Samsung DVR SRD 1676D 1TB User Guide
8 CHANNEL/  
16 CHANNEL DVR  
User Manual  
SRD-876D/1656D/1676D  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
IMPORTANT SAFETY INSTRUCTIONS  
Read these operating instructions carefully before using the unit.  
Follow all the safety instructions listed below.  
Keep these operating instructions handy for future reference.  
1)  
2)  
3)  
4)  
5)  
6)  
7)  
8)  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.  
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
9)  
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two  
blades with one wider than the other. A grounding type plug has two blades and a third grounding  
prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit  
into your outlet, consult an electrician for replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use caution  
when moving the cart/apparatus combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods  
of time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been  
exposed to rain or moisture, does not operate normally, or has been dropped.  
English _3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
BEFORE START  
This manual provides operational information necessary for using the product and contains a description about each  
component part and its function as well as menu or network settings.  
You have to keep in mind the following notices :  
• SAMSUNG retains the copyright on this manual.  
• This manual cannot be copied without SAMSUNG’s prior written approval.  
• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of  
instructions mentioned in this manual.  
• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be  
removed from the unit.  
• Before installing additional HDD or connecting the SATA device to this product, check if it is compatible with the  
product.  
Warning  
Battery  
It is essential that when changing the battery in the unit, the replacement battery must be of the same type  
otherwise there may be a possibility of an explosion.  
The following are the specifications of the battery you are using now.  
• Normal voltage : 3V  
CALIFORNIA USA ONLY  
• Normal capacity : 220mAh  
This Perchlorate warning applies only to primary CR (Manganese Dioxide)  
Lithium coin cells in the product sold or distributed ONLY in California USA.  
• Discharge Current : 0.2mA  
“Perchlorate Material - special handling may apply,  
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”  
• Operating temperature : -20°C ~ +85°C  
(-4°F ~ +185°F)  
Caution  
• Connect the power cord into a grounded outlet.  
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.  
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.  
• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the  
Instructions.  
System Shutdown  
Turning off the power while the product is in operation, or undertaking improper actions may cause damage  
or malfunction to the hard drive or the product.  
To safely cut off power, press the front Power button on the product to display the confirmation message.  
Click <OK> and then unplug the power cable.  
You may want to install a UPS system for safe operation in order to prevent damage caused by an  
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)  
4_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Temperature  
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).  
This product may not work properly if you run right after a long period of storage at a temperature below the  
guaranteed one.  
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand  
at room temperature for a period.  
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).  
Likewise, the hard drive may not work at a temperature below the guaranteed one.  
Ethernet Port  
This equipment is in door use and all the communication wirings are limited to inside of the building.  
Security Precautions  
The default administrator ID is “admin”, and the password must be set when the user log in at the first time.  
Set password for your wireless network if you use the product with a wireless router. Being not protected with  
password or using the default wireless router password may expose your video data to potential threat.  
To prevent from your personal information being exposed, please change your password every 3 months.  
Note that the security and other related issues caused by careless management of password shall be be in the  
charge of the user.  
English _5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
CONTENTS  
3
4
6
8
Important Safety Instructions  
Before Start  
OVERV3IEW  
Contents  
Features  
10 Part Names and Functions (Front)  
12 Part Names and Functions (Rear)  
14 Remote Control  
16 Checking the installation environment  
17 Rack Installation  
INSTALLATION  
17 Installing The HDD  
16  
20 Connecting External Devices  
CONNECTING WITH OTHER2DEV0ICE  
23 Connecting the Network  
25 Getting Started  
28 Live Screen Configuration  
33 Live Mode  
2L5IVE  
35 Spot Out  
36 Zoom  
36 Audio ON/OFF  
36 Freeze  
37 Event Monitoring  
38 System Setup  
MAI3N ME8NU  
48 Setting the Device  
58 Setting the Recording  
61 Setting the Event  
64 Backup  
66 Network Configuration  
79 Controlling a PTZ device  
6_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
82 Search  
SEARCH & PLAY  
85 Playback  
82  
WEB8VIEW7ER  
87 Introducing Web Viewer  
88 Connecting Web Viewer (Windows)  
90 Using Live Viewer (Windows)  
95 Controlling a Connected PTZ Camera  
98 Using Search Viewer  
101 Viewer Setup  
113 About  
114 Connecting Web Viewer (Mac)  
116 Using Live Viewer (Mac)  
117 Mobile Viewer  
118 SEC Backup Viewer  
BACKUP VIEWER  
118  
120 Product Specification  
123 Product Overview  
125 Default Setting  
APPENDIX  
129 Troubleshooting  
120  
132 Open Source Announcement  
English _7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
FEATURES  
The product compresses camera inputs from 8/16 channels with H.264 video codec, and supports simultaneous  
recording and playback of 8/16-channel audio input to/from HDD.  
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and  
audio data.  
• Provides a convenient User Interface  
• 8/16 CH Composite Input Connectors  
• Supports CIF(S)/2CIF(M)/4CIF(L)/WD1/1280H recording formats  
• With the network specific codec, network transfer enabled regardless of the recording conditions  
• Display of HDD information and status by using HDD SMART  
• CODEC performance : 8CH : 240FPS(NTSC)/200FPS(PAL)  
16CH : 480FPS(NTSC)/400FPS(PAL)  
• HDD overwrite function  
• Mass storage HDD backup through high-speed USB 2.0  
• Simultaneous Record and Playback of 8/16-channel video data  
• Various Search Modes (Time, Event, Backup, POS, Motion Detection)  
• Various Recording Modes (Manual, Event, Scheduled Recording)  
• Alarm Interface  
• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer  
• Supports coaxial protocols  
• Tampering Detection  
8_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Standards Approvals  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the  
M
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with  
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a  
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at  
his own expense.  
Package Contents  
Please unwrap the product, and place the product on a flat place or in the place to be installed.  
Please check the following contents are included in addition to the main unit.  
USB  
DVR  
Power Cable  
Remote Control /  
Mouse  
User Manual or Quick Manual  
Remote Control Battery (AAA)  
Network Viewer Software /  
User Manual CD  
Terminal Block (15 pin)  
Bracket Rack  
Terminal Block (20 pin)  
Bracket Fixing Screw  
English _9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
PART NAMES AND FUNCTIONS (FRONT)  
SRD-876D  
a
b
c
d e  
USB  
i
h
g
f
SRD-1656D/1676D  
a
b
c
d e  
USB  
i
h
g
f
Part Names  
Functions  
Channel  
Used to select channel numbers directly in the Live Mode, or numbers in the numeric input mode.  
a
b
REC  
/  
Starts or ends the recording.  
Step Rewind () : Used for backward frame-by-frame search while in PAUSE.  
Fast Rewind () : Used for quick backward search while in Play. (2x-64x)  
Stop : Used to stop the playback.  
Play/Pause : Used to pause or resume the screen.  
►/  
/  
Fast Forward () : Used for quick forward playback. (2x-64x)  
Step Forward () : Used for forward frame-by-frame search while in PAUSE.  
REC : Lights on when recording is in progress.  
HDD : Displays the normal access to HDD.  
Upon access to HDD, LED repeats on and off.  
LED Indicator  
c
ALARM : Lights on when an event occurs.  
NETWORK : Displays both network connection and data transfer status.  
POWER : Displays the power ON/OFF status.  
10_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names  
Functions  
Direction /  
Used to change a value or move the cursor up/down/left/right (ꢀꢁ◄ ►).  
Select Button  
Selects a menu item or executes the selected menu.  
When a scroll bar appears in each menu, acts as a scrolling.  
In Play mode, - Jog : Pauses the playback and steps backward or forward.  
- Shuttle : Fast playback forward or backward.  
d
Jog shuttle  
Used to turn the DVR ON/OFF.  
Power  
e
f
Functions only if the button was held for 3 seconds.  
USB Port  
Connects the USB devices.  
Each time you press the button in Live mode, the screen mode will be switched in sequence.  
MODE  
Each time you press the button in play mode, the screen mode will be switched in sequence.  
AUDIO  
Sets Audio ON/OFF.  
g
ALARM  
MENU/'  
ENTER  
Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the icon.  
Either goes to the system menu screen or moves to the upper menu from the lower menu.  
Runs selected menu function.  
ZOOM : Sets the screen to the x2 digital zoom.  
FREEZE : Runs the FREEZE function in the Live Mode.  
BACKUP : Runs the BACKUP function.  
Camera Control  
OPEN/CLOSE  
h
i
SEARCH : Goes to the search screen.  
Used to open and close the DVR-RW disc tray.  
Using the jog shuttle  
Jog starts from the right point and shuttle starts from the left point.  
< Jog >  
In play mode, DVR playback steps forward video by 1 frame.  
In play mode, DVR playback steps backward video by 1 frame.  
< Shuttle >  
In play mode, DVR plays fast forward.  
In play mode, DVR plays fast reverse.  
English _11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
PART NAMES AND FUNCTIONS (REAR)  
SRD-876D  
a b  
c
d
e
1
2
3
4
5
6
7
8
CH1  
CH3  
CH2  
CH4  
VIDEO IN  
AUDIO IN  
AUDIO OUT  
LOOP OUT  
NETWORK  
SERIAL  
NO  
NC NO  
NO  
NO  
AUDIO IN CH5  
~
CH8  
CONSOLE  
eSATA  
HDMI  
VGA OUT  
USB  
COM  
1
COM COM COM  
G
G
1
2
3
4
5
6
7
8
G
+
-
+
-
2
3
4
ALARM  
RESET  
ALARM OUT  
ALARM IN  
NO CONNECTION  
TX RX  
m
l
k a  
j i h g f  
SRD-1656D/1676D  
a b  
c
d
e
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
CH1  
CH3  
CH2  
CH4  
VIDEO IN  
AUDIO IN  
AUDIO OUT  
LOOP OUT  
NETWORK  
SERIAL  
NO  
NC NO  
NO  
NO  
AUDIO IN CH5  
~
CH16  
CONSOLE  
eSATA  
HDMI  
VGA OUT  
USB  
COM  
1
COM COM COM  
G
G
G
G
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16  
G
+
-
+
-
2
3
4
ALARM  
RESET  
ALARM OUT  
ALARM IN  
TX RX  
m
l
k a  
j i h g f  
Part Names  
AUDIO IN  
AUDIO OUT  
VIDEO IN  
SPOT1/2  
Power  
NETWORK  
USB  
VGA OUT  
HDMI  
Functions  
Audio input signal port (RCA jack) and port for optional audio extension cable.  
Audio Signal Output Port (RCA jack).  
Video Signal Input Port (BNC type connector).  
BNC type of output port for the Spot signal.  
Power connection port.  
a
b
c
d
e
f
g
h
i
NETWORK connector port.  
Connects the USB devices.  
Composite Video Signal Output Port (VGA type connector).  
HDMI connector port.  
12_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names  
eSATA  
LOOP OUT  
Functions  
Ports used for external storage device connections.  
j
k
Terminal used to send the video signal to another device.  
- ALARM IN : Alarm Input port.  
SRD-876D : 1~8 CH  
SRD-1656D/1676D : 1~16 CH  
ALARM  
l
- ALARM RESET : Alarm Reset port.  
- ALARM OUT 1~4 : Alarm Output port.  
RS-485  
SERIAL  
Used to establish RS485 communications. (TX+, TX-, RX+, RX-)  
Serial port for connecting to a POS device.  
m
[CONSOLE] is designed for the service repair purpose only.  
M
English _13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
REMOTE CONTROL  
REC  
POWER  
Starts or ends the live recording.  
Displays the Exit pop up screen.  
+
NUMBER [0~ 10]  
Used as the numeric input keys, or displays a single  
channel.  
ID  
Sets the ID of the system.  
PTZ  
Select 2 digits from 0 ~ 9 while pressing the ID Key.  
Displays or ends PTZ.  
T/W  
SCROLL ,.  
Zooms in or out.  
Moves the menu scroll.  
VIEW  
SEARCH  
Runs the View function in the PTZ mode.  
Displays the search menu.  
MODE  
BACKUP  
Changes the screen mode.  
Displays the Backup Menu.  
RETURN  
MENU  
Returns to the previous screen.  
Goes to the system menu screen.  
Up/Down/Left/Right(▲▼◄ ►)/ENTER  
Moves the cursor up/down/left/right, and runs the  
Select Menu.  
PRESET  
Displays the Preset Setup.  
REC LOCK  
Selects the recording lock function.  
FREEZE  
AUDIO  
Freezes the screen temporarily.  
Turns Audio on/off.  
ZOOM  
Runs the digital zoom (x2) function.  
ALARM  
Cancels the Alarm.  
Skip Backward (by unit time),  
Slow Rewind, Slow Forward,  
Skip Forward (by unit time)  
Move Frame  
While paused, moves to the previous/next frame.  
FR, STOP, PLAY/PAUSE, FF  
14_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Numeric buttons  
CHANNEL 1–9  
CHANNEL 10  
CHANNEL 11–16  
Press each button between 1 to 9.  
Press the [+10] button first, then press the 0 button again within 3 seconds.  
Press the [+10] button first, then press any number between 1 to 6 within 3 seconds.  
Changing the Remote Control ID  
Remote control’s ID and DVR’s ID should be matched for proper operation.  
1. Press the [ID] button of the remote control and check the ID displayed on the DVR screen.  
The factory default ID of the remote control is 00.  
2. Enter 2 digits of your selection in order, while pressing the [ID] button of the remote control.  
3. When ID input is done, press the [ID] button of the remote control again to check the setting.  
If you want to change the remote control ID to 08: Press 0 and 8 in order while the [ID] button of the remote control is pressed.  
M
For changing the ID of remote device, refer to “Remote Devices”. (Page 54)  
English _15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation  
Please take note of the followings before using this product.  
• Do not use the product outdoor.  
• Do not spill water or liquid in the connection part of the product.  
• Do not impose the system to excessive shock or force.  
• Do not pull out the power plug forcefully.  
• Do not disassemble the product on your own.  
• Do not exceed the rated input/output range.  
• Use a certified power cord only.  
• For the product with an input ground, use a grounded power plug.  
CHECKING THE INSTALLATION ENVIRONMENT  
Temperature Unit: ºC  
This product is a top-notch security device that is equipped with a  
high-capacity HDD and other key circuit boards.  
One Year: 24HR X 365 DAY =8,760 HR  
When the temperature rises inside the product, the product may  
breakdown and the product life be shortened. Please pay attention to  
the following recommendations before installation.  
Life (Unit: HOURS)  
[Figure 1]  
When mounting the product on a rack, comply with the following instructions.  
1. Please ensure that the rack inside is not sealed.  
2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.  
3. If you pile up the prudcts or other rack-mount devices as shown in figure 2, secure  
room for ventilation or install a vent.  
D
R
C
D
R
4. For natural air convection, place the inlet at the bottom of the rack and the outlet on top.  
D
V
D
R
E
C
O
5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for  
D
R
UB  
UB  
UB  
USB  
USB  
USB  
USB  
air circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)  
D
V
D
R
E
C
O
D
R
6. Please maintain the temperature inside the rack or surrounding areas between 0°C  
D
V
D
R
E
C
O
D
R
~ 40°C (32°F ~ 104°F) as shown in the figure 1.  
D
D
R
E
C
O
R
D
E
R
Rack Mount Instructions - The following or similar rack-mount instructions are included  
D
R
C
O
R
D
E
R
with the installation instructions :  
D
R
C
O
R
D
E
R
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the  
operating ambient temperature of the rack environment may be greater than room  
ambient. Therefore, consideration should be given to installing the equipment in an  
environment compatible with the maximum ambient temperature (Tma) specified by  
the manufacturer.  
B) Reduced Air Flow - Installation of the equipment in a rack should be such that  
the amount of air flow required for safe operation of the equipment is not  
compromised.  
DVD REO  
RDER  
C) Mechanical Loading - Mounting of the equipment in the rack should be such  
that a hazardous condition is not achieved due to uneven mechanical loading.  
D) Circuit Overloading - Consideration should be given to the connection of the  
equipment to the supply circuit and the effect that overloading of the circuits  
might have on overcurrent protection and supply wiring. Appropriate  
consideration of equipment nameplate ratings should be used when addressing  
this concern.  
DD RECO  
RDR  
[Figure 2]  
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should  
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).  
16_ installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RACK INSTALLATION  
Install the Bracket-Rack as shown in the figure, and then fasten the  
screws on both sides (2 screws on each side).  
Remove the screws on the left and right side of the DVR before installation.  
Fix the screws not to be loosened by vibrations.  
Cautions when Installing in the Rack  
To install multiple DVRs in the rack, make sure to separate the  
FOOT at the bottom of each DVR.  
1. There are four FOOTs at the bottom of a DVR.  
Press the projected parts at both-ends of each “FOOT”  
and turn it counterclockwise.  
2. “FOOT” is separated from the main body when it is turned  
to the end of fastening groove.  
<Separation>  
<Installation>  
INSTALLING THE HDD  
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product  
damage.  
Please consult your provider for further information on HDD installation since improper installation or settings may  
damage the product.  
Make sure to unplug the power cord from the wall outlet before proceeding with the installation.  
Cautions for data loss (HDD care)  
J
Please pay attention so that the data inside the HDD is not damaged.  
Before adding a HDD, please check the compatibility with this product.  
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.  
Please ensure that the HDD is free from such shock.  
We are not liable for any damage to the HDD incurred by user’s carelessness or miss use.  
Cases might cause damage to HDD or recorded data  
To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.  
If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged.  
A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive.  
HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.  
English _17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation  
Cautions on HDD installation  
1. When adding a new HDD, make sure to fasten screws tightly and use appropriate parts if required to fix  
the HDD. Otherwise, the product may be damaged or does not operate properly.  
2. Please check the HDD compatibility before adding a HDD.  
Please contact your nearest dealer to obtain the list of compatible devices.  
Installing the HDD  
If the installed HDD had been used with other devices, it will be automatically formatted.  
J
• Installing HDD by opening the cover  
1. Pull the front cover to open.  
2. Open the front cover and check the HDD mounting  
bracket.  
To prevent from USB ports being damaged, please unplug USB  
devices before openning the front cover.  
J
3. Separate the HDD bracket by pushing the lock on the left.  
Be careful not to scratch the hand while separating the HDD  
J
bracket.  
18_ installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Insert the HDD into the bracket groove. Insert one side first  
and gently lift up the other side.  
5. Align the bracket with installed HDD to the guide of the  
case, push it toward the board.  
Push it firmly until you hear the clicking sound.  
IF it is not fully mounted, HDD detection may fail.  
J
6. You can check the HDD map directly on the DVR.  
Refer to “Storage Device > HDD Map”. (Page 51)  
ꢃ
ꢁ
ꢀ
ꢂ
7. Press it upward so that the front cover is closed.  
• Replacing the mounted HDD  
1. Open the bracket in the direction of arrow to separate the  
b
holder from the HDD.  
2. Open other parts of the bracket wide to separate it from  
the holder.  
a
Remaining instructions after replacing the HDD is same as in  
M
“Installing the HDD”.  
English _19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
connecting with other device  
CONNECTING EXTERNAL DEVICES  
The following figures are based on Model SRD-1656D.  
M
AC 100-240V~IN  
USB  
SPOT1, 2  
HDMI  
VIDEO IN  
AUDIO OUT  
VIDEO OUT (VGA)  
AUDIO IN  
eSATA HDD  
AUDIO IN  
Connecting the USB  
1. By factory default, a USB port is provided for external connection.  
2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.  
3. If a USB HDD is connected to the system, recognition and settings are available in “Main Menu > Device  
>
Storage Device”. (Page 51)  
4. The product supports hot plugging function that enables connecting/disconnecting USB devices while in  
operating the system.  
If the USB storage media for backup is not formatted by the product, format it as FAT32 file system with a PC.  
To prevent from USB ports being damaged, please unplug USB devices before openning the front cover.  
J
20_ connecting with other device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting External SATA HDD (eSATA)  
External SATA port is provided on the rear panel.  
If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “Main Menu >  
Device > Storage Device”.  
Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.  
J
Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the  
device is in use before disconnecting it.  
Connecting POS Device  
You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly  
with a RS-232C cable.  
Connection setup for the RS-232C port is available in “Main Menu > Device > POS Devices”, press the  
<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit>. (Page 55)  
Connecting the Alarm Input/Output  
The Alarm In/Out port at the back is composed of the following.  
SRD-876D  
USB  
8
~
AUDIO IN CH5  
CH  
G
8
7
6
5
4
3
G
1
2
NO CONNECTION  
ALARM IN  
Sensors  
Alarm  
• ALARM IN 1 ~ 8 : Alarm Input Port  
• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and  
resumes sensing.  
• ALARM OUT 1 ~ 4 : Alarm Output Port  
ALARM OUT  
(30VDC 2A,  
ALARM IN  
(5mA sink)  
125VAC 0.5A MAX)  
English _21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
connecting with other device  
SRD-1656D/1676D  
USB  
Sensors  
Alarm  
• ALARM IN 1 ~ 16 : Alarm Input Port  
• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and  
resumes sensing.  
• ALARM OUT 1 ~ 4 : Alarm Output Port  
ALARM OUT  
(30VDC 2A,  
ALARM IN  
(5mA sink)  
ALARM IN  
(5mA sink)  
125VAC 0.5A MAX)  
22_ connecting with other device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the RS-485 Device  
Connect the [TX/RX +, –] device through the back port.  
USB  
system keyboard  
PTZ camera  
You can connect and control the PTZ camera which supports the RS-485 communication.  
M
Check if the RS-485 device is compatible with the product first.  
Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.  
Depending on camera’s type, connection polarity can be different.  
For further information, refer to the respective PTZ Camera’s documentation.  
CONNECTING THE NETWORK  
Connecting to Network through Ethernet (10/100/1000BaseT)  
RJ-45 Ethernet Cable  
USB  
(Direct Cable)  
Hub/Switcher  
Windows  
k Bone  
Bac  
Network Viewer  
NETWORK  
Hub/Switcher  
English _23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
connecting with other device  
Connecting to the Network using the router  
USB  
Broadband Router  
xDSL or Cable Modem  
xDSL or Cable Modem  
External Remote PC  
NETWORK  
DDNS Server  
(Data Center)  
Connecting to Network through PPPoE  
RJ-45 Ethernet Cable  
USB  
(Direct Cable)  
PPPoE MODEM  
Windows  
Phone(PPPoE) Line  
Network Viewer  
NETWORK  
Hub/Switcher  
24_ connecting with other device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
GETTING STARTED  
Starting the system  
1. Connect power cable to the product’s rear.  
2. Touch and hold the front power button for over 3 seconds.  
It takes about 10 seconds to display the start screen after  
M
booting.  
REC  
3. The boot up screen appears.  
Booting up may take about 3 minute, as indicates  
progress with icons.  
If a new HDD is installed, the initialization process may  
take longer.  
REC  
4. The live screen appears with a beep.  
2014-01-01 01:10:25  
English _25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
Shutting Down the System  
You can shut down the system only if you have logged in to the DVR.  
You require permission to shut down the system if you are not logged in as admin.  
1. Hold the [POWER] button on the front or the remote  
2014-01-01 01:10:25  
control for over 3 seconds, or right click and click  
<Shutdown>.  
2. The “Shutdown” confirmation window appears.  
Shutdown  
Are you sure to shutdown?  
3. Use the arrow keys on the remote control or the front  
panel to move to <OK> and press the [ENTER] button or  
click <OK>.  
OK  
Cancel  
The system will shut down.  
For the permission management, refer to “Permission  
M
Management > Setting Permissions”. (Page 43)  
Login  
To access a DVR or restricted menu, you should have logged in to the DVR.  
1. In live mode, right-click any area of the screen.  
You will see the context sensitive menu as in the right  
figure.  
2014-01-01 01:10:25  
Scene Mode  
Spot Out 1  
Spot Out 2  
Audio Off  
Freeze  
Stop Alarm  
Record  
Play  
Search  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Login  
2. Click <Login>.  
2014-01-01 01:10:25  
The login dialog appears.  
You can also see the login dialog to access a desired  
menu by pressing the [MENU] button on the remote  
control or the front panel.  
Login  
ID  
admin  
OK  
Password  
The login dialog will also appear if you press a menu button on the  
remote control or the front panel of the DVR when the corresponding  
menu requires logging in.  
Cancel  
After logged in, press [RETURN] on the remote control to display the  
logout dialog.  
For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 43)  
M
26_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The default administrator ID is “admin”, and the password must be set when the user log in at the first time.  
J
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or  
using the default wireless router password may expose your video data to potential threat.  
To prevent from your personal information being exposed, please change your password every 3 months.  
Note that the security and other related issues caused by careless management of password shall be be in the charge of the  
user.  
Locking All Buttons  
This will restrict access to all buttons available in the DVR.  
1. In Live mode, press buttons in the order of [STOP (@)]  
2014-01-01 01:10:25  
[FREEZE][STOP (@)][FREEZE][MENU].  
<All Key Lock> confirmation window appears.  
2. Select <OK>.  
All Key Lock  
Are you sure to all key lock?  
All keys are locked.  
OK  
Cancel  
3. In the lock condition, press any button to display a dialog  
where you are prompted to enter the password for  
unlocking the buttons.  
The button lock will be released if you enter the admin  
password.  
English _27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
LIVE SCREEN CONFIGURATION  
Icons on the Live Screen  
You can check the status or operation of the DVR with the icons on the live screen.  
a
d b  
c
d
2014-01-01 01:10:25  
CAM 01  
g f  
e
Part Names  
Functions  
Current Date, Time  
Login Information  
Displays the current time and date.  
a
b
When you are logged in, the “LOG ON” icon will be displayed.  
Displayed if the recording is in process.  
To cancel the recording, enter the password.  
Displayed if the zoom function is activated.  
Screen Mode  
c
Displayed if you press the Pause button.  
Displayed in Auto Sequence mode where all channels are switched at the specific time  
interval.  
Displayed if there is a problem with the cooling fan.  
Displayed if the HDD is full and the DVR has an insufficient space to record.  
Displayed if no HDD is installed or the existing HDD should be replaced.  
Displayed if the HDD needs a technical examination.  
System  
d
Operation  
Displayed while the backup is in process or if the backup data is played.  
Displayed if a new firmware is found from the network.  
28_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names  
Functions  
Displayed if no input is entered in the condition that the camera is set to <ON>.  
Nothing will be displayed on the screen if the camera is set to <OFF>.  
Displays the camera name and the changed channel, if any.  
Video Input  
e
f
Status  
Camera Name/ Channel  
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.  
Displays AUDIO ON/MUTE.  
Not displayed in video mode if deactivated.  
If the sensor is set to <ON>, the input signal will be displayed on the screen of the  
Camera  
connected channel.  
g
Operation  
Displayed if a motion detected in the condition that the motion detection is set to <ON>.  
Appears when the Tampering Detection is set to <ON> and a tampering attempt is  
detected.  
Displays the current record mode from Record/Event/Schedule.  
Error Information  
• If the internal HDD is not connected, the “NO HDD”(  
) message will appear; if there occurs a problem,  
you will see the “HDD FAIL”(  
) message in the top left corner. In this case, make sure you contact the  
service center for assistance as this may cause a failure of recording, playback or backup.  
• If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and  
the fan error icon (  
works.  
) will be displayed on the top left corner. In this case, check to see if the internal fan  
As a fan error can shorten the product life, make sure you contact the service center for assistance.  
If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.  
M
Live Screen Menu  
In addition to the buttons on the front panel or the remote control, you can access a desired menu by right-  
clicking the mouse any area in live mode.  
Right click opens the context menu which shows different menu items according to the situation, such as  
logged in/out state, split screen mode, and various operational conditions.  
Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.  
M
Scene Mode  
2014-01-01 01:10
2014-01-01 01:10:S2c5ene Mode  
Spot Out 1  
Spot Out 2  
Audio Off  
Freeze  
Spot Out 1  
Spot Out 2  
PTZ Control  
Zoom In  
Audio  
Stop Alarm  
Record  
Freeze  
Stop Alarm  
Record  
Play  
Search  
Play  
Backup  
Search  
Main Menu  
Shutdown  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Logout  
Hide Launcher  
Logout  
< Split Mode Menu >  
< Single Mode Menu >  
English _29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
Split Mode Menu  
The context sensitive menu in split mode differs, depending on the login/logout status.  
Scene Mode  
Spot Out 1  
Spot Out 2  
Audio Off  
Freeze  
2014-01-01 01:10:25  
a
b
c
d
Stop Alarm  
Record  
e
f
Play  
g
Search  
h
Backup  
i
Main Menu  
Shutdown  
Hide Launcher  
Logout  
j
k
l
m
Menu  
Scene Mode  
Spot Out1/2  
Audio On/Off  
Freeze  
Stop Alarm  
Record/Stop  
Play  
Search  
Backup  
Main Menu  
Shutdown  
Functions  
Refer to “Live Mode”. (Page 33)  
Refer to “Spot Out”. (Page 35)  
Refer to “Audio ON/OFF”. (Page 36)  
Refer to “Freeze”. (Page 36)  
a
b
c
d
e
f
g
h
i
j
k
l
m
Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 37)  
Starts/stops the standard recording.  
Plays the search result (data). Refer to “Search & Play > Play”. (Page 85)  
Refer to “Search & Play > Search”. (Page 82)  
Refer to “Main Menu > Setting the Backup”. (Page 64)  
Accesses the main menu. Refer to the Using the DVR section. (Page 38)  
Turns down the DVR.  
Show/Hide Launcher Shows or hides the launcher. Refer to “Show / Hide the Launcher Menu”. (Page 32)  
Login/Logout  
You can log in or out.  
30_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Single Mode Menu  
The single mode menu is available only in Single Mode.  
The menu, which appears as <Screen Mode> on a single screen, appears as <Full Screen> after selecting  
only one channel on a split screen.  
2014-01-01 01:10Scene Mode  
2014-01-01 01:10:25  
Full Screen  
Spot Out 1  
Spot Out 2  
PTZ Control  
Zoom In  
Audio  
a
Spot Out 1  
Spot Out 2  
PTZ Control  
Zoom In  
Audio  
b
c
Freeze  
Freeze  
Stop Alarm  
Record  
Stop Alarm  
Record  
Play  
Play  
Search  
Search  
Backup  
Backup  
Main Menu  
Shutdown  
Main Menu  
Shutdown  
Hide Launcher  
Logout  
Hide Launcher  
Logout  
< Single Mode Menu >  
< Menu after selecting one channel  
on the split screen >  
Menu  
Full Screen  
Functions  
Select and click a desired channel in Split mode to switch to the full screen of the selected  
a
channel.  
Accesses the PTZ Control menu.  
PTZ Control  
Zoom In  
b
c
The PTZ menu is activated only in One-Channel Live mode. (Page 79)  
Enlarges the selected image. (Page 36)  
English _31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
Show / Hide the Launcher Menu  
The Launcher menu appears on the bottom of the live screen.  
1. In Live mode, right-click to display the context menu and select <Show Launcher> or <Hide Launcher>.  
If selected <Hide Launcher>, the launcher menu disappears on the bottom of the live screen.  
2. If <Show Launcher> is selected, the launcher menu appears at the bottom of the screen.  
If you click the launcher menu using the mouse, it directly goes into the menu.  
If no input is entered for 10 seconds, the menu will disappear.  
The Launcher menu can be accessed only by using the mouse.  
SRD-876D does not support the 16-split screen mode.  
M
2014-01-01  
01:10:25  
2014-01-01  
01:10:25  
a
b
cd e f g h ij  
Menu  
Functions  
Displays the current time and date.  
Date/Time  
The indication of AM/PM is displayed if you set 12 hours for the time format in “System >  
a
b
Date/Time/Language > Time”. (Page 38)  
Press this button to switch the screen mode in sequence.  
The current mode is highlighted in white.  
Screen Mode  
Menu Expansion Button  
Audio  
Zoom  
Click to display the hidden menu to the right.  
c
d
e
Turns ON/OFF the sound of the selected channel.  
Enlarges the selected area. This is available only in Single Live mode.  
Runs the PTZ Control launcher.  
PTZ  
f
The PTZ control launcher will be active on the Live screen after you select a single channel.  
Alarm  
Freeze  
Play  
Stops the alarm if it's activated.  
g
h
i
j
Freezes the Live screen temporarily.  
Enters Play mode if a file to play exist, and if not, enters Search mode.  
Start/End recording the Live screen.  
Record  
32_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIVE MODE  
SRD-1656D/1676D display Live images from 16 channels in a total of 8 layout of split screens.  
Switching the screen mode  
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in  
the context menu.  
Press the [MODE] button on the front panel or the remote control to switch the mode in the sequence of the  
launcher menu items.  
SRD-876D does not support the 16-split screen mode.  
M
CH1  
CH5  
CH9  
CH13  
CH2  
CH3  
CH4  
CH1  
CH4  
CH7  
CH2  
CH5  
CH8  
CH3  
CH6  
CH9  
CH2  
CH3  
CH7  
CH6  
CH7  
CH8  
CH1  
CH3  
CH2  
CH1  
CH4  
CH10  
CH14  
CH11  
CH15  
CH12  
CH16  
CH4  
CH5  
CH6  
16-split mode  
9-split mode  
4-split mode  
7-split mode  
CH2  
CH6  
CH8  
CH10  
CH3  
CH4  
CH5  
CH7  
CH9  
CH13  
CH1  
CH4  
CH2  
CH5  
CH3  
CH6  
CH1  
CH2  
CH11  
CH12  
CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16  
CH1  
CH1  
13-split mode  
16(A)-split mode  
PIP  
Auto Sequence  
Switching the split mode  
SRD-1656D/1676D display 16 Live images in the sequence of Single, 4-split and 9-split modes.  
Auto Sequence  
16  
13-16  
9-12  
5-8  
CH1  
CH4  
CH7  
CH2  
CH5  
CH8  
CH3  
CH6  
CH9  
CH1  
CH3  
CH2  
10-16  
1-9  
CH1  
CH4  
1-4  
1
Single mode  
4-split mode  
9-split mode  
In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be conducted  
M
at the set interval. (Page 48)  
In a split mode, If you have set <Multi CH SEQ Time> in “Setting the Device > Monitor”, Auto Sequence will be  
conducted at the set interval. (Page 56)  
English _33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
Manual Switching  
Press the left/right button on the front panel or the remote control, or click the arrow <◄/►> key to move to  
the next split mode.  
• If pressing the right [►] button in 9-split mode :  
9-split (CH 1~9) mode 9-split (CH 10~16) mode Auto Sequence  
CH1  
CH4  
CH7  
CH2  
CH5  
CH8  
CH3  
CH6  
CH9  
CH10  
CH13  
CH16  
CH11  
CH14  
CH12  
CH15  
CH1  
CH4  
CH7  
CH2  
CH5  
CH8  
CH3  
CH6  
CH9  
ꢂ
ꢂ
10-16  
1-9  
• If pressing the right [►] button in 4-split mode :  
Channel (CH 1~4) Channel (CH 5~8) Channel (CH 9~12) Channel (CH 13~16) Auto Sequence  
CH1  
CH2  
CH5  
CH6  
CH9  
CH10  
CH13  
CH14  
ꢂ
ꢂ
ꢂ
CH3  
CH4  
CH7  
CH8  
CH11  
CH12  
CH15  
CH16  
13-16  
9-12  
5-8  
1-4  
CH1  
CH3  
CH2  
CH4  
Channel Setting  
You can display the channel in a desired area of a split screen.  
1. Place the cursor over the camera name of each channel to display the <▼> key to the right on the screen.  
2. Click a camera name to display a channel list where you can select a different channel.  
3. Select a desired channel and click it.  
The current channel will be switched to the selected one.  
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also  
change the channel position.  
Ex : if switching CH 1 to CH 7  
CH1  
CH2  
CH3  
CH4  
CH7  
CH5  
CH9  
CH13  
CH2  
CH3  
CH4  
CH5  
CH9  
CH13  
CH6  
CH7  
CH8  
CH6  
CH1  
CH8  
ꢂ
CH10  
CH14  
CH11  
CH15  
CH12  
CH16  
CH10  
CH14  
CH11  
CH15  
CH12  
CH16  
34_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching to Single Mode  
When in split mode, select and double-click a desired channel to switch to its Single mode.  
Press the number corresponding to a desired channel on the front panel or the remote control to switch to its  
Single mode.  
Refer to “Remote Control > Using the numeric buttons”. (Page 15)  
Ex : If double-clicking CH 3 or pressing the number “3” on the remote control or the front panel.  
CH1  
CH5  
CH9  
CH13  
CH2  
CH3  
CH4  
CH6  
CH7  
CH8  
ꢂ
CH10  
CH14  
CH11  
CH15  
CH12  
CH16  
CH3  
SPOT OUT  
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out port.  
Selecting a Spot Out mode  
If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you  
can select a output screen mode.  
1. In Live mode, right-click any area on the screen.  
Scene Mode  
Spot Out1  
Spot Out2  
Audio Off  
Freeze  
2014-01-01 01:10:25  
Auto Sequence  
The Live menu appears.  
CH1  
CH2  
CH3  
2. Click Spot Out.  
CH4  
Stop Alarm  
Record  
CH5  
The split screen appears according to the Spot Out source.  
(Page 57)  
CH6  
Play  
CH7  
Search  
CH8  
Backup  
CH9  
Spot Out 1: It supports auto sequence and single mode by default,  
and additionally supports 16-split, 9-split and 4-split modes if  
selected <Multi Spot> out.  
Main Menu  
Shutdown  
CH10  
CH11  
CH12  
CH13  
CH14  
CH15  
CH16  
Hide Launcher  
Logout  
Spot Out 2: It supports auto sequence and single mode.  
English _35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
live  
ZOOM  
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to enlarge  
it twice.  
1. Select <Zoom In> in the right-click menu.  
Press the [ZOOM] button on the front panel or the remote control, or simply click <  
> in the launcher  
menu. The zoom box appears.  
2. Use the direction keys, or drag and drop to specify an area to enlarge.  
3. Press the [ENTER] button, or double-click the selected area to enlarge it twice.  
In the enlarged image, use the direction buttons (ꢀꢁ◄ ►) on the remote control or the front panel to move the enlarged  
area.  
4. Press the [ZOOM] button on the front panel or the remote control to release the zoom.  
2014-01-01 001:10:25  
2014-01-01 01:10:25  
ꢂ
AUDIO ON/OFF  
You can turn the sound on/off corresponding to the channel in Live mode.  
AUDIO ON/OFF in Single mode  
Click the audio icon ( ) on the screen, or press the [AUDIO] button on the front panel or the remote control  
to turn it on/off.  
Only the channel where <Audio> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live mode that  
M
you can use to turn the sound on/off.  
FREEZE  
This is available only in Live mode, this pauses playing the Live image temporarily.  
1. Press the [FREEZE] button on the front panel or the remote control, or click <  
> in the launcher menu.  
The playback of the image is stopped temporarily.  
Sound continues to play during the pause.  
2. Press the [FREEZE] button again, or click <  
>.  
This will release the freeze.  
36_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EVENT MONITORING  
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss/Tampering) if it occurs.  
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 56)  
• If multiple events occur simultaneously, the screen will switch to a split mode.  
2~4 events : 4-split mode  
5~9 events : 9-split mode  
10~16 events : 16-split mode  
-
-
-
• If the second event occurs within the set time of <Event Display>, the first event will last until the second  
one is terminated. (Page 56)  
Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.  
Event occurrence  
5 seconds  
Stop alarm  
CH1  
Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first  
event occurred in CH 1.  
Event occurrence  
4 seconds  
9 seconds  
Stop alarm  
CH1  
CH2  
CH1  
Press the [ALARM] button to reset the alarm settings and to release the event mode.  
M
J
If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will be  
performed.  
This will also apply to the Spot Out monitor.  
In case of continuous events such as motion detection, switching to another split mode display may not immediate if  
concatenating events follow, even when you stopped alarm of the event.  
English _37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
You can setup the system properties, devices, and options for recording, event, backup  
and network.  
SYSTEM SETUP  
You can setup Date/Time/Language, Permission, System Properties and Log.  
Date/Time/Language  
You can check and setup the current Date/Time and time related properties, as well as the language used for  
the interface on the screen.  
Setting the Date/Time/Language  
Set the Date/Time/Language  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or on the front panel.  
If not logged in, it prompts with login window.  
Refer to “Login”. (Page 26)  
2. Use the left/right buttons (◄ ►) to select the <System>.  
Logout  
Return  
System property setup menu is selected.  
3. Use the up/down buttons (ꢀꢁ) to select <Date/Time/  
Language> and press the [ENTER] button.  
System  
Date/Time/Language  
4. Select <Date/Time/Language>.  
Permission Management  
System Management  
Log Information  
A dialog to setup Date, Time and Language.  
5. Use direction buttons (ꢀꢁ◄ ►) to select an item to set  
and make your changes.  
• Date : Sets the date that will appear on the screen.  
You can select the date format.  
Date/Time/Language  
Date/Time/Language  
Holiday  
• Time : Sets the time and its format that will appear on the  
screen.  
Date  
2014-01-01  
YYYY-MM-DD  
24 Hours  
Time  
08:14:24  
GMT  
Select either one from <24 Hours, 12 Hours (AM/PM)>.  
Time Zone  
Time Sync.  
DST  
Setup  
• Time Zone : Sets the time zone of your area based on the  
Greenwich Mean Time (GMT).  
Dec First (Sun) 0  
Dec First (Sun) 0  
Language  
English  
GMT (Greenwich Mean Time) is standard World Time and the basis  
OK  
Cancel  
of world time zone.  
• Time Sync. : You can set the DVR’s current time  
synchronized to a selected <Time Server> regularly if you select to use <Time Server>.  
In this case, <Date/Time/Language> setup does not allow time adjustment.  
38_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- Time Server : Enter an IP or URL address of the time server.  
Date/Time/Language  
- Last Sync Time : Displays the most recent synchronization  
time from the selected time server.  
Date/Time/Language  
Holiday  
Time Synchronization Setup
- Activate as Server : Set to <Use> to allow the DVR to act  
Synchronization  
Time Server  
Last Sync Time  
Activate as Server  
Use  
203.248.240.103  
as a Time Server for other DVRs.  
Fail  
Use  
• DST : Set up Daylight Saving Time with its period to make  
the time earlier than the GMT of its time zone by 1 hour  
during the set period.  
OK  
OK  
Cancel  
Cancel  
Language  
English  
• Language : Select your language. Sets the language for the  
interface.  
English, French, German, Spanish, Italian, Chinese(Simplified),  
Russian, Korean, Polish, Japanese, Dutch, Portuguese, Turkish, Czech, Danish, Swedish, Thai, Romanian,  
Serbian, Croatian, Hungarian, Greek, Chinese (Traditional), Finnish and Norwegian are available.  
6. When the Date/Time/Language setup is done, press <OK>.  
You can also use numeric buttons on the remote control or front panel to enter values for Date, Time and other numeric  
M
fields.  
Setting Holiday  
You can set specific dates to Holidays according to your preferences.  
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Date/Time/Language> window to select <Date/Time/Language>, and  
press the [ENTER] button.  
2. Select <Holiday>.  
Date/Time/Language  
A calendar for Holiday setup appears.  
Holiday  
Date/Time/Language  
3. Use the left/right <  
> buttons to select year or month,  
2014  
Sun Mon Tue  
Jan  
and press the [ENTER] button.  
Wed Thu  
Fri  
3
Sat  
4
1
2
5
6
7
8
9
10  
17  
24  
31  
11  
18  
25  
12  
19  
26  
13  
20  
27  
14  
21  
28  
15  
22  
29  
16  
23  
30  
OK  
Cancel  
4. Use direction buttons (ꢀꢁ◄ ►) to select a desired date,  
and press the [ENTER] button.  
Date/Time/Language  
Holiday  
Date/Time/Language  
You will see the “Setting Holiday” screen.  
2014  
Jan  
Setting Holiday  
Ex : Select January 13th and check on <1/13> only to make every  
January 13th a holiday. Check both on <1/13> and <Jan 2nd  
Mon> to make every January 13th and 2nd Monday of January  
holidays.  
1 / 13  
31  
Jan 2nd Mon  
26  
27  
OK  
Cancel  
28  
29  
30  
5. When the Holiday setup is done, press <OK>.  
OK  
Cancel  
Using the Calendar  
Using the mouse may help make setup easier.  
x
Select year and month.  
Select the left/right <  
by 1 year/month.  
> key on the left/right side of year/month and press [ENTER] button to adjust  
Use direction buttons to select a date and press [ENTER] button.  
y
A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event Search.  
English _39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Permission Management  
You can set permissions of each user over the DVR's specific function and settings.  
Setting the Administrator  
You can set and change Administrator’s ID and password.  
The administrator can use and set all menu items and functions.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
Permission Management  
move to <Permission Management>, and press  
Admin  
Group  
User  
Setup  
[ENTER] button.  
ID  
admin  
New Password  
************  
************  
2. Select <Admin>.  
Confirm P/W  
A dialog for Admin ID and Password input appears.  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and set the ID and password.  
OK  
Cancel  
The default administrator ID is “admin”, and the password must  
M
be set when the user log in at the first time.  
To prevent from your personal information being exposed, please change your password every 3 months.  
Note that the security and other related issues caused by careless management of password shall be be in the charge of the  
user.  
4. When the administrator setup is done, press <OK>.  
Using Virtual Keyboard  
x
y
z
For alphanumeric inputs, the virtual keyboard window  
appears.  
`
1
w
s
2
e
d
c
3
r
4
t
5
6
u
j
7
i
8
o
l
9
p
;
0
[
-
]
=
\
Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
q
a
z
y
h
Del  
character, and press the [ENTER] button.  
f
g
b
k
,
‘
Caps Lock  
Shift  
x
v
n
m
.
/
In the upper text input box of the virtual keyboard, there  
displays a list of candidate words containing the selected  
character.  
Space  
Ctrl  
OK  
Cancel  
{
|
Select a word from the list, or use the keyboard to enter the whole word.  
If there are many of candidate words, use <  
,
> buttons to move between them forward and backward.  
Select <OK>.  
Entered word is applied.  
For upper case letters, use <Caps Lock> button.  
For special characters, use <Shift> button.  
Using the virtual keyboard is the same to a normal keyboard use in your region.  
You can enter the ID with case-insensitive alphanumeric characters only.  
For the password, use alphabets and special characters excluding < > and <">.  
\
You can use number buttons on the remote control or front panel.  
40_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Group  
You can create user groups and setup permissions for those user groups.  
You can register a user for each group in <User>.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
Permission Management  
move to <Permission Management>, and press  
Group  
Admin  
User  
Setup  
[ENTER] button.  
Group  
Add  
Delete  
Rename  
Group Authority  
Live View  
2. Select <Group>.  
Setup  
Setup  
Setup  
Setup  
Search  
A window for <Add>, <Delete>, <Rename>, and  
<Group Authority> setup appears.  
Backup  
Menu  
Bi-directional audio  
Record Lock  
PTZ  
Remote Alarm Out  
Shutdown  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and set the value.  
OK  
Cancel  
• Add, Delete, Rename : You can add, delete, rename a  
group or modify the permissions given to the group.  
The virtual keyboard appears when <Add> or <Rename> was selected.  
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already  
been deactivated. Select <Add> to display the virtual keyboard. Enter a group name. You can add up to  
10 groups.  
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts  
belonging to that group.  
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.  
For entering a group name, refer to “Using Virtual Keyboard”. (Page 40)  
• Group Authority : Sets permissions to access menu items of each group.  
Users of a group can access checked functions.  
4. When the group setup is done, press <OK>.  
To set the group authority  
You can set the permissions of the group users to access the menu according to the channel.  
1. Select a menu to which the group permission is assigned.  
Permission Management  
The menu where the group permission is assigned will be  
Group  
Admin  
User  
Setup  
displayed in the Live menu when a group user logs in.  
Group  
ABC  
Add  
Delete  
Rename  
Group
Channel Setup  
• Live View : You can set the permission to access the Live  
screen according to the channel.  
Live V
Searc
Backu
Menu  
All  
1
5
9
2
3
7
4
8
6
10  
14  
11  
15  
12  
16  
• Search : You can set the permission to access the Search  
menu according to the channel.  
Bi-dir13
Reco
Cancel  
n  
OK  
• Backup : You can set the permission to access the Backup  
menu according to the channel.  
OK  
Cancel  
• Menu : You can set menus accessible with a specific  
permission.  
Permission Management  
Menu Permission  
Group users can access the permitted menus only.  
Select a menu to display the Menu Permission screen.  
All  
System  
Device  
Record  
Event  
Backup  
Network  
• Bi-directional audio: You will be given permission to use  
two-way audio features.  
Date/Time/Language  
Date/Time/Language  
Holiday  
System Management  
• Record Lock, PTZ, Remote Alarm Out, Shutdown : Select  
System Information  
Log Information  
an item so that the item will be added to the permissions.  
System Log  
Event Log Backup Log  
2. Select <OK>.  
Select and assign a group user so that the user can  
access the specified menu.  
OK  
Cancel  
English _41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
To restrict the user permissions  
If the admin restricts all permissions of an added group, the users belonging to that group can access only  
the default minimum menus and can change the user’s own password only.  
1. Start the DVR.  
If all permissions are restricted, only the Login dialog  
should appear.  
2. Log in with a registered user ID.  
Login  
ID  
abc  
Password  
OK  
Cancel  
3. Right-click any area on the screen.  
If all permissions are restricted, only the accessible context  
menus should appear.  
2014-01-01 01:10:25  
Scene Mode  
Audio Off  
Freeze  
Stop Alarm  
Record  
User Menu  
Hide Launcher  
Logout  
2014-01-01  
01:10:25  
To change the user password  
If you log in with a user account that is restricted to access the menu, you can change your own password only.  
1. Log in with your account.  
Permission Management  
User  
2. Select <User Menu>.  
The Permission Management setup screen appears.  
ID  
USER  
New Password  
Confirm P/W  
************  
************  
3. Select <Permission Management>.  
The Password setup dialog appears.  
4. Enter a new password.  
5. Select <OK>.  
OK  
Cancel  
You change to the password will be applied.  
42_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the User  
You can add a user and edit information of a registered user.  
Users can be added only if a group was created in <Group> menu.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <Permission Management>, and press  
[ENTER] button.  
Permission Management  
User  
Admin  
Group  
Group  
Group  
All Group  
Name  
Setup  
Add  
Delete  
ID  
Viewer  
2. Select <User>.  
A window for Add User appears.  
3. Use direction buttons (ꢀꢁ◄ ►) to select <Add> from the  
window.  
Previous/Next Page  
A window for “Add User” appears.  
OK  
Cancel  
4. You can configure the Network Viewer settings including  
name, ID, viewer, Select Group and password.  
Result of the user setup appears in the <User> window.  
To change the user property, use “Edit User”.  
Permission Management  
User  
Admin  
Group  
GrouName  
Group  
Setup  
The “Edit User” window appears when you select a  
desired item to be changed in the <User> window.  
AddUser  
Add  
Delete  
ID  
• Viewer : If you select <Use>, you will be given access to the  
Viewer  
Not Used  
ABC  
Web Viewer and Network Viewer.  
Select Group  
Password  
Confirm P/W  
Refer to “Connecting Web Viewer”. (Page 88)  
OK  
Cancel  
For more information about use of Network Viewer, refer to the  
Network Viewer's user guide.  
Previous/Next Page  
OK  
Cancel  
5. When the user setup is done, press <OK>.  
Setting Permissions  
You can set restricted access for all general users.  
Items with restrictions will require logging in for use.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <Permission Management>, and press  
[ENTER] button.  
Permission Management  
Setup  
Admin  
Group  
User  
Restricted Access  
Live View  
Backup  
Remote Alarm Out  
Record Lock  
Shutdown  
Search  
All  
PTZ  
2. Select <Setup>.  
The Restricted Access, Restriction on Network Access,  
Restriction on Network Access  
All Network  
Web Viewer  
Auto Log out, Manual Input of ID setup screen appear.  
Auto Log out  
OFF  
ON  
Manual Input of ID  
Touch Button Sound  
Touch Button  
OFF  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
ON  
ON  
OFF  
OFF  
and set the value.  
OK  
Cancel  
• Restricted Access : All menu items allowed for a user can  
be set with restricted access.  
- Checked ( ) : Restricted  
- Not checked ( ) : Accessible  
If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>  
setting.  
If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group  
Authority> setting.  
• Restriction on Network Access : Restricts remote access from a <Restricted Access> network.  
- All Network : Restricts all access instances via Network Viewer and Web Viewer.  
- Web Viewer : Restricts access via the Web Viewer.  
• Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of  
time.  
English _43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
• Manual Input of ID : Prompts you to enter the user ID  
manually for the login process.  
- Checked ( ) : Encloses the registered user IDs with the  
[ ] symbols.  
Login  
ID  
Use the virtual keyboard to enter the user ID.  
*****  
Password  
• Touch Button Sound : You can set whether to sound beep  
on use of front touch buttons.  
OK  
Cancel  
• Touch Button : You can set whether to use the front touch  
buttons or not.  
4. When the permission setup is done, press <OK>.  
System Management  
You can check the system version, update to a newer version, as well as data backup and initialization.  
Checking the System Information  
You can check the current system version, broadcasting system, MAC address. You can update the system.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
System Management  
move to <System Management>, and press [ENTER]  
System Information  
Settings  
button.  
System Information  
Software Version  
v1.0xh_yymmddhhmmss  
Broadcast Format  
NTSC  
2. Check the Software Version, Broadcast Format and MAC  
MAC Address  
00:00:F0:54:FF:FF  
Address.  
S/W Upgrade  
Search  
OK  
Device  
Network  
• System Information : Shows the current system’s  
information.  
Version  
No S/W Data  
DVR Name  
DVR  
The values can not be changed by a user.  
Previous  
• S/W Upgrade : Updates the DVR’s software up to date.  
• DVR Name : Assigned name will be displayed in Network  
Viewer, when connected to the DVR.  
44_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Updating the Software  
1. Connect a device storing the software to be updated. (It may take about 30 seconds to recognize the  
device.)  
Upgradeable devices include USB memory, CD/DVD and network device.  
To update the network, the current DVR should have been connected to the network.  
Upgrade via the proxy server may not be enabled due to the restricted access.  
2. Select <System Management> from <System> window.  
3. Select <System Information>.  
4. Press <Search> button to display updated image, then the <Search> button switches to <Upgrade>.  
The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is same to  
or older than that of <S/W Upgrade>.  
5. Press <Upgrade> button to display confirmation popup  
for upgrading.  
System Management  
System Information  
Settings  
Press <OK> in the “System Upgrade” window.  
System Information  
Software Version  
v1.0xh_yymmddhhmmss  
System Upgrade  
Broa
While updating, it shows the progress.  
MAC
Current Version  
v1.0xh_yymmddhhmmss  
New Version  
S/W
v1.0xh_yymmddhhmmss  
Do you want to upgrade?  
OK  
Devic
OK  
Cancel  
Versi
DVR Name  
DVR  
Previous  
System Management  
System Information  
Settings  
System Information  
Software Version  
v1.0xh_yymmddhhmmss  
BroadcaS/WUpgrade
MAC Ad
Software upgrading...  
S/W U
OK  
Device  
Version  
DVR Name  
DVR  
Previous  
6. When the updating is done, it automatically restarts.  
Do not turn the power off until it finishes restarting.  
If “Upgrade Failed” appears, retry from the step 4.  
When you experience continued failure, consult the service  
center for assistance.  
When you perform S/W update remotely using Smart Viewer,  
it may take a max of 3 minutes to complete the update since  
Smart Viewer popped up a confirmation message. This is to  
guarantee that the DVR set operates stably. For a faster update,  
use the USB cable to connect to the DVR set.  
M
English _45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Settings  
You can copy and import the DVR settings by using a storage media.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <System Management>, and press [ENTER]  
button.  
System Management  
Settings  
System Information  
Storage Device  
0 MB (Remained Capacity)  
Export  
Import  
DVRUSB  
38010100  
No data  
2. Select <Settings>.  
USBDVR  
Include Network Settings  
A window of storage device and load factory default  
appears.  
Load Factory Default  
Default  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and export or import settings data to a storage device.  
Previous  
• Storage Device : Shows the connected storage device.  
• Export : All logs recorded in the DVR are exported to the  
storage media.  
• Import : Imports DVR settings from the storage device and applies to the DVR.  
If <Include Network Settings> is checked, the network settings will be imported too.  
After importing the configuration, please reboot DVR to take effect.  
• Load Factory Default : If <Default> is selected, a  
confirmation dialog for “Load Factory Default” prompts.  
Press <OK> to initialize the system to the factory default.  
System Management  
Settings  
System Information  
Storage Device  
0 MB (Remained Capacity)  
Load Factory Default  
DVR
DVR will restart after loading facotry default.  
USB
Sure to Default Setting?  
Recording stops few second.  
4. To move to the previous menu, press <Previous>.  
OK  
Cancel  
Load
Previous  
Log Information  
You can browse logs on the system and events.  
System Log  
System Log shows log and timestamp on every system start up, system shutdown, and changes on system  
settings.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
Log Information  
move to <Log Information>, and press [ENTER] button.  
System Log  
Event Log  
Backup Log  
Search  
Search Day  
First Page  
2014-01-01  
Last Page  
2. Select <System Log>.  
Type View all  
No.  
Log List  
Date/Time  
Refer to “Using the Calendar”. (Page 39)  
Click on the calendar < > to display the calendar window.  
• Type : When there are too many logs, you can display logs  
of the desired format by selecting the type.  
Previous/Next Page  
• Export : All logs recorded in the DVR are exported to the  
Export  
Previous  
storage media.  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item, and press <Search>.  
46_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Event Log  
Event log shows recorded events on alarms, motion detections and video loss.  
It also shows the log and its timestamp.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
Log Information  
move to <Log Information>, and press [ENTER] button.  
Event Log  
System Log  
Backup Log  
Search Day  
First Page  
2014-01-01  
Last Page  
Search  
All CHs  
2. Select <Event Log>.  
CH  
Type  
Date/Time  
View all  
No.  
Log List  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
7
6
5
4
3
2
1
Motion Detection [CH 7]  
Motion Detection [CH 6]  
Motion Detection [CH 5]  
Motion Detection [CH 4]  
Motion Detection [CH 3]  
Motion Detection [CH 2]  
Motion Detection [CH 1]  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
2014-01-01 00:02:18  
and select it.  
4. Set Search Day, Channel and Type and the press  
<Search>.  
Previous/Next Page  
Refer to “Using the Calendar”. (Page 39)  
Export  
Previous  
Click on the calendar < > to display the calendar window.  
Backup Log  
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <System> window to  
Log Information  
move to <Log Information>, and press [ENTER] button.  
Backup Log  
System Log  
Event Log  
Search Day  
First Page  
2014-01-01  
Last Page  
~
2014-01-02  
Search  
2. Select <Backup Log>.  
Previous/Next Page  
No.  
User  
Date/Time  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and select it.  
4. Specify a search term and select <Search> in the right  
corner.  
Backup details for the search term will be listed.  
Export  
Previous  
English _47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
SETTING THE DEVICE  
You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.  
Camera  
Setting the Camera  
You can set Video, Audio, Channel Name and Dwell Time of a Camera.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Return  
panel.  
2. Use the left/right button (◄ ►) to select <Device>.  
Device setting menu is selected.  
Device  
3. Use the up/down buttons (ꢀꢁ) to move to <Camera>,  
Camera  
and press [ENTER] button.  
Storage Device  
Remote Device  
POS Device  
Monitor  
4. Select <Camera>.  
Camera  
Camera  
Displays settings window for Video, Audio, CH Name,  
SEQ-Dwell Time, Progressive, Screen Setup and Privacy  
Region.  
PTZ  
CH  
1
Video   
Audio  
CH Name  
SEQ-Dwell Time  Progressive   
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  CAM 01  
OFF  CAM 02  
OFF  CAM 03  
OFF  CAM 04  
OFF  CAM 05  
OFF  CAM 06  
OFF  CAM 07  
OFF  CAM 08  
5 sec  
5 sec  
5 sec  
5 sec  
5 sec  
5 sec  
5 sec  
5 sec  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
2
3
4
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
5
6
and set the value.  
7
8
• Video  
Previous/Next Page  
Screen Setup  
Privacy Region  
OK  
- <ON/OFF> : You can turn ON/OFF the selected channel’s  
Cancel  
camera.  
- <Covert1> : Shows information other than the video of  
the selected channel.  
For privacy protection, it does not display the video while the recording continues.  
- <Covert2> : Shows nothing but an empty screen while the recording continues.  
If the channel is set to <Covert1> or <Covert2> mode, the channel’s sound is not hearable.  
M
However, the channel’s sound is recorded if its Audio setting is set to <ON>, even the sound is not heard in Live mode.  
• Audio  
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.  
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.  
Audio output is available for only 1 channel.  
• CH Name : Up to 15 characters including blanks are allowed.  
Refer to “Using Virtual Keyboard”. (Page 40)  
The first character should not be empty.  
48_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.  
If set to <OFF>, the channel is not listed in the Auto Sequence mode.  
• Progressive : You can turn on/off progressive camera settings.  
If you use a progressive camera, you can set it to <On> to eliminate screen shaking.  
J
• Screen Setup : The video appeared on the screen may vary  
depending on the channel’s camera, configure the DVR  
display to your preferences.  
Select a channel and adjust the  
<
(Brightness)>,  
<
(Contrast)>, and  
<
(Color)> of the selected channel.  
Press the <Init> to initialize settings back to the default.  
Screen Setup  
You cannot adjust Brightness, Contrast or Color for HD-SDI  
CH1  
42  
53  
50  
Init  
Apply to All CH  
Channel.  
OK  
Cancel  
• Privacy Region : You can specify a certain area of the  
camera video to be protected for your privacy.  
• HD/SD Switch: You may setup the numbers of HD channel based on your needs, after completing setup,  
please click OK on HD/SD Switch menu, and DVR would restart to take effect.(HD/SD Switch is available  
for SRD-1680D only.)  
6. When the camera setup is done, press <OK>.  
To set the privacy zone  
x
y
Select <Privacy Region>.  
When “Privacy Region” window appears, select a  
channel for detection and set the area of motion  
detection.  
• To set the area in “Privacy Region” window  
In the “Privacy Region” window, select desired region  
Privacy Region  
CH1  
from <  
>.  
Privacy Region1  
Individual  
Cancel  
Apply to All CH  
• Privacy Region  
OK  
You can specify up to 4 privacy zones for each channel,  
which can be identified by the color.  
1
Purple 2 Green 3 Blue 4  
Yellow  
• To set the area using <Individual> selection  
In the “Privacy Region” window, you can select cells individually by using <Individual>.  
When selected <Individual>, “Privacy Region” window disappears and you can select cells one by one.  
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]  
button on the remote control to display the “Privacy Region” window again.  
- Clear All : Selected cell is removed from the Privacy Region.  
Clear All  
- Menu : After selecting individual motion areas, move to the “Privacy Region” window.  
Menu  
If selected <Apply to All CH>, selected motion area is applied to all channels.  
z
When completing the privacy zone settings, click <OK>.  
English _49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Setting the PTZ  
To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.  
For other settings, refer to the <Remote Device> settings. (Page 54)  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Camera  
move to <Camera>, and press [ENTER] button.  
PTZ  
Camera  
CH  
1
Port   
RS-485  
RS-485  
RS-485  
RS-485  
RS-485  
RS-485  
RS-485  
RS-485  
ID  
0
1
2
3
4
5
6
7
Protocol  
None  
None  
None  
None  
None  
None  
None  
None  
2. Select <PTZ>.  
>
>
>
>
>
>
>
>
2
A window of PTZ settings appears.  
3
4
5
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
6
7
and select it.  
8
Previous/Next Page  
• Port : Select a port control method for the camera that is  
connected to a channel.  
OK  
Cancel  
You have two choices : <RS-485> and <Coaxial>.  
• ID : Set the ID of the connected camera of each channel.  
You can easily setup by using the numeric buttons on the remote control or front panel.  
• Protocol : Set the protocol of the connected camera of each channel.  
You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.  
For the <Coaxial> type, CCVC and PELCO-C protocols are supported.  
M
<Coaxial> type is available for SRD-876D/1656D/1676D channel.  
4. When the PTZ setup is done, press <OK>.  
50_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Storage Device  
You can check information on storage devices.  
Confirming Devices  
You can check storage devices and their free space, usage as well as status.  
Devices available are HDD, and USB devices (Memory, HDD, CD/DVD).  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
Device  
Format  
HDD Alarm  
Device  
No.  
Used/Total  
Usage  
Status/Management  
2. Select <Device>.  
HDD  
1
–
3.92G/0.98T  
0 / 0  
Internal  
Backup  
Normal  
-
CD/DVD  
• No. : Shows the assigned number of the internal HDD.  
To see the detailed positioning of the HDD according to the  
number, refer to <HDD Map>.  
• Used/Total : Shows the used/total capacity of the storage  
device.  
HDD Map  
OK  
Cancel  
• Usage : Sets the storage device’s usage.  
- USB memory is used only for backups.  
External USB HDD, SATA HDD are used for extension and backup.  
A maximum of 2TB for each port is supported for backup on a high capacity SATA HDD such as RAID equipment  
(ex: SVS-5R), and a maximum of 4TB for extension purposes.  
SVS-5R supports only RAID1 and RAID5.  
If an eSATA HDD device is used for extended storage or backup purposes, disconnecting eSATA device may restart the  
system.  
For backup use, the device can be disconnected if it’s not in use.  
• Status/Management : Shows the current status of the HDD, as in Normal/Check/Replace.  
- Normal : Available to use  
- Check : Available to use but recommended to replace  
- Replace : Requires immediate replacement.  
• HDD Map : Shows the internal HDD’s locations according to  
HDD Map  
assigned numbers.  
Refer to this for servicing or additional HDD installation.  
3. To move to the previous menu, press <OK>.  
ꢃ
ꢁ
ꢀ
ꢂ
OK  
English _51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Formatting  
You can format a storage device.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
Format  
Device  
HDD Alarm  
Device  
Select  
Used/Total  
Usage  
2. Select <Format>.  
HDD  
1
–
3.92G/0.98T  
0 / 0  
Internal  
Backup  
CD / DVD  
A window for selection of device for formatting appears.  
3. Use direction buttons (ꢀꢁ◄ ►) to select a device to be  
formatted.  
Format  
OK  
Cancel  
4. Select <Format> on the bottom of the screen.  
Press <OK> on the “Manage” confirmation window will  
start formatting the selected device.  
5. When the formatting is done, press <OK>.  
Storage Device  
Format  
Device  
HDD Alarm  
Device  
HDD  
Select  
Used/Total  
Usage  
1
3.92G/0.98T  
Internal  
CD / DManage  
Formatting deletes all recordings.  
Proceed formatting?  
Recording stops few second.  
OK  
Cancel  
Format  
OK  
Cancel  
52_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDD Alarm  
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,  
and its duration.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
HDD Alarm  
Device  
Format  
2. Select <HDD Alarm>.  
Check Alarm Output Port  
1
4
2
3
BEEP  
All  
A window for setting HDD check and replace output ports  
Duration  
OFF  
and their durations appears.  
Replace Alarm Output Port  
1
4
2
3
BEEP  
All  
3. Use direction buttons (ꢀꢁ◄ ►) to move to the desired  
Duration  
OFF  
item.  
• Alarm  
OK  
Cancel  
- Alarm signal will output through the alarm out port on the  
rear side when selected <1>, <2>, <3>, and <4>.  
- If <BEEP> was selected, a beep will sound.  
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.  
• Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm  
output port.  
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified  
alarm output port.  
• Duration : Sets the alarm duration for the alarm signal and beep sound.  
- Check Alarm, Replace Alarm signals will output through the selected alarm out ports (1, 2, 3, and 4).  
- If <BEEP> was selected, a beep will sound.  
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.  
<Check> status means that the HDD is operating but it has problems that require technical examination.  
M
(
) appears on the Live screen.  
<Replace> status means that the HDD has defect and requires immediate replacement.  
(
) appears on the Live screen.  
If the installed HDD is not recognized properly, a confirmation popup will appear.  
4. When the HDD Alarm setup is done, press <OK>.  
English _53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Remote Devices  
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Remote Device  
move to <Remote Device>, and press [ENTER] button.  
Baudrate  
9600  
Parity  
None  
Data  
8
Stop Bit  
1
Transfer type  
Half Duplex  
  
  
  
2. Use direction buttons (ꢀꢁ◄ ►) to move to the desired  
item, and press [ENTER] button.  
System Keyboard  
Remote Control  
OFF  
ON  
ID  
ID  
1
0
3. Set the values of each communication setup of the remote  
device.  
• Baudrate : Baud rate settings of the DVR, PTZ camera and  
system keyboard should be matched for proper operations.  
OK  
Cancel  
4. Make sure to match IDs of the DVR, System Keyboard  
and Remote Control, and press <OK>.  
For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 15)  
M
POS Devices  
You can set properties of POS devices connected to the DVR.  
A POS device connection requires channel, preset, and Port/Ethernet settings.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
POS Device  
move to <POS Device>, and press [ENTER] button.  
POS USE  
POS Device Setup  
POS  
CH  
Preset   
No preset  
No preset  
No preset  
No preset  
No preset  
No preset  
No preset  
No preset  
Port/Ethernet  
None  
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
1
2
3
4
5
6
7
8
None  
None  
None  
None  
None  
None  
None  
None  
None  
and set the value.  
None  
None  
• POS USE : When selected <POS USE>, DVR and POS will  
None  
None  
be connected.  
None  
None  
Previous/Next Page  
If you change settings for the device and press <OK> while the  
<POS USE> is not checked, the changes for POS device will not  
be saved.  
J
OK  
Cancel  
54_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• POS Device Setup : Sets the communication setups for the  
POS device and DVR.  
POS Device  
POS USE  
POS Device Setup  
Port/Ethernet  
POS  
CH  
Preset   
No preset  
It is independent to the Remote Device setup.  
1
2
3
4
5
6
7
8
None  
None  
POS Device Setup  
Stop bit  
1   
Baudrate  
Parity  
Data  
7
1200  
None  
No
None  
No
None  
OK  
Cancel  
Nret  
No preset  
Previous/Next Page  
OK  
Cancel  
• CH : Select the camera to be synchronized to the POS  
device.  
POS Device  
POS USE  
POS Device Setup  
Port/Ethernet  
If selected a channel input field, “Sync Channel Setup” window  
POS  
CH  
Preset   
No preset  
1
2
3
4
5
6
7
8
None  
None  
Sync Channel Setup  
appears.  
1
9
2
3
4
5
6
7
8
CH  
One POS device can be synchronized to up to 16 cameras  
(channels), however one channel cannot be synchronized to  
multiple POS devices.  
10  
11  
12  
13  
14  
15  
16  
None  
None  
OK Cancel  
No preset  
Previous/Next Page  
Channels to be synchronized to a POS device should be set to  
“Event” in “Main Menu > Record > Recording Schedule”.  
(Page 58)  
OK  
Cancel  
• Preset : Sets the name, start and end strings of the receipt  
POS Device  
for the preset.  
Preset Setup  
Preset name should be unique.  
Add  
Del  
Add Preset  
No.  
Use <Add> button to display “Add Preset” window, and set its  
Name  
Start Keyword  
name, start string, and end string.  
End Keyword  
OK  
Cancel  
Cancel  
• Port/Ethernet : Sets the port number for the DVR and POS  
device connection.  
OK  
OK  
COM1 : For RS-232C connections  
7001~7016 : For Ethernet connections  
Cancel  
3. When the POS Device setup is done, press <OK>.  
English _55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Monitor  
You can configure information to be displayed and its format for Spot Out monitor.  
Setting the Monitor  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Monitor  
move to <Monitor>, and press [ENTER] button.  
Monitor  
Spot Out  
Mode  
Event Display  
OFF  
Date  
2. Select <Monitor>.  
Display  
Time  
ON  
CH Name  
Icon  
Multi CH SEQ Time 5 sec  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
VGA/HDMI  
1280X1024  
and set the value.  
HDMI Resolution Auto Detection  
Screen mode  
Clear screen  
Level3 (High)  
• Event Display : Sets the dwell time of the event channel  
display on the monitor when an event occurs.  
If selected <Continuous>, it displays the channel until you  
press [ALARM] button to release it.  
Sharpness  
Display Position Setup  
OK  
Cancel  
• Display : Displays only checked items on the monitor screen.  
• Multi CH SEQ Time : Sets the interval between automatic display switching in 4-split and 9-split mode of  
the Live screen.  
• VGA/HDMI : Set your preferred screen resolution to <VGA> or <HDMI>.  
• HDMI Resolution Auto Detection : If you set it to <ON>, then the HDMI screen resolution is automatically  
detected.  
If a HDMI monitor is not connected, the resolution is set to VGA/HDMI.  
If <VGA> or <HDMI> is not supported by the monitor, it may not be able to display anything.  
• Screen mode : Set screen mode.  
• Sharpness : Set the clarity for the video screen.  
4. When the monitor setup is done, press <OK>.  
Screen Setup  
Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,  
depending on the condition. Then, you can change the display position of the data.  
1. In the <Device> window, press the up/down (ꢀꢁ) button to move to <Monitor> and press the [ENTER]  
button.  
2. Select the <Monitor> item.  
3. Select <Display Position Setup> in the bottom.  
2014-01-01 01:10:25  
You will move to the <Display Position Setup> window.  
4. Use the four direction buttons or the number buttons on  
Display Position Setup  
the front panel or the remote control to adjust the data  
30  
position.  
30  
30  
30  
OK  
Cancel  
56_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Spot Out  
You can set the DVR to output information / video apart from the monitor out.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Monitor  
Spot Out  
Monitor  
Mode  
move to <Monitor>, and press [ENTER] button.  
Spot Out 1  
Multi Spot  
SEQ  
2. Select <Spot Out>.  
Set Mode  
Set Mode  
All  
All  
Spot Out 2  
SEQ  
The number of Spot Out terminals differs according to the model.  
Event Display  
OFF  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and set the value.  
OK  
Cancel  
• Spot Out 1 : It supports auto sequence and single mode by  
default, and additionally supports 16-split, 9-split and 4-split  
modes if selected <Multi Spot> out.  
Monitor  
Spot Out  
Monitor  
Mode  
Spot Set Spot Out  
• Spot Out 2 : It supports auto sequence and single mode.  
Spot
1
2
3
4
5
6
7
8
• Set Mode : A window for “Set Spot Out” appears and you  
9
10  
14  
11  
15  
12  
16  
13  
can set the channel for it.  
Event
OK  
You can set the dwell time between the screen switching in  
“Setting the Device > Camera > SEQ-Dwell Time”.  
(Page 49)  
OK  
Cancel  
• Event Display : Sets the duration for the Spot Out on an  
event.  
If selected <OFF>, an event will not output to the Spot Out.  
You can setup using the mouse right button in Live screen.  
M
Refer to “Spot Out”. (Page 35)  
If selected <Multi Spot> double frame function is deactivated.  
4. When the Spot Out is done, press <OK>.  
Setting the Screen Mode  
You can configure the Live screen and Split Screens.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Monitor  
move to <Monitor>, and press [ENTER] button.  
Mode  
Monitor  
Spot Out  
2. Select <Mode>.  
Live Screen  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Play Screen  
and set the value.  
• Live Screen : Select split modes for the Live screen.  
16-, 9-, and 4-split screens are included by default.  
Live  
Play  
• Play Screen : Select split modes for the playback screen.  
Only the 13-split screen is optional.  
OK  
Cancel  
Black shows the playback while white shows the Live  
screen.  
4. When the screen mode setup is done, press <OK>.  
English _57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
SETTING THE RECORDING  
You can setup scheduled recording, event recording and other recording related settings.  
Recording Schedule  
Make your reservation on a date and time to schedule the recording on specified time.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Return  
panel.  
2. Use the left/right button (◄ ►) to select <Record>.  
Record menu is selected.  
Record  
3. Use the up/down buttons (ꢀꢁ) to move to <Recording  
Recording Schedule  
Event Record Duration  
REC Quality & Resolution  
Record Option  
Schedule>, and press [ENTER] button.  
4. Select <Recording Schedule>.  
Recording Schedule  
A window of scheduled recording setup appears.  
CH1  
All  
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Sun  
Mon  
Tue  
Wed  
Thu  
Fri  
and set the value.  
• Channel : Select a channel to set the recording schedule  
time and date format.  
Sat  
Hol  
Apply to All CH  
No Recording  
Event  
Continuous  
• Recording type : Select each time cell, and then select a  
type to start recording.  
Both(Cont&Evnt)  
OK  
Cancel  
• Apply to All CH : If selected <Apply to All CH>, “Apply to  
All CH” window appears.  
Recording Schedule  
CH1  
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23  
Press <OK> to apply the setup to all channels.  
All  
Sun  
Mon  
Tue  
Wed  
Thu  
Fri  
Apply to All CH  
6. When the recording schedule setup is done, press <OK>.  
Apply recording schedule to all channels?  
Event recording and scheduled recording starts about 3 seconds  
OK  
Cancel  
Sat  
M
Hol  
prior to the event/schedule for guaranteed recording.  
Apply to All CH  
No Recording  
Event  
Continuous  
Both(Cont&Evnt)  
OK  
Cancel  
58_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording Color Tags  
Color  
White  
Orange  
Blue  
Part Names  
Functions  
No Recording  
Continuous  
Event  
No schedule / event recording  
Scheduled recording only  
Event recording only  
Green  
Both(Cont&Evnt)  
Both scheduled / event recordings  
Each press of a selected cell will cycle through <No Recording>-<Continuous>-<Event>-  
<Both(Cont&Evnt)>.  
Event Record Duration  
You can set the beginning and ending point of a recording on an event.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Record> window to  
Event Record Duration  
move to <Event Record Duration>, and press [ENTER]  
CH  
1
Pre Event   
OFF  
POST Event   
1 min  
button.  
2
OFF  
1 min  
3
OFF  
1 min  
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
4
OFF  
1 min  
5
OFF  
1 min  
and set the value.  
6
OFF  
1 min  
7
OFF  
1 min  
• Pre Event : The recording of an event will start at a  
pre-determined time prior to the actual occurrence of the event.  
If it is set to 5 seconds, the recording begins from  
5 seconds before the event.  
8
OFF  
1 min  
Previous/Next Page  
OK  
Cancel  
• POST Event : The recording will continue for a  
pre-determined time after the actual end of an event.  
If it is set to 5 seconds, the recording ends in 5 seconds after an event.  
3. When the event recording duration setup is done, press <OK>.  
REC Quality / Resolution  
You can set resolution, FPS, and quality of recordings by channel, and by recording type of standard / event.  
For more information about the resolution, refer to the “Product Specification” section. (Page 120)  
Setting Standard Recording Properties  
You can set each channel’s resolution, quality and FPS for normal recordings.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Record> window to  
REC Quality & Resolution  
move to <REC Quality & Resolution>, and press  
Standard  
Event  
Remaining count : 1280H/4CIF : 8  
2CIF : 16  
CIF : 32  
[ENTER] button.  
CH  
1
Resolution  
CIF  
Record Rate   
7fps  
Record Quality   
  
  
  
  
  
  
  
  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
2. Select <Standard>.  
2
CIF  
7fps  
3
CIF  
7fps  
4
CIF  
7fps  
3. When the recording setup is done, press <OK>.  
5
CIF  
7fps  
6
CIF  
7fps  
7
CIF  
7fps  
8
CIF  
7fps  
Previous/Next Page  
OK  
Cancel  
English _59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Setting Event Recording Properties  
You can set each channel’s resolution, quality and FPS for event recordings.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Record> window to  
REC Quality & Resolution  
Event  
move to <REC Quality & Resolution>, and press  
Standard  
Remaining count : 1280H/4CIF : 8  
2CIF : 16  
CIF : 32  
[ENTER] button.  
CH  
1
Resolution  
4CIF  
Record Rate   
7fps  
Record Quality   
  
  
  
  
  
  
  
  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
Level4  
2. Select <Event>.  
2
4CIF  
7fps  
3
4CIF  
7fps  
Event recording setup window appears.  
4
4CIF  
7fps  
5
4CIF  
7fps  
6
4CIF  
7fps  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
7
4CIF  
7fps  
8
4CIF  
7fps  
and select it.  
Previous/Next Page  
• Resolution : Sets the resolution of the recorded screen.  
OK  
Cancel  
• Record Rate : Image Per Second, means the frames  
recorded per a second.  
• Record Quality : Sets the recording quality.  
4. When the Event recording setup is done, press <OK>.  
The estimated total remaining count means the total number of remaining recordings for both standard and event  
M
recordings.  
You cannot increase the remaining count if the current remaining count has reached zero or there is no available remaining  
count from any other page. If this is the case, reduce the remaining count for the current page, or do so for the same  
channel on any other page.  
Record Option  
You can set the recording to stop or overwrite when the HDD is full.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Record> window to  
Record Option  
move to <Record Option>, and press [ENTER] button.  
Disk End Mode  
Overwrite  
Disk End Beep  
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
AutoDelete
and set the value.  
The recording information will be deleted.  
Do you want to proceed?  
Reco
• Disk End Mode : If selected <Overwrite>, recording will  
continue despite the HDD full while overwriting the oldest.  
If selected <Stop>, the recording will stop when the HDD is  
full.  
HD
Re
Cancel  
OK  
OK  
Cancel  
• Disk End Beep : If selected <Stop>, the button is activated.  
If you check it, the beep will sound on the disk full and the  
recording stops.  
• Auto Delete : If you check it, Record Period setup is activated.  
If you specify the auto deletion period, the recording data before the period will be deleted automatically.  
This option will be enabled only if Disk End Mode is set to <Overwrite>.  
• HDD Free Space : Shows remaining free space available on the HDD.  
• Recordable (days/hours) : Shows estimation of remaining days and hours for recording, based on the  
remaining free space.  
3. When the recording option setup is done, press <OK>.  
60_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING THE EVENT  
You can set recording options when sensor, motion, image loss detection or tampering event occurs.  
Sensor Detection  
You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Return  
panel.  
2. Use the left/right button (◄ ►) to select <Event>.  
Event setting menu is selected.  
Event  
Sensor Detection  
Motion Detection  
Video Loss Detection  
Tampering Detection  
Alarm Schedule  
3. Use the up/down buttons (ꢀꢁ) to move to <Sensor  
Detection>, and press [ENTER] button.  
Sensor Detection  
Sensor  
Sensor Operation   
Cam   
Alarm   
None  
None  
None  
None  
None  
None  
None  
None  
Duration   
A window of sensor detection setup appears.  
1
2
3
4
5
6
7
8
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
1
2
3
4
5
6
7
8
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
4. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and set the value.  
• Sensor Operation : Sets the operation mode of sensors.  
Previous/Next Page  
- <OFF> : Sensor does not operate.  
- <N.O> : Sensor is opened.  
OK  
Cancel  
If the sensor is closed, it generates alarm.  
- <N.C> : Sensor is closed.  
If the sensor is open by interruption, it generates alarm.  
• Cam : Select a channel to be connected to the sensor.  
If selected camera, “Cam Preset setup” window appears.  
Select a channel and setup the preset.  
Sensor Detection  
SensCam Preset setup  
1
2
3
4
5
6
7
8
Preset  
CH  
1
2
3
4
5
6
7
8
Preset  
CH  
None  
9
None  
10  
Preset setup can be done in PTZ mode.  
None  
None  
None  
None  
11  
Refer to “Preset Setting”. (page 81)  
12  
None  
None  
None  
None  
13  
14  
None  
None  
None  
None  
15  
None  
None  
16  
OK  
Cancel  
OK  
Cancel  
• Alarm : Sets the alarm output method.  
Sensor Detection  
For further information on alarm output, refer to “HDD Alarm >  
Sensor  
Sensor Operation   
Cam   
Alarm   
Duration   
10 sec  
10 sec  
1
2
3
4
5
6
7
8
OFF  
1
2
None  
None  
Alarm”. (Page 53)  
AlaOrmFF Setup  
• Duration : Sets the duration of alarm signal and alarm  
1
4
2
3
BEEP  
All  
sound.  
OK  
Cancel  
5. When the sensor detection setup is done, press <OK>.  
Previous/Next Page  
OK  
Cancel  
English _61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Motion Detection  
You can set target detection region and motion, as well as the alarm signal output.  
When the motion detection region is set, it detects motion within the area.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Event> window to  
Motion Detection  
move to <Motion Detection>, and press [ENTER] button.  
CH  
1
Mode   
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
Sensitivity   
Level10(High)  
Level10(High)  
Level10(High)  
Level10(High)  
Level10(High)  
Level10(High)  
Level10(High)  
Level10(High)  
Alarm   
None  
None  
None  
None  
None  
None  
None  
None  
Alarm Duration   
A window of motion detection area setup appears.  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
2
3
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
4
5
and set the value.  
6
7
• Mode : Sets whether to activate motion detection.  
• Sensitivity : Sets the sensitivity level of the motion detection.  
• Alarm : Sets the alarm output method.  
8
Previous/Next Page  
Motion Region  
OK  
Cancel  
For further information on alarm output, refer to “HDD Alarm >  
Alarm”. (Page 53)  
• Alarm Duration : Sets the duration of alarm signal and alarm sound.  
3. When the motion detection setup is done, press <OK>.  
Setting the Motion Detection Area  
x
y
Select <Motion Region>.  
When “Motion Region” window appears, select a  
channel for detection and set the area of motion  
detection.  
• To set the area in “Motion Region” window  
In the “Motion Region” window, select desired region  
Motion Region  
CH1  
from <  
>.  
Apply to All CH  
Individual  
Cancel  
OK  
• To set the area using <Individual> selection  
In the “Motion Region” window, you can select cells  
individually by using <Individual>.  
When selected <Individual>, “Motion Region” window disappears and you can select cells one by one.  
When the motion area setup is done, press the <Menu> on the screen or the [MENU] button on the  
remote control or front panel to display the “Motion Region” window again.  
- Select : Selected cell is set to be a part of motion detection area.  
Select  
- Unselect : Selected cell is removed from the motion detection area.  
Unselect  
- Inverse : Unselected cells are set to be the motion detection area.  
Inverse  
- Menu : After selecting individual motion areas, move to the “Motion Region” window.  
Menu  
If selected <Apply to All CH>, selected motion area is applied to all channels.  
z
When the motion detection setup is done, press <OK>.  
62_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Loss Detection  
You can set the alarm to be generated on a camera disconnection, which causes a video loss.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Event> window to  
Video Loss Detection  
move to <Video Loss Detection>, and press [ENTER]  
CH  
1
Video Loss State   
Alarm   
None  
None  
None  
None  
None  
None  
None  
None  
Alarm Duration   
button.  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
2
A window of video loss detection area setup appears.  
3
4
5
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
6
7
and set the value.  
8
Previous/Next Page  
• Video Loss State : Sets whether to activate video loss  
detection.  
OK  
Cancel  
• Alarm : Sets the alarm output method.  
For further information on alarm output, refer to “HDD Alarm >  
Alarm”. (Page 53)  
• Alarm Duration : Sets the duration of alarm signal and alarm sound.  
3. When the video loss detection setup is done, press <OK>.  
Tampering Detection  
You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing  
direction, blocked lens and other overall change of scenes from the video.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Event> window to  
Tampering Detection  
move to <Tampering Detection>, and press [ENTER]  
CH  
1
Mode   
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
Sensitivity   
Medium  
Medium  
Medium  
Medium  
Medium  
Medium  
Medium  
Medium  
Alarm   
None  
None  
None  
None  
None  
None  
None  
None  
Duration   
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
10 sec  
button.  
2
Tampering detection settings screen appears.  
3
4
5
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
6
7
and set the value.  
8
Previous/Next Page  
• Mode : Set whether to use Tampering Detection or not.  
• Sensitivity : Set the sensitivity level of tampering detection.  
• Alarm : Set the alarm output method.  
OK  
Cancel  
• Duration : Set the alarm signal output and its dwell time.  
3. When the tampering detection setup is done, press <OK>.  
Since the tampering detection is designed and optimized to function in accordance with the user defined sensitivity level, it  
M
may not render a significant difference in detection with varied sensitivity in general monitoring situations.  
When the tampering detection mode is set <ON>, it is recommended that the pre event recording time of the corresponding  
channel should be set to 10 seconds or longer.  
English _63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Alarm Schedule  
You can set the conditions and operating hours for scheduled alarms.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Event> window to  
Alarm Schedule  
move to <Alarm Schedule>, and press [ENTER] button.  
Alarm1  
All  
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23  
2. Use direction buttons (ꢀꢁ◄►) to move to a desired item,  
Sun  
Mon  
Tue  
Wed  
Thu  
Fri  
and set the value.  
• Alarm : Sets the alarm output method.  
Sat  
For further information on alarm output, refer to “HDD Alarm >  
Hol  
OFF  
ON  
Event Sync  
Apply to All Alarm  
Alarm”. (Page 53)  
• ON : Marked in orange, and always generates alarm on  
scheduled time.  
OK  
Cancel  
• OFF : Marked in white, no alarm is generated even if an event occurs.  
• Event Sync : Marked in Blue, generates alarm only when an event occurs.  
• Apply to All Alarm : Applies the configured schedule to all  
Alarm Schedule  
alarms.  
Alarm1  
All  
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23  
Sun  
Mon  
Tue  
Wed  
Thu  
Fri  
Apply to All Alarm  
When the alarm is generated on the scheduled time, you can  
M
stop the alarm by canceling the schedule.  
Apply the alarm scheduling to all?  
OK  
Cancel  
Sat  
3. When the Alarm Schedule setup is done, press <OK>.  
Hol  
OFF  
ON  
Event Sync  
Apply to All Alarm  
OK  
Cancel  
BACKUP  
You can check the backup device and set the backup schedule by channel or by time.  
The product only supports external HDD of USB memory, CD/DVD and USB/SATA type. (Page 120)  
Setting the Backup  
You can backup the desired data to a connected device.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Return  
panel.  
2. Use the left/right button (◄ ►) to select <Backup>.  
Backup menu is selected.  
Backup  
Backup  
64_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Press the [ENTER] button.  
A backup window appears.  
Backup  
Start  
2014-01-01 00:01:06  
List0  
End  
2014-01-01 08:25:45  
You can directly access it from the “Live screen menu”.  
(Page 29)  
Overlap  
ALL  
1
9
2
3
4
5
6
7
8
10  
11  
12  
13  
14  
15  
16  
4. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Device  
Internal CD/...  
/20140101/  
Type  
SEC  
0001  
and set the value.  
Change  
Folder  
File Name  
Backup  
Used  
:
:
:
Check capacity  
• Backup Range : Sets the <Start> and <End> time for the  
Free  
backup.  
OK  
Cancel  
• Channel : Sets the channel to backup.  
You can select multiple channels.  
• Device : Select a backup device from the recognized devices.  
• Type : Sets the backup data format.  
- DVR : Saved data can be played back only by the DVR.  
- AVI : Saves the CODEC information provided by the DVR with the recording data, and saved data can be  
played back by using external viewers (such as Windows Media Player) on a PC.  
If you need to install a codec in Windows, run the x264_dvr.exe file in the codec folder that is created when you back up an  
AVI file.  
- SEC : Saves data in the Samsung’s proprietary format with built-in viewer, which supports immediate  
playback on a PC.  
• File Name : You can set the back file name.  
Refer to “Using Virtual Keyboard”. (Page 40)  
• Check capacity : Shows the size of the selected backup data, used and available capacity of the selected  
backup device.  
• Overlap : Shows a list of overlapping data on a same time according to the number of data.  
It appears when one channel has multiple data on a certain time point due to changing of time or time zone  
settings, etc.  
Refer to time and time zone of “Setting the Date/Time/Language”. (Page 38)  
5. When the backup setup is done, press <OK>.  
If no available device is recognized for backup, <OK> button is not activated.  
The application may slow down during the backup.  
J
You can switch to the menu screen during the backup in operation, but playback of data is not available.  
The data can be played back on a Webviewer while the backup is in progress but audio does not function.  
When a CD/DVD or memory device is used for backup, it is not available to use the full capacity of the media since the  
system consumes a part of its capacity.  
If a CD or DVD media causes errors, the disc tray opens and closes a several times, and eventually backup process will fail.  
In this case, replace the CD/DVD media and try again.  
If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the HDD is  
properly connected.  
Pressing the <Exit> during the backup will return to the previous menu, while the backup progresses.  
M
English _65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
NETWORK CONFIGURATION  
It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with  
events. You can configure the network environment which enables such functions.  
Connection Mode  
You can set the network connection route and protocol.  
Setting the Connection  
Sets the protocol and environment of the network.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Return  
panel.  
2. Use the left/right button (◄ ►) to select <Network>.  
Network menu is selected.  
Network  
3. Use the up/down buttons (ꢀꢁ) to move to <Connection  
Connection Mode  
DDNS  
Mode>, and press [ENTER] button.  
Live Transfer  
Mailing Service  
SNMP  
4. Select <Interface>.  
Connection Mode  
A window of connection mode setup appears.  
Interface  
Port  
Alarm  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
IP Type  
Static  
Transfer Bandwidth  
2Mbps  
and set the value.  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.200  
192.168.1.1  
255.255.255.0  
Manual  
• IP Type : Sets the network connection mode.  
• Transfer Bandwidth : Sets the maximum data flow to be  
transferred. (Upload speed)  
168.126.63.1  
Options will vary depending on the selected connection  
mode.  
OK  
Cancel  
- For <Static>, <DHCP> : Select one from 50 kbps ~  
2Mbps, and Unlimited.  
- For <PPPoE>, select one from 50 kbps ~ 600 kbps.  
66_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• IP Address, Gateway, Subnet Mask, and DNS  
Connection Mode  
Interface  
Port  
Alarm  
- For <Static> : You can directly input IP Address, Gateway,  
IP Type  
PPPoE  
Subnet Mask and DNS.  
Transfer Bandwidth  
600kbps  
- For <DHCP> : IP Address, Gateway, and Subnet Mask  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.200  
192.168.1.1  
255.255.255.0  
Manual  
are set automatically.  
168.126.63.1  
- For <PPPoE> : IP Address, Gateway, and Subnet Mask  
ID  
ID  
are set automatically.  
Password  
************  
• ID, Password : In case you selected PPPoE, provide the  
OK  
Cancel  
“ID” and its “Password”.  
DNS server for <DHCP> and <PPPoE> can be set by user only if you selected <Manual>.  
M
6. When the connection setup is done, press <OK>.  
Setting the Port  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
move to <Connection Mode>, and press [ENTER]  
button.  
Connection Mode  
Port  
Interface  
Alarm  
Protocol Type  
Device Port  
TCP  
4520  
~
4524  
2. Select <Port>.  
UDP Port  
8000 ~ 8160  
Unicast/Multicast  
Multicast IP Address  
Multicast TTL  
HTTP Port  
Unicast  
224.126.63.1  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
5
and set the value.  
80  
  
Secure Video Transmission  
ON  
OFF  
• Protocol Type : Select the protocol type between TCP and  
UDP.  
* Multi Browser Support:  
Device Port 4505~4530, HTTP Port 80  
OK  
Cancel  
- TCP : If compared to UDP, TCP connection is more stable  
but slow. Recommended for Internet connection.  
- UDP : If compared to TCP, UDP connection is less stable but fast. Recommended for use in LAN  
environment.  
If selected UDP, selections of Device Port, UDP Port and Unicast/Multicast are activated.  
If setting the connection mode to PPPoE, you cannot select UDP for the protocol type.  
• Device Port : Initially, <4520~4524> is set. It increases / decreases by 5.  
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet  
environments.  
• UDP Port : Initially, <8000~8160> is set. It increases / decreases by 160.  
• Unicast/Multicast : Select one between UDP-Unicast and UDP-Multicast.  
If selected Multicast, Multicast IP and TTL are activated.  
- UDP- Unicast : Transfers data packet to an individual client.  
- UDP-Multicast : Allows data communication to multiple clients causing no additional traffic to the network.  
• Multicast IP Address : User can directly input.  
• Multicast TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.  
• HTTP Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.  
• Secure Video Transmission : Send encrypted video.  
If it is set to <ON>, network performance can be limited.  
• Multi Browser Support : The Web Viewer can be used with a browser that supports the Silverlight.  
The multi viewer can be used only if the HTTP port is set to 80, protocol type is TCP and device ports range  
within 4505-4530.  
This is for the Siliverlight’s security purposes.  
4. When the protocol setup is done, press <OK>.  
English _67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Alarm setting  
1. In the <Network> setting window, press the top down  
(▲▼) button to move to the <Connection Mode> mode  
and press the [ENTER] button.  
Connection Mode  
Alarm  
Interface  
Port  
1
4
2
3
Disconnect Alarm Output Port  
BEEP  
All  
Duration  
OFF  
2. Select the <Alarm> menu.  
3. Press the top/down/left/right(▲▼◄►) button to toggle  
settings and set up your preferences.  
• Disconnect Alarm Output Port : Select a method for  
outputting an alarm when network connection is terminated.  
OK  
Cancel  
- If you select <1>, <2>, <3> or <4> the signal is outputted  
from the alarm output terminal in the rear.  
- If you select <BEEP>, the alarm sound will be played.  
- If you select <ALL>, the alarms sounds and the warning sounds from the rear will be heard at the same  
time.  
• Duration : Select the duration of alarm signal outputs and warning sounds.  
- It is outputted to the alarm output terminal (1, 2, 3, 4) selected in the connection cancellation alarm output  
port.  
- If you select <BEEP>, the alarm sound will be played.  
- If you select <ALL>, the alarms sounds and the warning sounds from the rear will be set at the same  
time.  
4. After finishing setting the alarms, select <OK>.  
68_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notification  
In a multi-browser environment, the <HTTP Port> should be set to 80 (private port).  
J
Select one between 4505 and 4530 for RTSP  
• Network Overview  
Cable/ADSL  
Modem  
Router (External IP: 109.112.92.133,  
Local IP: 192.168.1.1  
Internet  
DVR 2  
DDNS Server  
(www.samsungipolis.com)  
UB  
S
DVR 1  
Local PC  
System  
DVR 1  
DVR 2  
RTSP  
WEB  
RTSP  
WEB  
IP  
192.168.1.200  
192.168.1.200  
TCP  
192.168.1.202  
192.168.1.202  
TCP  
Protocol  
Private Port  
Public Port  
TCP  
80  
80  
TCP  
81  
81  
4520~4524  
4520~4524  
4525~4529  
4525~4529  
Connection Mode  
Connection Mode  
Interface  
Interface  
Port  
Alarm  
Port  
Alarm  
IP Type  
Static  
IP Type  
Static  
Transfer Bandwidth  
2Mbps  
Transfer Bandwidth  
2Mbps  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.200  
192.168.1.1  
255.255.255.0  
Manual  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.202  
192.168.1.1  
255.255.255.0  
Manual  
168.126.63.1  
168.126.63.1  
OK  
Cancel  
OK  
Cancel  
Connection Mode  
Connection Mode  
Port  
Port  
Interface  
Alarm  
Interface  
Alarm  
Protocol Type  
Device Port  
TCP  
Protocol Type  
Device Port  
TCP  
4520  
~
4524  
4525  
~
4529  
UDP Port  
8000 ~ 8160  
UDP Port  
8000 ~ 8160  
Unicast/Multicast  
Multicast IP Address  
Multicast TTL  
HTTP Port  
Unicast  
Unicast/Multicast  
Multicast IP Address  
Multicast TTL  
HTTP Port  
Unicast  
224.126.63.1  
224.126.63.1  
5
5
80  
81  
  
  
Secure Video Transmission  
ON  
OFF  
Secure Video Transmission  
ON  
OFF  
* Multi Browser Support:  
Device Port 4505~4530, HTTP Port 80  
* Multi Browser Support:  
Device Port 4505~4530, HTTP Port 80  
OK  
Cancel  
OK  
Cancel  
English _69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
• 1st Set Port Forwarding Setting  
Port Forwarding is 4520~4524  
(4520, 4521, 4522, 4523, 4524)  
Port Forwarding is 80  
SRD-1656D  
SRD-1656D  
192. 168. 1. 200  
192. 168. 1. 200  
TCP  
4520  
4520  
TCP  
80  
80  
• 2nd Set Port Forwarding Setting  
Port Forwarding is 4525~4529  
(4525, 4526, 4527, 4528, 4529)  
Port Forwarding is 81  
SRD-1656D  
SRD-1656D  
192. 168. 1. 202  
192. 168. 1. 202  
TCP  
4525  
4525  
TCP  
81  
81  
70_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting and Setting the Network  
Networking may differ from the connection method, check your environment before setting the connection mode.  
When no router is used  
• Static mode  
- Internet connection : Static PPPoE, leased line, and LAN environments allows connection between the DVR  
and remote user.  
- DVR Network Settings : Set the <Connection Mode> in  
Connection Mode  
<Interface> menu of the connected DVR to <Static>.  
Interface  
Port  
Alarm  
Consult your network manager for IP Address, Gateway and  
IP Type  
Static  
Transfer Bandwidth  
2Mbps  
Subnet Mask.  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.200  
192.168.1.1  
255.255.255.0  
Manual  
• DHCP mode  
168.126.63.1  
- Internet connection : Connect the DVR directly to a cable  
modem, DHCP PPPoE modem or FTTH network.  
OK  
Cancel  
- DVR Network Settings : Set the <Connection Mode> in  
<Interface> menu of the connected DVR to <DHCP>.  
• PPPoE mode  
- Internet connection : An PPPoE modem is directly connected to the DVR, where the PPPoE connection  
requires user ID and password.  
- DVR Network Settings : Set the <Connection Mode> in  
Connection Mode  
<Interface> menu of the connected DVR to <PPPoE>.  
Interface  
Port  
Alarm  
IP Type  
PPPoE  
<ID> and <Password> should be the same to the PPPoE user  
If you don’t know the ID and password, consult your PPPoE service  
Transfer Bandwidth  
600kbps  
information.  
IP Address  
Gateway  
Subnet Mask  
DNS  
192.168.1.200  
192.168.1.1  
255.255.255.0  
Manual  
provider.  
168.126.63.1  
ID  
ID  
Password  
************  
OK  
Cancel  
English _71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
When a router is used  
To avoid IP address conflict with the DVR's static IP, check followings :  
J
• Setting the DVR with a static IP  
- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem  
or a router in a Local Area Network (LAN) environment.  
• Setting the DVR Network  
1. Set the <Connection Mode> in <Interface> menu of the connected DVR to <Static>.  
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.  
IP Address, Gateway, and Subnet Mask : Consult your network manager.  
Check whether the set IP address is in the static IP range provided by the Broadband Router.  
If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should set  
J
the IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~ 192.168.0.254).  
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.  
• Setting the DHCP IP Address of the Broadband Router  
1. To access the Broadband Router’s configurations, open a web browser on the local PC that is connected  
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).  
2. At this stage, make the local PC's windows network configurations to the below example :  
Ex) IP Address : 192.168.1.2  
Subnet Mask : 255.255.255.0  
Gateway : 192.168.1.1  
- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User  
Name field, enter “admin” into the password field and press <OK> to access the router configurations.  
- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and  
end address.  
Set the start address (192.168.0.100) and end address (192.168.0.200).  
Above steps may differ from the router devices depending on the manufacturer.  
M
72_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Setting Router’s Port Forwarding  
1. Set the protocol to <TCP>.  
Connection Mode  
Port  
Interface  
Alarm  
2. External Port Range : Enter the TCP Port set in the  
<Device Port> in <Port> menu of the connected DVR.  
If more than one DVRs are connected to the router, the  
TCP port can be different.  
Protocol Type  
TCP  
Device Port  
4520  
~
4524  
UDP Port  
8000 ~ 8160  
Unicast/Multicast  
Multicast IP Address  
Multicast TTL  
HTTP Port  
Unicast  
224.126.63.1  
5
3. Internal PC IP Address : Enter the IP address set to the  
<IP Address> in <Interface> menu of the connected  
DVR.  
80  
  
Secure Video Transmission  
ON  
OFF  
* Multi Browser Support:  
Device Port 4505~4530, HTTP Port 80  
OK  
Cancel  
4. Internal Port Range : Set the same to the “External Port  
Range”.  
Above steps may differ from the router devices depending on the manufacturer.  
M
Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s network.  
DDNS  
You can set the DDNS site for a remote user’s network connection.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
move to <DDNS>, and press [ENTER] button.  
DDNS Setup screen appears.  
DDNS  
DDNS Site  
iPOLiS  
Server Name  
Product ID  
www.samsungipolis.com  
2. Use the virtual keyboard to enter the <Product ID>.  
Quick Connect  
Not Used  
Use  
DDNS Host Address  
http://www.samsungipolis.com/  
Refer to “Using Virtual Keyboard”. (Page 40)  
If selected <OFF> input fields are deactivated.  
If selected <iPOLiS>, the server name field is disabled.  
OK  
Cancel  
• DDNS Site : Set whether to use DDNS or not, and select  
the DDNS site if enabled.  
• Server Name : Enter the server name of the selected DDNS site.  
• Product ID : Enter the product ID which was registered to the DDNS site.  
• Quick Connect : Appears if the <DDNS Site> is set to <iPOLiS>.  
To use this feature, connect the DVR to a UPnP router and set to <Use>.  
If the quick connect setup has been cancelled while progressing, it is automatically set to <Not Used>.  
M
3. When the DDNS setup is done, press <OK>.  
English _73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
DDNS Setting  
DDNS is a short form of Dynamic Domain Naming System.  
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters  
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).  
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS  
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP  
system.  
• Setting DDNS in the DVR  
Set <Protocol Type> in the <Port> menu of the connected DVR to the following :  
Ex) Protocol Type : TCP  
Device Port : 4520~4524  
DDNS Site : iPOLiS  
• DDNS Settings of the Router  
Select the corresponding menu for the network transfer protocol of the router.  
• SETTING UP SAMSUNG iPOLiS DDNS  
Go to Your PC  
1. Open your browser and go to http://www.samsungipolis.com and click <LOGIN>.  
2. You first need to create an account.  
Click <SIGN UP>.  
3. Follow the account registration instructions on the website.  
4. After completing the account registration, login to your  
account.  
5. Add your DVR to your account. Click <PRODUCT  
REGISTRATION>.  
6. Create a name(Product ID) for your DVR. Use 4 to 20  
alphanumeric characters without spaces. Select  
classification, model number of the DVR and click  
<REGISTER>.  
7. After registration, you should see your product in the list.  
74_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Go back to DVR  
1. From network tab, click on <DDNS>.  
Logout  
Return  
Network  
Connection Mode  
DDNS  
Live Transfer  
Mailing Service  
SNMP  
2. Under DDNS Site, select <iPOLiS>.  
DDNS  
DDNS Site  
iPOLiS  
Server Name  
Product ID  
www.samsungipolis.com  
Quick Connect  
Not Used  
Use  
DDNS Host Address  
http://www.samsungipolis.com/  
OK  
Cancel  
3. Under Product ID, enter the product ID you created on the  
Samsung iPOLiS website.  
DDNS  
DDNS Site  
iPOLiS  
Under Quick Connect, select <Use> and click <OK>.  
Server Name  
Product ID  
www.samsungipolis.com  
srd1656dhome  
Quick Connect  
Not Used  
Use  
DDNS Host Address  
http://www.samsungipolis.com/srd1656dhome  
OK  
Cancel  
If the connection was not successful, your router may not be  
supporting UPNP.  
DDNS  
M
DDNS Site  
iPOLiS  
www.samsungipolis.com  
For more information on enabling UPNP on your router, please  
see Router manual.  
Server Name  
ProduConnection
Quick
Quick Connect Success  
DDN
OK  
OK  
Cancel  
English _75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Live Transfer  
Sets the quality of the image that is transferred from the DVR to the network.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
Live Transfer  
move to <Live Transfer>, and press [ENTER] button.  
CH  
1
Resolution   
Quality   
Low  
The Live Transfer window appears.  
CIF  
CIF  
CIF  
CIF  
CIF  
CIF  
CIF  
CIF  
2
Low  
3
Low  
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
4
Low  
5
Low  
and set the value.  
6
Low  
7
Low  
• Resolution: Shows the selected network profile’s resolution  
setting.  
8
Low  
Previous/Next Page  
• Quality: Shows the selected network profile’s image quality  
OK  
Cancel  
setting.  
3. When the live transfer is done, press <OK>.  
Mailing Service  
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.  
If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set to  
M
J
<OFF>, only the text notification will be sent to the applicable email address.  
If you set the interval of the e-mail notice too short, the e-mail server may consider it as spam that will not be transferred  
normally.  
SMTP Setting  
Sets the SMTP mail server.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
Mailing Service  
move to <Mailing Service>, and press [ENTER] button.  
SMTP  
Event  
Group  
Recipient  
ServerType  
SMTP mail Server  
2. Select <SMTP>.  
Server Address  
Port  
25  
You will see the SMTP setting window.  
Use Authentication  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
ID  
Password  
and set the value.  
Secure Transfer  
Sender Address  
E-mail Test  
Never  
ex. [email protected]  
• ServerType : Displays the connected server type.  
• Server Address : Enter a server to connect to.  
• Port : Sets the communication port.  
OK  
Cancel  
• Use Authentication : Check this if the SMTP server uses user authentication.  
The account input box will be activated.  
• ID : Enter a user to use authentication when connecting to the SMTP server.  
• Password : Enter the password of the SMTP server user.  
76_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Secure Transfer : Select one from <Never> and <TLS (if available)>.  
• Sender Address : Use the virtual keyboard to enter the sender’s e-mail address.  
Refer to “Using Virtual Keyboard”. (Page 40)  
• E-mail Test : Conducts the test on the server settings.  
4. When the SMTP setup is done, press <OK>.  
Event Setting  
You can set the interval and type of the event that will be sent to the user.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
Mailing Service  
move to <Mailing Service>, and press [ENTER] button.  
Event  
SMTP  
Group  
Recipient  
Event Interval  
10 min  
2. Select <Event>.  
The number of attached images for each event  
1
Use Event Transfer  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Sensor  
Motion  
Tampering  
Video Loss  
and set the value.  
Change P/W  
Power On/Off  
HDD Info  
Manual Record  
• Event Interval : Set the event interval.  
If a series of events occurs, the e-mail will be sent at the specified  
interval, not on each event.  
OK  
Cancel  
• The number of attached images for each event : Set the  
number of images attached to the e-mail sent in case an event occurs.  
Can attach 1 to 5.  
• Use Event Transfer : Select an event type to send if an event occurs.  
If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.  
4. When the event setup is done, press <OK>.  
Group Setting  
You can set the group to whom the e-mail is sent, and specify the permission for each group.  
You can add recipients for each group in the <Recipient> menu item.  
The recipient is set separately from the DVR user group.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
Mailing Service  
move to <Mailing Service>, and press [ENTER] button.  
Group  
SMTP  
Event  
Recipient  
Group  
Add  
Delete  
Rename  
2. Select <Group>.  
Recipient Permission  
Sensor  
Motion  
Tampering  
Video Loss  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Change P/W  
Power On/Off  
HDD Info  
and set the value.  
Manual Record  
• Add : Select <Add> and use the virtual keyboard to add a  
group.  
Refer to “Using Virtual Keyboard”. (Page 40)  
OK  
Cancel  
• Delete : Deletes the selected group.  
• Rename : You can reset the recipient permission of an existing group.  
• Recipient Permission : Set the permission of the recipient group.  
4. When the group setup is done, press <OK>.  
English _77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Recipient Setting  
You can add/remove a recipient(s) to/from the specified group and edit the group if necessary.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
Mailing Service  
move to <Mailing Service>, and press [ENTER] button.  
Recipient  
SMTP  
Event  
Group  
Group  
All Group  
Add  
2. Select <Recipient>.  
Group  
Name  
e-Mail Address  
Delete  
3. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and set the value.  
Previous/Next Page  
OK  
Cancel  
• Add : You can select a recipient name, e-mail address or  
group.  
Mailing Service  
Recipient  
SMTP  
Event  
Group  
You should have created a group in the <Group> menu  
Group  
ABC  
Add  
GroAdd recipient
Delete  
item before you can add a user to the group.  
Name  
For inputting the recipient name and email address, refer to  
Email  
Select Group  
ABC  
“Using Virtual Keyboard”. (Page 40)  
OK  
Cancel  
4. When the recipient setup is done, press <OK>.  
Previous/Next Page  
OK  
Cancel  
SNMP  
You can configure the settings for the SNMP protocol.  
Using the mouse may help make setup easier.  
1. Use the up/down buttons (ꢀꢁ) in <Network> window to  
move to <SNMP>, and press [ENTER] button.  
The SNMP setup screen appears.  
SNMP  
Enable SNMP v1  
2. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
Enable SNMP v2c  
Read Community  
public  
write  
and set the value.  
Write Community  
• Enable SNMP v1 : SNMP version 1 will be active.  
• Enable SNMP v2c : SNMP version 2 will be active.  
- Read Community : Read community where you can  
access objects that support the SNMP protocols.  
OK  
Cancel  
- Write Community : Write community where you can  
access objects that support the SNMP protocols.  
3. When the SNMP setup is done, press <OK>.  
78_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING A PTZ DEVICE  
The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference.  
PTZ Device  
TGhee tPtTinZ gdevsictearctaendbewacittivhatPedToZnly if a channel in connection with the PTZ camera is selected.  
The PTZ camera is available, only if a channel is selected, in the following way :  
Using the remote control buttons  
2014-01-01 01:10:25  
Scene Mode  
Press the [PTZ] button on the remote control.  
Spot Out 1  
Spot Out 2  
PTZ Control  
Zoom In  
Audio  
Using the launcher menu  
PTZ  
Click <  
> to display the live launcher.  
Freeze  
Stop Alarm  
Record  
Using the right-click menu in Live mode  
Right-click any area on the screen to display the context menu, and  
select <PTZ Control>.  
Play  
Search  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Logout  
Using icons on the live screen  
2014-01-01 01:10:25  
Click the <  
> icon on the live screen.  
The PTZ function is available only if the PTZ camera is connected  
so that the < > icon is displayed on the screen.  
M
English _79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
main menu  
Using the PTZ camera  
You can use one camera to perform all functions of PAN, TILT and ZOOM for monitoring multiple places and  
set the preset to your preference in a desired mode.  
1. Launch the <PTZ Control> menu.  
2014-01-01 01:10:25  
As the <  
> icon on the bottom right corner turns  
yellow, you access the “PTZ Control” mode to display the  
“PTZ Control” menu.  
Be sure to configure PTZ working environments before operation,  
since the PTZ Working(Active) mark can be appeared to be  
activated even when PTZ is not operative.  
M
PTZ Control CAM01  
Swing  
Group  
Trace  
Preset  
Tour  
Select  
Select  
Select  
Select  
Camera Setup  
Select Preset  
Save Rename  
Delete Delete All  
2. Use the PTZ wheel in the launcher menu to adjust the  
monitoring area, or use the direction buttons (ꢀꢁ◄ ►) on  
the remote control to move the camera to a desired place.  
Exit  
• PTZ Wheel : Clicking a nearer point to the center will move in that direction slowly; clicking a farther point  
from the center will move fast.  
Keep clicking left to rotate the lens counter clockwise; keep clicking right to rotate the lens clockwise.  
• Zoom (  
) : You can use the Zoom function of the PTZ camera.  
) : Adjusts the intensity of radiation incoming to the iris.  
) : Enables you to adjust the focus manually.  
• IRIS (  
• Focus (  
• Swing : Moves between the preset start point and end point.  
• Group : Moves in the path specified by combining the preset, pattern and auto pan.  
• Trace : Moves camera’s framing in the predefined path.  
• Preset : Sets the preset position for camera framing and moves to designated preset position when  
selecting a desired preset.  
• Tour : Moves in the path specified by combining multiple groups.  
For the coaxial communications, the operation may differ depending on the protocol.  
For the <Coaxizzal> type, SRD-876D/1656D/1676D is supported.  
Before entering the PTZ device control mode, set the values of the PTZ device in the <Setting the PTZ> menu.  
M
(Page 50)  
For camera specifications that supports PTZ comtrol depending on communication method, refer to our web site.  
80_ main menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preset Setting  
A preset is a set of specific target points of a PTZ camera, and up to 127 presets per a camera can be stored.  
Using the mouse may help make setup easier.  
1. In PTZ Control mode, use the direction buttons to adjust the camera in a desired direction.  
2. Select the <Save> key.  
The virtual keyboard for inputting the preset will appear.  
Refer to “Using Virtual Keyboard”. (Page 40)  
• Save : You can add and save the preset.  
• Rename : You can change the settings of the existing presets.  
• Delete : Deletes the selected preset.  
• Delete All : Deletes all existing presets.  
If you replace the camera of the channel that stores the preset list with a new one, you should reset the preset accordingly.  
M
3. Press <OK>.  
The preset will be saved as a name that you entered.  
Camera Setting  
A PTZ camera has its own menu system. Optimize the PTZ camera according to the DVR.  
Using the mouse may help make setup easier.  
• Select <Camera Setup> in the PTZ Control menu.  
2014-01-01 01:10:25  
The camera-specific menu appears.  
You can configure the settings of those cameras that support the  
protocols of Samsung, Pelco C/D/P, AD, ELMO, GE, CCVC and  
Panasonic.  
If you are setting Auto Pan or Pattern in the camera menu, press  
and hold the appropriate button for a certain time so that the  
button operation can be different from that in normal PTZ setting.  
Camera Setup  
Exit  
English _81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
search & play  
SEARCH  
You can perform the search for recorded data by the time or by the search criteria such as an event.  
You can access the <Search> menu directly in Live mode.  
1. In Live mode, right-click any area of the screen.  
2014-01-01 01:10:25  
Scene Mode  
The Live menu appears.  
Spot Out 1  
Spot Out 2  
Audio Off  
Freeze  
2. Select <Search>.  
Or, press the [SEARCH] button on the remote control or  
the front panel.  
Stop Alarm  
Record  
Play  
Search  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Logout  
3. The Search menu appears.  
2014-01-01 01:10:25  
If you have not checked <POS USE> in the “Main Menu > Device  
> POS Device” menu, the Search menu does not include the <POS  
Search> item. (Page 54)  
Return  
Time Search  
Event Search  
Backup Search  
POS Search  
4. The search can be restricted by the Auto Delete function.  
Refer to “Setting the Recording > Record Option”.  
(Page 60)  
Motion Search  
Overlapped data : It only appears if there exists overlapped data  
on a certain time, produced due to the change of DVR’s time  
setup. The latest data comes first, from <List0>.  
It does not appear in <Backup Search>.  
M
Time Search  
You can search for recorded data of a desired time.  
As the time to display may be different depending on the time zone and the DST standard time, the time of  
data recorded in the same time can be displayed differently depending on time zone and DST settings.  
Using the mouse may help make setup easier.  
1. Select <Time Search> in the <Search> menu.  
Time Search  
2014-01-01  
Go to First  
Go to Last  
2. Select a date to search.  
Overlapped Data List1  
Zoom In  
Data  
Zoom Out  
00:01  
Refer to “Using the Calendar”. (Page 39)  
All  
CAM 01  
CAM 02  
CAM 03  
CAM 04  
CAM 05  
CAM 06  
CAM 07  
3. The record data on the specific date will be listed.  
The display bar is different according to the data type.  
So check the data type for the color in the left pane.  
2014/01/01 00:01:17  
Standard  
Motion  
Schedule  
Sensor  
Etc  
V.Loss  
Previous/Next Page  
Tampering  
4. Use direction buttons (ꢀꢁ◄ ►) to set the search criteria  
Play  
Return  
and press the [ENTER] button.  
• Go to First : Moves to the earliest date.  
• Go to Last : Moves to the most recent date.  
• Time : Enter a time to perform the search or use the up/down button <>> to select one.  
• Previous/Next Page : Moves to the previous / next page. (Use the remote control or the buttons on the front  
panel.)  
82_ search & play  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Zoom In : The map enlarges in detail.  
It will switch in the sequence of 24 hours - 16 hours - 8 hours  
- 4 hours.  
Time Search  
Go to First  
Go to Last  
2014-01-01  
Overlapped Data List1  
Zoom In  
Data  
Zoom Out  
00:01  
All  
• Zoom Out : The map will switch in the reverse order of the  
detailed mode above.  
CAM 01  
CAM 02  
CAM 03  
CAM 04  
CAM 05  
CAM 06  
CAM 07  
2014/01/01 00:01:17  
It will switch in the sequence of 4 hours - 8 hours - 16 hours  
- 24 hours.  
Standard  
Motion  
Schedule  
Sensor  
Etc  
V.Loss  
Previous/Next Page  
Tampering  
Double-click a desired time to zoom it in/out.  
Play  
Return  
M
• Preview : Click <Channel> and select (click, drag) a time in  
<Duration> to display a still image for the portion.  
- If the selected channel does not contain any recorded data, it will be marked black.  
5. Select a data item and click <Play>.  
The screen switches to the data playback mode.  
Event Search  
You can search for events by the channel and play them.  
Using the mouse may help make setup easier.  
1. Select <Event Search> in the <Search> menu.  
Event Search  
CAM 01  
2. Use direction buttons (ꢀꢁ◄ ►) to set the search criteria  
2014-01-01  
View all  
Go to First  
and press the [ENTER] button.  
Overlapped Data List1  
Go to Last  
No.  
Date/Time Preview  
02:47:54 ~ 02:48:59  
00:39:06 ~ 00:40:30  
00:01:22 ~ 00:02:28  
Event  
Motion  
Motion  
Motion  
All record events on a specific date will be found. (Normal/Schedule  
3
2
1
recording included)  
2014/01/01 00:01:22  
• Date/Time Preview : If you select a data item in the list, the  
still image of the selected data will be displayed in the left  
preview pane.  
Previous/Next Page  
Play  
Return  
• Event : Displays the type of the event that occurred.  
3. Select a data item and click <Play>.  
The screen switches to the event data playback mode.  
Backup Search  
Searches for backup data in the connected backup device.  
Only data in the format of DVR is included in the search.  
Refer to <Type> in “Backup > Setting the Backup”. (Page 64)  
Using the mouse may help make setup easier.  
1. Select <Backup Search> in the <Search> menu.  
Backup Search  
USB:USB2FlashStorage  
2. Use direction buttons (ꢀꢁ◄ ►) to set the search criteria  
No.  
1
Folder Name  
20140101  
File Name  
16190000  
and press the [ENTER] button.  
• Record Period : Displays the record period.  
• Channel info : Displays the recorded channel.  
• Play Start Time : Select a time that you start playing.  
Previous/Next Page  
File Name  
Channel info  
2014-01-01 01:01:01 - 2014-01-01 01:01:10  
Record Period  
Play Start Time  
2014-01-01  
16:30:52  
3. Select a data item and click <Play>.  
Play  
Return  
The screen switches to the backup data playback mode.  
English _83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
search & play  
POS Search  
You can search for data in the POS device that is connected to the DVR.  
You can use the mouse to select the related items.  
1. Select <POS Search> in the <Search> menu.  
POS Search  
Date/Time  
2014-01-01 02:41:18  
2014-01-01 03:41:18  
Case Sensitive  
Search  
Whole Word  
2. Use direction buttons (ꢀꢁ◄ ►) to set the search criteria  
Keyword  
and press the [ENTER] button.  
Overlapped Data List1  
Go to First  
Go to Last  
POS  
CH  
1
Start Date/Time  
Keyword  
CHANGE _  
CASH _  
You can enter specific text to refine your search.  
1
1
1
2014-01-01 03:41:15  
2014-01-01 03:41:15  
2014-01-01 03:41:10  
1
1
CASH _  
• Keyword : Use the virtual keyboard to enter a keyword.  
2014/01/01 03:41:15  
• Search Criteria :  
CHANGE  
5.95  
Previous/Next Page  
- <Case Sensitive> : If selected, search will be performed  
Play  
Return  
case-sensitively.  
- <Whole Word> : If selected, only the exact matches with  
the keyword will be found.  
• Preview : Select a data item in the list to display the preview image.  
Information about the image will be displayed on the bottom of the screen.  
•
: You can use these buttons to accelerate your search if you have a huge list of search results.  
3. Select a data item and click <Play>.  
The screen switches to the POS data playback mode.  
Motion Search  
If a motion is detected in each channel, you can set a desired area to perform the search.  
You can use the mouse to select the related items.  
1. Select <Motion Search> in the <Search> menu.  
Motion Search  
Setup  
Channel  
CAM 01  
Motion Region  
All Area  
2. Use direction buttons (ꢀꢁ◄ ►) to set the search criteria  
Date/Time  
2014-01-01 03:41:18  
2014-01-01 05:11:44  
Go to First  
Search  
and press the [ENTER] button.  
Overlapped Data List1  
Go to Last  
No.  
7
Start Time  
01:01:30  
01:01:25  
01:01:20  
01:01:15  
01:01:10  
01:01:05  
01:01:01  
If you set the motion area to <Manual Area>, the <Setup> button  
6
will be activated.  
5
4
3
2014/01/01 01:01:30  
• Motion Region : Select an area to perform the search.  
2
1
- All Area : Searches for all areas of the selected channel.  
Previous/Next Page  
Play  
Return  
- Current Area : Searches for the motion area for each  
channel specified in “Motion Detection >  
Setting the Motion Detection Area”. (Page 62)  
- Manual Area : You can set the motion area manually.  
• Setup : The Setup button will be activated only if you have  
set the motion area to Manual. Press this button to display  
the area setting window.  
• Date/Time : The Date/Time will be automatically set by the  
hour, and the end time will be automatically set to one hour  
later than the start time if it is set.  
Motion Region  
CH1  
• Preview : Select a data item in the list to display the still  
Apply to All CH  
Individual  
Cancel  
OK  
image of the item.  
3. Select a data item and click <Play>.  
The screen switches to the motion data playback mode.  
84_ search & play  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
Play  
You can play data stored in the HDD and backup a desired portion of the data.  
Using the mouse may help make setup easier.  
1. In Live mode, click <Play> in the right-click menu or  
2014-01-01 01:10:25  
<
> in the launcher menu, or press the Play button on  
Scene Mode  
Spot Out 1  
Spot Out 2  
Audio Off  
Freeze  
the remote control or the front panel.  
2. Use the up/down button (ꢀꢁ) to select a menu.  
Stop Alarm  
Record  
Play  
For data search, refer to <Search>. (Page 82)  
Search  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Logout  
3. Select a data item and click <Play> in the Search menu.  
The selected data is played and the play launcher appears  
on the screen.  
2014-01-01 01:10:25  
If there is an existing data, <Play> will start immediately without  
performing the search.  
• Playback Information : Displays the date and time of the  
current data in the top corner.  
REC  
• Backup : Click <  
> to set the current time to the start  
Backup Range  
time of backup; you can specify a backup area using the  
mouse (yellow triangle).  
Start  
2014-01-01 00:01:06  
End  
2014-01-01 01:10:25  
Device  
Internal CD/...  
/20140101/  
Type  
SEC  
0001  
Click <  
> again to set the current time to the end time of  
Folder  
File Name  
Change  
the backup and the “Backup Range” window appears.  
Backup  
Used  
:
:
:
Check capacity  
Free  
- Type : Supports formats of DVR, AVI and SEC.  
Refer to a list of formats in “Setting the Backup”.  
(Page 64)  
- Device : Select a backup device.  
OK  
Cancel  
- Check Capacity : Enables you to check the capacity of  
the selected storage device.  
4. If you want to return to the Live screen in Play mode, click <  
> in the launcher menu or press the  
[ ] button on the remote control or the front panel.  
English _85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
search & play  
Using the Playback Button  
REC  
Part Names  
Functions  
Play Timeline  
Indicates the current playback point, and can be used to move.  
a
b
Skip Backward  
Moves backward by unit time. (Move by 10 minutes)  
Backward Fast  
Used for quick backward playback. (2 - 64x speed)  
c
d
Play  
Backward Slow  
Play  
Used for backward frame-by-frame search while in PAUSE. (1/2 - 1/8x speed)  
Step Backward  
Pause  
Stop  
Moves backward by one frame at a time.  
Stops playing the current video temporarily.  
Stops playback and moves to the live screen.  
e
f
g
h
Step Forward  
Moves forward by one frame at a time.  
Ensured to play forward up to 4 channels simultaneously at a low speed. (1/2 - 1/8x speed)  
Forward Slow  
In a split mode, the real time playback may not be supported, depending on the record quality,  
resolution and number of channels. And some frame rates may be supported.  
i
Play  
Forward Fast Play Used for quick forward playback. (2 - 64x speed)  
j
k
l
m
n
Skip Forward  
Return  
Audio  
Moves forward by unit time. (Move by 10 minutes)  
Return to the search setup screen.  
Sets Audio ON/OFF.  
REC  
Records all channels in Live mode.  
Begins backup of the selected section of the video being played, with the specified starting/ending  
Partial Backup  
o
p
point.  
Click a desired playback mode or press [MODE] to switch the screen mode in sequence.  
Mode Switch  
The grey area in the center of the 13-split mode plays the Live channel.  
The default channel of the Live mode is CH1, which can be changed later.  
86_ search & play  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
INTRODUCING WEB VIEWER  
What is Web Viewer?  
Web Viewer allows remote access to your DVRs. You have  
access to li ve video, archived video, PTZ control  
(if configured), etc.  
Product Features  
Network  
• Remote access from a standard browser  
• Supports PTZ camera controls  
G
• Supports 1, 4, 9, 16 camera viewing formats (maximum of  
16 cameras in the list).  
• Gets jpeg, bmp or png format images to print and save to “Print or Save jpeg, bmp or png format images”.  
• Record video in AVI format-compatible with popular media players. (needed the H.264 codec)  
System Requirements  
The following lists the recommended suggest hardware and operating system requirements needed to run  
the Web Viewer.  
Windows XP SP3 or higher  
Windows Vista  
OS  
Windows 7  
Mac OS 10.6 and later versions  
- Windows OS : Internet Explorer 8, 9, 10, Firefox 3.6 or higher, Chrome 12 or  
Web Browser  
higher  
- Mac OS : Safari 5 or higher, Firefox 3.6 or higher.  
CPU  
Intel Core i7 3.4Ghz  
4 GB or more  
Memory  
50 MB (Installation space required)  
HDD  
* Additional HDD space required for recording.  
Recorded file size will vary depending on recording quality settings.  
English _87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
CONNECTING WEB VIEWER (Windows)  
1. Open your web browser and type the IP address or URL of  
DVR into the URL address box.  
“192.168.1.200” is set to IP by default.  
M
Set to an available IP address in IP Installer or "Network >  
Connection Mode”.  
The URL connection will be enabled only when the DDNS connection settings have been completed.  
2. A user with the admin permissions should provide the  
admin ID and password. A registered user should provide  
the user ID and password.  
The default administrator ID is “admin”, and the password must  
J
M
be set when the user log in at the first time.  
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or  
using the default wireless router password may expose your video data to potential threat.  
To prevent from your personal information being exposed, please change your password every 3 months. Note that the  
security and other related issues caused by careless management of password shall be be in the charge of the user.  
If there are more than one LAN cards for the PC, you can use a LAN card with a smaller interface matrix value in order to  
receive video.  
It allows up to 10 simultaneous access including the Admin and general users.  
It does not allow multiple login of the Admin user.  
Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.  
Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the  
Web Viewer. (Page 43)  
All settings are applied by the DVR’s settings.  
If you change such as the permission settings with logged in to the Web Viewer, you may go back to the log in  
screen.  
3. Click <Install ActiveX Control...>.  
4. When the installation confirm message appear, click [Yes]  
button.  
All windows will be closed(IE).  
88_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. When a program installation wizard window appears, press  
the [Install] button to install the program.  
6. When the program is installed, open the web viewer again  
to login.  
Live Viewer's main screen appears when you log in  
successfully after installing the program.  
English _89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
USING LIVE VIEWER (Windows)  
The Live Viewer screen consists of following :  
j i  
a
b
c
d
e
f
g
h
Menu  
Menu Selection  
Functions  
Switches into corresponding menu screen by clicking each menu.  
a
b
c
d
Address, Name, Time  
DVR Time, PC Time  
Split Mode Selection  
Displays the IP, model name, time, etc. of connected DVR.  
Select <DVR Time> or <PC Time> for the OSD time information display setting of the Live Viewer.  
Selects the type of split screen and specify the channel displayed in Display Pane.  
Switches into previous/next channel or perform Auto Sequence.  
Change Channel  
e
Click Auto Sequence button to display the Time Interval Selection menu.  
CAPTURE  
PRINT  
AVI Save  
Saves current video for selected channel in designated path.  
Prints current video image for selected channel through designated printer.  
Records the live video in AVI file format in designated path, and then stops recording.  
f
Recording status icon is displayed on screen during recording.  
Audio  
OSD  
Sets the sound connected to each channel to ON/OFF.  
Select the format of OSD information that will be displayed.  
90_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Functions  
PTZ  
Controls connect PTZ camera(s).  
g
Goes to the relevant menu screen of a camera, which supports OSD menu and changes  
OSD Menu  
the menu.  
Display Pane  
Logout  
User ID  
Displays the video of camera connected to DVR.  
Click Logout icon for logout.  
h
i
j
Displays the user's ID.  
Dual Stream selection: Right click on any of live channels, there will be a drop-down menu profile1/profile2. The  
default setting is profile1, that's to say, video displayed as profile1 resolution. If you select profile2, Video will be  
displayed as profile2 resolution.  
M
profile1: Live transfer resolution, Profile 2: Recording resolution  
OSD Information Display  
a The channel number of the connected DVR are displayed.  
a
b
b Either the <DVR Time> or the <PC Time> will be displayed as the  
current date and time, according to your configuration.  
c It displays whether the PTZ controls are active.  
d Shows Audio On/Off status.  
e Alarm icon appears when alarm is issued.  
It disappears when pressed the [ALARM] button of the DVR.  
f Motion icon appears when a motion is detected.  
g Tampering icon appears when a tampering is detected.  
h Shows the recording status.  
c d e f g h  
If you have set PTZ cameras for the DVR, “PTZ” is displayed on the  
screen. Select a PTZ camera channel and use the [PTZ] button for  
camera control.  
M
Connected DVR  
This displays the IP address and the status of the connecting  
DVR.  
Connection failure message  
M
No Response : Appears when the DVR does not respond.  
Access Denied : Appears when the maximum number of  
users is exceeded.  
The number of simultaneous connections are limited to 10.  
Setting the Display of the OSD Time Information  
Select <DVR Time> or <PC Time> for the OSD time  
information display setting.  
• DVR Time : Based on the time of the connected DVR  
• PC Time : Based on the time of the PC currently running  
the Web Viewer.  
English _91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Split-Screen  
Click split mode selection button to switch to the  
corresponding screen mode.  
SINGLE MODE  
QUAD MODE  
NINE MODE  
SIXTEEN MODE  
To switch to full screen mode  
Click <  
>.  
Current split screen appears in full screen.  
Press the [ESC] key to exit the full screen mode.  
92_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Live Screen Mode  
16-split mode does not support “Sequence”, “Previous” and  
“Next”.  
•
: When this button is clicked, the previous screen  
appears.  
- In SINGLE MODE, the channel numbers are switched in  
reverse order.  
- In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 2nd 4 channels (5~8)   
3rd 4 channels (9~12) 4th 4 channels (13~16).  
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).  
: When this button is clicked, the next screen appears.  
•
•
- In SINGLE MODE, the channel numbers are sequentially switched from 1 to 16.  
- In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 2nd 4 channels (5~8)   
3rd 4 channels (9~12) 4th 4 channels (13~16).  
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).  
: When this button is clicked, screens are switched at a  
preset interval.  
- In SINGLE MODE, the channel numbers are sequentially  
switched from 1 to 16.  
- In QUAD MODE, the screens are changed like  
1st 4 channels (1~4) 2nd 4 channels (5~8)   
3rd 4 channels (9~12) 4th 4 channels (13~16).  
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).  
Default setting time (10 seconds)  
To capture a screen  
1. Click <  
> button.  
When a pop-up window appears, select the saving path  
for captured image.  
2. Select the path and name the file. And then click the  
<Save> button.  
3. Save current camera’s video image as .bmp, .jpg or .png  
file.  
If the browser does not operate in admin mode for Windows  
J
vista/7, when you save the capture file, there can be problems in saving it as bmp, jpg or png.  
English _93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
To print a screen  
1. Click <  
> button.  
2. Print current camera’s video image with the printer  
connected to the PC operating the Web Viewer.  
To save as AVI  
1. Click <  
> button.  
When “AVI Setup” window appears, select the record  
saving path and capacity.  
2. Select a desired path, enter the maximum recording  
capacity, and then click <OK> button.  
Save current channel’s video as AVI file. For playing a video clip,  
you can use the free video player to play the video.  
(ex: GOM Player, KM Player, etc.)  
After saving an AVI file, install the CODEC when playing it in Windows Media Player.  
However, the video may not played properly, depending on the CODEC compliance of the player.  
At least 1GB of free space is required for recording.  
While recording current data in Web Viewer, you cannot select Split Mode buttons, switch to the previous/next  
screen, or activate Auto Sequence function.  
J
If the viewer is running without the administrator’s permission in Windows Vista / 7, you may not change a folder  
Audiowhen saving a video as AVI file.  
•
: Sets audio of each connected channel to On/Off.  
OSD  
•
: Select Show OSD on the Live screen.  
94_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING A CONNECTED PTZ CAMERA  
Controlling PTZ  
If PTZ camera is connected, the <  
> icon appears on screen. When selecting corresponding camera  
channel, the PTZ tab is provided to allow you to control the PTZ.  
k
j
i
a
b
c d e f g h  
Part Names  
Direction Adjustment  
Functions  
Adjusts the direction of a camera.  
a
b
PT Speed  
Adjusts the PAN, TILT reaction speed.  
Sets the preset position for camera framing and moves to designated preset position  
when selecting a desired preset.  
Preset  
c
Swing  
Group  
Tour  
Moves between the preset start point and end point.  
Moves in the path specified by combining the preset, pattern and auto pan.  
Moves in the path specified by combining multiple groups.  
Moves camera’s framing in the predefined path.  
Click or drag on the screen to control PTZ.  
d
e
f
g
h
i
j
k
Trace  
PowerPTZ  
Focus  
IRIS  
Adjusts the focus of the camera.  
Adjusts image’s brightness by controling the camera’s iris.  
Zooms in/out the image by controling camera’s zoom.  
ZOOM  
English _95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
To set a preset  
1. Click <  
> button to display “Preset” window.  
2. Click <  
> to select a desired preset number.  
3. Enter the name of preset.  
4. Use direction keys to adjust the direction which camera  
aims at.  
5. Click the <RECORD> button.  
To activate the preset  
1. Click <  
> button to display “Preset” window.  
2. Select a desired preset to activate from the list.  
The camera’s framing moves to the preset position.  
To activate Swing, Group, Tour and Trace  
You can activate listed functions in the same manner as using a preset. For more information, refer to  
corresponding user manul of applicable camera.  
Only selective functions of the camera can be supported, depending on camera.  
M
96_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling OSD Menu  
If connected PTZ camera supports the OSD menu, press the <  
change its settings.  
> to enter camera’s menu screen to  
b
a
Part Names  
Direction Adjustment  
Functions  
You can go to a desired menu.  
Selects a desired item.  
a
b
ENTER  
Menu On/Off  
You can On/Off camera’s OSD menu settings.  
For more information about camera’s OSD menu, refer to corresponding user manul of each camera.  
M
English _97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
USING SEARCH VIEWER  
The Search Viewer screen consists of following :  
Up to 3 users can access simultaneously.  
k j  
a
b
c
d
e
i
f
g
h
Menu  
Menu Selection  
Functions  
Switches to the corresponding menu screen by clicking each menu.  
a
b
c
Address, Name, Time  
Split Mode Selection  
Displays the IP, model name, time, etc. of connected DVR.  
Selects the type of split screen and selects the channel displayed in Display Pane.  
CAPTURE  
Saves current video for selected channel in designated path.  
Prints current video image for selected channel through designated printer.  
PRINT  
Records the live video in AVI file format in designated path, and then stops recording.  
AVI Save  
d
Recording status icon is displayed on screen during recording.  
Audio  
OSD  
Calendar  
Sets the sound connected to each channel to ON/OFF.  
Select the format of OSD information that will be displayed.  
Displays the video-recorded date in blue and today in white. Click the date in blue color  
e
f
to display the recorded video information in timeline.  
Displays and zooms in/out recorded video data. If overlapping data found, this function  
selects one of them to play.  
Overlapped Data  
98_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Play Control  
Functions  
Adjusts current video’s playback speed and played time position.  
g
h
Displays the corresponding color depending on recorded data type if you place your  
mouse cursor on that area.  
Recording Color  
Display Pane  
Logout  
User ID  
Plays corresponding data on the screen if you select a search result.  
Click Logout icon for logout.  
i
j
k
Displays the user's ID.  
Searching the Recorded Video in the Calendar  
Dates having recorded video are marked in blue.  
Click a date marked blue to display video information on the  
timeline. When you click <  
>, it will be synchronized  
with the system time (date) of the current PC.  
To search by date  
You can select the search date by using calendar.  
1. Click <  
> or <  
> or <  
> to select the year to search.  
> to select the month to search.  
2. Click <  
The date including data appears in blue and today  
appears in red.  
3. Click the date to search in calendar.  
The first image of searched video data on the date is displayed on screen and the data is displayed in the  
timeline.  
4. To search video data on today, click <  
>.  
Today’s date is selected.  
(PC Time)  
To adjust timeline  
If searched data are overlapping, you can select a desired data, move its playback time point, and zoom in/  
out the timeline.  
1. Select the number of data to search if data is overlapping.  
It appears only when data are overlapped and assigns <0> to the most recent data.  
2. Click your desired time point to play on the timeline.  
The playback start point is moved.  
3. Click <  
>, <  
> to zoom in/out the zoom factor to display time.  
4. To show the previous/next timeline in zoomed-in status, click <  
> or <  
> to go to the left or right.  
English _99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Names and Functions of Play Buttons  
a Moves backward by 10 minutes from the current playing  
a b c d  
e f  
point.  
b Plays in reverse at doubled speed. The playback speed is  
doubled up to 64x speed.  
c Moves backward by 1 second from current playing point.  
g h i j  
k l  
d Moves forward by 1 second from current playing point.  
e
Plays at doubled speed. The playback speed is doubled up to 64x speed.  
f Moves forward by 10 minutes from the current playing point.  
g Moves to the recording start point on the corresponding timeline.  
h Plays in reverse.  
i Stops playing. When resuming playback, it is played from the recording start point.  
j Pauses playing. When resuming playback, it is played from the stopped point.  
k Plays normally.  
l Moves to the recording end point on the corresponding timeline.  
100_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIEWER SETUP  
You can configure the DVR settings remotely on the network.  
To configure the DVR settings, click <Setup>.  
System  
YDoautcean/Tcoimnfigeu/rLeathnegvauriaougsesettings of the DVR system.  
For more information, refer to <Date/Time/Language> in the <System Setup> menu. (Page 38)  
1. Select <Date/Time/Language> in the System menu.  
2. Configure the DVR settings according to your system environment.  
• Date/Time  
Set the date and time.  
• Time Synchronization Setup  
Set the time synchronization.  
• Display  
Date Format : Set the date type.  
Time : Select a time format to display on the screen.  
• DST (Daylight Saving Time)  
DST is displayed an hour ahead of the standard time of the time zone.  
• Language  
Select a preferred language for the DVR.  
English _101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Holiday  
You can set specific dates to Holidays according to your preferences.  
For more information, refer to <Setting Holiday> in the <System  
Setup> menu. (Page 39)  
Permission Management  
For more information, refer to <Permission Management> in the <System Setup> menu. (Page 40)  
• Admin  
You can change the admin ID or the password.  
You can type the ID with alphanumeric characters only.  
For the password, use alphabets and special characters excluding <\> and  
<">.  
• Group  
Users are classified into groups and the permission can be  
set according to the group.  
First of all, add a group.  
102_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• User  
You can add, change or remove a user or users.  
• Setup  
You can set the user permission.  
System Management  
For more information, refer to <System Management> in the <System Setup> menu. (Page 44)  
• System Information  
You can see information of the current system.  
V1.0xh_yymmddhhmmss  
Check the Software Version, Broadcast Format and MAC Address.  
English _103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Device  
You can check a list of devices that are connected to the DVR and configure the necessary settings.  
Click <Device> in the menu screen.  
FCoar mmoererianformation, refer to “Setting the Device”. (Page 48)  
• Camera  
You can configure the settings of the camera that is connected to the  
DVR.  
• Privacy Region  
You can specify a certain area of the camera video to be protected for  
your privacy.  
• PTZ  
You can configure the settings of the PTZ camera that is connected to  
the DVR.  
Set the ID and protocol.  
104_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Storage Device  
You can check and change the settings of the storage device.  
• Device  
You will see a list of storage devices that are connected to the DVR.  
You can check the type, used/total, usage and status of the device.  
• HDD Alarm  
You can set the alarm output channel and the alarm duration for an  
error.  
Remote Device  
You can see a list of remote devices including PTZ cameras and  
system keyboards that are connected to the RS-485 port of the DVR  
and configure the necessary settings.  
English _105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
POS Device  
You can set the channel, preset and communication port of the POS  
device that is connected to the DVR.  
You cannot set to use the POS device remotely.  
M
Monitor  
• Monitor  
You can configure the monitoring screen settings and set the output  
system.  
• Mode  
You can switch between live mode and play mode.  
106_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Record  
FRoer mcoorredinifnorgmaSticonh, eredfeur tloe<Setting the Recording>. (Page 58)  
If you set a recording schedule for a specific date and time, the  
recording will start at that specific time.  
- Apply to All CH : Click <Apply to All CH> to display the  
confirmation window.  
Event Record Duration  
You can set the start and end times of recording that will be activated  
if an event occurs.  
English _107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
REC Quality & Resolution  
• Standard/Event  
You can set the resolution, frame rate and recording quality for each  
channel.  
Record Option  
You can set the Disk End Mode.  
Event  
For more information, refer to <Setting the Event>. (Page 61)  
Sensor Detection  
You can set the sensor operation mode and the synchronized camera  
as well as the alarm output type and the duration.  
108_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motion Detection  
You can set the motion detection mode and the sensitivity  
as well as the alarm output type and the duration.  
• Motion Region  
Set the target motion detection area.  
Video Loss Detection  
You can set the alarm output time if a video loss occurs.  
Tampering Detection  
You can set whether to generate alarm and its dwell time for video  
tampering events.  
English _109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Alarm Schedule  
You can schedule the alarm output according to the day of the week  
and the time.  
The default setting is Event Sync, which activates the alarm only if an  
event occurs.  
Network  
FCoor mnonreecinftoiromnatiMono, rdefeer to <Network Configuration>. (Page 66)  
A remote user can access the DVR via the network to check the current mode and the IP address.  
• Interface  
You can set the network connection route.  
• Port  
You can configure the protocol related settings.  
110_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Alarm  
Set the alarm.  
DDNS  
You can check the DDNS settings.  
Live Transfer  
Sets the quality of the image that is transferred from the DVR to the network.  
• Live Transfer  
A remote user can set the image resolution of the transferred data.  
English _111  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
Mailing Service  
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.  
• SMTP  
You can set the server that sends mails and specify if you use the  
authentication process.  
• Event  
You can set the event interval and specify which events the server  
sends mails for.  
• Group  
You can add a group to receive the mail if an event occurs and set the  
permission to receive the event mail for each group.  
112_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Recipient  
You can add a user or users who will receive the mail.  
SNMP  
You can configure the settings for the SNMP protocol.  
ABOUT  
Click <About>.  
Displays the model name of connected DVR and the version of Web Viewer.  
English _113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
CONNECTING WEB VIEWER (Mac)  
Safari on MAC.  
If you want to use SRD-Series DVR Web Viewer with Safari Browser on a Mac, please refer to this user guide  
and install Multi Viewer with firmware upgrade if necessary.  
• Mac OS versions available : 10.6 or later version  
• Silverlight : 5 or later  
• Safari : 5 or later  
1. Click [Click now to Install] to display the installation  
screen as shown.  
2. Double-click the [Silverlight.pkg] icon to display the  
Silverlight plug-in installation screen as shown.  
3. Click [Continue] to start installing Silverlight plug-in.  
When done, you will see the screen as below.  
4. Click [Close] to exit from the Silverlight plug-in installation  
screen.  
114_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• If Microsoft Silverlight plug-in is already installed  
1. Use a web browser to connect to the DVR.  
2. If Silverlight plug-in is already installed, you will see the  
login screen as shown.  
3. If the login screen does not appear, check if the DVR set is  
connected properly with a valid IP address.  
If automatic proxy is activated and an invalid DNS server is specified while configuring network, the Internet access  
M
may not be available.  
For more details on using the Web Viewer, please refer to “Connecting Web Viewer (Windows)”. (Page 88)  
• If Safari 6.1 or higher is used, set it as shown below.  
1. Select Safari "Preferences > Security > Internet Plugin".  
2. Click on silver light plugin.  
3. Set the DVR address to "Allow Always" or "Run in  
Unsafe Mode".  
4. When the program has finished installing, open the web  
viewer again to login.  
When installation is finished, and you are successfully  
logged in, the live viewer main screen will appear.  
English _115  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
USING LIVE VIEWER (Mac)  
The Live Viewer screen consists of following :  
b
a
c
d
e
f
g
h
i
j
k
Menu  
Name, Address  
Menu Selection  
Functions  
Displays a connected DVR’s IP address and model name.  
a
b
Live  
About  
LOGOUT  
Consists of <  
> ,<  
> and <  
> menu.  
These buttons are used for the screen split and full screen mode.  
Split Mode Selection  
c
Supports up to a maximum of 9 channels due to performance constraints of Silverlight.  
Name, Address  
Audio  
Displays a connected DVR’s IP address and model name.  
Sets the sound connected to each channel to ON/OFF.  
d
e
DVR Time  
PC Time  
Select <  
> or <  
> for the OSD time information display setting of the Live  
DVR Tim, PC Time  
f
g
Viewer.  
Switches into previous/next channel or perform Auto Sequence.  
Change Channel  
Click Auto Sequence button to display the Time Interval Selection menu.  
CAPTURE  
PRINT  
Saves current video for selected channel in designated path.  
Prints current video image for selected channel through designated printer.  
h
Starts and stops recording.  
RECORD  
If you cannot play the file recorded from the web, please install the H.264 CODEC.  
ex) MAC: perian_1.2.3.dmg (http://perian.org)  
116_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Functions  
Channel  
PTZ  
Indicates connected DVR's channels.  
Controls connect PTZ camera(s).  
i
j
k
Display Pane  
Displays the video of camera connected to DVR.  
MOBILE VIEWER  
What is Mobile Viewer?  
Mobile Viewer is management software that enables you to connect  
to DVR (Digital Video Recorder) remotely and control the video  
playback and PTZ operations (if configured) in real time.  
Key Features  
• Remote access via Smart phone  
• Voice Recognition  
• 1-split and 4-split modes supported in Live Viewer  
• Supports single channel search function  
• Switch channels using the touch-sensitive LCD panel  
• PTZ camera operations supported  
(complies with the protocol of the connected DVR)  
• Up to 16 channels supported  
2.X  
20xx. xx. xx  
Compatible Smartphone  
This application is optimized for  
• iOS v6.1, v7.0 (iPhone 4/5, iPad 2/3/4)  
• Android OS v4.1, v4.3 (Galaxy S2/S3/S4, Galaxy Note)  
For more information, refer to the user manual.  
(http://www.samsungcctv.com)  
M
English _117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
backup viewer  
SEC BACKUP VIEWER  
You can play a file that is backed up in the format of SEC.  
Backup in SEC format produces backup data file, library file and self-executable viewer file.  
If you run the backup file viewer, the backup data file will be automatically played.  
a
b
c
d e f  
SRD-1656D_CAM 01  
2014-01-01 06:59:57  
CAM 01  
2014-001-011 06:59:57  
j
i
hg  
Recommended System Requirements  
PCs with a lower specification than the recommended below may not fully support forward/backward and  
high-speed playback.  
• OS : Windows XP professional, Windows Vista, Windows 7  
• CPU : Intel i5 2.8GHz or faster  
• RAM : DDR PC-3200 1G or more  
• VGA : Geforce 6200 or higher  
118_ backup viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names  
Functions  
Set the screen’s aspect ratio to be displayed.  
Split Screen  
a
b
c
The screen switches to the selected split screen mode.  
Split screen function is not supported during the CD/DVD backup.  
Saves the current video’s image as in an image file. Supports jpeg file format.  
Screen Printout  
Audio  
Prints out the current screen. You should have installed the appropriate printer  
driver before you can print out the screen.  
A toggle button. Each time you press this button, the audio output will toggle  
between activated and deactivated.  
/
/
You can adjust the volume level from 0 to 100.  
Watermark  
Deinterlace  
Press the button to enable file tampering detection, to detect data file forging.  
You can enable the De-interlace function.  
d
e
Check the OSD checkbox to display the OSD information on the backup  
playback screen.  
Show OSD  
f
Information such as backup date, day of the week, time, model name, and  
channel number will be displayed on the screen.  
Collapses the time range that is displayed on the range bar of the storage  
time. You can collapse the range bar until the overall range is shortened to  
24 hours.  
Enlarges the time range that is displayed on the range bar of the storage  
time. You can enlarge the range bar until the overall range is extended to  
1 minute.  
Enlarge /  
g
Reduce Timeline  
Restore Timeline  
Restores the timeline to the default.  
h
i
Displays the time range of a stored video file.  
Display of storage time range  
You can move the gridline of the range bar to select a time point to play.  
Playback Control  
You can adjust the video playback of the timeline.  
j
If it has a high recording rate and is played at high speed playback of 16x or higher speed in the backup viewer,  
actual playback speed may not reach the set playback speed.  
M
English _119  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
PRODUCT SPECIFICATION  
Details  
Item  
SRD-876D  
SRD-1656D  
SRD-1676D  
16(8) composite video 0.5–1 Vpp, 75 ohm automatic termination  
1280x480 NTSC, 1280x576 PAL / 720x480 NTSC, 720x576 PAL  
240fps NTSC, 200fps PAL 480fps NTSC, 400fps PAL  
1280x480 NTSC, 1280x576 PAL  
Inputs  
Video  
Resolution  
Frame rate  
Live  
Resolution  
1/4/6/8/Sequence/PIP  
1/4/7/9/13/16/16A/PIP/Sequence  
Multi Screen display  
Performance  
Operating System  
Linux  
H.264  
Embedded  
Compression  
SRD-876D  
NTSC: Up to 240fps @ 1280x480 / PAL: Up to 200fps @ 1280x576  
NTSC: Up to 240fps @ 704x480 / PAL: Up to 200fps @ 704x576  
NTSC: Up to 240fps @ 704x240 / PAL: Up to 200fps @ 704x288  
NTSC: Up to 240fps @ 352x240 / PAL: Up to 200fps @ 352x288  
SRD-1656D  
NTSC: Up to 120fps @ 1280x480 / PAL: Up to 100fps @ 1280x576  
NTSC: Up to 120fps @ 704x480 / PAL: Up to 100fps @ 704x576  
NTSC: Up to 240fps @ 704x240 / PAL: Up to 200fps @ 704x288  
NTSC: Up to 480fps @ 352x240 / PAL: Up to 400fps @ 352x288  
Record Rate  
SRD-1676D  
NTSC: Up to 480fps @ 1280x480 / PAL: Up to 400fps @ 1280x576  
NTSC: Up to 480fps @ 704x480 / PAL: Up to 400fps @ 704x576  
NTSC: Up to 480fps @ 704x240 / PAL: Up to 400fps @ 704x288  
NTSC: Up to 480fps @ 352x240 / PAL: Up to 400fps @ 352x288  
Recording  
NTSC: Manual, Schedule (Continuous/Event), Event(Pre/Post), Time lapse (1~30 fps)  
PAL: Manual, Schedule (Continuous/Event), Event(Pre/Post), Time lapse (1~25 fps)  
Video Loss, Motion(Level 1~10), Alarm, Tampering(Level 1~3)  
Selectable (Stop/Continuous)  
Up to 30 sec (5, 10, 20, 30 Sec)  
Up to 6 hour (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min, 1, 2, 3, 4, 5, 6 hour)  
Date/time, Event, Back up, POS, Motion (※ All Search Included Prview Function)  
Mode  
Event  
Overwrite modes  
Pre-alarm  
Post-Alarm  
Search mode  
Fast Forward/Backward (x2,x4,x8,x16,x32,x64)  
※
Backward Play with I-frame Only,  
Search & Playback  
Slow Forward/Backward (x1/2,x1/4,x1/8)  
Playback function  
※
Backward Play with I-frame Only  
Step Forward/Backward  
Skip Forward/Backward  
120_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Details  
Item  
SRD-876D  
SRD-1656D  
SRD-1676D  
Option 1) 1280H/4CIF/  
2CIF/CIF(120/120/240/  
480fps NTSC, 100/100/  
200/400fps PAL)  
Option 1) 1280H/4CIF/  
2CIF/CIF(240fps NTSC,  
200fps PAL)  
Option 1) 1280H/4CIF/  
2CIF/CIF(480fps NTSC,  
400fps PAL)  
Transmission speed  
Option 2) 4CIF/2CIF/  
CIF(120/240/240fps NTSC,  
100/200/200fps PAL)  
Option 2) 4CIF/2CIF/  
CIF(120/240/480fps NTSC,  
100/200/400fps PAL)  
Option 2) 4CIF/2CIF/  
CIF(120/240/480fps NTSC,  
100/200/400fps PAL)  
Bandwidth  
Up to 32Mbps  
Selectable  
H.264(4CIF/2CIF/CIF Selectable)  
Network (IPv4)  
Bandwidth control  
Stream  
Remote users  
Search(3)/Live Unicast(10)/Live Multicast(20)  
Maximum  
Protocol support  
Monitoring  
TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP, SNMP  
Smart viewer,Web viewer, SSM(CMS)  
Android, iOS  
Platform  
Protocol support  
RTP, RTSP, HTTP, CGI, HTTPS  
Smart phone  
Storage  
Remote users  
Live(4), Search(1)  
Maximum  
Internal HDD  
External HDD  
Up to 4 SATA HDDs  
Up to 2 expansion bay (※ Model: SVS-5R/5E)  
DVD Writer  
YES  
(Back-up)  
USB (Back-up)  
2 USB Ports  
File Format  
BU(DVR Player), EXE(Include Player), AVI  
(Back-up)  
Password Protection 1 Admin, 10 Group , 10 User per 1 Group  
Security  
Interface  
Data Authentication Watermark  
VGA  
1 VGA (1280x720, 1280x1024, 1920x1080)  
1 HDMI (1280x720, 1280x1024, 1920x1080)  
-
Digital Spot (2CH)  
8CH  
16CH(8CH) line in (Built in 4CH, Option : Audio Extension Cable)/ 1CH line out  
G.711  
8KHz  
HDMI  
Monitors  
Audio  
Main Composite  
Spot(Composite)  
Loop Outputs  
Inputs / Output  
Compression  
Sampling rate  
※
Included OSD On Screen, Multi mode Support(CH1)  
16CH  
English _121  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Details  
Item  
SRD-876D  
SRD-1656D  
SRD-1676D  
Terminal 16(8) Inputs (NO/NC) / Terminal 4 relay Outputs (NO/NC),  
Inputs / Output  
Alarm  
Rating : 30V DC/2A, 250V AC/0.25A  
Notification via e-mail  
Remote notification  
Ethernet  
1 RJ45 10/100/1000 Base-T  
RS-232/RS-485(Full Duplex) for PTZ, Samsung System Keyboard  
USB 2.0, 2 ports  
Serial interface  
USB  
e-SATA  
2 External SATA ports  
Connections  
Application Supoort Mouse, Remote Controller  
Samsung-E/Samsung-T/Pelco-D/Pelco-p/Panasonic/Phillips/AD/DIAMOND/ERNA/  
KALATEL/VCL TP/VICON/ELMO/GE  
Protocol support  
PTZ Control via Coaxial Cable (Samsung CCVC, Pelco-C (Coaxitron)) Max. Transfer  
Length 200M(5C2V Cable)  
General  
Input Voltage / Current 100 to 240 VAC 10%; 50/60 Hz, Autoranging  
Power consumption Max. 60 W (with 1x HDD)  
Operating  
Electrical  
Environmental  
Temperature /  
Humidity  
+0°C to +40°C (+32°F to +104°F) / 20% to 85% RH  
W440 x H88 x 384.8 mm (17.32" x 3.46" x 15.15")  
Dimension (W x H x D)  
H (leg not included)  
Mechanical  
Lauguage  
Weight  
6.5 kg  
2 EA  
6.6 kg  
(With hard disks)  
Rack mount kit  
Korean, Japanese, Chinese (Simplified), English, French, German, Spanish, Italian,  
Russian, Polish, Czech, Turkish, Netherlands, Portuguese,Swedish, Danish,  
Thailandais, Rumania, Serbia, Croatia, Hungary, Greek, Chinese (Traditional),  
Finnish, Norwegian (25 Language)  
122_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT OVERVIEW  
• SRD-876D  
unit : mm(inch)  
English _123  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
• SRD-1656D/1676D  
unit : mm(inch)  
124_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DEFAULT SETTING  
This returns the factory default settings.  
The settings are made as follows;  
• Use System/Load Factory Default in MENU  
The default settings are based on SRD-1656D.  
The default administrator ID is “admin”, and the password must be set when the user log in at the first time.  
To prevent from your personal information being exposed, please change your password every 3 months. Note that the security and other  
related issues caused by careless management of password shall be be in the charge of the user.  
Category  
Details  
Factory Default  
Date  
Time Format  
Time Zone  
Time Synchronize  
DST  
YYYY-MM-DD  
24 hours  
GMT  
Date/Time/Language  
Date/Time/Language  
OFF  
OFF  
Language  
ID  
English  
admin  
Admin  
User  
Group  
All Group  
System Settings  
Backup/Record Lock/  
Search/PTZ/Remote  
Alarm Out/Shutdown  
Restricted Access  
Permission  
Management  
Auto Logout  
Manual Input of ID  
Touch Button Sound  
Touch Button  
Broadcast Format  
Video  
OFF  
Setting  
OFF  
ON  
ON  
System Management  
Camera  
System Information  
Camera  
NTSC/PAL  
ON  
OFF  
Audio  
CH Name  
CAM 01 ~ CAM 16  
SEQ-Dwell Time  
Progressive  
ID  
5 sec  
OFF  
Camera No.  
None  
42  
PTZ  
Protocol  
Device  
Brightness  
Screen Setup  
Contrast  
53  
Color  
50  
Check Alarm Output Port  
Duration  
OFF  
OFF  
Storage Device  
HDD Alarm  
Replace Alarm Output Port  
Duration  
OFF  
OFF  
English _125  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Category  
Details  
Factory Default  
Baudrate  
9600  
None  
8
Parity  
Data  
Stop bit  
Remote Device  
1
OFF  
System Keyboard  
Remote Control  
ON(00)  
OFF  
POS Device  
Event Display  
Display  
OFF  
All  
Multi CH SEQ Time  
VGA/HDMI  
5 sec  
1280X1024  
Device  
Monitor  
HDMI Resolution Auto  
ON  
Detection  
Screen mode  
Sharpness  
Multi Spot  
Spot Out 1  
Spot Out 2  
Event Display  
Live Screen  
Play Screen  
Clear screen  
Monitor  
Level3 (High)  
OFF  
SEQ  
Spot Out  
Mode  
SEQ  
OFF  
ALL  
ALL  
Recording Schedule  
CH1~CH16  
PRE Event  
POST Event  
Both(Cont&Evnt)  
OFF  
Event Record Duration  
1 min  
Resolution  
CIF  
NTSC: 7fps  
Normal Recording  
Event  
Frame Rate  
PAL: 5fps  
Record Quality  
Resolution  
Level 4  
4CIF  
Recording  
REC Quality/Resolution  
Record Option  
NTSC: 7fps  
Frame Rate  
PAL: 5fps  
Record Quality  
Setup  
Disk End Beep  
Level 4  
Overwrite  
OFF  
Disk End Mode  
Auto Delete  
OFF  
126_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Category  
Details  
Factory Default  
Sensor Operation  
Camera  
OFF  
Camera No.  
None  
Sensor Detection  
Alarm  
Duration  
Mode  
10 sec  
OFF  
Level10(high)  
None  
Sensitivity  
Alarm  
Motion Detection  
Duration  
Motion Region  
Video Loss State  
Alarm  
10 sec  
All Area  
OFF  
Event  
Video Loss Detection  
None  
Duration  
Mode  
10 sec  
OFF  
Medium  
None  
10 sec  
Event Sync  
Sensitivity  
Alarm  
Duration  
Alarm1  
Tampering Detection  
Alarm Schedule  
English _127  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Category  
Details  
Factory Default  
IP Type  
Transfer Bandwidth  
IP Address  
Static  
2Mbps  
192.168.1.200  
192.168.1.1  
255.255.255.0  
168.126.63.1  
TCP  
Interface  
Gateway  
Subnet Mask  
DNS  
Connection Mode  
Protocol Type  
Device Port  
4520~4524  
80  
Port  
HTTP Port  
Secure Video Transmission  
Disconnect Alarm Output Port  
Duration  
OFF  
OFF  
Alarm  
OFF  
DDNS  
DDNS Site  
Resolution  
Quality  
OFF  
Network  
CIF  
Live Transfer  
Low  
Server  
Port  
OFF  
25  
SMTP  
Use Authentication  
Secure Transfer  
Event Interval  
OFF  
Never  
10 min  
Mailing Service  
SNMP  
The number of attached  
Event  
1
images for each event  
Use Event Transfer  
Group  
OFF  
OFF  
OFF  
OFF  
OFF  
Group  
Recipient Permission  
Enable SNMP v1  
Enable SNMP v2c  
128_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Symptom  
Countermeasures  
The system does not turn on and the indicator on the Check if the power supply system is properly connected.  
front panel does not work at all.  
Check the system for the input voltage from the power source.  
If the problem persists even after you have taken the above actions,  
check the power supplier and replace it with a new one if neccessary.  
Some channels display just a black screen even if  
they receive video sources.  
Check if the camera connected to the system properly displays the  
image. Sometimes, this problem may occur on a camera that is not  
properly connected to the video source.  
Check if the camera is properly supplied with power.  
Sometimes, this problem may occur on a channel with weak video  
signal from a video distributor that is connected to multiple systems. In  
this case, input the video source of the camera directly into the DVR.  
This may find the cause and solve the problem.  
If I press the [REC] button on the front panel, the  
REC indicator does not flash, nor the player start  
recording.  
Check if there is a free space on the HDD for the recording.  
Check if the record mode is set to ON in the record mode setting.  
The screen displays the logo image repeatedly.  
This may occur from a problem with the main board, or the related  
software is corrupt.  
Contact the nearest service center for more information.  
The Channel button does not work on the Live  
screen.  
The Channel button does not work if the current screen is in the event  
monitoring mode.  
In the event monitoring screen, press the [ALARM] button to exit the  
screen and select a channel.  
The cursor will not move to the Start button when I  
start the calendar search.  
Check if the channel and the date that you want to play are marked  
with the V symbol.  
Both channel and date should be checked before you can start playing  
with the Start button.  
When the alarm sounds, I press the [ALARM] button  
on the front panel to release the alarm but it does  
not work. The alarm persists and I could not set it off  
in any way.  
Press the [MENU] button on the front panel to release the alarm in the  
following way:  
1) To release the event monitoring mode : Monitoring Mode – set the  
duration of the event monitoring to Off.  
2) To release the alarm sound : Event Record Mode - Alarm (Motion  
Detection/Video Loss/Tampering Detection) – deactivate the alarm  
sound.  
3) To release the event : Event Record Mode - Alarm (Motion Detection/  
Video Loss/Tampering Detection) – set the mode to Off.  
No response is made even if I press the [PTZ] button Menu ¨ Camera ¨ Check if the current protocols and other settings  
on the Live screen.  
in the PTZ device are properly configured according to the PTZ camera.  
English _129  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Symptom  
Countermeasures  
It takes time for the DVR to recognize multiple external HDDs. Try again  
in a moment and if the problem (of failure to recognize as many HDDs  
as connected) persists, it may occur due to a mechanical error of the  
HDD installed. Try again with a different HDD.  
I've found that the DVR does not recognize as many  
disks as installed when I have connected multiple  
external HDDs to the DVR.  
A message of “Need to reset date/time.” Is displayed This message is displayed if there occurs a problem with the time  
on the screen.  
setting of the internal clock or an error in the clock itself.  
Contact the retailer or the service center for more information.  
The time bar is not displayed in Search mode.  
The timeline can switch between normal and extension mode.  
In extension mode, the time bar may not be displayed in the current  
timeline. Switch to normal mode or use the left or right button to  
navigate through the time bar.  
The “NO HDD” icon and an error message are  
displayed.  
Check the HDD for connection. If the problem persists in a normal  
condition, contact the nearest service center to have the HDD checked  
by the service personnel.  
I have installed an additional HDD on the DVR but it  
does not recognize the HDD.  
See the compatibilty list to check if the additional HDD is supported by  
the DVR. For the compatibility list, contact the retailer where you  
purchased the DVR.  
I have connected an external storage device (external See the compatibility list of external storage devices to check if the  
SATA HDD) to the DVR but the DVR seems not to  
recognize it.  
connected device is supported by the DVR.  
For the compatibility list, contact the retailer where you purchased the  
DVR.  
If I press the ESC key in full screen mode of the  
WebViewer, the system does not switch to a normal  
split mode.  
Press the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC  
key again. The system will switch to a normal split mode.  
I found it difficult to configure the network settings if  
For more information, refer to the user manual.  
using the default search, backup and router settings. If you want to check the basics of the product for a quick start, refer to  
the quick start guide (backup, search).  
If you use the router for network connection, refer to the “Connecting  
to the Internet using the router” section in this manual.  
I forgot the password.  
Contact the DVR administrator for help.  
Backup data is just not played by the PC or DVR.  
When you are backing up data, you have choices about the player  
either: PC or DVR. Make your selection before proceeding.  
If you are using the PC to play the data, the format of the backup file  
should be either SEC.  
If you are using the DVR for this purpose, formatting backup files should  
be done by the DVR.  
My player does not switch to Live mode while in  
playback.  
Press the Stop [@] button on the DVR or the remote control, or click the  
[
] icon on the launcher to switch to Live mode.  
130_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Symptom  
Recording does not work.  
Countermeasures  
If your player does not display a Live image at all, that indicates  
recording does not work so first check if you see an image on the  
screen.  
Recording does not work if the recording settings are not properly  
configured.  
1) Manual Record: Press the [REC] button on the front panel of the DVR  
or on the remote control to start recording.  
2) Scheduled Record: Specify a desired time in Menu – Record –  
Recording Schedule. Recording will start at the specified time.  
- <Continuous> Record: Recording will proceed in any conditions  
at the specified time.  
- <Event> Record: When an event occurs, recording will perform  
only if the event is of alarm, motion detection, video loss and  
Tampering Detection.  
If there is no event found, recording will not perform.  
- <Continuous / Event> Record: If there is no event found,  
Continuous recording will perform. Whereas, if an event occurs,  
Event recording will perform.  
The image quality of the recording data is not good.  
Increase the resolution and quality level in Menu – Record – Quality /  
Resolution.  
1) Resolution: Select a bigger size when specifying the recording size.  
(1280H>WD1>4CIF>2CIF>CIF)  
The recording image in the CIF format shows a deteriorated quality  
as it is enlarged from a small-sized image.  
2) Record Quality: Specify a bigger level for the recording quality.  
If you increase the resolution and the recording quality, the data size  
increases accordingly. So the HDD will be filled faster. Overwriting will  
overwrite the existing data so recording will proceed at a shorter  
interval.  
English _131  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPEN SOURCE ANNOUNCEMENT  
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete  
Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to [email protected]  
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source  
distribution might be charged.  
• GPL Software : linux kernel, Sysvinit, dosfstools, wget, msmtp, busybox, cdrtools, dvd+rw-tools, iconv, smartctl, uboot, minicom, openssl, bash,  
lm_sensors, parted, procps, util-linux 2.19.1, xfsprogs 3.1.7  
• LGPL Software : glibc, vmstat, inetutils, calendarview.js, libiconv  
• OpenSSL License : OpenSSL  
• Boost Software License: Boost-1.43.0 (http://www.boost.org/)  
• COMMON DEVELOPMENT AND DISTRIBUTION LICENSE: cdrtools 2.01.01  
• FreeType Project LICENSE: freetype2  
• RSA MD4 or MD5 Message-Digest Algorithm License : MD5 Message Digest Code  
• MIT License : JQuery, Prototype JavaScript framework, FJCore  
Activities other than copying, distribution and modification are not  
GNU GENERAL PUBLIC LICENSE  
covered by this License; they are outside its scope. The act of running  
the Program is not restricted, and the output from the Program is  
covered only if its contents constitute a work based on the Program  
(independent of having been made by running the Program). Whether  
that is true depends on what the Program does.  
Version 2, June 1991  
Copyright (C) 1989, 1991 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA  
Everyone is permitted to copy and distribute verbatim copies of this  
1. You may copy and distribute verbatim copies of the Program’s  
source code as you receive it, in any medium, provided that you  
conspicuously and appropriately publish on each copy an appropriate  
copyright notice and disclaimer of warranty; keep intact all the notices  
that refer to this License and to the absence of any warranty; and give  
any other recipients of the Program a copy of this License along with  
the Program.  
lPicreensaemdobcluement, but changing it is not allowed.  
The licenses for most software are designed to take away your freedom  
to share and change it. By contrast, the GNU General Public License is  
intended to guarantee your freedom to share and change free software  
to make sure the software is free for all its users. This General Public  
License applies to most of the Free Software Foundation’s software and  
to any other program whose authors commit to using it. (Some other  
Free Software Foundation software is covered by the GNU Lesser  
General Public License instead.) You can apply it to your programs, too.  
You may charge a fee for the physical act of transferring a copy, and  
you may at your option offer warranty protection in exchange for a fee.  
2. You may modify your copy or copies of the Program or any portion of  
it, thus forming a work based on the Program, and copy and distribute  
such modifications or work under the terms of Section 1 above,  
provided that you also meet all of these conditions:  
When we speak of free software, we are referring to freedom, not price.  
Our General Public Licenses are designed to make sure that you have  
the freedom to distribute copies of free software (and charge for this  
service if you wish), that you receive source code or can get it if you  
want it, that you can change the software or use pieces of it in new free  
programs; and that you know you can do these things.  
a) You must cause the modified files to carry prominent notices  
stating that you changed the files and the date of any change.  
b) You must cause any work that you distribute or publish, that in  
whole or in part contains or is derived from the Program or any  
part thereof, to be licensed as a whole at no charge to all third  
parties under the terms of this License.  
To protect your rights, we need to make restrictions that forbid anyone  
to deny you these rights or to ask you to surrender the rights. These  
restrictions translate to certain responsibilities for you if you distribute  
copies of the software, or if you modify it.  
c) If the modified program normally reads commands interactively  
when run, you must cause it, when started running for such  
interactive use in the most ordinary way, to print or display an  
announcement including an appropriate copyright notice and a  
notice that there is no warranty (or else, saying that you provide a  
warranty) and that users may redistribute the program under these  
conditions, and telling the user how to view a copy of this License.  
(Exception: if the Program itself is interactive but does not normally  
print such an announcement, your work based on the Program is  
not required to print an announcement.)  
For example, if you distribute copies of such a program, whether gratis  
or for a fee, you must give the recipients all the rights that you have. You  
must make sure that they, too, receive or can get the source code. And  
you must show them these terms so they know their rights.  
We protect your rights with two steps:  
(1) copyright the software, and (2) offer you this license which gives you  
legal permission to copy, distribute and/or modify the software.  
Also, for each author’s protection and ours, we want to make certain  
that everyone understands that there is no warranty for this free  
software. If the software is modified by someone else and passed on,  
we want its recipients to know that what they have is not the original, so  
that any problems introduced by others will not reflect on the original  
authors’ reputations.  
These requirements apply to the modified work as a whole. If identifiable  
sections of that work are not derived from the Program, and can be  
reasonably considered independent and separate works in themselves,  
then this License, and its terms, do not apply to those sections when  
you distribute them as separate works. But when you distribute the  
same sections as part of a whole which is a work based on the  
Program, the distribution of the whole must be on the terms of this  
License, whose permissions for other licensees extend to the entire  
whole, and thus to each and every part regardless of who wrote it.  
Finally, any free program is threatened constantly by software patents.  
We wish to avoid the danger that redistributors of a free program will  
individually obtain patent licenses, in effect making the program  
proprietary. To prevent this, we have made it clear that any patent must  
be licensed for everyone’s free use or not licensed at all. The precise  
Thus, it is not the intent of this section to claim rights or contest your  
rights to work written entirely by you; rather, the intent is to exercise the  
right to control the distribution of derivative or collective works based on  
the Program.  
tTeErmRsManSd cAoNndDitioCnsOfoNr cDoIpTyIinOg,NdSistrFibOutRionCanOdPmYoIdNificGat,ion follow.  
In addition, mere aggregation of another work not based on the  
Program with the Program (or with a work based on the Program) on a  
volume of a storage or distribution medium does not bring the other  
work under the scope of this License.  
DISTRIBUTION AND MODIFICATION  
Version 2, June 1991  
Copyright (C) 1989, 1991 Free Software Foundation, Inc.  
51 Franklin S  
3. You may copy and distribute the Program (or a work based on it,  
under Section 2) in object code or executable form under the terms of  
Sections 1 and 2 above provided that you also do one of the following:  
0. This License applies to any program or other work which contains a  
notice placed by the copyright holder saying it may be distributed under  
the terms of this General Public License. The “Program”, below, refers  
to any such program or work, and a “work based on the Program”  
means either the Program or any derivative work under copyright law:  
that is to say, a work containing the Program or a portion of it, either  
verbatim or with modifications and/or translated into another language.  
(Hereinafter, translation is included without limitation in the term  
“modification”.) Each licensee is addressed as “you”.  
a) Accompany it with the complete corresponding machine-readable  
source code, which must be distributed under the terms of  
Sections 1 and 2 above on a medium customarily used for  
software interchange; or,  
b) Accompany it with a written offer, valid for at least three years, to  
give any third party, for a charge no more than your cost of  
physically performing source distribution, a complete machine-  
readable copy of the corresponding source code, to be distributed  
under the terms of Sections 1 and 2 above on a medium  
customarily used for software interchange; or,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c) Accompany it with the information you received as to the offer to  
distribute corresponding source code. (This alternative is allowed  
only for noncommercial distribution and only if you received the  
program in object code or executable form with such an offer, in  
accord with Subsection b above.)  
Software Foundation.  
10. If you wish to incorporate parts of the Program into other free  
programs whose distribution conditions are different, write to the author  
to ask for permission. For software which is copyrighted by the Free  
Software Foundation, write to the Free Software Foundation; we  
sometimes make exceptions for this. Our decision will be guided by the  
two goals of preserving the free status of all derivatives of our free  
software and of promoting the sharing and reuse of software generally.  
The source code for a work means the preferred form of the work for  
making modifications to it. For an executable work, complete source  
code means all the source code for all modules it contains, plus any  
associated interface definition files, plus the scripts used to control  
compilation and installation of the executable. However, as a special  
exception, the source code distributed need not include anything that is  
normally distributed (in either source or binary form) with the major  
components (compiler, kernel, and so on) of the operating system on  
which the executable runs, unless that component itself accompanies  
the executable.  
NO WARRANTY  
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,  
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE  
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY  
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
If distribution of executable or object code is made by offering access to  
copy from a designated place, then offering equivalent access to copy  
the source code from the same place counts as distribution of the  
source code, even though third parties are not compelled to copy the  
source along with the object code.  
4. You may not copy, modify, sublicense, or distribute the Program  
except as expressly provided under this License. Any attempt otherwise  
to copy, modify, sublicense or distribute the Program is void, and will  
automatically terminate your rights under this License. However, parties  
who have received copies, or rights, from you under this License will not  
have their licenses terminated so long as such parties remain in full  
compliance.  
5. You are not required to accept this License, since you have not  
signed it. However, nothing else grants you permission to modify or  
distribute the Program or its derivative works. These actions are  
prohibited by law if you do not accept this License. Therefore, by  
modifying or distributing the Program (or any work based on the  
Program), you indicate your acceptance of this License to do so, and all  
its terms and conditions for copying, distributing or modifying the  
Program or works based on it.  
6. Each time you redistribute the Program (or any work based on the  
Program), the recipient automatically receives a license from the original  
licensor to copy, distribute or modify the Program subject to these  
terms and conditions. You may not impose any further restrictions on  
the recipients’ exercise of the rights granted herein. You are not  
responsible for enforcing compliance by third parties to this License.  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF  
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE  
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY  
SERVICING, REPAIR OR CORRECTION.  
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR  
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE  
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED  
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR  
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF  
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN  
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your New Programs  
If you develop a new program, and you want it to be of the greatest  
possible use to the public, the best way to achieve this is to make it free  
software which everyone can redistribute and change under these  
terms.  
7. If, as a consequence of a court judgment or allegation of patent  
infringement or for any other reason (not limited to patent issues),  
conditions are imposed on you (whether by court order, agreement or  
otherwise) that contradict the conditions of this License, they do not  
excuse you from the conditions of this License. If you cannot distribute  
so as to satisfy simultaneously your obligations under this License and  
any other pertinent obligations, then as a consequence you may not  
distribute the Program at all. For example, if a patent license would not  
permit royalty-free redistribution of the Program by all those who receive  
copies directly or indirectly through you, then the only way you could  
satisfy both it and this License would be to refrain entirely from  
distribution of the Program.  
To do so, attach the following notices to the program. It is safest to  
attach them to the start of each source file to most effectively convey  
the exclusion of warranty; and each file should have at least the  
“copyright” line and a pointer to where the full notice is found.  
one line to give the program’s name and an idea of what it does.  
Copyright (C) yyyy name of author  
This program is free software; you can redistribute it and/or modify it  
under the terms of the GNU General Public License as published by the  
Free Software Foundation; either version 2 of the License, or (at your  
option) any later version.  
If any portion of this section is held invalid or unenforceable under any  
particular circumstance, the balance of the section is intended to apply  
and the section as a whole is intended to apply in other circumstances.  
This program is distributed in the hope that it will be useful, but  
WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See  
the GNU General Public License for more details.  
It is not the purpose of this section to induce you to infringe any patents  
or other property right claims or to contest validity of any such claims;  
this section has the sole purpose of protecting the integrity of the free  
software distribution system, which is implemented by public license  
practices. Many people have made generous contributions to the wide  
range of software distributed through that system in reliance on  
consistent application of that system; it is up to the author/donor to  
decide if he or she is willing to distribute software through any other  
system and a licensee cannot impose that choice.  
You should have received a copy of the GNU General Public License  
along with this program; if not, write to the Free Software Foundation,  
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.  
Also add information on how to contact you by electronic and paper  
mail. If the program is interactive, make it output a short notice like this  
when it starts in an interactive mode:  
Gnomovision version 69, Copyright (C) year name of author  
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details  
type ‘show w’. This is free software, and you are welcome to  
redistribute it under certain conditions; type ‘show c’ for details.  
This section is intended to make thoroughly clear what is believed to be  
a consequence of the rest of this License.  
8. If the distribution and/or use of the Program is restricted in certain  
countries either by patents or by copyrighted interfaces, the original  
copyright holder who places the Program under this License may add  
an explicit geographical distribution limitation excluding those countries,  
so that distribution is permitted only in or among countries not thus  
excluded. In such case, this License incorporates the limitation as if  
written in the body of this License.  
The hypothetical commands ‘show w’ and ‘show c’ should show the  
appropriate parts of the General Public License. Of course, the  
commands you use may be called something other than ‘show w’ and  
‘show c’; they could even be mouse-clicks or menu items--whatever  
suits your program.  
You should also get your employer (if you work as a programmer) or  
your school, if any, to sign a “copyright disclaimer” for the program, if  
necessary. Here is a sample; alter the names:  
9. The Free Software Foundation may publish revised and/or new  
versions of the General Public License from time to time. Such new  
versions will be similar in spirit to the present version, but may differ in  
detail to address new problems or concerns.  
Yoyodyne, Inc., hereby disclaims all copyright interest in the program  
‘Gnomovision’ (which makes passes at compilers) written by James  
Hacker.  
Each version is given a distinguishing version number. If the Program  
specifies a version number of this License which applies to it and “any  
later version”, you have the option of following the terms and conditions  
either of that version or of any later version published by the Free  
Software Foundation. If the Program does not specify a version number  
of this License, you may choose any version ever published by the Free  
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This  
General Public License does not permit incorporating your program into  
proprietary programs. If your program is a subroutine library, you may  
consider it more useful to permit linking proprietary applications with the  
library. If this is what you want to do, use the GNU Lesser General  
Public License instead of this License.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
a computer network, with no transfer of a copy, is not conveying.  
GNU GENERAL PUBLIC LICENSE  
An interactive user interface displays “Appropriate Legal Notices” to the  
extent that it includes a convenient and prominently visible feature that  
(1) displays an appropriate copyright notice, and (2) tells the user that  
there is no warranty for the work (except to the extent that warranties  
are provided), that licensees may convey the work under this License,  
and how to view a copy of this License. If the interface presents a list of  
user commands or options, such as a menu, a prominent item in the list  
meets this criterion.  
Version 3, 29 June 2007  
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>  
Everyone is permitted to copy and distribute verbatim copies of this license  
document, but changing it is not allowed.  
Preamble  
The GNU General Public License is a free, copyleft license for software  
and other kinds of works.  
1. Source Code.  
The “source code” for a work means the preferred form of the work for  
making modifications to it. “Object code” means any non-source form  
of a work.  
The licenses for most software and other practical works are designed  
to take away your freedom to share and change the works. By contrast,  
the GNU General Public License is intended to guarantee your freedom  
to share and change all versions of a program--to make sure it remains  
free software for all its users. We, the Free Software Foundation, use the  
GNU General Public License for most of our software; it applies also to  
any other work released this way by its authors. You can apply it to your  
programs, too.  
A “Standard Interface” means an interface that either is an official  
standard defined by a recognized standards body, or, in the case of  
interfaces specified for a particular programming language, one that is  
widely used among developers working in that language.  
The “System Libraries” of an executable work include anything, other  
than the work as a whole, that (a) is included in the normal form of  
packaging a Major Component, but which is not part of that Major  
Component, and (b) serves only to enable use of the work with that  
Major Component, or to implement a Standard Interface for which an  
implementation is available to the public in source code form. A “Major  
Component”, in this context, means a major essential component  
(kernel, window system, and so on) of the specific operating system (if  
any) on which the executable work runs, or a compiler used to produce  
the work, or an object code interpreter used to run it.  
When we speak of free software, we are referring to freedom, not price.  
Our General Public Licenses are designed to make sure that you have  
the freedom to distribute copies of free software (and charge for them if  
you wish), that you receive source code or can get it if you want it, that  
you can change the software or use pieces of it in new free programs,  
and that you know you can do these things.  
To protect your rights, we need to prevent others from denying you  
these rights or asking you to surrender the rights. Therefore, you have  
certain responsibilities if you distribute copies of the software, or if you  
modify it: responsibilities to respect the freedom of others.  
The “Corresponding Source” for a work in object code form means all  
the source code needed to generate, install, and (for an executable  
work) run the object code and to modify the work, including scripts to  
control those activities. However, it does not include the work’s System  
Libraries, or general-purpose tools or generally available free programs  
which are used unmodified in performing those activities but which are  
not part of the work. For example, Corresponding Source includes  
interface definition files associated with source files for the work, and the  
source code for shared libraries and dynamically linked subprograms  
that the work is specifically designed to require, such as by intimate  
data communication or control flow between those subprograms and  
other parts of the work.  
For example, if you distribute copies of such a program, whether gratis  
or for a fee, you must pass on to the recipients the same freedoms that  
you received. You must make sure that they, too, receive or can get the  
source code. And you must show them these terms so they know their  
rights.  
Developers that use the GNU GPL protect your rights with two steps:  
(1) assert copyright on the software, and (2) offer you this License giving  
you legal permission to copy, distribute and/or modify it.  
For the developers’ and authors’ protection, the GPL clearly explains  
that there is no warranty for this free software. For both users’ and  
authors’ sake, the GPL requires that modified versions be marked as  
changed, so that their problems will not be attributed erroneously to  
authors of previous versions.  
The Corresponding Source need not include anything that users can  
regenerate automatically from other parts of the Corresponding Source.  
The Corresponding Source for a work in source code form is that same  
Some devices are designed to deny users access to install or run  
modified versions of the software inside them, although the  
work.  
manufacturer can do so. This is fundamentally incompatible with the  
aim of protecting users’ freedom to change the software. The  
systematic pattern of such abuse occurs in the area of products for  
individuals to use, which is precisely where it is most unacceptable.  
Therefore, we have designed this version of the GPL to prohibit the  
practice for those products. If such problems arise substantially in other  
domains, we stand ready to extend this provision to those domains in  
future versions of the GPL, as needed to protect the freedom of users.  
2. Basic Permissions.  
All rights granted under this License are granted for the term of  
copyright on the Program, and are irrevocable provided the stated  
conditions are met. This License explicitly affirms your unlimited  
permission to run the unmodified Program. The output from running a  
covered work is covered by this License only if the output, given its  
content, constitutes a covered work. This License acknowledges your  
rights of fair use or other equivalent, as provided by copyright law.  
Finally, every program is threatened constantly by software patents.  
States should not allow patents to restrict development and use of  
software on general-purpose computers, but in those that do, we wish  
to avoid the special danger that patents applied to a free program could  
make it effectively proprietary. To prevent this, the GPL assures that  
patents cannot be used to render the program non-free.  
You may make, run and propagate covered works that you do not  
convey, without conditions so long as your license otherwise remains in  
force. You may convey covered works to others for the sole purpose of  
having them make modifications exclusively for you, or provide you with  
facilities for running those works, provided that you comply with the  
terms of this License in conveying all material for which you do not  
control copyright. Those thus making or running the covered works for  
you must do so exclusively on your behalf, under your direction and  
control, on terms that prohibit them from making any copies of your  
copyrighted material outside their relationship with you.  
The precise terms and conditions for copying, distribution and  
mTEodRifiMcatSionAfNolloDw.CONDITIONS  
0. Definitions.  
Conveying under any other circumstances is permitted solely under the  
conditions stated below. Sublicensing is not allowed; section 10 makes  
it unnecessary.  
“This License” refers to version 3 of the GNU General Public License.  
“Copyright” also means copyright-like laws that apply to other kinds of  
works, such as semiconductor masks.  
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.  
“The Program” refers to any copyrightable work licensed under this  
License. Each licensee is addressed as “you”. “Licensees” and  
“recipients” may be individuals or organizations.  
No covered work shall be deemed part of an effective technological  
measure under any applicable law fulfilling obligations under article 11 of  
the WIPO copyright treaty adopted on 20 December 1996, or similar  
laws prohibiting or restricting circumvention of such measures.  
To “modify” a work means to copy from or adapt all or part of the work  
in a fashion requiring copyright permission, other than the making of an  
exact copy. The resulting work is called a “modified version” of the  
earlier work or a work “based on” the earlier work.  
When you convey a covered work, you waive any legal power to forbid  
circumvention of technological measures to the extent such  
circumvention is effected by exercising rights under this License with  
respect to the covered work, and you disclaim any intention to limit  
operation or modification of the work as a means of enforcing, against  
the work’s users, your or third parties’ legal rights to forbid  
circumvention of technological measures.  
A “covered work” means either the unmodified Program or a work  
based on the Program.  
To “propagate” a work means to do anything with it that, without  
permission, would make you directly or secondarily liable for  
infringement under applicable copyright law, except executing it on a  
computer or modifying a private copy. Propagation includes copying,  
distribution (with or without modification), making available to the public,  
and in some countries other activities as well.  
4. Conveying Verbatim Copies.  
You may convey verbatim copies of the Program’s source code as you  
receive it, in any medium, provided that you conspicuously and  
appropriately publish on each copy an appropriate copyright notice;  
keep intact all notices stating that this License and any non-permissive  
To “convey” a work means any kind of propagation that enables other  
parties to make or receive copies. Mere interaction with a user through  
Download from Www.Somanuals.com. All Manuals Search And Download.  
terms added in accord with section 7 apply to the code; keep intact all  
notices of the absence of any warranty; and give all recipients a copy of  
this License along with the Program.  
A separable portion of the object code, whose source code is excluded  
from the Corresponding Source as a System Library, need not be  
included in conveying the object code work.  
You may charge any price or no price for each copy that you convey,  
A “User Product” is either (1) a “consumer product”, which means any  
tangible personal property which is normally used for personal, family, or  
household purposes, or (2) anything designed or sold for incorporation  
into a dwelling. In determining whether a product is a consumer  
product, doubtful cases shall be resolved in favor of coverage. For a  
particular product received by a particular user, “normally used” refers to  
a typical or common use of that class of product, regardless of the  
status of the particular user or of the way in which the particular user  
actually uses, or expects or is expected to use, the product. A product  
is a consumer product regardless of whether the product has  
and you may offer support or warranty protection for a fee.  
5. Conveying Modified Source Versions.  
You may convey a work based on the Program, or the modifications to  
produce it from the Program, in the form of source code under the  
terms of section 4, provided that you also meet all of these conditions:  
a) The work must carry prominent notices stating that you modified  
it, and giving a relevant date.  
substantial commercial, industrial or non-consumer uses, unless such  
uses represent the only significant mode of use of the product.  
b) The work must carry prominent notices stating that it is released  
under this License and any conditions added under section 7. This  
requirement modifies the requirement in section 4 to “keep intact all  
notices”.  
“Installation Information” for a User Product means any methods,  
procedures, authorization keys, or other information required to install  
and execute modified versions of a covered work in that User Product  
from a modified version of its Corresponding Source. The information  
must suffice to ensure that the continued functioning of the modified  
object code is in no case prevented or interfered with solely because  
modification has been made.  
c) You must license the entire work, as a whole, under this License  
to anyone who comes into possession of a copy. This License will  
therefore apply, along with any applicable section 7 additional  
terms, to the whole of the work, and all its parts, regardless of  
how they are packaged. This License gives no permission to  
license the work in any other way, but it does not invalidate such  
permission if you have separately received it.  
If you convey an object code work under this section in, or with, or  
specifically for use in, a User Product, and the conveying occurs as part  
of a transaction in which the right of possession and use of the User  
Product is transferred to the recipient in perpetuity or for a fixed term  
(regardless of how the transaction is characterized), the Corresponding  
Source conveyed under this section must be accompanied by the  
Installation Information. But this requirement does not apply if neither  
you nor any third party retains the ability to install modified object code  
on the User Product (for example, the work has been installed in ROM).  
d) If the work has interactive user interfaces, each must display  
Appropriate Legal Notices; however, if the Program has interactive  
interfaces that do not display Appropriate Legal Notices, your  
work need not make them do so.  
A compilation of a covered work with other separate and independent  
works, which are not by their nature extensions of the covered work,  
and which are not combined with it such as to form a larger program, in  
or on a volume of a storage or distribution medium, is called an  
“aggregate” if the compilation and its resulting copyright are not used to  
limit the access or legal rights of the compilation’s users beyond what  
the individual works permit. Inclusion of a covered work in an aggregate  
does not cause this License to apply to the other parts of the  
aggregate.  
The requirement to provide Installation Information does not include a  
requirement to continue to provide support service, warranty, or  
updates for a work that has been modified or installed by the recipient,  
or for the User Product in which it has been modified or installed.  
Access to a network may be denied when the modification itself  
materially and adversely affects the operation of the network or violates  
the rules and protocols for communication across the network.  
Corresponding Source conveyed, and Installation Information provided,  
in accord with this section must be in a format that is publicly  
documented (and with an implementation available to the public in  
source code form), and must require no special password or key for  
unpacking, reading or copying.  
6. Conveying Non-Source Forms.  
You may convey a covered work in object code form under the terms of  
sections 4 and 5, provided that you also convey the machine-readable  
Corresponding Source under the terms of this License, in one of these  
ways:  
a) Convey the object code in, or embodied in, a physical product  
(including a physical distribution medium), accompanied by the  
Corresponding Source fixed on a durable physical medium  
customarily used for software interchange.  
7. Additional Terms.  
“Additional permissions” are terms that supplement the terms of this  
License by making exceptions from one or more of its conditions.  
Additional permissions that are applicable to the entire Program shall be  
treated as though they were included in this License, to the extent that  
they are valid under applicable law. If additional permissions apply only  
to part of the Program, that part may be used separately under those  
permissions, but the entire Program remains governed by this License  
without regard to the additional permissions.  
b) Convey the object code in, or embodied in, a physical product  
(including a physical distribution medium), accompanied by a  
written offer, valid for at least three years and valid for as long as  
you offer spare parts or customer support for that product model,  
to give anyone who possesses the object code either (1) a copy of  
the Corresponding Source for all the software in the product that  
is covered by this License, on a durable physical medium  
customarily used for software interchange, for a price no more  
than your reasonable cost of physically performing this conveying  
of source, or (2) access to copy the Corresponding Source from a  
network server at no charge.  
When you convey a copy of a covered work, you may at your option  
remove any additional permissions from that copy, or from any part of it.  
(Additional permissions may be written to require their own removal in  
certain cases when you modify the work.) You may place additional  
permissions on material, added by you to a covered work, for which  
you have or can give appropriate copyright permission.  
c) Convey individual copies of the object code with a copy of the  
written offer to provide the Corresponding Source. This alternative  
is allowed only occasionally and noncommercially, and only if you  
received the object code with such an offer, in accord with  
subsection 6b.  
Notwithstanding any other provision of this License, for material you add  
to a covered work, you may (if authorized by the copyright holders of  
that material) supplement the terms of this License with terms:  
a) Disclaiming warranty or limiting liability differently from the terms of  
sections 15 and 16 of this License; or  
d) Convey the object code by offering access from a designated  
place (gratis or for a charge), and offer equivalent access to the  
Corresponding Source in the same way through the same place at  
no further charge. You need not require recipients to copy the  
Corresponding Source along with the object code. If the place to  
copy the object code is a network server, the Corresponding  
Source may be on a different server (operated by you or a third  
party) that supports equivalent copying facilities, provided you  
maintain clear directions next to the object code saying where to  
find the Corresponding Source. Regardless of what server hosts  
the Corresponding Source, you remain obligated to ensure that it  
is available for as long as needed to satisfy these requirements.  
b) Requiring preservation of specified reasonable legal notices or  
author attributions in that material or in the Appropriate Legal  
Notices displayed by works containing it; or  
c) Prohibiting misrepresentation of the origin of that material, or  
requiring that modified versions of such material be marked in  
reasonable ways as different from the original version; or  
d) Limiting the use for publicity purposes of names of licensors or  
authors of the material; or  
e) Declining to grant rights under trademark law for use of some  
trade names, trademarks, or service marks; or  
e) Convey the object code using peer-to-peer transmission, provided  
you inform other peers where the object code and Corresponding  
Source of the work are being offered to the general public at no  
charge under subsection 6d.  
f) Requiring indemnification of licensors and authors of that material  
by anyone who conveys the material (or modified versions of it)  
with contractual assumptions of liability to the recipient, for any  
liability that these contractual assumptions directly impose on  
those licensors and authors.  
All other non-permissive additional terms are considered “further  
restrictions” within the meaning of section 10. If the Program as you  
received it, or any part of it, contains a notice stating that it is governed  
by this License along with a term that is a further restriction, you may  
remove that term. If a license document contains a further restriction but  
Download from Www.Somanuals.com. All Manuals Search And Download.  
permits relicensing or conveying under this License, you may add to a  
covered work material governed by the terms of that license document,  
provided that the further restriction does not survive such relicensing or  
conveying.  
In the following three paragraphs, a “patent license” is any express  
agreement or commitment, however denominated, not to enforce a  
patent (such as an express permission to practice a patent or covenant  
not to sue for patent infringement). To “grant” such a patent license to a  
party means to make such an agreement or commitment not to enforce  
a patent against the party.  
If you add terms to a covered work in accord with this section, you  
must place, in the relevant source files, a statement of the additional  
terms that apply to those files, or a notice indicating where to find the  
applicable terms.  
If you convey a covered work, knowingly relying on a patent license, and  
the Corresponding Source of the work is not available for anyone to copy,  
free of charge and under the terms of this License, through a publicly  
available network server or other readily accessible means, then you must  
either (1) cause the Corresponding Source to be so available, or (2)  
arrange to deprive yourself of the benefit of the patent license for this  
particular work, or (3) arrange, in a manner consistent with the  
requirements of this License, to extend the patent license to downstream  
recipients. “Knowingly relying” means you have actual knowledge that, but  
for the patent license, your conveying the covered work in a country, or  
your recipient’s use of the covered work in a country, would infringe one or  
more identifiable patents in that country that you have reason to believe  
are valid.  
Additional terms, permissive or non-permissive, may be stated in the  
form of a separately written license, or stated as exceptions; the above  
requirements apply either way.  
8. Termination.  
You may not propagate or modify a covered work except as expressly  
provided under this License. Any attempt otherwise to propagate or  
modify it is void, and will automatically terminate your rights under this  
License (including any patent licenses granted under the third paragraph  
of section 11).  
If, pursuant to or in connection with a single transaction or arrangement,  
you convey, or propagate by procuring conveyance of, a covered work,  
and grant a patent license to some of the parties receiving the covered  
work authorizing them to use, propagate, modify or convey a specific  
copy of the covered work, then the patent license you grant is  
automatically extended to all recipients of the covered work and works  
based on it.  
However, if you cease all violation of this License, then your license from  
a particular copyright holder is reinstated (a) provisionally, unless and  
until the copyright holder explicitly and finally terminates your license,  
and (b) permanently, if the copyright holder fails to notify you of the  
violation by some reasonable means prior to 60 days after the  
cessation.  
Moreover, your license from a particular copyright holder is reinstated  
permanently if the copyright holder notifies you of the violation by some  
reasonable means, this is the first time you have received notice of  
violation of this License (for any work) from that copyright holder, and  
you cure the violation prior to 30 days after your receipt of the notice.  
A patent license is “discriminatory” if it does not include within the scope  
of its coverage, prohibits the exercise of, or is conditioned on the  
non-exercise of one or more of the rights that are specifically granted  
under this License. You may not convey a covered work if you are a  
party to an arrangement with a third party that is in the business of  
distributing software, under which you make payment to the third party  
based on the extent of your activity of conveying the work, and under  
which the third party grants, to any of the parties who would receive the  
covered work from you, a discriminatory patent license (a) in connection  
with copies of the covered work conveyed by you (or copies made from  
those copies), or (b) primarily for and in connection with specific  
products or compilations that contain the covered work, unless you  
entered into that arrangement, or that patent license was granted, prior  
to 28 March 2007.  
Termination of your rights under this section does not terminate the  
licenses of parties who have received copies or rights from you under  
this License. If your rights have been terminated and not permanently  
reinstated, you do not qualify to receive new licenses for the same  
material under section 10.  
9. Acceptance Not Required for Having Copies.  
You are not required to accept this License in order to receive or run a  
copy of the Program. Ancillary propagation of a covered work occurring  
solely as a consequence of using peer-to-peer transmission to receive a  
copy likewise does not require acceptance. However, nothing other  
than this License grants you permission to propagate or modify any  
covered work. These actions infringe copyright if you do not accept this  
License. Therefore, by modifying or propagating a covered work, you  
indicate your acceptance of this License to do so.  
Nothing in this License shall be construed as excluding or limiting any  
implied license or other defenses to infringement that may otherwise be  
available to you under applicable patent law.  
12. No Surrender of Others’ Freedom.  
If conditions are imposed on you (whether by court order, agreement or  
otherwise) that contradict the conditions of this License, they do not  
excuse you from the conditions of this License. If you cannot convey a  
covered work so as to satisfy simultaneously your obligations under this  
License and any other pertinent obligations, then as a consequence you  
may not convey it at all. For example, if you agree to terms that obligate  
you to collect a royalty for further conveying from those to whom you  
convey the Program, the only way you could satisfy both those terms  
and this License would be to refrain entirely from conveying the  
Program.  
10. Automatic Licensing of Downstream Recipients.  
Each time you convey a covered work, the recipient automatically  
receives a license from the original licensors, to run, modify and  
propagate that work, subject to this License. You are not responsible for  
enforcing compliance by third parties with this License.  
An “entity transaction” is a transaction transferring control of an  
organization, or substantially all assets of one, or subdividing an  
organization, or merging organizations. If propagation of a covered work  
results from an entity transaction, each party to that transaction who  
receives a copy of the work also receives whatever licenses to the work  
the party’s predecessor in interest had or could give under the previous  
paragraph, plus a right to possession of the Corresponding Source of  
the work from the predecessor in interest, if the predecessor has it or  
can get it with reasonable efforts.  
13. Use with the GNU Affero General Public License.  
Notwithstanding any other provision of this License, you have  
permission to link or combine any covered work with a work licensed  
under version 3 of the GNU Affero General Public License into a single  
combined work, and to convey the resulting work. The terms of this  
License will continue to apply to the part which is the covered work, but  
the special requirements of the GNU Affero General Public License,  
section 13, concerning interaction through a network will apply to the  
combination as such.  
You may not impose any further restrictions on the exercise of the rights  
granted or affirmed under this License. For example, you may not  
impose a license fee, royalty, or other charge for exercise of rights  
granted under this License, and you may not initiate litigation (including  
a cross-claim or counterclaim in a lawsuit) alleging that any patent claim  
is infringed by making, using, selling, offering for sale, or importing the  
Program or any portion of it.  
14. Revised Versions of this License.  
The Free Software Foundation may publish revised and/or new versions  
of the GNU General Public License from time to time. Such new  
versions will be similar in spirit to the present version, but may differ in  
detail to address new problems or concerns.  
11. Patents.  
A “contributor” is a copyright holder who authorizes use under this  
License of the Program or a work on which the Program is based. The  
work thus licensed is called the contributor’s “contributor version”.  
Each version is given a distinguishing version number. If the Program  
specifies that a certain numbered version of the GNU General Public  
License “or any later version” applies to it, you have the option of  
following the terms and conditions either of that numbered version or of  
any later version published by the Free Software Foundation. If the  
Program does not specify a version number of the GNU General Public  
License, you may choose any version ever published by the Free  
Software Foundation.  
A contributor’s “essential patent claims” are all patent claims owned or  
controlled by the contributor, whether already acquired or hereafter  
acquired, that would be infringed by some manner, permitted by this  
License, of making, using, or selling its contributor version, but do not  
include claims that would be infringed only as a consequence of further  
modification of the contributor version. For purposes of this definition,  
“control” includes the right to grant patent sublicenses in a manner  
consistent with the requirements of this License.  
If the Program specifies that a proxy can decide which future versions of  
the GNU General Public License can be used, that proxy’s public  
statement of acceptance of a version permanently authorizes you to  
choose that version for the Program.  
Each contributor grants you a non-exclusive, worldwide, royalty-free  
patent license under the contributor’s essential patent claims, to make,  
use, sell, offer for sale, import and otherwise run, modify and propagate  
the contents of its contributor version.  
Later license versions may give you additional or different permissions.  
However, no additional obligations are imposed on any author or  
copyright holder as a result of your choosing to follow a later version.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. Disclaimer of Warranty.  
Finally, software patents pose a constant threat to the existence of any  
free program. We wish to make sure that a company cannot effectively  
restrict the users of a free program by obtaining a restrictive license from  
a patent holder. Therefore, we insist that any patent license obtained for  
a version of the library must be consistent with the full freedom of use  
specified in this license.  
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE  
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY  
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
Most GNU software, including some libraries, is covered by the ordinary  
GNU General Public License. This license, the GNU Lesser General  
Public License, applies to certain designated libraries, and is quite  
different from the ordinary General Public License. We use this license  
for certain libraries in order to permit linking those libraries into non-free  
programs.  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF  
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE  
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY  
SERVICING, REPAIR OR CORRECTION.  
When a program is linked with a library, whether statically or using a  
shared library, the combination of the two is legally speaking a  
combined work, a derivative of the original library. The ordinary General  
Public License therefore permits such linking only if the entire  
combination fits its criteria of freedom. The Lesser General Public  
License permits more lax criteria for linking other code with the library.  
16. Limitation of Liability.  
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR  
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM  
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,  
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR  
We call this license the “Lesser” General Public License because it does  
Less to protect the user’s freedom than the ordinary General Public  
License. It also provides other free software developers Less of an  
advantage over competing non-free programs. These disadvantages  
are the reason we use the ordinary General Public License for many  
libraries. However, the Lesser license provides advantages in certain  
special circumstances.  
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED  
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR  
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF  
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN  
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
For example, on rare occasions, there may be a special need to  
encourage the widest possible use of a certain library, so that it  
becomes a de-facto standard. To achieve this, non-free programs must  
be allowed to use the library. A more frequent case is that a free library  
does the same job as widely used non-free libraries. In this case, there  
is little to gain by limiting the free library to free software only, so we use  
the Lesser General Public License.  
17. Interpretation of Sections 15 and 16.  
If the disclaimer of warranty and limitation of liability provided above  
cannot be given local legal effect according to their terms, reviewing  
courts shall apply local law that most closely approximates an absolute  
waiver of all civil liability in connection with the Program, unless a  
warranty or assumption of liability accompanies a copy of the Program  
in return for a fee.  
In other cases, permission to use a particular library in non-free  
programs enables a greater number of people to use a large body of  
free software. For example, permission to use the GNU C Library in  
non-free programs enables many more people to use the whole GNU  
operating system, as well as its variant, the GNU/Linux operating  
system.  
END OF TERMS AND CONDITIONS  
GNU LESSER GENERAL PUBLIC LICENSE  
Version 2.1, February 1999  
Although the Lesser General Public License is Less protective of the  
users’ freedom, it does ensure that the user of a program that is linked  
with the Library has the freedom and the wherewithal to run that  
program using a modified version of the Library.  
Copyright (C) 1991, 1999 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA  
Everyone is permitted to copy and distribute verbatim copies of this  
The precise terms and conditions for copying, distribution and  
modification follow. Pay close attention to the difference between a  
“work based on the library” and a “work that uses the library”. The  
former contains code derived from the library, whereas the latter must  
be combined with the library in order to run.  
license document, but changing it is not allowed.  
[This is the first released version of the Lesser GPL.  
It also counts as the successor of the GNU Library Public License,  
vPerrseioanm2,bhleence the version number 2.1.]  
TERMS AND CONDITIONS FOR COPYING,  
DISTRIBUTION AND MODIFICATION  
The licenses for most software are designed to take away your freedom  
to share and change it. By contrast, the GNU General Public Licenses  
are intended to guarantee your freedom to share and change free  
software to make sure the software is free for all its users.  
0. This License Agreement applies to any software library or other  
program which contains a notice placed by the copyright holder or  
other authorized party saying it may be distributed under the terms of  
this Lesser General Public License (also called “this License”). Each  
licensee is addressed as “you”.  
This license, the Lesser General Public License, applies to some  
specially designated software packages--typically libraries--of the Free  
Software Foundation and other authors who decide to use it. You can  
use it too, but we suggest you first think carefully about whether this  
license or the ordinary General Public License is the better strategy to  
use in any particular case, based on the explanations below.  
A “library” means a collection of software functions and/or data  
prepared so as to be conveniently linked with application programs  
(which use some of those functions and data) to form executables.  
The “Library”, below, refers to any such software library or work which  
has been distributed under these terms. A “work based on the Library”  
means either the Library or any derivative work under copyright law: that  
is to say, a work containing the Library or a portion of it, either verbatim  
or with modifications and/or translated straightforwardly into another  
language. (Hereinafter, translation is included without limitation in the  
term “modification”.)  
When we speak of free software, we are referring to freedom of use, not  
price. Our General Public Licenses are designed to make sure that you  
have the freedom to distribute copies of free software (and charge for  
this service if you wish); that you receive source code or can get it if you  
want it; that you can change the software and use pieces of it in new  
free programs; and that you are informed that you can do these things.  
“Source code” for a work means the preferred form of the work for  
making modifications to it. For a library, complete source code means  
all the source code for all modules it contains, plus any associated  
interface definition files, plus the scripts used to control compilation and  
installation of the library.  
To protect your rights, we need to make restrictions that forbid  
distributors to deny you these rights or to ask you to surrender these  
rights. These restrictions translate to certain responsibilities for you if you  
distribute copies of the library or if you modify it.  
For example, if you distribute copies of the library, whether gratis or for a  
fee, you must give the recipients all the rights that we gave you. You  
must make sure that they, too, receive or can get the source code. If  
you link other code with the library, you must provide complete object  
files to the recipients, so that they can relink them with the library after  
making changes to the library and recompiling it. And you must show  
them these terms so they know their rights.  
Activities other than copying, distribution and modification are not  
covered by this License; they are outside its scope. The act of running a  
program using the Library is not restricted, and output from such a  
program is covered only if its contents constitute a work based on the  
Library (independent of the use of the Library in a tool for writing it).  
Whether that is true depends on what the Library does and what the  
program that uses the Library does.  
We protect your rights with a two-step method: (1) we copyright the  
library, and (2) we offer you this license, which gives you legal  
permission to copy, distribute and/or modify the library.  
1. You may copy and distribute verbatim copies of the Library’s  
complete source code as you receive it, in any medium, provided that  
you conspicuously and appropriately publish on each copy an  
appropriate copyright notice and disclaimer of warranty; keep intact all  
the notices that refer to this License and to the absence of any  
warranty; and distribute a copy of this License along with the Library.  
To protect each distributor, we want to make it very clear that there is no  
warranty for the free library. Also, if the library is modified by someone  
else and passed on, the recipients should know that what they have is  
not the original version, so that the original author’s reputation will not be  
affected by problems that might be introduced by others.  
You may charge a fee for the physical act of transferring a copy, and  
Download from Www.Somanuals.com. All Manuals Search And Download.  
you may at your option offer warranty protection in exchange for a fee.  
lines or less in length), then the use of the object file is unrestricted,  
regardless of whether it is legally a derivative work. (Executables  
containing this object code plus portions of the Library will still fall under  
Section 6.)  
2. You may modify your copy or copies of the Library or any portion of  
it, thus forming a work based on the Library, and copy and distribute  
such modifications or work under the terms of Section 1 above,  
provided that you also meet all of these conditions:  
Otherwise, if the work is a derivative of the Library, you may distribute  
the object code for the work under the terms of Section 6. Any  
executables containing that work also fall under Section 6, whether or  
not they are linked directly with the Library itself.  
a) The modified work must itself be a software library.  
b) You must cause the files modified to carry prominent notices  
stating that you changed the files and the date of any change.  
6. As an exception to the Sections above, you may also combine or link  
a “work that uses the Library” with the Library to produce a work  
containing portions of the Library, and distribute that work under terms  
of your choice, provided that the terms permit modification of the work  
for the customer’s own use and reverse engineering for debugging such  
modifications.  
c) You must cause the whole of the work to be licensed at no charge  
to all third parties under the terms of this License.  
d) If a facility in the modified Library refers to a function or a table of  
data to be supplied by an application program that uses the  
facility, other than as an argument passed when the facility is  
invoked, then you must make a good faith effort to ensure that, in  
the event an application does not supply such function or table,  
the facility still operates, and performs whatever part of its purpose  
remains meaningful.  
You must give prominent notice with each copy of the work that the  
Library is used in it and that the Library and its use are covered by this  
License. You must supply a copy of this License. If the work during  
execution displays copyright notices, you must include the copyright  
notice for the Library among them, as well as a reference directing the  
user to the copy of this License. Also, you must do one of these things:  
(For example, a function in a library to compute square roots has a  
purpose that is entirely well-defined independent of the application.  
Therefore, Subsection 2d requires that any application-supplied function  
or table used by this function must be optional: if the application does  
not supply it, the square root function must still compute square roots.)  
a) Accompany the work with the complete corresponding machine-  
readable source code for the Library including whatever changes  
were used in the work (which must be distributed under Sections  
1 and 2 above); and, if the work is an executable linked with the  
Library, with the complete machine readable “work that uses the  
Library”, as object code and/or source code, so that the user can  
modify the Library and then relink to produce a modified  
executable containing the modified Library. (It is understood that  
the user who changes the contents of definitions files in the Library  
will not necessarily be able to recompile the application to use the  
modified definitions.)  
These requirements apply to the modified work as a whole. If identifiable  
sections of that work are not derived from the Library, and can be  
reasonably considered independent and separate works in themselves,  
then this License, and its terms, do not apply to those sections when  
you distribute them as separate works. But when you distribute the  
same sections as part of a whole which is a work based on the Library,  
the distribution of the whole must be on the terms of this License,  
whose permissions for other licensees extend to the entire whole, and  
thus to each and every part regardless of who wrote it.  
b) Use a suitable shared library mechanism for linking with the Library.  
A suitable mechanism is one that (1) uses at run time a copy of the  
library already present on the user’s computer system, rather than  
copying library functions into the executable, and (2) will operate  
properly with a modified version of the library, if the user installs  
one, as long as the modified version is interface-compatible with  
the version that the work was made with.  
Thus, it is not the intent of this section to claim rights or contest your  
rights to work written entirely by you; rather, the intent is to exercise the  
right to control the distribution of derivative or collective works based on  
the Library.  
In addition, mere aggregation of another work not based on the Library  
with the Library (or with a work based on the Library) on a volume of a  
storage or distribution medium does not bring the other work under the  
scope of this License.  
c) Accompany the work with a written offer, valid for at least three  
years, to give the same user the materials specified in Subsection  
6a, above, for a charge no more than the cost of performing this  
distribution.  
3. You may opt to apply the terms of the ordinary GNU General Public  
License instead of this License to a given copy of the Library. To do this,  
you must alter all the notices that refer to this License, so that they refer  
to the ordinary GNU General Public License, version 2, instead of to this  
License. (If a newer version than version 2 of the ordinary GNU General  
Public License has appeared, then you can specify that version instead  
if you wish.) Do not make any other change in these notices.  
d) If distribution of the work is made by offering access to copy from  
a designated place, offer equivalent access to copy the above  
specified materials from the same place.  
e) Verify that the user has already received a copy of these materials  
or that you have already sent this user a copy.  
For an executable, the required form of the “work that uses the Library”  
must include any data and utility programs needed for reproducing the  
executable from it. However, as a special exception, the materials to be  
distributed need not include anything that is normally distributed (in  
either source or binary form) with the major components (compiler,  
kernel, and so on) of the operating system on which the executable  
runs, unless that component itself accompanies the executable.  
Once this change is made in a given copy, it is irreversible for that copy,  
so the ordinary GNU General Public License applies to all subsequent  
copies and derivative works made from that copy.  
This option is useful when you wish to copy part of the code of the  
Library into a program that is not a library.  
4. You may copy and distribute the Library (or a portion or derivative of  
it, under Section 2) in object code or executable form under the terms  
of Sections 1 and 2 above provided that you accompany it with the  
complete corresponding machine-readable source code, which must  
be distributed under the terms of Sections 1 and 2 above on a medium  
customarily used for software interchange.  
It may happen that this requirement contradicts the license restrictions  
of other proprietary libraries that do not normally accompany the  
operating system. Such a contradiction means you cannot use both  
them and the Library together in an executable that you distribute.  
7. You may place library facilities that are a work based on the Library  
side-by-side in a single library together with other library facilities not  
covered by this License, and distribute such a combined library,  
provided that the separate distribution of the work based on the Library  
and of the other library facilities is otherwise permitted, and provided  
that you do these two things:  
If distribution of object code is made by offering access to copy from a  
designated place, then offering equivalent access to copy the source  
code from the same place satisfies the requirement to distribute the  
source code, even though third parties are not compelled to copy the  
source along with the object code.  
a) Accompany the combined library with a copy of the same work  
based on the Library, uncombined with any other library facilities.  
This must be distributed under the terms of the Sections above.  
5. A program that contains no derivative of any portion of the Library,  
but is designed to work with the Library by being compiled or linked  
with it, is called a “work that uses the Library”. Such a work, in isolation,  
is not a derivative work of the Library, and therefore falls outside the  
scope of this License.  
b) Give prominent notice with the combined library of the fact that part  
of it is a work based on the Library, and explaining where to find the  
accompanying uncombined form of the same work.  
However, linking a “work that uses the Library” with the Library creates  
an executable that is a derivative of the Library (because it contains  
portions of the Library), rather than a “work that uses the library”. The  
executable is therefore covered by this License. Section 6 states terms  
for distribution of such executables.  
8. You may not copy, modify, sublicense, link with, or distribute the  
Library except as expressly provided under this License. Any attempt  
otherwise to copy, modify, sublicense, link with, or distribute the Library  
is void, and will automatically terminate your rights under this License.  
However, parties who have received copies, or rights, from you under  
this License will not have their licenses terminated so long as such  
parties remain in full compliance.  
When a “work that uses the Library” uses material from a header file  
that is part of the Library, the object code for the work may be a  
derivative work of the Library even though the source code is not.  
Whether this is true is especially significant if the work can be linked  
without the Library, or if the work is itself a library. The threshold for this  
to be true is not precisely defined by law.  
9. You are not required to accept this License, since you have not signed  
it. However, nothing else grants you permission to modify or distribute  
the Library or its derivative works. These actions are prohibited by law if  
you do not accept this License. Therefore, by modifying or distributing  
the Library (or any work based on the Library), you indicate your  
acceptance of this License to do so, and all its terms and conditions for  
If such an object file uses only numerical parameters, data structure  
layouts and accessors, and small macros and small inline functions (ten  
Download from Www.Somanuals.com. All Manuals Search And Download.  
copying, distributing or modifying the Library or works based on it.  
How to Apply These Terms to Your New Libraries  
10. Each time you redistribute the Library (or any work based on the  
Library), the recipient automatically receives a license from the original  
licensor to copy, distribute, link with or modify the Library subject to  
these terms and conditions. You may not impose any further restrictions  
on the recipients’ exercise of the rights granted herein. You are not  
responsible for enforcing compliance by third parties with this License.  
If you develop a new library, and you want it to be of the greatest  
possible use to the public, we recommend making it free software that  
everyone can redistribute and change. You can do so by permitting  
redistribution under these terms (or, alternatively, under the terms of the  
ordinary General Public License).  
To apply these terms, attach the following notices to the library. It is  
safest to attach them to the start of each source file to most effectively  
convey the exclusion of warranty; and each file should have at least the  
“copyright” line and a pointer to where the full notice is found. one line  
to give the library’s name and an idea of what it does.  
11. If, as a consequence of a court judgment or allegation of patent  
infringement or for any other reason (not limited to patent issues),  
conditions are imposed on you (whether by court order, agreement or  
otherwise) that contradict the conditions of this License, they do not  
excuse you from the conditions of this License. If you cannot distribute  
so as to satisfy simultaneously your obligations under this License and  
any other pertinent obligations, then as a consequence you may not  
distribute the Library at all. For example, if a patent license would not  
permit royalty free redistribution of the Library by all those who receive  
copies directly or indirectly through you, then the only way you could  
satisfy both it and this License would be to refrain entirely from  
distribution of the Library.  
Copyright (C) year name of author  
This library is free software; you can redistribute it and/or modify it under  
the terms of the GNU Lesser General Public License as published by  
the Free Software Foundation; either version 2.1 of the License, or (at  
your option) any later version.  
This library is distributed in the hope that it will be useful, but WITHOUT  
ANY WARRANTY; without even the implied warranty of  
If any portion of this section is held invalid or unenforceable under any  
particular circumstance, the balance of the section is intended to apply, and  
the section as a whole is intended to apply in other circumstances.  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See  
the GNU Lesser General Public License for more details.  
You should have received a copy of the GNU Lesser General Public  
License along with this library; if not, write to the Free Software  
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-  
1301 USA Also add information on how to contact you by electronic  
and paper mail.  
It is not the purpose of this section to induce you to infringe any patents or  
other property right claims or to contest validity of any such claims; this  
section has the sole purpose of protecting the integrity of the free software  
distribution system which is implemented by public license practices. Many  
people have made generous contributions to the wide range of software  
distributed through that system in reliance on consistent application of that  
system; it is up to the author/donor to decide if he or she is willing to  
distribute software through any other system and a licensee cannot impose  
that choice.  
You should also get your employer (if you work as a programmer) or  
your school, if any, to sign a “copyright disclaimer” for the library, if  
necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the library  
‘Frob’ (a library for tweaking knobs) written by James Random Hacker.  
This section is intended to make thoroughly clear what is believed to be  
a consequence of the rest of this License.  
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.  
12. If the distribution and/or use of the Library is restricted in certain  
countries either by patents or by copyrighted interfaces, the original  
copyright holder who places the Library under this License may add an  
explicit geographical distribution limitation excluding those countries, so  
that distribution is permitted only in or among countries not thus  
excluded. In such case, this License incorporates the limitation as if  
written in the body of this License.  
OpenSSL LICENSE  
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
13. The Free Software Foundation may publish revised and/or new  
versions of the Lesser General Public License from time to time. Such  
new versions will be similar in spirit to the present version, but may differ  
in detail to address new problems or concerns.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
Each version is given a distinguishing version number. If the Library  
specifies a version number of this License which applies to it and “any  
later version”, you have the option of following the terms and conditions  
either of that version or of any later version published by the Free  
Software Foundation. If the Library does not specify a license version  
number, you may choose any version ever published by the Free  
Software Foundation.  
3. All advertising materials mentioning features or use of this software  
must display the following acknowledgment: “This product includes  
software developed by the OpenSSL Project for use in the OpenSSL  
Toolkit. (http://www.openssl.org/)”  
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be  
used to endorse or promote products derived from this software  
without prior written permission. For written permission, please contact  
[email protected].  
14. If you wish to incorporate parts of the Library into other free  
programs whose distribution conditions are incompatible with these,  
write to the author to ask for permission. For software which is  
copyrighted by the Free Software Foundation, write to the Free  
Software Foundation; we sometimes make exceptions for this. Our  
decision will be guided by the two goals of preserving the free status of  
all derivatives of our free software and of promoting the sharing and  
reuse of software generally.  
5. Products derived from this software may not be called “OpenSSL”  
nor may “OpenSSL” appear in their names without prior written  
permission of the OpenSSL Project.  
6. Redistributions of any form whatsoever must retain the following  
acknowledgment: “This product includes software developed by the  
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.  
org/)”  
NO WARRANTY  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ‘‘AS IS’’  
AND ANY EXPRESSED OR  
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE  
IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED  
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN  
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES  
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,  
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED  
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO  
THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.  
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE  
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE  
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.This product includes cryptographic software written by Eric  
Young ([email protected]). This product includes software written by  
Tim Hudson ([email protected]).  
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR  
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE  
LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO  
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR  
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF  
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF  
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
Original SSLeay License  
Copyright (C) 1995-1998 Eric Young ([email protected]) All rights  
reserved. This package is an SSL implementation written by Eric Young  
([email protected]). The implementation was written so as to conform  
with Netscapes SSL. This library is free for commercial and non-  
commercial use as long as the following conditions are aheared to. The  
following conditions apply to all code found in this distribution, be it the  
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL  
END OF TERMS AND CONDITIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
documentation included with this distribution is covered by the same  
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.  
com).  
1.3. “Covered Software” means (a) the Original Software, or (b)  
Modifications, or (c) the combination of files containing Original Software  
with files containing Modifications, in each case including portions  
thereof.  
Copyright remains Eric Young’s, and as such any Copyright notices in  
the code are not to be removed.  
1.4. “Executable” means the Covered Software in any form other than  
If this package is used in a product, Eric Young should be given  
attribution as the author of the parts of the library used. This can be in  
the form of a textual message at program startup or in documentation  
(online or textual) provided with the package.Redistribution and use in  
source and binary forms, with or without modification, are permitted  
provided that the following conditions are met:  
Source Code.  
1.5. “Initial Developer” means the individual or entity that first makes  
Original Software available under this License.  
1.6. “Larger Work” means a work which combines Covered Software or  
portions thereof with code not governed by the terms of this License.  
1. Redistributions of source code must retain the copyright notice, this  
list of conditions and the following disclaimer.  
1.7. “License” means this document.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
1.8. “Licensable” means having the right to grant, to the maximum  
extent possible, whether at the time of the initial grant or subsequently  
acquired, any and all of the rights conveyed herein.  
3. All advertising materials mentioning features or use of this software  
must display the following acknowledgement: “This product includes  
cryptographic software written by Eric Young ([email protected])” The  
word ‘cryptographic’ can be left out if the rouines from the library being  
used are not cryptographic related :-).  
1.9. “Modifications” means the Source Code and Executable form of  
any of the following:  
A. Any file that results from an addition to, deletion from or  
modification of the contents of a file containing Original Software  
or previous Modifications;  
4. If you include any Windows specific code (or a derivative thereof) from  
the apps directory (application code) you must include an  
acknowledgement: “This product includes software written by Tim  
Hudson ([email protected])”  
B. Any new file that contains any part of the Original Software or  
previous Modifications; or  
C. Any new file that is contributed or otherwise made available under  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS IS’’ AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN  
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE  
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED  
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS  
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER  
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
the terms of this License.  
1.10. “Original Software” means the Source Code and Executable form  
of computer software code that is originally released under this License.  
1.11. “Patent Claims” means any patent claim(s), now owned or  
hereafter acquired, including without limitation, method, process, and  
apparatus claims, in any patent Licensable by grantor.  
1.12. “Source Code” means (a) the common form of computer software  
code in which modifications are made and (b) associated  
documentation included in or with such code.  
1.13. “You” (or “Your”) means an individual or a legal entity exercising  
rights under, and complying with all of the terms of, this License. For  
legal entities, “You” includes any entity which controls, is controlled by,  
or is under common control with You. For purposes of this definition,  
“control” means (a) the power, direct or indirect, to cause the direction  
or management of such entity, whether by contract or otherwise, or (b)  
ownership of more than fifty percent (50%) of the outstanding shares or  
beneficial ownership of such entity.  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE  
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGE.The licence and distribution terms for any publically  
available version or derivative of this code cannot be changed. i.e. this  
code cannot simply be copied and put under another distribution  
licence [including the GNU Public Licence.  
Boost Software License  
Boost Software License - Version 1.0 - August 17th, 2003 Permission is  
hereby granted, free of charge, to any person or organization obtaining  
a copy of the software and accompanying documentation covered by  
this license (the “Software”) to use, reproduce, display, distribute,  
execute, and transmit the Software, and to prepare derivative works of  
the Software, and to permit third-parties to whom the Software is  
furnished to do so, all subject to the following : The copyright notices in  
the Software and this entire statement, including the above license  
grant, this restriction and the following disclaimer, must be included in all  
copies of the Software, in whole or in part, and all derivative works of  
the Software, unless such copies or derivative works are solely in the  
form of machine-executable object code generated by a source  
language processor.  
2. License Grants.  
2.1. The Initial Developer Grant.  
Conditioned upon Your compliance with Section 3.1 below and subject  
to third party intellectual property claims, the Initial Developer hereby  
grants You a world-wide, royalty-free, non-exclusive license:  
a) under intellectual property rights (other than patent or trademark)  
Licensable by Initial Developer, to use, reproduce, modify, display,  
perform, sublicense and distribute the Original Software (or  
portions thereof), with or without Modifications, and/or as part of a  
Larger Work; and  
b) under Patent Claims infringed by the making, using or selling of  
Original Software, to make, have made, use, practice, sell, and  
offer for sale, and/or otherwise dispose of the Original Software (or  
portions thereof).  
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF  
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO  
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT. IN NO  
EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE  
c) The licenses granted in Sections 2.1(a) and (b) are effective on the  
date Initial Developer first distributes or otherwise makes the  
Original Software available to a third party under the terms of this  
License.  
DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR  
OTHER LIABILITY, WHETHER IN CONTRACT, TORT OR OTHERWISE,  
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE  
OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.  
d) Notwithstanding Section 2.1(b) above, no patent license is  
granted: (1) for code that You delete from the Original Software, or  
(2) for infringements caused by: (i) the modification of the Original  
Software, or (ii) the combination of the Original Software with other  
software or devices.  
COMMON DEVELOPMENT AND DISTRIBUTION  
LICENSE Version 1.0  
1. Definitions.  
2.2. Contributor Grant.  
1.1. “Contributor” means each individual or entity that creates or  
contributes to the creation of Modifications.  
Conditioned upon Your compliance with Section 3.1 below and subject  
to third party intellectual property claims, each Contributor hereby  
grants You a world-wide, royalty-free, non-exclusive license:  
1.2. “Contributor Version” means the combination of the Original  
Software, prior Modifications used by a Contributor (if any), and the  
Modifications made by that particular Contributor.  
a) under intellectual property rights (other than patent or trademark)  
Licensable by Contributor to use, reproduce, modify, display,  
perform, sublicense and distribute the Modifications created by  
such Contributor (or portions thereof), either on an unmodified  
basis, with other Modifications, as Covered Software and/or as  
part of a Larger Work; and  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) under Patent Claims infringed by the making, using, or selling of  
Modifications made by that Contributor either alone and/or in  
combination with its Contributor Version (or portions of such  
combination), to make, use, sell, offer for sale, have made, and/or  
otherwise dispose of: (1) Modifications made by that Contributor  
(or portions thereof); and (2) the combination of Modifications  
made by that Contributor with its Contributor Version (or portions  
of such combination).  
version will be given a distinguishing version number. Except as  
provided in Section 4.3, no one other than the license steward has the  
right to modify this License.  
4.2. Effect of New Versions.  
You may always continue to use, distribute or otherwise make the  
Covered Software available under the terms of the version of the  
License under which You originally received the Covered Software. If the  
Initial Developer includes a notice in the Original Software prohibiting it  
from being distributed or otherwise made available under any  
subsequent version of the License, You must distribute and make the  
Covered Software available under the terms of the version of the  
License under which You originally received the Covered Software.  
Otherwise, You may also choose to use, distribute or otherwise make  
the Covered Software available under the terms of any subsequent  
version of the License published by the license steward.  
c) The licenses granted in Sections 2.2(a) and 2.2(b) are effective on  
the date Contributor first distributes or otherwise makes the  
Modifications available to a third party.  
d) Notwithstanding Section 2.2(b) above, no patent license is  
granted: (1) for any code that Contributor has deleted from the  
Contributor Version; (2) for infringements caused by: (i) third party  
modifications of Contributor Version, or (ii) the combination of  
Modifications made by that Contributor with other software  
(except as part of the Contributor Version) or other devices; or (3)  
under Patent Claims infringed by Covered Software in the absence  
of Modifications made by that Contributor.  
4.3. Modified Versions.  
When You are an Initial Developer and You want to create a new license  
for Your Original Software, You may create and use a modified version  
of this License if You: (a) rename the license and remove any references  
to the name of the license steward (except to note that the license  
differs from this License); and (b) otherwise make it clear that the license  
contains terms which differ from this License.  
3. Distribution Obligations.  
3.1. Availability of Source Code.  
Any Covered Software that You distribute or otherwise make available in  
Executable form must also be made available in Source Code form and  
that Source Code form must be distributed only under the terms of this  
License. You must include a copy of this License with every copy of the  
Source Code form of the Covered Software You distribute or otherwise  
make available. You must inform recipients of any such Covered  
Software in Executable form as to how they can obtain such Covered  
Software in Source Code form in a reasonable manner on or through a  
medium customarily used for software exchange.  
5. DISCLAIMER OF WARRANTY.  
COVERED SOFTWARE IS PROVIDED UNDER THIS LICENSE ON AN  
“AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER  
EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,  
WARRANTIES THAT THE COVERED SOFTWARE IS FREE OF  
DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR  
NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE COVERED SOFTWARE IS WITH YOU.  
SHOULD ANY COVERED SOFTWARE PROVE DEFECTIVE IN ANY  
RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER  
CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY  
SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF  
WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE.  
NO USE OF ANY COVERED SOFTWARE IS AUTHORIZED  
HEREUNDER EXCEPT UNDER THIS DISCLAIMER.  
3.2. Modifications.  
The Modifications that You create or to which You contribute are  
governed by the terms of this License. You represent that You believe  
Your Modifications are Your original creation(s) and/or You have  
sufficient rights to grant the rights conveyed by this License.  
3.3. Required Notices.  
You must include a notice in each of Your Modifications that identifies  
You as the Contributor of the Modification. You may not remove or alter  
any copyright, patent or trademark notices contained within the  
Covered Software, or any notices of licensing or any descriptive text  
giving attribution to any Contributor or the Initial Developer.  
6. TERMINATION.  
6.1. This License and the rights granted hereunder will terminate  
automatically if You fail to comply with terms herein and fail to cure such  
breach within 30 days of becoming aware of the breach. Provisions  
which, by their nature, must remain in effect beyond the termination of  
this License shall survive.  
3.4. Application of Additional Terms.  
You may not offer or impose any terms on any Covered Software in  
Source Code form that alters or restricts the applicable version of this  
License or the recipients’ rights hereunder. You may choose to offer,  
and to charge a fee for, warranty, support, indemnity or liability  
obligations to one or more recipients of Covered Software. However,  
you may do so only on Your own behalf, and not on behalf of the Initial  
Developer or any Contributor. You must make it absolutely clear that any  
such warranty, support, indemnity or liability obligation is offered by You  
alone, and You hereby agree to indemnify the Initial Developer and every  
Contributor for any liability incurred by the Initial Developer or such  
Contributor as a result of warranty, support, indemnity or liability terms  
You offer.  
6.2. If You assert a patent infringement claim (excluding declaratory  
judgment actions) against Initial Developer or a Contributor (the Initial  
Developer or Contributor against whom You assert such claim is  
referred to as “Participant”) alleging that the Participant Software  
(meaning the Contributor Version where the Participant is a Contributor  
or the Original Software where the Participant is the Initial Developer)  
directly or indirectly infringes any patent, then any and all rights granted  
directly or indirectly to You by such Participant, the Initial Developer (if  
the Initial Developer is not the Participant) and all Contributors under  
Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from  
Participant terminate prospectively and automatically at the expiration of  
such 60 day notice period, unless if within such 60 day period You  
withdraw Your claim with respect to the Participant Software against  
such Participant either unilaterally or pursuant to a written agreement  
with Participant.  
3.5. Distribution of Executable Versions.  
You may distribute the Executable form of the Covered Software under  
the terms of this License or under the terms of a license of Your choice,  
which may contain terms different from this License, provided that You  
are in compliance with the terms of this License and that the license for  
the Executable form does not attempt to limit or alter the recipient’s  
rights in the Source Code form from the rights set forth in this License. If  
You distribute the Covered Software in Executable form under a different  
license, You must make it absolutely clear that any terms which differ  
from this License are offered by You alone, not by the Initial Developer or  
Contributor. You hereby agree to indemnify the Initial Developer and  
every Contributor for any liability incurred by the Initial Developer or such  
Contributor as a result of any such terms You offer.  
6.3. In the event of termination under Sections 6.1 or 6.2 above, all end  
user licenses that have been validly granted by You or any distributor  
hereunder prior to termination (excluding licenses granted to You by any  
distributor) shall survive termination.  
7. LIMITATION OF LIABILITY.  
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY,  
WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR  
OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER  
CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED SOFTWARE,  
OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY  
PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR  
3.6. Larger Works.  
You may create a Larger Work by combining Covered Software with  
other code not governed by the terms of this License and distribute the  
Larger Work as a single product. In such a case, You must make sure  
the requirements of this License are fulfilled for the Covered Software.  
CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING,  
WITHOUT LIMITATION, DAMAGES FOR LOST PROFITS, LOSS OF  
GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR  
MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES  
OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED  
OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF  
LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR  
PERSONAL INJURY RESULTING FROM SUCH PARTY’S  
4. Versions of the License.  
4.1. New Versions.  
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH  
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE  
Sun Microsystems, Inc. is the initial license steward and may publish  
revised and/or new versions of this License from time to time. Each  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY  
TO YOU.  
your documentation that you have used the FreeType code. (`credits’)  
We specifically permit and encourage the inclusion of this software, with  
or without modifications, in commercial products. We disclaim all  
warranties covering The FreeType Project and assume no liability related  
to The FreeType Project.  
Finally, many people asked us for a preferred form for a credit/disclaimer  
to use in compliance with this license. We thus encourage you to use  
the following text:  
8. U.S. GOVERNMENT END USERS.  
The Covered Software is a “commercial item,” as that term is defined in  
48 C.F.R. 2.101 (Oct. 1995), consisting of “commercial computer  
software” (as that term is defined at 48 C.F.R. 252.227-7014(a)(1)) and  
“commercial computer software documentation” as such terms are  
used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.  
12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all  
U.S. Government End Users acquire Covered Software with only those  
rights set forth herein. This U.S. Government Rights clause is in lieu of,  
and supersedes, any other FAR, DFAR, or other clause or provision that  
addresses Government rights in computer software under this License.  
“Portions of this software are copyright © 1996-2002 The FreeType  
Project (www.freetype.org). All rights reserved.”  
Legal Terms  
===========  
9. MISCELLANEOUS.  
1. Definitions  
This License represents the complete agreement concerning subject  
matter hereof. If any provision of this License is held to be  
--------------  
unenforceable, such provision shall be reformed only to the extent  
necessary to make it enforceable. This License shall be governed by the  
law of the jurisdiction specified in a notice contained within the Original  
Software (except to the extent applicable law, if any, provides  
Throughout this license, the terms `package’, `FreeType Project’, and  
`FreeType archive’ refer to the set of files originally distributed by the  
authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the  
`FreeType Project’, be they named as alpha, beta or final release.  
`You’ refers to the licensee, or person using the project, where `using’ is  
a generic term including compiling the project’s source code as well as  
linking it to form a `program’ or `executable’. This program is referred to  
as `a program using the FreeType engine’.  
This license applies to all files distributed in the original FreeType Project,  
including all source code, binaries and documentation, unless otherwise  
stated in the file in its original, unmodified form as distributed in the  
original archive. If you are unsure whether or not a particular file is  
covered by this license, you must contact us to verify this.  
The FreeType Project is copyright (C) 1996-2000 by David Turner,  
Robert Wilhelm, and Werner Lemberg. All rights reserved except as  
specified below.  
otherwise), excluding such jurisdiction’s conflict-of-law provisions. Any  
litigation relating to this License shall be subject to the jurisdiction of the  
courts located in the jurisdiction and venue specified in a notice  
contained within the Original Software, with the losing party responsible  
for costs, including, without limitation, court costs and reasonable  
attorneys’ fees and expenses. The application of the United Nations  
Convention on Contracts for the International Sale of Goods is expressly  
excluded. Any law or regulation which provides that the language of a  
contract shall be construed against the drafter shall not apply to this  
License. You agree that You alone are responsible for compliance with  
the United States export administration regulations (and the export  
control laws and regulation of any other countries) when You use,  
distribute or otherwise make available any Covered Software.  
10. RESPONSIBILITY FOR CLAIMS.  
As between Initial Developer and the Contributors, each party is  
responsible for claims and damages arising, directly or indirectly, out of  
its utilization of rights under this License and You agree to work with  
Initial Developer and Contributors to distribute such responsibility on an  
equitable basis. Nothing herein is intended or shall be deemed to  
constitute any admission of liability.  
2. No Warranty  
--------------  
THE FREETYPE PROJECT IS PROVIDED `AS IS’ WITHOUT WARRANTY  
OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT  
LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS  
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED  
BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.  
--------------------------------------------------------------------  
NOTICE PURSUANT TO SECTION 9 OF THE COMMON  
DEVELOPMENT AND DISTRIBUTION LICENSE (CDDL)  
3. Redistribution  
For Covered Software in this distribution, this License shall be governed  
by the laws of Germany (excluding conflict-of-law provisions).  
-----------------  
Any litigation relating to this License shall be subject to the jurisdiction  
This license grants a worldwide, royalty-free, perpetual and irrevocable  
right and license to use, execute, perform, compile, display, copy, create  
derivative works of, distribute and sublicense the FreeType Project (in  
both source and object code forms) and derivative works thereof for any  
purpose; and to authorize others to exercise some or all of the rights  
granted herein, subject to the following conditions:  
and the courts of Berlin Germany, with venue lying in Berlin Germany.  
The FreeType Project LICENSE  
----------------------------  
2002-Apr-11  
o Redistribution of source code must retain this license file (`FTL.TXT’)  
unaltered; any additions, deletions or changes to the original files must  
be clearly indicated in accompanying documentation. The copyright  
notices of the unaltered, original files must be preserved in all copies  
of source files.  
Copyright 1996-2002 by  
David Turner, Robert Wilhelm, and Werner Lemberg  
Introduction  
o Redistribution in binary form must provide a disclaimer that states that  
the software is based in part of the work of the FreeType Team, in the  
distribution documentation. We also encourage you to put an URL to  
the FreeType web page in your documentation, though this isn’t  
mandatory.  
============  
The FreeType Project is distributed in several archive packages; some of  
them may contain, in addition to the FreeType font engine, various tools  
and contributions which rely on, or relate to, the FreeType Project.  
This license applies to all files found in such packages, and which do  
not fall under their own explicit license. The license affects thus the  
FreeType font engine, the test programs, documentation and makefiles,  
at the very least.  
These conditions apply to any software derived from or based on the  
FreeType Project, not just the unmodified files. If you use our work, you  
must acknowledge us. However, no fee need be paid to us.  
4. Advertising  
--------------  
This license was inspired by the BSD, Artistic, and IJG (Independent  
JPEG Group) licenses, which all encourage inclusion and use of free  
software in commercial and freeware products alike. As a consequence,  
its main points are that:  
Neither the FreeType authors and contributors nor you shall use the  
name of the other for commercial, advertising, or promotional purposes  
without specific prior written permission.  
• We don’t promise that this software works. However, we will be  
We suggest, but do not require, that you use one or more of the  
following phrases to refer to this software in your documentation or  
advertising materials: `FreeType Project’, `FreeType Engine’, `FreeType  
library’, or `FreeType Distribution’.  
interested in any kind of bug reports. (`as is’ distribution)  
• You can use this software for whatever you want, in parts or full form,  
without having to pay us. (`royalty-free’ usage)  
• You may not pretend that you wrote this software. If you use it, or  
only parts of it, in a program, you must acknowledge somewhere in  
Download from Www.Somanuals.com. All Manuals Search And Download.  
As you have not signed this license, you are not required to accept it.  
However, as the FreeType Project is copyrighted material, only this  
license, or another one contracted with the authors, grants you the right  
to use, distribute, and modify it. Therefore, by using, distributing, or  
modifying the FreeType Project, you indicate that you understand and  
accept all the terms of this license.  
License is also granted to make and use derivative works provided that  
such works are identified as “derived from the RSA Data Security, Inc.  
MD5 Message-Digest Algorithm” in all material mentioning or  
referencing the derived work.  
RSA Data Security, Inc. makes no representations concerning either the  
merchantability of this software or the suitability of this software for any  
particular purpose. It is provided “as is” without express or implied  
warranty of any kind.  
5. Contacts  
-----------  
These notices must be retained in any copies of any part of this  
documentation and/or software.  
There are two mailing lists related to FreeType:  
o [email protected]  
Discusses general use and applications of FreeType, as well as future  
and wanted additions to the library and distribution. If you are looking for  
support, start in this list if you haven’t found anything to help you in the  
documentation.  
The MIT License  
Copyright 2008 Jeffrey Powers for Fluxcapacity Open Source.  
Copyright 2011, John Resig  
Copyright 2005-2009 Sam Stephenson  
o [email protected]  
Permission is hereby granted, free of charge, to any person obtaining a  
copy of this software and associated documentation files (the  
“Software”), to deal in the Software without restriction, including without  
limitation the rights to use, copy, modify, merge, publish, distribute,  
sublicense, and/or sell copies of the Software, and to permit persons to  
whom the Software is furnished to do so, subject to the following  
conditions:  
Discusses bugs, as well as engine internals, design issues, specific  
licenses, porting, etc.  
o http://www.freetype.org  
Holds the current FreeType web page, which will allow you to download  
our latest development version and read online documentation.  
The above copyright notice and this permission notice shall be included  
You can also contact us individually at: David Turner {david.turner@  
freetype.org} Robert Wilhelm {[email protected]} Werner  
in all copies or substantial portions of the Software.  
LReSmAbeMrg D{w4ernoerr.lMemDbe5rgM@feresestyapge.eor-gD} igest Algorithm  
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF  
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO  
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT  
SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR  
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN  
ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,  
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE  
OR OTHER DEALINGS IN THE SOFTWARE.  
License  
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights  
reserved.  
License to copy and use this software is granted provided that it is  
identified as the “RSA Data Security, Inc. MD5 Message-Digest  
Algorithm” in all material mentioning or referencing this software or this  
function.  
Some software components of this product incorporate source code covered under the BSD license as follows.  
Component Name  
License  
License URL  
lighttpd 1.4.26  
BSD 2.0  
http://www.opensource.org/licenses/bsd-license.html  
lighttpd is a secure, fast, compliant, and very flexible webserver that has been optimized for high-performance environments. It has a very low  
memory footprint compared to other webservers and takes care of cpuload.  
Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression,  
URL-Rewriting and many more) make lighttpd the perfect webserver-  
software for every server that suffers load problems.  
contributors may be used to endorse or promote products derived  
from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
FCoor mpyorreigadhdtit(iocn)a2l in0f0or4m,aKtionne, ssecndhkeme,aiilntochreelpm.cectnv@taslamsung.com.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met :  
• Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
• Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
• Neither the name of the ‘incremental’ nor the names of its  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Component Name  
License  
License URL  
librtp 1.20  
BSD 2.0  
http://www.opensource.org/licenses/bsd-license.html  
FCoor mpyorreigadhdtit(iocn)a1l in9f9or8m-a2ti0on0,0seUndneivmearilstoithyelCp.occltlve@gseamLsounngd.coonm.  
4. Neither the name of the University nor of the Department may be  
used to endorse or promote products derived from this software  
without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESSED OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,  
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, is permitted provided that the following conditions are met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
3. All advertising materials mentioning features or use of this software  
must display the following acknowledgement: This product includes  
software developed by the Computer Science Department at  
University College London  
Component Name  
License  
License URL  
net-snmp-5.4.1  
BSD  
http://www.net-snmp.org/about/license.html  
Simple Network Management Protocol (SNMP) is an Internetstandard  
protocol for managing devices on IP networks. It is used mostly in  
network management systems to monitor the devices attached to the  
network for conditions that need administrative attention. Net-SNMP is a  
suite of applications used to implement SNMP v1, SNMP v2c and  
SNMP v3 using both IPv4 and IPv6.  
3. Neither the name of the Networks Associates Technology, Inc nor the  
names of its contributors may be used to endorse or promote  
products derived from this software without specific prior written  
permission.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
For more additional information, send email to [email protected].  
Various copyrights apply to this package, listed in various separate parts  
below. Please make sure that you read all the parts.  
Part 1: CMU/UCD copyright notice: (BSD like)  
Copyright 1989, 1991, 1992 by Carnegie Mellon University  
Derivative Work - 1996, 1998-2000  
Copyright 1996, 1998-2000 The Regents of the University of California  
All Rights Reserved  
Permission to use, copy, modify and distribute this software and its  
documentation for any purpose and without fee is hereby granted,  
provided that the above copyright notice appears in all copies and that  
both that copyright notice and this permission notice appear in  
supporting documentation, and that the name of CMU and The  
Regents of the University of California not be used in advertising or  
publicity pertaining to distribution of the software without specific written  
permission.  
Part 3: Cambridge Broadband Ltd. copyright notice  
(BSD)  
Portions of this code are copyright (c) 2001-2003, Cambridge  
Broadband Ltd.  
All rights reserved.  
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA  
DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,  
INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE  
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL,  
INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES  
WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR  
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE  
OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN  
CONNECTION WITH THE USE OR PERFORMANCE OF THIS  
SOFTWARE.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. The name of Cambridge Broadband Ltd. may not be used to  
endorse or promote products derived from this software without  
specific prior written permission.  
Part 2: Networks Associates Technology, Inc  
copyright notice (BSD)  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS  
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
Copyright (c) 2001-2003, Networks Associates Technology, Inc  
All rights reserved.  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE  
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER  
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT  
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS  
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT  
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY  
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGE.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
Part 4: Sun Microsystems, Inc. copyright notice  
(BSD)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Copyright © 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa  
Clara, California 95054, U.S.A.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
All rights reserved.  
Use is subject to license terms below. This distribution may include  
materials developed by third parties. Sun, Sun Microsystems, the Sun  
logo and Solaris are trademarks or registered trademarks of Sun  
Microsystems, Inc. in the U.S. and other countries. Redistribution and  
use in source and binary forms, with or without modification, are  
permitted provided that the following conditions are met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of the Sun Microsystems, Inc. nor the names of its  
contributors may be used to endorse or promote products derived  
from this software without specific prior written permission.  
Part 7: Fabasoft R&D Software GmbH & Co KG  
copyright notice (BSD)  
Copyright (c) Fabasoft R&D Software GmbH & Co KG, 2003  
[email protected]  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
Author: Bernhard Penz  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. The name of Fabasoft R&D Software GmbH & Co KG or any of its  
subsidiaries, brand or product names may not be used to endorse or  
promote products derived from this software without specific prior  
written permission.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS  
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
Part 5: Sparta, Inc copyright notice (BSD)  
Copyright (c) 2003-2009, Sparta, Inc  
All rights reserved.  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE  
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER  
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT  
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS  
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT  
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY  
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGE.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of Sparta, Inc nor the names of its contributors may  
be used to endorse or promote products derived from this software  
without specific prior written permission.  
Part 8: Apple Inc. copyright notice (BSD)  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
Copyright (c) 2007 Apple Inc.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of Apple Inc. (“Apple”) nor the names of its  
contributors may be used to endorse or promote products derived  
from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS CONTRIBUTORS  
“AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
Part 6: Cisco/BUPTNIC copyright notice (BSD)  
Copyright (c) 2004, Cisco, Inc and Information Network Center of  
Beijing University of Posts and Telecommunications.  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE  
ARE DISCLAIMED. IN NO EVENT SHALL APPLE OR  
All rights reserved.  
ITSCONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL  
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF  
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND  
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT  
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN  
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of Cisco, Inc, Beijing University of Posts and  
Telecommunications, nor the names of their contributors may be  
used to endorse or promote products derived from this software  
without specific prior written permission.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
Part 9: ScienceLogic, LLC copyright notice (BSD)  
Copyright (c) 2009, ScienceLogic, LLC  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions  
aremet:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of ScienceLogic, LLC nor the names of its  
contributors may be used to endorse or promote products derived  
from this software without specific prior written permission.  
Component Name  
License  
License URL  
miniupnpc 1.5  
BSD 2.0  
http://miniupnp.free.fr/  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE  
COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
FCoor mpyorreigadhdtit(iocn)a2l in0f0or5m-a2ti0on0,9se,nTdheommailatoshBelpE.cRcNtv@AsRamDsung.com.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. The name of the author may not be used to endorse or promote  
products derived from this software without specific prior written  
permission.  
Component Name  
License  
License URL  
ppp 2.4.5  
BSD 2.0  
http://packages.debian.org/changelogs/pool/main/p/ppp/ppp_2.4.5-5.1/  
ppp-udeb.copyright  
1. Redistributions of source code must retain the above copyright notice,  
FCoor mpyorreigadhdtit(iocn)a2l in0f0or3maPtiaonu,lsMendacemkaeilrtroahse.[email protected].  
this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
3. The names of the authors of this software must not be used to  
endorse or promote products derived from this software without prior  
written permission.  
1. Redistributions of source code must retain the above copyright  
4. Redistributions of any form whatsoever must retain the following  
acknowledgment: “This product includes software developed by  
Pedro Roque Marques <[email protected]>”  
notice, this list of conditions and the following disclaimer.  
2. The name(s) of the authors of this software must not be used to  
endorse or promote products derived from this software without prior  
written permission.  
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN  
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS  
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR  
PERFORMANCE OF THIS SOFTWARE.  
3. Redistributions of any form whatsoever must retain the following  
acknowledgment: “This product includes software developed by Paul  
Mackerras <[email protected]>”.  
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN  
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS  
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR  
PERFORMANCE OF THIS SOFTWARE.  
Copyright (c) 1995 Eric Rosenquist.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
Copyright (c) 1995 Pedro Roque Marques.  
1. Redistributions of source code must retain the above copyright notice,  
All rights reserved.  
this list of conditions and the following disclaimer.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. The name(s) of the authors of this software must not be used to  
Download from Www.Somanuals.com. All Manuals Search And Download.  
endorse or promote products derived from this software without prior  
written permission.  
Copyright (c) 1999 Tommi Komulainen.  
All rights reserved.  
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN  
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS  
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR  
PERFORMANCE OF THIS SOFTWARE.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright notice,  
this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
Copyright (c) 2002 Google, Inc.  
3. The name(s) of the authors of this software must not be used to  
endorse or promote products derived from this software without prior  
written permission.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
4. Redistributions of any form whatsoever must retain the following  
acknowledgment: “This product includes software developed by  
Tommi Komulainen <To[email protected]>”.  
1. Redistributions of source code must retain the above copyright notice,  
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN  
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS  
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR  
PERFORMANCE OF THIS SOFTWARE.  
this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. The name(s) of the authors of this software must not be used to  
endorse or promote products derived from this software without prior  
written permission.  
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN  
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS  
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR  
PERFORMANCE OF THIS SOFTWARE.  
Copyright (c) 1984-2000 Carnegie Mellon University.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright notice,  
this list of conditions and the following disclaimer.  
Copyright (c) 2001 by Sun Microsystems, Inc.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
All rights reserved.  
Non-exclusive rights to redistribute, modify, translate, and use this  
software in source and binary forms, in whole or in part, is hereby  
granted, provided that the above copyright notice is duplicated in any  
source form, and that neither the name of the copyright holder nor the  
author is used to endorse or promote products derived from this  
software.  
3. The name “Carnegie Mellon University” must not be used to endorse  
or promote products derived from this software without prior written  
permission. For permission or any legal details, please contact Office  
of Technology Transfer Carnegie Mellon University 5000 Forbes  
Avenue Pittsburgh, PA 15213-3890 (412) 268-4387, fax: (412)  
268-7395 [email protected]  
THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT ANY EXPRESS  
OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE  
IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A  
PARTICULAR PURPOSE.  
4. Redistributions of any form whatsoever must retain the following  
acknowledgment: “This product includes software developed by  
Computing Services at Carnegie Mellon University (http://www.cmu.  
edu/computing/).”  
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES  
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT  
SHALL CARNEGIE MELLON UNIVERSITY BE LIABLE FOR ANY  
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY  
DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA  
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,  
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR  
IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS  
SOFTWARE.  
Component Name  
License  
License URL  
hdparm-9.39  
BSD-License  
http://www.opensource.org/licenses/bsd-license.html  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE  
COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
Copyright (c) 2008 Mark Lord  
All rights reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are  
met:  
1. Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. Neither the name of the copyright holder nor the names of its  
contributors may be used to endorse or promote products derived  
from this software without specific prior written permission.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Samsung Techwin respeta el medio ambiente durante todo el proceso de fabricación de sus productos y realiza una serie de  
procedimientos orientados a ofrecer productos ecológicos.  
El símbolo Eco representa el compromiso de Samsung Techwin de fabricar productos que respeten el medio ambiente e indica a la vez  
que este equipo cumple con la Directiva de la Unión Europea EU RoHS.  
(Waste Electrical & Electronic Equipment)  
Correct Disposal of This Product  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB  
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment  
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly  
to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased this product, or their local government office, for details of  
where and how they can take these items for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic  
accessories should not be mixed with other commercial wastes for disposal.  
Correct disposal of batteries in this product  
(Applicable in the European Union and other European countries with separate battery return systems.)  
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their  
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive  
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.  
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery  
return system.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SALES NETWORK  
SAMSUNG TECHWIN CO., LTD.  
Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea  
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745  
SAMSUNG TECHWIN AMERICA Inc.  
SAMSUNG TECHWIN EUROPE LTD.  
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660  
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920  
Fax : +1-201-373-0124  
Samsung House, 1000 Hillswood Drive, Hillswood Business  
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS  
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325  
www.samsungcctvusa.com  
www.samsungtechwin.com  
www.samsungsecurity.com  
www.samsungipolis.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Portable CD Player 14 518 User Guide
Radio Shack Range 22 218 User Guide
Rolls Network Card PB23 User Guide
Saab Automobile 5 Sep User Guide
Samsung Digital Camera TL210 User Guide
Samsung Projector SP M20 User Guide
Samsung Range DG68 00294A User Guide
Sanyo Plumbing Product MTS 2000 User Guide
Sears Trimmer 31679197 User Guide
Sennheiser Bluetooth Headset EZX 60 User Guide