/CATV  
Channel  
CHbutton under the cover of the remote control.  
Ant  
5
Ant  
5
Move  
Select  
Select  
Select  
Menu  
Menu  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Locate”.  
Press the UP or DOWN button to select “Ant/ CATV”  
Press the LEFT or RIGHT button to select “Ant”,  
“STD”, “HRD” or “IRC”.  
.
PIP  
PIP  
2
2
3
4
Select  
On  
TV  
Select  
On  
TV  
Source  
Swap  
Source  
Swap  
Size  
Large  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Locate  
Ant/CATV  
Channel  
STD  
STD  
5
Ant  
5
Move  
Select  
Menu  
Move  
Press the LEFT or RIGHT button to move the PIP  
Press the UP or DOWN button to select “Channel”.  
Press the LEFT or RIGHT button to change the  
channel that appears in the PIP window.  
PIP  
PIP  
screen where you want.  
3
Select  
On  
TV  
Select  
On  
TV  
Source  
Swap  
Source  
Swap  
Size  
Large  
Size  
Large  
Ant  
Locate  
Ant/CATV  
Channel  
Locate  
Ant/CATV  
Channel  
STD  
STD  
9
Ant  
5
Move  
Select  
Menu  
Move  
Press the MENU button to exit.  
Press the MENU button to exit.  
4
48  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ch a n g in g th e Scre e n Size  
Ch a n g in g th e Scre e n Size  
When you press the ASPECT button on the remote control, the PDPs screen mode should appear in  
sequence. The screen displays in this order: Wide, Panorama, Zoom1, Zoom2, Normal.  
Still  
Press the Still button on the remote control to freeze a  
moving picture. Press again to cancel.  
Note  
If you watch a still image or the Normal (4:3) mode for a long time (over 2 hours), an image may  
be burned onto the screen. View the monitor in Wide or Panorama mode as much as possible.  
Wide  
Zoom2  
Sets the picture to 16:9 wide mode.  
The screen size when the Zoom1 screen is  
vertically enlarged.  
Wide  
Zoom2  
Up/Down  
Panorama  
Normal (4:3)  
Converts regular 4:3 aspect ratio screen to  
wide screen.  
Sets the picture to 4:3 normal mode.  
Panorama  
Normal  
Zoom1  
The screen size when Wide screen is vertically  
enlarged.  
Zoom1  
Up/Down  
Notes  
In TV, VIDEO, S-VIDEO and Component(480i) modes, all screen modes can be selected.  
(Wide Panorama ✱✱ Zoom1 ✱✱ Zoom2 Normal).  
In PC/ DVI mode, only Wide & Normal modes can be selected.  
In Component(480p, 720p. 1080i) modes, Panorama mode cant be selected.  
In Component(480p, 720p. 1080i) modes, you can move the picture on screen by pressing  
the Upor Downbutton. (All screen modes)  
Changing the screen size to Normal, Zoom1 or Zoom2 during PIP mode will cause the PIP  
window to disappear.  
50  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
So u n d Co n tro l  
Customizing the Sound ................................................................54  
Using Automatic Sound Settings ....................................................55  
Choosing a Multi-Channel Sound (MTS)Soundtrack ..........................56  
Using the Auto Volume ..................................................................57  
Using Dolby Virtual ......................................................................58  
Using a Subwoofer ......................................................................59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cu sto m izin g th e So u n d  
Usin g Au to m a tic So u n d Se ttin g s  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Sound  
Custom  
Sound  
Custom  
Mode  
1
2
3
1
2
3
Mode  
Adjust  
Adjust  
MTS  
Mono  
Off  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Adjust”,  
then press the ENTER button.  
You will also see the items “Bass”, “Treble” and  
Balance”.  
Press the LEFT or RIGHT button to select “Adjust”,  
“Standard”, “Music”, “Movie” or “Speech” sound  
setting.  
Sound  
Music  
Sound  
Custom  
Mode  
Mode  
Adjust  
Adjust  
MTS  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Move  
Select  
Menu  
Move  
Enter  
Menu  
Press the UP or DOWN button to select the item you  
wish to change.  
Press the MENU button to exit.  
Adjust  
Bass  
50  
Treble  
Balance  
50  
L 50  
R 50  
Move  
Adjust  
Menu  
Press the LEFT or RIGHT button to change the value  
of the item.  
4
5
Bass  
82  
Press the MENU button to exit.  
54  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ch o o sin g a Mu lti-Ch a n n e l So u n d (MTS)  
So u n d tra ck  
Usin g th e Au to Vo lu m e  
Each broadcasting station has its own signal conditions, which can make it necessary to  
adjust the volume every time the channel is changed. “Auto volume” lets you automatically  
adjust the volume of the desired channel by lowering the sound output when the modula-  
tion signal is high or by raising the sound output when the modulation signal is low.  
Depending on the particular program being broadcast, you can listen to stereo, mono,  
or a Separate Audio Program. (SAP audio is usually a foreign-language translation.  
Sometimes SAP has unrelated information like news or weather.)  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Sound  
Custom  
Sound  
Custom  
Mode  
Mode  
1
2
3
4
1
2
3
Adjust  
Adjust  
MTS  
Mono  
Off  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Off  
Quick way to access the MTS menu: Just press the “MTS” button on  
the remote control.  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “MTS”.  
Press the UP or DOWN button to select “Auto  
Volume”.  
Sound  
Sound  
Mode  
Standard  
Mode  
Standard  
Adjust  
Adjust  
MTS  
Mono  
Off  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the LEFT or RIGHT button to select “Mono”,  
“Stereo” or “SAP”.  
Press the LEFT or RIGHT button to select “On”.  
Sound  
Standard  
Sound  
Standard  
Mode  
Mode  
Adjust  
• Pressing the LEFT or RIGHT button will alternate  
between “Onand “Off.”  
Adjust  
MTS  
Stereo  
Off  
MTS  
Mono  
On  
Auto Volume  
Dolby Virtual  
Woofer  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
Press the MENU button to exit.  
4
Choose Stereo for channels that are broadcasting in stereo.  
Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving  
a stereo signal.  
Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation.  
Note  
The MTS function operates in TV mode only.  
56  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usin g Do lb y Virtu a l  
Usin g a Su b w o o fe r  
This feature allows the PDP’s optional L/ R speakers to provide a Home Theater-like Dolby  
effect. The center and surround sounds are mixed into the L/ R speakers.  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Sound  
Custom  
1
2
3
4
Mode  
Adjust  
Press the MENU button. Press the UP or DOWN  
button to select “Sound”, then press the ENTER  
button.  
Sound  
Custom  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Mode  
1
2
3
4
Off  
Adjust  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
Move  
Select  
Menu  
Off  
Quick way to access the Surround: Just press the “SURROUND”  
button on the remote control.  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Woofer”,  
then press the ENTER button.  
Sound  
Mode  
Standard  
Adjust  
MTS  
Mono  
Off  
Press the UP or DOWN button to select “Dolby  
Virtual”.  
Auto Volume  
Dolby Virtual  
Woofer  
Sound  
Off  
Mode  
Standard  
Adjust  
MTS  
Mono  
Off  
Move  
Enter  
Menu  
Auto Volume  
Dolby Virtual  
Woofer  
Off  
Press the LEFT or RIGHT button to select “On”.  
Woofer  
On  
Move  
Select  
Menu  
Woofer  
• Pressing the LEFT or RIGHT button will alternate  
between “Onand “Off.”  
Volume  
50  
Cutoff Freq.  
120Hz  
Press the LEFT or RIGHT button to select “On”.  
Sound  
Standard  
Mode  
Move  
Select  
Menu  
• Pressing the LEFT or RIGHT button will alternate  
between “Onand “Off.”  
Adjust  
MTS  
Mono  
Off  
Auto Volume  
Dolby Virtual  
Woofer  
On  
Press the UP or DOWN button to select “Volume”,  
then press the LEFT or RIGHT button to adjust the  
value of the item.  
Woofer  
Woofer  
On  
Move  
Select  
Menu  
Volume  
50  
Cutoff Freq.  
120Hz  
This sets the volume for the subwoofer.  
Press the MENU button to exit.  
Move  
Adjust  
Menu  
Volume  
65  
Press the UP or DOWN button to select “Cutoff  
Freq.”, then press the LEFT or RIGHT button to adjust  
the value of the item.  
This sets the cutoff frequency for the subwoofer.  
For example, if you set the cutoff frequency at  
130Hz, the subwoofer will reproduce frequencies  
of 130Hz and lower.  
Woofer  
On  
5
6
Woofer  
Volume  
50  
Cutoff Freq.  
130Hz  
Move  
Adjust  
Menu  
Press the MENU button to exit.  
58  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Cha nnel Control  
Fine Tuning Channels....................................................................62  
LNA (Low Noise Amplifier)............................................................63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fin e Tu n in g Ch a n n e ls  
LN A (Lo w N o ise Am p lifie r)  
Use fine tuning to manually adjust a particular channel for optimal reception.  
If the TV is operating in a weak-signal area, sometimes the LNA function can improve  
the reception (a low-noise preamplifier boosts the incoming signal).  
Press the MENU button. Press the UP or DOWN  
button to select “Channel”, then press the ENTER  
button.  
Press the MENU button. Press the UP or DOWN  
button to select “Channel”, then press the ENTER  
button.  
Channel  
Ant  
Channel  
Ant  
1
2
3
4
1
2
3
4
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
Ant/ CATV  
Auto Program  
Fine Tune  
LNA  
0
0
Off  
Off  
Ch. Scan  
Ch. Scan  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Fine  
Tune”.  
Press the UP or DOWN button to select “LNA”.  
Channel  
Air  
Channel  
Air  
Air / CATV  
Auto Program  
Fine Tune  
LNA  
Air / CATV  
Auto Program  
Fine Tune  
LNA  
0
0
Off  
Off  
Ch. Scan  
Ch. Scan  
Move  
Adjust  
Menu  
Move  
Select  
Menu  
Press the LEFT or RIGHT button to adjust the fine  
tuning.  
Press the LEFT or RIGHT button to select “On.”  
Channel  
Air  
Channel  
Air  
Air / CATV  
Auto Program  
Fine Tune  
LNA  
Air / CATV  
Auto Program  
Fine Tune  
LNA  
• Pressing the LEFT or RIGHT button will alternate  
between “Onand “Off.”  
+3  
0
Off  
On  
Ch. Scan  
Ch. Scan  
Add/Erase  
Adjust  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
To store the fine tuning setting in the TV’s memory,  
press the UP button.(A star icon<*>will appear.)  
To reset the fine tuning to “0, press the DOWN  
button.  
Channel  
Air  
Air / CATV  
Auto Program  
Fine Tune  
LNA  
+3  
Off  
Ch. Scan  
Add/Erase  
Adjust  
Menu  
Press the MENU button to exit.  
5
62  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Connecting a PC a nd Opera tion  
Connecting to a PC ......................................................................66  
Adjusting the PC Screen................................................................70  
Changing the Position of the Image ................................................71  
Changing the Size of the Image ....................................................72  
Information ..................................................................................73  
Picture Quality Adjustment ............................................................74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g to a PC  
Connection to a Macintosh computer may require in adapter.  
PDP  
Pin Configuration  
D-Su b Ca b le  
15Pin Signal Cable (based on protruded pin)  
DVI-D Ca b le (Dig ita l-O n ly Co n n e cto r)  
Power Plug  
Ferrite Cores(HPN5039)  
Use the DVI-D  
connection cable.  
(sold separately)  
or  
DVI Cable  
PC Cable  
Audio Cable  
PC  
Setting up Your PDP (Plug and Play)  
Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming  
setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual  
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your  
display. This monitor automatically tells the PC system its Extended Display Identification data (EDID)  
using Display Data Channel (DDC) protocols.  
DVI jack  
(The actual config-  
uration on your PC  
may be different,  
depending on the  
model.)  
Connecting a PC to the PDP  
Connect a PC (15pin) cable between the PC Output jack (or DVI jack) on the PC and the  
RGB IN(or DVI IN) Input jack (15p D-SUB) on the PDP.  
1
2
Connect a Audio cable between the Audio (RGB or DVI) on the PC and the Audio L/ R (RGB  
or DVI) input jacks on the PDP.  
To watch the PC screen:  
1. Turn on your PDP, and press the TV/ VIDEO button on the remote control.  
2. Press the UP or DOWN button to select “PC”, then press the ENTER button.  
3. Turn on PC and check for PC system requirements. (Refer to pages 66 and 67  
for PC system requirements.)  
4. Adjust the PC screen. (Refer to pages 70 and 76.)  
66  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes:  
Both screen position and size will vary, depending on the type of PC monitor and its resolution.  
The table below shows all of the display modes that are supported:  
How to Set up Your PC Software (Windows only)  
The Windows display-settings for a typical computer are shown below. However, the actual screens  
on your PC will probably be different, depending upon your particular version of Windows and your  
particular video card. But even if your actual screens look different, the same, basic set-up information  
will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)  
Vertical Horizontal  
Frequency (Hz) Frequency (KHz)  
Vertical  
polarity  
Horizontal  
polarity  
Video signal  
Dot X Line  
640 X 350  
70.086  
85.080  
70.087  
85.039  
59.940  
72.809  
75.000  
85.008  
56.250  
60.317  
72.188  
75.000  
85.061  
60.004  
70.069  
75.029  
84.997  
60.000  
60.020  
31.469  
37.861  
31.469  
37.927  
31.469  
37.861  
37.500  
43.269  
42.925  
37.879  
48.077  
46.875  
53.674  
48.363  
56.476  
60.023  
68.677  
47.700  
63.981  
N
N
P
P
P
On the windows screen, select in the following  
sequence : Start Settings Control Panel.  
720 X 400  
640 X 480  
N
N
N
N
N
N
N/ P  
P
P
P
N
N
N
N/ P  
P
IBM PC / AT  
Compatible  
800 X 600  
P
P
P
P
P
P
When the control panel screen appears, click on  
“Displayand a display dialog-box will appear.  
1024 X 768  
N
N
P
N
N
P
P
P
1280 X 768*  
P
N
P
1280 X 1024*  
P
Support only 1280 X 768 mode of W-XGA formats.  
The interlace mode is not supported.  
Select the “Settings” tab in the display dialog-  
box.  
The PDP operates abnormally if a non-standard video format is selected.  
The two key variables that apply to the PDP-PC  
interface are “resolution” and “colors”.  
The correct settings for these two variables are:  
Notes:  
When this PDP is used as a PC display, 32-bit color is supported.  
Depending on the manufacturer, your PC display screen might appear different.  
(and depending on your particular version of Windows).  
Size (sometimes called “resolution”)  
:1024 X 768 pixels  
Check your PC instruction book for information about connecting your PC to a PDP.  
If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHZ  
(horizontal).  
Color: “24-bit” color (might also be expre-  
ssed as 16 million colors”)Shown at left is  
a typical screen for “Display” dialog box.  
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power  
is turned off (or if the PC is disconnected). If so, press the TV/ VIDEO button to enter the VIDEO  
mode. Also, make sure that the PC is connected.  
If a vertical-frequency option exists on your  
display settings dialog box, the correct value is  
60” or “60 Hz.” Otherwise, just click “OK”  
and exit the dialog box.  
Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise,  
random signals might appear).  
When DVI is selected as an input, * mode is not supported.  
When this TV is connected to PC, there are some cases that DOS mode or CMOS BIOS mode is not  
perfectly compatible with some PCs. However, this is not a fault.  
Continued...  
68  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ad ju stin g th e PC Scre e n  
Ch a n g in g th e Po sitio n o f th e Im a g e  
After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned.  
Adjusting the R.G.B  
Pre se t:  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Pre se t:  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the MENU button. Press the UP or DOWN  
button to select PC, then press the ENTER button.  
PC  
1
Position  
Adjust  
Press the MENU button, then press the ENTER  
button.  
Picture  
Custom  
Scaling  
Wide  
Information  
Auto Adjust  
1
Mode  
Adjust  
Color Tone  
Color Adjust  
DNIe  
Custom  
On  
Move  
Enter  
Menu  
Move  
Select  
Menu  
Press the MENU button, then adjust the screen posi-  
tion by using the UP/ DOWN/ LEFT/ RIGHT button.  
Position  
2
3
Press the UP or DOWN button to select Color  
Tone, then Press the LEFT or RIGHT button to select  
Custom. When Customis selected, the word  
Color Adjustwill appear on the screen.  
Picture  
Custom  
2
3
4
Mode  
Adjust  
Color Tone  
Color Adjust  
DNIe  
Custom  
On  
Move  
Move  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
Press the UP or DOWN button to select Color  
Adjust, then press the ENTER button.  
Picture  
Custom  
Mode  
Adjust  
Color Tone  
Color Adjust  
DNIe  
Custom  
On  
Move  
Enter  
Menu  
Press the UP or DOWN button to select the item you  
want to change, then press the RIGHT or LEFT  
button to change the value of the item, using the  
on-screen gauge as your guide.  
Adjust  
Red  
50  
50  
50  
Green  
Blue  
Move  
Adjust  
Menu  
Red  
82  
Press the MENU button to exit.  
5
70  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ch a n g in g th e Size o f th e Im a g e  
In fo rm a tio n  
Pre se t:  
Pre se t:  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the MENU button. Press the UP or DOWN  
Press the MENU button. Press the UP or DOWN  
PC  
PC  
button to select PC, then press the ENTER button.  
button to select PC, then press the ENTER button.  
1
1
Position  
Position  
Adjust  
Adjust  
Scaling  
Wide  
Scaling  
Wide  
Information  
Auto Adjust  
Information  
Auto Adjust  
Move  
Enter  
Menu  
Move  
Enter  
Menu  
Press the UP or DOWN button to select Scaling.  
Press the UP or DOWN button to select Informa-  
tion, then press the ENTER button.  
The vertical, horizontal frequencies and resolution  
appear.  
PC  
PC  
2
3
4
Position  
2
Position  
Adjust  
Adjust  
Scaling  
Wide  
Scaling  
Wide  
Information  
Auto Adjust  
Information  
Auto Adjust  
Move  
Select  
Menu  
Move  
Enter  
Menu  
Information  
Press the LEFT or RIGHT button to select Wide”  
or Normal.  
PC  
Position  
Resolution  
:
:
:
1024  
*
768  
Adjust  
H-Frequency  
V-Frequency  
48.52 KHz  
60.21 Hz  
Scaling  
Normal  
Information  
Auto Adjust  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
Press the MENU button to exit.  
3
72  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pictu re Q u a lity Ad ju stm e n t  
Picture Automatic Adjustment  
Coarse Adjustment  
Pre se t:  
Pre se t:  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the MENU button. Press the UP or DOWN  
Press the MENU button. Press the UP or DOWN  
PC  
PC  
button to select PC, then press the ENTER button.  
button to select PC, then press the ENTER button.  
1
1
Position  
Position  
Adjust  
Adjust  
Scaling  
Wide  
Scaling  
Wide  
Information  
Auto Adjust  
Information  
Auto Adjust  
Move  
Enter  
Menu  
Move  
Enter  
Menu  
Press the UP or DOWN button to select Auto  
Press the UP or DOWN button to select Adjust,  
PC  
PC  
Adjust, then press the ENTER button.  
then press the ENTER button.  
Position  
2
3
4
2
3
Position  
Adjust  
Adjust  
Scaling  
Wide  
Scaling  
Wide  
Information  
Auto Adjust  
Information  
Auto Adjust  
Move  
Enter  
Menu  
Move  
Enter  
Menu  
The message Auto Adjustappears on the screen  
and the picture adjustments are automatically  
activated.  
Press the UP or DOWN button to select Coarse.  
Adjust  
50  
7
Corase  
Fine  
Remove picture noise (vertical stripes) on the screen  
by pressing the LEFT or RIGHT button. (If Coarse is  
not set properly, vertical stripes will appear on the  
screen.)  
Auto Adjust  
Move  
Adjust  
Menu  
Press the MENU button to exit.  
Coarse  
53  
Press the MENU button to exit.  
4
74  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fine Tuning (Fine)  
Pre se t:  
Press the TV/ VIDEO button, then press the UP or DOWN button to select PC.  
Press the ENTER button to select PC mode.  
Press the MENU button. Press the UP or DOWN  
button to select “PC”, then press the ENTER button.  
PC  
1
Position  
Adjust  
Scaling  
Wide  
Information  
Auto Adjust  
Move  
Enter  
Menu  
Press the UP or DOWN button to select “Adjust”,  
then press the ENTER button.  
PC  
2
3
Position  
Adjust  
Scaling  
Wide  
Information  
Auto Adjust  
Move  
Enter  
Menu  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Press the UP or DOWN button to select “Fine”.  
Adjust  
50  
7
Corase  
Fine  
Remove picture noise on the screen by pressing the  
LEFT or RIGHT button. (If Fine is not set properly,  
noise will appear on the screen.)  
Tim e Se ttin g  
Move  
Adjust  
Menu  
Setting the Clock .......................................................................78  
Setting the Sleep Timer...............................................................79  
Setting the Timers ......................................................................80  
Setting the Preferred Channel and Volume Level ............................82  
Fine  
53  
Press the MENU button to exit.  
4
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se ttin g th e Clo ck  
Se ttin g th e Sle e p Tim e r  
You can set your PDP to automatically turn off after a preset interval.  
Press the MENU button. Press the UP or DOWN  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
Function  
English  
button to select “Function”, then press the ENTER  
button.  
1
2
3
4
Language  
Time  
1
Language  
Time  
Caption  
NR  
Caption  
NR  
Off  
Off  
Off  
Off  
Quick way to access the sleep timer: Just press the “SLEEP” button  
on the remote control.  
Auto Power Off  
V-Chip  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Film Mode  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Time”, then  
press the ENTER button.  
Press the UP or DOWN button to select “Time”, then  
press the ENTER button.  
Function  
English  
Function  
English  
2
3
4
5
Language  
Time  
Language  
Time  
Caption  
NR  
Caption  
NR  
Off  
Off  
Off  
Off  
Auto Power Off  
V-Chip  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Film Mode  
Off  
Move  
Enter  
Menu  
Move  
Enter  
Menu  
Press the LEFT or RIGHT button to select hour, then  
press the UP or DOWN button to select the correct  
hour.  
Press the UP or DOWN button to select “Sleep”.  
Time  
Time  
Clock  
10 : 30 am  
Clock  
10  
--  
--  
:
:
:
-- am  
-- am  
-- am  
On Time  
--  
--  
:
:
-- am  
-- am  
Off  
Off  
Off  
10  
3
On Time  
Off  
Off  
Off  
10  
3
Off Time  
Off Time  
Sleep  
Sleep  
On Time Volume  
On Time Channel  
On Time Volume  
On time Channel  
Move  
Select  
Menu  
Adjust  
Move  
Menu  
Press the LEFT or RIGHT button to select minute, then  
press the UP or DOWN button to select the correct  
minute.  
Press the LEFT or RIGHT button to select the time  
interval for the PDP to stay on. The interval ranges  
from 10 to 180 minutes.  
Time  
Time  
Clock  
10 : 30 am  
Clock  
10 : 30 am  
On Time  
--  
--  
:
:
-- am  
-- am  
Off  
Off  
Off  
10  
3
On Time  
--  
--  
:
:
-- am  
-- am  
Off  
Off  
30  
10  
3
Off Time  
Off Time  
Sleep  
Sleep  
On Time Volume  
On time Channel  
On Time Volume  
On Time Channel  
Adjust  
Move  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
Press the MENU button to exit.  
5
Note  
Time setting will be reset when you pull out the Power cord if the PDP is ON.  
(If you want to keep the time setting, turn the PDP off using the POWER button on the remote control  
or the Front Panel.)  
78  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se ttin g th e Tim e rs  
This PDP can be set to turn on or off automatically at specific times that you choose. Before  
using the timers, you must set the PDPs clock, as described previously.  
Setting the On/ Off Timer  
Press the LEFT or RIGHT button to select “Off” or  
On”, then press the UP or DOWN button to select  
Off” or “On”.  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Time  
Function  
English  
6
7
Clock  
10 : 30 am  
1
2
3
4
5
Language  
Time  
On Time  
7
: 30 am  
On  
Off  
Off  
10  
3
Off Time  
-- : -- am  
Caption  
NR  
Sleep  
Off  
Off  
On Time Volume  
On time Channel  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Adjust  
Move  
Menu  
Move  
Select  
Menu  
If you want to set Off Time, press the UP or DOWN  
button to select the “Off Time”.  
Set the “Off Time” just as you set “On Time”.  
Press the UP or DOWN button to select “Time”, then  
press the ENTER button.  
Time  
Function  
English  
Clock  
12 : 00 am  
Language  
Time  
On Time  
7
: 30 am  
On  
Off  
Off  
10  
3
Off Time  
-- : -- am  
Caption  
NR  
Sleep  
Off  
Off  
On Time Volume  
On Time Channel  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Select  
Menu  
Move  
Enter  
Menu  
Press the MENU button to exit.  
Press the UP or DOWN button to select “On Time”.  
Time  
8
Clock  
10 : 30 am  
On Time  
--  
--  
:
:
-- am  
-- am  
Off  
Off  
Off  
10  
3
Off Time  
Sleep  
On Time Volume  
On time Channel  
Note  
Move  
Select  
Menu  
If you set to On Time or Off Time, the Power Indicator on the Front Panel is changed to Green.  
Press the LEFT or RIGHT button to select hour, then  
press the UP or DOWN button to select the correct  
hour.  
Time  
Clock  
10 : 30 am  
On Time  
7
--  
:
:
-- am  
-- am  
Off  
Off  
Off  
10  
3
Off Time  
Sleep  
On Time Volume  
On time Channel  
Adjust  
Move  
Menu  
Press the LEFT or RIGHT button to select minute, then  
press the UP or DOWN button to select the correct  
minute.  
Time  
Clock  
10 : 30 am  
On Time  
7
: 30 am  
Off  
Off  
Off  
10  
3
Off Time  
-- : -- am  
Sleep  
On Time Volume  
On time Channel  
Adjust  
Move  
Menu  
80  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se ttin g th e Pre fe rre d Ch a n n e l  
a n d Vo lu m e Le ve l  
The preferred channel and volume can be set for when the timer automatically turns on the TV.  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
1
2
3
4
Language  
Time  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Select  
Menu  
Press the UP or DOWN button to select “Time”, then  
press the ENTER button.  
Function  
English  
Language  
Time  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Enter  
Menu  
Press the UP or DOWN button to select “On Time  
Volume”.  
Press the LEFT or RIGHT button to adjust volume  
level.  
Time  
Clock  
--  
--  
--  
:
:
:
-- am  
-- am  
-- am  
On Time  
Off  
Off  
Off  
10  
3
Off Time  
Sleep  
On Time Volume  
On Time Channel  
Move  
Select  
Menu  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Press the UP or DOWN button to select “On Time  
Channel”.  
Press the LEFT or RIGHT button to select the channel.  
Time  
Clock  
--  
--  
--  
:
:
:
-- am  
-- am  
-- am  
On Time  
Off Time  
Sleep  
Off  
Off  
Off  
10  
3
Fu n ctio n De scrip tio n  
On Time Volume  
On Time Channel  
Selecting a Menu Language .....................................................84  
Viewing Closed Captions .........................................................85  
Digital Noise Reduction ...........................................................86  
Setting Auto Power Off ...........................................................87  
Using the V-Chip .....................................................................88  
Selecting the Film Mode ...........................................................94  
Move  
Select  
Menu  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se le ctin g a Me n u La n g u a g e  
Vie w in g Clo se d Ca p tio n s  
Your TV decodes and displays the closed captions that are broadcast with certain  
TV shows. These captions are usually subtitles for the hearing impaired or foreign-  
language translations. All VCRs record the closed caption signal from television  
programs, so home-recorded video tapes also provide closed captions. Most pre-  
recorded commercial video tapes provide closed captions as well. Check for the  
closed caption symbol in your television schedule and on the tapes packaging:  
Note: The Caption feature does not work with DVD or DTV signals.  
.
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
Language  
Time  
1
2
3
Caption  
NR  
Off  
Off  
Press the MENU button. Press the UP or DOWN  
Function  
English  
Auto Power Off  
V-Chip  
button to select “Function”, then press the ENTER  
button.  
1
2
3
4
Language  
Time  
Film Mode  
Off  
Move  
Select  
Menu  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Select  
Menu  
Press the LEFT or RIGHT button to select the appro-  
priate language : English, Français or Español.  
Press the UP or DOWN button to select “Caption”,  
then press the ENTER button.  
Function  
English  
Language  
Time  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Enter  
Menu  
Press the MENU button to exit.  
Press the LEFT or RIGHT button to turn closed cap-  
tioning On/ Off.  
Caption  
Caption  
Mode  
On  
Caption  
Channel  
Field  
2
1
Move  
Select  
Menu  
Press the UP or DOWN button to select “Mode”,  
then press the LEFT or RIGHT button to select  
“Caption” or “Text.”  
Caption  
Caption  
Mode  
On  
Text  
2
Channel  
Field  
1
Move  
Select  
Menu  
Depending on the particular broadcast, it might be  
necessary to make changes to “Channels” and  
Field”: Press the UP/ DOWN/ LEFT/ RIGHT button  
to make the changes. (Follow the same procedure  
as in steps 3~4 above.)  
5
Press the MENU button to exit.  
Note  
Different channels and fields display different information: Field 2 carries additional information  
that supplements the information in Field 1. (For example, Channel 1 may have subtitles in English,  
while Channel 2 has subtitles in Spanish.  
84  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dig ita l N o ise Re d u ctio n  
Se ttin g Au to Po w e r O ff  
If the broadcast signal received by your TV is weak, you can activate the Digital Noise  
Reduction feature to help reduce any static and ghosting that may appear on the screen.  
The PDP can be set to turn off automatically if no buttons are pressed for 3 hours  
after the PDP turns on via the On timer.  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
Function  
English  
Language  
Time  
Language  
Time  
1
2
3
4
1
2
3
Caption  
NR  
Caption  
NR  
Off  
Off  
Off  
Off  
Auto Power Off  
V-Chip  
Auto Power Off  
V-Chip  
Film Mode  
Film Mode  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the UP or DOWN button to select “NR.  
Press the LEFT or RIGHT button to select “On”.  
Press the MENU button to exit.  
Press the UP or DOWN button to select “Auto  
Power Off”.  
Function  
English  
Function  
English  
Language  
Time  
Language  
Time  
Caption  
NR  
Caption  
NR  
Off  
Off  
Off  
Off  
Auto Power Off  
V-Chip  
Auto Power Off  
V-Chip  
Film Mode  
Film Mode  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the LEFT or RIGHT button to select “On”.  
Function  
English  
Function  
English  
Language  
Time  
Language  
Time  
Caption  
NR  
Caption  
NR  
On  
Off  
Off  
On  
Auto Power Off  
V-Chip  
Auto Power Off  
V-Chip  
Film Mode  
Film Mode  
Off  
Off  
Move  
Select  
Menu  
Move  
Select  
Menu  
Press the MENU button to exit.  
4
Note  
If the Off timer is set, Auto Power Off will not function.  
The power will be turned off automatically after 15 minutes if the PDP is ON and there is no input  
signal. (For instance, if you select a channel without a signal while in TV mode or when there is no  
input signal after selecting an output signal)  
86  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usin g th e V-Ch ip  
The V-Chip feature automatically locks out programs that are deemed inappropriate  
for children. The user must enter a PIN (personal ID number) before any of the V-Chip  
restrictions are set up or changed.  
Note : When the V-chip feature is activated, the PIP and auto channel program features  
do not function.  
How to Enable/Disable the V-Chip  
Setting Up Your Personal ID Number (PIN)  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
1
Language  
Time  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
Caption  
NR  
Off  
Off  
1
Language  
Time  
Auto Power Off  
V-Chip  
Caption  
NR  
Film Mode  
Off  
Off  
Off  
Move  
Select  
Menu  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Select  
Menu  
Press the UP or DOWN button to select “V-Chip”,  
Function  
English  
then press the ENTER button.  
2
Language  
Time  
Press the UP or DOWN button to select “V-Chip”,  
then press the ENTER button.  
Function  
English  
Caption  
NR  
Off  
On  
2
Language  
Time  
Auto Power Off  
V-Chip  
Caption  
NR  
Film Mode  
Off  
Off  
On  
Move  
Enter  
Menu  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Enter  
Menu  
The message "Enter Pin" will appear. Enter your  
V-Chip  
4-digit PIN number.  
3
Enter Pin  
Enter Pin  
The message "Enter Pin" will appear. Enter your  
4-digit PIN number.  
V-Chip  
:
----  
3
4
Enter Pin  
Enter Pin  
Note: The default PIN number of a new TV set is  
0-0-0-0.”  
:
----  
The “V-Chip” screen will appear.  
To enable the V-Chip feature, press the RIGHT button  
so that the “V-Chip Lock” field is Yes.  
(Pressing the left or right button will alternate  
between “Yes” and “No”.)  
V-Chip  
Yes  
4
V-Chip Lock  
TV GuideLines  
MPAA Rating  
Change Pin  
The “V-Chip” screen will appear. Press the UP or  
DOWN button to select “Change Pin,” then press  
the ENTER button.  
V-Chip  
No  
V-Chip Lock  
TV GuideLines  
MPAA Rating  
Change Pin  
Move  
Select  
Menu  
Move  
Enter  
Menu  
Press the MENU button to exit.  
The Change pin screen will appear. Choose any  
4-digits for your PIN and enter them.  
As soon as the 4 digits are entered, the “Confirm  
New Pin” screen appears. Re-enter the same 4  
digits. When the Confirm screen disappears, your  
PIN has been memorized.  
5
V-Chip  
----  
V-Chip  
:
5
Change Pin  
Enter New Pin  
:
Confirm New Pin  
Confirm New Pin  
-
Press the MENU button to exit.  
6
Note  
If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin  
to 0-0-0-0 : Power Off Mute 8 2 4 Power On.  
88  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions Using the “TV guidelines”  
At this point, one of the TV-Ratings is selected.  
Press the RIGHT button : Depending on your existing setup, a letter “U” or “Bwill start  
blinking.  
(U= Unblocked, B= Blocked)  
6
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.)  
Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
While the “U” or ”B” is blinking, press the UP or DOWN button to block or unblock the  
category.  
Press the RIGHT button to save the TV guidelines. A TV-Rating will be selected,  
and no letters will blink.  
Function  
1
Language  
Time  
English  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
To select a different TV-Rating, press the UP or DOWN button and then repeat the process.  
Film Mode  
Off  
Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to  
change any of the following sub-ratings:  
Move  
Select  
Menu  
Press the UP or DOWN button to select “V-Chip”,  
then press the ENTER button.  
FV: Fantasy violence  
D: Sexually Sugessive Dialog  
L: Adult Language  
S: Sexual situation  
V: Violence  
Function  
English  
2
Language  
Time  
Caption  
NR  
Off  
On  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Note 2: The V-Chip will automatically block certain categories that are “more restrictive”.  
For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked.  
Similarly, if you block the TV-G category, then all the categories in the “young adult” group  
will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V) work together  
similarly. (See next section.)  
Move  
Enter  
Menu  
The message "Enter Pin" will appear. Enter your  
4-digit PIN number.  
V-Chip  
3
4
Enter Pin  
Enter Pin  
:
----  
How to set the FV, D, L, S and V sub-ratings.  
First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on  
previous page).  
Next, while the TV-Rating is selected, repeatedly press the RIGHT button.  
This will cycle through the available sub-ratings (FV,L, S, D or V).  
A blinking letter (“U” or “B) will be displayed for each sub-rating. While the “U” or “B” is  
blinking, press the UP or DOWN button to change the sub-rating.  
Press the RIGHT button to save the TV guidelines. A TV-Rating will be selected and no  
letters will select. To select a different TV-Rating, press the UP or DOWN button and then  
repeat the process.  
7
The “V-Chip” screen will appear.  
Press the UP or DOWN button to select “TV Guide-  
Lines”, press the ENTER button.  
V-Chip  
No  
V-Chip Lock  
TV GuideLines  
MPAA Rating  
Change Pin  
Move  
Enter  
Menu  
Note: The V-chip will automatically block certain categories that are “More restrictive”.  
For example, if you block “Lsub-rating in TV-PG, then the “Lsub-ratings in TV-14 and  
TV-MA will automatically be blocked.  
The “TV GuideLines” screen will appear. Press the  
UP or DOWN button to select one of the six age-  
based categories:  
TV GuideLines  
5
All  
U
U
U
U
U
U
FV  
V
S
L
D
TV-Y  
B
U
:
:
Blocked  
Unblocked  
TV-Y7  
TV-G  
U
TV-Y  
Young children  
Press the MENU button to clear all the screens. (Or proceed to the next section, and set up  
additional restrictions based on the MPAA codes).  
TV-PG  
TV-14  
TV-MA  
U
U
U
U
U
U
U
U
U
U
U
TV-Y7  
Children 7 and over  
8
Note  
Move  
Select  
Menu  
TV-G  
General audience  
Parental guidance  
Viewers 14 and over  
Mature audience  
TV-PG  
TV-14  
TV-MA  
Note: These categories consist of two separate groups: TV-Y and TV-Y7 (young children  
through age 7), and TV-G through TV-MA (everybody else). The TV-Y and TV-Y7 categories  
are colored blue.  
The restrictions for these two groups work independently: If a household includes very young  
children as well as young adults, the TV guidelines must be set up separately for each age  
group. (See next step.)  
90  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X  
How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”)  
The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is  
for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objection-  
able ratings (either MPAA or TV-Ratings).  
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank  
and the following message will appear: “Excessive rating.”  
To resume normal viewing, tune to a different channel using the number buttons.  
Under certain conditions (depending on the rating of the local TV programs) the V-Chip might  
lock out all the channels. In this case, use the V.Chip function for an emergency escape”:  
Press the MENU button. Press the UP or DOWN  
Function  
button to select “Function”, then press the ENTER  
button.  
1
2
Language  
Time  
English  
Caption  
NR  
Press the MENU button.  
Off  
Off  
Auto Power Off  
V-Chip  
1
Film Mode  
Off  
Move  
Select  
Menu  
Press the UP or DOWN button to select “V-Chip”, then press the ENTER button.  
2
Press the UP or DOWN button to select “V-Chip”,  
then press the ENTER button.  
Function  
English  
Language  
Time  
Caption  
NR  
Enter your PIN number, and press the RIGHT button to temporarily disable the V-Chip  
Off  
On  
Lock.  
3
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Enter  
Menu  
The message "Enter Pin" will appear. Enter your  
4-digit PIN number.  
V-Chip  
3
4
Enter Pin  
Enter Pin  
:
----  
The “V-Chip” screen will appear. Press the UP or  
DOWN button to select “MPAA Rating,” press the  
V-Chip  
No  
V-Chip Lock  
TV GuideLines  
MPAA Rating  
Change Pin  
ENTER button  
.
Move  
Enter  
Menu  
The “MPAA Rating” screen will appear. MPAA category.  
Pressing the UP or DOWN button will cycle through the  
MPAA categories:  
MPAA Rating  
5
G
U
U
U
U
U
U
U
B
U
:
:
Blocked  
Unblocked  
PG  
PG-13  
R
G
General audience (no restrictions).  
Parental guidance suggested.  
NC-17  
X
PG  
NR  
PG-13 PG-13 (Parents strongly cautioned).  
R (Restricted. Children under 17 should be accompanied by an adult).  
NC-17 No children under age 17.  
Move  
Enter  
Menu  
R
X
X (Adults only).  
Not rated.  
NR  
While a particular category is selected, press the RIGHT button to activate it.  
A selected letter (“U” or “B) will be displayed. Press the UP or DOWN button to select “U” or ”B.  
Press the RIGHT button to save the settings.  
Note: The V-Chip will automatically block any category that is “more restrictive. ”For example,  
if you block the “PG-13” category, then “R, “NC-17” and “Xwill automatically be blocked also.  
92  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se le ctin g th e Film Mo d e  
Press the MENU button. Press the UP or DOWN  
button to select “Function”, then press the ENTER  
button.  
Function  
English  
1
2
3
Language  
Time  
Caption  
NR  
Off  
Off  
Auto Power Off  
V-Chip  
Film Mode  
Off  
Move  
Select  
Menu  
Press the DOWN button to select Film Mode, then  
press the RIGHT or LEFT button to select “On” or  
Off”.  
Function  
English  
Language  
Time  
Caption  
NR  
Off  
Off  
On: Automatically senses and processes film  
signals from all sources and adjusts the  
picture for optimum quality.  
Auto Power Off  
V-Chip  
Film Mode  
On  
Move  
Select  
Menu  
Off: Switches off the Film mode.  
Press the MENU button to exit.  
P
L
A
S
M
A
D
I
S
P
L
A
Y
P
A
N
E
L
Note  
Film mode is supported in Video, S-Video, Component 480i.  
Ap p e n d ix  
Troubleshooting............................................................................96  
Care and Maintenance ................................................................97  
Specifications ..............................................................................98  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ca re a n d Ma in te n a n ce  
Tro u b le sh o o tin g  
With proper care, your PDP will give you many years of service. Please follow these guidelines to get  
the maximum performance from your PDP.  
Before you call a service technician, please scan this list of problems and possible solutions. It may save you  
time and money.  
Identifying Problems  
Do not put the PDP near extremely hot, cold, humid or dusty places.  
Do not put the PDP near appliances that create magnetic fields.  
Keep the ventilation openings clear.  
Problem  
Possible Solution  
Do not place the PDP on a rough and slanted surface, such as cloth or paper.  
Poor picture.  
Check all wire connections.  
Liquids  
Your Remote control does not  
operate the PDP.  
Press the “Mode” button to put your remote control in the “TV”  
mode.  
Do not place liquids near or on the PDP.  
Cabinet  
Never open the cabinet or touch the parts inside.  
Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.  
Do not put heavy objects on top of the cabinet.  
The PDP won’t turn on.  
Check if the power plug is connected.  
There is no screen image.  
Check to see that both the PDP and the source are plugged in  
and turned on.  
Temperature  
If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two  
hours so that moisture that may have formed inside the unit can dry completely.  
The image is too light or  
too dark.  
Adjust the Brightness or Contrast settings.  
Adjust the Size settings.  
The image is too large or  
too small.  
96  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sp e cifica tio n s  
Me m o  
Exterior design and product specifications are subject to change without prior notice to improve  
the performance of this product.  
This PDP applies to Class B digital device.  
(Note: Class B system is for home use.)  
This PDP has been registered for residential use in terms of EMI. So it can be used in all areas as  
well as residential areas.  
HPN5039 (TYPE NO: AX50P3)  
1204.6(W) X 79(D) X 724(H) mm;  
HPN6339 (TYPE NO: AX63P3)  
Model  
1503.4 (W) X 89(D) X 893.8(H) mm;  
Dimensions  
Display  
47.43(W) X 3.11(D) X 28.5(H) inches 59.18(W) X 3.5(D) X 35.18(H) inches  
58 (W) X 21 (D) X 210 (H) mm ; 2.28 (W) X 0.83 (D) X 8.27 (H) inches  
Remote Control  
Display  
43 kg ; 94.79 lbs  
69kg ; 153lbs  
Weight  
Voltage  
{48 kg ; 105.82 lbs (with stand)}  
(82kg ; 181lbs(with stand))  
134g ; 0.295 lbs (including batteries)  
120V, 60Hz  
Remote Control  
Power Consumption  
Number of Pixels  
Screen Size  
400 Watts  
630 Watts  
1366(H) X 768(V)  
159 cm/ 63 inches  
1366(H) X 768(V)  
127 cm/ 50 inches  
ANTENNA input  
VIDEO input  
VHF, UHF (75unbalanced)  
VIDEO  
S-VIDEO  
COMPONENT 1 - 480i / 480p / 720p / 1080i  
COMPONENT 2 - 480i / 480p / 720p / 1080i  
RGB : D-SUB 15P  
DVI  
AUDIO input  
AUDIO output  
VIDEO / S-VIDEO  
COMPONENT 1  
COMPONENT 2  
PC (RGB)  
DVI  
10W + 10W (8 )  
Subwoofer (500mv RMS at 1KHz)  
98  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Caller ID Box 43 948 User Guide
Radio Shack Microphone 33 119 User Guide
Radio Shack Universal Remote 7 in 1 Remote Control with Lighted Keypad User Guide
Raritan Computer Server P2 UMT1664M User Guide
RCA Camcorder EZ2120 User Guide
Remington Hair Clippers SCC 100R User Guide
Roper Digital Camera CoolSnap User Guide
Roper Dishwasher RUD8050S User Guide
Scag Power Equipment Lawn Mower STWC48V 25CV User Guide
Seagate Computer Drive ST980817AM User Guide