Samsung DVD Player C01 User Guide

SiPTel C01 IP Phone User Manual  
SiPTel C01  
IP Phone  
5.2E version  
User Manual 3.1.00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
TABLE OF CONTENTS  
1. INTRODUCTION  
1.1. Overview  
1.2. Features  
1.3. Specification  
1.4. Structure of SiPTel IP Phone  
1.4.1. Keypad  
1.4.2. LCD Display  
1.4.3. LED Display  
1.4.4. Port Structure  
2. PRE-INSTALLATION CHECK LIST  
2.1. Power Requirements  
2.2. Component Check List  
2.3. User Requirements  
3. INSTALLATION & INSTRUCTIONS  
3.1. Connecting Cables  
3.2. Booting Up process  
3.3. Keying Instructions  
4. GETTING STARTED WITH MENU  
4.1. Call Log  
4.1.1. Received Calls  
4.1.2. Dialed Calls, Missed Calls, Tx / Rx Calls  
4.1.3. Delete All  
4.2. Phone Book  
4.2.1. Find Number  
4.2.2. Add  
4.2.3. Memory Dial  
4.2.4. Delete All  
4.3. Ring/Volume  
4.3.1. Ring Selection  
4.3.2. Ringing tone Volume  
4.4. Setup  
4.4.1. My Phone  
4.4.2. Network  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.4.3. Call Setup  
4.4.4. Modem  
4.4.4.1. Call Options  
4.4.5. Time  
4.4.6. PSTN  
4.4.7. HTTP PROXY  
4.5. Information  
4.5.1. Network  
4.5.2. Version  
4.6. BALANCE  
4.7. Reboot  
5. USING SIPTEL IP PHONE  
5.1. Connecting IP Phone to Internet  
5.1.1. Using in Dialup Mode  
5.1.2. Using with Broadband Cable  
5.2. Making a VoIP Call  
5.2.1. In On-Hook mode (Pre-dial)  
5.2.2. In Off Hook mode  
5.3. Making a PSTN Call  
5.4. Making a call in Phone Book mode  
5.5. Making a call from Call Log mode  
5.6. Memory Dial  
5.7. Web Access  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
1. INTRODUCTION  
1.1. Overview  
The SiPTel IP Phone is a single user VoIP (Voice over Internet Protocol) phone for the home or small-  
medium size businesses. The SiPTel IP Phone supports ITU-T H.323 protocol for voice communication on  
data lines. It is a stand-alone device, which means no PC connection is required to use it. The SiPTel IP  
Phone allows user to make long distance call or international call at low cost. Using the standard protocol,  
SiPTel IP Phone can interoperate with most Internet devices for communication over the Internet.  
1.2. Features  
• Easy to use, simple to activate  
• VAD (Voice Activity Detection)  
• Volume control separate for both PSTN and VoIP calls  
• Three Speed Dialing keys  
•100 numbers storage Phone book  
• Last number redial for both PSTN and VoIP  
• 4 line Graphic LCD display  
• Call Mute  
• Silence Suppression  
• Echo Cancellation  
• Excellent voice quality DSP technology  
• Network management with SNMP-based NMS  
• Software updates/upgrades via remote access  
• Configurable phone number assignment to match dial plan  
• Remote management via SNMP, Telnet and HTTP  
1.3. Specification  
LAN Interface Standards  
IEEE 802.3  
Supports Static, DHCP, PPPoE  
Dial-up Interface  
• Data Rates from 300 bps to 56k bps.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
• Data Modulation Standards V.90, V.34, V.432bis, V.22bis, V.22, V.23, V.21 and V.23 reversible  
(Minitel), Bell 212, Bell 103 Dialup Modem V.42 Error Control  
• Country Code support  
• V.42 Error Control  
• V.42bis Compression  
• Protected Against Surge and Over voltage on the Telephone Line  
Configuration Management  
Telnet, RS-232, Http, LCD display  
Protocol & Codec Specifications  
Protocol : ITU H.323 v4, H.225, H.245  
Codec : ITU G.711, G.729.A, G.723.1  
Power  
5VDC, 2A  
Dimensions  
14cm W × 4.3cm H × 17.5cm D  
Weight  
0.73kg  
Operating Temperature  
32oF to 131oF (0oC to 55oC)  
Operating Humidity  
10% to 85% no condensing.  
Storage Temperature  
32oF to 149oF (0oC to 65oC)  
Storage Humidity  
5% to 90% non condensing  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
1.4. Structure of SiPTel IP Phone  
1.4.1. Keypad  
Figure 1) Keypad Structure of SiPTel IP Phone  
The description for each key is as follows.  
Key name  
Description  
Menu  
Ÿ Used to initiate the menu on LCD  
Ÿ Used to change between preferences when entering characters (English-  
capital and lowercase / numerical / special characters).  
Ÿ Memory dial  
M1~M3  
DEL  
Ÿ Used to delete the characters in Pre-dial and Phone Book mode.  
Ÿ Used to move up the cursor to select menu.  
Ÿ Used to move down the cursor to select menu.  
Ÿ Used to move the cursor to the right in Phone Book mode.  
Ÿ Used to initiate the Call Log menu in off hook mode.  
Call Log  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
ƒ P-Book  
Ÿ Used to move the cursor to the left in Phone Book mode.  
Ÿ Used to initiate the Phone Book menu.  
OK  
Ÿ Used to complete the input in Phone Book menu.  
Ÿ Used to confirm the entered or selected settings.  
Ÿ Used to cancel the selected menu, entered data, or etc.  
Ÿ Used to place the PSTN call.  
Cancel  
PSTN  
MUTE  
Ÿ Used to make the voice not to be heard from the counterpart.  
Ÿ Used to connect to dial-up ISP. (Option).  
@ISP  
VOL + / -  
FLASH  
Ÿ Used to adjust the volume of the handset  
Ÿ Used to place another call by droping the current call while dialing or in  
the middle of a connected call. (Available only in PSTN mode).  
Ÿ Used to redial the number last dialed  
REDIAL  
Speaker  
Ÿ Used to carry on the call without picking up the handset. Press again to  
turn off the speaker phone  
1.4.2. LCD Display  
SIPTEL  
10100-1000  
A12:00  
The LCD screen shows the current status of the SiPTel IP Phone, menu options on the LCD screen,  
Telephone number dialed or received etc. (4x15)  
First Line  
Status display – displays the present state of the IP Phone.  
Name display – displays the name entered by the user.  
Telephone number display – displays number entered using keypad.  
Current time display  
Second Line  
Third Line  
Fourth Line  
The following are icons used to display the present state of the IP Phone  
Icon  
Name  
Function  
Displays the DNS status.  
DNS Status  
Gatekeeper  
Flashing : Finding the DNS server  
Constant : Could reach the IP Address of the DNS  
Displays the G/K registration status.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
Status  
Flashing : Trying to find the Gatekeeper.  
Constant : Registered with Gatekeeper successfully.  
Call status  
display  
: Displayed when the call is connected successfully.  
: Displayed when the call isn’t connected.  
: Static IP  
: DHCP  
: PPPoE  
Kinds of  
connection  
Mute  
Ÿ Displayed when using Mute function.  
Flash save  
display  
Ÿ Displayed when data is being saved in memory  
Ÿ Displayed when the SiPTel IP Phone is connected to the Internet  
thru Ethernet cable.  
Ethernet  
Ÿ Displayed when the SiPTel IP Phone is connected to Internet thru  
the Modem.  
Modem  
Summer Time  
Ÿ Displayed when the summer time is applied.  
Ÿ Displays the input mode.  
: Symbols  
Entry mode  
: English Lower Case  
: English Capital  
: Numeric  
Ÿ Displayed only when the navigation key is available for menu  
selection.  
Navigation key  
1.4.3. LED Display  
PSTN  
@ISP  
Ÿ Glows when using PSTN mode.  
Ÿ Glows when using Dial-up connection.  
1.4.4. Port Structure  
POWER  
§
§
Use to connect to the power adapter.  
ETHERNET  
Use to connect to Internet leased line, cable modem, ADSL Modem, or etc. for  
internet connection.  
LINE  
§
Use to connect to the regular telephone line.  
Figure 2) SiPTel IP Phone Rear Panel  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
2. PRE-INSTALLATION CHECK LIST  
2.1. Power Requirements  
§
§
§
AC Voltage : External power adapter (100V-240V, 50/60Hz).  
Please use only the power adapter provided with the SiPTel IP Phone.  
For additional power adapter, please ask your product provider.  
Safety  
Should liquid or solid object get into the cabinet, unplug the unit and have it checked by the  
qualified personnel before operating it any further.  
To disconnect the cord, pull it out by the plug. Never pull the cord itself.  
Do not place the unit in surfaces (rugs, blankets, etc.) or near materials (curtains, draperies)  
that may block the ventilation holes.  
Installation  
Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust  
or mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water  
may damage the unit.  
Cleaning  
Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use  
strong solvents such s thinner or benzene as they might damage the finish of the unit.  
2.2. Component Check List  
Open the box of SiPTel IP Phone and make sure all the components are included in the box. The  
following is the pictures of SiPTel IP Phone components. The picture can be different with the actually  
models of SiPTel IP Phone.  
SiPTel IP Phone - 1  
Handset - 1  
Power adaptor - 1  
User Manual - 1  
Coiled Cord - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
2.3. User Requirements  
Before you start, please ask your local ISP or network administrator for an Internet account from  
User  
ISP Requirement  
IP address  
Gateway  
Common  
Static IP User  
Subnet mask  
DNS  
§
§
H.323 ID  
E.164 Number  
DHCP User  
PPPoE User  
User ID  
Password  
Dial-up User  
ISP Telephone number  
User name  
Password  
3. INSTALLATION & INSTRUCTIONS  
3.1. Connecting Cables  
STEP 1  
Connect the Ethernet line that came from the Internet leased line, cable modem, or ADSL  
modem to the Ethernet port of the SiPTel IP Phone.  
STEP 2  
STEP 3  
(Option) Connect the PSTN line to the PSTN port of the SiPTel IP Phone.  
Connect the power port to the power source with a power adaptor.  
3.2. Booting Up process  
STEP 1  
If the cable connection is completed properly, the SiPTel IP Phone will start booting  
automatically.  
*************************  
SYSTEM ON START  
INITIALIZING  
Wait for a while till the rebooting is completed.  
*************************  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
If the booting is completed properly, the following display will appear.  
You can see some Icons, Brand Name, ITSP given VoIP Phone  
Number, Time, etc.  
SiP Tel  
10100-1000  
A12:00  
3.3. Keying Instructions  
Some setup menus support a few character input mode, English lower-case, English capital, numeric,  
and special characters or symbols. In an input mode, if you press ‘Menu’ key, the input mode will be  
toggled to another one in order. For example, the input mode will be changed from : English lower-case  
to : English-capital or to : Numerical and to : Special characters in order.  
When you enter name into the input line, please use the navigation key on the key pad to move to the left  
or right in the input line. Use ‘Delete’ key to delete the characters or numeric, and the cursor will move to  
the left erasing the character.  
When you enter the phone number in the input line, press ‘Menu’ key until you can see the  
top right.  
icon on the  
When you enter the special characters into the input line, please press ‘Menu’ key until you can see the  
icon on the right of the first line. Please use ‘0’ key on the keypad to select the desired special character.  
For English characters, press the number key corresponding to the alphabet more than once till  
you can get the desired alphabet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4. GETTING STARTED WITH MENU  
4.1. Call Log  
This menu allows user to look up the Dialed, Received and Missed calls list. User can look up the call lists  
up to 100 lists. User can make a call by using this call logs, and delete them when not required.  
4.1.1. Rcvd Calls  
STEP 1  
STEP 2  
Press “Menu” key on the keypad in on-hook mode.  
Select “1: Call Log”.  
Press ‘OK’ button or press the menu number to select the menu  
<Menu>  
1:Call Log  
2: Phone Book  
Or Press ‘Cancel’ key to move to the upper menu.  
STEP 3  
Select ‘1: Rcvd Calls’.  
Press ‘OK’ button or select ‘1’ key.  
<Call Log>  
1:Rcvd Calls  
2: Dialed Calls  
STEP 4  
Select the desired phone number in the received call lists and press ‘OK’ button to view  
the details of the selected number.  
Or Press ‘Cancel’ key to move to the previous screen.  
Rcvd Calls [ 2/20]  
03034  
03034  
STEP 5  
User the left and right arrow key to get more information.  
Press ‘Cancel’ button to move to the previous screen.  
No Entry  
03034  
Date:10/16(SUN)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 6  
You can see the information such as the Caller Name if exists a phone book entry for that  
number, Date [Date/Month(day)], Time, etc.,  
Press ‘Cancel’ button to move to the previous screen.  
No Entry  
03034  
Time : 08:04A  
STEP 7  
Last information is Call duration in minutes [HH:MM].  
Press ‘Cancel’ button to move to the previous screen.  
No Entry  
03034  
Duration : [08:37]  
STEP 8  
You can press DELETE button anytime in the above views, and select Delete from ‘VIEW  
/ DELETE’ options displayed on top of the LCD screen, to delete that entry from the list.  
The deleted call list can’t be recovered. Please make sure whether it  
is ok to delete the call list before you delete call list. Please be sure  
doing so.  
Delete  
call list ?  
YES NO  
Press ‘Cancel’ button to move to the previous screen.  
4.1.2. Dialed , Missed , Tx/Rx Calls  
The options for Dialed Calls, Missed Calls and Tx/Rx ( both dialed and received calls ) which follows ‘1.  
RCVD Calls’ option will all be same as RCVD Calls options.  
4.1.3. Delete All  
STEP 1  
Select ‘1. Call log’ -> ‘5. Delete All’ after pressing MENU button  
Press ‘OK’ button or select menu number key.  
<Call Log>  
4: Tx/Rx Calls  
5: Delete All  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select Received or Transmitted ( Dialed ) that you want to clear from list.  
Press ‘Cancel’ button to move to the previous screen.  
<Delete All>  
1. Received  
2. Transmitted  
STEP 3  
Deleting all the options requires the authentication.  
Enter your user password.  
Enter Password  
Press ‘Cancel’ button to move to the previous screen.  
STEP 4  
Confirm to delete the selected group of numbers.  
Use the left or right arrow key to select ‘Yes / No’.  
Press ‘Cancel’ button to move to the previous screen.  
Delete all  
calling no ?  
YES NO  
4.2. Phone Book  
Phone Book is used to save and find the contacts in the memory of the phone. User can also use the  
menu to make a call after finding the destination phone number in the phone book.  
The phone book menu supports several character input mode as explained under  
“3.3. Keying Instructions”  
4.2.1. Find Number  
User can find phone numbers either by index or name. Index means the registered address of the  
memory.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.2.1.1. Find the number by Index  
STEP 1  
Select ‘1: Find Number’ to find the telephone number registered in the phone book.  
Use the navigation key or press the menu number to select the  
<PHONE BOOK>  
1: Find Number  
menu, and press ‘OK’ button.  
Press ‘Cancel’ key to move to the upper menu.  
2: Add  
STEP 2  
Select ‘By Index’.  
Use the navigation key or press the menu number to select the  
menu, and press ‘OK’ button.  
<Find Number>  
1 : By Index  
2 : By Name  
Press ‘Cancel’ key to move to the upper menu.  
STEP 3  
Enter the desired Index number, and press ‘OK’ button.  
Press ‘Cancel’ key to move to the upper menu.  
By Index  
4
STEP 4  
The telephone number and name corresponding to the Index number will be displayed.  
Press ‘Cancel’ key to move to the upper menu.  
12345678901  
[04] Uncle  
STEP 5  
If you want to make a call to the phone number, just pick up the handset. The call will be  
made to the phone number.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.2.1.2. Find the number by Name  
STEP 1  
Select ‘1: Find Number’ to find a telephone number from the phone book.  
Use the navigation key or press the menu number to select the  
menu, and press ‘OK’ button.  
<PHONE BOOK>  
1: Find Number  
Press ‘Cancel’ key to move to the upper menu.  
2: Add  
STEP 2  
Select ‘By Name’  
Use the navigation key or press the menu number to select the  
menu, and press ‘OK’ button.  
<Find Number>  
1: By Index  
Press ‘Cancel’ key to move to the upper menu.  
2:By Name  
STEP 3  
Enter complete or initial part of the name to find, and press ‘OK’ button.  
Press ‘Cancel’ key to move to the upper menu.  
By Name  
Unc  
STEP 4  
The telephone number and name corresponding to the Index number will be displayed.  
Press ‘Cancel’ key to move to the upper menu.  
12345678901  
[04]Uncle  
STEP 5  
If you want to make a call to the phone number, just pick up the handset.  
The call will be made to the phone number.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.2.2. Add  
This menu is to register a new telephone number into the phone book of IP Phone. The phone numbers  
can be registered up to 100 numbers.  
STEP 1  
Select ‘2: ADD’ menu in PHONE BOOK menu selection.  
Use the navigation key and press OK or press the menu number to  
select the menu.  
<PHONE BOOK>  
1: Find Number  
2:ADD  
Press ‘Cancel’ key to move to the upper menu.  
STEP 2  
Enter the name, telephone number and the register number(Index). Use navigation key to  
move to the next item.  
Use the ‘Menu’ key to toggle the input mode.  
Press ‘Cancel’ key to return to the upper menu.  
<ADD>  
NAME:  
TEL:  
STEP 3  
If you entered the name, Tel number, and address properly, you can see the following  
display. If you have omitted to enter the name or phone number, you can see the  
messages such as “No number to save!” or “No name to save!” etc.  
Please wait till this display disappears.  
Saved!  
4.2.3. Memory Dial  
This menu is to register the frequently dialed telephone numbers in the memory of the  
SiPTel IP Phone under three memory keys, and use to make a call by pressing just the memory key  
preset.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 1  
Select ‘3: Memory Dial’ in the PHONE BOOK menu selection.  
Use navigations key and press OK or press the menu number to  
select the menu.  
<PHONE BOOK>  
2: ADD  
Press ‘Cancel’ key to return to the upper menu.  
3: Memory Dial  
STEP 2  
Select the menu related to which of the three single touch KEYs you want  
to use for a particular number  
Use navigations key and press OK to select the KEY.  
Press ‘Cancel’ key to return to the upper menu.  
<Memory Dial>  
M1: Empty  
M2: Empty  
STEP 3  
Select 2nd Option from the menu.  
Use navigations key and press OK or press the menu number to  
<Memory Dial:1>  
1: Hidden[Disable]  
select the menu.  
2: No [Empty]  
Press ‘Cancel’ key to return to the upper menu.  
STEP 4  
Enter the phone number that you want to use under that single touch KEY.  
Press ‘Cancel’ keys to return to the On-Hook display.  
Save Tel No.  
into M1  
12345678901  
STEP 5  
Anytime, lifting handset and pressing M1 or M2 or M3 under which you save the above  
phone number will cause Phone to dial that number.  
4.2.4. Delete All  
This menu is to delete the entire phone numbers registered at the phone book. But the memory dial  
numbers will not be deleted.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 1  
Select ‘4.Delete All‘ from PHONE BOOK menu after press MENU button.  
PHONE BOOK menu can be selected even by pressing ‘P-BOOK’  
button just besides CANCEL button.  
<PHONE BOOK>  
3: Memory Dial  
Use navigations key and press OK button or press the menu number  
to select the menu.  
4: Delete All  
STEP 2  
Authenticate yourself to delete entries by entering the passowrd and press ‘OK’ button  
You can press ‘Cancel’ key to return to the upper menu.  
Enter Password  
STEP 3  
Confirm the deletion once again by selecting YES, if you are sure.  
Select YES or NO using navigation keys and press OK.  
Delete all ?  
YES NO  
Pressing ‘Cancel’ key here is like selecting NO and return to the  
upper menu  
4.3. Ring/Volume  
This menu is used to select the ringing tone. Currently, three kinds of bell rings are available.  
STEP 1  
STEP 2  
Press ‘Menu’ key on the keypad of the SiPTel IP Phone.  
Select ‘3: Ring / Volume’ menu in the menu selection.  
User the navigation key or press the menu number to select the  
menu.  
<Menu>  
2: Phone Book:  
3: Ring/Volume  
Press ‘Cancel’ key to move to the upper menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.3.1. Ring Selection  
STEP 1  
Select ‘1: Ring Select’ menu in the RING/VOLUME menu.  
Use navigation key or press the menu number to select the number.  
Press ‘Cancel’ key to move to the previous display.  
<Ring/Volume>  
1: Ring Select  
2: Volume  
STEP 2  
The current ringing tone will be displayed in the second line of LCD. Select the preferred  
one of the three kinds of ringing tones.  
Use the navigation key to hear how they ring and press OK or press  
the number of the desired one to select the ringing tone.  
Press ‘Cancel’ key to return to the upper menu.  
<Ring Select 1>  
1: Ring 1  
2: Ring 2  
STEP 3  
If you selected the ringing tone, you can see the following display on LCD. Here, you will  
hear ringing tone repeatedly till you select ‘YES’ or ‘NO’  
Use navigation key to select ‘YES’ or ‘NO’.  
Select Ring1?  
YES NO  
Press ‘Cancel’ key to move to the upper menu without changing the  
ringing tone.  
4.3.2. Ringing tone Volume  
STEP 1  
Press ‘Volume’ menu under RING/VOLUME menu.  
Use navigation key or press the menu number to select the number.  
Press ‘Cancel’ key to move to the previous display.  
<Ring/Volume>  
1: Ring Select  
2: Volume  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Adjust the ringing tone volume. Use the navigation key to adjust the volume of the ring  
tone.  
Press ‘OK’ button to save the volume setting and to return to the  
upper menu.  
<Ring Volume>  
( - ) [ 11 ] (+)  
Press ‘Cancel’ key to return to the upper menu without adjusting the  
volume.  
4.4. Setup  
This section includes important but basic information for setting the SiPTel IP Phone. To setup the SiPTel  
IP Phone, you may need to input some characters or numbers into the input line. Please study the  
following instruction on key input prior to setup.  
Entering MENU with authentication password.  
STEP 1  
STEP 2  
Press ‘Menu’ key.  
Select ‘4. Setup’.  
Press 4 or select ‘4. Setup’ option using navigation keys and press  
OK.  
<Menu>  
4:Setup  
5. Information  
STEP 3  
Enter 0000 as password for user authentication which is default and press OK button.  
Press CANCEL button to quit from getting into MENU  
Enter Password  
4.4.1. My Phone  
4.4.1.1. User Password  
This menu is to change the user password used for SiPTel IP Phone Setup. Following are the options to  
change your current password.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 1  
Select ‘2: User PWD’ option under ‘My Phone’ Menu  
Press 2 or select ‘2. User PWD’ using navigation keys and press OK  
key.  
<My Phone>  
1: My Name  
2: User PWD  
STEP 2  
The icon  
will appear. Enter the new password. You can enter password up to 15 digits.  
Enter the current password, press OK key.  
Enter the new password, press OK key and re-enter the new  
password to confirm and then press ‘OK’ key again to save the new  
password  
User Password  
Pressing “Cancel’ key anytime before confirming password during  
the above steps to return to the upper menu without change.  
4.4.2. Network Setup  
4.4.2.1. Mode Select  
This menu allows user to select the proper network manually for SiPTel IP Phone setup.  
STEP 1  
Select ‘2: Network’ from SETUP menu.  
Press 2 or select ‘2. Network’ using navigation keys and press OK  
<Setup>  
key.  
1: My Phone  
2: Network  
STEP 2  
Select ‘2: Mode Select’.  
Press 2 or select ‘2: Mode Select’ using navigation keys and press  
<NETWORK>  
1:Auto Detect  
2:Mode Select  
OK key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.4.2.1.1. Static IP User  
If you are a static IP user, select this menu and setup the static related settings required for using the  
SiPTel IP Phone.  
STEP 1  
Select ‘1: LAN (Static)’ in menu selection.  
Press 1 or select ‘1: LAN (Static)’ using navigation keys and press  
<Network Mode>  
1:LAN(Static)  
2:DHCP  
OK key.  
STEP 2  
Enter the IP address for the SiPTel IP Phone. You can use * to get a dot between octets.  
Enter the IP Address given by the ISP and press OK key.  
?
Ex: To enter 61.54.235.53 you would key in  
<Static>  
1:IP  
61.54.235.53  
61*54*235*53  
STEP 3  
Enter the Subnet Mask  
Enter the Subnet Mask given by the ISP and press OK key.  
Ex: To enter 255.255.255.0, you would key in  
<Static>  
2: Subnet Mask  
255.255.255.0  
255*255*255*0  
STEP 4  
Enter the Gateway IP address  
Enter the Gateway IP Address given by the ISP and press OK key.  
Ex: To enter 61.54.235.254, you would key in  
61*54*235*254  
<Static>  
3: Gateway  
61.54.235.254  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 5  
Enter the DNS Server IP address, and press ‘OK’ button.  
Enter the DNS IP Address given by ISP and press OK.  
<IP>  
4:DNS1  
202. 54. 30. 1  
Here you can give three DNS Addresses of you choice and press  
OK after each DNS entry.  
Ex: To enter 202.54.30.1, you would key in 202*54*30*1  
STEP 6  
If you want to apply the new setting, press ‘OK’ button.  
Use left arrow key in navigation keys to select YES and press OK  
Apply  
New Setting?  
YES  
NO  
STEP 7  
Reboot the SiPTel IP Phone to use new IP that is configured.  
Select YES using navigation keys and wait till the rebooting process  
is completed.  
Reboot System?  
YES NO  
4.4.2.1.2. DHCP User  
If you are a cable modem user or using a DHCP network, please select this menu and setup the required  
settings.  
STEP 1  
Select ‘2: DHCP’ from NETWORK mode menu under SETUP menu.  
Press 2 or select ‘2: DHCP using navigation keys and press OK key.  
<Network Mode>  
1: LAN (Static)  
2:DHCP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select ‘YES’ to select DHCP, and press ‘OK’ button.  
Use left arrow button from navigation keys to select ‘YES’ option and  
press OK key.  
Select DHCP?  
YES  
NO  
STEP 3  
After a while you’ll be able to see the following screen  
Use left arrow button from the navigation key to select YES and  
press OK button to reboot the IP Phone.  
Reboot system?  
YES  
NO  
4.4.2.1.3. PPPoE (ADSL) User  
If you are a PPPoE / ADSL user, please go through the following setup, with the required user-id and  
password in hand to configure on SiPTel IP Phone.  
STEP 1  
Select ‘3: PPPoE’ to setup PPPoE / ADSL related parameters from ‘NETWORK MODE’  
under ‘SETUP’ menu.  
Press 3 or select ‘3: PPPoE using navigation keys and press OK  
key.  
<Network Mode>  
2: DHCP  
3:PPPoE  
STEP 2  
Enter the username / ID given by your ISP as ADSL ID.  
Enter the User ID for ADSL / PPPoE given by your ISP.  
?
<PPPoE Setup>  
1: PPPoE ID  
XXXXXXX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 3  
Enter the password for your ADSL ID.  
Enter the Password related to the User ID of your ADSL / PPPoE.  
?
<PPPoE Setup>  
2: PPPoE PW  
XXXXXXX  
STEP 4  
Select ‘YES’ to apply the new setting, and press ‘OK’ button.  
Use navigation key to select the option YES and wait for a while.  
Apply  
New Setting?  
YES NO  
STEP 5  
Select ‘YES’ to reboot the system, and press ‘OK’ button.  
Use navigation key to select the YES and let the device reboot with  
the new settings to use PPPoE.  
Reboot system?  
YES NO  
It may take rather long time for the phone to get the connected to the ADSL service provider. In this case,  
SiPTel IP Phone will constantly make attempts to get connected, wait for a while.  
4.4.3. Call Setup  
Call Setup allow the user to change the priority of gatekeeper selection.  
STEP 1  
Select ‘3: Call Setup’ from SETUP menu.  
Press 3 or select ‘3. Call Setup’ using navigation keys and press OK  
key.  
<Setup>  
2: Network  
3: Call Setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select ‘1. GK Selection[GKx]’ and press ‘OK’ button.  
Just press OK button here as there will be only one option for  
selection.  
<Service>  
1.: GK Selection [GK1]  
Press CANCEL button to leave thing as it is.  
STEP 3  
Select GK option that are available from GK1 to GK6.  
Use navigation key to select any GK and press OK.  
Press CANCEL button to go back to upper menus  
<GK Select : [1]>  
1 : GK1  
2 : GK2  
STEP 4  
Select ‘YES’ to apply the new setting, and press ‘OK’ button.  
Use navigation key to select the option YES and wait for a while.  
Apply  
New Setting?  
YES NO  
STEP 5  
Select ‘YES’ to reboot the system, and press ‘OK’ button.  
Use navigation key to select the YES and let the device reboot. The  
Phone will not try to register to the new gatekeeper that you have  
just selected.  
Reboot system?  
YES NO  
4.4.4. Modem  
This menu is to set the modem related settings. User can enter the information required for connecting to  
the dial-up ISP etc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 1  
Select ‘4. Modem’ from SETUP menu after pressing MENU button.  
Press 4 or select ‘4: Modem’ using navigation keys and press OK  
key.  
<Setup>  
3: Call Setup  
4: Modem  
4.4.4.1. Editing Profile  
This menu is used to configure the ISP account to be used to connect to a dial-up ISP. ISP account  
includes dial-up ISP access phone number, user ID, and user password. User can edit the profiles up to  
3, and each profile consists of IST tel no., user ID, and user password.  
STEP 1  
Select ‘1: Profile1’.  
You can select any three of profile options available as first 3 menu  
options.  
<Modem>  
1:Profile1[101]  
2:Profile2[102]  
Use the navigation key or menu number to select the menu, and  
press ‘OK’ button.  
STEP 2  
Select ‘1 : Name [Profile1] to enter the name of the ISP  
Press 1 or use the up and down arrow keys to select the Name  
option and press OK.  
?
<Edit Prof 1>  
1. Name [profile1]  
2. Tel [101]  
STEP 3  
Enter the name to be used to discriminate the profile.  
Use ‘Menu’ key to toggle the character input mode.  
Press OK key after editing the Name.  
<Profile Name>  
My ISP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 4  
Select ‘2 : Tel [101] to enter the telephone number of the ISP  
Press 2 or use the up and down arrow keys to select the Telephone  
option and press OK.  
?
<Edit Prof 1>  
1. Name [MyISP]  
2. TEL [01410]  
STEP 5  
Enter the telephone number of the ISP for the profile.  
Use ‘Menu’ key to toggle the character input mode.  
Press OK key after editing the telephone number  
<Profile Tel#>  
172233  
STEP 6  
Select ‘3 : ID [uid1] to enter the username of the ISP  
Press 3 or use the up and down arrow keys to select the ID option  
and press OK.  
?
<Edit Prof 1>  
2. TEL [172233]  
3. ID [uid1]  
STEP 7  
Enter the username for the ISP of this profile.  
Use ‘Menu’ key to toggle the character input mode.  
Press OK key after editing the username  
<Profile ID>  
my username  
STEP 8  
Select ‘4 : PWD [pwd1] to enter the password of the ISP  
Press 4 or use the up and down arrow keys to select the PWD  
option and press OK.  
?
<Edit Prof 1>  
3. ID [uid1]  
4. PWD [pwd1]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 9  
Enter the password for the ISP of this profile. If you want to edit the existing password,  
use ‘Delete’ key.  
Use ‘Menu’ key to toggle the character input mode.  
Press OK key after editing the password  
<Profile PWD>  
my password  
4.4.4.2. ACT: [Profile]  
This menu is to select one of the three profiles that are available for you to use while pressing DIALUP  
(@ISP) button  
STEP 1:  
Select ‘4:ACT:[Prof-1] using navigation buttons.  
Press ‘OK’ button or select ‘5’ key to select the menu.  
<Modem>  
4:ACT[1:My ISP]  
5. Modem Option  
STEP 2:  
Select the desired profile. For example, let’s select ‘2: Profile’.  
Press the menu number or use the navigation key to select the  
Profile number and press ‘OK’ key  
<ACT : MyISP>  
1: My ISP  
2: Profile2  
4.4.4.3. Modem Options  
4.4.4.3.1. Country Code  
STEP 1  
Select ‘1: Country Code’  
Press 1 or select ‘1: Country Code’ using navigation keys and press  
OK key.  
<Modem Option>  
1:Country Code  
2: Dial Type [Pu]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select your country. This is also important to get proper time displayed on SiPTel screen.  
Use left and right arrow button in the navigation keys to select your  
Country press OK key.  
<Country Code>  
[33]  
India  
4.4.4.3.2. Dial Type  
STEP 1  
Select ‘2: Dial Type’.  
Press 2 or select ‘2: Dial Type [Pu]’ using navigation keys and press  
OK key.  
<Modem Option>  
1: Country Code  
2:Dial Type[Pu]  
STEP 2  
Select ‘1: Tone’ Or ‘2: Pulse’  
Press 1 or 2 or select ‘1: Tone’ or ‘2: Pulse’ using navigation keys  
and press OK key.  
<Type: Pulse>  
1:Tone  
2: Pulse  
4.4.4.3.3. Time Out  
This menu is to set the time delay that make the dial-up modem disconnected automatically after the time  
pre-set in case the user is not using the dial-up. The unit here is one minute.  
STEP 1  
Select ‘3: Timeout’.  
Press 3 or select ‘3: Timeout: [60]’ using navigation keys and press  
OK key.  
<Modem Options>  
3:TimeOut : [60]  
4: Speaker [Off]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Enter the Time Out value. The range is 0 ~ 255 minutes.  
Enter the time-out value, and press ‘OK’ button.  
<Time Out>  
Range [0-255]  
60  
4.4.4.3.4. Speaker  
This menu is to select whether you will hear the modem connection beep sound or not.  
Modem sound, though it is rather unpleasant to hear, it can be helpful to check the modem connection  
status by hearing the sound.  
STEP 1  
Select ‘4: Speaker’ in menu selection.  
Press 4 or select ‘4: Speaker [Off]’ using navigation keys and press  
OK key.  
<Modem>  
3: Time out [30]  
4: Speaker [Off]  
STEP 2  
Select whether you will hear the modem sound or not.  
Press 1 or 2 or select ‘1: On’ or ‘2: Off’ using navigation keys and  
press OK key.  
?
<Speaker [On] >  
1: On  
2: Off  
4.4.5. Time  
Time options specifically helps the IP Phone in properly displaying your timings of calls etc., basing on  
your local time instead of an universal time. SiPTel IP Phone automatically reaches one of our time  
servers to get you the correct time and this selection allows it to adjust the time according to your area.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 1  
Select ‘5.TIME’ from SETUP menu list after pressing MENU key.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu.  
<Setup>  
4: Modem  
5: Time  
4.4.5.1. Time Zone  
STEP 1  
Select “1: Time Zone’ from TIME menu under SETUP.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu  
<Time>  
1 : Time Zone  
2 : Summ Time [Di]  
STEP 2  
User Navigational keys to select the Time Zone for your country or area.  
Press ‘Cancel’ button to move to the upper menu.  
Time Zone  
+05:30  
4.4.5.2. Summer Time ( Day light settings )  
Some areas on GLOBE requires DAY light settings for correct time in some seasons.  
STEP 1  
Select “2:Summ Time[Di]”  
Use navigation key or press the menu number to select the menu.  
<Time>  
1 : Time Zone  
2 : Summ Time [Di]  
Press ‘Cancel’ button to move to the upper menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select ENABLE / DISABLE as per your area’s requirement.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu.  
<Summ Time:Di>  
1 : Enable  
2 : Disable  
4.4.6. PSTN  
The general telephone network that we have for our Fixed Wire Phones at home are technically known as  
PSTN – Public Switched Telephone Network  
4.4.6.1. Dial Type  
STEP 1  
Select ‘6.PSTN’ from the MAIN menu after pressing MENU button.  
Use navigation key and press OK or press the menu number to  
select the menu.  
<Setup>  
5: Time  
6: PSTN  
Press ‘Cancel’ button to move to the upper menu.  
STEP 2  
Select ‘2. Dial Type’ from PSTN menu.  
Use navigation key and press OK or press the menu number to  
select the menu.  
<PSTN Setup>  
2: Dial Type [Pu]  
3: Country Code  
Press ‘Cancel’ button to move to the upper menu.  
STEP 3  
Select either TONE / PULSE depending on what is supported by your Telephone Service  
Provider. PULSE also allows TONE enabled lines to work.  
Use navigation key and press OK or press the menu number to  
select the menu.  
<Type : Pulse >  
1 : Tone  
2 : Pulse  
Press ‘Cancel’ button to move to the upper menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.4.6.2. Default Call.  
Default Call allows you to select whether VOIP or PSTN should work as default when the phone goes off-  
Hook. This option mainly required when u have both CABLE and PSTN connected to the same phone for  
both VOIP and PSTN calls. If you are only a Dialup user, then no need to worry about this option because  
PSTN port is already busy as connected to ISP for internet.  
STEP 1  
Select ‘5: Dflt Call’ from the PSTN menu.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu.  
<PSTN Setup>  
4: RingDuration  
5: Dflt Call [Vo]  
STEP 2  
Select ‘2: VoIP’ to be on VoIP using cable and when not connected to ISP or not  
registered to VoIP Service, PSTN can be available. You can also shift between modes by  
press PSTN button as well when using CABLE Internet for VoIP  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu.  
<Dflt Call:Vo>  
1 : PSTN  
2 : VoIP  
4.4.7. HTTP PROXY  
HTTP Proxy is included in the phone so as to avoid hindrances for BALANCE option web access due to  
proxy servers in between.  
STEP 1  
Select ‘7.HTTP Proxy’ from the MAIN menu.  
Use navigation key and press OK or press the menu number to  
select the menu.  
<Setup>  
6: PSTN  
7: HTTP Proxy  
Press ‘Cancel’ button to move to the upper menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.4.7.1.  
Proxy IP  
STEP 1  
Select ‘1. IP’ to enter IP Address of your local proxy server.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ button to move to the upper menu.  
<HTTP Proxy>  
1: IP  
2: Port[0]  
STEP 2  
Enter Proxy IP address or DNS name of your local proxy.  
Press OK after entering the Proxy IP or its DNS name  
Press ‘Cancel’ button to move to the upper menu.  
HTTP Proxy IP  
IP :  
proxy.isp.com  
4.4.7.2.  
Proxy Port  
STEP 1  
Select ‘2. Port’ to enter Port that is used for proxying your traffic.  
Use navigation key and press OK or press the menu number to  
select the menu.  
<HTTP Proxy>  
1: IP  
2: Port[0]  
Press ‘Cancel’ button to move to the upper menu.  
STEP 2  
Enter the proxy port number and press OK.  
Press ‘Cancel’ button to move to the upper menu.  
HTTP Proxy Port  
Port:  
8080  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
4.5. Information  
This menu is to provide users with the information on the SiPTel IP Phone such as network setting and  
version, Mac address etc.  
4.5.1. Network  
This menu shows the network status the phone is employed, which includes IP address, subnet mask,  
default gateway, and DNS etc. In case of modem, it also shows the speed at which the modem got  
connected to ISP.  
STEP 1  
STEP 2  
Press ‘Menu’ key.  
Select ‘5: Information’, and press ‘OK’ button.  
Use navigation key or press the menu number to select the menu.  
<Menu>  
4: Setup  
5:Information  
Press ‘Cancel’ button to move to the upper menu.  
STEP 3  
Select ‘1: Network’, and press ‘OK’ button.  
Press ‘Cancel’ button to move to the upper menu.  
<Information>  
1:Network  
2: Version  
STEP 4  
You can see the network mode information. The following display shows that the current  
network mode is DHCP. The network mode can be Static, DHCP, PPPoE (or Dialup).  
Use navigation key to see the next information...  
Press ‘Cancel’ key to return to the upper menu.  
<Info. #1>  
Network Mode  
DHCP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 5  
You can see the SiPTel IP Phone IP information in the second information display.  
Use navigation key to see the next information.  
<Info. #2>  
IP  
XXX.XXX.XXX.XXX  
Press ‘Cancel’ key to return to the upper menu.  
STEP 6  
You can see the subnet mask information in the third information display.  
Use navigation key to see the next information.  
Press ‘Cancel’ key to return to the upper menu.  
<Info. #3>  
Subnet Mask  
XXX.XXX.XXX.XXX  
STEP 7  
You can see the gateway address information in fourth information display.  
Use navigation key to see the next information.  
<Info. #4>  
Gateway  
XXX.XXX.XXX.XXX  
Press ‘Cancel’ key to return to the upper menu.  
STEP 8  
You can see the DNS address information in the fifth information display.  
Use navigation key to see the next information.  
Press ‘Cancel’ key to return to the upper menu.  
<Info. #5/6/7>  
DNS1/2/3  
XXX.XXX.XXX.XXX  
4.5.2. Version  
Version information is important especially when upgrading the firmware to the latest version. If you have  
any problem in the SiPTel IP Phone, please report the version information, and the IP address of the  
phone to the service provider.  
STEP 1  
Press ‘Menu’ button on the key pad of SiPTel IP Phone.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Select ‘5: Information’ in menu selection.  
Press OK button or Press 5 to select.  
<Menu>  
4: Setup  
5: Information  
STEP 3  
Select ‘2: Version’ from the menu.  
Press OK button or Press 2 to select.  
<Information>  
1: Network  
Press ‘Cancel’ key to return to the upper menu.  
2: Version  
STEP 4  
You can see the following display. ‘Boot’ means the boot ROM version, and App means  
the firmware version.  
Press ‘Cancel’ keys to go back in the menu structure.  
<SW Version>  
Boot: V2.07  
App: V5.2E--15  
4.6. BALANCE  
This option is provided so as to check you balance online using phone. And so, this option works only  
when phone is connected to Internet.  
STEP 1  
Select ‘6: BALANCE’ from the MAIN menu selection.  
Use navigation key or press the menu number to select the menu.  
<Menu>  
6: BALANCE  
7: Reboot  
Press ‘Cancel’ key to return to the initial display.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
You will see following screen while it attempts to get your account balance.  
It may take few seconds depending on the speed of internet to get  
the account balance.  
<Account>  
BALANCE:  
WAIT A MOMENT  
Please wait for a moment.  
STEP 4  
You will see the account balance there after.  
It displays your account balance after “USD: “  
Press Cancel to go back to main menu.  
<Account>  
BALANCE:  
USD 10.02  
4.7. Reboot  
This menu is used to reboot the system.  
STEP 1  
Select ‘7: Reboot’ in the MAIN menu selection.  
Use navigation key or press the menu number to select the menu.  
Press ‘Cancel’ key to return to the initial display.  
<Menu>  
6: BALANCE  
7: Reboot  
STEP 2  
If you want to reboot SiPTel IP Phone, select ‘YES’, and press ‘OK’ .  
Use navigation key to select ‘YES’ or ‘NO’.  
Reboot System?  
YES NO  
Press ‘Cancel’ key to return to the initial display.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
5. Using SiPTel IP Phone  
5.1. Connecting IP phone to Internet  
5.1.1. Using in Dial-up Mode  
STEP 1  
Press @ISP button on the key pad of SiPTel IP Phone. The built-in modem will try to  
connect to the dial-up ISP preset in Modem setup.  
If you want to cancel to connect to an ISP, please press ‘@isp’  
button again.  
[Dial-UP]  
Connecting  
Wait a moment  
STEP 2  
If you can see ‘ATDT + dial-up ISP Tel number’ on the LCD, it means that the modem is  
trying to call your local ISP telephone number.  
ATDT specified the dialtype as TONE and  
ATDP specifies the dialtype as PULSE.  
OK  
ATDT 172233  
XXXXX  
STEP 3  
If you can see ‘PPP Start’ message on the LCD, it means that the connection to the dial-  
up ISP is succeeded.  
If you can’t see the left display, please try again.  
XXXXXXXX  
Connect 34667  
PPP Start  
STEP 4  
If you can see the following display, it means that the connection is successful, and  
SiPTel IP Phone has obtained a Dynamic IP address from the dial-up ISP.  
If you can’t see the left display, please try again.  
IP: XXX.XXX.XXX.XXX  
Connection OK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 5  
If you can see the following display, you can dial the destination number to make a call.  
Please wait till the SiPTel IP Phone can be registered with the  
SiP Tel  
10-100-1000  
Gatekeeper of ITSP.  
A 09:24  
If you can see constant top left display , you can dial the number.  
5.1.2. Using with Broadband Cable.  
Once the network is properly configured using the Network menu option, you can straight away start  
making calls once the IP Phone is registered with the Gatekeeper of ITSP. See if SiPTel IP Phone  
registered with the Gatekeeper of ITSP.  
If you can’t see constant top left display, please check the network  
SiP Tel  
10-100-1000  
once again or check your balance and your H.323 ID account  
configuration as well.  
A 09:24  
5.2. Making a VoIP Call  
User can make or receive a call in either VoIP mode or PSTN mode. There are some differences between  
VoIP mode and PSTN mode. Please read carefully the following description not to make have confusion  
in making or receiving a call.  
Note: Use pound key(#) to make a call immediately after dialing the destination phone number in VoIP mode.  
5.2.2. In On-Hook mode (Pre-dial)  
This is used to dial the destination number without picking up the handset.  
STEP 1  
Dial destination number in on hook mode. The dialed number will be displayed on LCD.  
Enter the full number of the destination device.  
Here you can correct the digits if you make mistakes and complete  
the number.  
Pre-dial  
A12:00  
021231234  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 2  
Pick up the handset or Press Speaker button. The call will be dialed to the destination  
number automatically.  
Please wait till the call is placed successfully.  
Dialing  
021231234  
A12:00  
STEP 3  
If the call is connected to the destination TEL number, the duration of the ongoing calls  
will appear on the LCD display.  
Once the call is connected to the destination party, start your  
conversation.  
[00:37]  
021231234  
A12:00  
5.2.3. In Off Hook mode  
STEP 1  
Pick up the handset, and try to hear the dial tone.  
In this mode you cannot correct your dialed digits. If you go wrong  
somewhere with digits, hang the phone and try dialing again.  
PRESS DIAL..  
A 1 2 : 0 0  
STEP 2  
Dial the destination telephone number.  
You can press ‘#’ key to make the phone call immediately after  
PRESS DIAL..  
A 1 2 : 0 0  
dialing the destination number otherwise a delay of 2-3 seconds can  
be observed.  
021231234  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
STEP 3  
If the call is connected to the destination party successfully, the call starting time, and call  
duration time will be displayed on the LCD.  
If you can see the icon  
the phone.  
on the LCD, you can start to speak over  
12:00  
021231234  
[00:37]  
A12:00  
5.3. Making a PSTN call  
To use PSTN mode, you need to connect the PSTN port of SiPTel IP Phone to the phone line. Please  
remember, you are not allowed to make any local call when you are in Dialup because your phone line is  
already connected to local ISP for Internet to make VoIP calls.  
If Broadband cable is used for VoIP registration and the PSTN port is connected to the PSTN network,  
you can still make a PSTN call by pressing ‘PSTN’ button on the key pad of the SiPTel IP Phone.  
In case the broadband is unavailable or your account is not registered our ITSP service, it’s impossible to  
use VoIP mode. In this case, the SiPTel IP Phone will be changed to the PSTN mode automatically when  
you go off hook.  
STEP 1  
Press the ‘PSTN’ key on the key pad of the SiPTel IP Phone.  
When you are using PSTN mode, you can see the [PSTN] message  
[PSTN]  
on the LCD.  
If you can dial tone, start dialing the destination number.  
A12:00  
5.4. Making a call in Phone Book mode  
STEP 1  
STEP 2  
STEP 3  
STEP 4  
STEP 5  
Press ‘P-BOOK’ button, or press ‘MENU’ and select “2: Phone Book”.  
Select ‘1 : Find Number’ in Phone Book menu.  
Select either ‘By Index’ or ‘By Name’.  
Enter the INDEX number or NAME and press OK button.  
Pick up the handset. The call will be made to the select number.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SiPTel C01 IP Phone User Manual  
5.5. Making a call in Call Log mode  
STEP 1  
STEP 2  
STEP 3  
STEP 4  
Press ‘Call Log’ button, or press ‘MENU’ and select ‘1: Call Log’.  
Select either ‘Received Calls’, ‘Dialed Calls’, or ‘TX/Rx Calls’ etc.,  
Select the desired number.  
Pick up the handset. The call will be made to the selected number.  
5.6. Memory Dial  
STEP 1  
STEP 2  
Pickup the hand set.  
Press the memory dial key [M1~M3] on the key pad of the SiPTel IP Phone. The one  
button touch call will be made immediately.  
5.7. Web Access  
After connecting your IP Phone on cable network or dialup, you can view the IP Address from  
INFORMATION -> NETWORK menu on LCD. Try the following on a browser using that IP from a PC.  
Username and password can be acquired from your vendor.  
For further Inquiries  
Download from Www.Somanuals.com. All Manuals Search And Download.  

PYLE Audio TV Receiver PLTVATSC1 User Guide
Remington Chainsaw EL 8 107624 01, EL 8 107624 02, EL 8 107625 01, EL 8 107625 02, EL 8 111174 01 User Guide
Remington Power Tools Chainsaw M15014AS User Guide
Revox Speaker Resound L 120 User Guide
RocketFish Computer Drive RF ICAP12 User Guide
Salton Beverage Dispenser WC22RE User Guide
Samsung Camcorder HDR CX7E User Guide
Samsung CRT Television BN68 04501A User Guide
Seagate Computer Drive 2160N User Guide
Sears Washer 58075133 User Guide